Siemens OpenStage 10 T Service manual

Documentation
HiPath 500, HiPath 3000/5000, HiPath 4000
OpenStage 10 T, OpenStage 15 T, OpenStage 20 T,
OpenStage 30 T, OpenStage 40 T, OpenStage 60 T,
OpenStage 80 T
Administration Manual
Communication for the open minded
Siemens Enterprise Communications
www.siemens-enterprise.com
bkTOC.fm
Nur für den internen Gebrauch
Content
Content
0
1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 About the Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.1 OpenStage 60 T/80 T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.2 OpenStage 40 T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.3 OpenStage 30 T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.4 OpenStage 20 T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.5 OpenStage 15 T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.6 OpenStage 10 T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4 Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-1
1-2
1-3
1-3
1-4
1-5
1-6
1-7
1-8
1-9
2 Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Assembling and Installing the Phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.1 Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.2 Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.3 Connectors at the bottom side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.3.1 OpenStage 60 T/80 T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.3.2 OpenStage 40 T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.3.3 OpenStage 30 T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.3.4 OpenStage 20 T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.3.5 OpenStage 15 T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.3.6 OpenStage 10 T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.4 Connecting the Phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.5 Power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-1
2-1
2-1
2-1
2-2
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
3 Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1 Access via Local Phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2 IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.3 Password timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.4 Bluetooth adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
3.5 Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.5.1 Canonical Dialing Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.5.2 Canonical Dial Lookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3.6 Pixel saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3.7 Display General Phone Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3.7.1 Software ver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3.7.2 Last restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
3.8 Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
0-1
bkTOC.fm
Content
Nur für den internen Gebrauch
3.9 Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
3.10 Restart Phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
4 Examples and HowTos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1 Canonical Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1.1 Canonical Dialing Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1.2 Canonical Dial Lookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
4.2 Transferring Phone Software and Media Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
4.2.1 Phone Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
4.2.1.1 Installation Using a USB Memory Stick (OpenStage 60 T/80 T) . . . . . . . . . . . 4-3
4.2.2 Media Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
4.2.2.1 Picture Clips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
4.2.2.2 Screensaver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
4.2.2.3 Ringer File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
4.3 optiPoint Compatible Mode (V2R0). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
4.3.1 Switching Procedure for OpenStage 15 / 30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
4.3.2 Switching Procedure for OpenStage 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
4.3.3 Key Mapping in optiPoint Mode (HiPath 3000). . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
4.3.3.1 optiPoint 500 Entry / OpenStage 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9
4.3.3.2 optiPoint 500 Standard / OpenStage 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
4.3.3.3 optiPoint 500 Advance / OpenStage 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
5 Local Phone Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Z-1
0-2
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
uebersicht.fm
Overview
Important Notes
1
Overview
1.1
Important Notes
Q
For safety reasons, the phone can only be supplied with power by the original power
supply unit Æ page 9.
Never open the telephone or add-on equipment. If you encounter any problems, contact System Support.
Use only original Siemens accessories!
Using other accessories may be dangerous, and will invalidate the warranty, extended
manufacturer’s liability and the CE mark.
Installation requirement for USA, Canada, Norway, Finland and Sweden: Connection
to networks which use outside cables is prohibited. Only in-house networks are permitted.
7
For USA and Canada only:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This product is a UL Listed Accessory, I.T.E., in U.S.A. and Canada.
This equipment also complies with the Part 68 of the FCC Rules and the Industrie
Canada CS-03.
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
1-1
uebersicht.fm
Overview
About the Manual
1.2
About the Manual
The instructions within this manual will help you in administering and maintaining the phones
OpenStage 10 T, OpenStage 15 T, OpenStage 20 T, OpenStage 30 T, OpenStage 40 T,
OpenStage 60 T and OpenStage 80 T. The instructions contain important information for safe
and proper operation of the phones. Follow them carefully to avoid improper operation and get
the most out of your multi-function telephone in a network environment.
This guide is intended for service providers and network administrators. The tasks described
in this guide are not intended for end users. Many of these tasks affect the ability of a phone to
function on the network and require an understanding of telephony concepts.
These instructions are laid out in a user-oriented manner, which means that you are led through
the functions of the OpenStage TDM phone step by step, wherever expedient. For the users,
a separate manual is provided.
You can find further information on the official Siemens Enterprise Communications website:
http://www.enterprise-communications.siemens.com
and on the Siemens Enterprise Wiki:
http://wiki.siemens-enterprise.com/
1-2
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
uebersicht.fm
Overview
User Interface
1.3
User Interface
1.3.1
OpenStage 60 T/80 T
9
5
2
1
6
7
8
3
4
10
1
The handset lets you pick up and dial calls in the usual manner.
2
The display provides intuitive support for telephone operation.
3
The user-friendly mode keys t, u, v, w, x and y provide easy access to your telephone’s applications. To select a tab within a function press the relevant key repeatedly
until the required tab is displayed.
4
With the TouchGuide, the user/administrator can navigate in the various phone functions, applications, and configuration menus.
5
You can customize your telephone in line with your personal needs by assigning individual phone numbers and functions to the free programmable sensor keys.
6
Press the function keys s, r and q to access frequently used telephony functions.
7
The audio keys -, n, +, o and p let you optimize the audio settings on your
telephone.
8
With the TouchSlider, the user can adjust the volume, e.g. of ringtones.
9
The keypad is used for entering phone numbers and text.
10
Inbound calls are visually signaled on the call display.
The only difference between the OpenStage 80 T and OpenStage 60 T is their housings.
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
1-3
uebersicht.fm
Overview
User Interface
1.3.2
OpenStage 40 T
9
2
3
1
4
6
5
7
8
1
The handset lets you pick up and dial calls in the usual manner.
2
The display provides intuitive support for telephone operation.
3
You can customize your telephone in line with your personal needs by assigning
individual phone numbers and functions to the free programmable sensor keys.
4
Press the function keys s, , and r to access frequently used telephony functions.
5
Mailbox key O and menu key N.
6
The audio keys -, n, +, o and p let you optimize the audio settings on your
telephone.
7
With the 5-way navigator, the user/administrator can navigate in the various phone
functions, applications, and configuration menus.
8
The keypad is used for entering phone numbers and text.
9
Inbound calls are visually signaled on the call display.
1-4
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
uebersicht.fm
Overview
User Interface
1.3.3
OpenStage 30 T
2
1
6
3
7
4
9
8
1
The handset lets the user pick up and dial calls in the usual manner.
2
The display provides intuitive support for telephone operation.
3
The audio keys -, n, and +, let the user optimize the audio settings on his telephone.
4
With the mailbox key O and menu key N, the user can access the service menu or
the mailbox.
5
With the function keys s, , and r, the user can access the frequently used telephony functions release, redial, and call forwarding.
6
With the headset key, the user can answer calls, for instance. With the microphone key,
he can prevent the other party from hearing internal conversations.
7
The keypad is used for entering phone numbers and text.
8
With the navigation keys, the user/administrator can navigate in the various phone
functions, applications, and configuration menus.
9
The user can customize his telephone in line with his personal needs by assigning
individual phone numbers and functions to the free programmable sensor keys.
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
1-5
uebersicht.fm
Overview
User Interface
1.3.4
OpenStage 20 T
1
2
3
4
5
6
7
1
The handset lets you pick up and dial calls in the usual manner.
2
The display provides intuitive support for telephone operation.
3
Press the function keys s, ,, r and p to access frequently used telephony
functions.
4
Mailbox key O and menu key N.
5
The audio keys -, n and + let you optimize the audio settings on your telephone.
6
With the 3-way navigator, the user/administrator can navigate in the various phone
functions, applications, and configuration menus.
7
The keypad is used for entering phone numbers and text.
1-6
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
uebersicht.fm
Overview
User Interface
1.3.5
OpenStage 15 T
1
2
3
4
5
6
7
1
The handset lets you pick up and dial calls in the usual manner.
2
The display provides intuitive support for telephone operation.
3
The audio keys let you optimize the audio settings on your telephone.
4
O mailbox key and N menu key.
5
The keypad is used for entering phone numbers and text.
6
With the navigaton keys, the user/administrator can navigate in the various phone functions, applications, and configuration menus.
7
You can customize your telephone in line with your personal needs by assigning individual phone numbers and functions to the free programmable keys.
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
1-7
uebersicht.fm
Overview
User Interface
1.3.6
OpenStage 10 T
1
2
3
4
1
The handset lets you pick up and dial calls in the usual manner.
2
You can customize your telephone in line with your personal needs by assigning
individual phone numbers and functions to the free programmable keys.
3
The audio keys let you optimize the audio settings on your telephone.
4
The keypad is used for entering phone numbers and text.
1-8
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
uebersicht.fm
Overview
Administration
1.4
Administration
The OpenStage TDM telephones mainly will be equipped by the HiPath Communication
System it is connected to. For further information refer to the corresponding Service Manual.
Beside the main administration via the Communication System, there are view parameters
which can be set for the OpenStage 60 T/80 T telephone individually via Local Menu.
These parameters are described in Section 3, "Administration".
With the functionality of the OpenStage Manager, the user can personalize his
OpenStage 60 T/80 T telephone with own pictures and ringtone files and also customize the
personal phonebook.
You can find a short overview of these functions in Section 4.2.2, "Media Files".
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
1-9
uebersicht.fm
Overview
Administration
1-10
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
inbetriebnahme.fm
Startup
Prerequisites
2
Startup
2.1
Prerequisites
The HiPath communications platform HiPath 500, HiPath 3000/5000 or HiPath 4000 is ready
to operate.
2.2
Assembling and Installing the Phone
2.2.1
Shipment
•
•
•
•
Telephone
Handset
Handset cable
Subpackage:
•
Document "Installation and Quick Reference Guide"
•
Emergency number sticker
>
2.2.2
Please pay attention to the notes on power supply on Section 1.1, "Important Notes"
and Section 2.2.5, "Power supply".
Assembly
1.
Handset: Insert the plug on the long end of the handset cable into the jack
on the base
of the telephone and press the cable into the groove provided for it. Next, insert the plug
on the short end of the handset cable into the jack on the handset.
2.
Emergency Number Sticker: Write your telephone number and those for the fire and police
departments on the included label and attach it to the telephone housing underneath the
handset (see arrow).
3.
OpenStage 60 T/80 T only: Before using the telephone, remove the protective covering
from the Navigator/TouchGuide ring surface.
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
2-1
inbetriebnahme.fm
Startup
Assembling and Installing the Phone
2.2.3
Connectors at the bottom side
2.2.3.1
OpenStage 60 T/80 T
USB
Countryspecific
cable
(e.g. 1st party CTI or OpenStage Manager)
USB memory stick
HiPath
Power supply
Headset
Key Module
Handset
2-2
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
inbetriebnahme.fm
Startup
Assembling and Installing the Phone
2.2.3.2
OpenStage 40 T
Countryspecific cable
Power supply
(if necessary)
HiPath
USB
(e.g.
1st party CTI)
Headset
Key Module
Busy Lamp Field
Handset
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
2-3
inbetriebnahme.fm
Startup
Assembling and Installing the Phone
2.2.3.3
OpenStage 30 T
Countryspecific cable
Power supply
(if necessary)
HiPath
USB
(e.g.
1st party CTI)
Key Module
Busy Lamp Field
2-4
Headset
Handset
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
inbetriebnahme.fm
Startup
Assembling and Installing the Phone
2.2.3.4
OpenStage 20 T
HiPath
Handset
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
2-5
inbetriebnahme.fm
Startup
Assembling and Installing the Phone
2.2.3.5
OpenStage 15 T
HiPath
Handset
Key Module
2-6
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
inbetriebnahme.fm
Startup
Assembling and Installing the Phone
2.2.3.6
OpenStage 10 T
HiPath
Handset
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
2-7
inbetriebnahme.fm
Startup
Assembling and Installing the Phone
2.2.4
Connecting the Phone
OpenStage 40 T standalone, OpenStage 20 T, OpenStage 15 T, OpenStage 10 T:
•
Insert the UP0/E cable into the jack
on the base of the telephone.
OpenStage 60 T/80 T, OpenStage 40 T with OpenStage Key Module 40:
1.
Insert the UP0/E cable into the jack on the power supply and connect the jack on the power
supply with jack on the base of the telephone.
2.
If applicable, connect the following optional jacks:
•
Headset (accessory)
•
Add-on device (Key Module, Busy Lamp Field)
•
USB slave for connection to PC
•
USB master for connection to an USB memory stick
2-8
7
To prevent damage on the OpenStage 60 T/80 T phone, connect an
USB memory stick using the adapter cable C39195-Z7704-A5.
7
Do not connect a USB hub to the phone’s USB port, as this may lead to
stability problems.
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
inbetriebnahme.fm
Startup
Assembling and Installing the Phone
2.2.5
Power supply
Depending on the phone type and amount of key modules (with display or key module 15), an
external power unit may be required. In the following table, the key module 15 (without display)
is explicitly indicated; otherwise, numbers refer to the key module with display. Please ensure
to to use the appropriate plug-in power supply.
Name of Phone
Key Modules
OpenStage 10 T
-
-
OpenStage 15 T
0 or 1 key
module 15
-
OpenStage 20 T
-
-
OpenStage 30 T
0 or 1
-
OpenStage 40 T
0 or 1 key
module 15
-
1 or 2
;
OpenStage 60 T
0, 1 or 2
OpenStage 80 T
0, 1 or 2
External Power Unit
;
;
The following accessories always need an external power unit:
•
OpenStage BLF
•
OpenStage Phone Adapter
>
The order no. for the plug-in power supply is region specific:
EU: L30250-F600-C141
UK: L30250-F600-C142
US: L30250-F600-C143
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
2-9
inbetriebnahme.fm
Startup
Assembling and Installing the Phone
2-10
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
administration.fm
Administration
Access via Local Phone
3
Administration
This chapter describes the configuration of every parameter available on the OpenStage 60 T/
80 T local admin menu.
The telephones OpenStage 10 T, OpenStage 15 T, OpenStage 20 T and OpenStage 40 T
can’t be administered via local Menu but only by the communication platform.
To customize the free programmable keys on the telephones OpenStage 10 T,
OpenStage 15 T, OpenStage 40 T and OpenStage 60 T/80 T see User Manual.
3.1
Access via Local Phone
>
The data entered in input fields is parsed and controlled by the phone. Thus, data is
accepted only if it complies to the value range.
1.
Access the Administration Menu
OpenStage 60 T/80 T:
Press the v key repeatedly until the "Settings" tab is displayed.
Select the "Admin" entry and confirm with i.
OpenStage 15 T / 20 T / 30 T / 40 T:
Press the keys D, l, and i consecutively to select the administration menu.
2.
Enter Password
When the Admin menu is active, you will be prompted to enter the administrator password.
The default admin password is "123456". It is highly recommended to change the password (see Section 3.8, "Password") after your first login.
For entering passwords with non-numeric characters, please consider the following:
By default, password entry is in numeric mode. For changing the mode, press the # key
once or repeatedly, depending on the desired character. The # key cycles around the input
modes as follows:
(Abc) -> (abc) -> (123) -> (ABC) -> back to start.
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
3-1
administration.fm
Administration
Access via Local Phone
3.
Navigate within the Administration Menu
OpenStage 60/80
Use the TouchGuide to navigate and execute administrative actions in the administration
menu.
Press the mkey briefly:
- scroll up
Press the h key:
- cancel a function
Press the i key:
- confirm entries
Press the g key:
- open a context menu
Press the l key briefly:
- scroll down
Run your finger around the
sensor ring W
- browse lists and menus
- set up volume
OpenStage 40
Use the 5-way Navigator to navigate and execute administrative actions in the administration menu.
Press the mkey briefly:
- scroll up
Hold down:
- scroll to top of list
Press the h key:
- cancel a function
- delete character left
of cursor
- up one level
Press the l key briefly:
- scroll down
Hold down:
- scroll to end of list
3-2
Press the i key:
- confirm entries
- perform an action
Press the g key:
- open a context menu
- down one level
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
administration.fm
Administration
Access via Local Phone
OpenStage 20
Use the 3-way Navigator to navigate and execute administrative actions in the administration menu.
Press the m key briefly:
- scroll up
Hold down:
- scroll to top of list
Press the l key:
- confirm entries
- perform an action
Press the l key briefly:
- scroll down
Hold down:
- scroll to end of list
OpenStage 15 / 30
Press the m key
briefly:
- scroll up
Press the OK key:
- confirm entries
- perform an action
Press the l key:
In idle mode:
- Open idle menu
In lists and menues:
- scroll down
4.
Select a parameter
If a parameter is set by choosing a value from a selective list, an arrow symbol appears in
the parameter field that has the focus. Press the key to enter the selective list. Use the Sensor Wheel resp. the m and l key to scroll up and down in the selective list. To select a list
entry, press the i key.
5.
Enter the parameter value
For selecting numbers and characters, you can use special keys. See the following table:
Key
Function
*
Switch to punctuation and special characters.
#
Toggle between lowercase characters, uppercase characters, and digits in
the following order:
(Abc) -> (abc) -> (123) -> (ABC) -> back to start.
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
3-3
administration.fm
Administration
Access via Local Phone
OpenStage 60/80
If a parameter is set by entering a number or character data, the onscreen keypad is used.
Press the i key to enter the editor. Within the editor, solely use the key numbers or the
Sensor Wheel for selecting numbers, characters, or groups of characters. The h key deletes one character in the input field, and the g key moves the cursor to the OK field.
The following figure describes the elements of the onscreen keypad and their functions:
Element with focus
Letters, digits, punctuation marks or special characters
Command line
Copy contents of active field to clipboard
Insert clipboard contents at cursor position
Move cursor left/right
Shift to punctuation and special characters
Shift to numeric entry
Shift to upper/lower case
Additionally, you can use the following keys on the keypad as shortcuts for the selection of
character groups
Element
Function
*
Switch to punctuation and special characters.
#
Toggle between lowercase characters, uppercase characters, and digits.
OpenStage 15/20/30/40
With the OpenStage 15/20/30/40, use the keypad for entering parameters. With the 3 way/
5 way navigator, you can enter, delete, copy and paste characters and numbers as well as
navigate within an entry and toggle the input mode.
6.
3-4
Save and exit
When you are done, select Save & exit and press
.
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
administration.fm
Administration
IP Address
3.2
IP Address
To establish a connection between the user’s PC and the phone via USB cable, an IP address
is necessary. It is preconfigured with 192.168.200.1, but can be edited.
Local Phone Menu
|---
Admin
|--- Network
|--- IP configuration
|--- IP address
3.3
Password timeout
With this entry you decide after which time of inactivity (in minutes) a password has to be reentered. The setting is valid for the admin password and for the user password.
Local Phone Menu
|---
Admin
|--- System
|--- Features
|--- Configuration
|--- General
|--- Not used timeout
3.4
Bluetooth adapter
You can read only the MAC adress of the phone’s bluetooth adapter.
Local Phone Menu
>
|
Bluetooth is available only on OpenStage 60/80 phones.
--- Admin
|
--- System
|
--- Features
|
--- Configuration
|
--- Bluetooth
|
--- Local device address
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
3-5
administration.fm
Administration
Dialing
3.5
Dialing
For correct synchronisation of Microsoft Outlook contacts via the OpenStage Manager, the canonical dialing settings must be configured appropriately.
3.5.1
Canonical Dialing Settings
Call numbers taken from a directory application are mostly expressed in canonical format.
Moreover, call numbers entered into the local phone book are automatically converted and
stored in canonical format, thereby adding "+", Local country code, Local national code, and
Local enterprise node as prefixes. If, for instance, the user enters the extension "1234", the
local country code is "49", the local national code is "89", and the local enterprise node is "722",
the resulting number in canonical format is "+49897221234".
For generating an appropiate dial string, a conversion from canonical format may be required.
The following parameters determine the local settings of the phone, like Local country code
or Local national code, and define rules for converting from canonical format to the format required by the PBX.
>
To enable the number conversion, all parameters not marked as optional must be
provided, and the canonical dial lookup settings must be configured (see Section
3.5.2, "Canonical Dial Lookup").
Data required
•
•
•
•
•
•
3-6
Local country code:
E.164 Country code, e.g. "49" for Germany, "44" for United Kingdom.
Maximum length: 5.
National prefix digit:
Prefix for national connections, e.g. "0" in Germany and United Kingdom.
Maximum length: 5.
Local national code:
Local area code or city code, e.g. "89" for Munich, "20" for London.
Maximum length: 6.
Min local num length:
Minimum number of digits in a local PSTN number, e.g. 3335333 = 7 digits.
Local enterprise node:
Number of the company/PBX wherein the phone is residing.
Maximum length: 10 (Optional)
PSTN access code:
Access code used for dialing out from a PBX to a PSTN.
Maximum length: 10. (Optional)
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
administration.fm
Administration
Dialing
•
•
•
•
•
International access code:
International prefix used to dial to another country, e.g. "00" in Germany and United Kingdom.
Maximum length: 5.
Operator code:
List of extension numbers for a connection to the operator. The numbers entered here are
not converted to canonical format.
Maximum length: 50. (Optional)
Emergency number:
List of emergency numbers to be used for the phone. If there are more than one numbers,
they must be separated by commas. The numbers entered here are not converted to canonical format.
Maximum length: 50. (Optional)
Initial extn. digits:
List of initial digits of all possible extensions in the local enterprise network. When a call
number could not be matched as a public network number, the phone checks if it is part of
the local enterprise network. This is done by comparing the first digit of the call number to
the value(s) given here. If it matches, the call number is recognized as a local enterprise
number and processed accordingly.
If, for instance, the extensions 3000-5999 are configured in the HiPath, each number will
start with 3, 4, or 5. Therefore, the digits to be entered are 3, 4, 5.
Internal numbers
>
To enable the phone to discern internal numbers from external numbers, it is
crucial that a canonical lookup table is provided (Section 3.5.2, "Canonical Dial
Lookup").
> Local enterprise form:
Default value. Any extension number is dialled in its simplest form. For an extension on the
local enterprise node, the node ID is omitted. If the extension is on a different enterprise
node, then the appropriate node ID is prefixed to the extension number. Numbers that do
not correspond to an enterprise node extension are treated as external numbers.
> Always add node:
Numbers that correspond to an enterprise node extension are always prefixed with the
node ID, even those on the local node. Numbers that do not correspond to an enterprise
node extension are treated as external numbers.
> Use external numbers:
All numbers are dialled using the external number form.
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
3-7
administration.fm
Administration
Dialing
•
External numbers
> Local public form:
Default value. All external numbers are dialled in their simplest form. Thus a number in the
local public network region does not have the region code prefix. Numbers in the same
country but not in the local region are dialled as national numbers. Numbers for a different
country are dialled using the international format.
> National public form:
All numbers within the current country are dialled as national numbers, thus even local
numbers will have a region code prefix (as dialling from a mobile). Numbers for a different
country are dialled using the international format.
•
> International form:
All numbers are dialled using their full international number format.
External access code
> Not required:
The access code to allow a public network number to be dialled is not required.
•
> For external numbers:
Default value. All public network numbers will be prefixed with the access code that allows
a number a call to be routed outside the enterprise network. However, international numbers that use the + prefix will not be given access code.
International gateway:
> Use national code:
Default value. All international formatted numbers will be dialled explicitly by using the access code for the international gateway to replace the "+" prefix.
> Leave as +:
All international formatted numbers will be prefixed with "+".
3-8
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
administration.fm
Administration
Dialing
Local Phone Menu
|---
Admin
|--- Local functions
|--- Locality
|--- Canonical settings
Local country code
National prefix digit
Local national code
Min local num length
Local enterprise node
PSTN access code
International access code
Operator code
Emergency number
Initial extn. digits
|---
Admin
|--- Local functions
|--- Locality
|--- Canonical dial
Internal numbers
External numbers
External access code
International gateway
3.5.2
Canonical Dial Lookup
The parameters given here are important for establishing outgoing calls and for recognizing incoming calls.
In the local phonebook numbers are stored in canonical format. In order to generate an appropriate dial string according to the settings in Internal numbers and External numbers (-> Section 3.5.1), internal numbers must be discerned from external numbers. The canonical lookup
table provides patterns which allow for operation.
Furthermore, these patterns enable the phone to identify callers from different local or international telephone networks by looking up the caller’s number in the phone book. As incoming
numbers are not always in canonical format, their composition must be analyzed first. For this
purpose, an incoming number is matched against one or more patterns consisting of country
codes, national codes, and enterprise nodes. Then, the result of this operation is matched
against the entries in the local phone book.
>
To make sure that canonical dial lookup works properly, at least the following parameters of the phone must be provided:
•
Local country code -> Section 3.5.1
•
Local national code -> Section 3.5.1
•
Local enterprise node -> Section 3.5.1
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
3-9
administration.fm
Administration
Dialing
Up to 5 patterns can be defined. The Local code 1 ... 5 parameters define up to 5 different local
enterprise nodes, whilst International code 1... 5 define up to 5 international codes, that is,
fully qualified E.164 call numbers for use in a PSTN.
Data required
•
Local code 1 ... 5:
Local enterprise code for the node/PBX the phone is connected to.
Example: "722" for Siemens Munich.
International code 1 ... 5:
Sequence of "+", local country code, local area code, and local enterprise node corresponding to to one or more phone entries.
Example: "+4989722" for Siemens Munich.
•
Local Phone Menu
|---
Admin
|--- Local functions
|--- Locality
|--- Canonical lookup
Local code 1
International code 1
Local code 2
International code 2
Local code 3
International code 3
Local code 4
International code 4
Local code 5
International code 5
3-10
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
administration.fm
Administration
Pixel saver
3.6
Pixel saver
By the time the screen of your phone is black, the pixel saver is activ to help save energy conservation. With this entry you decide after which time of inactivity (in hours 2- 8) the pixel saver
is to be activated.
Local Phone Menu
|---
Admin
|--- Local functions
|--- Locality
|--- Pixel saver
|--- Timeout (Hrs)
3.7
Display General Phone Information
General information about the status of the phone can be displayed, if desired.
3.7.1
Software ver.
Displays the version of the phone’s firmware.
3.7.2
Last restart
Shows date and time of the last reboot.
Local Phone Menu
|---
Admin
|--- General information
|--- Software ver.
|--- Last restart
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
3-11
administration.fm
Administration
Password
3.8
Password
The passwords for user and administrator can be set here. They have to be confirmed after
entering. The factory setting is "123456"; it is highly recommended to change the password after the first login.
Local Phone Menu
|---
Admin
|--- Password
|--- Admin
|--- Confirm admin
|--- User
|--- Confirm user
3.9
Factory Reset
This function resets all parameters to their factory settings. You have to enter the reset password "124816". All personal settings will be erased.
Local Phone Menu
|---
Admin
|--- Maintenance
|--- Factory reset
|--- Reset phone
3.10
Restart Phone
This function initiates a restart of the phone. All personal settings will remain.
Local Phone Menu
|
--- Admin
|
--- Maintenance
|
--- Restart
|
--- Restart phone
3-12
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
beispiele.fm
Examples and HowTos
Canonical Dialing
4
Examples and HowTos
4.1
Canonical Dialing
4.1.1
Canonical Dialing Settings
The following example shows settings suitable for the conversion of given dial strings to canonical format.
Parameter
Example value Explanation
Local country code
44
International country code for the UK.
National prefix digit
0
Used in front of national codes when dialled
without international prefix.
Local national code
115
Area code within the UK (here: Nottingham).
Min local num length
7
Number of digits in a local PSTN number (e.g.
3335333 = 7 digits).
Local enterprise node
780
Prefix to access Nottingham numbers from
within the Siemens network.
PSTN access code
9
Prefix to make an international call in the UK.
Operator code
0, 7800
Set of numbers to access the local operators.
Emergency number
999, 555
Set of numbers to access emergency services.
Initial extn. digits
2, 3, 4, 5, 6, 8
1st digits of numbers that are used for extension numbers on the local node.
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
4-1
beispiele.fm
Examples and HowTos
Canonical Dialing
4.1.2
Canonical Dial Lookup
The following example shows settings suitable for recognizing incoming numbers and assigning them to entries in the local phone book, and for generating correct dial strings from phone
book entries, depending on whether the number is internal or external
Parameter
Example value Explanation
Local code 1
780
Enterprise node prefix (here: Nottingham).
International code 1
+44115943
Equivalent prefix to access numbers on this
node from the PSTN. Here, the prefix used by
the PSTN (DID/DDI: direct inward dialing) is
943, which differs from the enterprise node
prefix used within the enterprise network.
Local code 2
722
Enterprise node prefix (here: Munich).
International code 2
+4989722
Equivalent prefix to access numbers on this
node from the PSTN. Here, the prefix used by
the PSTN for direct inward dialing is identical
to the the enterprise node prefix.
4-2
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
beispiele.fm
Examples and HowTos
Transferring Phone Software and Media Files
4.2
Transferring Phone Software and Media Files
4.2.1
Phone Software
The firmware for OpenStage 15 / 20 T / 30 T / 40 T / 60 T / 80 T can be installed via HiPathManager SW-transfer at HiPath 3000 and via TSDM at HiPath 4000. For OpenStage 60 T/80
T, it is also possible to install the software via USB stick. The required procedure is described
in this section.
4.2.1.1
Installation Using a USB Memory Stick (OpenStage 60 T/80 T)
Please note that some USB memory sticks will not be indentified as an USB memory stick by
the phone. In such a case, please try another stick type or manufacturer.
Advisable and tested USB memory sticks are:
Description
Vendor
Vendor product
number
EAN
Vendor ID Product ID
Kingston DataTraveler Kingston DTI/1GB
USB2.0 1GB
074061708610 0951
2
1603
Kingston DataTraveler Kingston DTI/2GB
USB2.0 2GB
074061709018 13FE
5
1D00
Corsair Flash Voyager Corsair
USB2.0 4GB
CMFSUB2.04GB
087058400652 090C
7
1000
PNY Outdoor Attaché PNY
USB2.0 1GB
P-FD1GBOUTBX
353640150673 13FE
7
1A00
To install the software, take the following steps:
1.
Ensure that the memory stick should contains no other files.
1.
Copy the official SW bind (OS_HI_TDM_<version number>.bin) and the file
prepare.img to the root of the USB stick.
2.
Remove the USB stick from the PC.
3.
Power off the phone.
4.
Connect the USB stick with the USB master port of the phone. Depending on the geometry
of you USB stick, you might need a standard USB extension cable to connect the stick with
the phone.
5.
Power on the phone. If the phone detects the USB stick correctly, you will see the following
output on the LCD:
SLBL: 1.1.0_0013_hs
BOOT:1.3.1_0013_hs_nand128
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
4-3
beispiele.fm
Examples and HowTos
Transferring Phone Software and Media Files
AUX power detected
USB mass storage device detected
Enter update code: _
6.
Enter the update code "0167" using the FPKs. The FPKs are counted from top to bottom:
the topmost FPK represents "0", the lowermost FPK represents "7".
0
1
2
3
4
5
6
7
>
If you do not press any FPK or enter a wrong code, the phone will continue booting the phone application.
7.
If the correct FPK sequence is entered, the USB update starts. The update progress can
be observed on the display.
8.
The update progress is finished when you see the following text:
Update script succedded.
Copy logs to USB stick … done.
Unmounting USB device and exit
Please remove USB device to reboot!
The update process has copied some log files to the USB stick. You will find them in the
log-directory on the stick.
9.
Disconnect the USB stick from the phone. If the update has been successful, the phone
will do an automatic restart. It will start up with the new software bind.
4-4
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
beispiele.fm
Examples and HowTos
Transferring Phone Software and Media Files
4.2.2
Media Files
The following Media files can be transferred to the OpenStage 60 T/80 T via the
OpenStage Manager. For detailed description refer to the corresponding manual.
4.2.2.1
Picture Clips
>
Picture clips are available only on OpenStage 60/80 phones.
Picture Clips are small images used for displaying a picture of a person that is calling on a line.
The supported file formats for picture clips are JPG and PNG.
4.2.2.2
Screensaver
The screensaver is displayed when the phone is in idle mode. It performs a slide show consisting of images which can be uploaded using the web interface.
>
Screensavers are available only on OpenStage 60/80 phones.
For screensaver images, the following specifications are valid:
•
Data format: JPG or PNG. JPG is recommended.
•
Screen format: 4:3. The images are resized to fit in the screen, so that images with a width/
height ratio differing from 4:3 will appear with deviant proportions.
•
Resolution: The phone’s screen resolution is the best choice for image resolution: 320x240
4.2.2.3
Ringer File
>
The download of ringer files is possible only for OpenStage 60/80. This can be
handled by the OpenStage Manager.
Custom Ringtones can be uploaded to the phone. The following file formats are supported:
•
WAV format. The recommended specifications are:
•
•
Audio format: PCM
•
Bitrate: 16 kB/sec
•
Sampling rate: 8 kHz
•
Quantization level: 16 bit
MIDI format.
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
4-5
beispiele.fm
Examples and HowTos
Transferring Phone Software and Media Files
•
4-6
MP3 format. OpenStage 60 T/80 T phones are able to play MP3 files from 32 kbit/s up to
320 kbit/s. As the memory for user data is limited to 8 MB, a constant bitrate of 48 kbit/sec
to 112 kbit/s and a length of max. 1 minute is recommended. Although the phone software
can play stereo files, mono files are recommended, as the phone has only 1 loudspeaker.
See the following table for estimated file size (mono files):
Length
64 kbit/s
80 kbit/s
96 kbit/s
112 kbit/s
0:15 min
0,12 MB
0,15 MB
0,18 MB
0,21 MB
0:30 min
0,23 MB
0,29 MB
0,35 MB
0,41 MB
0:45 min
0,35 MB
0,44 MB
0,53 MB
0,62 MB
1:00 min
0,47 MB
0,59 MB
0,70 MB
0,82 MB
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
beispiele.fm
Examples and HowTos
optiPoint Compatible Mode (V2R0)
4.3
optiPoint Compatible Mode (V2R0)
Some older versions of HiPath 3000 will not identify OpenStage TDM phones correctly. To
overcome this restriction, OpenStage 10 T / 15 T / 30 T phones with firmware from V2R1 onwards can be switched to an optiPoint500 compatible mode. In optiPoint mode, the phone
changes its Phone-ID to that of a corresponding optiPoint model, e. g. an OpenStage 10 T will
adopt the Phone-ID of an optiPoint500 Entry. For a complete reference, see the following table:
OpenStage 10 T
<->
optiPoint500 Entry
OpenStage 15
<->
optiPoint 500 Standard
OpenStage 30
<->
optiPoint500 Advance
4.3.1
Switching Procedure for OpenStage 15 / 30
1.
Press the menu button N for at least 5 seconds.
2.
The menu LED starts flashing and the phone mode selection menu is shown on the display. The currently active phone mode is marked.
Phone Operating Mode:
[*] OpenStage
3.
When pressing the up m or down l key, the second, currently inactive, mode is shown.
Phone Operating Mode:
[ ] OptiPoint
4.
Save and Restart
f
Press the i key again to confirm the selection and activate optiPoint mode.
OptiPoint Operating Mode
Saved successfully!
6.
f
Press the i key to select the optiPoint mode.
OptiPoint Operating Mode
5.
f
f
After 5 seconds the phone performs a restart and comes up in the new operating mode.
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
4-7
beispiele.fm
Examples and HowTos
optiPoint Compatible Mode (V2R0)
4.3.2
Switching Procedure for OpenStage 10
The operating mode of an OpenStage 10 phone is changed via the 3 function keys.
1.
Initially, all 3 LEDs of the function keys are off. Press the rightmost function key for at least
5 seconds.
S
2.
S
S
The current active phone operating mode will be indicated by the LED on one of the other
two function keys. When OpenStage mode is active, the middle LED glows, whereas in
optiPoint mode, the leftmost LED glows.
OpenStage Mode:
S
R
S
optiPoint Mode:
R
3.
S
S
To toggle between modes, press either the leftmost or the middle function key, depending
on which mode is active.
From OpenStage mode to optiPoint mode:
S
R
S
From optiPoint mode to OpenStage mode:
R
4.
4-8
S
S
After a timeout of 2 seconds, the phone restarts and comes up in the new operating mode.
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
beispiele.fm
Examples and HowTos
optiPoint Compatible Mode (V2R0)
4.3.3
Key Mapping in optiPoint Mode (HiPath 3000)
In optiPoint mode, the function keys of OpenStage T phones are defined by the HiPath 3000
system in a specific manner. For Hipath 4000, the assigment of key numbers and functions
must be solved by corresponding AMO TAPRO settings.
>
When migrating from optiPoint to OpenStage, please inform the user about the new
key layout. If desired, the key layout can be changed via the HiPath 3000 system to
adapt to the user’s needs. Depending on the model type, the number of available
free programmable keys may have decreased.
The following figures contrast the key layouts of optiPoint phones to the corresponding OpenStage phones in optiPoint mode, provided that the HiPath 3000 system is in default configuration.
Those keys whose functions are not indicated by symbols like, e. g., H, are labelled. Those
optiPoint keys which will not be available on the corresponding OpenStage phone are shaded.
4.3.3.1
optiPoint 500 Entry / OpenStage 10
Consultation
Redial
Consultation
Redial
Mailbox
Mailbox
Loudspeaker
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
4-9
beispiele.fm
Examples and HowTos
optiPoint Compatible Mode (V2R0)
4.3.3.2
optiPoint 500 Standard / OpenStage 15
Service
FPK 1
Service
Redial
FPK 2
Mute
Servic
Loudspeaker
Service
FPK 3
FPK 4
FPK 5
FPK 6
FPK 7
FPK 8 Release
4-10
Service
Redial
FPK 1
FPK 2
1
FPK 3
1
FPK 4
1
FPK 5
1
FPK 6
1
FPK 7
1
FPK 8
1 Release
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
beispiele.fm
Examples and HowTos
optiPoint Compatible Mode (V2R0)
4.3.3.3
optiPoint 500 Advance / OpenStage 30
On the optiPoint 500 Advance, 2 keys correspond to the 2 upper keys on the OpenStage 30
key module. These are labeled "KM 1" and "KM 2".
The 3 keys labeled "FPK u" on the optiPoint 500 Advance correspond to the keys with the forward r, headset o, and message O symbol on the OpenStage 30. The keys are not programmed in the default configuration, but can be programmed by the user.
Service
Redial
Mute
Servic
Loudspeaker
Service
FPK 1
FPK 2
1
FPK 3
1
FPK 4
1
FPK 5
1
FPK 6
1
1
FPK 7
FPK 8
1
FPK11
KM
FPK21
KM
FPK u
1
FPK u
1
FPK u
1
FPK u
1
Mute
Servic
Service
FPK 1
FPK 2
1
FPK 3
1
FPK 4
1
FPK 5
1
FPK 6
1
FPK 7
1
FPK 8
1
FPK Release
1
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
4-11
beispiele.fm
Examples and HowTos
optiPoint Compatible Mode (V2R0)
4-12
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
referenz.fm
Local Phone Menu
5
|---
Local Phone Menu
Admin
|--- Network
| |--- IP configuration
|
|--- System
| |--- Features
|--- Configuration
|
|
|--- General
|
|
|
|
|--- Bluetooth
|
|
|--- Local functions
| |--- Locality
| | |--- Canonical settings
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |--- Canonical lookup
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |--- Canonical dial
| |
| |
| |
| |
| |
| |--- Pixel saver
|
|
|
|
Network - IP configuration
IP address
-> Section 3.2
Features - configuration
Not used timeout
-> Section 3.3
Bluetooth admin settings
Local device address
-> Section 3.4
Canonical settings
Local country code
National prefix digit
Local national code
Min local num length
Local enterprise node
PSTN access code
International access code
Operator code
Emergency number
Initial extn. digits
-> Section 3.5.1
Canonical lookup
Local code 1
International code 1
Local code 2
International code 2
Local code 3
International code 3
Local code 4
International code 4
Local code 5
International code 5
-> Section 3.5.2
Canonical dial
Internal numbers
External numbers
External access code
International gateway
-> Section 3.5.1
Pixel saver
Timeout (Hrs)
-> Section 3.6
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
5-1
referenz.fm
Local Phone Menu
|--- General information
|
|
|--- Password
|
|
|
|
|--- Maintenance
|--- Factory reset
|
|
|
--- Restart
5-2
General information
Software ver.
Last restart
Admin password
Admin
Confirm admin
User
Confirm user
-> Section 3.7
-> Section 3.8
Please enter admin password -> Section 3.9
Reset phone
Enter admin password
Restart phone
-> Section 3.10
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
OperaAdminSIX.fm
Index
Nur für den internen Gebrauch
Index
Z
Zahlen
G
3-way Navigator 1-6
5-way Navigator 1-4
Graphics display 1-3
A
Handset 1-3, 1-4, 1-5, 1-6, 1-7, 1-8
Headset 1-3
HiPath Communication System 1-9, 4-3
Admin password
set timeout 3-5
Administration 1-9
Administration Menu (Local Menu) 3-1, 3-2
Always add node 3-7
Audio Keys 1-3, 1-4, 1-5, 1-6, 1-7, 1-8
B
Bluetooth adapter 3-5
C
Call Display 1-4
Call display 1-3
Canonical Dial 3-7
Canonical Dial Lookup 3-9, 4-2
Canonical Dialing Settings 3-6, 4-1
D
Display 1-4, 1-5, 1-6, 1-7
E
Emergency number 3-7
External access code 3-8
External numbers 3-8
F
Factory Reset 3-12
For external numbers 3-8
FPK 1-3, 1-4, 1-5, 1-7, 1-8
Free programmable sensor keys 1-3, 1-4, 15, 1-7, 1-8
Function keys 1-3, 1-4, 1-5, 1-6
H
I
Initial extn. digits 3-7
Internal numbers 3-7
International access code 3-7
International code 1 ... 5 3-10
International form 3-8
International gateway 3-8
IP Address 3-5
J
JPG 4-5
K
Keypad 1-3
keypad 1-4, 1-5, 1-6, 1-7, 1-8
L
Last restart 3-11
Leave as + 3-8
Local 5-1
Local Area Code 3-6
Local code 1 ... 5 3-10
Local country code 3-6
Local enterprise form 3-7
Local enterprise node 3-6
Local Menu 1-9, 5-1
Local national code 3-6
Local public form 3-8
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
Z-1
OperaAdminSIX.fm
Index
Nur für den internen Gebrauch
M
S
Microfon 1-3
MIDI 4-5
Mode keys 1-3
MP3 4-6
Mute 1-3
Screensaver
upload 4-5
Software version 3-11
T
N
National prefix digit 3-6
National public form 3-8
Navigaton keys 1-7
Not required 3-8
O
OpenStage Manager 1-9, 4-5
Operator code 3-7
P
Password, enter 3-1
Phone software
update 4-3
Picture Clips
upload 4-5
Pixel saver
set timeout 3-11
PNG 4-5
Power supply 2-9
PSTN access code 3-6
TouchGuide 1-3
TouchSlider 1-3
Trunk Prefix 3-6
U
Update Phone Software
USB memory stick 4-3
Upload
picture clips 4-5
ringer file 4-5
screensaver 4-5
USB adapter cable 2-8
USB memory stick 2-8, 4-3
Use external numbers 3-7
Use national code 3-8
User password
restore 3-12
set timeout 3-5
W
WAV 4-5
R
Reset password 3-12
Restart Phone 3-12
Ringer File
upload 4-5
Z-2
A31003-S2000-M101-4-76A9, 2010-02-23
HiPath 3000/5000, HiPath 4000 - OpenStage 10/15/20/40/60/80 T, Administration Manual
Copyright © Siemens Enterprise
Communications GmbH & Co. KG 2009
Hofmannstr. 51, 80200 München
Siemens Enterprise Communications GmbH & Co. KG
is a Trademark Licensee of Siemens AG
Reference No.: A31003-S2000-M101-4-76A9
Communication for the open minded
Siemens Enterprise Communications
www.siemens-enterprise.com
The information provided in this document contains
merely general descriptions or characteristics of
performance which in case of actual use do not
always apply as described or which may change as
a result of further development of the products. An
obligation to provide the respective characteristics
shall only exist if expressly agreed in the terms of
contract. Availability and technical specifications are
subject to change without notice.
OpenScape, OpenStage and HiPath are registered
trademarks of Siemens Enterprise
Communications GmbH & Co. KG.
All other company, brand, product and service
names are trademarks or registered trademarks of
their respective holders.