Bosch APC-AMC2-4WCF Installation manual

AMC2 4W
APC-AMC2-4W | APC-AMC2-4WCF | APC-AMC2-4WUS
en
Installation manual
AMC2 4W | Installation manual
| en 3
Remarks
This hardware is part of a security system. Access shall be limited to authorized persons only.
Some states do not allow the exclusion or limitation of implied
warranties, or limitation of liability for incidental or consequential damages, so the above limitation or exclusion might not
apply to you.
Bosch Security Systems retains all rights not expressly granted.
Nothing in this license constitutes a waiver of Bosch’s rights
under the U.S. Copyright laws or any other federal or state law.
If you have any questions concerning this license, please, write
to:
Bosch Access Systems GmbH
Adenauerstr. 20 / A3
D-52146 Würselen
Germany.
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
4
en | Table of Contents
AMC2 4W | Installation manual
Table of Contents
1
1.1
1.2
1.3
Please read carefully7
Explanation of Used Symbols7
Internet7
We Are Interested in Your Opinion8
2
2.1
2.2
2.3
2.4
Safety Instructions9
Important Safety Notes9
FCC & ICES Information12
Safety Precautions13
Unpacking14
3
3.1
3.2
3.3
3.4
Introduction15
Description of the AMC2 4W 15
Equipment Configuration17
Performance Characteristics20
System Overview21
4
Technical Data22
5
5.1
5.2
5.3
5.4
5.5
5.6
5.6.1
5.6.2
5.6.3
5.7
5.8
5.9
5.10
5.11
5.12
5.13
Installing26
Mounting26
Demounting27
Opening the AMC2 4W Case28
Cabling28
Connecting Power Supply31
RS-485 Host Interface33
RS-485 Two Wire Connection35
RS-485 Four Wire Connection36
DIL Switch Address Selector37
RS-232 Host Interface39
Ethernet Interface41
RS-485 Extension Module Bus42
Wiegand Interface for Card Readers43
Connecting Relay Outputs44
Connecting Analog Input Devices47
Tamper Protection49
6
6.1
6.2
6.3
Operating50
Status Display of the AMC2 4W50
Configuring the Ethernet Interface52
Resetting the AMC2 4W52
7
7.1
Appendix54
Connecting Diagrams54
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
7.2
Legend58
8
Index59
Bosch Sicherheitssysteme GmbH
Table of Contents | en 5
F.01U.024.965 | V 0.1 | 2006.03
6
en | Table of Contents
F.01U.024.965 | V 0.1 | 2006.03
AMC2 4W | Installation manual
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
Please read carefully | en 7
1
Please read carefully
1.1
Explanation of Used Symbols
Throughout this document, helpful tips, important notes, cautions and warnings will be presented for the reader to keep in
mind. These appear different from the rest of the text as follows:
CAUTION! or WARNING!
These warn the operator that damage to the program or equipment might occur.
NOTE!
i
Important Notes – must be followed for successful operation
and programming. Tips and shortcuts might also be included
here.
1.2
Internet
If you are interested in further information on this product or
information on other products, please, refer to our website at
http://www.bosch-security-systems.com.
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
8
en | Please read carefully
1.3
AMC2 4W | Installation manual
We Are Interested in Your Opinion
We constantly try to improve the quality of our products and
our manuals. Should you have any suggestions for improvement, please, send us your comments.
Bosch Security Systems
Adenauerstr. 20 / A3
D-52146 Würselen
Germany
Tel.:+49 24 05 / 60 05-0
Fax:+49 24 05 / 60 05-29
Email:info.service@de.bosch.com
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
2
Safety Instructions
2.1
Important Safety Notes
1.
Safety Instructions | en 9
Read, Follow, and Retain Instructions - All safety and
operating instructions must be read and followed properly
before putting the unit into operation. Retain instructions
for future reference.
2.
Consider all Warnings - Adhere to all warnings on the unit
and in the operating instructions.
3.
Accessories - Use only accessories recommended by the
manufacturer or those sold with the product. Accessories
not recommended by the manufacturer shall not be used,
as they may cause hazards.
4.
Installation Precautions - Do not place this unit on an
unstable stand, tripod, bracket, or mount. The unit may
fall, causing serious injury to persons and damage to the
unit. Mount the unit according to the manufacturer’s
instructions.
5.
Cleaning - Disconnect the unit from power before cleaning.
Follow any instructions provided with the unit. Generally,
using a damp cloth for cleaning is sufficient. Do not use liquid cleaners or aerosol cleaners.
6.
Service - Do not attempt to service this unit by yourself.
Opening or removing covers may expose you to dangerous
voltages or other hazards. Refer all servicing to qualified
service personnel.
7.
Damage Requiring Service - Disconnect the unit from the
main AC or DC power source and refer servicing to qualified service personnel under the following conditions:
•
•
When the power supply cord or plug is damaged.
If liquid has been spilled or an object has fallen into
the unit.
•
If the unit has been exposed to water and/or inclement weather (rain, snow, etc.).
•
If the unit does not operate normally, when following
the operating instructions. Adjust only those controls
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
10 en | Safety Instructions
AMC2 4W | Installation manual
specified in the operating instructions. Improper
adjustment of other controls may result in damage,
and require extensive work by a qualified technician
to restore the unit to normal operation.
•
•
If the unit has been dropped or the cabinet damaged.
If the unit exhibits a distinct change in performance,
this indicates that service is needed.
8.
Replacement Parts - When replacement parts are
required, the service technician shall use replacement
parts that are specified by the manufacturer. Unauthorized
substitutions may result in fire, electrical shock or other
hazards.
9.
Safety Check - Upon completion of service or repair work
on the unit, ask the service technician to perform safety
checks to ensure that the unit operates properly
10. Power Sources - Operate the unit only from the type of
power source indicated on the label. If unsure of the type
of power supply to use, contact your dealer
•
For units intended to operate from battery power,
refer to the operating instructions.
•
For units intended to operate with External Power
Supplies, use only the recommended approved power
supplies.
•
For units intended to operate with a limited power
source, this power source must comply with EN/UL
60950. Substitutions may damage the unit or cause
fire or shock.
•
For units intended to operate at 12 VDC normal input
voltage is 12 VDC. Voltages applied to the unit’s
power input shall not exceed 15 VDC. User-supplied
wiring, from the 12 VDC power supply to the unit,
must be in compliance with electrical codes (Class 2
power levels). Do not ground the 12 VDC supply at the
terminals or at the unit’s power supply terminals.
11. Grounding - If an outside cable system is connected to the
unit, ensure that the cable system is grounded. U.S.A.
models only Section 810 of the National Electrical Code,
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
Safety Instructions | en 11
ANSI/ NFPA No.70, provides information regarding proper
grounding of the mount and supporting structure, grounding of the coax to a discharge unit, size of grounding conductors, location of discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
12. Grounding and Protection against reverse Polarity - This
unit may be equipped with a polarized alternating current
line plug (a plug with one blade wider than the other). This
safety feature allows the plug to fit into the power outlet in
only one way. If unable to insert the plug fully into the outlet, try reversing the plug. If the plug still fails to fit, contact an electrician to arrange replacement of the obsolete
outlet. Do not defeat the safety purpose of the polarized
plug. Alternately, this unit may be equipped with a 3-wire
grounding plug (a plug with a third pin, for grounding).
This safety feature allows the plug to fit into a grounding
power outlet only. If unable to insert the plug into the outlet, contact an electrician to arrange replacement of the
obsolete outlet. Do not defeat the safety purpose of the
grounding plug.
13. Lightning - For added protection during a lightning storm,
or when this unit is left unused for long periods of time,
disconnect the unit from power. This will prevent damage
to the unit due to lightning and excessive power line
surges.
14. Restricted Access Locations are required for the installation.
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
12 en | Safety Instructions
2.2
AMC2 4W | Installation manual
FCC & ICES Information
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC rules. The limits are designed to provide reasonable protection against harmful interference in a residental installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
1.
2.
Reorient or relocare receiving antenna
Increase the separation between the equipment and the
receiver
3.
Connect the equipment into an outlet on a circuit different
4.
Consult the dealer or an experienced radio/TV technician
from that to which the receiver is connected
for help
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
2.3
Safety Instructions | en 13
Safety Precautions
Read instructions!
Before working with the AMC2 4W, read these instructions
carefully. Make sure you have understood all information
described in this document.
Warning! Risk of electric shock!
External power supplies must be installed and put into service
by qualified personnel. Compliance with the relevant regulations must be ensured.
Warning! Risk of damaging equipment!
•
Always switch off power of the AMC2 4W before modifying the installation.
•
Do not connect or disconnect plug connectors, data
cables or screw connectors while power is on!
Health and Safety
Installation of the AMC2 4W must comply with any local fire,
health and safety regulations. A secured door that may be part
of an escape route from an area must be installed with:
•
A fail-safe lock (A). So that the door will be released if
power fails. Ideally, a magnetic lock should be used as
these are less likely to jam or seize.
•
A normally-closed break-glass or manual pull (B) in the
lock supply wiring, so that in an emergency the failsafe lock can be immediately powered down.
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
14 en | Safety Instructions
AMC2 4W | Installation manual
CAUTION!
You must ground the AMC2 4W. Disconnect both AC and battery power supply before working on the controller.
Warning! Risk of damage!
Protect the hardware from electrostatic discharge by observing
ESD instructions before unpacking or touching connectors or
electronics.
CAUTION: Lithium Battery
Danger of explosion if battery is replaced incorrectly. Replace
only with the same type as recommended by the manufacturer.
Dispose used batteries according to the battery manufacturer’s
instructions.
2.4
Unpacking
Check the packaging for visual damage. If anything has been
damaged during transport, make the transport agency aware of
this.
Carefully unpack the unit. This is an electronic device that must
be handled with care to avoid damage. Do not attempt to put
the unit into operation if components are damaged.
If parts are missing, inform your customer service representative or a Bosch Security Systems salesperson. The shipping carton is the safest transport container for the unit. Store it and
the other packaging material for future use. If the unit has to be
sent back, use the original packaging.
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
Introduction | en 15
3
Introduction
3.1
Description of the AMC2 4W
The AMC2 4W is equipped with four independent interfaces for
Wiegand type readers. By that it is able to control two doors
with a reader in each direction and up to four doors with a
reader in one direction only.
Fig. 3.1
The Access Modular Controller AMC2 4W
All necessary information for access verification is stored in a
battery buffered on-board memory and a Compact Flash (CF)
memory card. This guarantees autonomous access decisions
and complete access registrations even if the management host
system is offline. The built in compact flash adapter provides
adequate storage capability for cardholders and events.
The AMC2 4W electronic is completely covered by a plastic
housing. The LC Display provides all important status information.
Using the AMC2 4W gives you the full functionality and the
offline capability of a complete access control system on each
room. This leads to an excellent reliability and a very high
redundancy without paying extra money.
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
16 en | Introduction
Fig. 3.2
AMC2 4W | Installation manual
The AMC2 4W in a four door safety lock
The AMC2 4W can communicate upstream to the host computer
via eight RS-485 multi-dropped, RS-232 or 10/100 Mbit/s Ethernet. It has eight analog input devices and eight relay outputs.
With its analog input devices, the AMC2 4W verifies, for example, if a lock is closed or open. The relay outputs can be used to
activate lock mechanisms if access is granted, or activate an
external alarm system if an intrusion or system alert is
detected. If the eight input and output on board are not enough
to configure the system up to three additional extensions (AMC
8I-8O or AMC 16I-16O) can be connected. The extensions offer
8 or 16 additional inputs and outputs.
The setup procedure for an AMC2 4W is very simple and
extremely fast by the use of door templates. Once selected, all
the inputs and outputs are predefined. This settings can be
changed using the Device Editor in that way to choose every
free contact of the AMC2 4W or an connected extension.
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
3.2
Introduction | en 17
Equipment Configuration
Fig. 3.3
1.
2.
Upper circuit board with display (top side)
Internal tamper contact
DIP switch for RS-485 address selection, protocol and RS232/RS-485 selection
3.
Lithium battery for buffering of static RAM and real time
clock (RTC). The battery shall be replaced by qualified personnel every ten years or if indicated by an appropriate
event.
4.
Reset push button - available by using the srew driver
5.
LC Display
6.
Push button to select the display view - available by using
the push button on the top of the housing
7.
Jumper: Potential equalization between different mass systems and protective earth (shield)
8.
Jumper: interface selector RS-485 Host connection, RS485 two wire or RS-485 four wire (depends on external
wiring)
9.
Configurable RS-485 host interface (pluggable screw connector)
10. Docking station for the compact flash
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
18 en | Introduction
AMC2 4W | Installation manual
11. Configurable RS-232 host interface (ribbon cable connector)
12. Configurable 10/100 Mbit/s Ethernet interface
Fig. 3.4
Overview - Interfaces
13. RS-485 extension module bus (Pluggable screw connector)
14. External tamper contact (Pluggable screw connector)
15. Power supply (Pluggable screw connector)
16. Wiegand interface for card readers (Pluggable screw connector)
17. Analog input (Pluggable screw connector)
18. Relay Output (Pluggable screw connector)
I-IV Channel 1 - 4
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
Fig. 3.5
Introduction | en 19
Jumper at the bottom side
19. Jumper: Selector for either potential free relay output or
powered by AMC2 4W internal power supply (wet/dry contacts)
20. Jumper: Potential equalization between different mass
systems and protective earth (shield)
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
20 en | Introduction
3.3
AMC2 4W | Installation manual
Performance Characteristics
•
•
Host address selectable via DIP sliding switch
Four possible configurable host interfaces:
•
•
•
•
•
•
RS-485 4-wire
RS-232
Ethernet 10/100 Mbit/s
Four peripheral input devices via Wiegand interface
Eight relay outputs
•
•
•
•
•
•
•
•
•
RS-485 2-wire
potential-free or
with internal power supply
Eight analog inputs with internal power supply
Battery buffered SRAM and real time clock (RTC)
Pluggable Compact Flash from 64 MB to 1024 MB
LC Display
Transfer rate host interface RS-485: 38,4 kBit/s
Self controlling transfer-receive-switching
Power supply for internal electronics: 10V - 30VDC - max.
7A
•
The AMC2 4W is to be used with power supply AMC PBC60 (F.01U.026.573) with integrated UPS
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
3.4
Introduction | en 21
System Overview
The Access Controller AMC2 4W is connected between the
management host system and different peripheral devices. By
default a management host system is connected via Ethernet. A
management host connection via RS-485 or RS-232 is also possible.
Fig. 3.6
System overview
In RS-485 mode up to eight access controllers AMC2 4W can be
combined on one party line. Via Wiegand interfaces up to four
peripheral devices can be connected to each AMC2 4W.
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
22 en | Technical Data
4
AMC2 4W | Installation manual
Technical Data
Hardware
–
Integrated Microcontroller (32Bit,
–
SRAM (2MB)
–
Serial EEPROM
30MHz)
–
RTC
–
Pluggable Compact Flash from 64 MB
–
Battery for SRAM and real time clock
–
Host address selectable via DIP sliding
up to 1024 MB
(RTC)
switch or software
–
Host interface
•
RS-485 2-wire or 4-wire
Transfer rate: 38,4 kBit/s
(No parity, 8 Bit, 1 Stopbit)
•
•
–
RS-232
Ethernet
four Wiegand interfaces for card readers
–
Eight relay outputs
•
•
Maximum switching power: 60VA
Maximum switching voltage: 30V
AC/DC
•
–
Maximum switching current: 2A
eight analog inputs with sabotage monitoring
–
Tamper contact for enclosures
Power supply
Electronics: 10V – 30V DC
Display
64,8 mm x 13,9 mm
1 line, 16 characters
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
Technical Data | en 23
Power con-
Internal: 5 VA
sumption
Peripheral devices:
using the AMC PBC-60
•
•
•
up to 55 VA at 12V DC
constant load: 25 VA
peak load: 30 VA
Connectors
Pluggable screw connectors
Protection
IP30
Class
Environment
0°C to 45°C
temperature
Humidity
Up to 95%, without condensation
Housing mate-
Bottom: PPO (UL 94 V-0)
rial
Top: Polycarbonate (UL 94 V-0)
Dimensions
(W/H/D) 225mm x 88mm x 60mm (8.9" x
3.5" x 2.4")
Weight: app. 0,48 kg (0.9 pounds)
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
24 en | Technical Data
AMC2 4W | Installation manual
Conductor
For short distances below 25m (75 feet)
data for con-
use AWG18 conductors. For higher dis-
nection to
tances install an additional power supply
power supply
close to the AMC2 4W.
Please, calculate the voltage drop by checking the conductor specifications for characteristic resistance values. The voltage drop
shall not exceed 2V.
Example:
Length = 50m/165 ft
U = 12V, I = 2A, maximum VDrop = 2V
6,385
i.e. RAWG18 (acc. specs) =
Ω
1000 ft
or
Ω
20,948 km
Ω
⋅ 0,05km ⋅ 2 A
= 2.1V
VDrop = 20,948 km
6,385
VDrop =
Ω
⋅ 165 ft ⋅ 2 A
1000 ft
= 2.1V
Critical condition! Install the power supply
closer to the controller.
Conductor
Use AWG18 conductors.
data
Please, calculate your voltage drop (see
relay outputs
above) by checking conductor specifications for characteristic resistance values.
Conductor
Use AWG22 conductors.
data analog
Please, calculate your voltage drop (see
input
above) by checking conductor specifications for characteristic resistance values.
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
Technical Data | en 25
Conductor
Use AWG22 conductors.
data RS-485
Please, calculate your voltage drop (see
slave
above) by checking conductor specifications for characteristic resistance values.
CAUTION!
The voltage drop at the different cables add up! Their sum shall
be less than 2V!
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
26 en | Installing
AMC2 4W | Installation manual
5
Installing
5.1
Mounting
The AMC2 4W can be attached on a standard 35 mm mounting
rail via a snap-in mechanism. Attach the AMC-4W into the upper
edge of the mounting rail, then push down the AMC2 4W and
snap it onto the rail by pushing it towards the back.
Fig. 5.1
Mounting the AMC2 4W on a mounting rail
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
5.2
Installing | en 27
Demounting
NOTE!
i
To remove the AMC2 4W from a mounting rail, first, remove all
pluggable screw connectors.
Push down the AMC2 4W until it snaps out of the mounting rail.
Pull the lower end of the AMC2 4W from the mounting rail.
Fig. 5.2
Demounting the AMC2 4W from a mounting rail
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
28 en | Installing
5.3
AMC2 4W | Installation manual
Opening the AMC2 4W Case
NOTE!
i
To open the AMC2 4W, first, remove all pluggable screw connectors at least the host connection.
The AMC2 4W case consists of a top cover mounted with a twopoint snap-in closure on a ground chassis. To open the
AMC2 4W push down the two snap-ins with a srew driver. After
that the cover can be moved to bottom.
Fig. 5.3
5.4
Opening the AMC2 4W case
Cabling
CAUTION!
The cables used in the AMC2 4W access control system are not
prone to electrical interference. However, you should avoid
routing cables close to heavy load switching cables and equipment. If this is unavoidable, cross the cable at right angles every
1 to 2 m (3 to 6 ft) to reduce interference.
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
Installing | en 29
Grounding and Shielding
All components of the access control system must be
grounded. The grounding points shall then be connected to an
earth ground point. This insures that all components are properly protected against shock hazard.
It is good practice to shield all wires carrying low level signals.
You should connect only one end of the shield, preferably the
source end. Connecting both ends of a shield will result in
ground loops. It is recommended that the unconnected end of
the shield be insulated to prevent accidental connection.
The AMC2 4W enables you to set up a central ground or shielding point, simply by setting a couple of jumpers. Set these
jumpers only if ground or shield is not connected otherwise.
WARNING!
Risk of damaging equipment!
When using multiple AMC2 4W devices, set the ground main
jumper only once to assure a central point star connection.
Fig. 5.4
Location of ground jumper RS-485 host interface
The jumper setting A1 shows the delivery status.
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
30 en | Installing
AMC2 4W | Installation manual
Setting jumper JP1 connects the internal ground of the AMC2
4W to the ground of the RS-485 host interface. If the ground
conductor of the RS-485 interface between the AMC2 4W modules is connected, set Jumper JP2 only at a single AMC2 4W.
The host system must not connect cable shield and protective
ground. If not using the ground conductor of the RS-485 host
interface, Jumper JP1 should be set at every AMC2 4W.
Setting jumper JP2 connects the internal ground of the AMC2
4W to the shield of the RS-485 host interface. Set Jumper JP2
only at the first AMC2 4W of a party line. The host system must
not connect cable shield and protective ground. If the AMC2 4W
is set to RS-232 mode, Jumper JP2 must be set.
Fig. 5.5
Location of ground jumper bottom side
Jumper B connects the internal ground of the AMC2 4W to the
RS-485 ground of the slave interface. Jumper B shall only be
set (B2) if the AMC2 4W powers all other peripheral devices
which are directly connected to the AMC2 4W.
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
5.5
Installing | en 31
Connecting Power Supply
Connect the power supply to the 7-pin pluggable screw connector labeled with POWER on the upper case.
NOTE!
i
A complete connection diagram is shown in chapter
Section 7.1 Connecting Diagrams of this documentation.
Fig. 5.6
Location of the power supply connector
An external power supply (10 - 30V DC) must be connected for
internal electronics at pin 1 (positive) and pin 3 (negative) of
the pluggable screw connector.
An additional power supply (12V DC) for peripheral devices (i.e.
card readers and door openers) must be connected at pin 6
(positive) and pin 7 (negative).
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
32 en | Installing
AMC2 4W | Installation manual
WARNING!
Risk of Damage!
Power supply for external devices is 12V DC only! Applying
higher voltages may cause hazards to people and damage to the
equipment.
When using a shared 12 VDC power supply for internal electronics and peripherals, pin 1 and pin 6 resp. pin 3 and pin 7 can be
shortened.
If an uninterruptible power supply (UPS) is used, the relay output for power good signals from the UPS is connected to the
following pins:
•
•
•
pin 4 and 7 for power good AC
pin 5 and 7 for power good Battery
pin 6 and 7 for power good DC
Otherwise these pins must be short-circuited.
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
5.6
Installing | en 33
RS-485 Host Interface
An RS-485 host system can consist of up to eight AMC2 4W controllers connected via 2- or 4-wire connection.
Fig. 5.7
Configuration of a RS-485 host system
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
34 en | Installing
AMC2 4W | Installation manual
The following conditions apply for an RS-485 bus system:
•
A bus system consists of a bus line and/or one or more
branch lines.
•
Cable lengths exceeding 100m or 300ft must be installed
as bus lines.
•
Branch lines are branching connections from a bus line. If a
branch line is used. the spur line should be attached
directly to the device.
•
•
Bus devices are the host computer.
Peripheral devices are AMC2 4W which are connected to
the host computer.
•
Maximum cable length of a bus line must not exceed
1200m or 4000ft.
•
The cable length of branch lines must not exceed 100m or
300ft.
•
Any bus line conductor connects up to eight AMC2 4W. The
maximum number of devices must not be exceeded.
•
For longer bus lines connect the AMC2 4W to multiple
AMC-MUX (-EXT) with the host.
To use RS-485 mode at the AMC2 4W, connect the data cables
to the pluggable screw connector of the RS-485 host interface.
Then set the RS-485 address via DIP switch or software and
activate the RS-485 two-wire or four-wire mode via jumper settings.
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
Fig. 5.8
5.6.1
Installing | en 35
RS-485 host interface
RS-485 Two Wire Connection
Fig. 5.9
Fig. 5.10
Connection scheme of a RS-485 two wire connection
Settings for RS-485 two wire connections
NOTE!
i
A complete connection diagram of the RS-485 host interface is
shown in chapter Section 7.1 Connecting Diagrams of this documentation.
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
36 en | Installing
5.6.2
AMC2 4W | Installation manual
RS-485 Four Wire Connection
Fig. 5.11 Connection scheme of an RS-485 four wire connection
Fig. 5.12 Settings for RS-485 four wire connection
NOTE!
i
A complete connection diagram of the RS-485 host interface is
shown in chapter Section 7.1 Connecting Diagrams of this documentation.
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
5.6.3
Installing | en 37
DIL Switch Address Selector
The first four DIL switches for address selection define the RS485 address of the AMC2 4W in a RS-485 bus system. Switch 5
selects on of the two different protocols, SDEB and BPA
(according to DIN6619). Switch 6 sets the connection to the
host system to either RS-232 or RS-485.
NOTE!
Using Ethernet connection it is recommended to set switch 1 to
i
ON (= delivery status)
Using RS-232 connection the address must be set, which is configured in the Device Editor. Therefore this is a point-to-point
connection the usually configured address will be 1 - so the
switch 1 must be also set to ON.
Fig. 5.13
Location of the RS-485 address selector
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
38 en | Installing
AMC2 4W | Installation manual
Address
none
1
2
3
4
5
6
7
8
1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
DIP Switches
2
3
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
Table 5.1 Setting the RS-485 address with the DIP swich
Mode
ON
OFF
DIP Switches
5
6
SDEB
RS-232
BPA
RS-485
Table 5.2 Protocol and connection settings
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
5.7
Installing | en 39
RS-232 Host Interface
The AMC2 4W offers an RS-232 serial interface to connect a
host computer or serial modem.
CAUTION!
Cable length between two RS-232 COM serial interfaces must
not exceed 15 meters (45 ft).
Fig. 5.14
Location of the RS-232 serial interface
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
40 en | Installing
AMC2 4W | Installation manual
Fig. 5.15 Connection scheme of the RS-232 interface
NOTE!
i
A complete connection diagram of the RS-232 host interface is
shown in chapter Section 7.1 Connecting Diagrams of this documentation.
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
5.8
Installing | en 41
Ethernet Interface
The AMC2 4W offers an additional 10/100 Mbit/s Ethernet autosensing interface to connect to a local area network or host
computer.
CAUTION!
Use either a CAT5 crossover cable to connect the AMC2 4W
directly to a computer’s network interface or a standard CAT5
patch cable to connect the AMC2 4W to a network hub or network switch.
Fig. 5.16
Location of the Ethernet interface
NOTE!
i
A complete connection diagram of the Ethernet host interface is
shown in chapter Section 7.1 Connecting Diagrams of this documentation.
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
42 en | Installing
5.9
AMC2 4W | Installation manual
RS-485 Extension Module Bus
The RS-485 Extension Module Bus expands the AMC2 4W with
additional I/O modules (AMC 8I-8O or AMC 16I-16O). Up to
three expansion modules can be connected to provide additional in- and outputs, for example, for elevator control.
Fig. 5.17 Location of the RS-485 extension module bus
NOTE!
i
A complete connection diagram of the RS-485 extension module bus is shown in chapter Section 7.1 Connecting Diagrams of
this documentation.
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
5.10
Installing | en 43
Wiegand Interface for Card Readers
The AMC2 4W has four Wiegand interfaces to integrate up to
four card readers with Wiegand compatible interfaces. Each
interface is connected via a 10-pin pluggable screw connector
(S2, S7, S14 and S19).
Fig. 5.18
Location of the Wiegand interfaces for external devices
NOTE!
i
A complete connection diagram of the Wiegand interface is
shown in chapter Section 7.1 Connecting Diagrams of this documentation.
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
44 en | Installing
5.11
AMC2 4W | Installation manual
Connecting Relay Outputs
To operate locks or alarm systems the AMC2 4W has eight form
C relay outputs. The outputs will be connected to the 3-pin
pluggable screw connectors: S5, S6, S10, S11, S17, S18, S22,
and S23.
Fig. 5.19 Location of the relay output connectors
Each relay output can operate in ‘wet’ mode, using the AMC2
4W's internal 12V DC power supply for external devices or ‘dry’
mode with potential free contacts for externally powered systems.
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
Fig. 5.20
Installing | en 45
Wet mode and dry mode of the AMC2 4W relay outputs
Maximum switching power of each relay output is 60 VA, maximum switching voltage 30 V DC and maximum switching current 2 A.
Risk of Damage!
Do not connect externally powered devices in wet mode This
can damage the AMC2 4W
Risk of Damage!
Do not exceed switching specifications of the relay. Using
exceeding voltage or current on relay contacts in either mode
can damage the AMC-W.
NOTE!
i
A complete connection diagram of the relay output connectors
is shown in chapter Section 7.1 Connecting Diagrams of this
documentation.
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
46 en | Installing
AMC2 4W | Installation manual
Each relay output has a separate jumper setting on the bottom
side of the lower circuit board to activate wet (D2)or dry (D1)
mode.
Fig. 5.21 Location of relay output jumpers (bottom side)
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
5.12
Installing | en 47
Connecting Analog Input Devices
The AMC2 4W has eight analog inputs, for example, for potential free lock mechanisms or to detect if a lock is closed or
open. The inputs will be connected to the 2-pin pluggable
screw connectors: S3, S4, S8, S9, S15, S16, S20, and S21.
Fig. 5.22
Location of the analog input connectors
The AMC2 4W can also detect the wiring conditions ‘short circuit’ and ‘broken’ and initiate an alarm if the appropriate
devices are connected.
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
48 en | Installing
AMC2 4W | Installation manual
1. Door open:RS + RP
2. Door closed:RS
3. Broken wire:RS + RP =
4. Short circuit:RS + RP = 0
The resistor values can vary and
depend on the used lock system
(wire resistance negligible).
Default values are:
RS = 2,2 k
RP = 4,7 k
Fig. 5.23 Operating modes of a lock using the analog input device
NOTE!
i
A complete connection diagram of the analog input devices is
shown in chapter Section 7.1 Connecting Diagrams of this documentation.
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
5.13
Installing | en 49
Tamper Protection
To protect the AMC2 4W against unauthorized access and prevent the AMC2 4W from tampering with sensitive data, the
AMC2 4W offers an additional interface to connect external
tamper contacts. This interface is a potential-free 2-pin pluggable screw connector marked with T. If not using the tamper
contact, short-circuit the contacts with a wire connection.
Fig. 5.24
Location of the tamper protection contact
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
50 en | Operating
AMC2 4W | Installation manual
6
Operating
6.1
Status Display of the AMC2 4W
The LC Display delivers information about the AMC2 4W status.
Push the 'Dialog' button to switch between different modes.
Fig. 6.1
Location of the ’Dialog’ button
The display mode which has been set remains until the next
operation of the ‘Dialog’ button. The order of the display pages
is determined and follows the scheme shown in the table
below.
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
Push
0
Display (Example)
V37.02 02.03.06
Operating | en 51
Description
Software versions and date of
the downloader
1
99999876543210 A
(= default page)
BOSCH serial number and bus
address
A = address 1
...
2
3
02.06 15:35:15
Dig. IO: ::::::::::::::::
H = address 8
Current date and time
Display of the digital contacts:
setted input signals will be
shown with an extension above output signal with an extension
3a
3b
3c
4
5
6
7
8
below
Dig. I1: ::::::::[::::::::]
If there are I/O-Boards conDig. I2: ::::::::[::::::::] nected the signals will be shown
Dig. I3: ::::::::[::::::::]
on separate pages.
MAC 0010174C8A0C
MAC-address
N AMC-1234-5678
Network name of the AMC
I 192.168.10.18
IP-address of the AMC
H 0.0.0.0
IP-address of the host computer
DHCP 1
DHCP-status:
1 = on
9
10
D 192.168.10.1
Host: +
2 = off
IP-address of the DNS server
Host activity:
+ = online
- = offline
Tabelle 6.1
Display pages
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
52 en | Operating
6.2
AMC2 4W | Installation manual
Configuring the Ethernet Interface
To configure the AMC2 4W in a TCP/IP network environment
use the tool AmcIpConfig provided in the following directory :
\\Runtime-drive:\MgtS\AccessEngine\AC\bin
This tool can be copied and used on every computer.
NOTE!
i
The usage of the software application to configure the AMC2
4W via Ethernet interface is described in the online help of the
tool.
6.3
Resetting the AMC2 4W
When a problem occurs, first, try to fix the problem directly. If
this does not solve the problem, resetting the AMC2 4W may
help:
1.
Insert the provided screwdriver into the hole as shown in
the figure below.
2.
3.
Push the reset button for at least three seconds.
The AMC2 4W will be reset and reboots. You are back in
the download program.
4.
Now it is possible to reconfigure the AMC2 4W from the
beginning.
5.
If the problem still arises, please, call your local service.
Resetting the network configurations:
1.
Reset the AMC as described above (in download program)
2.
Open the upper case of the AMC2 4W
3.
Set all six DIP switches of the RS-485 selector to ON
4.
Press the tamper switch on the upper left side of the board
The AMC2 4W will now have the following network configuration:
•
•
DHCP = 0
IP = 127.0.0.1
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
Operating | en 53
Fig. 6.2
Restarting the AMC2 4W with the provided screw driver
Fig. 6.3
Resetting the AMC2 4W to delivery state
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
54 en | Appendix
AMC2 4W | Installation manual
7
Appendix
7.1
Connecting Diagrams
Fig. 7.1
Connectors on upper PCB
Fig. 7.2
RS-485 host on upper PCB
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
Appendix | en 55
Fig. 7.3
Connecting diagram of the RS-232 serial interface
Fig. 7.4
Ethernet Network socket (RJ45)
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
56 en | Appendix
Fig. 7.5
AMC2 4W | Installation manual
Connector blocks of the AMC2 4W
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
Fig. 7.6
Power supply
Fig. 7.7
Wiegand interface
Fig. 7.8
Analog input
Fig. 7.9
Relay output
Bosch Sicherheitssysteme GmbH
Appendix | en 57
F.01U.024.965 | V 0.1 | 2006.03
58 en | Appendix
AMC2 4W | Installation manual
Fig. 7.10 Slave interface
Fig. 7.11 External tamper contact
7.2
Legend
Twisted pair connection
Transmitter
Receiver
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
8
Index | en 59
Index
A
Address Selector 37
Analog Input Devices 47
Appendix 54
Cabling 28
Conductor data 24
Configuring the Ethernet Inter-
face 52
Connecting Diagrams 54
Connectors 23
Demounting the AMC-4 27
Description of the AMC-4 15
DIL Switch 37
Dimensions 23
Display 22
Environment temperature 23
Equipment Configuration 17
Ethernet Interface 41
C
D
E
G
Grounding 29
H
Hardware 22
Housing material 23
Humidity 23
Installing the AMC-4 26
Internet 7
I
L
Legend 58
O
Opening the AMC-4 Case 28
Operating the AMC-4 50
Performance Characteristics
20
Power consumption 23
Power Supply 31
Power supply 22
Protection Class 23
Relay Outputs 44
Resetting the AMC-4 52
RS232 Host Interface 39
RS485 Extension Module Bus
42
RS485 Four Wire Connection
36
RS485 Host Interface 33, 34
RS485 Two Wire Connection
35
Safety Notes 13
Shielding 29
Status Display 50
System Overview 21
P
R
S
T
Technical Data 22
Bosch Sicherheitssysteme GmbH
F.01U.024.965 | V 0.1 | 2006.03
60 en | Index
AMC2 4W | Installation manual
U
Used Symbols 7
W
Wiegand Interface 43
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
AMC2 4W | Installation manual
Bosch Sicherheitssysteme GmbH
Index | en 61
F.01U.024.965 | V 0.1 | 2006.03
Bosch Sicherheitssysteme GmbH
Robert-Koch-Straße 100
D-85521 Ottobrunn
Germany
Telefon
(089) 6290-0
Fax
(089) 6290-1020
www.bosch-securitysystems.com
© Bosch Sicherheitssysteme GmbH, 2006