Craftsman 315.271210 Owner`s manual

Owner's Manual
iPR
0 F E S S I 0 NAL
i
318 in. PROFESSIONAL
CORDLESS DRILL-DRIVER
Variable Speed / Reversible
Model Nos.
315.271200
315.271210
315.271230
Save this manual
future reference
for
• Safety
• Features
CAUTION:
Read and
follow all Safety Rules and
Operating Instructions before
first use of this product.
Customer
Help
Line:
1-800-932-3188
Sears, Roebuck
and Co., Hoffman
Estates,
IL 60179
Visit the Craftsman web page: www.sears.com/craftsman
972000-714
12-99
•
•
•
•
USA
Assembly
Operation
Maintenance
Parts List
®
TABLE
OF CONTENTS
•
General Safety Rules .................................................................................................................................................
2-3
•
Specific Safety Rules/Symbols
3-5
•
Features .....................................................................................................................................................................
5-7
•
Assembly ....................................................................................................................................................................
8-9
•
Operation ................................................................................................................................................................
•
Maintenance ................................................................................................................................................................
15
•
Accessories
16
•
Exploded View And Repair Parts List .........................................................................................................................
17
•
Parts Ordering / Service ..............................................................................................................................................
18
_k
WARNING:
Read and understand all instructions.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal
injury.
SAVE THESE
..................................................................................................................................
.................................................................................................................................................................
Personal
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious
personal injury.
•
Dress properly. Do not wear loose clotfling or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
•
Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery
pack. Carrying tools with your finger on the switch or
inserting the battery pack into a tool with the switch on,
invites accidents.
•
Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached
to a rotating part of the tool may result in personal
injury.
•
Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable
better control of the tool in unexpected situations.
•
Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Work Area
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you
to lose control.
Electrical
•
•
•
Safety
Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a
risk of fire when used with another battery. Use battery
only with charger listed
MODEL
BATTERY PACK
CHARGER
315.271200
315,271210
Item No. 9-11030
Item No. 9--11031
Item No. 9-11040
Item No. 9-11040
315,271230
Item No. 9-11033
Item No, 9-11040
Use battery operated tool only with specifically
designated battery pack. Use of any other batteries
may create a risk of fire Use only with battery pack
listed.
2
Safety
•
INSTRUCTIONS
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
10-14
Tool Use and Care
•
•
•
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools, with sharp
cutting edges are less likely to bind and are easier to
control.
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
•
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off.
A tool that cannot be controlled with the switch is
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
•
Use only accessories that are recommended by
the manufacturer
for your model. Accessories that
may be suitable for one tool, may create a risk of injury
when used on another tool.
dangerous and must be repaired.
•
•
Disconnect battery pack from tool or place the switch
in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such
preventive safety measures reduce risk of starting the tool
accidentally.
Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
Service
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact
hidden wiring. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
Additional
Rules For Safe Operation
Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to
this tool. Following this rule will reduce the risk of
electric shock, fire, or serious injury.
Make sure your extension cord is in good condition. When using an extension cord, be sure to
use one heavy enough to carry the current your
product will draw. A wire gage size (A.W.G.) of at
least 16 is recommended for an extension cord
100 feet or less in length. A cord exceeding 100
feet is not recommended. If in doubt, use the next
heavier gage. The smaller the gage number, the
heavier the cord. An undersized cord will cause a
drop in line voltage resulting in loss of power and
overheating.
Important
Rules for Battery Tools
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when chang-
ing accessories. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
•
Do not place battery tools or their batteries near
fire or heat. They may explode. Following this rule
will reduce the risk of electric shock, fire, or serious
personal injury.
•
Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
Your battery tool should be charged in a location
where the temperature is more than 50°F but less
than 100°F. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Important Safety Instructions
For Charger
•
Save these instructions. This manual contains
important safety and operating instructions for
battery charger part number 9-11040. Following this
rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
Before using battery charger, read all instructions
and cautionary markings in this manual, on
battery charger, and product using battery
charger. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
To reduce risk of injury, charge only nickelcadmium and nickel metal hydride type rechargeable batteries. Other types of batteries may burst
causing personal injury and damage. Following this
rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
•
•
To reduce risk of damage to charger body and
cord, pull by charger plug rather than cord when
disconnecting
charger. Following this rule will
reduce the risk of electric shock, fire, or serious
•
personal injury.
Make sure cord is located
•
stepped on, tripped over, or otherwise subjected
to damage or stress. Following this rule will reduce
the risk of serious personal injury.
An extension cord should not be used unless
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
50'
100'
Cord Size (AWG)
16
16
16
Do not operate charger with a damaged cord or
plug. If damaged, have replaced immediately by a
qualified serviceman. Following this rule will reduce
the risk of electric shock, fire, or serious personal
injury.
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to a qualified serviceman. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
Do not disassemble charger; take it to a qualified
serviceman when service or repair is required.
Incorrect reassembly may result in a risk of
electric shock or fire. Following this rule will reduce
the risk of electric shock, fire, or serious personal
injury.
•
To reduce the risk of electric shock, unplug
charger from outlet before attempting any maintenance or cleaning. Turning off controls will not
reduce this risk. Following this rule will reduce the
risk of electric shock, fire, or serious personal injury.
•
Do not use charger outdoors. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
•
Disconnect charger from power supply when not
in use. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
so that it will not be
absolutely necessary.
Use of improper extension
cord could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
25'
Note: AWG = American Wire Gage
Do not expose charger to rain or snow. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
Use of an attachment not recommended
or sold
by the battery charger manufacturer
may result in
a risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
Cord Length (Feet)
,_
DANGER: RISK OF ELECTRIC SHOCK. DO NOT
TOUCH UNINSULATED PORTION OF OUTPUT
CONNECTOR OR UNINSULATED BATTERY
TERMINAL.
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
tool. If you loan someone this tool, loan them
these instructions also. Following this rule will
reduce the risk of electric shock, fire, or serious
personal injury.
SYMBOLS
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
min
Minutes
Time
Alternating Current
Type or a characteristic of current
Direct Current
Type or a characteristic of current
no
No Load Speed
Rotational speed, at no load
•..Imin
Revolutions or Reciprocation
A
Safety Alert Symbol
Per Minute
Revolutions, strokes,
surface speed, orbits etc. per minute
Indicates danger, warning or caution.
It means attentionrH Your safety is
involved.
DEFINITIONS
A)
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others.
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
B)
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others•
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
C)
CAUTION: Failure to obey a safety warning may result in property damage or personal injury
to yourself or to others• Always follow the safety precautions to reduce the risk of fire, electric
shock and personal injury.
D)
NOTE: Advises you of information or instructions vital to the operation or maintenance of the
equipment.
PRODUCT
DRILL-DRIVER
SPECIFICATIONS:
315.271200
315.271210
315.271230
Chuck
3/8 in. Keyless
3/8 in. Keyless
3/8 in. Keyless
Motor
DC Motor 9.6 Volt
DC Motor 12 Volt
DC Motor 14.4 Volt
Gear Train
Two Speed
Two Speed
Two Speed
Switch
Variable Speed
Variable Speed
Variable Speed
No Load Speed
0-350 RPM (Low)
0-1100 RPM (High)
0-350 RPM (Low)
0-1100 RPM (High)
0-400 RPM (Low)
Clutch
24 Positions
24 Positions
24 Positions
Maximum Torque
250 in./Ibs
350 in./Ibs
380 in./Ibs
Item No. 9-11040
Item No. 9_-11040
Item No. _9-11040
Input
120 V, 60 Hz, AC only
120 V, 60 Hz, AC only
120 V, 60 Hz, AC only
Charging Voltage
9.6 - 24 Volt
9.6 - 24 Volt
9.6 - 24 Volt
Charge Rate
1 Hour
1 Hour
1 Hour
Item No. 9--11030
Item No. 9_-11031
Item No. 9--11033
CHARGER
BATTERY
KNOW
PACK
YOUR
DRILL-DRIVER
See Figure 1.
Before attempting to use your drill-driver, familiarize
yourself with all operating features and safety
requirements.
,_
WARNING: Carefully read through this entire owner's
manual before using your new drill-driver. Pay close
attention to the Rules For Safe Operation, Warnings
and Cautions. If you use your drill-driver properly and
only for what it is intended, you will enjoy years of safe,
reliable service.
VARIABLE
0-1400 RPM (High)
SPEED
This tool has a variable speed switch that delivers higher
speed with increased trigger pressure. Speed is controlled
by the amount of switch trigger depression.
TWO SPEED
GEAR
TRAIN
Your drill-driver has a two speed gear train designed for
drilling or driving at HI or LO speeds. A slide switch is
located on top of your drill to select either HI or LO speed.
FORWARD/REVERSE
(DIRECTION
SELECTOR
OF ROTATION SELECTOR)
Your drill-driver has a forward/reverse
_1
WARNING:
Do not allow familiarity with your drilldriver to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe
injury.
KEYLESS
CHUCK
Your drill-driver has a keyless chuck that allows you to hand
tighten or release drill bit in the chuck jaws.
SWITCH
To turn your drill-driver ON, depress the switch trigger.
Release switch trigger to turn your drill-driver OFF.
SWITCH
LOCK
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting
when not in use.
selector located
above the switch trigger.
WRIST
STRAP
A wrist strap is provided to reduce the chances of dropping
your drill-driver. Place One hand through the wrist strap
when carrying tool.
BIT STORAGE
When not in use, bits provided with your drill-driver can be
placed in the storage area located on the top of the motor
housing.
LEVEL
To keep drill bit level during drilling operations, a level is
located on the top and end of the motor housing.
,_
WARNING: If any parts are missing, do not operate
your drill-driver until the missing parts are replaced.
Failure to do so could result in possible serious
personal injury.
TWO SPEED
GEARTRAIN(HI-LO)
LEVEL
KEYLESS
CHUCK
BIT STORAGE
AREA
YELLOWLIGHT"ON" ANDRED
LIGHTFLASHINGINDICATES
DEFECTIVEBATTERYPACK
DIRECTIONOF
ROTATIONSELECTOR
(FORWARD/REVERSE)
TORQUE
ADJUSTMENT
RING
SWITCH
TRIGGER
CHARGER
REDLIGHT "ON" INDICATES
FASTCHARGINGMODE
BATTERY
PACK
GREENLIGHT "ON" INDICATESFULLY
CHARGEDANDSLOWCHARGING
TO MAINTAINBATTERYPACK
WRISTSTRAP
_
SCREWDRIVERBITS
Fig. 1
CHARGER
See Figure 2.
Your charger has a "key hole" hanging feature for eonvenientl space saving storage. Screws should be installed so that
center distances are 4-1/8 inches apart.
4-1/8in.
CHARGER
BATTERYPACKSHOWN
IN CHARGER
BACKSIDE OF CHARGER
Fig. 2
7
INSTALLINGBITS
,_WARNING:
Do not insert drill bit into chuck jaws
and tighten as shown in Figure 4. This could cause
drill bit to be thrown from drill resulting in possible
serious personal injury or damage to the chuck.
See Figure 3.
H
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 10.
•
Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use.
Also, raise the front of your drill slightly to keep the bit
from falling out of the chuck jaws.
•
Insert drill bit into chuck the full length of the jaws as
shown in Figure 3.
UNLOCK
CHUCKJAWS_
WRONG
DRILLBIT
REMOVING
CHUCKSLEEVE
RIGHT
Fig. 3
Tighten the chuck jaws on drill bit. To tighten, grasp
and hold the drill with one hand, while rotating the
chuck sleeve with your other hand.
Note: Rotate the chuck sleeve in the direction of the
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 10.
•
Loosen the chuck jaws from drill bit.
•
To loosen, grasp and hold the drill with one hand,
while rotating chuck sleeve with your other hand.
Note: Rotate chuck sleeve in the direction of the arrow
marked UNLOCK to loosen the chuck jaws.
•
Do not use a wrench to tighten or loosen the chuck
jaws.
•
Remove drill bit from chuck jaws.
arrow marked LOCK to tighten chuck jaws.
•
BITS
See Figure 3.
LOCK
•
Fig. 4
Do not use a wrench to tighten or loosen the chuck
jaws.
8
TO ATTACH
BATTERY
PACK TO DRILL
TO REMOVE
See Figure 6.
See Figure 5.
Note: Battery pack is shipped in a low charge condition.
Therefore, it must be charged prior to use. Refer to page 10,
"CHARGING BATTERY PACK" for charging instructions.
•
•
•
Lock the switch trigger by placing the direction
rotation selector in center position. See Figure
Align raised ribs on battery pack with grooves
bottom of drill, then attach battery pack to drill
shown in Figure 5.
of
10.
on
as
BATTERY
PACK
FROM DRILL
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 10.
•
Depress latch located on front of battery pack (1) to
release battery pack.
•
Pull forward on battery pack (2) to remove from drill.
DEPRESSLATCHTO
RELEASEBATTERYPACK
Make sure latch on battery pack snaps in place and
battery pack is secured to drill before beginning
operation.
RAISEDRIBS
LATCH
PULL
FORWARD
TO REMOVE
GROOVES
BATTERYPACK
BAI-rERYPACK
Fig. 5
_1
CAUTION" When attaching battery pack to your
drill, be sure raised ribs and grooves align properly
and latch snaps in place properly. Improper assembly
can cause damage to drill and battery pack.
Fig. 6
,_
If after one hour red light is still flashing, this indicates a
defective battery pack and should be replaced.
WARNING:
Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
CHARGING
BATTERY
Green light on indicates battery pack is fully charged
and slow charging to maintain battery pack.
Yellow light on and red light flashing indicates defective
battery pack. Return battery pack to your nearest Sears
Repair Center for checking or replacing.
PACK
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it until light on front of charger changes
from red to green.
•
When your battery pack becomes fully charged, the red light
will turn OFF and the green light will turn ON.
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (drilling followed by
recharging) for them to become fully charged.
•
After normal usage, 1 hour of charging time is required to be
fully charged. A minimum charge time of 1-1/2 hours is
required to recharge a completely discharged tool.
TO CHARGE
•
The battery pack will become slightly warm to the touch while
charging. This is normal and does not indicate a problem.
•
Do not place charger in an area of extreme heat or
cold. It will work best at normal room temperature.
•
When the batteries become fully charged, unplug your
charger from power supply and remove the battery
pack.
•
Charge battery pack only with the charger provided.
•
Make sure power supply is normal
120 volts, 60 Hz, AC only.
•
Connect charger to power supply.
•
Attach battery pack to charger by aligning raised ribs
on battery pack with grooves in charger, then slide
battery back onto charger. See Figure 7.
house voltage,
LED FUNCTION
LED WILL BE LIGHTED TO INDICATE STATUS OF
CHARGER AND BATTERY PACK:
BATTERY
PACK
TO
REMOVE
•
Red LED Lighted = Fast Charging Mode.
•
Green LED Lighted = Fully Charged And Slow
Charging To Maintain Battery Pack.
•
Red LED Flashing = Hot Or Deeply Discharged
Battery Pack. Also Defective Battery Pack After 1
Hour.
•
Yellow LED Lighted and Red LED Flashing =
Defective Battery Pack.
CHARGER
IMPORTANT
INFORMATION
HOT BATTERIES
TO
ATTACH
FOR
RECHARGING
Under extreme continuous use, the batteries in your
battery pack will become hot. You should let a hot battery
pack cool down for approximately 1 hour before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the red light on your
battery charger to flash. When battery pack cools down,
red light will glow continuously indicating fast charging
mode, 1 hour charge time. Once the battery pack cools
down, it will recharge battery pack in fast charging mode
as normal.
GROOVES
Fig. 7
•
OF CHARGER
Red light should turn on. Red light indicates fast
charging mode.
If red light is flashing, this indicates battery pack is
deeply discharged or hot.
Note: This situation only occurs when extreme continuous
use of your drill causes the batteries to become hot. It
does not occur under normal circumstances.
Refer to
"CHARGING BATTERY PACK" for normal recharging of
batteries. If the charger does not charge your battery pack
under normal circumstances, return both the battery pack
and charger to your nearest Sears repair center for
electrical check.
If battery pack is hot, red light should become steady
after battery pack has cooled down.
If battery pack is deeply discharged, red light should
become steady after voltage has increased, normally
within 60 minutes.
10
SWITCH
SWITCH
See Figure 8.
See Figure 10.
To turn your drill ON, depress the switch trigger. To turn it
OFF, release the switch trigger.
The switch trigger can be locked in the OFF position. This
feature can be used to prevent the possibility of accidental
starting when not in use. To lock switch trigger, place the
direction of rotation selector in center position.
FORWARD/REVERSE
SELECTOR
SELECTOR
CENTERPOSITION
(LOCK)
CENTERPOSITION
(LOCK)
SWITCH
TRIGGER
VARIABLE
FORWARD
_
This tool has a variable speed switch that delivers higher
speed and torque with increased trigger pressure. Speed
is controlled by the amount of switch trigger depression.
WARNING:
Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
REVERSIBLE
See Figure 10.
Note: You might hear a whistling or ringing noise from the
switch during use. Do not be concerned, this is a normal
part of the switch function.
This tool has the feature of being reversible. The direction
of rotation is controlled by a selector located above the
switch trigger. With the drill held in normal operating
position, the direction of rotation selector should be
positioned to the left of the switch for drilling. The drilling
direction is reversed when the selector is to the right of
the switch. When the selector is in center position, the
switch trigger is locked.
GEAR TRAIN
See Figure 9.
Your drill has a two-speed gear train designed for drilling
or driving at LO (1) or HI (2) speeds. A slide switch is
located on top of your drill to select either LO (1) or HI (2)
speed. When using drill in the LO (1) speed range, speed
will decrease and unit will have more power and torque.
When using drill in the HI (2) speed range, speed will
increase and unit will have less power and torque. Use
LO (1) speed for high power and torque applications and
HI (2) speed for fast drilling or driving applications.
TWO SPEED
GEARTRAIN(HI-LO)
Fig. 10
Fig. 8
SPEED
TWO SPEED
LOCK
CAUTION;
To prevent gear damage, always allow
chuck to come to a complete stop before changing
the direction of rotation or the two speed gear train
(hi-lo).
To stop, release switch trigger and allow the chuck to
come to a complete stop.
LO
SPEED
HI
SPEED
Fig. 9
11
KEYLESSCHUCK
ADJUSTINGRING
TO DECREASE
TORQUE
See Figure 11.
A keyless chuck has been provided with your drill to allow
for easy installation and removal of bits. As the name
implies, you can hand tighten or release drill bits in the
chuck jaws. Arrows on the chuck indicate which direction
to rotate the chuck sleeve in order to LOCK (tighten) or
UNLOCK (release) the chuck jaws. Loosen the chuck
sleeve by rotating it counterclockwise with one hand.
Insert drill bit into the chuck the full length of the jaws,
tighten securely by rotating the chuck sleeve in clockwise
direction.
UNLOCK
(Release)
TOINCREASE
TORQUE
CHUCKJAWS_
Fig. 12
Note: Remember the two-speed feature (HI-LO) when
setting torque. The amount of torque will vary depending
on which speed setting you have your drill-driver. Switching to LO speed will increase torque. Switching to HI
speed will decrease torque.
DRILLBIT
BIT STORAGE
See Figure 13.
LOCK
(Tighten)
When not in use, bits provided with your drill can be
placed in the storage area located on the top of your drill
as shown in Figure 13.
CHUCKSLEEVE
Fig. 11
WARNING:
Do not hold chuck sleeve with one
hand and use power of the drill to tighten chuck jaws
on drill bit. Chuck sleeve could slip in your hand or
your hand could slip and come in contact with
rotating drill bit. This could cause an accident
resulting in serious personal injury.
ADJUSTABLE
TORQUE
SCREWDRIVER
BIT
CLUTCH
Your drill is equipped with an adjustable torque clutch for
driving different types of screws into different materials.
The proper setting depends on the type of material and
the size of screw you are using.
TO ADJUST
SCREWDRIVER
BIT
TORQUE
•
Identify the twenty four torque indicator settings
located on the front of your drill. See Figure 12.
•
Rotate adjusting ring to the desired setting.
1 - 4
For driving small screws.
5 - 8
For driving screws into soft
material.
9 - 12
For driving screws into soft and
hard materials.
• 13 - 16
For driving screws in hard wood.
• 17 - 20
For driving large screws.
• 21 -,11
For heavy drilling.
•
BITSTORAGEAREA
Fig. 13
12
APPLICATIONS
DRILLING
(Use drill-driver only for the purpose listed below)
•
Drilling in wood.
See Figure 15.
•
Drilling in ceramics, plastics, fiberglass, and laminates.
•
•
Drilling in both hard and soft metals.
Using driving accessories, such as driving screws
with screwdriver bits.
•
Mixing paints.
LEVEL
LEVEL
DRILLING
See Figure 14.
A convenient feature provided on your drill is a level. It is
recessed in the motor housing on top and end of your
drill. It can be used to keep drill bits level during most
drilling operations.
END VIEW
TOP VIEW
LEVEL
Fig. 15
When drilling hard smooth surfaces use a center punch to
mark desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. However,
the low speed feature allows starting holes without center
punching if desired. To accomplish this, simply operate
your drill at a low speed until the hole is started.
The material to be drilled should be secured in a vise or
with clamps to keep it from turning as the drill bit rotates.
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
Move the drill bit into the workpiece applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
_i
WARNING:
Be prepared for binding or bit
breakthrough. When these situations occur, drill has
a tendency to grab and kick opposite to the direction
of rotation and could cause loss of control when
breaking through material. If not prepared, this loss
of control can result in possible serious injury.
When drilling metals, use a light oil on the drill bit to keep
it from overheating. The oil will prolong the life of the bit
and increase the drilling action.
If the bit jams in workpiece or if the drill stalls, release
switch trigger immediately. Remove the bit from the
workpiece and determine the reason for jamming.
13
CHUCK
Insert allen wrench in chuck and tighten chuck jaws
securely, Tap sharply with a mallet in a counterclockwise direction. This will loosen chuck on the spindle, It
can now be unscrewed by hand. See Figure 18.
REMOVAL
See Figures 16, 17, and 18.
The chuck must be removed in order to use some
accessories, To remove:
•
Lock the switch trigger by placing the direction of
rotation selector in center position, See Figure 10.
•
Insert a 5/16 inch or larger allen wrench (hex key
wrench) into the chuck of your drill and tighten the chuck
jaws securely.
•
Tap the allen wrench sharply with a mallet in a
clockwise direction, See Figure 16. This will loosen
the screw in the chuck for easy removal.
MALLET
CHUCKJAWS
Fig. 18
TO RETIGHTEN
ALLEN
WRENCH
A LOOSE
CHUCK
The chuck may become loose on spindle and develop a
wobble. Also, the chuck screw may become loose causing the chuck jaws to bind and prevent them from closing.
To tighten, follow these steps:
KEYLESS
CHUCK
Fig. 16
Lock the switch trigger by placing the direction of
rotation selector in center position, SeeFigure 10.
Open chuck jaws and remove allen wrench. Remove
the chuck screw by turning it in a clockwise direction.
See Figure 17.
Insert allen wrench into chuck and tighten chuck jaws
securely. Tap allen wrench sharply with a mallet in a
clockwise direction. This will tighten chuck on the
spindle,
Note: The screw has left hand threads.
SCREWDRIVER
•
Open the chuck jaws and remove allen wrench.
•
Tighten the chuck screw.
Note: The chuck screw has left hand threads.
Fig. 17
14
WARNING:
When servicing use only identical
Craftsman replacement parts. Use of any other
parts may create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, carbon dust, etc.
Do not abuse power tools. Abusive practices can
damage tool as well as workpiece.
Only the parts shown on parts list, page 17, are intended
to be repaired or replaced by the customer. All other parts
should be replaced by a qualified service technician at an
authorized service facility.
,_,
,_
WARNING:
De not at any time let brake fluids,
gasoline, petroleum-based products, penetrating oils,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy
plastic.
WARNING'. De not attempt to modify this tool or
create accessories not recommended for use with
this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
BATTERIES
The battery pack for your drill-driver is equipped with
nickel-cadmium rechargeable batteries. Length of service
from each charging will depend on the type of work you
are doing.
The batteries in this tool have been designed to provide
maximum trouble free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry,
could result in a serious burn.
•
Store and charge your batteries in a cool area.
Temperatures above normal room temperature will
shorten battery life.
•
Never store batteries in a discharged condition.
Recharge them immediately after they are
discharged.
•
All batteries gradually lose their charge. The higher
the temperature the quicker they lose their charge. If
you store your tool for long periods of time without
using it, recharge the batteries every month or two.
This practice will prolong battery life.
To obtain the longest possible battery life, we suggest the
following:
BATTERY PACK REMOVAL
FOR RECYCLING
To preserve natural resources, please
recycle or dispose of properly.
This product contains nickel-cadmium
batteries. Local, state or federal laws
may prohibit disposal of nickel-cadmium
batteries in ordinary trash.
_
Consult your local waste authority for information
regarding available recycling and/or disposal options.
AND PREPARATION
WARNING:
Upon removal, cover the battery pack's
terminals with heavy duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
OVERLOAD
Your drill has a built-in overload protector to protect the motor during overloading or prolonged use. The overload
protector automatically activates to break the circuit. When this occurs, allow your drill to cool a few seconds before
resuming operation.
15
Thefollowingrecommended
accessories
arecurrentlyavailableatSearsRetailStores.
• 17-Pc.PowerScrewdriver/Nutdriver
SetandCase
• 6-Pc.ExtraLengthMageitePowerBitSet
• 30-Pc.PowerScrewdriver/Nutdriver
SetandCase
• HighSpeedBits(ForWoodor Metal)......3/4
in. Max.
,_i
d_,
WARNING:
The use of attachments or accessories
not listed might be hazardous.
WARNING:
The operation of any power tool can
result in severe eye damage. Before
safety glasses with side shields and
Safety Mask for use over eyeglasses
Retail Stores.
result in foreign objects being thrown into your eyes, which can
beginning power tool operation, always wear safety goggles or
a full face shield when needed. We recommend Wide Vision
or standard safety glasses with side shields, available at Sears
WARRANTY
FULL ONE YEAR WARRANTY
ON £RRFI"$HRN
PROFESSIONAL
CORDLESS DRILL-DRIVER
If this I:RRFI'$MRN Professional Cordless Drill-Driver fails due to a defect in material or workmanship within one year
from the date of purchase, Sears will repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY RETURNING
THE UNITED STATES.
THE TOOL TO THE NEAREST SEARS STORE IN
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck
and Co., Dept. 817WA, Hoffman
Estates,
IL 60179
SAVETHESEINSTRUCTIONS
16
CRAFTSMAN
3/8 in. PROFESSIONAL
CORDLESS
DRILL-DRIVER
MODEL NOS. 315.271200 / 315.271210 / 315.271230
i
I
I
in all correspondence regarding your CRAFTSMAN 3/8 in. PROFESSIONAL CORDLESS DRILL-DRIVER
The
model
number repair
will beparts.
found on a plate attached to the motor housing. Always mention the model number
or when
ordering
SEE BACK
PAGE
FOR PARTS
ORDERING
|
INSTRUCTIONS
3
5
4
PARTS
Key
No.
LIST
Part
Number
Description
1
616478-003
Screw (Special) ................................................................................
1
2
981502-001
Chuck (Item No. _9-20955) ................................................................
1
3
981501-001
Logo Plate ........................................................................................
1
4
Battery Pack (Item No. _9-11030 Model No. 315.271200) ............. 1
Battery Pack (item No. _9-11031 Model No. 315.271210) ............. 1
Battery Pack (Item No. _9-11033 Model No. 315.271230) ............. 1
5
6
Quan.
Battery Charger (Item No, 9-11040) ................................................
1
981498-001
Carrying Case - Not Shown .............................................................
1
972000-714
Owner's Manual
* Can Be Purchased At Your Nearest Sears Retail Store
17
In U.S.A. or Canada
for in-home major brand repair service:
Call 24 hours a day, 7 days a week
1-800-4-MY-HOME
Para pedir servicio de reparacibn
sM(1-800-469-4663)
a domicilio
- 1-800-676-5811
Au Canada pour tout le service ou les pieces - 1-800-469 4663
For the repair
or replacement
parts you need:
Call 6 a.m. - 11 p.m. CST, 7 days a week
Parts Direct s°
1-800-366-PART
Para ordenar
piezas con entrega
(1-800-366-7278)
a domicilio - 1-800-659-7084
For the location of a Sears Service Center in your area:
Call 24 hours a day, 7 days a week
1-800-488-1222
To purchase or inquire about a Sears Maintenance Agreement:
Call 7 a.m. - 5 p.m. CST, Monday - Saturday
1-800-827-6655
HomeCentralso
h,=
_dl