Operating and Installation Instructions
for cooker hoods
DA 326 i, DA 326 i EXT
DA 327 i, DA 327 i EXT
DA 329 i, DA 329 i EXT
It is essential to read these
operating and installation instructions
before installing or using the machine,
to avoid the risk of accident
or damage to the machine.
Q\@ä}
M.-Nr. 05 473 620
Contents
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Guide to the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Description of the functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cleaning and care
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Grease filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Primary filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Secondary filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Fitting / replacing the active charcoal filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Defective lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Installation
Fitting accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
1. Non-return flap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2. Reducing collar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
3. Runners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4. Fit the furniture door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5. Position the appliance in the wall unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6. Align the height of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
7 a. Fitting a DFB lightshield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
7 b. Fitting a lightshield to match the kitchen furniture . . . . . . . . . . . . . . . . . . . . . 28
8. Align the depth of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
9 a. Fit side spacers at the sides of the appliance . . . . . . . . . . . . . . . . . . . . . . . . 30
9 b. Spacer strip for the rear of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
9 c. Light cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
10 a. Set up for vented extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
10 b. Set up for recirculation connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
11. Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Special fitting instructions
Fitting into wall unit with 19 mm thick carcase sides . . . . . . . . . . . . . . . . . . . . 33
Installing in a 70 or 90 cm wide wall unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Connection for air extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2
Caring for the environment
Caring for the environment
Disposal of packing material
Disposal of your old appliance
The transport and protective packaging has been selected from materials
which are environmentally friendly for
disposal and can normally be recycled.
Old appliances contain materials which
can be reclaimed or recycled. Please
contact your dealer, your waste collection centre or scrap merchant about
potential recycling schemes.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
Rather than just throwing these materials away, please ensure they are offered for recycling.
Ensure that the appliance presents no
danger to children while being stored
for disposal.
See the appropriate section in the
Warning and Safety instructions.
3
Warning and Safety instructions
Warning and Safety instructions
This appliance conforms to current
safety requirements. Inappropriate
use could, however lead to risk of
accidents to the user and damage
to the appliance.
Before using this appliance for the
first time read the operating instructions carefully. They contain important information on safety, use and
maintenance of the appliance. This
way you will avoid the risk of accidents and damage to the appliance.
Keep these operating instructions in
a safe place and ensure that new
users are familiar with the content.
Pass them on to any future owner.
Appropriate use
The appliance is intended for domestic use only.
The manufacturer cannot be held responsible for any damage caused by
improper use or by non-observance of
these instructions.
4
Technical safety
Before connecting the cooker
hood to the mains supply make
sure that the voltage and frequency details given on the data plate correspond with the on-site electricity supply, otherwise the appliance could be
damaged. If in doubt consult a qualified electrician.
The electrical safety of this appliance can only be guaranteed
when continuity is complete between
the appliance and an effective earthing
system which complies with local and
national regulations. It is most important that this basic safety requirement is
tested by a qualified electrician.
The manufacturer cannot be held responsible for the consequences of an
inadequate earthing system (e.g. electric shock).
Installation work and repairs may
only be carried out by suitably
qualified and competent persons to ensure safety. Repairs and other work by
unqualified persons could be dangerous and the manufacturer will not
be held responsible.
Warning and Safety instructions
The appliance is only completely
isolated from the mains supply
when:
– it is switched off at the fused spur
connection, or
– it is switched off at the wall socket
and the plug has been withdrawn
(do not pull on the cable, only on the
plug), or
– the mains fuse is withdrawn.
Ensure current is not supplied to the appliance while maintenance or repair
work is being carried out.
Do not connect the appliance to
the mains electricity supply by an
extension lead.
Extension leads do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
Use of the appliance
Do not let small children play with
the appliance or its controls. Supervise its use by the elderly or infirm.
When fitted above an open grill the
cooker hood must not be used in
recirculation mode.
by the suction of the cooker hood,
parts of which could then be damaged.
Always switch the cooker hood on
when a cooking zone is in use,
otherwise condensation may collect in
the hood, which could cause corrosion.
When cooking with oil or fat, chip
pans and deep fat fryers etc, do
not leave the pans unattended. Never
leave an open grill unattended when
grilling. Overheated oil and fat can ignite and could set the cooker hood on
fire.
Do not use the cooker hood without the grease filter in place.
This way you will avoid the risk of
grease and dirt getting into the appliance and hindering its smooth operation.
Clean or change the filter regularly.
An over-greasy filter is a fire hazard.
Under no circumstances use a
steam cleaner to clean this appliance. Pressurised steam could
reach the electrical components and
cause a short circuit.
Never use an open flame beneath
the cooker hood. To avoid the
danger of fire do not flambé or grill over
an open flame. When switched on the
cooker hood could draw flames into the
filters. Fat particles drawn into the
cooker hood present a fire hazard.
When using the cooker hood over
a gas hob ensure that any burners
in use are always covered by a pan.
Otherwise flames could be drawn up
5
Warning and Safety instructions
Installation
– The distance between the top of the
cooker/hob and the bottom of the
cooker hood must measure at least:
– 45 cm above electric cookers/hobs,
– 65 cm above gas cookers/hobs,
– 65 cm above a Miele or Imperial
electric open grill.
For other manufacturer’s cooking appliances maintain the safety distance
as recommended in their Installation
and Operating instructions.
If more than one appliance is fitted beneath the cooker hood and they have
different minimum safety distances to
the cooker hood, select the higher distance.
Safety regulations prohibit the fitting of a cooker hood over solid
fuel stoves.
All ducting, pipework and fittings
must be of non-flammable material. These can be obtained from the
Miele Spare Parts department or from
builders’ merchants.
The appliance must not be connected to a chimney or vent flue
which is in use. Neither should it be
connected to ducting which ventilates
rooms with fireplaces.
If exhaust air is to be extracted into
a chimney or ventilation duct no
longer used for other purposes, take
professional advice.
6
Warning and Safety instructions
When using the cooker hood at the
same time as another heating appliance which depends on the air in the
room, (e.g. gas, oil or coal fired
heaters, continuous flow or other water
heaters, gas cooker, gas hob or gas
oven) special care must be taken, as
the action of the cooker hood extracts
air from the room, which these types of
heater need for combustion.
In countries where there are areas
which may be subject to infestation by cockroaches or other vermin,
pay particular attention to keeping the
appliance and its surroundings in a
clean condition at all times. Any damage which might be caused by cockroaches or other vermin will not be
covered by the appliance guarantee.
Appliances with external fans
In order to ensure safe operation, and
to prevent the gases given off by the
heating appliances from being drawn
back into the room when the extractor
and the heater are in operation simultaneously, an underpressure in the room
of 0.04 mbar (4 pa) is the maximum
permissible.
Ventilation can be maintained by air inlets which cannot be blocked, in windows, doors and outside wall vents, or
by other technical measures, such as
ensuring that the extractor can only be
switched on when the heating appliance is switched off or vice-versa.
N.B.: The overall ventilation condition of
the dwelling must be taken into account.
If in any doubt, the advice of a competent builder or, for gas, a “Corgi” installer (gas installer) must be sought.
If the cooker hood is used in recirculation mode (with active charcoal filters) ,
there are no restrictions.
For appliances with an external fan
motor fitted (EX models) the connection
of the two units must be made using
the connection cable and the plug connectors. Make sure the correct combination of the two appliances has been
selected.
Separate instructions are supplied with
the external fan.
Disposal of your old appliance
Before discarding an old appliance switch off and disconnect
it from the power supply. Cut off and
render any plug useless. Cut off the
cable directly behind the appliance to
prevent misuse. This should be done
by a competent person.
The manufacturer cannot be held responsible for any damage caused
by non-observance of these instructions.
7
Guide to the appliance
Guide to the appliance
8
Guide to the appliance
b
Exhaust stub ø 150 mm
c
Active charcoal filter slot
d
Control panel
e
Pull-out
deflector plate
f
DFB lightshield
(Special accessory; supplied as
standard in Australia)
g
Secondary grease filter
h
Hob illumination
i
Primary grease filter
j
Light switch for hob
illumination
k
On/Off switch for the
fan
l
Power level
switches
You can select one of three power levels or an intensive level, depending on
how much the air needs to be filtered.
9
Description of the functions
Description of the functions
The cooker hood works
. . . by air extraction:
The air is drawn in, cleaned by a primary filter and then passed through a
secondary filter before being directed
outside.
The cooker hood is fitted with a nonreturn flap .
This flap is closed when the cooker
hood is switched off. No exchange of
room air and outside air can take
place. When the cooker hood is
switched on the non-return flap opens
for the cooking smells to be blown directly outside.
. . . by air recirculation:
The air is drawn in and cleaned first by
the primary filter, then the secondary filter before passing through an active
charcoal filter. The cleaned air is then
recirculated back into the kitchen
through a vent in the top of the cooker
hood.
Before using the cooker hood for
the first time in recirculation mode,
ensure that the active charcoal filter
is in place. See Section on "Cleaning and care".
10
. . . with an external fan
The EX models are designed to be connected to an external fan located outside the room.
The external fan is connected to the
cooker hood by a control cable and is
operated by the control panel on the
cooker hood.
Operation
Operation
To switch the fan on
To switch the fan off
Pull the deflector plate out approx. 5
cm.
The cooker hood will then begin to
operate at power level “II”.
Press the On/Off switch to turn the
fan off
Selecting the power level
Depending on how much the air needs
to be filtered, there are four power levels available.
For normal cooking a low to medium
level is usually sufficient.
For frying or cooking food with a strong
aroma the highest level is recommended.
or
Push the deflector plate back in.
The next time the deflector plate is
pulled out the cooker hood will operate
at power level “II”.
Switching the lighting on or off
The lighting for illuminating the hob can
be switched on or off independently of
the fan.
Lower level
Pull the deflector plate out approx. 3
cm.
Higher level
Use the power level switches to select the power level required.
The indicator lamps show which power
level has been chosen.
Press the switch for the lighting.
When the lighting is switched on the
indicator light above the switch
comes on.
To switch the lighting off:
Press the switch for the lighting
again
or
Push the deflector plate back in.
The next time the deflector plate is
pulled out the light will come back on.
11
Cleaning and care
Cleaning and care
Before any cleaning or maintenance
work the cooker hood must be disconnected from the mains supply.
Ensure that:
- it is switched off at the fused spur
connection or
- it is switched off at the wall socket
and the plug has been withdrawn
(do not pull on the cable, only on
the plug), or
- the mains fuse is withdrawn.
Ensure current is not supplied to the
appliance while maintenance or repair work is being carried out.
Housing
The surfaces can be cleaned using hot
water to which a little mild washing-up
liquid has been added. Dry with a soft
cloth.
Never use cleaners which scour or
contain chlorine, acids or soda.
These would damage the surface of
the cooker hood.
For stainless steel surfaces a mild nonabrasive proprietary stainless steel
cleaner is suitable.
12
Grease filters
Re-usable metal filters are fitted which
remove solid particles (oil, dust, etc.)
from the kitchen vapours, preventing
soiling of the cooker hood.
The cooker hood has a primary filter
which is visible on the underside of the
appliance. A secondary filter is situated above it in the appliance.
The filters should be cleaned regularly
(at least every 3-4 weeks) to avoid a
build-up of fat.
Important! Always clean both filters.
An over saturated filter is a fire
hazard.
Cleaning and care
Primary filter
To remove the primary filter pull the
deflector plate out slightly.
Switch the fan off.
Clean the filters –
– by hand: with a nylon brush in a
mild solution of hot water and washing up liquid.
– in a dishwasher: place the filters
with the short side upright in the
lower basket, ensuring the spray arm
is not obstructed.
Holding the primary filter at the front,
tilt it approx. 3 cm downwards and
then pull it towards you to remove it.
Secondary filter
Pull the deflector plate out to its full
extension.
The secondary filter will now be visible.
DA 327, 329: The primary filter can be
folded up if necessary to get it in the
dishwasher. To do this open the catches in the middle of the filter.
Depending on the cleaning agent
used, cleaning the grease filters in
a dishwasher can cause permanent
discolouration to the surface of the
filters. However, this will not affect
the functioning of the grease filters
in any way.
After cleaning, leave the filters to dry
on an absorbent surface before putting them back in place.
Holding it by the handle pull it downwards to remove it.
When removing the filters for cleaning also clean off any residues of oil
or fat from the now accessible housing to prevent the risk of these catching fire.
13
Cleaning and care
Replacing the filters
Secondary filter:
Fit the filter into the appliance so that
it hooks into position at the back,
then push it upwards at the front and
make sure it engages in position on
the left and right hand sides.
Turn the filter so that the red plastic
guides are at the front and facing upwards.
With the deflector plate pulled out, insert the primary filter from below and
hold in position.
Primary filter:
Press the filter gently upwards and
at the same time push the deflector
plate in. The filter will slide into its
holders.
DA 327i, 329i:
– Open the catches.
– Open out the filter and secure the
catches.
14
Cleaning and care
Fitting / replacing the active
charcoal filter
For recirculation mode the active charcoal filter has to be used in addition to
the grease filters. It is designed to absorb cooking odours.
The active charcoal filter is fitted into a
slot on the front of the appliance housing.
Active charcoal filters can be obtained
from your dealer or the Miele Spare
Parts Department. Refer to the section
“Technical data” for type and reference number.
Follow the instructions supplied with
the active charcoal filter when fitting it.
Replace the filter when it no longer absorbs kitchen odours effectively. It
should, however, be replaced at least
every 6 months.
15
Cleaning and care
Defective lighting
If the lighting does not work the light
tube may need replacing or the starter
could be defective.
Before any cleaning or maintenance
work the cooker hood must be disconnected from the mains supply.
Ensure that:
- it is switched off at the fused spur
connection or
- it is switched off at the wall socket
and the plug has been withdrawn
(do not pull on the cable, only on
the plug), or
- the mains fuse is withdrawn.
Ensure current is not supplied to the
appliance while maintenance or repair work is being carried out.
Take out the primary filter as already
described.
Unscrew the fixing screws on the
right and left hand sides of the light
cover. Whilst undoing the screws
hold the cover securely so that it
does not fall onto the hob.
Lower the cover to remove it.
Replace the light tube or the starter.
Replace the cover and secure in position with the fixing screws.
Replace the primary filter.
16
After sales service
After sales service
In the event of any faults which you cannot easily remedy yourself, please contact:
– Your Miele Dealer
or
– The Miele Service Department,
(see address on the back page)
When contacting the Service Department, please quote the model and serial number of the appliance, both of
which are shown on the data plate,
visible when the grease filter is
removed.
Please note that telephone calls
may be monitored and recorded to
improve our service.
17
Appliance dimensions
Appliance dimensions
18
Appliance dimensions
* DFB lightshield is available as a special accessory.
(Supplied as standard in Australia)
** With this minimum depth, the back
panel of the wall unit housing needs to
be removed (see next page).
The DA 327 i and 329 i can also be
fitted in a 60 cm wide wall housing unit
(see wall unit dimensions for DA 326 i).
Please note that the deflector plate protrudes at the sides. The building in
height of adjacent units must take this
into account.
– The minimum wall unit height required is 460 mm, to ensure that the
exhaust ducting can be fitted to the
exhaust stub without difficulty.
The slot for the active charcoal filter b
must remain accessible if the appliance is being used in recirculation
mode.
19
Appliance dimensions
Building in depth of the wall
unit
The depth required will depend on the
lightshield and where it is positioned.
Appliance with DFB lightshield
(Supplied as standard in Australia)
If the appliance is to be fitted with the
lightshield flush against the front panel
of the wall unit the following building-in
depth A is necessary:
A = min. 273 mm with a 16 mm thick
furniture door
A = min. 270 mm with a 19 mm thick
furniture door
20
Using a lightshield which matches
existing kitchen furniture
If the appliance is to be fitted into a wall
unit in a kitchen run, with a lightshield
to match the existing kitchen furniture,
then a minimum distance B of 275 mm
is required behind the lightshield.
Appliance dimensions
The side spacer C covers a gap of 10
to 70 mm between the rear of the appliance and the wall.
If the wall unit does not have a back
panel and there are no units to the
side of it then a traverse must be
used to provide the unit with extra
stability.
A traverse is available from the
Miele Spare Parts Department in the
appropriate width to suit the wall
unit (Miele DT 60, DT 70 and DT 90).
21
Installation
Installation
Fitting accessories
22
Installation
b 1 hose clip for securing the vent
ducting to the exhaust stub.
c 1 reducing collar
for exhaust ducting ø 125 mm.
8 screws 4.0x16 mm
For securing the runners e
in a 60 cm wide wall unit
or for securing the spacer blocks f,g
in a 70 cm or 90 cm wide wall unit.
d 1 non-return flap
for fitting into the exhaust stub.
e 2 runners
(1 x right, 1x left) to support the appliance in the wall unit.
f 2 spacer blocks (DA 327 only)
for fitting the appliance in a 70 cm wide
wall unit.
g 2 spacer blocks (DA 329 only)
for fitting the appliance in a 90 cm wide
wall unit.
h 2 cover caps (DA 327/329 only)
(1 x right, 1x left) and two inserts i for
covering the support rails when when
fitting in a 70 or 90 cm wide wall unit.
j 2 side spacers
to cover the spaces at the side when fitting in a 60 cm wide wall unit.
k Facia slot
for inserting the active charcoal filter.
6 self-tapping screws
3.5x9.5 mm
2 for securing the light cover n,o
4 for securing the side spacers j.
DA 327, 329 only : 8 more screws for
securing the runners e to the spacer
blocks f,g (when fitting in a 70 or 90
cm wide wall unit)
1 strip with 3 adhesive
sections for attaching a
kitchen furniture lightshield to grip l.
7 screws 3.0x15 mm
2 for attaching the
grip l to the deflector plate; 5 for attaching a kitchen furniture lightshield to
grip l.
l Grip
for the front panel.
m 1 spacer strip
to cover the gap between the rear of
the appliance and the wall.
n 1 light cover
with right and left holders o.
Screwdriver for aligning the furniture
door after the appliance has been built
in.
23
Installation
Safety regulations prohibit the fitting
of this cooker hood over a solid fuel
stove.
The minimum safe distance between the top of the cooker/hob and
the bottom of the cooker hood
should be at least:
– 45 cm above electric cookers /
hobs
– 65 cm above gas cookers / hobs
– 65 cm above a Miele or Imperial
electric open grill.
See “Warning and Safety instructions” for further notes on safe installation.
Fitting procedure
1. Non-return flap (if required)
2. Reducing collar (if required)
3. Fit the runners in the wall unit
4. Fit and align the furniture door
5. Position the appliance in the wall unit
6. Align the height of the appliance
7. Fit the lightshield
8. Align the depth of the appliance
9. Fit the side spacers, the spacer
strip, and the light cover
10. Set up for air extraction or recirculation
11. Connect to the electricity supply
24
Prepare the exhaust stub/ vent socket
for air extraction or recirculation before
installation.
1. Non-return flap
Air extraction with integrated fan
Fit the non-return flap into the vent
socket so that the flaps can open upwards.
(This is not necessary if the ducting
system is already fitted with a non return flap, e.g. wall vent).
Air extraction with external fan
The non-return flap is integrated into
the vent socket.
Recirculation mode
When used in recirculation mode it is
not necessary to fit a non-return flap.
Installation
2. Reducing collar
3. Runners
Air extraction
The appliance is designed for vent
ducting ø 150 mm.
If ø 125 mm is required:
Place the reducing collar supplied
on the vent socket and turn it to secure it in position (see “Connection
for air extraction”).
Recirculation
Place the reducing collar for ø 125
mm on the vent socket as described
previously.
Now fit the two runners into the wall unit.
If the appliance is being installed in a
70 cm or 90 cm wide wall unit the runners are fitted with the spacer blocks.
Position the runners
The positioning will depend on the type
of lightshield being fitted.
Appliance fitted with a DFB lightshield:
(Supplied as standard in Australia)
Draw a vertical line approx. 20 cm
long on both the left and right sides
of the wall unit 100 mm in from the
front edge (see illustration).
25
Installation
Appliance fitted with a lightshield to
match the kitchen furniture:
Fit the runners
(Standard wall unit: 60 cm wide, 16 mm
thick carcase sides)
Hold the runner against the wall unit
ensuring that the lower edge of the
runner is flush with the wall unit. The
first row of screws must be aligned
against the marked line.
The “16 mm" marking should face upwards.
Secure each runner with four 40 x 16
mm screws.
To calculate the position of the lightshield:
Measure the distance “B” from the
front of edge of the wall unit (without
door) and the rear edge of your lightshield.
Then draw a vertical line approx. 20
cm long on both the left and right
side panels of the wall unit for dimension "C".
If dimension “B” is less than 20 mm,
dimension “C” will be 100 mm.
If dimension “B” is between 20 and 40
mm, dimension “C” will be 124 mm.
If the appliance is fitted into a Miele kitchen furniture wall unit and fitted with a
lightshield to match, the necessary drill
holes will already be provided in the
wall unit.
26
Exception: Please refer to the notes
under “Special fitting instructions” at
the end of the “Installation” section for
instructions on fitting the appliance into
a wall unit with 19 mm thick carcase
sides or into a 70 cm or 90 cm wide
wall unit.
4. Fit the furniture door
Before building in the
appliance, fit and
align the wall unit furniture door.
Use the special tool
supplied, if you need
to re-align the furniture door after the appliance has been
built in and the
hinges are no longer accessible.
Installation
5. Position the appliance in
the wall unit
Lift the cooker hood into the wall
unit, making sure that the supports
on the cooker hood are sitting on the
runners in the wall unit. Push it into
the wall unit as far as it will go.
The supports will slide under the antitip device b.
Insert the adjusting screws c on the
runners through the holes in the supports.
Use a small screwdriver to push retainer d down over adjusting screw
c.
6. Align the height of the
appliance
Use screw e to align the height.
Now align the appliance so that it is
horizontal.
Turning screw e clockwise, raises the
appliance upwards, turning it anticlockwise lowers it.
Close the unit door and check that
the deflector plate goes in and out
smoothly. If necessary make more
adjustments as above.
Fit the lightshield before aligning the
depth.
27
Installation
7 a. Fitting a DFB
lightshield
Follow the fitting instructions supplied
with the lightshield.
(Supplied as standard in Australia)
7 b. Fitting a lightshield to
match the kitchen furniture
Fit the grip into the openings on the
deflector plate.
Australia: The stainless steel lightshield DFB is supplied as standard.
If you wish to fit a lightshield to
match your kitchen furniture the stainless steel lightshield has to be taken
off. Proceed as follows:
1. Remove both screws from the grip.
2. Take the grip off.
3. Loosen the 5 fixing screws to detach the lightshield from the grip.
The furniture lightshield is then fitted
to the grip as described in the next
section.
28
Secure the grip in position with
screws (3.0 x 15 mm) fitted into the
underside of the deflector plate.
Stick the three lengths of double
sided adhesive tape to the grip.
Remove the protective backing.
Installation
8. Align the depth of the
appliance
Stick the furniture lightshield to the
grip in the position required.
Dismantle the grip again and secure
the lightshield to the grip using five
3.0 x15 mm, two at either side and
one in the middle.
Fit the lightshield back on to the appliance again.
To move the appliance further out of
the wall unit:
Loosen screws c and tighten
screws f.
Tighten screws c again to secure it
into position.
To move the appliance further into
the wall unit:
Loosen screws f and tighten
screws c.
Tighten screws f again to secure it
in position.
Check the alignment again by pulling the deflector plate out and pushing it back in again.
29
Installation
9 a. Fit side spacers at the
sides of the appliance
9 b. Spacer strip
for the rear of the appliance
(Standard wall unit 60 cm wide)
Measure the gap “T” to be covered
between the rear of the appliance
and the wall.
The side spacers cover the gaps between the sides of the appliance and
the wall unit.
Before fitting the side spacers, use a
knife to make a cut-out in the side
spacer for the appropriate side of
the wall unit to accommodate the
wall unit hingeing.
Use a knife to trim the spacer strip
supplied to measurement “T”.
Screw the side spacers to the housing with 3.5 x 9.5 mm screws and
press them in at the sides.
Exception: Please refer to the notes
under “Special fitting instructions” at
the end of the “Installation” section for
instructions on fitting the appliance into
a wall unit with 19 mm thick carcase
sides or into a 70 cm or 90 cm wide
wall unit.
30
Stick the spacer strip to the underside of the appliance.
Turn the side cover caps upwards
and press into position.
Installation
9 c. Light cover
Replace the primary filter:
Pull the deflector plate out slightly.
Tilt the primary filter at the front down
slightly and pull it out towards the
front.
Make sure that the red plastic
guides are at the front and facing upwards.
Fit the primary filter into the extended deflector plate from below
and hold it in position.
Insert the two holders on to the sides
of the light cover.
Push the filter gently upwards and
push the deflector plate in. The filter
will slide into the holders.
Secure the light cover using self-tapping screws 3.5 x 9.5 mm.
31
Installation
10 a. Set up for vented
extraction
10 b. Set up for recirculation
connection
If site conditions are not suitable for the
cooker hood to be used for air extraction the appliance must be connected
for recirculation.
The following parts, available through
your Miele Dealer or from the Miele
Fit the panel supplied into the slot for
the active charcoal filter.
Secure the ventilation ducting over
the vent socket on the cooker hood
using a hose clip.
Complete venting installation. (See
“Connection for air extraction”).
Spare Parts Department are required
for operating the appliance in recirculation mode:
– Conversion kit for recirculation mode
(ø125 mm): exhaust grille, hose,
hose clip
– Active charcoal filter (see “Technical
data”)
Connection
When fitting the cooker hood in a wall
unit the exhaust grille c has to be fitted
in the top of the unit. The exhaust stub
(vent socket) b and the exhaust grille
c are joined together with a pipe or
flexible duct cut to size d.
32
Installation
If the front of the unit is ceiling height
then an appropriate cut-out must be
made in the front panel e .
When fitting the ventilation grille make
sure that the slats in the grille point towards the centre of the room and not towards a wall or the ceiling.
Special fitting instructions
Fitting into wall unit with 19 mm
thick carcase sides
The runners have to be adapted as
shown above.
The slot for the active charcoal filter is
located on the front of the appliance.
Install the active charcoal filter (see
“Cleaning and care”).
11. Electrical connection
Refer to the notes in “Electrical connection” and “Warning and Safety
instructions” before connecting to
the electricity supply.
Screw the runners to the wall unit
with the "19 mm" marking facing upwards as shown above.
EXT model cooker hoods are designed for use with an external fan,
i.e. the fan is fitted outside the room
in a position of your choice.
Electrical connection is made via a connecting lead with plug and coupling.
Separate fitting instructions are supplied with the external fan.
33
Installation
Installing in a 70 or 90 cm wide wall
unit:
The runners are fitted to spacer blocks.
When fitted in a 70 or 90 cm wide wall
unit the runners are fitted with the cover
caps supplied.
70 cm wide wall unit
Cut the inserts to the required depth
and fit into the sides of the cover
caps.
On units with 19 mm thick sides the
cover caps for the runners must be
trimmed using a knife along the
groove.
90 cm wide wall unit
Screw the spacer block to the wall
unit using 4.0 x 16 mm screws with
the lower edge flush with the wall
unit. The first row of screws must be
aligned to the marked line.
Screw the runners to the spacer
block using the 3.5 x 9.5 mm self tapping screws.
34
Installation
Fit the cover caps to the runners on
both sides of the unit.
Conceal the 4 drill holes in the housing with the 3.9 x 9. 5 mm screws.
35
Connection for air extraction
Connection for air extraction
Danger of toxic fumes.
Please heed the “Warning and
safety instructions” to avoid the
danger of toxic fumes.
The cooker hood should be installed according to local building
regulations. Seek approval from the
building inspector where necessary.
– If the exhaust air is to be ducted into
the open air the installation of a telescopic wall vent is recommended.
– All ducting, pipework and fittings
must be of non-flammable material.
– The extraction ducting should be as
short and straight as possible.
– To ensure efficient air extraction the
diameter of the exhaust ducting
should not be less than 150 mm.
If extraction ducting with a diameter
of less than 150 mm or flat ducting
were to be used the noise level of
the cooker hood would increase
and extraction would be less efficient.
Only reduce the diameter of the ducting if absolutely necessary, e.g.
where narrower ducting has already
been installed.
– Only use wide radius bends. Tight
bends reduce the air throughput of
the cooker hood.
– Only use smooth pipes or flexible
hoses made from non-flammable materials for extraction connection.
– When ducting is horizontal it must be
laid to slope away at at least 1 cm
per metre to ensure no condensate
drains into the appliance.
36
– If the exhaust air is to be ducted into
a vent flue the ducting must be directed in the flow direction of the flue.
Important
If the exhaust ducting is to run
through rooms, ceiling space etc.
where there may be great variations
in temperature between the different areas the problem of sweating
or condensation will need to be addressed.
The exhaust ducting will need to be
suitably insulated.
Electrical connection
Electrical connection
Electrical connection
Important
All electrical work should only be carried out by a suitably qualified and competent person in accordance with national and local safety regulations.
The wires in the mains lead are coloured in accordance with the following
code:
Green/yellow = earth
Blue
= neutral
Brown
= live.
UK, IRL, NZ, ZA: The cooker hood is
supplied for connection to an a.c.
230 V single phase 50 Hz supply.
AUS: The cooker hood is supplied for
connection to an a.c. single phase 240
V, 50 Hz supply.
The data plate gives the necessary
data for connection. This is visible
when the grease filter has been
removed.
For U.K.: Connection should be made
either by a double pole fused spur connection unit, or a fused plug and a suitable switched socket. The On-Off
switch should be easily accessible
after the appliance has been built in.
When switched off there must be an allpole contact gap of 3 mm in the switch
(including switch, fuses and relays according to EN 60 335).
If the socket is not accessible after installation (depending on country) an additional means of disconnection must
be provided for all poles.
For extra safety it is advisable to install
a residual current device (RCD) with a
trip current of 30 mA (in accordance
with DIN VDE 0664).
If the appliance is to be connected via
a plug and socket, please note the following:
As the colours of the wires in the mains
lead of this appliance may not correspond with the coloured markings
identifying the terminals in your plug,
proceed as follows:
The wire which is coloured green and
yellow must be connected to the terminal in the plug which is marked with the
letter E or by the earth symbol z or coloured green or green and yellow.
The wire which is coloured blue must
be connected to the terminal which is
marked with the letter N or coloured
black.
For U.K., ZA:The wire which is coloured
brown must be connected to the terminal which is marked with the letter L or
coloured red.
For Australia / New Zealand: The wire
which is coloured brown must be connected to the terminal which is marked
with the letter A or coloured red.
WARNING:
THIS APPLIANCE MUST BE
EARTHED
37
Electrical connection
Non-rewireable plugs BS 1363 (UK)
If this machine or appliance is fitted
with a non-rewireable plug, the following information applies:
If the socket outlets are not suitable for
the plug supplied with this product, it
must be cut off and an appropriate
plug fitted. The fuse carrier and the
fuse should be removed from the old
plug and disposed of. The plug cut
from the flexible cord should then be
disposed of, and on no account be inserted into any socket elsewhere in the
house (electric shock hazard).
The fuse cover must be re-fitted when
changing the fuse and if the fuse cover
is lost the plug must not be used until a
suitable replacement is obtained.
The colour of the correct replacement
cover is that of the coloured insert in
the base of the plug (as applicable to
the design of plug fitted).
The correct fuse rating of the replacement fuses that are ASTA approved to
BS 1362 should be fitted. Replacement
fuse covers may be purchased from
your local electrical suppliers or Service agent.
38
Technical data
Technical data
Rated load
– DA 326 i. . . . . . . . . . . . . . . . . 215 W
– DA 327 i. . . . . . . . . . . . . . . . . 213 W
– DA 329 i. . . . . . . . . . . . . . . . . 216 W
Lighting
– DA 326 i, DA 326 i EXT . . . 1 x 15 W
– DA 327 i, DA 327 i EXT . . . 1 x 13 W
– DA 329 i, DA 329 i EXT . . . 1 x 16 W
Voltage
UK, IRL, NZ, ZA . . . . . . . . . . . . . 230 V
AUS . . . . . . . . . . . . . . . . . . . . . . 240 V
Frequency . . . . . . . . . . . . . . . ~ 50 Hz
Fuse rating (UK) . . . . . . . . . . . . . 13 A
Fuse rating (IRL) . . . . . . . . . . . . . 10 A
AUS, NZ:
Plug rating . . . . . . . . . . . . . . . . . . 10 A
Test marks . . . . . . . . . Electrical safety
. . . . . . . . . . . . . . . . . . . . . C-Tick Mark
Electrically suppressed
according to AS/NZS 1044
Fan performance
Extraction power according to EN
61591
Extraction system ø 150 mm:
Level I . . . . . . . . . . . . . . . . . . .
Level II . . . . . . . . . . . . . . . . . . .
Level III . . . . . . . . . . . . . . . . . .
Intensive level . . . . . . . . . . . . .
200 m3/h
310 m3/h
440 m3/h
640 m3/h
Extraction system ø 125 mm:
Level I . . . . . . . . . . . . . . . . . . .
Level II . . . . . . . . . . . . . . . . . . .
Level III . . . . . . . . . . . . . . . . . .
Intensive level . . . . . . . . . . . . .
190 m3/h
300 m3/h
400 m3/h
590 m3/h
Unrestricted. . . . . . . . . . . . . . . 690 m3/h
Recirculation mode with active charcoal filter:
Level I . . . . . . . . . . . . . . . . . . .
Level II . . . . . . . . . . . . . . . . . . .
Level III . . . . . . . . . . . . . . . . . .
Intensive level . . . . . . . . . . . . .
190 m3/h
300 m3/h
410 m3/h
550 m3/h
Active charcoal filter:
Miele DKF 8 - Art. Nr. 28.9961.34
For EX models the rated load and extraction power will depend on the type
of external fan fitted.
39
Alteration rights reserved / 44 / 002
This paper consists of cellulose which has been bleached without the use of chlorine.
GB - 2700