Craftsman 247.797851 Owner`s manual

OWNER'S
ANUAL
MODELNO,
247.797851
®
Caution:
Read and Follow
AH Safety Rules
and Instructions
Before Operating
This Equipment
5 HORSEPOWER
3 CUTTnNG STAGE
MULCHHNG AND BAGGnNG
CH_PPER-SHREDDER
Assembly
Operation
Maintenance ;
Service and Adjustment
Repair Parts
SEARS, ROEBUCKAND CO., CNcago, iL
60684 U.S,A.
SAFETY
WARNING',
TO REDUCE
SAFETY
INSTRUCTIONS.
PERSONAL
INJURY.
RULES
THE POTENTIAL
FOR ANY INJURY,
FAILURE
TO COMPLY
WITH THE
TRAINING
e Read this owner's manual carefully in its entirety before
attempting to assemble or operate this machine Be cornpletely familiar with the controls and the proper use of this
machine before operating it Keep this manuat in a safe
place for future and regufar reference and for ordering
replacement parts
• Children must never' be allowed to operate this equipment
o No one should operate this unit while intoxicated or while
taking medication that impairs the senses or reactions
• This equipment should never be operated in the vicinity
of children, pets or other persons
o Never run your machine tn an enclosed area as the exhaust from the engine contains carbon monoxide, which
is an odorless, tasteless and deadly poisonous gas
Never place your hands or any pad of your body or ctothing
inside the feeding chamber, discharge chute, or near any
moving part while the machine or engine is running
• if it is necessary for any reason to inspect or repair the
feeding chamber or any part of the machine where a moving part can come in contact with your body or clothing,
stop the machine, allow it to coot, disconnect the spark
plug wire from the spark plug and move it away from the
spark plug before attempting such inspection or repair
PREPARATION
e Wear safety gtasses provided with your unit while
operating the chipper-shredder
to prevent injury from any
material which may be ejected out el the openings
• Wear proper appale] Avoid wearing loose fitting clothing
Wear gloves when handling material
® HANDLE GASOLINE WITH. CARE as it is an extremely
flammable fuel
• Check the fuel before starting the engine Do not fill the
fuel lank indoors, while the engine is running, or while the
engine is still hot Turn the unit off and let the engine cool
before refueling
• Fuel your chipper-shredder in a clean area. Do not smoke
while refueling
o Fuel tank cap must be secure at all times except during
refueling,
o Avoid spilling gasoline or oil Wipe the unit clean of any
spilled fuel or oil
@ Store fuel and oil in approved containers, away from heat
or open flame, and out of reach of children
• This machine should be operated only upon a level
surface.
e Assure that eli screws, nuts and bolts and other fasleners
are properly secured
OPERATION
e When feeding shreddable material into this equipment, be
extremely careful that pieces of metal, rocks, bottles, cans
or other foreign objects are not included Personal injury
or damage to the machine could result
COMPLY WITH
INSTRUCTIONS
THE FOLLOWING
MAY RESULT IN
e If the cutting mechanism strikes any toreign object or if
your machine should stall making an unusual noise or
vibration, immediately stop the engine, disconnect the
spark plug wire from the spark plug and move it away from
the spark ptug Allow the machine to stop and take the
foliowing steps:
Inspect for damage
Replace or repair any damaged parts
Check for any loose parts and tighten to assure continued
safe operation
I The engine must be kept clean of debris and other accumulations
e Do not allow an accumulation of processed material to
buiId up in the discharge area as this will prevent proper
discharge and can result in kick-back trom feed opening
e Never p_ace your hands or any other part of your body or
clothing inside the feeding chamber, discharge chule or
near any moving part while the engine is running
e Keep all guards and deflectors in place and in good work,ing condition toassure continued safe operation
• Always stand clear of the discharge area when operating
this machine
e Keep your face and body back from the feed opening to
avoid accidental bounce back ot any material
e Do not over4each Keep proper balance and footing at all
times
o The engine governor settings on your machine must not
be altered, changed, or tampered with The governor controls the maximum sate operating speeds and protects the
engine and all moving paris _om damage caused by
overspeed
,o Do not transport machine while engine is running
o Do not operate engine if air cleaner or cover directty over
carburetor air intake is removed, except for adjustment
Removal of such paris could create a fire hazard
MAINTENANCE AND STORAGE
o When this equipmenl is stopped tor servicing, inspection,
storage or to change an accessory, make sure the spark
plug wire is disconnected from the spark plug and moved
away from the spark plug The machine should be aliowed
to cool down before making such inspection, adiustments+
service, etc, Maintain your machine with care and keep
it clean for the best and continued safe operation
• Do not use flammable solutions to clean the air titter
• When not in use, your machine should be stored out of
the reach ol children Keep where gasoline fumes wilt not
reach an open flame or spark For tong periods of storage,
refer to the "Storage '' section of this manual
LOOK FOR THIS SYMBOL TO POINT OUT
IMPORTANT SAFETY PRECAUTIONS.
l'l"
MEANS--ATTENTION[!!
BECOME ALERT!!!
YOUR SAFETY tS INVOLVED+
CONGRATULATIONS
on your purchase ot a Sears
Craftsman
Chipper-Shredder
It has been designed,
engineered and manufactured to give you the best possible
dependability and performance
PRODUCT
Should you experience any problem you cannot easily
remedy, please contact your nearest Sears Service
Center/Department
We have competent, wel!4rained technicians and the proper loots to service or repair this unit
Horsepower:
Please read and retain tMs manual The instructions wilt
enable you to assemble and maintain your chipper-shredder
properly Always observe the "SAFETY RULES "
Fuel Capacity:
SPECUFRCAT ONS
50
Displacement:
12 57 cu in
3 Quarts
Spark Plug (Gap 030 in ):
Champion
J19LM or
Equivalenl
MODEL
NUMBER
247,797851
Magnetron e Ignition Air Gap:
SERIAL
0!25 in
NUMBER
DATE OF
PURCHASE
THE MODEL AND SERIAL NUMBERS WILL BE FOUND
ON A LABEL ATTACHED TO THE FRAME OF THE
CHIPPER-SHREDDER
YOU SHOULD RECORD BOTH SERIAL NUMBER AND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE
CUSTOMER
MASNTENANCE AGREEMENT
A Sears Maintenance Agreement is available on this
product Contact your nearest Sears s{0re for details
RESPONS BIL TRES
e Read and observe the safety rules
e Follow a regular schedule ir_ maintaining, caring for and using your chipper-shredder
e Follow the instructions under "Maintenance"
and "Storage" sections of this Owner's Manual
WARRANTY
ONE YEAR UMITED WARRANTY ON CRAFTSMAN GAS [;HnPPER.,SHREDDER
For one year from the date of purchase, when this Craftsman Chipper-Shredder is maintained, lubricated and
tuned up according to the instructions in the owner's manual, Sears will repair, free of charge,, any delect in
material and workmanship
If this Craftsman Chipper-Shredder is used for commercial
30 days from the date of purchase
or rental purposes,
this warranty applies for only
This warranty does not cover:
e Expendable items which become worn during normal use, such as blades, chipper blades, flails, air cleaners,
spark plugs and catcher bags
o Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to
maintain the equipment according to the inslructions contained in the owner's manual
WARRANTY SERVICE IS AVAILABLE BY RETURNING THE CRAFTSMAN CHIPPER-SHREDDER TO THE
NEAREST SEARS SERVICE CENTER/DEPARTMENT IN THE UNITED STATES THIS WARRANTY APPLIES
ONLY WHILE THIS PRODUCT IS tN USE IN THE UNITED STATES
This warranty gives you specific legal rights, and you may also have other rights which may vary from state
to state
SEARS,
ROEBUCK
AND
CO,
Department
731CR-W,
Sears
Tower,
Chicago,
IL 60684
TABLE
OF CONTENTS
2
3
,3
3
4
5, 6
7-10
10, 11
SAFETY RULES
PRODUCT
SPECIFICATIONS
CUSTOMER
RESPONSIBILITIES
WARRANTY
INDEX
ASSEMBLY,
OPERATION
MAINTENANCE
STORAGE
SERVICE AND ADJUSTMENT
SERVICE RECOMMENDATIONS
TROUBLE SHOOTING,
REPAIR PARTS--CHIPPER_SHREDDER
REPAIR PARTSmENGINE
PARTS ORDERINGtSERVlCE
12
13-t5
15
16
17, 18
19*23
Back Cover
INDEX
A
O
Adjustments:
Carburetor
Engine Speed ,o
Assembly Instructions:
Catcher Bag ....
Chute Crank Deflector
Hopper Assembly
Catcher' Bag
t4
15
6
6
6
6
C
6
7
3
Catcher Bag
Controls
Customer Responsibiiiiies
E
Engine:
Maintenance
Starting ....
Stopping,
Storage .....
9,10
R
Release Bar
RepairlReplacement
Parts
Responsibilities, Customer'
.7
17-23
3
8
S
Satety Rules
Sharpening
Service Recommendations
,
Spark Plug
.....
Specifications
....
Storage
.......
2
13, 14
15
11
,3
12
T
I0,
11
8
_9
Table of Contents
Trouble Shooting
U
, I2
F
Fue!
, k ,
8
.....
13
5
Unclogging
Unpacking
W
L
Lubrication
Oil
Operating Tips
.......
10
Warranty
M
Maintenance:
Agreement
Engine .....
Chipper-Shredder
,,.
....
10, 1t
t0
WARNING:
This unit is equipped with an internal combustion
engine and should not be used on or near any unimproved forest-covered,
brush-covered
or grass-covered
land unless the engine's exhaust system is equipped with
a spark arrester meeting applicable
local or state laws (if any) tf a spark arrester is used, it should be maintained
in effective working order by the operator,
tn the State of California
the above is required by law (Section 4442 of the California
Public Resources
Code)
Other states may have similar laws, Federal laws apply on federat lands
A spark arrester for the muffler (see
page 23) is available
through your Sears Authorized
Service Center
ASSEMBLY
IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL After assembly, see operation section of
this manual for proper fue! and engine oil recommendations
Hex Lock
ut 5116-18
Thread
Washer
5fi6" I°D.
_-------5116-'t8
INSTRUCTIONS
Hex Bolt
x 8-3/8"
NOTE: To determine right and left hand sides of your
chipper-shredder, stand behind and face the hopper
(engine is at the front of the unit)
Your chipper-shredder has been completely assembled
at the factory, excepl for the hopper assembly (hopper
hood and upper guide extension have been subassembled), upper guide assembly, chute defleclor and
the catcher bag The hardware pack and safety glasses
are also included in the carton
Long
The hardware pack contains the parts shown in figure
1 (shown full size).
TOREMOVE
CHIPPER-SHREDDER
FROMCARTON
Cut the corners of the carton, Remove air packing inserts, Rol! chipper-shredder out of the carton, Make certain al! parts and literature have been removed before
the carton is discarded
Hand
Knobs
TOOLS REQUIRED FOR ASSEMBLY
(!)
(1)
(2)
(2)
Cupped Washers
5/16" I.D.
Phitfps Screwdriver
Straight Blade Screwdriver
1/2" or Adjustable Wrenches
7/16" or Adjustable Wrenches
Hex Bolt !/.-20
x 4" Long
i
Spacers_
1/4" I,,D.
Lock Washer---_(f'_
V4" I.D
_--_-_----_
t_____J
_
Hex Nut
V,_-20Thread
._ Machine Screws
t/4-20 x 1/2" Long
Hex Lock Nuts
1/4
,.20 Thread
FIGURE
1.
5
HOWTOSET-UPYOUR CHIPPER.,SHREDBE£
He× Bolt
Long
IS DISCONNECTED AND MOVED AWAY
MAKE CERTAIN THE SPARK PLUG WIRE
FROM "['HE SPARK PLUG BEFORE ASSEMBLiNG THE CHIPPER-SHREDDER.
Chute
Deflector
Lock
Washer
Hex Nut--'---
ATTACHING THE CHUTE DEFLECTOR
® Place one fiat washer 1/4" I D., then one spacer t/4"
1.D on hex bolt 4" tong
Hand.
® Place chute deflector in position on the discharge
opening, on the left side of the chipper-shredder
® Insert hex bolt through hinge on chute deflector and
-*-----housing
(spacer fits inside of hinge) See figure 2
® Place second spacer t14" ID over he× bolt, inside
other part of hinge. Secure with 114" l D. flat washer,
lock washer and hex nut Tighlen securely
Knob "_
FIGURE 2.
Stop
Washer
e Secure both sides of chute deflector to housing using hand knobs and cupped washers 5/16" I.D.
(cupped side of washers go against chute deflector),
ATTACHING
Upper
Guide
Assembly
Release
Bar
Bolt
8.318" Long
Flat Washer
Hex Lock Nut
Hopper
Pivot
Assemble
This
Truss Screw and
Nut
ATTACHING
Upper
Guide
Extension
Bar
Remove Truss
Screw and Nut
Guide
Assembly
FIGURE
Place upper guide assembly in position on frame, making certain edges of the upper guide assembly are
underneath stop washers, and the release bar is in the
-.,,---slots See figure 3. Insert hex bolt 8-3t8" long through
upper guide assembly and frame Secure with fiat
washer 5/16" I D and hex lock nut
NOTE: Make certain upper guide assembly can pivot
by pulling up on release bar and lowering upper guide
assembly. I! necessary, loosen hex lock nut a turn or
two Put the upper guide assembly back into the raised
position
Hopper Assembly
Rat®use
THE UPPER GUIDE ASSEMBLY
4,,
Drawstring
/
THE HOPPER ASSEMBLY
Your chipper-shredder has been shipped with the upper
guide extension attached to the hopper assembly. See
._---figure 4 Attach the hopper assembly to the upper guide
assembly as follows Be certain to place heads of all
truss machine screws inside of hopper assembly
e Remove one truss machine screw and nut from each
side of hopper assembly as shown in figure 4 Push
hopper' pivot door down inside lower part of hopper as you pface hopper assembly (both pieces) inside upper guide assembly.. Replace truss screws
and nuts iust removed, using the front upper hole
in assembly as shown in figure 4, one on each side
Tighten finger tight only.
© Place the six truss machine screws and nuts found
in hardware pack in the remaining holes of hopper
assembly, alternating sides of the unit and tightening finger tight only,
ger
e After assembling
securely
ATTACHING
FIGURE
5.
all eight screws, tighten them
'THE CATCHER
BAG
_._---Your chipper-shredder is equipped with a catcher bag
to catch the shredded material
e To attach the bag, place the opening of the bag over
the chute deflector
so it completely covers the chute
opening Depress the plunger on the drawstring, pull
on the drawstring
until the bag is tight around the
chute opening. Release plunger to lock it into posi,tion See figure 5
OPERATION
KNOW YOUR C;HtPPER-SHREDDER
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHIPPER-SHREDDER
Compare the illustrations with your chipper-shredder to familiarize yourself with the location of various controls
and adjustments Save this manual for future reference
Hopper
Assembly
f
•
Release
Otl Fill
Dipstick
....
f_"%
'
Chipper
Chute
S
Pluc
Chute
Deflector
Choke
Catcher
Bag
Throttle
Control
Handle
FIGURE
6o
i
........
MEETS ANSI SAFETY STANIgARBS
Sears chipper-shredders
conform to the safety standards
OPERATINGCONTROLS(See
RELEASE BAR--Used
raising or lowering,
figure
of the American National Standards
Institule
6)
to release the hopper when
CHOKE LEVER--Used to enrich the fue! mixture in the
carburetor when starting a cold engine
STARTER
engine
HANDLE--Used
to manually
THROTTLE CONTROL--Controls
stops the engine
BEFORE USING YOUR CHIPPER-SHREDDER, AGAIN REFER TO THE "SAFETY
PAGE 2 OF THIS MANUAL ALWAYS BE CAREFUL,
RULES"
start the
engine speed and
AS SHOWN ON
The operation ol any chipper-shredder can result in toreign objects being lhrown into
the eyes, which can result in severe eye damage, Always wear the safety glasses provided with the chipper-shredder or eye shields belore chipping or shredding, or while
performing any adjustments or repairs, We recommend Wide Vision Safety lvlask for
over spectacles or standard glasses available at Sears Retail or Catalog Stores
BEFORE:STARTING .... :........................
........
tion of acids
GAS AND OIL FILL-UP
NOTE: ENGINE IS SHIPPED WITHOUT OIL FILL
CRANKCASE WITH OIL BEFORE STARTING BE
VERY CAREFUL NOT TO ALLOW DIRT TO ENTER
THE ENGINE WHEN CHECKING OR ADDING OIL OR
FUEL
Recommended
i
SAE Viscosity
]I
A,
I I
__.,
5W30 .....
0°
32 °
3oor l ow3o
T--F" I
_
60 °
Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may result
NOTE' USE CLEAN OIL AND FUEL STORE IN APPROVED, CLEAN, COVERED CONTAINERS
USE
CLEAN FILL FUNNELS.
1 ] 1I ] |l
I ....
I..............
1 ],I-
- 20 °
Grades
during sto[age_ Acidicgas can damage
the fuel system of an engine while in storage To avoid
engine problems, the fuel system should be empty
before storage for 30 days or longer Refer to "Storage"
section of this manual for details Use fresh fuel each
season
80 °
Spark
11]
Oil
100 °
Fill
Plug,
Wire,,
and \
Muffler
TEMPERATURE RANGE EXPECTED BEFORE NEXT
OIL CHANGE. ALL OILS MUST BEAPI
SERVICE
CLASSIFICATION SD, SE OR SF
o Fill engine with oil as follows. Remove oil fill dipstick
See figure 7 With chipper-shredder level, use a funnel to fill engine with oil to FULL mark on dipstick
Capacity is approximately 1t/4 pints Be careful not
to overfill. Tilt chipper-shredder toward the left (from
behind the hopper), then re-teve{ Check oil level
Refill to FULL mark on dipstick if necessary Replace
dipstick and tighten
Dipstiik
__
t
FIGURE 8,
Oil
Fill----*
Dipstick
FIGURE
7_
o Remove fuel cap and fill fuel tank, See figure 8 Use
fresh, clean, unleaded automotive gasoline. Capacity is 3 quarts. Replace fuel cap,
_
t/2
INCH OFDOTOP
TANKTHAN
TO
WARNING:
NOT OF
FILLFUEL
CLOSER
PREVENT SPILLS AND TO ALLOW FOR
FUEL
EXPANSION.
IF GASOLINE
IS
ACCiDENTLY
SPILLED,
MOVE CHIPPERSHREDDER
AWAY
FROM
AREA
OF
SPILL. AVOID CREATING
ANY SOURCE
OF IGNITION UNTIL GASOLINE
VAPORS
HAVE DISAPPEARED.
Caution:
Experience
indicates
that alcohol blended
fuels (called gasohol or using ethanol or methanol) can
attract moisture which leads to separation
and forma-
TO START ENGINE
THAN
THE OPERATOR
IS STANDING
WARNING:
BE SURE NO ONE OTHER
NEAR THE CHIPPER-SHREDDER
WHILE
STARTING
OR OPERATING_
DO
NOT
OPERATE
THIS
CHIPPERSHREDDER
UNLESS
THE CHUTE DEFLECTOR
HAS
BEEN
PROPERLY
INSTALLED
AND IS SECURED
WITH THE
HAND KNOBS.
• Attach spark plug wire and rubber boot to spark
plug See figure 8..
• Place the throttle control lever in FAST position, See
figure 9
a Move choke fever to CHOKE position.
• Grasp starter handle (see figure 9) and pull rope out
slowly until engine reaches start of compression cycle (rope will pul! slightly harder at this point) Let
the rope rewind slowly.
NOTE: A noise will be heard when finding the start of
the compression cycle. This noise is caused by the flails
and fingers which are part of the shredding mechanism
falling into place, and should be expected
•
Pull rope with a rapid, continuous,
1oil arm stroke
Keep a firm grip on start handle
Let rope rewind
slowly
Do not tet starter handie snap back against
starter
e Repeat preceding two instructions until engine fires
When engine starts, move choke lever on engine
halfway between CHOKE and RUN
NOTE: If engine does not tire after three
move choke lever halfway between CHOKE
position
and try again
Chok?
See figure
attempts,
and RUN
9
jLZ "_
oFF
Throttle
FIGURE
The chipper-shredder
methods o1 operation
is designed lot three different
@ Leaves and small branches up to 1/2" diameter can
be fed into the hopper assembly when it is in the
raised position
See figure !0 If it becomes
necessary to push material into the chippershredder, use a small diameter stick--NOT YOUR
HANDS The stick should be small enough that it
will be ground up if gets into the impeller assembly
WARNING:
DO NOT PUT MATERIAL
LARGER THAN 1/2" IN DIAMETER INTO
THE HOPPER ASSEMBLY, MATERIAL UP
TO A MAXZIMUM OF 3" IN DIAMETER
MATERIAL
MAY BE FED INTO THE
CHIPPER CHUTE. DO NOT ATTEMPT TO
SHRED
OR CHIP ANY MATERIAL
LARGER
THAN
3" IN DIAMETER.
PERSONAL INJURY OR DAMAGE TO
THE MACHINE COULD RESULT°
Control
9..
e Move throttle contro! to IDLE position for a few
minutes warm-up Move choke lever 1o RUN position as engine warms up
NOTE: In order to idle smoothly, a new engine may require 3 to 5 minutes running above stow idle speed
idle speed has been adjusted to be correct after this
break-in period
TO STOP ENGINE
o Move throttle control lever to STOP position
figure 9.
See
o Disconnect spark plug wire and move away from
spark plug to prevent accidental starting while equipment is unattended.
HOW TO USE YOUR CHIPPER-SHREDDER
Do not attempt to shred or chip any material other than
vegetation found in a normal yard (leo, branches,
leaves, twigs, etc.)
&
WARNING:
THE CHIPPER-SHREDDER
DISCHARGES
MATERIALS
WITH CON*
SIDERABLE
VELOCITY,
KEEP
AWAY
FROM THE AREA AROUND THE CHUTE
DEFLECTOR,,
ALWAYS
STOP
THE
ENGINE AND DISCONNECT
THE SPARK
PLUG WIRE WHEN REMOVING
OR ATTACHING
THE BAG WHEN CHANGING
CONTAINERS
OR WHEN REMOVING THE
SHREDDED
MATERIAL,
WEAR SAFETY
GLASSES
AND
GLOVES
WHENEVER
USING YOUR CHIPPER-SHREDDER.
opper
Assembly
FIGURE 18.
Leaves and small twigs can be raked into the hopper assembly when the hopper assembly is lowered
to the ground See figure 11 Small branches up to
tt2" diameter can also be fed into the hopper
assembly in this position See figure 12
• Bulky material, such as stalks or heavy branches,
up to 3" in diameter, should be fed into the chipper chute See figure 14
A
CHUTE DOOR IS CLOSED WHEN NOT IN
WARNING: MAKE CERTAIN THE CHIPPER
USE.
3" Maximum
Diameter
No Larger
1/2" Diameter
FIGURE 12.
® To lower the hopper assembly, use one hand to
grasp the handle at the top of the hopper assembly
and lift slightly. Pull up on the release bar, and lower
tile hopper assembly to the ground Release the bar
See figure 13.
Chipper
Chute
Hopper
Assembly
FIGURE 14,
IMPORTANT: There is a flail screen located inside the
housing in the discharge area. If the flail screen
becomes clogged, remove and clean as instructed in
the Service and Adjustments section on page 13. For
best performance, it is important to keep the shredding
blade and the chipper blades sharp If the composition
of the material being discharged changes (becomes
Stringy, etc.) or if the rate at which the material is
discharged slows down considerably, it is likely that the
shredding bfade andtor chipper blades are dull and
need to be sharpened ot" replaced Refer to Service and
Adjustments section, page t3.
Release
Bar
FIGURE 13.
MAINTENANCE
GENERALRECOMMENDATIONS
ENGINE
• Periodically check atl fasteners and be sure they are
tight,
LUBRICATION
• Follow the Service Recommendation
Check engine oil level regularly--approximately
every
five hours of operation and before each usage Stop
engine and wait several minutes before checking oi!
level With engine level, the oil must be to FULL mark
on dipstick (refer to figure 7), Change engine oil after
the first five hours of operation, and every twenty-five
hours thereafter.
Schedule on
page 15..
CHIPPER-SHREDDER
e Drain oil while engine
LUBRICATION
Lubricate the pivot points on the release bar, guide extension assembly, chute deflector and chipper chute
once a season using a light oil
Remove oil drain
chipper-shredder,
tainer
10
is warm,
plug
Refer to figure 7 Tip the
and catch oil in a suitable con-
Whenengineisdrainedofalloil.replacedrainptug
securely
....
e Refillwithfreshoil Above32°, useoil labeledSAE
30Wor 10W30Below32°, useoil labeled5W20
Capacityis approximately
1V_,pints Refer to "Gas
and Oil Fill-Up"
e Replace
on page
is not recommended
fuel system
dipstick
contarninate
the
WARNING: PERIODICALLY CLEAN MUF_
FLER AREA TO REMOVE ALL GRASS,
DIRT AND COMBUSTIBLE DEBRIS
AIR CLEANER
The air cleaner prevents damaging dirt, dust, etc, from
entering the carburetor and being forced into the engine
and is important to engine life and performance
To Service
could
Yearly or every 25 hours, whichever
occurs first,
remove the btower housing and clean lhe areas shown
in figure 16 to avoid overspeeding,
overheating
and
engine damage
Clean mere often if necessary
8
Never run your engine without
ly assembled,
as water
air cleaner complete-,
Clean Out
Air Cleaner:
Clean cartridge at three month intervals or every 25
hours, whichever occurs first See figure 15, Service
more often under dusty conditions
e Loosen screws and tilt cover as illustrated
e Carefully remove pre-cleaner
_
FIGURE 16_
and cartridge
Clean cartridge by tapping gently on a flat surface
If very dirty, replace cartridge and pro-cleaner or
clean as follows:
Wash in a low or nomsudsing detergent and warm
water solution CAUTION: Do not use petroleum
solvents such as kerosene to clean cartridge
SPARK PLUG
The spark plug should l_e cleaned and the gap reset
to 030" at least once a season or every 50 hours of
operation See figure 17 Spark plug replacement is "
recommended at the starl of eachseason. Refer to
engine parts fist for correct spark plug type,
Rinse thoroughly with flowing water from inside out
_.mtilwater is clear
NOTE: Do not sandblast sPark plug Spark plug should
be cieaned by scraping or wire brushing and washing
with a commercia! solvent
Allow cartridge to stand and ail dry thoroughly
before using DO NOT OIL CARTRIDGE OR PRECLEANER DO NOT USE PRESSURIZED AIR TO
CLEAN OR DRY CARTRIDGE,
o Install cartridge and pre-cleaner
and fasten screws securely
Chaff and Dirt
Then close cover
Spark
FIGURE
Screw
Plug
17.
MUFFLER
Do not operate the chipper-shredder without a muffler
or tamper with the exhaust system Damaged mufflers
or spark arresters could create a fire hazard, Inspect
periodically, and reptace if necessary If your engine
is equipped with a spark arrestor screen assembly,
remove every 50 t_ours for cleaning and inspection
Replace if damaged
i_.
FIGURE
CLEAN
Base
CLEANING
e The chipper-shredder may be cleaned by running
water from a hose through the hopper assembly and
chipper chute with the engine running Allow the
chipper-shredder to dry thoroughly
15.
ENGINE
Clean engine periodically
a ctoth or brush Cleaning
Remove dirt and debris with
with a forceful spray of water
e Wash the bag periodically with water Attow to dry
thoroughly in the shade Do not use heat
tt
STORAGE
Fuel Stabilizer No 33500 may be added to any gasoline
left in the tank to minimize gum deposits and acids If
the tank is almost empty, mix stabilizer with fresh
gasoline in a separate container and add some to the
tank Always follow instructions on stabilizer container, Then run engine at least 10 minutes after
stabilizer is added to allow mixture to reach carburetoro Store chipper-shredder
in safe place, See
warning in previous column.
NEVER
STORE
YOUR
CHIPPERSHREDDER INDOORS OR IN AN ENCLOSED_ POORLY VENTILATED AREA IF
GASOLINE REMAINS
IN THE TANK.
FUMES MAY REACH AN OPEN FLAME,
SPARK OR PILOT LIGHT FROM A
FURNACE, WATER HEATER, CLOTHES
DRYERs CIGARETTE, ETC.
You can help keep your engine in good operating condition during storage by:
To prevent engine damage if chipper-shredder is not
used for more than 30 days, follow the steps below
e Changing oil
NOTE: GASOLINE
MUST
BE REMOVED OR
TREATED TO PREVENT GUM DEPOSITS FROM
FORMING IN THE TANK, FILTER, HOSE AND CARBURETOR DURING STORAGE
ALSO DURING
STORAGE, ALCOHOL-BLENDED
GASOLINE THAT
USES ETHANOL OR METHANOL (SOMETIMES
CALLED GASOHOL) ATTRACTS WATER. IT ACTS
ON THE GASOLINE TO FORM ACIDS WHICH
DAMAGE THE ENGINE.
e Lubricating the pistonlcytinde_ area by first removing the spark plug and squirting clean engine oil into the spark plug hole Then cover the spark plug
hole with a rag to absorb oil spray Next, rotate the
engine by pulling the starter two or three times
Finally, reinstall spark plug and attach spark plug
wire
Protect the chipper-shredder
o Thoroughly
To remove gasoline, run engine until tank is empty and
during storage by:
cleaning the chipper-shredder.
e If storing in an unventilated or metal storage shed,
coat metal parts with a light oil or silicone to prevent
rust,
engine stops Then disconnect fuel line at carburetor
or fuel tank, Be careful not to damage fuel line, fittings
or fuel tank Drain any remaining fuel from the system
If you do not want to remove gasoline, Sears Craftsman
e Store in a clean, dry area
12
DOE & ADJUST[ ENT
Remove the chipper chute by removing three hex
nuts and washers
A 1/2" wrench is required
See
figure 18
WARNING:
ALWAYS STOP ENGINE AND
DISCONNECT
SPARK PLUG WIRE AND
MOVE 1T AWAY FROM SPARK PLUG BE,.
FORE
PERFORMING
ANY
ADJUSTMENTS OR REPAIRS,
NOTE: When reassembling,
on the bottom of the chipper
against the chute
the cupped washer goes
chute with the cupped side
e Rotate the impeller assembly by hand until you
locate one of the chipper blades in the chipper chute
opening. Remove the blade, using a 3/16" allen
wrench on the outside of the blade and ti2" wrench
REMOVINGTHE FLAIL SCREEN
If the discharge area becomes clogged, remove the ftaii
screen and clean area as follows
e Stop the engine, make certain the chipper-shredder
has come to a complete stop and disconnect spark
plug wire from the spark plug before unclogging the
chute
on the impeller assembly (inside lhe housing)
figure 19
See
e Remove the other blade in the same manner
\
e Loosen the two hand knobs on each side of the
chute deflector. Lift the chute deflector up, and tie
it out of the way
e Remove two hairpin clips from the clevis pins which
extend through the housing Remove the clevis pins
Lift the flail screen from inside the housing.. See
figure 18
e Clean the screen by scraping or washing with water
Reinstall the screen
NOTE: Be certain to reassemble the flail screen with
the curved side down as shown in figure t8
Chute
FIGURE
7./"
19.
Replace or sharpen blades If sharpening, make cer_
tain to remove an equal amount from each blade
Reassemble in reverse order
Make certain blades are reassembled with the sharp
edge facing the direction shown in figure 19 (sharp
edge is assembled toward the slotted opening in the
impeller assembly),
_'Hex
Flail
Screen
Washers4
SHREDDING
The shredding blade may be removed for sharpening
or replacement as follows.
Chute
o Lower the hopper assembly
See figure 20
Hand Knobs
FIGURE
BLADE
Remove lhe four hex lock nuts and lock washers
from the housing weld bolts using a t12" wrench
Separate the chipper-shredder into two halves
18.
SHARPENIN6 OR REPLACIN6 THE BLADES
CHIPPER BLADES
e Disconnect spark plug wire and move i1 away from
spark plug
e Remove the flail screen as instructed
section
Block up the housing
e Remove the back-up plate
NOTE: When reassembling, make certain the opening
on the back-up plate is toward the bottom of the unit
The back-up plate may be reversed to provide a new
cutting edge
in previous
13
FLAILS
The flails, located inside the housing, may be reversed
when they become dull It is suggested that this procedure be performed by your nearest Sears Service
Department
CARBURETORADJUSTMENT
Blade
R
WARNING: IF ANY ADJUSTMENTS ARE
MADE TO THE ENGINE WHILE THE
ENGINE
IS RUNNING
(EoG,. CARBURETOR),
KEEP CLEAR OF ALL
MOVING
PARTS.
BE CAREFUL
OF
HEATED SURFACES AND MUFFLER.
Minor carburetor adjustment may be required to compensate for differences in fuel, temperature, altitude or
load
FIGURE
20,.
NOTE: A DIRTY AIR CLEANER WILL CAUSE ENGINE
TO RUN ROUGH. BE CERTAIN AIR CLEANER IS
CLEAN AND ATTACHED TO THE CARBURETOR
BEFORE ADJUSTING
CARBURETOR.
DO NOT
MAKE UNNECESSARY ADJUSTMENTS
FACTORY
SETTINGS ARE SATISFACTORY
FOR MOST APPLICATIONS AND CONDITIONS.
e Hold the blade retainer on the impetier assembly
with an adjustable wrench to keep the blade from
turning as shown in figure 2Q
e Remove the blade by removing the center bolt, lock
washer and ftat washer
Never attempt to change maximum engine speed It
is pre-set at the factory and should be changed only
by a qualified service technician who has the necessary
equipment
NOTE: Use caution when removing the blade to avoid
contacting the weld bolts on the housing.
e When sharpening the blade, follow the original angle
of grind as a guide. It is extremely important that
each cutting edge receives an equal amount of
grinding to prevent an unbalanced blade. An unbalanced blade will cause excessive vibration when
rotating at high speeds and may cause damage to
the unit
The carburetor may need re-adjusting if engine lacks
power or does not idle properly, if adjustments are
needed, proceed as follows
e Close needle valve (see figure 22) clockwise
( ,'_ ) finger tight only Forcing may cause damage
Then open !1/z turns counterclockwise ( f_ )
e The blade can be tested for balance by balancing
it on a round shaft screwdriver or nail. Remove metal
from the heavy side until it is balanced evenly See
figure 2t
e Start engine and allow to warm for five minutes
e With throttle in FAST position, close needle valve
clockwise (,'_)
until engine starts to lose speed
(lean mixture) Then slowly open needle valve
counterclockwise ( f-', ) until engine JUST BEGINS
to run unevenly This mixture should be rich enough
for best performance under load.
® Place throttle control in IDLE position
If engine idles, no further adjustment is necessary.
If engine idles too fast, turn idle speed adjusting
screw counterclockwise ( t'm ) until slower speed is
obtained
FIGURE
•
tf engine dies, turn idle speed adjusting screw 1/4
turn clockwise (('_)
Place throttle control in FAST
position and restart engine
21.
When reassembling
the blade, tighten to between
550 and 650 inch pounds, or lacking torque wrench,
tighten securely
Move throttle cont(ot to IDLE position If engine does
not idle, repeat step c
14
e Testthe engine
ENGINE SPEED
by using the chipper-shredder
If
engine tends to stall or die out, it usually indicates
that the mixture
is slightly
lean and it may be
necessary
to open ( F'_ ) the needle valve slightly
to provide a richer mixture This richer mixture may
cause a slight unevenness
in idling
Idte Speed
Adjusting Screw
Your engine speed has been factory set Do not attempt
to increase engine speed Or it may result in personal
injury tf you believe the engine is running too fast or
too stow, take your chipper-shredder to the nearest
SEARS Service Center for repair and adjustment
Throttle
Stop
Throttle
Needle Valve
FIGURE
22,
,,,,,,,,i,,/,
lul
Jl ,
SERVICE RECOMMENDATIONS
SERVICE RECORD
SCHEDULE
SERVICEDATES
Fill in dates as you
complete regular service
First
Before
5
Each
Hours'
Use
t
Every
25
Hours
Betore
Begin..
ning Each Storage
Season
Every
50
Hours
.............
Check Fuel
if
Drain Fuel
If
!
Check Engine Oil Level
..........................
...........................
Change Engine Oil
.........
,.._
i
_-"
•
1
,,,
,i
if
:
,.
,,.-
Oil Pivot Points
v"
Service Air Cleaner
Clean Engine Cylinder Fins
!
._'
al
Replace or Clean Spark Plug
,,.
Spark Arrester Muffler
,..-
The Service Recommendations Chart is supplied to
assist the operator in proper maintenance of the
chipper-shredder This is only a check list; instructions
will be found in the Maintenance and Service Adjustment sections of this manual
15
,
i
i
_ .......
i
......
JJiJ iiiJ
i ,,
TROUBLE
PROBLEM
POSSIBLE
i
iJ
i ,,,.i.i
JJ ii
ii
L
SHOOTDNG
CORRECTIVE
CAUSE(S)
ACTION
Engine fails le start
1 Fuel tank empty, or state fue!
2 Spark plug wire disconnected
3 Faulty spark plug
1 Fill lank with clean, fresh fuel
2 Connect wire to spark plug
3 Clean, adjusl gap or replace
Loss of power;
operation erratic
1 Spark plug wire loose
2 Unit running on CHOKE
3 Blocked fuel fine or stale fuel
1 Connect and tighten spark plug wire
2 Move choke lever to OFF position
3 Clean fuet line; fill tank with clean
fresh gasoline
4 Disconnect fuet line at carburetor to drain fuel
tank Refill with fresh fuel
5 Adjust carburetor or contact your SEARS
Service Center
4 Wafer or dirt in fue! system
5
Carburetor oul of adjustment
6 Dirty air cleaner
Engine overheats
Too much vibration
Unit does not
discharge
1 Adjust carburetor or contact your SEARS
Service Center
2 Fifl crankcase with proper oil
1 Carburetor not adjusted
properly
2 Engine oil level tow
Stop engine immediately and disconnect
spark plug wire Tighten all bolts and nuts
Make all necessary repairs, If vibration conlinues,
have uni! serviced by a SEARS Service Center
Loose parts or damaged
auger.
I
Discharge chute clogged
2 Foreign object lodged in impeller,
Rate of discharge
slows considerably or
composition of
discharged material
changes
Shredding blade andlor chipper
blades dull,,
NOTE: For repairs beyond the minor adjustments
1 Stop engine immediately and disconnect
spark plug wire Clean flat! screen and inside
of btower housing See ServicelAdjustments
section of this manual
2 Stop engine immediately and disconnect
spark plug wire, Remove lodged object
Sharpen or replace shredding
blades
listed above, please contact your nearest
16
and chipper
SEARS Service Center
SEARS
CRAFTSMAN
5 H,P, CHIPPER-SI4REDDER
MODEL
NO. 247,7'97851
Repair Parts
L.
J_7
,"
40
63
\
46
35
45
17
.......................
SEARS,CRAFTSMAN5
Repair
KEY
H.P,
t
2
13431
710-0818
3
4
5
714-0114
736-0217
736-0247
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
:1
:2
'3
:4
:5
',6
[7
'.8
11459B
7t 1-0564
7t t-0833A
7t 1-0834
715-0249
736-0!92
78! -0484
781-0490
710-!054
712-041 t
736-0119
710-I058
736_0142
750-0793
711-0835
736-.0329
7t 2-0287
7t 4-3010
781_0457
7t 4-0149
781_0480
712-3010
736-0242
720-0170
747-0_'44A
732-0542
781-0489
781-0475
736-0170
712-30t0
781-0510
_O
H
_2
_4
_5
IE
MODEL
NO,
247,797851
.....
Parts
PART
NO.
NO.
CHIPPER-SHREDDER
DESCRIPTION
Blade
Hex Patch Bolt 3/8o24 x 2" Lg
(Gr 8)
Sq, Key 1/4 x 2.0" Lg
L-Wash, 318" I.D H D
Ft-Wash 406" ID x 1.25"
OD Hdn
Ftait
Flail Spacer
Clevis Pin 496" Dia,
Flail Spacer w/160" Die Hole
Spring Roll Pin 1,t2" Lg
Ft-Wash. 53t"iD
x.94
OD
Impeller Ass'y.
Chipper Blade
Flat Hd Scr. 5!t6-24 x .75" Lg
Hex Top L-Nut 5/16.24 (Gr 5)
L-Wash, 5/16" I D "
Hex Bolt 1/4-20 x 40" Lg *
FI-Wash_ .28t" I.D x .50" QD,
Chute Hinge Spacer 1.66" Lg
Clevis Pin .5" Die. x 4.62" Lg.
L-Wash, If4" I_D.*
Hex Nut !/4-20 Thd "
Cotter Pin
Shredder Screen
Internal Cotter Pin 318" Dia
Chute Deflector Ass'y
Hex Nut 5116-18 Thd (Gr. 5)
Bell-Wash. 345" ID x 88"
Hand Knob
Chipper Door Rod
Torsion Spring 1 14" Lg
Chipper Door
Chipper Chute Ass'y
Spec L-Wash, 5tt6" i D
Hex Nut 5t16-I8 Thd (Gr. 5)
Shredder Frame
*Common Hardware_May
I KEY i
PART
NO,
DESCRIPTION
37 710-0157
38 736-0119
39 710-3008
Hex Bolt 5/16-24 x 75" Lg
L-Wash. 5/!6" I.D "
Hex Bolt 5I!6-18 x 75" Lg
4O
4l
42
43
44
45
46
47
48
710-0380
781-0473
781-0474
735-0639
130212-3250-01
747-0531A
742-0546
712*0429
710-0601
49
5O
51
52
53
54
55
56
1t 480
736-0264
71O-O542
781-0487A
16522A
781 -O494
16524B
710-0286
57
58
59
60
61
62
63
64
65
66
67
68
712-0107
11461B
726-0214
736-0187
750-0786
738-0814
734-1600
732-0629
747-0747
78t -0492
781-0493
726-0106
764_0199A
723-0400
770-711 OF
Hex Bolt 5/16-!8 x 1 75" Lg '
Flail Housing Ass'y _LH
Flail Housing Ass'y--R.H
Spark Plug Boot
Engine--B&S
!30212-3250_01
Release Bar
Torsion Spring 106" Lg
Elastic Lock Nut 5!16-!8 Thd
Hex Wash Hd. Self-Tap Scr
5116-18 x 75" Lg
Stop Washer
FI-Wash, 5tt6" I D
Hex Bolt 5116-18 x 8 38" Lg
Back-Up Plate
Inlet Guide Ass'y.
Pivot Hopper Hood
Upper Guide Ass'y
Truss Mach Scr 114-20 x 5"
Lg.
Hex L-Nut 1!4-20 Thd
Upper Leaf Ramp Section
Push Cap 5t8" Die Rod
FFWash .64" 1D x t,24"
Spacer 64" ID x 38" Lg
Shredder Axle
Wheel Ass'y Comp
Torsion Spring
Hopper Door Rod
Hopper_Pivot
Doer
Hopper Lockout Brkt,
Cap Speed Nu!. V,_" Rod
Bag (Not Shown)
Safety Glasses (Not Shown)
Owner's Manual
(Gr. 5)
Be Purchased Locally
18
BRIGGS
Repair
AND
STRATTON
5 H.P,
ENGINE
MODEL
NO.
130212-3250-0t
Parts
337
33
30
36
35
741
\
'_SPEL--'I.ALTO('/,_SRE_JIRED
TO It%TALL
23O
_)15
2t9
46
220
19
SEE R.E:F_RLI',B-IT,{UCTION
MANUAL
.... BRIGGS:AND
Repair
STRATTON
5 H,P,
ENGINE
MODEL
NO, 1302t2-3250-01
Parts
24
6B
0
"/4
@
71
200
Q
373
305
O
37
*REQUIRES
SPECIAL
TOO_L_
TO INSTALL.
SEE REPAIR
INSTRUCTION
MANUAL.
2O
[:_
BR6GGS
AND
STRATTON
5 H,P_ ENGIh_E
_V_ODEL NO.
!30212-3250-01
Repair Parts
208
I017
190
191
527
725
S_
II
2'I
BRIGGS
AND
Repair
KEY
I
STRATTON
5 H.P. ENGINE
MODEL
NO,
130212-3250-01
Parts
PART
NO
395990
297565
299819
211542
*272157
294178
'27549
93394
66578
_270080
*270125
'270126
94221
93369
91249
492926
493916
297603
298504
66768
94607
297229
222698
298904
298905
298906
298907
298982
298983
298984
298985
26O26
298909
298908
299430
221890
221876
DESCRIPTION
K EY
hO
Cylinder Assembly
Bushing--Cylinder
Note: Requires special tools
for installation.
Seal--Oil
Head--Cylinder
Gasket--Cylinder
Head
Breather--Valve Chamber
Gasket--Valve Cover
Screw--Breather
Mtg, Sam
Grommet--Breather
Tube
Gasket--Crankcase-0I 5"
Thick (Standard)
Gasket--Crankcase-005"
Thick
Gasket--Crankcase-009"
Thick
Screw--Cylinder
Head
(2-3132" Long)
Screw--Cylinder
Head
(2-15/32" Long)
Plug--Pipe, tt4" Std Square
Head
Crankshaft
To Replace Crankshaft Gear
Pin, Order Part No. 230978
Cover Ass'y
Bushing--Crankcase
Cover
Note: Requires special tools
for installation
Seat_Oil
Plug_Oil Filler
Screw_Crankcase
Cover
Mounting Sere
Ftywheel_Magneto
Key_Flywheel
Piston Ass'y,_Standard
Piston Ass'y._O10"
OS
Piston Ass'y,_ 020" O S
Piston Ass'y._.030"
O,S
PISTON RING SETS,,
Note: For Chrome Piston Ring
Set--Standard
Size_Order
Part No 299742,,
Ring Set--Standard Piston
Ring Set_0t0"
O.S Piston
Ring Set_020"
O.S Piston
Ring Set_030"
OS Piston
Lock--Piston Pin
Pin Ass'y _Piston_Standard
Pin Ass'y--Piston_005"
OS
Rod Ass'y _Connecting
Note: For Connecting Rod
with 020" undersize Crankpin
Bore--Order No, 390459
Dipper_Connecting
Rod
Lock--Conn. Rod Screw
22
PART
NO
32
33
34
35
36
37
40
45
46
52
55
56
57
58
92296
211119
261044
260552
26478
222443
93312
260642
212733
*271936
299431
295871
490179
66884
59
60
65
490653
490652
94128
66
67
68
70
71
73
74
75
90
95
399671
394897
63770
298799
394506
221923
93490
224061
492611
93499
96
97
108
118
124
127
t27_
149
152
153
t54
223793
490048
491177
231533
93357
220352
223789
26336
260575
490589
93527
163
180
181
190
271935
492927
490075
94094
t9"1
20O
20t
202
203
204
*271928
223886
262280
262270
28072O
222962
205
208
2O9
231520
262279
262283
DESCRIPTION
Screw_Connecting
Rod
Vatve_Exhaust
Vatve_lntake
Spring--Intake
Valve
Spdng_Exhausl
Valve
Guard---FlywheeI
Retainer_Valve
Spring
Tappet_Valve
Gear_Cam
Gasket_Carburetor
Mounting
Housing_Rewind
Starter
Pulley_Rewind
Starter
Spring-Rewind Starter
Rope_Rewind
Starter_63"
Long
Insert_Starter
Handle
Handle_Rewind
Starte_
Screw_Stamped
Steel
Housing Mtg Sam
Clutch Ass'y,_Rewind
Starter
Housing_Starter
Clutch
Ball--Clutch
Ratchet_Rewind
Starter
Washer_Ctutch
Retainer
Screen_Starter
Pulley
Screw_Sem
Washer_Spring
Carburetor Assembly
Screw_Throttle
Valve to Shaft
Sere
Throttle,--Carburetor
Shaft and Lever_Throttle
Valve Group_Choke
Valve_Needle
Screw_Hex
Head
Plug_Welch
Plug_Welch
(Mixing Chamber)
Spring--Needle
Valve
Spring--Throttle
Adjustment
Screw Ass'y
Screw_Machine,
Rd Hd-5-40 x 5f8"
Gasket_Air
Cleaner Mounting
Tank Assembly_Fuef
Cap--Fuel Tank
Screw_Fuet
Tank Mounting
Sam
Gasket_Fuef
Tank Mounting
Guide_Air
Link_Governor
Link_Throttle
Crank_BelI
Bushing_Governor
Lever
{Fiat)
Screw_Shoulder
Rod_Control
Spring--Governor
BRIGGS
AND
Repair
KEY
NO,
5 H_P, ENGINE
MODEL
NO. 130212-3250-01
Parts
PART
NO
_16
2!9
?2O
_22
_23
224
262359
391737
221551
490649
223455
93491
2.27
23O
256
284
298
299
3O4
3O5
490374
222450
223813
94419
261409
393368
490169
94608
306
307
221511
93758
308
333
335
,_37
221512
397358
93414
492167
346
356
358
363
93705
398808
397145
19069
373
383
392
394
414
432
433
434
435
441
467
523
524
525
526
92987
89838
262328
270026
220982
221377
93265
210959
93141
224240
280715
492249
271485
280508
94409
527
528
529
STRATTON
223786
231550
67838
PART
NO,
DESCRIPTION
Link--Choke
Gear--Governor
Washer--Thrust
Bracket--Control
Lever--Governor
Control
Rivet--Governor
Conlrol Lever
Mounting
.ever Ass'y--Governor
Washer--Governor
Lever
Bell Crank
Screw--Seff-Tapping
Lock Nut--Muffler
Muffler_Exhaust
Housing--Blower
Screw--Blower
Housing
Mounting
Shietd_Cylinder
Screw--Cylinder
Shield
Mounting Sere
Cover--Cylinder
Head
Armature Assembly
Screw_Armature
Mtg, Sere
Plug--Spark 7/8" High48 M,M,
Screw--Sere
Wire--Ground
Gasket Set
Flywheel Puller (Optional
Accessory)
Nut_Hex
Wrench_Spark
Plug
Spring--Fuel Pump Diaphragm
Diaphragm
Washer
Cap--Spring
Pin--Diaphragm
Cover
Cover_Diaphragm
Screw--,Diaphragm
Cover
Bracket--Oil Fill
Knob--Contro!
Cap--Oil Fill
Gasket--Oil Fil! Cap
Nipple--Oil
Flll
Screw_Tank
Bracket
Mounting Sere
Clamp--Breather
Tube
Tube--Breather
Grommet--Breather
Tube
"Included in Gasket Set_
Part No 397145
DESCRIPTION
535
542
552
491435
93572
231079
Eiemenl--Air Cleaner
Screw
Bushing_Governor
Crank
562
592
608
611
614
615
616
821
634
635
643
643#
655
92613
231082
390463
391813
93306
93307
231077
396847
271853
66538
280737
280726
222598
395700
Bolt_Governor
Lever
Nut_Hex _10_24
Starter Ass'y --Rewind
Fuel Pipe and Clip Assembly
Cotter--Hairpin
Retainer--EoRing
Crank_Governor
(V4" Dia,)
Switch--Stop
Washer_Throttle
Shaft (Foam)
Elbow_Spark
Plug
Retainer_Foam
Element
Retainer--Air
Filter
Anchor Spring
Deflector_Exhaust
(Direct Outlet)
Washer Choke Shaft (Foam)
Washer Choke Shaft (Brass)
Shield_He_t
Ge'ar_Timirig
Link_Betl Crank
Seat_Tube
Oil Fill Ass'y
Cable Terminal--ignition
Seat--Intake Valve (Standard)
Seat_Exhaust
Valve
(Standard)
Note: For Options see Repair
Manual
Guide_Exhaust
Valve
Note: 63709 Go!de--Intake
Valve See Repair Instruction
Manual
Gear Rack--Governor
Base--Air Cleaner
FiRer--Air
Cover_Air Cleaner
Screw_Cover
Mtg
Screw_Air
Cleaner
Seal--Throttle
Shatt
Bracket_Link
Link--Retainer
Spacer
Decal (Label) Kit
(1_
270382
221839
223867
261696
262276
270920
493367
221798
2'11787
2I'1172
262001
280321
492797
491588
223765
490073
940'18
398970
223887
490507
490817
491100
SPARK ARRESTING MUFFLER ASSEMBLY
(Optional Equipment)
Consists of the following:
392154 Screen (1 required)
223372 Deflector (1 required)
93705
Screw (4 required)
23
't
392390
[D)
0WNE 'S
MANUAL
MODELNO,
247.797851
5 HORSEPOWER
3 CUTTBNG STAGE
MULCHING AND BAGGaNG
CHRPPER-SHREDDER
Each chipper-shredder
has its own model
engine has its own model number_
number.
The model number for your chipper-shredder
on a label attached to the frame,
The model number for the engine
blower housing of the engine,
Each
will be found
will be found on the
All parts listed herein may be ordered through Sears,
Roebuck and Co. Service Centers and most Retail Stores,
WHEN
ORDERING
THE FOLLOWING
HOWTOORDER
REPAIRPARTS
* PRODUCT
- "5
* MODEL
NUMBER
" ENGINE
MODEL
REPAIR
PARTS,
INFORMATION:
ALWAYS
GIVE
HoP. Chipper-Shredder"
- 247,797851
NO. - 130212-3250-01
* PART
NUMBER
* PART
DESCRIPTION
Your Sears merchandise has added value when you consider that Sears has service units nationwide staffed with
Sears trained technicians
.. professional
technicians
specifically trained on Sears products, having the parts,
tools and the equipment to insure that we meet our pledge
to you .... we service what we sell."
SEARS,
770-7110F
10/90
ROEBUCK
AND CO,, Chicago,
IL
60684
U.S,A ....
Printed
in U,S,A