Motorola LS1203 Instruction manual

SYMBOL LS1203
Quick Start Guide
STEP 1 - ATTACH CABLE TO SCANNER
http://www.motorola.com/ls1203
Attach Cable
Remove Cable (to change interface)
Or
See Product Reference Guide for detailed information
STEP 2 -CONNECT CABLE TO A HOST
NOTE: Cables may vary depending on configuration.
USB
Keyboard Wedge
RS-232
Note: Power Supply Optional
STEP 3 - SET UP INTERFACE (Scan Host Bar Codes)
Important: Out of box, Keyboard Wedge and USB interfaces require no bar code scan setup. Bar codes are provided for complex programming or interface changes.
USB
Keyboard Wedge
Scan ONE of the bar codes below
RS-232
Scan ONE of the bar codes below
Scan ONE of the bar codes below
IBM HAND-HELD USB
IBM AT Notebook
OPOS/JPOS
HID KEYBOARD EMULATION
IBM PC/AT and IBM PC COMPATIBLE
STANDARD RS-232
ADD AN ENTER KEY (CARRIAGE RETURN/LINE FEED)
Adding an Enter Key after scanned data; Scan all THREE bar codes in numerical order.
1
2
3
SCAN OPTIONS
<DATA><SUFFIX>
ENTER
ADD A TAB KEY
To add a Tab key after scanned data, scan all THREE Enter key bar codes above in numerical order then scan all FIVE bar codes below in numerical order.
1
2
3
4
5
SCAN SUFFIX
7
0
0
9
HANDS FREE STAND
OPTIMUM SCANNING
SET DEFAULTS
123SCAN2
Toggle Triggered Mode and Autoscan Mode
Return to Factory Defaults
123Scan2 is an easy-to-use, PC-based
software tool that enables rapid and easy
customized setup via a bar code or USB
cable. For more information, visit:
http://www.motorola.com/123Scan2.
012345
SET DEFAULTS
012345
SCANNER INDICATIONS
TROUBLESHOOTING
LED Indications
Off
Troubleshooting
Green
Scanner is on and ready to scan,
or no power to scanner
Bar code is successfully
decoded
Red
Transmission error
Standard Use
Short medium beep
Power up
Bar code decoded
Parameter Menu Scanning
High/low beep
High/low/high/low beep
Successful parameter setting
No power to scanner
Check system power;
ensure power supply,
if required, is connected
Beeper Indications
Low/medium/high beep
Correct programming
sequence performed
Scanned data incorrectly displayed on host
Scanner not working
4 long low beeps
Transmission error detected,
data is ignored
Incorrect interface cable used
Ensure that correct interface
cable is used
Ensure all cable connections
are secure
Scanner not programmed for correct host interface
Scan appropriate host parameter bar codes
Scanner decoding bar code, but data not transmitting to host
Scanner not decoding bar code
Scanner not programmed for correct host interface
Scanner not programmed
for bar code type
Scan appropriate host parameter bar codes
Low/High beep
Interface/power cables are loose
Interface cable is loose
Ensure all cable connections are secure
Incorrect programming sequence
or ’Cancel’ bar code scanned
Bar code unreadable
Ensure scanner is
programmed to read
type of bar code
being scanned
Ensure bar code not
defaced; try scanning
test bar code of same
bar code type
Distance between scanner
and bar code incorrect
Move scanner closer to
or further from bar code
RECOMMENDED USAGE GUIDE - OPTIMUM BODY POSTURE
Avoid Extreme Wrist Angles
Avoid Bending
Avoid Reaching
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of
ergonomic injury follow the recommendations below. Consult with
your local Health & Safety Manager to ensure that you are adhering
to your company's safety programs to prevent employee injury.
AVOID EXTREME
WRIST ANGLES
AVOID BENDING
AVOID REACHING
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
REGULATORY INFORMATION
© MOTOROLA, INC. 2010 All rights reserved.
Motorola reserves the right to make changes to any product to improve reliability, function, or design.
Motorola does not assume any product liability arising out of, or in connection with, the application or
use of any product, circuit, or application described herein. No license is granted, either expressly or by
implication, estoppel, or otherwise under any patent right or patent, covering or relating to any
combination, system, apparatus, machine, material, method, or process in which Motorola products
might be used. An implied license exists only for equipment, circuits, and subsystems contained in
Motorola products.
Laser Labels
In accordance with Clause 5, IEC 825 and EN60825, the following information is provided to the user:
Warranty
Regulatory Information
Symbol Technologies, Inc., the Enterprise Mobility business of Motorola, Inc. ("Motorola").
All Symbol devices are designed to be compliant with rules and regulations in locations they are sold and
w be labeled as required.
Any changes or modifications to Symbol Technologies equipment, not expressly approved by Symbol
Technologies, could void the user's authority to operate the equipment.
Antenna’s, use only the supplied or an approved replacement antenna. Unauthorized antennas,
modifications, or attachments could cause damage and may violate regulations.
Laser Devices
For the complete Motorola hardware product warranty statement, go to:
http://www.motorola.com/enterprisemobility/warranty.
Symbol products using lasers complies with 21CFR1040.10 and 1040.11 except for
deviations pursuant to laser notice No. 50, dated June 24, 2007 and IEC 60825-1 (Ed. 2.0),
EN60825-1:2007. The laser classification is marked on one of the labels on the product. Class 1
Laser devices are not considered to be hazardous when used for their intended purpose.
The following statement is required to comply with US and international regulations:
Caution: Use of controls, adjustments or performance of procedures other than those specified herein
may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright light source, such as the
sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not
known to be harmful.
Service Information
If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there
is a problem with the equipment, they will contact the Motorola Enterprise Mobility Support at:
http://www.motorola.com/enterprisemobility/contactsupport.
For the latest version of this guide go to: http://www.motorola.com/enterprisemobility/manuals.
Waste Electrical and Electronic Equipment (WEEE)
Radio Frequency Interference Requirements
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in residential installation. This equipment
FOR HOME OR OFFICE USE
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. However there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Tested to comply
with FCC Standards
POST IN WORK AREA
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements – Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Marking and European Economic Area (EEA)
Statement of Compliance
Symbol Technologies, Inc., hereby declares that this device is in compliance with all the
applicable Directives, 89/336/EEC, 73/23/EEC. A Declaration of Conformity may be obtained from
http://www.motorola.com/enterprisemobility/doc
Motorola, Inc. One Motorola Plaza , Holtsville, New York 11742-1300, USA
http://www.motorola.com/enterprisemobility
MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U.S.
Patent and Trademark Office. All other product or service names are the property of their
respective owners. © Motorola, Inc. 2010
Power Supply
Note: Use only a Symbol-approved power supply (p/n 50-14000-253R, 50-14000-256R, 50-14000-257R,
50-14000-258R or 50-14000-259R) output rated 5 VDVC and minimum 650mA. The power supply is certified
to EN60950 with SELV will invalidate any approval given to
this device and may be dangerous.
Hinweis: Benutzen Sie nur eine von Symbol Technologies genehmigte Stromversorgung mit einer
Ausgangsleistung von 5 VDC (Gleichstrom) und mindestens 650mA. Die Stromversorgung ist nach EN60950
für die Verwendung in SELV-Stromkreisen zertifiziert. Bei Verwendung eines anderen Netzteils werden alle
für das Gerät gewährten Genehmigungen außer Kraft gesetzt, und der Betrieb kann gefährlich sein.
72-115933-01 Revision B March 2010
SYMBOL LS1203
http://www.motorola.com/ls1203