Samsung OFFICESERV ITP-5014D Installation guide

GANA-000024
Ed. 01
OfficeServ 500
Programming Guide
06. 2004.
COPYRIGHT
This guide is proprietary to SAMSUNG Electronics Co., Ltd. and is protected by copyright.
No information contained herein may be copied, translated, transcribed or duplicated for any commercial
purposes or disclosed to third parties in any form without the prior written consent of SAMSUNG Electronics
Co., Ltd.
TRADEMARKS
TM
OfficeServ
is the trademark of SAMSUNG Electronics Co., Ltd.
Product names mentioned in this document may be trademarks and/or registered trademarks of their
respective companies.
Please read this guide before using the OfficeServ 500, and follow the instructions to use the OfficeServ 500
system safely and correctly.
This guide may be changed for the system improvement, standardization and other technical reasons without prior
notice.
For further information on the updated guide or have a question the content of guide, contact Document Center at the
address below.
Address : Document Center 2nd Floor IT Center. Dong-Suwon P.O. Box 105, 416, Maetan-3dong Yeongtong-gu,
Suwon-si, Gyeonggi-do, Korea 442-600
e-mail : manual@samsung.com
http://www.samsungdocs.com
©2004 SAMSUNG Electronics Co., Ltd.
All rights reserved.
OfficeServ 500 Programming Guide
INTRODUCTION
Purpose
This guide describes a programming method for the OfficeServ 500 system users.
OfficeServ 500 allows you to utilize a digital phone to simply change the system setup.
Likewise, using a phone to change the system setup is called MMC(Man Machine
Communication) program. This guide describes how to program a digital phone.
Document Content and Organization
This guide is composed of two Chapters and one Annex. Each chapter is introduced as
follows:
CHAPTER 1. Overview of MMC Programming
This chapter describes things to know before starting MMC programming and about the
buttons of digital phone and cautions.
CHAPTER 2. MMC Programming
This chapter describes how to use each MMC program as it was listed.
ANNEX A. ABBREVIATION
Acronyms frequently used in this document are described.
© SAMSUNG Electronics Co., Ltd.
I
INTRODUCTION
Conventions
The following special paragraphs are used in this document to point out information that
must be read. This information may be set-off from the surrounding text, but is always
preceded by a bold title in capital letters.
WARNING
Provides information or instructions that the reader should follow in order to avoid
personal injury or fatality.
CAUTION
Provides information or instructions that the reader should follow in order to avoid
a service failure or damage to the system.
CHECKPOINT
Provides the operator with checkpoints for stable system operation.
NOTE
Indicates additional information as a reference.
OPERATION PROCEDURES
Indicates the operational procedures that should be executed in sequence.
II
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Reference
OfficeServ 500 Installation Guide
Introduces the installation related information for OfficeServ 500 system.
OfficeServ 500 Service Manual
Introduces circuit configuration of each section in OfficeServ 500 system, main functions,
parts list, troubleshooting, and disassembly diagram of main device.
DS-5012L Digital Phone User’s Manual
This is a user’s manual for the Large LCD Digital Phone(DS-5012L) that can be used by
connecting to the OfficeServ 500 system.
ITP-5012L IP Phone User’s Manual
This is a user’s manual for the Large LCD IP Phone that can be used by connecting to the
OfficeServ 500 system.
DS-5038D/5021D/5014D Digital Phone User Guide
This is a user’s manual for the 2 Line LCD Digital Phone(DS-5038D, DS-5012D, DS5014D) that can be used by connecting to the OfficeServ 500 system.
ITP-5021D/5014D IP Phone User Guide
This is a user’s manual for the 2 Line LCD IP Phone(ITP-5021D, ITP-5014D) that can be
used by connecting to the OfficeServ 500 system.
OfficeServ 500 Wireless LAN Service Manual
Introduces information needed to install the wireless device of the OfficeServ 500 system
or for its maintenance.
WIP-5000M Phone User Guide
This is a user’s manual for WIP-5000M that is designed to use wireless LAN provided
from the OfficeServ 500 system.
Revision History
EDITION
DATE OF ISSUE
00
07. 2003.
01
06. 2004.
REMARKS
First Edition
- Addition of DS/ITP-5000D Series Phones
- Addition and modification of WLAN related MMC
© SAMSUNG Electronics Co., Ltd.
III
INTRODUCTION
This page is intentionally left blank.
IV
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide
SAFETY CONCERNS
For product safety and correct operation, the following information must be given to the
operator/user and shall be read before the installation and operation.
Symbols
Caution
Indication of a general caution
Restriction
Indication for prohibiting an action for a product
Instruction
Indication for commanding a specifically required action
© SAMSUNG Electronics Co., Ltd.
V
SAFETY CONCERNS
Warning
WARNING
When using this feature
Before using this feature make sure that you are not violating any state or federal
laws. Some states require that the recorded party be notified. SAMSUNG is not
responsible for any illegal use of this feature.
Caution
CAUTION
CALL COST
Changing this value when there is a call in progress may result in an inaccurate
call cost. This MPD facility requires the Meter Pulse Detection version of the trunk
card.
The DECT System Code/Register handsets Change
Only the system administrator and/or installer should be allowed access to
change the DECT System Code and Register handsets.
When changing the MMC [805], [809], [812] and [816]
MMC [805], [809], [812] and [816] should not be changed from the default levels
without the assistance of the local SAMSUNG distributor.
Compliance with the National Version Standard
For the national version, OfficeServ 500 is designed to comply with the standard
of the corresponding country. Therefore, in case the ‘Program 812 Program the
national standard change’ needs to be used, please call the service company
assigned by Samsung to get an expert’s advice.
VI
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide
TABLE OF CONTENTS
INTRODUCTION
I
Purpose ...........................................................................................................................................I
Document Content and Organization...............................................................................................I
Conventions ....................................................................................................................................II
Reference ......................................................................................................................................III
Revision History .............................................................................................................................III
SAFETY CONCERNS
V
Symbols ......................................................................................................................................... V
Warning......................................................................................................................................... VI
Caution ......................................................................................................................................... VI
CHAPTER 1. Overview of MMC Programming
1-1
1.1
Introduction to Programming................................................................................................... 1-1
1.2
Phone Buttons........................................................................................................................... 1-2
1.2.1
DS-4000 Series phones ....................................................................................................... 1-2
1.2.2
DS/ITP-5000D Series Phones .............................................................................................. 1-3
1.3
Cautions in Programming ........................................................................................................ 1-5
1.4
Program List by User’s Level................................................................................................... 1-6
1.4.1 Station Level Programming .............................................................................................. 1-6
1.4.2 Operator Level Programming ........................................................................................... 1-7
1.4.3 Technician Level Programming ...................................................................................... 1-13
1.5
Program List by Name ............................................................................................................ 1-15
1.6
Program List by Function....................................................................................................... 1-22
1.6.1 Phone Function .............................................................................................................. 1-22
1.6.2 Networking Function ...................................................................................................... 1-23
1.6.3 VoIP Function................................................................................................................. 1-23
1.6.4 WLAN Function .............................................................................................................. 1-24
1.6.5 LCR Function ................................................................................................................. 1-24
1.6.6 Auto Attendant/Voice Mail Function................................................................................ 1-24
© SAMSUNG Electronics Co., Ltd.
VII
TABLE OF CONTENTS
1.6.7 Diagnosis Function .........................................................................................................1-25
1.6.8 Hotel Function.................................................................................................................1-25
CHAPTER 2. MMC Programming
2-1
2.1
Overview of Programming Procedure......................................................................................2-1
2.2
Programming Procedure...........................................................................................................2-2
[100] STATION LOCK..................................................................................................................2-2
[101] CHANGE USER PASSCODE.............................................................................................2-4
[102] CALL FORWARD ...............................................................................................................2-5
[103] SET ANSWER MODE ........................................................................................................2-7
[104] STATION NAME .................................................................................................................2-9
[105] STATION SPEED DIAL .................................................................................................... 2-11
[106] STATION SPEED DIAL NAME .........................................................................................2-13
[107] KEY EXTENDER ..............................................................................................................2-14
[108] STATION STATUS ............................................................................................................2-17
[109] DATE DISPLAY ................................................................................................................2-19
[110] STATION ON/OFF ............................................................................................................2-21
[111] PHONE RING TONE.........................................................................................................2-23
[112] ALARM REMINDER CLOCK ............................................................................................2-24
[113] VIEW MEMO NUMBER ....................................................................................................2-26
[114] PHONE VOLUME .............................................................................................................2-27
[115] SET PROGRAMMED MESSAGE .....................................................................................2-29
[116] ALARM AND MESSAGE...................................................................................................2-30
[117] EDIT TEXT MESSAGE .....................................................................................................2-32
[118] CONFERENCE GROUP...................................................................................................2-33
[119] CALLER ID DISPLAY .......................................................................................................2-35
[120] LARGE LCD OPTION.......................................................................................................2-37
[121] PHONE LANGUAGE ........................................................................................................2-39
[122] NEWS DISPLAY SPEED ..................................................................................................2-41
[125] EXECUTIVE STATE .........................................................................................................2-42
[200] OPEN CUSTOMER PROGRAMMING .............................................................................2-44
[201] CHANGE CUSTOMER PASSCODE ................................................................................2-46
[202] CHANGE FEATURE PASSCODE ....................................................................................2-47
[203] ASSIGN UA DEVICE ........................................................................................................2-49
[204] COMMON BELL CONTROL.............................................................................................2-50
[205] ASSIGN LOUD BELL .......................................................................................................2-51
[206] BARGE-IN TYPE ..............................................................................................................2-52
[207] ASSIGN VM/AA PORT .....................................................................................................2-53
VIII
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[208] ASSIGN RING TYPE ....................................................................................................... 2-54
[209] ASSIGN ADD-ON MODULE ............................................................................................ 2-55
[210] CUSTOMER ON/OFF PER TENANT .............................................................................. 2-56
[211] DOOR RING ASSIGNMENT ............................................................................................ 2-61
[214] DISA ALARM RINGING STATION ................................................................................... 2-62
[215] VOICE DIALLER OPTIONS............................................................................................. 2-63
[216] VOICE DIALLER ASSIGNMENTS ................................................................................... 2-65
[217] TRAFFIC REPORT OPTION ........................................................................................... 2-66
[220] ISDN SERVICE TYPE ..................................................................................................... 2-68
[221] EXTENSION TYPE .......................................................................................................... 2-69
[222] FAX PAIR ......................................................................................................................... 2-71
[224] WAKE-UP ANNOUNCEMENT ......................................................................................... 2-72
[300] CUSTOMER ON/OFF PER STATION.............................................................................. 2-74
[301] ASSIGN STATION COS ................................................................................................... 2-76
[302] PICKUP GROUPS ........................................................................................................... 2-78
[303] ASSIGN BOSS/SECRETARY .......................................................................................... 2-79
[304] ASSIGN EXTENSION/TRUNK USE ................................................................................ 2-80
[305] ASSIGN FORCED CODE ................................................................................................ 2-82
[306] HOT LINE/OFF HOOK SELECTION................................................................................ 2-83
[308] ASSIGN BACKGROUND MUSIC SOURCE .................................................................... 2-84
[309] ASSIGN STATION MOH SOURCE .................................................................................. 2-86
[310] LCR CLASS OF SERVICE .............................................................................................. 2-88
[312] ALLOW CALLER ID ......................................................................................................... 2-89
[314] CONFIRM OUTGOING CALL.......................................................................................... 2-90
[315] CUSTOMER SET RELOCATION..................................................................................... 2-91
[316] COPY STN/TRK USE ...................................................................................................... 2-94
[317] ASSIGN STATION/STATION USE ................................................................................... 2-95
[318] DISTINCTIVE RINGING .................................................................................................. 2-96
[319] BRANCH GROUP............................................................................................................ 2-98
[320] PRESET FWD NO ANSWER........................................................................................... 2-99
[323] CALLING PARTY NUMBER........................................................................................... 2-101
[400] CUSTOMER ON/OFF PER TRUNK .............................................................................. 2-103
[401] TRUNK LINE/PBX LINE................................................................................................. 2-105
[402] TRUNK DIAL TYPE........................................................................................................ 2-106
[403] TRUNK TOLL CLASS .................................................................................................... 2-107
[404] TRUNK NAME ............................................................................................................... 2-109
[405] TRUNK CO TEL NUMBER .............................................................................................2-110
[406] TRUNK RING ASSIGNMENT .........................................................................................2-112
[407] FORCED TRUNK RELEASE ..........................................................................................2-113
© SAMSUNG Electronics Co., Ltd.
IX
TABLE OF CONTENTS
[408] ASSIGN TRUNK MOH SOURCE ................................................................................... 2-114
[409] TRUNK STATUS READ.................................................................................................. 2-116
[410] ASSIGN DISA TRUNK .................................................................................................... 2-118
[411] ASSIGN E1 SIGNAL TYPE............................................................................................. 2-119
[412] ASSIGN TRUNK SIGNAL ...............................................................................................2-122
[413] VMS CALL TYPE............................................................................................................2-123
[414] PRS SIGNAL ..................................................................................................................2-124
[415] REPORT TRUNK ABANDON DATA ...............................................................................2-126
[416] ASSIGN E & M/DID RINGDOWN ...................................................................................2-127
[417] E1/PRI CRC4 OPTION...................................................................................................2-129
[418] BRI AND PRI CARD RESTART......................................................................................2-130
[419] BRI OPTIONS ................................................................................................................2-131
[420] PRI OPTIONS ................................................................................................................2-135
[421] MSN DIGIT .....................................................................................................................2-137
[422] TRUNK COS ..................................................................................................................2-139
[423] S/T MODE ......................................................................................................................2-141
[424] BRI S0 MAPPING...........................................................................................................2-142
[425] ASSIGN CALLER ID TRUNKS .......................................................................................2-143
[426] TRUNK GAIN CONTROL ...............................................................................................2-145
[428] ASSIGN TRUNK/TRUNK USE .......................................................................................2-147
[433] COST RATE ...................................................................................................................2-148
[434] CONNECTION STATUS .................................................................................................2-149
[436] TRUNK TMC GAIN .........................................................................................................2-152
[500] SYSTEM-WIDE COUNTERS .........................................................................................2-153
[501] SYSTEM TIMERS ..........................................................................................................2-155
[502] STATION-WIDE TIMERS................................................................................................2-161
[503] TRUNK-WIDE TIMER.....................................................................................................2-163
[504] PULSE MAKE/BREAK RATIO ........................................................................................2-165
[505] ASSIGN DATE AND TIME ..............................................................................................2-166
[506] TONE CADENCE ...........................................................................................................2-167
[507] ASSIGN RING PLAN TIME ............................................................................................2-170
[508] CALL COST....................................................................................................................2-172
[510] SLI RING CADENCE......................................................................................................2-173
[511] MSG WAITING LAMP CADENCE ..................................................................................2-175
[512] HOLIDAY ASSIGNMENT................................................................................................2-176
[513] HOTEL TIMER................................................................................................................2-177
[514] TONE SOURCE .............................................................................................................2-178
[515] ASSIGN DAYLIGHT SAVING DATE ...............................................................................2-179
[600] ASSIGN OPERATOR GROUP .......................................................................................2-180
X
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[601] ASSIGN STATION GROUP ........................................................................................... 2-181
[602] STATION GROUP NAME............................................................................................... 2-186
[603] ASSIGN TRUNK GROUP .............................................................................................. 2-187
[604] ASSIGN STATION TO PAGE ZONE .............................................................................. 2-189
[605] ASSIGN EXTERNAL PAGE ZONE ................................................................................ 2-190
[606] ASSIGN SPEED BLOCK ............................................................................................... 2-191
[607] UCD OPTIONS .............................................................................................................. 2-193
[608] ASSIGN REVIEW BLOCK ............................................................................................. 2-198
[609] CALL LOG BLOCK ........................................................................................................ 2-199
[611] ALLOW TEXT MESSAGING .......................................................................................... 2-200
[612] ALLOW GROUP CONFERENCE .................................................................................. 2-201
[614] STATION/TRUNK USE GROUP .................................................................................... 2-202
[615] MGI GROUP .................................................................................................................. 2-203
[616] MGI USER ..................................................................................................................... 2-205
[700] COPY COS CONTENTS ............................................................................................... 2-206
[701] ASSIGN COS CONTENTS ............................................................................................ 2-207
[702] TOLL DENY TABLE ........................................................................................................2-211
[703] TOLL ALLOWANCE TABLE ........................................................................................... 2-213
[704] ASSIGN WILD CHARACTER ........................................................................................ 2-215
[705] ASSIGN SYSTEM SPEED DIAL .................................................................................... 2-216
[706] SYSTEM SPEED DIAL BY NAME ................................................................................. 2-218
[707] AUTHORIZATION CODE............................................................................................... 2-220
[708] ACCOUNT CODE .......................................................................................................... 2-221
[709] TOLL PASS CODE/SPECIAL CODE TABLE ................................................................. 2-222
[710] LCR DIGIT TABLE ......................................................................................................... 2-224
[711] LCR TIME TABLE........................................................................................................... 2-225
[712] LCR ROUTE TABLE ...................................................................................................... 2-226
[713] LCR MODIFY DIGIT TABLE .......................................................................................... 2-228
[714] DID NUMBER AND NAME TRANSLATION ................................................................... 2-230
[715] PROGRAMMED STATION MESSAGE .......................................................................... 2-233
[716] UK LCR OPTIONS......................................................................................................... 2-235
[717] UCD AGENT ID ............................................................................................................. 2-237
[718] MY AREA CODE ............................................................................................................ 2-238
[719] IDLE DISPLAY ............................................................................................................... 2-239
[720] COPY KEY PROGRAMMING ........................................................................................ 2-240
[721] SAVE STATION KEY PROGRAMMING......................................................................... 2-241
[722] STATION KEY PROGRAMMING ................................................................................... 2-242
[723] SYSTEM KEY PROGRAMMING ................................................................................... 2-247
[724] DIAL NUMBERING PLAN .............................................................................................. 2-249
© SAMSUNG Electronics Co., Ltd.
XI
TABLE OF CONTENTS
[725] SMDR OPTIONS ............................................................................................................2-255
[726] VM/AA OPTIONS ...........................................................................................................2-258
[727] SYSTEM VERSION DISPLAY ........................................................................................2-264
[728] CID TRANSLATION TABLE............................................................................................2-265
[730] AA RECORD GAIN .........................................................................................................2-266
[731] AA RAM CLEAR .............................................................................................................2-267
[732] AA TRANSLATION TABLE .............................................................................................2-268
[733] AA PLAN TABLE.............................................................................................................2-272
[734] AUTO ATTENDANT MESSAGE MATCH........................................................................2-276
[735] AA USE TABLE...............................................................................................................2-277
[736] ASSIGN AA MOH ...........................................................................................................2-279
[737] DECT SYSTEM CODE ...................................................................................................2-280
[738] DECT CLEAR REGISTRATION .....................................................................................2-282
[740] STATION PAIR ...............................................................................................................2-284
[741] DBS RESTART...............................................................................................................2-285
[742] BSI STATUS ...................................................................................................................2-287
[743] DBS STATUS..................................................................................................................2-288
[744] DECT REGISTRATION ON/OFF ....................................................................................2-289
[745] BSI RF CARRIER ...........................................................................................................2-290
[746] COSTING DIAL PLAN ....................................................................................................2-291
[747] RATE CALCULATION TABLE ........................................................................................2-293
[750] VM CARD RESTART......................................................................................................2-295
[751] ASSIGN MAILBOX .........................................................................................................2-297
[752] AUTO RECORD .............................................................................................................2-298
[753] WARNING DESTINATION..............................................................................................2-300
[754] VM HALT ........................................................................................................................2-301
[755] VM ALARM .....................................................................................................................2-302
[756] ASSIGN VM MOH ..........................................................................................................2-303
[757] VM IN/OUT .....................................................................................................................2-305
[758] VM DAY/NIGHT ..............................................................................................................2-306
[759] CLI RINGING..................................................................................................................2-307
[760] ITEM COST TABLE ........................................................................................................2-310
[761] TAX RATE SETUP..........................................................................................................2-312
[762] ROOM COST RATE .......................................................................................................2-314
[800] ENABLE TECHNICIAN PROGRAM ...............................................................................2-315
[801] CHANGE TECHNICIAN PASSCODE .............................................................................2-317
[802] CUSTOMER ACCESS MMC NUMBER..........................................................................2-318
[803] ASSIGN TENANT GROUP .............................................................................................2-319
[804] SYSTEM I/O PARAMETER ............................................................................................2-320
XII
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[805] LEVEL AND GAIN.......................................................................................................... 2-323
[806] CARD PRE-INSTALL ..................................................................................................... 2-326
[807] PHONE VOLUME CONTROL........................................................................................ 2-328
[809] SYSTEM MMC LANGUAGE.......................................................................................... 2-330
[810] HALT PROCESSING ..................................................................................................... 2-331
[811] RESET SYSTEM............................................................................................................ 2-332
[812] SET COUNTRY CODE .................................................................................................. 2-333
[813] HOTEL OPERATION ..................................................................................................... 2-334
[815] CUSTOMER DATABASE COPY .................................................................................... 2-335
[816] CONFERENCE GAIN .................................................................................................... 2-337
[818] PROGRAM DOWNLOAD .............................................................................................. 2-339
[819] SMART MEDIA FILE CONTROL ................................................................................... 2-340
[820] ASSIGN SYSTEM LINK ID ............................................................................................ 2-342
[821] ASSIGN NETWORK TRUNK ......................................................................................... 2-343
[822] SET VIRTUAL EXTENSION TYPE ................................................................................ 2-344
[823] ASSIGN NETWORK COS.............................................................................................. 2-346
[824] NETWORK DIAL TRANSLATION .................................................................................. 2-348
[825] ASSIGN NETWORKING OPTION ................................................................................. 2-350
[826] ASSIGN SYSTEM REFERENCE CLOCK...................................................................... 2-352
[829] LAN PRINTER PARAMETER ........................................................................................ 2-353
[830] ETHERNET PARAMETERS .......................................................................................... 2-355
[831] MGI PARAMETERS ....................................................................................................... 2-358
[832] VOIP ACCESS CODE.................................................................................................... 2-360
[833] VoIP IP TABLE ............................................................................................................... 2-362
[834] H.323 OPTIONS ............................................................................................................ 2-364
[835] MGI DSP OPTIONS....................................................................................................... 2-366
[836] H.323 GK OPTIONS ...................................................................................................... 2-370
[837] SIP OPTIONS ................................................................................................................ 2-372
[838] PRIVATE IP ADDRESSES ............................................................................................. 2-375
[840] IP PHONE INFORMATION ............................................................................................ 2-376
[841] SYSTEM IP OPTIONS................................................................................................... 2-379
[844] IP STATION TYPE ......................................................................................................... 2-383
[845] WLAN PARAMETER...................................................................................................... 2-384
[846] WIP INFORMATION ...................................................................................................... 2-390
[847] WLAN RESET AND STATUS CHECK ........................................................................... 2-392
[848] WLAN IP/MAC LIST....................................................................................................... 2-393
[849] WLAN CONFIGURATION.............................................................................................. 2-394
[850] SYSTEM RESOURCE DISPLAY ................................................................................... 2-396
[851] ALARM REPORTING..................................................................................................... 2-397
© SAMSUNG Electronics Co., Ltd.
XIII
TABLE OF CONTENTS
[852] SYSTEM ALARM ASSIGNMENTS .................................................................................2-399
[853] MAINTENANCE BUSY...................................................................................................2-406
[854] DIAGNOSTIC TIME........................................................................................................2-408
[855] SYSTEM OPTIONS........................................................................................................2-409
[856] TECH PROGRAMMING LOGS ...................................................................................... 2-411
[858] ASSIGN SYSTEM EMERGENCY ALARM .....................................................................2-412
[859] HARDWARE VERSION DISPLAY..................................................................................2-413
[860] UCD STATUS SERVICE.................................................................................................2-415
[861] SYSTEM OPTIONS........................................................................................................2-416
[890] INITIALIZE PORT ...........................................................................................................2-418
ANNEX A. ABBREVIATION
A-1
A ~ D ......................................................................................................................................... A-1
E ~ I ......................................................................................................................................... A-2
K ~ P ......................................................................................................................................... A-3
Q ~ T ......................................................................................................................................... A-4
U ~ X ......................................................................................................................................... A-5
LIST OF FIGURES
Figure 1.1
DS-4028E Phone .....................................................................................................1-2
Figure 1.2
DS-5038D phone .....................................................................................................1-3
Figure 1.3
DS-5021D/ITP-5021D phone...................................................................................1-3
Figure 1.4
DS-5014D/ITP-5014D phone...................................................................................1-4
LIST OF TABLES
Table 2.1
XIV
Customer Set Relocation Allow Table......................................................................2-92
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide
CHAPTER 1. Overview of MMC
Programming
In this chapter, the things to know before you start MMC programming, and the phone
buttons and cautions will be discussed.
1.1 Introduction to Programming
The MMC program means the changes on the data that is used for the system operation
program. There are 3 levels of MMC programming, such as technician, operator, and
station levels. According to the programming level, the station can program or cannot
program the data change. The technician level programming and the operator level
programming require a passcode for each level while the station level programming does
not require a passcode.
Program List by User’s Level
For information about the programming level classified by user’s level, refer to
‘1.4 Program List by User’s Level’ of this chapter.
© SAMSUNG Electronics Co., Ltd.
1-1
CHAPTER 1. Overview of MMC Programming
1.2 Phone Buttons
There are several phones that are allowed for MMC programming; DS-4000 series
phones(DS-4028E, DS-4018E, DS-4008E), DS-5000D series phone(DS-5038D, DS-5021D,
DS-5014D) and ITP-5000D series phone(ITP-5021D, ITP-5014D)
1.2.1 DS-4000 Series phones
The following figure shows the shape of DS-4028E phone among DS-4000 series phones.
LCD Display
Left Soft Button Right Soft Button
A Button
B Button
Dial Buttons
Transfer Button
ANS/RLS Button
Hold Button
Volume Buttons
Speaker
Button
Figure 1.1 DS-4028E Phone
Among 3 Soft buttons, the first one is called the ‘Left Soft button’, which is used to save
the modified data or to move the cursor inside the LCD display in the left direction.
Among 3 Soft buttons, the third one is called the ‘Right Soft button’, which is used to save
the modified data or to move the cursor in the right direction.
Among 8 programmable buttons, the first 6 programmable buttons are assigned as ‘A~F’ to
carry out specific functions or usage while programming. Generally, these buttons perform
specific functions that you set for each corresponding button.
When MMC programming, other functions programmed on the programmable buttons are as
follows:
Volume buttons: Search the selected items.
Dial keypad: Confirm the status
Soft buttons: Move the cursor
Speaker Button: Save data and proceed to the next program
1-2
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Hold Button: Erase the previously entered item
A button: Select either a capital letter or small letter
B button: Select either a Korean character or English character
Transfer Button: Enter the programming code
1.2.2 DS/ITP-5000D Series Phones
There are several DS/ITP-5000D series phones, such as DS-5038D, DS-5021D, DS-5014D,
ITP-5021D, ITP-5014D as shown in the figures below:
LCD Display
Programmable Buttons(21)
Soft buttons
Scroll Button
Telephone Status Indicator
A Buttons
B Buttons
Volume Buttons
Redial Button
Programmable Buttons(17)
Dial Buttons
Microphone
Speaker Button
Conference Button
Hold Button
Transfer Button
Figure 1.2 DS-5038D phone
LCD Display
Programmable Buttons(21)
Soft buttons
Scroll Button
Telephone Status Indicator
Volume Buttons
Redial Button
Navigation Buttons
Dial Buttons
Microphone
Speaker Button
Conference Button
Hold Button
Transfer Button
Figure 1.3 DS-5021D/ITP-5021D phone
© SAMSUNG Electronics Co., Ltd.
1-3
CHAPTER 1. Overview of MMC Programming
LCD Display
Programmable Buttons(14)
Soft buttons
Scroll Button
Telephone Status Indicator
Volume Buttons
Redial Button
Navigation Buttons
Dial Buttons
Microphone
Speaker Button
Conference Button
Hold Button
Transfer Button
Figure 1.4 DS-5014D/ITP-5014D phone
The DS-5000D series phones have 38/21/14 programmable buttons that a station can
register any functions he/she wants to use. Also, there are several other function buttons:
the dial buttons, the volume button for controlling a voice volume, the redial button that
allows to redial the latest phone number, the conference button that can be used during the
conference, the transfer button that is used to transfer a call received during a phone
conversation to another station, the hold button to hold a call for a while, the speaker button,
and the navigation buttons that are designed for the convenience of phone users.
And, there is the LCD display that displays the station status and various other kinds of
information. With three colors like red, green, and yellow, the station status indicator
displays the current status of station.
1-4
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
1.3 Cautions in Programming
Programming can be done while the handset is placed on the phone at a idle state.
Programming can be done on any phone.
Programming can be done only on the phone, not on normal phone.
If the phone does not have the LCD display, press the numbers using the dial buttons
as instructed by the programming guide, without using the volume buttons. However,
if the phone does not have Soft buttons, certain programming cannot be done.
Therefore, only the station level programming is allowed on the phone that does not
have the LCD display.
If the LCD displays an ‘INVALID DATA’ message while programming, this means
that the entered data is invalid. Enter the correct data again.
The content of the displayed message for each step shows the status after each step is
executed.
If no key is pressed for a certain period of time during programming(Key program end
time, default is 60 seconds), it becomes a idle state from programming mode.
If the phone is off hook while programming, it becomes a dial state from programming
mode.
Before the modified data is confirmed by pressing [Left Soft] button or [Right Soft]
button, the [Speaker] or [Transfer] button is pressed to make it at a idle state or the phone
is unplugged. In this case, the data entered up to that time will be automatically saved
as the data displayed on the LCD.
© SAMSUNG Electronics Co., Ltd.
1-5
CHAPTER 1. Overview of MMC Programming
1.4 Program List by User’s Level
The MMC program can be divided into programmable one and non-programmable one.
The programmable MMC is classified into 3 levels, such as technician, operator, and
station level. In this section, the programmable MMC for each level will be introduced.
1.4.1 Station Level Programming
Programming can be done for only station level programs.
MMC Program No.
1-6
Program Description
MMC: 100
STATION LOCK
MMC: 101
CHANGE USER PASSCODE
MMC: 102
CALL FORWARD
MMC: 103
SET ANSWER MODE
MMC: 104
STATION NAME
MMC: 105
STATION SPEED DIAL
MMC: 106
STATION SPEED DIAL NAME
MMC: 107
KEY EXTENDER
MMC: 108
STATION STATUS
MMC: 109
DATE DISPLAY
MMC: 110
STATION ON/OFF
MMC: 111
PHONE RING TONE
MMC: 112
ALARM REMINDER CLOCK
MMC: 113
VIEW MEMO NUMBER
MMC: 114
PHONE VOLUME
MMC: 115
SET PROGRAMMED MESSAGE
MMC: 116
ALARM AND MESSAGE
MMC: 117
EDIT TEXT MESSAGE
MMC: 118
CONFERENCE GROUP
MMC: 119
CALLER ID DISPLAY
MMC: 120
LARGE LCD OPTION
MMC: 121
PHONE LANGUAGE
MMC: 122
NEWS DISPLAY SPEED
MMC: 125
EXECUTIVE STATE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
1.4.2 Operator Level Programming
An technician can do programming within the range set by the MMC [802] CUSTOMER
ACCESS MMC NUMBER
Programming is allowed for any phone within the tenant group, but it can be done for only
one phone at a time.
1.4.2.1 System Related MMC
The MMC programs related to the function of the system are as follows:
MMC Program No.
Program Description
MMC: 200
OPEN CUSTOMER PROGRAMMING
MMC: 201
CHANGE CUSTOMER PASSCODE
MMC: 202
CHANGE FEATURE PASSCODE
MMC: 203
ASSIGN UA DEVICE
MMC: 204
COMMON BELL CONTROL
MMC: 205
ASSIGN LOUD BELL
MMC: 206
BARGE-IN TYPE
MMC: 207
ASSIGN VM/AA PORT
MMC: 208
ASSIGN RING TYPE
MMC: 209
ASSIGN ADD-ON MODULE
MMC: 210
CUSTOMER ON/OFF PER TENANT
MMC: 211
DOOR RING ASSIGNMENT
MMC: 214
DISA ALARM RINGING STATION
MMC: 215
VOICE DIALLER OPTIONS
MMC: 216
VOICE DIALLER ASSIGNMENTS
MMC: 217
TRAFFIC REPORT OPTION
MMC: 220
ISDN SERVICE TYPE
MMC: 221
EXTENSION TYPE
MMC: 222
FAX PAIR
MMC: 224
WAKE-UP ANNOUNCEMENT
© SAMSUNG Electronics Co., Ltd.
1-7
CHAPTER 1. Overview of MMC Programming
1.4.2.2 Station Related MMC
The MMC programs related to the function of the station are as follows:
MMC Program No.
1-8
Program Description
MMC: 300
CUSTOMER ON/OFF PER STATION
MMC: 301
ASSIGN STATION COS
MMC: 302
PICKUP GROUPS
MMC: 303
ASSIGN BOSS/SECRETARY
MMC: 304
ASSIGN EXTENSION/TRUNK USE
MMC: 305
ASSIGN FORCED CODE
MMC: 306
HOT LINE/OFF HOOK SELECTION
MMC: 308
ASSIGN BACKGROUND MUSIC SOURCE
MMC: 309
ASSIGN STATION MOH SOURCE
MMC: 310
LCR CLASS OF SERVICE
MMC: 312
ALLOW CALLER ID
MMC: 314
CONFIRM OUTGOING CALL
MMC: 315
CUSTOMER SET RELOCATION
MMC: 316
COPY STN/TRK USE
MMC: 317
ASSIGN STATION/STATION USE
MMC: 318
DISTINCTIVE RINGING
MMC: 319
BRANCH GROUP
MMC: 320
PRESET FWD NO ANSWER
MMC: 323
CALLING PARTY NUMBER
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
1.4.2.3 Trunk Related MMC
The MMC programs related to the function of the trunk are as follows:
MMC Program No.
Program Description
MMC: 400
CUSTOMER ON/OFF PER TRUNK
MMC: 401
TRUNK LINE/PBX LINE
MMC: 402
TRUNK DIAL TYPE
MMC: 403
TRUNK TOLL CLASS
MMC: 404
TRUNK NAME
MMC: 405
TRUNK CO TEL NUMBER
MMC: 406
TRUNK RING ASSIGNMENT
MMC: 407
FORCED TRUNK RELEASE
MMC: 408
ASSIGN TRUNK MOH SOURCE
MMC: 409
TRUNK STATUS READ
MMC: 410
ASSIGN DISA TRUNK
MMC: 411
ASSIGN E1 SIGNAL TYPE
MMC: 412
ASSIGN TRUNK SIGNAL
MMC: 413
VMS CALL TYPE
MMC: 414
PRS SIGNAL
MMC: 415
REPORT TRUNK ABANDON DATA
MMC: 416
ASSIGN E & M/DID RINGDOWN
MMC: 417
E1/PRI CRC4 OPTION
MMC: 418
BRI AND PRI CARD RESTART
MMC: 419
BRI OPTIONS
MMC: 420
PRI OPTIONS
MMC: 421
MSN DIGIT
MMC: 422
TRUNK COS
MMC: 423
S/T MODE
MMC: 424
BRI S0 MAPPING
MMC: 425
ASSIGN CALLER ID TRUNKS
MMC: 426
TRUNK GAIN CONTROL
MMC: 428
ASSIGN TRUNK/TRUNK USE
MMC: 433
COST RATE
MMC: 434
CONNECTION STATUS
MMC: 436
TRUNK TMC GAIN
© SAMSUNG Electronics Co., Ltd.
1-9
CHAPTER 1. Overview of MMC Programming
1.4.2.4 Timer and Tone Related MMC
The MMC programs related to the function of the timer and tone are as follows:
MMC Program No.
Program Description
MMC: 500
SYSTEM-WIDE COUNTERS
MMC: 501
SYSTEM TIMERS
MMC: 502
STATION-WIDE TIMERS
MMC: 503
TRUNK-WIDE TIMER
MMC: 504
PULSE MAKE/BREAK RATIO
MMC: 505
ASSIGN DATE AND TIME
MMC: 506
TONE CADENCE
MMC: 507
ASSIGN RING PLAN TIME
MMC: 508
CALL COST
MMC: 510
SLI RING CADENCE
MMC: 511
MSG WAITING LAMP CADENCE
MMC: 512
HOLIDAY ASSIGNMENT
MMC: 513
HOTEL TIMER
MMC: 514
TONE SOURCE
MMC: 515
ASSIGN DAYLIGHT SAVING DATE
1.4.2.5 Group Related MMC
The MMC programs related to the function of a group are as follows:
MMC Program No.
1-10
Program Description
MMC: 600
ASSIGN OPERATOR GROUP
MMC: 601
ASSIGN STATION GROUP
MMC: 602
STATION GROUP NAME
MMC: 603
ASSIGN TRUNK GROUP
MMC: 604
ASSIGN STATION TO PAGE ZONE
MMC: 605
ASSIGN EXTERNAL PAGE ZONE
MMC: 606
ASSIGN SPEED BLOCK
MMC: 607
UCD OPTIONS
MMC: 608
ASSIGN REVIEW BLOCK
MMC: 609
CALL LOG BLOCK
MMC: 611
ALLOW TEXT MESSAGING
MMC: 612
ALLOW GROUP CONFERENCE
MMC: 614
STATION/TRUNK USE GROUP
MMC: 615
MGI GROUP
MMC: 616
MGI USER
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
1.4.2.6 Tables, Codes, AA, DECT and VM MMC
The MMC programs related to the function of the tables, codes, AA, DECT and VM are as
follows:
MMC Program No.
Program Description
MMC: 700
COPY COS CONTENTS
MMC: 701
ASSIGN COS CONTENTS
MMC: 702
TOLL DENY TABLE
MMC: 703
TOLL ALLOWANCE TABLE
MMC: 704
ASSIGN WILD CHARACTER
MMC: 705
ASSIGN SYSTEM SPEED DIAL
MMC: 706
SYSTEM SPEED DIAL BY NAME
MMC: 707
AUTHORIZATION CODE
MMC: 708
ACCOUNT CODE
MMC: 709
TOLL PASS CODE/SPECIAL CODE TABLE
MMC: 710
LCR DIGIT TABLE
MMC: 711
LCR TIME TABLE
MMC: 712
LCR ROUTE TABLE
MMC: 713
LCR MODIFY DIGIT TABLE
MMC: 714
DID NUMBER AND NAME TRANSLATION
MMC: 715
PROGRAMMED STATION MESSAGE
MMC: 716
UK LCR OPTIONS
MMC: 717
UCD AGENT ID
MMC: 718
MY AREA CODE
MMC: 719
IDLE DISPLAY
MMC: 720
COPY KEY PROGRAMMING
MMC: 721
SAVE STATION KEY PROGRAMMING
MMC: 722
STATION KEY PROGRAMMING
MMC: 723
SYSTEM KEY PROGRAMMING
MMC: 724
DIAL NUMBERING PLAN
MMC: 725
SMDR OPTIONS
MMC: 726
VM/AA OPTIONS
MMC: 727
SYSTEM VERSION DISPLAY
MMC: 728
CID TRANSLATION TABLE
MMC: 730
AA RECORD GAIN
MMC: 731
AA RAM CLEAR
MMC: 732
AA TRANSLATION TABLE
MMC: 733
AA PLAN TABLE
© SAMSUNG Electronics Co., Ltd.
1-11
CHAPTER 1. Overview of MMC Programming
MMC Program No.
1-12
Program Description
MMC: 734
AUTO ATTENDANT MESSAGE MATCH
MMC: 735
AA USE TABLE
MMC: 736
ASSIGN AA MOH
MMC: 737
DECT SYSTEM CODE
MMC: 738
DECT CLEAR REGISTRATION
MMC: 740
STATION PAIR
MMC: 741
DBS RESTART
MMC: 742
BSI STATUS
MMC: 743
DBS STATUS
MMC:744
DECT REGISTRATION ON/OFF
MMC: 745
BSI RF CARRIER
MMC: 746
COSTING DIAL PLAN
MMC: 747
RATE CALCULATION TABLE
MMC: 750
VM CARD RESTART
MMC: 751
ASSIGN MAILBOX
MMC: 752
AUTO RECORD
MMC: 753
WARNING DESTINATION
MMC: 754
VM HALT
MMC: 755
VM ALARM
MMC: 756
ASSIGN VM MOH
MMC: 757
VM IN/OUT
MMC: 758
VM DAY/NIGHT
MMC: 759
RING ASSIGNMENT BY CALLING PARTY NUMBER
MMC: 760
ITEM COST TABLE
MMC: 761
TAX RATE SETUP
MMC: 762
ROOM COST RATE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
1.4.3 Technician Level Programming
This level is allowed to program every level of program.
This level of programming can be done on every phone within the system, but it can be
done for only one phone at a time.
MMC Program No.
Program Description
MMC: 800
ENABLE TECHNICIAN PROGRAM
MMC: 801
CHANGE TECHNICIAN PASSCODE
MMC: 802
CUSTOMER ACCESS MMC NUMBER
MMC: 803
ASSIGN TENANT GROUP
MMC: 804
SYSTEM I/O PARAMETER
MMC: 805
LEVEL AND GAIN
MMC: 806
CARD PRE-INSTALL
MMC: 807
PHONE VOLUME CONTROL
MMC: 809
SYSTEM MMC LANGUAGE
MMC: 810
HALT PROCESSING
MMC: 811
RESET SYSTEM
MMC: 812
SET COUNTRY CODE
MMC: 813
HOTEL OPERATION
MMC: 815
CUSTOMER DATABASE COPY
MMC: 816
CONFERENCE GAIN
MMC: 818
PROGRAM DOWNLOAD
MMC: 819
SMART MEDIA FILE CONTROL
MMC: 820
ASSIGN SYSTEM LINK ID
MMC: 821
ASSIGN NETWORK TRUNK
MMC: 822
SET VIRTUAL EXTENSION TYPE
MMC: 823
ASSIGN NETWORK COS
MMC: 824
NETWORK DIAL TRANSLATION
MMC: 825
ASSIGN NETWORKING OPTION
MMC: 826
ASSIGN SYSTEM REFERENCE CLOCK
MMC: 829
LAN PRINTER PARAMETER
MMC: 830
ETHERNET PARAMETERS
MMC: 831
MGI PARAMETERS
MMC: 832
VOIP ACCESS CODE
MMC: 833
VoIP IP TABLE
MMC: 834
H.323 OPTIONS
MMC: 835
MGI DSP OPTIONS
MMC: 836
H.323 GK OPTIONS
MMC: 837
SIP OPTIONS
© SAMSUNG Electronics Co., Ltd.
1-13
CHAPTER 1. Overview of MMC Programming
MMC Program No.
1-14
Program Description
MMC: 838
PRIVATE IP ADDRESSES
MMC: 840
IP PHONE INFORMATION
MMC: 841
SYSTEM IP OPTIONS
MMC: 844
IP STATION TYPE
MMC: 845
WLAN PARAMETER
MMC: 846
WIP INFORMATION
MMC: 847
WLAN RESET AND STATUS CHECK
MMC: 848
WLAN IP/MAC LIST
MMC: 849
WLAN CONFIGURATION
MMC: 850
SYSTEM RESOURCE DISPLAY
MMC: 851
ALARM REPORTING
MMC: 852
SYSTEM ALARM ASSIGNMENTS
MMC: 853
MAINTENANCE BUSY
MMC: 854
DIAGNOSTIC TIME
MMC: 855
SYSTEM OPTIONS
MMC: 856
TECH PROGRAMMING LOGS
MMC: 858
ASSIGN SYSTEM EMERGENCY ALARM
MMC: 859
HARDWARE VERSION DISPLAY
MMC: 860
UCD STATUS SERVICE
MMC: 861
SYSTEM OPTIONS
MMC: 890
INITIALIZE PORT
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
1.5 Program List by Name
This program list is arranged alphabetically.
Program Description
MMC Program No.
AA PLAN TABLE
MMC: 733
AA RAM CLEAR
MMC: 731
AA RECORD GAIN
MMC: 730
AA TRANSLATION TABLE
MMC: 732
AA USE TABLE
MMC: 735
ACCOUNT CODE
MMC: 708
ALARM AND MESSAGE
MMC: 116
ALARM REMINDER CLOCK
MMC: 112
ALARM REPORTING
MMC: 851
ALLOW CALLER ID
MMC: 312
ALLOW GROUP CONFERENCE
MMC: 612
ALLOW TEXT MESSAGING
MMC: 611
ASSIGN AA MOH
MMC: 736
ASSIGN ADD-ON MODULE
MMC: 209
ASSIGN BACKGROUND MUSIC SOURCE
MMC: 308
ASSIGN BOSS/SECRETARY
MMC: 303
ASSIGN CALLER ID TRUNKS
MMC: 425
ASSIGN COS CONTENTS
MMC: 701
ASSIGN DATE AND TIME
MMC: 505
ASSIGN DAYLIGHT SAVING DATE
MMC: 515
ASSIGN DISA TRUNK
MMC: 410
ASSIGN E & M/DID RINGDOWN
MMC: 416
ASSIGN E1 SIGNAL TYPE
MMC: 411
ASSIGN EXTENSION/TRUNK USE
MMC: 304
ASSIGN EXTERNAL PAGE ZONE
MMC: 605
ASSIGN FORCED CODE
MMC: 305
ASSIGN LOUD BELL
MMC: 205
ASSIGN MAILBOX
MMC: 751
ASSIGN NETWORK COS
MMC: 823
ASSIGN NETWORK TRUNK
MMC: 821
ASSIGN NETWORKING OPTION
MMC: 825
ASSIGN OPERATOR GROUP
MMC: 600
ASSIGN REVIEW BLOCK
MMC: 608
© SAMSUNG Electronics Co., Ltd.
1-15
CHAPTER 1. Overview of MMC Programming
Program Description
1-16
MMC Program No.
ASSIGN RING PLAN TIME
MMC: 507
ASSIGN RING TYPE
MMC: 208
ASSIGN SPEED BLOCK
MMC: 606
ASSIGN STATION COS
MMC: 301
ASSIGN STATION GROUP
MMC: 601
ASSIGN STATION MOH SOURCE
MMC: 309
ASSIGN STATION TO PAGE ZONE
MMC: 604
ASSIGN STATION/STATION USE
MMC: 317
ASSIGN SYSTEM EMERGENCY ALARM
MMC: 858
ASSIGN SYSTEM LINK ID
MMC: 820
ASSIGN SYSTEM REFERENCE CLOCK
MMC: 826
ASSIGN SYSTEM SPEED DIAL
MMC: 705
ASSIGN TENANT GROUP
MMC: 803
ASSIGN TRUNK GROUP
MMC: 603
ASSIGN TRUNK MOH SOURCE
MMC: 408
ASSIGN TRUNK SIGNAL
MMC: 412
ASSIGN TRUNK/TRUNK USE
MMC: 428
ASSIGN UA DEVICE
MMC: 203
ASSIGN SYSTEM REFERENCE CLOCK
MMC: 826
ASSIGN SYSTEM REFERENCE CLOCK
MMC: 826
ASSIGN SYSTEM SPEED DIAL
MMC: 705
ASSIGN TENANT GROUP
MMC: 803
ASSIGN TRUNK GROUP
MMC: 603
ASSIGN TRUNK MOH SOURCE
MMC: 408
ASSIGN TRUNK SIGNAL
MMC: 412
ASSIGN TRUNK/TRUNK USE
MMC: 428
ASSIGN UA DEVICE
MMC: 203
ASSIGN VM MOH
MMC: 756
ASSIGN VM/AA PORT
MMC: 207
ASSIGN WILD CHARACTER
MMC: 704
AUTHORIZATION CODE
MMC: 707
AUTO ATTENDANT MESSAGE MATCH
MMC: 734
AUTO RECORD
MMC: 752
BARGE-IN TYPE
MMC: 206
BRANCH GROUP
MMC: 319
BRI AND PRI CARD RESTART
MMC: 418
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Program Description
MMC Program No.
BRI OPTIONS
MMC: 419
BRI S0 MAPPING
MMC: 424
BSI RF CARRIER
MMC: 745
BSI STATUS
MMC: 742
CALL COST
MMC: 508
CALL FORWARD
MMC: 102
CALL LOG BLOCK
MMC: 609
CALLER ID DISPLAY
MMC: 119
CALLING PARTY NUMBER
MMC: 323
CARD PRE-INSTALL
MMC: 806
CHANGE CUSTOMER PASSCODE
MMC: 201
CHANGE FEATURE PASSCODE
MMC: 202
CHANGE TECHNICIAN PASSCODE
MMC: 801
CHANGE USER PASSCODE
MMC: 101
CID TRANSLATION TABLE
MMC: 728
COMMON BELL CONTROL
MMC: 204
CONFERENCE GAIN
MMC: 816
CONFERENCE GROUP
MMC: 118
CONFIRM OUTGOING CALL
MMC: 314
CONNECTION STATUS
MMC: 434
COPY COS CONTENTS
MMC: 700
COPY KEY PROGRAMMING
MMC: 720
COPY STN/TRK USE
MMC: 316
COST RATE
MMC: 433
COSTING DIAL PLAN
MMC: 746
CUSTOMER ACCESS MMC NUMBER
MMC: 802
CUSTOMER DATABASE COPY
MMC: 815
CUSTOMER ON/OFF PER STATION
MMC: 300
CUSTOMER ON/OFF PER TENANT
MMC: 210
CUSTOMER ON/OFF PER TRUNK
MMC: 400
CUSTOMER SET RELOCATION
MMC: 315
DATE DISPLAY
MMC: 109
DBS RESTART
MMC: 741
DBS STATUS
MMC: 743
DECT CLEAR REGISTRATION
MMC: 738
DECT REGISTRATION ON/OFF
MMC:744
© SAMSUNG Electronics Co., Ltd.
1-17
CHAPTER 1. Overview of MMC Programming
Program Description
1-18
MMC Program No.
DECT SYSTEM CODE
MMC: 737
DIAGNOSTIC TIME
MMC: 854
DIAL NUMBERING PLAN
MMC: 724
DID NUMBER AND NAME TRANSLATION
MMC: 714
DISA ALARM RINGING STATION
MMC: 214
DISTINCTIVE RINGING
MMC: 318
DOOR RING ASSIGNMENT
MMC: 211
E1/PRI CRC4 OPTION
MMC: 417
EDIT TEXT MESSAGE
MMC: 117
ENABLE TECHNICIAN PROGRAM
MMC: 800
ETHERNET PARAMETERS
MMC: 830
EXECUTIVE STATE
MMC: 125
EXTENSION TYPE
MMC: 221
FAX PAIR
MMC: 222
FORCED TRUNK RELEASE
MMC: 407
H.323 GK OPTIONS
MMC: 836
H.323 OPTIONS
MMC: 834
HALT PROCESSING
MMC: 810
HARDWARE VERSION DISPLAY
MMC: 859
HOLIDAY ASSIGNMENT
MMC: 512
HOT LINE/OFF HOOK SELECTION
MMC: 306
HOTEL OPERATION
MMC: 813
HOTEL TIMER
MMC: 513
IDLE DISPLAY
MMC: 719
INITIALIZE PORT
MMC: 890
IP PHONE INFORMATION
MMC: 840
IP STATION TYPE
MMC: 844
ISDN SERVICE TYPE
MMC: 220
ITEM COST TABLE
MMC: 760
KEY EXTENDER
MMC: 107
LAN PRINTER PARAMETER
MMC: 829
LARGE LCD OPTION
MMC: 120
LCR CLASS OF SERVICE
MMC: 310
LCR DIGIT TABLE
MMC: 710
LCR MODIFY DIGIT TABLE
MMC: 713
LCR ROUTE TABLE
MMC: 712
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Program Description
MMC Program No.
LCR TIME TABLE
MMC: 711
LEVEL AND GAIN
MMC: 805
MAINTENANCE BUSY
MMC: 853
MGI DSP OPTIONS
MMC: 835
MGI GROUP
MMC: 615
MGI PARAMETERS
MMC: 831
MGI USER
MMC: 616
MSG WAITING LAMP CADENCE
MMC: 511
MSN DIGIT
MMC: 421
MY AREA CODE
MMC: 718
NETWORK DIAL TRANSLATION
MMC: 824
NEWS DISPLAY SPEED
MMC: 122
OPEN CUSTOMER PROGRAMMING
MMC: 200
PHONE LANGUAGE
MMC: 121
PHONE RING TONE
MMC: 111
PHONE VOLUME
MMC: 114
PHONE VOLUME CONTROL
MMC: 807
PICKUP GROUPS
MMC: 302
PRESET FWD NO ANSWER
MMC: 320
PRI OPTIONS
MMC: 420
PRIVATE IP ADDRESSES
MMC: 838
PROGRAM DOWNLOAD
MMC: 818
PROGRAMMED STATION MESSAGE
MMC: 715
PRS SIGNAL
MMC: 414
PULSE MAKE/BREAK RATIO
MMC: 504
REPORT TRUNK ABANDON DATA
MMC: 415
RESET SYSTEM
MMC: 811
RING ASSIGNMENT BY CALLING PARTY NUMBER
MMC: 759
ROOM COST RATE
MMC: 762
S/T MODE
MMC: 423
SAVE STATION KEY PROGRAMMING
MMC: 721
SET ANSWER MODE
MMC: 103
SET COUNTRY CODE
MMC: 812
SET PROGRAMMED MESSAGE
MMC: 115
SET VIRTUAL EXTENSION TYPE
MMC: 822
SIP OPTIONS
MMC: 837
© SAMSUNG Electronics Co., Ltd.
1-19
CHAPTER 1. Overview of MMC Programming
Program Description
1-20
MMC Program No.
SLI RING CADENCE
MMC: 510
SMART MEDIA FILE CONTROL
MMC: 819
SMDR OPTIONS
MMC: 725
STATION GROUP NAME
MMC: 602
STATION KEY PROGRAMMING
MMC: 722
STATION LOCK
MMC: 100
STATION NAME
MMC: 104
STATION ON/OFF
MMC: 110
STATION PAIR
MMC: 740
STATION SPEED DIAL
MMC: 105
STATION SPEED DIAL NAME
MMC: 106
STATION STATUS
MMC: 108
STATION/TRUNK USE GROUP
MMC: 614
STATION-WIDE TIMERS
MMC: 502
SYSTEM ALARM ASSIGNMENTS
MMC: 852
SYSTEM I/O PARAMETER
MMC: 804
SYSTEM IP OPTIONS
MMC: 841
SYSTEM KEY PROGRAMMING
MMC: 723
SYSTEM MMC LANGUAGE
MMC: 809
SYSTEM OPTIONS
MMC: 855
SYSTEM OPTIONS
MMC: 861
SYSTEM RESOURCE DISPLAY
MMC: 850
SYSTEM SPEED DIAL BY NAME
MMC: 706
SYSTEM TIMERS
MMC: 501
SYSTEM VERSION DISPLAY
MMC: 727
SYSTEM-WIDE COUNTERS
MMC: 500
TAX RATE SETUP
MMC: 761
TECH PROGRAMMING LOGS
MMC: 856
TOLL ALLOWANCE TABLE
MMC: 703
TOLL DENY TABLE
MMC: 702
TOLL PASS CODE/SPECIAL CODE TABLE
MMC: 709
TONE CADENCE
MMC: 506
TONE SOURCE
MMC: 514
TRAFFIC REPORT OPTION
MMC: 217
TRUNK CO TEL NUMBER
MMC: 405
TRUNK COS
MMC: 422
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Program Description
MMC Program No.
TRUNK DIAL TYPE
MMC: 402
TRUNK GAIN CONTROL
MMC: 426
TRUNK LINE/PBX LINE
MMC: 401
TRUNK NAME
MMC: 404
TRUNK RING ASSIGNMENT
MMC: 406
TRUNK STATUS READ
MMC: 409
TRUNK TMC GAIN
MMC: 436
TRUNK TOLL CLASS
MMC: 403
TRUNK-WIDE TIMER
MMC: 503
UCD AGENT ID
MMC: 717
UCD OPTIONS
MMC: 607
UCD STATUS SERVICE
MMC: 860
UK LCR OPTIONS
MMC: 716
VIEW MEMO NUMBER
MMC: 113
VM ALARM
MMC: 755
VM CARD RESTART
MMC: 750
VM DAY/NIGHT
MMC: 758
VM HALT
MMC: 754
VM IN/OUT
MMC: 757
VM/AA OPTIONS
MMC: 726
VMS CALL TYPE
MMC: 413
VOICE DIALLER ASSIGNMENTS
MMC: 216
VOICE DIALLER OPTIONS
MMC: 215
VOIP ACCESS CODE
MMC: 832
VoIP IP TABLE
MMC: 833
WAKE-UP ANNOUNCEMENT
MMC: 224
WARNING DESTINATION
MMC: 753
WIP INFORMATION
MMC: 846
WLAN CONFIGURATION
MMC: 849
WLAN IP/MAC LIST
MMC: 848
WLAN PARAMETER
MMC: 845
WLAN RESET AND STATUS CHECK
MMC: 847
© SAMSUNG Electronics Co., Ltd.
1-21
CHAPTER 1. Overview of MMC Programming
1.6 Program List by Function
This section describes MMC programs are classified by the function of the OfficeServ 500.
1.6.1 Phone Function
The MMC programs related to the function of a phone that is connected with the
OfficeServ 500 are as follows:
MMC Program No.
1-22
Program Description
MMC: 100
STATION LOCK
MMC: 101
CHANGE USER PASSCODE
MMC: 102
CALL FORWARD
MMC: 103
SET ANSWER MODE
MMC: 104
STATION NAME
MMC: 105
STATION SPEED DIAL
MMC: 106
STATION SPEED DIAL NAME
MMC: 107
KEY EXTENDER
MMC: 108
STATION STATUS
MMC: 109
DATE DISPLAY
MMC: 110
STATION ON/OFF
MMC: 111
PHONE RING TONE
MMC: 112
ALARM REMINDER CLOCK
MMC: 114
PHONE VOLUME
MMC: 115
SET PROGRAMMED MESSAGE
MMC: 116
ALARM AND MESSAGE
MMC: 119
CALLER ID DISPLAY
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
1.6.2 Networking Function
The MMC programs related to the function of networking are as follows:
MMC Program No.
Program Description
MMC: 820
ASSIGN SYSTEM LINK ID
MMC: 821
ASSIGN NETWORK TRUNK
MMC: 822
SET VIRTUAL EXTENSION TYPE
MMC: 823
ASSIGN NETWORK COS
MMC: 824
NETWORK DIAL TRANSLATION
MMC: 825
ASSIGN NETWORKING OPTION
MMC: 829
LAN PRINTER PARAMETER
MMC: 830
ETHERNET PARAMETERS
MMC: 837
SIP OPTIONS
MMC: 840
IP PHONE INFORMATION
MMC: 841
SYSTEM IP OPTIONS
MMC: 844
IP STATION TYPE
1.6.3 VoIP Function
The MMC programs related to the function of VoIP(Voice over Internet Protocol) are as
follows:
MMC Program No.
Program Description
MMC: 831
MGI PARAMETERS
MMC: 832
VOIP ACCESS CODE
MMC: 833
VoIP IP TABLE
MMC: 834
H.323 OPTIONS
MMC: 835
MGI DSP OPTIONS
MMC: 836
H.323 GK OPTIONS
© SAMSUNG Electronics Co., Ltd.
1-23
CHAPTER 1. Overview of MMC Programming
1.6.4 WLAN Function
The MMC programs related to the function of WLAN(Wireless Local Area Network) are
as follows:
MMC Program No.
Program Description
MMC: 845
WLAN PARAMETER
MMC: 846
WIP INFORMATION
MMC: 847
WLAN RESET AND STATUS CHECK
MMC: 848
WLAN IP/MAC LIST
MMC: 849
WLAN CONFIGURATION
1.6.5 LCR Function
The MMC programs related to the function of LCR(Least Cost Routing) are as follows:
MMC Program No.
Program Description
MMC: 710
LCR DIGIT TABLE
MMC: 711
LCR TIME TABLE
MMC: 712
LCR ROUTE TABLE
MMC: 713
LCR MODIFY DIGIT TABLE
1.6.6 Auto Attendant/Voice Mail Function
The MMC programs related to the function of AA(Auto Attendant) or VM(Voice Mail) are
as follows:
MMC Program No.
1-24
Program Description
MMC: 207
ASSIGN VM/AA PORT
MMC: 215
VOICE DIALLER OPTIONS
MMC: 216
VOICE DIALLER ASSIGNMENTS
MMC: 413
VMS CALL TYPE
MMC: 726
VM/AA OPTIONS
MMC: 730
AA RECORD GAIN
MMC: 731
AA RAM CLEAR
MMC: 732
AA TRANSLATION TABLE
MMC: 733
AA PLAN TABLE
MMC: 734
AUTO ATTENDANT MESSAGE MATCH
MMC: 735
AA USE TABLE
MMC: 736
ASSIGN AA MOH
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
MMC Program No.
Program Description
MMC: 750
VM CARD RESTART
MMC: 751
ASSIGN MAILBOX
MMC: 752
AUTO RECORD
MMC: 753
WARNING DESTINATION
MMC: 754
VM HALT
MMC: 755
VM ALARM
MMC: 756
ASSIGN VM MOH
MMC: 757
VM IN/OUT
MMC: 758
VM DAY/NIGHT
1.6.7 Diagnosis Function
The MMC programs related to the function of diagnosing the system are as follows:
MMC Program No.
Program Description
MMC: 434
CONNECTION STATUS
MMC: 851
ALARM REPORTING
MMC: 852
SYSTEM ALARM ASSIGNMENTS
MMC: 853
MAINTENANCE BUSY
MMC: 854
DIAGNOSTIC TIME
MMC: 855
SYSTEM OPTIONS
MMC: 890
INITIALIZE PORT
1.6.8 Hotel Function
The MMC programs related to the function of a hotel are as follows:
MMC Program No.
Program Description
MMC: 217
TRAFFIC REPORT OPTION
MMC: 221
EXTENSION TYPE
MMC: 433
COST RATE
MMC: 513
HOTEL TIMER
MMC: 746
COSTING DIAL PLAN
MMC: 747
RATE CALCULATION TABLE
MMC: 760
ITEM COST TABLE
MMC: 761
TAX RATE SETUP
MMC: 762
ROOM COST RATE
© SAMSUNG Electronics Co., Ltd.
1-25
CHAPTER 1. Overview of MMC Programming
This page is intentionally left blank.
1-26
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide
CHAPTER 2. MMC Programming
This chapter describes how to use each MMC program as it was listed.
2.1 Overview of Programming Procedure
Here, the order of programming will be discussed before explaining programming method
of each list. Please read the description carefully before programming.
The programming order is as follows:
1) Make the programmable state.
Press the Transfer button at pause.
Enter the program number, either 200 or 800.
Enter either the operator passcode or the technician passcode.
Press 1 dial button to ‘enable’ the programming mode.
In case of Program 800 Technician Program Mode Setting, enter the tenant number
to be programmed.
2) Make the program number selectable state.
If the Speaker button is pressed, the program selection mode appears.
Or, if the Transfer button is pressed, the programming state ends and the pause state
begin.
3) Select a program.
Enter the program number.
Or, select the program number with the Volume button and press the Speaker button.
Or, Press Transfer button in a pause state and enter the program number.
4) Start programming the corresponding program.
© SAMSUNG Electronics Co., Ltd.
2-1
CHAPTER 2. MMC Programming
2.2 Programming Procedure
This section describes a procedure of each program. Refer to the programming procedure
corresponding to the MMC.
[100] STATION LOCK
Allows the system administrator or technician to lock or unlock an individual station or all
stations simultaneously. The three options are as follows:
No
Type
0
UNLOCKED
1
LOCKED OUT
Description
Unlocks a locked station.
The phone cannot make calls outside the system. It can however make
and receive intercom calls and receive incoming Trunk Line calls. When
in this mode the Hold button of the phone will flash slow RED.
2
LOCKED ALL
The phone cannot make or receive any calls. When in this mode the
Hold button of the phone will light steady RED.
CONDITIONS
Check if the station lock function is disabled at ‘MMC 301 ASSIGN STATION COS’.
If so, the station cannot be locked, but a locked station can be unlocked.
A station can be locked or unlocked under any condition when the station is in Operator
Level Programming or Technician Level Programming.
DEFAULT DATA
ALL STATIONS UNLOCKED
ACTION
2-2
DISPLAY
1. Press Transfer button and enter 100.
Display shows:
[201] STN LOCK
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and use
Right Soft button to move cursor.
OR
Press ANS/RLS button to select all stations.
[205] STN LOCK
3. Enter 0 to unlock or 1 to lock.(e.g., 1)
OR
Press Volume button to make selection and
press Right Soft button to return to step 2.
[205] STN LOCK
UNLOCKED
UNLOCKED
[ALL] STN LOCK
?
LOCKED OUT
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
4. Press Transfer button and enter to save and exit.
OR
Press Speaker button to save and advance to next MMC.
RELATED ITEMS
MMC 101
MMC 301
MMC 701
© SAMSUNG Electronics Co., Ltd.
CHANGE USER PASSCODE
ASSIGN STATION COS
ASSIGN COS CONTENTS
2-3
CHAPTER 2. MMC Programming
[101] CHANGE USER PASSCODE
Allows the system administrator or technician to reset any phone’s passcode to its default
value of ‘1234 . This MMC cannot display station passcodes; it can only reset them to
default.
Phone users can set or change their individual passcodes. The passcode is used to lock or
unlock the phone for toll restriction(call barring) override and to access the DISA feature.
CONDITIONS
The passcode of a station performing Operator Level Programming or Technician
Level Programming cannot be changed while the program mode is ‘ENABLE’.
An Operator or Technician Level can only delete the passcode of a station and reset the
passcode to the default value, ‘1234 , not permitting to know the passcode.
Default passcodes
Default passcodes cannot be used for toll restriction override or for DISA access.
DEFAULT DATA
ALL STATION PASSCODES: 1234
ACTION
DISPLAY
1. Press Transfer button and enter 101.
Display shows:
[201] PASSCODE
2. Dial phone number.(e.g., 205)
OR
Use Volume button to scroll through phone numbers
and press Right Soft button to move the cursor right.
[205] PASSCODE
3. Press Hold to reset passcode.
[205] PASSCODE
PASSCODE:****
PASSCODE:****
PASSCODE:1234
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 100
2-4
STATION LOCK
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[102] CALL FORWARD
Allows the system administrator to program the call forward destinations for other station
users. This MMC also allows call forward to be set after the destination has been entered.
Allows several types of call forwarding: FORWARD ALL, FORWARD NO ANSWER,
FORWARD BUSY and FOWRARD DND. There is an additional option, FORWARD
BUSY/NO ANSWER, that allows both of these options to be activated at the same time,
provided that destinations have been entered for both.
All types forwarding can be set external number.
No
Type
0
FORWARD CANCEL
1
FORWARD ALL CALL
2
FORWARD BUSY
3
FORWARD NO ANSWER
4
FORWARD BUSY/NO ANSWER
5
FORWARD DND
CONDITIONS
When ‘FORWARD BUSY/NO ANSWER’ is selected, calls are forwarded to stations
set at ‘FORWARD BUSY’ and ‘FORWARD NO ANSWER’. Thus, the destination
number must be set for both ‘FORWARD BUSY’ and ‘FORWARD NO ANSWER’ to
select ‘FORWARD BUSY/NO ANSWER’.
If the ‘FORWARD’ is set to ‘OFF’ at ‘MMC 701 ASSIGN COS CONTENTS’, call
forward cannot be set but can be canceled.(Default: ‘OFF’)
The ‘FORWARD’ and ‘EXT FWD’ must both be set to ‘ON’ at ‘MMC 701 ASSIGN
COS CONTENTS’ in order to forward a call to an external number. If only the
‘FORWARD’ is set to ‘ON’, calls can only be forwarded to internal numbers.(Default:
‘OFF’)
DEFAULT DATA
NONE
© SAMSUNG Electronics Co., Ltd.
2-5
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 102.
Display shows:
[201] FORWARD
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
[205] FORWARD
3. Dial 0-5 to select forward type.
OR
Press Volume button to select forward type and
press Right Soft button to move cursor.
[205] FORWARD
4. Dial destination number.(e.g., 201)
OR
Press Volume button to select destination and
press Right Soft button to move cursor.
[205] FORWARD
5. Dial 1 for YES, 0 for NO.
OR
Press Volume button to select YES or NO and
press Right Soft button to return to step 2.
[205] FORWARD
0:FORWARD CANCEL
0:FORWARD CANCEL
1:ALL CALL:NONE
1:ALL CALL:201
CURRENTLY SET :YES
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance to next MMC.
RELATED ITEMS
MMC 301
MMC 501
MMC 502
MMC 701
MMC 722
MMC 723
2-6
ASSIGN STATION COS
SYSTEM TIMERS
STATION TIMERS
ASSIGN COS CONTENTS
STATION KEY PROGRAMMING
SYSTEM KEY PROGRAMMING
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[103] SET ANSWER MODE
Allows the system administrator to change the answer mode of any phone.
Each phone can have its answer mode set to one of the following options:
No
0
Type
RING MODE
Description
The phone will ring in one of eight custom ring patterns.
Calls are answered by pressing the ANS/RLS Button or by
lifting the handset.
1
AUTO ANSWER MODE
After giving a short attention tone, the phone will
automatically answer calls on the speakerphone. When a
Trunk line is transferred to a phone in Auto Answer, the
screened portion of the call will be Auto Answer, but the
phone will ring when the transfer is complete if you have not
pressed the ANS/RLS Button or lifted the handset.
2
VOICE ANNOUNCE
The phone will not ring. After a short attention tone, callers
can make an announcement but the ANS/RLS Button or
handset must be used to answer calls.
CONDITIONS
Since the DS-12B digital phone is not equipped with a microphone, the phone operates in
voice announcement mode when a call arrives while set to auto answer mode. Users must
use the handset to reply to the caller.
DEFAULT DATA
ALL PHONES: RING
ACTION
DISPLAY
1. Press Transfer button and enter 103.
Display shows:
[201] ANS MODE
2. Dial phone number.(e.g., 205)
OR
Press Volume button to select phone and press
Right Soft button to move cursor.
OR
Press ANS/RLS button to select all.
[205] ANS MODE
3. Dial 0, 1 or 2 to change ring mode.
OR
Press Volume button to select ring mode and
press Right Soft button to return to step 2 above.
[205] ANS MODE
© SAMSUNG Electronics Co., Ltd.
RING MODE
RING MODE
[ALL] ANS MODE
?
VOICE ANNOUNCE
2-7
CHAPTER 2. MMC Programming
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 111
2-8
PHONE RING TONE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[104] STATION NAME
Allows the system administrator or technician to enter an 11-character name to identify an
individual station.
CONDITIONS
NONE
INPUT CHARACTERS
Names are written using the keypad. Each key press selects a character. Pressing the dial
pad key moves the cursor to the next position. For example, if the directory name is ‘SAM
SMITH,’ press the number ‘7 four times to get the letter ‘S’. Now press the number ‘2
once to get the letter ‘A’. Continue selecting characters from the table below to complete
your message. Pressing ‘A’ button will change the letter from upper case to lower case.
When the character you want appears on the same dial pad key as the previous
character, press the Volume Up button to move the cursor to the right.
COUNT
1
2
3
4
5
DIAL 0
<
>
.
)
0
DIAL 1
Space
?
,
!
1
DIAL 2
A
B
C
@
2
DIAL 3
D
E
F
#
3
DIAL 4
G
H
I
$
4
DIAL 5
J
K
L
%
5
DIAL 6
M
N
O
^
6
DIAL 7
P
Q
R
S
7
DIAL 8
T
U
V
*
8
DIAL 9
W
X
Y
Z
9
DIAL *
:
=
[
]
*
The # button can be used for the following special characters:
#, space, &, !, : , ?, ., ,, %, $, -, <, >, /, = , [, ], @, ^, (, ), _, +, {, }, |, ; , ”,
, ’, \.
DEFAULT DATA
NONE
© SAMSUNG Electronics Co., Ltd.
2-9
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 104.
Display shows:
[201] STN NAME
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
[205] STN NAME
3. Enter the station name using the procedure
described above and press Right Soft button to
return to step 2.
[205] STN NAME
_
SAM SMITH
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-10
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[105] STATION SPEED DIAL
Allows the system administrator or technician to program the personal speed dial locations
assigned to a station. This must be done for single line telephones because these stations
cannot access programming.
CONDITIONS
Each station may have up to 50 locations or bins assigned to it in MMC 606 Assign Speed
Block. The speed dial bins are numbered 00~49. Each speed dial number consists of a
trunk or trunk group access code followed by a separator and up to 24 digits to be dial.
These dial digits may consist of 0~9, * and #. If the system recognizes a valid trunk or
trunk group access number, it will automatically insert the separator.
DEFAULT DATA
NONE
PROGRAM BUTTONS
B
C
D
E
F
Used to insert a flash code ‘F’
Used to insert a pause code ‘P’
Used to insert a pulse/tone conversion code ‘C’
Used to mask/unmask following digits(shows as ‘[’ or ‘]’)
Used to enter name for speed dial bin(see MMC 106)
ACTION
DISPLAY
1. Press Transfer button and enter 105.
Display shows:
[201] SPEED DIAL
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
If selected station has no speed dial bins,
the display will be as shown and a new station may
be selected.
[205] SPEED DIAL
3. Dial location number.(e.g., 05)
OR
Press Volume button to select location and press
Right Soft button to move cursor.
[205] SPEED DIAL
© SAMSUNG Electronics Co., Ltd.
00:
00:
[205] SPEED DIAL
SPDBLK NOT EXIST
05:_
2-11
CHAPTER 2. MMC Programming
4. Enter trunk access code(e.g., 9) followed by
the number to be dialed.(e.g., 4264100)
OR
Press Right Soft button to return to step 2.
OR
Press Left Soft button to return to step 3.
Press Hold button to clear an entry.
If an error is made, use DOWN arrow to step back.
[205] SPEED DIAL
05:9-4264100_
5. Press ‘F’ button to access MMC 106 Station.
Speed Dial Name.
OR
Press Transfer button and enter to save and exit.
OR
Press Speaker button to save and advance to next MMC.
RELATED ITEMS
MMC106
MMC606
2-12
STATION SPEED DIAL NAME
ASSIGN SPEED BLOCK
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[106] STATION SPEED DIAL NAME
Allows an 11-character name to be entered for each personal speed dial location. This name
enables the speed dial number to be located when the directory dial feature is used.
The directory dial feature allows the display phone user to select a speed dial location by
viewing its name.
CONDITIONS
NONE
INPUT CHARACTERS
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 106.
Display shows:
[201] SPEED NAME
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
If selected station has no speed dial bins, the
display will be as shown and a new station may
be selected.
[205] SPEED NAME
3. Dial speed dial location.(e.g., 01)
OR
Press Volume button to scroll through location
numbers and press Right Soft button to move cursor.
[205] SPEED NAME
4. Enter the location name using the procedure
described above and press Right Soft button to
return to step 2.
[205] SPEED NAME
00:
00:
[305] SPEED NAME
SPDBLK NOT EXIST
01:_
01:SAM SMITH
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 105
MMC 606
© SAMSUNG Electronics Co., Ltd.
STATION SPEED DIAL
ASSIGN SPEED BLOCK
2-13
CHAPTER 2. MMC Programming
[107] KEY EXTENDER
Use this program to view the programmable buttons assigned to phone station.
In addition, it allows the system administrator to assign key extenders to some keys that
will make a general access feature key more specific. The feature keys that can have
extenders are listed below.
Feature
Extender
AB
Absence(extension number)
ACC
Account code bin(000-999)
BOSS
Boss and Secretary(1-4)
CR
VM Call Record
CS
UCD Call Status(UCD group number)
DIR
Directory dial by name type(1-3)
DP
Direct Pickup(extension or station group number)
DS
Direct Station Select(station number)
FWRD
Call Forward(0-7)
GPIK
Group Pickup(01-99)
IG
IN/Out of Group(station group number)
MMPG
Meet Me Page(0-9, * )
MW
Message Waiting(extension or station group number)
PAGE
Page(0-9, * )
PARK
Park Orbits(0-9)
RP
Ring Plan(1-6)
RSV
Room Status View(1-5)-Available in Hotel/Motel enabled only
SG
Station Group(station group number)
PMSG
Programmed Station Messaging(01-20)
SP
UCD Supervisor(UCD group number)
SPD
Speed Dial(00-49, 500-999)
VG
SVM-800 Group Message(station group number)
VM
VM Memo(extension or station group number)
VT
Voice Transfer(VM group number)
When the Right Soft button will not move the cursor to the right, you are
attempting to add an extender to a key that cannot have one.
2-14
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
CONDITIONS
NONE
DEFAULT DATA
<24 Button Digital Phone>
CALL1
CALL1
CALL2
CALL1
DT701
CALL1
DT702
CALL1
DT703
CALL1
DT704
CALL1
DT705
CALL1
DTl706
CALL1
DT7017
CALL1
DT708
CALL1
DT709
CALL1
DT7010
CALL1
DT711
CALL1
DT712
CALL1
DT713
CALL1
DT714
CALL1
DT715
CALL1
DT716
CALL1
CONF
CALL1
SPD
CALL1
NONE
CALL1
PAGE
CALL1
CBK
CALL1
GPIK01
CALL1
48 Butoon AOM
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
CALL1
DS
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
© SAMSUNG Electronics Co., Ltd.
2-15
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 107.
Display shows first station:
[201] EXT (MAST)
2. Dial station number.(e.g., 205)
OR
Use Volume button to scroll through station numbers
and press Right Soft button to move the cursor.
[205] EXT (MAST)
3. Press Right Soft button to program the phone.
[201] EXT (MAST)
OR
Use Volume button to scroll through the phone and
AOM’s and use Right Soft button to move the cursor.
4. Enter key number.(e.g., 18)
OR
Use Volume button to scroll through keys and use
Right Soft button to move the cursor.
OR
Press the key to be programmed Dial extender
according to above table.
System will return to this step If no more entries,
press Left Soft button to return to step 2.
01:CALL1
01:CALL1
01:CALL1
[201] EXT (AOM1)
01:DS
[205] EXT (MAST)
18:DS
[205] EXT (MAST)
18:DS207
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 720
MMC 721
MMC 722
MMC 723
MMC 724
2-16
COPY KEY PROGRAMMING
SAVE STATION KEY PROGRAMMING
STATION KEY PROGRAMMING
SYSTEM KEY PROGRAMMING
DIAL NUMBERING PLAN
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[108] STATION STATUS
Displays the following attributes of a station port. This is a READ-ONLY MMC:
No
Status
Description
0
PORT #
Cabinet(1~3)/Slot(1~9)/Port(1~16)
1
TYPE
Phone Type
2
PICKUP GROUP
None, 01~99
3
SGR
Station Group Number
4
BOSS-SECR
None, 1-4
5
PAGE
None, Page Zone(0~4, * )
6
COS NO
COS(1-30) per Ring Plan(01-06)
9
TENANT GROUP
Tenant Group Number(1~2)
CONDITIONS
NONE
DEFAULT DATA
PORT #: FOLLOWS HARDWARE POSITION
TYPE: DEPENDENT ON CONNECTED PHONE
PICKUP GRP: NONE
SGR: NONE
BOSS-SECR: NONE
PAGE ZONE: NONE
COS NUMBER: 01 IN ALL RING PLANS
TENANT GRP: 1
ACTION
DISPLAY
1. Press Transfer button and enter 108.
Display shows first station:
[201] STN STATUS
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
[205] STN STATUS
3. Dial 0~9 to select station status type.
OR
Press Volume button to select status and press.
Right Soft button to return to step 2.
[205] STN STATUS
© SAMSUNG Electronics Co., Ltd.
PORT:C1-S3-P01
PORT:C1-S3-P05
PICKUP GROUP:01
2-17
CHAPTER 2. MMC Programming
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 301
MMC 302
MMC 303
MMC 601
MMC 604
2-18
ASSIGN STATION COS
PICKUP GROUPS
ASSIGN BOSS/SECRETARY
ASSIGN STATION GROUP
ASSIGN STATION TO PAGE ZONE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[109] DATE DISPLAY
Allows the system administrator or technician to select the date and time display mode on a
per-station basis or system-wide.
No
0
1
2
Mode
COUNTRY
CLOCK
DISPLAY
Description
Sets overall display format and has two options:
0 = ORIENTAL
MM/DD
1 = WESTERN
DAY DD MON
DAY
HH:MM
HH:MM
Sets format of clock display and has two options:
0 = 12 HOUR
Displays 1 P.M. as 01:00
1 = 24 HOUR
Displays 1 P.M. as 13:00
Sets format of DAY and MON display and has two options:
0 = UPPER CASE
Displays Friday as FRI and March as MAR
1 = LOWER CASE
Displays Friday as Fri and March as Mar
CONDITIONS
NONE
DEFAULT DATA
COUNTRY: WESTERN
CLOCK: 12 HOUR
DISPLAY: LOWER CASE
ACTION
DISPLAY
1. Press Transfer button and enter 109.
Display shows:
[201] DAY FORMAT
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
OR
Press ANS/RLS button for all phones.
[205] DAY FORMAT
3. Dial 0~2 to select mode.
OR
Press Volume button to scroll through modes and
press Right Soft button to move cursor.
[205] DAY FORMAT
© SAMSUNG Electronics Co., Ltd.
COUNTRY:WESTERN
COUNTRY:WESTERN
[ALL] DAY FORMAT
COUNTRY:?
COUNTRY:ORIENTAL
2-19
CHAPTER 2. MMC Programming
4. Press Volume button to scroll through formats and
press Right Soft button to return to step 2.
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 505
2-20
ASSIGN DATE AND TIME
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[110] STATION ON/OFF
Allows the system administrator to set any of the phone features listed below.
No
Feature
00
AUTO HOLD
Default
OFF
Description
Automatically places an existing Trunk Line call on hold if
a CALL button, trunk key or trunk route key is pressed
during that call.
01
AUTO TIMER
ON
Automatically starts the stopwatch timer during a Trunk
Line call.
02
HEADSET USE
OFF
When ON, this feature disables the hook switch allowing
a headset user to answer all calls by pressing the
ANS/RLS button.
03
HOT KEYPAD
ON
When ON, this feature allows you to dial directory
numbers without having to first lift the handset or press
the Speaker button.
04
KEY TONE
ON
Allows you to hear a slight tone when pressing buttons
on phone.
05
PAGE REJOIN
ON
Allows you to hear the latter part of page announcements
if phone becomes free during a page.
06
RING PREF.
ON
When OFF, requires you to press the fast flashing button
to answer a ringing call after lifting the handset.
07
CALL COST
OFF
When ON, the cost of the call in progress will show in the
upper right corner of the phone display instead of
duration of the call.
08
AUTO CAMPON
OFF
When ON, phone users can allow intercom calls to camp-on
to other phones without having to press a CAMP-ON key.
09
AME BGM
OFF
This feature selects whether a station using Answer
Machine Emulation will hear their personal greeting or
BGM while callers are listening to the personal greeting.
A BGM source must be selected for this to work.
10
AME
OFF
PASSCODE
11
DISP SPDNAME
When ON, station users who have AME set must enter
their station password to listen to messages being left.
OFF
When ON, the speed dial name associated with a speed
dial number is displayed on a phone equipped a LCD
display when using speed dial.
12
CID REVW ALL
ON
When ON, saves information on all calls that ring at an
extension, When OFF, saves information only on calls
that were not answered at the extension or by voice mail.
13
SECURE OHVA
ON
When ON, OHVA announcements will be heard on the
handset. When OFF, OHVA announcements will be heard
over the phone speaker.
© SAMSUNG Electronics Co., Ltd.
2-21
CHAPTER 2. MMC Programming
No
Feature
Default
14
NOT CONT.CID
ON
Description
When OFF, the Caller ID will be continue display after the
phone user answered call.
15
AUTO ANS CO
OFF
When On, the incoming CO call will be answered follows
phone answer mode.
16
ENBLOCK
2LCD
OFF
When ON, 2 LINE LCD Keyset with navigation buttons
works as Enblock dialling mode. This option only works
when 2 LINE ENBLOCK option is set to ENABLE in
MMC 861.
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
SOME OPTIONS ARE DEPEND ON COUNTRY
ACTION
DISPLAY
1. Press Transfer button and enter 110.
Display shows:
[201] STN ON/OFF
2. Dial the option number from above list.(e.g., 4)
OR
Press Volume button to select the option and press
Right Soft button to move the cursor.
[201] STN ON/OFF
3. Press Volume button to select ON or OFF.
Press the Left or Right Soft button to return
to step 2.
OR
Dial 1 for ON or 0 for OFF.
[201] STN ON/OFF
AUTO HOLD
HOT KEYPAD
HOT KEYPAD
:OFF
:OFF
:ON
4. Press Transfer button and enter to exit.
RELATED ITEMS
MMC 301
MMC 701
2-22
ASSIGN STATION COS
ASSIGN COS CONTENTS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[111] PHONE RING TONE
Allows the system administrator or technician to select the ring tone heard at each phone.
There are eight ring tones available at each phone. A short tone burst of the selection will
be heard when the dial keypad is pressed.
CONDITIONS
NONE
DEFAULT DATA
FREQUENCY: 5
ACTION
DISPLAY
1. Press Transfer button and enter 111.
Display shows:
[201] RING TONE
2. Dial phone number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
OR
Press ANS/RLS button to select all.
[205] RING TONE
3. Dial 1~8 to select ring tone.
OR
Press Volume button to select ring tone and
press Right Soft button to move cursor.
[205] RING TONE
SELECTION
SELECTION
5
5
[ALL] RING TONE
SELECTION
SELECTION
?
5
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 114
© SAMSUNG Electronics Co., Ltd.
PHONE VOLUME
2-23
CHAPTER 2. MMC Programming
[112] ALARM REMINDER CLOCK
Allows the system administrator or technician to set or change the alarm clock/appointment
reminder feature for any station. This must be done for single line telephones, as they
cannot access programming. Three alarms may be set for each station and each alarm may
be defined as a one-time or TODAY alarm or as a DAILY alarm, as described below. The
TODAY alarm is automatically cancelled after it rings, while the DAILY alarm rings every
day at the same time. Alarm numbers are 1, 2 and 3. In the case of Secondary Pair
assignments(MMC 740) the alarm only rings the station that is programmed and does not
ring the paired station.
No
Type
Description
0
NOTSET
No alarm
1
TODAY
Alarm only once
2
DAILY
Alarm daily at set time
CONDITIONS
NONE
DEFAULT DATA
ALARMS ARE NOTSET
ACTION
2-24
DISPLAY
1. Press Transfer button and enter 112.
Display shows:
[201] ALM CLK(1)
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button.
[205] ALM CLK(1)
3. Dial 1~3 to select alarm.(e.g., 1)
OR
Press Volume button to select alarm and press
Right Soft button.
[205] ALM CLK(1)
4. Enter alarm time in 24-hour clock format.
(e.g., 1300 for 1 pm)
[205] ALM CLK(2)
HHMM: NOTSET
HHMM: NOTSET
HHMM: NOTSET
HHMM:1300 NOTSET
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
5. Dial entry from above list for alarm type.(e.g., 2)
OR
Press Volume button to select alarm type and
press Right Soft button to move cursor and return
to step 2.
[205] ALM CLK(2)
HHMM:1300 DAILY
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-25
CHAPTER 2. MMC Programming
[113] VIEW MEMO NUMBER
Allows a station user the ability to view a memo left by the user. A memo can be left by
entering it via the dial keypad using the table below. A memo of up to and including 13
characters can be entered.
CONDITIONS
NONE
INPUT CHARACTERS
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 113.
Display shows:
[201] VIEW MEMO
2. Press Right Soft button to move cursor and add
memo via dial keypad using procedure above.
[205] VIEW MEMO
1:
1:NEED BREAD
3. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-26
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[114] PHONE VOLUME
Allows the station user or system administrator to set the ring volume, off hook ring
volume, handset receive volume, speaker volume, background music volume and page
volume for any or all phones.
No
0
Type
RING VOLUME
Description
This is the volume setting for the phone ringer. There are eight volume
levels: level 1 is the lowest and level 8 the highest.
1
OFF-RING VOL
This is the volume of the alert tone that tells you there is a call camped
on to your phone. There are eight volume levels: level 1 is the lowest
and level 8 the highest.
2
HANDSET VOL
This is the volume setting for conversations on the handset receiver.
There are eight volume levels: level 1 is the lowest and level 8 the
highest.
3
SPEAKER VOL
This is the receive volume setting for conversations on the speaker
phone of a phone. There are 16 volume levels: level 1 is the lowest
and level 16 the highest.
4
BGM VOLUME
This is the volume you will hear background music over the phone
speaker at when your phone is idle and BGM is turned on. There are
16 volume levels: level 1 is the lowest and level 16 the highest.
5
PAGE VOLUME
This is the volume you will hear internal page over the phone speaker
when your phone is idle and BGM is turned on. There are 16 volume
levels: level 1 is the lowest and level 16 the highest.
CONDITIONS
NONE
DEFAULT DATA
RING VOLUME: 4
OFF-HOOK RING VOLUME: 4
HANDSET VOLUME: 4
SPEAKER VOLUME: 13
BGM VOLUME: 13
PAGE VOLUME: 13
© SAMSUNG Electronics Co., Ltd.
2-27
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 114.
Display shows:
[201] STN VOLUME
2. Dial phone number.(e.g., 205)
[205] STN VOLUME
RING VOLUME :4
RING VOLUME :4
3. Press Volume button to select volume type.
[205] STN VOLUME
SPEAKER VOL :13
4. Press Volume button to select volume.
[205] STN VOLUME
SPEAKER VOL :08
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 111
2-28
PHONE RING TONE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[115] SET PROGRAMMED MESSAGE
Allows the system administrator to set a programmed message at any or all phones. There
are 20 messages available.
CONDITIONS
The first ten are pre-programmed and the remaining entries can be customized in MMC
715, Programmed Station Message. The last five message are can be modified by each
phone user.
DEFAULT DATA
NO MESSAGES SELECTED
ACTION
DISPLAY
1. Press Transfer button and enter 115.
Display shows:
[201] PGMMSG(00)
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and
press Right Soft button to move cursor.
OR
Press ANS/RLS button to select all.
[205] PGMMSG(00)
3. Dial an entry number to select message number.
(e.g., 05)
OR
Press Volume button to select message and press
Right Soft button to return to step 2.
[205] PGMMSG(05)
CANCEL PGM MSG
CANCEL PGM MSG
[ALL] PGMMSG(??)
PAGE ME
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 715
MMC 722
MMC 723
© SAMSUNG Electronics Co., Ltd.
PROGRAMMED MESSAGE
STATION KEY PROGRAMMING
SYSTEM KEY PROGRAMMING
2-29
CHAPTER 2. MMC Programming
[116] ALARM AND MESSAGE
Allows the system administrator or technician to set or change the alarm clock/appointment
reminder feature for any station. This must be done for single line telephones because they
cannot access programming. Three alarms may be set for each station and each alarm may
be defined as a one-time or TODAY alarm or as a DAILY alarm, as described below.
The TODAY alarm is automatically cancelled after it rings, while the DAILY alarm rings
every day at the same time. It is also possible to set a message to display when the alarm is
sounded.
No
Type
Description
1
NOTSET
No alarm
2
TODAY
Alarm only once
3
DAILY
Alarm daily at set time
CONDITIONS
NONE
INPUT CHARACTERS
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
DEFAULT DATA
ALARMS ARE NOTSET
ACTION
2-30
DISPLAY
1. Press Transfer button and enter 116.
Display shows:
[201] ALM REM(1)
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
OR
Press ANS/RLS button to select all stations.
[205] ALM REM(1)
3. Dial 1~3 to select alarm.(e.g., 2)
OR
Press Volume button to select alarm and press
Right Soft button to move cursor.
[205] ALM REM(2)
HHMM: NOTSET
HHMM: NOTSET
[ALL] ALM REM(1)
HHMM: NOTSET
HHMM: NOTSET
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
4. Enter alarm time in 24-hour clock format.
(e.g., 1300 for 1pm)
Display will automatically advance to step 5.
[205] ALM REM(2)
5. Dial valid entry from above list for alarm type.
(e.g., 2)
OR
Press Volume button to select alarm type and
press Right Soft button to move cursor.
[205] ALM REM
6. Enter messages using above table and press
Right Soft button to return to step 2.
[205] ALM REM
HHMM:1300 NOTSET
HHMM:1300 DAILY
Sam SMITH
7. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-31
CHAPTER 2. MMC Programming
[117] EDIT TEXT MESSAGE
Allows the system administrator or technician to set or change text message for any station.
One station can use up to 10 text messages.
CONDITIONS
In MMC 611 Text Message Station set USED station only uses this feature. In case of a
large LCD phone, system set to USED automatically.
INPUT CHARACTERS
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
DEFAULT DATA
BLANK MESSAGE
ACTION
DISPLAY
1. Press Transfer button and enter 117.
Display shows:
[201] TXTMSG(01)
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
[205] TXTMSG(01)
3. Dial 01~10 to select message.
OR
Press Volume button to select message and
press Right Soft button to move cursor.
[205] TXTMSG(02)
4. Enter messages using above table and press
Right Soft button to return to step 3.
[205] TXTMSG(02)
Blank Message
Blank Message
Blank Message
SAME TIME
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 611
2-32
TEXT MESSAGE STATION
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[118] CONFERENCE GROUP
Allows the system administrator or technician to set one touch conference group using
GCONF key for any station. One station can use up to 5 conference groups, and each group
can be set 4 member except self station.
In MMC 612 Conference Group Station set USED station only uses this feature.
In case of a large LCD phone, system set to USED automatically.
On conference member, allows both internal station or station group number and outgoing
access code plus external telephone number.
CONDITIONS
In MMC 612 Conference Group Station set USED station only uses this feature.
In case of a large LCD phone, system set to USED automatically.
INPUT CONFERENCE GROUP NAME
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
Conference group names are written using the keypad. Each key press selects a character.
Pressing the dial pad key moves the cursor to the next position.
For example, if the group name is ‘SAMSUNG’, press the number ‘7 four times to get the
letter ‘S’. Now press the number ‘2 once to get the letter ‘A’. Continue selecting characters
from the table below to complete your message. Pressing the bottom left programmable
button will change the letter from upper case to lower case.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 118.
Display shows:
[201] GRP(1)NAME
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
[203] GRP(1)NAME
3. Dial 1~5 to select group.
OR
Press Volume button to select group and press
Right Soft button to move cursor.
[203] GRP(1)NAME
© SAMSUNG Electronics Co., Ltd.
2-33
CHAPTER 2. MMC Programming
4. Dial 0 to select name or dial 1~4 to select member.
OR
Press Volume button to select name or member
and press Right Soft button to move cursor.
OR
Press Left Soft button to return to step 3.
[203] GRP(1)MBR1
5. Enter conference member dial number and press
Right Soft button to return to step 4.
[203] GRP(1)MBR1
NONE
9-2794296
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 612
MMC 722
MMC 723
2-34
CONFERENCE GROUP STATION
STATION KEY PROGRAMMING
SYSTEM KEY PROGRAMMING
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[119] CALLER ID DISPLAY
Allows the technician to set the individual station display preference on a per station basis.
Caller ID or CLI can be selected to either show the name, number first, or no display
depending on the type of call. Caller ID or CLI displays have the following options:
No
Type
Description
0
NO DISPLAY
No Caller ID or CLIP data will be displayed.
1
NUMBER FIRST
The Caller ID or CLIP number received from the Central Office
will be displayed first.
2
NAME FIRST
The Caller ID or CLIP name received will be displayed first.
In the case of CLIP the number must be programmed in the
CLIP translation table(MMC 728). CLIP does not provide
names.
CONDITIONS
NONE
DEFAULT DATA
NUMBER FIRST
ACTION
DISPLAY
1. Press Transfer button and enter 119.
Display shows first station:
[201] CID DISP
2. Enter station number.(e.g., 205)
OR
Press Volume button to scroll through stations
and press Right Soft button to select a station.
OR
Press ANS/RLS button to select all and press
the Right Soft button.
[205] CID DISP
3. Dial display option 0, 1 or 2.(e.g., 2)
OR
Press Volume button to select option and press
Right or Left Soft button to return to step 2.
[205] CID DISP
NUMBER FIRST
NUMBER FIRST
[ALL] CID DISP
NUMBER FIRST
NAME FIRST
4. Press Transfer button and enter to exit.
OR
Press Speaker button to save and advance to next MMC.
© SAMSUNG Electronics Co., Ltd.
2-35
CHAPTER 2. MMC Programming
RELATED ITEMS
MMC 312
MMC 425
MMC 608
MMC 728
2-36
ALLOW CALLER ID
ASSIGN CID TRUNKS
ASSIGN REVIEW BLOCKS
CALLER ID TRANSLATION TABLE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[120] LARGE LCD OPTION
Allows the system administrator to set any of the large LCD phone for the following
options.
No
0
Option
IDLE DISPLAY
Description
Sets whether to display ‘CALNENDER’ or ‘INFORMATION’ on
LCD at idle state
1
DS KEY DISPLAY
Sets whether to display ‘Dial Number’ or ‘Directory Name’ for ‘DS’
key on LCD
2
DIAL MODE
Sets dial mode ENBLOCK or OVERLAP of phone
3
CONV DISP
Sets whether to display first SOFT menu screen or AOM menu
screen on LCD at conversation state
4
CALENDAR
Sets whether to display PREVIOUS screen or CALENDAR
screen on LCD at idle state
5
AOM CURSOR
Sets cursor position on AOM menu screen(01~99, PREV
POSITION)
CONDITIONS
NONE
DEFAULT DATA
IDLE DISPLAY: CALENDER
DS KEY DISPLAY: TEL NUMBER
DIAL MODE: ENBLOCK
ACTION
DISPLAY
1. Press Transfer button and enter 120.
Display shows:
[201] IDLE DISP
2. Enter station number.(e.g., 205)
OR
Press Volume button to scroll through stations
and press Right Soft button to select a station.
OR
Press ANS/RLS button to select ALL and press
the Right Soft button.
[203] IDLE DISP
3. Dial the option number from above list.(e.g., 4)
OR
Press Volume button to select the option and press
Right Soft button to move the cursor.
[203] DS KEY DSP
© SAMSUNG Electronics Co., Ltd.
CALENDER
CALENDER
[ALL] IDLE DISP
CALENDER
TEL NUMBER
2-37
CHAPTER 2. MMC Programming
4. Press Volume button to select ON or OFF.
Press the Left or Right Soft button to return to step 2.
OR
Dial 1 for ON or 0 for OFF.
[203] DS KEY DSP
EXT NAME
5. Press Transfer button and enter to exit.
RELATED ITEMS
MMC 719
2-38
IDLE DISPLAY
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[121] PHONE LANGUAGE
Allows phone users the ability to assign an LCD display based on user’s own language.
No
Language
00
ENGLISH
01
GERMAN
02
PORTUGAL
03
NORSK
04
DANISH
05
DUTCH
06
ITALY
07
SPANISH
08
SWEDISH
09
SPANISH/USA
10
FRENCH/CANADA
CONDITIONS
NONE
DEFAULT DATA
ENGLISH
ACTION
DISPLAY
1. Press Transfer button and enter 121.
Display shows:
[201] LANGUAGE
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and use
Right Soft button to move cursor.
OR
Press ANS/RLS button to select all stations.
[205] LANGUAGE
3. Dial 00~10 for language required.
OR
Press Volume button to make selection and
press Right Soft button.
[205] LANGUAGE
© SAMSUNG Electronics Co., Ltd.
ENGLISH
ENGLISH
[ALL] LANGUAGE
?
GERMAN
2-39
CHAPTER 2. MMC Programming
4. Press Transfer button and enter to save and exit.
OR
Press Speaker button to save and advance to
next MMC.
RELATED ITEMS
NONE
2-40
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[122] NEWS DISPLAY SPEED
Used to set the Smart news display speed. This timer is only related to the Smart News PC
Application Package.
CONDITIONS
NONE
DEFAULT DATA
03
ACTION
DISPLAY
1. Press Transfer button and enter 122.
Display shows first station:
[201] CALL SPEED
2. Enter station number.(e.g., 205)
OR
Press Volume button to scroll through stations
and press Right Soft button to select a station.
OR
Press ANS/RLS button to select all.
[205] CALL SPEED
3. Dial speed option.(03~10)
[205] CALL SPEED
03
03
03
04
4. Press Transfer button and enter to exit.
OR
Press Speaker button to save and advance to next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-41
CHAPTER 2. MMC Programming
[125] EXECUTIVE STATE
Allows the system administrator or technician to set executive station’s the following
options.
No
0
Option
EXEC STATE
Description
When inter-working with EASYSET, the state of executive station can
be displayed.
1
STATE(IN)
If EXEC STATE sets to OTHERS(IN), the EASYSET display this
message.
2
STATE(OUT)
If EXEC STATE sets to OTHERS(OUT), the EASYSET display this
message.
3
ANSWER MODE
When the secretary call by BOSS key, the executive station ringing or
automatically answer follows this option.
CONDITIONS
NONE
INPUT CHARACTERS
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
State display messages are written using the keypad. Each key press selects a character.
Pressing the dial pad key moves the cursor to the next position. For example, if the
message is ‘CONFERENCE’, press the number ‘2 three times to get the letter ‘C’.
Now press the number ‘6 three times to get the letter ‘O’. Continue selecting characters
from the table below to complete your message. Pressing the bottom left programmable
button will change the letter from upper case to lower case.
DEFAULT DATA
NONE
ACTION
2-42
DISPLAY
1. Press Transfer button and enter 125.
Display shows:
[201] EXEC STATE
2. Dial executive station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
[205] EXEC STATE
IN THE ROOM
IN THE ROOM
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
3. Dial 0~3 for selects option.
OR
Press Volume button to make selection and
press Right Soft button.
[205] EXEC STATE
4. Dial 0~9 for selects state.
OR
Press Volume button to make selection and
press Right Soft button.
[205] EXEC STATE
IN THE ROOM
IN A MEETING
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-43
CHAPTER 2. MMC Programming
[200] OPEN CUSTOMER PROGRAMMING
Used to open(enable) and close(disable) customer-level programming.
If programming is not opened and an attempt is made to access a system MMC,
the error message [NOT PERMIT] will be displayed. A four digits passcode is required to
access this MMC. Each digit can be 0-9. When opened, this MMC enables access to all
MMCs allowed in MMC 802 Customer Access MMC Number.
No
Mode
Description
0
DISABLE
Open(enable) customer-level programming
1
ENABLE
Close(disable) customer-level programming
CONDITIONS
NONE
DEFAULT DATA
DISABLE
ACTION
DISPLAY
1. Press Transfer button and enter 200.
Display shows:
ENABLE CUS.PROG.
2. Enter passcode.
ENABLE CUS.PROG.
PASSCODE:
PASSCODE:
Correct code shows:
ENABLE CUS.PROG.
DISABLE
Incorrect code shows:
ENABLE CUS.PROG.
PASSCODE ERROR
2-44
3. Press Volume button arrow key to select ENABLE
or DISABLE and press Right Soft button.
OR
Dial 1 for ENABLE or 0 for DISABLE.
ENABLE CUS.PROG.
4. Press Speaker button to advance MMC entry level
and press Volume button to select MMC.
OR
Enter MMC number and press Right Soft button
to enter MMC.
201:CUS.PASSCODE
ENABLE
SELECT PROG. ID
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
5. Press Transfer button to exit.
RELATED ITEMS
MMC 201
MMC 501
MMC 802
© SAMSUNG Electronics Co., Ltd.
CHANGE CUSTOMER PASSCODE
SYSTEM-WIDE TIMERS
CUSTOMER ACCESS MMC NUMBER
2-45
CHAPTER 2. MMC Programming
[201] CHANGE CUSTOMER PASSCODE
Used to change the passcode allowing access to MMC 200 Open Customer Programming
from its current value.
CONDITIONS
The passcode is four digits long. Each digit can be 0-9.
The current(old) passcode is required for this MMC.
DEFAULT DATA
PASSCODE: 1234
ACTION
DISPLAY
1. Press Transfer button and enter 201.
CUST. PASSCODE
NEW CODE:_
2. Enter new passcode via dial keypad.
(maximum four digits)
CUST. PASSCODE
3. Verify new passcode via dial keypad.
CUST. PASSCODE
NEW CODE:****
VERIFY
Passcode verified.(go to step 4)
OR
Passcode failure.
Return to step 2.
:****
CUST. PASSCODE
VERIFY
:SUCCESS
CUST. PASSCODE
VERIFY
:FAILURE
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 200
2-46
OPEN CUSTOMER PROGRAMMING
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[202] CHANGE FEATURE PASSCODE
Used to change the passcodes for the following features.
No
0
Feature
RING PLAN
Description
This is the passcode required to place the system in different ring
plans(RP) or change the ring time override(RTO).
1
DISA ALARM
This is the passcode required to clear a DISA ALARM generated when
the number of DISA attempts are exceeded.
2
ALARM CLR
This is the passcode required to clear a ALARM generated by the
disconnection of BI-PMS SIO.
-Available in Hotel/Motel enabled only.
3
AA RECORD
This is the passcode required to record prompts for use with the AA
ports on the Auto Attendant card.
4
DECT REGST
This is the passcode required to registration of DECT phone.
5
DELETE
This passcode is used to allow a change to be deleted from a room bill.
6
WLAN REGST
This is the passcode required to enter MMC 849.
CONDITIONS
The passcode is four digits long. Each digit can be 0-9.
The current passcode is required for this MMC.
DEFAULT DATA
RING PLAN: 0000
DISA ALARM: 5678
ALARM CLR: 8765
AA RECORD: 4321
DECT REGST: 4321
DELETE: 9999
WLAN REGST: 0000
© SAMSUNG Electronics Co., Ltd.
2-47
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 202.
Display shows:
CHANGE PASSCODE
2. Press Volume button to make selection Press
Right Soft button to move cursor to passcode entry.
CHANGE PASSCODE
3. Enter new passcode via digits from dial keypad.
CHANGE PASSCODE
Press Right Soft button to return to step 2.
Continue to change other passcodes.
RING PLAN :0000
AA RECORD :4321
AA RECORD :9999
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 410
MMC 507
MMC 722
MMC 849
2-48
ASSIGN DISA TRUNK
ASSIGN RING PLAN TIME
STATION KEY ASSIGNMENTS
WLAN CONFIGURATION
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[203] ASSIGN UA DEVICE
Assigns ringing device to be accessed when a Universal Answer(UA) key is pressed or the
UA pickup code is dialled. UA assignment is made in MMC 601 Assign Station Group for
a group and then the group is entered here. The device type is automatically determined by
the directory number(DN) entered.
Only one of the above options can be selected. If the ability to ring more than one
item(e.g., all four external page zones) is required, a station group containing all
four zone codes must be created.
Recipient
Description
NONE-NO UA
When there is no phone number
STATION
Station number
STN GROUP
Station group number
RING PAGE
External speaker phone number
COMMON BELL
Common bell phone number
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 203.
Display shows current assignment:
ASSIGN UA PORT
2. Dial DN of UA device.(e.g., 205)
OR
Use Volume buttons to scroll through
available devices.
ASSIGN UA PORT
NONE-NO UA
205 -STATION
3. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 204
MMC 601
MMC 605
© SAMSUNG Electronics Co., Ltd.
COMMON BELL CONTROL
ASSIGN STATION GROUP
ASSIGN EXTERNAL PAGE ZONE
2-49
CHAPTER 2. MMC Programming
[204] COMMON BELL CONTROL
Determines whether the common bell relay contacts have an interrupted or continuous
closure when activated. If interrupted is chosen, the relay follows an internal Trunk Line
ring pattern of one second closed followed by three seconds open.
CONDITIONS
When the common bell is not used for night time ring, the common bell must be set to
station group.
Common bell not set to night time ring should be set to station group so that all
stations of the group ring when one station rings.
DEFAULT DATA
CONTINUOUS
ACTION
DISPLAY
1. Press Transfer button and enter 204.
Display shows current setting:
[3801]COM. BELL
2. Dial common bell number.
OR
Press Volume button to make selection of
common bell numbers and press Right Soft button
to advance cursor.
[3801]COM. BELL
3. Dial 0 for continuous or 1 for interrupted operation.
[3802]COM. BELL
OR
Use Volume button to scroll through options and
press Right Soft button to return to step 2.
CONTINUOUS
CONTINUOUS
INTERRUPTED
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 203
MMC 601
2-50
ASSIGN UA DEVICE
ASSIGN STATION GROUP
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[205] ASSIGN LOUD BELL
Designates the station that controls the loud bell ring output of a MISC board. Each MISC
board can have up to a loud bell outputs.
CONDITIONS
The loud bell will follow the ring cadence of the designated station. Only a station can be
assigned to control the loud bell; a station group cannot be assigned.
DEFAULT DATA
UNASSIGNED
ACTION
DISPLAY
1. Press Transfer button and enter 205.
Display shows current setting:
[3901]LOUD BELL
2. Dial loud bell number.(e.g., 3902)
OR
Use Volume button to scroll through loud bell
numbers and press Right Soft button to move the
cursor.
[3902]LOUD BELL
3. Enter station number.(e.g., 201)
OR
Press Volume button to make selection and
press Right Soft button to return to step 2.
[3902]LOUD BELL
RING PAIR:NONE
RING PAIR:NONE
RING PAIR:201
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-51
CHAPTER 2. MMC Programming
[206] BARGE-IN TYPE
Sets the type of barge-in that is permitted.
No
0
Type
NO BARGE-IN
Description
Barge-in feature is unavailable regardless of a station’s barge-in
status.
1
2
BARGE-IN WITH
Barge-in will have an intrusion tone and display at the barged-in
TONE
on station.
BARGE-IN WITHOUT
Barge-in is allowed. There is no barge-in tone or display at the
TONE
barged-in on station and the barging-in station will be muted.
CONDITIONS
NONE
DEFAULT DATA
NO BARGE-IN
ACTION
DISPLAY
1. Press Transfer button and enter 206.
Display shows:
BARGE IN TYPE
2. Dial 0 2 to select barge-in type.(e.g., 2)
OR
Press Volume button to select barge-in type and
press Right Soft button.
BARGE IN TYPE
NO BARGE IN
WITHOUT TONE
3. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 301
MMC 701
2-52
ASSIGN STATION COS
ASSIGN COS CONTENTS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[207] ASSIGN VM/AA PORT
Enables SLI ports to be designated as NORMAL or VMAA. VMAA ports receive digits
designated in MMC 726 VM/AA Options and also receive a true disconnect signal upon
completion of a call. Only SLI cards, not key daughter boards, support disconnect signal.
Do not make VMAA ports data; this will return them to a single line port and stop voice
mail integration. VMAA ports have the equivalent of data protect written in the program
and are protected against tones.
This MMC is not used to assign voice mail card ports. Voice mail card ports are
assigned as voice mail ports automatically when the system detects a CADENCE
or a SVMi-8/16 card.
CONDITIONS
NONE
DEFAULT DATA
NORMAL PORT
ACTION
DISPLAY
1. Press Transfer button and enter 207.
[209] VMAA PORT
NORMAL PORT
Display shows:
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
[205] VMAA PORT
3. Dial 1 or 0 to select port type.
(1: VMAA, 0: NORMAL)
Press Volume button to select option and press
Right Soft button.
[205] VMAA PORT
NORMAL PORT
VMAA PORT
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 726
MMC 601
© SAMSUNG Electronics Co., Ltd.
VM/AA OPTIONS
STATION GROUP
2-53
CHAPTER 2. MMC Programming
[208] ASSIGN RING TYPE
Provides the flexibility to program single lines to have ICM ringing, Trunk Line ringing
and data secure. With the many types of external ringing devices, all configurations can be
met. All devices will also have a positive disconnect signal. Do not make VM/AA ports
data; this will return them to a single line port and stop voice mail integration.
No
Type
Description
0
ICM RING
Follows normal SLI ring cadence.
1
CO RING
Follows Trunk line ring cadence.
2
DATA RING
Follows Trunk line ring cadence and not supports off hook ring.
CONDITIONS
NONE
DEFAULT DATA
ICM RING
ACTION
DISPLAY
1. Press Transfer button and enter 208.
Display shows:
[209] RING TYPE
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
[205] RING TYPE
3. Dial 1,2 or 0 to select port type.(e.g., 2)
OR
Press Volume button to select option and press
Left or Right Soft button to return to step 2 above.
[205] RING TYPE
ICM RING
ICM RING
DATA RING
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-54
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[209] ASSIGN ADD-ON MODULE
Designates to which phone an add-on module(AOM) is assigned.
There is no limit to the number of AOMs that can be assigned in the system. The maximum
number of AOMs that can be assigned to a keyset is 4.
No
OHVAED Status
Description
0
OHVAED OFF
Off-hook announcement is not played to the add-on-module
1
OHVAED ON
Off-hook announcement is played to the add-on-module
CONDITIONS
AOM cannot be designated as master. If no AOM exists in a tenant, the ‘AOM NOT
EXIST’ message is displayed.
DEFAULT DATA
NONE FOR MASTER
ACTION
DISPLAY
1. Press Transfer button and enter 209.
Display shows first AOM:
[301] AOM MASTER
2. Dial AOM number.
OR
Use Volume button to scroll through AOM numbers
and use Soft buttons to move cursor.
[301] AOM MASTER
3. Enter station number.(e.g., 301)
OR
Use VOLUME for selection of stations and
press Right Soft button to return to step 2.
[301] AOM MASTER
MASTER:NONE
MASTER:NONE
MASTER:201
4. Press Transfer button and enter to exit.
OR
Press Speaker button to save and advance to next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-55
CHAPTER 2. MMC Programming
[210] CUSTOMER ON/OFF PER TENANT
Allows the system administrator to set in system features on a per-tenant basis.
Each system option has a corresponding dialling number, as listed below. All options toggle
ON/OFF.
No
00
Option
DISA PSWD
Default
ON
Description
When ON, a caller must enter extension number and DISA
password when they call a DISA trunk. When OFF, extension
number and DISA password are not required and the caller
has full access to all features allowed on this trunk.
01
LCR ENABLE
OFF
This option determines whether the system will or will not
route outgoing calls based on the information in the LCR
routing tables
03
PERI UCD RPT
OFF
Periodic UCD Information provider. Enables UCD Statistics
data on a per UCD group basis to print out on the IO port
which has been set as PERI UCD in real time(every 3~99
seconds). This allows the information to be interfaced and
manipulated by an external package or third party provided
software.
04
CID CODE INS
OFF
When ON, the system will insert the country code when
receiving CID information. This feature can use the CID
display call back feature.
05
DISA MOH
OFF
When ON, outside parties will hear trunk MOH instead of dial
tone from the time the system answers a DISA trunk until the
caller dials a digit.
06
TRANSFER
OFF
MOH
When ON, outside parties will hear trunk MOH instead of
ring back tone from the time a transfer is completed until the
call is answered by an internal party.
08
DID BSY ROUT
OFF
When ON, a DID call directed to a busy station will re-route
to to the destination in MMC 406 for that trunk if CW is set to
OFF in MMC 714. If the CW option is set to ON the call will
camp on. When OFF and the CW option is set to OFF, the
call will
re-route to the operator.
09
ALARM MOH
ON
When ON, if station user answer alarm ring, will hear station
MOH instead of dial tone.
12
CONF TONE
OFF
When ON, provides conference tone every conference tone
time.
-Available in Australia or Italy only
13
RECALL PIKUP
ON
When ON, a call recalling to a station can be picked up using
Direct Call Pickup, Pickup Group and My Group features.
This applies to held calls recalling and transferred calls
recalling to a station.
2-56
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
No
14
Option
ICM EXT FWD
Default
OFF
Description
When ON, call forward external is allowed when intercom calls
are placed to a station that has Call Forward External
programmed and set.
16
DID ERR TONE
OFF
This option was added to provide error tone when an invalid
DID number is received.
18
KTS DISC ALM
OFF
When ON, generates system alarm when a phone
disconnect or connect.
19
OFF HOOK ALM
OFF
When ON, generates system alarm when a phone maintains
off hook condition longer than timer.
20
SL SELF RING
OFF
When ON, generates ring during 10 seconds when a single
line phone dials self number and hang up.
21
SGR INC BUSY
OFF
When ON, generates busy tone when all station group
member busy for group call. This setting does not work for
Station Groups which have Unconditional Ring Mode.
24
TRANSFER
OFF
CANCEL
When OFF, a single line phone will be able to handle 2 calls
simultaneously. Using the hook-flash to toggle between
them. When ON, a single line telephone will be able to
connect to the second call, but pressing the hook flash will
not toggle between the two calls it will disconnect the second
call and reconnect the single line telephone to the first call.
26
RECALL DISC
OFF
When ON, the system disconnects a call when transfer
recall.
29
ARD TONE CHK
ON
When OFF, the system use time for checking destination is
busy when auto retry.
30
VPN ENABLE
OFF
31
IN TOLL CHK
OFF
When ON, the Australia type VPN enabled.
When OFF, the system doesn’t toll restrict when incoming
call.
32
ISDN
OFF
PROGCON
When ON, if an outgoing call receives PROGRESS
message from ISDN trunk, the call will connect without
CONNECT message.
33
INCLUDE VAT
OFF
When OFF, not printed VAT total line when Hotel
Report.(Available in Hotel/Motel enabled only)
36
DSS KEY DPU
OFF
When ON, directed pick-up the call when press ringing DS
key.
37
BEGN DGT DSP
OFF
When ON, an outside call is made via speed dial or LNR
where more than 11 digits are dialled then the first dialled
digits are shown on the phone display.
38
ONE TCH
OFF
FACC
39
SGR ALL OUT
When OFF, the forced account mode user can not use one
touch account code(ACC) key.
OFF
When ON, the last of station group member can out of
group.
© SAMSUNG Electronics Co., Ltd.
2-57
CHAPTER 2. MMC Programming
No
2-58
Option
Default
Description
40
CHAIN FWD
ON
When ON, a call is directed to a station that may be
forwarded to another station that is call forwarded to a
VMAA, then the caller will be directed to the last station’s
mailbox it reached. When OFF, the caller will be directed to
the first station’s mailbox instead of the last.
41
TRK MONITOR
OFF
When ON, can override to trunk and a call is connected
override extension when a original caller hang on. When
OFF, can override to extension only and a call is
disconnected when a original caller hang on.
42
VOIP MFRALOC
OFF
When ON, a MFR assigned for VoIP tandem call when a call
incoming from VoIP trunk to another trunk outgoing.
43
NTWK
AUTOTMR
OFF
When OFF, a call duration timer disabled via networking
intercom call.
44
USE EURO
OFF
When ON, a call cost display by euro currency.
45
NO STAFF
COD
OFF
When ON, the steps verifying the staff code will be omitted
in HOTEL operation.
46
PERI UCD SIO
OFF
When ON, the PERI UCD data will be sent to the SMDR IO
port.
47
AUTO
CLEANED
OFF
When the room is checked-out, the room status is changed
to NEED CLEAN. When the option is set to ON, the room
status will be changed to AVAILABLE.
48
REDIAL REVW
OFF
When ON, the CALL LOG review status will be appeared
when LNR button is pressed.
49
ISDN KEYFAC
OFF
When ON, if phone user press ‘*’ or ’#’ during conversation
via BRI trunk, system send information message instead of
digit message.
50
CHK SPV TRK
OFF
When ON, if both trunks don’t have supervision feature then
cannot make outgoing transfer or unsupervised conference.
51
PRE FWD
BUSY
OFF
When ON, a call arrives busy station, that is not set forward
busy, if preset no answer destination is available, a call reroute to that destination immediately.
52
ORG DIAL LOG
OFF
When ON, originally dialled digit will be saved as outgoing
call log in Large LCD Phone. When OFF, invalid dialling
such as dialling of not exist station number will not be saved
as outgoing call log in Large LCD Phone.
53
TIE TRSF RCL
ON
When ON, the trunk call is transferred to the TIE line and is
not answered within transfer recall time, the call is recalled
to the original transferring station.
54
VOIP REALRBT
OFF
When ON, the system will connect real path of outgoing
trunk to the incoming VOIP Trunk user instead of providing
the virtual ringback tone.
55
SMDR
AUT2ACC
OFF
When ON, the AUTORIZATION CODE will be printed in
ACCOUNT field of SMDR.
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
SOME OPTIONS ARE DEPEND ON COUNTRY
ACTION
DISPLAY
1. Press Transfer button and enter 210.
Display shows:
TEN. ON AND OFF
2. Dial option number.(e.g., 00)
Press Right Soft button to move cursor.
TEN. ON AND OFF
3. Dial 1 for ON or 0 for OFF.
OR
Press Volume button to make selection and
press Right Soft button.
TEN. ON AND OFF
DISA PSWD
DISA PSWD
DISA PSWD
:OFF
:OFF
:ON
4. Repeat steps 2-3 for other options.
OR
Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 410
ASSIGN DISA TRUNK
LCR PROGRAMMING
MMC 710
MMC 711
MMC 712
MMC 713
LCR DIGIT TABLE
LCR TIME TABLE
LCR ROUTE TABLE
LCR MODIFY DIGIT TABLE
MOH PROGRAMMING
MMC 308
MMC 309
MMC 736
MMC 756
© SAMSUNG Electronics Co., Ltd.
ASSIGN BACKGROUND MUSIC SOURCE
ASSIGN STATION MOH SOURCE
ASSIGN AA MOH
ASSIGN VM MOH
2-59
CHAPTER 2. MMC Programming
CID PROGRAMMING
MMC 119
MMC 312
MMC 425
MMC 608
MMC 728
CALLER ID DISPLAY
ALLOW CALLER ID
ASSIGN CID TRUNKS
ASSIGN REVIEW BLOCKS
CALLER ID TRANSLATION TABLE
DID PROGRAMMING
MMC 416
MMC 714
ASSIGN E & M/DID RINGDOWN
DID NUMBER AND NAME TRANSLATION
VM/AA PROGRAMMING
MMC 207
MMC 726
MMC 601
ASSIGN VM/AA PORT
VM/AA OPTIONS
ASSIGN STATION GROUP
ALARM PROGRAMMING
MMC 112
MMC 116
2-60
ALARM REMINDER CLOCK
ALARM AND MESSAGE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[211] DOOR RING ASSIGNMENT
Designates which station or group of stations will ring when a door box button is pressed.
If the ring plan destinations are not input the default ring plan 1 is used. Available Ring
Plan inputs are 1 through 6.
CONDITIONS
NONE
DEFAULT DATA
STATION GROUP: 500
ACTION
DISPLAY
1. Press Transfer button and enter 211.
Display shows first door phone:
[229] DOOR RING
2. Dial door phone number.(e.g., 230)
OR
Press Volume button to scroll through door phone
numbers and use Right Soft button to move cursor.
OR
Press ANS/RLS button to select All door ring.
[230] DOOR RING
3. Enter new ring plan number selection via dial
keypad.
OR
Press Volume button to make selection and
press Right Soft button.
[250] DOOR RING
1:500
1:500
2:500
2:500
ALL] DOOR RING
1:500
1:301
2:500
2:500
4. Press Right Soft button to return to step 2.
OR
Press Left Soft button to return to step 3.
OR
Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-61
CHAPTER 2. MMC Programming
[214] DISA ALARM RINGING STATION
Assigns the DISA alarm to ring at a specific phone. It is recommended that the person who
can clear the alarm also receives the notification.
CONDITIONS
A valid destination can be either a station group or an individual station.
The alarm ringing station or group will follow the ring plan time destination.
DEFAULT DATA
ALL RING PLAN: 500
ACTION
DISPLAY
1. Press Transfer button and enter 214.
Display shows:
DISA ALARM RING
2. Enter in valid destination number for ring plan.
(e.g., 217)
OR
Press Volume button to make selection and
press Right Soft button to advance cursor.
DISA ALARM RING
3. Enter in valid destination number for another
ring plan.(e.g., 249)
OR
Press Volume button to make selection.
DISA ALARM RING
1:500
1:217
1:217
2:500
2:500
2:249
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 202
MMC 410
2-62
CHANGE FEATURE PASSCODES
ASSIGN DISA TRUNK
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[215] VOICE DIALLER OPTIONS
Assigns either two(2) channels and seven(7) users or one(1) channel and five(5) users to
the VDIAL card. When changing channel size, you will be prompted to ‘clear RAM’. This
is only for Voice Dialler, not the system.
This will prevent accidental usage of pre-recorded names. It is advised that you clear RAM
before assigning users in MMC 216.
No
0
Voice Dial Option
2CH-7USER-20BIN
Description
Two ports can be used for a voice dial device card. A port can
accommodate up to 7 subscribers and up to 20 names per
subscriber.
1
1CH-5USER-40BIN
One port can be used for a voice dial device card. A port can
accommodate up to 5 subscribers and up to 40 names per
subscriber.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 215.
Display shows:
[3551]VDIAL OPTN
2. Enter Voice Dialler number(e.g., 3551)
via dial keypad.
OR
Press Volume button to select Voice Dialler and
use Right Soft button to move cursor.
[3551]VDIAL OPTN
3. Dial 0 or 1 for Voice Dialler channel select.
OR
Press Volume button to make selection and
press Right Soft button.
[3551]VDIAL OPTN
2CH-7USER-20BIN
2CH-7USER-20BIN
1CH-5USER-40BIN
4. Press Transfer button and enter to save and exit.
OR
Press Speaker button to save and advance to next MMC.
© SAMSUNG Electronics Co., Ltd.
2-63
CHAPTER 2. MMC Programming
RELATED ITEMS
MMC 216
MMC 722
MMC 723
MMC 724
2-64
VOICE DIALLER ASSIGNMENTS
STATION KEY PROGRAMMING
SYSTEM KEY PROGRAMMING
DIAL NUMBER PLAN
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[216] VOICE DIALLER ASSIGNMENTS
Allows a station to be assigned to a channel of the VDIAL, card, to dial a personal speed
dial number. The number of users assigned to this feature is controlled by MMC215,
VOICE DIALLER OPTIONS, which allows either two(2) channels with seven(7) users or
one(1) channel with five(5) users.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 216.
Display shows:
[3551]VDIAL DIAL
2. Enter Voice Dialler number(e.g., 3551) via dial
keypad.
OR
Press Volume button to select Voice Dialler and
use Right Soft button to move cursor.
[3551]VDIAL DIAL
3. Dial 1-7 for user index number.
OR
Press Volume button to make selection and press
Right Soft button.
[3551]VDIAL DIAL
4. Dial extension number.
OR
Press Volume button to make selection and press
Right Soft button to return to step 3.
[3551]VDIAL DIAL
USER 1:NONE
USER 1:NONE
USER 1:NONE
USER 1:201
5. Press Transfer button and enter to save and exit.
OR
Press Speaker button to save and advance to next
MMC.
RELATED ITEMS
MMC 215
MMC 722
MMC 723
MMC 724
© SAMSUNG Electronics Co., Ltd.
VOICE DIALLER OPTIONS
STATION KEY PROGRAMMING
SYSTEM KEY PROGRAMMING
DIAL NUMBER PLAN
2-65
CHAPTER 2. MMC Programming
[217] TRAFFIC REPORT OPTION
This MMC is used to print a traffic report and select options. The traffic report can be
printed upon demand, every hour, at a programmed time of each day, or up to three
separate timed shifts. Automatic printing will always clear the totals.
When report MANUAL PRINT OUT is selected, the options are:
No
Option
0
PRINT AND CLEAR
A report is printed and all totals are reset to 0.
1
PRINTOUT ONLY
A report is printed and all the totals are saved.
CANCEL
The program return to previous menu if no report is ended.
2
Description
PRINTOUT
When AUTO PRINT OPTN is selected, the options are:
No
Option
Description
0
AUTO PRINT OFF
Automatic print feature is disabled.
1
DAILY
A report is printed at a programmable time every day and all the
totals are reset to ‘0 .
2
EVERY HOUR
A Traffic report will be printed every hour.
3
TIME SHIFTS
Up to three separate Start and End times may be programmed to
report traffic within certain times of a day. A report is printed at the
end of each End time and all totals are reset to ‘0 .
When a report is printed, the totals represent call statistics accumulated from the date of the
last report stated as BEGINNING: D & T up to the date of this printout stated as ENDING
D & T.
If there are no trunks in a group, the trunk group report for that group will not print.
CONDITIONS
NONE
DEFAULT DATA
NO REPORT
2-66
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
ACTION
DISPLAY
1. Press Transfer button and enter 217.
Display shows:
TRAFFIC REPORT
2. Dial 0 for demand or 1 for automatic print.
OR
Press Volume button to select and press Right
Soft button.
TRAFFIC REPORT
3. Dial 0, 1, 2 or 3 for automatic print option.
OR
Press Volume button to select option and press
Right Soft button.
TRAFFIC REPORT
4. Enter daily report time.(HHMM)
TRAFFIC REPORT
MANUAL PRINTOUT
AUTO PRINT OPTN
DAILY
DAILY
HHMM:2359
HHMM:2200
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 804
© SAMSUNG Electronics Co., Ltd.
SYSTEM I/0
2-67
CHAPTER 2. MMC Programming
[220] ISDN SERVICE TYPE
Assign the ISDN service type of single line telephone port. Service consist of BC(Bearer
Capability) and HLC(High Layer Capability).
No
Type
Description
BC
HLC
0
VOICE
Voice service
Speech
1
FAX 3
G3 FAX service
3.1 kHz Audio
FAX G2/G3
2
AUDIO 3.1
3.1 kHz Audio service
3.1 kHz Audio
None
3
MODEM
MODEM service
3.1 kHz Audio
Telephony
DEFAULT DATA
VOICE
ACTION
DISPLAY
1. Press Transfer button and enter 220.
Display shows:
[209] ISDN SVC
2. Enter the station number.(e.g., 210)
OR
Press Volume button to select station and press
Right Soft button.
[210] ISDN SVC
3. Select service type.(0-3)
OR
Press Volume button to select option and press
Right Soft button.
[210] ISDN SVC
VOICE
VOICE
AUDIO 3.1
4. Press Transfer button and enter button to exit.
OR
Press Speaker button to advance next MMC.
CONDITIONS
NONE
RELATED ITEMS
NONE
2-68
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[221] EXTENSION TYPE
This MMC enables station ports to be defined for a specific use. Each telephone can be
designated as being one of the five(5) following types. These types can be changed by
dialling the type number or by scrolling through the types and pressing Right Soft button to
select the type desired.
No
0
Type
NORMAL STATION
Description
This is the default setting. The station will operate in the normal
manner associated with this type of station. Ports designated as
VMAA in MMC 207 must be designated as normal in this MMC.
1
GUEST SMOKING
When a station is designated as this type it will appear in room
status and check in features as a smoking room.
2
GUEST NO SMOKING
When a station is designated as this type it will appear in room
status and check in features as a non smoking room.
3
MEETING ROOM
Stations designated as Meeting room stations will have the same
attributes as guest rooms with regard to cleaning and occupied
status but will not show up while scrolling through room status
lists.
4
ADMINISTRATOR
Only stations designated as administrator stations can use the
hotel motel features such as check in etc.
5
FAX STATION
When a station is designated as this type it can be assigned to
pair station of GUEST SMOKING ROOM or GUEST NO
SMOKING ROOM in MMC 223.
CONDITIONS
This function can be used only when the hotel function is enabled at ‘MMC 813 HOTEL
OPERATION’.
DEFAULT DATA
NORMAL STATION
© SAMSUNG Electronics Co., Ltd.
2-69
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 221.
Display shows:
[201] PHONE USE
2. Dial station number.(e.g., 214)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
[214] PHONE USE
3. Dial 0 to 5 to select station type.
OR
Press Volume button to select option and press
Right Soft button.
[214] PHONE USE
NORMAL STATION
NORMAL STATION
GUEST NO SMOKING
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-70
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[222] FAX PAIR
This MMC enables a guest room to have a additional FAX line.
CONDITIONS
This function can be used only when the hotel function is enabled at ‘MMC 813 HOTEL
OPERATION’.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 222.
Display shows:
[201] FAX PAIR
2. Enter the room station number via dial keypad.
(e.g., 202)
OR
Press Volume button to select and press Right
Soft button.
[202] FAX PAIR
3. Enter the fax station number via dial keypad.
(e.g., 2902)
OR
Press Volume button to select and press Right
Soft button.
[202] FAX PAIR
NONE
NONE
290
4. Press Transfer button and enter button to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 222
MMC 813
© SAMSUNG Electronics Co., Ltd.
EXTENSION TYPE
HOTEL OPERATION
2-71
CHAPTER 2. MMC Programming
[224] WAKE-UP ANNOUNCEMENT
This MMC is enhance Wake Up feature. The system will play a recorded message when a
Wake Up call is answered by the user. The Wake Up Announcement feature will require an
Automated Attendant(AA) card be installed in the system. When a Wake Up call is
answered, the system will access the customized Wake Up message(1-48) that has been
recorded in the AA card. The end user will record this message and have the ability to
change it when desired Auto Attendant operation. The Wake Up message will have no
default ROM message assigned to it. However a ROM message(49-64) may also be
assigned as the Wake Up message if desired.
This MMC has three options.
No
0
Option
AA GROUP
Description
Determines which AA group will be connected when a Wake Up
call is answered. This destination can be a any AA groups.
1
MESSAGE NO
Determines which message will be played when a Wake Up call is
answered. This destination can be a custom recorded message(148) or one of the pre-programmed messages(49-64).
2
GROUP BUSY
Determines which tone source will be connected when a AA group
members are all busy. This destination can be a NONE, TONE or
extern music on hold.
If NONE set then dial tone connected, if TONE set then hold tone
connected.
CONDITIONS
NONE
DEFAULT DATA
AA GROUP: NONE
MESSAGE NO: NONE
GROUP BUSY: NONE
2-72
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
ACTION
DISPLAY
1. Press Transfer button and enter 224.
Display shows:
WAKE-UP ANNOUNCE
2. Dial 0, 1 or 2 for option select.
OR
Press Volume button to select option and press
Right Soft button.
WAKE-UP ANNOUNCE
3. Enter the AA group number.
OR
Press Volume button to select and press Right
Soft button to return to step 2.
4. Press Transfer button and enter button to exit.
OR
Press Speaker button to advance next MMC.
WAKE-UP ANNOUNCE
AA GROUP
AA GROUP
AA GROUP
:NONE
:NONE
:520
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-73
CHAPTER 2. MMC Programming
[300] CUSTOMER ON/OFF PER STATION
Allows the following features to be enabled on a per-station basis.
No
00
Option
ACCESS DIAL
Default
ON
Description
Determines whether a user can select a trunk or trunk
group by dialling its directory number(DN). This
selection should be turned to off when using LCR.
01
MICROPHONE
ON
Allows all 12 and 24 button phones to be used in the
speakerphone mode.
02
OFF-HOOK RING
ON
Will allow a short burst of ring tone to indicate another call.
03
SMDR PRINT
ON
When the station is set for no Trunk Line calls to and
from this station, the station will not print on SMDR.
This includes transferred calls or calls picked up from
hold or park.
04
TGR ADV.TONE
ON
When this feature is set to ON, a warning tone will be
heard each time LCR advances to the next route.
05
VMAA FORWARD
ON
This feature selects whether Trunk Line calls can be
forwarded to voice mail. When ON, Permits forward to
voice mail. When OFF, No forward to voice mail.
07
NGT PASSCODE
ON
When ON, the steps verifying the RING PLAN
passcode will be added in Ring Plan change.
08
INTRCOM SMDR
OFF
When the station is set to OFF, the station will not print
intercom calls on SMDR.
09
FWD DLY USE
OFF
When the station is set to ON, if the station has no
answer forward number without no answer forward set
then a call both ringing original extension and no
answer forward number when a incoming call is
directed to the station and the station does not answer
until no answer forward time.
10
FORWARD OVRD
OFF
When the station is set to ON, if the station call to
forwarded station, the call will not forward.
11
RECL TO OPER
OFF
When the station is set to ON, if the station transfer a
call and the destination doesn’t answer, the call will be
recall to operator instead of the station.
12
SLT LP OPEN
OFF
When the normal phone is set to ON, if the station
receives real disconnect signal instead of busy tone or
error tone. In case of VMAA ports or DATA RING ports
are not reference this option, this type SLI ports are
always receives real disconnect signal.
13
CID PHONE
OFF
When RCM2 card is installed and this option is set to
ON, the system will provide the CID signal to the SLT.
2-74
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
SOME OPTIONS ARE DEPEND ON COUNTRY
ACTION
DISPLAY
1. Press Transfer button and enter 300.
Display shows:
[201] CUS.ON/OFF
2. Dial station number.(e.g., 205)
OR
[205] CUS.ON/OFF
Press Volume button to select station.
OR
Press ANS/RLS button for all and press
Right Soft button to move cursor.
ACCESS DIAL :ON
ACCESS DIAL :ON
[ALL] CUS.ON/OFF
ACCESS DIAL :ON
3. Press Volume button to select feature and
press Right Soft button to move cursor.
[ALL] CUS.ON/OFF
4. Dial 1 for ON or 0 for OFF.
OR
Press Volume button to select and press
Right Soft button.
[ALL] CUS.ON/OFF
ACCESS DIAL :ON
ACCESS DIAL :OFF
5. Press Left Soft button to return to step 2.
Press Right Soft button to return to step 1.
OR
Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
LCR PROGRAMMING
MMC 710 LCR DIGIT TABLE
MMC 711 LCR TIME TABLE
MMC 712 LCR ROUTE TABLE
MMC 713 LCR MODIFY DIGIT TABLE
© SAMSUNG Electronics Co., Ltd.
2-75
CHAPTER 2. MMC Programming
[301] ASSIGN STATION COS
Used to assign class of service to each phone. There are 30 different classes of service that
are defined in MMC 701, Assign COS Contents. There are 6 ring plans based on the Ring
Plan Time in MMC 507 that can apply to the COS. Classes of service are numbered 01-30.
Default is COS 01.
CONDITIONS
NONE
DEFAULT DATA
RING PLANS 1-6: 01
ACTION
2-76
DISPLAY
1. Press Transfer button and enter 301.
Display shows first station:
[201] STN COS
2. Dial station number.(e.g., 205)
OR
Use Volume button to scroll through stations
Press Right Soft button to advance step 3.
OR
Use Volume button to scroll through stations and
press Left Soft button to advance step 4.
OR
Press ANS/RLS button to select all stations.
[205] STN COS
3. Enter new ring plan selection via dial keypad.
OR
Press Volume button to make selection OR
press Right Soft button to move cursor.
[205] STN COS
4. Enter ring plan class of service.(e.g., 05)
OR
Use Volume button to scroll through classes of
service and press Right Soft button to advance
the next ring plan.
OR
Use Volume button to scroll through classes of
service and press Left Soft button to return to step 2.
[205] STN COS
1:01
1:01
2:01
2:01
3:01
3:01
[ALL] STN COS
1:01
1:01
1:05
2:01
2:01
2:01
3:01
3:01
3:01
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
5. Enter the next ring plan class of service.(e.g., 05)
OR
Use Volume button to scroll through classes of
service and press Right Soft button to move cursor
to the next ring plan.
OR
Use Volume button to scroll through classes of
service and press Left Soft button to return to
previous step.
[205] STN COS
1:05
2:01
3:01
6. Press Transfer button and enter to save and exit.
OR
Press Speaker button to save and advance to next
MMC.
RELATED ITEMS
MMC 701
MMC 507
MMC 740
© SAMSUNG Electronics Co., Ltd.
ASSIGN COS CONTENTS
ASSIGN RING PLAN TIME
SECONDARY STATION
2-77
CHAPTER 2. MMC Programming
[302] PICKUP GROUPS
Allows the assignment of stations into call pickup groups. There is a maximum of 99
pickup groups. An unlimited number of members can belong to each group. Stations can
only be in one pickup group at any given time.
CONDITIONS
NONE
DEFAULT DATA
NO PICKUP GROUPS ASSIGNED
ACTION
DISPLAY
1. Press Transfer button and enter 302.
Display shows:
[201] PICKUP GRP
2. Dial station number.(e.g., 205)
OR
Use Volume button to select station number and
press Right Soft button.
OR
Press ANS/RLS button to select all.
[205] PICKUP GRP
3. Dial pickup group number.(e.g., 05)
OR
Press Volume button to select group number.
[205] PICKUP GRP
PICKUP GRP:NONE
PICKUP GRP:NONE
[ALL] PICKUP GRP
PICKUP GRP:??
PICKUP GRP:05
4. Press Right Soft button to return to step 2 to
enter more stations.
OR
Press Left Soft button to return to step 3.
OR
Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 107
MMC 722
MMC 723
2-78
KEY EXTENDER
STATION KEY PROGRAMMING
SYSTEM KEY PROGRAMMING
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[303] ASSIGN BOSS/SECRETARY
Assigns BOSS phones to SECRETARY phones. One BOSS station can have up to and
including four SECRETARY stations and one SECRETARY station can have up to and
including four BOSS stations.
CONDITIONS
A dedicated BOSS button must be programmed on the SECRETARY phone(s).
A dedicated BOSS button must also be programmed on the BOSS phone.
A station designated as BOSS may not be assigned as a secretary of another boss.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 303.
Display shows:
BOSS STN:NONE
2. Dial BOSS station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button.
BOSS STN:205
3. Dial SECRETARY number.(1, 2, 3 or 4)
OR
Press Volume button to select number and press
Right Soft button.
BOSS STN:205
4. Dial SECRETARY station number.(e.g., 201)
OR
Press Volume button to select station.
Press Right Soft button to return to step 3 to
enter more SECR numbers.
BOSS STN:205
SECR 1:NONE
SECR 1:NONE
SECR 1:NONE
SECR 1:201
BOSS STN:205
SECR 2:202
5. Press Left Soft button to return to step 2 and
continue entries.
OR
Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 722
© SAMSUNG Electronics Co., Ltd.
STATION KEY PROGRAMMING
2-79
CHAPTER 2. MMC Programming
[304] ASSIGN EXTENSION/TRUNK USE
Allows trunk use groups on a per-station use group basis the ability to answer incoming
calls, to dial out or to do both.
CONDITIONS
Stations are set within the use group number 001~300 and trunks are within the use
group number 301~500 at ‘MMC 614. ASSIGN USE GROUP’.
If a station is set to NO Dial, the station will not have the ability to place a call.
If the station is set to NO Answer, the station cannot answer an incoming call.
DEFAULT DATA
DIAL: YES
ANS: YES
ACTION
2-80
DISPLAY
1. Press Transfer button and enter 304.
Display shows:
(001) USE (301)
2. Dial the station use group number.(e.g., 005)
OR
Press Volume button to select station use group
and press Right Soft button.
OR
Press ANS/RLS button to select all station use
Group.
(005) USE (301)
3. Dial the station use group number.(e.g., 304)
OR
Press Volume button to select trunk use group
and press Right Soft button.
OR
Press ANS/RLS button to select all trunk use
Group.
(005) USE (304)
4. Press Volume button to select YES/NO option.
OR
Dial 1 for YES or 0 for NO and press Right
Soft button to move cursor to ANS option.
(005) USE (304)
DIAL:YES ANS:YES
DIAL:YES ANS:YES
(ALL) USE (301)
DIAL:YES ANS:YES
DIAL:YES ANS:YES
(005) USE (ALL)
DIAL:YES ANS:YES
DIAL:NO
ANS:YES
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Press Volume button to select YES/NO Option.
OR
Dial 1 for YES or 0 for NO and press Right
Soft button to return to step 2.
(005) USE (304)
DIAL:NO
ANS:YES
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 316
MMC 317
MMC 428
MMC 614
© SAMSUNG Electronics Co., Ltd.
COPY STATION/TRUNK USE
ASSIGN STATION/STATION USE
ASSIGN TRUNK/TRUNK USE
STATION/TRUNK USE GROUP
2-81
CHAPTER 2. MMC Programming
[305] ASSIGN FORCED CODE
This MMC allows only one of the four options to be selected; the assignment of account
code with verification, account code without verification, authorization codes, or none on a
per-station basis or on an all-station basis. The system supports 500 authorization codes.
The system supports 999 account codes that are verified when account codes verified is
selected. If account codes without verification is selected, then there will be no table used.
No
Type
Description
0
NONE
No Account or Authorization code required
(NOT forced strictly voluntary).
1
AUTHORIZE CODE
Forces user to enter a valid over four digit Authorization code
listed in AUTHORIZATION CODE Table(MMC 707).
2
ACCT VERIFIED
Forces user to enter a valid account code listed in ACCOUNT
CODE Table(MMC 708).
3
ACCT NO VERIFIED
Forces user to enter an account code but this code is NOT
verified. User can make up any code(any account code up to
12 digits including and #).
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 305.
Display shows:
[201] FORCD CODE
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
[205] FORCD CODE
3. Dial a feature option 0-3.(e.g., 2)
OR
Press Volume button to select option and press
Right Soft button to return step 2.
[205] FORCD CODE
NONE
NONE
ACCT VERIFIED
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 707
MMC 708
2-82
AUTHORIZATION CODE
ACCOUNT CODE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[306] HOT LINE/OFF HOOK SELECTION
Allows a station the ability to make a predetermined call similar to a ring down circuit,
upon the expiration of a timer(see MMC 502 STN TIMERS, Off-Hook Selection Timer).
CONDITIONS
The hotline destination can be a station, a station group, a trunk, a trunk group or an
external number.
There can be a maximum of 18 digits in the dial string for the external number.
The access code for the trunk or trunk group access code is not counted as part of the 18.
DEFAULT DATA
NONE
PROGRAM BUTTONS
B
C
D
E
Used to insert a flash code ‘F’
Used to insert a pause code ‘P’
Used to insert a pulse/tone conversion code ‘C’
Used to mask/unmask following digits-shows as ‘[’ or ‘] ’
ACTION
DISPLAY
1. Press Transfer button and enter 306.
Display shows:
[201] HOT LINE
2. Dial station number.
OR
Use Volume button to scroll through stations
Press Right Soft button to move the cursor.
[205] HOT LINE
3. Enter the hot line destination ie a station or
trunk ID(e.g., 9 or 701) with a maximum of
18 outgoing digits after the access code for
the CO call.(see above list of options if needed)
[205] HOT LINE
NONE
NONE
9-1305P4264100_
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 502
© SAMSUNG Electronics Co., Ltd.
STN TIMERS, OFF-HOOK SELECTION TIMER
2-83
CHAPTER 2. MMC Programming
[308] ASSIGN BACKGROUND MUSIC SOURCE
Assigns a background music source to the phones. There are 6 possible music selections
depending on the number of MISC(daughter) boards that are installed in the system.
CONDITIONS
You may also select an Auto Attendant(AA) port to provide continuous play of a
specific recording. The AA port selected must be the last port on the card. If selected,
the BGM source will be the message defined in MMC 739 from the port defined in this
MMC.
For example, if this MMC selects 201 s music source as 3966(the last port on the
second AA card) and MMC 739 selects Message 20 for the second AA card, when
extension 201 is placed on hold, 201 will hear message 20 from the second installed
AA card.
If you have a SVMi Voice Mail System installed you may also select a SVMi
recording as a music. The recording must already been defined in MMC 756 and will
show up here as the SVMi port assigned with the recording.
To use an external sound source, connect the corresponding port of the terminal box to
the external sound source of the MISC card. If ‘NONE’ is set for background music or
if a sound source is not connected to the external sound source port designated as the
background music source, music will not be played even if the background music
function is enabled.
DEFAULT DATA
NONE
ACTION
2-84
DISPLAY
1. Press Transfer button and enter 308.
Display shows current setting:
[201] BGM SOURCE
2. Dial phone number.(e.g., 205)
OR
Use Volume button to scroll through phone
numbers and press Right Soft button to move
the cursor.
OR
Press ANS/RLS button to select all stations.
[205] BGM SOURCE
3. Enter source number.(e.g., 371)
OR
Press Volume button to make selection and
press Right Soft button to return to step 2.
[205] BGM SOURCE
BGM SOURCE:NONE
BGM SOURCE:NONE
[ALL] BGM SOURCE
BGM SOURCE:?
BGM SOURCE:371
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 309
MMC 408
MMC 736
MMC 756
© SAMSUNG Electronics Co., Ltd.
ASSIGN STATION MOH SOURCE
ASSIGN TRUNK MOH SOURCE
ASSIGN AA MOH
ASSIGN VM MOH
2-85
CHAPTER 2. MMC Programming
[309] ASSIGN STATION MOH SOURCE
Assigns a Music on Hold source to the phones. Any BGM source may be selected. Only
one external music source is provided per MISC(daughter) board.
CONDITIONS
In addition to TONE or a music a source from a MISC daughter board, you may also
select an AA port to provide continuous play of a specific recording. The AA port
selected must be the last port on the card. If selected, the Music on Hold will be the
message defined in MMC 739 from the port defined in this MMC.
For example, if this MMC selects 201 music source as 3966(the last port on the second
AA card) and MMC 739 selects Message 20 for the second AA card, when extension
201 is placed on hold, 201 will hear Message 20 from the second installed AA card.
If you have a SVMi Voice Mail System installed you may also select a SVMi
recording as a music. The recording must already been defined in MMC 756 and will
show up here as the SVMi port assigned with the recording.
To use an external sound source, connect the corresponding port of the terminal box to
the external sound source of the MISC card.
DEFAULT DATA
TONE
ACTION
DISPLAY
1. Press Transfer button and enter 309.
Display shows current setting:
[201] STN MOH
2. Dial phone number.(e.g., 205)
OR
Use Volume button to scroll through phone
numbers and press Right Soft button to move
the cursor.
OR
Press ANS/RLS button to select all stations.
[205] STN MOH
3. Enter source number.(e.g., 371)
OR
Press Volume button to make selection and
press Right Soft button to return to step 2.
[205] STN MOH
MOH SOURCE:NONE
MOH SOURCE:NONE
[ALL] STN MOH
MOH SOURCE:?
MOH SOURCE:371
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
2-86
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
RELATED ITEMS
MMC 308
MMC 736
MMC 756
© SAMSUNG Electronics Co., Ltd.
ASSIGN BACKGROUND MUSIC SOURCE
ASSIGN AA MOH
ASSIGN VM MOH
2-87
CHAPTER 2. MMC Programming
[310] LCR CLASS OF SERVICE
Assigns the LCR class of service allowed on a per-station/per-trunk basis. There are eight
classes which may be assigned. LCR class of service allows specific users to trunk advance
up to a matching LCR class of service programmed in MMC 712.
CONDITIONS
NONE
DEFAULT DATA
LEAST COST ROUTING COS: 1
ACTION
DISPLAY
1. Press Transfer button and enter 310.
Display shows:
[201] LCR CLASS
2. Dial station/trunk number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
OR
Press ANS/RLS button to select all stations.
[205] LCR CLASS
3. Dial 1-8 to select class type.(e.g., 3)
OR
Press Volume button to select class type and
press Right Soft button to return to step 2.
[205] LCR CLASS
LCR CLASS 1
LCR CLASS 1
[ALL] LCR CLASS
LCR CLASS ?
LCR CLASS 3
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
LCR PROGRAMMING
MMC 710
MMC 711
MMC 712
MMC 713
2-88
LCR DIGIT TABLE
LCR TIME TABLE
LCR ROUTE TABLE
LCR MODIFY DIGIT TABLE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[312] ALLOW CALLER ID
Allows the system administrator or technician to allow or deny CID data to be send or
displayed at with LCD phones.
Option
Description
RCV
Set whether to display CID.
SEND
Set whether to send CID for ISDN calls.
CONDITIONS
NONE
DEFAULT DATA
RCV: YES
SND: YES
ACTION
DISPLAY
1. Press Transfer button and enter 312.
Display shows:
[201] ALLOW CLIP
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
OR
Press ANS/RLS button to select all.
[205] ALLOW CLIP
3. Dial 0 or 1 to select receive option.
OR
Press Volume button to select receive option and
press Right Soft button to move cursor.
[205] ALLOW CLIP
4. Dial 0 or 1 to select send option.
OR
Press Volume button to select send option and
press Right Soft button to return to step 2.
[205] ALLOW CLIP
RCV:YES SND:YES
RCV:YES SND:YES
[ALL] ALLOW CLIP
RCV:YES SND:YES
RCV:YES SND:YES
RCV:YES SND:YES
5. Press Transfer button and enter to exit.
OR
Press Speaker button to save and advance to next MMC.
RELATED ITEMS
MMC 119
MMC 425
© SAMSUNG Electronics Co., Ltd.
CALLER ID DISPLAY
ASSIGN CALLER ID TRUNKS
2-89
CHAPTER 2. MMC Programming
[314] CONFIRM OUTGOING CALL
Allows the outgoing call restricted by call duration time, disconnect or confirm with tone.
No
Type
Description
0
NONE
No action
1
CONFIRM TONE
When a Trunk Line confirm tone time expire, a call user heard
system confirmation tone and next a Trunk Line confirm tone
time started.
2
DISCONNECT
When a Trunk Line confirm tone time expire, a call is
disconnected.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 314.
Display shows:
[201] CO CONFIRM
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and use
Right Soft button to move cursor.
OR
Press ANS/RLS button to select all stations.
[205] CO CONFIRM
3. Dial a feature option 0-2.
OR
Press Volume button to make selection and
press Right Soft button to return to step 2.
[205] CO CONFIRM
NONE
NONE
[ALL] CO CONFIRM
NONE
CONFIRM TONE
4. Press Transfer button and enter to save and exit.
OR
Press Speaker button to save and advance to next MMC.
RELATED ITEMS
MMC 501
2-90
SYSTEM WIDE TIMER
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[315] CUSTOMER SET RELOCATION
Customer Set Relocation allows System Administration level or Technician level access to
relocate or exchange similar stations in the system without wiring changes(see Allow Table
below). This program is a one for one exchange with like stations.(e.g., Single line to single
line, 6 button phone to 6 button phone, etc.) All individual station assignments such as
trunk ring, station group, station COS, station speed dial, button appearances, etc. will
follow the Customer Set Relocation program. 12 button phones and 24 button phones can
be exchanged. 48 button modules and 64 button modules can also be exchanged. Single
line stations numbers can be exchanged. If incompatible set types are selected the system
will provide an ERROR: NO MATCH message. If 48 or 64 button module units are to be
exchanged the Master assignment must be removed prior to using Customer Set relocation.
If the 48 or 64 button module Master station is not removed the error code ERROR: NOT
ALONE will appear on the LCD display. A station must be in the idle state(on hook) to
perform Customer Set Relocation. If a wired location has a station port connected but no
telephone instrument the Customer Set Relocation program will allow set relocation as
long as the station types are similar.
12 button and 24 button assignments should be taken in consideration when relocating
these types of sets due to the button configurations of the instruments.
If a 12 button set and a 24 button set are exchanged using the Customer Set Relocation
program the first twelve buttons on the 24 button set will have the button programming of
the 12 button set. The 12 button set will then have the programming of the first twelve
buttons of the 24 button set. In other words, when exchanging 12 and 24 button set only the
first twelve buttons will swapped.
© SAMSUNG Electronics Co., Ltd.
2-91
CHAPTER 2. MMC Programming
Table 2.1
S/L
Customer Set Relocation Allow Table
DS-
DS-
DS-
DS-
DS-
DS-
DS-
DS-
DS-
DS-
DS-
IP-
IP-
IP-
6B
12B
24B
48B
64B
28B
18B
8B
21D
14D
12L
21D
14D
12L
S/L
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
DS-
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
6B
DS12B
DS24B
DS48B
DS64B
DS28B
DS18B
DS8B
DS21D
DS14D
DS12L
IP21D
IP14D
IP12L
2-92
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
CONDITIONS
Custom`er access to this feature is default OFF in MMC 802.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 315.
Display shows:
SET RELOCATION
2. Enter first station number.(e.g., 202)
press Right Soft button to move cursor.
SET RELOCATION
3. Enter second station number.(e.g., 210)
Press Right Soft button to enter data.
SET RELOCATE
4. Display will return to step 1.
Go to step 2.
SET RELOCATION
EXT_
EXT202
EXT202
EXT_
EXT
EXT_
EXT210
EXT
5. Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-93
CHAPTER 2. MMC Programming
[316] COPY STN/TRK USE
Provides a tool for duplicating station/trunk use assignments in MMC 304 from one station
user group to another. This can be done on a per-station use group basis or on all station use
groups.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 316.
Display shows:
(001)COPY USABLE
2. Enter station use group number.(e.g., 005)
OR
Press Volume buttons to make selection and
press Right Soft button to move cursor.
(005)COPY USABLE
3. Enter station use group number to copy from
Cursor is returned to step 2.
OR
Press Volume button to make selection.
(005)COPY USABLE
FROM:NONE
FROM:NONE
FROM:003
4. Press Right Soft button to return to step 2.
OR
Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 304
MMC 317
MMC 428
MMC 614
2-94
ASSIGN EXTENSION/TRUNK USE
ASSIGN STATION/STATION USE
ASSIGN TRUNK/TRUNK USE
STATION/TRUNK USE GROUP
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[317] ASSIGN STATION/STATION USE
This MMC is used to allow or restrict stations from making intercom calls to each other
within the same tenant.
CONDITIONS
NONE
DEFAULT DATA
DIAL: YES
ACTION
DISPLAY
1. Press Transfer button and enter 317.
Display shows:
(001) USE (001)
2. Dial the station use group number.(e.g., 005)
OR
Press Volume button to select station and
press Right Soft button.
OR
Press ANS/RLS button to select all station use
Groups.
(005) USE (001)
3. Dial the station use group number.(e.g., 004)
OR
Press Volume button to select station and
press Right Soft button.
(005) USE (004)
4. Dial 1 for YES or 0 for NO.
OR
Press Volume button to select YES/NO and
press Right Soft button to move cursor.
(005) USE (004)
DIAL:YES
DIAL:YES
(ALL) USE (001)
DIAL:YES
DIAL:YES
DIAL:NO
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 304
MMC 316
MMC 428
MMC 614
© SAMSUNG Electronics Co., Ltd.
ASSIGN EXTENSION/TRUNK USE
COPY STATION/TRUNK USE
ASSIGN TRUNK/TRUNK USE
STATION/TRUNK USE GROUP
2-95
CHAPTER 2. MMC Programming
[318] DISTINCTIVE RINGING
Allows the technician to select the ring tone heard at a phone when called by a specific
station or when a specific trunk rings that phone. There is also a cadence control option to
perform a similar function for single line sets. There are eight ring tones available along
with a Follow Station(NO) option for the phones. There are 5 cadences and a follow station
option for SLT’s.
It also allows the technician to assign the call priority for a group call when called by a
specific station or when a specific trunk rings that phone. When calls into station group
come and group members are all busy, the system will assign a priority to a specific station
or a specific trunk so that calls from a high priority call will be placed at the front of the
group queue. If this option sets NO, the longest call that placed at the group queue has the
highest priority. There are 9 priority levels: priority 1 is the highest and priority 9 is the
lowest.
Option
TONE
Option
No
Description
Calls will ring with the phone users choice of ring frequency.
1~8
Calls from the programmed station or trunk will ring phones with this ring
frequency.
CADENCE
Option
Calls will ring with the normal SLT ring cadences.
1
Calls from the programmed station or trunk will ring SLT’s with the intercom ring
cadence.
2
Calls from the programmed station or trunk will ring SLT’s with the CO ring
cadence.
3
Calls from the programmed station or trunk will ring SLT’s with the DOOR ring
cadence.
4
Calls from the programmed station or trunk will ring SLT’s with the ALARM ring
cadence.
5
Calls from the programmed station or trunk will ring SLT’s with the CALLBACK
ring cadence.
CONDITIONS
Rings of digital phones are distinguished by their tone. If the T(TONE) of the
originating internal/external station is set to ‘NO’, the bell rings according to the
‘MMC 111 PHONE RING TONE’ of the terminating station. If the T is set to 1-8, the
bell rings according to the designated ring tone.
Rings of common phones are distinguished by their ringing interval. If the
C(CADENCE) of the originating internal/external station is set to ‘NO’, the bell rings
according to the interval of ‘MMC 510 SLI RING CADENCE’ for each originating
station type. If the C is set to 1-5, the bell rings according to the interval set at ‘MMC
510 SLI RING CADENCE’ regardless of the originating station type.
2-96
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
DEFAULT DATA
T: NO
C: NO
PRI: NO
FOLLOW STATION SETTING
FOLLOW STATION SETTING
ACTION
DISPLAY
1. Press Transfer button and enter 318.
Display shows first station:
[201] RING TONE
2. Dial trunk or station number.(e.g., 705)
OR
Press Volume button to select trunk or station
and press Right Soft button to move cursor.
[705] RING TONE
3. Dial 1-8 to select ring tone.
OR
Press Volume button to select ring tone and
press Right Soft button to move cursor.
[705] RING TONE
4. Dial 1-5 to select ring cadence
OR
Press Volume button to select ring cadence and
press Right Soft button to move cursor.
[705] RING TONE
5. Enter priority level via dial keypad.
(1-9 or NO)
[705] RING TONE
T:NO C:NO PRI:NO
ÌæÒÑ ÝæÒÑ ÐÎ×æÒÑ
Ìæë ÝæÒÑ ÐÎ×æÒÑ
T:5 C:3 ÐÎ×æÒÑ
T:5 C:í ÐÎ×æÒÑ
6. Press Transfer button and enter to exit.
OR
Press Speaker button to save and advance to next MMC.
RELATED ITEMS
MMC 111
© SAMSUNG Electronics Co., Ltd.
PHONE RING TONE
2-97
CHAPTER 2. MMC Programming
[319] BRANCH GROUP
Allows the assignment of stations into branch groups. There is a maximum of 99 branch
groups. When CO ring is ringing at station assigned the same branch group can answer the
incoming call by off hook.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 319.
Display shows:
[201] BRANCH GRP
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and use
Right Soft button to move cursor.
OR
Press ANS/RLS button to select all stations.
[205] BRANCH GRP
3. Dial a branch group number.(01-99)
OR
Press Volume button to make selection and
press Right Soft button to return to step 2.
[205] BRANCH GRP
BRANCH GRP:NONE
BRANCH GRP:NONE
[ALL] BRANCH GRP
BRANCH GRP:??
BRANCH GRP:10
4. Press Transfer button and enter to save and exit.
OR
Press Speaker button to save and advance to
next MMC.
RELATED ITEMS
NONE
2-98
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[320] PRESET FWD NO ANSWER
Allows a technician to assign a default destination for FNA to each station on the system.
These destinations may be different for each station or they may be the same. The preset
FNA destination will be temporarily overwritten if the station user enters a different FNA
destination. If you cancel the new destination, the preset destination will once more be in
effect. Preset Forward No Answer time follows the station no answer forward timer.
Preset forward no answer can be assigned respectively for each type of call.
No
Type
Description
0
INT
Preset forward no answer applies only to intercom call.
1
EXT
Preset forward no answer applies only to incoming call.
2
BOTH
Preset forward no answer applies to both intercom and incoming call.
When setting PRE FWD BUSY in MMC 210
If MMC 210 PRE FWD BUSY sets ON, the forward busy follows this feature.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 320.
Display shows:
[201] PRESET FNA
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
OR
Press ANS/RLS button to select all stations.
[205] PRESET FNA
3. Dial valid number via keypad.
OR
Press Volume button to select call type and press
Right Soft button to move cursor.
[205] PRESET FNA
© SAMSUNG Electronics Co., Ltd.
NONE
NONE
OPT:BOTH
OPT:BOTH
[ALL] PRESET FNA
NONE
202
OPT:BOTH
OPT:BOTH
2-99
CHAPTER 2. MMC Programming
4. Dial call type.(0, 1 or 2)
OR
Press Volume button to make selection and
press Right Soft button to return to step 2.
[205] PRESET FNA
202
OPT:EXT
5. Press Transfer button and enter to save and exit.
OR
Press Speaker button to save and advance to next
MMC.
RELATED ITEMS
MMC 102
MMC 210
MMC 502
2-100
FORWARDING
CUSTOMER ON/OFF PER TENANT
STATION FWD NO ANS TIMER
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[323] CALLING PARTY NUMBER
Allows a maximum 16 digits number to be entered and associated with a station or trunk
number on a per PRI/BRI basis. When this station makes an outgoing call on this PRI, the
maximum 16 digits number entered will be the Calling Party Number sent on this outgoing
PRI call. There are 4 tables for system.
In case of empty, system use MMC 405 CO TRUNK NUMBER for the Calling Party
Number.
CONDITIONS
NONE
DEFAULT DATA
EMPTY
ACTION
DISPLAY
1. Press Transfer button and enter 323.
Display shows:
[201] SEND CLIP
2. Dial extension or trunk number.(e.g., 230)
OR
Press Volume button to select extension and
press Right Soft button to move the cursor.
[230] SEND CLIP
3. Dial table number.
OR
Press Volume button to select table number and
press Right Soft button to move the cursor.
[230] SEND CLIP
4. Enter the Calling Party Number.
[230] SEND CLIP
1:
1:
2:
2:3055922900
5. Repeat Step 3 & 4 to enter other tables and
Calling Party Numbers.
OR
Repeat Steps 2, 3, & 4 to enter other station or
trunk and Calling Party Numbers.
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
© SAMSUNG Electronics Co., Ltd.
2-101
CHAPTER 2. MMC Programming
RELATED ITEMS
MMC 405
MMC 420
MMC 419
MMC 834
MMC 837
2-102
CO TRUNK NUMBER
PRI OPTIONS
BRI OPTIONS
VOIP H.323 OPTIONS
VOIP SIP OPTIONS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[400] CUSTOMER ON/OFF PER TRUNK
Assigns several options(listed below) on a per-trunk basis.
No
0
Option
1A2 EMULATION
Default
OFF
Description
When this option is set to ON up to 4 internal stations
can participate in a conversation on this trunk by
pressing the trunk key.
1
TRUNK INC DND
OFF
When this option is set to ON a trunk that is
programmed to ring a specific station(a private line or
DIL) will ring at that station if the station is in DND.
2
TRUNK FORWARD
ON
When this option is set to OFF this trunk will not follow a
ringing stations call forwarding.
2
LCR ALLOW
OFF
When this option is set to ON, if the station access this
trunk will re-route via LCR outgoing. This feature
available in Australia, New Zealand, Italy and U.K. only
4
MOH/BGM USE
OFF
When this option is set to ON, this trunk uses MOH
source. This feature available Australia’s 8TRK/7TRK only.
6
EFWD EXT CLI
ON
This option determines what kinds of CLI number will be
sent to the external forwarded outgoing call.
(Station or Received CLI from Trunk)
7
REPEAT CLI
ON
This option determines what kinds of CLI number will be
sent to the trunk to trunk call.
(Trunk or Received CLI from Trunk)
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
SOME OPTIONS ARE DEPEND ON COUNTRY
© SAMSUNG Electronics Co., Ltd.
2-103
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 400.
Display show:
[701] TRK ON/OFF
2. Dial trunk number.(e.g., 704)
OR
Press Volume button to select trunk.
OR
Press ANS/RLS button for all trunks and press
Right Soft button to move cursor to options.
[704] TRK ON/OFF
3. Dial option number from above list.(0-4)
OR
Press Volume button to select option and press
Right Soft button to move cursor.
[704] TRK ON/OFF
4. Dial 1 for ON or 0 for OFF.
OR
Press Volume button to select ON/OFF and
press Right Soft button to return to step 2.
[704] TRK ON/OFF
1A2 EMULATE:OFF
1A2 EMULATE:OFF
[ALL] TRK ON/OFF
1A2 EMULATE:?
TRK FORWARD:ON
TRK FORWARD:OFF
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 405
MMC 323
MMC 714
CO TRUNK NUMBER
CALLING PARTY NUMBER
DID NUMBER AND NAME TRANSLATION
LCR PROGRAMMING
MMC 710
MMC 711
MMC 712
MMC 713
LCR DIGIT TABLE
LCR TIME TABLE
LCR ROUTE TABLE
LCR MODIFY DIGIT TABLE
CALL FORWARD
MMC 102
MMC 301
MMC 501
MMC 502
MMC 701
MMC 722
MMC 723
2-104
CALL FORWARD
ASSIGN STATION COS
SYSTEM TIMERS
STATION TIMERS
ASSIGN COS CONTENTS
STATION KEY PROGRAMMING
SYSTEM KEY PROGRAMMING
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[401] TRUNK LINE/PBX LINE
Used to select the mode of the Trunk line. If the PBX mode is chosen, this allows PBX
access codes to be recognized, thus allowing more complete toll restriction(call barring).
This mode is assigned on a per-trunk basis.
CONDITIONS
NONE
DEFAULT DATA
ALL TRUNK LINES
ACTION
DISPLAY
1. Press Transfer button and enter 401.
Display shows:
[701] PBX LINE
2. Dial trunk number.(e.g., 704)
OR
Use Volume button to scroll through trunk
numbers and press Right Soft button to move.
OR
Press ANS/RLS button to select all.
[704] PBX LINE
3. Dial 1 for PBX or 0 for Trunk Line.
OR
Use Volume button to scroll through options
Press Right Soft button to return to step 2.
[704] PBX LINE
CO LINE
CO LINE
[ALL] PBX LINE
?
PBX LINE
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-105
CHAPTER 2. MMC Programming
[402] TRUNK DIAL TYPE
Used to determine the dialling type of each Trunk line. There are three options:
No
Type
Description
0
DTMF TYPE
Dual Tone Multi-Frequency
1
DIAL PULSE TYPE
DIAL PULSE
2
R2MFC TYPE
R2- Frequency
CONDITIONS
NONE
DEFAULT DATA
ALL TRUNKS: DTMF
ACTION
DISPLAY
1. Press Transfer button and enter 402.
Display shows:
[701] DIAL TYPE
2. Dial trunk number.(e.g., 704)
OR
Use Volume button to scroll through trunk numbers
and press Right Soft button to move the cursor.
OR
Press ANS/RLS button to select all.
[704] DIAL TYPE
3. Dial 0 for DTMF, 1 for PULSE or 2 for
R2MFC TYPE.
OR
Use Volume button to scroll through options
Press Right Soft buttons to return to step 2.
[704] DIAL TYPE
DTMF TYPE
DTMF TYPE
[ALL] DIAL TYPE
?
DIAL PULSE TYPE
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 501
MMC 503
2-106
SYSTEM TIMERS
TRUNK-WIDE TIMERS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[403] TRUNK TOLL CLASS
Assigns toll class level assignments on a per-trunk or all-trunk basis in a day or night
condition. The options for toll level will follow either the station class or the class of
service defined in MMCs 702, Toll Deny Table, and 703, Toll Allowance Table.
The toll classes that are available are listed below with their entry numbers.
No
Class
Description
0
F-STN
Follow station toll restriction
1
CLS-A
Follow toll class A(Unrestricted)
2
CLS-B
Follow toll class B
3
CLS-C
Follow toll class C
4
CLS-D
Follow toll class D
5
CLS-E
Follow toll class E
6
CLS-F
Follow toll class F
7
CLS-G
Follow toll class G
8
CLS-H
Follow toll class H(All restricted)
CONDITIONS
NONE
DEFAULT DATA
ALL TRUNKS: F-STN
ACTION
DISPLAY
1. Press Transfer button and enter 403.
Display shows:
[701] TOLL CLASS
2. Dial trunk number.(e.g., 704)
OR
Use Volume button to scroll through trunk numbers
and press Right Soft button to move the cursor.
OR
Press ANS/RLS button to select all.
[704] TOLL CLASS
3. Dial ring plan number.(1~6)
OR
Use Volume button to scroll through ring plan
numbers and press Right Soft button to move
the cursor.
[704] TOLL CLASS
© SAMSUNG Electronics Co., Ltd.
1:F-STN 2:F-STN
1:F-STN 2:F-STN
[ALL] TOLL CLASS
1:F-STN 2:F_STN
1:F-STN 2:F-STN
2-107
CHAPTER 2. MMC Programming
4. Enter day toll class.(e.g., 2 for CLS-B)
OR
Press Volume button to scroll through toll classes
and use Right Soft button to move the cursor.
[704] TOLL CLASS
1:CLS-B 2:F-STN
5. Press Transfer button and enter to store data and exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 301
MMC 507
MMC 701
ASSIGN STATION COS
ASSIGN AUTO RING PLAN TIME
ASSIGN COS CONTENTS
TOLL RESTRICTION
MMC 702
MMC 703
MMC 704
MMC 709
2-108
TOLL DENY TABLE
TOLL ALLOWANCE TABLE
ASSIGN WILD CHARACTER
TOLL PASS CODE/SPECIAL CODE TABLE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[404] TRUNK NAME
Allows an 11-character name to be entered to identify an individual trunk.
CONDITIONS
NONE
INPUT CHARACTERS
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 404.
Display shows:
[701] TRUNK NAME
2. Dial trunk.(e.g., 704)
OR
Press Volume button to select trunk and press
Right Soft button to move the cursor.
[704] TRUNK NAME
3. Enter trunk name using the procedure
described above Press Right Soft button to
return to step 2.
[704] TRUNK NAME
TELECOMS
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
DEFAULT DATA
NONE
RELATED ITEMS
MMC 104
MMC 405
© SAMSUNG Electronics Co., Ltd.
STATION NAME
TRUNK NUMBER
2-109
CHAPTER 2. MMC Programming
[405] TRUNK CO TEL NUMBER
Allows an 11-digit number to be entered to identify an individual trunk.
CONDITIONS
NONE
INPUT NUMBERS
Numbers are written using the keypad. Each press of a key selects a digit. Pressing the
desired key moves the cursor to the next position. For example, if the directory number is
426-4100, press the number 4 once to get the number 4. Now press the number 2 once for
number 2. Continue selecting characters from the table below to complete your number.
When the number you want appears on the same dial pad key as the previous
number, press the Volume Up button to move the cursor to the right or the
Volume Down button to move the cursor left. A space can be entered by using
these keys.
COUNT
1
2
3
4
5
DIAL 0
0
<
>
.
)
DIAL 1
1
Space
?
,
!
DIAL 2
2
A
B
C
@
DIAL 3
3
D
E
F
#
DIAL 4
4
G
H
I
$
DIAL 5
5
J
K
L
%
DIAL 6
6
M
N
O
^
DIAL 7
7
P
Q
R
S
DIAL 8
8
T
U
V
*
DIAL 9
9
W
X
Y
Z
DIAL *
*
:
[
]
=
The # button can be used for special characters:
#, space, &, !, :, ?, ., %, $, -, <, >, /, = , [, ], @, ^, (, ), _, +, {, }, |, ; , \ , " , ~.
DEFAULT DATA
NONE
2-110
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
ACTION
DISPLAY
1. Press Transfer button and enter 405.
Display shows:
[701] CO TEL NO.
2. Dial trunk.(e.g., 704)
OR
Press Volume button to select trunk and press
Right Soft button to move the cursor.
[704] CO TEL NO.
3. Enter trunk number using the procedure described
above.
[704] CO TEL NO.
3054264100
4. Press Right Soft button to return to step 2.
OR
Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 404
© SAMSUNG Electronics Co., Ltd.
TRUNK NAME
2-111
CHAPTER 2. MMC Programming
[406] TRUNK RING ASSIGNMENT
Enables ringing to a specific station or to a group of stations when incoming calls are
received. This MMC controls ring plan destinations for ring down trunks. If the ring plan
destinations are not input the default ring plan is ring plan 1. Station group 500 is default in
Ring Plan 1.
CONDITIONS
NONE
DEFAULT DATA
ALL TRUNKS RING DEFAULT OPERATOR GROUP
ACTION
DISPLAY
1. Press Transfer button and enter 406.
Display shows:
[701] TRK RING
2. Dial trunk number.(e.g., 704)
OR
Use Volume button to scroll through trunk numbers
and press Right Soft button to move the cursor.
OR
Press ANS/RLS button for all.
[704] TRK RING
3. Dial ring plan number or press the Right Soft
button to move the next step.
[704] TRK RING
4. Dial station number or station group number.
(e.g., 205)
OR
Press Volume button to make selection and
press Right Soft button to move cursor to the
next ring plan destination and repeat step 5.
OR
Press Left Soft button to return to step 5.
OR
[704] TRK RING
1:500
1:500
2:500
2:500
[All] TRK RING
1:500
1:500
1:205
2:500
2:500
2:500
[704] TRK RING
1:205
2:501
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 202
MMC 507
MMC 601
2-112
CHANGE FEATURE PASSCODES
ASSIGN RING PLAN TIME
ASSIGN STATION GROUP
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[407] FORCED TRUNK RELEASE
Provides a positive forced trunk release to a specific trunk or all trunks in the event of a
trunk lock-up.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 407.
Display shows:
[701] TRK RELS.
2. Dial in trunk number.(e.g., 704)
OR
Press Volume button selected trunk and press
Right Soft button.
OR
Press ANS/RLS button to select all trunks.
[704] TRK RELS.
3. Dial 1 for YES or Dial 0 for NO.
(Pressing 1 or 0 will return to step 2)
[704] TRK RELS.
RELEASE?_Y:1,N:0
RELEASE?_Y:1,N:0
[ALL] TRK RELS.
RELEASE?_Y:1,N:0
RELEASE?_Y:1,N:0
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-113
CHAPTER 2. MMC Programming
[408] ASSIGN TRUNK MOH SOURCE
Allows the system administrator to select which Music On Hold(MOH) source can be
heard on each trunk. For the five types of selections, see below.
Type
Description
TONE
An intermittent tone is played to the caller.
NONE
No Music on Hold selection.
37X
If X is zero(0), a chime tune is played. If X is another number, an
external source from a MISC(daughter) board is played.
39XX(when AA is used)
The MOH source is provided by the AA card. See MMC 736.
SVMi PORT NUMBER
If you have a SVMi Voice Mail System installed you may also select a
SVMi recording as a music source. The recording must already been
defined in MMC 756 and will show up here as the SVMi port associated
with the recording.
CONDITIONS
To use an external sound source, connect the corresponding port of the terminal box to the
external sound source of the MISC card.
DEFAULT DATA
TONE
ACTION
2-114
DISPLAY
1. Press Transfer button and enter 408.
Display shows current setting.
[701] TRK MOH
2. Dial trunk number.(e.g., 704)
OR
Use Volume button to scroll through trunk numbers
and press Right Soft button to move cursor.
OR
Press ANS/RLS button to select all.
[704] TRK MOH
3. Enter source number.(e.g., 371)
OR
Press Volume button to select option.
Press Right Soft button to return to step 2 above.
[705] TRK MOH
MOH SOURCE:TONE
MOH SOURCE:TONE
[ALL] TRK MOH
MOH SOURCE:?
MOH SOURCE:371
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 736
MMC 756
© SAMSUNG Electronics Co., Ltd.
ASSIGN AA MOH
ASSIGN VM MOH
2-115
CHAPTER 2. MMC Programming
[409] TRUNK STATUS READ
Allows the status of trunks to be read in a format that will enable the servicing personnel to
quickly identify the ownership and position of a trunk. This is a read-only MMC.
No
Type
Description
00
PORT
Port Number(Cabinet/Slot/Port)
01
TYPE
LOOP, GND, E & M, DID, BRI, PRI, VOIP
02
1A2 EMULATE
1A2 Emulation On/Off
03
TRK FORWARD
Trunk Forward On/Off
04
LINE
CO/PBX
05
DIAL
DTMF/Dial Pulse
06-11
TOLL TYPE 1-6
Ring Plan Toll Restriction(1-6)
12-17
RING PLAN 1-6
Ring Plan Ring Destination(1-6)
18
MOH SOURCE
MOH Source
19
DISA LINE
DISA Status
CONDITIONS
NONE
DEFAULT DATA
FOLLOW TRUNK
ACTION
DISPLAY
1. Press Transfer button and enter 409.
Display shows:
[701] TRK STATUS
2. Enter trunk number via dial keypad.(e.g., 704)
OR
Press Volume button to make selection and
press Right Soft button to advance cursor.
[704] TRK STATUS
3. Enter in desired option 00-12.(e.g., 02)
OR
Press Volume button to make selection.
[704] TRK STATUS
PORT:C1-S5-P01
PORT:C1-S5-P04
TYPE:LOOP TRUNK
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
2-116
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
RELATED ITEMS
MMC 400
MMC 401
MMC 402
MMC 403
MMC 404
MMC 406
MMC 408
MMC 410
© SAMSUNG Electronics Co., Ltd.
CUSTOMER ON/OFF PER TRUNK
TRUNK LINE/PBX LINE
TRUNK DIAL TYPE
TRUNK TOLL CLASS
TRUNK NAME
TRUNK RINGING ASSIGNMENT
ASSIGN TRUNK MUSIC ON HOLD SOURCE
ASSIGN DISA TRUNK
2-117
CHAPTER 2. MMC Programming
[410] ASSIGN DISA TRUNK
Allows the system the ability to have Direct Inward System Access(DISA).
Because there is a possibility that unauthorized calls will be made via this feature, several
safeguards have been added. The end user must be informed of these to prevent
unnecessary service calls. DISA can lockout when a predetermined number of invalid
consecutive calls are attempted. Callers will then receive error tone until the programmable
timer has expired.
CONDITIONS
The * key may be used to initiate new dial tone while in a station to station call.
The # button may be used to terminate the DISA call and disconnect the central office
line. DISA lines must be assigned to the Ring Plan(s).
DEFAULT DATA
ALL TRUNKS: NORMAL
ACTION
DISPLAY
1. Press Transfer button and enter 410.
Display shows:
[701]
123456
2. Dial trunk number.(e.g., 704)
OR
Press Volume button to select trunk and press
Right Soft button.
OR
Press ANS/RLS button to select all trunks.
OR
3. Press Volume button to select a Ring Plan.
OR
Using the dial pad press 1 to apply and 0 not to
apply to a particular Ring Plan and press Right
Soft button to return to step 2.
[704]
123456
[ALL]
123456
[704]
123456
DISA LINE:000000
DISA LINE:000000
DISA LINE:000000
DISA LINE:001000
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 500
MMC 507
2-118
SYSTEM-WIDE COUNTERS
ASSIGN RING PLANS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[411] ASSIGN E1 SIGNAL TYPE
Defines the type of signaling for each E1 trunk assigned to the card. There are four kinds of
trunks as detailed below. There are three types of signaling associated with E & M and DID.
E1 channels(1-30) that are not used should have TYPE programmed as UNUSED.
Trunk
LOOP
E&M
DID
DID
Signaling
Comments
BR_14301_NOT
BRAZIL, L, I, ERICSSON, 1/1914, FOR TEST
BR_14301_OPT
BRAZIL, L, I, ERICSSON, 2/1914, FOR TEST
RU_LOOP
RUSSIA, L, I/O, LOOP START
IMMEDIATE
COMMON, E/D, I/O, IMMEDIATE START
DELAYED
COMMON, E/D, I/O, DELAY
ITU_WINK
COMMON, E/D, I/O, WINK START
ITU_WINK_MPD
COMMON, E/D, I/O, WINK START WITH MPD
BR_CONTINU
BRAZIL, E/D, I/O, CONTINUE
BR_PULSED
BRAZIL, E/D, I/O, PULSED
BR_R2_DIGIT
BRAZIL, E/D, I/O, R2 DIGITAL
BR_BLD_160
BRAZIL, E, I/O, ERICSSON, 2/1914, 14102_N
BR_BLD_157
BRAZIL, E, I/O, ERICSSON, 2/1914, 14102_O
BR_14102_NOT
BRAZIL, E, I/O, ERICSSON, 1/1914
BR_14102_OPT
BRAZIL, E, I/O, ERICSSON, 1/1914
RU_ADSE
RUSSIA, E/D, I/O, PABX
RU_HARRIS_UK
RUSSIA, E/D, I/O, HARRIS, PABX, UK_EM
RU_USER_ROM
RUSSIA, E/D, I/O, USER ROM
AR_WINK
ARGENTINA, E/D, I/O, WINK
AR_WINK_MPD
ARGENTINA, E/D, I/O, WINK-MPD
CHINA_NO1
CHINA, E/D, I/O, NO.1 OF CHINA
POL_WINK_MPD
POLAND, E/D, I/O, POLAND WINK MPD
IMMEDIATE
COMMON, E/D, I/O, IMMEDIATE START
DELAYED
COMMON, E/D, I/O, DELAY
ITU_WINK
COMMON, E/D, I/O, WINK START
ITU_WINK_MPD
COMMON, E/D, I/O, WINK START WITH MPD
BR_CONTINU
BRAZIL, E/D, I/O, CONTINUE
BR_PULSED
BRAZIL, E/D, I/O, PULSED
BR_R2_DIGIT
BRAZIL, E/D, I/O, R2 DIGITAL
RU_ADSE
RUSSIA, E/D, I/O, PABX
RU_HARRIS_UK
RUSSIA, E/D, I/O, HARRIS, PABX, UK_EM
RU_USER_ROM
RUSSIA, E/D, I/O, USER ROM
AR_WINK
ARGENTINA, E/D, I/O, WINK
AR_WINK_MPD
ARGENTINA, E/D, I/O, WINK-MPD
CHINA_NO1
CHINA, E/D, I/O, NO.1 OF CHINA
POL_WINK_MPD
POLAND, E/D, I/O, POLAND WINK MPD
UNUSE
© SAMSUNG Electronics Co., Ltd.
2-119
CHAPTER 2. MMC Programming
CONDITIONS
An E1 card must be installed in the OfficeServ 500 system. Otherwise, the ‘NO E1
TRUNK CARD’ message is displayed.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 411.
Display shows:
[701] E1 SIGNAL
2. Enter desired trunk number.(e.g., 705)
OR
Press Volume button to make selection.
Press Right Soft button to move cursor.
OR
Press ANS/RLS button to select all trunks.
[705] E1 SIGNAL
3. Press Volume button to trunk type select and
press Right Soft button to move cursor.
[705] E1 SIGNAL
4. Press Volume button to signaling select and
press Right Soft button to move cursor.
[705] E1 SIGNAL
UNUSE
UNUSE
[ALL] E1 SIGNAL
?
E&M:IMMEDIATE
E&M:ITU_WINK
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
TRUNK PROGRAMMING
MMC 400
MMC 401
MMC 402
MMC 403
MMC 404
MMC 405
MMC 406
MMC 407
MMC 408
MMC 409
2-120
CUSTOMER ON/OFF PER TRUNK
TRUNK LINE/PBX LINE
TRUNK DIAL TYPE
TRUNK TOLL CLASS
TRUNK NAME
TRUNK CO TEL NUMBER
TRUNK RING ASSIGNMENT
FORCED TRUNK RELEASE
ASSIGN TRUNK MOH SOURCE
TRUNK STATUS READ
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
MMC 410
MMC 411
MMC 412
MMC 413
MMC 425
MMC 415
MMC 416
MMC 414
MMC 426
MMC 436
MMC 423
MMC 424
MMC 418
MMC 417
MMC 420
MMC 419
MMC 421
MMC 422
MMC 433
MMC 434
© SAMSUNG Electronics Co., Ltd.
ASSIGN DISA TRUNK
ASSIGN E1 SIGNAL TYPE
ASSIGN TRUNK SIGNAL
VMS CALL TYPE
ASSIGN CALLER ID TRUNKS
REPORT TRUNK ABANDON DATA
ASSIGN E & M/DID RINGDOWN
PRS SIGNAL
TRUNK GAIN CONTROL
TRUNK TMC GAIN
S/T MODE
BRI S0 MAPPING
BRI AND PRI CARD RESTART
E1/PRI CRC4 OPTION
PRI OPTIONS
BRI OPTIONS
MSN DIGIT
TRUNK COS
COST RATE
CONNECTION STATUS
2-121
CHAPTER 2. MMC Programming
[412] ASSIGN TRUNK SIGNAL
Allows for the assignment of analog DID or E & M cards for proper signaling.
This MMC is only for analog types of DID/E & M trunks. These trunks can also use the
translation tables in MMC 714. The signaling condition types are as follows:
No
Signaling condition type
0
IMMEDIATE START
1
DELAYED START
2
WINK START
CONDITIONS
An analog E & M/DID Trunk card must be installed in the OfficeServ 500 system.
Otherwise, the ‘NO E & M/DID TRUNK’ message is displayed.
DEFAULT DATA
IMMEDIATE
ACTION
DISPLAY
1. Press Transfer button and enter 412.
Display shows:
[701] TRK SIGNAL
2. Enter desired trunk number.(e.g., 705)
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
OR
Press ANS/RLS button to select all trunks.
[705] TRK SIGNAL
3. Enter desired trunk type selection from above list.
OR
Press Volume button to make selection and
press Right Soft button.
[705] TRK SIGNAL
IMMEDIATE START
IMMEDIATE START
[ALL] TRK SIGNAL
IMMEDIATE START
WINK START
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 416
MMC 714
2-122
E & M/DID RINGDOWN
DID NUMBER AND NAME TRANSLATION
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[413] VMS CALL TYPE
This program needs when VOICE MAIL/AUTO ATTENDANT(SVM-800) is used.
Defines the type of signaling for voice mail assigned trunk.
Type
Description
Default
AP
ANSWERING PHONE
NO
AT
AUDIO TEX
NO
AA
AUTO ATTENDANT
YES
VM
VOICE MAIL
NO
CONDITIONS
This program needs when VOICE MAIL/AUTO ATTENDANT(SVM-800) is used.
DEFAULT DATA
SEE DESCRIPTION
ACTION
DISPLAY
1. Press Transfer button and enter 413.
Display shows:
[701] CTYPE AP:N
2. Enter desired trunk number.(e.g., 702)
OR
Press Volume button to make selection
Press Right Soft button to move cursor.
OR
Press ANS/RLS button to select all trunks.
[702] CTYPE AP:N
3. Enter 1 for YES, or 0 for NO.
OR
Press Volume button to make selection and
press Right Soft button.
[702] CTYPE AP:N
AT:N AA:Y VM:N
AT:N AA:Y VM:N
AT:N AA:Y VM:N
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-123
CHAPTER 2. MMC Programming
[414] PRS SIGNAL
Used on a per-trunk basis to define if a Trunk line is to be either a Metering Pulse(MPD) or
a Polarity Reversal Signal(PRS) trunk.
A Meter Pulse Trunk will detect a C.O provided meter pulse. A Polarity Reversal trunk will
detect the line reversal signal which may be provided by the Trunk Line When the other
party answers the outgoing call or the outside party clears the call.
There are three types of PRS mode: PRS 1, PRS 2 and PRS 3.
Type
PRS 1
Description
When first PRS is detected, call duration is started. When second PRS is detected,
call duration timer stopped. The call is not released until hanging-on.
PRS 2
When first PRS is detected, call duration timer is started. When second PRS is
detected, call duration timer is stopped and call is released.
PRS 3
The call duration timer starts based on the timer. When first PRS is detected, call
duration timer is stopped and call is released.
CONDITIONS
If the trunk is designated as PRS detection, the call duration timer will be started and
the results printed on the SMDR record.
PRS detection is also essential for dropping a trunk-to- trunk conversation which is
unsupervised by an internal party.
DEFAULT DATA
NORMAL(NONE)
ACTION
2-124
DISPLAY
1. Press Transfer button and enter 414.
Display shows:
[701] TRK PRS
2. Dial desired trunk number.(e.g., 705)
OR
Press Volume button to select trunk and use
Right Soft button to move cursor.
[705] TRK PRS
NONE
NONE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
3. Dial 0 for PRS 1, 1 for PRS 2, 2 for PRS 3 or 3
for MPD or 4 for NORMAL.
OR
Press Volume button to scroll through options and
use Left or Right Soft button to return to step 2.
[705] TRK PRS
PRS 2
4. Press Transfer button and enter to save and exit.
OR
Press Speaker button to save and advance to
next MMC.
RELATED ITEMS
MMC503
© SAMSUNG Electronics Co., Ltd.
TRUNK-WIDE TIMER
2-125
CHAPTER 2. MMC Programming
[415] REPORT TRUNK ABANDON DATA
Allows the system administrator or technician to enable or disable the reporting of
abandoned Trunk Line calls for which CID, CLIP information has been collected on a pertrunk basis. There are two options for this MMC as follows:
No
0
Option
Description
REPORT: NO
Abandoned call records for incoming calls with CID information will not
be printed on SMDR or stored in the system call abandon list.
These records will continue to be stored in the station review list.
1
REPORT: YES
Abandoned call records for incoming calls with CID information will be
printed on SMDR and stored in the system call abandon list.
These records will also be stored in the station review list.
CONDITIONS
In order for these abandoned call records to print on SMDR, MMC 725 SMDR OPTIONS
Option 11 Print Abandoned Call Records must be set to YES.
DEFAULT DATA
ALL TRUNKS REPORT: YES
ACTION
DISPLAY
1. Press Transfer button and enter 415.
Display shows:
[701] TRK ABNDN
2. Dial trunk number.(e.g., 705)
OR
Use Volume button to select trunk and press
Right Soft button to move cursor.
[705] TRK ABNDN
3. Dial 1 for YES or 0 for NO.
OR
Use Volume button to select option and press
Right Soft button to return to step 2.
[705] TRK ABNDN
REPORT:YES
REPORT:YES
REPORT:NO
4. Press Transfer button and enter to save and exit.
OR
Press Speaker button to save and advance to next MMC.
RELATED ITEMS
MMC 725
MMC 425
2-126
SMDR OPTIONS
ASSIGN CALLER ID TRUNKS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[416] ASSIGN E & M/DID RINGDOWN
This MMC defines which ring destination table an E & M or DID trunk will follow
for incoming calls. There are three options for each trunk as defined below.
No
0
Option
FOLLOW INCOM DGT
Description
When a trunk is set to this option calls will ring at the
destination that matches the digits received from the Trunk line.
1
FOLLOW DID TRANS
When a trunk is set to this option calls will ring at the
destination defined in MMC 714 that matches the digits
received from the TRUNK LINE
2
FOLLOW TRK RING
If this option is selected, press Right Soft button and ‘NO. RCV
DIGIT’: will appear on the display. Here is where the number of
incoming digits from Trunk Line must be entered(0 through 4).
When a trunk is set to this option calls will ring at the
destination defined in MMC 406 for that trunk. If the destination
defined in MMC 406 is a VMAA port or group then the system
will repeat the digits received from the CO to the port when it
answers.
CONDITIONS
R2MFC trunk lines only support the ‘FOLLOW INCOM DGT’ and ‘FOLLOW DID
TRANS’ options.
DEFAULT DATA
FOLLOW INCOMING DIGIT
ACTION
DISPLAY
1. Press Transfer button and enter 416.
Display shows:
[701] EM/DD RING
2. Enter desired trunk number.(e.g., 705)
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
OR
Press ANS/RLS button to select all trunks.
[705] EM/DD RING
© SAMSUNG Electronics Co., Ltd.
FOLLOW INCOM DGT
FOLLOW INCOM DGT
[ALL] EM/DD RING
FOLLOW INCOM DGT
2-127
CHAPTER 2. MMC Programming
3. Dial option number.(0~2)
OR.
Press Volume button to make selection and
press Right Soft button to return step2.
If the FOLLOW TRK RING is selected,
the LCD display shows step 4.
[705] EM/DD RING
4. Enter the number of incoming digits.
[705] EM/DD RING
NO. RCV DIGIT:00
NO. RCV DIGIT:00
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 714
2-128
DID NUMBER AND NAME TRANSLATION
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[417] E1/PRI CRC4 OPTION
This option is used to enable/disable CRC4 generation and checking.
CONDITIONS
It is useful with some networks which do not support CRC4 framing but only PCM30
framing.
After changing this option, MMC 425 must be used to restart the card to make the
change effective.
DEFAULT DATA
CRC4: ON
ACTION
DISPLAY
1. Press Transfer button and enter 417.
Display shows:
[701] E1/PRI CRC
2. Enter first trunk number in PRI card.(e.g., 701)
OR
Press Volume button to select trunk and use
Right Soft button to move cursor.
[701] E1/PRI CRC
3. Enter 1 for ON 0 for OFF.
OR
Press Volume button to select and press
Right Soft button.
[701] E1/PRI CRC
ON
ON
OFF
4. Press Transfer button and enter to save and exit.
OR
Press Speaker button to save and advance to next
MMC.
RELATED ITEMS
MMC 418
© SAMSUNG Electronics Co., Ltd.
CARD RESTART
2-129
CHAPTER 2. MMC Programming
[418] BRI AND PRI CARD RESTART
This MMC is used to restart a BRI and a PRI card at the card level. This action is required
to update the processor on the BRI and PRI card to any changes in the card setup MMC’s
and to put these changes into effect.
CONDITIONS
A BRI card or TEPRI card must be installed in the system.
Before setting the PRI program, the J2 jumper of the TEPRI board must be set ‘ON’ to
PRI mode.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 418.
Display shows first BRI or PRI circuit.
[725] RESTART
2. Dial first trunk on a BRI or PRI card.(e.g., 733)
OR
Press Volume button to select the first trunk
and press Right Soft button to move the cursor.
[733] RESTART
3. Dial 1 for YES or Dial 0 for NO.
Pressing 1 will advance to step 4.
[733] RESTART
4. Dial 1 for YES or Dial 0 for NO.
Pressing 1 or 0 will return to step 2.
[733] RESTART
CARD RESTART?NO
CARD RESTART?NO
CARD RESTART?YES
ARE YOU SURE?YES
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
DEFAULT DATA
NONE
RELATED ITEMS
MMC 419
MMC 420
MMC 423
MMC 424
2-130
BRI OPTIONS
PRI OPTIONS
S/T MODE
BRI S0 MAPPING
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[419] BRI OPTIONS
Assigns several options on a per-BRI basis and there are different options depending on
whether the BRI is programmed as a trunk or station in MMC 423.
OPTIONS FOR BRI PORTS PROGRAMMED AS TRUNKS
No
0
Option
Description
CHANNEL
When this option is set to YES, the system will place calls on any free
ANY
channel of that BRI if the channel chosen by the user is busy. If set to NO,
you will receive a busy signal if they attempt to access a busy channel even
if the other channel on that BRI is free.
1
BRI MODE
P-P NOR
BRI access mode select.
Point to Point NORmal. This operates like a standard telephone line with
one CO number per channel and ring according to MMC 406.
P-P DID
Point to Point Direct Inward Dial. This operates in a similar manner to an
analog DID circuit with multiple CO numbers pointed to a single channel
and translated within the system(MMC714) to a single device.
P-M NOR
Point to Multi-point NORmal. This type of circuit operates in a similar
manner to P-P NORmal but allows multiple devices to be attached to the
circuit. Ringing is defined in MMC 406.
P-M MSN
Point to Multi-point MSN. This setting is used when the line uses the MSN
supplementary service. Ringing is defined in MMC 421.
2
3
DLSEND
BRI dial sending mode select.
ENBLOCK
Digits will be collected and sent in a single block similar to a Cell phone.
OVERLAP
Digits will be sent as they are dialled by the user.
CLIP TABLE
Used to select the Calling Party Number to send to the network. In case of
NONE, MMC405 CO TRUNK NUMBER is sent to the network. In other
cases, MMC 323 Calling Party Number entry corresponding with the
selected number is sent to the network.
4
NB TYPE
Used to select the type of the Calling Party Number to send to the network.
UNKNOWN
Unknown number.
INT.NAT
International number.
NATIONAL
National number.
NETWORK
Network specific number.
SUBSCRIB
Subscriber number.
EXTEN
Local number.
ABBREV
Abbreviated number.
© SAMSUNG Electronics Co., Ltd.
2-131
CHAPTER 2. MMC Programming
No
5
Option
NB PLAN
Description
Used to select the type of the Calling Party Number Plan to send to the
network.
UNKNOWN
Unknown numbering plan.
ISDN
ISDN numbering plan(CCITT E.163-164).
DATA
Data numbering plan(CCITT X.121).
TELEX
Telex numbering plan(CCITT F.69).
NATIONAL
National standard numbering plan.
PRIVATE
Private numbering plan.
EXTEN
Local numbering plan.
OPTIONS FOR BRI PORTS PROGRAMMED AS STATIONS
No
Option
0
ANY CHANNEL
Description
When this option is set to YES, the system will place calls on any free
channel of that BRI if the channel chosen by the user is busy(e.g.,
Preferred channel selection). If set to NO, the user will receive a busy
signal if they attempt to access a busy channel even if the other channel
on that BRI is free(e.g., Exclusive channel selection).
1
POWER FEED
This field determines if power to a BRI access will be supplied.(YES or
NO)
CONDITIONS
A BRI card must be installed in the system. Otherwise, the ‘NO BRI CARD’ message
is displayed.
If any changes are made in this MMC, the BRI card that is affected by these changes
MUST be restarted using MMC 425 in order for the changes to become effective.
DEFAULT DATA
For BRI Ports programmed as Trunks:
CHANNEL ANY: YES
BRI MODE: P-P DDI
DLSEND: OVERLAP
CLIP TABLE: NONE
NB TYPE: NATIONAL
NB PLAN: ISDN
For BRI Ports programmed as Stations:
CHANNEL ANY : YES
POWER FEED : NO
2-132
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
ACTION
DISPLAY
1. Press Transfer button and enter 419.
Display shows first BRI channel:
[725] BRI-TRK
2. Dial BRI trunk number.(e.g., 727)
OR
Press Volume button to select BRI trunk and
Press Right Soft button.
[727] BRI-TRK
3. Select option item.
OR
Press Volume button to select option item and
Press Right Soft button.
[727] BRI-TRK
CHANNEL ANY:YES
CHANNEL ANY:YES
CHANNEL ANY:NO
[727] BRI-TRK
BRI MODE:P-M MSN
[727] BRI-TRK
DLSEND
:OVERLAP
[727] BRI-TRK
CLIP TABLE :NONE
[727] BRI-TRK
NB TYPE:UNKNOWN
4. Select option.
OR
Press Volume button to select BRI station and
press Right Soft button.
[727] BRI-TRK
5. Dial BRI station number.(e.g., 729)
OR
Press Volume button to select BRI station and
press Right Soft button.
[729] BRI-STN
6. Select option item.
OR
Press Volume button to select BRI station and
press Right Soft button.
[729] BRI-STN
CLIP TABLE:1
CHANNEL ANY:YES
CHANNEL ANY:YES
[729] BRI-STN
POWER FEED :NO
7. Select option.
OR
Press Volume button to select option item and
press Right Soft button.
© SAMSUNG Electronics Co., Ltd.
[729] BRI-STN
POWER FEED :YES
2-133
CHAPTER 2. MMC Programming
8. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 323
MMC 405
MMC 418
MMC 421
MMC 423
MMC 714
2-134
CALLING PARTY NUMBER
CO TRUNK NUMBER
CARD RESTART
MSN DIGITS
S/T MODE
DID NAME AND NUMBER TRANSLATION
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[420] PRI OPTIONS
This MMC allows the technician to program a PRI trunk board.
No
Option
0
CHANNEL ANY
Description
When this option is set to YES, the system will place calls on any free
channel of that PRI if the channel chosen by the user is busy. If set to
NO, you will receive a busy signal if they attempt to access a busy
channel even if the other channel on that PRI is free.
1
PRI MODE
PRI access mode select.
NORMAL
Point to Point NORmal. This operates like a standard telephone line with
one CO number per channel and ring according to MMC 406.
DID
Point to Point Direct Inward Dial. This operates in a similar manner to an
analog DID circuit with multiple CO numbers pointed to a single channel
and translated within the system(MMC714) to a single device.
2
3
DLSEND
PRI dial sending mode select.
ENBLOCK
Digits will be collected and sent in a single block similar to a Cell phone.
OVERLAP
Digits will be sent as they are dialled by the user.
CLIP TABLE
Used to select the Calling Party Number to send to the network. In case
of NONE, MMC405 CO TRUNK NUMBER is sent to the network. In
other cases, MMC 323 Calling Party Number entry corresponding with
the selected number is sent to the network.
4
NB TYPE
Used to select the type of the Calling Party Number to send to the
network.
5
UNKNOWN
Unknown number.
INT.NAT
International number.
NATIONAL
National number.
NETWORK
Network specific number.
SUBSCRIB
Subscriber number.
EXTEN
Local number.
ABBREV
Abbreviated number.
NB PLAN
Used to select the type of the Calling Party Number Plan to send to the
network.
UNKNOWN
Unknown numbering plan.
ISDN
ISDN numbering plan(CCITT E.163-164).
DATA
Data numbering plan(CCITT X.121).
TELEX
Telex numbering plan(CCITT F.69).
NATIONAL
National standard numbering plan.
PRIVATE
Private numbering plan.
EXTEN
Local numbering plan.
© SAMSUNG Electronics Co., Ltd.
2-135
CHAPTER 2. MMC Programming
CONDITIONS
Before setting the PRI program, the J2 jumper of the TEPRI board must be set to ‘ON’
for PRI mode.
After changing this program, execute ‘MMC 425 BRI AND PRI CARD RESTART’ to
apply the new setting.
DEFAULT DATA
CHANNEL ANY: YES
PRI MODE: DDI
DLSEND: OVERLAP
CLIP TABLE: NONE
NB TYPE: NATIONAL
NB PLAN: ISDN
ACTION
DISPLAY
1. Press Transfer button and enter 420.
Display shows:
[701] PRI OPTION
2. Dial first PRI trunk number in PRI card.(e.g., 730)
OR
Press Volume button to make selection and
press Right Soft button.
[730] PRI OPTION
3. Enter option number to make selection.
OR
Press Volume button to make selection.
[730] PRI OPTION
4. Press Volume button to make selection.
Then press Right Soft button.
[730] PRI OPTION
CHANNEL ANY:YES
CHANNEL ANY:YES
PRI MODE:DDI
PRI MODE:NORMAL
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 323
MMC 405
MMC 418
MMC 714
2-136
CALLING PARTY NUMBER
CO TRUNK NUMBER
CARD RESTART
DID NAME AND NUMBER TRANSLATION
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[421] MSN DIGIT
Provides a method of assigning an incoming MSN call to a specific station. If any entry in
MSN DIGIT TABLE matches an incoming call’s called party number,
either the specific station is alerted, if it is programmed to accept the call, or the call is
cleared if it is programmed to reject the call.
If the incoming called party number does not have a matching entry in the MSN table,
MMC 406 ringing destination is alerted or the call is released by option.
You can give each MSN number to a specific station and you can select call waiting option:
when a destination is busy, the incoming call must be cleared or camped-on to the
station(which is alerted to the call).
There is a total of eight entries on a trunk basis and each entry consists of the following
fields:
Field
DIGIT
RING 1-6
Description
Digits to be received. There is a maximum of 16 digits
These numbers correspond to the six ring plan destinations for this MSN.
The destinations can be either stations or station groups.
CALL WAIT
Toggles YES or NO: if YES then the call will be camped-on at busy destination
while NO gives busy indication.
OPTION
if Accept then the selected destination party will be alerted. If Reject then the call
will be cleared.
CONDITIONS
A BRI card must be installed in the system. Otherwise, the ‘NO BRI CARD’ message
is displayed.
For each BRI access, two adjacent ports are assigned. You need only change the value
for one of the two ports; the value for the other port will be changed automatically.
DEFAULT DATA
NONE
© SAMSUNG Electronics Co., Ltd.
2-137
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 421.
Display shows:
[701] MSN DGT (1)
2. Enter trunk number.(e.g., 704)
OR
Press Volume button to scroll through ISDN
PORT and press Right Soft button to move cursor.
[704] MSN DGT (1)
3. Enter the location 1-8.(e.g., 4)
OR
Press Volume button to select location and
press Right Soft button to move cursor.
[704] MSN DGT (4)
4. Enter digits to be translated(e.g., 4603881) via
dial keypad and press Right Soft button to move
to the destination selection.(Max. Digit is 12)
[704] MSN DGT (4)
5. Enter destinations for 6 ring plan via dial
Keypad.(e.g., 204 for ring plan 1)
OR
Press Volume button to make selection and
press Right Soft button.
[704] MSN DGT (4)
6. Enter 1 for YES or 0 for NO.
OR
Press Volume button to make selection and
press Right Soft button.
[704] MSN DGT (4)
7. Enter 1 for ACCEPT or 0 for REJECT.
OR
Press Volume button to make selection and
press Right Soft button.
[704] MSN DGT (4)
DGT:
DGT:
DGT:
DGT:4603881
1:204
CW:NO
CW:NO
2:NONE
OPT:ACEPT
OPT:ACEPT
8. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 210
MMC 423
MMC 419
2-138
CUSTOMER ON/OFF PER TENANT
S/T MODE
BRI OPTIONS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[422] TRUNK COS
Used to assign a class of service to each trunk during one of the 6 different ring plans
available. There are 30 different classes of service that are defined in MMC 701 Assign
COS Contents. Classes of service are numbered 01-30. Trunk COS applies on Tandem
connections.
CONDITIONS
NONE
DEFAULT DATA
ALL RING PLANS COS 01
ACTION
DISPLAY
1. Press Transfer button and enter 422.
Display shows first trunk:
[701] TRK COS
2. Dial trunk number.(e.g., 705)
OR
Use Volume button to scroll through trunks.
Press Right Soft button to advance step 3.
OR
Use Volume button to scroll through trunks and
press Left Soft button to advance step 4.
OR
Press ANS/RLS button to select all trunks.
[705] TRK COS
3. Enter day class of service.(e.g., 05)
OR
Use Volume button to scroll through classes of
service and press Right Soft button to advance step 4.
OR
Use Volume button to scroll through classes of
service and press Left Soft button to return to step 2.
[705] TRK COS
© SAMSUNG Electronics Co., Ltd.
1:01
1:01
2:01
2:01
3:01
3:01
[ALL] TRK COS
1:01
1:05
2:01
2:01
3:01
3:01
2-139
CHAPTER 2. MMC Programming
4. Enter the next ring plan class of service.
(e.g., 05)
OR
Use Volume button to scroll through classes of
service and press Right Soft button to return to step 2.
OR
Use Volume button to scroll through classes of
service and press Left Soft button to return to the
previous step.
[705] TRK COS
1:05
2:05
03:01
5. Press Transfer button and enter to save and exit.
OR
Press Speaker button to save and advance to next
MMC.
RELATED ITEMS
MMC 701
MMC 507
2-140
ASSIGN COS CONTENTS
ASSIGN RING PLANS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[423] S/T MODE
Allows the technician to select whether a BRI circuit is a station port or a trunk port.
No
Type
Description
0
TRUNK
The BRI trunk port use ISDN trunk.
1
STATION
The BRI trunk port use for ISDN phone.
CONDITIONS
The BRI card must be installed in the system. Otherwise the ‘NO BRI CARD’ message is
displayed.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 423.
Display shows first BRI:
[725] S/T MODE
2. Dial trunk number.(e.g., 727)
OR
Use Volume button to scroll through BRI numbers
and press Right Soft button to move cursor.
OR
Press ANS/RLS button to select all.
[727] S/T MODE
3. Enter Circuit type.
OR
Press Volume button to select option.
Press Right Soft button to return to step 2.
[727] S/T MODE
TRUNK
TRUNK
[ALL] S/T MODE
TRUNK
STATION
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 418
MMC 419
MMC 421
MMC 424
© SAMSUNG Electronics Co., Ltd.
BRI AND PRI CARD RESTART
BRI OPTION
MSN DIGIT
S0 MAPPING
2-141
CHAPTER 2. MMC Programming
[424] BRI S0 MAPPING
This MMC assigns an ISDN terminal number to a BRI station port.
CONDITIONS
This function can be used only when the BRI card is installed in the system.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 424.
Display shows first terminal number:
[8701]S0 MAPPING
2. Dial terminal number.
OR
Press Volume button to make selection of
terminal numbers and press Right Soft button
to advance cursor.
[8704]S0 MAPPING
3. Dial BRI port number.
OR
Use Volume button to scroll through ports.
Press Right Soft button to return to step 2.
[8704]S0 MAPPING
NONE
NONE
712
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 419
MMC 423
2-142
BRI OPTION
S/T MODE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[425] ASSIGN CALLER ID TRUNKS
Allows the system administrator or technician to activate analog loop trunk Caller ID on a
per-trunk basis. Activating Caller ID will delay the incoming ring indication at the operator
by two ring cycles to allow for the collection of the calling party data.
Each trunk has the following options:
No
Option
Description
0
NORMAL
This is not a Caller ID trunk.
1
CID TRUNK
This is a Caller ID trunk.
Bellcore type data
Supports Bellcore type data only for Caller ID, others type will not supports.
Available in Australia, Israel and Italy only.
CONDITIONS
Before setting CID display, check if the RCM or RCM2 option card is mounted on the
MCP card of the OfficeServ 500 system.
The trunk line must be that of a phone service provider that provides CID.
DEFAULT DATA
ALL TRUNKS: NORMAL
ACTION
DISPLAY
1. Press Transfer button and enter 425.
Display shows:
[701] CID TRUNKS
2. Dial trunk number.(e.g., 705)
OR
Press Volume button to select trunk and press
Right Soft button to move cursor.
OR
Press ANS/RLS button to select all.
[705] CID TRUNKS
3. Dial 0, 1 or 2 to change options.
OR
[705] CID TRUNKS
Press Volume button to select an option and
press Right Soft button to return to step 2.
© SAMSUNG Electronics Co., Ltd.
NORMAL
NORMAL
[ALL] CID TRUNKS
?
CID TRUNK
[705] CID TRUNKS
CID TRUNK
2-143
CHAPTER 2. MMC Programming
4. Press Transfer button and enter to exit.
OR
Press Speaker button to save and advance to next MMC.
RELATED ITEMS
MMC 501
MMC 728
2-144
SYSTEM TIMERS
CID TRANSLATION TABLE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[426] TRUNK GAIN CONTROL
Allows loss levels to be adjusted on a per trunk basis. There are two adjustments available
in this MMC. ‘TX’ is the transmit level adjustment of the trunk to the station. ‘RX’ is the
receive level adjustment of the station to the trunk. See the Trunk Gain Setting Tables for
level option definitions.
There are four types of adjustments as shown below:
No
Trunk Gain
Description
0
+0.0
No adjustment
1
+1.9
Up 1.9 dB
2
-6.0
Down 6.0 dB
3
-2.5
Down 2.5 dB
CONDITIONS
NONE
DEFAULT DATA
TX: +0.0
RX: +0.0
ACTION
DISPLAY
1. Press Transfer button and enter 426.
Display shows:
[701] TRK GAIN
2. Enter desired trunk number(e.g., 705)
via the dial pad.
OR
Press Volume button to make selection.
Press Right Soft button to move cursor.
[705] TRK GAIN
3. Press Volume button to make selection.
Press Right Soft button to move cursor.
[705] TRK GAIN
4. Press Volume button to make selection.
Press Right Soft button to move cursor
and return to Step 1.
[701] TRK GAIN
5. Press ANS/RLS button to select all.
[ALL] TRK GAIN
© SAMSUNG Electronics Co., Ltd.
RX:+0.0
RX:+0.0
RX:+0.0
RX:+0.0
RX:+0.0
TX:+0.0
TX:+0.0
TX:+0.0
TX:-2.5
TX:+0.0
2-145
CHAPTER 2. MMC Programming
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-146
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[428] ASSIGN TRUNK/TRUNK USE
This MMC is used to allow or restrict trunks from making outgoing calls to each other
within the same system.
CONDITIONS
NONE
DEFAULT DATA
DIAL: YES
ACTION
DISPLAY
1. Press Transfer button and enter 428.
Display shows:
(301) USE (301)
2. Dial the trunk use group number.(e.g., 305)
OR
Press Volume button to selection and press
Right Soft button.
OR
Press ANS/RLS button to select all trunk
use groups.
(305) USE (301)
3. Dial the trunk use group number.(e.g., 304)
OR
Press Volume button to selection and press
Right Soft button.
(305) USE (304)
4. Dial 1 for YES or 0 for NO.
OR
Press Volume button to select YES/NO and
press Right Soft button to move cursor.
(305) USE (304)
DIAL:YES
DIAL:YES
(ALL) USE (301)
DIAL:YES
DIAL:YES
DIAL:NO
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 304
MMC 316
MMC 317
MMC 614
© SAMSUNG Electronics Co., Ltd.
ASSIGN EXTENSION/TRUNK USE
COPY STATION/TRUNK USE
ASSIGN STATION/STATION USE
STATION/TRUNK USE GROUP
2-147
CHAPTER 2. MMC Programming
[433] COST RATE
In this MMC, the TRUNK COST RATE flags are entered for each trunk.
DIAL PLANs are defined in MMC 746 Costing Dial Plan. RATE CALCULATION
TABLES are defined in MMC 747. Each trunk may be defined with up to eight cost rates.
Enter one or more of the eight COST RATES per trunk. If an entry is left blank, no call
costing will be calculated for that particular DIAL PLAN.
Call type 8 is fixed for incoming. Apply a cost rate under type 8 only to a trunk if you want
incoming call costing.
CONDITIONS
NONE
DEFAULT DATA
ALL TRUNKS/ALL DIAL PLANS NO COST RATE ASSIGNED
ACTION
DISPLAY
1. Press Transfer button and enter 433.
Display shows trunk number and Cost Rate
table numbers.
[701]
2. Dial trunk number.(e.g., 705)
OR
Press Volume button to select trunk and press
Right Soft button to move cursor.
OR
Press ANS/RLS button for all.
[705]
3. Press Volume button to move cursor along the line
until the cursor is under the Cost Rate mark.(e.g., 2)
Enter 1 for YES or O for NO and press Right
Soft button to return to step 1.
OR
[701]
CR
CR
CR
:12345678
:00000000
:12345678
:00000000
:12345678
:01000000
4. Press Transfer button and enter to exit.
RELATED ITEMS
MMC 746
MMC 747
2-148
COSTING DIAL PLAN
RATE CALCULATION TABLE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[434] CONNECTION STATUS
This read only MMC will confirm the connection status of stations or trunks.
Display status actually displays the status of a station or trunk at the time requested. If a
conference is in progress with the selected trunk or station the display will show one of the
conference parties and an arrow( ). The technician or system administrator can then
display the next parties in the conference. If a station or trunk is in an idle state the display
will show ‘IDLE’. If the station or trunk selected is not a valid selection the display will
show ‘INVALID DATA’. If the station or trunk is made busy by the CPU the display will
show ‘MADE BUSY’. If the station is in busy state with no other connection, the display
will show ‘BUSY’ only.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
Display trunk connection status
1. Press Transfer button and enter 434.
DISPLAY
DISPLAY STATUS
201
IDLE
2. Enter station or trunk number.
Display show connection status.
DISPLAY STATUS
3. Enter another station or trunk.
OR
Press transfer to exit.
DISPLAY STATUS
Display station connection status
1. Press Transfer button and enter 434.
702
702
227
227
DISPLAY STATUS
201
IDLE
2. Enter station or trunk number.
Display show connection status:
DISPLAY STATUS
3. Enter another station or trunk.
OR
Press transfer to exit.
DISPLAY STATUS
© SAMSUNG Electronics Co., Ltd.
235
235
715
715
2-149
CHAPTER 2. MMC Programming
Display trunk status in conference
1. Press Transfer button and enter 434.
DISPLAY STATUS
201
2. Enter station or trunk number.
Display shows connection status:
DISPLAY STATUS
3. Press Right Soft button to display the next
station or trunks involved.
DISPLAY STATUS
4. Enter another station or trunk.
OR
Press transfer to exit.
DISPLAY STATUS
Display status no connection
1. Press Transfer button and enter 434.
702
702
216
227 ,215
216
702 ,227
DISPLAY STATUS
201
IDLE
2. Enter station or trunk number.
Display show connection status:
DISPLAY STATUS
3. Enter another station or trunk.
OR
Press transfer to exit.
DISPLAY STATUS
Display status no connection
1. Press Transfer button and enter 434.
702
702
NONE
NONE
DISPLAY STATUS
201
IDLE
2. Enter invalid station or trunk number.
Display show INVALID DATA:
DISPLAY STATUS
3. Enter another station or trunk.
OR
Press transfer to exit.
DISPLAY STATUS
Display connection status with invalid trunk or
station number
1. Press Transfer button and enter 434.
INVALID DATA
201
2. Enter invalid station or trunk number.
Display show INVALID DATA:
IDLE
DISPLAY STATUS
201
2-150
IDLE
IDLE
DISPLAY STATUS
INVALID DATA
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
3. Enter another station or trunk.
OR
Press transfer to exit.
Display connection status with trunk or station
number in maintenance busy
1. Press Transfer button and enter 434.
DISPLAY STATUS
201
IDLE
DISPLAY STATUS
201
IDLE
2. Enter station or trunk number.
Display show connection status:
DISPLAY STATUS
3. Enter another station or trunk.
OR
Press transfer to exit.
DISPLAY STATUS
725
725
MADE BUSY
MADE BUSY
RELATED ITEMS
MMC 108
MMC 409
© SAMSUNG Electronics Co., Ltd.
STATION STATUS
TRUNK STATUS
2-151
CHAPTER 2. MMC Programming
[436] TRUNK TMC GAIN
Allows loss levels of TMC for analog trunks to be adjusted on a per trunk basis. There are
two adjustments available in this MMC. ‘TX’ is the transmit level adjustment of the trunk
to the station. ‘RX’ is the receive level adjustment of the station to the trunk.
CONDITIONS
This MMC works with 8TRK card only.
This MMC is not to correct low volume. To be used with the support of Samsung
Electronics Co. local distributor.
DEFAULT DATA
TX: +0 dB
RX: +0 dB
ACTION
DISPLAY
1. Press Transfer button and enter 436.
Display shows:
[701] TMC GAIN
2. Enter desired trunk number(e.g., 705) via
the dial pad.
OR
Press Volume button to make selection.
Press Right Soft button to move cursor.
OR
Press ANS/RLS button to select all.
[705] TMC GAIN
3. Press Volume button to make selection.
Press Right Soft button to move cursor.
[705] TMC GAIN
4. Press Volume button to make selection
Press Right Soft button to move cursor and
return to step 2.
[701] TMC GAIN
RX:+0 dB
RX:+0 dB
TX:+0 dB
TX:+0 dB
[ALL] TMC GAIN
RX:+0 dB
RX:+0 dB
RX:+0 dB
TX:+0 dB
TX:+0 dB
TX:-2 dB
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-152
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[500] SYSTEM-WIDE COUNTERS
Used to set the values of the system counters. The counters are listed below with a brief
description of each.
No
0
Counter
ALARM REM.
Default
5
CNTER
1
AUTO RDL
Description
The number of times that an alarm reminder will ring a
station before cancelling. RANGE = 1-99.
3
COUNTER
The number of times the system will redial an outside
number after the auto redial feature has been activated.
RANGE = 1-99.
2
DISA CALL CNTER
99
Sets the maximum number of intercom calls that can be
made after accessing a DISA line. RANGE = 1-99.
3
DISA LOCK
3
CNTER
Number of attempts the system will allow to incorrectly
access a DISA line before locking out the DISA line.
RANGE = -99
4
NEW CALL
99
COUNTER
Number of times the system will allow a user to signal
New Call on a Trunk line during one call. RANGE = 199.
5
UCDS VISUAL
0
ALARM
Used to set the Visual alarm threshold. It is triggered
when the number of calls waiting to be answered in the
UCD group reaches this value. RANGE = 0-25.
6
UCDS AUDIO
0
ALARM
Used to set the Audio alarm threshold. It is triggered
when the number of calls waiting to be answered in the
UCD group reaches this value. RANGE = 0-25.
7
UCD CS LEVEL 1
0
Provides call wait indication level 1 if number of calls
waiting to be answered in UCD group reaches this
value. RANGE = 0-25.
8
UCD CS LEVEL 2
0
Provides call wait indication level 2 if number of calls
waiting to be answered in UCD group reaches this
value. RANGE = 0-25.
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
© SAMSUNG Electronics Co., Ltd.
2-153
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 500.
Display shows:
ALARM REM.CNTER
2. Enter number from above list.(e.g., 6)
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
UCDS AUDIO ALARM
3. Enter in new value via dial keypad.
If entry is valid, system will return to step 2.
UCDS AUDIO ALARM
05
00
00
02
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-154
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[501] SYSTEM TIMERS
Allows the technician to adjust individual timers as necessary.
TIMER TABLE
Timer Name
AA INT DGT TIME
Default
5
Range Unit
1-25 SEC
Description
When the AA card is installed, this timer
determines the inter digit time for AA call
processing. If this timer expires before valid
digits are received by the AA card, the call will
be routed to the AA invalid digits destination.
AA NO ACT TIME
10
1-25 SEC
When the AA card is installed, this timer
determines the time that the AA card will wait
for a first digit for AA call processing. If this
timer expires before a digit is received, the
call will be routed to the AA no action
destination.
AA TRANS TIME
2
0-25 SEC
After this timer, the system will compare
received digits from AA card with the AA
translation table entry and transfer to the
proper destination.
ALARM TIME
100
0-2500 MIN
This is the time the system alarm key will start
ringing after the alarm key has been silenced.
ALERT TONE TIME
1000
100-
This timer sets the duration of the attention
2500 MSEC
tone preceding a call to a phone in the Voice
Announce or Auto Answer mode. This tone
will also precede a forced Auto Answer call.
ALM REM.INTERVAL
25
1-250 SEC
This timer controls the time length between
ring attempts at a station when alarm
reminder is set.
ALM REM RING OFF
10
1-25 SEC
This timer controls the length of the ring cycle
duration when alarm reminder is set at a
station.
ATT. RECALL TIME
30
0-250 SEC
This is the length of time a transfer recall will
ring at a station before recalling the operator.
AUTO REDIAL INT.
30
1-250 SEC
This timer controls the time between attempts
after RETRY dialling is set on a station.
AUTO REDIAL RLS.
45
1-250 SEC
This timer controls the duration of a Ring No
Answer condition on a retry number dialled
before the auto redial is automatically
cancelled.
© SAMSUNG Electronics Co., Ltd.
2-155
CHAPTER 2. MMC Programming
Timer Name
CALLBACK NO ANS
Default
30
Range Unit
1-250 SEC
Description
This timer controls the time before the callback
is automatically cancelled when a callback
detects Ring No Answer.
CAMP ON RECALL
30
0-250 SEC
This timer controls the duration of time a
camped-on call will stay at a destination before
recalling to the transferring station.
CID MSG RECEIVE
6
1-25 SEC
The amount of time that the system will allow a
valid message from the analog CID trunk.
CID DSP ALLOC TM
500
0-900 MS
The delay time that allocate the CID receiver
after trunk incoming detection
CLI DISPLAY TIME
5
1-25 SEC
The amount of time that the Caller ID
information remains on the phone’s display.
CO CLEAR TIME
30
0-250 SEC
When station hangs up a trunk call, the system
keep the call during this time.
CO CONFIRM TIME
3
0-250 MIN
According to MMC 314 CO CONFIRM type,
the outgoing call will be disconnected after this
timer or the outgoing caller will hear the
confirm tone every this time.
CO-CO
20
1-250 MIN
DISCONNECT
This timer monitors the duration of an
unsupervised conference; when it expires, both
trunks are disconnected.
CONFIRM TONE TM
CRD TONE INT TM
1000
30
100-2500
The tone heard when a feature is activated or
MSEC
deactivated.
0-250 SEC
This is the call record tone interval time. An entry
other than zero will cause a tone to be heard by all
the parties in a recorded conversation. The range
for the tone is 001(every second) to 255(every 255
seconds). A value of 000 means no tone. Requires
SVMi card.
DIAL PASS TIME
3
0-25 SEC
This timer monitors the duration of time before
connecting the transmit of the phone to the
trunk side of an outgoing call.
DISA DISCONNECT
30
1-250 MIN
This timer controls the maximum duration of a
DISA call.
DISA LOCK OUT TM
30
1-250 MIN
This timer controls the duration of time a DISA
call is not allowed to be made after the DISA
error counter has expired(MMC 500).
DISA NOANS DISC.
30
0-250 SEC
This timer controls the duration of time a DISA
call is disconnected by force when called party
does not answer.
2-156
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Timer Name
DISA PASS CHECK
Default
30
Range Unit
1-250 MIN
Description
This timer defines the time period before the
system clears the incorrect passcode counter.
DISPLAY DELAY TM
3
1-250 SEC
This timer controls the duration a display is shown in
the LCD display. This timer also controls the
duration of time that error tone is heard.
DOOR LOCK
500
RELES.
DOOR RING
50
DETECT
DOOR RING OFF TM
30
100-2500
This timer controls the duration of time the
MSEC
door lock relay will be activated.
10-250
This timer controls the duration of time before
MSEC
a call is answered by the door phone.
1-250 SEC
This timer controls the duration of ringing at
the door ring destination before automatically
cancelling.
E-HOLD RECALL TM
45
0-250 SEC
This timer controls the duration of time a call is
held exclusively at a station before recalling.
FIRST DIGIT TIME
10
1-250 SEC
This timer controls how long the system will
wait for dialling to begin before dropping the
dial tone and returning the you to error tone.
HOK FLASH MAX TM
150
20-2500
This timer monitors the duration of a hook
MSEC
switch flash to ensure that the flash is valid
and not a line noise or an accidental
hookswitch bounce LONGEST duration.
HOK FLASH MIN TM
70
20-2500
This timer monitors the duration of a
MSEC
hookswitch flash to ensure that the flash is
valid and not a line noise or an accidental
hookswitch bounce SHORTEST duration.
HOOK OFF TIME
HOOK ON TIME
INQUIRY RELEASE
100
1000
30
20-2500
This timer controls the time before dial tone is
MSEC
sent to a single line station.
20-2500
This timer sets the minimum amount of time that
MSEC
the system will recognize as an SLT hang up.
1-250 SEC
This timer monitors the duration of the
interaction of the Soft button to determine
when to return the LCD back to a normal
status. This timer affects only display phones.
INTER DIGIT TIME
10
1-250 SEC
This timer controls the grace period between
dialling valid digits before dropping the call and
returning you back to error tone.
ISDN INT DGT TM
7
1-15 SEC
This timer controls the grace period between
dialling valid digits and the end of the dialling
string on an ISDN call.
© SAMSUNG Electronics Co., Ltd.
2-157
CHAPTER 2. MMC Programming
Timer Name
KMMC LOCK OUT TM
Default
30
Range Unit
10-250 SEC
Description
This timer controls the grace period between
programming actions while in a programming
session. The timer automatically returns the
system to secure programming status.
LCR ADVANCE TIME
5
1-250 SEC
This timer controls the duration of time
before selecting the next allowable route
when a station is allowed to route
advance.
LCR INTER DIGIT
5
1-250 SEC
This timer controls the grace period between
dialling valid digits before accessing a trunk.
LONG KEY DETECT
600
0-2500 MSEC
This timer controls the time a key must be
held down before the key press is repeated.
LONG KEY REPEAT
300
0-2500 MSEC
This timer controls the time between
repeated digits on a long key press.
MCL DELAY TIME
4
1-8 SEC
When outgoing call routes the MCL line,
dialling will be paused during this timer.
Available in U.K. only.
MS LED ON TIME
10
1-10 SEC
This timer controls the duration a
Manual
Signaling key will remain on after use.
OFF HOOK RING INT
15
1-250 SEC
This timer controls the duration of time
between ring bursts to a user who has a
camped-on call.
OHVA ANSWER TIME
10
1-250 SEC
This timer controls the time duration of an
OHVA call before automatic rejection.
PAGE TIME OUT
20
1-250 SEC
This timer controls the duration of a page
announcement.
PAGE TONE TIME
500
100-2500
This timer controls the duration of tone
MSEC
burst heard over the page prior to the
page announcement.
PARK RECALL TIME
45
0-250 SEC
This timer controls the duration of time a
call is parked before recalling to the call
park originator.
PC-MMC LOCK TIME
5
1-60 MIN
This timer monitors the PCMMC activity,
drops the link if no action is created by
PCMMC and returns the system back to
secure program status.
PERI UCD REPORT
5
3-99 SEC
This timer is the interval that a periodic
UCD report is provided to an SIO port.
POWER DOWN TIME
2-158
2000
500-9900
This timer monitors the power to the ROM
MSEC
pack to begin shutdown status.
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Timer Name
RECALL
Default
2
Range Unit
1-250 MIN
DISCONNECT
RECALL WAIT TIME
Description
This is the time an attendant recall will ring
before being disconnected.
15
0-250 SEC
This is the time any recall(hold or transfer)
continues to recall at your station before it
recalls to the operator.
ROUTE OPTIMIZE
5
0-250 SEC
When the call is made via Q-SIG signaling, the
route optimization is activated after this time.
SMDR START/DP
30
1-250 SEC
This grace period timer starts SMDR
recording for rotary
SMDR START/DTMF
15
1-250 SEC
This grace period timer starts SMDR
recording for touchtone dialling. This timer
also controls the LCD duration timer on the
phones. The duration time displayed and the
SMDR time duration will be the same.
SYS HOLD RECALL
45
0-250 SEC
This timer determines the time calls can be
left on hold before recalling back to the
holding station. This is a system-wide
timer. Setting timer to 000 will defeat this
feature and no recalling will take place.
TRANSFER RECALL
20
0-250 SEC
This timer determines the time transferred
calls ring before recalling. This is a
system-wide timer.
TSW CONN. DELAY
0
0-10 SEC
When incoming trunk makes outgoing call
to another trunk, the system connects
voice path after this time.
UCDS AUDIO ALARM
0
0-990 SEC
When an AA card is installed and the digital
UCD package enabled, this counter
determines the maximum number of seconds
a call has been waiting at the UCD group
before the UCD group’s SUPV key begins to
flash along with an audio alarm. For more
UCD alarm conditions, see MMC 500.
UCDS VISUAL ALAM
0
0-990 SEC
When an AA card is installed and the
digital UCD package enabled, this counter
determines the maximum number of
seconds a call at the UCD group before
the UCD group’s SUPV key begins to flash
as an alarm. For more UCD alarm
conditions, see MMC 500.
© SAMSUNG Electronics Co., Ltd.
2-159
CHAPTER 2. MMC Programming
Timer Name
VMS UCD MSG TIME
Default
5
Range Unit
1-99 SEC
Description
When this timer expired, the call return to
idle member. Requires SVM-800.
VOICE DIAL DELAY
8
5-15 SEC
This timer monitors the duration of
interaction between main software and
Voice Dialler. If there is no response from
Voice Dial card within this time, the system
decide the voice dialling is fail.
VOIP RE-ROUTE TM
5
2-25 SEC
When the outgoing call is made via VOIP
trunk and does not receive ack message
from called party within this time, the call is
treated as fail.
When the value is ‘0
Certain timers are disabled when the value is ‘0 .
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
SOME TIMERS ARE DEPEND ON COUNTRY
ACTION
DISPLAY
1. Press Transfer button and enter 501.
Display shows first timer value:
AA INT DGT TIME
2. Press Volume button to select timer and press
Right Soft button to move cursor.
KMMC LOCK OUT TM
3. Enter new value using keypad; if valid, system
returns to step 2 with new value.
KMMC LOCK OUT TM
05 SEC
060 SEC
060 SEC 250
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-160
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[502] STATION-WIDE TIMERS
Allows certain station timer values to be changed on a per-station basis or for all stations.
No
0
Item
NO ANS FWD
Description
This timer controls how long the station will ring before Forward on No
Answer takes place.(1250 sec)
1
DTMF DUR.
This timer governs the duration of DTMF digits which are transmitted to
an external VMS system port. This can be used when a VMS system
fails to recognize the default DTMF digit duration being transmitted from
the SLT port.(1009900 ms)
2
FDGT DELY
This timer will be valuable for the system administrator to insert a suitable
delay before generating DTMF digits for In Band integration.(1009900 ms)
3
OFFHK SEL.
This timer controls the grace period before placing an internal/external
call as programmed in MMC 306.(0250 sec)
4
EFWD DELAY
This timer controls the External Call Forward
feature which will allow a
station to ring before the call is placed on external call forwarding.
(1250 sec)
5
CC RNG DLY
When the station does not answer incoming call within this time, the
other stations with CC key of that station will be ringing together. This
feature only applies to the station call and station group call does not
serviced.(10 sec)
CONDITIONS
NONE
DEFAULT DATA
NO ANS FWD: 015 SEC
DTMF DUR: 100 MSEC
F-DGT DELY: 600 MSEC
OFFHK SEL: 015 SEC
EFWD DELAY: 010 SEC
CC RNG DLY: 010 SEC
© SAMSUNG Electronics Co., Ltd.
2-161
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 502.
Display shows:
[201] NO ANS FWD
2. Dial station number.(e.g., 205)
OR
Press Volume button to select station and
press Right Soft button.
OR
Press ANS/RLS button to select all stations and
press Right Soft button.
[205] NO ANS FWD
3. Enter new value(must be three digits) via
dial keypad.(e.g., 020)
System will return to step 2.
[205] NO ANS FWD
4. Dial timer number from above list.(e.g., 1)
OR
Press Volume button to select and press
Right Soft button to move cursor.
[205] DTMF DUR.
5. Enter new timer value.(must be four digits,
e.g., 0200)
System returns back to step 2.
[205] DTMP DUR.
015 SEC
015 SEC _
[ALL] NO ANS FWD
015 SEC _
015 SEC 020
0100 MS
0100 MS
_
0200
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 102
MMC 207
MMC 306
MMC 726
2-162
CALL FORWARD
ASSIGN VM/AA PORT
HOT LINE/OFF HOOK SELECTION
VM/AA OPTIONS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[503] TRUNK-WIDE TIMER
Allows certain trunk timer values to be changed on a per-trunk basis or for all trunks. It is
not advisable to change these values, with the exception of trunk Flash Time, without
assistance from Technical Support.
No
Item
Description
Range
00
ANS.BAK TM
ANSWER BACK TIME. This timer is used for certain
types of E & M signaling and does not affect normal
CO lines.
0-2500 MSEC
01
CLEARING
This timer ensures that a call is fully disconnected at
the CO by preventing CO access outgoing or
receiving incoming ring between a disconnect and
the expiration of this timer.
100-9900 MSEC
02
CO SUPV TM
CO SUPERVISION TIME. this is the minimum
length of loop open disconnect received from the
CO that will be seen as a valid hang up on the
system.
10-2500 MSEC
03
DTMF DUR.
DTMF DURATION. This is the length of the DTMF
digits that will be sent to the CO on this line.
100-9900 MSEC
04
F-DGT DELY
First-DIGIT DELAY. This is the length of time the
system will wait for CO line conditions to stabilize
after seizure before sending DTMF digits.
100-9900 MSEC
05
FLASH TIME
This is the duration of the momentary open sent on
a circuit when FLASH key is pressed.
20-2500 MSEC
06
NO RING TM
This is the length of time the system will wait after
detecting a ring burst on a line before deciding the
call has disconnected.
1-25 SEC
07
PAUSE TIME
This is the length of time the system will wait before
sending the next digit for a pause in a speed dial
bin.
1-25 SEC
08
PRS DET TM
This means the duration of PRS signal pulse. If the
PRS signal is reversed when opposite party is
answered and maintain the status before the
opposite party disconnect the call, the PRS DET TM
must be set to 0.
0-2500 MSEC
09
RNG DET TM
RING DETECT TIME. This is the minimum length of
ring signal the system will regard as a valid ring.
10-2500 MSEC
10
WINK TIME
This is the duration of the acknowledgment signal
that the system will send on an E & M circuit
100-300 MSEC
11
MF/DP INT
This is the interval between sending digit. In case of
DTMF signal, over the 500ms will be serviced as
100 ms.
100-9900 MSEC
12
MFR DLY TM
This is a delay time to allocate the MFR after
incoming trunk is detected. This is to prevent the
wrong detection of DTMF signal by noise.
0-25 SEC
© SAMSUNG Electronics Co., Ltd.
2-163
CHAPTER 2. MMC Programming
CONDITIONS
NONE
DEFAULT DATA
ANS.BAK TM: 0600 MSEC
CLEARING: 1000 MSEC
CO SUPV TM: 2500 MSEC
DTMF DUR.: 0100 MSEC
F-DGT DELY: 0600 MSEC
FLASH TIME: 0600 MSEC
NO RING TM: 04 SEC
PAUSE TIME: 03 SEC
PRS DET TM: 0000 MSEC
RNG DET TM: 0350 MSEC
WINK TIME: 200 MSEC
MF/DP INT: 0700 MSEC
MFR DLY TIME: 00 SEC
ACTION
DISPLAY
1. Press Transfer button and enter 503.
Display shows:
[701] ANS.BAK TM
2. Dial trunk number.(e.g., 704)
OR
Press Volume button to select trunk and press
Right Soft button to move cursor.
OR
Press ANS/RLS button to select all trunks.
[704] ANS.BAK TM
3. Dial timer number from the list.
OR
Press Volume button to select timer and press
Right Soft button to move cursor.
[704] DTMF DUR.
4. Enter new timer value.
(must be four digits, e.g., 0200)
System returns to step 2.
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
[704] DTMF DUR.
0600 MS
0600 MS
[ALL] ANS.BAK TM
0600 MS
0100 MS
_
_
0100 MS 0200
RELATED ITEMS
NONE
2-164
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[504] PULSE MAKE/BREAK RATIO
Allows the ability to change the value of pulses per second and the duration of the
make/break time. This will only affect rotary dial trunks.
No
Item
Description
0
MAKE/BREAK RATIO
Make/Break ratio of dial pulse(01-99)
1
PLUS PER SECOND
Number of dial pulses per second(10 or 20)
CONDITIONS
NONE
DEFAULT DATA
MAKE/BREAK: 33 MAKE
PULSES PER SECOND: 10 PPS
ACTION
DISPLAY
1. Press Transfer button and enter 504.
Display shows:
MAKE/BREAK RATIO
2. Dial 0 or 1 for option.
OR
Press Volume button for selection and press
Right Soft button to move cursor.
PULSE PER SECOND
3. Dial new value.
System returns to step 2.
PULSE PER SECOND
33 MAKE
10 PPS _
10 PPS 20
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 402
© SAMSUNG Electronics Co., Ltd.
TRUNK DIAL TYPE
2-165
CHAPTER 2. MMC Programming
[505] ASSIGN DATE AND TIME
Allows the system date and time to be set. This will set the system-wide clock.
Type
Description
Range
YY
Year
00-99
MM
Month
01-12
DD
Date
01-31
W
Day
0-6(0: SUN, 1: MON, 2: TUE, 3: WED, 4: THU, 5: FRI, 6: SAT)
HH
Hour
00-23
MM
Minute
00-59
CONDITIONS
NONE
DEFAULT DATA
FOLLOW SOFTWARE DATE 12:00
ACTION
DISPLAY
1. Press Transfer button and enter 505.
Display shows:
OLD:0111095:0901
2. Enter new time and date using above table
System returns to step 2.
OLD:0111095:0901
3. Verify time and date.
Re-enter if necessary.
OLD:0111121:1445
NEW:YYMMDDW:HHMM
NEW:0111121:1445
NEW:YYMMDDW:HHMM
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 861
2-166
SYSTEM OPTIONS: AUTO UPDATE TIME
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[506] TONE CADENCE
Provides the ability to customize the tone cadence on a system-wide basis.
The system can provide eleven types of tone and three types of tones provided from
Central Office or PBX system can be detected. Please call Technical Support before
changing any cadences as some systems may require default settings.
No
Item
00
BUSY TONE
01
CONFM/BARGE
Description
The called station is busy.
A feature has been successfully activated/cleared or a Barge In
with Tone has been performed.
02
DIAL TONE
The system is ready to interpret key presses/dialled digits.
03
DND/NO MORE
The called station is in DND or has no free CALL buttons.
04
ERROR TONE
An error has been made.
05
HOLD/CAMPON
This is the system generated hold tone.
06
MSGWAT TONE
This is the tone heard at an SLT with a message waiting.
07
RGBACK TONE
The called station is ringing.
08
RING TONE
This is the tone heard from ROP device or Loud Bell when these
devices are called.
09
TRANSFERER TONE
This is the tone heard when the transfer button is pressed or an
SLT hook flashes.
10
DID RNGBACK
This is the tone heard by the outside party when they dial a DID
number.
11
CO BUSY TONE
This is used to detect the busy tone provided from Central Office or
PBX system.
12
CO RINGBACK
This is used to detect the ring back tone provided from Central
Office or PBX system.
13
CO DIAL
This is used to detect the dial tone provided from Central Office or
PBX system.
CONDITIONS
NONE
© SAMSUNG Electronics Co., Ltd.
2-167
CHAPTER 2. MMC Programming
DEFAULT DATA
TONE
ON
OFF
ON
OFF
BUSY TONE
350
350
350
350
CONFIRM/BARGE-IN
250
250
250
1250
DIAL TONE
CONTINUOUS
DND/NO MORE TONE
250
250
250
250
ERROR TONE
200
200
200
200
HOLD/CAMP-ON TONE
500
3500
500
3500
MESSAGE WAIT TONE
1000
250
1000
250
RING BACK TONE
1000
4000
1000
4000
RING TONE
1000
2000
1000
2000
100
100
100
100
1000
2000
1000
2000
350
350
350
350
1000
4000
1000
4000
TRANSFER TONE
DID RINGBACK TONE
CO BUSY TONE
CO RINGBACK TONE
CO DIAL TONE
CONTINUOUS
ACTION
2-168
DISPLAY
1. Press Transfer button and enter 506.
Display shows:
BUSY TONE
INTERRUPT TONE
2. Dial tone number from above list.(00-13, e.g., 09)
OR
Press Volume button to select tone, press
Left Soft button and advance to step 3.
TRANSFERER TONE
INTERRUPT TONE
3. Dial tone option 0 for CONTINUOUS or
1 for INTERRUPT.
OR
Press Volume button to select tone control and
press Right Soft button to advance step 4.
OR
Press Left Soft button to return to step 2.
TRANSFERER TONE
INTERRUPT TONE
4. Dial new value for interrupt times.
(must be four digits)
Press Right Soft button advances cursor.
Press Left Soft button retreats cursor.
If valid entry, system returns to step 2.
TRANSFERER TONE:0100
9900 0100 9900
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
All times are in milliseconds.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-169
CHAPTER 2. MMC Programming
[507] ASSIGN RING PLAN TIME
Use this MMC to program Ring Plans time settings. Ring Plans provide six separate
ringing destinations based on day of the week and time of day. The start time within a plan
is the time the system will switch from one ringing destination to the next. The end time is
the time the system will switch from that plan to the previous plan.
A RPO(Ring Plan Override) key is not needed as the system will switch automatically;
however, it is helpful to have a dedicated button so the status can be manually changed if
needed. If a ring plan has no time entry the ring plan defaults to ring plan 1. The ring plans
correlate with all MMC’s that program ring or termination destinations and station and
trunk COS.
Use the following example of assigning Ring Plans:
RING PLAN
Start Time
End Time
(MON: 1)
ST: 0000
END: 23:59
(MON: 2)
ST: 0800
END: 2200
(MON: 3)
ST: 1000
END: 2000
(MON: 4)
ST: 1200
END: 1800
(MON: 5)
ST: 1300
END: 1600
(MON: 6)
ST: 1400
END: 1500
Using a 24 hour clock in the example above notice that the END time is within the same 24
hour period. The system will stay in the last active Ring Plan from the previous day until
the end time which is 23:59. Monday starts the Ring Plan 1 at 00:00. The system will stay
Ring Plan 1 until 08:00 and will stay in Ring Plan 2 until Ring Plan 3 starts. As each ring
Plan start it will override the previous Ring Plan.
If a Ring Plan ends and there are no additional Ring Plans the system will default to the
Ring Plan with time that extends past the expired ring plan time.
CONDITIONS
When using a Samsung Built in Voice Mail Card that only has day/night mode, the
day/night must be set for each RING PLAN at ‘MMC 758 VM DAY/NIGHT’.
Ring Plans must be programmed in sequence. IE. RP 1, 2, 3, 4 etc.
A Ring Plan cannot be omitted. IE. RP 1, 2, 5 etc.
A higher numbered Ring Plan cannot have a START time before a lower numbered
Ring Plan
Ring Plan 1
Ring Plan 1 is the default Ring Plan of each day. If no Ring Plan destination is
input the operator group is the default destination.
2-170
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
DEFAULT DATA
START: NONE
END: NONE
ACTION
DISPLAY
1. Press Transfer button and enter 507.
Display shows:
RING PLAN (SUN:1)
2. Dial day number.(0-6, e.g., 3)
OR
Press Volume button to select day.
Press Right Soft button to advance cursor to step 3.
RING PLAN (WED:1)
3. Dial ring plan number.(1-6, e.g., 2)
OR
Press Volume button to select day.
Press Right Soft button to advance cursor to step 4.
RING PLAN (WED:2)
4. Dial start time.(e.g., 1030)
If valid, cursor moves to end time.
Enter end time.
If valid, system returns to step 2.
Begin again.
RING PLAN (WED:1)
ST:
ST:
ST:_
END:
END:
END:
ST:1030 END:1800
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 202
MMC 512
MMC 701
MMC 722
MMC 723
© SAMSUNG Electronics Co., Ltd.
FEATURE PASSCODE
HOLIDAY ASSIGNMENTS
STATION COS
STATION KEY PROGRAMMING
SYSTEM KEY PROGRAMMING
2-171
CHAPTER 2. MMC Programming
[508] CALL COST
Allows the system administrator to set the Call Cost attributes generated by the system
during a call. This information can be displayed on the phone LCD during a call or as an
SMDR record.
No
Item
Description
0
UNIT COST PER MP
When the system is installed to receive MP on a C. O. outgoing
call. It is used for generating total call cost by multiplying it by the
number of pulses. Allows a maximum value of 9999.
1
CALL COST RATE
This generates additional call cost calculated by multiplying this
rate by the original call cost. Ranges from 100 through 255.
CALL COST
Changing this value when there is a call in progress may result in an inaccurate
call cost. This MPD facility requires the Meter Pulse Detection version of the trunk
card.
CONDITIONS
NONE
DEFAULT DATA
UNIT COST PER MP 100 PERCENT
CALL COST RATE 100 PERCENT
ACTION
DISPLAY
1. Press Transfer button and enter 508.
Display shows:
UNIT COST PER MP
2. Dial 0 OR 1.(e.g., 1)
OR
Press Volume button to select , and press
Right Soft button to move cursor.
CALL COST RATE
3. Enter new value.(e.g., 110 for 110 percent)
System returns to step 2.
CALL COST RATE
0100PESET
100 %
110 %
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 110
2-172
STATION ON/OFF: CALL COST OPTION
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[510] SLI RING CADENCE
Provides the ability to customize the ring cadence for single line ports on a system-wide
basis. There are 5 cadences available. Please call Technical Support before changing any
cadences as some peripheral systems may require default settings.
No
Item
Description
1
STN RING
This is the cadence intercom calls will ring at.
2
TRK RING
This is the cadence trunk calls will ring at.
3
DOOR RING
This is the cadence doorphone calls will ring at.
4
ALM RING
This is the cadence alarm reminder calls will ring at.
5
CBK RING
This is the cadence callbacks will ring at.
CONDITIONS
NONE
DEFAULT DATA
(a unit: milliseconds)
Item
ON
OFF
ON
OFF
STN RING
1000
3000
1000
3000
TRK RING
0400
0200
0400
2000
DOOR RING
0400
0100
0400
2000
ALM RING
0400
0200
0400
3000
CBK RING
1000
4000
1000
4000
ACTION
DISPLAY
1. Press Transfer button and enter 510.
Display shows:
1:STN RING:0400
2. Dial cadence number from above list.(e.g., 3)
OR
Press Volume button to select , press
Left Soft button and advance to step 3.
3:DOOR RING:0400
3. Dial new value for interrupt times.
(must be four digits)
Press Right Soft button advances cursor.
Press Left Soft button retreats cursor.
If valid entry, system returns to step 2.
3:DOOR RING:0100
© SAMSUNG Electronics Co., Ltd.
0200 0400 3000
0100 0400 2000
9900 0100 9900
2-173
CHAPTER 2. MMC Programming
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-174
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[511] MSG WAITING LAMP CADENCE
This MMC defines the cadence(flash rate) of single line telephone message waiting lamps
on phones connected to an MWSLI supported card. There are two main choices for the
MW lamp cadence available, these being continuous and interrupted as described below.
No
Item
0
INTERRUPTED
Description
The MW lamp will flash at a rate determined by the timer settings.
The shortest on time is 100 ms and the longest on time is 3000 ms.
The timer is adjusted in 100 ms increments.
1
CONTINUOUS
When an MWSLI port has a message, the lamp will be lit steady.
CONDITIONS
MWSLI SUPPORTED CARDS ONLY
DEFAULT DATA
INTERRUPT LED: 1000 MS-ON 1000 MS-OFF
ACTION
DISPLAY
1. Press Transfer button and enter 511.
Display shows:
MW LAMP CADENCE
2. Press 0 or 1 to select CADENCE.
OR
Press Volume button to make selection.
Press Right Soft button to advance step 3.
MW LAMP CADENCE
3. Dial new values for interrupt times.(four digits)
MW LAMP CADENCE
Press Right Soft button to move cursor back.
If valid entry, system returns to step 2.
Press Left Soft button to move cursor back.
If valid entry, system returns to step 2.
INTERRUPT LED
INTERRUPT LED
2000 2000
4. Press Transfer button and enter to exit.
OR
Press Speaker button to save and advance to next MMC.
RELATED ITEMS
MWSLI SUPPORTED CARDS ONLY
© SAMSUNG Electronics Co., Ltd.
2-175
CHAPTER 2. MMC Programming
[512] HOLIDAY ASSIGNMENT
This MMC defines up to 60 holiday dates throughout the year. The system will override the
normal ring plan for these days and remain in the ring plan associated with the holiday.
Dates are entered in a month day format. For example July 4th would be 0704. One ring
plan applies to all holidays.
CONDITIONS
NONE
DEFAULT DATA
NO HOLIDAY ASSIGNED
FOLLOW RING PLAN 1
ACTION
DISPLAY
1. Press Transfer button and enter 512.
Display shows the Ring Plan:
RING PLAN
2. Press Right Soft button advance cursor.
Press Volume button to select a Ring Plan.
OR
Use the dial pad to select a Ring Plan.(e.g., 2)
RING PLAN
3. Press Right Soft button to enter and advance cursor.
RING PLAN
4. Press Volume button to scroll to Assign Holiday
and press Right Soft button to advance cursor.
ASSIGN HOLIDAY
5. Press Volume button to select entry and press
Right Soft button enter and advance cursor.
ASSIGN HOLIDAY
6. Dial date using the dial pad for holiday.(e.g., 0704)
ASSIGN HOLIDAY
FOLLOW 1
FOLLOW 2
FOLLOW 2
01:
05:
05:0704
7. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 507
2-176
ASSIGN RING PLAN TIME
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[513] HOTEL TIMER
This MMC is where the check out time for guest rooms and the room clean timers are set.
These are system wide timers that affects all rooms.
No
0
Item
CHECK OUT TIME
Description
If a room is occupied during the checkout time an additional days
room charge will be automatically added to the room bill. If a
room is flagged as Occupied and HOLD then the additional days
room charge will not be added. Setting a room status to hold is
how a late check out can be performed.
1
ROOM CLEAN TIME
This is the time each day that the system will flag all occupied
rooms as NEEDS CLEANING.
2
CHECK IN END TM
This time is used to decide an additional days room charge will be
automatically added to the room bill when the first check out time is
reached after check-in.
CONDITIONS
This function can be used only when the hotel function is enabled at ‘MMC 813 HOTEL
OPERATION’.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 513.
Display shows:
CHECK OUT TIME
2. Select the timer using the Volume buttons.
ROOM CLEAN TIME
3. Enter new time using above 24 hour clock
system returns to step 2.
ROOM CLEAN TIME
HH:MM :
HH:MM :
:
:
HH:MM : 11:30
4. Press Transfer button and enter to exit.
OR
Press Speaker button to save and advance to next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-177
CHAPTER 2. MMC Programming
[514] TONE SOURCE
This program is assigned external tone source instead of system tone. There are 7 types of
tone for external tone source.
No
Type
0
BUSY TONE
1
DIAL TONE
2
DND/NO MORE
3
TRANSFER TONE
4
MSGWAIT TONE
5
ERROR TONE
6
RINGBACK TONE
CONDITIONS
NONE
DEFAULT DATA
TONE
ACTION
DISPLAY
1. Press Transfer button and enter 514.
Display shows:
BUSY TONE
2. Enter the system tone number.(0-6)
OR
Press Volume button to select tone number and
press Right Soft button to move cursor.
DIAL TONE
3. Dial a number for external tone source.
OR
Press Volume button to select tone number and
press Right Soft button to store.
DIAL TONE
TONE
TONE
372
4. Press Transfer button and enter to exit.
OR
Press Speaker button to save and advance to next MMC.
RELATED ITEMS
NONE
2-178
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[515] ASSIGN DAYLIGHT SAVING DATE
Allows the Technician to program the start dates and end dates of daylight saving time on a
system for the current year and the next 9 years. System will automatically add 1 hour to
the system clock at 02.00(2.00 a.m.) on the Start date and subtract 1 hour from the system
clock at 02.00(2.00 a.m.) on the End date.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 515.
Display shows:
NO:YY:START:END
2. Enter entry number.(e.g., 01 for current year)
OR
Press Volume button to select entry number and
press Right Soft button to move cursor.
NO:YY:START:END
3. Enter year.(e.g., 03 for 2003)
OR
Press Volume button to select year and press
Right Soft button to move cursor.
NO:YY:START:END
4. Enter the start date in format MMDD.
(e.g., 30th March would be 0330)
NO:YY:START:END
5. Enter the start date in format MMDD.
(e.g., 26th October would be 1026)
NO:YY:START:END
01:
01:
:
:
00:03:
:
:
:
00:03:0330 :
00:03:0330 :1026
6. Press Transfer button and enter to exit.
OR
Press Speaker button to save and advance to next MMC.
RELATED ITEMS
MMC 505
MMC 861
© SAMSUNG Electronics Co., Ltd.
DATE AND TIME
SYSTEM OPTIONS: AUTO UPDATE TIME
2-179
CHAPTER 2. MMC Programming
[600] ASSIGN OPERATOR GROUP
Used to assign an operator group for each ring plan.
CONDITIONS
NONE
DEFAULT DATA
RING PLAN 1~6: 500
ACTION
1.
DISPLAY
Press Transfer button and enter 600.
Display shows:
OPERATOR GROUP
1:500
2:500
2. Dial the ring plan number.(1~6)
OR
Press Right Soft button to advance the cursor.
OPERATOR GROUP
3. Dial the group number.
OR
Press Volume button to select group and press
Right Soft button.
OPERATOR GROUP
1:500
1:501
2:500
2:500
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 211
MMC 406
MMC 601
2-180
DOOR RING ASSIGNMENT
TRUNK RINGING ASSIGNMENT
ASSIGN STATION GROUP
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[601] ASSIGN STATION GROUP
This MMC is used to build all station groups. There are 40 programmable groups available
in a M system and 80 for a L system.
The options for setting up these groups are as follows:
No
0
Option
TYPE
Description
This is the type of group you are creating and can be one of the
following:
0
NORMAL: Used to assign stations in a ring group. The members can
1
VMAA: Used to group a number of voice mail port extensions. These
be stations, common bell contacts or Ring over Page relays.
must have been defined in MMC 207 as VMAA ports or they cannot
be entered here. Check all programming I n MMC 726 to ensure that
the In band DTMF codes are properly set.
2
UCD: Used to build a UCD group. The system will support two
methods of UCD:
- TYPE 1 UCD
The group OVERFLOW/N-ANS destination(see below) is defined as
an SLT port to which you must connect some type of announcement
device to play to callers while they are on hold.
Please note that this type of UCD group has the following limitations.
a)
The announcement device must be able to terminate the
announcement with a hook flash and a transfer back to the UCD
group.
b)
Only one caller at a time can hear the announcement.
c)
Each caller connected to the announcement must hear the
d)
It is possible that a new caller may ‘jump ahead’ in the queue if a
announcement in its entirety.
previous caller is currently connected to the announcement
device.
- TYPE 2 UCD
The group OVERFLOW/N-ANS destination(see below) is defined as
an AA port or group. This will only work if an AA card has been
installed in the system.
The digital announcer in the AA card will supply two recorded
announcements to callers in queue. The first announcement is
played only once, the second announcement will repeat for as long
as the caller is in queue.
This type of UCD group has the following advantages:
a)
No external device need be installed to provide an
b)
Multiple callers can hear the announcement(s) simultaneously.
announcement.
© SAMSUNG Electronics Co., Ltd.
2-181
CHAPTER 2. MMC Programming
No
0
Option
Description
TYPE
c)
Callers hearing the announcement will be transferred to a free
UCD group member(agent) as soon as the agent becomes
available.
d)
The callers place in queue is always maintained.
Additional programming for this type of UCD group is in MMC
607. There is a maximum of 20 UCD groups available on a
system due to availability of system resources.
3
AA: This is used to group a number of AA ports. An Auto
Attendant(AA) card must be installed in the system to do this.
4
BI-VMS: This is the voice mail group for the Built-In Voice Mail Card.
When a Built-In Voice Mail Card is installed, group 529 must be
programmed as a BI-VMS group on a M system and group 549 must
be used for a L system. Group 529(or 549) are fixed for BI-VMS use.
If BI-VMS is not installed in the system, group 529(or 549) can be
used as any other group can be used.
5
MESSAGE: Used to group a number of extensions to serve as a
message desk or message group. When one of the stations in this
type of group leaves a message to another station the messaged
station will return the message to the message group so any
member can answer the call. If a station is a member of more than
one message group, then any message indications made by that
station would be for the first numerical message group they are a
member of. It is not recommended to program stations in to multiple
station groups.
6
S0 STN GRP: This is used to group a number of S0 station for video
conference.
1
RING MODE
Each group can have one of the following ring modes. This will decide
how calls are placed to the group.
0
SEQUENTIAL: The stations listed as ‘members’(see below) will be
called on a first available basis. Calls will first go to the first member,
if the first member is busy, calls will go to the second member, if the
second member is busy, calls will go to the third member etc. This
type of group is useful for placing the bulk of the incoming calls to a
selected individual, with other members only getting the calls when
the first member is busy. The number of members allowed for a
sequential group is 48.
1
DISTRIBUTED: The first call will go to the first member, the second
call will go to the second member, the third call will go to the third
member. This type of group is useful for evenly distributing the call
among all group members. The number of members allowed for a
distributed group is 48.
2-182
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
No
1
Option
RING MODE
Description
2
UNCONDITIONAL: Calls are placed to all group members
simultaneously.
This reduces the number of members of the groups to 32. If a group
member is busy, they can receive off hook ring if defined in MMC
300. This ring mode option is not available for UCD or VMAA groups.
The SGR INC BUSY option is not available for unconditional ring
mode.
2
OVERFLOW
This is the timer value that will cause unanswered calls to a group to
begin also ringing the NEXT PORT(see below) after this timer has
elapsed. If set to 000, no overflow will take place.
3
GROUP
This is a timer that will determine how long Trunk Line calls transferred
TRANSFER
to the group will ring at the group before recalling. If set to 000, no recall
will take place.
4
NEXT PORT
This is the station or group number that callers will also ring at if the
OVERFLOW feature has been programmed. The OVERFLOW
DESTINATION can be defined as:
1
COMMON BELL There are up to 3 Common bells available on L
system and 1 on M system. Because there is a common bell port on
each MISC card.
2
RING OVER PAGE The ROP port can be defined as the NEXT port.
3
STATION OR STATION GROUP. Any station or station group can be
defined as the NEXT port.
5
MEMBER
List all members that are to be in the group. Up to 48 members for the
system are allowed in each group, but stations can be assigned to
multiple station groups
6
NEXT HUNT
The length of time a call will ring at a station before it hunts to the next
group member.
7
GROUP BUSY
When this option is set to ON, a busy signal will be sent to the caller if
all group members are busy. When this option is set to OFF, the ring
back tone is sent to the caller even if all group members are busy.
Obviously UCD is an exception to this rule. This option only works when
MMC 210 SGR INC BUSY is set to OFF. When MMC 210 SGR INC
BUSY is set to ON, all station groups will follow this setting.
8
GRP AUTOANS
When this option is set to ON, a group call follows auto answer option
also.
Calls to a group
Calls to a group do not follow the call forwarding instructions of any stations in the
group.
© SAMSUNG Electronics Co., Ltd.
2-183
CHAPTER 2. MMC Programming
CONDITIONS
A station can be assigned to all station groups. A station group can normally
accommodate up to 48 members, but only up to 32 members if the RING MODE is
‘UNCONDITIONAL’.
To enable off-hook ring for calls incoming to busy members, set the OFFHOOK RING
of MMC 300 CUSTOMER ON/OFF PER STATION OFFHOOK RING to ‘ON’.
Even in this case, however, the off-hook ring is enabled only when the RING MODE is
‘UNCONDITIONAL’.
DEFAULT DATA
NORMAL GROUP
ACTION
2-184
DISPLAY
1. Press Transfer button and enter 601.
Display shows:
[501] STN.GROUP
2. Dial group number.(e.g., 505)
OR
Press Volume button to select group and
Press Right Soft button to move cursor.
[505] STN.GROUP
3. Dial feature option number.(0-7, e.g., 0)
OR
Press Volume button to scroll options and press
Right Soft button to move cursor.
[505] STN GROUP
4. DIAL group type.(e.g., 1)
OR
Press Volume button to make selection.
Press Left Soft button to move cursor to TYPE.
5. Dial feature option number.(0-6, e.g., 1)
OR
Press Volume button to scroll options and
press Right Soft button to move cursor.
[505] STN GROUP
6. Dial ring option.(0-2, e.g., 0)
OR
Press Volume button to make selection.
Press Left Soft button to move cursor
back to RING or press Right Soft button to
return to step 2.
[505] STN GROUP
TYPE:NORMAL GRP
TYPE:NORMAL GRP
TYPE:VMAA GROUP
TYPE:VMAA GROUP
[505] STN GROUP
RING:DISTRIBUTE
RING:SEQUENTIAL
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
7. Dial next feature option and continue.
OR
Press Volume button to select option and
press Right Soft button.
OR
Press Left Soft button to return to step 2.
[505] STN GROUP
RING:SEQUENTIAL
8. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 203
MMC 204
MMC 600
MMC 607
© SAMSUNG Electronics Co., Ltd.
ASSIGN UA DEVICE
COMMON BELL CONTROL
ASSIGN OPERATOR GROUP
UCD OPTIONS
2-185
CHAPTER 2. MMC Programming
[602] STATION GROUP NAME
Allows the system administrator or technician to enter an 11-character name to identify an
individual station group.
CONDITIONS
NONE
INPUT CHARACTERS
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 602.
Display shows:
[500] SGR NAME
2. Dial group number.(e.g., 505)
OR
Press Volume button to make selection and
press Left or Right Soft button to move cursor.
[505] SGR NAME
3. Enter in name using above method and table.
[505] SGR NAME
TELECOMS
4. Press Left or Right Soft button to return to step 2.
OR
Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 104
MMC 404
MMC 601
2-186
STATION NAME
TRUNK NAME
ASSIGN STATION GROUP
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[603] ASSIGN TRUNK GROUP
Allows the assignment of trunks to a specific trunk group or to several trunk groups. This is
very useful in the programming of LCR when more than one trunk is to be in several
dialling plans. There are two different modes of operation:(1) sequential and(2) distribute.
There are 30 programmable trunk groups with up to 99 members per group.
ASSIGN TRUNK GROUP
One trunk can appear in more than one trunk group. If necessary, delete the trunk
member from other groups to prevent accidental access.
CONDITIONS
NONE
DEFAULT DATA
ALL LOOP/ISDN TRUNKS: 9
ALL TIE TRUNKS: 801
ALL VOIP NETWORKING TRUNKS: 803
ALL VOIP H.323 TRUNKS: 804
ALL VOIP SIP TRUNKS: 805
ACTION
DISPLAY
1. Press Transfer button and enter 603.
Display shows:
[9]
TRK GROUP
2. Enter in valid trunk group.(e.g., 9)
OR
Press Volume button to make selection and
press Right Soft button to advance cursor.
[9]
TRK GROUP
3. Press Right Soft button to change mode.
OR
Press Volume button to change mode to member.
[9]
TRK GROUP
4. Press Right Soft button to move cursor to number
of member and enter valid member number
(e.g., 05) via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
[9]
TRK GROUP
© SAMSUNG Electronics Co., Ltd.
MODE:SEQUENTIAL
MODE:SEQUENTIAL
MEMBER 01:NONE
MEMBER 05:NONE
2-187
CHAPTER 2. MMC Programming
5. Enter valid trunk number.(e.g., 729)
OR
Press Volume button to make selection and
press Right Soft button to return to step 2.
[9]
TRK GROUP
MEMBER 01:729
6. Repeat steps 1-5 to remove trunk from group 9
if necessary.
7. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
LCR PROGRAMMING
MMC 710
MMC 711
MMC 712
MMC 713
LCR DIGIT TABLE
LCR TIME TABLE
LCR ROUTE TABLE
LCR MODIFY DIGIT TABLE
VoIP PROGRAMMING
MMC 832
MMC 833
2-188
VOIP ACCESS CODE
VoIP IP TABLE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[604] ASSIGN STATION TO PAGE ZONE
Allows the technician to assign a phone to any of the five internal paging zones.
Each page zone can have up to 99 members. A phone may be assigned to more than one
zone. Page zone(*) will page all external page zones as well as all phones that are members
of page zone 0.
CONDITIONS
NONE
DEFAULT DATA
NO STATIONS ASSIGNED
ACTION
DISPLAY
1. Press Transfer button and enter 604.
Display shows:
INT.PAGE ZONE(0)
2. Enter the page zone number.(0-4, e.g., 3)
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
INT.PAGE ZONE(3)
3. Enter index number(e.g., 05) via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
INT.PAGE ZONE(3)
4. Enter station number(e.g., 205) via dial keypad.
OR
Press Volume button to make selection and press
Right Soft button to move cursor.
INT.PAGE ZONE(3)
MEMBER 01:NONE
MEMBER 01:NONE
MEMBER 05:NONE
MEMBER 05:205
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-189
CHAPTER 2. MMC Programming
[605] ASSIGN EXTERNAL PAGE ZONE
Determines which relays will close when one of the four external page zones is accessed.
The OfficeServ 500 system must be equipped with a MISC daughter-board to
allow external paging.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 605.
Display shows first page zone:
EXT. PAGE ZONE(5)
2. Dial page zone number.(e.g., 6)
OR
Use Volume button to select desired page zone
numbers and press Right Soft button to move the cursor.
EXT. PAGE ZONE(6)
3. Dial member number.(e.g., 3)
OR
Use Volume button to select member numbers
and press Right Soft button to move the cursor.
OR
Press Left Soft button to return to step 2 above.
EXT. PAGE ZONE(6)
4. Dial relay number via dial keypad(e.g., 362)
and press Right Soft button to return to step 2.
OR
Press Left Soft button to return to step 3 above.
EXT. PAGE ZONE(6)
MEMBER 1 :NONE
MEMBER 1 :NONE
MEMBER 3 :NONE
MEMBER 3 :362
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-190
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[606] ASSIGN SPEED BLOCK
Provides a means of adding or deleting speed dial blocks to the system or an individual
phone. With the ability to delete a block or blocks of speed dial, it will not be necessary to
waste these on such items as voice mail, DPIMs or stations that do not require the ability to
use speed dial. The Free List will show how many bins are left to be assigned.
A library of up to 2500 speed dial numbers may be allocated as needed. The system list can
have up to 500 numbers(950 numbers when MMC 861 SYSTEM SPEED BIN is set to
MAX 950) and each station can have up to 50 numbers. Speed dial numbers are assigned in
blocks of ten. Each speed number may contain up to 24 digits.
CONDITIONS
NONE
DEFAULT DATA
SYSTEM: 200 ENTRIES
STATIONS: 1 BLOCKS ASSIGNED
ACTION
DISPLAY
1. Press Transfer button and enter 606.
Display shows:
FREE LIST:20
2. Press Right Soft button to advance next line.
FREE LIST:20
OR
You can view BUSY LIST using Volume button.
SYSTEM:20
SYSTEM:20
BUSY LIST:180
SYSTEM:20
3. Make a selection of SYSTEM or EXT using.
Volume button and press Right Soft button to
advance cursor.
FREE LIST:20
4. Enter desired extension number via dial keypad.
(e.g., 205)
OR
Press Volume button to make selection and press
Right Soft button to advance cursor.
FREE LIST:20
© SAMSUNG Electronics Co., Ltd.
EXT201:1
EXT205:1
2-191
CHAPTER 2. MMC Programming
5. Enter valid number for bins.
(e.g., 0-5 for EXT or 00-50 for SYSTEM)
OR
Press Volume button to make selection.
OR
Press Hold button to delete bin(s).
FREE LIST:20
EXT205:5
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
DEFAULT DATA
SYSTEM: 200 ENTRIES
STATIONS: 1 BLOCKS ASSIGNED
RELATED ITEMS
MMC 105
MMC 106
MMC 705
MMC 706
MMC 861
2-192
TATION SPEED DIAL
TATION SPD NAME
SSIGN SYSTEM SPEED DIAL
YSTEM SPEED DIAL BY NAME
YSTEM OPTIONS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[607] UCD OPTIONS
Sets up UCD options when an AA card has been installed. MMC 601 must have already
been used to define a UCD group with an overflow destination of an AA port or group.
(A group is preferred over a port because a group allows multiple paths into the AA card
and therefore has greater traffic handling capabilities.) When a group overflow timer in
MMC 601 expires, the caller will be routed to the AA card It is here that the caller is played
the UCD ‘FIRST MESSAGE’ and ‘SECOND MESSAGE’ while in queue. This will
continue until an agent becomes free or the caller is transferred to a final destination.
This MMC includes options to select messages to play to a caller. These messages can be
as follows:
Message
MESSAGES 01-48
Description
These can be created using the AAREC Soft button(programmed on
phones by using MMC 722 or 723). A total of two minutes of message time
is available and can be divided up into 1 to 48 messages.
MESSAGES 49-64
© SAMSUNG Electronics Co., Ltd.
These are pre-programmed as follows:
49
‘Thank you for calling, please dial your party’s extension number’.
50
‘Invalid number, please try again’.
51
‘I’m sorry, there is no answer’.
52
‘I’m sorry, that station is busy’.
53
‘One moment please’.
54
‘Transferring’.
55
‘I’ll transfer you’.
56
‘Good-bye’.
57
‘Thank you’.
58
‘Please hold for the operator’.
59
‘Please hold for assistance’.
60
‘Thank you, good-bye’.
61
‘I’m sorry, all stations are presently busy’.
62
‘I’m sorry, all stations are still busy’.
63
‘Please call back later’.
64
‘I’m sorry, not a valid selection’.
2-193
CHAPTER 2. MMC Programming
The following program options apply:
No
00
Option
FIRST MESSAGE
Description
After the caller has overflowed from the UCD group, the first
message will immediately play. For instructions on how to make
these recordings, see the User Instructions Section, Auto
Attendant and Uniform Call Distribution System Administration.
The default message is #61 ‘I’m sorry, all stations are presently
busy’.
This message will only be played once for the caller.
01
SECOND MESSAGE
If no agent has become free after the UCD recall time(see UCD
Recall), the caller will be played the second message.
For instructions on how to make these recordings, see the User
Instructions Section, Auto Attendant and Uniform Call
Distribution System Administration. The default message is #62
‘I’m sorry, all stations are still busy’.
This message will be repeated for as long as the caller is in
queue, at an interval specified in the UCD Recall Timer below.
02
EXIT CODE
While the caller is hearing a message(but not during MOH),
the caller may dial the DTMF digit specified here and be
transferred immediately to the final destination(see Final
Destination). The exit code is optional and does not need to be
used. If used, the first and second messages may be modified to
provide instructions on its use.
03
RETRY COUNT
The UCD program is designed to route a caller to a ‘final
destination’ after a programmable number of ‘loops’ through the
UCD message. The range of this counter is 0 to 99. 00 means
that there is no retry counter and the caller will remain in the
UCD queue until answered. Any non zero value will route a caller
through the UCD loop that many times before going to the final
destination. The UCD will route calls to the final destination
immediately if all members of the group are either out of group or
in DND.
Example: If this counter is set to 02, callers reaching a busy
group will hear the first UCD message, be placed on hold, hear
the second UCD message, be placed on hold, and finally hear
the second message again before being transferred to the final
destination.
2-194
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
No
04
Option
FINAL DESTINATION
Description
This is the final destination for the caller if not answered by a
UCD agent.
This destination is only reached if(a) the caller dials an exit
digit during a message or(b) the retry count has expired. The
final destination can be a station number, a group number,
a disconnect or another plan. Plans are entered by pressing
A button plus two digits 01-12. A disconnect is entered as a
destination of NONE(Hold button).
If the final destination is a voice mail port, the port will receive
a FWD from UCD group integration message. The final
destination will forward or overflow.
If the forward to destination is a voice mail port the port will
receive FWD from UCD group integration message. If the
final destination is not forwarded, the call will ring or camp on
to the final destination indefinitely.
To ensure that you do not get a situation where all the call
buttons are busy on the final destination it is advisable to
make the final destination a group(even if the group has only
one station in it.)
05
RING NEXT TIME
This timer must be shorter than the overflow timer in MMC
601. If a higher value is entered, the display will show invalid
entry. In the case where a UCD group has the ring next timer
set at 000, an unanswered call will rotate evenly among all
agents until it is answered. The UCD greetings will be heard
during this routing process, but can be removed by defining
the UCD messages in MMC 607 as unrecorded message
numbers.
This will simulate a circular hunt group.
06
UCD RECALL TIME
After a caller has heard a UCD announcement, he/she will be
placed on hold until an agent becomes available or the UCD
recall timer expires. When the UCD recall timer expires, the
caller will again hear the UCD announcement. The range is
00-99. The default is 10.
07
MOH SOURCE
This option determines what Music on Hold source the callers
will be connected to between messages. The choice is either
an external source, AA message defined in MMC 736, or a
Built-In Voice Mail Card message defined in MMC 756.
08
WRAP-UP TIME
This option will make a UCD agent unavailable to receive
additional UCD calls after hanging up from the last one. This
is to allow agents to complete work associated with the
previous call before the next call begins ringing. The range is
000-250. The default is 010.
© SAMSUNG Electronics Co., Ltd.
2-195
CHAPTER 2. MMC Programming
No
09
Option
AUTO LOG OUT
Description
This YES/NO option determines if a station will automatically log
out of the UCD group when the RING NEXT timer expires.
This setting will be ignored if the RING NEXT timer is set to 000.
10
ALLOUT FINAL
This YES/NO option determines if calls forward to the UCD final
destination when all stations are logged out of the UCD group.
If no UCD final destination is assigned then the call will
disconnect.
11
AGENT PIN NO
This YES/NO option determines if an agent is required to enter
an Agent ID when logging on to this group. The Agent ID can be
entered in MMC 717.
12
GROUP BUSY NEXT
This YES/NO option determines if all agents are busy, specifies
whether the next port is called immediately during overflow time.
CONDITIONS
NONE
DEFAULT DATA
FIRST MSG: 61
SECOND MSG: 62
EXIT CODE: NONE
RETRY COUNT: 03
FINAL DEST: 500
RING NEXT: 30 SEC
UCD RECALL: 10 SEC
MOH SOURCE: NONE
WRAP-UP: 10 SEC
AUTO LOG OUT: ON
ALL OUT TO FINAL: OFF
AGENT PIN NO: OFF
GBUSY NEXT: OFF
2-196
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
ACTION
DISPLAY
1. Press Transfer button and enter 607.
Display shows:
[530] UCD OPTION
2. Press Volume button to select UCD group or
dial group number.
OR
Press Left Soft button to position cursor
under message number and enter new message.
OR
Press Right Soft button and advance to next option
using the Volume buttons to select an option.
[542] UCD OPTION
3. Press Right Soft button and advance to next option
using the Volume buttons to make a selection.
OR
Make a selection using the dial pad.
[530] UCD OPTION
4. Press Left Soft button to enter the selection
and to return to step 1.
OR
Press Right Soft button to return to step 3.
[530] UCD OPTION
FIRST MSG
FIRST MSG
:61
:61
[530] UCD OPTION
FIRST MSG
:25
[530] UCD GROUP
UCD RECALL:10 SEC
UCD RECALL:10 SEC
EXIT CODE
:NONE
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 601
MMC 733
© SAMSUNG Electronics Co., Ltd.
ASSIGN STATION GROUP
AA PLAN PROGRAMMING
2-197
CHAPTER 2. MMC Programming
[608] ASSIGN REVIEW BLOCK
Provides means of adding or deleting CID review blocks to an individual phone. With the
ability to delete a block or blocks of CID review, it will not be necessary to waste these on
such items as voice mail, DPIMs or for phones that do not have displays. The free list will
show how many bins are left to be assigned. The system has 2000 total bins. Each phone
may be assigned a maximum of 50 bins.
CONDITIONS
NONE
DEFAULT DATA
PHONES: 10 BINS
ACTION
DISPLAY
1. Press Transfer button and enter 608.
Display shows first station:
[201] REVIEW BLK
2. Enter desired EXT number.(e.g., 205)
OR
Press Volume button to make selection and
press Right Soft button to advance cursor.
[205] REVW BLOCK
3. Enter valid number for bins.(e.g., 5)
OR
Press Volume button to make selection.
OR
Press Hold button to delete bin(s).
[205] REVW BLOCK
10:0060 FREE
10:0060 FREE
50:0010 FREE
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 119
MMC 312
MMC 725
2-198
CALLER ID DISPLAY
ALLOW CALLER ID
SMDR OPTIONS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[609] CALL LOG BLOCK
Provides means of adding or deleting Call LOG blocks to an individual phone. With the
ability to delete a block or blocks, it will not be necessary to waste these on such items as
voice mail, DPIMs or for phones that do not have displays. The free list will show how
many bins are left that be assigned. The system has 2000 total bins. Each phone may be
assigned a maximum of 50 bins.
CONDITIONS
NONE
DEFAULT DATA
PHONES: 10 BINS
ACTION
DISPLAY
1. Press Transfer button and enter 609.
Display shows first station:
[201] LOG BLOCK
2. Enter desired EXT number.(e.g., 205)
OR
Press Volume button to make selection and
press Right Soft button to advance cursor.
[205] LOG BLOCK
3. Enter valid number for bins.(e.g., 5)
OR
Press Volume button to make selection.
OR
Press Hold button to delete bin(s).
[205] LOG BLOCK
10:0070 FREE
10:0070 FREE
50:0030 FREE
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-199
CHAPTER 2. MMC Programming
[611] ALLOW TEXT MESSAGING
This program allows you to send a text message to a busy station or during an OHVA.
Up to 100 stations can be set to the system.
CONDITIONS
NONE
DEFAULT DATA
ITP-5012L sets are automatically set to USED
ACTION
DISPLAY
1. Press Transfer button and enter 611.
Display shows:
[201] TMSG STN
2. Enter the number of a station.
OR
Press Volume button to make selection and
press Right Soft button to advance cursor.
[202] TMSG STN
3. Specify whether text message will be used or not.
[202] TMSG STN
NOT USED:100 FREE
NOT USED:100 FREE
USED
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 117
2-200
EDIT TEXT MESSAGE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[612] ALLOW GROUP CONFERENCE
This program allows a station to use the Group conference call feature. Up to 100 stations
can be allowed in the system. Each user can have up to 5 pre programmed conferences.
This feature is only for Large LCD Phone(ex: ITP-5012L,DS-5012L. WIP-5000M)
CONDITIONS
NONE
DEFAULT DATA
Large LCD Phone sets are automatically set to USED
ACTION
DISPLAY
1. Press Transfer button and enter 612.
Display shows:
[201] CONF STN
2. Enter the number of a station.
OR
Press Volume button to make selection and
press Right Soft button to advance cursor.
[202] CONF STN
3. Specify whether a group conference be used
or not.
[205] CONF STN
NOT USED:100 FREE
NOT USED :100 FREE
USED
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 118
© SAMSUNG Electronics Co., Ltd.
CONFERENCE GROUP
2-201
CHAPTER 2. MMC Programming
[614] STATION/TRUNK USE GROUP
This program allows you to set a call group in which each station or Trunk line is included.
It is useful if you want to limit a call between stations, outgoing calls through a Trunk line,
or call-pickup.
CONDITIONS
Call group can be set from 001 to 300 for station, and from 301 to 500 for trunk.
DEFAULT DATA
ALL STATIONS: 001
ALL TRUNKS: 301
ACTION
DISPLAY
1. Press Transfer button and enter 614.
Display shows first station:
STATION GROUP
2. Enter [0] if you want to set a call group to a station.
Enter [1] if user want to set a call group to a trunk.
OR
Press Volume button to make selection and press
Right Soft button to advance cursor.
TRUNK GROUP
3. Enter a number you want.
OR
Press Volume button to make selection and
press Right Soft button to advance cursor.
TRUNK GROUP
4. Enter the number of the call group you want to set.
OR
Press Volume button to make selection and
press Right Soft button to advance cursor.
TRUNK GROUP
201:001
701:301
702:301
702:302
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 304
MMC 316
MMC 317
MMC 428
2-202
ASSIGN EXTENSION/TRUNK USE
COPY STATION/TRUNK USE
ASSIGN STATION/STATION USE
ASSIGN TRUNK/TRUNK USE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[615] MGI GROUP
This optional program sets designated MGI ports for specific services. This allows
‘grading’ of MGI card(s) for traffic conditions. The MGI ports can be segregated into
groups. Keep in mind that any entries made here can be ineffective, if conflicting entries
exist in MMC616.
No
0
Type
LOCAL ITP
Description
This determines what MGI ports can be used with ITP phones across a
private IP network
1
PUB IP ITP
This determines what MGI ports can be used with ITP phones on a
public IP network.
2
VOIP NTWK
This determines what MGI ports can be used for enhanced proprietary
Samsung VoIP networking between OfficeServ 500 systems across a
private IP network.
3
PUB IP NTWK
This determines what MGI ports can be used for enhanced proprietary
Samsung VoIP networking between OfficeServ 500 systems on a public
IP network
4
VOIP TRUNK
This determines what MGI ports can be used as industry-standard
H.323 or SIP VoIP trunks for communications across a private network
5
PUB IP TRK
This determines what MGI ports can be used as industry-standard
H.323 or SIP VoIP trunks for communications on a public network
6
MGI3 NEEDED
This determines what MGI ports can be used for T.38 facsimile
communications across a private network.
7
PUB IP MGI3
This determines what MGI ports can be used for T.38 facsimile
communications on a public network.
8
ITP PAGED
This determines what MGI ports can be used with station page to ITP
phones across a private IP network
The MGI ports can be allow two selection modes: Sequential or Distributed.
The members of each selection are the actual ports on the MGI card(s)
CONDITIONS
NONE
© SAMSUNG Electronics Co., Ltd.
2-203
CHAPTER 2. MMC Programming
DEFAULT DATA
LOCAL ITP: MGI1, MGI2, MGI3
PUB IP ITP: MGI2, MGI3
VOIP NTWK: MGI2, MGI3
PUB IP NTWK: MGI2, MGI3
VOIP TRUNK: MGI2, MGI3
PUB IP TRK: MGI2, MGI3
MGI3 NEEDED: MGI3
PUB IP MGI3: MGI3
ITP PAGED: MGI1, MGI2, MGI3
ACTION
DISPLAY
1. Press Transfer button and enter 615.
Display shows the first available option:
USER: LOCAL ITP
2. Press Volume button to select an user type.
Press Right Soft button to move cursor.
USER: LOCAL ITP
3. Press Volume button to select an option and
press Right Soft button to move cursor.
USER: LOCAL ITP
4. Press Volume button to select an data and
press Right Soft button to store data and
move cursor to return to step 1.
USER: LOCAL ITP
MODE:SEQUENTIAL
MODE:SEQUENTIAL
MODE:SEQUENTIAL
MODE:SEQUENTIAL
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 616
MMC 831
MMC 838
MMC 840
2-204
MGI USER
MGI PARAMETERS
PRIVATE IP ADDRESSES
IP SET INFORMATION
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[616] MGI USER
This optional program selects which specific MGI ports will be dedicated on a per-port
basis for IP station/trunk devices. If this MMC is not utilized, allocation of MGI ports will
be controlled by MMC615. By defining dedicated MGI port usage, the IP station/trunk
selected will always use the port programmed. MGI ports can be assigned for digital
stations(2XX~2XXX), private and public ITP stations(32XX), VoIP Networking
trunks(83XX), H.323 trunks(84XX), SIP trunks(85XX) and MGI3 facsimile. Only one
assignment per MGI port is permitted. Any entries made here will override entries made in
MMC615.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 616.
Display shows the first available option:
[3801] MGI USER
2. Enter MGI dial number.
OR
Press Volume button to select an MGI port and
press Right Soft button to move cursor.
[3801] MGI USER
3. Enter MGI user dial number.
OR
Press Volume button to select an MGI user and
press Right Soft button to store and move cursor.
[3801] MGI USER
NONE
NONE
NONE
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 615
MMC 616
MMC 831
MMC 834
MMC 837
MMC 838
MMC 840
MMC 841
© SAMSUNG Electronics Co., Ltd.
MGI GROUP
MGI USER
MGI PARAMETERS
H.323 OPTIONS
SIP OPTIONS
PRIVATE IP ADDRESSES
IP SET INFORMATION
SYSTEM IP OPTIONS
2-205
CHAPTER 2. MMC Programming
[700] COPY COS CONTENTS
This MMC allows the technician to duplicate a class of service to make it easier to have
multiple similar classes of service.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 700.
Display shows:
COPY COS ITEMS
2. Dial selected COS to copy.(e.g., 05)
OR
Press Volume button to select COS and press
Right Soft button to move cursor and advance
to next step.
COPY COS ITEMS
3. Dial target COS.(e.g., 06)
OR
Press Volume button to select COS and press
Right Soft button to move cursor back to step 2.
COPY COS ITEMS
4. Press F key to advance MMC 701 and press
Right Soft to advance cursor.
COS CONTENTS(06)
COS01 COS01
COS05 COS01
COS05 COS06
TOLL LEVEL:A
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 701
2-206
ASSIGN COS CONTENTS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[701] ASSIGN COS CONTENTS
Similar to MMC 700 but does not allow a copy command. This MMC is primarily used for
creating a new class of service. If the unsupervised conference feature is allowed, a
programmed CONF key must be available to allow re-entry into a conference call.
There are 30 classes of service available.
This MMC is divided into 5 categories.
No
0
1
Category
TOLL LEVEL
USABLE
Description
TOLL
LEVEL
0
A
Follow toll class A(Unrestricted)
1
B
Follow toll class B in MMC 702, 703
2
C
Follow toll class C in MMC 702, 703
3
D
Follow toll class D in MMC 702, 703
4
E
Follow toll class E in MMC 702, 703
5
F
Follow toll class F in MMC 702, 703
6
G
Follow toll class G in MMC 702, 703
7
H
Follow toll class H(All restricted)
No
COS
Default
Description
00
AA CALER
YES
Auto answer control by caller
01
ABSENCE
YES
Absence
02
ALM CLR
YES
Alarm Clear
03
AUTO RDL
YES
Retry on busy
04
CALLBACK
YES
Callback
05
CLIP ABN
YES
Caller ID Abandon
06
CLIP INQ
YES
Caller ID Inquire
07
CLIP INV
YES
Caller ID Investigate
08
CONFER.
YES
Conference
09
DALM CLR
YES
DISA alarm ring clear
10
DIRECT.
YES
Directory dial
11
DISA
YES
Allow DISA use
12
DND
YES
Do Not Disturb
13
DND FWRD
YES
Forward Do Not Disturb
14
DND OVRD
YES
Do Not Disturb override
15
DOOR
YES
Door ring answer
16
DSS
YES
Direct station select
17
DTS
YES
Direct trunk select
18
EXT AREC
NO
Intercom call automatic record(SVM-800)
19
EXT FWD
YES
External call forward
FEATURES
© SAMSUNG Electronics Co., Ltd.
2-207
CHAPTER 2. MMC Programming
No
1
2-208
Category
Description
USABLE
20
FEATURE
YES
Transfer button
FEATURES
21
FLASH
YES
Trunk flash
22
FOLLOW-ME
YES
Call forward-follow me
23
FORWARD
YES
Call forwarding
24
FWDTOVMS
YES
Call forward to SVM-800
25
GRP I/O
YES
Group in/out
26
HOLD
YES
Hold
27
HOTLINE
YES
Hot line and Off hook selection
28
INTERCOM
YES
Intercom call
30
MESSAGE
YES
Message
31
MM PAGE
YES
Meet me page
32
NEW CALL
YES
New call
33
OHVAED
YES
Receive Off hook voice announcement
34
OHVAING
YES
Make Off hook voice announcement
35
ONEA2
YES
1A2 emulation
36
OPERATOR
YES
Call to Operator
37
OUT TRSF
YES
Outgoing transfer
38
OVERRIDE
NO
Barge-In
39
PAGE 0
YES
Page zone 0 Paging
40
PAGE 1
YES
Page zone 1 Paging
41
PAGE 2
YES
Page zone 2 Paging
42
PAGE 3
YES
Page zone 3 Paging
43
PAGE 4
YES
Page zone 4 Paging
44
PAGE 5
YES
Page zone 5 Paging
45
PAGE 6
YES
Page zone 6 Paging
46
PAGE 7
YES
Page zone 7 Paging
47
PAGE 8
YES
Page zone 8 Paging
48
PAGE 9
YES
Page zone 9 Paging
49
PAGE *
YES
Page zone * Paging
51
PICKUP
YES
Call pickup
52
PRB
YES
Privacy Release and Bridge
53
REM. HOLD
YES
Remote Hold
54
RNG PLAN
YES
Ring Mode Change
55
SECURE
YES
Barge-In secure
56
SET RLOC
NO
Set Relocation
57
SSPD TOL
YES
System Speed dial toll check
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
No
1
2
Category
Description
USABLE
58
STN LOCK
YES
Station Lock
FEATURES
59
SYS SPD
YES
System Speed dial
60
TRK AREC
NO
Trunk call automatic record(SVM-800)
61
TRK EHLD
YES
Trunk call exclusive hold
62
UNCO CNF
YES
Unsupervised Conference
63
VM AREC
NO
Auto Record(SVMi)
64
VM AME
NO
Answer Machine Emulation(SVMi)
65
VM REC
NO
Call Record(SVMi)
66
VMS PSWD
NO
VMS password(SVM-800)
67
VMS REC
NO
VMS Call Record(SVM-800)
STN GROUP 01-80
YES
Station group 01~80 calling
TRK GROUP 01-30
YES
Trunk group 01~30 calling
BIVMS STN 01-16
YES
SVMi port 01~16 calling
CALL STATION
GROUPS
3
CALL TRUNK
GROUPS
4
CALL TO
BIVMS
STN(SVMi).
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
ACTION
DISPLAY
1. Press Transfer button and enter 701.
Display shows:
COS CONTENTS(01)
2. Dial COS.(e.g., 06)
OR
Press Volume button to select COS number and
press Right Soft button to move cursor.
COS CONTENTS(06)
3. Dial COS contents categories.
(e.g., 1 for usable feature)
OR
Press Volume button to select COS categories
and press Right Soft button to move cursor.
COS CONTENTS(06)
© SAMSUNG Electronics Co., Ltd.
TOLL LEVEL:A
TOLL LEVEL:A
00:AA CALER :YES
2-209
CHAPTER 2. MMC Programming
4. Dial COS usable feature option.(e.g., 12)
OR
Press Volume button to select option and press
Right Soft button to move cursor.
5. Dial 0 for NO or 1 for YES.
OR
Press Volume button to select option and
press Right Soft button to return to step 4.
COS CONTENTS(06)
12:DND
:YES
COS CONTENTS(06)
12:DND
:NO
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 700
MMC 702
MMC 703
COPY COS CONTENTS
TOLL DENY TABLE
TOLL ALLOWANCE TABLE
TOLL RESTRICTION
MMC 702
MMC 703
MMC 704
MMC 709
2-210
TOLL DENY TABLE
TOLL ALLOWANCE TABLE
ASSIGN WILD CHARACTER
TOLL PASS CODE/SPECIAL CODE TABLE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[702] TOLL DENY TABLE
Provides a way to make toll restriction(call barring) very easy and flexible. There are 500
entries allowed in the deny and each entry index can be assigned to a class of service. Each
index can have up to 12 digits. With the use of wild cards(MMC 704 Assign Wild
Character), more flexibility can be built into toll restriction. Wild cards can be used
repeatedly in the dial string, limited only to what is allowed or denied in MMC 704. There
are six toll levels, B to G, that are programmable. Toll level A is set as unrestricted by
default and toll level H is set as in-house only by default.
CONDITIONS
NONE
DEFAULT DATA
ALL ENTRIES ARE SET TO 0
PROGRAM BUTTONS
A
B
C
Used to wild card X entered
Used to wild card Y entered
Used to wild card Z entered
ACTION
DISPLAY
1. Press Transfer button and enter 702.
Display shows:
DENY(001):BCDEFG
2. Dial index number.(e.g., 005)
OR
Press Volume button to select index and press
Right Soft button to move cursor.
DENY(005):BCDEFG
3. Enter toll pattern via dial pad.(e.g., 212)
DENY(005):BCDEFG
OR
Enter wild card(e.g., 21X) from above list and
press Right Soft button to move cursor to COS
options.
© SAMSUNG Electronics Co., Ltd.
:000000
:000000
212
:000000
DENY(005):BCDEFG
21X
:000000
2-211
CHAPTER 2. MMC Programming
4. Press Volume button to move cursor along line
until under toll class mark.(e.g., E)
Enter a 1 for YES or 0 for NO and press
Right Soft button to store and return to step 1.
OR
Press Left Soft button to return to step 2.
DENY(001):BCDEFG
212
:000100
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 301
MMC 701
MMC 703
MMC 704
2-212
ASSIGN STATION COS
ASSIGN COS CONTENTS
TOLL ALLOWANCE TABLE
ASSIGN WILD CHARACTER
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[703] TOLL ALLOWANCE TABLE
Provides a way to make toll restriction very easy and flexible. There are 250 allowable
entries in the allow table for a OfficeServ 500-M system and 500 allowable entries for a
OfficeServ 500-L system and each entry index can be assigned to a class of service. Each
index can have up to 12 digits. With the use of wild cards(MMC 704 Assign Wild
Character), more flexibility can be built into toll restriction. There are six toll levels, B to G,
that are programmable. Toll level A is set as unrestricted by default, and toll level H is set
as in-house only by default.
CONDITIONS
NONE
DEFAULT DATA
ALL ENTRIES ARE SET TO 0
PROGRAM BUTTONS
A
B
C
Used to wild card X entered
Used to wild card Y entered
Used to wild card Z entered
ACTION
DISPLAY
1. Press Transfer button and enter 702.
Display shows:
ALOW(001):BCDEFG
2. Dial index number.(e.g., 005)
OR
Press Volume button to select index and
press Right Soft button to move cursor.
ALOW(005):BCDEFG
3. Enter toll pattern via dial pad.(e.g., 202)
OR
ALOW(005):BCDEFG
Enter wild card(e.g., 21X) from above list and
press Right Soft button to move cursor to COS
options.
© SAMSUNG Electronics Co., Ltd.
:000000
:000000
202
:000000
ALOW(005):BCDEFG
20X
:000000
2-213
CHAPTER 2. MMC Programming
4. Press Volume button to move cursor along line
until under toll class mark.(e.g., E)
Enter a 1 for YES or 0 for NO and press
Right Soft button to store and return to step 1.
OR
Press Left Soft button to return to step 2.
ALOW(001):BCDEFG
202
:000100
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 301
MMC 701
MMC 702
MMC 704
2-214
ASSIGN STATION COS
ASSIGN COS CONTENTS
TOLL DENY TABLE
ASSIGN WILD CHARACTER
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[704] ASSIGN WILD CHARACTER
Provides flexibility to toll restriction(call barring) when a specific numbering plan is so
desired. There are only three entry tables but more than one digit can be assigned per table
if needed.
CONDITIONS
NONE
DEFAULT DATA
X ENTRIES SET TO 1
OTHER ENTRIES SET TO 0
ACTION
DISPLAY
1. Press Transfer button and enter 704.
Display shows:
2. Press Volume button to select X, Y, or Z.(e.g., Z)
and press Right Soft button to advance cursor to
option line.
3. Press Volume button to move cursor to option
digit desired(e.g., 5) and enter 1.(put under other
digits as required)
Press Left Soft button to return to step 2.
OR
Press Right Soft button to return to step 1.
:0123456789*#
X:111111111111
:0123456789*#
Z:000000000000
:0123456789*#
Z:000001000000
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 702
MMC 703
© SAMSUNG Electronics Co., Ltd.
TOLL DENY TABLE
TOLL ALLOWANCE TABLE
2-215
CHAPTER 2. MMC Programming
[705] ASSIGN SYSTEM SPEED DIAL
Enables the assignment of system speed dialling numbers. There are up to 500 entries
available(950 entries when MMC 861 SYSTEM SPEED BIN is set to MAX 950) for
programming(see MMC 606). Each speed dial number consists of a trunk or trunk group
access code followed by a separator and up to 24 digits to be dialled. These dialled digits
may consist of 0-9, and #. If the system recognizes a valid trunk or trunk group access
number, it will automatically insert the separator.
CONDITIONS
NONE
DEFAULT DATA
NONE
PROGRAM BUTTONS
B
C
D
E
F
ANS/RLS
Used to insert a flash code ‘F’
Used to insert a pause code ‘P’
Used to insert a pulse/tone conversion code ‘C’
Used to mask/unmask following digits-shows as ‘[’ or ‘]’
Used to enter name for speed dial bin(see MMC 706)
Used to save the speed dial number and name to the MMC 728 CID
translation table.
ACTION
2-216
DISPLAY
1. Press Transfer button and enter 705.
Display shows:
SYS SPEED DIAL
2. Dial speed index desired.(e.g., 505)
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
SYS SPEED DIAL
3. Enter access code(e.g., 9/701) plus the phone
number up to 24 digits(digits will scroll under)
and press Right Soft button to return to step 2.
SYS SPEED DIAL
4. Press F key to toggle to MMC 706 step 3 to
enter name.
SYS SPEED NAME
500:
505:
505:9 121223456789
505:
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
5. If you want to save the speed dial number and
name data to the MMC 728 CID translation
table, Press ANS/RLS button and dial 1 for YES.
(The speed dial name must be exist)
SYS SPEED DIAL
ADD CLI XLT ?NO
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 606
MMC 706
MMC 728
MMC 861
© SAMSUNG Electronics Co., Ltd.
ASSIGN SPEED BLOCK
SYSTEM SPEED DIAL BY NAME
CLIP NAME TRANSLATION
SYSTEM OPTIONS
2-217
CHAPTER 2. MMC Programming
[706] SYSTEM SPEED DIAL BY NAME
Allows an 11-character name to be entered for each system speed dial location.
This name enables the speed dial number to be located when using the directory dial
feature. The directory dial feature allows the display phone user to select a speed dial
location by scanning its name.
CONDITIONS
NONE
INPUT CHARACTERS
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
DEFAULT DATA
NO NAMES
PROGRAM BUTTONS
ANS/RLS
Used to save the speed dial number and name to the MMC 728 CID
translation table.
ACTION
2-218
DISPLAY
1. Press Transfer button and enter 706.
Display shows:
SYS SPEED NAME
2. Dial system speed entry number.(e.g., 505)
OR
Press Volume button to select entry number and
press Right Soft button to move cursor.
SYS SPEED NAME
3. Enter name using dial keypad and above table
and press Right Soft button to return to step 2.
OR
Press the F key to toggle to speed dial number
to return to MMC 705, step 3.
SYS SPEED NAME
4. If you want to save the speed dial number and
name data to the MMC 728 CLI translation table,
press ANS/RLS button and dial 1 for YES.
(The speed dial number must be exist)
SYS SPEED NAME
500:
505:
505:TELECOMS
SYS SPEED DIAL
505:
ADD CLI XLT ?NO
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
5. Press Right Soft button to return to step 2 above.
OR
Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 606
MMC 705
MMC 728
© SAMSUNG Electronics Co., Ltd.
ASSIGN SPEED BLOCK
ASSIGN SYSTEM SPEED DIAL
CLIP NAME TRANSLATION
2-219
CHAPTER 2. MMC Programming
[707] AUTHORIZATION CODE
Enables the authorization feature on a per-class of service selection. There are 500
available entries. Authorization codes can be up to 4 to 10 digits.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 707.
Display shows:
AUTHOR.CODE(001)
2. Dial code index number.(e.g., 005)
OR
Press Volume button to selected index number
and press Right Soft button to move cursor.
AUTHOR.CODE(005)
3. Enter authorization code(minimum of four digits
and a maximum of 10 digits via dial keypad
(e.g., 1234567890) and press Right Soft button
to move cursor.
AUTHOR.CODE(005)
4. Enter class of service number 01-30.(e.g., 05)
OR
Press Volume button to select COS and press
Right Soft button to select and return to step 2.
AUTHOR.CODE(005)
C:01
C:01
1234567890
1234567890
C:01
C:05
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 305
2-220
ASSIGN FORCED CODE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[708] ACCOUNT CODE
Enables the account code entry feature. There are 999 available entries.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 708.
Display shows:
ACCOUNT CODE
2. Dial code index number.(e.g., 005)
OR
Press Volume button to selected index number
and press Right Soft button to move cursor.
ACCOUNT CODE
3. Enter account code(maximum 12 digits) via
dial keypad.(e.g., 1234)
and press Right Soft button to move cursor
back to step 2.
ACCOUNT CODE
001:
005:
005:1234
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 305
© SAMSUNG Electronics Co., Ltd.
ASSIGN FORCED CODE
2-221
CHAPTER 2. MMC Programming
[709] TOLL PASS CODE/SPECIAL CODE TABLE
This MMC provides a means to program three trunk code tables as described below.
No
0
Special Code
PBX CODE
Description
This table contains up to five entries and is used to identify the
trunk access codes needed for toll restriction to be properly
applied when the system is used either behind a PBX or with
CENTREX-supplied dial tone. Toll restriction will only be applied
on trunks flagged as PBX in MMC 401 if a trunk access code
entered in this table is dialled. Toll restriction will be applied to
the digits following the trunk access code.
1
SPECIAL CODE
This table identifies to the system dialling rules the special
feature codes used to activate central office custom calling
features such as CID Block and call waiting disable. The special
feature codes can be used on a per call basis without affecting
LCR or toll restriction programming. There is a maximum of
ten(10) entries available each of which may be up to four digits
long.
2
TOLL OVERRIDE
This table of eight entries is used to identify to the system
numbers that will bypass all dialling restrictions. This bypass
includes Toll restriction, Trunk access and forced authorization
or account codes. Each entry in the table can be up to 14 digits
long.
3
OVRD USE TRK GRP
This entry designates the trunk group that toll override calls will
access.
CONDITIONS
NONE
DEFAULT DATA
NONE
2-222
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
ACTION
DISPLAY
1. Press Transfer button and enter 709.
Display shows:
PBX ACCESS CODE
2. Select PBX , SPECIAL CODE, TOLL OVERRIDE
or OVRD USE TRK GRP.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
TOLL OVERRIDE
3. Enter index number.(e.g., 3)
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
TOLL OVERRIDE
4. Enter via dial keypad the desired access
feature code.(e.g., 911)
Press Right Soft button to enter and return
to step 3 and enter more entries.
TOLL OVERRIDE
1:
1:
3:_
3:911
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 401
MMC 702
MMC 703
MMC 305
TRUNK LINE/PBX LINE
TOLL DENY TABLE
TOLL ALLOWANCE TABLE
FORCED CODES
TOLL RESTRICTION
MMC 702
MMC 703
MMC 704
© SAMSUNG Electronics Co., Ltd.
TOLL DENY TABLE
TOLL ALLOWANCE TABLE
ASSIGN WILD CHARACTER
2-223
CHAPTER 2. MMC Programming
[710] LCR DIGIT TABLE
The LCR DIGIT TABLE contains all numerical digits for the completion of outgoing call
placement. This table works in conjunction with LCR ROUTE TABLE, LCR TIME
TABLE and LCR MODIFY DIGITS TABLE. There is a maximum 2000 with a digit string
length of 10 numerical digits. This system automatically maintains entered digit strings in
numerical order. The characters * and # are also accepted for use with feature codes.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 710.
Display shows:
LCR DIGIT (0001)
2. Dial LCR entry.(e.g., 0005)
OR
Press Volume button to select entry and press
Right Soft button to move cursor.
LCR DIGIT (0005)
3. Enter LCR digit string via the dial keypad and
press Right Soft button.
OR
Press Left Soft button to return to step 1.
LCR DIGIT (0005)
4. Enter digit length.(max: 31)
Cursor will move to RT(route selection).
LCR DIGIT
(0005)
5. Enter RT.(01-32)
Valid entry will return you to step 1.
LCR DIGIT
(0005)
DIGIT:
DIGIT:_
DIGIT:305426
LENGTH:10 RT:01
LENGTH:10 RT:01
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 712
2-224
LCR ROUTE TABLE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[711] LCR TIME TABLE
This table gives the flexibility to the system, through the LCR ROUTES, to allow calls
placed at any given time of day to use the least cost trunk route that is available. When
LCR ROUTE ADVANCE is allowed, it is possible for calls to be placed on more expensive
trunks on any given time of day. There are four possible time entries per day; the start time
of the next time period is the end time of the previous time period.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 711.
Display shows:
LCR TIME (SUN:A)
2. Dial day of week.(SUN-SAT, e.g., WED)
OR
Press Volume button to make day selection and
press Right Soft button.
LCR TIME (WED:A)
3. Dial time band.(A-D, e.g., B)
OR
Press Volume button to make selection and press
Right Soft button.
LCR TIME (WED:B)
4. Dial time via keypad.(24-hour format, e.g., 0800)
Cursor moves to LCRT.(reference MMC 712)
LCR TIME (WED:B)
5. Dial time table number.(1-4)
OR
Press Volume button to make selection and press
Right Soft button.
LCR TIME (WED:B)
HHMM:
HHMM:
HHMM:
LCRT:-
LCRT:-
LCRT:-
HHMM:0800 LCRT:-
HHMM:0800 LCRT:1
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 712
© SAMSUNG Electronics Co., Ltd.
LCR ROUTE TABLE
2-225
CHAPTER 2. MMC Programming
[712] LCR ROUTE TABLE
The LCR ROUTE TABLE is responsible for selecting a specific trunk group in the
completion of an outward bound call. This table works in conjunction with LCR DIGIT
TABLE, LCR TIME TABLE, LCR COS TABLE and LCR MODIFIED DIGITS TABLE.
After you dial a valid digit string, the system uses the LCR ROUTE TABLE to select a
specific predetermined trunk group. There is a maximum number of 32 routes available.
If more than one trunk group is available for call completion, the system uses the first
designated trunk group and then starts to utilize succeeding trunk groups. If all trunk
groups are busy in a selected route, call queue becomes active and allocates trunks as they
become available.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
2-226
DISPLAY
1. Press Transfer button and enter 712.
Display shows:
LCR ROUTE (01:1)
2. Dial LCR ROUTE table number.(e.g., 05)
OR
Press Volume button to selected table and press
Right Soft button to move cursor.
LCR ROUTE (05:1)
3. Dial TIME BAND index number 1-4.(e.g., 2)
OR
Press Volume button to selected index and press
Right Soft button to move cursor.
LCR ROUTE (05:2)
4. Dial LCR COS number 1-8.(e.g., 4)
OR
Press Volume button to selected COS and press
Right Soft button to move cursor.
LCR ROUTE (05:2)
5. Dial TRUNK GROUP access code.(e.g., 801)
OR
Press Volume button to selected access code and
press Right Soft button to move cursor.
LCR ROUTE (05:2)
C:1 G:NONE M:---
C:1 G:NONE M:---
C:1 G:NONE M:---
C:4 G:NONE M:---
C:4 G:801
M:---
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
6. Dial MODIFY DIGITS index number.(e.g., 050)
OR
Press Volume button to selected index number
and press Right Soft button to move cursor.
OR
Press Right Soft button to skip step and move
cursor to step 2.
LCR ROUTE (05:2)
C:4 G:801
M:050
LCR ROUTE (05:2)
C:4 G:801
M:---
7. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 310
MMC 710
MMC 711
MMC 713
© SAMSUNG Electronics Co., Ltd.
LCR CLASS OF SERVICE
LCR DIGIT TABLE
LCR TIME TABLE
LCR MODIFY DIGIT TABLE
2-227
CHAPTER 2. MMC Programming
[713] LCR MODIFY DIGIT TABLE
This program entry is also referred to as Outgoing dial Rules. This will give the system the
ability to add or delete a digit string or singular digit if needed to complete a call. A perfect
example is the adding of a digit ‘1 .An advantage is to insert a common carrier network
access code of 1010288. With these digits inserted, a long distance call will be placed over
a local line utilizing the common carrier network. The characters * and # can also be
entered. There are 200 modify digit entries available.
Option
Maximum Number Of Digit Entries
Number of digits to delete
15
Insert(before dialling string)
14
Append(after dialling string)
14
DIGIT STRING KEY
Insert String + Digit String(delete) + Append String
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
2-228
DISPLAY
1. Press Transfer button and enter 713.
Display shows:
LCR MODIFY (001)
2. Enter index number.(e.g., 005)
OR
Press Volume buttons to make selection and
press Right Soft button to move cursor.
LCR MODIFY (005)
3. Enter number of digits to delete.
OR
Press Right Soft button to skip step and move
cursor to next step.
LCR MODIFY (005)
NOF DEL DGT:00
NOF DEL DGT:00
NOF DEL DGT:01
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
4. Enter digits to be inserted.(e.g., 10288)
OR
Press Right Soft button to skip step or to
store information and advance to next step.
LCR MODIFY (005)
5. Enter digits to be appended.(e.g., 45678)
OR
Press Right Soft button to skip step or
to store information and return to step 2.
LCR MODIFY (005)
I:10288_
A:_
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 710
© SAMSUNG Electronics Co., Ltd.
LCR DIGIT TABLE
2-229
CHAPTER 2. MMC Programming
[714] DID NUMBER AND NAME TRANSLATION
Assigns an incoming DID call to a specific ring plan destination. It also provides a call
waiting option, if needed, so that a second incoming DID call can be received. The table is
also used to define which MOH source a caller to that DID number will hear when placed
on hold. An 11 character name can be added to the number. There are a maximum of 999
entries. If there is no matching number on DID service the call is routed to the operator
group.
Definitions of option are as follows:
Option
DGT
MOH SOURCE
Description
Digits to be received from Trunk line Up to 16 digits may be entered.
Allows the technician to select what the calling party will hear in regards to
that DID/DNIS number if the call is placed on hold. There are a total of 6
possible music selections(see below).
NONE
Follows the setting in MMC 408 for the trunk the call comes in on.
TONE
A repeated tone is played to the outside party.
INTERNAL CHIME
This is entered as the directory number of the music source on the
‘OLD FOLKS AT
MCP2(371).
HOME’
EXTERNAL DEVICE
Music Source or Digital announcer. This is entered as the directory
number of an external music source.
DIGITAL
This is entered as the directory number of the last AA port of an AA card.
ANNOUNCEMENT
For further details on using an AA port as an MOH source please see
ON AA CARD
MMC 739.
VOICE MAIL SOUND
If the system has an optional SVMi card installed, up to 100 custom
FILE
recorded sound files from the Voice Mail card can be used for MOH
sources. Select the SVMi port assigned in MMC 756. For information on
creating the sound files see SVMi System Administrator ManualRecording greeting by number. If you select this option be advised that
each VMMOH source requires a dedicated SVMi port/channel.
PRI
DID priority option. There are 9 priority levels: priority 1 is the highest
and priority 9 is the lowest.
When calls into station group come and group members are all busy, the
system will assign a priority to the DDI number so that calls from a high
priority DDI number will be placed at the front of the group queue.
If this option sets NO, the longest call that placed at the group queue has
the highest priority.
1: XXX, 2: XXX,
ring plan and destination during each ring plan. The destination can be a
3: XXX, 4: XXX,
station, station group, trunk or trunk group. If trunk or trunk group is
5: XXX, 6:XXX
selected the trunks must be programmed as E & M trunks to allow the
received digits to be re-sent on the facility(s). This is referred to as DID
Repeat digits over tie line.
An entry of the character ‘B’ means to repeat the received digits.
2-230
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Option
Description
CW
Call waiting Yes/No . Allow a second DID call to be received
MC
The number of maximum call count. When this sets 99, this feature will not
works. When this sets 0, if a call comes that matched DID digits and DGT field
then the system will be reject call. When this sets between 1 to 98, if a call
comes that matched DID digits and DGT field then the system counts same DID
digits call, and in case of the count is same or higher than this value, the system
sends busy signal to caller.
DC
The number of digits to delete. This is useful with Tandem switching,
mixed numbering plans and DID Repeat digits over tie line. Maximum
number of digits that can be deleted is 16.
NAME
Input up to 11 characters to identify call.
Refer to ‘MMC [104] STATION NAME’ for descriptions on INPUT
CHARACTERS.
CONDITIONS
If an E & M line is designated as FOLLOW DID TRANS at ‘MMC 416 ASSIGN E &
M/DID RINGDOWN’, calls are terminated according to the station direct dial translation
table of ‘MMC 714 DID NUMBER AND NAME TRANSLATION’.
DEFAULT DATA
INDEX
DIGIT
MOH
PRI
1-6
CW
MC
DC
NAME
001
2***
NONE
NO
B
N
99
0
NONE
002
3***
NONE
NO
B
N
99
0
NONE
003
5***
NONE
NO
B
N
99
0
NONE
004
8***
NONE
NO
B
N
99
0
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 714.
Display shows:
DID DIGIT
(001)
2. Enter valid index number(e.g., 005) via dial
keypad.
OR
Press Volume button to make selection and press
Right Soft button to move cursor.
DID DIGIT
(005)
3. Enter digits to be translated(e.g., 5065) via dial
keypad and press Right Soft button to move cursor.
DID DIGIT
(005)
© SAMSUNG Electronics Co., Ltd.
DGT:
DGT:
DGT:5065
2-231
CHAPTER 2. MMC Programming
4. Enter the MOH source for this entry.
OR
Press Volume button to select option and press
Right Soft button to return to step 3 above.
DID DIGIT
(005)
5. Enter priority level via dial keypad.(1-9 or NO)
OR
Press Volume button to make selection and
press Right Soft buttons to advance next step.
DID DIGIT
(005)
6. Enter station or group number for each Ring
Plan destination via dial keypad.(e.g., 530)
OR
Press Volume button to make selection and
press Right Soft button to advance next step.
DID DIGIT
7. Enter call wait option via dial keypad.
(1 for YES, 0 for NO)
OR
Press Volume button to make selection and
press Right Soft button to advance next step.
DID DIGIT
(005)
8. Enter maximum call count via dial keypad.
(00-99)
OR
Press Volume button to make selection and
press Right Soft button to advance next step.
DID DIGIT
(005)
9. Enter number or delete digit via dial keypad.
(0-16)
OR
Press Volume button to make selection and
press Right Soft button to advance next step.
DID DIGIT
(005)
DID DIGIT
(005)
10.
11.
Enter the name via dial keypad and press
Right Soft button to return to step 1.
MOH:NONE PRI:NO
MOH:NONE PRI:ÒO
1:530
(005)
2:
CW:N MC:99 DC:0
CW:N MC:99 DC:0
CW:N MC:99 DC:0
NAME:
Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
TRUNK PROGRAMMING
Refer to ‘RELATED ITEMS’ of MMC 411 ASSIGN E1 SIGNAL TYPE.
2-232
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[715] PROGRAMMED STATION MESSAGE
Allows custom messages to be programmed or default messages to be changed.
CONDITIONS
There are 15 messages in the system.
MESSAGES 01-10 are 16 character pre-programmed default messages. Any of them can
be changed.
MESSAGES 11-15 are 16 character blank messages that can be created.
INPUT CHARACTERS
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
DEFAULT DATA
TEN PROGRAMMED MESSAGES AS DETAILED BELOW
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
IN A MEETING
OUT ON A CALL
OUT TO LUNCH
LEAVE A MESSAGE
PAGE ME
OUT OF TOWN
IN TOMORROW
RETURN AFTERNOON
ON VACATION
GONE HOME
ACTION
DISPLAY
1. Press Transfer button and enter 715.
Display shows:
PGM.MESSAGE (01)
2. Enter index number.(e.g., 11)
OR
Press Volume button arrow to make selection
Press Right Soft button to move cursor.
PGM.MESSAGE (11)
3. Enter message via dial keypad using the above
Table.(maximum 16 characters)
Use A button to toggle upper case/lower case.
Press Right Soft button to return to step 2.
PGM.MESSAGE (11)
© SAMSUNG Electronics Co., Ltd.
IN A MEETING
_Blank Message
SunBathing
2-233
CHAPTER 2. MMC Programming
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 115
2-234
SET PROGRAMMED MESSAGE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[716] UK LCR OPTIONS
This MMC provides U.K. LCR options as described below.
No
Option
0
NETWORK CODE
Description
This table is used to network access code when the call is routed to
the secondary network. This table contains up to 16 entries. Each
code has 4 digits maximum in length and use option for None, CCC,
PIN or Both.(Default: all codes are empty and all use options are
none)
1
PIN CODE
0
NONE
1
CCC
2
PIN
3
BOTH
This code doesn’t use.
This code uses with Call Cast Code(CCC).
This code uses with PIN Code.
This code uses with PIN code and Call Cast Code.
This table is used to PIN code when the call is routed to the secondary
network. This table contains up to 4 entries and each code has 10
digits maximum in length.(Default: all tables are empty)
2
CCC OPTION
This is used to which number used for Call Cost Code.
(Default: Station Number)
3
STATION PIN NO.
0
STATION NUMBER
1
NONE Doesn’t use Call Cost Code.
Station number uses for Call Cost Code.
This is assigned to PIN code table number for each station
number.(Default: all stations are 1)
UK LCR OPTIONS
This MMC is available in Australia, New Zealand and U.K. only.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 716.
Display shows:
NETWORK CODE
2. Enter option number(0-3) via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
NETWORK CODE
© SAMSUNG Electronics Co., Ltd.
01:
01:
USE:NONE
USE:NONE
2-235
CHAPTER 2. MMC Programming
3. Enter entry number(01-16) via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
NETWORK CODE
4. Enter network access code via dial keypad
and press Right Soft button to move cursor.
NETWORK CODE
5. Enter use option number(0-3) via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to save and return step 3.
NETWORK CODE
01:
USE:NONE
01:1234 USE:NONE
01:1234 USE:CCC
6 Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 400
MMC 310
MMC 710
MMC 711
MMC 712
MMC 713
2-236
TENANT ON/OFF PER TRUNK
LCR CLASS OF SERVICE
LCR DIGIT TABLE
LCR TIME TABLE
LCR ROUTE TABLE
LCR MODIFY DIGIT TABLE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[717] UCD AGENT ID
This MMC defines UCD agent ID number or PIN numbers. These numbers are used to log
UCD agents into the UCD groups. There are 300 available entries on L system and 100
available entries on M system. Each entry is tied to a specific UCD group. Agent ID codes
can be up to 4 digits long.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 717.
Display shows:
AGENT PIN
(001)
2. Dial code index number.(e.g., 005)
OR
Press Volume buttons to select index number
and press Right Soft button to move cursor.
AGENT PIN
(005)
3. Enter ID code via dial keypad(e.g., 1234) and
press Right Soft button to move cursor.
AGENT PIN
(005)
4. Enter group number.(e.g., 505)
OR
Press Volume button to select group and
press Right Soft button to select and return to step 2.
OR
Press ANS/RLS button for all.
AGENT PIN
(005)
ID:
ID:_
GRP:NONE
GRP:NONE
ID:1234 GRP:NONE
ID:1234 GRP:505
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 607
© SAMSUNG Electronics Co., Ltd.
UCD OPTIONS
2-237
CHAPTER 2. MMC Programming
[718] MY AREA CODE
This MMC defines the home area code and country code. This information is used for
caller ID and ISDN calls in defining the area code on incoming calls. This MMC removes
the local area code to allow callback without digit modifications in LCR.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 718.
Display shows:
MY AREA CODE
2. Enter 0 for COUNTRY or 1 for AREA.
OR
Press Volume buttons to make selection and
press Right Soft button to move cursor.
MY AREA CODE
3. Enter area code(maximum 4 digits) via dial
keypad(e.g., 2) and press Right Soft button
to move cursor back to step 2.
MY AREA CODE
AREA
AREA
AREA
:
:
:2
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
TRUNK PROGRAMMING
Refer to ‘RELATED ITEMS’ of MMC 411 ASSIGN E1 SIGNAL TYPE.
2-238
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[719] IDLE DISPLAY
This program allows you to enter guidance data to be displayed on large LCD phones.
CONDITIONS
NONE
INPUT CHARACTERS
Use dial buttons to enter guidance data in English. Press a dial to display characters below
on LCD depending on the number of pressing the same dial. Press another dial to save the
displayed characters and move the cursor to the next character. Press [A] to change
uppercase/lowercase input modes.
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 719.
Display shows:
IDLE DISPLAY (01)
2. Press the location of the line of a large LCD
phone(01~12) on which guidance data is to be
displayed.
OR
Press Volume button to make selection and press
Right Soft button to move cursor.
IDLE DISPLAY (02)
3. Enter guidance data via dial keypad and press
Right Soft button to save and move to step 2.
IDLE DISPLAY (02)
WELCOME TO ABC
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 120
© SAMSUNG Electronics Co., Ltd.
LARGE LCD OPTION
2-239
CHAPTER 2. MMC Programming
[720] COPY KEY PROGRAMMING
Provides a tool for duplicating key assignment from one phone to another.
This can be done on a per-station basis or on all stations, but not on a group of stations.
One limitation is that the original and target phones must be of the same type(e.g., same
number of buttons).
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 720.
Display shows:
[201] COPY KEY
2. Enter the station number to copy.(e.g., 205)
OR
Press Volume buttons to make selection and
press Right Soft button to move cursor.
OR
Press ANS/RLS button for select all station.
[205] COPY KEY
3. Enter station number to copy from(e.g., 203)
and cursor returns to step 2.
OR
Press Volume buttons to make selection and
press Right Soft button to return to step 2.
[205] COPY KEY
FROM:NONE
FROM:NONE
FROM:203
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 107
MMC 721
MMC 722
MMC 723
2-240
KEY EXTENDER
SAVE STATION KEY PROGRAMMING
STATION KEY PROGRAMMING
SYSTEM KEY PROGRAMMING
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[721] SAVE STATION KEY PROGRAMMING
Provides a service tool which will minimize the accidental loss of programmable buttons
on the phones. The method of operation is simple, first the data is saved and then the
station can be replaced with another station type or the keys can be reprogrammed to other
features. Once testing or replacement is completed, the data can be restored to the
individual station, providing the same type is in place.
CONDITIONS
This program uses carefully. Because key programming data save to common key
programming database. When new phone connect, system copy from common key
programming database to new phone key programming database.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 721.
Display shows:
[201] SAVE KEY
2. Enter desired station number.(e.g., 205)
OR
Press Volume button to make selection and
press Right Soft button.
[205] SAVE KEY
3. Press Volume button to make function selection
and press Right Soft button to enter and return to
step 2.
[205] SAVE KEY
RESTORE
RESTORE
SAVE
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 107
MMC 722
MMC 723
© SAMSUNG Electronics Co., Ltd.
KEY EXTENDER
STATION KEY PROGRAMMING
SYSTEM KEY PROGRAMMING
2-241
CHAPTER 2. MMC Programming
[722] STATION KEY PROGRAMMING
Allows the customizing of programmable buttons on specific electronic phones, AOM, or
64 button module on the system. For phones, buttons 1 and 2 are set as CALL buttons by
default. For AOM’s and 64 button DSS box’s all buttons are set as DS keys by default.
Features are entered via dial pad keys by pressing the dial pad number the required number
of steps to select the feature. For example, for OHVA, the number 6 is pressed three times.
If the BOSS key is required, press 2 for the first letter B and then use the Volume button to
change the selection from BARGE to BOSS.
DIAL KEYPAD
COUNT
1
2
3
DIAL 2
AAPLAY
BARGE
CAD
DIAL 3
DGPALM
EP
FAUTO
DIAL 4
GCONF
HDSET
ICONF
DIAL 5
LANREQ
LANREQ
LANREQ
DIAL 6
MCID
NEW
OHVA
DIAL 7
PAGE
PAGE
RB
DIAL 8
TG
UA
VDIAL
DIAL 9
WAKEUP
XCHIN
WAKEUP
4
SETDND
WAKEUP
Programmable button Assignments:
Feature
AAPLAY
Description
AUTO ATTENDANT
Feature
Description
MCID
MALICIOUS CALL ID
MMPA
MEET ME PAGE ANSWER
PLAY(Requires AA card)
AAREC
AUTO ATTENDANT
RECORD(Requires AA card)
AB
ABSENCE
MMPG
MEET ME PAGE
ABAND
ABANDONED CALL
MS
MANUAL SIGNALING
ABW
AGENT BUSY/WRAP UP
MSG
MESSAGE
ACC
ACCOUNT
MUTE
MUTE
ALARM
ALARM
MW
MESSAGE WAIT
AN/RLS
ANSWER/RELEASE
NEW
NEW CALL
BARGE
BARGE-IN
NND
NAME NUMBER DATE
BILL
BILL(Related to Hotel/Motel
NOCLIP
NO CID SEND
NPG
NETWORK PAGE
Features)
BLOCK
2-242
OHVA BLOCK
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Feature
BOOTH
Description
BOOTH(Related to Hotel/Motel
Feature
Description
NS
NETWORK STATION
Features)
BOSS
BOSS/SECRETARY
NXT
CID NEXT
CAD
CALL ACTIVITY DISPLAY
OHVA
OFF-HOOK VOICE
ANNOUNCE
CALL
CALL BUTTON
OPER
OPERATOR
CAMP
STATION CAMP-ON
PAGE
PAGE
CANMG
MESSAGE CANCEL
PAGPK
PICKUP PAGE HOLD
CBK
CALLBACK
PARK
CALL PARK ORBIT
CC
CALL COVERAGE
PAUSE
PAUSE
CHIN
CHECK IN(Related to Hotel/Motel
PMSG
PROGRAMMED STATION
Features)
CHOUT
CHECK OUT(Related to
MESSAGE
PRB
Hotel/Motel Features)
CHOICE
CHOICE
PRIVACY RELEASE AND
BRIDGE
PROG
SET PROGRAM
PATH REPLACEMENT
(Related to News Server)
CID
CALLER ID
PTHR
CONF
CONFERENCE
RB
ROOM BILL
(Related to Hotel/Motel
Features)
CONP
CONNECTED NAME DISPLAY
REJECT
OHVA REJECT
CR
CALL RECORD
RETRY
AUTO REDIAL ON BUSY
REVW
REVIEW
(Requires SVMi card)
CREDIT
CREDIT(Related to Hotel/Motel
Features)
CS
CALL STATUS
RP
RING PLAN
CSNR
CALLER ID SAVE NUMBER
RSV
ROOM STATUS VIEW
REDIAL
(Related to Hotel/Motel
Features)
DGPALM
EASY ALARM SET TO REMOTE
RTO
RING PLAN TIME OVERRIDE
STATION
DICT
DICTATION
SETDND
SET DO NOT DISTURB
DIR
DIRECTORY
SETMG
SET MESSAGE W/O RING
DIVERT
EXECUTIVE CALL DIVERT TO
SG
STATION GROUP
SECRETARY
DLOCK
DOOR LOCK
SLOCAT
STAFF LOCATOR
(Related to Hotel/Motel
Features)
DN
DIALLED NUMBER
SNR
SAVED NUMBER REDIAL
DND
DO NOT DISTURB
SP
UCD SUPERVISOR
© SAMSUNG Electronics Co., Ltd.
2-243
CHAPTER 2. MMC Programming
Feature
Description
Feature
Description
DNDO
DO NOT DISTURB OVERRIDE
SPD
SPEED DIAL
DP
DIRECT PICKUP
SPKR
SPEAKER
DROP
CALL DROP
SSET
ISDN SUPPLEMENTARY SERVICE
SET
DS
DSS KEY
STATE
SET EXECUTIVE STATE
DT
DTS KEY
STORE
STORE DISPLAYED NUMBER
EP
ESTABLISHED CALL PICKUP
SETMG
SET MESSAGE W/O RING
EXTMIC
EXTERNAL MIC
SYSALM
SYSTEM ALARMS
FAUTO
FORCED AUTO ANSWER
TG
TRUNK GROUP
FLASH
FLASH
TIMER
TIMER
FWRD
CALL FORWARD
TP
TERMINAL PORTABILITY
GCONF
GROUP CONFERENCE
TRARPT
TRAFFIC REPORT
GPIK
GROUP PICKUP
TRSF
TRANSFER
HDSET
HEADSET MODE
UA
UNIVERSAL ANSWER
HLDPK
HOLD PICKUP
VDIAL
VOICE DIAL(Requires VDIAL card)
HOLD
HOLD
VG
VMS GROUP MESSAGE
(Requires SVM-800)
HOTEL
HOTEL(Related to Hotel/Motel
VM
Features)
ICONF
ISDN 3 PTY CONFERENCE
VOICE MAIL MEMO
(Requires SVMi card)
VMADM
VOICE MAIL ADMINISTRATION
(Requires SVMi card)
IDISC
ISDN 3 PTY DISCONNECTION
VMAME
ANSWER MACHINE
EMULATION(Requires SVMi card)
IG
IN/OUT GROUP
VMMSG
VOICE MAIL MESSAGE KEY
(Requires SVMi card)
INFDSP
INFORMATION DISPLAY
VMSCMT
VMS COMMENT(Requires SVM)
(Requires News/Call Plus)
INQIRE
INQUIRE
VMSMSG
VMS MESSAGE(Requires SVM)
IRET
ISDN 3 PTY RETRIEVE
VMSOUT
VMS OUT CALL(Requires SVM)
ISPY
CID SPY
VMSREC
VMS RECORD(Requires SVM)
LANREQ
LAN REQUEST
VMSVAC
VMS VACANT(Requires SVM)
LCR
LEAST COST ROUTING
VREC
VOICE RECORD(Requires VDIAL
card)
LISTN
GROUP LISTENING
VT
LNR
LAST NUMBER REDIAL
WAKEUP
VOICEMAIL TRANSFER
WAKE UP(Related to Hotel/Motel
Features)
LOG
CALL LOGGING
XCHIN
EXPRESS CHECK IN(Related to
Hotel/Motel Features)
2-244
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
CONDITIONS
NONE
DEFAULT DATA
<24 Button Digital Phone>
CALL1
CALL1
CALL2
CALL1
DT701
CALL1
DT702
CALL1
DT703
CALL1
DT704
CALL1
DT705
CALL1
DT706
CALL1
DT7017
CALL1
DT708
CALL1
DT709
CALL1
DT7010
CALL1
DT711
CALL1
DT712
CALL1
DT713
CALL1
DT714
CALL1
DT715
CALL1
DT716
CALL1
CONF
CALL1
SPD
CALL1
NONE
CALL1
PAGE
CALL1
CBK
CALL1
GPIK01
CALL1
48 Button AOM
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
DS
CALL1
© SAMSUNG Electronics Co., Ltd.
2-245
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 722.
Display shows:
[201] KEY (MAST)
2. Enter selected station number.(e.g., 205)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
[205] KEY (MAST)
3. Enter selected key number.(e.g., 18)
OR
Press Volume button to select key number and
press Right Soft button to move cursor.
[201] KEY (MAST)
4. Using above chart, press dial pad key number
to make selection.
OR
Press Volume button to make selection and
press Right Soft button to advance cursor to step 5
to enter extender if required or to return to step 2.
[201] KEY PROG.
5. If required, enter extender.(e.g.,03)
OR
Press Volume button to make selection and
press Right Soft button to return to step 2.
[201] KEY PROG.
01:CALL1
01:CALL1
18:NONE _
18:NONE GPIK_
18:NONE GPIK03
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 107
MMC 720
MMC 721
2-246
KEY EXTENDER
COPY KEY PROGRAMMING
SAVE STATION KEY PROGRAMMING
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[723] SYSTEM KEY PROGRAMMING
This MMC is much like MMC 722, Station Key Programming. The main difference is that
this MMC is system-wide rather than on a per-station basis. Features are entered via the
dial keypad by pressing numbers as shown in the table. For example, for OHVA the
number 6 is pressed three times. If the BOSS key is required, press 2 for the first letter B,
and then use the Volume button to change selection from BARGE to BOSS.
TYPE OF PHONE
No
Type of Phone
Description
00
24 BTN SETS
Phone with 24 program buttons
01
12 BTN SETS
Phone with 12 program buttons
02
US 7B SETS
US phone with 7 program buttons
03
EU 6B SETS
EU phone with 6 program buttons
05
40-64B AOMS
AOM with 40-64 program buttons
06
20 BTN SETS
Phone with 20 program buttons
07
28 BTN SETS
Phone with 28 program buttons
08
18 BTN SETS
Phone with 18 program buttons
09
8 BTN SETS
Phone with 8 program buttons
10
99 BTN SETS
Phone with 99 program buttons
11
38 BTN SETS
Phone with 38 program buttons
12
21 BTN SETS
Phone with 21 program buttons
13
14 BTN SETS
Phone with 14 program buttons
14
DS-07S SETS
DS phone with 7 program buttons
DIAL KEYPAD
COUNT
1
2
3
DIAL 2
AAPLAY
BARGE
CAD
DIAL 3
DGPALM
EP
FAUTO
DIAL 4
GCONF
HDSET
ICONF
DIAL 5
LANREQ
LANREQ
LANREQ
DIAL 6
MCID
NEW
OHVA
DIAL 7
PAGE
PAGE
RB
DIAL 8
TG
UA
VDIAL
DIAL 9
WAKEUP
XCHIN
WAKEUP
4
SETDND
WAKEUP
See Programmable button Assignments on MMC 722.
© SAMSUNG Electronics Co., Ltd.
2-247
CHAPTER 2. MMC Programming
CONDITIONS
NONE
DEFAULT DATA
SEE DEFAULT DATA ON MMC 722
ACTION
DISPLAY
1. Press Transfer button and enter 723.
Display shows:
TYPE:24 BTN SETS
2. Enter type of set via dial keypad.(e.g.,1)
OR
Press Volume button to make selection and
press Right Soft button.
TYPE:12 BTN SETS
3. Enter key number.(e.g., 03)
OR
Press Volume button to make selection and
press Right Soft button.
TYPE:12 BTN SETS
4. Using table above, press dial keypad number to
make selection.
OR
Press Volume button to make selection and
press Right Soft button to advance cursor to
step 5 to enter extender, if required.
OR
Press Left Soft button to return to step 3.
TYPE:12 BTN SETS
5. If required, enter extender.(e.g.,03)
OR
Press Volume button to make selection and
press Right Soft button to return to step 2.
TYPE:12 BTN SETS
01:CALL1
01:CALL1
03:NONE
03:NONE GPIK
03:GPIK GPIK03
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 107
MMC 720
MMC 721
2-248
KEY EXTENDER
COPY KEY PROGRAMMING
SAVE STATION KEY PROGRAMMING
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[724] DIAL NUMBERING PLAN
This MMC allows the technician to change directory numbers for stations, trunks, station
groups, trunk groups and feature access codes. The system can be pre-programmed with a
default three or four digit numbering for station, station groups and trunk numbers
depending on the position of the DIP switches on the MCP2 card. There is an error
message provided to prevent the accidental duplication of a directory number or feature
access code.
No
00
Type of Dial No
STN DIAL NO.
Description
This is where station directory numbers are changed or assigned.
Default: 201-2xx, 3xx(last 319) or 2001-2xxx
01
TRK DIAL NO.
This is where trunk directory numbers are changed or assigned.
Default: 701-7xx or 7001-7xxx
02
AA/VD DIAL NO.
This is where AA port or Voice Dial port directory numbers are
changed or assigned.
Default: AA ports: 3951-39xx
VD ports: 3981-398x
03
MISC DIAL NO.
This is where directory numbers for relays, MOH ports and the
alarm sensor are changed or assigned.
Default: Internal CHIME: 371
Internal MODEM: 3999
External MOH: 372-377
External PAGE & Relay: 361-369
Common Bell Relay: 3991-3993
Loud Bell Relay: 3995-3997
04
05
06
STNG DIAL
This is where station group numbers are changed or assigned.
NUMBER
Default: 500-5xx or 5001-5xxx
TRKG DIAL
This is where trunk group numbers are changed or assigned.
NUMBER
Default: The first is 9 or 0, 800-828
FEAT DIAL NUMBER
This is where feature access codes are changed or assigned.
Dialling codes are entered via the dial pad key by pressing the dial
pad number the required steps to select the feature. For example,
for OHVA, the number 6 would be pressed three times.
NOTE) Please remember that this program is system-wide.
07
S0 STN DIAL NO.
This is where directory numbers for BRI station ports mapping
terminal number.
Default: 8701-8748
08
DECT STN DIAL NO.
This is where directory numbers for DECT terminals.
Default: 8801-8899
09
NTWK LCR DIAL NO.
This is where additional LCR access codes are entered in the case
when two or more OfficeServ 500 system are networked together.
Default: NONE
© SAMSUNG Electronics Co., Ltd.
2-249
CHAPTER 2. MMC Programming
No
10
Type of Dial No
VIRT EXT DIAL NO.
Description
This is where virtual station directory numbers are
changed or assigned.
Default: SLT: 3501-3546, DGP: 3401-3480
11
MGI DIAL NO.
This is where MGI port directory numbers are changed or
assigned.
Default: 3801-38xx
12
IP STN DIAL NO.
This is where IP-based station directory numbers are
changed or assigned.
Default: 3201-3299(DESKTOP PHONE), 33013399(MOBILE PHONE)
14
VOIP NET DIAL NO.
This is where Samsung proprietary switch-to-switch VoIP
networking trunk signaling port directory numbers are
changed or assigned.
Default: 8301-8380
15
H323 TRK DIAL NO.
This is where VoIP H.323 trunk signaling port directory
numbers are changed or assigned.
Default: 8401-8480
16
SIP TRK DIAL NO.
This is where VoIP SIP trunk signaling port directory
numbers are changed or assigned.
Default: 8501-8580
FEATURE NUMBERING DIAL KEYPAD
COUNT
2-250
1
2
3
DIAL 2
ABAND
BARGE
CAMP
DIAL 3
DGPALM
DGPALM
FAUTO
DIAL 4
GCONF
HDSET
IG
DIAL 5
LCR
LCR
LCR
DIAL 6
MCID
NEW
OHVA
DIAL 7
PAGE
PAGE
RB
DIAL 8
UA
UA
VDIAL
DIAL 9
WAKEUP
WAKEUP
WAKEUP
4
SELFID
WAKEUP
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Feature Code Assignments and Default
Feature
Default
Description
ABAND
64
ABANDONED CALL
ABS
NONE
ABSENCE
ABW
NONE
AGENT BUSY/WRAP UP
ACCT
47
ACCOUNT
ALLCLR
NONE
ALL CLEAR
ALMCLR
57
ALARM
AUTH
*
AUTHORIZATION CODE
BARGE
NONE
BARGE-IN
BILL
NONE
BILL(Related to Hotel/Motel Features)
BLOCK
NONE
OHVA BLOCK
BOSS
NONE
BOSS/SECRETARY
CAMP
45
STATION CAMP-ON
CANMG
42
MESSAGE CANCEL
CBK
44
CALLBACK
CHIN
NONE
CHECK IN(Related to Hotel/Motel Features)
CHOUT
NONE
CHECK OUT(Related to Hotel/Motel Features)
CHOICE
NONE
CHOICE(Related to News Server)
CONF
46
CONFERENCE
CONP
NONE
CONNECTED NAME DISPLAY
CR
NONE
CALL RECORD(Requires SVMi card)
CREDIT
NONE
CREDIT(Related to Hotel/Motel Features)
DGPALM
NONE
EASY ALARM SET TO REMOTE STATION
DICT
NONE
DICTATION
DIR
NONE
DIRECTORY
DIRPK
65
DIRECT PICKUP
DISALM
58
DISA ALARM CLEAR
DIVERT
NONE
EXECUTIVE CALL DIVERT TO SECRETARY
DLOCK
13
DOOR UNLOCK
DND
40
DO NOT DISTURB
DNDO
NONE
DO NOT DISTURB OVERRIDE
FAUTO
14
FORCED AUTO ANSWER
FLASH
49
FLASH
FWD
60
CALL FORWARD
GCONF
NONE
GROUP CONFERENCE
GRPK
66
GROUP PICKUP
© SAMSUNG Electronics Co., Ltd.
2-251
CHAPTER 2. MMC Programming
Feature
Default
HDSET
NONE
HEADSET MODE
HLDPK
12
HOLD PICKUP
HOLD
11
HOLD
HOTEL
NONE
HOTEL(Related to Hotel/Motel Features)
IG
NONE
IN/OUT GROUP
INFDSP
NONE
INFORMATION DISPLAY(Requires News/Call Plus)
LCR
NONE
LEAST COST ROUTING
LISTN
NONE
GROUP LISTENING
LNR
19
LAST NUMBER REDIAL
LOG
NONE
CALL LOGGING
MCID
NONE
MALICIOUS CALL ID
MMPA
56
MEET ME PAGE ANSWER
MMPG
54
MEET ME PAGE
MSG
43
MESSAGE
MYGRPK
NONE
MY PICKUP GROUP CALL PICKUP
NEW
NONE
NEW CALL
NOCLIP
NONE
NO CID SEND
NPAGE
NONE
NETWORK PAGE
OHVA
NONE
OFF-HOOK VOICE ANNOUNCE
OPER
0
OPERATOR
PAGE
55
PAGE
PAGPK
10
PICKUP PAGE HOLD
PARK
NONE
CALL PARK ORBIT
PMSG
48
PROGRAMMED STATION MESSAGE
PTHR
NONE
PATH REPLACEMENT
RB
NONE
ROOM BILL(Related to Hotel/Motel Features)
REJECT
NONE
OHVA REJECT
RP
NONE
RING PLAN
RSV
NONE
ROOM STATUS VIEW(Related to Hotel/Motel Features)
RTO
NONE
RING PLAN TIME OVERRIDE
SELPID
NONE
SELF SYSTEM ID
SETMG
41
SET MESSAGE W/O RING
SLOCAT
NONE
STAFF LOCATOR(Related to Hotel/Motel Features)
SLTALM
SLTMMC
2-252
Description
EASY ALARM SET TO SELF STATION
15
NORMAL PHONE PROGRAMMING
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Feature
Default
Description
SNR
17
SAVED NUMBER REDIAL
SPEED
16
SPEED DIAL
SRELOC
NONE
SET RELOCATION
STATE
NONE
SET EXECUTIVE STATE
UA
NONE
UNIVERSAL ANSWER
VDIAL
681
VOICE DIAL(Requires VDIAL card)
VMADM
NONE
VOICE MAIL ADMINISTRATION(Requires SVMi card)
VMAME
NONE
ANSWER MACHINE EMULATION(Requires SVMi card)
VMMEMO
#
VOICE MAIL MEMO(Requires SVMi card)
VMMSG
NONE
VOICE MAIL MESSAGE KEY(Requires SVMi card)
VMSCMT
NONE
VMS COMMENT(Requires SVM -800)
VMSMSG
NONE
VMS MESSAGE(Requires SVM -800)
VMSOUT
NONE
VMS OUT CALL(Requires SVM -800)
VMSREC
NONE
VMS RECORD(Requires SVM -800)
VMSVAC
NONE
VMS VACANT(Requires SVM -800)
VREC
682
VOICE RECORD(Requires VDIAL card)
WAKEUP
18
WAKE UP(Related to Hotel/Motel Features)
WCOS
59
WORKING CLASS OF SERVICE
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
FEATURE CODES ARE DEPEND ON COUNTRY
© SAMSUNG Electronics Co., Ltd.
2-253
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 723.
Display shows:
STN DIAL NUM:C1
2. Dial option number to make selection.(e. g., 06)
OR
Press Volume button to make selection and
press Right Soft button to advance cursor.
FEAT DIAL NUMBER
3. Dial first letter of feature name.(e. g., 7)
AND
Press Volume button to make selection then
press Right Soft button to advance cursor.
FEAT NUMBER PLAN
4. Enter digits(e.g., 63) via the dial keypad.
FEAT NUMBER PLAN
S2-P01:201
ABAND :64 _
PAGE :55
FEAT NUMBER PLAN
PARK :NONE _
PARK :NONE 63
5. Press Right Soft button to enter change and
continue to make changes.
If an error message appears indicating duplication
of access code, enter 1 for YES for change
or enter 0 for NO for no change.
FEAT NUMBER PLAN
PARK :NONE 63
SAME DIAL EXIST
CHANGE? Y:1,N:0
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
ALL MMC
2-254
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[725] SMDR OPTIONS
Allows the system administrator to select the information printed on the SMDR report.
The following options may be selected to print on SMDR:
No
00
Option
PAGE HEADER
Default
YES
Description
This option determines whether a page header will print
at the top of each page. This would normally be turned
off if SMDR is being sent to a Call Accounting machine.
01
LINE PER PAGE
60
This option selects the length of each page to determine
when to print the SMDR header. The number of lines
may be in the range 01-99.
02
INCOMING CALL
NO
This option determines whether incoming calls will print
on SMDR.
03
OUTGOING CALL
YES
This option determines whether outgoing calls will print
on SMDR.
04
AUTHORIZE
NO
CODE
This option determines whether authorization codes will
print on SMDR. If this option is set to NO, system make
AUTH field to ‘****’ on SMDR.
05
SMDR START
YES
TIME
06
IN/OUT GROUP
This option determines whether valid calls will include
the minimum call time in total call duration.
NO
This option allows a message, IN GROUP or OUT
GROUP, to be printed in the digits dialled column each
time a station enters or leaves a group.
07
DND CALL
NO
This option allows a message, IN DND or OUT DND, to
be printed in the digits dialled column each time a
station enters or leaves DND.
08
WAKE-UP CALL
YES
This option determines whether stations receiving an
alarm reminder call will print on SMDR.
09
DIRECTORY
NONE
NAME
This option allows the system administrator to enter a
16 character name which will appear on the SMDR
header.
10
CALLER ID DATA
YES
This option can be selected to print Caller ID data
received from the Central Office on incoming calls.
This option requires the use of a 132 column(wide carriage)
printer or an 80 column printer set for condensed print.
11
ABANDON CALL
YES
If this option is set to YES, unanswered calls for which
CID information was received will print on SMDR.
13
NO. OF DIAL
MASK
0
If this option is set to a numeric value, the selected last
digits of the number dialled field will be masked as
asterisks(*) on the SMDR print out. Maximum masked
digits is 18. First 4 digits will not mask.
© SAMSUNG Electronics Co., Ltd.
2-255
CHAPTER 2. MMC Programming
No
15
Option
INCOMING
Default
NO
ANSWER
16
INTERCOM CALL
Description
If this option is set to YES, the duration of calls ringing
before answered will print on SMDR.
NO
This option determines whether intercom calls will print
on SMDR.
17
KEY MMC IN/OUT
NO
If set to YES then the SMDR record will show
programming being opened and closed in MMC 200 and
MMC 800.
20
HOTEL PAGE
END
FEED
21
HOTEL START
This option determines where the page feed is inserted
on HM REPT.(Hotel/Model Enabled Only)
0
LINE
This option determines that the number of empty lines
per each page on HM REPT.(Hotel/Model Enabled
Only)
23
DID NUM/NAME
YES
If this option is set to YES, received DID information will
print on SMDR.
24
ITP
NO
REGISTRATION
25
SET
RELOCATION
If set to YES then the SMDR record will show IP-based
station to system connect and disconnect.
NO
If set to YES then the SMDR record will show set
relocated information.
CONDITIONS
NONE
INPUT CHARACTERS
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
DEFAULT DATA
SEE DESCRIPTION
SOME OPTIONS ARE DEPEND ON COUNTRY
2-256
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
ACTION
DISPLAY
1. Press Transfer button and enter 725.
Display shows:
PAGE HEADER
2. Dial the option number.(e.g., 01)
OR
Use the Volume buttons to scroll through
the options and press Right Soft button to
select an option.
LINE PER PAGE
3. Enter the option data.
OR
LINE PER PAGE
Use the Volume buttons to press Right Soft
button to save the data and return to step 2.
PRINT: YES
60 LINE/PAGE
50 LINE/PAGE
LINE PER PAGE
50 LINE/PAGE
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 300
© SAMSUNG Electronics Co., Ltd.
CUSTOMER ON/OFF PER STATION
2-257
CHAPTER 2. MMC Programming
[726] VM/AA OPTIONS
This MMC is used to define all the in band DTMF codes sent to voice mail ports. These in
band codes can be 0-9, A, B or C, and performed two functions.
CALL AND TYPE INFORMATION
This is a DTMF signaling string sent to a voice mail port when the voice mail port answers
a call. This DTMF information tells the voice mail port what type of call it is receiving and
where the call is coming from. e.g., call has forwarded from extension 225
CALL PROGRESS TONES
These are sent to the voice mail system to provide information about the progress of the
call. e.g., ring back, busy or disconnect.
Most Voice Mail systems can utilize DTMF in band signaling for more efficient call
processing. This MMC has many parameters that can be programmed according to the type
of automated attendant and/or voice mail system connected.
CALL and TYPE INFORMATION
The format of the DTMF data sent to a VM/AA port is as follows:
[CALL TYPE] + [DN1] + [SEPARATOR] + [DN2]
an example of this would be
[FORWARD ALL ] from [ 225 ] on trunk [ 703 ]
Each field can be programmed individually as follows:
Field
Description
Default
EXTENSION
If set to yes, when the voice mail auto attendant system answers
FOR DN1
a call the system will send data in the DN1 field indicating that a
No
station is ringing the VMAA port.
If set to no, when the voice mail auto attendant system answers
a call the system will not send station data in the DN1 field.
TRUNK FOR DN1
If set to yes, when the voice mail auto attendant system answers
No
a call the system will send data in the DN1 field indicating that a
trunk is ringing the VMAA port.
If set to no, when the voice mail auto attendant system answers
a call the system will not send trunk data in the DN1 field.
EXTENSION
If set to yes, when the voice mail auto attendant system answers
FOR DN2
a call the system will send data in the DN2 field indicating the
No
originating station of the call ringing the VMAA port.
If set to no, when the voice mail auto attendant system answers
a call the system will not send station data in the DN2 field.
2-258
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Field
TRUNK FOR DN2
Description
If set to yes, when the voice mail auto attendant system answers
Default
No
a call the system will send data in the DN2 field indicating the
originating trunk of the call ringing the VMAA port.
If set to no, when the voice mail auto attendant system answers
a call the system will not send trunk data in the DN2 field
SEPARATOR
When both DN1 and DN2 are used, a digit defined here is sent
No
between DN1 and DN2 so the VMAA system can determine
where DN 1 stops and where DN 2 starts. The separator can be
DTMF 0 through 9, *, #, A, B or C.
DISCONNECT
This is the call progress digit sent to the VMAA port in place of a
SIGNAL
disconnect open. The digit defined here is sent three times.
CALLER ID
If set to yes, when the voice mail auto attendant system answers
NUMBER
a call the system will send Caller ID data as DTMF tones to the
C
No
VMAA port.
CALL TYPE ID
This is the DTMF digit that is sent first in the in band digit string
and can identify any of the following call types
No
0
1
Call Type
Description
DIRECT
A call originating directly from another
CALL
station in the system.
ALL FWD
This indicates that a call was forwarded to
CALL
the VM/AA port from a station with CALL
Default
1
2
FORWARD ALL set.
2
BSY FWD
This indicates that a call was forwarded to
CALL
the VM/AA port from a station with CALL
3
FORWARD BUSY set.
3
NOA FWD
This indicates that a call was forwarded to
CALL
the VM/AA port from a station with CALL
4
FORWARD NO ANSWER set.
4
RECALL
A call is recalling the VM/AA port after
5
being transferred and not answered.
5
DIR TRK
A Trunk Line call has gone directly to
CALL
VM/AA
6
(e.g., trunk 717 DIL to VM/AA).
6
OVERFLOW
A call has OVERFLOWED to the VM/AA
7
port from a station group.
7
DID CALL
A DID call has called the VM/AA port.
8
8
MESSAGE
A message button or message reply
9
CALL
feature code has been used to call the
VM/AA port.
© SAMSUNG Electronics Co., Ltd.
2-259
CHAPTER 2. MMC Programming
Field
Description
Default
PROGRESS
These are the DTMF codes that is sent to the VMAA port in place
TONE ID
of regular progress tones. For example, when a VMAA port goes
off hook to originate or transfer a call, instead of hearing normal
dial tone, it will hear DTMF ‘BA’. Progress tones can greatly
increase the efficiency of a VMAA system because it is easier
and quicker to detect DTMF than a busy, ring back or DND tone.
Progress tones can identify any of the following.
No
Call Type
Description
Default
0
DIAL TONE
Dial Tone
NO
1
BUSY TONE
Busy Tone
NO
2
RINGBAK TONE
Ringback Tone
NO
3
DND NO MORE
DND or No More Call Button Error
NO
4
HDSET ANSWER
Off Hook Answer
NO
5
SPKER ANSWER
On Hook Answer
NO
GENERAL RULES
2-260
1.
201 is talking to a trunk and presses TRANSFER plus the station number, but the
station is forwarded to VM/AA and VM/AA answers. When this happens, if 201
presses TRANSFER again to return to the trunk, the VM/AA port is not on hold. It is
disconnected.
2.
A VM/AA port leaves a message indication for a station. When the station returns the
message, any available port in the VM/AA group should ring, not only the one that left
the message.
3.
A VM/AA port leaves a message for a station. When the station returns the message,
the MESSAGE LED is not automatically turned off. If a VM/AA system turns on the
MESSAGE LED, the VM/AA system must turn it off.
4.
If DTMF call progress tones are not enabled, the system sends regular call progress
tones.
5.
When a VM/AA port calls a station that is in the AUTO ANSWER or VOICE
ANNOUNCE mode, the phone will be forced to ring.
6.
All calls to a VM/AA port or group ring with Trunk line ringing cadence, not intercom
ring cadence.
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
EXAMPLES OF VM/AA OPERATION(IN BAND DTMF DIGIT STRING)
In the following example, all call and type data is turned on unless otherwise stated. X is
the separator digit, all-default values are used in these examples and [
] is not used.
A DIL 701 calls a VM/AA port or group:
[*] + [701] + [ ] + [
]
In the above example, if Trunk Line information is not used:
[
]+[
]+[
]+[
](Nothing is used)
DIL 701 calls a call-forwarded station(205):
[#] + [205] + [X] + [701]
In the above example, if forward information is not used:
[
] + [205] + [X] + [701]
In the above example, if forward and DN2/Trunk Line information is not used:
[
] + [205] + [
]+[
]
DIL 701 calls group 501 that overflows to VM/AA:
[#] + [501] + [x] + [701]
In the above example, if overflow information is turned off:
[
]+[
]+[
]+[
](Nothing is sent)
A DID call rings the VM/AA directly:
[B] + [9999] + [ ] + [ ]
9999 are the DID digits from Trunk Line
In the above example, if did information is turned off:
[
] + [9999] + [
]+[
]
A station transfers(blind or screened) a call(Trunk Line, DID or intercom) to VM/AA group
or port. When the transferring station hangs up(blind transfer):
[
]+[
]+[
]+[
](Nothing is sent)
A station(202) transfers a Trunk Line call(702) to a station(225) that is Call Forward All to
a VM/AA group or port. When the transferring station hangs up(blind transfer) and the
VM/AA group or port answers:
[#] + [225] + [x] + [702]
A station(202) transfers a Trunk Line call(702) to a group(501) that overflows to a VM/AA
group or port:
[#] + [501] + [X] + [702]
© SAMSUNG Electronics Co., Ltd.
2-261
CHAPTER 2. MMC Programming
In the above example, if overflow information is turned off:
[
]+[
]+[
]+[
](Nothing is sent)
A station(205) calls a VM/AA port or group:
[Q] + [205] + [
]+[
]
In the above example, if direct information is turned off:
[
]+[
]+[
]+[
](Nothing is sent)
A station(205) calls using MESSAGE key:
[Q] + [205] + [
]+[
]
In the above example, if message information is turned off:
[
]+[
]+[
]+[
](Nothing is sent)
A call(702) recalls back from station 225 to the VM/AA group:
[#] + [225] + [x] + [702]
In the above example, if recall and DN2/CO information are turned off:
[
]+[
]+[
]+[
](Nothing is sent)
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
SOME OPTIONS ARE DEPEND ON COUNTRY
PROGRAM BUTTONS
A
B
C
2-262
Used to input alpha character ‘A’
Used to insert alpha character ‘B’
Used to insert alpha character ‘C’
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
ACTION
DISPLAY
1. Press Transfer button and enter 726.
Display shows:
EXT FOR DN1
2. Enter the OPTION number from the above list.
(e.g., 3)
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
TRK FOR DN2
3. Enter 1 for YES or 0 for NO.
OR
Press Volume button for selection and press
Right Soft button to return to step 2.
TRK FOR DN2
YES
NO
YES
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 207
© SAMSUNG Electronics Co., Ltd.
ASSIGN VM/AA PORT
2-263
CHAPTER 2. MMC Programming
[727] SYSTEM VERSION DISPLAY
This MMC is only used for system version display. This is a READ ONLY MMC.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 727.
Display shows:
MCP VERSION
‘03.07.01 L2.03
2. Press Volume button to select other Card versions.
DLI CARD
Cabinet and Slot shown:
C1-S2:8 DLI
TEPRI CARD PRI MODE
Cabinet and Slot shown:
C2-S1:TEPRI/EP
AUTO ATTENDANT CARD
Cabinet and Slot shown:
C1-S8:AA
NO VERSION DATA
‘01.08.14 V1.02
‘00.09.19 1.00
3. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-264
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[728] CID TRANSLATION TABLE
Allows the system administrator or technician to associate a CID number received from the
central office with a name programmed in this translation table. If there is no match
between a received number and a name in this table, ‘no CID name’ will be displayed.
The translation table consists of 1000 entries for a M system and 2000 for a L system. Each
entry is comprised of a ten-digit(14 digits allowed) telephone number and a 16-digit name.
CONDITIONS
NONE
INPUT CHARACTERS
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 728.
Display shows first entry:
TRANSLATIO(0001)
2. Dial entry number.(e.g., 0005)
OR
Use Volume button to scroll through entries
and press Right Soft button to select entry.
TRANSLATIO(0005)
3. Enter telephone number and press Right Soft
button to advance name entry.
OR
Enter telephone number and press Left Soft
button to return to step 2.
TRANSLATIO(0005)
4. Enter associated name as described above
and press Right Soft button to return to step 2.
TRANSLATIO(0005)
DGT:
DGT:_
DGT:3054264100
SAMSUNG TELECOM
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 312
MMC 608
© SAMSUNG Electronics Co., Ltd.
ALLOW CID
ASSIGN REVIEW BLOCKS
2-265
CHAPTER 2. MMC Programming
[730] AA RECORD GAIN
This program is used for adjusting the gain when recording(REC) or playing(PL) on a
built-in auto attendant card.
The adjustments can be made as follows:
Adjustment
No
Description
0
0. +0.0
No adjustment
1
1. +1.9
Up 1.9 dB
2
2. -6.0
Down 6.0 dB
3
3. -2.5
Down 2.5 dB
CONDITIONS
NONE
DEFAULT DATA
0 dB
ACTION
DISPLAY
1. Press Transfer button and enter 730.
Display shows:
[3951]AA GAIN
2. Dial AA number.(e.g., 3959)
OR
Press Volume button to make selection and
press Right Soft button.
[3959]AA GAIN
3. Press Volume button to select record gain and
press Right Soft button.
[3959]AA GAIN
4. Press Volume button to select play gain and
press Right Soft button.
[3959]AA GAIN
REC:+0.0 PL:+0.0
REC:+0.0 PL:+0.0
REC:+1.9 PL:+0.0
REC:+1.9 PL:+0.0
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-266
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[731] AA RAM CLEAR
Used for making clear AA RAM on a per-AA card basis. Through this MMC,
the system only accepts the first port as a port field and LCD shows its selection.
This will erase the whole message that has been programmed previously on the selected
card.
CONDITIONS
This will erase the whole message that has been programmed previously on the
selected card.
If the system or card is restarted during a recording or right after a recording while the
memory was being rearranged(displays BUSY when played), the memory must be
erased before recording again.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 731.
Display shows:
[3951]RAM CLEAR
2. Dial AA number.(e.g., 3951)
OR
Press Volume button to make selection and
press Right Soft button.
[3951]RAM CLEAR
3. Dial 0(No) or 1(Yes).
OR
Press Volume button to make selection and press
Right Soft button.
[3951]RAM CLEAR
4. Dial 0(No) or 1(Yes) to confirm selection.
OR
Press Volume button to make selection and press
Right Soft button.
[3951]RAM CLEAR
CLR RECORDED?NO
CLR RECORDED?NO
CLR RECORDED?YES
ARE YOU SURE?NO
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-267
CHAPTER 2. MMC Programming
[732] AA TRANSLATION TABLE
AA translation tables are responsible for routing calls based on digits dialled.
There are 12 translation tables available. Each table can be assigned to one or more plans in
MMC 733 Auto Attendant Plan Programming. A translation table consists of a number of
100 entries. Each entry number has two fields to program: the first field is for the digits
received by the caller and the second field is for the destination or action.
The destination field can be a station number, station group or another plan. Plans are
entered by pressing special key A plus two digits 01-12. If a voice mail group is entered,
the call will be transferred to the voice mail system with the appropriate in band digit
packet to indicate a Forward All call from the station number dialled by the caller.
The digits defined in the first field of this MMC [dialled digits] must be a valid station
number.
If the digits programmed as a destination are a voice mail port the voice mail port will
receive an in band packet of DTMF equal to [FWD from EXTENSION NUMBER
DIALLED].
There are a number of special characters that are used in translation tables.
They are as follows:
* = Used to represent any digit.
P = (Special Key A) Plan. Used to assign a plan as a destination(P01-P12).
B = (Special Key B) Buffer. When used in the destination field, transfers the call to the
same extension as the digits dialled by the caller.
C = (Special Key C) Change greeting or Ring Plan.
S = (Special Key E) System Speed Dial Number. Used to assign a System Speed Dial
number as a destination.
2-268
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
DESTINATION:
Consider the following entry examples.
Digits
Dest
Comments
0
0
Caller will be transferred to 0.
2**
B
If a caller dials any three digit extension number beginning with 2, the call
will be transferred to the extension number dialled.
48#2
C
If a caller dials 48#2, the current plan’s greeting may be changed. 48#2 is
essentially a special passcode for changing the current greeting or ring
plan.
1
526
If a caller dials 1, the call will be transferred to group 526.
5
P08
If a caller dials 5, the call will be transferred to plan 08.
Number conflicts like 2 and 23 or 56 and 567 are allowed in translation table
programming. In these cases, the system will compare received digits from AA
card after AA TRANS time and transfer to the proper destination.
Entries in the translation table will also provide the following features which are useful if a
mailbox owner does not have a telephone on the system, but does have a SVMi voice
mailbox.
If a caller dials # + nnn he will leave a message directly in the mailbox specified in the
destination.
If a caller dials * + nnn he will log into the mailbox specified in the destination.
If the translation table contains an entry like nnn = D(D is selected using the fourth Soft
button) callers dialling nnn will leave a message directly in the mailbox specified in the
destination.
NOTES ABOUT CHANGING RING PLANS AND ALTERNATE GREETING:
MANUAL SERVICE
1.
When the phone system changes ring plans, the AA greetings will also change as
programmed in MMC 733.
2.
When the AA alternate greeting passcode is entered the caller may input a digit to
change the ring plan. This means that a customer who wants to put the system in a
different ring plan can call in remotely and do it.
© SAMSUNG Electronics Co., Ltd.
2-269
CHAPTER 2. MMC Programming
3.
When the alternate greeting passcode is entered, the system will allow to select a ring
plan. If a RP(ring plan) key is programmed on the system it will FLASH.
The normal status of this light in a ring plan is on steady. A flashing RP key
corresponding to the ring plan indicates the remote ring plan has been set. If a RTO
key is available it will also flash.
4.
If the alternate greeting is not activated but the ring plan is changed the system will
remain in the selected ring plan until the next scheduled ring plan change.
If the alternate greeting is activated the system will remain in the existing ring plan or
the selected ring plan until the alternate greeting is manually deactivated.
5. To implement ring plan changes and /or the alternate greeting the caller must enter the
number or ‘passcode’ that implements the special key program. After the passcode is
entered the caller must enter 2 digits. The first digit selects the desired ring plan to
change to(1-6) or 0 for no change. The second digit activates the alternate message. 0
for no alternate message or 1 for alternate message.
Example: Caller dials into the system and is answered by the AA card. The caller then input
the special code or ‘password’ 48#2. The caller then dials 3 to select ring plan 3 and then
dials 1 to turn on the alternate greeting. The system now ring according to ring plan 3. Ring
plan 3 is directed to the AA card and the caller is now answered by the alternate greeting.
CONDITIONS
NONE
DEFAULT DATA
TABLE 01
Entry
Digits
Destination
001
0
500
002
2***
B
003
3***
B
004
5***
B
005
8***
B
006
9
P03
ALL OTHER TABLES ARE EMPTY
2-270
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
PROGRAM BUTTONS
A
B
C
D
Used to enter P on destination field
Used to enter B on digit or destination field
Used to enter C on destination field
Used to enter D on destination field
ACTION
DISPLAY
1. Press Transfer button and enter 732.
Display shows:
AA TRANS TB (01)
2. Dial TABLE number.(01-12, e.g., 02)
OR
Press Volume button to select and press Right
Soft button.
AA TRANS TB (02)
3. Dial ENTRY number.(001-100, e.g., 002)
OR
Press Volume button to select and press
Right Soft button.
AA TRANS TB (02)
4. Enter Dial DIGIT and press Right Soft button.
AA TRANS TB(02)
001:0 500
001: NONE
002: NONE
002:2
5. Enter Destination.
OR
Press Volume button to select and press
Right Soft button.
NONE
AA TRANS TB(02)
002:2
201
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 733
MMC 507
© SAMSUNG Electronics Co., Ltd.
AUTO ATTENDANT PLAN PROGRAMMING
RING PLAN TIME
2-271
CHAPTER 2. MMC Programming
[733] AA PLAN TABLE
Used to program each AA plan. A plan is a module that processes a call. There are twelve
plans available in each AA card. Each plan can route a caller to any group, extension or
another plan. Each port can answer calls with a different plan as defined in MMC 735.
This MMC includes options to select messages to play to a caller. These messages can be
as follows:
Message
MESSAGES 01-48
Description
These can be created using the AAREC Soft button(programmed on
phones by using MMC 722 or 723). A total of two minutes of message
time is available.
MESSAGES 49-64
These are pre-programmed as follows:
(The announcement may be different according to the AA MSG ROM)
49
‘Thank you for calling, please dial your party’s extension number’.
50
‘Invalid number, please try again’.
51
‘I’m sorry, there is no answer’.
52
‘I’m sorry, that station is busy’.
53
‘One moment please’.
54
‘Transferring’.
55
‘I’ll transfer you’.
56
‘Good-bye’.
57
‘Thank you’.
58
‘Please hold for the operator’.
59
‘Please hold for assistance’.
60
‘Thank you, good-bye’.
61
‘I’m sorry, all stations are presently busy’.
62
‘I’m sorry, all stations are still busy’.
63
‘Please call back later’.
64
‘I’m sorry, not a valid selection’.
PLAN MESSAGE
This is the message that will be heard by the caller when the AA port
(RING PLANS 01-06)
answers a call if the telephone system is in a particular ring mode or if
another message has been selected by the AA administrator. This
message has a default selection of AA ROM message number 49 but it
can be replaced with a customized message(01-48) or with any other
ROM message(49-64). For instructions on how to create these recordings
see Special Applications, Auto Attendant/Uniform Call Distribution.
ALTERNATE
This is the message that will be heard by the caller when the AA port
MESSAGE
answers a call if this message has been selected by the AA administrator.
This message has a default selection of 49 but it can be replaced with a
customized message(01-48) or with any other ROM message(49-64). For
instructions on how to create these recordings see Special Applications,
Auto Attendant/Uniform Call Distribution.
2-272
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Message
INVALID MESSAGE
Description
Determines what message will play if the caller dials invalid digits
repeatedly until the retry counter expires. Invalid digits are digits not
contained in the translation table for this plan. The invalid message will
repeat for the value contained in the retry counter. This message has a
default selection of ROM message 64 but it can be replaced with a
customized message(01-48) or with any other ROM message(49-64). For
instructions on how to create these recordings see Special Applications,
Auto Attendant/Uniform Call Distribution.
NO ANSWER
Determines what message will play if the caller is recalled to the AA port
MESSAGE
because of a no answer. This message has a default selection of ROM
message number 51 but it can be replaced with a customized
message(01-48) or with any other ROM message(49-64). For instructions
on how to create these recordings see Special Applications, Auto
Attendant/Uniform Call Distribution.
TRANSFER
Determines what message will play if the caller is transferred. This
MESSAGE
message has a default selection of ROM message number 53 but it can
be replaced with a customized message(01-48) or with any other ROM
message(49-64). For instructions on how to create these recordings see
Special Applications, Auto Attendant/Uniform Call Distribution.
BUSY MESSAGE
Determines what message will play if the caller selects a busy station.
This message has a default selection of ROM message number 52 but it
can be replaced with a customized message(01-48) or with any other
ROM message(49-64). For instructions on how to create these recordings
see Special Applications, Auto Attendant/Uniform Call Distribution.
NO STATION
Determines what message will play if the caller dials an invalid
MESSAGE
extension(not installed). This message has a default selection of ROM
message number 50 but it can be replaced with a customized
message(01-48) or with any other ROM message(49-64). This retry
message will repeat for the value contained in the retry counter. See Retry
Count. For instructions on how to create these recordings see Special
Applications, Auto Attendant/Uniform Call Distribution.
NO ACTION
Determines what message will play if the caller does not act. This
MESSAGE
message has a default selection of ROM message number 59 but it can
be replaced with a customized message(01-48) or with any other ROM
message(49-64).
CAMP-ON
Determines if calls will be transferred to busy stations. Calls transferred to
busy stations will be camped-on. The default value is OFF.
ANSWER DELAY
Sets how many rings will occur before this plan answers a call. The
default value is 01 second.
RETRY COUNT
Determines how many selection errors a caller may make before being
transferred to the invalid digits destination. In case of no action, will not
follow this option. .
© SAMSUNG Electronics Co., Ltd.
2-273
CHAPTER 2. MMC Programming
Message
Description
TRANSLATION
Determines what translation table this plan will use.(see MMC 732 Auto
TABLE
Attendant Trans Table). The default value is same number of plan number.
BUSY DESTINATION
Determines the destination for the call if the selected destination is busy.
This can be another station, station group or plan. Plans are entered by
pressing A button plus two digits 01-12.
NO ANSWER
Determines the destination for the call if the selected destination does not
DESTINATION
answer. This can be another station, station group or plan. Plans are
entered by pressing A button plus two digits 01-12.
NO ACTION
Determines the destination for the call if the caller makes no response(this
DESTINATION
is also the destination for rotary dial callers). This can be another station,
station group or plan. Plans are entered by pressing A button plus two
digits 01-12.
INVALID
Determines the destination for the call if the caller dials invalid digits after
DESTINATION
the retry counter has expired. This destination can be another station,
station group or plan. Plans are entered by pressing A button plus two
digits 01-12.
NOTE ABOUT
UCD is designed to hold a call until an agent is available. It is therefore
TRUNK SIGNALING
essential that a customer gets a disconnect from the Trunk Line when a
caller hangs up. If not the call may be held in the UCD loop until
answered. This could be a long time, and when an agent finally does
answer there would be no one there.
CONDITIONS
NONE
DEFAULT DATA
RETRY COUNT: 3
BUSY DESTINATION: 500
NO ANSWER DESTINATION: 500
NO ACTION DESTINATION: 500
INVALID DESTINATION: 500
PROGRAM BUTTONS
A
2-274
Used to enter P on destination field
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
ACTION
DISPLAY
1. Press Transfer button and enter 733.
Display shows:
AA PLAN PROG(01)
2. Enter AA plan number via dial keypad.
OR
Press Volume button to select a plan number and
press Right Soft button to move cursor.
AA PLAN PROG(05)
3. Enter option number via dial keypad.
OR
Press Volume button to select a option and press
Right Soft button to move cursor.
AA PLAN PROG(05)
4. Enter option data via dial keypad.
OR
Press Volume button to select a data and press
Right Soft button to save and return to step3.
AA PLAN PROG(05)
PLAN MSG1 :49
PLAN MSG1 :49
PLAN MSG3 :49
PLAN MSG3 :02
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 507
MMC 732
© SAMSUNG Electronics Co., Ltd.
RING PLAN TIME
AUTO ATTENDANT TRANS TABLE
2-275
CHAPTER 2. MMC Programming
[734] AUTO ATTENDANT MESSAGE MATCH
It is possible to make 48 customized recordings on the AA ports of the AA card.
For instructions on how to create these recordings, see User Instructions, Auto Attendant
and Uniform Call Distribution System Administration.
It is important to understand the difference between recordings and messages.
For example, you have customized recording 01 as ‘Thank you for calling’ and you have
customized recording #02 as ‘One moment please’. By default, message 01 is recording 01.
When message 01 is selected as part of AA or UCD programming, the caller hears ‘thank
you for calling’(recording 01). When message 02 is selected, the caller hears ‘one moment
please’(recording 02). If you need a new message that says ‘thank you for calling, one
moment please,’ you can record this as recording 03 and play it as message 03 but this uses
some of the RAM storage on the AA card.
An easier way is to link recordings 01 and 02 to produce message 03.
This is the purpose of this MMC. We simply tell the system that message 03 equals
recording 01 plus recording 02. In this MMC, the top line of the phone display indicates a
message number and the bottom line indicates the recording numbers.
CONDITIONS
Not applicable when playing using [AAPLAY] button.
DEFAULT DATA
EACH MESSAGE IS EQUAL TO THE CORRESPONDING RECORDING
ACTION
DISPLAY
1. Press Transfer button and enter 734.
Display shows:
AA MSG MATCH(01)
2. Enter message number via dial keypad.
OR
Press Volume button to select a message and
press Right Soft button to move cursor.
AA MSG MATCH(05)
3. Enter one or more recording numbers and press
Right Soft button to return step 2.
AA MSG MATCH(05)
01
05
26+14+45+12+02
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 607
MMC 733
MMC 739
2-276
UCD OPTIONS
AUTO ATTENDANT PLAN PROGRAMMING
SET AUTO ATTENDANT MUSIC ON HOLD
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[735] AA USE TABLE
Determines what plan will answer each call. Each AA is assigned a specific plan and each
AA group assigned in MMC 601 is assigned a specific plan. When a call is received by an
AA port, the appropriate plan will answer the call depending on the port or group that was
called.
Programming what port is called
You are not programming what port answers, but what port is called.
The following example shows how flexible this system is:
AA Port or Group
AA Plan to Answer
3951
PLAN 01
3952
PLAN 02
3953
PLAN 03
AA GROUP 510(3951, 3952, 3953)
PLAN 04
AA GROUP 511(3951, 3952)
PLAN 05
AA GROUP 512(3953, 3954)
PLAN 06
CONDITIONS
NONE
DEFAULT DATA
ALL PORTS AND GROUPS: PLAN 01
© SAMSUNG Electronics Co., Ltd.
2-277
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 735.
Display shows first AA group:(e.g., 510)
PLAN NO:01
2.
[510] AA PLAN
Enter AA port or AA group number.
OR
Press Volume button to select a AA port or group
and press Right Soft button to move cursor.
3. Enter AA plan number.
Press Volume button to select a AA plan number
and press Right Soft button to save and return step 2.
518] AA PLAN
PLAN NO:01
[510]AA PLAN
PLAN NO:04
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 601
MMC 733
2-278
ASSIGN STATION GROUP
AUTO ATTENDANT PLAN PROGRAMMING
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[736] ASSIGN AA MOH
Used to define what message 01-48 plays as a Music on Hold(MOH) source if selected in
MMC 309 or 408. This message will repeat continuously. Only the last AA port on an AA
card can be used as a MOH source. This MMC assigns a message number to the last port of
each card. This MMC must be programmed before AA/MOH data can be assigned in
MMCs 309, 408 and 607.
CONDITIONS
This MMC must be programmed before AA/MOH data can be assigned in MMCs 309, 408
and 607.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 736.
Display shows:
[3958]SET AAMOH
2. Enter AA port number.
OR
Press Volume button to select a AA port and
press Right Soft button to move cursor.
[3958]SET AAMOH
3. Enter AA MOH message number.
Press Volume button to select a AA MOH
number and press Right Soft button to save
and return step 2.
[3958]SET AAMOH
MOH MSG :NOT USE
MOH MSG :NOT USE
MOH MSG :33
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 309
MMC 408
MMC 607
MMC 734
© SAMSUNG Electronics Co., Ltd.
ASSIGN STATION MUSIC ON HOLD
ASSIGN TRUNK MOH SOURCE
UCD OPTIONS
AUTO ATTENDANT MESSAGE MATCH
2-279
CHAPTER 2. MMC Programming
[737] DECT SYSTEM CODE
Used to identify your DECT system and the handsets your register with your system.
The DECT system Code for your system is actually made up of two fields:
the System ID which is three hexadecimal digits in the range 000 to 999; and the Auth
Code(short for Authentication Code) which is four hexadecimal digits in the range 0000 to
9999. The default values are 000 and FFFF respectively.
The DECT System Code/Register handsets Change
Only the system administrator and/or installer should be allowed access to
change the DECT System Code and register handsets.
CONDITIONS
You must use this MMC to change the default values for the values you have been
provided with by your supplier. If you do not change the defaults you will not be able
to register handsets.
Once you have entered your new System ID and Auth Code using this MMC you can
then begin registering your handsets with the Auth Code. The system checks the Auth
Code entered for each handset against the DECT Auth Code. If it is the same, the
registration procedure continues; otherwise, the system rejects the registration
procedure.
DEFAULT DATA
AUTH CODE: FFFF
SYSTEM ID: 000
ACTION
DISPLAY
1. Press Transfer button and enter 737.
Display shows:
DECT SYSTEM CODE
2. Dial 0 for AUTH code or 1 for system ID.
OR
Press Volume button to make a selection and
press Right Soft button to move cursor.
DECT SYSTEM CODE
3. If option is AUTH code, enter AUTH CODE
via dial keypad.(e.g., 1234)
DECT SYSTEM CODE
If option is system ID, enter system ID via dial
keypad.(e.g., 567)
2-280
AUTH CODE:FFFF
AUTH CODE:FFFF
AUTH CODE:1234
DECT SYSTEM COD
SYSTEM ID:567
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 738
MMC 741
MMC 742
MMC 743
MMC 744
MMC 745
© SAMSUNG Electronics Co., Ltd.
DECT CLEAR REGISTRATION
DBS RESTART
BSI STATUS
DBS STATUS
DECT REGISTRATION ON/OFF
BSI RF CARRIER
2-281
CHAPTER 2. MMC Programming
[738] DECT CLEAR REGISTRATION
Used for deleting previously registered information of DECT handsets.
This MMC has two modes:
Mode
FORCED
Description
When this mode is programmed, the system clears the registered information by
force.
NORMAL
Whenever the system wants to clear the registration of a DECT handset, the deletion
must be confirmed from the handset. If the confirmation is successful, the system
clears the registered information.(If the confirmation fails, the system cannot clear
the information)
CONDITIONS
NONE
DEFAULT DATA
FORCED M’ODE
ACTION
2-282
DISPLAY
1. Press Transfer button and enter 738.
Display shows:
[8801]DECT CLEAR
2. Enter DECT terminal number via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button.
[8801]DECT CLEAR
3. Enter 0 for FORCED mode or 1 for NORMAL
Mode.
OR
Press Volume button to make selection and
press Right Soft button.
[8801]DECT CLEAR
4. Enter 1 for YES or 0 for NO.
OR
Press Volume button to make selection and press
Right Soft button.
[8801]DECT CLEAR
MODE:FORCED
MODE:FORCED
MODE:NORMAL
DECT CLEAR
:NO
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
5. Enter 1 for YES or 0 for NO.
OR
Press Volume button to make selection and
press Right Soft button.
[8801]DECT CLEAR
CLR RECORDED?NO
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 737
MMC 741
MMC 742
MMC 743
MMC 744
MMC 745
© SAMSUNG Electronics Co., Ltd.
DECT SYSTEM CODE
DBS RESTART
BSI STATUS
DBS STATUS
DECT REGISTRATION ON/OFF
BSI RF CARRIER
2-283
CHAPTER 2. MMC Programming
[740] STATION PAIR
Assigns a secondary station to a phone. This secondary station can be a phone or single line
port. The secondary station assumes the Call Forwarding, Class of Service, LCR Class, and
DND attributes of the primary station.
If the COS is changed for either station in MMC 301 the change affects both
stations. Secondary stations when dialled will also ring the primary extension.
Message from secondary extension will display that(secondary) extension
numbers. Callback to extension(secondary) as well.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 740.
Display shows.
[201] PRIMARY
2. Enter the primary station number via dial
keypad.(e.g., 201)
OR
Press Volume button to select and press Right
Soft button.
[201] PRIMARY
3. Enter the secondary station number via
dial keypad.(e.g., 205)
OR
Press Volume button to select and press Right
Soft button.
[201] PRIMARY
SECONDARY:NONE
SECONDARY:NONE
SECONDARY:205
4. Press Transfer button and enter button to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 102
MMC 301
MMC 310
2-284
STATION FORWARDING
STATION COS
LCR CLASS OF SERVICE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[741] DBS RESTART
Provides a method of restarting DBS and BSI card.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 741.
Display shows:
BSI SLOT:1 DBS:1
2. Select the BSI slot via dial button pad.
OR
Press Volume button to select BSI slot and press
Right Soft button.
BSI SLOT:1 DBS:1
3. Select the DBS number via dial button pad.
OR
Press Volume button to select DBS number and
Right Soft button.
BSI SLOT:1 DBS:3
If you want to restart BSI card, press ANS/RLS
button and press Right Soft button.
BSI SLOT:1 DBS:A
RESTART?
RESTART?
RESTART?
RESTART?
NO
NO
NO
NO
4. Enter 1 for YES or 0 for NO.
OR
Press Volume button to make selection and press
Right Soft button.
BSI SLOT:1 DBS:3
5. Enter 1 for YES or 0 for NO.
OR
Press Volume button to make selection and press
Right Soft button.
BSI SLOT:1 DBS:3
RESTART?
YES
ARE YOU SURE?NO
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
© SAMSUNG Electronics Co., Ltd.
2-285
CHAPTER 2. MMC Programming
RELATED ITEMS
MMC 737
MMC 738
MMC 742
MMC 743
MMC 744
MMC 745
2-286
DECT SYSTEM CODE
DECT CLEAR REGISTRATION
BSI STATUS
DBS STATUS
DECT REGISTRATION ON/OFF
BSI RF CARRIER
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[742] BSI STATUS
This MMC shows the status of the BSI card.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 742.
Display shows:
If status of BSI card is good, the display
shows ‘SUCC’.
BSI STATUS
M:SUCC-SUCC-SUCC
2. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 737
MMC 738
MMC 741
MMC 743
MMC 744
MMC 745
© SAMSUNG Electronics Co., Ltd.
DECT SYSTEM CODE
DECT CLEAR REGISTRATION
DBS RESTART
DBS STATUS
DECT REGISTRATION ON/OFF
BSI RF CARRIER
2-287
CHAPTER 2. MMC Programming
[743] DBS STATUS
This MMC shows the status of the DECT base stations(DBS).
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 743.
Display shows:
DBS 12345678 S:1
2. Select the BSI card via dial button pad.
OR
Press Volume button to make selection.
The status of each DBS is displayed.
If the status is good, ‘1 is displayed.
If the status is not good, ‘0 is displayed.
DBS 12345678 S:2
STS:00000000
STS:00000000
3. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 737
MMC 738
MMC 741
MMC 742
MMC 744
MMC 745
2-288
DECT SYSTEM CODE
DECT CLEAR REGISTRATION
DBS RESTART
BSI STATUS
DECT REGISTRATION ON/OFF
BSI RF CARRIER
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[744] DECT REGISTRATION ON/OFF
Allows DECT handset registration to be enabled on a system. If this MMC is not opened
and an attempt is made to register a DECT handset, an error message will be displayed.
The default passcode can be changed using MMC 202.
CONDITIONS
NONE
DEFAULT DATA
DISABLE
ACTION
DISPLAY
1. Press Transfer button and enter 744.
Display shows:
ENABLE DECT REG.
2. Enter passcode.
ENABLE DECT REG.
PASSCODE:_
PASSCODE:****
If the correct code is entered the display shows.
ENABLE DECT REG.
If the SYSTEM ID in MMC 737 has not been
set, the following message will be displayed.
ENABLE DECT REG.
3. Dial 1 for ENABLE or 0 for DISABLE.
OR
Press Volume button to select and press
Right Soft button.
DISABLE
NO REG.SYSTEM ID
ENABLE DECT REG.
ENABLE
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 737
MMC 738
MMC 741
MMC 742
MMC 743
MMC 745
© SAMSUNG Electronics Co., Ltd.
DECT SYSTEM CODE
DECT CLEAR REGISTRATION
DBS RESTART
BSI STATUS
DBS STATUS
BSI RF CARRIER
2-289
CHAPTER 2. MMC Programming
[745] BSI RF CARRIER
A base station uses one of 10 channels(FDMA technology). This MMC is used to allow or
deny the use of each channel(carrier). By default, all carriers can be used by a base station.
0.
1.
Carrier can be used
Carrier cannot be used
CONDITIONS
NONE
DEFAULT DATA
1111111111
ACTION
DISPLAY
1. Press Transfer button and enter 745.
The display shows the status of each carrier
(0-9): If ‘1 is shown below a carrier then this
carrier can be used by the base station.
CARS:0123456789
SELS:1111111111
If ‘0 is shown below a carrier then this carrier
cannot be used by the base station.
2. Dial 1 or 0 for each carrier.
3. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 737
MMC 738
MMC 741
MMC 742
MMC 743
MMC 744
2-290
DECT SYSTEM CODE
DECT CLEAR REGISTRATION
DBS RESTART
BSI STATUS
DBS STATUS
DECT REGISTRATION ON/OFF
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[746] COSTING DIAL PLAN
The COSTING DIAL PLAN is used to analyze the leading dialled digits of a dialled
number and determine what DIAL PLAN it is to follow. Data entry for this program is in
three fields: ENTRY, DIGITS and COST RATE table reference.
DIGITS
Up to 500 entries may be made. Each entry can be up to ten digits. These are the entries
that will be searched to find a match with the digits dialled by the station making the call.
This is a leading digits table and the system will look for the exact leading digits in the
table that match the number dialled. For example, if a user dials 1305 and the COSTING
DIAL PLAN contains 1, 1308 and 1312, the dialled digits will be matched to 1 because
1308 and 1312 do not form a complete match. When this table is created by the technician
or when any new entries are added, the system automatically places all entries in numerical
order.
Wild cards( ) can be used to represent any digit. The Toll Restriction Wild Character
assignment(MMC 704) is common with Call Costing and Toll Restriction. When all entries
are used, [LAST ENTRY] is displayed.
DIAL PLAN
This shows in the programming display as DP and represents a pattern(1-7, 8).
This pattern is used by MMC 433 TRUNK COST RATE, to determine the correct billing
according to MMC 747 RATE CALCULATION TABLE
When the system finds a DIAL PLAN match for the digits dialled, the system checks
MMC 747 to see what RATE CALCULATION to use for costing the call.
EXAMPLES
When a station user dials a number, the system will search the COSTING DIAL PLAN to
find a match. If 13056 is dialled and this MMC contains entries 1, 13, 1305 and 1401, 1305
is the closest match and this entry will be selected. If 1305 is dialled and this MMC
contains entries 1, 13, 13056 and 1401, no action will be taken until the station user dials
another digit. If the next digit is 6, the 13056 entry is the closest match and this entry will
be selected, but if the next digit is anything other than 6,
the 13 entry is the closest match.
Whenever a new entry is added, the system will sort all entries in numerical order because
this is the logical order in which the system analyzes digits. Wild cards are checked after
exact digits. If 1813 and 18 are entered, the system will check 1813 first. If no match is
found, it will check 18 .
© SAMSUNG Electronics Co., Ltd.
2-291
CHAPTER 2. MMC Programming
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 746.
Display shows:
COST DP
(001)
2. Dial CALL COST entry.(e.g., 005)
OR
Press Volume button to select entry and
press Right Soft button to move cursor.
COST DP
(005)
3. Enter digit string via the dial keypad and
press Right Soft button.
COST DP
(005)
4. Enter DIAL PLAN.(1-8)
OR
Press Volume button to select dial plan and
press Right Soft button to save and move step 2.
COST DP
(005)
DIGIT:
DIGIT:
DIGIT:1305
CALL RATE: NONE
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 433
MMC 747
2-292
COST RATE
RATE CALCULATION TABLE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[747] RATE CALCULATION TABLE
The RATE CALCULATION TABLE is used to define the billing charges for each COST
RATE. These rate tables correlate with the Trunk Cost Rate and the Costing Dial Plan.
There are eight call costing rates. Each rate has the following data fields.
No
0
Type
Description
FIRST INTERVAL
This is the amount of time at the beginning of each call to which a
DURATION
fixed cost is applied. The range is from 0 to 999 seconds, for
example, 180 seconds(three minutes).
1
2
FIRST INTERVAL
This is the dollar cost for the first interval duration.
COST
The range is from 0 to 999, for example, 345($3.45).
SECOND INTERVAL
This is the amount of time for the duration of each billing increment
DURATION
after the first interval has expired. The range is from 0 to 999
seconds, for example, 006 seconds(six seconds).
3
4
SECOND INTERVAL
This is the dollar cost for each billing increment. The range is from
COST
0 to 999, for example 100($1.00).
SURCHARGE
This is a one-time charge that is applied to the call over and above
the time charges. The range is from 0 to 999, for example
150($1.50).
CONDITIONS
NONE
DEFAULT DATA
ALL COST RATES NO DATA
ACTION
DISPLAY
1. Press Transfer button and enter 747.
Display shows:
COST RATE (1)
2. Dial COST RATE number.(1-8, e.g., 3)
OR
Press Volume button to select COST RATE and
press Right Soft button to move cursor.
COST RATE (3)
3. Dial option number.(0-4, e.g., 1)
OR
Press Volume button to select option and press
Right Soft button to move cursor.
COST RATE (3)
© SAMSUNG Electronics Co., Ltd.
1ST DUR :000 SEC
1ST DUR :000 SEC
1ST COST:000
2-293
CHAPTER 2. MMC Programming
4. Enter data via dial keypad.(e.g., 125: $1.25)
OR
Press Volume button to select data and press
Right Soft button to save and move step 3.
COST RATE (3)
1ST COST:125
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 433
MMC 746
2-294
TRUNK COST RATE
COSTING DIAL PLAN
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[750] VM CARD RESTART
This MMC is only used for the Samsung Plug In Voice Mail Card.
There are two options available in this MMC:
No
0
Option
DOWNLOAD
Description
When the Built-In Voice Mail card starts, part of the power up
procedure will download data from the system to determine time,
date, what mailboxes to create, and system numbering plan. This
must be done at least once, but once done this download feature
can be turned NO to save boot up time.
1
CARD RESTART
If this option is set to YES the Built-In Voice Mail card will
immediately restart according to the download OPTION specified
above.
2
VIRTUAL NUMBER
This option is determine which type virtual port include during
DOWNLOAD
mailbox and system numbering plan downloading procedure.
The virtual port type are followed:
No
Type
Description
0
VIRTUAL EXT
Virtual extension number
1
DESKTOP ITP
DESKTOP IP-based phone number
2
DECT PHONE
DECT terminal number
3
MOBILE ITP
Wireless IP-based mobile phone
number
4
BRI STATION
ISDN terminal number
5
VOIP NET TRK
VoIP networking trunk number
6
VOIP 323 TRK
VoIP H.323 trunk number
7
VOIP SIP TRK
VoIP SIP trunk number
8
REMOTE STN
Remote station number via networking
Remove Built-In Voice Mail Card
If during any test procedures you need to run the system with a default database
and power up with this MMC option set to YES the Built-In Voice Mail database
will be overwritten according to the data in MMC 751 and the default numbering
plan. If you plan this type of test, remove Built-In Voice Mail Card until the
procedure is finished and the customer database is reloaded.
© SAMSUNG Electronics Co., Ltd.
2-295
CHAPTER 2. MMC Programming
CONDITIONS
NONE
DEFAULT DATA
ALL OPTIONS ARE NO
ACTION
DISPLAY
1. Press Transfer button and enter 750.
Display shows:
VM CARD RESTART
2. Dial 0,1 or 2 to set option and advance.
OR
Press Volume button to make selection and press
Right Soft button.
VM CARD RESTART
3. Dial 0(No) or 1(Yes) to confirm selection.
OR
Press Volume button to make selection and press
Right Soft button.
VM CARD RESTART
DOWNLOAD
? NO
CARD RESTART?NO
ARE YOU SURE?NO
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-296
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[751] ASSIGN MAILBOX
This MMC is only used for the Samsung Plug in Voice Mail Card. It assigns each station or
group as having a mailbox(yes or no). When stations or groups are flagged as YES, during
Voice Mail card power up mailboxes will be created for each directory number with a
‘YES’ entry.
Once the Voice Mail database has been created new boxes can be added.
a) Through Voice Mail administration,
b) By adding a new mailbox in this system and cycling system power.
If a mailbox is to be removed it must be done through Voice Mail administration.
If a station that do not have an associated voice mailbox, call the Voice Mail system they
will be answered by the Voice Mail system main greeting.
CONDITIONS
Mailboxes that are needed for people that do not have an extension must be added through
Voice Mail programming.
DEFAULT DATA
ALL STATIONS: YES
ALL GROUPS: NO
ACTION
DISPLAY
1. Press Transfer button and enter 751.
Display shows:
ASSIGN MAIL BOX
2. Dial station number.
OR
Press Volume button to scroll the number and
press Right Soft button to move cursor.
ASSIGN MAIL BOX
3. Dial 0 for NO or 1 for YES.
OR
Press Volume button to make selection and press
Right Soft button to save and move stop 2.
ASSIGN MAIL BOX
[201]
[202]
[202]
YES
YES
NO
4. Press Transfer button and enter button to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-297
CHAPTER 2. MMC Programming
[752] AUTO RECORD
This MMC is only used for the Samsung Plug in Voice Mail Card.
Some specific station in the phone system can be assigned to automatically record
conversations. When this option is set, all incoming, all outgoing, or all calls(incoming or
outgoing) can be recorded.
When this option is selected a specific port can be assigned for each station set to automatic
conversation recording or the effectiveness of this feature cannot be guaranteed.
In this MMC you can assign:
1.
2.
3.
4.
Which station use this feature.
-Station number.
What mailbox the conversation are recorded in.
-Mailbox number.
What type of conversations are recorded, in, out or both.
-I, O or B.
What port is dedicated to the station.
-Voice mail port number.
A maximum of 8 stations can this feature in the system.
The same port cannot be assigned to more than one station. Attempts to do this will result
in an error message.
When a Voice Mail port is assigned here, it is automatically removed from the Voice Mail
group defined in MMC 601.
When using this feature
Before using this feature make sure that you are not violating any state or federal
laws. Some states require that the recorded party be notified. SAMSUNG is not
responsible for any illegal use of this feature.
CONDITIONS
When a Voice Mail port is assigned here, it is automatically removed from the Voice Mail
group defined in MMC 601.
DEFAULT DATA
NONE
2-298
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
ACTION
DISPLAY
1. Press Transfer button and enter 752.
Display shows:
AUTO RECORD
2. Dial station number via dial keypad.
OR
Press Volume button to make selection and press
Right Soft button to move cursor.
AUTO RECORD
3. Dial mailbox number via dial keypad.
OR
Press Volume button to make selection and press
Right Soft button to move cursor.
AUTO RECORD
4. Dial VM number via dial keypad.
OR
Press Volume button to make selection and press
Right Soft button to move cursor.
AUTO RECORD
5. Dial call type via dial keypad. (0: I, 1: O or 2: B)
OR
Press Volume button to make selection and press
Right Soft button to move cursor.
AUTO RECORD
STN:201
STN:201
STN:201
PORT:209
PORT:209
MB:NONE
MB:NONE
MB:201
CALL:I
CALL:B
6. Press Transfer button and enter button to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-299
CHAPTER 2. MMC Programming
[753] WARNING DESTINATION
This MMC is only used for the Samsung Plug in Voice Mail Card.
This MMC provides an emergency destination for calls destined for the Voice Mail card, if
the Voice Mail card is removed or is offline.
In addition any calls that are forwarded to the Voice Mail card will not forward, they will
remain ringing at the ‘fwd from’ station until answered.
This destination can be a station number or a group number.
CONDITIONS
NONE
DEFAULT DATA
500
ACTION
DISPLAY
1. Press Transfer button and enter 753.
Display shows:
WARNING DEST.
2. Dial station number or group number.
OR
Press Volume button to scroll the number.
WARNING DEST.
DEST:500
DEST:501
3. Press Transfer button and enter button to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-300
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[754] VM HALT
This MMC is only used for the Samsung Plug in Voice Mail Card.
This MMC is used to halt the Voice Mail card(take it offline). It ensures that there is no
traffic on the Voice Mail card when it is removed from the system.
CONDITIONS
This operation should be performed before removing the voice mail card mail card from
the system.
DEFAULT DATA
PROC
ACTION
DISPLAY
1. Press Transfer button and enter 754.
Display shows:
VM HALT
2. Enter 1 to halt or 0 to process.
OR
Press Volume button to scroll the selections.
VM HALT
3. When you select 1 to halt, display shows:
Press 1 to confirm.
VM HALT
4. Display shows:
VM HALT
STATUS:PROC
STATUS:PROC
ARE YOU SURE?YES
STATUS:HALT
5. Press Transfer button and enter button to exit.
OR
Press Speaker button to advance next MMC.
DEFAULT DATA
PROC
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-301
CHAPTER 2. MMC Programming
[755] VM ALARM
This MMC is only used for the Samsung Plug in Voice Mail Card.
This MMC will generate an alarm message in the mailbox defined in MMC 751 whenever
the Voice Mail disk drive reaches a threshold.
The threshold is measured in % full. This means that if the MMC is set for 80, the alarm
will be generated when the disk exceeds 80 % of the available drive space.
CONDITIONS
NONE
DEFAULT DATA
80 %
ACTION
DISPLAY
1. Press Transfer button and enter 755.
Display shows:
VM ALARM
2. Enter new threshold level.
VM ALARM
THRESHOLD:80
THRESHOLD:75
3. Press Transfer button and enter button to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-302
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[756] ASSIGN VM MOH
This MMC is only used for the Samsung Plug in Voice Mail Card.
This MMC is used to assign each port a Music on Hold source for the system from a sound
file located on the Built-In Voice Mail Card hard disk drive. The 100 available sound files
are defined as numbers 5000 to 5099.
Basically Built-In Voice Mail Card supports various music for numbers 5000 to 5099. If
you want to use default Built-In Voice Mail Card support music, select the number.
Otherwise, make sure you record the sound file first. The next step is to assign the sound
file to a Built-In Voice Mail port. For example, if you record sound file 5025 you would
associate 25 with a specific Built-In Voice Mail port, e.g., 225. This will dedicate the port
for use only as MOH and remove it from group 529 or 549.
Now 225 will show up as a valid music source in MMC 308, 309 and 408.
Each Music on Hold source assigned here requires one Built-In Voice Mail port.
When the first Built-In Voice Mail port is used for VMMOH
If the first Built-In Voice Mail port is used for VMMOH, it must be disabled before
boot up since Built-In Voice Mail Card and the system use port 1 during boot up to
exchange critical information. For this reason we suggest you use the last port as
VMMOH ports.
CONDITIONS
NONE
DEFAULT DATA
NOT USE
ACTION
DISPLAY
1. Press Transfer button and enter 756.
Display shows:
SET VMMOH
2. Dial VM number.
OR
Press Volume button to make a selection and
press Right Soft button to move cursor.
SET VMMOH
© SAMSUNG Electronics Co., Ltd.
209 : NOT USE
215 : NOT USE
2-303
CHAPTER 2. MMC Programming
3. Enter VM message number.
OR
Press Volume button to make a selection and
press Right Soft button to move cursor.
SET VMMOH
215 : 25
4. Press Transfer button and enter button to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-304
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[757] VM IN/OUT
This MMC is only used for the Samsung Plug in Voice Mail Card.
This MMC is used to assign each Voice Mail Port as used for incoming, outgoing or both
way calls. Note that this MMC must support outgoing calls if off premises
notification(beeper, outbound follow me of outbound notification) is used.
CONDITIONS
NONE
DEFAULT DATA
IN/OUT
ACTION
DISPLAY
1. Press Transfer button and enter 757.
Display shows:
VM IN/OUT
2. Dial VM number.
OR
Press Volume button to make a selection and
press Right Soft button to move cursor.
VM IN/OUT
3. Enter In or Out via dial keypad.
OR
Press Volume button to make a selection and
press Right Soft button to move cursor.
VM IN/OUT
209 : IN/OUT
215 : IN/OUT
215 : IN
4. Press Transfer button and enter button to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-305
CHAPTER 2. MMC Programming
[758] VM DAY/NIGHT
This MMC is only used for the Samsung Built-In Voice Mail Card.
Built-In Voice Mail Card can operate in either a DAY or NIGHT operating mode.
This mode will determine what main menu greetings and options are played to the callers.
This operating mode can change automatically(if enabled in Built-In Voice Mail Card)
according to the setting in this MMC.
This MMC contains either a DAY or NIGHT instruction for each Ring Plan.
CONDITIONS
NONE
DEFAULT DATA
ALL RING PLANS: DAY
ACTION
DISPLAY
1. Press Transfer button and enter 758.
Display shows:
VM DAY/NIGHT
2. Enter ring plan number.
OR
Press Volume button to make a selection and
press Right Soft button to move cursor.
VM DAY/NIGHT
3. Dial 0 for day or 1 for night.
OR
Press Volume button to make a selection and
press Right Soft button to save and move cursor.
VM DAY/NIGHT
RING 1 : DAY
RING 3 : DAY
RING 3 : DAY
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 507
2-306
RING PLAN TIME
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[759] CLI RINGING
Assigns a specific CID number received from the central office to a specific ring plan
destination. And this programming allows the technician to reject the specific CID number
and assign its own priority. There are 9 priority levels: priority 1 is the highest and priority
9 is the lowest.
It also allows to select the ring tone heard at a phone when called by a specific CID number.
There is also a cadence control option to perform a similar function for single line sets.
There are eight ring tones available along with a Follow Station(NO) option for the phones.
There are 5 cadences and a Follow Station option(NO) for SLT’s
The CID Ringing table consists of 500 entries.
Option
Description
CLI
CID number to be received from the central office. Up to 16 digits may be
entered.
REJ
CID call reject option. When this sets YES, if a call comes that matched CID
number and CLI field then the system will be reject call.
PRI
CID priority option. There are 9 priority levels: priority 1 is the highest and
priority 9 is the lowest. When calls into station group come and group
members are all busy, the system will assign a priority to the CID number so
that calls from a high priority CID number will be placed at the front of the
group queue.
If this option sets NO, the longest call that placed at the group queue has
the highest priority.
R1: XXX, R2: XXX,
R3: XXX, R4: XXX,
R5: XXX, R6: XXX
Ring plan and destination during each ring plan. The destination can be a
station, station group.
TONE
Ring Tone options for a specific CID Number.(NO, 1~8)
No
1~8
CAD
Calls from the programmed CID number will ring phones with this
ring frequency.
Ring Cadence options for a specific CID Number at SLT’s(NO, 1~5)
No
© SAMSUNG Electronics Co., Ltd.
Calls will ring with the phone users choice of ring frequency.
Calls will ring with the normal SLT ring cadences.
1
Calls from the programmed CID number will ring SLT’s with the intercom
ring cadence.
2
Calls from the programmed CID number will ring SLT’s with the CO ring
cadence.
3
Calls from the programmed CID number will ring SLT’s with the DOOR
ring cadence.
4
Calls from the programmed CID number will ring SLT’s with the ALARM
ring cadence.
5
Calls from the programmed CID number will ring SLT’s with the
CALLBACK ring cadence.
2-307
CHAPTER 2. MMC Programming
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
1. Press Transfer button and enter 759.
Display shows first entry:
CLI RINGING(001)
2. Dial entry number.(e.g., 005)
OR
Use Volume button to scroll through entries
and press Right Soft button to select entry.
CLI RINGING(005)
3. Enter CID number and press Right Soft button
to advance next entry.
OR
Enter CID number and press Left Soft button
to return to step 2.
CLI RINGING(005)
4. Enter reject option via dial keypad.
(1 for YES, 0 for NO)
OR
Press Volume button to make selection and press
Right Soft button to advance next step.
CLI RINGING(005)
5. Enter priority level via dial keypad. ( 1-9 or NO)
OR
Press Volume button to make selection and press
Right Soft buttons to advance next step.
6. Enter station or group number for each Ring plan
destination via dial keypad.(e.g., 501)
OR
Press Volume button to make selection and press
Right Soft button to advance next step.
7. Dial 1-8(or NO)to select ring tone.(e.g., 2)
OR
Press Volume button to select ring tone and press
Right Soft button to move cursor.
2-308
DISPLAY
CLI:
CLI:_
CLI:1234567
REJ:ÒO
PRI:NO
ÝÔ× Î×ÒÙ×ÒÙøððë÷
ÎÛÖæÒÑ
ÐÎ×æÒÑ
ÝÔ× Î×ÒÙ×ÒÙøððë÷
Îïæëðï
ÎîæÒÑÒÛ
ÝÔ× Î×ÒÙ×ÒÙøððë÷
ÌÑÒÛæî
ÝßÜæÒÑ
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
8. Dial 1-5(or NO)to select ring cadence.
OR
Press Volume button to select ring cadence and
press Right Soft button to move cursor.
ÝÔ× Î×ÒÙ×ÒÙøððë÷
ÌÑÒÛæî
ÝßÜæÒÑ
9. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 312
© SAMSUNG Electronics Co., Ltd.
ALLOW CID
2-309
CHAPTER 2. MMC Programming
[760] ITEM COST TABLE
This MMC provides a means to assign a code to a billable item along with a 10 character
name for the item. There are a maximum of 100 entries(00 to 99) in the table with item 00
reserved as the code for room deposits, 01 reserved as the code for phone deposits and
items 89 to 99 are reserved for other PMS stream items.
These item codes with the exception of codes 93 to 99 will appear on the guests bill at
checkout and will serve to identify what each charge on the bill is for. The room bill, when
printed will also show telephone calls with an item designation of TEL and the name field
will show the number dialled. In addition to the name up to 8 of the tax codes or rates
defined in MMC 761 can be applied to each item.
PRE DEFINED CODES
No
Code
Description
00
Room Deposit
This is the code used for pre pay room deposits.
01
Phone Deposit
This is the code used for pre pay phone deposits
02-88
-
User Assignable Code
89
W/UP SET
A wake up call was set
90
W/UP ANS
A wake up call was answered
91
W/UP N/ANS
A wake up call was not answered
92
W/UP CANCL
A wake up call was cancelled
93
Check In
A guest has checked into a room
94
Check out
A guest has checked out of a room
95
Available
A room has been flagged as AVAILABLE
96
Occupied
A room has been flagged as OCCUPIED
97
Clean Room
A room has been flagged as NEEDS CLEANING
98
Fix Room
A room has been flagged as NEED MAINTENANCE
99
Hold
A room has been flagged as HOLD
CONDITIONS
This function can be used only when the hotel function is enabled at ‘MMC 813 HOTEL
’.
INPUT CHARACTERS
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
2-310
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
DEFAULT DATA
NO ENTRIES
ACTION
DISPLAY
1. Press Transfer button and enter 760.
Display shows:
ITEM CODE
(00)
2. Enter valid code number(e.g., 02) via dial
keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
ITEM CODE
(02)
3. Enter in item name(e.g., ROOM COST) via key
pad using the method described above.
ITEM CODE
(02)
4. Press Right Soft button to move cursor to tax
entry step.
ITEM CODE
(02)
5. Enter in the tax rates in MMC 761 that apply to
this item and press Right Soft button to return to
step 2.
ITEM CODE
(02)
NAME:RM Deposit
NAME:
NAME:CLASS A
TAXES:00000000
TAXES:11000000
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 221
MMC 761
© SAMSUNG Electronics Co., Ltd.
EXTENSION TYPE
TAX RATE SETUP
2-311
CHAPTER 2. MMC Programming
[761] TAX RATE SETUP
This MMC allows the technician to set up the 8 tax rates used in MMC 760. Each tax rate
may be defined as a fixed value or as a percentage of the item cost. In addition a 10
character name may be used to define the reason for the tax. The Various options are
further detailed below.
Option
TAX RATE
Description
This is the number assigned to this tax rate. The tax rates are numbered 1 to 8 to
match the rate field in MMC 760 counting from left to right.
TYPE
This is the type of tax and defines if the VALUE is applied as a percentage(%) of
the cost of an item or is added as a fixed dollar value($) to an item or is applied as
a Inclusive VAT percentage(I) of the cost of an item.
VALUE
This is the actual tax rate that will be applied to the item cost.
NAME
This is a 10 character name that will be displayed on the room bill alongside the tax.
CONDITIONS
This function can be used only when the hotel function is enabled at ‘MMC 813 HOTEL
OPERATION’.
INPUT CHARACTERS
Refer to ‘INPUT CHARACTERS’ in ‘MMC [104] STATION NAME’.
DEFAULT DATA
All rates are %
ACTION
2-312
DISPLAY
1. Press Transfer button and enter 761.
Display shows:
TAX RATE
(1)
2. Enter valid tax number, e.g., 2 via dial button pad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
TAX RATE
(2)
3. Dial 0 for ‘%’, 1 for ‘C’ or 2 for ‘I’.
(Inclusive VAT)
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
TAX RATE
(2)
TYPE:% VAL:00.00
TYPE:% VAL:00.00
TYPE:C VAL:00.00
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
4. Enter in the tax rate or value via dial button pad.
OR
Press Volume button to make selection.
If valid entry, system advances cursor.
TAX RATE
(2)
5. Enter name using above table and press
Right Soft button to return to step 2.
TAX RATE
(2)
TYPE:C VAL:01.25
NAME:MIA BED
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 760
© SAMSUNG Electronics Co., Ltd.
ITEM COST TABLE
2-313
CHAPTER 2. MMC Programming
[762] ROOM COST RATE
This MMC allows the technician to set up the cost rates according to week. Each room cost
Rate can be assigned with the percentage of the room cost from Sunday to Saturday.
EXAMPLE: If you set SUN: 150 %, 1. MON: 100 %, 2.TUE: 090 % ...
If you set $100 for the room cost in CHECK-IN procedure under above condition.
The real room cost will be $150 on Sunday and $90 on Tuesday.
CONDITIONS
This function can be used only when the hotel function is enabled at ‘MMC 813 HOTEL
’.
DEFAULT DATA
All rates are 100 %
ACTION
DISPLAY
1. Press Transfer button and enter 762.
Display shows:
RM COST RAT(SUN)
2. Dial day number.(0-6, e.g., 2)
OR
Press Volume button to select day and press
Right Soft button to move cursor.
RM COST RAT(TUE)
3. Enter room cost rate.(001-999, e.g., 090)
RM COST RAT(TUE)
100% :
100% :
100% :090
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
DEFAULT DATA
All rates are 100 %
RELATED ITEMS
MMC 760
2-314
ITEM COST TABLE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[800] ENABLE TECHNICIAN PROGRAM
Used to open and close technician-level programming. If programming is not opened and
an attempt is made to access a system MMC, the error message will be displayed.
A four digit passcode is required to access this MMC. Each character can be digits
0-9. When opened, this MMC enables access to all MMCs.
CONDITIONS
A four digit passcode is required to access this MMC. Each character can be digits
0-9. When opened, this MMC enables access to all MMCs.
DEFAULT DATA
DISABLE
ACTION
DISPLAY
1. Press Transfer button and enter 800.
Display shows:
ENABLE TECH.PROG
2. Enter passcode.
ENABLE TECH.PROG
PASSCODE:
PASSCODE:
Correct code shows:
ENABLE TECH.PROG
DISABLE TENANT:1
Incorrect code shows:
ENABLE TECH. PROG
PASSCODE ERROR
3. Enter 1 to enable or 0 to disable.
OR
Press Volume button to select and press Right
Soft button to move tenant number and enter
tenant number(1-2).
ENABLE TECH.PROG
4. Press Speaker button to advance MMC entry level.
801:TEC.PASSCODE
ENABLE TENANT:1
SELECT PROG.ID
5. Enter the MMC desired.(e.g., 209)
209:AOM MASTER
AOM NOT EXIST
© SAMSUNG Electronics Co., Ltd.
2-315
CHAPTER 2. MMC Programming
6. To log out and return to MMC 800, press Volume
button to select DISABLE.
OR
Press Speaker button then Transfer to return to normal
display Programming option will time out
RELATED ITEMS
MMC 801
2-316
CHANGE TECHNICIAN PASSCODE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[801] CHANGE TECHNICIAN PASSCODE
Used to change the passcode which allows access to MMC 800 Enable Technician Program
from its current value.
CONDITIONS
The passcode is four characters long. Each character can be digits 0-9. The current or old
passcode is required for this MMC.
DEFAULT DATA
DEFAULT PASSCODE: 4321
ACTION
DISPLAY
1. Press Transfer button and enter 801.
TECH. PASSCODE
NEW CODE:_
2. Enter new passcode.
TECH. PASSCODE
NEW CODE:
3. Enter new passcode again.
TECH. PASSCODE
VERIFY
4. If passcode is correct, press Right Soft
key to continue and enter desired MMC.
If passcode is incorrect.
TECH. PASSCODE
VERIFY
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
:SUCCESS
TECH. PASSCODE
VERIFY
System returns to step 2.
:
:FAILURE
TECH. PASSCODE
NEW CODE:
RELATED ITEMS
MMC 8`00
© SAMSUNG Electronics Co., Ltd.
ENABLE TECHNICIAN PROGRAM
2-317
CHAPTER 2. MMC Programming
[802] CUSTOMER ACCESS MMC NUMBER
Allows the System Administrator to have access to certain MMCs. For example,
it is required that the System Administrator customer have access to MMC 102 Call
Forward for call forwarding but it is not required that the System Administrator have access
to MMC 710 LCR Digit Table for LCR dial plans. This MMC is for both tenants.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 802.
Display shows:
CUST.USE MMC :1
2. Enter desired tenant number(1-2) via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
MMC TENANT:1
3. Enter desired MMC number via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
MMC TENANT:1
4. Enter 1 for YES or 0 for NO via dial keypad.
OR
Press Volume button to make selection and
press Left Soft button to return to step 3
to make additional entries.
MMC TENANT:1
100:STN LOCK:YES
100:STN LOCK:YES
102:CALL FWD:YES
102:CALL FWD:NO
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-318
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[803] ASSIGN TENANT GROUP
Allows the assignment of tenant groups on a per-cabinet, slot and port basis.
The simple rule is Cabinet-Slot-Port = Tenant. The simplicity of this program allows for
flexible assignments. The only information needed is the correct correlation of entries.
CONDITIONS
NONE
DEFAULT DATA
ALL ASSIGNMENTS TENANT 1
ACTION
DISPLAY
1. Press Transfer button and enter 803.
Display shows:
TENANT GROUP
2. Enter cabinet number if no change press
Right Soft button to move cursor.
TENANT GROUP
3. Enter slot number if no change press Right
Soft button to move cursor.
TENANT GROUP
4. Enter port number if no change press
Right Soft button to move cursor.
TENANT GROUP
5. Enter tenant number if no change press
Right Soft button to return to step 2.
TENANT GROUP
C:1 S:1 -01
C:1 S:1 –01
C:1 S:2 -01
C:1 S:2 -03
C:1 S:2 -03
T:1
T:1
T:1
T:1
T:2
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
TENANT GROUP
© SAMSUNG Electronics Co., Ltd.
2-319
CHAPTER 2. MMC Programming
[804] SYSTEM I/O PARAMETER
Provides a means of assigning a system I/O port for use with one of the service types
detailed below. A system has two SIO ports defined as IOM ports 2 and 3 and an optional
modem port defined as port 5. In order for remote programming to work correctly the
modem port must be assigned as PCMMC.
No
0
Option
Description
SERVICE
No
Type
(Service Type)
Description
00
NOT USE
not used
01
PCMMC
Connects PCMMC
02
SMDR
SMDR print
03
UCD REPT
UCD report
04
UCD/SMDR
UCD report and SMDR print
05
CTI
Connects CTI
06
CTI/SMDR
Connects CTI with SMDR data
07
CTI/UCD
Connects CTI with UCD data
08
CTI/S/U
Connects CTI with SMDR data and UCD data
09
TRAFFIC
Call Traffic data print
10
TRF/SMDR
Call Traffic data and SMDR print
11
ALARM
System Alarm report
12
ALM/TRAF
System Alarm data and Call Traffic data print
13
PERI UCD
Periodic UCD report
16
HM REPT
Hotel/Motel report(Hotel/Motel related)
17
PMS
PMS data print(Hotel/Motel related)
18
PMS SMDR
PMS data and SMDR print(Hotel/Motel
related)
19
BD-PMS
Connects Bi-directional PMS
(Hotel/Motel related)
27
UCD VIEW
UCD view data print(MMC 860 enabled only)
28
UV/SMDR
UCD view data and SMDR print
(MMC 860 enabled only)
29
UV/CTI
Connects CTI with UCD view
(MMC 860 enabled only)
30
1
REMO M/A
BAUD
0: 4800 bps
[Baud Rate(Speed)]
1: 9600 bps
Connects Remote M & A
2: 19200 bps
3: 38400 bps
2-320
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
No
2
3
Option
Description
CHAR LENG
7: 7 bits
(Character Length)
8: 8 bits
PARITY
0: NONE
(Parity Bit)
1: ODD
2: EVEN
4
RETRY COUNT
01-99
(4 Retry count)
5
STOP BIT
1: 1 BIT
2: 2 BIT
6
7
WAIT TIME
0-99900 ms for ENQ/ACK, 0-3600 sec for NORMAL
DTR CHECK
0: NONE
(Disconnect check
1: ODD
on/off)
2: EVEN
CONDITIONS
NONE
DEFAULT DATA
SERVICE PORT 2: PCMMC
PORT 3: SMDR
BAUD RATE: 19200 BPS
CHAR LENGTH: 8 BITS
PARITY: NONE
RETRY COUNT: 03
STOP BIT: 1 BIT
WAIT TIME: 03000 MSEC or 30 SEC
DTR CHECK: OFF
© SAMSUNG Electronics Co., Ltd.
2-321
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 804.
Display shows:
SYS I/O PORT (1)
2. Enter desired port via dial keypad.(e.g., 2)
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
SYS I/O PORT (2)
3. Enter desired parameter via dial keypad.(e.g., 1)
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
SYS I/O PORT (2)
4. Enter parameter data via dial keypad.
OF
Press Volume button to make selection and
press Right Soft button to return to step 2.
SYS I/O PORT (2)
SERVICE:PC-MMC
SERVICE:SMDR
BAUD:9600 BPS
BAUD:19200BPS
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 725
MMC 860
2-322
SMDR OPTIONS
UCD VIEW
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[805] LEVEL AND GAIN
Allows the system administrator to set the base level of the TX volume on phones system
wide. There are eight(8) levels those are able to be controlled by the Volume button on
phone. And maximum controllable levels in the system are ten(10). Phone station users can
vary eight levels. So this MMC gives the most flexibility to the system administrator so he
can classify any desired eight(8) levels within eleven(11).
No
Option
0
TX LEVEL CONTROL
Description
Adjusts the transmitting sensitivity(Max.: 9) Default values are
followed:
1
MISC TSW GAIN
INDEX:
0
1
2
3
4
5
6
7
LEVEL:
0
1
2
4
3
5
6
7
Adjusts the level of the internal music source of the MCP card or
the external music source of the MISC card.(0~7, higher numbers
mean lower levels) Default value is 0.
2
TSW GAIN
Adjusts the tone sensitivity(As shown below, there are 8 types of
CONTROL
matrix connections of the T-Switch that adjusts the tone sensitivity.
Connection between Trunk lines are only applicable when set as 0
in MMC 421.)
0
DGP
DLI phone
1
SLT
SLI phone
2
ATRK Analog trunk
3
DTRK Digital trunk
4
DECT DECT terminal
5
VOIP MGI port or IP-based phone
6
SVMi SVMi port
7 WLAN WIP port
When changing the MMC [805]
‘MMC [805] LEVEL AND GAIN’ should not be changed from the default levels
without the assistance of the local SAMSUNG distributor.
CONDITIONS
NONE
© SAMSUNG Electronics Co., Ltd.
2-323
CHAPTER 2. MMC Programming
DEFAULT DATA
RX
DGP
SLT
ATRK
DTRK
DECT
VOIP
SVMi
WLAN
DGP
0.0
0.0
0.0
0.0
-6.0
0.0
-6.0
+1.9
SLT
0.0
-2.5
0.0
-2.5
-6.0
0.0
-6.0
+1.9
ATRK
0.0
0.0
+1.9
-6.0
-6.0
0.0
-6.0
+1.9
DTRK
0.0
-2.5
+1.9
0.0
-6.0
0.0
-6.0
0.0
DECT
0.0
0.0
0.0
+1.9
-6.0
0.0
-6.0
0.0
VOIP
0.0
0.0
0.0
0.0
-6.0
0.0
-6.0
0.0
SVMi
0.0
0.0
0.0
0.0
-6.0
0.0
-6.0
0.0
WLAN
-6.0
-2.5
-6.0
0.0
0.0
0.0
0.0
+1.9
TX
ACTION
DISPLAY
1. Press Transfer button and enter 805.
Display shows:
TX LEVEL CONTROL
2. Press Volume button to make selection.(0-3)
After selection is made, press Right Soft button
to move cursor.
TX LEVEL CONTROL
3. When the TX LEVEL CONTROL is selected.
a. Select the desired volume level via dial keypad.
OR
Press Volume button to go to the next volume level
and press Right Soft button.
b. Enter desired volume data via dial pad.
OR
4. When the MISC TSW GAIN is selected.
a. Enter desired MISC/BGM TSW gain via dial keypad.
OR
Press Volume button to select desired MISC/BGM
TSW gain and press Right Soft button.
2-324
LEVEL 0 0
LEVEL 1 1
TX LEVEL CONTROL
LEVEL 1 1
TX LEVEL CONTROL
LEVEL 1 3
MISC TSW GAIN
BGM/MOH :0
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
5. When the TSW GAIN CONTROL is selected.
a. Select the TX TSW connect type via dial button pad.
OR
Press Volume button to go to the next TX TSW
connect type and press Right Soft button.
TSW GAIN CONTROL
SLT DGP :+0.0
b. Select the RX TSW connect type via dial button pad.
OR
Press Volume button to go to the next RX TSW
connect type and press Right Soft button.
TSW GAIN CONTROL
c. Enter desired TSW gain control data via dial pad.
OR
Press Volume button to scroll data and press
Right Soft button.
TSW GAIN CONTROL
SLT ATRK:+0.0
SLT ATRK:+1.9
7. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-325
CHAPTER 2. MMC Programming
[806] CARD PRE-INSTALL
Allows the preprogramming of a card slot for a specific board type. A board inserted into a
system will not be recognized by the system until it is ENABLED using this MMC. Cards
installed using MMC 806 will NOT be assigned in the system numbering plan. You must
then use MMC 724 to assign the desired directory numbers to extensions, trunks, AA, ports
or miscellaneous functions. This MMC also shows which PSU is powering the card
selected.
POWER STATUS
N: 48V Power does not used.
A: 1st Power is used.(1st Power type = PSU 60)
B: 2nd Power is used.(2nd Power type = PSU 60)
1: 1st Power is used.(1st Power type = PSU-B)
2: 2nd Power is used.(2nd Power type = PSU-B)
[xx]: The maximum port count which 48 V power is supplied.
When a card is removed and a different type card is inserted
If a card is removed and a different type card is inserted and this MMC is
performed, the memory associated with that card(e.g., key programming, etc.) will
be erased.
CONDITIONS
NONE
DEFAULT DATA
NONE
2-326
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
ACTION
DISPLAY
1. Press Transfer button and enter 806.
Display shows:
C:1 S:1
P:1[16]
2. Press Volume button to make selection
(e.g., Cabinet 1) and press Right Soft button.
C:1 S:1
P:1[16]
3. To select which slot to address press
Volume button to make selection.
OR
Use the dial pad to make a selection(e.g., Slot 6)
and press Right Soft button.
C:1 S:6
P:2[16]
4. Press Volume button to make selection or use
the DIAL to select.(1: yes 0: no)
C:1 S:6
P:2[16]
5. Press Volume button to make selection or use
the DIAL to select(1:1 yes 0: no)
and press Right Soft button to return to Step 1.
Continue to add cards as shown in step 2.
OR
Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
C:1 S:6
P:2[16]
8 DLI 8 DLI
8 DLI 8 DLI
16 DLI 16 DLI
RESET CARD ? NO
ARE YOU SURE?NO
RELATED ITEMS
MMC 724
© SAMSUNG Electronics Co., Ltd.
DIAL NUMBERING PLAN
2-327
CHAPTER 2. MMC Programming
[807] PHONE VOLUME CONTROL
Allows the system administrator to set the level of phone volume.
Level of Phone Volume
No
0
Type
KEY TONE VOL
FX
No
0
Type
LINE VOLUME
SPEAKERER VOLUME
1
SIDETONE VOL
1
NOR.LP ATTEN
2
HANDSET TX
2
MIC LP ATTEN
3
MIC TX LEVEL
3
ACOU DECOUPL
4
NOISE GUARD
4
ELEC DECOUPL
5
NOISE THRES
5
T/R RATIO
6
ALC THRES
6
R/T RATIO
7
TX/RX THRES.
8
TX/RX COMP
9
MIN RX VOL(28D, 12L, 21D, ITP)
When changing the MMC [807]
‘MMC [807] PHONE VOLUME CONTROL’ should not be changed from the
default levels without the assistance of the local SAMSUNG distributor.
CONDITIONS
NONE
ACTION
2-328
DISPLAY
1. Press Transfer button and enter 807.
Display shows:
VOL.CONTROL:US24
2. Enter phone type via dial keypad.
OR
Press Volume button to make selection and press
Right Soft button to move cursor.
VOL.CONTROL:EU24
3. Enter volume item via dial keypad.
OR
Press Volume button to make selection and press
Right Soft button to move cursor.
VOL.CONTROL:EU24
KEY TONE VOL:1
KEY TONE VOL:1
SIDETONE VOL:1
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
4. Enter volume data via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to save and return step 3.
VOL.CONTROL:EU24
HANDSET TX
:6
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
DEFAULT DATA
DEPEND ON PHONE TYPE
21D
Type
KEY TONE VOL
FX
Default
1
Type
LINE VOLUME
SPEAKERER VOLUME
Default
3
14
SIDETONE VOL
1
NOR.LP ATTEN
4
HANDSET TX
4
MIC LP ATTEN
5
MIC TX LEVEL
3
ACOU DECOUPL
8
NOISE GUARD
8
ELEC DECOUPL
8
NOISE THRES
1
T/R RATIO
2
ALC THRES
7
R/T RATIO
2
TX/RX THRES.
3
TX/RX COMP
5
MIN RX VOL
6
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-329
CHAPTER 2. MMC Programming
[809] SYSTEM MMC LANGUAGE
Allows system programmer to assign a LCD display based on system programming
language.
0. ENGLISH
1. GERMAN
2. PORTUGAL
CONDITIONS
NONE
DEFAULT DATA
ENGLISH
ACTION
DISPLAY
1. Press Transfer button and enter 809.
Display shows:
SYS.MMC LANGUAGE
2. Enter desired language number via dial button pad.
OR
Press Volume button to make selection and
press Right Soft button.
SYS.MMC LANGUAGE
ENGLISH
GERMAN
3. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-330
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[810] HALT PROCESSING
Used only in the event that all data processing needs to be stopped either in a single cabinet
slot or in the entire system.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 810.
Display shows:
HALT/PROCESSING
2. Enter cabinet selection via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to advance cursor.
HALT/PROCESSING
Press ANS/RLS button to select all cabinets
and slots.
3. Enter slot number via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to advance cursor.
C:ALL S:ALL PROC
C:1
S:ALL PROC
HALT/PROCESSING
C:ALL S:ALL PROC
HALT/PROCESSING
C:1
S:2 PROC
4. Enter 1 for HALT or 0 to PROC.
OR
Press Volume button to make selection and
press Right Soft button to enter and return to step 2.
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-331
CHAPTER 2. MMC Programming
[811] RESET SYSTEM
Provides two methods of restarting the system. The first method restarts the system and
clears all memory. The second method restarts the system only. If clear all memory is
selected, only the default data will return. Extreme care should be taken when using this
MMC. If the system is restarted, all voice/data connections are dropped. If memory is
cleared, all customer data is deleted and the system returns to defaulted status.
No
Type
Description
0
RESET SYSTEM
System reset only with Smart Media read.
1
CLEAR MEMORY
System reset and make default system with Smart Media read.
2
FAST RESTART
System reset only without Smart Media read.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 811.
Display shows:
2. Enter reset type(0-2) via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
3. Dial 1 for YES or 0 for NO.
Press Volume button to make selection and
press Right Soft button.
4. Dial 1 for YES or 0 for NO.
Press Volume button to make selection and
press Right Soft button.
5. If clear memory, system will return with default
time and date and default extension number.
OR
If system just restarted, it will return to normal
programmed status.
RELATED ITEMS
NONE
2-332
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[812] SET COUNTRY CODE
This MMC must be run by the installer before any other programming is done.
When changing the MMC [812]
‘MMC [812] SET COUNTRY CODE’ should not be used from the default levels
without the assistance of the local SAMSUNG distributor.
CONDITIONS
Allows the system installer to select system software country. If you change the country
selection, the system will be restart and all customer data returns to defaulted status
according to the selected country.
DEFAULT DATA
According to MCP2 DIP S/W.
ACTION
DISPLAY
1. Press Transfer button and enter 812.
Display shows:
SELECT COUNTRY
2. Press Volume button to make selection and
press Right Soft button.
SELECT COUNTRY
3. Press Volume button to select Yes or No and
press Right Soft button.
DEFAULTING SYSTM
Undefined
RUSSIA/CIS
ARE YOU SURE?NO
When you select ‘YES’
if you select ‘YES’, this will restart the system and all data make default.
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
ALL MMC
© SAMSUNG Electronics Co., Ltd.
2-333
CHAPTER 2. MMC Programming
[813] HOTEL OPERATION
Allows the system installer to enable the HOTEL feature.
CONDITIONS
NONE
DEFAULT DATA
DISABLE
ACTION
DISPLAY
1. Press Transfer button and enter 813.
Display shows:
HOTEL OPERATION
2. Dial 1 for ENABLE or 0 for DISABLE.
HOTEL OPERATION
Press Volume button to make selection and
press Right Soft button.
3. Dial 1 for YES or 0 for NO.
Press Volume button to make selection and
press Right Soft button.
4. Dial 1 for YES or 0 for NO.
Press Volume button to make selection and
press Right Soft button.
DISABLE
ENABLE
HOTEL OPERATION
CHANGE NOW ? NO
HOTEL OPERATION
ARE YOU SURE?NO
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
Hotel Related MMC
MMC 221
MMC 222
MMC 513
MMC 760
MMC 761
MMC 762
2-334
EXTENSION TYPE
FAX PAIR
HOTEL TIMER
ITEM COST TABLE
TAX RATE SETUP
ROOM COST RATE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[815] CUSTOMER DATABASE COPY
Provides a means to copy the customer database to the SMDB(Smart Media card Data
Base). This enables the on board database(SRAM) to be copied to the SMDB and also
allows the SMDB database to be copied to the on board database. A daily save can be
programmed to automatically save the on board data base to the SMDB. This insures that
an up to date database is always available in the case of a catastrophic failure. A daily save
time of 00:00 means there is no save performed.
It is recommended to CLEAR the SMDB before the SRAM is copied to it. When the
SRAM is copied to the SMDB there is no interruption in service. If the SMDB is copied to
the SRAM the system will reset to accept the new data.
Option
Description
SMDB
Smart Media card database
SRAM
MCP2 On-Board database
S:mm/dd/yy hh:mm
Indicates the time the database was saved to the SMDB or the time the
SRAM was last saved
DAILY SAVE hh:mm
The time the SRAM will be saved to the SMDB
A Smart Media Card of 16 MB or 32 MB
A Smart Media Card of 16 MB or 32 MB must be installed in order to copy the on
board database(SRAM) on to the Smart Media card(SMDB).
CONDITIONS
NONE
DEFAULT DATA
DAILY SAVE 00:00(no daily save)
© SAMSUNG Electronics Co., Ltd.
2-335
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 815.
Display shows:
If the Smart Media is used already, the display
shows.
2. Press Right Soft button to move cursor.
CUST DBASE:SMDB
S:12/01/01 00:00
CUST DBASE:SMDB
SMART IS BUSY
CUST DBASE:SMDB
S:12/01/01 00:00
3. Press Volume button to make selection and
press Right Soft button to move cursor.
CUST DBASE:SMDB
4. Press Volume button to select YES or NO and
press Right Soft button.
CUST DBASE:SMDB
5. Press Volume button to select YES or NO and
press Right Soft button.
CUST DBASE:SMDB
If you select YES, the display shows:
CLEAR SMDB
CLEAR SMDB
:NO
:YES
ARE YOU SURE?NO
CUST DBASE:SMDB
Cleared....
6. Press Volume button to make selection and
press Right Soft button to move cursor.
CUST DBASE:SRAM
7. Press Volume button to make selection and
press Right Soft button to move cursor.
CUST DBASE:SRAM
8. Input save time.
OR
Press Right Soft button to move cursor.
CUST DBASE:SRAM
9. Press Volume button to make selection and
press Right Soft button to move cursor.
CUST DBASE:SRAM
10.
Press Volume button to make selection and
press Right Soft button to make change and
return to the step 9.
DAILY SAVE:00:00
DAILY SAVE:00:00
DAILY SAVE:23:30
COPY TO SMDB:NO
CUST DBASE:SRAM
ARE YOU SURE?:YES
11. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-336
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[816] CONFERENCE GAIN
Provides a tool to adjust the gain or loss of stations and trunks in the conference bridge.
This is made available to allow for the adjustment of the conference bridge due to
permanent unsatisfactory Trunk Line conditions that may inhibit a satisfactory conference
bridge. Programming adjustments can be made on individual conference analog trunk
members.
Option
Description
MEMBER
This identifies which size of conference the adjustment will be made for. ie. 3, 4 or 5
party conference.
A-TRK
This identifies which analog trunk member that is being addressed.
CNF
This is the gain or loss adjustment in the conference bridge.
SW
This is the gain or loss adjustment in the time division switch.
When changing the MMC [816]
‘MMC [816] CONFERENCE GAIN’ is not to correct low volume. To be used with
the support of local SAMSUNG Electronics Co. distributor.
CONDITIONS
NONE
DEFAULT DATA
USE DEFAULT: YES
MEMBER
A-TRK
0
1
2
3
CNF
-2.5
-2.5
-2.5
SW
+0.0
+0.0
-2.5
CNF
-6.0
-6.0
-6.0
-6.0
SW
+0.0
+0.0
-2.5
-6.0
CNF
-6.0
-6.0
-6.0
-6.0
-6.0
SW
+0.0
+0.0
-2.5
-6.0
-6.0
4
5
© SAMSUNG Electronics Co., Ltd.
3
4
2-337
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 816.
Display shows:
CONFERENCE GAIN
2. Press Volume button to make selection and
press Right Soft button to make change and
to move cursor.
CONFERENCE GAIN
3. Dial 3,4 or 5.(e.g., 4 part conference bridge)
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
MEMBER:4
4. Dial 0 to 4.(e.g., 2 analog trunk member)
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
MEMBER:4 A-TRK:2
5. Press Volume button to select CNF gain and
press Right Soft button to move cursor.
MEMBER:4 A-TRK:2
6. Press Volume button to select SW gain and
press Right Soft button to save and move cursor.
MEMBER:4 A-TRK:2
USE DEFAULT :YES
USE DEFAULT :NO
CNF:-6.0
CNF:-6.0
CNF:-6.0
CNF:-6.0
A-TRK:0
SW:+0.0
SW:2.5
SW:2.5
SW:-6.0
7. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-338
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[818] PROGRAM DOWNLOAD
Change the version by downloading new version program stored Smart Media card to
MCP2, SCP2/ LCP2 or TEPRI card.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 818.
Display shows:
PGM DOWNLOAD
2. Press Volume button to select program type
and press Right Soft button to move cursor.
PGM DOWNLOAD
3. Press Volume button to select YES and
press Right Soft button to move cursor.
If you select MCP program download,
the system will restart.
LAN PGM
MPP:MPPLV203.PGM
SPP:SPP_V203.PGM
DOWNLOAD NOW?NO
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 819
© SAMSUNG Electronics Co., Ltd.
SMART MEDIA FILE CONTROL
2-339
CHAPTER 2. MMC Programming
[819] SMART MEDIA FILE CONTROL
This MMC uses display file sizes and clear file on Smart Media card.
Files included in SmartMedia are described below:
File Name
STARTUP.INI
Description
If a user designates an MCP or SCP program at MMC 818, related data are saved
in this file. This file is initially not included but is created when the above programs
are selected at MMC 818.
STARTUP.PRE
When the system is initially started, this program uses the memory of the
MCP card to load the MPP program of SmartMedia.
This program must be included to start the system.
MPPMxxx.PGM
Program for MCP2 board.
MPPLxxx.PGM
Since the MCP2 program is not installed in the MCP2 board itself, at least
one MCP2 program must be included in SmartMedia to start the system. Files
named MPPMxxxx.PGM represent programs for M-system, and those named
MPPLxxxx.PGM represent programs for L-systme. SmartMedia must include
the proper MCP2 program corresponding to the system type(L-system or Msystem).
SPPV200.PGM
LCP program. The LCP program is installed in the card itself. The one
included in SmartMedia is used for S/W version upgrade.
PRIV100.PGM
TEPRI program. The TEPRI program is installed in the card itself. The one
included in SmartMedia is used for S/W version upgrade.
DATABASE.MPP
This file is created in SmartMedia when DB is saved to SMDB by MMC 815.
Initially not included, this file is created only when SMDB is created by MMC
815.
CONDITIONS
NONE
DEFAULT DATA
NONE
2-340
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
ACTION
DISPLAY
1. Press Transfer button and enter 819.
Display shows:
STARTUP.PRE
2. Press Volume button to select program type and
press Hold button to move cursor delete selection.
MPPLV203.PGM
3. Dial 1 for YES or 0 for NO.
OR
Press Volume button to make selection and press
Right Soft button to delete file and move cursor
step 2.
MPPLV203.PGM
sz:79288 bytes
sz:6783488 bytes
DELETE FILE? NO
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 818
© SAMSUNG Electronics Co., Ltd.
PROGRAM DOWNLOAD
2-341
CHAPTER 2. MMC Programming
[820] ASSIGN SYSTEM LINK ID
This MMC is used to assign the system link ID for PRI and VoIP networking.
Up to 50 link Ids can be entered including SELF ID. In addition each Link ID is also
associated with the IP address of the MCP2 card for that system and IP address type.
Option
Description
LINK ID
System ID for networking feature.
SIGNAL G/W
System IP address for VoIP networking.
IP TYPE
System IP address type for VoIP networking. SELF system IP address
type determines ‘SYSTEM IP TYPE’ on MMC 830.
CONDITIONS
‘SELF’ represents self-node, and must be set to use the networking function. Items other
than ‘SELF’ are used for station numbers and can be omitted.
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 820.
Display shows:
SELF :LINK ID
2. Enter SELF link ID via dial keypad and
press Right Soft button.
SELF :LINK ID
3. Press Volume button to select other link ID
and press Right Soft button to mover cursor.
SYS01:LINK ID
4. Enter other link ID via dial keypad and
press Right Soft button.
SYS01:LINK ID
11
22
5. Press Transfer button and enter button to exit.
OR
Press Speaker button to advance next MMC.
DEFAULT DATA
NONE
RELATED ITEMS
MMC 821
MMC 823
MMC 824
MMC 830
2-342
ASSIGN NETWORK TRUNK
ASSIGN NETWORK COS
ASSIGN NETWORK DIAL TRANSLATION
ETHERNET PARAMETER
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[821] ASSIGN NETWORK TRUNK
Assigns the Q-signaling PRI trunk for networking. It is assigned data on a per-TEPRI card
basis.
CONDITIONS
NONE
DEFAULT DATA
NORMAL
ACTION
DISPLAY
1. Press Transfer button and enter 821.
Display shows:
[701] Q-SIG TRK
2. Enter first trunk number of PRI card.
OR
Press Volume button to make selection and press
Right Soft button to move cursor.
[701] Q-SIG TRK
3. Enter 0 for NORMAL , or 1 for Q-SIGNALING.
OR
Press Volume button to make selection and press
Right Soft button to save and move cursor.
[701] Q-SIG TRK
NORMAL
NORMAL
Q-SIGNALING
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
© SAMSUNG Electronics Co., Ltd.
2-343
CHAPTER 2. MMC Programming
[822] SET VIRTUAL EXTENSION TYPE
Assigns the virtual extension port type. The virtual extension port types are followed:
No
Type
Description
00
SLT
Emulates SLI port
01
24 BTN SET
24 buttons phone
02
12 BTN SET
12 buttons phone
03
7 BTN SET
7 buttons phone
04
6 BTN SET
6 buttons phone
05
28 BTN SET
28 buttons phone
06
18 BTN SET
18 buttons phone
07
8 BTN SET
8 buttons phone
08
38 BTN SET
38 buttons phone
09
21 BTN SET
21 buttons phone
10
14 BTN SET
14 buttons phone
11
LARGE SET
Large LCD phone
12
7 BTN LCD
7 buttons LCD phone
13
0 BTN LCD
0 button LCD phone
14
NONE
not used
CONDITIONS
NONE
DEFAULT DATA
3501-3546: SLT
3401-3480: 28 BTN SET
ACTION
2-344
DISPLAY
1. Press Transfer button and enter 822.
Display shows:
[3501]PORT TYPE
2. Enter virtual extension number.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
OR
Press ANS/RLS button to select all.
[3502]PORT TYPE
SLT
SLT
[ALL] PORT TYPE
SLT
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
3. Enter virtual extension type.
OR
Press Volume button to make selection and
press Right Soft button to save and move cursor.
[3501]PORT TYPE
21 BTN SET
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 724
© SAMSUNG Electronics Co., Ltd.
DIAL NUMBERING PLAN
2-345
CHAPTER 2. MMC Programming
[823] ASSIGN NETWORK COS
Assigns the class of service for networking.
No
Option
Default
Description
01
CALL OFFER
Y
Call Offer
03
CC PATH RSV
Y
CC Path Reservation
04
CC SIG CONN
Y
CC Retention of Signal Connection
05
CC SVC RETN
Y
CC Service Retention
06
CCBS
N
Call Completion to Busy Subscriber
07
CCNR
N
Call Completion on No Reply
08
CFB
Y
Call Forward Busy
09
CFNR
Y
Call Forward No Reply
10
CFU
Y
Call Forward Unconditional
11
CI
N
Call Intrusion
12
CI CAPABIL
2
Intrusion Capability Level(1~3)
14
CI PROTECT
2
Intrusion Protection Level(0~3)
23
CONP LEVEL
3
CONP Level(0: none, 1: Alert, 2: Busy, 3: Both)
26
CT RE-ROUTE
N
Transfer By Rerouting
27
DND TONE
N
DND Announcement
28
DNDO
Y
Do Not Disturb Override
29
DNDO CAPABL
2
DNDO Capability Level(0~3)
30
DNDO PROTEC
2
DNDO Protection Level(1~3)
31
PAGE
Y
PAGE
32
PATH REPL.
Y
Path Replacement
33
PATH RETEN
N
Path Retention
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
2-346
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
ACTION
DISPLAY
1. Press Transfer button and enter 823.
Display shows:
NETWORK COS (01)
2. Dial the class of service number.(01-30)
OR
Press Volume button to select and press
Right Soft button to move cursor.
NETWORK COS (02)
3. Dial the feature number.
OR
Press Volume button to select and press
Right Soft button to move cursor.
NETWORK COS (02)
4. Enter 0 for NO, or 1 for YES.
OR
Press Volume button to select YES or NO and
Press Right Soft button to store data.
NETWORK COS (01)
01:CALL OFFER :Y
01:CALL OFFER :Y
03:CC PATH RSV:Y
03:CC PATH RSV:N
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 301
© SAMSUNG Electronics Co., Ltd.
ASSIGN STATION COS
2-347
CHAPTER 2. MMC Programming
[824] NETWORK DIAL TRANSLATION
Assigns the digit translation table used for networking. Generally under networking
condition, you must dial the node ID and extension number to call the another node
extension. It’s not convenient. In this MMC, the system provides the easy digit translation
of NETWORK LCR DIAL number. The translated digits are works like as LCR plus
translated digits. Using this MMC, you only dial the another node extension number and
call the another node extension simply. The system provides 96 entry of network dial
translation.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
2-348
DISPLAY
1. Press Transfer button and enter 824.
Display shows:
01:601
2. Dial the entry number.
OR
Press Volume button to select and press
Right Soft button to move cursor.
01:601 _
3. Enter digit string(max. 8digits) and press
Right Soft button to move cursor.
01:601 60201
4. Enter the minimum number of user dialled digits.
OR
Press Volume button to select and press
Right Soft button to move cursor.
01:601 60201
5. Enter the waiting number of dial until LCR
is operated.
OR
Press Volume button to select and press
Right Soft button to move cursor.
01:601 60201
SIZE:0
SIZE:0
MAX:00
MAX:00
SIZE:0 MAX:00
SIZE:3 MAX:00
DISP:N MBX:N
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
6. Enter YES/NO to display other node extension
like as a internal extension number format.
OR
Press Volume button to select and press
Right Soft button to move cursor.
01:601 60201
7. Enter YES/NO to assign Mail Box for
remote extension automatically.
OR
Press Volume button to select YES/NO and
press Right Soft button to move cursor.
01:601 60201
DISP:Y
MBX:N
DISP:Y MBX:N
8. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 710
MMC 724
MMC 820
© SAMSUNG Electronics Co., Ltd.
LCR DIGIT TABLE
DIAL NUMBERING PLAN
ASSIGN SYSTEM LINK ID
2-349
CHAPTER 2. MMC Programming
[825] ASSIGN NETWORKING OPTION
Assigns the options used for networking.
No
0
Option
ADD NUMBER TO NAME
Description
Assign to includes the extension number in the name field of
Q-SIG standard message.
1
USE REMOTE VM
2
REMOTE VM NUMBER
Assign to use SVMi on remote system.
Assign to access number of remote SVMi when the Remote
VM is used .
3
REMOTE CID NUMB
Assign to use delete node number when CID number send to
SVMi.
4
USE REMOTE ATTN
5
REMOTE ATTN NUMB
Assign to use Attendant on remote system.
Assign to access number of remote Attendant when the
Remote Attendant is used.
CONDITIONS
NONE
DEFAULT DATA
ADD NUMB TO NAME: YES
USE REMOTE VM: NO
REMOTE VM NUMBER: NONE
REMOTE CID NUMB: YES
ACTION
DISPLAY
1. Press Transfer button and enter 825.
Display shows:
ADD NUMB TO NAME
2. Dial the option number.
OR
Press Volume button to select and press Right
Soft button to move cursor.
USE REMOTE VM
3. Dial 1(YES) or 0(NO).
OR
Press Volume button to select YES/NO and
press Right Soft button to mover cursor.
USE REMOTE VM
YES
NO
YES
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
2-350
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
RELATED ITEMS
MMC 710
MMC 724
MMC 820
MMC 824
© SAMSUNG Electronics Co., Ltd.
LCR DIGIT TABLE
DIAL NUMBERING PLAN
ASSIGN SYSTEM LINK ID
NETWORK DIAL TRANSLATION
2-351
CHAPTER 2. MMC Programming
[826] ASSIGN SYSTEM REFERENCE CLOCK
The system clock may be synchronized with a external clock source from TEPRI card, PRI
card or BRI card or use the internal clock source.
CONDITIONS
In this MMC, you can select to use internal clock source and assign the system clock
source priority when the external clock source is used. The external clock source of TEPRI
card, PRI card or BRI card only can be selected.
DEFAULT DATA
PRIORITY 1: C1-S1
PRIORITY 2: C1-S2
PRIORITY 3: C1-S3
PRIORITY 4: C2-S1
PRIORITY 5: C2-S2
PRIORITY 6: C2-S3
PRIORITY 7: C3-S1
PRIORITY 8: C3-S2
PRIORITY 9: C3-S3
ACTION
DISPLAY
1. Press Transfer button and enter 826.
Display shows:
REFERENCE CLOCK
2. Dial the priority number.(1-9 or 1-3 )
OR
Press Volume button to select and press
Right Soft button to move cursor.
REFERENCE CLOCK
3. Dial the priority data.
OR
Press Volume button to select and Press
Right Soft button to store.
REFERENCE CLOCK
PRIORITY 1:C1-S1
PRIORITY 1:C1-S1
PRIORITY 1:C1-S1
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-352
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[829] LAN PRINTER PARAMETER
This program sets the various parameters required for printing to a LAN connected device.
The eight types of data listed below can be displayed using the LAN printer.
01
02
03
04
05
06
07
08
SMDR
UCD REPORT
TRAFFIC REPORT
ALARM REPORT
UCD VIEW
PERIODIC UCD
HOTEL REPORT
PMS
The items that are set in this program are listed below.
No
Option
00
DATA TYPE
01
CURR STATUS
OFF
Current status of the LAN printer
02
EMPTY BUFF
NO
Prints all data left in the buffer
03
UPDATE LAN
NO
Applies modified items
04
DESTINATION
OFF
Data transmit destination(Off, Printer, PC, Both)
05
PRINTER IP
200.1.1.1
The IP address of the LAN printer
06
PRINTER TCP
10010
The TCP port of the printer
07
LAN TCP
10020
LAN TCP port
08
RETRY COUNT
03
Re-transmit attempt count(00~10)
09
RETRY WAIT
010 sec
Wait time for re-transmit(005~250 sec)
10
PJL ENABLE
FALSE
Sets PJL(0. FALSE, 1. TRUE)
11
LANGUAGE
RAW
Printer language(0. RAW, 1. PCL, 2. PS)
12
PAPER SIZE
A4
Paper size(0. A4, 1. LETTER)
13
FONT TYPE
COURIER
Font type(0.COURIER, 1.TIMES NEW ROMAN)
14
DUPLEX ENAB
FALSE
Sets duplex(0. FALSE, 1. TRUE)
15
ORIENTATION
PORTRAIT
Orientation(0. PORTRAIT, 1. LANDSCAPE)
16
PRINT TRAY
DEFAULT
Printer tray(0.Default, 1.Tray1, 2.Tray2, 3.Manual)
17
RESOLUTION
300
Resolution(0.300, 1.600)
18
LINE/PAGE
60
Line per page
© SAMSUNG Electronics Co., Ltd.
Default
Description
Type of data to be displayed
2-353
CHAPTER 2. MMC Programming
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
ACTION
DISPLAY
1. Press Transfer button and enter 829.
Display shows:
[01] DATA TYPE
2. Enter type of data to be printed.
OR
Press Volume button to select the type and press
Right Soft button to move the cursor.
[02] DATA TYPE
3. Enter the item number.
OR
Press Volume button to select the item and press
Right Soft button to move the cursor.
[02] PRINTER IP
4. Select the data.
OR
Press the Volume button to select the data and
press Right Soft button to move the cursor.
[02] PRINTER IP
SMDR
UCD REPORT
200. 1. 1. 1
168.219. 83.101
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-354
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[830] ETHERNET PARAMETERS
This MMC provides a mean to configure the Internet Protocol(IP) addressing of the
OfficeServ 500 system MCP2 card. This MMC must be utilized if there are ITP series
phones and/or MGI cards used on the system.
No
Parameter
Description
00
SYSTEM IP ADDR
Specifies the IP address for the MCP2 card.
01
SYSTEM
Specifies the designated gateway IP address used for contacting
GATEWAY
IP devices beyond the local network subnet.
SYSTEM NET
Specifies the IP subnet mask.
MASK
This parameter is used by the system to calculate the range of IP
02
devices(subnet) that are within ‘direct reach’ of the MCP2(without
having to go through the designated network IP gateway).
03
SYSTEM RESET
Prompt to restart system MCP2 when system IP address is
changed. This reset is same to FAST RESTART on MMC 811.
04
SYSTEM IP TYPE
Defines which IP addressing relationship is used for
communications to and from the MCP2 card.
0
PRIVATE IP ONLY: The system assumes all IP phones and
VoIP connections are on the same network. And all IP
addresses are private IP address.
1
PRIVATE w PUBLIC: The system knows that there is a mixture
of IP phones and VoIP connections on the same network and
on remote network(s), thus communicates accordingly based
upon the entries in MMC 840(for IP phones), MMC 838(for
other VoIP gateways) or MMC 830(for other MCP2).
2
PRIVATE IP ONLY: The system assumes all IP phones and
VoIP connections are on the same network. And all IP
addresses are public IP address.
05
SYSTEM PUBLIC
The MCP2 will originate communications, to IP phones and VoIP
IP
connections outside the local network, using this IP address.
Communications to/from this IP will require involvement of the
MGI card. The system identifies communications to/from this
address as ‘public’. This allows devices, on remote
networks/subnets, to establish communications with the system,
without exposing your LAN. See ‘SYSTEM IP TYPE’.
06
07
SYSTEM MAC
For your reference, and cannot be changed. The unique
ADDR
hardwareMAC) address of the MCP2 card.
PCMMC ADDRESS
When system wants connect to PCMMC, system will be send to
this IP address for connection message. Reserved for future use.
08
REMOTE M/A
When system wants connect to remote M & A PC, system will be
ADDR
send to this IP address for connection message. Reserved for future
use.
© SAMSUNG Electronics Co., Ltd.
2-355
CHAPTER 2. MMC Programming
ETHERNET PARAMETERS
- The first 3 parameters: SYSTEM IP ADDR, SYSTEM GATEWAY, and SYSTEM
NET MASK are stored separate from the main system database, thus will not be
defaulted when MMC811 ‘CLEAR MEMORY’ is performed. Furthermore, any
changes to these parameters will not be applied until the MCP2 is reset.
- When changing any IP address/value, listed below, three digits must be input for
each(octet) field. Example 192.168.1.10 input must be: 192 168 001 010
CONDITIONS
This MMC must be utilized if there are ITP series phones and/or MGI cards used on
the system.
After changing the Ethernet parameter, restart the system to apply the new setting.
DEFAULT DATA
SYSTEM IP ADDR: 165.213.97.185
SYSTEM GATEWAY: 165.213.97.1
SYSTEM NET MASK: 255.255.255.0
SYSTEM RESET: NO
SYSTEM IP TYPE: PRIVATE IP ONLY
SYSTEM PUBLIC IP: 1.1.1.1
SYSTEM MAC ADDR: CARD DEPENDANT
PCMMC ADDRESS: 168.219.1.101
REMOTE M/A ADDR: 168.219.1.102
ACTION
2-356
DISPLAY
1. Press Transfer button and enter 830.
Display shows the system IP address:
SYSTEM IP ADDR
2. Press Volume button to make selection and
Press Right Soft button to move cursor.
SYSTEM IP ADDR
3. Using the keypad enter three digit IP octet numbers
IE 192 168 001 010 for 192.168.1.10.
Cursor will return to Step 1 upon completion
of IP address entry.
SYSTEM IP ADDR
4. Press Volume button to make selection and
Press Right Soft button to move cursor.
SYSTEM GATEWAY
165.213. 97.185
165.213. 97.185
192.168.001.010
165.213. 97.
1
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
5. Using the keypad enter three digit IP octet numbers
IE 192 168 001 001 for 192.168.1.1.
Cursor will return to Step 5 upon completion
of system gateway entry.
SYSTEM GATEWAY
6. Press Volume button to make selection and
press Right Soft button to move cursor.
SYSTEM RESTART
7. Press Volume button to make selection and
press Right Soft button to store and move cursor.
SYSTEM RESTART
192.168.001.001
ARE YOU SURE? NO
ARE YOU SURE? NO
8. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 61
MMC 831
MMC 833
MMC 838
MMC 840
MMC 841
© SAMSUNG Electronics Co., Ltd.
MGI GROUP
MGI PARAMETERS
VOIP ADDRESS TABLE
PRIVATE IP ADDRESSES
IP SET INFO
SYSTEM IP OPTIONS
2-357
CHAPTER 2. MMC Programming
[831] MGI PARAMETERS
This MMC provides a mean to configure the Internet Protocol(IP) addressing of the MGI
card(s). This MMC must be utilized MGI card(s) used on the system.
No
Parameter
Description
0
IP ADDRESS
Specifies the IP address for the MGI card.
1
GATEWAY
Specifies the designated IP gateway address used for contacting IP
devices beyond the local subnet.
2
SUB MASK
Specifies the IP subnet mask. This parameter is used by the system to
calculate the range if IP devices(subnet) that are within ‘direct reach’ of the
MGI(without having to go through the designated network IP gateway).
3
IP TYPE
Defines which IP addressing relationship is used for communications
to and from the MGI card.
4
PUBLIC IP
0
PRIVATE IP ONLY
1
PRIVATE w PUBLIC
2
PRIVATE IP ONLY
The MGI will originate communications, to IP phones and VoIP
connections outside the local network, using this IP address. If this IP
address sets 0.0.0.0, 255.255.255.255 or default value then this MGI
card uses private IP only. See System IP Type on MMC 830.
5
VERSION
6
MAC ADDR
No entry required. Used to indicate revision of MGI3 S/W.
For your reference, and cannot be changed. The unique hardware(MAC)
address of the MGI card.
7
CARD RESET
Prompt to restart MGI card when IP address is changed. This use for
MGI 1 and 2 only, MGI3 is self restart automatically.
MGI PARAMETERS
- The first 3 parameters: IP ADDRESS, GATEWAY, and SUB MASK-changes to
these parameters will not be applied until the MGI is reset.
- When changing any IP address/value, listed below, three digits must be input for
each(octet) field. Example 192.168.1.10 input must be: 192 168 001 010
CONDITIONS
This MMC cannot be accessed unless there is an MGI card installed in the system.
2-358
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
DEFAULT DATA
IP ADDRESS: 1.1.1.1
GATEWAY: 1.1.1.1
SUB MASK: 255.255.255.0
IP TYPE: PRIVATE IP ONLY
PUBLIC IP: 1.1.1.1
VERSION: V4
CARD RESET: NO
ACTION
DISPLAY
1. Press Transfer button and enter 831.
Display shows the first MGI card:
[3801] IP ADDRESS
2. Enter MGI number.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
[3801] IP ADDRESS
3. Enter MGI parameter number.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
[3801] IP ADDRESS
4. Enter MGI parameter.
OR
Press Right Soft button to move cursor.
[3801] IP ADDRESS
168.219. 76.101
168.219. 76.101
168.219. 76.101
165. 10.
1.100
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 615
MMC 830
MMC 838
MMC 840
MMC 841
© SAMSUNG Electronics Co., Ltd.
MGI GROUP
ETHERNET PARAMETERS
PRIVATE IP ADDRESSES
IP SET INFORMATION
SYSTEM IP OPTIONS
2-359
CHAPTER 2. MMC Programming
[832] VOIP ACCESS CODE
Provides a means to apply the Internet Protocol(IP) address to the VoIP gateway.
This MMC also assigns the number of channels that can be used for IP faxes.
TABLE(00~62): Outbound or Inbound table use for specific access codes. Usually when
the MCP2 card is used as a VoIP gateway the Outbound table is used. The Inbound table is
used to determine the number of digits to receive before processing the call. Each table has
63 entries(00~62).
No
Option
Description
0
ACCESS DGT
This is the access code that is used once the VoIP gateway is accessed;
this directs a call based on the routing tables used. An access code table
then references an access code and correlates an IP address to the
access code for routing. A maximum of 8 digits are available.
1
DGT LENGTH
This field requests the number of digits that are expected to be received
to make up the whole access code.
2
DEL.LENGTH
This is the number of digits to delete after receiving the access code. If
no digits are deleted the access code will be sent as part of the call to the
destination to continue routing at the far end destination.
3
INSERT DGT
This is the digit(s) to insert for routing at the destination. This can be used
when different numbering plans exist or if a dial 9 access is needed to be
inserted in the dialled digits.
4
IP TABLE 1
This is the first table referenced for routing the access code to an IP
address. The system has 64 IP tables(00~63) with 16 entries(00~15) in
each table. See MMC 833.
5
IP START
This entry indicates where in a table to start looking for an IP code to
associate with the access code. This can be used to manage where to
start looking for an IP address in high traffic VoIP gateway applications.
Example: If IP address routing to the desired destination is known to be
in the last 7 entries of a table the IP START location would be 8. IP
address searching would start at entry 8.
6
GK USE
This parameter determines whether a H.323 Gatekeeper will be utilized
to establish this connection.
CONDITIONS
NONE
DEFAULT DATA
ACCESS DGT: 00~09(digits 0~9), 10~62 NONE
DGT LENGTH: 1
DEL.LENGTH: 1
INSERT DGT: NONE
2-360
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
IP TABLE 1: 00
IP START: NONE
GK USE: NO
ACTION
DISPLAY
1. Press Transfer button and enter 832.
Display shows the outbound and first access
code.
(O:00)ACCESS DGT
2. Enter 0 for O(outbound) or 1 for I(inbound)
code table.
OR
Press Volume button to make select ion and press
Right Soft button to move cursor.
(O:00)ACCESS DGT
3. Enter access code table number(00-62) via dial
keypad.
OR
Press Volume button to make select ion and press
Right Soft button to move cursor.
(O:01)ACCESS DGT
4. Enter access code item(0-6) via dial keypad.
OR
Press Volume button to make select ion and press
Right Soft button to move cursor.
(O:01)ACCESS DGT
5. Enter access code data via dial keypad.
OR
Press Volume button to make select ion and press
Right Soft button to save and move cursor.
(O:01)ACCESS DGT
0
0
1
1
840
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 833
MMC 834
MMC 836
MMC 837
© SAMSUNG Electronics Co., Ltd.
VOIP ADDRESS TABLE
H.323 OPTIONS
H.323 GATEKEEPER OPTIONS
SIP OPTIONS
2-361
CHAPTER 2. MMC Programming
[833] VoIP IP TABLE
This MMC provides the IP addresses in tables pointed to by the VoIP code entry(MMC832).
There are 63 tables with up to 16 entries each. The destination IP address is required to
route dialled digits based on the access code and digits dialled. The IP entry field is divided
into 4 sections allowing modification of separate IP address fields.
When changing IP
When changing any IP address/value, listed below, three digits must be input for
each(octet) field. Example 192.168.1.10 input must be: 192 168 001 010
CONDITIONS
NONE
DEFAULT DATA
TB(00) ENTRY(00): MMC830 SYSTEM IP ADDR
ALL OTHERS: EMPTY
ACTION
DISPLAY
1. Press Transfer button and enter 833.
Display shows the first table number:
TB(00)
ENTRY (00)
2. Enter table number(00-62) via dial keypad.
OR
Press Volume button to make select ion and
press Right Soft button to move cursor.
TB(00)
ENTRY (00)
3. Enter entry number(00-15) via dial keypad.
OR
Press Volume button to make select ion and
press Right Soft button to move cursor.
TB(00)
ENTRY (00)
4. Enter IP address via dial keypad.
Cursor will be return step 3.
TB(00)
ENTRY (00)
0.
0.
0.
0.
0.
0.
0.
0.
0.
0
0
0
165.213. 87.110
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
2-362
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
RELATED ITEMS
MMC 830
MMC 832
MMC 834
MMC 837
MMC 838
© SAMSUNG Electronics Co., Ltd.
ETHERNET PARAMETER
VOIP OUTBOUND DIGITS
H.323 OPTIONS
SIP OPTIONS
PRIVATE IP ADDRESSES
2-363
CHAPTER 2. MMC Programming
[834] H.323 OPTIONS
This MMC provides various VoIP support options. The options set in this MMC are set
system-wide.
No
00
Parameter
GATEWAY CALL ID
Description
Default
This a up to 12 digits numeric entry that identifies
1234
this system.
01
H.323 FAST SETUP
Enables or disables the H.323 Fast Start call setup
ENABLE
method.
02
CALLER ID TYPE
This option controls the calling party identification
ANI
type. There are 3 possible selections :
0
GWID: Which shows the gateway call ID.
1
ANI: Which shows the calling station number
2
IP: Which shows the calling H.323 gateway IP
address.
06
TUNNELING
Enables or disables the need for additional
ENABLE
channels using H.245 signaling. Tunneling allows
use of the H.245 signal channel with the Q.931
channel.
07
DEFAULT DIL NO
This allows programming of the default direct in
500
line number when digits are missing, or incorrect
on an inbound call.
11
CODEC AUTO NEGO
Enables or disables Auto CODEC Negotiation
ON
when the MGI is used as a H.323 gateway.
14
SIGNAL PORT
Indicate the port number for H.323 signaling and
sets a range of numbers allowed by firewall
equipment. The common and default IP path or
port used is 10000.
17
SEND CLIP TABLE
Refers to SEND CLI NUMBER(MMC323), which
1
provides calling party identification when using the
MGI as a H.323 gateway.
This provides station ID of the calling station. A
single digit value corresponding with the desired
table in MMC323 should be entered here. This is
only used when MMC405 value is null.
18
19
INCOMING MODE
ALLOW GW CHECK
This option selects how incoming calls are routed
FOLLOW
when the MGI is used as a H.323 gateway.
DID TRANS
0
FOLLOW TRUNK RING: Follows MMC406
1
FOLLOW DID TRANS: Follows MMC714
2
FOLLOW INCOM DGT: Follows MMC724
When using a gatekeeper, this permits the H.323
DISABLE
gateway to check for gatekeeper presence.
2-364
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
ACTION
DISPLAY
1. Press Transfer button and enter 834.
Display shows the first option:
GATEWAY CALL ID
2. Enter H.323 option number(00-19) via
dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
H.323 FAST SETUP
3. Enter H.323 option data via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
H.323 FAST SETUP
1234
DISABLE
ENABLE
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 323
MMC 405
MMC 306
MMC 714
MMC 724
MMC 832
MMC 837
© SAMSUNG Electronics Co., Ltd.
CALLING PARTY NUMBER
CO LINE TEL NUMBER
TRUNK RING ASSIGNMENT
DID NUMBER AND NAME TRANSLATION
DIAL NUMBERING PLAN
VOIP OUTBOUND DIGITS
SIP OPTIONS
2-365
CHAPTER 2. MMC Programming
[835] MGI DSP OPTIONS
This MMC provides various MGI DSP options. The options set in this MMC are MGI-type
specific.
MGI card types are followed:
No
0
Parameter
MGI3
Description
Supports maximum 16 channels G.711, G.723.1, G.729, G.729A or
T.38. Default 8 channels and 8 channels on option board.
1
MGI2
Supports 16 channels G.711 or G.729.A
2
MGI1
Supports 16 channels G.711 only
MGI3 parameters are followed:
No
00
Parameter
CODEC-FRAME
Description
Default
Selects which audio CODEC compression will be used
G.729A –
and the transmission interval time of VoIP packets
40 Ms
generated by the MGI card. MGI3 card supports
G.729A(8 K), G.729(8 K), G.711(64 K), and
G.723.1(5.3~6.4 K).
01
ECHO CANCEL
Enables or disables echo cancellation. This function
ENABLE
removes echo that is generated by voice reflection and
packet delay.
02
SILENCE SUP
This parameter determines whether silence suppression
ENABLE
is used This prevents transmission during the silence
period of a call, and conserves bandwidth when
enabled.
03
IN FILTER
This option select input filtering of the DSP. This should
always be set as ENABLE.
04
OUT FILTER
This option select output filtering of the DSP. This
should always be set as ENABLE.
05
INPUT GAIN
PCM input gain value of DSP. The range is31~32 dB(0~63).
This set the quality of PCM voice from the VoIP DSP to
the site. Default is 32(0 dB).
06
VOICE VOL
This value selects the voice volume. The range is-
32(0 dB).
31~31 dB(0~63).
08
JITTER OPT
This is a scale value that introduces a intentional
4
buffer(delay) of the transmission of VoIP packets
generated by the MGI card. This value determines
whether the focus is on packet loss or packet delay.
The range is 00~12.
2-366
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
No
09
Parameter
MIN JITTER
Description
Decides the minimum time to consider delay for jitter
Default
30 ms
adjustment.
The range is 010~300 ms
10
MAX JITTER
Decides the maximum time to consider delay for jitter
150 ms
adjustment.
The range is 010-300 ms.
11
FAX ECM
This option selects retry of Fax-over-IP, in the case that
ENABLE
errors are detected.
12
MAX FAX CNT
This is maximum number of channels that can be
2
simultaneously utilized for Fax-over-IP. The range is
00~16.
13
DTMF TYPE
There are two types of DTMF transmission: INBAND,
which is industry standard(H.245) type DTMF transport,
and OUTBAND which is a Samsung proprietary
method.
14
TOS FIELD
An eight-bit binary value that will be utilized by external
all bits 0
routers, switches, etc(that optionally support TOS-bit
prioritization)-to identify the transport-priority value of
data packets generated by the MGI card. This value can
be left at default value(00000) if your network
infrastructure does not support this method of
bandwidth management.
15
FAX RETRY
This option selects retry count of Fax-over-IP, in the
3
case that errors are detected. The range is 0~4 and 0
means no retry.
16
RTP CHK TM
This options selects the interval time of sending RTCP.
5 SEC
MGI2 and MGI1 parameters are followed:
No
0
Parameter
CODEC FRAME
Description
Default
Selects which audio CODEC compression will be used
G.729A(MG
and the transmission interval time of VoIP packets
I2)-40 MS
generated by the MGI card. MGI2 supports G.729A(8K)
and G.711(64 K). MGI1 supports G.711 only.
1
ECHO CANCEL
This function removes echo that is generated by voice
reflection and packet delay. This sets ENABLE only,
cannot changed.
2
SILENCE SUP
This parameter determines whether silence suppression
is used This prevents transmission during the silence
period of a call, and conserves bandwidth when
enabled.
© SAMSUNG Electronics Co., Ltd.
2-367
CHAPTER 2. MMC Programming
No
4
Parameter
MIN JITTER
Description
Default
Decides the minimum time to consider delay for jitter
adjustment.
The range is 020~300 ms
5
MAX JITTER
Decides the maximum time to consider delay for jitter
adjustment.
The range is 020-300 ms.
6
DTMF TYPE
There are two types of DTMF transmission: INBAND,
which is industry standard(H.245) type DTMF transport.
This sets INBAND only, cannot changed.
7
TOS FIELD
An eight-bit binary value that will be utilized by external
routers, switches, etc(that optionally support TOS-bit
prioritization)-to identify the transport-priority value of
data packets generated by the MGI card. This value can
be left at default value(00000) if your network
infrastructure does not support this method of
bandwidth management.
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
ACTION
2-368
DISPLAY
1. Press Transfer button and enter 835.
Display shows the first option:
MGI3:CODEC-FRAME
2. Enter MGI type(0-2) via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
MGI3:CODEC-FRAME
3. Enter MGI DSP parameter via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
MGI3:CODEC-FRAME
4. Enter MGI DSP parameter.
OR
Press Volume button to make selection and
press Right Soft button to save and return step 3.
MGI3:CODEC-FRAME
G.729A –40 MS
G.729A –40 MS
G.729A –40 MS
G.729A –20 MS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 831
© SAMSUNG Electronics Co., Ltd.
MGI PARAMETERS
2-369
CHAPTER 2. MMC Programming
[836] H.323 GK OPTIONS
Provides a means to set the H.323 gatekeeper parameters for an optional external industrystandard H.323 network gatekeeper, using Registration, Admissions, and Status
signaling(RAS). The settings are system wide.
When changing IP
When changing any IP address/value, listed below, three digits must be input for
each(octet) field. Example 192.168.1.10 input must be: 192 168 001 010
No
Parameter
Description
Default
00
GK CONNECTION
This enables or disables the H.323 call to connect to
DISABLE
a gatekeeper.
01
GK ROUTING
This enables or disables routing of calls through a
DISABLE
gatekeeper.
02
GK IP ADDRESS
This is gatekeeper’s IP address.
0.0.0.0
03
GK NAME
This is alphanumeric name identifier of the
‘Gatekeeper’
gatekeeper. An entry of 16 characters.
04
This provide for an alternate gatekeeper address.
0.0.0.0
H.323 GATEWAY
This is the H.323 identifier used by the MGI when
‘OfficeServ500
ID
registering with the gatekeeper. This can be up to 32
ALTER GK IP
ADDR
05
characters.
06
E.164 GATEWAY
This is the E.164 identifier used by the H.323 trunk
NO
when registering with the gatekeeper. This can be up
-
to 16 digits in length.
07
GK KEEP ALIVE
This is the timer that the MGI uses to acknowledge
0 SEC
the presence of the gatekeeper. The range is
000~999 seconds.
08
GK DOWN ROUTE
This provides an alternate route in case the primary
PSTN
gatekeeper is down. Selections are PSTN or ALTER
GK.
09
GK RAS TYPE
Select if AUTO or MANUAL, depending on your
AUTO
gatekeeper’s capabilities.
11
12
URQ REASON
Select ON or OFF for usage of Un-register Request
MODE
RAS(URQ) messages.
RRQ FAIL TIME
Programs the time frame to re-send Registration
ON
30 seconds
Request RAS(RRQ) messages to a gatekeeper.
The range is 1~99.
13
GRQ SEND
Select ON or OFF for usage of Gatekeeper RAS
OFF
Request(GRQ) messages.
2-370
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
ACTION
DISPLAY
1. Press Transfer button and enter 836.
Display shows the first available option:
GK CONNECTION
2. Enter H.323 GK option via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
GK ROUTING
3. Enter H.323 GK option data.
OR
Press Volume button to make selection and
press Right Soft button to save and return step 3.
GK ROUTING
DISABLE
DISABLE
ENABLE
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 834
© SAMSUNG Electronics Co., Ltd.
H.323 OPTIONS
2-371
CHAPTER 2. MMC Programming
[837] SIP OPTIONS
This MMC permits the adjustments of optional Session Initiation Protocol(SIP) trunking
parameters. The MCP2 supports SIP and H.323 on a per call-per-port basis. The settings
are system-wide.
When changing IP
When changing any IP address/value, listed below, three digits must be input for
each(octet) field. Example 192.168.1.10 input must be: 192 168 001 010.
No
00
01
Parameter
Description
Default
GATEWAY
This a up to 12 digits numeric entry that identifies this
CALL ID
system.
CALLER ID
This option controls the calling party identification type.
TYPE
There are 3 possible selections:
0
GWID: Which shows the gateway call ID.
1
ANI: Which shows the calling station number(Default)
2
IP: Which shows the calling H.323 gateway IP
‘1234
-
address.
02
DEFAULT DIL
This allows programming of the default direct in line
NO
number when digits are missing, or incorrect on an
500
inbound call.
03
UDP PORT:
Sets the UDP port used on a SIP trunk call.
5060
Sets the UDP port used on a SIP phone call.
5070
RE-TRANS.
The initial re-transmission time if no answer based on the
500 ms
T1 TIME
RFC2543 specification. The range is 0~9900 ms.
RE-TRANS.
The maximum re-transmission time if no answer based
T2 TIME
on the RFC2543 specification. The range is 0~9900 ms.
RE-TRANS.
The time the User Agent Server waits after receiving the
T4 TIME
ACK message. Based on the RFC2543 specification. The
TRUNK
04
UDP PORT:
PHONE
05
06
07
4000 ms
5000 ms
range is 0~9900 ms.
08
GENERAL
The server shall retransmit the response during this
RING TM
amount of time until the requested retransmission is
5000 ms
received. For example, the wait time after sending 200
OK for INFO. The range is 0~99900 ms.
09
INVITE LING
After the client sends ACK for the INVITE Final Response, the
TM
client cannot confirm if the server received the ACK message.
5000 ms
The client waits for this amount of time after sending ACK
for the Final Response. The range is 0~99900 ms.
2-372
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
No
Parameter
Description
10
PROVISIONAL
After receiving the Provision Response, the User Agent
TIME
shall wait for this amount of time until Timeout ends. The
Default
180000 m
range is 0~999900 ms.
11
INV.NO RESP
Before sending Cancel for the Invite Request, the User
TIME
Agent shall wait for this amount of time. The range is
5000 ms
0~99900 ms.
12
GEN.NO
Before sending Cancel for General Request, the User
RESP TIME
Agent shall wait for this amount of time. The range is
5000 ms
0~99900 ms.
13
REQ.RETRY
After sending General Request, the User Agent shall wait
TIME
for the Final Response for this amount of time. The range
5000 ms
is 0~99900 ms.
14
15
SIP SERVER
Sets ENABLE or DISABLE to use an optional external
ENABLE
industry-standard SIP Server.
DISABLE
SIP SERVER
Sets SIP server IP address.
0.0.0.0.
Sets the port to use on the SIP Server.
5060
Indicate the port number for SIP signaling and sets a
-
IP
16
SIP SERVER
PORT
14
SIGNAL PORT
range of numbers allowed by firewall equipment. The
common and default IP path or port used is 10000.
18
SEND CLIP
Refers to SEND CLI NUMBER(MMC323), which provides
TABLE
calling party identification when using the MGI as a SIP
1
gateway.
This provides station ID of the calling station. A single
digit value corresponding with the desired table in
MMC323 should be entered here. This is only used when
MMC405 value is null.
19
20
INCOMING
This option selects how incoming calls are routed when
MODE
the MGI is used as a SIP gateway.
0
FOLLOW TRUNK RING: Follows MMC406
1
FOLLOW DID TRANS: Follows MMC714(default)
2
FOLLOW INCOM DGT: Follows MMC724
ALLOW GW
When using a gatekeeper, this permits the SIP gateway
CHECK
to check for gatekeeper presence.
-
DISABLE
CONDITIONS
NONE
© SAMSUNG Electronics Co., Ltd.
2-373
CHAPTER 2. MMC Programming
DEFAULT DATA
SEE DESCRIPTION
ACTION
DISPLAY
1. Press Transfer button and enter 834.
Display shows the first option:
GATEWAY CALL ID
2. Enter SIP option number(00-20) via dial keypad.
OR
Press Volume button to make selection and press
Right Soft button to move cursor.
CALLER ID TYPE
3. Enter SIP option data via dial keypad.
OR
Press Volume button to make selection and press
Right Soft button to move cursor.
CALLER ID TYPE
1234
ANI
IP
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 323
MMC 405
MMC 306
MMC 714
MMC 724
MMC 832
MMC 834
2-374
CALLING PARTY NUMBER
CO LINE TEL NUMBER
TRUNK RING ASSIGNMENT
DID NUMBER AND NAME TRANSLATION
DIAL NUMBERING PLAN
VOIP OUTBOUND DIGITS
H.323 OPTIONS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[838] PRIVATE IP ADDRESSES
This MMC is used to select which SYSTEM IP Address(PRIVATE or PUBLIC) is used to
connect other device via H.323 trunk or SIP trunk. The device which use the PRIVATE IP
Address assigned in this MMC, the PRIVATE SYSTEM IP Address will be used to connect
the device.
When changing IP
When changing any IP address/value, listed below, three digits must be input for
each(octet) field. Example 192.168.1.10 input must be: 192 168 001 010
CONDITIONS
NONE
DEFAULT DATA
TABLE(80): 165.213.255.255
ALL OTHERS: 0.0.0.0
ACTION
DISPLAY
1. Press Transfer button and enter 838.
Display shows the first table number:
PRIVATE IP
(01)
2. Enter table number(01-80) via dial keypad.
OR
Press Volume button to make select ion and
press Right Soft button to move cursor.
PRIVATE IP
(01)
3. Enter IP address via dial keypad.
Cursor will be return step 3.
PRIVATE IP
(01)
0.
0.
0.
0.
0.
0.
0
0
165.213. 87.110
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC entry.
RELATED ITEMS
MMC 830
MMC 832
MMC 834
MMC 837
© SAMSUNG Electronics Co., Ltd.
ETHERNET PARAMETER
VOIP OUTBOUND DIGITS
H.323 OPTIONS
SIP OPTIONS
2-375
CHAPTER 2. MMC Programming
[840] IP PHONE INFORMATION
This MMC provides a means to register the IP phones with the OfficeServ 500 system.
During registration, the IP and MAC addresses are also registered. The User ID and
Password must match the table entry in this MMC for the IP phone to be registered. The
system made default phone numbers are 3201~3299 and made default User ID’s match the
default station numbers(3201~3299). The system default password is 1234. IP phones must
be individually programmed with User ID and Password to register with the system.
No
00
01
Option
USER ID
USER PSWD
Description
Default
This is the ID the IP phone must match to register
first 99 IP phones
with the OfficeServ 500 system. This entry can be
are ‘3201~3299 ,
alphanumeric.
others are EMPTY
This is the Password the IP phone must also have to
‘1234
register with the OfficeServ 500 system. This entry
can be alphanumeric.
02
IP ADDR
This is the IP address of the IP phone once
0.0.0.0.
registered with the system.
This is read only data.
03
MAC ADDR
FFFFFFFFFFFF
This is MAC address of the IP phone once
registered with the system.
This is read only data.
04
SIG PORT
6000
This is the IP UDP port of the IP phone once
registered with the system. This is read only data.
This information will be needed when traversing NAT
routers, firewalls, etc.
05
VOICE PORT
9000
This is the IP RTP port of the IP phone once
registered with the system. This is read only data.
This information will be needed when traversing NAT
routers, firewalls, etc.
06
IP TYPE
This is the type of IP network used: PRIVATE or
PRIVATE
PUBLIC.
07
DSP TYPE
This selects which CODEC this phone’s DSP will use.
G.729A
G.729A(low bandwidth) or G.711(high bandwidth).
This data uses IP phone to IP phone connection
only, others case are follow MGI CODEC type.
08
PHONE TYPE
This the type of IP phone used. SAMSUNG or
SIP(future). Please should be use SAMSUNG.
09
REGIST CLR
This is used to clear the registration of a particular
IP phone. This is similar to phone
plug out and
plug in, and the useful for maintenance. Because
technician will be re-registered IP phone without
network cable find out first.
2-376
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
No
10
Option
Description
FRAME
This value determines the transmission interval time
COUNT
of VoIP packets generated by the IP phone. This
Default
10 ms
data uses case of MMC 841 ITP DSP PARA DOWN
= PHONE DATA only. The range is 10~40 ms.
11
JITTER BUF
Decides the minimum time to consider delay for jitter
20 m
adjustment. This data uses case of MMC 841 ITP
DSP PARA DOWN = PHONE DATA only.
The range is 10~90 ms.
12
TOS FIELD
An eight-bit binary value that will be utilized by
all bits 0
external routers, switches, etc(that optionally
support TOS-bit prioritization)-to identify the
transport-priority value of data packets generated by
the IP phone. This value can be left at default
value(00000) if your network infrastructure does not
support this method of bandwidth management. This
data uses case of MMC 841 ITP DSP PARA DOWN
= PHONE DATA only.
13
S/W VERSION
Display IP phone software version. This read only
data.
14
S/W UPGRADE
This is used IP phone software upgrade request
command. When this selects YES and press Right
Soft button, the system requests to IP phone
software upgrade with TFTP IP address.
15
TIME ZONE
Decides time difference of IP Phone and the system.
This is for IP Phone which is installed in the different
time area of the system.
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
© SAMSUNG Electronics Co., Ltd.
2-377
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 840.
Display shows:
[3201]USER
ID
2. Enter IP phone number via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
[3210]USER
ID
3. Enter IP phone option number via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
[3210]DSP TYPE
4. Enter option data via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to save and return step 3.
[3210]DSP TYPE
3201
3210
G.729A
G.711
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 615
MMC 616
MMC 830
MMC 831
MMC 835
MMC 841
2-378
MGI GROUP
FIXED MGI USER
ETHERNET PARAMETERS
MGI PARAMETERS
MGI DSP OPTIONS
SYSTEM IP OPTIONS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[841] SYSTEM IP OPTIONS
This MMC provides various proprietary Samsung VoIP and IP integration options.
The options set in this MMC are system-wide.
No
0
Option
PHONE VERSION
Description
Sets running IP-based phone and new phone
Default
0000
software version with the system.
0
LARGE DGP: Large LCD phone
1
LARGE ITP: Large LCD IP-based phone
2
2LINE ITP2: line LCD IP-based phone
3 WIPM APPL: Wireless IP-based mobile phone
software.
4 WIPM BOOT: Wireless IP-based mobile phone
boot program.
5
1
PHONE TFTP IP
SOFT MENU: Soft menu version
Sets phone software upgrade TFTP server IP
0.0.0.0
address.
2
ITP REGISTRATION
Defines the method that IP-based phones use to
registration themselves with the system.
0
TYPE: Defines the method that IP-based
SYS PSWD
phones use to registration themselves with the
system.
a)
SYS PSWD: System will authenticate the
IP-based phones with the value contained
within parameter ITP REGISTRATION:
PSWD within this same MMC.
b)
ITP PSWD: System will authenticate the
IP-based phones according to entries
made in MMC 840.
c)
DISABLE: System will not authenticate
IP-based phones at all.
1
PSWD: This is a system-wide password value
‘1234
used for registration of IP phones.
3
EASYSET OPTION
Sets EasySet link via LAN option with the system.
0
PSWD: This is a system-wide password value
‘1234
used for authentication of EasySet server.
1
ALIVE TIME: This is a EasySet link via LAN
0 SEC
alive check timer.
© SAMSUNG Electronics Co., Ltd.
2-379
CHAPTER 2. MMC Programming
No
4
Option
CTI LINK OPTION
Description
Default
Sets CTI link via LAN option with the system.
0
SMDR REPORT: Sets YES or NO for SMDR data
NO
to CTI link via LAN.
1
UCD REPORT: Sets YES or NO for UCD data to
NO
CTI link via LAN.
2
ALIVE TIME: This is a CTI link via LAN alive
300 SEC
check timer. If this sets 0, the system will not
check link alive.
5
ITP DSP PARA
Sets IP phone DSP parameter of system-wide.
0
M-FRAME: This value determines the
10 ms
transmission interval time of VoIP packets
generated by the IP phone. This data uses
DOWN = SYS DATA case only on this MMC.
The range is 10~40 ms.
1
JITTER: Decides the minimum time to consider
20 ms
delay for jitter adjustment. This data uses
DOWN = SYS DATA case only on this MMC.
The range is 10~90 ms.
2
TOS: An eight-bit binary value that will be
all bits 0
utilized by external routers, switches, etc(that
optionally support TOS-bit prioritization)-to
identify the transport-priority value of data
packets generated by the IP phone. This value
can be left at default value(00000) if your
network infrastructure does not support this
method of bandwidth management. This data
uses case only on this MMC.
3
DOWN: Determines data uses system-wide
SYS DATA
data or each phone data for IP-based phone
DSP control.
a)
SYS DATA: System-wide data will be
used.(MMC 841 data)
B)
PHONE DATA: Each phone data will be
used.(MMC 840 data)
6
ITP TX GAIN/HSET
Sets IP-based phone Handset TX gain value of
each level. Defaults are followed but depend on
Country
7
ITP RX GAIN/HSET
Sets IP-based phone Handset RX gain value of
each level. Defaults are followed but depend on
Country
2-380
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
No
8
Option
ITP TX GAIN/MIC
Description
Default
Sets IP-based phone MIC gain value of each level.
Defaults are followed but depend on Country
9
ITP RX GAIN/SPKR
Sets IP-based phone SPKR gain value of each
-
level. Defaults are followed but depend on Country
10
ITP VERS
Sets IP-based phone software upgrade option with
UPGRADE
the system.
0
TYPE: Sets IP-based phone software upgrade
MMC
type..
COMMAND
a)
MMC COMMAND: IP-based phone
b)
PHONE CON: IP-based phone software
software upgrades manually in MMC 840.
upgrades automatically at phone
connection.
c)
AUTO TIME: IP-based phone software
upgrades automatically at set time.
1
START TIME: IP-based phone software
0000.(Disable)
automatically upgrade start time.
2
INTERVAL: IP-based phone software
10 seconds.
automatically upgrade interval time.
11
MGI ALIVE PERIOD
Set the time interval of checking the link
-
connection of MGI card and the system.
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
ACTION
DISPLAY
1. Press Transfer button and enter 841.
Display shows the first available option:
PHONE VERSION
2. Enter option category number(0-8) via dial
keypad.
OR
Press Volume button to make select and
press Right Soft button to move cursor.
ITP REGISTRATION
© SAMSUNG Electronics Co., Ltd.
LARGE DGP: 0000
TYPE: SYS PSWD
2-381
CHAPTER 2. MMC Programming
3. Enter option number via dial keypad.
OR
Press Volume button to make select and
press Right Soft button to move cursor.
ITP REGISTRATION
4. Enter option data.
OR
Press Right Soft button to save and return
step 3.
ITP REGISTRATION
PSWD: 1234
PSWD: 8228
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
DEFAULT DATA
SEE DESCRIPTION
RELATED ITEMS
MMC 840
2-382
IP PHONE INFORMATION
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[844] IP STATION TYPE
This MMC is used to assign the IP station type(DESKTOP PHONE or MOBILE PHONE).
In default, the first half of IP station is assigned to DESKTOP PHONE and the last half is
assigned to MOBILE PHONE. To install the certain type more than the default assigned
count, user must to change the IP station type in this MMC because the maximum capacity
of IP Phone is limited. To install ITP-5012L, ITP-5014D or ITP-5021D must be set to
DESKTOP Phone. And to install WIP-5000M must be set to MOBILE PHONE.
CONDITIONS
NONE
DEFAULT DATA
[L] 001~120: DESKTOP PHONE, 121~240: MOBILE PHONE
[M] 001~060: DESKTOP PHONE, 061~120: MOBILE PHONE
ACTION
DISPLAY
1. Press Transfer button and enter 844.
Display shows:
INDEX:001 [3201]
2. Dial index number.(e.g., 121)
OR
Press Volume button to select station and press
Right Soft button to move cursor.
INDEX:121 [3301]
3. Dial 1 or 0 to select type.
(1: MOBILE PHONE, 0: DESKTOP PHONE)
Press Volume button to select option and press
Right Soft button.
INDEX:121 [3301]
DESKTOP PHONE
MOBILE PHONE
DESKTOP PHONE
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 840
MMC 846
© SAMSUNG Electronics Co., Ltd.
IP PHONE INFORMATION
WIP INFORMATION
2-383
CHAPTER 2. MMC Programming
[845] WLAN PARAMETER
This MMC modifies the WLAN parameter.
Set the network configuration with the WLAN parameters, which are the SYSTEM ID, the
System KEY, and the WBS24 and SIP related with WLAN call.
The system KEY is used internally to distinguish between systems when registering a
terminal. The default value is ‘00000 , but only when this value is modified to another
value, an electric power will be supplied to the WBS24, thus enabling the use of the
WLAN terminal, In addition, the System KEY serves as an identification ID when the
WLAN terminal connects to the WBS24.
The default value of the SYSTEM ID, ‘WBS24 , must be modified to another value in
order to use a multiple system in one area. The DNS setting for WLAN is additionally
described in this menu.
Set the network configuration for WBS24 by setting the IP assignment, Netmask, and Gateway.
These settings should be compatible with the Intranet since the network configuration setting is
essential for data service. In addition, the RF frequency for WBS24 should be selected. Currently
up to 14 frequencies may be selected.
Session Initiation Protocol(SIP) variables used for the WBS24(Basic) can be defined.
WLAN PARAMETER
No
0
Parameter
SYSTEM ID
Description
Default
ID used for distinguishing systems in wireless
WBS24
environment. Different IDs must be assigned to
different systems.
1
SYSTEM KEY
Key used for registering terminals. Different values
00000
must be assigned to each system.
2
3
4
st
1 DNS IP
2
nd
DNS IP
2
nd
WBS IP
First Domain Name Server(DNS) IP address.
0.0.0.0
Second Domain Name Server(DNS) IP address.
0.0.0.0
IP addresses of all WBSs of system used by
168.208.144. 10
wireless terminal. Different IPs must be assigned
to each system.
5
CODEC LIST
CODEC that can be used for VoIP calls between
CODEC 1: G.711a
WBS24 and terminal. G.711u, G.711a, G.726,
CODEC 2: NONE
and G.729 can all be assigned.
CODEC 3: NONE
CODEC 4: NONE
06
RF CHANNEL
Set a RF CHANNEL value that can be used by
USE CH 1: 01
WBS.
USE CH 2: 06
USE CH 3: 11
USE CH 4: 00
USE CH 5: 00
USE CH 6: 00
07
2-384
VERSION
WLAN module version.
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
No
Parameter
Description
Default
08
TFTP SERVR
WBS UPGRADE Server IP.
0.0.0.0
09
TFTP FILE
WBS UPGRADE file name.
WBS00000.TFP
18
WBS TX PWR
TX POWER of entire WBSs.
DEFAULT
19
CLR WBSREG
Initializes registration data of all WBSs.
NO
WBS PARAMETER
There are two types of WBSs, the COMBO AP and BASIC AP. A system cannot use both
types of WBSs at the same time. The AP type to be used can be set at Program 849.
Depending on the selected AP type, this program displays COMBO AP(CWBS), and
BASIC AP(BWBS).
When using COMBO AP
WBS24 COMBO is connected to a WLI card. Up to 3 WLI cards can be connected to
an L-system, and a single WLI card can be connected to a M-system.(A single WLI
card can connect up to 8 WBS24 COMBOs.)
When using BASIC AP
WBS24 BASIC is connected to the system through the network and requires an MGI
port to provide tone and call path connection.
No
Parameter
Description
Default
0
IP ADDRESS
WBS24 IP address for Ethernet.
0.0.0.0
1
GATEWAY
Gateway address of the WBS24 Network.
0.0.0.0
2
NET MASK
Netmask of the WBS24 Network.
255.255.255.0
3
MAC ADDR
MAC address of WBS24 received to the system
FFFF FFFF FFFF
when WBS24 is connected.
4
VERSION
WBS24 Software version.
5
STATUS
Alive operation status.
OFF
6
USE RF CH.
RF channel No. used by each WBS24 .
1, 6, or 11
7
TX POWER
TX POWER of each WBS.
DEFAULT
8
PARA CLR
Initializes WBS registration data.
NO
SIP PARAMETER
No
Parameter
0
RE-TRANS T1
Description
When using an unreliable transmission protocol such as UDP,
retransmission is required when no reply is received. RE-TRANS.
T1 TIME is the initial retransmission interval defined in RFC2543.
1
RE-TRANS T2
© SAMSUNG Electronics Co., Ltd.
Maximum retransmission interval defined in RFC 2543
2-385
CHAPTER 2. MMC Programming
No
2
Parameter
RE-TRANS T4
Description
RFC 2543 defines this parameter for various purposes.
For example, this parameter can be used as the time waited by User
Agent Server(USA) after receiving ACK message in an unreliable
transmission protocol.
3
GEN RING TM
When using an unreliable transmission protocol, the server cannot be
sure if the client has received the last reply.
Thus, the server must retransmit the reply for as long as this time until
it receives the requested retransmission. For example, this parameter
can be used as the waiting time after sending 200 OK for INFO.
4
INV RING TM
When using an unreliable transmission protocol, the client cannot
verify if the server has received the ACK returned to the server for the
INVITE Final Response. The client waits for as long as this time after
sending the ACK for the Final Response.
5
GEN NO RESP
Waiting time until canceling SIP related Request.
6
INV NO RESP
Waiting time until canceling SIP INVITE Request.
7
REQ RETRY
Waiting time until receiving final response for SIP related Request.
8
PROVISIONAL
On receiving Provision Response, the User Agent must wait for as
long as this time until Timeout.
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
ACTION
1. Press the Transfer button, and enter 845.
DISPLAY
WLAN : SYSTEM ID
WBS24
2-386
2. When the cursor is at WLAN, press the UP or
DOWN button and select WLAN, WBS, or SIP.
WLAN : SYSTEM ID
3. Press the Soft button and move to the SYSTEM
ID. When the cursor is below SYSTEM ID,
press the UP or DOWN button and select
the setting menu for WLAN.
WLAN : SYSTEM ID
WBS24
WBS24
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
4. Set the items below at the WLAN menu.
SYSTEM ID: Use the Soft button to move the
cursor Enter the new WLAN SYSTEM ID to
Register.
WLAN : SYSTEM ID
WBS24
Press the Soft button and proceed to next
register status.
Register the SYSTEM KEY.
WLAN : SYSTEM KEY
Register the DNS server(first) IP.
WLAN : 1ST DNS IP
Register the DNS server(second) IP.
WLAN : 2ND DNS IP
Register the 2nd WBS IP.
WLAN : 2ND WBS IP
Select the voice codec. Select from the G711a,
G711u, and G729 CODEC.
Numbers are given from 1 to 4 based on priority.
WLAN : CODEC LIST
Select the usable RF channel. Maximum 6
channels can be used for a system.
(Default RF channel: 1, 6, 11)
WLAN : RF CHANNEL
Used to change the TX POWER of all WBS.
(Default: LEVEL 1~4)
WLAN : WBS TX PWR
Used to clear registration information of all WBS.
WLAN : CLR WBSREG
5. Set the items below at the WBS24 menu.
The selected WBS is according to the MMC 848
SELECT AP TYPE.(CWBS: COMBO WBS, BWBS:
BASIC WBS)
Register the WBS24 IP ADDRESS.
Register the WBS24 NET MASK.
© SAMSUNG Electronics Co., Ltd.
00000
0.
0.
0.
0.
0.
0.
0.
0.
0.
0
0
0
CODEC 1: G.711a
USE CH 1: 01
DEFAULT
ARE YOU SURE?NO
CWBS1 : IP ADDR
0.
0.
0.
0
CWBS1 : NET MASK
255.255.255.
0
2-387
CHAPTER 2. MMC Programming
Register the WBS24 GATEWAY.
CWBS1 : GATEWAY
Displays the WBS24 MAC ADDRESS:
CWBS1 : MAC ADDR
Displays the WBS24 VERSION:
CWBS1 : VERSION
Displays the WBS24 status:
CWBS1 : STATUS
Register the WBS24 RF CHANNEL.(The WBS RF
channel must be selected among the pre-assigned
RF channels in WLAN RF CHANNELS item)
CWBS1 : RF CHAN
Register the WBS24 TX POWER.
(Default: LEVEL 1~4)
CWBS1 : TX POWER
Used to clear the WBS parameter.
CWBS1 : PARA CLR
6. Set the items below at the menu
Register the RE-TRANS T1.
The initial re-transmission time if no answer
based on the RFC2543 specification.
The range is 0-9900ms. (Default: 500 ms)
2-388
0.
0.
0.
0
FFFF FFFF FFFF
OFF
USE CH 1:01
DEFAULT
ARE YOU SURE?NO
SIP : RE-TRANS T1
000500MS
Register the RE-TRANS T2.
The maximum re-transmission time if no answer
based on the RFC2543 specification.
The range is 0-9900ms. (Default: 4000 ms)
SIP : RE-TRANS T2
Register the RE-TRANS T4 The time the User
Agent Server waits after receiving the ACK
message. Based on the RFC2543 specification.
The range is 0-9900ms. (Default: 5000 ms)
SIP : RE-TRANS T4
Register the GEN LING TM. The server shall
retransmit the response during this amount of
time until the requested retransmission is received.
For example, the wait time after sending 200 OK for
INFO. The range is 0-99900ms. (Default: 6000 m)
SIP : GEN LING TM
004000MS
005000MS
006000MS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Register the INV RING TM. After the client sends
ACK for the INVITE Final Response,
the client cannot confirm if the server received the
ACK message. The client waits for this amount of
time after sending ACK for the Final Response.
The range is 0-99900 ms. (Default: 1000 ms)
SIP : INV RING TM
Register the GEN NO RESP. Before sending Cancel
for General Request, the User Agent shall
wait for this amount of time.
The range is 0-99900 ms. (Default: 5000 ms)
SIP : GEN NO RESP
Register the INV NO RESP. Before sending Cancel
for the Invite Request, the User Agent
shall wait for this amount of time.
The range is 0-99900 ms. (Default: 5000 ms)
SIP : INV NO RESP
Register the REQ RETRY. After sending General
Request, he User Agent shall wait for
the Final Response for this amount of time.
The range is 0-99900 ms. (Default is 5000 ms)
SIP : REQ RETRY
Register the PROVISIONAL. After receiving the
Provision Response, the User Agent shall
wait for this amount of time until Timeout ends.
The range is 0-999900 ms. (Default: 180000ms)
SIP : PROVISIONAL
001000MS
005000MS
006000MS
005000MS
180000MS
RELATED ITEMS
MMC 846
MMC 847
MMC 848
MMC 849
© SAMSUNG Electronics Co., Ltd.
WIP INFORMATION
WLAN RESET AND STATUS CHECK
WLAN IP/MAC LIST
WLAN CONFIGURATION
2-389
CHAPTER 2. MMC Programming
[846] WIP INFORMATION
This MMC sets up the WIP-5000M wireless terminal’s information.
No
Parameter
Description
Default
00
REGISTERED
Shows if the terminal is registered.
NO
01
LOCATED
Shows if the terminal is connected to the system.
DETACH
02
PHONE TYPE
Shows the type of the terminal.
03
WLI NUMBER
Number of WLI connected to the WBS24
servicing the terminal.
04
WBS NUMBE
Number of WBS24 servicing the terminal.
05
IP OFFSET
Location of IP pool of the terminal IP.
06
IP ADDRESS
Terminal IP address.
0.0.0.0
07
MAC ADDR
Terminal MAC address.
0000 0000 0000
08
USER ID
User ID per terminal.
1212
09
PASSWORD
Password of terminal user.
0000
10
INSERT DGT
If 5 or more numbers are entered into the WIP
terminal, this INSERT DGT is prefixed to the
numbers, supposing that the entered numbers
do not start with a C.O. number, C.O. group
number, LCR, network LCR, or function code.
CONDITIONS
NONE
DEFAULT DATA
SEE DESCRIPTION
ACTION
1. Press the Transfer button, and enter 846.
[3301] REGIETERED
2. Dial the WIP number.
OR
Press Volume button to select station and press
Right Soft button to move cursor.
[3301] REGIETERED
3. Set the items below at the menu.
Confirm the status of terminal register for each
phone number.
2-390
DISPLAY
NO
NO
[3301] REGIETERED
NO
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
Displays the location of the registered terminal:
[3301] LOCATED
DETACH
Displays the PHONE TYPE of the registered terminal:
[3301] PHONE TYPE
Displays the WLI NUMBER of the registered
terminal:(Currently, This is not used)
[3301] WLI NUMBER
Displays the WBS NUMBER of the registered terminal:
[3301] WBS NUMBER
Displays the IP OFFSET of the registered terminal:
[3301] IP OFFSET
Displays the IP ADDRESS of the registered terminal
[3301] IP ADDRESS
Displays the MAC ADDRESS of the registered
terminal:
[3301] MAC ADDR
Register the USER ID of terminal.
[3301] USER ID
Register the PASSWORD of terminal.
[3301] PASSWORD
Register the INSERT DGT of terminal.
(These digits will be automatically inserted in
front of user dialling digits when the count of user
dialling digit is exceed 4 and it does not start with the
TRK access code and FEATURE code)
[3301] INSERT DGT
1212
_
RELATED ITEMS
MMC 847
MMC 848
MMC 849
© SAMSUNG Electronics Co., Ltd.
WLAN RESET AND STATUS CHECK
WLAN IP/MAC LIST
WLAN CONFIGURATION
2-391
CHAPTER 2. MMC Programming
[847] WLAN RESET AND STATUS CHECK
This MMC is used for rebooting the WBS24 all or independently. This MMC is also used
for initializing the WLI card.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press the Transfer button, and enter 847.
RESET :WLI :1
2. Select the item number.(0: RESET, 1: STATUS)
OR
Press Volume button to select item number and
press Right Soft button to move cursor.
RESET :WLI :1
3. Select the card type.(WLI or WBS)
RESET :WLI :1
4. Select the card number. If you press ANS/RLS
button, all WLI(or All WBS) will be selected.
RESET :WLI :2
5. Press the Soft button, or press [1] to select YES,
and the WBS will be initialized.
RESET :WLI :2
6. To verify the STATUS of WLI or WBS, select 1
to step 2.
STATUS: WLI
RESET NOW
? NO
RESET NOW ?
RESET NOW ?
RESET NOW ?
RESET NOW ?
C1S1
OFF
NO
NO
NO
NO
OFF
STATUS: CWBS:01->
Y N N N N N N N
RELATED ITEMS
MMC 846
MMC 848
MMC 849
2-392
WIP INFORMATION
WLAN IP/MAC LIST
WLAN CONFIGURATION
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[848] WLAN IP/MAC LIST
This MMC is used when viewing the IP list assigned to WLAN, or when creating a new IP
list. This IP Address is automatically assigned to WIP-5000M during new registration
procedure. If the IP Address is assigned already, the assigned terminal number will be
shown in the USED field.
Also, the MMC is used to set MAC addresses in the data terminal in order to use the
wireless LAN.(Not implemented yet)
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press the Transfer button, and enter 848.
IP:001 USED:
0. 0. 0. 0
2. Select the menu.(0: IP LIST, 1: MAC LIST)
IP:001 USED:
0. 0. 0. 0
3. Select the table number.
IP:001 USED:
4. Enter the IP ADDRESS.
IP:001 USED:
5. Numbers next to USED indicates the terminal
number from which the IP ADDRESS was
Assigned.
IP:001 USED:3301
_ 0. 0. 0. 0
168.
0.
0.
168.219.149.
0
5
RELATED ITEMS
MMC 846
MMC 847
MMC 849
© SAMSUNG Electronics Co., Ltd.
WIP INFORMATION
WLAN RESET AND STATUS CHECK
WLAN CONFIGURATION
2-393
CHAPTER 2. MMC Programming
[849] WLAN CONFIGURATION
This MMC is used to set the WLAN configuration.
Parameter
Description
REGISTER VoWLAN
Enable or disable the register of new WIP-500M mobile phone.
WIP REGIST CLEAR
Used to clear the registration of WIP. The FORCED mode clearing is used
when the device is not connected normally(ex: device broken) and the
NORMAL mode clearing can be used in normal cases.
WBS WEP SERVICE
Enable or disable the WEP(Wired Equivalent Privacy) feature .
WEP KEY
Assign the WEP key(13 characters only).
STATIC WBS IP
Select the use of Static WBS IP.
STATIC WIP IP
Select the use of Static WIP IP.
SELECT AP TYPE
Select the AP type of the system. Combo AP and Basic AP cannot be
used in simultaneously. After change the AP type, the system must
be restarted.
CONDITIONS
NONE
DEFAULT DATA
REGISTER VoWLAN: DISABLE
WIP REGIST CLEAR: DISABLE
WBS WEP SERVICE: DISABLE
WEP KEY: None
STATIC WBS IP: DISABLE
STATIC WIP IP: DISABLE
SELECT AP TYPE: BASIC AP(DEPEND ON COUNTRY)
ACTION
2-394
DISPLAY
1. Press the Transfer button, and press 849.
ENTER PASSWORD
2. Enter the PASSCODE to activate the register.
(This PASSCODE is assigned in MMC 202
WLAN REGST)
ENTER PASSCODE
3. Select ENABLE to register the terminal to the
REGISTER WLAN.
REGISTER VoWLAN
4. Select the WIP REGIST CLEAR to clear the register
status for each terminal.
WIP REGIST CLEAR
_
****
DISABLE
3301:FORCED
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
5. Select the WEP KEY setting when
ENCRYPTION is selected.
WBS WEP SERVICE
6. Enter WEP KEY values when the WBS WEP
SERVICE is enabled.(13 characters only)
WEP KEY
7. Select ENABLE to use the static WBS IP.
STATIC WBS IP
DISABLE
DISABLE
8. Select ENABLE to use the static WIP IP.
STATIC WIP IP
DISABLE
9. Select AP TYPE of the system. If you change the
AP type, the system must be restarted.
SELECT AP TYPE
COMBO AP
SELECT AP TYPE
RESET SYSTEM?NO
RELATED ITEMS
MMC 846
MMC 847
MMC 848
© SAMSUNG Electronics Co., Ltd.
WIP INFORMATION
WLAN RESET AND STATUS CHECK
WLAN IP/MAC LIST
2-395
CHAPTER 2. MMC Programming
[850] SYSTEM RESOURCE DISPLAY
This MMC is only used for system resource display. This is displayed the used resources
and the free resources. This is a READ ONLY MMC.
0. DTMFR DSP’S
1. CID DSP’S
2. R2MFC DSP’S
3. CONF GROUP’S
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 850.
Display shows:
DTMFR DSP’S
2. Enter the option number.(0-3)
OR
Press Volume button to select.
CID DSP’S
USE:000 FREE:012
USE:000 FREE:014
3. Press Transfer button and enter to exit.
OR
Press Speaker button advance to next MMC.
RELATED ITEMS
NONE
2-396
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[851] ALARM REPORTING
This MMC is used to view, store, print or clear system alarms. There are two levels of
faults displayed via alarm code, major alarms and minor alarms. Major alarms codes are
usually service affecting and require a certified technician to determine the fault. A minor
alarm indicates a fault that may or may not be service affecting and usually does not
seriously degrade the systems operating capabilities. The alarm buffer will hold up to 100
alarms on a first in-first out(FIFO) basis. Alarms will provide a date and time stamp based
on the system time. If applicable the hardware cabinet, port, and/or slot will be displayed.
If an ALARM SIO port is programmed(MMC 804) alarm information can be printed on
demand and also prints as alarm information is provided.
ALARM REPORTING OPTIONS(Select one of the options)
No
Option
Description
0
VIEW ALARM
View alarm buffer
1
OVERFLOW
Determines buffer control when buffer is full.
CONTROL
0
OVERWRITTEN: When buffer is full, the oldest entry in
1
STOP RECORDING: When buffer is full, stop recording
buffer overwritten.(Default)
alarms.
3
CLEAR ALARM BUF
Clears alarm buffer.
4
PRINT ALARM BUF
Prints contents of alarm buffer to the assigned alarm IO port.
ALARM CODE DEFINITION
See Alarm Code Definition on MMC 852.
CONDITIONS
NONE
DEFAULT DATA
NONE
© SAMSUNG Electronics Co., Ltd.
2-397
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 851.
Display shows:
SYS ALARM REPORT
2. Enter desired option.
OR
Press Volume button to make selection and press
Right Soft button to move cursor.
SYS ALARM REPORT
3. System displays the alarm count number, date
and time stamp.(uses station, configuration for
display format, date, time will be 24 hour format)
Alarm type and cause code will display.
[00] 02/18 14:30
4. Press Volume button arrows to scroll through
other alarms.
OR
Press Right Soft button to return step 2.
SYS ALARM REPORT
VIEW ALARMS
VIEW ALARMS
MNF02 C1-S02
VIEW ALARMS
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 852
2-398
SYSTEM ALARM ASSIGNMENTS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[852] SYSTEM ALARM ASSIGNMENTS
This MMC allows the assignment of system alarms to ring and display the alarms on
stations that have the Alarm Key assigned. The System Alarm Key is programmed in
Station Key Assignments(MMC 722). System Alarm key programming is tenant
wide(tenant 1 and 2). Alarms not programmed to report to the System Alarm key will still
be retained in the maintenance alarm buffer for Alarm Reporting(MMC 851). The alarm
buffer will hold up to 100 alarms on a First In-First Out(FIFO) basis. Pressing the System
Alarm key will silence the audible alarm until another alarm is generated by the system.
Alarm conditions that have multiple causes e.g., PRI errors and synchronization loss will
print all associated alarm information if an SIO port is programmed as an ALARM port.
The specific fault alarm data can be displayed via MMC 851 System Alarm Reporting.
Alarm Notification
Alarm Notification Off/On(0/1) determines if the alarm provides a visual and
audible notification to the System Alarm key station(s). Pressing the System
Alarm key and the release key will silence the audible alarm only at the station
that pressed the System Alarm key and the release key. See alarm displays table
for assignments.
Alarm Code Definition:
No
01
Code
Alarm Name
MJA--
MCP2 Error
MJA01
POR Restart
Definition
System Fault
MCP2 restart process has been executed via power on
restart(POR).
02
MJA02
Soft Restart
MCP2 restart process has been executed viA button reset.
03
MJA03
Mem Reset
The system RAM has been cleared via manual
programming(PCMMC or MMC) resulting in a system
reset.
04
MJA04
MCP Reset
The MCP2 has S/W exception error.
Alarm data = Reason
- BUS ERR: Restart Bus Error
- ADDR.ERR: Restart Address Error
- ILLEGAL: Restart Illegal opcode
- ZERO DIVID: Restart Zero divide
- PRIVILEGE: Restart Privilege Violation
- ENDL LOOP: Restart Endless Loop
05
MJA05
LCP Reset
The SCP2 or LCP2 has reset
Alarm data = Cabinet(1, 2 or 3)
06
MJA06
PCM Switching
A fault has occurred in the Switching Control
Alarm data = MCP BASE, ESM: 1, ESM: 2 or ESM: 3
© SAMSUNG Electronics Co., Ltd.
2-399
CHAPTER 2. MMC Programming
No
Code
Alarm Name
Definition
MJB--
LCP/TASK Error
LCP or TASK Fault
08
MJB01
HDLC Com Error
Communications to LCP lost or faulty.
09
MJB02
Memory Alarm 1
A RAM diagnostic check error has occurred in the
MCP2.
10
MJB03
Memory Alarm 2
A RAM diagnostic check error has occurred in the
cabinet 1 SCP2.
11
MJB04
Memory Alarm 3
A RAM diagnostic check error has occurred in the
cabinet 2 LCP2.
12
MJB05
Memory Alarm 4
A RAM diagnostic check error has occurred in the
cabinet 3 LCP2.
13
MJB06
IPC MSGQ Over
IPC TX queue full error has occurred in the MCP2.
Alarm data = IPC Queue type
(MCP-LAN, MCP-SCP, MCP-LCP1, MCP-LCP2)
14
MJB07
Task MSGQ Over
Task MSG queue full error has occurred in the MCP2.
Alarm data = Error Task
16
MJC--
DSP Error
System DSP Fault
MJC01
DTMF Fault
An abnormal interrupt has occurred in the system
DTMF resources.
Alarm data = DTMF Receiver DSP position
17
MJC02
Tone Fault
An abnormal interrupt has occurred in the system
tone resources.
Alarm data = TONE Receiver DSP position.
25
MJC10
AA-DTMF Fault
An abnormal fault reported in one of the AA card
DTMF resources.
Alarm data = Cabinet, Slot, Port(Cx-Syy-Pzz)
26
MJC11
AA-MFR Rec
An abnormal fault reported in one of the AA card
DTMF resources has recovered.
Alarm data = Cabinet, Slot, Port(Cx-Syy-Pzz)
27
MJC12
E911 Restart
The E911 card has restarted.
Alarm data = Cabinet, Slot(Cx-Syy)
28
MJC13
E911 Block
The E911 card has blocked because the system
detects the card does not work correctly.
Alarm data = Cabinet, Slot(Cx-Syy)
31
MJC16
WLI Restart
The WLI card has restarted.
Alarm data = Cabinet, Slot(Cx-Syy)
32
MJC17
WLI Block
The WLI card has blocked because the system
detects the card does not work correctly.
Alarm data = Cabinet, Slot(Cx-Syy)
2-400
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
No
Code
Alarm Name
Definition
MJD--
DTRK Error
ISDN or E1 card Fault
33
MJD01
Sync Failure
Clocking on TEPRI cards has become asynchronous.
34
MJD02
Sync Recovery
Clocking on TEPRI cards has become synchronous.
35
MJD03
Red Alarm
Locally detected loss of PCM carrier on TEPRI card for
more than 250 ms.
Alarm Data = Cabinet, Slot(Cx-Syy)
36
MJD04
Red Alarm Rec
PCM carrier detected locally on TEPRI cards.
Alarm Data = Cabinet, Slot(Cx-Syy)
37
MJD05
Yellow Alarm
Remotely detected failure transmitted in frame on
TEPRI card.
Alarm Data = Cabinet, Slot(Cx-Syy)
38
MJD06
Yellow Alarm
Remotely detected failure restored transmitted on
Rec
TEPRI card.
Alarm Data = Cabinet, Slot(Cx-Syy)
39
MJD07
Blue Alarm
All one's being transmitted on facility on TEPRI card.
Alarm Data = Cabinet, Slot(Cx-Syy)
40
MJD08
Blue Alarm Rec
A blue alarm condition has been cleared.
Alarm Data = Cabinet, Slot(Cx-Syy)
41
MJD09
Bit Error Alarm
-6
Alarm is activated when the when error rate exceeds 1x10
-6
-3
errors. Note: 1x10 is threshold for minor alarm, 1 x 10 is
threshold for major alarm errors on E1,PRI or BRI.
Alarm Data = Cabinet, Slot(Cx-Syy)
42
MJD10
NTWRK Event
An Implausible event has occurred on the PRI or BRI
Network digital line. Protocols do not match or
subscriber ID mismatch.
Alarm Data = Cabinet, Slot Cx-Syy)
43
MJD11
SPID Init Error
The BRI received an error from the network
Alarm Data =
44
MJD12
SPID Init Rec
Cabinet, Slot, Channel(Cx-Syy-czz)
The BRI has recovered from an error on the network
Alarm Data = Cabinet, Slot, Channel(Cx-Syy-czz)
45
MJD13
LPBK Error
Internal on demand loopback failed.
Alarm Data = Cabinet, Slot, Channel(Cx-Syy-czz)
46
MJD14
LPBK Recovery
Internal on demand loopback test passed.
Alarm Data = Cabinet, Slot, Channel(Cx-Syy-czz)
47
MJD15
BRI DL Unavail
A BRI data link is out of service.
Alarm Data = Cabinet, Slot, Channel(Cx-Syy-czz)
48
MJD16
BRI DL Recovery
A BRI data link is back in service.
Alarm Data = Cabinet, Slot, Channel(Cx-Syy-czz)
49
MJD17
RAM Error
An error has occurred in the TEPRI or BRI card RAM.
Alarm Data = Cabinet, Slot(Cx-Syy)
© SAMSUNG Electronics Co., Ltd.
2-401
CHAPTER 2. MMC Programming
No
50
Code
Alarm Name
Definition
MJD--
DTRK Error
ISDN or E1 card Fault
MJD18
E1 Restart
The E1 card has restarted
Alarm Data = Cabinet, Slot(Cx-Syy)
51
MJD19
PRI Restart
The PRI card has restarted
Alarm Data = Cabinet, Slot(Cx-Syy)
52
MJD20
BRI Restart
The BRI card has restarted
Alarm Data = Cabinet, Slot(Cx-Syy)
53
MJD21
PCM Loss
Loss of PCM coding on a digital facility.
Alarm Data = Cabinet, Slot(Cx-Syy)
54
MJD22
PCM Recovery
Loss of PCM coding on a digital facility.
Alarm Data = Cabinet, Slot(Cx-Syy)
55
MJE--
MGI Error
MJE01
MGI Restart
MGI card Fault
The MGI card has restarted
Alarm Data = Cabinet, Slot(Cx-Syy)
56
MJE02
MGI Stop
The MGI card has stoped
Alarm Data = Cabinet, Slot(Cx-Syy)
57
MJE03
MGI IP Duplicate
The MGI card IP address is duplicated
Alarm Data = Cabinet, Slot(Cx-Syy)
58
MJE04
MGI NTWK Error
The MGI card has blocked because the system detects
the card doesn’t response via network link.
External ping test.
Alarm Data = Cabinet, Slot(Cx-Syy)
59
MJE05
MGI NTWK Rec
The MGI card has restarted because the system detects
the card does response via network link.
External ping test.
Alarm Data = Cabinet, Slot(Cx-Syy)
60
MJE06
MGI DSP Error
The MGI card DSP has blocked because the system
detects the card DSP runs not correctly.
Alarm Data = Cabinet, Slot(Cx-Syy-Pzz)
61
MJE07
MGI DSP Run
The MGI card DSP has restarted because the system
detects the card DSP runs correctly.
Alarm Data = Cabinet, Slot(Cx-Syy-Pzz)
62
MJE08
WBS Disconnect
Indicates the WBS is disconnected.
Alarm Data = CWBS:xx or BWBS:xx
63
MJE09
WBS connect
Indicates the WBS is connected.
Alarm Data = CWBS:xx or BWBS:xx
2-402
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
No
64
Code
Alarm Name
Definition
MNF--
Minor Error
Minor Fault with Alarm Buffer saving
MNF01
Card Out
A circuit card mounted in a universal slot has been
removed from service or is not recognized by the system
Alarm Data = Cabinet, Slot(Cx-Syy)
65
MNF02
Card In
A circuit card mounted in a universal slot has been
returned to service.
Alarm Data = Cabinet, Slot(Cx-Syy)
66
MNF03
IPC Error
Inter processor communication error has occurred.
Alarm Data = Cabinet-Slot(Cx-Syy)
67
MNF04
Trunk Fault
Out of service trunk detected via loop detect. Internal
CODEC test.
Alarm Data = Cabinet, Slot, Port(Cx-Syy-Pzz)
68
MNF05
Trunk Recovery
Out of service trunk detected via loop detected as out of
service is now operational.
Alarm Data = Cabinet, Slot, Port(Cx-Syy-Pzz)
69
MNF06
Trunk
Out of service trunk detected via seizure of trunk.
Disconnect
External seizure test.
Alarm Data = Cabinet, Slot, Port(Cx-Syy-Pzz)
70
MNF07
Trunk Connect
Out of service trunk recovered via seizure of trunk
External seizure test.
Alarm Data = Cabinet, Slot, Port(Cx-Syy-Pzz)
71
MNF08
SIO TxQ Over
SIO Tx Queue full error has occurred in the MCP2.
Alarm Data = SIO number(SIO: x)
72
MNF09
SIO TxQ Under
SIO Tx Queue under error has occurred in the MCP2.
Alarm Data = SIO number(SIO: x)
73
MNF10
E1 Out Of Srv
E1 Digital line status has been changed to out of
service.
Alarm Data = Cabinet, Slot(Cx-Syy)
74
MNF11
E1 In Service
E1 Digital line has been restored to normal service.
Alarm Data = Cabinet, Slot(Cx-Syy)
75
MNF12
SIO Out
IO port has lost DTR
Alarm Data = SIO number(SIO: x)
76
MNF13
SIO In
IO port has regained DTR.
Alarm Data = SIO 1 through 6
77
MNF14
TODC Error
78
MNF15
TSW Over Alarm
Time of Day Clock in the MCP2 has erred.
The TSW has been requested to exceed the capacity of
available time slots. Maximum 192 per cabinet.
Alarm Data = Cabinet, Slot(Cx-Syy)
79
MNF16
PSU Alarm
Indicates there are over 56 ports in a cabinet with a
single PSU and more power is required.
Alarm Data = Cabinet, Slot(Cx-Syy)
© SAMSUNG Electronics Co., Ltd.
2-403
CHAPTER 2. MMC Programming
No
Code
Alarm Name
80
MNF17
PSU Alarm Rec
Definition
A second PSU has been recognized when added after
alarm condition of
Alarm Data = Cabinet, Slot(Cx-Syy)
81
MNF18
SLI Fault
An SLI card has been detected as out of service via an
internal CODEC test.
Alarm Data = Cabinet, Slot, Port(Cx-Syy-Pzz)
82
MNF19
SLI Recovery
An SLI card detected as out of service has been
detected as recovered and is in service via internal
CODEC test.
Alarm Data = Cabinet, Slot, Port(Cx-Syy-Pzz)
83
MNF20
PSUB Alarm
Indicates there are over 120 ports in a cabinet with two
PSU.
Alarm Data = Cabinet, Slot(Cx-Syy)
84
MNF21
DSS Alarm
System capacity of 64 button DSS modules has been
exceeded.
85
MNF26
SIO RxQ Over
SIO Tx Queue full error has occurred in the MCP2.
Alarm Data = SIO number(SIO: x)
86
MNF27
SIO RxQ Under
SIO Tx Queue under error has occurred in the MCP2.
Alarm Data = SIO number(SIO: x)
87
MNF28
LAN Printer Err
LAN printer error has occurred in the MCP2.
Alarm Data = Data Type(SMDR)
88
MNF29
LAN Printer Rec
LAN printer error has recovered in the MCP2.
Alarm Data = Data Type(SMDR)
89
90
MNG--
Minor Error
Minor Fault without Alarm Buffer saving
MNG01
Phone
Indicates the Phone is disconnected.
Disconnect
Alarm Data = Tel number or Cx-Syy-Pzz
Phone Connect
Indicates the Phone is connected.
MNG02
Alarm Data = Tel number or Cx-Syy-Pzz
91
MNG03
Off Hook Alarm
Indicates the Extension is Off Hook Alarm time over.
Alarm Data = Tel number or Cx-Syy-Pzz
92
MNG04
On Hook
Indicates the Off Hook Alarm Extension is on hook.
Alarm Data = Tel number or Cx-Syy-Pzz
93
MNG05
MGI Packet Loss
Indicates the MGI connection RTP packet loss is more
than 10 %.
Alarm Data = Tel number or Cx-Syy-Pzz
94
MNG06
MGI Packet Delay
Indicates the MGI connection RTP packet delay is more
than 500 ms.
Alarm Data = Tel number or Cx-Syy-Pzz
2-404
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
DEFAULT DATA
ALL OFF
ACTION
DISPLAY
1. Press Transfer button and enter 852.
Display shows:
01:MJA01 ACT:OFF
2. Enter desired Alarm Display number.(e.g., 64)
OR
Press the Volume buttons to select desired
option and press Right Soft button and to
advance the cursor.
64:MNF01 ACT:OFF
3. To select if the alarm is active press 1 for
YES and 0 for NO.
An entry will advance the cursor to return to
step 2.
OR
Press the Volume buttons to make selection
and press Right Soft button to save and
return step 2.
64:MNF01 ACT:ON
POR Restart
Card Out
Card Out
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 501
MMC 722
MMC 723
MMC 851
MMC 853
© SAMSUNG Electronics Co., Ltd.
SYSTEM TIMERS
STATION KEY ASSIGNMENT
SYSTEM WIDE KEY ASSIGNMENTS
SYSTEM ALARM REPORTING
MAINTENANCE BUSY
2-405
CHAPTER 2. MMC Programming
[853] MAINTENANCE BUSY
This MMC is used to place stations, trunks, and common resources equipment in a
maintenance busy condition. This can be used to isolate suspected intermittent problem
equipment. Stations placed in maintenance busy will behave like a station in DND when
called. The calling stations display(if equipped) will show ‘MADE BUSY’ when called.
Stations receiving DID or E & M type calls will receive a DND/ No more calls tone.
The station display will still function with station and date.
When the busy station is accessed, it will function like a locked all station. Trunks made
busy can not originate calls. Ring down type trunks will still ring the programmed
destination. Common resource equipment such as DSP’s, CID DSP’s and miscellaneous
equipment such as page ports, AA ports or voice mail card ports can also be placed in a
maintenance busy state.
MAINTENANCE BUSY OPTIONS
No
Option
Description
0
TRK
Trunks
1
STN
Stations
2
PAGE
Page Ports
3
AA
Auto Attendant card ports
4
DTMFR
DTMF Receiver(4/DSP)
5
CID
CID Receiver(14/DSP)
6
R2MFC
R2MFC Receiver(8/DSP)
7
CONF
GRP #01-24
8
MGI
MGI ports
DTMFR/CID/R2MFC DSP
Cases of DTMFR, CID or R2MFC DSP selection when DSP is not mounted
display will show NONE. If mounted display will show IDLE by default.
CONDITIONS
NONE
DEFAULT DATA
ALL IDLE
2-406
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
ACTION
DISPLAY
1. Press Transfer button and enter 853.
Display shows busy functions.
MAINTENANCE BUSY
2. Enter busy function type(0-8) via dial keypad.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
MAINTENANCE BUSY
3. Enter station number.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
MAINTENANCE BUSY
4. Press 1 to make busy or 0 to make idle.
OR
Press Volume button to make selection and
press Right Soft button to save and return step 3.
MAINTENANCE BUSY
TRK
STN
STN
STN
:NONE
:NONE
:201 IDLE
:201 BUSY
6. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
DEFAULT DATA
ALL IDLE
RELATED ITEMS
MMC 851
MMC 852
© SAMSUNG Electronics Co., Ltd.
ALARM REPORTING
ALARM KEY ASSIGNMENTS
2-407
CHAPTER 2. MMC Programming
[854] DIAGNOSTIC TIME
Provides a means to set the Diagnostic Time. The system diagnostics tests include memory
audits, internal loopback tests on digital trunks, DSP, AA DSP tests. Additional tests
include CODEC tests on analog trunk and station cards and tone tests. If the diagnostics
cannot complete the tests because of system traffic, the system will abort the test and retry
during the next programmed diagnostic time. It is recommended to assign the diagnostic
time during non-peak traffic periods.
PROGRAM BUTTONS
VOLUME
KEYPAD
SOFT BUTTONS
SPEAKER
Used to scroll through options
Used to enter selections
Move cursor left and right
Used to advance next MMC
ACTION
DISPLAY
1. Press Transfer button and enter 854.
Display shows:
DIAGNOSTIC TIME
2. Enter weekday number.
(0: Sun, 1: Mon, , 6: Sat)
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
DIAGNOSTIC TIME
3. Enter military time hour via the dial pad.
Cursor will advance to next entry.
DIAGNOSTIC TIME
4. Enter military time minutes via the dial pad.
Data saved and cursor will advance to step 2.
DIAGNOSTIC TIME
SUN: :
SUN:_ :
SUN:23:_
SUN:23:30
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 851
MMC 852
MMC 853
2-408
ALARM REPORTING
ALARM KEY ASSIGNMENTS
MAINTENANCE BUSY
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[855] SYSTEM OPTIONS
This MMC provides a means to review the common use hardware that is mounted in the
system. System Options show miscellaneous hardware and daughter boards. This enables
the technician to review the available hardware without having to dismantle or power down
the system to confirm if the hardware is mounted.
This is a READ ONLY MMC.
SYSTEM OPTIONS
OfficeServ 500-L System
Option
Description
MCP D-BD 1
Shows the Daughter Board #1 of MCP
MCP D-BD 2
Shows the Daughter Board #2 of MCP
MCP D-BD 3
Shows the Daughter Board #3 of MCP
MCP SW
Shows the DIP S/W status of MCP
C1 POWER-B
Shows the second power exist of Cabinet #1
SCP D-BD 1
Shows the Daughter Board #1 of SCP
SCP D-BD 2
Shows the Daughter Board #2 of SCP
SCP D-BD 3
Shows the Daughter Board #3 of SCP
LCP1 ONLINE
Shows the connection status of Cabinet #2 LCP
C2 POWER-B
Shows the second power exist of Cabinet #2
LCP1 D-BD 1
Shows the Daughter Board #1 of Cabinet #2 LCP
LCP1 D-BD 2
Shows the Daughter Board #2 of Cabinet #2 LCP
LCP1 D-BD 3
Shows the Daughter Board #3 of Cabinet #2 LCP
LCP2 ONLINE
Shows the connection status of Cabinet #3 LCP
C3 POWER-B
Shows the second power exist of Cabinet #3
LCP2 D-BD 1
Shows the Daughter Board #1 of Cabinet #3 LCP
LCP2 D-BD 2
Shows the Daughter Board #2 of Cabinet #3 LCP
LCP2 D-BD 3
Shows the Daughter Board #3 of Cabinet #3 LCP
CxSy VPM
Shows the VPM board status of Voice Mail Card.
CxSy SW
Shows the DIP S/W status of TEPRI card.
© SAMSUNG Electronics Co., Ltd.
2-409
CHAPTER 2. MMC Programming
OfficeServ-M System
Option
Description
MCP D-BD 1
Shows the Daughter Board #1 of MCP.
MCP D-BD 2
Shows the Daughter Board #2 of MCP.
MCP D-BD 3
Shows the Daughter Board #3 of MCP.
MCP SW
Shows the DIP S/W status of MCP.
C1 POWER-B
Shows the second power exist of Cabinet #1.
CxSy VPM
Shows the VPM board status of Voice Mail Card.
CxSy SW
Shows the DIP S/W status of TEPRI card.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 855.
Display shows:
SYSTEM OPTIONS
2. Press Volume button to view options.
SYSTEM OPTIONS
MCP D-BD 1 :ESM
MCP D-BD 2 :IPM
3. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-410
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[856] TECH PROGRAMMING LOGS
This MMC lists the date, time and entry location of the last eight times that technician
programming was accessed. This will allow a technician to determine if there was
unauthorized access to system programming and where this access occurred. The
information stored in this log will consist of 2 elements, the date and time it occurred at and
the access location.
There are 4 types of access location information as described below:
Type
NNNN
MODEM
Description
This would be the extension number of a phone that had accessed programming directly.
This would indicate that programming was accessed by PCMMC via the integrated
V90 modem attached to the IOM board of main cabinet.
LAN
This would indicate that programming was accessed by PCMMC via the LAN
connection on the MCP2 card of main cabinet.
SIOx
This would indicate that programming was accessed by PCMMC via one of the SIO
connections on the IOM board of the main cabinet where x is the number(2 or 3) of
the SIO port that was used.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 856.
Display shows:
(1) 11/22 11:03
2. Enter index number.(e.g., 3)
OR
Press Volume button to scroll.
(3) 11/22 12:30
201 :11/22 11:27
203 :11/22 13:30
3. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
PROGRAMMING
© SAMSUNG Electronics Co., Ltd.
2-411
CHAPTER 2. MMC Programming
[858] ASSIGN SYSTEM EMERGENCY ALARM
Assigns the alarm for alarm information to send Remote M & A PC via LAN.
ALARM CODE DEFINITION: See Alarm Code Definition on MMC 852
Alarm Code Definition
See Alarm Code Definition on MMC 852
CONDITIONS
NONE
DEFAULT DATA
All OFF
ACTION
DISPLAY
1. Press Transfer button and enter 858.
Display shows:
01:MJA01 ACT:OFF
2. Enter the alarm entry number.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
02:MJA02 ACT:OFF
3. Enter YES or NO(1, 0) for alarming.
OR
Press Volume button to make selection and
press Right Soft button to save and return step 2.
02:MJA02 ACT:ON
POR Restart
Soft Restart
Soft Restart
4. Press Transfer button and enter to exit.
OR
Press Speaker button advance to next MMC.
RELATED ITEMS
MMC 852
2-412
ALARM KEY ASSIGNMENTS
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[859] HARDWARE VERSION DISPLAY
This MMC is only used for system H/W EPLD version display. This is a READ ONLY
MMC.
OfficeServ 500-L System
No
Option
Description
00
MCP2 CARD
Shows the EPLD version of MCP2
01
MCP2 B1
Shows the Daughter Board and EPLD version #1 of MCP2
02
MCP2 B2
Shows the Daughter Board and EPLD version #2 of MCP2
03
MCP2 B3
Shows the Daughter Board and EPLD version #3 of MCP2
04
C1 M-BOARD
Shows the Mother Board EPLD version of Cabinet #1
05
C1 SCP2 CARD
Shows the EPLD version of SCP2 card
06
C1 SCP1
Shows the Daughter Board and EPLD version #1 of SCP
07
C1 SCP2
Shows the Daughter Board and EPLD version #2 of SCP
08
C1 SCP3
Shows the Daughter Board and EPLD version #3 of SCP
09
C2 M-BOARD
Shows the Mother Board EPLD version of Cabinet #2
10
C2 LCP2 CARD
Shows the EPLD version of Cabinet #2 LCP2 card
11
C2 LCP1
Shows the Daughter Board and EPLD version #1 of Cabinet #2 LCP
12
C2 LCP2
Shows the Daughter Board and EPLD version #2 of Cabinet #2 LCP
13
C2 LCP3
Shows the Daughter Board and EPLD version #3 of Cabinet #2 LCP
14
C3 M-BOARD
Shows the Mother Board EPLD version of Cabinet #3
15
C3 LCP2 CARD
Shows the EPLD version of Cabinet #3 LCP2 card
16
C3 LCP1
Shows the Daughter Board and EPLD version #1 of Cabinet #3 LCP
17
C3 LCP2
Shows the Daughter Board and EPLD version #2 of Cabinet #3 LCP
18
C3 LCP3
Shows the Daughter Board and EPLD version #3 of Cabinet #3 LCP
OfficeServ 500-M System
No
Option
Description
0
C1 M-BOARD
Shows the Mother Board EPLD version of Cabinet #1
1
MCP2 CARD
Shows the EPLD version of MCP2
2
MCP2 B1
Shows the Daughter Board and EPLD version #1 of MCP2
3
MCP2 B2
Shows the Daughter Board and EPLD version #2 of MCP2
4
MCP2 B3
Shows the Daughter Board and EPLD version #3 of MCP2
© SAMSUNG Electronics Co., Ltd.
2-413
CHAPTER 2. MMC Programming
ACTION
DISPLAY
1. Press Transfer button and enter 859.
Display shows:
H/W EPLD VERSION
2. Enter the option number.
OR
Press Volume button to scroll.
H/W EPLD VERSION
MCP CARD
:V01
MCP B3 :LAN :V05
3. Press Transfer button and enter to exit.
OR
Press Speaker button advance to next MMC.
RELATED ITEMS
NONE
2-414
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
[860] UCD STATUS SERVICE
This MMC is set to send the information of the UCD queue status or UCD Agent status to
the SIO port real time. To use this information, a special PC application is needed.
CONDITIONS
To use this information, a special PC application is needed.
DEFAULT DATA
UCD VIEW SERVICE: DISABLE
SENT AGENT STATE: NO
ACTION
DISPLAY
1. Press Transfer button and enter 860.
Display shows:
UCD VIEW SERVICE
2. Enter the number.
(0: UCD view service, 1: Send Agent state)
OR
Press Volume button to select and press
Right Soft button to move cursor.
SEND AGENT STATE
3. Enter YES or NO.(1, 0)
OR
Press Volume button to select and press
Right Soft button to store.
SEND AGENT STATE
DISABLE
YES
NO
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 804
© SAMSUNG Electronics Co., Ltd.
SYSTEM I/O PARAMETER
2-415
CHAPTER 2. MMC Programming
[861] SYSTEM OPTIONS
This MMC is set to system miscellaneous options.
No
Option
0
AUTO UPDATE TIME
Description
Sets enable(1) or disable(0) the system automatically time and
date update form ISDN call connection message. If sets enable,
when system receives ISDN call connection message, system
checks valid data of encapsulated time and date, and update
system time and date device.
1
SYSTEM SPPED BIN
Sets max 500(0) or max 950(1) the maximum number of system
speed dial bin. If sets 500 then same in previous system.
If sets 950, can assign system speed dial block is up to 950 bins
and speed dial bin numbers always 3 digits(000 to 999).
Even if station speed dial bin numbers are 3 digits(000 to 049).
2
IDLE WHEN
Decides the state of Large LCD Phone treated as idle or busy
ENBLOC
when the user of Large LCD Phone is dialling in ENBLOCK
mode.
3
2 LINE ENBLOCK
Decides the usage of ENBLOCK mode for 2 line LCD Phone with
navigation buttons
CONDITIONS
NONE
DEFAULT DATA
AUTO UPDATE TIME: DISABLE
SYSTEM SPEED BIN: MAX 500
IDLE WHEN ENBLOC: DISABLE
2 LINE ENBLOCK: DISABLE
ACTION
2-416
DISPLAY
1. Press Transfer button and enter 861.
Display shows:
AUTO UPDATE TIME
2. Enter the option number.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
AUTO UPDATE TIME
3. Enter 1 or 0 for option data select.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
AUTO UPDATE TIME
DISABLE
DISABLE
ENABLE
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
4. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
MMC 505
MMC 606
MMC 107
MMC 705
MMC 706
MMC 722
MMC 723
© SAMSUNG Electronics Co., Ltd.
ASSIGN TIME AND DATE
ASSIGN SPEED DIAL BLOCK
KEY EXTENDER
SYSTEM SPEED DIAL
SYSTEM SPEED DIAL BY NAME
STATION KEY PROGRAMMING
SYSTEM KEY PROGRAMMING
2-417
CHAPTER 2. MMC Programming
[890] INITIALIZE PORT
This program allows you to initialize items related to call process or DB for specific station
or Trunk line. This will return the port to default condition.
CONDITIONS
NONE
DEFAULT DATA
NONE
ACTION
DISPLAY
1. Press Transfer button and enter 890.
Display shows:
[201] CALL CLEAR
2. Enter the station or trunk line.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
[202] CALL CLEAR
3. Enter 0 to call clear only or 1 to initialize port.
OR
Press Volume button to make selection and
press Right Soft button to move cursor.
[202] DB INITIAL
4. Enter 1 for YES or 0 for NO.
OR
Press Volume button to make selection and
press Right Soft button to save and return step 2.
[202] DB INITIAL
ARE YOU SURE?NO
ARE YOU SURE?NO
ARE YOU SURE?NO
ARE YOU SURE?YES
5. Press Transfer button and enter to exit.
OR
Press Speaker button to advance next MMC.
RELATED ITEMS
NONE
2-418
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide
ANNEX A. ABBREVIATION
A
B
AAA
Authentication, Authorization and Accounting
AC
Alternating Current
ACD
Automatic Call Distribution
ALG
Application Level Gateway
AME
Answer Machine Emulation
AMI
Alternate Mark Inversion
AOM
Add On Module
AP
Access Point
BRI
Basic Rate Interface
CA
Call Agent
CCBS
Call Completion to Busy Subscriber
CCNR
Cell Completion on No Reply
CID
Caller Identification
CLI
Call Line Identification
COM
Communication
COS
Class Of Service
C
D
CPLD
Complex Programmable Logic Device
CRC
Cyclic Redundancy Code
CR Mode
Constant Resistance Mode
CSU
Communication Service Unit
CTI
Computer Telephony Integration
DASL
Digital Adapter Subscriber Loops
DID
Direct Inward Dialling
DECT
Digital Enhanced Cordless Telecommunications
DGP
Digital Phone
© SAMSUNG Electronics Co., Ltd.
A-1
ANNEX A. ABBREVIATION
DHCP
E
Dynamic Host Configuration Protocol
DLI
Digital Line Interface
DND
Do Not Disturb
DPIM
Door Phone Interface Module
DSP
Digital Signal Processor
DSU
Data Service Unit
DTMF
Dual Tone Multi Frequency
E/M
Ear and Mouth
EMI
Electro-Magnetic Interference
ESM
Expanded Switch Module
GARP
Generic Attribute Registration Protocol
GK
Gatekeeper
GVRP
GARP VLAN Registration Protocol
G
H
HDLC
High level Data Link Control
HLR
Home Location Register
HTML
Hypertext Markup Language
HTTP
Hypertext Transfer Protocol
ID
Identification
IDS
Intrusion Detection System
IGMP
Internet Group Management Protocol
IMAP
Internet Messaging Access Protocol
IN-SCP
Intelligent Network Service Control Point
IOM
Input/Output Module
IP
Internet Protocol
IPC
Inter Processor Communication
IPDC
Internet Protocol Device Control
I
A-2
IPM
Inter Processor Communications And Memory Module
IP-SCP
Internet Protocol Service Control Point
ISDN
Integrated Services Digital Network
ISUP
ISDN User Part
ITM
IP Telephony Module
ITP
IP Telephone
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
K
KDB
Keyset Daughter Board
LAN
Local Area Network
LCD
Liquid Crystal Display
LCP
Local Control Processor
LED
Light Emitting Diode
LIM
LAN Interface Module
MCP
Main Control Processor
MDF
Main Distribution Frame
MEGACO
Media Gateway Control
L
M
MFM
Multi Frequency Module
MG
Media Gateway
MGC
Media Gateway Controller
MGI
Media Gateway Interface
MGCP
Media Gateway Control Protocol
MISC
Miscellaneous Function Module
MMC
Man Machine Communication
MWSLI
Message Waiting Single Line Interface
N
NAT
Network Address Translation
NMS
Network Management System
OPX
Off Premises eXtension
PAT
Port Address Translation
O
P
PBA
Printed circuit Board Assembly
PCM
Pulse Code Modulation
PCMMC
PC based Man Machine Communication
PLL
Phase Locking Loop
POP3
Post Office Protocol version 3
PPP
Point to Point Protocol
© SAMSUNG Electronics Co., Ltd.
A-3
ANNEX A. ABBREVIATION
PPPoE
Point to Point Protocol over Ethernet
PRI
Primary Rate Interface
PRS
Polarity Reverse Detection
PSTN
Public Switched Telephone Network
PSU
Power Supply Unit
Q-SIG
Q-Signaling
QoS
Quality of Service
Q
R
RCM
R2/CID Module
RIP
Routing Information Protocol
RTCP
Real-time Transmission Control Protocol
RTP
Real-time Transmission Protocol
SCM
Switch and Conference Module
S
SCP
Signal Control Processor
SDP
Session Description Protocol
SG
Signaling Gateway
SGCP
Simple Gateway Control Protocol
SIGTRAN
Signaling Transport
SIO
Serial Input / Output
SIP
Session Initiation Protocol
SLI
Single Line Interface
SLT
Single Line Telephone
SMDR
Station Message Detail Recording
SMTP
Simple Mail Transfer Protocol
SoL
Server optimized Linux
STA
Spanning Tree Algorithm
STP
Signaling Transfer Point
SVMi
Samsung Voice Mail integrated
TAPI
Telephony Application Programming Interface
TCAP
Transmission Control Application Part
TCP
Transmission Control Protocol
TEPRI
T1E1PRI
TRK
Trunk
T
A-4
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500 Programming Guide/Ed.01
U
UA
User Agent
UAC
User Agent Client
UART
Universal Asynchronous Receiver and Transmitter
UAS
User Agent Server
UCD
Uniform Call Distribution
UDP
User Datagram Protocol
UPS
Uninterruptible Power System
USB
Universal Serial Bus
VDIAL
Voice Dial
VLAN
Virtual LAN
VoIP
Voice over Internet Protocol
VPM
Voice Processing Module
VPN
Virtual Private Network
WAN
Wide Area Network
WBS
Wireless Base Station
V
W
WIM
WAN Interface Module
WLI
Wireless LAN Interface
xDSL
x-Digital Subscriber Line
X
© SAMSUNG Electronics Co., Ltd.
A-5
ANNEX A. ABBREVIATION
This page is intentionally left blank.
A-6
© SAMSUNG Electronics Co., Ltd.
OfficeServ 500
Programming Guide
©2004 Samsung Electronics Co., Ltd.
All rights reserved.
Information in this guide is proprietary to SAMSUNG Electronics
Co., Ltd.
No information contained here may be copied, translated,
transcribed or duplicated by any form without the prior written
consent of SAMSUNG.
Information in this guide is subject to change without notice.