Motorola C6I
Digital Cordless Phone
For C601I, C602I, C603I and C604I
Warning
Charge the handset for 24 hours before use.
Welcome...
to your new Motorola C6I Digital Cordless Phone!
•
•
•
•
•
•
•
•
All handsets are fully cordless for locating anywhere within range.
50 Name and Number phonebook.
Speakerphone for hands-free conversation.
Caller ID shows you who’s calling and see details of the last 40 callers in a Calls list.*
Redial up to 10 of the last numbers called.
Register up to 4 handsets to a single base and register each handset with up to 4 different bases.
Make internal calls and transfer external calls between handsets.
Choose from 10 different ringtones for internal and external calls as well as numbers stored in the
phonebook.
*You must subscribe to your network provider’s Caller ID or Call Waiting service for these features to work. A subscription
fee may be payable.
Please note that this equipment is not designed for making emergency telephone calls when the power fails. Alternative
arrangements should be made for access to emergency services.
Need help?
If you have any problems setting up or using your C6I, please contact Customer Services on
659-1818.
Alternatively, you may find the answer in the ‘Help’ section at the back of this guide.
This User Guide provides you with all the information
you need to get the most from your phone.
Before you make your first call, you need to set up your phone.
Follow the simple instructions in ‘Getting Started’, on the next
few pages.
IMPORTANT
Only use the telephone line cord supplied.
•
•
Power Adaptor for the base
This equipment is not designed for making emergency
telephone calls when the power fails. Alternative
arrangements should be made for access to emergency
services.
•
Telephone line cord
Got everything?
• C6I handset
•
C6I base
2 x rechargeable Ni-MH battery cells
If you have purchased a C6I multiple pack you will
also have the following additional items:
•
C6I handset & charger
•
2 x rechargeable Ni-MH battery cells
•
Power adaptor for the charger
ECOMOTO: a convergence of efforts by marketing, design, research, engineering, and supply chain management
that leads to better products for everyone. A holistic view that focuses on both social and environmental
responsibility.
A passion and a shared point of view.
The right thing to do.
1) Meets and/or exceeds EMEA environmental regulatory requirements.
2) Eco friendly packaging with a minimum 20% post consumer recycled content.
3) Phone housing is built with a minimum of 25% post consumer recycle content plastic.
1. Getting started ................................................6
2. Getting to know your phone ..........................9
3.9.3 Delete an entry ......................................16
3.9.4 Delete the entire Redial list ....................16
3.10Paging/Find handset ..........................................16
3. Using the phone............................................13
4. Phonebook setting ....................................... 17
3.1 Switch the handset on / off ................................ 13
3.2 Calls................................................................... 13
3.2.1 Making calls .......................................... 13
3.2.2 Preparatory dialing ................................ 13
3.2.3 Answering calls ..................................... 13
3.2.4 End calls ............................................... 13
3.3 Hands-free mode............................................... 13
3.3.1 Make a hands-free call .......................... 13
3.3.2 Answer a call hands-free ...................... 14
3.3.3 Switch to hands-free during a call ......... 14
3.4 Adjust the earpiece and hands-free receive
volume ............................................................... 14
3.5 Secrecy mode.................................................... 14
3.6 Insert a Pause ................................................... 14
3.7 Intercom function ............................................... 14
3.7.1 Make an internal call ............................. 14
3.7.2 Receive an internal call ......................... 15
3.7.3 Transfer a call ....................................... 15
3.8 3-way conference call........................................ 15
3.9 Redial ................................................................ 15
3.9.1 View or dial an entry ............................. 15
3.9.2 Copy a Redial list number to the
phonebook ............................................. 16
4
4.1
4.2
4.3
4.4
Store a name and number..................................17
View or dial an entry ...........................................17
Edit a name and number ....................................18
Delete an entry ...................................................18
5. Handset settings .......................................... 19
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
Handset ringer volume .......................................19
Handset ringer melody .......................................19
Auto answer .......................................................19
Handset name ....................................................19
Language ...........................................................20
Key beep ............................................................20
Battery low warning beep ...................................20
Out of range warning beep .................................20
Keypad lock/unlock ............................................21
6. Base settings ................................................ 21
6.1
6.2
6.3
6.4
6.5
6.6
Base ringer volume ............................................21
Base ringer melody ............................................21
Change base PIN code ......................................22
Tone/Pulse setting..............................................22
Flash setting .......................................................22
Restore default settings......................................22
6.7 Emergency default ............................................. 23
6.8 Area code setting ............................................... 23
6.9 Default settings .................................................. 23
7. Clock & alarm ............................................... 24
7.1
7.2
7.3
7.4
Set the date........................................................ 24
Set the time ........................................................ 24
Set alarm............................................................ 24
Switch off alarm ring........................................... 24
8. Caller Display and the Calls list.................. 25
8.1 Caller Display ..................................................... 25
8.2 Calls list .............................................................. 25
8.2.1 View the Calls list .................................. 26
8.2.2 Dial a number in the Calls list ................ 26
8.2.3 Add "0" during call back ......................... 26
8.2.4 Copy a Calls list number to the
phonebook.............................................. 26
8.2.5 Delete an entry ...................................... 27
8.2.6 Delete the entire Calls list ...................... 27
9. Using additional handsets .......................... 27
9.1 Registering an additional handset ...................... 27
9.2 Select a base ..................................................... 28
9.2.1 De-register a handset ............................ 28
10. Help ............................................................... 29
11. General information..................................... 30
5
1. Getting started
WARNING
Do not place your C6I in the bathroom or other humid areas.
Location
You need to place your C6I base within 2 metres of the
mains power and telephone wall sockets so that the cables
will reach. The socket-outlet shall be installed near the
equipment and shall be easily accessible.
Make sure that it is at least 1 metre away from other
electrical appliances to avoid interference. Your C6I works
by sending radio signals between the handset and base. The
strength of the signal depends on where you place the base.
Placing it as high as possible ensures the best signal.
HANDSET RANGE
The unit has a range of up to 300 metres outdoors when there
is a clear line of sight between the base and handset. Any
obstruction between the base and handset will reduce the
range significantly. With the base indoors and the handset
either indoors or outdoors, the range will normally be up to 50
metres. Thick concrete walls can severely affect the range.
SIGNAL STRENGTH
The
icon on your handset indicates that you are within
range of the base. When out of range of the base, the
icon flashes. If you are on a call, you will hear a warning
beep.
6
The line will hang up if the handset moves out of range of the
base. Move closer to the base. The handset will
automatically reconnect to the base.
Setting up
IMPORTANT
The base station must be plugged into the mains power at all
times. Do not connect the telephone line cord into the wall
socket until the handset is fully charged. Use only the power
adaptor and telephone line cord supplied with the product.
WHICH POWER ADAPTOR?
The power adaptor with a clear connecter is for the base unit
and the power adaptor with a red colour connecter is for the
charger unit (for multi-pack only).
Connecting the base
1. Plug the telephone line cord into the socket marked
on the underside of the base.
Getting started
2. Plug the power adaptor with RED connecter into the
on the underside of the base and
socket marked
plug the other end into the mains power wall socket.
Switch on the mains power.
Installing and charging the handset
1. Remove the battery cover from the back of the handset
and insert the 2 x AAA NiMH rechargeble batteries
supplied. Please note the ’+’ and ’-’ markings inside the
battery compartment and insert in the correct direction.
2. Slide the battery cover back into place.
3. If you are charging the batteries for the first time, place
the handset on the base to charge for at least 24 hours
continuously.
4. When the handset is fully charged,
icon will
appear steadily on the display. Plug the other end of the
telephone line cord (make sure that one end is already
plugged into the base) into the telephone wall socket.
Connecting the handset and charger
(for multi-pack only)
If you have purchased a multiple pack, you will need to carry
out this process for all the handsets and chargers.
1. Plug the power adaptor with red connecter into the
socket marked
on the underside of the charger
and plug the other end into the mains power wall socket.
Getting started
2. Remove the battery cover from the back of the handset
and insert the 2 x AAA NiMH rechargeble batteries
supplied. Please note the ’+’ and ’-’ markings inside the
battery compartment and insert in the correct direction.
3. Slide the battery cover back into place.
4. If you are charging the batteries for the first time, place
the handset on the charger to charge for at least 24
hours continuously.
5. When the handset is fully charged,
icon will
appear steadily on the display.
The display will show the time and handset number
(e.g. 2) to indicate that it is registered to the base.
IMPORTANT
Warning! Use only the approved rechargeable Ni-MH battery
cells (2 x AAA Ni-MH 550mA rechargeable batteries)
supplied with your C6I.
7
BATTERY LOW WARNING
If
icon flashes on the display and you hear a warning
beep every minute during a call, you will need to recharge
the handset before you can use it again.
When charging,
icon will scroll on the display.
BATTERY PERFORMANCE
In ideal conditions, fully charged batteries should give up to
10 hours talk time and up to 150 hours standby time on a
single charge*.
Note that new batteries do not reach their full capacity until
they have been put to normal use for several days.
To keep your batteries in the best condition, leave the
handset off the base for a few hours at a time.
Running the batteries right down at least once a week will
help them last as long as possible.
Set the date manually
1. Press m, scroll d to DATE-TIME and press m.
The display shows DATE SET.
2. Press m to select.
3. Enter the date (e.g. 12/08/11 for 12th of August, 2011)
and press m to confirm.
Set the time manually
1. Press m, scroll d to DATE-TIME and press m.
2. Scroll d to CLOCK SET and press m.
3. Enter the time in 24 hour format (e.g. 18--30 for 6.30pm)
and press m to confirm.
Your phone is now ready for use.
The charge capacity of rechargeable batteries will reduce
with time as they wear out, giving the handset less talk/
standby time. Eventually they will need to be replaced.
After charging your handset for the first time, subsequent
charging time is about 6–8 hours a day. Batteries and
handset may become warm during charging. This is normal.
* All talk and standby times are approximate and depend on
features selected and usage pattern.
8
Getting started
2. Getting to know your phone
Overview of your handset
A
B
C
Secrecy / Clear / Back
D
Menu / OK
E
Redial / Up
F
Calls list / Down
G
Getting to know your phone
Earpiece
Display
See page 10 for an overview of the display icons.
During a call, press to switch Secrecy on/off, page 14.
In menu mode, press to return to previous menu or press
and hold to return to standby.
In editing mode, press to delete characters and digits.
When viewing the redial/calls list, press to delete the
displayed entry or press and hold to delete all entries.
Press to open the Menu, page 11.
Press to select menu options and to confirm a displayed option.
In standby mode, press to open the redial list, page 15.
During a call, press to increase earpiece volume, page 14.
When the phone is ringing, press to increase the handset
ringer volume, page 14.
Press to scroll through the menu options, redial list, calls list
and phonebook entries.
In standby mode, press to open the calls list, page 25.
During a call, press to decrease earpiece volume, page 14.
When the phone is ringing, press to decrease the handset
ringer volume, page 14.
Press to scroll through the menu options, redial list, calls list
and phonebook entries.
Phonebook / Exit
In standby mode, press to open the phonebook menu, page 17.
When viewing the redial/calls list or when editing, press to
exit and return to standby.
9
H
Hands-free
During a call, press to switch hands-free on and off, page 13.
Display icons
Talk / End call
Flashes to indicate an incoming external call
J
# / Keypad lock
External call in progress
Press and hold to lock the keypad, page 21.
To unlock, press any and follow the on screen instructions.
Flashes to indicate an incoming internal call
K
Intercom
Internal call in progress
L
Flash / Power on/off
3-way call in progress or transfer an external call to
another C6 handset registered to the base
I
Press to make, receive and end calls, page 13.
Used to make internal calls and transfer calls to other C6I
handsets registered to the base, page 14.
Use with switchboard/PABX services and some network
services.
Press and hold to switch the handset on/off, page 13.
Handset LCD Display
Battery
status
Scrolls
when
charging
Flashes to indicate new voicemail messages received
Off when you have no voicemail messages
Indicates signal strength
Flashes when handset is not registered to the base
or if you go out of range
Hands-free mode is ON
Menu is opened
Phonebook is opened
Flashes to indicate new calls list entries received*
Time or Handset name
In standby mode, press and hold 0 to switch
handset idle screen between handset name or time.
10
Answered call (when viewing the Calls list)*
Unanswered call (when viewing the Calls list)*
Getting to know your phone
Keypad is locked
A
Displayed number is longer than 12 digits
The approximate power levels of your battery are indicated
as follows:
Paging
In standby mode, press to ring the handset(s).
Press and hold to enter registration mode when registering
handsets.
Navigating the menus
Battery is fully charged
Your phone has an easy to use menu system.
Battery is partially charged
Each menu has a list of options, which you can see on the
menu map on the following pages.
Battery is running low
Flashes when battery is almost fully discharged
* For this feature to work, you must subscribe to Caller
Display Service from your network operator. A subscription
fee may be payable.
When the handset is switched on and in standby:
1. Press m to open the main menu.
2. Then use u or d buttons to scroll through the available
options.
3. Press m to select an option.
Overview of the base
4. To return to the previous menu level, press n.
5. To exit the menu and return to standby, press and hold
n.
A
Getting to know your phone
Note
If no buttons are pressed for 30 seconds, the handset
returns to standby automatically.
11
Menu map
PHONEBOOK
SETUP
HANDSET
DATE - TIME
REGISTER
ADD ENTRY
MODIFY ENTRY
DELETE ENTRY
BASE VOLUME
BASE MELODY
DEL HANDSET
PIN CODE
DIAL MODE
FLASH
DEFAULT
AREA CODE
BEEP
INT RING VOL
EXT RING VOL
INT MELODY
EXT MELODY
AUTO ANSWER
NAME
LANGUAGE
KEYLOCK
DATE SET
CLOCK SET
ALARM SET
SELECT BASE
REG BASE
12
Getting to know your phone
3. Using the phone
Note
Your handset will automatically time the duration of all
external calls. The call timer will display after the first 15
seconds of your call. When the call ends, the total duration
of your talk time is shown for 5 seconds.
3.1
Switch the handset on / off
Press < to switch the handset on or off.
3.2
Calls
3.2.1
Making calls
1. Pick up the handset and press the <.
2. When finished the conversation, , press the < to hang
up.
NOTE
If you prefer to press < when you lift up the handset to
answer a call, you will need to switch Auto answer off.
3.2.4
End calls
When you are on the call and you want to disconnect the call,
press < to end the call and return to standby mode.
3.3
Hands-free mode
Hands-free lets you talk to your caller without holding the
handset. It also enables other people in the room to listen to
the conversation over the loudspeaker.
2. When you hear a dial tone, dial the number you want to
call.
3.3.1
3.2.2
2. Press S to switch the call between the earpiece and
the loudspeaker.
3. When finished the conversation, press the < to hang
up.
Preparatory dialing
1. Dial the number first. If you make a mistake, press n
to delete the last digit.
2. Press < or S to dial.
3.2.3
Answering calls
1. When the phone rings ,pick up the handset and press
the <.
Using the phone
Make a hands-free call
1. Dial the number then press S.
icon is displayed and you will hear the call over the
handset loudspeaker.
3. Press < to end the call.
Note
During a hands-free call, press d then u or d to adjust the
volume.
13
3.3.2
Answer a call hands-free
3.5
Switch to hands-free during a call
You can mute your handset so that you can talk to someone
nearby without your caller hearing.
When the phone rings, press S to answer the call.
3.3.3
1. During a call, press S to put the call on the
loudspeaker.
Secrecy mode
1. During a call, press n. The display shows MUTED and
your caller cannot hear you.
2. To switch hands-free off and return the call to the
earpiece, press S again.
2. Press n again to resume your call.
4. Press S to alternate between speakerphone and
normal handset use.
With some switchboards, after dialling the access code you
may have to wait for a moment while the switchboard picks
up an outside line so you will need to enter a pause in the
dialing sequence.
3. Press < to end the call.
Note
For best speaker phone, it is recommended to keep the
handset away from your mouth by 5~6 inches during
conversation in speaker mode.
3.4
Adjust the earpiece and hands-free
receive volume
There are 5 Levels (VOLUME 1 to VOLUME 5).
During a call, press d first then press u to increase and d
to decrease the earpiece volume or speaker volume.
3.6
Insert a Pause
Press and hold # to insert a pause (P) before entering the
telephone number.
You may also need to enter a pause when storing
international numbers or charge card numbers.
3.7
Intercom function
3.7.1
Make an internal call
If you have more than one handset registered to the base,
you can make internal calls between two handsets.
icon is displayed to indicate an internal call.
1. Press I followed by the number (1-4) of the handset
you want to call.
14
Using the phone
3.7.2
Receive an internal call
1. When you receive an internal call,
icon flashes and
the handset number that is calling you is displayed.
2. Press < to answer the call.
3.7.3
Transfer a call
You can transfer an external call to another handset
registered to the base.
During an external call:
1. Press I followed by the handset number (1-4) that
you want to transfer to.
During a call with an external caller:
1. Press I followed by the handset number (1-4) that
you want to establish a conference call.
2. When the other handset answers, press # to connect
all three callers to begin the conference call.
icon is displayed.
3. If there is no answer from the other handset, press I
to return to your external caller.
4. Press < to end the call.
2. When the other handset answers, press < to complete
the transfer.
3.9
Note
If there is no answer from the other handset and you wish to
return to your external caller, press I.
Your external call resumes automatically after 1 minute if
there is no answer.
3.9.1
3.8
3-way conference call
You can hold a 3-way conference call between 2 internal
callers and 1 external caller.
Using the phone
Redial
The last 10 entries dialed are stored in the redial list.
View or dial an entry
1. Press u to open the Redial list.
2. Scroll u or d to the entry you want.
3. Press < to dial the displayed entry or press B to
return to standby.
Note
If the caller’s number exactly matches an entry stored in the
phonebook, the name is displayed.
15
3.9.2
Copy a Redial list number to the phonebook
1. Press u to open the Redial list.
2. Scroll u or d to the entry you want.
3. Press m. The display shows ADD ?.
4. Press m again. The display shows NAME ?.
5. Enter the name and press m. The number is
displayed.
6. Edit the number if necessary, then press m.
3.10
Paging/Find handset
You can alert a handset user that they are wanted or locate
a missing handset. Paging calls cannot be answered by a
handset.
1. Press p on the base. All handsets registered to the
base will ring.
2. To stop the ringing, press p on the base again or press
any button on the handset.
7. Press u or d to select the ringer melody you want and
press m. The number is stored.
NOTE
See “ENTERING NAMES” and “WRITING TIPS”.
3.9.3
Delete an entry
1. Press u to open the Redial list.
2. Scroll u or d to the entry you want and press n. The
display shows DELETE ?.
3. Press m to confirm or B to cancel.
3.9.4
Delete the entire Redial list
1. Press u to open the Redial list.
2. Press and hold n. The display shows DELETE ALL ?.
3. Press m to confirm or B to cancel.
16
Using the phone
4. Phonebook setting
You can store up to 50 names and numbers in the
phonebook. Names can be up to 16 characters long and
number up to 24 digits. You can also select different ringer
melodies for the phonebook entries.
4.1
Store a name and number
If you have subscribed to Caller Display Service and wish to
display the name of your caller instead of the number, save
the full telephone number including the area code to your
phonebook.
7. Enter the next name and number entry that you wish to
store in your phonebook or press B to return to
standby.
ENTERING NAMES
Use the keypad letters to enter names, e.g. to store TOM:
Press 8 once to enter T.
Press 6 three times to enter O.
Press 6 once to enter M.
WRITING TIPS
Press n to delete the last character or digit.
Press u or d to move between characters/digits.
You can store multiple entries with the same number.
However, to prevent unnecessary duplicated entries, you
can only store the same name once.
Press 1 to insert a space.
2. Press m to select. The display shows ADD ENTRY.
4.2
1. Press m. The display shows PHONEBOOK.
3. Press m to select. The display shows NAME ?.
4. Enter the name and press m. The display shows
NUMBER ?.
5. Enter the number and press m. The display shows
MELODY 1.
6. Press u or d to select the ringer melody you want and
press m. The display shows ADD ENTRY.
Phonebook setting
Use 1 twice to insert a dash.
View or dial an entry
1. Press B.
icon is displayed.
2. Scroll u or d to the entry you want.
OR
1. Enter the first letter of the name to search alphabetically.
The first name that starts with this letter or the nearest
letter in the alphabet will be displayed.
17
2. Scroll u or d to the entry you want. Press < to dial or
B to return to standby.
4.4
Note
When the name is displayed, you can switch between the
name and number by pressing m.
3. Scroll d to DELETE ENTRY and press m.
4.3
Edit a name and number
1. Press m. The display shows B.
2. Press m to select.
3. Scroll d to MODIFY ENTRY and press m.
Delete an entry
1. Press m. The display shows PHONEBOOK.
2. Press m to select.
4. Scroll u or d to the entry you want to delete, or search
alphabetically and press m.
The display shows CONFIRM ?.
5. Press m to confirm or B to cancel.
4. Scroll u or d to the entry you want to edit, or search
alphabetically and press m. The existing name is
displayed.
5. Press u to delete the name if required, then enter the
new name and press m. The existing number is
displayed.
6. Press u to delete the number if required, then enter the
new number and press m.
7. Scroll u or d to select a new ringer melody and press
m. The display shows ADD ENTRY.
8. Enter the next name and number entry you wish to store
in your phonebook or press B to return to standby.
18
Phonebook setting
5. Handset settings
5.1
Handset ringer volume
You can adjust the ring volume and set different volume
levels for your internal and external calls. Choose from 5
volume levels or Off.
1. Press m, scroll d to HANDSET and press m.
2. Press u or d to select INT RING VOL or EXT RING VOL and
press m.
3. Press u or d to select the ringer melody (1 - 10).
4. Press m to confirm n to return to the previous
menu.
Note
Calls from the numbers that you have stored in the
phonebook will ring using the ringer melody you have set
when you store the entry.
5.3
Auto answer
3. Press u or d to select the volume (1 - 5 or OFF) .
Your phone is set to answer calls by lifting the handset off the
base or charger. You can switch this feature off so that calls
can only be answered by pressing <.
Note
When the phone is ringing, you can adjust the ringer volume
by pressing u or d.
2. Scroll d to AUTO ANSWER and press m.
4. Press m to confirm or n to return to the previous
menu.
5.2
Handset ringer melody
You can set different ringer melodies for your internal and
external calls. Choose from 10 different ringer melodies.
You will hear a sample ring as you scroll to each ring melody.
1. Press m, scroll d to HANDSET and press m.
2. Press u or d to select INT MELODY or EXT MELODY and
press m.
Handset settings
1. Press m, scroll d to HANDSET and press m.
3. Press u or d to select ON or OFF and press m to
confirm.
5.4
Handset name
If you are using more than one handset with your base, you
can set a personalized name for each handset to easily
distinguish between them. A name can be up to 10
characters long.
1. Press m, scroll d to HANDSET and press m.
2. Scroll d to NAME and press m.
19
3. Enter the new handset name and press m to confirm.
5.7
Note
The handset name will only be displayed for approximately
30 seconds when no button is pressed. If you make a
mistake, press n to delete the last character or digit. See
“ENTERING NAMES” and “WRITING TIPS”.
When the battery is almost fully discharged, you will hear a
warning beep every minute during a call. You can switch
these beeps on or off.
5.5
Language
Battery low warning beep
1. Press m, scroll d to HANDSET and press m.
The display shows BEEP.
2. Press m to select.
1. Press m, scroll d to HANDSET and press m.
3. Scroll d to LOW BATTERY and press m.
3. Press u or d to select your preferred language and
press m to confirm.
5.8
2. Scroll d to LANGUAGE and press m.
5.6
Key beep
When you press a button on the keypad, you will hear a
beep. You can switch these beeps on or off.
1. Press m, scroll d to HANDSET and press m.
The display shows BEEP.
2. Press m to select. The display shows KEYTONE.
3. Press m to select.
4. Press u or d to select ON or OFF and press m to
confirm.
20
4. Press u or d to select ON or OFF and press m to
confirm.
Out of range warning beep
If the handset goes out of range, you will hear warning beeps
during a call. You can switch these beeps on or off.
1. Press m, scroll d to HANDSET and press m.
The display shows BEEP.
2. Press m to select.
3. Scroll d to OUT RANGE and press m.
4. Press u or d to select ON or OFF and press m to
confirm.
Handset settings
5.9
Keypad lock/unlock
You can use the menu to lock the keypad.
1. Press m, scroll d to HANDSET and press m.
2. Scroll d to KEYLOCK ? and press m to confirm.
icon is displayed.
OR
1. Press and hold #.
icon is displayed.
2. To unlock the keypad, press any key on your handset.
The display shows PRESS # .
6. Base settings
6.1
Base ringer volume
Choose from 5 volume levels or Off.
1. Press m, scroll d to SETUP and press m. The display
shows BASE VOLUME.
2. Press m.
3. Press u or d to select the volume (1 - 5 or OFF).
4. Press m to confirm or n to return to the previous
menu.
3. Press # within 3 seconds.
6.2
Note:
To unlock the keypad, press any button on the keypad, then
press # within 3 seconds.
Choose from 5 different base ringer melodies. You will hear
a sample ring as you scroll to each ringer melody.
When the keypad is locked, you can still answer incoming
calls and operate the handset as normal.
When the call ends, the keypad lock comes on again.
Base settings
Base ringer melody
1. Press m, scroll d to SETUP and press m.
2. Scroll d to BASE MELODY and press m.
3. Press u or d to select the ringer melody (1 - 5).
4. Press m to confirm or n to return to the previous
menu.
21
6.3
Change base PIN code
Some functions are protected by a 4 digit PIN code which
must be entered if you want to change the settings. The
default PIN is 0000. You can change this to your own
preferred number.
6.5
Flash setting
Depending on your country and network operator, your
phone has the flash time set as 600 ms (FLASH 2). It is
unlikely that you need to change this setting unless advised
to do so.
When you enter a PIN, the digits are shown as **** .
1. Press m, scroll d to SETUP and press m.
2. Scroll d to PIN CODE and press m.
3. Press u or d to select FLASH 1 (short flash time) or
FLASH 2 (long flash time) and press m to confirm.
1. Press m, scroll d to SETUP and press m.
3. Enter the 4 digit PIN code (default = 0000) and press
m.
4. Re-enter the new PIN again and press m to confirm.
IMPORTANT
If you change the PIN code, please keep a record of the new
number.
6.4
Tone/Pulse setting
Your phone is set to tone dialing. You should only need to
change this if connected to an older type of switchboard/PBX
which requires pulse dialing.
1. Press m, scroll d to SETUP and press m.
2. Scroll d to DIAL MODE and press m.
3. Press u or d to select TONE DIAL or PULSE DIAL and press
m to confirm.
22
2. Scroll d to FLASH and press m.
Note
You may need to use the flash function if you are connected
to a PBX switch.
Contact your PABX supplier for further information.
6.6
Restore default settings
You can restore your phone to its default (original) settings.
All the handsets that are registered to the base will be
retained.
WARNING
Resetting your phone to its default settings will delete all
entries in the Phonebook and Calls list. All handset and base
settings will also be reset.
1. Press m, scroll d to SETUP and press m.
2. Scroll d to DEFAULT and press m.
Base settings
3. Enter the 4 digit PIN code (default = 0000) and press
m. The display shows CONFIRM?.
4. Press m to confirm or B to return to the previous
menu. Your phone will restart automatically.
6.7
Emergency default
If you have lost your PIN code, you can still restore your
phone to its default settings.
1. Remove the batteries from the handset.
2. Press and hold * while replacing the batteries. The
display shows DEFAULT.
3. Press m to confirm. Your phone will restart
automatically.
6.8
Area code setting
1. Press m, scroll d to SET UP and press m.
2. Scroll d to AREA CODE and press m.
3. Enter the desired AREA CODE (up to 6 digits) using
keypad and press m to confirm.
Note
The area code is the STD code of the city (Area) where the
cordless is connected e.g. for Delhi: 11 please set "11..." in
the Area Code setting for Delhi.
Base settings
The handset will filter the local area code (set by user) while
receiving or calling back the local number.
6.9
Default settings
Low battery beeps
Out of range warning beeps
Key beep
Auto answer
Internal melody
Internal volume
External melody
External volume
Base volume
Base melody
Ear volume
Phonebook
Calls list
Redial list
PIN Code
Dial Mode
Flash
Area Code
Keypad lock
ON
ON
ON
ON
1
3
3
3
3
2
3
Empty
Empty
Empty
0000
Tone
Flash 2 (600 ms)
Blank
OFF
23
7. Clock & alarm
If you have subscribed to Caller Display service, the date
and time will be set on all your handsets whenever a call is
received. You can also manually set the date and time on the
individual handsets.
7.1
Set the date
1. Press m, scroll d to DATE-TIME and press m.
The display shows DATE SET.
2. Press m to select.
3. Press u or d to select ON or OFF and press m to
confirm.
4. If you select ON, enter the time in 24 hour format (e.g.
07--30 for 7:30am) and press m to confirm.
7.4
Switch off alarm ring
When the alarm sounds, press any button to switch it off.
Note
If you are using the handset to make a call when the alarm
ring is due, you will hear a beep in the earpiece.
3. Enter the date (e.g. 12--08 for 12th of August) and press
m to confirm.
7.2
Set the time
1. Press m, scroll d to DATE-TIME and press m.
2. Scroll d to CLOCK SET and press m.
3. Enter the time in 24 hour format (e.g. 18--30 for 6:30pm)
and press m to confirm.
7.3
Set alarm
Each handset can have a different alarm setting.
1. Press m, scroll d to DATE-TIME and press m.
2. Scroll d to ALARM SET and press m.
24
Clock & alarm
8. Caller Display and the Calls list
IMPORTANT
To use Caller Display, you must first subscribe to the service
from your network provider. A subscription fee may be
payable.
To ensure that the caller's name is displayed, make sure you
have stored the full telephone number, including the area
code in the phone book.
If the callers number is stored in the phone book, the name
assigned to it will be displayed.
If the call is a withheld call, WITHHELD will be displayed.
If the number is unavailable, UNAVAILABLE will be displayed.
If the call is from an international number, INT’L will be
displayed.
If the call is from the operator, OPERATOR will be displayed.
If the call is from a payphone, PAYPHONE will be displayed.
If the call is from a ring back request, RINGBACK will be
displayed.
Caller Display and the Calls list
8.1
Caller Display
If you have subscribed to a Caller Display Service, you will
be able to see your caller’s number on your handset
(provided it is not withheld) prior to answering the call. The
display can show the first 12 digits or characters of the phone
numbers and names. If your caller’s name and number are
stored in the phonebook and a name/number match is
found, you will see the caller’s name on the display instead.
8.2
Calls list
The Calls list stores details of your last 40 received calls,
including the phone number and date and time of the call.
The Calls list also alerts you when you have unanswered
calls. The caller’s details are stored in the Calls list whether
or not you have answered the call.
The list is shared by all handsets registered to the base.
When the list is full, and a new call is received, the oldest
entry will be deleted automatically.
When a new call is received in the Call list,
icon will flash
on the display in standby mode to alert you. When you have
viewed the new call,
icon disappears but
icon will
remain.
25
8.2.1
View the Calls list
1. Press d to open the Calls list. If there are no calls in the
list, the display shows EMPTY.
2. Press u or d to scroll through the list.
• If the call was answered,
icon is displayed as you
scroll to the entry.
• If the call was unanswered,
icon is displayed as you
scroll to the entry.
• When you reach the end of the list, the handset will
beep.
• If the caller’s number exactly matches an entry stored
in the phonebook, the display will alternate between
the name and the number.
3. Press m to see the caller’s number.
4. If the telephone number is longer than 12 digits,
icon is displayed. Press m to see the remaining digits.
5. Press m again to see the time and date of the call.
6. Press m again to access the option to store the entry
in your phonebook.
8.2.2
Dial a number in the Calls list
1. Press d to open the Calls list.
2. Scroll u or d to the entry you want.
8.2.3
Add "0" during call back
1. Make sure the phone is off (Not in talk mode).
2. Press d to access the call list.
3. Press the u or d to select the desired Number which
you want dial out with 0 in the beginning of the CID
number.
4. Press 0 after bringing the desired CID number on
the display that you want to call back.
5. Press < or S on the handset to dial the number.
6. When conversation finished, press the < to hang up.
Note
0 can be added only when the desired number is not less
than 11 digits.
8.2.4
Copy a Calls list number to the phonebook
1. Press d to open the Calls list.
2. Scroll u or d to the entry you want.
3. Press m repeatedly until the display shows ADD ?.
4. Press m again. The display shows NAME ?.
5. Enter the name and press m. The number is
displayed.
6. Edit the number if necessary, then press m.
3. Press < to dial the displayed entry.
26
Caller Display and the Calls list
7. Press u or d to select the ringer melody you want and
press m. The number is stored.
NOTE
See “ENTERING NAMES” and “WRITING TIPS”.
8.2.5
Delete an entry
1. Press d to open the Calls list.
2. Scroll u or d to the entry you want and press n.
The display shows DELETE?.
3. Press m to confirm or B to cancel.
8.2.6
Delete the entire Calls list
1. Press d to open the Calls list.
2. Press and hold n. The display shows DELETE ALL?.
3. Press m to confirm or B to cancel.
9. Using additional handsets
You can register up to four handsets to your base to extend
your phone system without having to install extension
sockets for each new phone.
Each handset can be registered with up to four bases. You
can then select the base you prefer to use.
If you have purchased a multiple pack, all additional
handsets come preregistered to the base.
If you have purchased an additional handset separately, you
must register it to your base before it can be used.
9.1
Registering an additional handset
Note
Handset batteries must be fully charged before you start to
register. Hold your handset close to the base during the
registration process. Handsets that were supplied with your
base are already pre-registered.
On the base:
Press and hold p for 3 seconds until you hear two beeps.
The base will remain in registration mode for 90 seconds.
On the handset:
1. Press m, scroll d to REGISTER and press m.
2. Scroll d to REG BASE and press m.
Using additional handsets
27
3. Enter the base number (1 - 4). The base numbers that
are already in use flashes. The display shows
SEARCHING....
4. When the handset finds the base signal, the display
shows SEARCHING...X, where X indicates the base
identification number.
5. The display will ask for the PIN to be entered. Enter the
4 digit PIN code (default = 0000) and press m.
6. You will hear a beep if the registration is successful. The
handset is automatically assigned an available handset
number. Use this number when making internal calls.
Note
If registration is not successful the first time, please repeat
the process again in case the base registration period ran
out of time. If the base is not found after a few seconds, the
handset returns to standby. Try registering again.
If there are already 4 handsets registered to the base, the
registration will fail. You must de-register another handset
before you can register a new one.
9.2
Select a base
If your handset is registered to more than one base (e.g. one
at work and one at home), you can select which base to use.
1. Press m, scroll d to REGISTER and press m. The
display shows SELECT BASE .
2. Press m. All the bases that your handset has been
registered to will be displayed, e.g. BASE 1 2 3 4 . The
currently selected base number flashes.
3. Press m to confirm. You will hear a confirmation beep
and the display will return to the previous menu.
Note
If you select AUTO, your handset will automatically search for
and connect to the base with the strongest signal.
9.2.1
De-register a handset
Use one handset to de-register another. You cannot
de-register the handset that you are using.
1. Press m, scroll d to SETUP and press m.
2. Scroll d to DEL HANDSET and press m.
3. Enter the 4 digit PIN code (default = 0000) and press
m.
4. Enter the handset number that you want to de-register.
5. You will hear a confirmation beep and the display will
return to the previous menu.
Each handset can be registered with up to four bases.
28
Using additional handsets
10. Help
No dial tone
• Use only the telephone line cord supplied.
• Check that the telephone line cord is connected properly.
• Check that the mains power is connected properly and
switched on.
No display
• Check that the batteries are inserted correctly and fully
charged. Use only approved rechargeable batteries
supplied.
• Check that the handset is switched on. Press and hold
flash.
• Reset the base by removing the batteries and
disconnecting the mains power. Wait for around 15
seconds before connecting it again. Allow up to one
minute for the handset and base to synchronize.
icon flashes
• Handset is out of range. Move closer to the base.
• Make sure that the handset is registered to the base
• Check that the mains power is connected properly and
switched on.
Keypad does not seem to work
• Check that the keypad lock is not on.
Help
icon is not scrolling during charge
• Adjust the handset slightly on the base.
• Clean the charging contacts with a cloth moistened with
alcohol.
• Check that the mains power is connected properly and
switched on.
• The battery is full. When the handset is fully charged,
icon will appear steadily on the display.
No Caller Display
• Check your subscription with your network operator.
• The caller may have withheld their number.
• The record cannot be found in your phonebook. Check
that you have the correct name/number stored in your
phonebook, with the full area code.
I have forgotten my PIN!
• Restore your C6I to its default settings.
• Cannot register a handset to the base
• You can register up to a maximum of 4 handsets to a C6I
base. You must deregister a handset in order to register
a new one.
• Check that you have entered the correct PIN code
(default = 0000).
• Check that you are at least one meter away from other
electrical equipment to avoid interference when
registering.
29
Handset does not ring
• The handset ringer volume may be set to Off.
Base unit does not ring
• The base ringer volume may be set to Off.
• Noise interference on my phone or on other electrical
equipment nearby.
• Place your phone at least one meter away from electrical
appliances or any metal obstructions to avoid any risk of
interference.
11. General information
IMPORTANT
This equipment is not designed to make emergency telephone
calls when the power fails. Alternative arrangements should be
made for access to emergency services.
This product is intended for connection to analogue public
switched telephone networks and private switchboards in
Philippines.
Important safety instructions
Follow these safety precautions when using your phone to
reduce the risk of fire, electric shock, and injury to persons
or property:
1. Keep all slits and openings of the phone unblocked. Do
not set the phone on a heating register or over a
radiator. Ensure that proper ventilation is provided at the
installation site.
2. Do not use while wet or while standing in water.
3. Do not use this product near water (for example, near a
bath tub, kitchen sink, or swimming pool).
4. Do not allow anything to rest on the power cord. Place
the power cord so that it will not be walked on.
5. Never insert objects of any kind into the product vents
as that may result in fire or electric shock.
30
General information
6. Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
7. Do not disassemble this product. If service or repair
work is required, contact the customer service helpline
found in this user's Guide.
8. Do not overload wall outlets and extension cords.
9. Avoid using during an electrical storm. Use a surge
protector to protect the equipment.
10. Do not use this phone to report a gas leak, especially if
you are in the vicinity of the gas line.
CAUTION
To reduce the risk of fire, use only the supplied power
adaptor.
Unplug this cordless phone immediately
from an outlet if:
• The power cord or plug is damaged or frayed.
• Liquid has been spilled on the product.
• The product has been exposed to rain or water. Do not
retrieve the handset or base until after you have
unplugged the power and phone from the wall. Then
retrieve the unit by the unplugged cords.
• The product has been dropped or the cabinet has been
damaged.
• The product exhibits a distinct change in performance.
General information
Installation Guidelines
1. Read and understand all instructions and save them for
future reference.
2. Follow all warnings and instructions marked on the
product.
3. Do not install this product near a bath tub, sink, or
shower.
4. Operate this phone using only the power source that is
indicated on the marking label. If you are unsure of the
power supply to your home, consult with your dealer or
local power company.
5. Do not place this product on an unstable cart, stand, or
table. This product may fall, causing serious damage to
the product.
6. Adjust only those controls that are covered by the
operating instructions. Improper adjustment of other
controls may result in damage and will often require
extensive work to restore the product to normal
operation.
7. Clean this product with a soft, damp cloth. Do not use
chemicals or cleaning agents to clean this phone.
8. Use only the power supply that came with this unit.
Using other power supplies may damage the unit.
9. Because this phone operates on electricity, you should
have at least one phone in your home that could operate
without electricity in the case the power in your home
goes out.
31
10. To avoid interference to nearby appliances, do not place
the base of the phone on or near a TV, microwave oven,
or VCR.
• Never use household polish as this will damage the
product. Never use a dry cloth as this may cause static
shock.
Battery Safety Instructions
Environmental
• Do not burn, disassemble, mutilate, or puncture the
battery. The battery contains toxic materials that could be
released, resulting in injury.
CAUTION
There is a risk of explosion if you replace the battery with an
incorrect battery type. Use only the battery pack that came
with your phone or an authorized replacement
recommended by the manufacturer.
• Keep battery packs out of the reach of children.
• Remove battery packs if storing over 30 days.
• Do not dispose of battery packs in fire, which could result
in explosion.
• The rechargeable battery packs that power this product
must be disposed of properly and may need to be
recycled. Refer to your battery’s label for battery type.
Contact your local recycling center for proper disposal
methods.
SAVE THESE INSTRUCTIONS
Cleaning
• Clean the handset and base (or charger) with a damp
(not wet) cloth, or an anti-static wipe.
32
• Do not expose to direct sunlight.
• The handset may become warm when the batteries are
being charged or during prolonged periods of use. This is
normal. However, we recommend that to avoid damage,
do not place the product on antique/veneered wood.
• Do not place your product on carpets or other surfaces
which generate fibres, or place it in locations preventing
the free flow of air over its surfaces.
• Do not submerge any part of your product in water and
do not use it in damp or humid conditions, such as
bathrooms.
• Do not expose your product to fire, explosives or other
hazardous conditions.
• There is a slight chance that your phone could be
damaged by an electrical storm. We recommend that you
unplug the power and telephone line cord during an
electrical storm.
Product disposal instructions
Product disposal instructions for residential users
When you have no further use for it, please remove any
batteries and dispose of them and the product according to
General information
your local authority’s recycling processes. For more
information, please contact your local authority or the retailer
where the product was purchased.
Product disposal instructions for business users
Business users should contact their suppliers and check the
terms and conditions of the purchase contract and ensure
that this product is not mixed with other commercial waste
for disposal.
Consumer Products and Accessories
Warranty
Thank you for purchasing this Motorola branded product
manufactured under license by Suncorp Technologies
Limited, 3001-3005 China Resources Building, 26 Harbour
Road, Wan Chai, Hong Kong. ("SUNCORP")
What Does this Warranty Cover?
Subject to the exclusions contained below, SUNCORP
warrants that this Motorola branded product ("Product") or
certified accessory ("Accessory") sold for use with this
product that it manufactured to be free from defects in
materials and workmanship under normal consumer usage
for the period outlined below. This Limited Warranty is your
exclusive warranty and is not transferable.
Who is covered?
This warranty extends only to the first consumer purchaser,
and is not transferable.
General information
What will SUNCORP do?
SUNCORP or its authorized distributor at its option and within
a commercially reasonable time, will at no charge repair or
replace any Products or Accessories that does not conform to
this limited warranty. We may use functionally equivalent
reconditioned/ refurbished/ pre-owned or new Products,
Accessories or parts.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO THE DURATION OF
THIS LIMITED WARRANTY, OTHERWISE THE REPAIR OR
REPLACEMENT PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF
THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OF IMPLIED. IN NO
EVENT SHALL MOTOROLA OR SUNCORP BE LIABLE,
WHETHER IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT OR ACCESSORY,
OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF
REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR OTHER FINANCIAL LOSS ARISING
OUT OF OR IN CONNECTION WITH THE ABILITY OR
INABILITY TO USE THE PRODUCTS OR ACCESSORIES
33
TO THE FULL EXTENT THESE DAMAGES MAY BE
DISCLAIMED BY LAW.
Some jurisdictions do not allow the limitation or exclusion of
incidental or consequential damages, or limitation on the
length of an implied warranty, so the above limitations or
exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights that
vary from one jurisdiction to another.
Products Covered
Consumer Products
Length of Coverage
One (1) year from the date of
the products original purchase
by the first consumer purchaser
of the product.
Consumer Accessories Ninety (90) days from the date
(battery, power supply(s) of the accessories original
and line cords)
purchase by the first consumer
purchaser of the product.
Consumer Products and The balance of the original
Accessories that are
warranty or for ninety (90) days
Repaired or Replaced
from the date returned to the
consumer, whichever is longer.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are
excluded from coverage.
Batteries. Only batteries whose fully charged capacity falls
below 80% of their rated capacity and batteries that leak are
covered by this limited warranty.
Abuse & Misuse. Defects or damage that result from: (a)
improper operation, storage, misuse or abuse, accident or
neglect, such as physical damage (cracks, scratches, etc.)
to the surface of the product resulting from misuse; (b)
contact with liquid, water, rain, extreme humidity or heavy
perspiration, sand, dirt or the like, extreme heat, or food; (c)
use of the Products or Accessories for commercial purposes
or subjecting the Product or Accessory to abnormal usage or
conditions; or (d) other acts which are not the fault of
Motorola or SUNCORP, are excluded from coverage.
Use of Non-Motorola branded Products and
Accessories. Defects or damage that result from the use of
Non-Motorola branded or certified Products or Accessories
or other peripheral equipment are excluded from coverage.
Unauthorized Service or Modification. Defects or
damages resulting from service, testing, adjustment,
installation, maintenance, alteration, or modification in any
way by someone other than Motorola, SUNCORP or its
authorized service centers, are excluded from coverage.
34
General information
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of
tampering; (c) mismatched board serial numbers; or (d)
nonconforming or non-Motorola branded housings, or parts,
are excluded from coverage.
Communication Services. Defects, damages, or the failure
of Products or Accessories due to any communication
service or signal you may subscribe to or use with the
Products or Accessories is excluded from coverage.
How to Obtain Warranty Service or Other
Information?
Technical Information
How many telephones can I have?
All items of telephone equipment have a Ringer Equivalence
Number (REN), which is used to calculate the number of
items which may be connected to any one telephone line.
Your C6I has a REN of 1. A total REN of 4 is allowed. If the
total REN of 4 is exceeded, the telephones may not ring.
With different telephone types, there is no guarantee of
ringing, even when the REN is less than 4.
Any additional handsets and chargers that you register have
a REN of 0.
To obtain service or information, please call: 659-1818.
R&TTE
You will receive instructions on how to ship the Products or
Accessories at your expense and risk, to a SUNCORP
Authorized Repair Center.
This equipment complies with the essential requirements for
the Radio Equipment and Telecommunications Terminal
Equipment Directive 1999/5/EC.
To obtain service, you must include: (a) the Product or
Accessory; (b) the original proof of purchase (receipt) which
includes the date, place and seller of the Product; (c) if a
warranty card was included in your box, a completed
warranty card showing the serial number of the Product; (d)
a written description of the problem; and, most importantly;
(e) your address and telephone number.
Connecting to a switchboard
General information
This product is intended for use within Philippines for
connection to the public telephone network.
Flash
You may need to use the flash function if you are connected
to a switch. Contact your PABX supplier for further
information.
35
Manufactured, distributed or sold by Suncorp
Technologies Ltd. , official licensee for this
product. MOTOROLA and the Stylized M Logo
are trademarks or registered trademarks of
Motorola Trademark Holdings, LLC. and are
used under license. All other trademarks are
the property of their respective owners. © 2011
Motorola Mobility, Inc. All rights reserved.
Version 2 (PH)