Bosch GTA3800 Operating instructions

OBJ_BUCH-1199-001.book Page 1 Thursday, April 8, 2010 1:35 PM
Robert Bosch GmbH
Power Tools Division
70745 Leinfelden-Echterdingen
Germany
GTA 3800 Professional
www.bosch-pt.com
1 609 929 U17 (2010.04) PS / 172 UNI
de
en
fr
es
pt
it
nl
Originalbetriebsanleitung
Original instructions
Notice originale
Manual original
Manual original
Istruzioni originali
Oorspronkelijke
gebruiksaanwijzing
da Original brugsanvisning
sv Bruksanvisning i original
no Original driftsinstruks
fi Alkuperäiset ohjeet
el
tr
pl
cs
sk
hu
ru
Πρωτότυπο οδηγιών χρήσης
Orijinal işletme talimat
Instrukcja oryginalna
Původní návod k používání
Pôvodný návod na použitie
Eredeti használati utasítás
Оригинальное руководство по эксплуатации
uk Оригінальна інструкція з
експлуатації
ro Instrucţiuni originale
bg Оригинална инструкция
sr
sl
hr
et
lv
lt
ar
fa
Originalno uputstvo za rad
Izvirna navodila
Originalne upute za rad
Algupärane kasutusjuhend
Instrukcijas oriģinālvalodā
Originali instrukcija
ΔϴϠλϷ΍ ϞϴϐθΘϟ΍ ΕΎϤϴϠόΗ
̶Ϡλ΍ έΎ̯ ίήσ ̵ΎϤϨϫ΍έ
OBJ_BUCH-1199-001.book Page 3 Thursday, April 8, 2010 1:35 PM
|3
7
8
6
5
1
2
3
4
11
2
10
9
12
13
14
GTA 3800 Professional
Bosch Power Tools
1 609 929 U17 | (4/8/10)
OBJ_BUCH-1199-001.book Page 4 Thursday, April 8, 2010 1:35 PM
4|
1 609 B01 854
1 609 929 U17 | (4/8/10)
1 609 B01 855
Bosch Power Tools
OBJ_BUCH-1199-001.book Page 5 Thursday, April 8, 2010 1:35 PM
|5
A1
10
15
A2
9
Bosch Power Tools
1 609 929 U17 | (4/8/10)
OBJ_BUCH-1199-001.book Page 6 Thursday, April 8, 2010 1:35 PM
6|
B1
B2
1
3
6
1
1 609 929 U17 | (4/8/10)
2
Bosch Power Tools
OBJ_BUCH-1199-001.book Page 7 Thursday, April 8, 2010 1:35 PM
|7
C1
C2
1
4
2
4
16
17
C3
C4
x
17
Bosch Power Tools
1 609 929 U17 | (4/8/10)
OBJ_BUCH-1199-001.book Page 8 Thursday, April 8, 2010 1:35 PM
8|
D
19
18
18
E
F
8
7
a
a
5
1 609 929 U17 | (4/8/10)
Bosch Power Tools
OBJ_BUCH-1199-001.book Page 9 Thursday, April 8, 2010 1:35 PM
|9
G
3
H
2
2
1
3
3
4
13
Bosch Power Tools
1 609 929 U17 | (4/8/10)
OBJ_BUCH-1199-001.book Page 10 Thursday, April 8, 2010 1:35 PM
10 |
I1
I2
20
11
12
J
11
12
1 609 929 U17 | (4/8/10)
Bosch Power Tools
OBJ_BUCH-1199-001.book Page 17 Thursday, April 8, 2010 1:35 PM
English | 17
Safety Notes
en
General Safety Rules
Read all warning notes and instructions enclosed with the saw stand
and the power tool to be mounted.
Failure to follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Safety Warnings for Saw Stands
f Pull the plug from the mains receptacle
and/or remove the battery from the power
tool before making adjustments on the tool
or changing tool accessories. Unintentional
switching on of the power tool is the cause of
many accidents.
f Assemble the saw stand in the proper manner before mounting the power tool. Proper
assembly is important to prevent the risk of
a collapse of the saw stand.
f Attach the power tool securely to the saw
stand before using it. Slipping off of the
power tool on the saw stand can lead to loss
of control.
f Place the saw stand on a firm, level and horizontal surface. If the saw stand can slip off
or wobbles, the power tool or the workpiece
cannot be uniformly and securely guided.
f Do not overload the saw stand and do not
use it as a ladder or scaffolding. Overloading or standing on the saw stand can lead to
the upward shifting of the centre of gravity of
the stand and its tipping over.
f Mount and dismount the power tool only
when it is in the transport position (for instructions on the transport position, also
see the operating instructions of the respective power tool). Otherwise, the power
tool can have such an unfavourable centre of
gravity that it cannot be held securely.
f When the power tool is mounted to the attachment set, operate it exclusively on the
saw stand. Without the saw stand, the attachment set with the power tool does not
stand securely and can tip over.
f Ensure that long and heavy workpieces do
not affect the equilibrium of the saw stand.
Long and/or heavy workpieces must be supported at the free end.
f Keep your fingers clear of the hinge points
while pushing the saw stand together or
pulling it apart. Danger of fingers being
crushed or contused.
Symbols
The following symbols can be important for the
operation of your saw stand. Please memorise
the symbols and their meanings. The correct interpretation of the symbols helps you operate
the saw stand better and more secure.
Symbol
250
kg
Meaning
The maximum carrying capacity (power tool + workpiece) of
the saw stand is 250 kg.
f When working or transporting, take care
that all bolts and connecting elements are
firmly tightened. The attachment sets for
the power tool must always be firmly
locked. Loose connections can lead to instability and inexact sawing.
Bosch Power Tools
1 609 929 U17 | (4/8/10)
OBJ_BUCH-1199-001.book Page 18 Thursday, April 8, 2010 1:35 PM
18 | English
Functional Description
14 Socket spanner (13 mm)/
Allen key (4 mm)/Phillips screwdriver
15 Locking pin
Intended Use
The saw stand is intended to accommodate the
following stationary saws from Bosch (as of
2010.03):
16 Button for releasing lever 17
17 Lever for locking the attachment set
18 Movable nut
19 Fastening kit, power tool
– GCM 8 S
3 601 L16 0..
20 Fastening kit for transport wheels*
– GCM 800 S
3 601 L16 1..
– GCM 10
0 601 B20 0..
– GCM 10 J
GCM 10 M
3 601 M20 2..
*Accessories shown or described are not part of the
standard delivery scope of the product. A complete
overview of accessories can be found in our accessories program.
– GCM 10 S
0 601 B20 5..
Technical Data
– GCM 10 SD
0 601 B22 5..
– GCM 12
0 601 B21 0..
– GCM 12 SD
0 601 B23 5..
Article number
– GTM 12
3 601 M15 0..
Length of saw stand
without table extension
mm
1578
Length of saw stand
with table extension
mm
3877
Height of saw stand
mm
824
kg
250
kg
150
kg
50
kg
22
Selected chop and mitre saws from other manufacturers can also be mounted.
Together with the power tool, the saw stand is
intended for the cutting to length of boards and
profiles.
Product Features
The numbering of the product features refers to
the illustration of the saw stand on the graphics
pages.
1 Workpiece support
2 Table extension
3 Locking knob of the table extension 2
4 Attachment set
5 Locking knob for height adjustment of the
roller stand 7
Saw stand
Max. carrying capacity
(power tool + workpiece)
without table extension
– Attachment set
Max. carrying capacity
(power tool + workpiece)
with table extension
– Attachment set
– Per table extension
Weight, approx.
GTA 3800
Professional
3 601 M24 000
6 Locking knob of the workpiece support 1
7 Roller stand
8 Length stop
9 Height-adjustable leg
10 Carrying handle
11 Transport stop*
12 Transport wheels*
13 Height-adjustable support leg of the table
extension 2*
1 609 929 U17 | (4/8/10)
Bosch Power Tools
OBJ_BUCH-1199-001.book Page 19 Thursday, April 8, 2010 1:35 PM
English | 19
Assembly
The saw stand is easily aligned with the heightadjustable leg 9.
Delivery Scope
Please also observe the representation of the delivery scope at the
beginning of the operating instructions.
Before assembling the saw stand, check if all
parts listed below are provided:
No.
Designation
Quantity
Saw stand GTA 3800
1
4
Attachment set
2
1
Workpiece support
2
7
Roller stand
2
14
Socket spanner/Allen key/
Phillips screwdriver
1
19
Power tool fastening kit
consisting of:
– Hexagon bolt
(M8 x 45)
– Washer
4
4
Additionally required tools (not in delivery
scope):
– Open-end spanner (10 mm)
Assembling the Saw Stand
– Carefully remove all parts included in the delivery from their packaging.
– Remove all packaging material.
Setting Up the Saw Stand (see figures A1 – A2)
– Lay the saw stand upside down on the floor
(legs facing upward).
– Push the locking pin 15 in and tilt the leg upward until the locking pin can be heard to engage.
– Repeat this workstep with the other three
legs.
– Turn around the saw stand to the working
position.
– Ensure that the saw stand is stable and that
all locking pins have engaged.
Bosch Power Tools
– Screw the leg in or out until the saw stand is
aligned level and all four legs face against the
floor.
Mounting the Roller Stand (see figure B1)
– Unscrew the Phillips screw of the roller
stand 7 with the Phillips screwdriver 14 provided.
If required, counter-hold the lock nut on the
other side of the roller stand using a spanner
(size 10 mm).
– Disassemble the roller stand 7.
There are different possibilities to arrange the
individual rollers to the workpiece support with
the internally-threaded rod (see figure).
– Arrange the individual parts as required and
slide the internally-threaded rod through the
rollers and the workpiece support 1.
– Screw all parts together again.
Mounting the Workpiece Support
(see figure B2)
– Loosen the locking knobs 3 and pull the table
extensions 2 via both sides of the saw stand
lightly outward.
– Slide the workpiece supports 1 from the left
and right each into the upper groove of the
saw stand or the table extension.
The length stops 8 must face outward.
– Tighten the locking knob 6 to lock the workpiece support.
Preparing the Saw Stand
Preparing the Attachment Sets
(see figures C1 – C4)
– To release the attachment sets 4, press buttons 16 each and open the levers 17.
– Measure the distance x between the mounting holes and your power tool.
– Position the attachment sets 4 centred on
the saw stand and at the matching clearance
x to each other.
– Lock the levers 17 again. The attachment
sets are now firmly positioned on the saw
stand.
1 609 929 U17 | (4/8/10)
OBJ_BUCH-1199-001.book Page 20 Thursday, April 8, 2010 1:35 PM
20 | English
Fastening the Power Tool to the Attachment
Sets (see figure D)
Sawing Workpieces of the Same Length
(see figure F)
– Position the power tool in the transport position.
Notes on the transport position are given in
the operating instructions of the respective
power tool.
– Position the movable nuts 18 in the attachment sets so that they match the mounting
holes of the power tool.
– Screw the attachment set and the power tool
with the hexagon bolts and the washers from
the fastening kit 19 using the provided socket spanner 14.
The length stop 8 can be used for easily sawing
workpieces to the same length.
Operation
Working Advice
Do not overload the saw stand. Always observe
the maximum carrying capacity of the saw stand
and the two table extensions.
Always hold the workpiece firmly, especially the
longer and more heavy section. After cutting
through the workpiece, the centre of gravity
may become dislocated in such an unfavourable
manner that the saw stand tips over.
Preparing the Workpiece Support
Long workpieces must be underlaid or supported at their free end.
Adjusting the Height of the Workpiece Support
(see figure E)
– Place your workpiece onto the saw table of
the power tool.
– Loosen locking knob 5 and adjust the height
of the roller stand 7 so that the workpiece
rests level.
– Retighten the locking knobs again.
1 609 929 U17 | (4/8/10)
– Pull the length stop 8 upward until it engages.
– Position the workpiece support 1 at the desired clearance to the saw blade of the power tool.
– To slide in the length stop 8, tilt it inward and
push it all the way down.
Extending the Saw Stand (see figure G)
The saw stand can be extended on both sides.
To stabilise the saw stand when working long
and heavy workpieces, the table extension 2 can
be supported with a support leg 13.
(see “Support Leg for Supporting the Table Extension”, page 20)
– Place your long workpiece onto the saw table
of the power tool.
– Release the respective locking knob 3 as required, and pull the table extension 2 out to
the desired position.
– Retighten the locking knobs again.
Fitting the Accessories
Support Leg for Supporting the Table Extension (see figure H)
To stabilise the saw stand when working long
and heavy workpieces, the table extension 2 can
be supported with a support leg 13.
The support leg 13 can be fastened either to the
left or right of the saw stand.
– Loosen locking knob 3 and pull the table extension 2 to be supported somewhat outward.
– Slide the screw head of the support leg 13 into the bottom groove of the table extension
2.
– Tighten the support leg 13.
– Screw the height adjustment of the support
leg 13 in or out until the saw table is aligned
level again.
Bosch Power Tools
OBJ_BUCH-1199-001.book Page 21 Thursday, April 8, 2010 1:35 PM
English | 21
Transport Wheels and Stop for Swift Changing
of the Location (see figures I1 – I2)
The transport wheels 12 enable the saw stand
to be transported to a different location, without having to remove the mounted stationary
saw.
The transport wheels 12 can be fastened either
to the left or right of the saw stand.
For assembly, use the fastening kit 20.
– Lay the saw stand upside down on the floor
(the folded-in legs facing upward).
– Screw the transport wheels at the desired location to the saw table with the four screws
and nuts.
Use the provided Allen key 14 for this.
– Turn around the saw stand to the working
position.
– Loosen the locking knob 3 on the side of the
saw stand on which the transport wheels are
fastened and pull the table extension 2 lightly outward.
– Insert the transport stop 11 into the upper
groove of the saw stand and slide the transport stop to the attachment set 4.
– Firmly tighten the hexagon bolt in the stop
with the provided socket spanner 14.
When transporting, the attachment set with
the mounted power tool can no longer slip
off.
Maintenance and Service
Maintenance and Cleaning
If the saw stand should fail despite the care taken in manufacture and testing, repair should be
carried out by an authorised customer services
agent for Bosch power tools.
In all correspondence and spare parts orders,
please always include the 10-digit article
number given on the type plate of the saw
stand.
Accessories
Attachment set. . . . . . . . . . . . . . 2 610 948 662
Workpiece support. . . . . . . . . . . 1 609 B01 851
Height-adjustable support leg . . 1 609 B01 855
Transport wheel set (wheels,
stop, fastening kit). . . . . . . . . . . 1 609 B01 854
Transport (see figure J)
The saw stand must be folded together for
transport.
– In case a support leg 13 is mounted, remove
it.
– Slide the table extensions 2 completely inward.
– Tilt all legs inward (press locking pin 15 inward; tilt each leg inward until the locking
pin can be heard to engage again).
– Grasp the recessed handle and lift up the
saw stand.
Bosch Power Tools
1 609 929 U17 | (4/8/10)
OBJ_BUCH-1199-001.book Page 22 Thursday, April 8, 2010 1:35 PM
22 | English
After-sales Service and Customer
Assistance
Our after-sales service responds to your questions concerning maintenance and repair of your
product as well as spare parts. Exploded views
and information on spare parts can also be
found under:
www.bosch-pt.com
Our customer service representatives can answer your questions concerning possible applications and adjustment of products and accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: +353 (01) 4 66 67 00
Fax: +353 (01) 4 66 68 88
Australia, New Zealand and Pacific Islands
Republic of South Africa
Customer service
Hotline: +27 (011) 6 51 96 00
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: +27 (011) 4 93 93 75
Fax: +27 (011) 4 93 01 26
E-Mail: bsctools@icon.co.za
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: +27 (031) 7 01 21 20
Fax: +27 (031) 7 01 24 46
E-Mail: bsc.dur@za.bosch.com
Western Cape – BSC Service Centre
Democracy Way, Prosperity Park
Milnerton
Tel.: +27 (021) 5 51 25 77
Fax: +27 (021) 5 51 32 23
E-Mail: bsc@zsd.co.za
Bosch Headquarters
Midrand, Gauteng
Tel.: +27 (011) 6 51 96 00
Fax: +27 (011) 6 51 98 80
E-Mail: rbsa-hq.pts@za.bosch.com
Disposal
The saw stand, accessories and packaging
should be sorted for environmental-friendly recycling.
Subject to change without notice.
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: +61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
1 609 929 U17 | (4/8/10)
Bosch Power Tools