Siemens RUGGEDCOM RS8000 Specifications

Preface
RUGGEDCOM RS8000
Introduction
1
Installing the Device
2
Communication Ports
3
Technical Specifications
4
Dimension Drawings
5
Certification
6
Installation Guide
11/2013
RUGGEDCOM RS8000
Installation Guide
Copyright © 2013 Siemens AG
All rights reserved. Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized
except where expressly permitted. Violations are liable for damages. All rights reserved, particularly for the purposes of patent application or
trademark registration.
This document contains proprietary information, which is protected by copyright. All rights are reserved. No part of this document may be
photocopied, reproduced or translated to another language without the prior written consent of Siemens AG.
Disclaimer Of Liability
Siemens has verified the contents of this manual against the hardware and/or software described. However, deviations between the product
and the documentation may exist.
Siemens shall not be liable for any errors or omissions contained herein or for consequential damages in connection with the furnishing,
performance, or use of this material.
The information given in this document is reviewed regularly and any necessary corrections will be included in subsequent editions. We
appreciate any suggested improvements. We reserve the right to make technical improvements without notice.
Registered Trademarks
ROX™, Rugged Operating System On Linux™, CrossBow™ and eLAN™ are trademarks of Siemens AG. ROS® is a registered trademark of
Siemens AG.
Other designations in this manual might be trademarks whose use by third parties for their own purposes would infringe the rights of the
owner.
Third Party Copyrights
Siemens recognizes the following third party copyrights:
• Copyright © 2004 GoAhead Software, Inc. All Rights Reserved.
Security Information
Siemens provides products and solutions with industrial security functions that support the secure operation of plants, machines, equipment
and/or networks. They are important components in a holistic industrial security concept. With this in mind, Siemens ’ products and solutions
undergo continuous development. Siemens recommends strongly that you regularly check for product updates.
For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g. cell protection concept)
and integrate each component into a holistic, state-of-the-art industrial security concept. Third-party products that may be in use should also
be considered. For more information about industrial security, visit http://www.siemens.com/industrialsecurity.
To stay informed about product updates as they occur, sign up for a product-specific newsletter. For more information, visit http://
support.automation.siemens.com.
Warranty
Siemens warrants this product for a period of five (5) years from the date of purchase, conditional upon the return to factory for maintenance
during the warranty term. This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all
warranties null and void. The warranties set forth in this article are exclusive and are in lieu of all other warranties, performance guarantees
and conditions whether written or oral, statutory, express or implied (including all warranties and conditions of merchantability and fitness for
a particular purpose, and all warranties and conditions arising from course of dealing or usage or trade). Correction of nonconformities in the
manner and for the period of time provided above shall constitute the Seller’s sole liability and the Customer’s exclusive remedy for defective
or nonconforming goods or services whether claims of the Customer are based in contract (including fundamental breach), in tort (including
negligence and strict liability) or otherwise.
For warranty details, visit www.siemens.com/ruggedcom or contact a Siemens customer service representative.
Contacting Siemens
ii
Address
Telephone
E-mail
Siemens AG
Industry Sector
300 Applewood Crescent
Concord, Ontario
Canada, L4K 5C7
Toll-free: 1 888 264 0006
Tel: +1 905 856 5288
Fax: +1 905 856 1995
ruggedcom.info.i-ia@siemens.com
Web
www.siemens.com/ruggedcom
RUGGEDCOM RS8000
Installation Guide
Table of Contents
Table of Contents
Preface ................................................................................................................
v
Alerts .................................................................................................................................................. v
Related Documents ............................................................................................................................. v
Accessing Documentation .................................................................................................................... v
Training .............................................................................................................................................. vi
Customer Support .............................................................................................................................. vi
Chapter 1
Introduction ..........................................................................................................
1
1.1 Feature Highlights ........................................................................................................................ 1
1.2 Ports, Controls and Indicator LEDs ............................................................................................... 2
Chapter 2
Installing the Device ............................................................................................
5
2.1 Mounting the Device .................................................................................................................... 5
2.1.1 Mounting the Device on a DIN Rail .................................................................................... 6
2.1.2 Mounting the Device to a Rack .......................................................................................... 6
2.1.3 Mounting the Device to a Panel ......................................................................................... 7
2.2 Connecting Power ........................................................................................................................ 8
2.2.1 Connecting AC Power ....................................................................................................... 9
2.2.2 Connecting DC Power ....................................................................................................... 9
2.3 Connecting the Failsafe Alarm Relay ........................................................................................... 10
2.4 Grounding the Device ................................................................................................................. 11
2.5 Connecting to the Device ........................................................................................................... 11
2.6 Cabling Recommendations ......................................................................................................... 12
Chapter 3
Communication Ports .........................................................................................
13
Chapter 4
Technical Specifications .....................................................................................
15
4.1 Power Supply Specifications ....................................................................................................... 15
4.2 Failsafe Relay Specifications ...................................................................................................... 15
4.3 Copper Ethernet Port Specifications ............................................................................................ 16
4.4 Fiber Optic Ethernet Port Specifications ....................................................................................... 16
4.5 Operating Environment ............................................................................................................... 16
iii
Table of Contents
RUGGEDCOM RS8000
Installation Guide
4.6 Mechanical Specifications ........................................................................................................... 17
Chapter 5
Dimension Drawings ..........................................................................................
19
Chapter 6
Certification ........................................................................................................
21
6.1 Agency Approvals ...................................................................................................................... 21
6.2 FCC Compliance ........................................................................................................................ 21
6.3 Industry Canada Compliance ...................................................................................................... 21
6.4 EMI and Environmental Type Tests ............................................................................................. 22
iv
RUGGEDCOM RS8000
Installation Guide
Preface
Preface
This guide describes the RUGGEDCOM RS8000. It describes the major features of the device, installation,
commissioning and important technical specifications.
It is intended for use by network technical support personnel who are responsible for the installation,
commissioning and maintenance of the device. It is also recommended for use by network and system planners,
system programmers, and line technicians.
Alerts
The following types of alerts are used when necessary to highlight important information.
DANGER!
DANGER alerts describe imminently hazardous situations that, if not avoided, will result in death or
serious injury.
WARNING!
WARNING alerts describe hazardous situations that, if not avoided, may result in serious injury and/or
equipment damage.
CAUTION!
CAUTION alerts describe hazardous situations that, if not avoided, may result in equipment damage.
IMPORTANT!
IMPORTANT alerts provide important information that should be known before performing a procedure
or step, or using a feature.
NOTE
NOTE alerts provide additional information, such as facts, tips and details.
Related Documents
Other documents that may be of interest include:
• ROS User Guide for the RS8000
Accessing Documentation
The latest Hardware Installation Guides and Software User Guides for most RUGGEDCOM products are
available online at www.siemens.com/ruggedcom.
Alerts
v
Preface
RUGGEDCOM RS8000
Installation Guide
For any questions about the documentation or for assistance finding a specific document, contact a Siemens
sales representative.
Training
Siemens offers a wide range of educational services ranging from in-house training of standard courses on
networking, Ethernet switches and routers, to on-site customized courses tailored to the customer's needs,
experience and application.
Siemens' Educational Services team thrives on providing our customers with the essential practical skills to make
sure users have the right knowledge and expertise to understand the various technologies associated with critical
communications network infrastructure technologies.
Siemens' unique mix of IT/Telecommunications expertise combined with domain knowledge in the utility,
transportation and industrial markets, allows Siemens to provide training specific to the customer's application.
For more information about training services and course availability, visit www.siemens.com/ruggedcom or
contact a Siemens sales representative.
Customer Support
Customer support is available 24 hours, 7 days a week for all Siemens customers. For technical support or
general information, please contact Customer Support at:
Toll Free (North America): 1 866 922 7975
International: +1 905 856 5288
Website: http://support.automation.siemens.com
vi
Training
RUGGEDCOM RS8000
Installation Guide
Chapter 1
Introduction
Introduction
The RUGGEDCOM RS8000 provides substation hardened, fully managed, Ethernet switches specifically
designed to operate reliably in electrically and environmentally harsh environments.
The RS8000’s Zero-Packet-Loss technology provides a high level of immunity to electromagnetic interference
(EMI) and heavy electrical surges typical of environments found in electric utility substations, industrial plant
floors or in curb side traffic control cabinets. The RS8000 model provides IEEE 1613 Class 2 error-free
communications performance under EMI stress. An operating temperature range of -40 to 85 °C (-40 to 185 °F)
allows the RS8000 to be placed in almost any location.
The RS8000 provides a wide range of power supply options suitable for multiple industries and for worldwide
operability. Options include 24 VDC, 48 VDC, and HI (88-300 VDC or 85-264 VAC)
The RS8000 offers advanced Layer 2 and 3 networking features and network management via the Rugged
Operating System (ROS). A unique feature of ROS is the performance of its IEEE 802.1w Rapid Spanning Tree
Protocol (RSTP) used for implementing fault tolerant ring and mesh network architectures. The protocol has been
optimized to support ring sizes of up to 160 switches and fault recovery times in the order of less than 5 ms per
switch.
The RS8000’s superior ruggedized design coupled with the Rugged Operating System (ROS) provides improved
system reliability and advanced networking features making it ideally suited for creating Ethernet networks for
mission-critical, real-time control applications.
Section 1.1
Feature Highlights
Ethernet Ports
• Eight 100Base-FX
• Multi-mode and single-mode optical transceivers
• Industry standard fiber optical connectors: MTRJ, LC
Rated for Reliability in Harsh Environments
• Immunity to EMI and heavy electrical surges
▪ Zero-Packet-Loss™ Technology
▪ Meets IEEE 1613 Class 2 (electric utility substations)
▪ Exceeds IEC 61850-3 (electric utility substations)
▪ Exceeds IEC 61800-3 (variable speed drive systems)
▪ Exceeds IEC 61000-6-2 (generic industrial)
▪ Exceeds NEMA TS-2 (traffic control equipment)
• -40 to 85 °C (-40 to 185 °F) operating temperature (no fans)
• Failsafe Output Relay: For critical failure or error alarming
• Conformal coated printed circuit boards (optional)
Feature Highlights
1
Chapter 1
Introduction
RUGGEDCOM RS8000
Installation Guide
Cyber Security Features
• Multi-level user passwords
• SSH/SSL (128-bit encryption)
• Enable/disable ports, MAC based port security
• Port based network access control (802.1x)
• VLAN (802.1Q) to segregate and secure network traffic
• RADIUS centralized password management
• SNMPv3 authentication and 56-bit encryption
Management Tools
• Web-based, Telnet, CLI management interfaces
• SNMP v1/v2/v3 (56-bit encryption)
• Remote Monitoring (RMON)
• Rich set of diagnostics with logging and alarms
Universal Power Supply Options
• Universal high-voltage range: 88-300 VDC or 85-264 VAC
• Popular low voltage ranges: 24 VDC (10-36 VDC), 48 VDC (36-59 VDC)
• Terminal blocks for reliable maintenance free connections
• CSA/UL 60950 safety approved to 85 °C (185 °F)
Section 1.2
Ports, Controls and Indicator LEDs
The RS8000 features various ports, controls and indicator LEDs on the front and rear panels for configuring and
troubleshooting the device.
2
Ports, Controls and Indicator LEDs
RUGGEDCOM RS8000
Chapter 1
Installation Guide
Introduction
2
4
3
3
1
1
Figure 1: Front and Rear Panels
1. Power Indicator LED
2. Reset Button
Power Indicator LED
3. Port Status Indicator LEDS
4. RS232 Serial Console Port (DB9)
This LED indicates the status of the power supply.
• Green = The power supply is supplying power
• Off = Power is off
Reset Button
The reset button shuts down and restarts the device.
Port Status Indicator LEDs
These LEDs indicate when serial ports are active.
LED
State
Meaning
Link
Solid
Link detected
Off
No link detected
Blinking
Link activity (receiving)
Off
No link activity
Blinking
Link activity (transmitting)
Off
No link activity
RX
TX
RS232 Serial Console Port
Ports, Controls and Indicator LEDs
This port is for interfacing directly with the device and accessing initial management
functions.
3
RUGGEDCOM RS8000
Installation Guide
Ports, Controls and Indicator LEDs
Chapter 1
Introduction
4
RUGGEDCOM RS8000
Installation Guide
Chapter 2
Installing the Device
Installing the Device
The following sections describe how to install the device, including mounting the device, installing/removing
modules, connecting power, and connecting the device to the network.
DANGER!
Electrocution hazard – risk of serious personal injury and/or damage to equipment. Before performing
any maintenance tasks, make sure all power to the device has been disconnected and wait
approximately two minutes for any remaining energy to dissipate.
IMPORTANT!
This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall
render all warranties null and void.
Changes or modifications not expressly approved by Siemens AG could invalidate specifications, test
results, and agency approvals, and void the user's authority to operate the equipment.
IMPORTANT!
This product should be installed in a restricted access location where access can only be gained by
authorized personnel who have been informed of the restrictions and any precautions that must be
taken. Access must only be possible through the use of a tool, lock and key, or other means of security,
and controlled by the authority responsible for the location.
• Section 2.1, “Mounting the Device”
• Section 2.2, “Connecting Power”
• Section 2.3, “Connecting the Failsafe Alarm Relay”
• Section 2.4, “Grounding the Device”
• Section 2.5, “Connecting to the Device”
• Section 2.6, “Cabling Recommendations”
Section 2.1
Mounting the Device
The RS8000 is designed for maximum mounting and display flexibility. It can be equipped with connectors that
allow it to be installed in a 48 cm (19 in) rack, 35 mm (1.4 in) DIN rail, or directly on a panel.
NOTE
For detailed dimensions of the device with either rack, DIN rail or panel hardware installed, refer to
Chapter 5, Dimension Drawings.
The following sections describe the various methods of mounting the device:
• Section 2.1.1, “Mounting the Device on a DIN Rail”
• Section 2.1.2, “Mounting the Device to a Rack”
• Section 2.1.3, “Mounting the Device to a Panel”
Mounting the Device
5
Chapter 2
RUGGEDCOM RS8000
Installing the Device
Installation Guide
Section 2.1.1
Mounting the Device on a DIN Rail
To mount the device to a standard 35 mm (1.4 in) DIN rail, do the following:
1.
Align the adapters with the DIN rails and slide the device into place.
Figure 2: DIN Rail Mounting
1. Panel/DIN Rail Adaptor
2.
2. DIN Rail
3. Screw
Install one of the supplied screws on either side of the device to secure the adapters to the DIN rails.
Section 2.1.2
Mounting the Device to a Rack
To secure the device to a standard 48 cm (19 in) rack, do the following:
1.
Remove the four screws from the side of the device.
2.
Insert the device into rack mount adapter and use the screws to secure it.
NOTE
The device can be installed with the communication ports facing the front or rear of the rack,
depending on the desired orientation.
6
Mounting the Device on a DIN Rail
RUGGEDCOM RS8000
Chapter 2
Installation Guide
Installing the Device
1
2
Figure 3: Rack Mounting
1. Rack Mount Adapter
3.
2. Screw
Insert the rack mount adapter and device assembly into the rack.
NOTE
Since heat within the device is channelled to the enclosure, it is recommended that 1 rack-unit
of space, or 44 mm (1.75 in), be kept empty above the device. This allows a small amount of
convectional airflow.
Forced airflow is not required. However, any increase in airflow will result in a reduction of ambient
temperature and improve the long-term reliability of all equipment mounted in the rack space.
4.
Secure the adapter to the rack using the supplied hardware.
Section 2.1.3
Mounting the Device to a Panel
To mount the device to a panel, do the following:
1.
Place the device against the panel and align the adapters with the mounting holes.
Mounting the Device to a Panel
7
Chapter 2
RUGGEDCOM RS8000
Installing the Device
Installation Guide
1
1
2
2
1
1
Figure 4: Panel Mounting
1. Screw
2.
2. Panel/DIN Rail Adaptor
Install the supplied screws to secure the adapters to the panel.
Section 2.2
Connecting Power
The RS8000 supports a single integrated high AC/DC or low DC power supply
NOTE
• For 88-300 VDC rated equipment, an appropriately rated circuit breaker must be installed.
• For 100-240 VAC rated equipment, an appropriately rated circuit breaker must be installed.
• A circuit breaker is not required for 12, 24 or 48 VDC rated equipment.
• Power input terminals have reverse polarity protection for 12, 24 and 48 VDC rated equipment.
• Equipment must be installed according to applicable local wiring codes and standards.
The following sections describe how to connect power to the device:
• Section 2.2.1, “Connecting AC Power”
8
Connecting Power
RUGGEDCOM RS8000
Chapter 2
Installation Guide
Installing the Device
• Section 2.2.2, “Connecting DC Power”
Section 2.2.1
Connecting AC Power
To connect a high AC power supply to the device, do the following:
CAUTION!
Electrical hazard – risk of damage to equipment. Before testing the dielectric strength (HIPOT) in the
field, remove the braided ground cable connected to the surge ground terminal and chassis ground.
This cable connects transient suppression circuitry to chassis ground and must be removed in order to
avoid damage to transient suppression circuitry during testing.
1.
Connect the positive wire from the power source to the positive/hot (+/H) terminal on the terminal block.
1
2
3
Figure 5: Terminal Block Wiring
1. Positive/Hot (+/H) Terminal
2. Negative/Neutral (-/N) Terminal
3. Surge Ground Terminal
4. Braided Ground Cable
2.
Connect the negative wire from the power source to the negative/neutral (-/N) terminal on the terminal block.
3.
Using a braided wire or other appropriate grounding wire, connect the surge ground terminal to the chassis
ground connection. The surge ground terminal is used as the ground conductor for all surge and transient
suppression circuitry internal to the unit.
4.
Connect the ground terminal on the power source to the chassis ground terminal on the device. For more
information, refer to Section 2.4, “Grounding the Device”.
Section 2.2.2
Connecting DC Power
To connect a high or low DC power supply to the device, do the following:
CAUTION!
Electrical hazard – risk of damage to equipment. Before testing the dielectric strength (HIPOT) in the
field, remove the braided ground cable connected to the surge ground terminal and chassis ground.
Connecting AC Power
9
Chapter 2
RUGGEDCOM RS8000
Installing the Device
Installation Guide
This cable connects transient suppression circuitry to chassis ground and must be removed in order to
avoid damage to transient suppression circuitry during testing.
1.
Connect the positive wire from the power source to the positive/hot (+/L) terminal on the terminal block.
1
2
3
Figure 6: Terminal Block Wiring
1. Positive/Hot (+/L) Terminal
2. Negative/Neutral (-/N) Terminal
3. Surge Ground Terminal
4. Braided Ground Cable
2.
Connect the negative wire from the power source to the negative/neutral (-/N) on the terminal block.
3.
Using a braided wire or other appropriate grounding wire, connect the surge ground terminal to the chassis
ground connection. The surge ground terminal is used as the ground conductor for all surge and transient
suppression circuitry internal to the unit.
4.
Connect the ground terminal on the power source to the chassis ground terminal on the device. For more
information, refer to Section 2.4, “Grounding the Device”.
Section 2.3
Connecting the Failsafe Alarm Relay
The failsafe relay can be configured to latch based on alarm conditions. The NO (Normally Open) contact is
closed when the unit is powered and there are no active alarms. If the device is not powered or if an active alarm
is configured, the relay opens the NO contact and closes the NC (Normally Closed) contact.
NOTE
Control of the failsafe relay output is configurable through ROS . One common application for this relay
is to signal an alarm if a power failure occurs. For more information, refer to the ROS User Guide for
the RS8000.
The following shows the proper relay connections.
10
Connecting the Failsafe Alarm Relay
RUGGEDCOM RS8000
Chapter 2
Installation Guide
Installing the Device
1
2
3
Figure 7: Failsafe Alarm Relay Wiring
1. Normally Open
2. Common
3. Normally Closed
Section 2.4
Grounding the Device
The RS8000 chassis ground terminal uses a #6-32 screw. It is recommended to terminate the ground connection
with a #6 ring lug and torque it to 1.7 N·m (15 lbf·in).
2
3
1
Figure 8: Chassis Ground Connection
1. Stainless Steel Stud
2. #6-32 Screw
3. #6 Ring Lug
Section 2.5
Connecting to the Device
The following describes the various methods for accessing the ROS console and Web interfaces on the device.
For more detailed instructions, refer to the ROS User Guide for the RS8000.
Serial Console Port
Connect a PC or terminal directly to the serial console port to access the boot-time control and ROS console
interface.
Grounding the Device
11
Chapter 2
RUGGEDCOM RS8000
Installing the Device
Installation Guide
IMPORTANT!
The serial console port is intended to be used only as temporary connections during initial
configuration or troubleshooting.
The serial console port implements RS232 DCE (Data Communication Equipment) on a DB9 connector. The
following is the pin-out for the port:
Pin
5
1
Name
1
Reserved (Do Not Connect)
2
RX
Receive Data
3
TX
Transmit Data
4
5
9
6
Figure 9: Serial DB9 Console Port
Description
Reserved (Do Not Connect)
GND
Signal Ground
6
Reserved (Do Not Connect)
7
Reserved (Do Not Connect)
8
Reserved (Do Not Connect)
9
Reserved (Do Not Connect)
Communication Ports
Connect any of the available Ethernet ports on the device to a management switch and access the ROS console
and Web interfaces via the device's IP address. For more information about available ports, refer to Chapter 3,
Communication Ports.
Section 2.6
Cabling Recommendations
Siemens does not recommend the use of copper cabling of any length for critical, real-time substation automation
applications. All copper Ethernet ports on RUGGEDCOM products include transient suppression circuitry
to protect against damage from electrical transients and conform with IEC 61850-3 and IEEE 1613 Class 1
standards. This means that during a transient electrical event, communications errors or interruptions may occur,
but recovery is automatic.
Siemens also does not recommend using copper Ethernet ports to interface with devices in the field across
distances that could produce high levels of ground potential rise (i.e. greater than 2500 V), during line-to-ground
fault conditions.
12
Cabling Recommendations
RUGGEDCOM RS8000
Chapter 3
Installation Guide
Communication Ports
Communication Ports
Fiber optic Ethernet ports are available with either MTRJ (Mechanical Transfer Registered Jack) or LC (Lucent
Connector) connectors. Make sure the Transmit (Tx) and Receive (Rx) connections of each port are properly
connected and matched to establish a proper link.
1
Figure 10: MTRJ Port
1. Tx Connector
2. Rx Connector
1
2
2
Figure 11: LC Port
1. Tx Connector
2. Rx Connector
For specifications on the available fiber optic Ethernet ports, refer to Section 4.4, “Fiber Optic Ethernet Port
Specifications”.
13
RUGGEDCOM RS8000
Installation Guide
Chapter 3
Communication Ports
14
RUGGEDCOM RS8000
Chapter 4
Installation Guide
Technical Specifications
Technical Specifications
The following sections provide important technical specifications related to the device and available modules:
• Section 4.1, “Power Supply Specifications”
• Section 4.2, “Failsafe Relay Specifications”
• Section 4.3, “Copper Ethernet Port Specifications”
• Section 4.4, “Fiber Optic Ethernet Port Specifications”
• Section 4.5, “Operating Environment”
• Section 4.6, “Mechanical Specifications”
Section 4.1
Power Supply Specifications
Power Supply Type
Input Range
Internal Fuse Rating
Minimum
Maximum
12-24 VDC
10 VDC
36 VDC
6.3 A(F)
24 VDC
18 VDC
36 VDC
5 A(F)
48 VDC
36 VDC
59 VDC
3.15 A(T)
d
88 VDC
300 VDC
3.15 A(T)
d
85 VAC
265 VAC
3.15 A(T)
HI (125/250 VDC)
HI (110/230 VAC)
ab
Maximum Power
c
Consumption
15 W
a
(F) denotes fast-acting fuse
b
(T) denotes time-delay fuse.
c
Power consumption varies based on configuration. 10/100Base-TX ports consume roughly 1 W less than fiber optic ports.
d
This is the same power supply for both AC and DC.
Section 4.2
Failsafe Relay Specifications
Power Supply Specifications
Voltage
Current
30 VAC
0.3 A
30 VDC
1A
80 VDC
0.3 A
15
Chapter 4
RUGGEDCOM RS8000
Technical Specifications
Installation Guide
Section 4.3
Copper Ethernet Port Specifications
The following details the specifications for copper Ethernet ports that can be ordered with the RS8000.
Speed
e
Connector
Duplex
e
Cable Type
f
Wiring Standard
Maximum Distance
Isolation
10/100Base-TX
RJ45
FDX/HDX
> Category 5
TIA/EIA T568A/B
100 m (328 ft)
1.5 kV
e
Auto-negotiating.
f
Shielded or unshielded.
g
Auto-crossover and auto-polarity.
h
Typical distance. Dependent on the number of connectors and splices.
i
RMS 1 minute.
g
h
i
Section 4.4
Fiber Optic Ethernet Port Specifications
The following details fiber optic specifications for ports that can be equipped on the RS8000 . The user
determines the type of optics at the time of ordering, and can determine the ports installed on a particular unit by
reading the factory data file via the ROS user interface. The specifications are organized by order code. Module
order codes are contained within each unit when it is assembled and configured at the factory. For information
about obtaining factory configuration data, refer to the ROS User Guide for the RS8000.
Connector
Type
Cable
Type (μm)
Tx λ (typ.)
(nm)
Tx min.
(dBm)
Tx max.
(dBm)
Rx
Sensitivity
(dBm)
Rx
Saturation
(dBm)
Distance
(typ.) (km)
Power
Budget
(dB)
MM
MTRJ
50/125
1310
-16
-11
-33.5
-11
2
17
SM
LC
9/125
1310
-15
-8
-31
-5
15
16.5
Mode
j
j
MM = Multi-Mode, SM = Single-Mode
Section 4.5
Operating Environment
16
Parameter
Range
Comments
Ambient Operating Temperature
-40 to 85°C
Ambient Temperature as measured from a
30 cm radius surrounding the center of the
enclosure.
Ambient Relative Humidity
5% to 95%
Non-condensing
Ambient Storage Temperature
-40 to 85°C
Copper Ethernet Port Specifications
RUGGEDCOM RS8000
Chapter 4
Installation Guide
Technical Specifications
Section 4.6
Mechanical Specifications
Parameter
Value
Dimensions
Refer to Chapter 5, Dimension Drawings
Weight
2.25 kg (5 lbs)
Ingress Protection
IP40 (1 mm or 0.04 in objects)
Enclosure
18 AWG Galvanized Steel
Mechanical Specifications
17
RUGGEDCOM RS8000
Installation Guide
Mechanical Specifications
Chapter 4
Technical Specifications
18
RUGGEDCOM RS8000
Chapter 5
Installation Guide
Dimension Drawings
Dimension Drawings
NOTE
All dimensions are in millimeters, unless otherwise stated.
172.2
49.3
198.3
248.9
Figure 12: Overall Dimensions
19
Chapter 5
RUGGEDCOM RS8000
Dimension Drawings
Installation Guide
34.7
18.8
6.1
479.4
464.5
66.7
50.6
Figure 13: Rack Mount Dimensions
274.3
61.8
63.8
101.6
264.2
Figure 14: Panel and Din Rail Mount Dimensions
20
RUGGEDCOM RS8000
Chapter 6
Installation Guide
Certification
Certification
The RS8000 device has been thoroughly tested to guarantee its conformance with recognized standards and has
received approval from recognized regulatory agencies.
• Section 6.1, “Agency Approvals”
• Section 6.2, “FCC Compliance”
• Section 6.3, “Industry Canada Compliance”
• Section 6.4, “EMI and Environmental Type Tests”
Section 6.1
Agency Approvals
The RS8000 has received approval from various agencies.
Agency
Standards
Comments
CSA
CSA C22.2 No. 60950-1, UL 60950-1
Approved
CE
EN 60950-1, EN 61000-6-2, EN
50581, EN 55022, EN 60825-1
CE Compliance is claimed via
Declaration of Self Conformity Route
FCC
FCC Part 15, Class A
Approved
Section 6.2
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference on his own expense.
Section 6.3
Industry Canada Compliance
CAN ICES-3 (A) / NMB-3 (A)
Agency Approvals
21
Chapter 6
RUGGEDCOM RS8000
Certification
Installation Guide
Section 6.4
EMI and Environmental Type Tests
The RS8000 has passed the following EMI and environmental tests.
IEC 61850-3 Type Tests
Test
IEC 61000-4-2
Description
ESD
Test Levels
Severity Levels
Enclosure
Contact
+/- 8 kV
4
Enclosure Air
+/- 15 kV
4
IEC 61000-4-3
Radiated RFI
Enclosure ports
20 V/m
x
IEC 61000-4-4
Burst (Fast Transient)
Signal ports
+/- 4 kV @ 2.5 kHz
x
DC Power ports
+/- 4 kV
4
AC Power ports
+/- 4 kV
4
Earth
ground ports
+/- 4 kV
4
Signal ports
+/- 4 kV line-to-earth,
+/- 2 kV line-to-line
4
DC Power ports
+/- 2 kV line-to-earth,
+/- 1 kV line-to-line
3
AC Power ports
+/- 4 kV line-to-earth,
+/- 2 kV line-to-line
4
Signal ports
10 V
3
DC Power ports
10 V
3
AC Power ports
10 V
3
Earth
ground ports
10 V
3
IEC 61000-4-5
IEC 61000-4-6
Surge
Induced (Conducted) RFI
IEC 61000-4-8
Magnetic Field
Enclosure ports
40 A/m continuous, 1000 A/m for 1 s
IEC 61000-4-29
Voltage Dips and Interrupts
DC Power ports
30% for 0.1 s, 60% for
0.1 s, 100% for 0.05 s
AC Power ports
30% for 1 period, 60% for 50 periods
IEC 61000-4-11
IEC 61000-4-12
IEC 61000-4-16
IEC 61000-4-17
22
100% for 5 periods,
100% for 50 periods
Damped Oscillatory
Mains Frequency Voltage
Ripple on DC Power Supply
Signal ports
2.5 kV common, 1 kV
differential mode @ 1 MHz
3
DC Power ports
2.5 kV common, 1 kV
differential mode @ 1 MHz
3
AC Power ports
2.5 kV common, 1 kV
differential mode @ 1 MHz
3
Signal ports
30 V Continuous, 300 V for 1 s
4
DC Power ports
30 V Continuous, 300 V for 1 s
4
DC Power ports
10%
3
EMI and Environmental Type Tests
RUGGEDCOM RS8000
Chapter 6
Installation Guide
Certification
Test
Description
IEC 60255-5
Dielectric Strength
HV Impulse
Test Levels
Severity Levels
Signal ports
2 kVAC (Fail-Safe Relay output)
DC Power ports
1.5 kVDC
AC Power ports
2 kVDC
Signal ports
5 kV (Fail-Safe Relay Output)
DC Power ports
5 kV
AC Power ports
5 kV
IEEE 1613 (C37.90.x) EMI Immunity Type Tests
NOTE
The RS8000 meets Class 2 requirements for an all-fiber configuration and Class 1 requirements for
copper ports.
IEEE Test
IEEE 1613
Clause
C37.90.3
9
Description
ESD
Test Levels
Enclosure Contact
+/- 8 kV
Enclosure Air
+/- 15 kV
C37.90.2
8
Radiated RFI
Enclosure ports
35 V/m
C37.90.1
7
Fast Transient
Signal ports
+/- 4 kV @ 2.5 kHz
DC Power ports
+/- 4 kV
AC Power ports
+/- 4 kV
Earth ground ports
+/- 4 kV
Signal ports
2.5 kV common mode @ 1MHz
DC Power ports
2.5 kV common and
differential mode @ 1MHz
AC Power ports
2.5 kV common and
differential mode @ 1MHz
Signal ports
5 kV (Failsafe Relay)
DC Power ports
5 kV
AC Power ports
5 kV
Signal ports
2 kVAC (Failsafe Relay)
DC Power ports
1.5 kVDC
AC Power ports
2 kVAC
Oscillatory
C37.90
6
HV Impulse
Dielectric
Strength
Environmental Type Tests
Test
Description
Test Levels
IEC 60068-2-1
Cold Temperature
Test Ad
-40 °C (-40 °F), 16 Hours
IEC 60068-2-2
Dry Heat
Test Bd
85 °C (185 °F), 16 Hours
EMI and Environmental Type Tests
Severity Levels
23
Chapter 6
RUGGEDCOM RS8000
Certification
Installation Guide
Test
IEC 60068-2-30
24
Description
Humidity (Damp
Heat, Cyclic)
Test Levels
Test Db
Severity Levels
95% (non-condensing),
55 °C (131 °F), 6 cycles
IEC 60255-21-1
Vibration
2 g @ 10-150 Hz
Class 2
IEC 60255-21-2
Shock
30 g @ 11 ms
Class 2
EMI and Environmental Type Tests