Epson EasyMP Network Projection User`s guide

PowerLite® 1830
Choose from the following connections:
Computer Monitor Port
Connect a computer using the VGA cable that came with the projector.
Component video to VGA cable*
Audio cable*
Connect the projector
VGA cable
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
S-Video cable*
Connect up to 4 video devices and use the remote control to switch
between them.
RCA video cable (composite video)*
Quick Setup
Video Player
3
Using the remote control
Open the A/V Mute slide all the way.
Make sure the batteries are installed as shown (two AA batteries).
4
Press the
power button on the projector or remote control.
Power light
Turn projector
on and off
Choose which
source to display
Power button
Turn off projector
display and sound
Change
presentation
slides (USB
connection only)
* These cables are optional.
Connect one end to the projector’s Computer1 or Computer2 port, and the
other end to your computer’s
monitor port. If you are using a notebook,
switch it to external display. You can also connect an audio cable.
Camera or USB Device
The power light flashes green, then stays on.
Connect a digital camera, Epson Document Camera, or other USB device to the
projector’s USB Type A (flat) port.
NOTE: To shut down the projector, press the
power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
Computer USB Port
Connect a computer (Windows® 2000 or later only) using the USB cable that
came with the projector.
Connect the square end of the USB cable to the projector’s USB
TypeB
(square) port. Connect the flat end of the cable to any USB port on your
computer.
Digital camera
Thumb drive
Adjust the image
1
If you don’t see an image, press the Source Search button on the
projector or the remote control to select the image source.
NOTE: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
To raise the image, press the gray foot release lever and lift the front of
the projector. Release the lever to lock the foot in position.
3
Turn the focus ring to sharpen the image.
DC-06 document camera
If you connect a digital camera or USB storage device, you can use the
projector’s Slideshow feature. See the Network and PC Free Operation Guide on
your projector CD.
Follow the on-screen instructions to install the Epson USB Display software.
(You need to install the software only the first time you connect.) Then press
the USB button on the remote control.
Network (LAN)
Connect the projector to your network using an Ethernet® cable. See
“Network Configuration” on the back of this sheet for more information.
For information on connecting an external monitor or external speakers, see
the User’s Guide on your projector CD.
Turn on your equipment
1
2
Turn the zoom ring to reduce or enlarge the image.
Turn on your computer or video source.
Plug in the projector.
Focus
Zoom
*411783500*
*411783500*
4
If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely.
5
If your image looks like
projector to correct it.
or
, press the
or
buttons on the
Control projector volume
Navigate
projector
menus
You can use the remote control to operate the projector. With the USB cable,
you can use the remote as a wireless mouse. For more information on using
the remote control, see your User’s Guide.
PowerLite® 1830
Choose from the following connections:
Computer Monitor Port
Connect a computer using the VGA cable that came with the projector.
Component video to VGA cable*
Audio cable*
Connect the projector
VGA cable
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
S-Video cable*
Connect up to 4 video devices and use the remote control to switch
between them.
RCA video cable (composite video)*
Quick Setup
Video Player
3
Using the remote control
Open the A/V Mute slide all the way.
Make sure the batteries are installed as shown (two AA batteries).
4
Press the
power button on the projector or remote control.
Power light
Turn projector
on and off
Choose which
source to display
Power button
Turn off projector
display and sound
Change
presentation
slides (USB
connection only)
* These cables are optional.
Connect one end to the projector’s Computer1 or Computer2 port, and the
other end to your computer’s
monitor port. If you are using a notebook,
switch it to external display. You can also connect an audio cable.
Camera or USB Device
The power light flashes green, then stays on.
Connect a digital camera, Epson Document Camera, or other USB device to the
projector’s USB Type A (flat) port.
NOTE: To shut down the projector, press the
power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
Computer USB Port
Connect a computer (Windows® 2000 or later only) using the USB cable that
came with the projector.
Connect the square end of the USB cable to the projector’s USB
TypeB
(square) port. Connect the flat end of the cable to any USB port on your
computer.
Digital camera
Thumb drive
Adjust the image
1
If you don’t see an image, press the Source Search button on the
projector or the remote control to select the image source.
NOTE: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the back of this sheet.
2
To raise the image, press the gray foot release lever and lift the front of
the projector. Release the lever to lock the foot in position.
3
Turn the focus ring to sharpen the image.
DC-06 document camera
If you connect a digital camera or USB storage device, you can use the
projector’s Slideshow feature. See the Network and PC Free Operation Guide on
your projector CD.
Follow the on-screen instructions to install the Epson USB Display software.
(You need to install the software only the first time you connect.) Then press
the USB button on the remote control.
Network (LAN)
Connect the projector to your network using an Ethernet® cable. See
“Network Configuration” on the back of this sheet for more information.
For information on connecting an external monitor or external speakers, see
the User’s Guide on your projector CD.
Turn on your equipment
1
2
Turn the zoom ring to reduce or enlarge the image.
Turn on your computer or video source.
Plug in the projector.
Focus
Zoom
*411783500*
*411783500*
4
If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely.
5
If your image looks like
projector to correct it.
or
, press the
or
buttons on the
Control projector volume
Navigate
projector
menus
You can use the remote control to operate the projector. With the USB cable,
you can use the remote as a wireless mouse. For more information on using
the remote control, see your User’s Guide.
Network configuration
Project over the network
Troubleshooting
Where to get help
If you need to configure the projector for your network, you can use the
projector’s menu system.
Install EasyMP® Network Projection and Easy Management® EasyMP Monitor
(Windows only) on each computer that will project over the network. Use the
CD labeled Epson Projector Software for Meeting & Monitoring to install
these programs.
If you see a blank screen...
Manuals
1
Press the Menu button on the remote control, select the Network
menu, then press Enter.
1
Press the LAN button on the remote control.
If you see a blank screen or the No signal message after turning on your
computer, check the following:
•
•
Make sure the power light on the projector is green and not flashing, and
the A/V Mute slide is open.
Press the Source Search button on the projector or the remote control to
select the computer as the image source.
•If you’re using a Windows notebook, press the function key on your
2
3
4
Choose Network Configuration and press Enter.
Select the Wired LAN menu and press Enter.
2
Start EasyMP Network Projection on your computer.
Windows: Select Start > Programs or All Programs > EPSON Projector
> EasyMP Network Projection.
Mac OS® X: Double-click the EasyMP Network Projection icon in your
Applications folder.
Choose IP Settings and press Enter. You see a screen like the following:
3
Select Advanced Connection Mode, then click OK.
keyboard that lets you display on an external monitor. It may be labelled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it.
If the projector and notebook don’t display the
same image...
Windows
Try using the CRT/LCD or
key as described above. On most systems, this
key lets you toggle between the LCD screen and the projector, or display on
both at the same time.
If that doesn’t work, check your monitor settings to make sure both the LCD
screen and the external monitor port are enabled.
5 Do one of the following:
• If your network assigns addresses automatically, turn on the DHCP
setting.
•
If your network does not assign addresses automatically, turn off
DHCP and enter the projector’s IP Address, Subnet Mask, and
Gateway Address, as needed.
To enter numbers, use the arrow buttons on the remote control to
highlight a number, then press the Enter button. When you’re finished
entering an address, highlight Return, then press Enter.
6
To prevent the IP address from appearing on the network standby
screen, set the IP Address Display setting to Off.
7
When you’re done, select Complete and press Enter to save your
settings. Then press Enter again to confirm.
8
Press the Menu button to exit the menu system.
1
From the Windows Control Panel, open the Display utility. In Windows
Vista®, right-click on the desktop and select Personalize, then select
Display Settings.
2
Click Settings, then click Advanced or Advanced Settings.
For more information about using the projector, install the manuals from your
projector CD.
Telephone Support Services
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for
the duration of your warranty period. You may also speak with a projector
support specialist by dialing:
(562) 276-4394 (U.S.) or (905) 709-3839 (Canada), 6
Monday through Friday
AM
to 6
PM,
Pacific Time,
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
Visit epson.com/support for solutions to common problems. You can
download utilities and documentation, get FAQs and troubleshooting advice,
or e-mail Epson with your questions.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see your projector User’s Guide.
4
Select the projector you want to connect to, then click Connect.
If you don’t see the projector you want, click the Automatic search
button.
5
If you see a message asking for a keyword, enter the four digits that
appear on the LAN standby screen and click OK.
Your computer image is projected, with a floating toolbar:
When you’re done presenting, click Disconnect on the toolbar.
NOTE: For more information about using and monitoring the projector on
a network, see your Network and PC Free Operation Guide and EasyMP
Monitor Operation Guide (Windows only). These guides are installed
along with your projector User’s Guide and are viewable by clicking the
icons for them on your computer desktop.
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
3
The method for adjusting the setting varies; you may have to click a
Monitor tab, then make sure the external Monitor port is set as your
primary display and/or enabled.
Mac OS X
1
From the Apple® menu, select System Preferences, then select Display
or Displays.
2
3
4
Click Detect Displays.
Make sure the VGA Display or Color LCD dialog box is selected.
Click Arrangement or Arrange, then make sure Mirror Displays is
selected.
Epson, EasyMP, and Easy Management are registered trademarks, and Epson Exceed Your Vision is a
registered logomark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of
Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2009 Epson America, Inc. 8/09
Printed in XXXXXX
CPD-27666
Network configuration
Project over the network
Troubleshooting
Where to get help
If you need to configure the projector for your network, you can use the
projector’s menu system.
Install EasyMP® Network Projection and Easy Management® EasyMP Monitor
(Windows only) on each computer that will project over the network. Use the
CD labeled Epson Projector Software for Meeting & Monitoring to install
these programs.
If you see a blank screen...
Manuals
1
Press the Menu button on the remote control, select the Network
menu, then press Enter.
1
Press the LAN button on the remote control.
If you see a blank screen or the No signal message after turning on your
computer, check the following:
•
•
Make sure the power light on the projector is green and not flashing, and
the A/V Mute slide is open.
Press the Source Search button on the projector or the remote control to
select the computer as the image source.
•If you’re using a Windows notebook, press the function key on your
2
3
4
Choose Network Configuration and press Enter.
Select the Wired LAN menu and press Enter.
2
Start EasyMP Network Projection on your computer.
Windows: Select Start > Programs or All Programs > EPSON Projector
> EasyMP Network Projection.
Mac OS® X: Double-click the EasyMP Network Projection icon in your
Applications folder.
Choose IP Settings and press Enter. You see a screen like the following:
3
Select Advanced Connection Mode, then click OK.
keyboard that lets you display on an external monitor. It may be labelled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it.
If the projector and notebook don’t display the
same image...
Windows
Try using the CRT/LCD or
key as described above. On most systems, this
key lets you toggle between the LCD screen and the projector, or display on
both at the same time.
If that doesn’t work, check your monitor settings to make sure both the LCD
screen and the external monitor port are enabled.
5 Do one of the following:
• If your network assigns addresses automatically, turn on the DHCP
setting.
•
If your network does not assign addresses automatically, turn off
DHCP and enter the projector’s IP Address, Subnet Mask, and
Gateway Address, as needed.
To enter numbers, use the arrow buttons on the remote control to
highlight a number, then press the Enter button. When you’re finished
entering an address, highlight Return, then press Enter.
6
To prevent the IP address from appearing on the network standby
screen, set the IP Address Display setting to Off.
7
When you’re done, select Complete and press Enter to save your
settings. Then press Enter again to confirm.
8
Press the Menu button to exit the menu system.
1
From the Windows Control Panel, open the Display utility. In Windows
Vista®, right-click on the desktop and select Personalize, then select
Display Settings.
2
Click Settings, then click Advanced or Advanced Settings.
For more information about using the projector, install the manuals from your
projector CD.
Telephone Support Services
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for
the duration of your warranty period. You may also speak with a projector
support specialist by dialing:
(562) 276-4394 (U.S.) or (905) 709-3839 (Canada), 6
Monday through Friday
AM
to 6
PM,
Pacific Time,
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
Visit epson.com/support for solutions to common problems. You can
download utilities and documentation, get FAQs and troubleshooting advice,
or e-mail Epson with your questions.
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector or register online at
www.epson.com/webreg.
Optional accessories
For a list of optional accessories, see your projector User’s Guide.
4
Select the projector you want to connect to, then click Connect.
If you don’t see the projector you want, click the Automatic search
button.
5
If you see a message asking for a keyword, enter the four digits that
appear on the LAN standby screen and click OK.
Your computer image is projected, with a floating toolbar:
When you’re done presenting, click Disconnect on the toolbar.
NOTE: For more information about using and monitoring the projector on
a network, see your Network and PC Free Operation Guide and EasyMP
Monitor Operation Guide (Windows only). These guides are installed
along with your projector User’s Guide and are viewable by clicking the
icons for them on your computer desktop.
You can purchase screens, carrying cases, or other accessories from an Epson
authorized reseller. To find the nearest reseller, call 800-GO-EPSON
(800-463-7766). Or you can purchase online at www.epsonstore.com (U.S.
sales) or www.epson.ca (Canadian sales).
3
The method for adjusting the setting varies; you may have to click a
Monitor tab, then make sure the external Monitor port is set as your
primary display and/or enabled.
Mac OS X
1
From the Apple® menu, select System Preferences, then select Display
or Displays.
2
3
4
Click Detect Displays.
Make sure the VGA Display or Color LCD dialog box is selected.
Click Arrangement or Arrange, then make sure Mirror Displays is
selected.
Epson, EasyMP, and Easy Management are registered trademarks, and Epson Exceed Your Vision is a
registered logomark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of
Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks
of their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2009 Epson America, Inc. 8/09
Printed in XXXXXX
CPD-27666