Samsung SP-350 Product specifications

Downloaded From projector-manual.com Samsung Manuals
To avoid injuries or damage to property, please read the following precautions carefully and use the
product accordingly.
Failure to follow the instructions marked with this symbol may cause personal injury or even fatality.
Failure to follow the instructions marked with this symbol may cause personal injury or damage to the
product or property.
| Power Related | Installation Related | Cleaning and Use Related |
[The images here are for reference only, and are not applicable in all cases (or countries).]
Insert the power plug firmly so that it does not come loose.
z
When the connection is not firm, it may cause a fire.
Do not use loose power outlets or damaged power cables.
z
There is a danger of electric shock or fire.
Under no circumstances touch the power plug with wet hands.
z
There is a danger of electric shock.
Do not plug multiple devices into a single wall outlet.
z
There is a danger of fire.
Do not bend the power cord excessively or place heavy objects on it.
z
There is a danger of electric shock or fire.
Before moving the product, make sure the power is off and remove
the power cord from the wall outlet. In addition, make sure all
connection cables are disconnected from other devices before
moving it.
z
Moving the product without disconnecting the power cord may damage the
power cord and cause electric shock or fire.
To disconnect the apparatus from the mains, the plug must be pulled
Downloaded From projector-manual.com Samsung Manuals
out from the mains socket, therefore the mains plug shall be readily
operable.
z
There is a danger of electric shock or fire.
Always unplug the unit by holding the power plug. Pulling the power
cable may damage the inside of it.
z
There is a danger of fire.
Unplug the power plug before cleaning the product.
z
There is a danger of electric shock or fire.
| Power Related | Installation Related | Cleaning and Use Related |
TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN
FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.
z
There is a danger of fire.
When installing the product in a cabinet or on a shelf, make sure the
front end of the base does not protrude.
z
Dropping the product may damage it or cause injury.
Keep the power cord away from heaters.
z
The coating of the power cord may melt and cause electric shock or fire.
Do not install the product in locations exposed to oil, smoke,
moisture or water (rainwater), or in a vehicle.
z
There is a danger of electric shock or fire.
Do not install the product in locations with poor ventilation such as a
bookshelf, closet, etc.
z
An increase in the internal temperature may cause a fire.
Downloaded From projector-manual.com Samsung Manuals
Do not install on an unstable location, or on a stand smaller than the
product.
z
If the product falls it may harm children. Install on a flat and stable location as
the front part is heavy.
In case of thunder/lightning, disconnect the power cord from the
wall outlet.
z
There is a danger of electric shock or fire.
Make sure the product's vents are not blocked by a table cloth or
curtain.
z
An increase in the internal temperature may cause a fire.
Place the product on the ground carefully.
z
Doing so may cause damage or injury.
Do not drop the product while carrying it.
z
Doing so may cause damage or injury.
Keep the product out of children’s reach.
z
If the product falls it may cause harm to children. Install on a flat and stable
location as the front part is heavy.
| Power Related | Installation Related | Cleaning and Use Related |
Do not insert any metal objects such as a fork, chopsticks, wires,
or inflammable objects such as paper into the vents, the
PC/COMPOSITE port, the Power port or the Battery port.
z
This may cause electric shock or fire.
If water or an alien substance enters the product, turn the product off,
Downloaded From projector-manual.com Samsung Manuals
disconnect the power cord from a wall outlet and contact a Service Center.
Do not disassemble, or attempt to fix or modify the product.
z
When the product requires repairs, contact a Service Center.
Do not use or keep the product near flammable sprays or other such
substances.
z
There is a danger of fire or explosion.
Do not place containers with water, vases, drinks, chemicals, small
metal parts or heavy objects on the product.
z
If water enters the product, it may cause electric shock, or fire and when heavy
objects fall, they may cause injury.
Do not let children place objects such as toys or cookies on the
product.
z
If a child tries to reach for any of these objects, the product may fall and cause
harm.
Do not look directly at the light of the lamp nor project the picture
onto eyes.
z
This is dangerous; especially for children.
When you remove batteries from the remote, be careful that they are
not swallowed by children. Keep batteries out of the reach of
children.
z
If swallowed, see a doctor immediately.
If the product emits smoke, unusual noise, or there is a burning
smell,disconnect the power plug immediately, and contact a Service
Center.
z
There is a danger of electric shock or fire.
If the power plug pin or jack is exposed to dust, water or alien
substances, clean it thoroughly.
z
There is a danger of electric shock or fire.
When cleaning the product, disconnect the power cord and wipe the
Downloaded From projector-manual.com Samsung Manuals
product using a soft dry cloth.
z
Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide,
air freshener, lubricant or detergent.
When not using the product for an extended period of time,
disconnect the power plug.
z
Otherwise, this may cause heat emission from the accumulated dirt or degraded
insulation, leading to electric shock or fire.
Do not install the product in places with heavy dust, chemical
substances, high or low temperatures, high humidity, or where it will
be operated for a long period continuously etc.
If the product is dropped or the casing is damaged, turn the product
off and unplug the power cord.
z
This may cause electric shock or fire. Contact a Service Center.
Use only specified standard batteries. Do not use new and used
batteries together.
z
Incorrect polarity may cause a battery to break or leak and could lead to fire,
injury, or contamination (damage).
Make sure to place your remote control on a table or desk.
z
If you step on the remote control, you may fall and hurt yourself or the product
may be damaged.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with separate
collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with
other household waste at the end of its working life. To prevent possible harm to the environment
or damage to health from uncontrolled waste disposal, please separate this from other types of
waste and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
local government office, for details of where and how they can take this item for environmentally
safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product should not be mixed with other commercial wastes for disposal.
Downloaded From projector-manual.com Samsung Manuals
Correct disposal of batteries in this product - Europe only
(Applicable in the European Union and other European countries with separate battery
return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product
should not be disposed of with other household waste at the end of their working life. Where
marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium
or lead above the reference levels in EC Directive 2006/66. If batteries are not properly disposed
of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other
types of waste and recycle them through your local, free battery return system.
Downloaded From projector-manual.com Samsung Manuals
| Product Features | Product Views | Remote Control | Product Specifications |
An optical engine adopting new LCD technology
- 1024 x 768 panel has been adapted.
- Utilizes a 3P-LCD panel.
- SP-L330: Provides a bright screen of 3300 lumen.
SP-L350: Provides a bright screen of 3500 lumen.
- Compact size, lightweight, and good portability
Minimized fan noise
- Minimizes the noise generated by the product’s fan by optimizing the internal air flow and fan
installation structure.
Various input terminals
- Increases the connectivity to peripherals by providing various terminals, such as HDMI (DVI PC signal,
supported), 2 D-Sub 15p, S-Video, and Video terminals.
Audio Output
- There are two speakers and a 5-band equalizer.
User adjustments
- This unit allows adjustment of each input port.
- The unit has a reference pattern that can be used for positioning and adjustment.
| Product Features | Product Views | Remote Control | Product Specifications |
Front/Upper Side
Downloaded From projector-manual.com Samsung Manuals
1. Indicators
5. POWER(
- STAND BY (Blue LED)
) Button
Used to turn the projector on or off.
- LAMP (Blue LED)
- TEMP (Red LED)
6. Lens
※ Refer to the LED Indications.
7. Remote Control Signal Receiver
2. VOL - / + & Select and Move Button
Adjusts the volume.
8. Focus Ring
Use this button to move to or select an item within a
Used for Focus Adjustment.
menu.
9. Zoom Knob
3. MENU Button
Used to enlarge or reduce image size.
Use this button to enter or exit a menu or to move
forward in a menu.
10.Lens cover
4. SOURCE Button
Used to select input signals from the external
sources.
Unpacking
Quick Installation Guide
Warranty Card/ Registration Card
(Not available in all locations)
Downloaded From projector-manual.com Samsung Manuals
User Manual CD
Remote Control/ 1 Batteries (CR2025)
Power Cable
Cleaning Cloth
(Not available in all locations)
D-Sub Cable
LED Indications
:Light is On
STAND
BY
:Light is Blinking
LAMP
TEMP
○
○
Information
If you press the POWER button on the remote control or projector, the screen
appears within 30 seconds.
The projector is in normal operating condition.
○
This state appears when the projector is preparing an operation after the POWER button on
○
the projector or the remote control has been pressed.
The POWER button is pressed to turn off the projector, and the cooling system is in
○
○
:Light is Off
operation to cool off the inside of the projector. (Operates for about 30 seconds.)
Refer to Action 1 below if the cooling fan inside the projector is not in normal operation
○
condition.
Refer to Action 2 below if the lamp cover protecting the lamp unit is not closed properly.
○
This indicates that the lens cover does not open completely. Refer to Action 3 below.
This indicates that it has changed to Cooling mode, because the internal temperature of the
projector has increased beyond the maintenance limit.
Refer to Action 4 below.
○
This indicates that the power is turned off automatically because the internal temperature of
○
the projector has increased beyond the operation limit. Refer to Action 5 below
A problem has occurred with the operation of the lamp. Refer to Action 6.
The lifetime of the lamp has expired. Refer to Action 7.
The power for the product is not operating normally. Contact a service center.
Clearing Indicator Problems
Classification
Action 1
State
Measures
When the cooling fan
If the symptom remains even after disconnecting and then reconnecting
system is not in normal
the power cord and turning the projector on again, contact your product
operating condition.
provider or our service center.
When the lamp cover
Action 2
protecting the lamp unit is
Check if the screws on the side of the projector are securely tightened. If
not properly closed or the
they are and the indicators are still lit, contact your product distributor or
sensor system is not in
a service center.
normal operating condition.
Action 3
The lens cover is not open
completely.
Open the lens cover completely.
If the lens cover is not open completely while operating the projector,
both the video and audio are turned off automatically.
If the lens cover remains not completely open for ten minutes, the
Downloaded From projector-manual.com Samsung Manuals
projector is turned off automatically.
If the internal temperature of the projector has increased beyond the
operation limit, it is changed to Cooling mode before it is turned off
This indicates that the projector
has changed to Cooling mode,
Action 4
because the internal temperature
of the projector has increased
beyond the operation limit.
automatically.
* Cooling mode: The fan speed has increased and the lamp of the
projector has been changed automatically to ECO mode.
Check whether the ventilating hole of the projector is blocked.
Check whether the air filter is blocked. Clean it if it is blocked.
Check whether the surrounding temperature of the projector is higher
than the standard temperature range of the projector.
Cool the projector sufficiently and operate it again.
Check whether the ventilating hole of the projector is blocked.
If the internal temperature of the
Action 5
projector increases higher than
the limit, it is turned off
automatically.
Check whether the air filter is blocked. Clean it if it is blocked.
Check whether the surrounding temperature of the projector is higher
than the standard temperature range of the projector.
Cool the projector sufficiently and operate it again.
If the same problem occurs continually, contact your product distributor or
service center.
The lamp
malfunctions after power
Action 6
turns off
abnormally or after
powering on right after
Turn the power off, wait for a sufficient amount of cooling time and then
turn the power on to operate. If the same problem occurs continually,
contact your product distributor or service center.
turning off the projector.
Action 7
When the screen becomes darker
Check the lamp usage time on the Information Display screen. If you need
to replace the lamp, contact your product distributor or service center.
This Projector uses a cooling fan system to keep the unit from overheating. Operation of the cooling fan
may cause noise, which does not affect the product performance and is part of normal operation.
Rear Side
1. PC OUT port
7. [AV IN] VIDEO Input port
2. AUDIO OUT port
8. [AV IN] S-VIDEO Input port
Downloaded From projector-manual.com Samsung Manuals
3. HDMI/DVI IN Input port
9. PC IN 1,2 Input port
4. PC 1/DVI AUDIO IN Input port
10.[PC IN2] AUDIO Input port
5. RS-232C port (For service only)
11.Remote Control Signal Receiver
6. [AV IN] R-AUDIO-L Input port
12.POWER Input port
| Product Features | Product Views | Remote Control | Product Specifications |
1.
POWER (
2.
AUTO Button
3.
MENU (
4.
Move (▲ ▼ ◀ ▶)/(
5.
V.KEYSTONE(+/-)
) Button
) Button
) Buttons
(VERTICAL KEYSTONE)Button
6.
INSTALL Button
7.
BLANK Button
8.
P.SIZE Button
9.
QUICK Button
10. MUTE (
) Button
11. RETURN (
12. EXIT (
) Button
) Button
13. VOL Button
14. INFO Button
15. SOURCE Button
16. P.MODE Button
17. STILL Button
1. POWER (
)
Used to turn on the projector.
2. AUTO
Adjusts the Picture automatically. (Available in PC Mode Only)
3. MENU (
)
Used to display the Menu Screen.
4. Move (▲ ▼ ◀ ▶)/ (
)
Used to move to or select each menu item.
5. V.KEYSTONE(VERTICAL KEYSTONE) (+/-)
Use this when video scenes are distorted or tilted.
6. INSTALL
Downloaded From projector-manual.com Samsung Manuals
Used to flip or reverse the projected image.
7. BLANK
This is used to turn off the video and audio temporarily.
It is released when any button other than the POWER button is pressed.
8. P.SIZE
Used to adjust the size of picture screen.
9. QUICK
This is used when quickly selecting the last used menu.
10. MUTE (
)
This is used to temporarily mute the sound.
To hear sound again, press the MUTE button again or press the - VOL + button.
11. RETURN (
)
Returns to the previous menu.
12. EXIT (
)
Used to make the Menu Screen disappear.
13. VOL
Adjusts the volume.
14. INFO
Used to check source signals, picture setup, PC screen adjustment and lamp lifespan.
15. SOURCE
This is used to switch between the TV and the external input.
16. P.MODE
Used to select Picture Mode.
17. STILL
Used to see still images.
| Product Features | Product Views | Remote Control | Product Specifications |
Design and specifications of the product may be modified without prior notice for better performance.
Specifications
Model
SP-L330 / SP-L350
Panel
0.63" 3LCD w/MLA
Resolution
XGA (1024 x 768)
Aspect ratio
4:3
Brightness
SP-L330:Max 3,300 ANSI lumen (Eco 2200 lumen)
SP-L350:Max 3,500 ANSI lumen (Eco 2200 lumen)
Contrast
Max 400:1
Diagonal screen size
40 ~ 300"
Projection Range
1 m ~ 10 m (3.2 ft ~ 32.8 ft)
Zoom Adjustment
Manual
Focus Adjustment
Manual
Lens
F=1.65~1.93(0.06~0.07 inch), f=18.5mm~22.5 mm
Zoom Ratio
1:1.2
Keystone
Vertical (±30°), horizontal (±30°)
Downloaded From projector-manual.com Samsung Manuals
Power
220W (Normal : 200W, Eco : 152W )
Consumption
Lamp
Input Terminal
Life Time
2,000 Hours (Eco : 2,500 Hours )
D-Sub 15p x 2
Analog RGB, analog YPbPr
HDMI
Digital RGB, digital YCbCr
Mini DIN x 1
S-Video
RCA x 1
Composite video
Speaker
3W x 2 (Stereo)
Power
Max 300 W
Consumption
Power
Voltage
100~240V AC, 50/60Hz
Noise
Eco : 30dB, Normal : 32dB, Bright : 35dB
291(W) x 289(D) x 127(H)
Dimensions
11.5 inches(W) x 11.4 inches(D) x 5 inches(H)
Weight
3.9 Kg / 8.6 lb
Temperature : 41 °F ~ 95 °F (5 °C ~ 35 °C),
Operating
User
Environment
Humidity : 20 % ~ 80 % ((Non-condensing))
Temperature : -14 °F ~ 140 °F (-10 °C ~ 60 °C)
Storage
Humidity : 10 % ~ 90 % (Non-condensing)
This Class B equipment is designed for home and office use. The equipment has been registered
regarding EMI for residential use. It may be used in all areas. Class A is for office use. Class A is for
business while class B emits less electromagnetic waves than class A.
The LCD panel used in the LCD projector consists of hundreds of thousands of fine pixels.
Like other video display devices, the LCD panel may contain bad pixels which do not operate. When
shipping a product, the conditions for identifying bad pixels and the number of bad pixels that a LCD
panel is allowed to contain are strictly managed in accordance with the relevant specified standards
by the LCD panel manufacturer and our company. Though a screen may have some dead pixels, this
does not affect the overall screen quality and the lifetime of the product.
Supported Display Modes
PC Timing (D-Sub/HDMI)
Format
Resolution
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Frequency
(MHz)
IBM
640 x 350
70Hz
31.469
70.086
25.175
IBM
640 x 480
60Hz
31.469
59.940
25.175
IBM
720 x 400
70Hz
31.469
70.087
28.322
VESA
640 x 480
60Hz
31.469
59.940
25.175
MAC
640 x 480
67Hz
35.000
66.667
30.240
VESA
640 x 480
70Hz
35.000
70.000
28.560
VESA
640 x 480
72Hz
37.861
72.809
31.500
VESA
640 x 480
75Hz
37.500
75.000
31.500
VESA
720 x 576
60Hz
35.910
59.950
32.750
VESA
800 x 600
56Hz
35.156
56.250
36.000
VESA
800 x 600
60Hz
37.879
60.317
40.000
VESA
800 x 600
70Hz
43.750
70.000
45.500
VESA
800 x 600
72Hz
48.077
72.188
50.000
VESA
800 x 600
75Hz
46.875
75.000
49.500
MAC
832 x 624
75Hz
49.726
74.551
57.284
VESA
1024 x 768
60Hz
48.363
60.004
65.000
VESA
1024 x 768
70Hz
56.476
70.069
75.000
VESA
1024 x 768
72Hz
57.672
72.000
78.434
VESA
1024 x 768
75Hz
60.023
75.029
78.750
VESA
1152 x 864
60Hz
53.783
59.959
81.750
VESA
1152 x 864
70Hz
63.000
70.000
96.768
VESA
1152 x 864
72Hz
64.872
72.000
99.643
VESA
1152 x 864
75Hz
67.500
75.000
108.000
VESA
1280 x 720
60Hz
44.772
59.855
74.500
Downloaded From projector-manual.com Samsung Manuals
VESA
1280 x 720
70Hz
52.500
70.000
89.040
VESA
1280 x 720
72Hz
54.072
72.000
91.706
VESA
1280 x 720
75Hz
56.456
74.777
95.750
VESA
1280 x 768
60Hz
47.776
59.870
79.500
VESA
1280 x 768
75Hz
60.289
74.893
102.250
VESA
1280 x 800
60Hz
49.702
59.810
83.500
VESA
1280 x 800
75Hz
62.795
74.934
106.500
VESA
1280 x 960
60Hz
60.000
60.000
108.000
VESA
1280 x 960
70Hz
69.930
70.000
120.839
VESA
1280 x 960
72Hz
72.072
72.000
124.540
VESA
1280 x 960
75Hz
75.231
74.857
130.000
VESA
1280 x 1024
60Hz
63.981
60.020
108.000
VESA
1280 x 1024
70Hz
74.620
70.000
128.943
VESA
1280 x 1024
72Hz
76.824
72.000
132.752
VESA
1280 x 1024
75Hz
79.976
75.025
135.000
VESA
1400 x 1050
60Hz
65.317
59.978
121.750
VESA
1440 x 900
60Hz
55.935
59.887
106.500
VESA
1440 x 900
75Hz
70.635
74.984
136.750
VESA
1600 x 1200
60Hz
75.000
60.000
162.000
For the resolutions presented above, if a signal with a resolution lower or higher than 1024x768 is
input, it is converted to 1024x768 by the Scaler chip inside the projector.
When the real resolution (1024x768) of the projector and the PC output resolution are the same, the
screen quality is optimal.
AV Timing (D-Sub)
Format
Resolution
Scan
BT.601 SMPTE 267M
480i
59.94Hz
Interlaced
BT.1358 SMPTE 293M
480p
59.94Hz
Progressive
BT.601
576i
50Hz
Interlaced
BT.1358
576p
50Hz
Progressive
720p
59.94Hz/60Hz
Progressive
720p
50Hz
Progressive
1080i
59.94Hz/60Hz
Interlaced
1080i
50Hz
Interlaced
SMPTE 296M
BT.709 SMPTE 274M
AV Timing (HDMI)
Format
Resolution
Scan
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Frequency
(MHz)
EIA-861
Format1
640 x 480
Progressive
59.940
31.469
25.175
EIA-861
Format1
640 x 480
Progressive
60.000
31.500
25.200
EIA-861
Format2,3
720 x 480
Progressive
59.940
31.469
27.000
EIA-861
Format2,3
720 x 480
Progressive
60.000
31.500
27.027
EIA-861
Format4
1280 x 720
Progressive
59.939
44.955
74.175
EIA-861
Format4
1280 x 720
Progressive
60.000
45.000
74.250
EIA-861
Format5
1920 x 1080
Interlaced
59.939
33.716
74.175
EIA-861
Format5
1920 x 1080
Interlaced
60.000
33.750
74.250
EIA-861
Format17,18
720 x 576
Progressive
50.000
31.250
27.000
EIA-861
Format19
1280 x 720
Progressive
50.000
37.500
74.250
EIA-861
Format20
1920 x 1080
Interlaced
50.000
28.125
74.250
AV Timing (VIDEO/S-VIDEO)
NTSC, NTSC 4.43, PAL, PAL60, PAL-N, PAL-M, SECAM
Downloaded From projector-manual.com Samsung Manuals
Downloaded From projector-manual.com Samsung Manuals
| Basic Settings | Connecting the Power | Connecting an External Device |
Installing the Projector
Install the projector so that the beam from the projector is perpendicular to the screen.
Place the projector so that the lens is at the center of the screen.
If the screen is not vertically installed, the picture on the screen may not be a rectangle.
Do not install the screen in bright surroundings. If the screen is too bright, the picture on the screen will not be displayed
clearly.
When installing the screen in bright surroundings, use curtains.
You can install the projector in the following locations: Front-Floor / Front-Ceiling / Rear-Floor / Rear-Ceiling.
(To view the installation position settings)
To view the picture when installing the projector behind the screen,
Install a semi-transparent screen.
Select Menu > Setup > Install > Rear-Floor
To view the picture when installing the projector in the front of the screen,
Install the projector at the side where you are watching the
screen.
Select Menu > Setup > Install > Front-Floor
Zoom and Focus Adjustment
Zoom Knob
Focus Ring
Downloaded From projector-manual.com Samsung Manuals
You can adjust the size of image within zoom range by manipulating the Zoom
Knob.
Focus the picture on the screen using the Focus Ring.
If your product is installed at a location out of the specified projection distance
(refer to Screen Size and Projection Distance), the focus cannot be
adjusted correctly.
Leveling with Adjustable Feet
For level placing of the projector, adjust the Adjustable Feet.
The projector can be adjusted to a height of up to 30 mm (about 12 °) from the reference
point.
Depending on the position of the projector, Keystone distortion of image may appear.
If a keystone occurs, adjust it using the V-Keystone function.
Screen Size and Projection Distance
Install the projector on a flat, even surface and level the projector using the adjustable feet to realize optimal picture quality. If images
are not clear, adjust them using the Zoom Knob or Focus Ring, or move the projector forward and backward.
Screen size
Horizental
Vertical
Max
Min
Offset
(M:inch)
(X:mm)
(Y:mm)
(Z:mm)
(Z:mm)
(Y':mm)
40
812.8
609.6
1376
1140
102
50
1016.0
762.0
1727
1433
127
60
1219.2
914.4
2078
1726
152
70
1422.4
1066.8
2430
2020
178
80
1625.6
1219.2
2781
2313
203
90
1828.8
1371.6
3133
2606
229
100
2032.0
1524.0
3484
2899
254
110
2235.2
1676.4
3835
3192
279
120
2438.4
1828.8
4187
3485
305
130
2641.6
1981.2
4538
3778
330
140
2844.8
2133.6
4889
4071
356
150
3048.0
2286.0
5241
4364
381
160
3251.2
2438.4
5592
4657
406
170
3454.4
2590.8
5944
4950
432
180
3657.6
2743.2
6295
5243
457
190
3860.8
2895.6
6646
5536
483
200
4064.0
3048.0
6998
5829
508
210
4267.2
3200.4
7349
6122
533
220
4470.4
3352.8
7701
6415
559
230
4673.6
3505.2
8052
6708
584
240
4876.8
3657.6
8403
7001
610
250
5080.0
3810.0
8755
7294
635
Downloaded From projector-manual.com Samsung Manuals
260
5283.2
3962.4
9106
7587
660
270
5486.4
4114.8
9457
7880
686
280
5689.6
4267.2
9809
8173
711
290
5892.8
4419.6
10160
8466
737
300
6096.0
4572.0
10512
8759
762
This projector is designed to show images optimally on a 80 ~ 120 inch sized screen.
A. Screen
Z: Projection distance
Y': Distance from Lens Center to Image Bottom
Adjusting the H-Keystone
1. Check the projection distance according to the screen size and then install the projector (see the table below).
Screen size (m)
Projection
Projection
distance
distance
Diagonal
Width
Length
(m)
(ft)
1
0.8
0.6
1.4
4.5
1.3
1
0.8
1.7
5.5
1.5
1.2
0.9
2.1
6.8
1.8
1.4
1.1
2.4
7.8
2
1.6
1.2
2.8
9.1
2.3
1.8
1.4
3.1
10.1
2.5
2
1.5
3.4
11.1
2.8
2.2
1.7
3.8
12.4
3
2.4
1.8
4.1
13.4
3.3
2.6
2
4.5
14.7
3.6
2.8
2.1
4.8
15.7
3.8
3
2.3
5.1
16.7
4.1
3.3
2.4
5.5
18.0
4.3
3.5
2.6
5.8
19.0
4.6
3.7
2.7
6.2
20.3
4.8
3.9
2.9
6.5
21.3
5.1
4.1
3
6.8
22.3
5.3
4.3
3.2
7.2
23.6
5.6
4.5
3.4
7.5
24.6
5.8
4.7
3.5
7.9
25.9
6.1
4.9
3.7
8.2
26.9
6.4
5.1
3.8
8.5
27.8
6.6
5.3
4
8.9
29.1
Downloaded From projector-manual.com Samsung Manuals
A : Projector
B : Projection distance
C : Screen
- Projection distance: Vertical distance from a
projected picture
6.9
5.5
4.1
9.2
30.1
7.1
5.7
4.3
9.6
31.4
7.4
5.9
4.4
9.9
32.4
7.6
6.1
4.6
10.2
33.4
2. Select one from Front-Floor, Front-Ceiling, Rear-Floor and Rear-Ceiling according to the location to install the projector.
3. Set the values of the H-Keystone and the V-Keystone to '0' and place the zoom knob right in the middle of its movement range.
4. Press the MENU button to display the Crosshatch screen of the Test Pattern.
(Setup → Test Pattern → Crosshatch)
5. Adjust the location of the projector until lines ① and ② in the picture below become parallel.
Screen
Crosshatch Test Pattern
① A virtual vertical line made on the screen using a piece
② A vertical line in the middle of the Test Pattern
of thread, etc.
6. Adjust the projector's angle so that a corner of the projected picture (which is nearest to the projector) meets that of the screen.
A : Projector
B : Screen
C : Projected image
D : A corner of the picture nearest to
the projector
→
Adjust the projector's angle until the projected image covers the entire screen area
(The projected image may not cover the entire screen area depending on the projector's installation height. In this case, adjust the
projector's angle so that the entire screen area can be covered.)
7. Press the V.KEY-STONE button on the remote control. The V-Keystone menu will be displayed.
Adjust V-Keystone using the + or - button on the remote control.
- A : Projector
- B : Screen
- C : Projected image
Downloaded From projector-manual.com Samsung Manuals
→
Keep adjusting until the vertical line on the Test
Pattern becomes parallel with the outer vertical line on
the screen.
8. Press the ▲ or ▼ button to select H-Keystone.
Adjust H-Keystone using the + or - button on the remote control.
- A : Projector
- B : Screen
- C : Projected image
Keep adjusting until the horizontal line on the Test
Pattern becomes parallel with the outer horizontal line
on the screen.
→
9. Adjust the screen size using the zoom knob.
10. If any part of the projected image is larger than the screen, adjust the size of the projected image using the Custom option in the
Size menu.
How to adjust:
1. Press the MENU button.
2. Select Picture to move on to the Size menu.
3. Select the Custom option and then select an area to adjust.
4. Adjust the screen size using the ▲ or ▼ button.
- A : Projector
- B : Screen
- C : Projected image
→
Keystone, which is a feature to calibrate an image skew, may degrade the brightness and resolution once it is
activated.
Setting up the PC Environment - Check the following items before connecting your PC to your projector.
1.
Click the right mouse button on the Windows desktop
and click on [Properties].
Downloaded From projector-manual.com Samsung Manuals
<Display Properties> tab will appear.
2.
Click on [Settings] tab and set the <Screen resolution> by
referring to <Resolution> described in the display mode table
supported by this projector.
You do not have to change <Color quality> setup.
3.
Press the [Advanced] button.
Another property window will appear.
4.
Click on [Monitor] tab and set the <Screen refresh rate> by referring
to <Vertical Frequency> described in the Supported
Resolution/Size Modes table.
5.
Click the [OK] button to close the window, and click the
[OK] button of the <Display Properties> window to close the
window.
The computer may restart automatically.
6.
Shut down the PC and connect to the projector.
Process might vary depending on your type of computer or Windows versions.
(For example, [Properties] appears instead of [Properties (R)] as shown in 1.)
This unit appliance supports up to 24 bits per pixel in Color quality when it is used as a PC monitor.
Projected images may differ from the monitor depending on monitor manufacturer or Windows versions.
When connecting the projector to a PC, check that PC setup complies to display settings supported by this projector. If not,
there may be signal problems.
Downloaded From projector-manual.com Samsung Manuals
| Basic Settings | Connecting the Power | Connecting an External Device |
1. Rear of Projector
Plug the power cord into the power terminal on the rear of the projector.
| Basic Settings | Connecting the Power | Connecting an External Device |
Connecting a PC using the D-Sub cable
Check that your PC and projector are turned off.
Connect the [PC IN (1 or 2)] terminal at the back of the projector to the D-Sub terminal of your PC using the D-Sub cable.
- For the supported input signals, refer to "PC Timing(D-Sub/HDMI)".
Connect the [PC 1/DVI AUDIO IN] or [AUDIO IN 2] terminal at the back of the projector to the Audio out terminal of your PC
using an audio cable (Not supplied).
Connecting a PC using an HDMI/DVI cable
Downloaded From projector-manual.com Samsung Manuals
Check that your PC and projector are turned off.
Connect the [HDMI/DVI IN] terminal of the projector to the HDMI or DVI terminal of your PC using a HDMI/HDMI or HDMI/DVI
cable (Not supplied).
- When connecting to the HDMI terminal of your PC, use an HDMI cable (Not supplied).
- For the supported input signals, refer to "PC Timing(D-Sub/HDMI)".
Connect the [PC 1/DVI AUDIO IN] terminal of the projector and the Audio out terminal of your PC using an audio cable (Not
supplied).
- If connecting with an HDMI/HDMI cable, an audio cable (Not supplied) is not needed.
Connecting an External Monitor
You can view an image on both your projector and a separate monitor at the same time.
Check that your PC and projector are turned off.
Downloaded From projector-manual.com Samsung Manuals
Connect the [PC IN 1] terminal at the back of the projector to the D-Sub terminal of your PC using a D-Sub cable.
Connect the [PC OUT] terminal of the projector to the D-Sub terminal of a monitor using a D-Sub cable.
- When connecting a monitor using the [PC OUT] function, make sure to connect your PC to the [PC IN 1] terminal.
- The monitor output which is connected to the [PC OUT] termininal will be normal even if you see a blank screen on
your projector.
- The [PC OUT] function also operates in standby mode.
Connecting an HDMI-Compatible Device
First, check that the AV device and your projector are turned off.
Connect the [HDMI/DVI IN] terminal at the back of the projector to the HDMI or HDMI/DVI output terminal of the digital output
device using an HDMI/DVI cable.
- When connecting to the HDMI output terminal of the digital output device, use an HDMI cable.
- For the supported input signals, refer to "AV Timing(HDMI)".
Connect the [PC 1/DVI AUDIO IN] terminal of the projector to the Audio out terminal of your digital output device using an audio
cable (Not supplied).
- If connecting with an HDMI/HDMI cable, an audio cable (Not supplied) is not needed.
Connecting an AV device using a D-Sub cable
Downloaded From projector-manual.com Samsung Manuals
First, check that the AV device and your projector are turned off.
Connect the [PC IN (1 or 2)] terminal at the back of the projector to the D-Sub terminal of your AV device using a D-Sub cable.
- For supported input signals, refer to the "AV Timing (D-Sub)".
Connect the [PC 1/DVI AUDIO IN] or [AUDIO IN 2] terminal at the back of the projector to the Audio out terminal of your AV
device using an audio cable (Not supplied).
Connecting a component output AV device
First, check that the AV device and your projector are turned off.
Connect the [PC IN (1 or 2)] terminal at the back of the projector to the Component terminal of your AV device using a DSub/Component cable (Not supplied).
- For supported input signals, refer to the "AV Timing(D-Sub)".
Connect the [PC 1/DVI AUDIO IN] or [AUDIO IN 2] terminal at the back of the projector and the Audio out terminal of your AV
device using an audio cable (Not supplied).
Connecting using a Video/S-Video cable
Downloaded From projector-manual.com Samsung Manuals
First, check that the AV device and your projector are turned off.
Connect the [VIDEO] or [S-VIDEO] terminal and the AV device using a Video cable (Not supplied) or S-Video cable (Not supplied).
- For supported input signals, refer to the "AV Timing(VIDEO/S-VIDEO)".
Connect the [AV IN R-AUDIO-L] terminal at the back of the projector and the Audio out terminal of your AV device using an audio
cable (Not supplied).
Connecting an External Speaker
You can hear sound through an external speaker instead of the internal speakers embedded in the projector.
Prepare an audio cable (Not supplied) suitable for your external speaker.
Connect the [AUDIO OUT] terminal of the projector to the external speaker using an audio cable.
- When using an external speaker, the internal speaker does not operate but you can adjust the volume of the external speaker
using the Volume button of the projector (or remote control).
- The [AUDIO OUT] terminal can output all audio signals.
Downloaded From projector-manual.com Samsung Manuals
Downloaded From projector-manual.com Samsung Manuals
|
Basic Functions
| Input | Picture | Setup | Option |
Turning on the projector
Check that the lens cover is opened completely.
Turn the power on.
Check that the STAND BY LED indicator is turned on.
Press the Power button. While the power is turned on (with the Power button on the remote control or at the
top of the projector), the blue LAMP LED indicator blinks.
When the power is turned on completely, the LAMP LED indicator remains blue.
If the projector is turned on when the lamp is not sufficiently cooled, fan noise may be heard because
the fan speed increases to cool the lamp.
Turning off the projector
Press the Power button. (Remote control or on top of the projector) OK or Cancel is displayed.
Select OK using the arrow keys (Remote control or on top of the projector).
Press the Enter button or press the Power button again.
The STAND BY LED indicator is turned off and the LAMP LED indicator blinks.
The fan speed increases to cool the lamp quickly. When the operation is finished,
the LAMP LED indicator is turned off and the STAND BY LED indicator is turned on and remains blue.
Remove the power cord.
Close the lens cover.
Selecting an input source
Press the SOURCE button (on the remote control or at the top of the projector).
AV, S-Video and HDMI modes can only be selected when an external device is connected, and the PC1
and PC2 modes can be selected regardless of whether an external device is connected or not.
|
Downloaded From projector-manual.com Samsung Manuals
Basic Functions
| Input | Picture | Setup | Option |
* Click the Play(
Screen
) button in the table below to view the video file.
Description
Adjustment
Source List
)/Stop(
Play/Stop
You can select a device connected to the projector to display.
1) PC 1
4) S-Video
2) PC 2
5) HDMI
3) AV
Edit Name
You can edit the names of devices connected to the projector.
1) VCR
7) DVD Receiver
2) DVD
8) Game
3) Cable STB
9) Camcorder
4) HD STB
10) DVD Combo
5) Satellite STB
11) PC
6) AV Receiver
|
* Click the Play(
Screen
)/Stop(
| Input | Picture | Setup | Option |
) button in the table below to view the video file.
Description
Adjustment
Mode
Basic Functions
Play/Stop
Select a screen state which is customized to your projector or change the screen mode as
required.
1) Mode
- Standard
This picture mode is the most general mode for various cases.
- Presentation
This mode is suitable for presentations.
- Text
This mode is suitable for text work.
- Movie
This mode is suitable for viewing a movie.
- Game
This picture mode is optimized for playing games.
▶The text in a still picture may be displayed picture is distorted.
Downloaded From projector-manual.com Samsung Manuals
Mode
- User
This mode is a customized mode created using the Mode > Save function.
▶ Presentation and Text modes are only enabled if the input signal is a PC
Timing(D-Sub/HDMI)signal.
2) Contrast : Used to adjust the contrast between the object and the background.
3) Brightness : Used to adjust brightness of the entire picture.
4) Sharpness : Used to adjust the sharpness of the picture.
▶ When the input signal is PC Timing(D-Sub/HDMI), the Sharpness
Contrast
cannot be adjusted.
5) Color : Used to adjust color lighter or darker.
▶ When the input signal is PC Timing(D-Sub/HDMI), the Color cannot
Brightness
Sharpness
Color
be adjusted.
6) Tint : Used to obtain more natural color of objects using Green or Red enhancement.
Tint
▶ When the input signal is PC Timing(D-Sub/HDMI)and PAL and
SECAM of the [S-Video] and [AV] modes, the color cannot be adjusted.
7) Color Temperature : You can select the color temperature according to your
preferences.
-
Factory defaults: 5500K, 6500K, 8000K, 9300K
-
You can select the color temperature for the items below according to your
Color
Temperature
preferences.
R-Gain, G-Gain, B-Gain : Adjusts the color temperature of the White level.
R-Offset, G-Offset, B-Offset : Adjusts the color temperature of the Black level.
R-Gain
G-Gain
B-Gain
1) Color Temperature
5) R-Offset
2) R-Gain
6) G-Offset
G-Offset
3) G-Gain
7) B-Offset
B-Offset
R-Offset
4) B-Gain
8) Gamma : Changes the brightness characteristic for each color tone of an image.
-
The larger (+) the value, the greater the contrast of the bright and dark parts; the
smaller (-) the value, the darker the dark parts.
-
Adjustable range: -3 to +3
Gamma
9) Save :You can save the status of a screen you adjusted according to your preferences
using the Mode > User OSD.
Save
10) Reset : Restores the mode settings to the factory defaults.
Reset
Size
You can select a screen size according to the type of scene.
▶ When the input signal is PC Timing(D-Sub/HDMI), Zoom1/Zoom2 is not
supported.
1) Normal
2) Zoom1
3) Zoom2
4) 16:9
5) Custom
Position
Adjust the screen position if it is not aligned.
Digital NR
When a dotted line is displayed or the screen shakes, you can view a better visual quality
picture by enabling Noise Reduction.
▶ When the input signal is PC Timing(D-Sub/HDMI)), Digital NR does not operate.
Black Level
You can select the black level according to the input signal. If it is unsuitable for the input
signal, the dark parts may not be shown clearly or appear dim.
▶ The Black Level can only be set for [AV],[S-Video], the 480i and 576i signals of
AV Timing(D-Sub), and the RGB signal of the [HDMI] mode.
- For [AV],[S-Video] and the 480i and 576i signals of AV Timing(D-Sub).
1) 0 IRE : Sets the black level to 0 IRE
Downloaded From projector-manual.com Samsung Manuals
2) 7.5 IRE : Sets the black level to 7.5 IRE
- For the RGB signal of [HDMI] mode
1) Normal: Used in a normal environment.
2) Low: Used when the dark part is shown too bright.
Overscan
Using this function, you can cut the edge of the picture when unnecessary information,
images appear on the edge of the picture.
▶This is not supported in [AV] and [S-Video] modes.
▶This is supported only when the input signal is AV Timing(D-Sub) or AV Timing
(HDMI).
▶If Overscan is turned off, unnecessary extra parts at the edges of an image may
also be shown.
In this case, turn Overscan on.
Film Mode
Using this function, you can set the display mode optimized for playing movies.
1) Off
2) On
▶ Film Mode can only be supported for the [AV], [S-Video], 480i, and 576i signals.
PC
Eliminates or reduces noise that causes unstable screen quality, such as screen shaking. If
the noise is not removed using Fine Adjustment, adjust the frequency to the maximum and
then perform Fine Adjustment again.
▶ It is only enabled for the PC Timing input of the D-Sub terminal.
Auto
Adjustment
▶ Refer to " PC Timing (D-Sub/HDMI) ".
1) Auto Adjustment : Used to adjust frequency and phase of PC screen automatically.
2) Coarse : Used to adjust frequency when vertical lines appear on PC screen.
Coarse
Fine
3) Fine : Used to fine tune the PC screen.
4) Reset : Using this function, you can reset the PC menu settings to the factory default
Reset
settings.
Zoom
Enlarges the PC screen to 2X, 4X, or 8X.
▶ This can only be adjusted when the input signal is PC Timing(D-Sub/HDMI).
|
* Click the Play(
Screen
)/Stop(
| Input | Picture | Setup | Option |
) button in the table below to view the video file.
Description
Adjustment
Install
Basic Functions
To tailor the picture to the installation location, you can invert the projected images
vertically/horizontally.
Downloaded From projector-manual.com Samsung Manuals
Play/Stop
1) Front-Floor : Normal Image
2) Front-Ceiling : Horizontal/Vertical Reversed Image
3) Rear-Floor : Horizontally Reversed Image
4) Rear-Ceiling : Vertically Reversed Image
Lamp Mode
Used to set the image brightness by adjusting the amount of light generated by the lamp.
1) Eco : This mode is optimized for small screens smaller than 100 inches.
This mode decreases the lamp brightness and power consumption in order to extend
the lamp lifetime and reduce noise and power consumption.
Eco
2) Normal : This mode is optimized for general use. This mode is the recommended
mode for a stable lamp brightness that enables a low-noise, comfortable operating
Normal
environment even under bright ambient illumination.
3) Bright : This mode maximizes the lamp brightness when the ambient illumination is
Bright
bright. As the brightness of the lamp increases, the lamp lifetime can be reduced and
the noise and power consumption may increase.
V-Keystone
When the projector image is not displayed vertically on the screen, the image can be
calibrated using the V-Keystone function.
H-Keystone
When the projector image is not displayed horizontally on the screen, the image can be
calibrated using the H-Keystone function.
Refer to 'Adjusting the H-Keystone'
▶The Keystone, which is a function for calibrating a skewed image, may degrade
image quality when it is activated.
Background
You can set the Background that is displayed when there is no signal from the external device
connected to the projector.If a signal is received, the Background you set disappears and a
normal screen is displayed.
1) Logo
2) Blue
3) Black
Test Pattern
Generated by the projector itself. Use to optimize the installation of the projector.
Crosshatch
1) Crosshatch : You can check whether the picture is distorted or not.
2) Screen Size : You can refer to picture format sizes such as 1.33:1 or 1.78:1.
Screen
Size
Video Type
If the screen quality is abnormal as a result of the projector not identifying the input signal
type automatically in PC or HDMI mode, you can manually set the input signal.
▶
In [PC] mode, this is only enabled if the input signal is AV Timing(DSub).However, for a separate H/V sync., this is only enabled for the 1280 x
720p 59.94 Hz/60 Hz signals.
▶
In [HDMI] mode, this is only enabled for the 640x480p 59.94Hz/60 Hz,
1280x720p 59.94Hz/60 Hz signals from among the AV Timing(HDMI) signals.
1) Auto
2) RGB(PC)
3) RGB(AV)
4) YPbPr(AV)
Usage
RGB(PC)
When connecting the RGB output of a PC
to the D-Sub terminal
Color,
Sharpness,Tint
PC menu and
zoom
Disabled
Enabled
Enabled
Enable
Enabled
Disabled
Disabled
Enabled
Enabled
Disabled
When connecting the RGB output of an
RGB(AV)
AV device (STB, DVD, etc…) to the DSub terminal
When connecting the YPbPr output of an
YPbPr(AV) AV device (STB, DVD, etc…) to the DSub terminal
PC
AV
When connecting a PC to the HDMI
terminal
When connecting an AV device (STB,
Downloaded From projector-manual.com Samsung Manuals
DVD, etc…) to the HDMI terminal
Auto
Reset
Auto settings
-
-
Using this function, you can reset various settings to the factory default settings.
Factory
1) Factory Default : Changes the settings to the factory defaults.
Default
2) Reset Filter Time : Resets the filter time.
Reset Filter
Time
|
* Click the Play(
Screen
Menu Option
)/Stop(
| Input | Picture | Setup | Option |
) button in the table below to view the video file.
Description
Adjustment
Language
Basic Functions
Play/Stop
You can select the Language used for the menu screen.
1) Position
You can move Menu Position up/down/left/right.
2) Transparency
Position
You can set the translucency of menu.
- Low
- Medium
Transparency
- High
- Opaque
3) Display Time
You can set the display time of the menu.
- 5 sec / 10 sec / 30 sec / 60 sec / 90 sec / 120 sec / Stay On
Sound
Adjusts the right and left audio balance and equalizer of the 3W stereo speaker embedded in
the projector.
Downloaded From projector-manual.com Samsung Manuals
Display
Time
Filter Check
1) Balance
4) 1kHz
2) 100Hz
5) 3kHz
3) 300Hz
6) 10kHz
Sets the check period for the filter. (Unit: hour)
Time
1) Off
2) 100
3) 200
4) 400
5) 800
▶
If the filter usage time is larger than the filter check period, the filter check
message is displayed for a minute whenever the projector is turned on.
▶
Auto Power On
Filter check message: "Check the filter, and if necessary, clean or replace it.".
If the power is supplied to the projector, it is turned on automatically without pressing the
Power button.
1) Off
2) On
Sleep Timer
If there is no input signal for the specified time, the projector is turned off automatically.
(But, for the specified time, there must be no button input from the remote control or the top
of the projector)
1) Off
2) 10 min
3) 20 min
4) 30 min
Information
You can check external source signals, picture setup, PC picture adjustment and lamp use
time.
Downloaded From projector-manual.com Samsung Manuals
Check that your PC and projector are turned off.
Connect the [HDMI/DVI IN] terminal of the projector to the HDMI or DVI terminal of your PC using a HDMI/HDMI or HDMI/DVI
cable (Not supplied).
- When connecting to the HDMI terminal of your PC, use an HDMI cable (Not supplied).
- For the supported input signals, refer to "PC Timing(D-Sub/HDMI)".
Connect the [PC 1/DVI AUDIO IN] terminal of the projector and the Audio out terminal of your PC using an audio cable (Not
supplied).
- If connecting with an HDMI/HDMI cable, an audio cable (Not supplied) is not needed.
Connecting an External Monitor
You can view an image on both your projector and a separate monitor at the same time.
Check that your PC and projector are turned off.
Downloaded From projector-manual.com Samsung Manuals
Connect the [PC IN 1] terminal at the back of the projector to the D-Sub terminal of your PC using a D-Sub cable.
Connect the [PC OUT] terminal of the projector to the D-Sub terminal of a monitor using a D-Sub cable.
- When connecting a monitor using the [PC OUT] function, make sure to connect your PC to the [PC IN 1] terminal.
- The monitor output which is connected to the [PC OUT] termininal will be normal even if you see a blank screen on
your projector.
- The [PC OUT] function also operates in standby mode.
Connecting an HDMI-Compatible Device
First, check that the AV device and your projector are turned off.
Connect the [HDMI/DVI IN] terminal at the back of the projector to the HDMI or HDMI/DVI output terminal of the digital output
device using an HDMI/DVI cable.
- When connecting to the HDMI output terminal of the digital output device, use an HDMI cable.
- For the supported input signals, refer to "AV Timing(HDMI)".
Connect the [PC 1/DVI AUDIO IN] terminal of the projector to the Audio out terminal of your digital output device using an audio
cable (Not supplied).
- If connecting with an HDMI/HDMI cable, an audio cable (Not supplied) is not needed.
Connecting an AV device using a D-Sub cable
Downloaded From projector-manual.com Samsung Manuals
| Care and Maintenance | Contact SAMSUNG WORLDWIDE | Authority |
To clean the exterior and lens of the projector
Clean the projector using a soft dry cloth.
Do not clean the projector with flammable
substances such as benzene, thinners or a wet
cloth, as these may cause problems.
Do not touch the projector with a nail or any other
sharp objects, as this may scratch the surface.
To clean the interior of the projector
For cleaning the interior of the projector,
ask your Service Center or a distributor.
Contact your distributor or a Service Center if dust
or other substances are inside the projector.
Lamp Replacement
Cautions on Lamp Replacement
The projector lamp is an expendable item. For best operating performance, replace the lamp according to the usage
time. You can view the lamp usage time in the Information Display (INFO button).
Use the recommended lamp when replacing. Replace the lamp with the one specified below.
- Lamp Model Name : 220W UHP E19.5
- Lamp Manufacture : Philips
- For inquiries on lamp purchase, please refer to 'Contact SAMSUNG WORLDWIDE'.
Check that the power cord is unplugged before replacing the lamp.
Since the lamp is a high temperature and high voltage product, wait at least one hour from the time that the power
cord is disconnected before replacing it.
The lamp is located on the left side of the projector (when looking from the front).
Do not leave the old lamp near inflammables or in reach of children. There is a danger of burn or injury.
Remove dirts or foreign materials around or inside the lamp unit using a proper vacuum device.
When handling the lamp, avoid touching any part of it except for the handles. If you handle the lamp incorrectly, it
may affect the screen quality and shorten its lifetime.
Before you turn the projector over to change the lamp, cover the projector with a soft cloth on a flat surface.
Downloaded From projector-manual.com Samsung Manuals
The projector has been designed so that the projector does not work if the lamp cover is not completely assembled
after a lamp replacement. If the projector does not work properly, please check the operating status of the
indicator LED.
Contains Mercury, Dispose According to Local, State or Federal Laws
Lamp Replacement Procedure
Since the lamp is a high temperature and high voltage product, wait at least one hour from the time that
the power cord is disconnected before replacing it.
The lamp is located on the left side of the projector (when looking from the front).
Remove the screw shown in the
Remove the two (2) screws shown in
Hold and pull the lamp handle out of
figure below and than open the
the figure below.
the projector, as shown in the figure
cover.
below.
Assembling a new lamp is in the reverse order of the disassembly.
Replacing and Cleaning the Filter
Precautions when replacing the projector filter
The filter is located at the bottom of the projector.
Turn off the power of the projector, and then disconnect the power cord after the heat of the projector is cooled
sufficiently.
Otherwise, its parts may be damaged due to internal heat.
When replacing the filter, dust may occur.
For inquiries on filter purchase, please refer to 'Contact SAMSUNG WORLDWIDE'.
The sequence for replacing or cleaning the filter of the projector.
Turn off the power of the projector,
Place the product so that its bottom
and then disconnect the power cord
looks upward, and than push and
after the heat of the projector has
remove the filter cover in the
cooled sufficiently.
direction of the arrow.
Replace or clean the filter.
* When placing the product with the
bottom upwards, make sure to place
a soft cloth on the floor to prevent
scratches.
When cleaning the filter, use a small vacuum cleaner for computers and small electronics products, or wash it under
running water.
Downloaded From projector-manual.com Samsung Manuals
When washing the filter under running water, make sure to dry it completely. The moisture may cause the filter to
corrode.
If dust cannot be separated from the filter or the filter is torn, it must be replaced.
Make sure to select the Reset Filter Time option after replacing or cleaning the filter of the projector
Ventilating openings
The location of the ventilation openings
The ventilation openings are located on the right and left sides and at the bottom of the projector.
| Care and Maintenance | Contact SAMSUNG WORLDWIDE | Authority |
If you have any questions or comments relating to Samsung products,
please contact a SAMSUNG customer care center.
North America
U.S.A
1-800-SAMSUNG(726-7864)
http://www.samsung.com/us
CANADA
1-800-SAMSUNG(726-7864)
http://www.samsung.com/ca
MEXICO
01-800-SAMSUNG(726-7864)
http://www.samsung.com/mx
Latin America
ARGENTINA
BRAZIL
0800-333-3733
0800-124-421
4004-0000
http://www.samsung.com/ar
http://www.samsung.com/br
CHILE
800-SAMSUNG(726-7864)
http://www.samsung.com/cl
COLOMBIA
01-8000112112
http://www.samsung.com/co
COSTA RICA
0-800-507-7267
http://www.samsung.com/latin
ECUADOR
1-800-10-7267
http://www.samsung.com/latin
EL SALVADOR
800-6225
http://www.samsung.com/latin
GUATEMALA
1-800-299-0013
http://www.samsung.com/latin
HONDURAS
800-7919267
http://www.samsung.com/latin
JAMAICA
1-800-234-7267
http://www.samsung.com/latin
NICARAGUA
00-1800-5077267
http://www.samsung.com/latin
PANAMA
800-7267
http://www.samsung.com/latin
PUERTO RICO
1-800-682-3180
http://www.samsung.com/latin
Downloaded From projector-manual.com Samsung Manuals
REP. DOMINICA
1-800-751-2676
http://www.samsung.com/latin
TRINIDAD & TOBAGO
1-800-SAMSUNG(726-7864)
http://www.samsung.com/latin
VENEZUELA
0-800-100-5303
http://www.samsung.com/latin
Europe
AUSTRIA
0810 - SAMSUNG(7267864, € 0.07/min)
http://www.samsung.com/at
http://www.samsung.com/be
BELGIUM
(Dutch)
02 201 2418
http://www.samsung.com/be_fr
(French)
CZECH REPUBLIC
800 - SAMSUNG (800-726786)
http://www.samsung.com/cz
DENMARK
8 - SAMSUNG(7267864)
http://www.samsung.com/dk
EIRE
0818 717 100
http://www.samsung.com/ie
FINLAND
30 - 6227 515
http://www.samsung.com/fi
FRANCE
01 4863 0000
http://www.samsung.com/fr
GERMANY
01805 - SAMSUNG (7267864, € 0.14/Min)
http://www.samsung.de
HUNGARY
06-80-SAMSUNG (726-7864)
http://www.samsung.com/hu
ITALIA
800-SAMSUNG (726-7864)
http://www.samsung.com/it
LUXEMBURG
02 261 03 710
http://www.samsung.com/lu
NETHERLANDS
0900-SAMSUNG (0900-7267864) (€ 0,10/Min)
http://www.samsung.com/nl
NORWAY
3 - SAMSUNG(7267864)
http://www.samsung.com/no
POLAND
0 801 1SAMSUNG(172678)
http://www.samsung.com/pl
022 - 607 - 93 - 33
PORTUGAL
808 20 - SAMSUNG (7267864)
http://www.samsung.com/pt
SLOVAKIA
0800-SAMSUNG (726-7864)
http://www.samsung.com/sk
SPAIN
902 - 1 - SAMSUNG (902 172 678)
http://www.samsung.com/es
SWEDEN
0771 726 7864 (SAMSUNG)
http://www.samsung.com/se
SWITZERLAND
0848 - SAMSUNG(7267864, CHF 0.08/min)
http://www.samsung.com/ch
U.K
0845 SAMSUNG (7267864)
http://www.samsung.com/uk
CIS
BELARUS
810-800-500-55-500
ESTONIA
800-7267
http://www.samsung.com/ee
LATVIA
8000-7267
http://www.samsung.com/lv
LITHUANIA
8-800-77777
http://www.samsung.com/lt
MOLDOVA
00-800-500-55-500
KAZAKHSTAN
8-10-800-500-55-500
KYRGYZSTAN
00-800-500-55-500
RUSSIA
8-800-555-55-55
Downloaded From projector-manual.com Samsung Manuals
http://www.samsung.com/kz_ru
http://www.samsung.ru
TADJIKISTAN
8-10-800-500-55-500
UKRAINE
8-800-502-0000
http://www.samsung.com/ua
http://www.samsung.com/ua_ru
UZBEKISTAN
8-10-800-500-55-500
http://www.samsung.com/kz_ru
Asia Pacific
AUSTRALIA
1300 362 603
http://www.samsung.com/au
400-810-5858
http://www.samsung.com/cn
CHINA
010-6475 1880
http://www.samsung.com/hk
HONG KONG
3698 - 4698
http://www.samsung.com/hk_en
3030 8282
INDIA
1-800-3000-8282
http://www.samsung.com/in
1800 110011
INDONESIA
0800-112-8888
http://www.samsung.com/id
JAPAN
0120-327-527
http://www.samsung.com/jp
MALAYSIA
1800-88-9999
http://www.samsung.com/my
NEW ZEALAND
0800 SAMSUNG (0800 726 786)
http://www.samsung.com/nz
1-800-10-SAMSUNG(726-7864)
PHILIPPINES
1-800-3-SAMSUNG(726-7864)
1-800-8-SAMSUNG(726-7864)
http://www.samsung.com/ph
02-5805777
SINGAPORE
1800-SAMSUNG(726-7864)
http://www.samsung.com/sg
THAILAND
1800-29-3232, 02-689-3232
http://www.samsung.com/th
TAIWAN
0800-329-999
http://www.samsung.com/tw
VIETNAM
1 800 588 889
http://www.samsung.com/vn
Middle East & Africa
SOUTH AFRICA
0860-SAMSUNG(726-7864)
http://www.samsung.com/za
TURKEY
444 77 11
http://www.samsung.com/tr
U.A.E
800-SAMSUNG(726-7864)
8000-4726
http://www.samsung.com/ae
| Care and Maintenance | Contact SAMSUNG WORLDWIDE | Authority |
Information in this document is subject to change without notice.
ⓒ 2009 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
Downloaded From projector-manual.com Samsung Manuals
Downloaded From projector-manual.com Samsung Manuals