Operating Instructions (Compact)
Issue 11/04
sinamics
SINAMICS G110
Warnings, Cautions and Notes
Issue 11/04
The Compact version of the Operating Instructions will cover the majority of
typical applications. It is valid for inverters firmware versions 1.0 and 1.1. For
full details please refer to the Operating Instructions and the Parameter List.
Warnings, Cautions and Notes
The following Warnings, Cautions and Notes are provided for your safety and as a
means of preventing damage to the product or components in the machines
connected.
Specific Warnings, Cautions and Notes that apply to particular activities are
listed at the beginning of the relevant chapters and are repeated or supplemented
at critical points throughout these chapters.
Please read the information carefully, since it is provided for your personal safety
and will also help prolong the service life of your SINAMICS G110 Inverter and the
equipment you connect to it.
!
2
WARNING
¾ This equipment contains dangerous voltages and controls potentially
dangerous rotating mechanical parts. Non-compliance with Warnings or failure
to follow the instructions contained in this manual can result in loss of life,
severe personal injury or serious damage to property.
¾ Only suitable qualified personnel should work on this equipment, and only after
becoming familiar with all safety notices, installation, operation and
maintenance procedures contained in this manual. The successful and safe
operation of this equipment is dependent upon its proper handling, installation,
operation and maintenance.
¾ The DC link of all SINAMICS G110 modules remains at a hazardous voltage
level for 5 minutes after all voltages have been disconnected. Therefore always
wait for 5 minutes after disconnecting the inverter from the power supply before
carrying out work on any modules. The drive unit discharges itself during this
time.
¾ The mains input, DC and motor terminals carry dangerous voltages even if the
inverter is inoperative, wait 5 minutes to allow the unit to discharge after
switching off before carrying out any installation work.
¾ During the parameter download with the STARTER commissioning tool or
from the BOP to the inverter, the digital output may produce a spurious signal.
Prior to performing a download to the inverter appropriate counter-measures
must be taken to ensure that any suspended load is secured, for example, by
the use of external brakes or the load being lowered to ground level and
secured.
SINAMICS G110
Operating Instructions (Compact)
Issue 11/04
Warnings, Cautions and Notes
NOTES
¾ This equipment is capable of providing internal motor overload protection in
accordance with UL508C section 42 (refer to P0610 and P0335). I2t monitoring
is ON by default.
Motor overload protection can also be provided using an external PTC via a
digital input.
¾ This equipment is suitable for use in a circuit capable of delivering not more
than 10,000 symmetrical amperes (rms), for a maximum voltage of 230 V
when protected by an H or K type fuse, a circuit breaker or self-protected
combination motor controller.
¾ Use Class 1 75 °C copper wire only with the cross-sections as specified in
Section 2.1
¾ The maximum permissible ambient temperature is, depending on the
equipment, 40 °C or 50 °C (refer to Section 2.1).
¾ Before installing and commissioning, please read these safety instructions and
warnings carefully and all the warning labels attached to the equipment.
¾ Make sure that the warning labels are kept in a legible condition and replace
missing or damaged labels.
SINAMICS G110 Operating Instructions (Compact)
Operating Instructions (Compact)
3
Warnings, Cautions and Notes
4
Issue 11/04
SINAMICS G110
Operating Instructions (Compact)
Issue 11/04
Contents
Contents
1
1.1
1.2
Installation ............................................................................................................... 6
Clearance distances for mounting ............................................................................ 6
Mounting dimensions ................................................................................................ 6
2
2.1
2.2
2.3
2.4
Electrical Installation.............................................................................................. 7
Technical specifications............................................................................................ 7
Power terminals ........................................................................................................ 7
Control terminals....................................................................................................... 7
Block diagram ........................................................................................................... 8
3
3.1
3.2
3.3
Factory setting ........................................................................................................ 9
Specific factory settings for the analog version ........................................................ 9
Specific factory settings for the USS version.......................................................... 10
DIP switches ........................................................................................................... 10
4
Communications................................................................................................... 11
4.1
Establishing communications SINAMICS G110 œ STARTER .............................. 11
5
5.1
5.2
5.3
BOP (Option) ......................................................................................................... 12
Buttons and their Functions .................................................................................... 12
Changing parameters using as an example P0003 "Access level"........................ 13
Cloning parameters with the BOP .......................................................................... 14
6
6.1
6.2
6.2.1
6.2.2
6.2.3
6.2.4
6.2.5
6.2.6
6.2.7
6.2.8
6.2.9
6.2.10
6.2.11
6.2.12
6.2.13
6.2.14
6.3
6.4
Commissioning ..................................................................................................... 15
Quick commissioning .............................................................................................. 15
Commissioning the application ............................................................................... 17
Serial interface (USS) ............................................................................................. 17
Selection of command source ................................................................................ 18
Digital inputs (DIN).................................................................................................. 18
Digital output (DOUT) ............................................................................................. 19
Selection of frequency setpoint............................................................................... 19
Analog input (ADC) ................................................................................................. 20
Motor potentiometer (MOP) .................................................................................... 20
Fixed frequency (FF)............................................................................................... 21
JOG......................................................................................................................... 21
Ramp-function generator (HLG) ............................................................................. 22
Reference / limit frequencies .................................................................................. 22
Motor control ........................................................................................................... 22
Inverter/motor protection......................................................................................... 24
Inverter-specific functions ....................................................................................... 24
Series commissioning ............................................................................................. 27
Parameter reset to factory setting........................................................................... 27
7
7.1
7.2
Displays and messages ....................................................................................... 27
LED status display .................................................................................................. 27
Fault messages and Alarm messages.................................................................... 27
SINAMICS G110
Operating Instructions (Compact)
5
1 Installation
Issue 11/04
1
Installation
1.1
Clearance distances for mounting
100 mm
Fig. 1-1
1.2
Flat Plate
variant only
FSA
FSB
FSC
15 mm
SIDE OF CABINET ENCLOSURE
SIDE OF CABINET ENCLOSURE
The inverters can be mounted adjacent to each other. If they are mounted on top of
each other, however, a clearance of 100 mm has to be observed.
100 mm
>0 mm
30 mm
15 mm
Clearance distances for mounting
Mounting dimensions
Frame
Size
A
Drilling Dimensions
H
W
mm (Inch)
mm (Inch)
140 (5.51)
79 (3.11)
Tightening Torque
Bolts
Nm (lbf.in)
2xM4
2,5 (22.12)
Fig. 1-2
6
B
135 (5.31)
127 (5.00)
4xM4
C
140 (5.51)
170 (6.70)
4xM5
4,0 (35.40)
Mounting dimensions
SINAMICS G110
Operating Instructions (Compact)
Issue 11/04
2 Electrical Installation
2
Electrical Installation
2.1
Technical specifications
1 AC 200 - 240 V r 10 %, 47 - 63 Hz
Order No. 6SL3211-
0AB 11-2xy0* 12-5xy0* 13xy0*
15xy0*
17xy0* 21-1xy0* 21-5xy0* 22-2xy0* 23-0xy0*
0KB 11-2xy0* 12-5xy0* 13xy0*
15xy0*
17xy0*
Frame Size
Inverter Output
Rating
kW
hp
Output Current
(perm. ambient temp.)
Input Current
(230 V)
Recommended
Fuse
Input Cable
Output Cable
Tightening
Torque of power
terminals
0,12
0,16
0,25
0,33
0,37
0,5
0.9
1.7
(50 °C)
2.3
(50 °C)
2.3
4.5
6.2
A (50 °C)
A
A
3NA
2
mm
AWG
mm2
AWG
0,75
1,1
1,0
1,5
3.9
3.2
6.0
(50 °C) (40 ºC) (50 °C)
7.7
10.0
10
10
16
3803
3803
3805
Power terminals
Fig. 2-1
Power Terminals
2.3
Control terminals
-
14.7
0.96 (8.50)
x = A/B o with integrated filter
x = U o without filter
-
C
1,5
2,0
2,2
3,0
3,0
4,0
7.8
(40 ºC)
11.0
(50 °C)
13.6
(40 ºC)
19.7
27.2
32.0
35
3814
4,0 - 10
11 - 8
2,5 - 10
12 - 8
50
3820
6,0 - 10
10 - 8
2,5 - 10
12 - 8
20
25
3807
3810
1,0 - 2,5 1,0 - 2,5 1,0 - 2,5 1,0 - 2,5 1,5 - 2,5 2,5 - 6,0 2,5 - 6,0
16 - 12 16 - 12 16 - 12 16 - 12 14 - 12 12 - 10 12 - 10
1,0 - 2,5 1,0 - 2,5 1,0 - 2,5 1,0 - 2,5 1,0 - 2,5 1,5 - 6,0 1,5 - 6,0
16 - 12 16 - 12 16 - 12 16 - 12 16 - 12 14 - 10 14 - 10
10
3803
2.2
8
9
10
0,55
0,75
10
Nm
(lbf.in)
Designation
DOUTDOUT+
DIN0
DIN1
DIN2
Variant
ADC
-
-
B
3803
*o the last digit of the Order No. depends
on hardware and software changes
Term.
1
2
3
4
5
6
7
-
A
1.50 (13.30)
2.25 (19.91)
y = A o analog version
y = B o USS version
Function
Digital output (-)
Digital output (+)
Digital input 0
Digital input 1
Digital input 2
Isolated output +24 V / 50 mA
Output 0 V
Analog
USS
Output +10 V
RS485 P+
Analog input
RS485 NOutput 0 V
SINAMICS G110
Operating Instructions (Compact)
7
2 Electrical Installation
2.4
Block diagram
Fig. 2-2
Inverter block diagram
8
Issue 11/04
SINAMICS G110
Operating Instructions (Compact)
Issue 11/04
3
3 Factory setting
Factory setting
The SINAMICS G110 frequency inverter has already been programmed at the
factory (motor parameters P0304, P0305, P0307, P0310), for standard V/f
applications on Siemens 4-pole asynchronous motors 1LA that have the same
power rating as the inverters
Further factory setting
3.1
Command sources
P0700 see Section 3.1/3.2
Setpoint source
P1000 see Section 3.1/3.2
Motor cooling
P0335 = 0 (self-cooled)
Motor current limit
P0640 = 150%
Min. frequency
P1080 = 0 Hz
Max. frequency
P1082 = 50 Hz
Ramp-up time
P1120 = 10 s
Ramp-down time
P1121 = 10 s
Control mode V/f
P1300 = 0 (V/f with linear characteristic)
Specific factory settings for the analog version
Digital input
Terminals
Parameter
Function
Command source
3, 4, 5
P0700 = 2
Digital input
Setpoint source
9
P1000 = 2
Analog input
Digital input 0
3
P0701 = 1
ON / OFF1 (I/O)
Digital input 1
4
P0702 = 12
Reverse (
Digital input 2
5
P0703 = 9
Fault reset (Ack)
Control method
-
P0727 = 0
Siemens standard control
Fig. 3-1
)
Connections, analog version
SINAMICS G110
Operating Instructions (Compact)
9
3 Factory setting
3.2
Issue 11/04
Specific factory settings for the USS version
Inputs
Terminals
Parameter
Function
Command source
P0700 = 5
Via the USS protocol
Setpoint source
P1000 = 5
Frequency input via the USS protocol
USS address
P2011 = 0
USS address = 0
USS baud rate
P2010 = 6
USS baud rate = 9600 bps
USS-PZD length
P2012 = 2
Two 16-bit words are in the PZD section
of the USS telegram.
Fig. 3-2
8, 9
Connections, USS version
Bus termination
SIMATIC S7-200
G110
G110
G110
max. 31 SINAMICS
Fig. 3-3
3.3
Example, USS bus
DIP switches
The default motor base frequency of the SINAMICS G110 inverter is 50 Hz. For
motors, which are designed for a base frequency of 60 Hz, the inverters can be set
to this frequency via a DIP switch.
Bus termination on USS variant
It is necessary to terminate the last inverter on the network bus. This is achieved by
setting the Bus Termination DIP switches (DIP switches 2 and 3) on the front of the
inverter to the ‘Bus Termination’ position (ON position). A common 0 V reference
(terminal 10) is required between all devices on the USS bus.
Fig. 3-4
10
Motor Base Frequency DIP Switch and Bus Termination
SINAMICS G110
Operating Instructions (Compact)
Issue 11/04
4 Communications
4
Communications
4.1
Establishing communications SINAMICS G110 œ
STARTER
The following optional components are additionally required in order to establish
communications between STARTER and SINAMICS G110:
¾ PC <-> frequency inverter connecting kit (order no 6SL3255-0AA00-2AA0)
¾ BOP, as far as the USS standard settings already kept in the Sinamics G110
shall be changed (order no 6SL3255-0AA00-4BA0)
PC <-> SINAMICS G110 connecting Kit
SINAMICS G110
USS settings, refer to Section 6.2.1, Page 17.
STARTER
Menu, Options --> Set PG/PC interface -->
Select "PC COM-Port (USS)" --> Properties
--> Interface "COM1", select a baud rate
NOTE
The USS parameter settings in the SINAMICS
G110 frequency inverter and the settings in
STARTER must match!
SINAMICS G110
Operating Instructions (Compact)
11
5 BOP (Option)
Issue 11/04
5
BOP (Option)
5.1
Buttons and their Functions
Panel/
Button
Function
Effects
Indicates
Status
The LCD displays the settings currently used by the converter.
Start
converter
Pressing the button starts the converter. This button is disabled by default.
Activate the button: P0700 = 1 or P0719 = 10 ... 15
OFF1
Stop
converter
OFF2
Pressing the button causes the motor to come to a standstill at the
selected ramp down rate. This button is disabled by default.
Activate the button: P0700 = 1 or P0719 = 10 ... 15
Pressing the button twice (or once long) causes the motor to coast
to a standstill.
This function is always enabled.
Change
direction
Press this button to change the direction of rotation of the motor. Reverse is
indicated by a minus (-) sign or a flashing decimal point. Disabled by default.
Activate the button: P0700 = 1 or P0719 = 10 ... 15.
Jog motor
In the " Power-on/Ready" state, when this key is pressed, the motor starts
and rotates with the pre-set jog frequency. The motor stops when the button
is released. Pressing this button when the motor is running has no effect.
Functions
This button can be used to view additional information.
It works by pressing and holding the button. It shows the following, starting
from any parameter during operation:
1. DC link voltage (indicated by d – units V)
2. output frequency (Hz)
3. output voltage (indicated by o – units V).
4. The value selected in P0005 (If P0005 is set to show any of the above
(1 - 3) then this will not be shown again).
Additional presses will toggle around the above displays.
Jump Function
From any parameter (rxxxx or Pxxxx) a short press of the Fn button will
immediately jump to r0000, you can then change another parameter, if
required. Upon returning to r0000, pressing the Fn button will return you to
your starting point.
Acknowledgement
If alarm and fault messages are present, then these can be acknowledged by
pressing key Fn.
Access
Pressing this button allows access to the parameters.
parameters
12
Increase
value
Pressing this button increases the displayed value.
Decrease
value
Pressing this button decreases the displayed value.
SINAMICS G110
Operating Instructions (Compact)
Issue 11/04
5.2
5 BOP (Option)
Changing parameters using as an example P0003
"Access level"
Step
Result on display
1
Press
to access parameters
2
Press
until P0003 is displayed
3
Press
to access the parameter value level
4
Press
or
5
Press
to confirm and store the value
6
Now access level 3 is set and all level 1 to level 3 parameters are visible to the user.
to the required value (example: 3)
SINAMICS G110
Operating Instructions (Compact)
13
5 BOP (Option)
5.3
Issue 11/04
Cloning parameters with the BOP
A single parameter set can be uploaded from an inverter SINAMICS G110 and
then downloaded into another SINAMICS G110 inverter. To clone a parameter set
from one inverter to another, the following procedure should be performed:
Upload (SINAMICS G110 o BOP)
1. Connect the BOP to the inverter SINAMICS G110 which parameters you wish
to copy.
2. Ensure that it is safe to stop the inverter.
3. Stop the inverter.
4. Set parameter P0003 to 3.
5. Set parameter P0010 to 30 to enter Cloning Mode.
6. Set parameter P0802 to 1 to start the upload from the Inverter to the BOP.
7. During the upload “BUSY” will be displayed.
8. The BOP and the inverter will not react to any commands during upload.
9. If the upload has been completed successfully, the BOP display will return to
normal and the inverter will return to a ready state.
10. If the upload has failed:
Attempt another upload or perform a factory reset.
11. The BOP can now be removed from the inverter.
Download (BOP o SINAMICS G110)
1. Connect the BOP to the SINAMICS G110 inverter, in which the parameter set
is to be downloaded.
2. Ensure power is applied to the inverter.
3. Set parameter P0003 to 3.
4. Set parameter P0010 to 30 to enter Cloning Mode.
5. Set parameter P0803 to 1 to start the download from the BOP to the inverter.
6. During the download “BUSY” will be displayed.
7. During download the BOP and the inverter will not react to any commands
during download.
8. If the download has been completed successfully, the BOP display will return
to normal and the inverter will return to a ready state.
9. If the download has failed:
Attempt another download or perform a factory reset.
10. The BOP can now be removed from the inverter.
NOTE
The following important restrictions should be considered when using the
Cloning procedure:
¾ Only the current dataset is uploaded to the BOP.
¾ Once the cloning procedure has started, it cannot be interrupted.
¾ It is possible to copy data from inverters of different power and voltage ratings.
¾ During download, if the data is not compatible with the inverter (e.g. different
firmware releases) the default values for the parameter will be written to the
inverter.
¾ During the cloning process any data already held by the BOP is overwritten.
¾ If the download or upload of data fails, the inverter will not function correctly.
14
SINAMICS G110
Operating Instructions (Compact)
Issue 11/04
6 Commissioning
6
Commissioning
6.1
Quick commissioning
The quick commissioning function will adapt the inverter to the motor and will set
important technological parameters. The quick commissioning can be omitted if a
4-pole 1LA Siemens motor will be used, which matches the rating data of the
frequency inverter.
In order to have access to all motor parameters it is recommended to set the user
access level P0003=3 (see 5.2)
Parameters, designated with a * offer more setting possibilities than are actually
listed here. Refer to the parameter list for additional setting possibilities.
START
Factory setting
P0010 = 1
0
Commissioning parameter *
0 Ready
1 Quick commissioning
30 Factory setting
NOTE
P0010 should be set to 1 in order to parameterize the data of the motor rating
plate.
0
Europe/ North America
(enters the default motor base frequency and power
settings hp/kW)
P0100 = 1
0 Europe [kW], frequency default 50 Hz
1 North America [hp], frequency default 60 Hz
2 North America [kW], frequency default 60 Hz
P0100 = 0, 2 NOTE
For P0100 = 0 or 1, the setting of the DIP switch
must be in line with the value of P0100 (refer to the
parameter list).
P0100 =...
NOTICE
Motor parameters must be accurately
configured for motor overload protection
to operate correctly above 5 Hz.
230 V
P0304 =... P0304 =... Rated motor voltage
(Nominal motor voltage [V] from rating
plate)
The rated motor voltage on the rating
plate must be checked, regarding the
star/delta circuit configuration to ensure
that it matches with the circuit
connection configured at the motor
terminal board
P0310 P0304
P0307 P0305
P0308 P0311
P0305 =... P0305 =... Rated motor current
(Nominal motor current [A] from rating plate)
FU-spec.
FU-spec.
P0307 =... P0307 =... Rated motor power
(Nominal motor power [kW/hp] from rating plate)
If P0100 = 0 or 2, value will be in kW. If P0100 = 1, value will be in in hp.
SINAMICS G110
Operating Instructions (Compact)
15
6 Commissioning
P0308 =...
Issue 11/04
P0308 =... Rated motor cosPhi
(Nominal motor power factor (cos M) from rating plate)
If the setting is 0, the value is automatically calculated
P0100 = 1: P0308 no significance, no entry required.
P0309 =... P0309 =... Rated motor efficiency
(Nominal motor efficiency in [%] from rating plate)
Setting 0 causes internal calculation of value.
P0100 = 0, 2: P0309 no significance, no entry required.
16
0
0
P0310 =...
Rated motor frequency
(Nominal motor frequency in [Hz] from rating plate)
Pole pair number recalculated automatically if parameter is changed.
50.00 Hz
P0311 =...
Rated motor speed
(Nominal motor speed in [rpm] from rating plate)
Setting 0 causes internal calculation of value.
NOTE
For slip compensation, the input is absolutely necessary.
FU-spec.
P0335 =...
Motor cooling
(Selects motor cooling system used)
0 Self-cooled: Using shaft mounted fan attached to motor
1 Force-cooled: Using separately powered cooling fan
P0640 =...
150 %
Motor overload factor
(Motor overload factor in [%] relative to P0305)
This defines the limit of the maximum output current as a % of the rated motor
current (P0305).
P0700 =...
Selection of command source
(see Section 6.2.2 "Selection of command source")
0 Factory default setting
1 BOP (keypad)
2 Terminal
5 USS
2/5
P1000 =...
Selection of frequency setpoint
(see Section 6.2.5 "Selection of frequency setpoint")
1 MOP setpoint
2 Analog setpoint
3 Fixed frequency
5 USS
2/5
P1080 =...
0.00 Hz
Min. frequency
(enters the minimum motor frequency in Hz)
Sets minimum motor frequency at which motor will run irrespective of frequency
setpoint. The value set here is valid for both clockwise and anticlockwise rotation.
P1082 =...
50.00 Hz
Max. frequency
(enters the maximum motor frequency in Hz)
Sets maximum motor frequency at which motor will run irrespective of the
frequency setpoint. The value set here is valid for both clockwise and
anticlockwise rotation.
P1120 =...
10.00 s
Ramp-up time
(enters the ramp-up time in s)
Time taken for motor to accelerate from standstill up to maximum motor frequency
(P1082) when no rounding is used.
P1121 =...
10.00 s
Ramp-down time
(enters the deceleration time in s)
Time taken for motor to decelerate from maximum motor frequency (P1082) down
to standstill when no rounding is used
P1135 =...
OFF3 ramp-down time
(enters the fast stop ramp-down time in s)
Defines ramp-down time from maximum frequency to standstill for OFF3
command.
0
5.00 s
SINAMICS G110
Operating Instructions (Compact)
Issue 11/04
6 Commissioning
P1300 =...
Control mode
(enters the required control mode)
0 V/f with linear characteristic
2 V/f with quadratic characteristic
3 V/f with programmable characteristic
0
P3900 = 1
End of quick commissioning
(means: the start of the motor calculation)
0 No quick commissioning (no motor calculations)
1 End quick commissioning, with factory reset of all other settings
2 End quick commissioning, with factory reset of I/O settings
3 End quick commissioning, without reset of all other settings
NOTE
For P3900 = 1,2,3 o P0340 is internally set to 1 and the appropriate data
calculated (refer to the parameter list P0340).
P3900=3 is useful in case of motor change
0
END
6.2
End of quick commissioning/ drive setting
If additional functions must be implemented at the drive inverter, use the following
Section "Commissioning the application". We recommend this procedure for
drives with a high dynamic response.
Commissioning the application
An application is commissioned to adapt/optimize the frequency inverter - motor
combination to the particular application. The frequency inverter offers numerous
functions - but not all of these are required for the particular application. These
functions can be ignored when commissioning the application. A large portion of
the possible functions are described here; refer to the parameter list for additional
functions.
Parameters, designated with a * offer more setting possibilities than are actually
listed here. Refer to the parameter list for additional setting possibilities.
START
Factory setting
P0003 = 3
6.2.1
User access level *
1 Standard (Allows access into most frequently used parameters)
2 Extended (Allows extended access e.g. to inverter I/O functions)
3 Expert (for expert use only)
1
Serial interface (USS)
P2010 =...
USS baud rate
Sets baud rate for USS communication.
6
P2011 =...
USS address
Sets unique address for inverter.
0
P2012 =...
2
USS PZD length
Defines the number of 16-bit words in PZD part of USS telegram.
P2013 =...
127
USS PKW length
Defines the number of 16-bit words in PKW part of USS telegram.
SINAMICS G110
Operating Instructions (Compact)
Possible
Settings:
3 1200 baud
4 2400 baud
5 4800 baud
6 9600 baud
7 19200 baud
8 38400 baud
9 57600 baud
17
6 Commissioning
Issue 11/04
6.2.2
Selection of command source
P0700 =...
Selection of command source
Selects digital command source.
0 Factory fault setting
1 BOP (keypad)
2 Terminal
5 USS
6.2.3
2/5
P0700
G110 AIN
G110 USS
Settings
0
1
2
5
X
X
X
–
X
X
X
X
–
–
See 6.2.3
See 6.2.1
Digital inputs (DIN)
P0701=...
Function of digital input 0
Terminal 3
1
P0702 =...
Function digital input 1
Terminal 4
12
P0703 =...
Function digital input 2
Terminal 5
9
P0704 =...
Function digital input 3
Via analog input (AIN version only)
Terminals 9, 10
FF selection (15, 16) not possible
0
P0724 =...
3
Debounce time for digital inputs
Defines debounce time (filtering time) used
for digital inputs.
0 No debounce time
1 2.5 ms debounce time
2 8.2 ms debounce time
3 12.3 ms debounce time
P0727 =...
2-wire/3wire control method
Determines the control method using the terminals
0 Siemens Standard (Start / Direction)
1 2-wire (FWD / REV)
2 3-wire (FWD P / REV P)
3 3-wire (Start P / Direction)
Possible Settings:
0 Digital input disabled
1 ON / OFF1
2 ON Reverse / OFF1
3 OFF2 – coast to standstill
4 OFF3 – quick ramp-down
9 Fault acknowledge
10 JOG right
11 JOG left
12 Reverse
13 MOP up (increase frequency)
14 MOP down (decrease frequency)
15 Fixed setpoint (Direct selection)
16 Fixed setpoint (Direct selection + ON)
21 Local/remote
25 DC brake enable
29 External trip
See P0727 for redefinition of settings 1, 2, 12
0
"P" denotes "Pulse"; "FWD" denotes "FORWARD"; "REV" denotes "REVERSE"
Redefined Digital Inputs
P0727=0
P0727=1
P0727=2
P0727=3
Siemens standard control
2-wire control
3-wire control
3-wire control
1
ON/OFF1
ON_FWD
STOP
ON_PULSE
2
ON REV/OFF1
ON_REV
FWDP
OFF1/HOLD
12
REV
REV
REVP
REV
Settings P0701 – P0704
DIN channel
Kl.7 0 V
Debounce time for digital inputs
0 ... 3
P0724 (3)
24 V
T
Function of digital input 0
0 ... 29
P0701 (1)
0
0
...
&
29
0V
Function
Kl.6 P24
r0722
r0722
CO/BO: Binary input values
18
SINAMICS G110
Operating Instructions (Compact)
Issue 11/04
6.2.4
6 Commissioning
Digital output (DOUT)
P0731 =...
Function of digital output 0*
Defines source of digital output 0.
5
P0748 = 0
Invert digital output
Allows the signals to be output to be inverted.
0
Status of DOUT at logically active signal (0 = Open; 1 = Closed)
Frequent settings:
Active
Status
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
High
High
High
High
Low
Low
High
High
High
High
High
High
High
High
0 (always)
1 (always)
1
1
1
0
0
0
1
1
1
1
1
0
1
0
Not Active
Active
Drive ready
Drive ready to run
Drive running
Drive fault active
OFF2 active
OFF3 active
Switch on inhibit active
Drive warning active
Deviation between fset and fact < 3 Hz
PZD control (P0700=5)
Act. Freq • P1082 (fmax)
Warning: Motor current limit
Motor holding brake active*
Motor overload
*Note: Motor holding brake active means the brake is open.
DOUT channel
Invert digital outputs
0 ... 1
P0748 (0)
CO/BO: State of digital outputs
r0747
r0747.0
0
0
...
Functions
Function of digital output 0
0 ... 22
P0731 (5)
1
-1
2
23
1
6.2.5
P1000 =...
DOUT+
24 V DC 50 mA
DOUT-
Selection of frequency setpoint
Selection of frequency setpoint
0 No main setpoint
1 MOP setpoint
2 Analog setpoint
3 Fixed frequency
5 USS
SINAMICS G110
Operating Instructions (Compact)
2/5
P1000
0
1
2
3
5
G110 AIN G110 USS
X
X
X
X
–
X
X
–
X
X
Settings
–
see 6.2.7
see 6.2.6
see 6.2.8
see 6.2.1
19
6 Commissioning
6.2.6
P0757 =...
Issue 11/04
Analog input (ADC)
0V
Value x1 of ADC scaling
P0761 > 0
0 < P0758 < P0760
P0759 =...
P0760 =...
P0761 =...
0.0 %
Value y1 of ADC scaling
This parameter represents the value
of x1 as a % of P2000 (reference
frequency).
10 V
Value x2 of ADC scaling
4000 h
max
P0760
100.0 %
Value y2 of ADC scaling
This parameter represents the value
of x2 as a % of P2000 (reference
frequency).
P0758
10 V
P0757
x100%
V
P0759
P0761
0V
Width of ADC deadband
Defines width of deadband on analog
input.
P0757 = P0761
min
ADC channel
KL8
+10 V
0 > P0758 > P0760
100 %
P0753
P0757
P0758
P0759
P0760
P0758 =...
||
%
r0754
P0761
P1000 = 2
KL9
KL10
A
ADC
dead
zone
ADC
scaling
D
r0752
Setpoint
P0704 = x
1.7 V
1
0
6.2.7
Function
r0722
r0722.3
3.9 V
Motor potentiometer (MOP)
P1031 =...
0
Setpoint memory of the MOP
Saves last motor potentiometer setpoint (MOP) that was active before OFF command or
power down.
0 MOP setpoint will not be stored
1 MOP setpoint will be stored (P1040 is updated)
P1032 =...
Inhibit negative MOP setpoints
0 Neg. MOP setpoint is allowed
1 Neg. MOP setpoint inhibited
P1040 =...
Setpoint of the MOP
Determines setpoint for motor potentiometer control.
1
5.00 Hz
MOP ramp-up and ramp-down times are defined by the parameters P1120 and P1121.
Possible parameter settings for the selection of MOP:
Selection
DIN
BOP
USS *)
P0719 = 0, P0700 = 2, P1000 = 1
or
P0719 = 1, P0700 = 2
P0719 = 0, P0700 = 1, P1000 = 1
or
P0719 = 1, P0700 = 1
or
P0719 = 11
P0719 = 0, P0700 = 5, P1000 = 1
or
P0719 = 1, P0700 = 5
or
P0719 = 51
MOP up
MOP down
P0702 = 13
(DIN1)
P0703 = 14
(DIN2)
UP button
DOWN button
USS control word USS control word
r2036 Bit13
r2036 Bit14
*) SINAMICS G110 CPM110 USS only
20
SINAMICS G110
Operating Instructions (Compact)
Issue 11/04
6.2.8
6 Commissioning
Fixed frequency (FF)
There are 2 types of fixed frequencies:
1. Direct selection (P0701 – P0703 =15)
2. Direct selection + ON command (P0701 – P0703 = 16)
For P0727 = 2, 3: if more than one setting ‘16’ is used, each time the digital input
(set to 16) receives a pulse, it will delatch the previously assigned fixed frequency
thus “overwriting the previously fixed frequency”.
For P0727= 1, 2, 3: at least one of the digital inputs is requested to be assigned
‘setting 16’ to allow an ON command to be issued
P1001 =...
Fixed frequency 1
Defines the setpoint for the fixed frequency 1 (FF1) in Hz.
Hinweis:
Can be directly selected via DIN0 or USS (P0701 = 15, 16).
0.00 Hz
P1002 =...
Fixed frequency 2
Can be directly selected via DIN1 or USS (P0701 = 15, 16).
5.00 Hz
P1003 =...
Fixed frequency 3
Can be directly selected via DIN2 or USS (P0701 = 15, 16).
10.00 Hz
6.2.9
P1058 =...
P1060 =...
JOG
5.00 Hz
JOG frequency
Frequency in Hz when the motor is being
jogged in the selected direction of rotation.
10.00 s
JOG ramp-up/down time
Ramp-up/down time. The JOG ramp-up is
limited by P1058.
JOG
P1082
(f max )
f
P1058
P1060
SINAMICS G110
Operating Instructions (Compact)
P1060
t
21
6 Commissioning
6.2.10
P1091 =...
Issue 11/04
Ramp-function generator (HLG)
Skip frequency (entered in Hz) 0.00 Hz
Defines skip frequency which avoids
effects of mechanical resonance and
suppresses frequencies within +/- 2 Hz
(skip frequency bandwidth).
fout
2 Hz
P1091
P1120 =...
10.00 s
Ramp-up time
(enters the accelerating time in s)
P1121 =...
10.00 s
Ramp-down time
(enters the deceleration time in s)
P1130 =...
Rump-up initial rounding time
(entered in s)
P1134 =...
Rounding type
0 Continuous smoothing
1 Discontinuous smoothing
P1135 =...
6.2.11
fin
f
P1082
(fmax)
f1
0.00 s
0
t
P1120
P1121
5.00 s
OFF3 ramp-down time
Defines ramp-down time from maximum frequency to standstill for OFF3 command.
Reference / limit frequencies
P1080 =...
0.00 Hz
Min. frequency (entered in Hz)
Sets minimum motor frequency [Hz] at which motor will run irrespective of frequency
setpoint. If the setpoint falls below the value of P1080, then the output frequency is set to
P1080 taking into account the sign.
P1082 =...
50.00 Hz
Max. frequency (entered in Hz)
Sets maximum motor frequency [Hz] at which motor will run irrespective of the frequency
setpoint. If the setpoint exceeds the value P1082, then the output frequency is limited. The
value set here is valid for both clockwise and anticlockwise rotation.
P2000 =...
50.00 Hz
Reference frequency (entered in Hz)
The reference frequency in Hertz corresponds to a value of 100 %. This setting should be
changed if a maximum frequency of higher than 50 Hz is required. It is automatically
changed to 60 Hz if the standard 60 Hz frequency was selected using the DIP50/60 switch
or P0100.
NOTE
This reference frequency effects the setpoint frequency since both the analog setpoints
(100% P2000) as well as the frequency setpoints via USS (4000H P2000) refer to this
value.
6.2.12
P1300 =...
22
Motor control
0
Control mode
The control type is selected using this parameter. For the "V/f characteristic" control type,
the ratio between the frequency inverter output voltage and the frequency inverter output
frequency is defined.
0 V/f with linear
2 V/f with quadratic characteristic
3 V/f with programmable characteristic (o P1320 – P1325)
SINAMICS G110
Operating Instructions (Compact)
Issue 11/04
P1310 =...
6 Commissioning
50.00 %
Continuous boost (entered in %)
Voltage boost as a % relative to P0305 (rated motor current) and P0350 (stator resistance).
P1310 is valid for all V/f characteristics (refer to P1300). At low output frequencies, the
effective resistance values of the winding must be taken into account in order to maintain
the motor flux.
Linear V/f
V
Boost voltage
Vmax
Validity range
Vn
(P0304)
actual VBoost
VConBoost,100
VConBoost,50
0
olt
tv
u
p
t
Ou
f
V/ )
al = 0
m
or 0
N 130
P
(
e
ag
ON
OFF
t
P1310 active
1
0
fn
f max
(P0310) (P1082)
fBoost,end
(P1316)
t
~f~
t
f
P1311 =...
0.0 %
Acceleration boost (entered in %)
Voltage boost for accelerating/braking as a % relative to P0305 and P0350. P1311 only
results in a voltage boost when ramping-up/ramp-down and generates an additional torque
for accelerating/braking. Contrary to parameter P1312, that is only active for the 1st
acceleration operation after the ON command, P1311 is effective each time that the drive
accelerates or brakes.
P1312 =...
0.0 %
Starting boost (entered in %)
Voltage boost when starting (after an ON command) when using the linear or quadratic V/f
characteristic as a % relative to P0305 (rated motor current) or P0350 (stator resistance).
The voltage boost remains active until
1) the setpoint is reached for the first time and
2) the setpoint is reduced to a value that is less than the present ramp-function generator
output.
P1320 =...
Programmable V/f freq. 0.0 Hz
coord. 1
Sets V/f coordinates
(P1320/1321 to P1324/1325) to
define V/f characteristic.
P1321 =...
Programmable V/f volt.
coord. 1
P1322 =...
Programmable V/f freq. 0.0 Hz
coord. 2
P1323 =...
Programmable V/f volt. 0.0 Hz
coord. 2
P1324 =...
Programmable V/f freq. 0.0 Hz
coord. 3
P1325 =...
Programmable V/f volt.
coord. 3
P1334 =...
Slip compensation activation range (entered in %)
Starting point for slip compensation is P1334 x P0310.
Upper threshold is always P1334 + 4%
P1335 =...
0.0 %
Slip compensation (entered in %)
Dynamically adjusts output frequency of inverter so that motor speed is kept constant
independent of motor load.
SINAMICS G110
Operating Instructions (Compact)
0.0 Hz
0.0 Hz
6.0 %
23
6 Commissioning
6.2.13
Issue 11/04
Inverter/motor protection
0
P0290 =...
Inverter overload reaction
Selects reaction of inverter to an internal overtemperature
0 Reduce output frequency
1 Trip (F0004 / F0005)
P0335 =...
Motor cooling (enters the motor cooling system)
0 Self-cooled: Using shaft mounted fan attached to motor
1 Force-cooled: Using separately powered cooling fan
P0610 =...
Motor I t reaction
Defines reaction when motor I t reaches warning threshold.
0 Warning, no reaction, no trip
1 Warning, Imax reduction,
2 Warning, no Imax reduction, trip F0011
P0611 =...
100 s
Motor I2t time constant (entered in s)
The time until the thermal limit of a motor is reached, is calculated via the thermal time
constant. A higher value increases the time at which the motor thermal limit is reached. The
value of P0611 is estimated according to the motor data during quick commissioning or is
calculated using P0340 (Calculating of the motor parameters). When the calculation of
motor parameters during quick commission is complete the stored value can be replaced by
the value given by the motor manufacturer
P0614 =...
Motor I t warning level (entered in %)
Defines the value at which alarm A0511 (motor overtemperature) is generated.
0
2
2
2
110.0 %
Trip threshold
1.1˜ P0614
P0611
§ r0027 ·
¸
¨
© P0305 ¹
2
r0034
t
r0021
P0310
( i2 t )
Motor
i2t
temp.
reaction
P0610
F0011
I_max reduction
A0511
P0335
P0614
Warning threshold
P0640 =...
150.0 %
Motor overload factor [%]
Defines motor overload current limit in [%] relative to P0305 (rated motor current). Limited
to maximum inverter current or to 400 % of rated motor current (P0305), whichever is the
lower.
6.2.14
Inverter-specific functions
6.2.14.1
Flying start
0
P1200 =...
Flying start
Starts inverter onto a spinning motor by rapidly changing the output frequency of the
inverter until the actual motor speed has been found.
0 Flying start disabled
1 Flying start is always active, start in direction of setpoint
2 Flying start is active if power on, fault, OFF2, start in direction of setpoint
3 Flying start is active if fault, OFF2, start in direction of setpoint
4 Flying start is always active, only in direction of setpoint
5 Flying start is active if power on, fault, OFF2, only in direction of setpoint
6 Flying start is active if fault, OFF2, only in direction of setpoint
P1202 =...
Motor-current: Flying start (entered in %)
Defines search current used for flying start.relative to rated motor current (P0305)
P1203 =...
100 %
Search rate: Flying start (entered in %)
Sets factor by which the output frequency changes during flying start to synchronize with
turning motor.
24
100 %
SINAMICS G110
Operating Instructions (Compact)
Issue 11/04
6.2.14.2
P1210 =...
6.2.14.3
6 Commissioning
Automatic restart
Automatic restart
Configures automatic restart function.
0 Disabled
1 Trip reset after power on
2 Restart after mains blackout
3 Restart after mains brownout or fault
4 Restart after mains brownout
5 Restart after mains blackout and fault
6 Restart after mains brown/blackout or fault
1
Holding brake
P1215 =...
Holding brake enable 0
Enables/disables holding
brake function (MHB).
0 MBH disabled
1 MBH enabled
NOTE
The MHB is controlled via the
signal of status word 1 r0052
bit 12. This signal can be
issued via the digital output
DOUT0 with parameter
setting P0731=14 for
controlling an external brake
relay.
In firmware version 1.0 r0052
bit 12 will be set when P1216
time has been passed.
P1216 =...
1.0 s
Holding brake release delay (entered in s)
Defines the time interval during which the frequency inverter runs with the min. frequency
P1080, before ramping up
P1217 =...
6.2.14.4
1.0 s
Holding time after ramp-down (entered in s)
Defines time for which inverter runs at minimum frequency (P1080) after ramping down.
DC braking & Compound braking
100 %
P1232 =...
DC braking current (entered in %)
Defines level of DC current in [%] relative to rated motor current (P0305).
P1233 =...
0s
Duration of DC braking (entered in s)
Defines duration for which DC injection braking is to be active following an OFF1 or OFF3
command.
P1234 =...
DC braking start frequency (entered in Hz)
Sets the start frequency for DC braking
P1236 =...
0%
Compound braking current (entered in %)
Defines DC level superimposed on AC waveform after exceeding DC link voltage threshold
of compound braking. This value is entered in % relative to rated motor current (P0305).
P1236=0
Compound braking disabled
P1236=1 - 250
Level of DC braking current defined as % of rated motor current
P0305
SINAMICS G110
Operating Instructions (Compact)
650 Hz
25
6 Commissioning
6.2.14.5
P1240 =...
26
Issue 11/04
Vdc controller
1
Configuration of Vdc controller
Enables / disables Vdc controller.
0 Vdc controller disabled
1 Vdc-max controller enabled
NOTE
P1240 = 1 prevents an overvoltage
condition of the DC link (F0002) in
regenerative operation by extending the
ramp down time.
SINAMICS G110
Operating Instructions (Compact)
Issue 11/04
6.3
7 Displays and messages
Series commissioning
An existing parameter set can be transferred to a SINAMICS G110 frequency
inverter using STARTER or BOP (see 5.3). Typical applications for series
commissioning include:
1. If several drives are to be commissioned that have the same configuration and
same functions. A quick / application commissioning (first commissioning) must
be carried-out for the first drive. Its parameter values are then transferred to the
other drives.
2. When replacing SINAMICS G110 frequency inverters.
6.4
Parameter reset to factory setting
START
P0010=30
Commissioning parameter
30 Factory setting
0
P0970 = 1
Factory reset
0 disabled
1 Parameter reset
0
END
The drive inverter carries-out a parameter reset (duration, approx. 10 s) and then
automatically exits the reset menu and sets:
P0970 = 0 :
disabled
P0010 = 0 :
ready
7
Displays and messages
7.1
LED status display
LED
Meaning
LED Off
Inverter Off / No supply
1000 ms On/1000 ms Off
Power On / Ready
LED On steadily
Inverter Running
500 ms On / 200 ms Off
General Warning
100 ms On / 100 ms Off
Fault Condition
7.2
Fault
Position
LED
Fault messages and Alarm messages
Significance
Alarms
Significance
F0001
Overcurrent
A0501
Current Limit
F0002
Overvoltage
A0502
Overvoltage limit
F0003
Undervoltage
A0503
Undervoltage Limit
F0004
Inverter Overtemperature
A0505
Inverter I2t
2
F0005
Inverter I t
A0511
Motor Overtemperature I2t
F0011
Motor Overtemperature I2t
A0910
Vdc-max controller de-activated
F0051
Parameter EEPROM Fault
A0911
Vdc-max controller active
F0052
Powerstack Fault
A0920
ADC parameters not set properly
F0060
Asic Timeout
A0923
Both JOG Left and JOG Right are
requested
F0072
USS setpoint fault
F0085
External Fault
SINAMICS G110
Operating Instructions (Compact)
27
SINAMICS G110
Operating Instructions (Compact)
Information about SINAMICS G110 is also available from:
Regional Contacts
Please get in touch with your contact for Technical Support in your Region for
questions about services, prices and conditions of Technical Support.
Central Technical Support
The competent consulting service for technical issues with a broad range of
requirements-based services around our products and systems.
Europe / Africa
Tel: +49 (0) 180 5050 222
Fax: +49 (0) 180 5050 223
Email:
adsupport@siemens.com
America
Tel: +1 423 262 2522
Fax: +1 423 262 2289
Email:
simatic.hotline@sea.siemens.com
Asia / Pacific
Tel: +86 1064 719 990
Fax: +86 1064 747 474
Email:
adsupport.asia@siemens.com
Online Service & Support
The comprehensive information system available round the clock via the Internet,
ranging from Product Support and Service & Support services to the Support Tools in
the Shop. http://www.siemens.com/automation/service&support
Internet Home Address
Customers can access technical and general information at:
http://www.siemens.com/sinamics-g110
Siemens AG
Automation & Drives
Standard Drives
Postfach 3269, D – 91050 Erlangen
Germany
www.siemens.com
© Siemens AG 2004
Subject to change without prior notice
Issue 11/04