Bosch PIAxxxF Series Instruction manual

PIA...F...
Hob
[en] Instructions for installation and use
PIA..F...
‘
‘
‘
‘
‘
: :
‘
: :
,(&
2
Ø = cm
Ú Table of contents
enalondusetifr]Insc[ n
INSTALLATION INSTRUCTIONS ............................................... 4
Assembly ................................................................................ 4
Important notes ..............................................................................6
Preparation of assembly kitchen units, figures 1/2/3/4 ........6
Installing the appliance, figures 5/6...........................................7
Changing the intensity of the 13 / 16 / 20 Amp connection
current, figure 7..............................................................................7
Uninstalling the appliance............................................................7
INSTRUCTION MANUAL ............................................................ 8
Safety precautions................................................................. 8
Elements that may damage the appliance ...............................9
Protecting the environment ................................................ 10
Environmentally-friendly disposal............................................. 10
Energy-saving advice ................................................................. 10
Induction cooking................................................................ 10
Advantages of induction cooking ............................................ 10
Suitable pans ............................................................................... 10
Getting to know your appliance.......................................... 11
The control panel........................................................................ 11
The hotplates ............................................................................... 11
Residual heat indicator .............................................................. 12
Programming the hob.......................................................... 12
Turning the hob on and off ....................................................... 12
Setting the hotplate .................................................................... 12
Cooking guidelines table........................................................... 12
Childproof lock..................................................................... 13
Activating and deactivating the childproof lock .................... 13
Childproof lock ............................................................................ 13
Powerboost function ........................................................... 14
To activate ................................................................................... 14
To deactivate ............................................................................... 14
Time programming function ............................................... 14
Turning off a hotplate automatically ........................................ 14
The timer....................................................................................... 14
Cleaning lock function ........................................................ 15
Automatic time limitation .................................................... 15
Displaying energy consumption ........................................ 15
Basic settings....................................................................... 15
Accessing the basic settings.................................................... 16
Care and cleaning................................................................ 17
Hob ................................................................................................ 17
Hob frame .................................................................................... 17
Fixing malfunctions ............................................................. 17
Normal noise while the appliance is working........................ 18
After-sales service............................................................... 18
3
INSTALLATION INSTRUCTIONS
Assembly
‘
[
%
'
ƒ&
(
$
PLQ
$ &
D
(
E
PLQ
PLQ
F
PLQ
PLQ
PLQ
PD[
PLQ
PLQ
PLQ
PLQ
PLQPD[
PLQ
PD[
PLQ
PLQ
PLQ
PLQ
PLQPD[
PLQ
PLQ
PLQ
4
%
PLQ
PLQ
&
'
PLQ
PLQ
PLQ PLQ
PLQ
ƒ
5
D
E
PLQ
PLQ
PLQ
99a
+]+]
/
1
9
9
5
D
E
F
G
Important notes
Assembly over drawer, figure 2a
Safety: Safety in use is only guaranteed if the technical
installation of the hob has been carried out correctly and in
accordance with the assembly instructions. The installation
technician shall be liable for any damage caused as a result of
unsuitable installation.
Metal objects stored inside the drawer could become very hot
due to the air recirculating from the hob ventilation system. If
this occurs, an intermediate support is recommended.
Electric connection: Only by an authorised specialist
technician. The guidelines set out by the local electricity
provider must be observed.
Intermediate support: A wooden panel can be used (figure 3)
or you may order a suitable accessory from our Technical
Assistance Service. The reference code for this accessory
is 686002.
Worktop: Must have a minimum thickness of 20 mm.
Type of connection: The appliance falls under protection
class I and can only be used in combination with a grounding
conductor connection.
The distance between the top of the working surface and the
top of the drawer must be 65 mm.
The manufacturer accepts no responsibility for any malfunction
or damage caused by incorrect electrical installations.
Assembly over oven, figure 2b
Installation: The appliance must be connected to a fixed
installation and the means of disconnecting it from the fixed
installation must be installed according to the installation
instructions.
Built-in assembly under worktop: The induction hobs may
only be installed over a drawer, ovens with forced ventilation
from the same brand and dishwashers from the same brand.
Refrigerators, unventilated ovens and washing machines may
not be installed beneath the hob.
Power cable: Do not tie the power cable or pass it along sharp
edges. If there is an oven installed below, pass the cable along
the rear corners of the oven to the connection box. It must be
positioned so that it does not touch any of the hot parts of the
hob or the oven.
Hob: flat, horizontal, stable. Follow the hob manufacturer's
instructions.
Worktop: Must have a minimum thickness of:
■
20 mm if installed over a compact oven.
■
30 mm if installed over a full-size oven.
If the hob is installed over a compact oven, there must be a
distance of 60 mm between the top of the oven and the top of
the working surface.
Assembly over dishwasher, figure 2c
An intermediate accessory must be installed. The accessory
may be ordered from our Technical Assistance Service. The
reference code for this accessory is 686002.
Worktop: Must have a minimum thickness of 20 mm and
maximum thickness of 40 mm.
The space between the top of the working surface and the top
of the dishwasher must be:
Warranty: an unsuitable installation, connection or assembly
will invalidate the product warranty.
■
60 mm if installed over a compact dishwasher.
■
65 mm if installed over a full-size dishwasher.
Note: Any change to the appliance's interior, including
changing the power cable, must only be performed by specially
trained members of the Technical Assistance Service.
Ventilation, figure 4
Preparation of assembly kitchen units,
figures 1/2/3/4
Built-in kitchen units: Minimum temperature resistance
of 90°C.
Gap: Remove any shavings after performing cutting work.
Cut surfaces: Seal with heat resistant material.
6
Ventilating the hob requires:
■
■
An opening on the upper part of the kitchen unit's rear wall
(figure 4a).
A separation between the rear part of the kitchen unit and
kitchen wall (figure 4b).
Installing the appliance, figures 5/6
Connect the appliance to the mains to check its working.
■
■
Voltage, see specifications plate.
Connect only according to the connection drawing (figure 6).
1. Brown
2. Blue
3. Yellow and green
Changing the intensity of the 13 / 16 / 20 Amp
connection current, figure 7
Before using the hob for the first time, the intensity of the hob
connection must be tested.
Follow the steps below to change the current of the hob:
1. Turn on the hob with the main switch. Do not place any pans
on the hotplates
2. Within the following 60 seconds, adjust all hotplates to the
desired power level according to the required connection
current (see table).
Power level
Connection current in amperes
‚
20 A
ƒ
16 A
„
13 A
3. Turn off all the hotplates in sequence, starting from the lower
right and continuing counter-clockwise.
4. The selected connection current is indicated in the display of
the right-hand lateral hotplates.
5. Turn off the hob with the main switch.
The selected connection current will have been properly saved.
Uninstalling the appliance
Disconnect the appliance from the mains.
Push the hob upwards from below to remove it.
Caution!
Damage to the appliance! Do not try to remove the appliance
by prying it out from above.
7
INSTRUCTION MANUAL
Produk tinfo
Additional information on products, accessories, replacement
parts and services can be found at www.bosch-home.com and
in the online shop www.bosch-eshop.com
: Safety precautions
Please read this manual carefully. Please
keep the instruction and installation manual
as well as the appliance certificate in a safe
place for later use or for subsequent
owners.
Check the appliance after removing it from
the packaging. If it has suffered any
damage in transport, do not connect the
appliance, contact the Technical Assistance
Service and provide written notification of
the damage caused, otherwise you will lose
your right to any type of compensation.
This appliance must be installed according
to the installation instructions included.
This appliance is intended for domestic use
only. The appliance must only be used for
the preparation of food and drink. The
appliance must be supervised during
operation. Only use this appliance indoors.
Do not use lids or unsuitable child safety
grilles. These can cause accidents, due to
overheating, catching fire or materials
shattering, for example.
This appliance is not intended for operation
with an external clock timer or a remote
control.
This appliance may be used by children
over the age of 8 years old and by persons
with reduced physical, sensory or mental
capabilities or by persons with a lack of
experience or knowledge if they are
supervised or are instructed by a person
responsible for their safety how to use the
appliance safely and have understood the
associated hazards.
Children must not play with the appliance.
Children must not clean the appliance or
carry out general maintenance unless they
are at least 8 years old and are being
supervised.
Keep children below the age of 8 years old
at a safe distance from the appliance and
power cable.
Risk of fire!
■ Hot oil and fat can ignite very quickly.
Never leave hot fat or oil unattended.
Never use water to put out burning oil or
fat. Switch off the hotplate. Extinguish
flames carefully using a lid, fire blanket or
something similar.
■ The hotplates become very hot. Never
place combustible items on the hob.
Never place objects on the hob.
■ The appliance gets hot. Do not keep
combustible objects or aerosol cans in
drawers directly underneath the hob.
■ The hob switches off automatically and
can no longer be operated. It may switch
on unintentionally at a later point. Switch
off the circuit breaker in the fuse box.
Contact the after-sales service.
Risk of burns!
■ The hotplates and surrounding area
(particularly the hob surround, if fitted)
become very hot. Never touch the hot
surfaces. Keep children at a safe distance.
■ The hotplate heats up but the display does
not work. Switch off the circuit breaker in
the fuse box. Contact the after-sales
service.
■ Metal objects on the hob quickly become
very hot. Never place metal objects (such
as knives, forks, spoons and lids) on the
hob.
■ After each use, always turn off the hob at
the main switch. Do not wait until the hob
turns off automatically after the pan is
removed.
Risk of electric shock!
■ Incorrect repairs are dangerous. Repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the
appliance from the mains or switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
Risk o f fire!
Risk o f fire!
Risk o f fire!
Risk o f b urn s!
Risk o f b urn s!
Risk o f fire!!
Risk o f electric sho ck!
8
Penetrating moisture may cause an
electric shock. Do not use any highpressure cleaners or steam cleaners.
■ A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in
the fuse box. Contact the after-sales
service.
■ Cracks or fractures in the glass ceramic
may cause electric shocks. Switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
Electromagnetic hazards!
This appliance complies with safety and
electromagnetic compatibility standards.
However, people with pacemakers must
refrain from approaching the appliance
when in use. Although the risk is small, it is
impossible to ensure that all of these
devices available on the market comply
with current electromagnetic compatibility
standards and that interference which may
prevent the device from working correctly
will not occur. It is also possible that people
with other types of devices, such as hearing
aids, could experience some discomfort.
Malfunction risk!
The hob is equipped with a fan in the lower
section. If there is a drawer under the hob it
■
Risk of electric sh ock !
Risk of electric sh ock !
should not be used to store small objects or
paper, since they could damage the fan or
interfere with the cooling if they are sucked
into it.
There should be a minimum of 2 cm
between the contents of the drawer and fan
intake.
Risk of injury!
■ When cooking in a bain marie, the hob
and cooking container could shatter due
to overheating. The cooking container in
the bain marie must not directly touch the
bottom of the water-filled pot. Only use
heat-resistant cookware.
■ Saucepans may suddenly jump due to
liquid between the pan base and the
hotplate. Always keep the hotplate and
saucepan bases dry.
Risk of in jury!
Elements that may damage the appliance
Caution!
■
■
■
■
■
Rough pan bases may scratch the hob.
Avoid leaving empty pots and pans on the hotplate. Doing so
may cause damage.
Do not place hot pans on the control panel, the indicator
area, or the hob frame. Doing so may cause damage.
Hard or pointed objects dropped on the hob may damage it.
Aluminium foil and plastic containers will melt if placed on the
hotplate while it is hot. The use of laminated sheeting is not
recommended on the hob.
Overview
The following table presents the most common damage
caused:
Damage
Cause
Measure
Stains
Food spillage
Immediately remove spilt food using a glass scraper.
Unsuitable cleaning products
Only use cleaning products specifically designed for glass-ceramic hobs.
Salt, sugar and sand
Do not use the hob as a tray or working surface.
Scratches
Pans with rough bottoms may scratch Check pans.
the glass ceramic
Fading
Chips
Unsuitable cleaning products
Only use cleaning products specifically produced for glass-ceramic hobs.
Contact with pans
Lift pots and pans before moving them around.
Sugar, substances with a high sugar Immediately remove spilt food using a glass scraper.
content
9
Protecting the environment
Unpack the appliance and dispose of its packaging in such a
way that no damage is caused to the environment.
Environmentally-friendly disposal
■
■
Dispose of packaging in an environmentally-friendly manner.
This appliance is labelled in accordance with European
Directive 2012/19/EU concerning used electrical and
electronic appliances (waste electrical and electronic
equipment - WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
Energy-saving advice
■
Always use the correct lid for each pan. Cooking without a lid
uses a lot more energy. Use a glass lid to provide visibility
and avoid having to lift the lid.
■
■
■
■
Use pans with flat bases. Bases that are not flat use a lot
more energy.
The diameter of the pan base must match the size of the
hotplate. If the diameter is too small compared to the
hotplate, energy can be wasted. Please note: pan
manufacturers usually provide the diameter for the top of the
pan, which is usually larger than the diameter of the pan
base.
Use a small pan for small amounts of food. A large pan which
is not full uses a lot of energy.
Use little water when cooking. This saves energy and
preserves all the vitamins and minerals in vegetables.
Always cover as much of the hotplate as possible with the
pan.
Select the lowest power level to maintain cooking. If the
power level is too high, energy is wasted.
Induction cooking
Advantages of induction cooking
Other cookware for induction
Induction cooking represents a radical change from the
traditional method of heating; the heat is generated directly in
the pan. It therefore offers a number of advantages:
There are other types of cookware especially made for
induction cooking whose base is not entirely ferromagnetic.
■
■
■
■
When using large cookware on a
smaller ferromagnetic area, only
the ferromagnetic zone heats up,
so heat might not be uniformly
distributed.
Time savings for cooking and frying; since the pan is heated
directly.
Energy is saved.
Care and cleaning are simpler. Foods that have spilt do not
burn as quickly.
Pans with aluminium areas
inserted in the base reduce the
ferromagnetic area, so less heat
may be supplied and the pan
may be difficult to detect or not
be detected at all.
Heat and safety control; the hob supplies or cuts off power as
soon as the control knob is turned on. The induction hotplate
stops supplying heat if the pan is removed without having
previously switched it off.
For good cooking results, the
diameter of the cookware's ferromagnetic area should match the
size of the hotplate. If cookware
is not detected on a hotplate, try
it on the next smaller hotplate
down.
Suitable pans
Ferromagnetic cookware
Only ferromagnetic cookware is suitable for induction cooking,
these may be made from:
■
enamelled steel
■
cast iron
■
special cutlery for stainless steel induction pan.
To determine whether a pan is suitable, check to see if a
magnet will stick to it.
Unsuitable pans
Never use diffuser hobs or pans made from:
■
common thin steel
■
glass
■
earthenware
■
copper
■
aluminium
Characteristics of the pan base
The characteristics of the pan base may affect the uniformity of
the cooking results. Pans made from materials which help
diffuse heat, such as stainless steel sandwich pans, distribute
heat uniformly, saving time and energy.
Absence of pan or unsuitable size
If no pan is placed on the selected hotplate, or if it is made of
unsuitable material or is not the correct size, the power level
displayed on the hotplate indicator will flash. Place a suitable
pan on the hotplate to stop the flashing. If this takes more than
90 seconds, the hotplate will switch off automatically.
10
Empty pans or those with a thin base
Pan detection
Do not heat empty pans, nor use pans with a thin base. The
hob is equipped with an internal safety system. However, an
empty pan may heat up so quickly that the "automatic switch
off" function may not have time to react and the pan may reach
very high temperatures. The base of the pan could melt and
damage the glass on the hob. In this case, do not touch the
pan and switch the hotplate off. If it fails to work after it has
cooled down, please contact the Technical Assistance Service.
Each hotplate has a minimum limit for detecting pans, which
varies depending on the material of the pan being used. You
should therefore use the hotplate that is most suitable for the
diameter of your pan.
Getting to know your appliance
The instruction manual is the same for various different hobs.
An overview of the models with their dimensions is given on
page 2.
The control panel
PLQ
ORZ
PHG
PD[
Indicators
Control panels
%
Main switch
‹
Functionality
$
Select the hotplate
‚ -Š
Power levels
1û2û...8û9
Programming zone
• /œ
Residual heat
>
Cleaning lock function
‹‹
Time program function
D
Childproof lock
V
Timer
boostG
Powerboost Function
x
Automatic shut-off
0
Timer programming
›
Powerboost Function
D
Childproof lock
Control panels
Pressing a symbol activates its corresponding function.
Note: Always keep the control surfaces dry. Moisture can affect
proper working.
The hotplates
Hotplate
Turning on and off
$ Single hotplate
Always use cookware of a suitable size.
Use only cookware suitable for induction cooking; see the section on suitable cookware.
11
Residual heat indicator
The hob has a residual heat indicator for each hotplate to show
those which are still hot. Avoid touching them when this
indicator is lit.
Although the hob is switched off, the indicator œ or • will
remain on for as long as the hotplate is hot.
If the pan is removed before the hotplate is turned off, the
indicator œ or • and the selected power level will appear
alternately.
Programming the hob
This section will show you how to program the hotplates. The
table contains power levels and cooking times for several
dishes.
2. Next, select the power level in the programming zone.
Turning the hob on and off
The hob is turned on and off using the main switch.
To turn on: press the % symbol. A beep sounds. The indicator
located next to the main switch and the ‹ indicators of the
hotplates light up. The hob is ready for use.
To turn off: press the % symbol until the indicators go out. All
hotplates are turned off. The residual heat indicator will remain
lit until the hotplates have cooled down sufficiently.
Notes
The hob switches off automatically when all the hotplates are
switched off for more than 20 seconds.
■
■
The settings are memorised for 4 seconds after the hob has
been turned off. If the hotplate is switched back on within this
time then the previous settings will be applied.
Setting the hotplate
Select the power level required with the 1 to 9 symbols.
Power level 1 = minimum power
Power level 9 = maximum power
Each power level has an intermediate level. This level is marked
with the Ú symbol in the programming zone.
Selecting the power level
The hob must be switched on.
1. Press the $ symbol for the desired hotplate.
The ‹ indicator lights up as well as the ¬ symbol below.
The power level has been set.
Changing the power level
Select the hotplate and then press the symbol for the desired
power level. To select an intermediate level, press the Ú symbol
that is between the power level symbols.
Switch off the hotplate
Select the hotplate and set it to ‹ in the programming panel.
The hotplate turns off and the residual heat indicator appears.
Notes
■ If no pan has been placed on the hotplate, the selected
power level flashes. After a certain time has elapsed, the
hotplate switches off.
■
If a pan has been placed on the hotplate before switching on
the hob, it will be detected within 20 seconds of pressing the
main switch and the hotplate will be selected automatically.
Once detected, select the power level within the next
20 seconds or the hotplate will switch off.
If more than one pan is placed on the hob, only one will be
detected when switching it on.
Cooking guidelines table
The table below contains some examples.
Use power level 9 to begin cooking.
When heating purées, creams and thick sauces, stir frequently.
Power level
Melting
Chocolate, chocolate coating
1-1.
Butter, honey, gelatin
1-2
Heating and keeping warm
Stew (e.g., lentils)
1-2
Milk**
1.-2.
Sausages heated in water**
3-4
Defrosting and heating
Frozen spinach
3-4
Frozen goulash
3-4
* Uncovered cooking
** Uncovered
*** Turn frequently
12
Power level
Slow cooking, simmering
Potato dumplings*
4.-5.
Fish*
4-5
White sauces (e.g., bechamel)
1-2
Whipped sauces (e.g., Bearnaise, Hollandaise)
3-4
Boiling, steaming, sautéing
Rice (with a double amount of water)
2-3
Rice pudding
1.-2.
Potatoes
4-5
Pasta*
6-7
Soups
3.-4.
Vegetables
2.-3.
Greens, frozen foods
3.-4.
Cooked in a pressure cooker
4.-5.
Stewing
Meat roll
4-5
Stew
4-5
Goulash
3.-4.
Bake / Fry with a little oil**
Steaks, chops (plain or breaded)
6-7
Beefsteak (3 cm thick)
7-8
Chicken breast (2 cm thick)***
5-6
Hamburgers, meatballs (3 cm thick)***
4.-5.
Plain fish and fish fillet
5-6
Breaded fish and fish fillet
6-7
Prawns and shrimps
7-8
Frozen meals (e.g., stir-fries)
6-7
Pancakes
6-7
Omelette
3.-4.
Frying** (150-200 g per serving with 1-2 l. of oil)
Frozen foods (e.g., French fries, chicken nuggets)
8-9
Frozen croquettes
7-8
Meat (e.g., chicken pieces)
6-7
Fish, vegetables or mushrooms, breaded or battered, e.g., baby mushrooms
6-7
Confectionery products (e.g., fritters, fruit in batter)
4-5
* Uncovered cooking
** Uncovered
*** Turn frequently
Childproof lock
The hob can be protected against being accidentally turned on,
to ensure that children do not switch on the hotplates.
Activating and deactivating the childproof
lock
The hob should be turned off.
To activate: press the symbol D for approximately 4 seconds.
The indicator next to the symbol D lights up for 10 seconds.
The hob is locked.
Childproof lock
With this function, the childproof lock automatically activates
when a hob is switched off.
Activating and deactivating
All of the relevant information on the automatic childproof lock
connection can be found in the Basic settings chapter.
To deactivate: press the symbol D for approximately
4 seconds. The lock is now deactivated.
13
Powerboost function
The Powerboost function can be used to heat large amounts of
water more quickly than the power level Š.
All the hotplates have this function.
To deactivate
1. Select a hotplate.
2. Press the symbol boostG.
To activate
The › indicator will no longer appear and the hotplate will
return to the power level Š.
The hob must be switched on, but no hotplate should be
working.
The function will be deactivated.
Note: In certain circumstances, the Powerboost function may
turn off automatically in order to protect the electronic
components inside the hob.
1. Select a hotplate.
2. Press the boostG symbol.
The › indicator lights up
The function should be activated.
Note: If any hotplate is switched on when the Powerboost
function is working, › and Š will flash on the hotplate display;
the power level Š will then be set Š. The Powerboost function
will be deactivated.
Time programming function
This function may be used in two different ways:
■
to automatically switch off a hotplate.
■
as a timer.
Once the time has elapsed
The hotplate switches off. A warning signal sounds. The time
program function lights up ‹‹ for 10 seconds in the display.
When the 0 symbol is pressed, the indications turn off and the
beeping stops.
Turning off a hotplate automatically
The zone turns off automatically once the selected time has
elapsed.
How to program
Notes
To program a cooking time of less than 10 minutes, always
press 0 before selecting the desired value.
■
■
The hob must be switched on:
1. Select the desired hotplate and power level.
2. Press the 0 symbol. The x indicator on the hotplate lights
up. ‹‹ lights up in the time program function display.
3. Within the next 10 seconds, select the desired cooking time
in the programming zone.
■
If cooking times have been programmed for various zones,
the time program function always displays the time of the
selected hotplate.
Cooking times can be programmed for up to 99 minutes.
The timer
The timer can be set for periods of up to 99 minutes. It is
independent of the other settings. This function does not
automatically switch off a hotplate.
How to program
1. Press the 0 symbol until the U indicator lights up. ‹‹ lights
up in the time program function display.
2. Adjust the desired time in the programming zone.
The time starts to count down again after a few seconds.
Changing or cancelling the time
Press the 0 symbol and the U indicator lights up.
The cooking time starts to count down.
Note: The same cooking time can be automatically
programmed for the all the hotplates. The programmed time
passes independently for each of the hotplates.
The Basic settings chapter provides information on
automatically programming the cooking time.
Changing or cancelling the time
Select the hotplate and then press the 0 symbol.
Change the cooking time using the programming zone or set
to ‹‹ in order to cancel the time.
14
Change the cooking time in the programming zone or press 0
to cancel the time.
Once the time has elapsed
Once the time has elapsed, a beep will sound. ‹‹ and U are
displayed in the time program function display. After pressing
the 0 symbol, the indications turn off.
Cleaning lock function
Cleaning the control panel while the hob is switched on may
change the settings.
locked for 35 seconds. The control panel surface can now be
cleaned without the risk of changing the settings.
In order to avoid this, the hob has a cleaning lock function.
Press the > symbol. A signal sounds. The control panel is
Note: The lock does not affect the main switch. The hob may
be turned off when desired.
Automatic time limitation
If the hotplate remains in use for a long time and no changes
are made in the settings, the automatic time limitation function
is triggered.
The hotplate stops heating. The ”, ‰ symbol and the residual
heat indicator œ/• flash alternately in the display.
The indicator goes out when any symbol is pressed. The
hotplate can now be reset.
When the automatic time function is used, it is governed by the
selected power level (from 1 to 10 hours).
Displaying energy consumption
This function displays total energy consumption for the time the
hob has been switched on.
The Basic Settings chapter provides information on activating
this function.
After switching off the hob, the consumption in kWh is
displayed for 10 seconds.
An example is shown in the image with a consumption of
‚.‹‰ kWh.
NZK
Basic settings
The device has several basic settings. These settings may be
adapted to the user's individual needs.
Indicator
Function
™‚
Childproof lock
‹ Deactivated.*
‚ Activated.
™ƒ
Audible signals
‹ Confirmation and error signals deactivated.
‚ Only error signal activated.
ƒ Only confirmation signal activated.
„ All signals activated.*
*Factory settings
**The maximum power of the hob depends on the configuration of the installation's connection current. To not exceed this maximum
value, the hob includes a series of components that automatically control the power, distributing it between the hotplates in use
as required.
15
Indicator
Function
™„
Display energy consumption
‹ Deactivated.*
‚ Activated.
Automatic programming of cooking time.
™†
‹ Switched off.*
‚-ŠŠ Automatic shut-off time.
Duration of the time program function warning signal
™‡
‚ 10 seconds*.
ƒ 30 seconds.
„ 1 minute.
Power-Management function
™ˆ
‹ = Deactivated.*
‚ = 1,000 W. minimum power.
‚= 1,500 W.
ƒ = 2,000 W.
etc.
Š or Š. = maximum power of hob.**
Hotplate time selection
™Š
‹ Unlimited: the last hotplate programmed remains selected.*
‚ Limited: The hotplate will only remain selected for 10 seconds.
Return to basic settings
™‹
‹ Personal settings.*
‚ Return to factory settings.
*Factory settings
**The maximum power of the hob depends on the configuration of the installation's connection current. To not exceed this maximum
value, the hob includes a series of components that automatically control the power, distributing it between the hotplates in use
as required.
Accessing the basic settings
4. Next, select the desired setting in the programming zone.
The hob should be turned off.
1. Switch on the hob using the main switch.
2. Within the next 10 seconds, press and hold the 0 symbol for
4 seconds.
5. Press the 0 symbol for 4 seconds.
The settings should be correctly saved.
Leaving the basic settings
Turn off the hob with the main switch.
In the display, ™ and ‚ alternately light up and ‹ as a default
setting.
3. Press the 0 symbol several times until the desired function
indicator appears.
16
Care and cleaning
The advice and warnings contained in this section aim to guide
you in cleaning and maintaining the hob, so that it is kept in the
best possible condition
Hob
The best way to remove stubborn stains is to use a glass
scraper. Follow the manufacturer's instructions.
Suitable glass scrapers can be obtained through the Technical
Assistance Service or from our online shop.
Hob frame
Cleaning
Clean the hob after each use. This prevents food remains left
on the surface from burning. Wait until the hob is cool enough
before attempting to clean it.
Only use cleaning products specifically designed for hobs.
Follow the instructions provided on the packaging.
Do not use:
■
Undiluted washing-up liquid
■
Dishwasher detergent
■
Abrasive products
■
Corrosive products such as oven sprays or stain removers
■
Sponges that may scratch
■
High-pressure or steam cleaners
In order to avoid damage to the hob frame, follow the
indications below:
■
Use only slightly soapy hot water
■
Do not use sharp or abrasive products
■
Do not use a glass scraper
Fixing malfunctions
Malfunctions are usually due to small details. Before calling the
Technical Assistance Service you should bear in mind the
following advice and warnings.
Indicator
Malfunction
none
The electric power supply has been cut off. Use other electrical appliances to check whether there has been a
power cut.
Solution
The appliance has not been correctly con- Check that the appliance has been connected correctly according
nected following the connection diagram. to the connection diagram.
The indicators
blink
Electronic system malfunction.
If none of the above checks resolve the malfunction, contact the
Technical Assistance Service.
The control panel is damp or an object is
resting on it.
Dry the control panel area or remove the object.
“§ + number / š Electronic system malfunction.
+ number / ¡ +
number
Unplug the hob from the mains. Wait about 30 seconds before
plugging it in again.*
”‹ / ”Š
There is an internal operating error.
Unplug the hob from the mains. Wait about 30 seconds before
plugging it in again.*
”ƒ / ”†
The electronic system has overheated and Wait until the electronic system has cooled down sufficiently. Then
the corresponding hotplate has been
press any symbol on the hob. *
switched off.
”…
The electronic system has overheated and
all hotplates have been switched off.
—‚
Supply voltage outside normal operating
limits.
—ƒ / —„
The hotplate has overheated and has
Wait until the electronic system has cooled down sufficiently before
switched off in order to protect its cooking switching it back on.
surface.
Contact your power company.
* If the warning persists call the Technical Assistance Service.
Do not rest hot pans on the control panel.
17
Normal noise while the appliance is working
A high-pitched whistling sound
Induction heating technology is based on the creation of
electromagnetic fields that generate heat directly at the base of
the pan. Depending on how the pan has been manufactured,
certain noises or vibrations may be produced such as those
described below:
This noise is produced mainly in pans made from different
materials superimposed on one another, and it occurs when
such pans are heated at maximum power on two hotplates at
the same time. The whistling disappears or becomes fainter as
soon as the power level is lowered.
A deep humming sound as in a transformer
Noise from the fan
This noise is produced when cooking on a high power level. It
is caused by the amount of energy transferred from the hob to
the pan. The noise disappears or becomes faint when the
power level is lowered.
A low whistling sound
This noise is produced when the pan is empty. The noise
disappears when water or food is added to the pan.
A crackling sound
This noise occurs in pans which are made from different
materials superimposed on one another. It is caused by the
vibrations that occur in the adjoining surfaces of the different
superimposed materials. The noise comes from the pan. The
amount of food and cooking method can vary noise intensity.
After-sales service
Our after-sales service is there for you if your appliance should
need to be repaired. We are committed fo find the best solution
also in order to avoid an unnecessary call-out.
E number and FD number:
Please quote the E number (product number) and the FD
number (production number) of your appliance when
contacting the after-sales service. The rating plate bearing
these numbers can be found on the appliance certificate.
Please note that a visit from an after-sales service engineer is
not free of charge, even during the warranty period.
Please find the contact data of all countries in the enclosed
customer service list.
To book an engineer visit and product advice
GB
0844 8928979
Calls from a BT landline will be charged at up to 3
pence per minute. A call set-up fee of up to 6 pence may
apply.
IE
01450 2655
Trust the expertise of the manufacturer, and rest assured that
the repair will be carried out by trained service technicians
using original spare parts for your domestic appliance.
18
For proper use of the electronic system, the temperature of the
hob must be controlled. To do this, the hob has a fan which
turns on when a high temperature is detected. The fan may also
work by inertia after the hob has been switched off, if the
temperature detected is still too high.
Rhythmic sounds similar to the hands of a clock
This noise is only produced when 3 or more hotplates are
working and disappears or is reduced when one of the
hotplates is switched off.
The noises described are normal, they are part of induction
heating technology and not a sign of malfunction.
Robert Bosch Hausgeräte GmbH
Carl-Wery-Straße 34
81739 München
Germany
www.bosch-home.com
*9000776807*
9000776807
02
921210