Precision Cooling
For Business-Critical Continuity™
Liebert® XDF™
User Manual - 14kW Nominal Capacity, 60 Hz
DATA CENTER SOLUTIONS
For More Information:
(866) 787-3271
Sales@PTSdcs.com
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.0
GLOSSARY OF SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
2.0
PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2.1
Operational Overview—Liebert XDFS, Self-Contained, Air-Cooled Model . . . . . . . . . . . . . . 3
2.2
Operational Overview - Liebert XDFW, Water/Glycol-Cooled Model . . . . . . . . . . . . . . . . . . . 4
2.3
Operational Overview - Liebert XDFR, Remote Condenser, Air-Cooled Model . . . . . . . . . . . 4
3.0
LIEBERT XDF COMPONENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1
Standard Components—All Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1.1
3.1.2
3.1.3
3.1.4
3.1.5
3.1.6
3.2
Closed-Loop Water System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Drycooler Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Condenser Loop for the Liebert XDFR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.3.1
3.3.2
3.4
11
11
11
11
12
14
Coolant Source—Water/Glycol Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.1
3.2.2
3.3
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enclosure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Side Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmental Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control—Liebert iCOM® Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Variable Frequency Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Liebert Lee-Temp™ Coolant Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Optional Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.4.1
3.4.2
General Enclosure Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Power Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.0
UNCRATING THE LIEBERT XDF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.2
Recommended Setup Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.3
Unloading the Liebert XDF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.3.1
4.3.2
4.3.3
Handling the Unit While It is Packaged . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Unpack the Liebert XDF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Removing the Liebert XDF from Skid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.0
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.1
Liebert XDF Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5.2
Voltage Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5.2.1
5.2.2
5.2.3
5.2.4
Voltage Input Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Uninterruptible Power Supply—Optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert MPH Managed Rack PDUs—Optional. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condensate Drain Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
25
25
25
5.3
Equipment Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.4
Frame and Enclosure Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.4.1
5.4.2
Internal Mounting Rails. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Rear-Mount Rails—Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
i
5.5
Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.6
Door—Remove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.6.1
5.6.2
5.7
Remove the Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Quick Door Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Side Panels—Remove and Replace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.7.1
5.7.2
5.7.3
Remove the Left Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Remove the Right Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Replace a Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.0
DRYCOOLER AND PIPING INSTALLATION—LIEBERT XDFW . . . . . . . . . . . . . . . . . . . . . . . .30
6.1
Drycooler Installation—Water/Glycol-Cooled Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.2
Piping for Liebert XDFW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.2.1
6.2.2
6.2.3
6.2.4
6.3
30
31
31
31
Drycooler Loop System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.3.1
6.4
Closed Loop Water System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Expansion Tanks, Fluid Relief Valves and Other Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Corrosion Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Freeze Protection—Coolant Type and Insulation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glycol Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Filling the Liebert XDFW with Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
6.4.1
6.4.2
6.4.3
Preparing the System for Filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Liebert XDFW Coolant Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Filling the Liebert XDFW with Water or Glycol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.0
CONDENSER INSTALLATION FOR AIR-COOLED UNITS WITH REMOTE CONDENSER . . . . . . . . 34
7.1
Remote Condenser Installation—XDFR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7.2
Condenser Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7.3
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.3.1
7.3.2
7.3.3
Line Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Liebert Lee-Temp/Flood Back Head Pressure Control Condensers . . . . . . . . . . . . . . . . . . . . 36
7.4
Coolant Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
7.5
VFD Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.5.1
7.5.2
7.5.3
7.6
Materials Supplied with Condenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Dehydration/Leak Test and Charging Procedures for VFD Condenser . . . . . . . . . . . . . . . . . 39
Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Liebert Lee-Temp/Flood Back Head Pressure Control Systems . . . . . . . . . . . . . . . . . . . . . . 41
7.6.1
7.6.2
7.6.3
7.6.4
Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Materials Supplied with Condenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dehydration/Leak Test and Charging Procedures for Liebert Lee-Temp Control Type
Condenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
41
42
43
8.0
ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8.1
Utility Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
8.1.1
Route Input Power Cables Through the Liebert XDF’s Top . . . . . . . . . . . . . . . . . . . . . . . . . . 47
ii
9.0
CABLE MANAGEMENT OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
9.1
Cable Management Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
9.2
Cable Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
9.3
Cable Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
9.3.1
Top Cover and Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
9.4
Optional Cable Management Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
10.0
STARTUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
10.1
Liebert XDF Startup Inspection Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
10.1.1 Site Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
10.2
Starting the Liebert XDF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
10.2.1 Evaporator Fan Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
10.2.2 Condenser Fan Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
11.0
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
11.1
Environmental Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
11.2
Liebert iCOM Components and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
11.3
Navigating Through the Liebert iCOM Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
11.3.1 Accessing Menus and Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
11.3.2 Entering the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
11.4
Changing Operational Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
11.5
Changing Liebert iCOM’s Display Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
11.6
Changing the Liebert XDF’s Default Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . 59
11.7
Operation With the Door Open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
11.8
Backup Ventilation System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
11.9
Liebert XDF Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
11.10 Uninterruptible Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
12.0
ALARMS AND WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
12.1
General Alarm Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
12.2
Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
12.2.1 Backup Ventilation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
12.3
Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
13.0
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
13.1
Periodic Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
13.1.1 Maintaining the Self-Contained, Air-Cooled Liebert XDF. . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
13.1.2 Maintaining the Liebert XDF with Remote Condenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
14.0
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
14.1
Optional Power Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
14.2
Optional Managed Power - Liebert MPH Managed Rack PDUs, Horizontal-Mount . . . . . . 69
iii
FIGURES
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Figure 19
Figure 20
Figure 21
Figure 22
Figure 23
Figure 24
Figure 25
Figure 26
Figure 27
Figure 28
Figure 29
Figure 30
Figure 31
Figure 32
Figure 33
Figure 34
Figure 35
Figure 36
Figure 37
Figure 38
Figure 39
Figure 40
Figure 41
Figure 42
Figure 43
Figure 44
Figure 45
Figure 46
Figure 47
Component location, general operational layout of the Liebert XDFS . . . . . . . . . . . . . . . . . . . . . . 3
Component location, general operational layout of the Liebert XDFW . . . . . . . . . . . . . . . . . . . . . . 4
Component location, general operational layout of the Liebert XDFR . . . . . . . . . . . . . . . . . . . . . . 5
Component location, rear of Liebert XDF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Dimensional data, Liebert XDFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Dimensional data, Liebert XDFW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Dimensional data, Liebert XDFR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Dimensional data, all models—top, bottom and cable entry cutouts. . . . . . . . . . . . . . . . . . . . . . . 10
Cooling system components—Liebert XDFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cooling system components—Liebert XDFW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cooling system components—Liebert XDFR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Liebert XDF with Liebert iCOM controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Liebert XDFW supplied by closed-loop water system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Water/glycol-cooled general arrangement with drycooler as coolant source . . . . . . . . . . . . . . . . . 16
Liebert XDFR general arrangement with condenser as coolant source. . . . . . . . . . . . . . . . . . . . . 17
Optional power equipment, examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Recommended unit handling equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Removing Liebert XDF packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Remove lag bolts and brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Roll Liebert XDF off the shipping skid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Liebert XDF clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Alternate condenser fan power connection, Liebert XDFS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Condensate drain connection and adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Recommended equipment arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Removing Liebert XDF door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Condenser planning dimensional data—One-fan units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Typical condenser footprint—dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Piping connection locations for 1-fan VFD control condensers . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Piping connections for 1-fan Liebert Lee-Temp condensers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Air-cooled VFD control, general arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Air-cooled, Liebert Lee-Temp general arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Customer electrical connections and cable entry points—self-contained, air-cooled units . . . . . 45
Customer electrical connections and cable entry points—water/glycol-cooled units and
remote, air-cooled units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Route input power cords through Liebert XDF top. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Cable rings, Velcro straps on Liebert XDF rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Cable Management Channel lengths. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Cable management mounting locations and options: Velcro cable straps, cable spools . . . . . . . . 50
Cable management accessories: Cable Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Liebert iCOM controller keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Liebert iCOM display components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Liebert iCOM graphical display default screen components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Liebert iCOM simple display default screen components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Liebert iCOM user menu, Page 1 of 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Accessing additional menu lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Display setup screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Airflow pattern, backup ventilation operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Liebert XDF model numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
iv
TABLES
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Table 16
Table 17
Table 18
Table 19
Table 20
Table 21
Optional condensate pump performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Water supply flow rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethylene glycol concentrations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glycol supply flow rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drycooler selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Volume in standard Type “L” copper piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Equivalent lengths (feet) for various pipe fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Indoor unit R407C charge, approximate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Line charges - R407C per 100 ft (30 m) of Type “L” copper tube . . . . . . . . . . . . . . . . . . . . . . . . . .
Condenser R407C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Condenser connection sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keyboard icons and functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User menu icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Coolant pressure settings, psi (kPa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total heat rejection—Liebert XDFS only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert XDFR condenser dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS performance data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert MPH—Rack-mount model numbers and specifications. . . . . . . . . . . . . . . . . . . . . . . . . . .
v
25
30
32
32
32
33
38
38
38
38
38
54
58
62
66
67
68
68
68
68
69
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that must be closely followed during installation and
maintenance of this unit to maintain compliance with agency listings. Read all safety and operating
instructions before attempting to operate the Liebert XDF. Adhere to all warnings on the unit and in
this manual. Follow all operating and user instructions.
This product is designed for commercial / industrial use only. This product is not intended for use
with life support or other U.S. FDA designated “critical” devices. Maximum loads must not exceed
those shown on the Liebert XDF’s serial tag.
Install in a clean environment, free from moisture, flammable liquids, gases and corrosive substances.
Operate this product in an indoor environment at an ambient temperature between 35°F and 104°F
(1.6°C to 40°C). Additionally, units using a remote condenser must be operated at outdoor ambient
temperatures: placeholder
• VFD condensers—above 0°F (-18°C)
• Liebert Lee-Temp condensers—above -20°F (-29°C)
This product must be connected to and powered by suitable AC supplies, rated in accordance with the
unit’s serial tag. It must be suitably grounded and protected by circuit breakers or fuses.
Power extension cables, if used, must be rated for the load and must not exceed 20 ft. (6.1m) in length.
Liebert recommends using shielded cables for all external communication interfaces.
Ensure that the Liebert XDF has proper ventilation. Never block or insert objects into the ventilation
holes or other openings. Maintain a minimum clearance of 36 in. (915mm) in front, behind, on the
right side and above the self-contained, air-cooled Liebert XDF for proper airflow and service. The
water/glycol-cooled Liebert XDF and the remote air-cooled Liebert XDF require 36 in. (915mm) clearance in front, behind and on the right side. Neither requires overhead clearance.
1
Glossary of Symbols
1.0
GLOSSARY OF SYMBOLS
Hazardous Voltage Present
Note following instructions
Consult user manual for additional information
Indicates weight
Indicates ground connection
Indicates alternating current
2
Product Description
2.0
PRODUCT DESCRIPTION
Congratulations on purchasing a Liebert XDF. The Liebert XDF is an integrated equipment cabinet
with integral cooling and intelligent control to protect mission-critical enterprise systems from
extreme heat. The Liebert XDF provides an organized, secure, controlled environment for your sensitive electronic equipment. The unit is available in a variety of configurations to suit your electronic
equipment’s environmental requirements.
The Liebert XDF is available in three models:
• Liebert XDFS—Self-Contained, Air-Cooled Model
• Liebert XDFW—Water/Glycol-Cooled Model
• Liebert XDFR—Remote Condenser, Air-Cooled Model
The self-contained, air-cooled Liebert XDFS is intended for installation in open areas. Installation in
closed-in areas, such as in a closet, alcove or similar space, requires field-supplied ducting, an external booster fan and sufficient makeup air. Contact your local Emerson Network Power representative
before installing the Liebert XDFS in an area that might inhibit heat dissipation.
The Liebert XDFW and Liebert XDFR, however may be installed in closed-in areas that meet clearance requirements in the front, rear and right side (see Figures 8 and 21). Heat from the
Liebert XDFW is carried away by the coolant; heat from the Liebert XDFR is rejected at the condenser, which is installed outdoors.
2.1
Operational Overview—Liebert XDFS, Self-Contained, Air-Cooled Model
The self-contained, air-cooled Liebert XDFS employs a compressorized, direct expansion cooling system rated at 14kW to supply cooling air to rack-mounted equipment. A bank of fans circulates this
cooling air through the electronic equipment in the Liebert XDFS (see Figure 1). An evaporator coil
extracts heat from the circulating air. That heat is transferred to a condenser at the top of the Liebert
XDFS and exhausted into the room.
The Liebert XDF’s backup ventilation system operates automatically if power fails or if any
Liebert XDF cooling system component fails.
Figure 1
Component location, general operational layout of the Liebert XDFS
Heated Air
Exhaust
Condenser Coil transfers
heat extracted from
electronic equipment
cabinet to incoming air
Condenser Air
Entry Point
Condenser
Coil - 1 of 2
Condenser Air
Entry Point
Liebert iCOM
Controller
Evaporator Coil
extracts heat from
air circulated through
the rack equipment
compartment
Rack-Mount Equipment
Compartment (isolated
from external air and top
condenser section)
Backup Ventilation
Air Intake
Compressor
Evaporator Fans
circulate cooling air
Front of Liebert XDFS
3
Product Description
2.2
Operational Overview - Liebert XDFW, Water/Glycol-Cooled Model
The water/glycol-cooled Liebert XDFW employs a single-stage cooling system rated at 14kW to supply
cooling air to the rack-mounted equipment. A bank of fans circulates this cooling air through the electronic equipment in the Liebert XDF (see Figure 1).
An evaporator coil extracts heat from the circulating air. That heat is transferred to a brazed plate
condenser at the top of the Liebert XDF, transferred to the cooling water or glycol solution and is
piped out of the unit.
Coolant is piped through the back of the Liebert XDF through supply and return pipes with 1" female
NPT connections (refer to Figure 2 or Figure 8).
The Liebert XDF’s backup ventilation system operates automatically if power fails or if any Liebert
XDF cooling system component fails.
If water is used as the coolant, Liebert recommends employing a closed system connected to an external condensing unit. A closed water supply system protects the Liebert XDF from particles and other
contaminants that might reduce cooling efficiency and damage the Liebert XDF.
Figure 2
Component location, general operational layout of the Liebert XDFW
Brazed Plate Condenser
(behind grille)
Coolant Return - in rear
Liebert iCOM
Controller
Coolant Supply - in rear
Evaporator Coil
extracts heat from
air circulated
through
the rack equipment
compartment
Rack-Mount
Equipment
Compartment
(isolated from
external air)
Backup Ventilation
Air Intake
Compressor
Front of Liebert XDFW
2.3
Evaporator Fans
circulate cooling air
Operational Overview - Liebert XDFR, Remote Condenser, Air-Cooled Model
The Liebert XDFR remote condenser, air-cooled model employs a single-stage cooling system rated at
14kW to supply cooling air to the rack-mounted equipment. A bank of fans circulates this cooling air
through the electronic equipment in the Liebert XDF (see Figure 1).
The Liebert XDFR transfers the heat captured by the evaporator coil to a fin-tube condenser outdoors
where it dissipates.
The backup ventilation system in each model of the Liebert XDF operates automatically if power fails
or if any Liebert XDF cooling system component fails.
4
Product Description
Figure 3
Component location, general operational layout of the Liebert XDFR
Hot Gas Line
Connection - in rear
Liebert iCOM
Controller
Liquid Line
Connection- in rear
Evaporator Coil
extracts heat from
air circulated through
the rack equipment
compartment
Rack-Mount
Equipment
Compartment
(isolated from
external air)
Backup Ventilation
Air Intake
Compressor
Front of Liebert XDFR
Evaporator Fans
circulate cooling air
5
Product Description
Figure 4
Component location, rear of Liebert XDF
Condenser fan
(removable to reduce
height temporarily)
SELF-CONTAINED
AIR COOLED MODEL
Condenser air intakes,
perforated grilles
Door handle
Backup ventilation
damper (air exit)
Rear door
Service access for gauges
to be inserted for testing
Condensate drain
Three-phase electrical
cord, 10 feet (3m)
Single-phase electrical cord,
10 feet (3m)
Casters
Stabilizing foot
(one of four)
WATER/GLYCOL COOLED and
REMOTE, AIR CONDENSER MODELS
Return Line (1" female, NPT)
Water/Glycol Cooled Models
Supply Line (1" female, NPT)
Water/Glycol Cooled Models
Hot Gas Line (7/8" O.D. Copper Tube)
Remote, Air Condenser Models
Liquid Line (5/8" O.D.
Copper Tube)
Remote, Air Condenser
Models
Backup ventilation
damper (air exit)
Door handle
Rear door
Service access for
gauges to be inserted
for testing
Condensate drain
Three-phase electrical
cord, 10 feet (3m)
Single-phase electrical cord,
10 feet (3m)
Casters
6
Stabilizing foot
(one of four)
Product Description
Figure 5
Dimensional data, Liebert XDFS
34-1/8"
(867mm)
Rack Section
24-1/8"
(613mm)
2-1/2"
(64mm)
82-1/4"
(2089mm)
36U
Control
Side
79-3/4"
(2026mm)
LEFT SIDE
49-1/2" (1257mm)
FRONT
2-5/8"
(68mm)
24-3/8" to 32-11/32"
(620-821mm)
mounting depth
Cooling Section
9-5/16" (252mm)
Single-Phase Power Cord
Entrance ; factory-supplied,
10' (3m) NEMA 5-15P
3-Phase Power Cord
Entrance ; factory-supplied,
10' (3m) NEMA L21-30P
Capped Service
Gauge Access
45-3/4"
(1162mm)
Backup
Ventilation
Air Outlet
4-1/2"
(114mm)
Cover
Plate
DETAIL A
MGH Threaded 3/4"
Condensate Drain Connection
7
Detail
Area
“A”
REAR VIEW
Product Description
Figure 6
Dimensional data, Liebert XDFW
Rack Section
24-1/8"
(613mm)
Cooling Section
9-5/16" (252mm)
Coolant Return
Line Entrance
5-1/2"
(140mm)
6-15/16"
(176mm)
1-7/8"
(48mm)
7"
(177mm)
Control
Side
79-3/4"
(2026mm)
45-3/4"
(1162mm)
Backup
Ventilation
Air Outlet
2-5/8"
(68mm)
FRONT
4-1/2"
(114mm)
Detail
Area
“A”
REAR VIEW
Single-Phase Power Cord
Entrance ; factory-supplied,
10' (3m) NEMA 5-15P
3-Phase Power Cord
Entrance ; factory-supplied,
10' (3m) NEMA L21-30P
42U
LEFT SIDE
Capped Service
Gauge Access
24-3/8" to 32-11/32"
(620-821mm)
mounting depth
Cover
Plate
DETAIL A
49-1/2" (1257mm)
8
MGH Threaded 3/4"
Condensate Drain Connection
Coolant
Supply
Line
Entrance
Product Description
Figure 7
Dimensional data, Liebert XDFR
Rack Section
24-1/8"
(613mm)
Cooling Section
9-5/16" (252mm)
Coolant Return
Line Entrance
6"
(152mm)
7"
(178mm)
1-7/8"
(48mm)
Coolant
Supply
Line
Entrance
7"
(177mm)
Control
Side
79-3/4"
(2026mm)
45-3/4"
(1162mm)
Backup
Ventilation
Air Outlet
2-5/8"
(68mm)
FRONT
4-1/2"
(114mm)
Detail
Area
“A”
REAR VIEW
Single-Phase Power Cord
Entrance ; factory-supplied,
10' (3m) NEMA 5-15P
3-Phase Power Cord
Entrance ; factory-supplied,
10' (3m) NEMA L21-30P
42U
Capped Service
Gauge Access
LEFT SIDE
24-3/8" to 32-11/32"
(620-821mm)
mounting depth
Cover
Plate
DETAIL A
49-1/2" (1257mm)
9
MGH Threaded 3/4"
Condensate Drain Connection
Product Description
Figure 8
Dimensional data, all models—top, bottom and cable entry cutouts
4-1/2"
(114mm)
BOTTOM VIEW
Front
TOP VIEW
A
4-3/8"
(112mm)
15"
(381mm)
Cable
Entry
Cutouts
10-3/4"
(273mm)
B
10-1/4"
(260mm)
4"
(102mm)
4-1/2"
(114mm)
Cable Entry Cutout
Stabilizing Foot,
1 of 4
Front
Self-contained, air-cooled model shown; dimensions
for water-cooled and remote, air-cooled units are identical;
neither the water-cooled unit nor the remote, air-cooled unit
has a condenser fan.
10
Caster, 1 of 4
A - Rack-Mount Width
EIA Nominal: 19" (483mm)
Inside Dimension: 17-13/16" (452mm)
B - Adjustable Mounting Depth
Minimum: 24" (620mm)
Maximum: 32-11/32" (821mm)
Liebert XDF Components
3.0
LIEBERT XDF COMPONENTS
3.1
Standard Components—All Models
3.1.1
Frame
Height
• Liebert XDFS—82-1/4 inches (2089mm)
• Liebert XDFW—79-3/4 (2026)
• Liebert XDFR—79-3/4 (2026)
Usable Rack Height
• Liebert XDFS—36U (63 inches)
• Liebert XDFW—42U (73-1/2 inches)
• Liebert XDFR—42U (73-1/2 inches)
EIA Rack Width
• All Models—19 inches (483mm)
Each type of the Liebert XDF has a frame consisting of heavy-duty, riveted, 12-gauge steel. Each has
fixed front rails and adjustable rear rails with square holes for installing rack-mount equipment. The
front and rear vertical frame members accommodate internal mounting rail options and provide
space to route and manage cabling.
Cutouts in the top (front and rear) permit customer cable entry (Figure 8). All units have casters,
stabilizing feet and a grounding lug.
3.1.2
Enclosure
The Liebert XDF is equipped with seals to maintain a separate air volume inside the equipment compartment.
NOTE
Preventing air infiltration into the Liebert XDF will significantly improve overall performance
and reduce the amount of condensate generated. Ensure that all cable entrances are sealed and
that doors are closed securely. Check to ensure that all panels are properly installed; this is
especially important if panels have been removed in the field.
3.1.3
Doors
The front and rear doors are framed from sheet metal and are removable. A multi-point latch with
key lock is provided for security. The front door may be either solid sheet metal or have a Plexiglas™
window for viewing installed equipment. The rear door is solid, full-height sheet metal.
3.1.4
Side Panels
Side panels are constructed of sheet metal and use special fasteners to permit removal for maintenance. Insulation is included to provide improved thermal and sound insulation, as well as to prevent
condensate formation on the outside of the unit.
11
Liebert XDF Components
3.1.5
Environmental Control
The Liebert XDF supplies cooling air—68°F to 77°F (20-25°C)—to electronic equipment in the rackmount equipment compartment.
In normal operation, six fans at the right front corner of the Liebert XDF circulate cooling air through
the equipment compartment. The laterally circulating air absorbs heat generated by the electronic
equipment and transfers the heat to an evaporator coil at the right rear of the Liebert XDF. The heat
is removed differently in each type of unit.
Heat Removal—Self-Contained, Air-Cooled Liebert XDFS
Heat removed from the Liebert XDFS cabinet is transferred to condenser coils at the top of the Liebert XDF, in a section separated from the equipment compartment. The condenser fan on top of the
self-contained, air-cooled Liebert XDF draws ambient air through the condenser coils and exhausts
the heat-laden air into the room.
Heat Removal—Water/Glycol-Cooled Liebert XDFW
The Liebert XDFW transfers the heat captured by the evaporator coil to a brazed plate condenser at
the top of the unit, also separate from the equipment compartment. That heat is then carried away by
the cooling water or glycol to a condenser or drycooler.
Heat Removal—Remote Condenser, Air-Cooled Liebert XDFR
The Liebert XDFR transfers the heat captured by the evaporator coil to a fin-tube condenser outdoors
where it dissipates.
Figure 9
Cooling system components—Liebert XDFS
Condenser Fan
Condenser Coil
Condenser Air
Intake Vent for
Normal Operation
Backup Ventilation
Intake Vent (exhaust
vent is on rear)
Evaporator Coil
(behind damper)
extracts heat from
circulated air
Front
Rear
12
Liebert XDF Components
Figure 10 Cooling system components—Liebert XDFW
Coolant
Return
Connection
Brazed Plate
Condenser
Coolant Supply
Connection
Backup Ventilation
Intake Vent
(exhaust vent
is on rear)
Evaporator Coil
(behind damper)
extracts heat from
circulated air
Front
Rear
Figure 11 Cooling system components—Liebert XDFR
Coolant
Return
Connection
Liquid Line
Connection
Backup Ventilation
Intake Vent (exhaust
vent is on rear)
Evaporator Coil
(behind damper)
extracts heat from
circulated air
Front
Rear
13
Liebert XDF Components
3.1.6
Control—Liebert iCOM® Controller
Each model of the Liebert XDF is equipped with Liebert’s iCOM controller for all programming functions. The menu-driven, 128 x 64 dot matrix graphic display shows the status of the conditioned
space, setpoints, alarm status and settings, event histories and the time.
Refer to 11.2 - Liebert iCOM Components and Functions and 11.3 - Navigating Through the
Liebert iCOM Display for details or call 800-543-2778.
Figure 12 Liebert XDF with Liebert iCOM controller
Liebert iCOM controller
14
Liebert XDF Components
3.2
Coolant Source—Water/Glycol Models
The Liebert XDFW may be connected to either of two types of coolant sources:
• a closed-loop water system (cooling tower)
• a drycooler loop
3.2.1
Closed-Loop Water System
A closed water supply system is required for efficiency and to protect the Liebert XDFW from particles and other contaminants that might obstruct the system’s piping.
NOTICE
Risk of dirt and debris contamination. May cause condenser clogging.
Do not install the Liebert XDFW on an open-loop water supply system. Debris carried by the
fluid will clog the Liebert XDFW’s brazed plate condenser.
Figure 13 Liebert XDFW supplied by closed-loop water system
Closed-Loop
Water System
Liebert XDF
Supply Line
Liebert XDF
Return Line
15
Hose Bibs
Install a
field-supplied,
cleanable
60-mesh filter
on the supply
line to prevent
debris from
entering the
Liebert XDF.
Liebert XDF Components
3.2.2
Drycooler Loop
The Liebert XDFW requires an external supply of coolant, either water or glycol, to remove heat
extracted from the Liebert XDF.
Contact the factory for drycooler requirements when connecting multiple Liebert XDFW units. For
information on setting up a drycooler system, contact your local Emerson representative.
Figure 14 Water/glycol-cooled general arrangement with drycooler as coolant source
Expansion Tank
(install at highest
point in system)
Supply
Line
Drycooler
Pump
XDF
Water/Glycol
Cooled
3.3
Return Line
Condenser Loop for the Liebert XDFR
The Liebert XDFR requires connection to an outdoor condenser to remove heat extracted from the
cabinet. The Liebert condenser is low-profile, direct-drive propeller fan-type, air-cooled unit suitable
for mounting outdoors. It provides for the heat rejection of either one or two separate refrigeration circuits, matching heat rejection capacity varying with the outdoor ambient temperatures and with each
corresponding compressor’s heat rejection requirements. Constructed with an aluminum cabinet and
a copper- tube aluminum fin coil, the unit is quiet and corrosion-resistant. The condenser is quickly
and easily installed because all internal wiring is completed at the factory with only external electrical connections to be made at the job site. All electrical connections and controls are enclosed in an
integral weatherproof section of the condenser.
3.3.1
Variable Frequency Drive
The VFD condenser control system utilizes a variable frequency drive, inverter duty fan motor operating from 0% to 100% motor RPM based on head pressure, sensed by coolant pressure transducers.
VFD, ambient-temperature thermostat(s), motor overload protection and electrical control circuit are
factory-wired in the integral control panel. VFD controls the fan adjacent to the connection end of the
condenser and remains energized with active compressor operation. The balance of fans on multi-fan
units cycle on ambient thermostats. This system provides coolant head pressure control for outdoor
ambients as low as 0°F (-18°C).
16
Liebert XDF Components
3.3.2
Liebert Lee-Temp™ Coolant Control
The Liebert Lee-Temp head pressure control system is designed to maintain proper operating head
pressures in outdoor temperatures down to -20°F (-29°C) with the Liebert XDFR. The condensers utilize head pressure control valves, extra coolant and insulated coolant receivers with heater pads. It
works by flooding the condenser coil with liquid coolant to a level that balances the system condensing requirements with the condenser coil surface available to reject the system heat.
During the summer, the system requires the entire condenser coil surface for heat rejection and most
of the coolant is stored in a receiver. In the winter, the same amount of heat can be rejected by only a
fraction of the coil surface. As head pressure begins to fall, the control valve restricts the flow of liquid
coolant exiting from the condenser. This extra liquid coolant reduces the effective condenser surface
area available for heat transfer. The head pressure control valve also bypasses hot gas into the
receiver to warm the liquid and maintain liquid pressure for proper operation of the expansion valve.
Condenser fan controls either cycle the fans based on the ambient temperature or on constantly.
Contact the factory for condenser requirements when connecting multiple Liebert XDFR units. For
information on setting up a condenser system, contact your local Emerson representative.
Figure 15 Liebert XDFR general arrangement with condenser as coolant source
Install traps in the hot gas line on vertical
risers at the base and every 25 feet (7.6m)
in elevation. These traps will collect
condensed refrigerant and refrigerant oil
while the unit is Off to ensure flow of
refrigerant oil during operation.
Condenser
Hot Gas
Line
Liquid Line
XDF
Remote, Air-Cooled
3.4
Optional Equipment
3.4.1
General Enclosure Options
•
•
•
•
•
•
•
•
•
•
•
Sealed entrance cable bundle
Cable tray
Cable Management Channels
Cable rings
Velcro cable management straps
Fixed shelves, vented, 250lb (113kg) capacity
Pullout shelves, vented, 130lb (59kg) capacity
Fixed rails, 150lb (68kg) capacity
Internal keyboard tray
Mounting clip nuts and screws 10-32 or M6 thread
Condensate Pump
17
Liebert XDF Components
3.4.2
Power Options
Liebert MPH Managed Rack PDUs
Power distribution to equipment in your Liebert XDF may be eased with optional Liebert MPH Managed Rack PDUs. These are available in single-phase power option; some units offer remote monitoring and individual receptacle control. For details, see Table 21 - Liebert MPH—Rack-mount
model numbers and specifications or refer to the Liebert MPH Managed Rack PDU user manual,
SL-20827.
Uninterruptible Power Supply
An Uninterruptible Power Supply (UPS) can provide your electronic equipment with surge protection
and suppression, as well as voltage and frequency regulation, preventing damage to the hardware. A
UPS provides time to perform a controlled shutdown of your operating system, allowing you to save
valuable data. Liebert online, double-conversion UPS systems also condition utility power, eliminating damaging power transients.
The following Liebert UPS models are available for installation in the Liebert XDF:
On-Line UPS Systems
• Liebert GXT3 - 500, 700, 1000, 1500, 2000, 2700 and 3000RT120
Line Interactive Systems
• Liebert PS1000, 1440, 2200 and 3000RT3-120
Refer to the UPS user manual for further details.
Figure 16 Optional power equipment, examples
Liebert
UPStation GXT
–+
A C INPUT
18
B A TTE R Y
UPS ON
BY PASS
Liebert GXT3U UPS
and Additional Battery
Cabinet
Uncrating the Liebert XDF
4.0
UNCRATING THE LIEBERT XDF
4.1
Inspection
Upon arrival of the unit, and before unpacking it, verify that the delivered equipment matches the bill
of lading. Examine the packaging for any signs of mishandling or damage. Inspect all items for damage, visible or concealed. Report any damage immediately to the carrier and file a damage claim. Send
a copy to Liebert Corporation or to your sales representative.
Packing Material
All material used to package this unit is recyclable. Please save the material for future use or dispose
of it appropriately.
4.2
Recommended Setup Equipment
• pallet jack or forklift
• utility knife
• 3/8" ratchet or wrench
4.3
Unloading the Liebert XDF
! WARNING
Risk of top-heavy unit falling over. Can cause death, injury and equipment damage.
Read all of the following instructions before attempting to move, lift or remove packaging
from the unit.
! CAUTION
Risk of sharp edges, splinters and exposed fasteners. Can cause personal injury.
Only trained personnel wearing appropriate safety headgear, gloves, shoes and glasses should
attempt to move, lift or remove packaging from the unit or prepare the unit for installation.
! CAUTION
Risk of overhead interference. Can damage the unit and structure.
The unit may be too tall to fit through a doorway while on the skid. Measure the unit and
doorway heights and refer to the installation plans to verify clearances before moving the
unit.
! CAUTION
Risk of frozen fluids. Can cause equipment damage.
Keep the unit upright, indoors and protected from dampness, freezing temperatures and
contact damage.
19
Uncrating the Liebert XDF
4.3.1
Handling the Unit While It is Packaged
• If possible, transport the Liebert XDF using a forklift or pallet jack. Otherwise use a crane with
belts or cables and spreader bars to protect the Liebert XDF’s sides from damage.
• If using a forklift or pallet jack, make sure the forks (if adjustable) are spread to the widest distance that fit under the skid. Also, ensure the fork length is suitable for the unit length.
• When moving the packaged Liebert XDF, do not lift it any higher than 6" (152mm) off the ground.
Exercise great care if the Liebert XDF must be lifted higher than 6" (152mm); any personnel not
directly involved in lifting the Liebert XDF must be at least 20' (5m) from the unit.
Figure 17 Recommended unit handling equipment
Forklift
4.3.2
Pallet Jack
Unpack the Liebert XDF
1. Remove the exterior stretch-wrap packaging material from around the Liebert XDF, exposing the
protective corner and side packaging planks (see Figure 18).
2. Remove the corner and side packaging planks from the Liebert XDF, exposing the bag over the
unit.
The bag may remain in place to protect the Liebert XDF from dust and scratches or removed for
immediate unit installation.
Ensure the metal ramps stay with the Liebert XDF for removal from the skid.
3. Remove the bag from the Liebert XDF when ready to remove the skid and install the unit.
Figure 18 Removing Liebert XDF packaging
Self-contained, air-cooled unit shown;
steps apply to all XDF units
1. Remove the exterior
stretch-wrap packaging
2. Remove the corner and
side packaging planks
3. Remove the bag
20
Uncrating the Liebert XDF
4.3.3
Removing the Liebert XDF from Skid
This unit is on casters—to prevent it from rolling, ensure that the skid is on a flat surface before
removing the Liebert XDF from the skid.
1.
2.
3.
4.
5.
6.
Remove eight lag bolts from the unit tie-down brackets on the controls side of the unit.
Remove the four tie-down brackets from the controls side of the unit (see Figure 19).
Find the ramps that were shipped with the unit.
Insert the two tabs on each ramp into the holes on the skid.
Remove eight lag bolts from the unit tie-down brackets on the side opposite the controls.
Remove the four tie-down brackets from the side opposite the controls.
Unit weight when empty is 710 lb (322kg). Weight may differ if optional equipment has been
installed. Refer to the packing slip for the unit’s exact weight.
7. Remove the Liebert XDF by rolling it off of the ramp using an appropriate number of personnel
and rigging based on the unit weight (see Figure 20).
Once off of the skid, the unit can be rolled to the installation site.
NOTE
If the self-contained, air-cooled Liebert XDF is too tall to pass through a doorway, the
condenser fan assembly may be removed, reducing the height by 2-1/2" (64mm).
Figure 19 Remove lag bolts and brackets
Right front corner detail
(controls side of Liebert XDF)
Four (4) Lag Bolts and Two Brackets Per Corner
21
Uncrating the Liebert XDF
Figure 20 Roll Liebert XDF off the shipping skid
Appropriate number of
workers roll Liebert XDF ...
Fit tabs on ramps
into holes on
front of skid
Self-contained, air-cooled unit shown;
steps apply to all XDF units
... off the skid onto level surface
and roll unit to installation location
22
Installation
5.0
INSTALLATION
5.1
Liebert XDF Site Preparation
When deciding where to place your Liebert XDF, keep in mind these factors:
• electricity is required to operate the compressor (208V-3ph-60Hz) and the controls and evaporator
fans (120V-1ph-60Hz)
• adequate ventilation and makeup air are necessary for proper equipment operation and protection
• service clearance must be provided
• the Liebert XDF must be on a level surface to ensure proper operation
• condensate must be drained, either by gravity-fed drain or optional condensate pump
• Liebert XDFW (water/glycol-cooled) units require connection to a water or drycooler loop
• Liebert XDFR (remote condenser, air-cooled) models must be installed where piping and control
wiring can be run from the indoor Liebert XDFR to an outdoor condenser
The Liebert XDFS (self-contained, air-cooled) is intended for installation in open areas. Field-supplied
ducting, an external booster fan and sufficient makeup air are required for installing a self-contained,
air-cooled model in closed-in areas, such as in a closet or alcove. Contact your local Emerson representative before installing the Liebert XDF in an area that might inhibit heat dissipation.
Note the dimensions of your Liebert XDF to determine the space required for proper installation and
operation. All models of the Liebert XDF require 36 in. (915mm) clearance in the front, back and right
side for equipment access and service (see Figure 21). The Liebert XDFS also requires overhead
clearance of 36 in. (915mm).
Figure 21 Liebert XDF clearances
Ceiling
36" (915mm)
Liebert XDFS only
Liebert XDFS (self-contained, air-cooled)
model shown. All units require 36" (916mm)
clearance on the side, front and rear.
The Liebert XDFS requires overhead
clearance of 36" (916mm). Neither the
Liebert XDFW (water/glycol) nor the Liebert
XDFR (remote, air-cooled) requires
overhead clearance.
E merson
Network Power
36"
(915mm)
36"
(915mm)
36"
(915mm)
23
Installation
5.2
Voltage Requirements
All Liebert XDF systems require two input power circuits. Each power cord is 10 feet (3m) long. For the
full load amp requirements of each option, refer to 14.1 - Optional Power Systems or the component’s
user manual.
5.2.1
Voltage Input Requirements
The first input connection provides power—120V-1ph-60Hz, line-to-neutral—to the controls, evaporator fans and condenser fan. This input’s power cord has a NEMA 5-15P plug. This power cord should
be connected to a UPS-protected power source.
The second input connection on 60Hz Liebert XDF units provides power—208V-3ph-60Hz, with neutral—to the compressor, optional condensate pump and an alternate connection for the condenser fan.
(The alternate connection for the condenser fan permits reducing the load on the UPS-protected
power source.) The 208V power cord has a NEMA L21-30P locking plug.
Changing Condenser Fan Power Source—Liebert XDFS
! WARNING
Risk of electric shock. Can cause injury or death.
Disconnect all local and remote electric power before working within and/or installing
equipment.
To change the power source for the Liebert XDFS fan connections:
1. Open the front door panel and look for two screws with Torx heads that secure the hinged corner
panel. The Torx-head screws are on the front doorjamb.
2. Extract the two screws and swing the panel open.
3. Remove the protective covering over the electrical connections (see Figure 22). The cover is
secured with two screws.
4. Find the connectors (see Figure 22) and pull apart the snap connection made at the factory.
5. Connect the alternate power source connector to the supply that feeds the condenser fan.
6. Reinstall the protective cover over the electrical connections.
7. Close the outer panel and reinsert the two Torx screws.
8. Close the front door.
Figure 22 Alternate condenser fan power connection, Liebert XDFS
Power supply
to condenser fan
Default circuit connector
(connection made
at factory)
Protective cover
over high voltage
electrical
connections
Alternate circuit
connector to
condenser fan
24
Installation
5.2.2
Uninterruptible Power Supply—Optional
If your Liebert XDF is equipped with a UPS, it will require connection to a dedicated electrical circuit.
Review the UPS’s user manual before connecting utility power to the unit.
5.2.3
Liebert MPH Managed Rack PDUs—Optional
Liebert MPH Managed Rack PDUs are available in several power ranges. Consult Table 21 in 14.0 Specifications or the Liebert MPH Managed Rack PDU user manual, SL-20827, for your model’s
power requirements.
5.2.4
Condensate Drain Connection
The Liebert XDF cooling process removes humidity from the air inside the cabinet. The moisture is
collected in a pan and must be removed from the cabinet. The condensate may be fed into a gravity
drain or pumped away with an optional, factory-installed condensate pump.
The gravity-fed drain line must be pitched a minimum of 1/8" per foot (11mm per meter).
Table 1
Optional condensate pump performance
Model
Maximum Head,
feet (m)
60Hz
18 (5.49)
50Hz
14 (4.27)
The standard Liebert XDF condensate drain is a 1/2" NPT female pipe connector. A factory-supplied
adapter permits connecting a 3/4" hose, the same size as a standard garden hose. The adapter is
shipped with the cabinet (see Figure 23).
Figure 23 Condensate drain connection and adapter
Condensate Drain Connection
1/2” NPT female connector
or 3/4” garden hose with
adapter (as shipped)
Bottom Right Rear Corner of XDF
25
Installation
5.3
Equipment Layout
! WARNING
Risk of electric shock. Can cause injury or death.
Disconnect all local and remote electric power before working within and/or installing
equipment.
Before installing or rearranging equipment, ensure the equipment and the UPS are switched
Off. Ensure that all electrical sources are disconnected.
The lateral, circular flow of cooling air permits arranging equipment as required for stability if the
Liebert XDF is filled or nearly filled with equipment. Install heavier equipment first, placing it in the
lower racks of the Liebert XDF. This keeps the Liebert XDF from having a high center of gravity,
which could make it easier to tip over (see Figure 24).
The Liebert XDF may be filled to capacity as long as the maximum heat load of 14kW is not exceeded.
If the Liebert XDF will not be filled with equipment, install the equipment to include a 1U space
above and below each unit. Again, install heavier equipment first, placing it in the bottom racks.
After all equipment has been installed, any remaining spaces larger than 5U at the top of the Liebert
XDF should be closed with optional blanking panels. (Panels are available in 1U, 2U, 3U, 4U, 5U and
10U.) This arrangement prevents large, open expanses in the equipment compartment that would
reduce cooling efficiency by channeling airflow around the electronic gear.
Figure 24 Recommended equipment arrangement
Blanking Panels
in empty spaces
larger than 5U
Large expanses
channel airflow
around equipment
Equipment spaced
1U apart
INEFFICIENT SPACING
Irregular equipment spacing
prevents proper airflow for
cooling.
Heavier equipment too high
for best stability
RECOMMENDED SPACING
Regular spacing of equipment
1U apart and blanking panels
enhance distribution of
cooling air.
Heavier equipment at bottom
promotes stability
! CAUTION
Risk of top-heavy unit falling over. Can cause death, injury and equipment damage.
Read all of the following instructions before attempting to move, lift or remove packaging
from the unit.
NOTE
All electrical receptacles and sockets in the vicinity of where the Liebert XDF will be used
must be ground/earth type.
26
Installation
5.4
Frame and Enclosure Configurations
5.4.1
Internal Mounting Rails
The Liebert XDF can accommodate rack-mounted or free-standing computer and network equipment.
The unit features 19-inch (483mm) rear-mount rack rails. These internal mounting rails are designed
in accordance with the EIA 310D rack standard. The rails are adjustable for equipment of different
sizes.
Liebert offers these optional mounting hardware kits: fixed shelf, fixed rails, pullout shelf, 19-inch
(483mm) rack rail adapters and keyboard trays. Each kit includes installation hardware.
5.4.2
Rear-Mount Rails—Position
The Liebert XDF’s front rails are fixed into position, while rear-mount rails
are secured by carriage bolts that pass through horizontal slots in the frame.
These slots permit you to change the front-to-rear distance between the rails
as your application requires.
To position the rails:
1.
2.
3.
4.
5.
6.
Determine the proper location of the rails.
Loosen the bolts securing a rail to the frame.
Move the rail to the desired position (be sure to get the rail square).
Tighten the bolts securing the rails to the frame.
Repeat for the other rail.
Install your rack-mounted equipment or the shelves to hold your freestanding equipment.
NOTE
Before installing any electrical equipment, make sure that the
equipment is switched Off.
5.5
Mounting Hardware
Optional mounting clip nuts and screws are available for mounting equipment
to the mounting rails. Clip nuts are metal clips with captive nuts that fit over
vertical rack rail holes, allowing individual placement of the mounting hardware. Each clip nut and screw package includes 10 clip nuts (Type 10/32 or
M6 threads) and screws.
Detail of Rack Rail
27
Installation
5.6
Door—Remove
The Liebert XDF’s doors are removable for convenience when installing equipment.
5.6.1
Remove the Door
1.
2.
3.
4.
Remove the bolts securing the lower half of each two-piece hinge to the door.
Remove the lower half of each hinge.
Lift the door straight up until the pins clear the hinges.
Set the door in a safe place.
Figure 25 Removing Liebert XDF door
Cabinet
Door
Remove
this bolt
on the
door first
5.6.2
Quick Door Removal
For minimum-security installations that also require frequent and fast removal of the door, the lower
half of the hinge assembly may be permanently removed. This allows for quick removal of an open
door by lifting the door straight up until the pins clear the hinge mount.
5.7
Side Panels—Remove and Replace
Liebert XDF side panels are simple to remove and replace, making it easier to install equipment and
to service the Liebert XDF. Panel removal also improves access for equipment maintenance and
replacement.
28
Installation
5.7.1
Remove the Left Panel
! WARNING
Risk of electric shock. Can cause injury or death.
Disconnect all local and remote electric power before working within and/or installing
equipment.
To remove the left panel from the Liebert XDF:
1. The left panel is secured with two internal security quarter-turn fasteners and four panel
retainers. Open the doors and locate the internal security quarter-turn fasteners on the left side
panel. The security fasteners are at the top front and top rear corners of the panel.
2. Using the factory-supplied T-handle Allen wrench, turn the internal security fasteners
counterclockwise 90 degrees.
3. Locate the four panel retainers on the outside of the left Liebert XDF panel. One retainer is in
each corner of the panel.
4. Using the factory-supplied T-handle Allen wrench, turn the panel retainers counterclockwise
90 degrees.
! CAUTION
Risk of heavy panel falling off. Can cause injury and/or equipment damage.
Support the panel when removing it. Unlocking the security fasteners and removing the panel
retainers will allow unsupported panel to fall.
5. Lift the panel off the lip at the bottom of the Liebert XDF and set it in a safe location.
5.7.2
Remove the Right Panel
! WARNING
Risk of electric shock. Can cause injury or death.
Disconnect all local and remote electric power before working within and/or installing
equipment.
To remove the right panel from the Liebert XDF:
1. Locate the four panel retainers on the outside of the right Liebert XDF panel. One retainer is in
each corner of the panel.
2. Using the factory-supplied T-handle Allen wrench, turn the panel retainers counterclockwise
90 degrees.
! CAUTION
Risk of heavy panel falling off. Can cause injury and/or equipment damage.
Support the panel when removing it. Unlocking the security fasteners and removing the panel
retainers will allow unsupported panel to fall.
3. Lift the panel off the lip at the bottom of the Liebert XDF and set it in a safe location.
5.7.3
Replace a Panel
1. Set the panel on the lip at the bottom of the Liebert XDF frame.
2. Using the factory-supplied T-handle Allen wrench, turn each of the four panel retainers clockwise
90 degrees.
3. Left panel only: Using the factory-supplied T-handle Allen wrench, turn the internal security
fasteners clockwise 90 degrees.
29
Drycooler and Piping Installation—Liebert XDFW
6.0
DRYCOOLER AND PIPING INSTALLATION—LIEBERT XDFW
Equipment damage and personal injury can result from improper piping installation, leak checking,
fluid chemistry and fluid maintenance.
• Follow local piping codes, safety codes and Liebert unit installation and maintenance instructions.
• Qualified personnel must install and inspect system piping.
• Contact a local water consultant regarding water quality, corrosion protection and freeze protection requirements.
! CAUTION
Risk of dirt and debris contamination. May cause condenser clogging.
Do not install a Liebert XDFW on an open-loop water supply system. Debris carried by the
fluid will clog the unit’s brazed plate condenser.
! CAUTION
Risk of piping stress. Can cause leaks and equipment damage.
To help prevent piping failures, supply and return lines must be supported so that their
weight does not bear on the Liebert XDFW’s piping, on the drycooler or on the pumps.
6.1
Drycooler Installation—Water/Glycol-Cooled Model
For details on installing the drycooler, refer to the drycooler’s installation manual or contact your
local Emerson Network Power representative. The manual was shipped with the unit and is available
at the Liebert Web site: www.liebert.com
6.2
Piping for Liebert XDFW
The Liebert XDFW’s supply and return fittings are on the upper portion of the rear of the unit (see
Figure 8). The 1-1/8" diameter pipes have one-inch female NPT fittings. The pipes are capped at the
factory. Piping connections to the Liebert XDFW should be done by properly trained and qualified
personnel. All work must be done in compliance with all national and local regulations.
6.2.1
Closed Loop Water System
Where water will be used as a coolant medium, Liebert recommends use of a closed-loop water system
with a cooling tower or similar heat dissipation method. For flow rates for the Liebert XDFW, see
Table 2.
Table 2
Water supply flow rates
Entering Water
Temp. (EWT), °F (C)
Saturated Cond.
Temp. (SCT), °F (C)
Flow Rate
GPM (l/s)
Pressure Drop
ft (kPa)
65 (18)
105 (41)
15.0 (.95)
4.6 (13.8)
75 (24)
105 (41)
15.0 (.95)
4.6 (13.8)
85 (29)
110 (43)
15.0 (.95)
4.6 (13.8)
Values are based on 95°F (35°C) ambient, 77°F (25°C) discharge air, 10°F (5°C) temperature rise on the heat transfer media.
30
Drycooler and Piping Installation—Liebert XDFW
6.2.2
Expansion Tanks, Fluid Relief Valves and Other Devices
An expansion tank must be provided for expansion and contraction of the fluid due to temperature
change in this closed system. Vents are required at system high points to vent trapped air when filling the system. A relief valve is also necessary.
Depending on the complexity of the system, various other devices may be specified. Pressure gauges,
flow switches, automatic air separator, tempering valves, standby pumps, sensors for electrical controls and flow switches are just a few of these devices.
Manual shutoff valves should be installed on the supply and return lines. In addition, multiple pump
packages require a check valve at the discharge of each pump to prevent back-flow through the
standby pump(s). These check valves permit isolating units for routine maintenance or in an emergency.
Liebert also recommends installing these items in the system:
• cleanable, 60-mesh filters—These filters will trap the particles in the coolant supply line and
extend the service life of the water-cooled condenser.
• floor drains with wet traps or a leak-detection system, such as Liebert’s Liqui-tect™
• hose bibs at the lowest point of the system to facilitate filling
• relief valve—to protect against burst water pipes
6.2.3
Corrosion Protection
Read and follow individual unit installation instructions for precautions regarding fluid system
design, material selection and use of field-provided devices. Liebert systems contain iron and copper
alloys that require appropriate corrosion protection.
Contact a local water consultant regarding water quality, corrosion and freeze protection requirements. Water chemistry varies greatly by location, as do the required additives, called inhibitors that
reduce the corrosive effect of the fluids on the piping systems and components. The chemistry of the
water used must be considered because water may contain corrosive elements that reduce the effectiveness of the inhibited formulation.
Surface waters that are classified as soft and are low in chloride and sulfate ion content (less than 100
parts per million each) should be used. Proper inhibitor maintenance must be performed to prevent
corrosion of the system. Consult glycol manufacturer for testing and maintenance of inhibitors.
Commercial ethylene glycol, when pure, is generally less corrosive to the common metals of construction than water itself. It will, however, assume the corrosivity of the water from which it is prepared
and may become increasingly corrosive with use if not properly mixed with corrosion inhibitors. For
further details on corrosion prevention, see 6.3.1 - Glycol Solutions.
Idle fluid allows the collection of sediment and that prevents the formation of a protective oxide layer
on the inside of tubes. Keep the unit switched On and the system pump operating.
6.2.4
Freeze Protection—Coolant Type and Insulation
Glycol solutions should be considered for use as a coolant to protect the coil against freezing and corrosion from water.
! CAUTION
Risk of frozen fluid. Can cause piping rupture and equipment damage.
When the field piping or unit can be exposed to freezing temperatures, charge the system with
the proper percentage of glycol and water for the coldest design ambient to prevent freezing.
! CAUTION
Risk of frozen fluid. Can cause piping rupture and equipment damage.
Immediately after using water for leak testing or system cleaning, charge the tested
system with the proper percentage of glycol and water for your coldest design ambient.
Complete system drain-down cannot be ensured and damage to the system could result
from freezing of residual water.
The minimum coolant temperature to be supplied to the Liebert XDF will determine whether the supply and return lines require insulation to prevent condensation.
31
Drycooler and Piping Installation—Liebert XDFW
6.3
Drycooler Loop System
6.3.1
Glycol Solutions
The percentage of glycol to water must be determined by using the lowest design outdoor temperature
in which the system is operating. Table 3 indicates the solution freeze point at several concentration
levels of ethylene glycol. Propylene glycol concentrations should be 1% higher than the ethylene glycol
table values to find the freeze point. For example, 41% propylene glycol freezes at -10°F (-12°C).
Table 3
Ethylene glycol concentrations
% Glycol by Volume
Freezing Point °F (°C)
Apparent Specific Gravity
@ 50°F (10°C)
0*
32 (0)
10
25 (-3.9)
20
16 (-8.9)
30
5 (-15.0)
40
-10 (-23.3)
50
-32 (-35.5)
1
1.014
1.028
1.042
1.057
1.071
* A minimal amount of glycol should be considered for inhibitive coil protection.
The user must determine whether the planned use of glycol complies with national, state and local
regulations.
! CAUTION
Risk of material reaction. Can cause piping damage.
Galvanized pipe must not be used in or with systems or units that contain glycol.
Phosphates in the inhibitor can react with zinc in the galvanized pipe, precipitating an
insoluble material that can foul the system.
NOTE
When mishandled, glycol products pose a threat to the environment. Before using any glycol
products, review the latest Material Safety Data Sheets and ensure that you can use the
product safely. For Material Safety Data Sheets and other product safety information, contact
the nearest supplier.
Glycol manufacturers request that the customer read, understand and comply with the
information on the product packaging and in the current Material Safety Data Sheets. Make
this information available to anyone responsible for operation, maintenance and repair of the
drycooler and related equipment.
Typical inhibited formula ethylene glycol and propylene glycol manufacturers and suppliers are
Union Carbide (Ucartherm) or Dow Chemical (Dowtherm SR-1, Dowfrost). These glycols are supplied
with corrosion inhibitors and do not contain a silicone anti-leak formula. Do not use glycols with silicone anti-leak additives because they reduce cooling performance. Commercial ethylene glycol, when
pure, is generally less corrosive to the common metals of construction than water itself. Aqueous solutions of these glycols, however, assume the corrosivity of the water from which they are prepared and
may become increasingly corrosive with use if not mixed with corrosion inhibitors.
NOTE
Automotive antifreeze is unacceptable and must NOT be used.
Table 4
Glycol supply flow rates
Glycol
Type
Entering Coolant
Temperature, (ECT) °F (°C)
Saturated Cond.
Temperature (SCT),°F (°C)
Flow Rate
GPM (l/s)
Pressure
Drop, ft (kPa)
Ethylene (40%)
115 (46)
135°F (57°C)
15.0 (.95)
11.6 (34.6)
Propylene (40%)
115 (46)
135°F (57°C)
15.0 (.95)
18.5 (55.4)
Table assumes 95°F ambient, 77°F discharge air, 10°F temperature rise on the heat transfer media.
Table 5
Drycooler selection
Ambient
Temperature, °F (°C)
Drycooler
Model
Glycol Pump
hp
Standard Pump Model
1-Phase (57 ft @ 15GPM)
High Head Pump Model
3-Phase (70 ft @ 15GPM)
95 (35.0)
D** 092A
3/4
P13-0030
P02-0340
105 (40.6)
D** 174A
3/4
P13-0030
P02-0340
110 (43.3)
D** 225A 16
3/4
P13-0030
P02-0340
32
Drycooler and Piping Installation—Liebert XDFW
6.4
Filling the Liebert XDFW with Coolant
6.4.1
Preparing the System for Filling
It is important to remove any dirt, oil or metal filings that may contaminate the cooling system piping
in order to prevent contamination of the coolant and fouling of the drycooler piping (IF USED). The
system should be flushed thoroughly using a mild cleaning solution or high-quality water and then
completely drained before charging with coolant.
Cleaning new systems is just as important as cleaning old ones. New systems might be coated with oil
or a protective film; dirt and scale are also common. Any residual contaminants could adversely affect
the heat transfer stability and performance of your system. In many cases, in both old and new systems, special cleaners are needed to remove scale, rust and hydrocarbon foulants from pipes, manifolds and passages. Clean heat transfer surfaces are important in maintaining the integrity of the
cooling system. For more information on cleaners and degreasers, contact your sales representative.
Calculate the internal volume of the system as closely as possible. See Table 6 and Table 3 for unit
volumes.
6.4.2
Liebert XDFW Coolant Capacity
The water/glycol-cooled Liebert XDF’s coolant capacity is 0.56 of a gallon (2.1 liters). In closed systems, additional coolant will be required for the piping. Refer to Table 6 for required amounts for various piping sizes.
Table 6
Volume in standard Type “L” copper piping
Diameter (in.)
6.4.3
Volume
Outside
Inside
Gal/Ft
L/M
1/2
0.123
0.008
0.01
5/8
0.555
0.012
0.15
3/4
0.666
0.018
0.22
7/8
0.785
0.025
0.31
1-1/8
1.025
0.043
0.53
Filling the Liebert XDFW with Water or Glycol
When filling the Liebert XDF with either water or glycol, keep air to a minimum. Air in glycol turns to
foam and is difficult and time-consuming to remove. (Anti-foam additives are available and may be
considered.)
1. Open all operating systems to the loop.
2. With the top vent(s) open, fill the system from the bottom of the loop. This will allow the coolant to
push the air out of the top of the system, minimizing trapped air.
3. Fill to approximately 80% of calculated capacity.
Fill slowly from this point, checking fluid levels until the system is full.
NOTE
For glycol solution preparation and periodic testing, follow manufacturer's recommendations.
Do not mix products of different manufacturers.
33
Condenser Installation for Air-Cooled Units with Remote Condenser
7.0
CONDENSER INSTALLATION FOR AIR-COOLED UNITS WITH REMOTE CONDENSER
7.1
Remote Condenser Installation—XDFR
For details on installing the condenser, refer to the condenser’s installation manual or contact your
local Emerson Network Power representative. The manual was shipped with the unit and is available
at the Liebert Web site: www.liebert.com
7.2
Condenser Location
The air-cooled condenser should be located for maximum security and maintenance accessibility.
Avoid ground level sites with public access or areas that contribute to heavy snow or ice accumulations. Utilize centrifugal condensers whenever interior building locations must by used. To assure
adequate air supply, it is recommended that condensers be located in a clean air area, away from
loose dirt and foreign matter that may clog the coil. In addition, condensers should not be located in
the vicinity of steam, hot air or fume exhausts. Also, condensers should be located no closer than
3 feet (1 meter) from a wall, obstruction or adjacent unit.
Install condensers in a level position to assure proper coolant flow and oil return. For roof installation, mount condensers on steel supports in accordance with local codes. To minimize sound and
vibration transmission, mount steel supports across load bearing walls. For ground installation, a
concrete pad will provide adequate support. Condenser legs have mounting holes for securing the condenser to the steel supports or concrete pad.
Figure 26 Condenser planning dimensional data—One-fan units
Overall height to the top
of the fan guard is 43-1/8" (1095mm)
51-1/2"
(1308mm)
43-9/16"
(1106mm)
42"
(1067 mm)
37-7/8"
(962mm)
One -Fan
Condenser
41-3/16"
(1046 mm)
18"
(457mm)
43-3/16"
(1097mm)
44"
(1118mm)
ANCHOR PLAN
See Figure 27 for typical condenser
footprint dimensions.
34
Condenser Installation for Air-Cooled Units with Remote Condenser
Figure 27 Typical condenser footprint—dimensions
1" (25.4mm)
1-3/4"
(44.5mm)
4-1/4"
(108 mm)
2"
(50.8mm)
1-3/4"
(44.5mm)
9/16" (14mm)
Typical Diameter
4-1/4"
(108mm)
2"
(50.8mm)
Figure 28 Piping connection locations for 1-fan VFD control condensers
Traps to extend above
coil base by a minimum
of 7-1/2" (190mm)
Entering
Hot Gas Line
Leaving
Liquid Line
Inverted Traps
(field-supplied)
Metal
clamp
Fasten liquid and hot gas lines
to leg using flat surface clamps
with isolators (field-supplied).
Support field piping separately
to avoid coil damage and loss
of charge.
See
Detail
A-A
Isolator
Detail A-A
DPN000665
Rev. 02
35
Condenser Installation for Air-Cooled Units with Remote Condenser
Figure 29 Piping connections for 1-fan Liebert Lee-Temp condensers
Inverted Traps (field-supplied)
to extend 8" (203mm) above
coil base
Entering
Hot Gas Line
Hot Gas
Line
Liquid
Line
Fasten liquid and hot gas lines
to leg using flat surface clamps
with isolators (field-provided).
Support field piping separately
to avoid coil damage and loss
of charge.
See Detail A-A
Leaving
Liquid
Line
Position elbow
to direct relief
valve downward
Metal clamp
Isolator
DPN001067
Rev. 0
Detail A-A
7.3
Electrical Connections
Refer to equipment nameplate regarding wire size and circuit protection requirements. Refer to electrical schematic when making connections. Make all wiring and electrical connection in accordance
with local and national codes.
! WARNING
Risk of electric shock. Can cause injury or death.
Disconnect all local and remote electric power before working within the unit. Use a voltmeter
to make sure power is turned Off before making any electrical connections.
7.3.1
Line Voltage
Line voltage electrical service is required for all air-cooled condensers at the location of the condenser.
This power supply does not have to be the same voltage as the indoor unit. This separate power source
may be 208, 230, 460, or 575 V, 60 Hz; or 200, 230, or 380/415 V, 50 Hz. The disconnect switch may be
factory-supplied and mounted in the electrical panel or field-supplied and mounted per local and
national codes.
7.3.2
Low Voltage
A control interlock between the condenser and the indoor unit is required and is connected between
70 and 71 in the handy box of the indoor unit and the electric panel of the air-cooled condenser. NEC
Class 1 wiring is required. The recommended wire sizing for control wiring runs up to 150 ft (45m) is
16AWG for 60Hz.
7.3.3
Liebert Lee-Temp/Flood Back Head Pressure Control Condensers
Liebert Lee-Temp condensers require a separate power supply for the heated receivers. This power
supply is connected to the electrical connection box on the end of the receiver.
36
Condenser Installation for Air-Cooled Units with Remote Condenser
7.4
Coolant Piping
All refrigeration piping should be installed with high temperature brazed joints. Prevailing good
refrigeration practices should be employed for piping supports, leak testing, dehydration and charging of the refrigeration circuits. For the Liebert XDFR, the coolant piping should be installed to minimize the amount of line set outdoors to limit the coolant’s exposure to cooler outdoor conditions that
might inhibit the suction pressure.
Unit refrigeration components and piping are shipped from the factory with a nitrogen holding
charge.
NOTE
The refrigeration piping should be isolated from the building by the use of vibration isolating
supports.
NOTE
Piping, including inverted trap(s), must be routed to allow unobstructed access to the panel
per the NEC.
NOTE
When installing field piping, care must be taken to protect all coolant lines from the
atmosphere, especially when using coolants with POE oils. Do not allow the piping to stand
open to air for more than 15 minutes. Units designed for R407C have a compressor that
contains POE oil that is very hygroscopic; that is, it quickly absorbs water from the air. The
longer the compressor piping is left open to air, the harder it will be to fully evacuate. If left
open too long, the POE oil may need to be replaced before achieving the required vacuum level.
NOTE
Keep the evaporator unit and condenser closed with their factory charge of dry nitrogen while
all field piping is installed. Keep the field piping clean and dry during installation, and do not
allow it to stand open to the atmosphere. When all the field interconnecting piping is in place,
vent the condenser dry nitrogen charge and connect to the field piping. Finally, vent the
evaporator unit dry nitrogen charge and make its piping connections last.
Follow all proper brazing practices including a dry nitrogen purge to maintain system
cleanliness.
Traps should be installed in the hot gas line on vertical risers at the base and every 25 feet (7.6
meters) in elevation. These traps will collect condensed coolant and coolant oil during the Off cycle of
the unit and ensure flow of coolant oil during operation.
NOTICE
Risk of inadequate compressor oil. Can cause equipment damage.
Compressor oil must be added when the coolant lengths exceed 150ft (45m) for a Liebert
XDFR with a VFD condenser and 50ft (15m) for a XDFR for a Liebert Lee-temp condenser.
Failure to do so will result in damage to the compressor. Two ounces (59ml) of oil must be
added for every 10lb (4.5kg) over 40lb (18kg) of coolant charge.
Factory approval is required whenever:
• an R407C system condenser must be installed below the level of the cooling coil
• the total rise of the coolant piping exceeds 40 ft.
Total discharge line pressure drop must not exceed 10 PSIG (69 kPa).
Consult your local Liebert representative when considering installations outside these guidelines.
37
Condenser Installation for Air-Cooled Units with Remote Condenser
Table 7
Equivalent lengths (feet) for various pipe fittings
Copper Pipe
O.D. in.
90 Degree
Elbow Copper
90 Degree
Elbow Cast
45 Degree
Elbow
Tee
Gate
Valve
Globe
Valve
Angle
Valve
1/2
0.8
1.3
0.4
2.5
0.26
7.0
4.0
5/8
0.9
1.4
0.5
2.5
0.28
9.5
5.0
3/4
1.0
1.5
0.6
2.5
0.3
12.0
6.5
7/8
1.45
1.8
0.8
3.6
0.36
17.2
9.5
1-1/8
1.85
2.2
1.0
4.6
0.48
22.5
12.0
1-3/8
2.4
2.9
1.3
6.4
0.65
32.0
16.0
1-5/8
2.9
3.5
1.6
7.2
0.72
36.0
19.5
Coolant trap = 4 times equivalent length of pipe per this table.
Table 8
Indoor unit R407C charge, approximate
R407C Charge,
lb (kg)
Model
XDFR141
2 (0.9)
Table 9
Line charges - R407C per 100 ft (30 m) of Type “L” copper tube
R407C
O.D.
Liquid Line
lb (kg)
Hot Gas Line
lb (kg)
5/8"
11.0 (4.6)
2.2 (0.9)
7/8"
23.0 (9.6)
4.5 (1.9)
Table 10
Condenser R407C
R407C
Approximate Charge, lb (kg)
Model
VFD
Lee-Temp*
083
5 (2.27)
26 (11.8)
* Charge includes the receiver charge.
Table 11
Condenser
Model
Condenser connection sizes
Number
of Fans
Number
of Circuits
1
1
TCSV083
CSL083
7.5
Connection Size, OD, In.
Hot Gas
Liquid
Net Weight
lb (kg)
7/8
7/8
295 (134)
VFD Systems
The VFD condenser utilizes a variable frequency drive, inverter duty fan motor operating from 0% to
100% motor RPM based on head pressure, sensed by coolant pressure transducers. VFD, ambienttemperature thermostat(s), motor overload protection and electrical control circuit are factory-wired
in the integral control panel. VFD controls the fan adjacent to the connection end of the condenser
and remains energized with active compressor operation. The balance of fans on multi-fan units cycle
on ambient thermostats. This system provides coolant head pressure control for outdoor ambients as
low as 0°F (-18°C). The Liebert Lee-Temp condenser must be used for temperatures lower than
0°F (-18°C).
38
Condenser Installation for Air-Cooled Units with Remote Condenser
7.5.1
Materials Supplied with Condenser
•
•
•
•
•
•
7.5.2
Built-in, wired condenser control box
Air-cooled condenser
Piping access cover to be reinstalled when piping is complete
Bolts (four per leg) 3/8" x 5/8"
Terminal block for two-wire, 24-volt interlock connection between unit and condenser
Condenser legs, four on one-fan models
Dehydration/Leak Test and Charging Procedures for VFD Condenser
NOTICE
Risk of improper handling of coolant. Can result in enviornmental degradation and violation
of regulations.
All local codes for handling coolant must be followed.
NOTE
R407C uses a POE (polyol ester) lubricant. The R407C coolant must be introduced and
charged from the cylinder only as a liquid.
NOTE
When installing field piping, care must be taken to protect all coolant lines from the
atmosphere, especially when using coolants with POE oils. Do not allow the piping to stand
open to air for more than 15 minutes. Units designed for R407C have a compressor which
contains POE oil that is very hygroscopic; that is, it quickly absorbs water from the air. The
longer the compressor piping is left open to air, the harder it will be to fully evacuate. If left
open too long, the POE oil may need to be replaced before achieving the required vacuum level.
Dehydration/Leak Test
1. Disconnect all power to the Liebert XDFR. Lock out and tag out all input power connections.
NOTE
The Liebert XDFR uses a 208VAC liquid line solenoid valve. These instructions allow the
system to be evacuated, pressure-checked and charged without having to power the solenoid. To
do this, a jumper hose (see Step 2) is to be used to access the piping between the discharge line
check valve and liquid line solenoid valve.
2. Connect a jumper hose from the Schrader port on the suction line to the Schrader port on the
compressor discharge rotalock.
3. Connect the low-side coolant gauge to the compressor suction rotalock.
4. Connect the high side coolant gauge to the liquid line coupling located just outside of the Liebert
XDFR’s rear panel.
5. Pressurize the system circuits to 150 PSIG (1034 kPa) with dry nitrogen and a trace of coolant.
6. Check the system for leaks with leak finder.
7. After completing the leak tests, release the test pressure (per local code) and pull a deep vacuum
on the system.
8. Wait four hours, then check the pressure readings.
a. If the pressure readings have not changed, break the vacuum with dry nitrogen.
b. Pull another vacuum to 250 microns or less.
c. Wait two hours, then recheck the pressure.
d. If the pressure is unchanged, the system is ready for charging as detailed in 7.5.3 Charging.
39
Condenser Installation for Air-Cooled Units with Remote Condenser
Figure 30 Air-cooled VFD control, general arrangement
Condenser
Coil
Schrader
Valve
Fusible
Plug
Inverted Traps on Discharge
and Return Lines Outside
of Condenser to Extend Above
Base of Coil by a Minimum
of 7-1/2" (190mm)
Evaporator
Coil
Traps* Every
25 ft. (7.6m)
of Rise
Liquid Return
Solenoid
Valve
Expansion
Valve
Shutoff
Valve *
Sensing
Bulb
External
Equalizer
Filter Dryer
Service
Valves
Maximum Total
Piping Rise:
40 ft. (12.2m)
Digital Scroll
Compressor
Check Valve
SINGLE CIRCUIT SHOWN
Hot Gas
Discharge
FACTORY PIPING
FIELD PIPING
* Components are not supplied by Emerson
but are recommended for proper circuit
operation and maintenance.
40
SL-11897
Page 5
Condenser Installation for Air-Cooled Units with Remote Condenser
7.5.3
Charging
1. Disconnect all power to the Liebert XDFR. Lock out and tag out all input power connections.
2. Ensure that all operational components are clear of debris.
3. Remove the jumper hose installed in 7.5.2 - Dehydration/Leak Test and Charging
Procedures for VFD Condenser.
4. Remove the high-side hose and place it on the Schrader port of the compressor discharge rotalock.
5. Remove the low-side coolant hose and place it on the liquid line coolant coupling.
6. Connect the coolant gauge charging hose to the drum of coolant.
7. Calculate the amount of charge for the system. Refer to the unit, condenser and coolant line
charge (see Tables 8, 9 and 10).
8. Place a heater blanket on the R407C cylinder and weigh in the calculated amount of charge.
7.6
Liebert Lee-Temp/Flood Back Head Pressure Control Systems
The Liebert Lee-Temp system consists of a modulating type head pressure control valve and insulated
receiver with heater pad are required if the system will operate in temperatures as cold as -20°F
(-29°C).
7.6.1
Piping
NOTICE
Improper protection of the check valve during soldering or brazing may damage the
component, necessitating replacement by the user.
A factory-supplied Liebert Lee-Temp Piping assembly must be field-installed on the
condenser. During soldering or brazing near the check valve on the Liebert Lee-Temp Piping
Assembly, the internal parts must be protected by wrapping the valve with a damp cloth to
keep the valve temperature below 250°F (121°C).
7.6.2
Materials Supplied with Condenser
•
•
•
•
•
•
•
Built-in pre-wired condenser control box
Air-cooled condenser
Piping access cover to be reinstalled when piping is complete
Bolts (four per leg) 3/8" x 5/8"
Terminal block for two-wire 24V interlock connection between the unit and the condenser
Condenser legs: four on one-fan models
Lee-Temp system:
• Insulated storage receiver
• Head pressure control valve with integral check valve
• Adapter assembly
• Rotalock valve
• Pressure relief valve
• Liquid level sight glass
• Check valve
• Bolts - six per receiver, 3/8" x 1"
NOTE
Liebert Lee-Temp heater pad requires a separate, continuous electrical source of either
115 VAC or 200/208/230 VAC.
41
Condenser Installation for Air-Cooled Units with Remote Condenser
7.6.3
Dehydration/Leak Test and Charging Procedures for Liebert Lee-Temp Control Type
Condenser
NOTICE
Risk of improper handling of coolant. Can result in enviornmental degradation and violation
of regulations.
All local codes for handling coolant must be followed.
NOTE
R407C uses a POE (polyol ester) lubricant. The R407C coolant must be introduced and
charged from the cylinder only as a liquid.
NOTE
When installing field piping, care must be taken to protect all coolant lines from the
atmosphere, especially when using coolants with POE oils. Do not allow the piping to stand
open to air for more than 15 minutes. Units designed for R407C have a compressor which
contains POE oil that is very hygroscopic; that is, it quickly absorbs water from the air. The
longer the compressor piping is left open to air, the harder it will be to fully evacuate. If left
open too long, the POE oil may need to be replaced before achieving the required vacuum level.
Dehydration/Leak Test
1. Disconnect all power to the Liebert XDFR. Lock out and tag out all input power connections.
NOTE
The Liebert XDFR uses a 208VAC liquid line solenoid valve. These instructions allow the
system to be evacuated, pressure-checked and charged without having to power the solenoid. To
do this, a jumper hose (see Step 2) is to be used to access the piping between the discharge line
check valve and the liquid line solenoid valve.
2. Connect a jumper hose from the Schrader port on the suction line to the Schrader port on the
compressor discharge rotalock.
3. Connect the low-side coolant gauge to the compressor suction rotalock.
4. Connect the high-side coolant gauge to the liquid line coolant coupling located just outside of the
Liebert XDFR’s rear panel.
5. At the condenser, attach a jumper hose from the rotalock valve on the outlet of the receiver to the
Schrader port on the liquid header of the condenser.
6. Front-seat the receiver rotalock valve approximately two turns.
7. Pressurize the system circuit to 150 PSIG (1034 kPa) by using dry nitrogen with a trace of
coolant.
8. Check the system for leaks with leak finder.
9. After completing the leak tests, release the test pressure (per local code) and pull a deep vacuum
on the system.
10. Wait four hours and check the pressure readings.
a. If the pressure readings have not changed, break the vacuum with dry nitrogen.
b. Pull another vacuum to 250 microns or less.
c. Wait two hours and recheck the pressure.
d. If the pressure is unchanged, the system is ready for charging as detailed in 7.6.4 Charging.
42
Condenser Installation for Air-Cooled Units with Remote Condenser
7.6.4
Charging
1. Disconnect all power to the Liebert XDFR. Lock out and tag out all input power connections.
2. Ensure that all operational components are clear of debris.
3. Remove the jumper hose installed in 7.6.3 - Dehydration/Leak Test and Charging
Procedures for Liebert Lee-Temp Control Type Condenser.
4. Remove the high-side hose and place it on the Schrader port of the compressor discharge rotalock.
5. Remove the low-side coolant hose and place it on the liquid line coolant coupling.
6. At the condenser, remove the jumper hose between the receiver rotalock valve and the liquid line
Schrader port.
7. Connect the coolant gauge charging hose to the drum of coolant.
8. Calculate the amount of charge for the system. Refer to the unit, condenser and coolant line
charge (see Tables 8, 9 and 10).
9. Place a heater blanket on the R407C cylinder and weigh in the calculated amount of charge.
Liebert Lee-Temp Receiver Coolant Level
On the receiver at the condenser are two coolant-level sight glasses. Coolant level will vary with outside temperature. Check coolant level after the unit has been on for at least 15 minutes.
Sight Glass Levels
40°F (4.5°C) and lower—bottom sight glass is 3/4 full
40 to 60°F (4.5 to 15.5°C)—bottom sight glass is full
60°F (15.5°C) and higher—top sight glass is 3/4 full.
43
Condenser Installation for Air-Cooled Units with Remote Condenser
Figure 31 Air-cooled, Liebert Lee-Temp general arrangement
Condenser Coil
Inverted Trap on Discharge
Line Outside of Condenser
to Extend Above Base
of Coil by a Minimum
of 7-1/2" (190mm)
Piping Assembly **
Head Pressure
Control with
Integral Check
Valve
Traps* Every
25 ft. (7.6m)
of Rise on
Hot Gas Line
Only
Rotalock Valve **
Check Valve
Liebert
Lee-Temp
Receiver
1/4" (6.4mm)
Pressure Relief
Valve **
Sight Glass
Evaporator
Coil
Liquid Return
from Condenser
Expansion
Valve
Solenoid
Valve
Shutoff
Valve *
Sensing
Bulb
External
Equalizer
Filter Dryer
Liquid Return
Service
Valves
Digital Scroll
Compressor
Maximum Total
Piping Rise:
40 ft. (12.2m)
Check
Valve
Hot Gas Discharge
SINGLE CIRCUIT SHOWN
FACTORY PIPING
OPTIONAL PIPING
FIELD PIPING
* Components are not supplied by Emerson ** Components supplied
but are recommended for proper circuit
by Emerson; must be
operation and maintenance.
field-installed.
44
SL-10061 PG. 4
SL-10071 PG. 4
Electrical Connections
8.0
ELECTRICAL CONNECTIONS
Power is supplied to the Liebert XDF through two factory-connected power cords (120V and 208V).
For more information, refer to 5.2.1 - Voltage Input Requirements
Additional electrical connections required for operation depend on the equipment installed in the Liebert XDF and remote communications desired.
The Liebert XDF has slots for two communication cards, such as Liebert’s Intellislot card, and two
alarm/warning hardwire connections. These connections are at the top left corner of the self-contained, air-cooled Liebert XDF, inside the area housing the condenser coil (see Figure 32). For
details, see 11.1 - Environmental Control. Water-cooled Liebert XDF units have the connections on
the top of the unit, near the middle of the compartment (see Figure 33).
Alarm and warning contacts may be connected to monitoring equipment, such as Liebert’s Universal
Monitor and SiteLink equipment, as well as to building management systems. Consult the monitoring equipment’s user manual for details.
Figure 32 Customer electrical connections and cable entry points—self-contained, air-cooled units
Ambient
Temperature/Humidity
Sensor
Customer Connections:
75 & 76 Customer Alarm Contacts
94 & 95 Customer Warning Contacts
37 & 38 Remote Shutdown Contacts
(all contacts rated 1A, 24VAC maximum)
Communication
Card Slots (cards
provided when
option is selected)
Customer
Cable Entry
Points
Dashed line delineates
equipment compartment
45
Electrical Connections
Figure 33 Customer electrical connections and cable entry points—water/glycol-cooled units and remote,
air-cooled units
Ambient
Temperature/Humidity
Sensor
Customer Connections:
37 & 38 Remote Shutdown Contacts
75 & 76 Customer Alarm Contacts
94 & 95 Customer Warning Contacts
(Contacts listed from top to bottom;
All contacts rated 1A, 24VAC maximum)
70 & 71 Heat Rejection Device Connection
(Remote air condenser and water-cooled
models only)
Communication
Card Slots (cards
provided when
option is selected)
WATER-COOLED UNIT SHOWN;
The location of the remote connections
are the same for both the water-cooled
and the remote air condenser models.
RETURN
(OUT)
Customer
Cable Entry
Points
SUPPL Y
(IN)
Dashed line
delineates
equipment
compartment
TOP VIEW
Rear
Power connection locations
(refer to Figure 32 for details)
46
Electrical Connections
8.1
Utility Power Supply
The Liebert XDF’s 120V and 208V input power cords are stored for shipment in a compartment at the
bottom left of the rear of the Liebert XDF. The 10 feet (3m) cords may be routed to power outlets on
the floor or wall.
If the power connections are overhead, the cables may be routed inside the unit and out the top. Liebert recommends pulling the cables across the floor of the rack-mounted equipment compartment and
up the right rear side. This permits securing cables to the cable management cutouts along the inside
of the Liebert XDF.
! WARNING
Before beginning any work inside the Liebert XDF, disconnect all power inputs to the Liebert
XDF and installed equipment.
8.1.1
Route Input Power Cables Through the Liebert XDF’s Top
To route the factory-supplied input power cables inside the unit and out the top:
1. Open the rear door, revealing the back of the rack-mount equipment compartment.
2. Remove the six Phillips screws securing the small metal plate at the bottom left (inside the rackmount equipment compartment; see Figures 32 and 34).
3. Remove the cable entry snap bushing at the top right side of the rack-mount equipment
compartment to access the condenser coil compartment.
4. Remove the cable entry snap bushing from the top of the Liebert XDF.
5. Attach an optional cable bundle to the top of the panel that separates the rack-mount equipment
compartment from the condenser compartment.
6. Feed the input power cords through the opening at the bottom of the Liebert XDF and route them
through the optional cable bundle and out the top (see Figure 34).
7. Secure the cable bundle seal around the input power cords.
8. Secure the input power cables to the side of the Liebert XDF with optional Velcro ties or cable
rings.
9. Install the small plate removed in Step 2 on the back of the Liebert XDF just above the
condensate drain (see Figure 34).
10. Connect the input power cables to appropriate utility supplies.
Figure 34 Route input power cords through Liebert XDF top
Attach optional
cable bundle to
upper side of
cable entry cutout
Secure input
power cables
to side panel
Plate moved from inside
rack-mount equipment area
Route input power cables across
bottom of XDF to right rear side
47
Cable Management Options
9.0
CABLE MANAGEMENT OPTIONS
The Liebert XDF is able to host many of the components of the Foundation cable management products. These optional items deliver a flexible solution to rack-enclosure cable problems by utilizing a
patent pending platform to provide adaptive equipment and cabling support. Cable and equipment
mounting options are available to meet changing requirements.
9.1
Cable Management Considerations
When designing the equipment layout in the Liebert XDF, consider how cables must be run for each
configuration and how cable runs affect cooling, access and operational factors. Separate power and
communication cables to reduce electromagnetic interference.
Good cable management contributes to:
• Effective airflow for cooling
• Easier cable identification
• Improved access
• Reduced electromagnetic interference
• Proper bend radii, particularly for fiber optic cables
• Adequate support for large cables and heavy cable bundles
Several Foundation options are designed to facilitate structured cable management. These are
described in 9.4 - Optional Cable Management Channel.
NOTE
When installing cables, leave enough slack for the unit to be rolled forward or sideways.
Do not block or restrict cooling system discharge or return airflow.
Do not defeat the ground/earth connections between the utility/mains outlet and the Liebert
XDF.
9.2
Cable Management
Once your equipment has been installed, you are ready to connect cables for power and communication. Before making any connections, check the equipment to ensure that all power switches are in
the Off position.
Numerous cable entrances and management provisions are built into the Liebert XDF to ease cable
installation.
Optional cable rings and Velcro straps, along with some components for routing cables, can be used
with the Liebert XDF. These help not only to keep your cables organized but also separate power and
communications cables, reducing electromagnetic interference. A wide area is provided on the left
rear side of the frame to mount cable rings, Velcro straps and cable trays. This location contributes to
cooling efficiency by keeping equipment cables out of the cooling air pattern (see Figure 37).
Figure 35 Cable rings, Velcro straps on Liebert XDF rails
Cable Rings
Mounted
on Rail
Front
Strap
Optional Velcro Strap
Positioning on Rails Front or
Rear
48
Rear
Strap
Cable Management Options
9.3
Cable Access
9.3.1
Top Cover and Back
Optional sealed entrance cable bundles (cone-shaped seals and clamps)
permit use of the round openings on the top of the Liebert XDF for cable
entry.
To bring cable through these holes:
1. Replace the plug with a sealed entrance cable bundle.
2. Pull the cable through the bundle.
3. The cable bundle can be trimmed to accommodate various quantities
of cables.
4. Use the clamp to secure the bundle around the cables.
9.4
Sealed Entrance
Cable Bundle
Optional Cable Management Channel
The optional Foundation Cable Management Channel (CMC) combines with other optional items to
permit the user to route cables in an organized, efficient manner.
CMCs are available in 1U, 2U and 3U sizes and are adjustable for side-to-side or front-to-rear orientations.
Refer to Figures 37 and 38 for various cable management configurations and options.
Figure 36 Cable Management Channel lengths
17.44" (443mm)
20.75" (527mm)
30" (762mm) Front-to-Rear, Zero U
Cable Management Channel
bracket on back side of panel (both ends)
19" (483mm) Rack-Mount
23" (584mm)
CMC Panel Typical Flanges facing toward you
CMC Panel Typical Flanges facing toward you.
Long tabs of CMC brackets
fit inside flanges of
CMC panels.
19" (483) Cable Entrance and Exit
CMC Panel Typical Flanges facing toward you.
Typical 4 places
23.56" (598mm)
19" (483) Top Trough
25.44" (646mm)
38" (965mm)
Front-to-Rear, Zero-U, Closed-End Channel
CMC brackets can be inverted,
with the flanges facing away, for an open-end channel.
49
Cable Management Options
Figure 37 Cable management mounting locations and options: Velcro cable straps, cable spools
Customer
Cable
Entrance
Areas
Carriage Bolt
Cable Spool
3" Tall
Star Washer
Keps
Nut
Velcro
Cable
Strap
Carriage
Bolt
Star Washer
Cable
Spool
3" Tall
Cable Management
Option Mounting Areas
(inside rails and frame)
Keps
Nut
FRONT
Figure 38 Cable management accessories: Cable Tray
Flat Tab
Mounting Bracket
Cable
Tray
Flat-Head
Screw
Flat Tab
Mounting
Bracket
Small
Keps
Nut
Cable Tray
Cover
50
Startup
10.0 STARTUP
Before plugging in your electronic equipment, make sure that all power switches are in the Off position.
• Be certain there are no obstructions, wire bundles, manuals, trash, etc., in front of or on either
side of the Liebert XDF. Make sure all doors are shut and sealed properly.
• Plug the Liebert XDF’s 120V power cord into a dedicated utility circuit.
• Plug the Liebert XDF’s 208V power cord into a dedicated utility circuit.
10.1
Liebert XDF Startup Inspection Checklist
10.1.1 Site Conditions
___ 1. Confirm at least 36 in. (915mm) clearance in front of the Liebert XDF, on the right side and
behind the unit. No left-side clearance required.
___ 2. Confirm at least 36 in. (915mm) clearance above the unit (self-contained, air-cooled units
only; water/glycol units do not require clearance above).
___ 3. Confirm site ventilation provisions:
___ Sufficient ambient space to dissipate heat rejected by the Liebert XDF (self-contained,
air-cooled units).
___ Ambient temperature range is 35°F to 104°F (1.6 to 40°C).
___ 4. Ensure that the Liebert XDF is level.
___ 5. Confirm condensate drain tube is connected to a drain and will drain properly.
___ 6. Secure all electrical connections inside the Liebert XDF.
___ 7. Confirm that the dedicated circuits for the Liebert XDF’s compressor and fans are separate
from the circuit for the UPS (not same duplex).
___ Liebert XDF requires a 120V/60Hz/15A, single-phase, 2-wire plus ground circuit.
___ Record the fan working input voltage 120VAC (±10%): ____________________
___ Liebert XDF requires a 208V/60Hz/30A, three-phase, 4-wire plus ground circuit.
___ Record the compressor working input voltage 208VAC (±10%): ____________________
___ Check UPS (if provided) nameplate for input electrical requirements.
___ 8. Examine the positioning of equipment inside the cabinet.
___ Prevent short cycling of airflow - no spaces larger than 1U between electronic devices.
___ Spaces larger than 5U at top of rack are covered with blanking panels.
___ Heaviest equipment installed near the bottom of the cabinet.
___ 9. Check cabinet seals—No gaps, loose cables, air leaks:
___ Door gaskets intact / free of damage. Close front and rear doors and confirm no visible
seal violations.
___ Side panels and the frame have uniform sealing.
___ Cable entrance points are sealed.
___ 10. Determine whether the UPS, if one is installed in the Liebert XDF, has fully charged
batteries.
NOTE
The UPS’s batteries may require recharging before it can fully supply your equipment’s power
needs for the rated time if utility power fails.
To charge the UPS batteries before using the unit, you can apply power to the UPS module
while installing equipment or making adjustments.
Refer to the UPS manual for preparation for startup, details of UPS operation and the
meaning of LED indicators.
51
Startup
10.2
Starting the Liebert XDF
The Liebert XDF is started, stopped and controlled with Liebert’s iCOM controller. Figure 39 shows
the Liebert iCOM keypad.
Figure 39 Liebert iCOM controller keys
Alarm Key
Up Arrow Key
?
On/Off Key
Help Key
Left Arrow Key
Enter Key
Right Arrow Key
ESC
Escape Key
Down Arrow Key
To start the Liebert XDF:
1.
2.
3.
4.
5.
Press the On/Off key on the Liebert iCOM controller.
Confirm internal airflow: Inside enclosure, (evaporator fan discharge).
Confirm cooling air begins circulating.
Power up the UPS (if provided).
Close the Liebert XDF’s doors, if open.
NOTE
Control requires 30-60 seconds to boot up after the 120V power is supplied.
10.2.1 Evaporator Fan Operation
The evaporator fans will turn On whenever the unit control is active (powered).
10.2.2 Condenser Fan Operation
Normal Operation—The condenser fan will turn On whenever the unit is running and the compressor is On.
Backup Ventilation—The condenser fan will be On or Off when the backup ventilation is open,
depending on the Condenser Fan Ventilation setpoint. See 11.8 - Backup Ventilation System for
additional information.
NOTE
Only an Emerson-authorized representative can change the Condenser Fan Ventilation
setpoint.
52
Operation
11.0 OPERATION
The Liebert XDF is intended for operation with its doors closed and latched. This increases efficiency
and keeps out dust and humidity.
With the doors closed, the Liebert XDF will achieve full capacity in ambient conditions up to 95°F
(35°C) and 40 percent relative humidity. The Liebert XDF’s cooling efficiency is reduced if it is operated in higher ambient temperatures and humidity. The reduction varies according to the heat load
from the installed equipment and the external temperature and humidity.
The Liebert XDF may be operated for short periods with its doors open. Refer to Figure 11.7 - Operation With the Door Open.
11.1
Environmental Control
The Liebert XDF’s cooling functions are controlled by Liebert’s iCOM control module. This section
describes the Liebert iCOM’s basic functions, such as start-up and navigation. For further details on
setting up and using your Liebert iCOM, refer to 11.2 - Liebert iCOM Components and Functions and 11.3 - Navigating Through the Liebert iCOM Display or call 800-543-2778.
NOTE
The Liebert iCOM installed on the Liebert XDF is programmed for single-unit control. It does
not have the capability of communicating with other Liebert iCOM units. Disregard portions
of the Liebert iCOM manual that refer to multiple unit operations.
The menu-driven Liebert iCOM display is used for programming each cooling function. The screen
shows the status of the conditioned space, setpoints, alarm status and settings, event histories and
the current time.
Remote Communications—Building Management Systems, Liebert SiteScan
The Liebert iCOM controller on the Liebert XDF may be remotely accessed with Liebert’s SiteScan®
systems, Modbus or with SNMP.
Each Liebert XDF is equipped with Intellislot bays for use with optional communication cards:
• Liebert IntelliSlot® 485—enables the Liebert XDF to communicate via Modbus or BACnet protocols to Liebert’s SiteScan or third-party building management systems
• Liebert IntelliSlot Web—enables the Liebert XDF to communicate via SNMP
11.2
Liebert iCOM Components and Functions
The Liebert iCOM controller layout is shown in Figure 40.
Figure 40 Liebert iCOM display components
Liquid Crystal
Display screen
LED Status Indicators
(top LED is red or
flashing red; bottom
LED is green or
amber)
Keypad
53
Operation
Table 12
Icon
?
ESC
Keyboard icons and functions
Key Name
Function
On/Off Key
Controls the operational state of the cooling unit.
Alarm Key
Silences an alarm.
Help Key
Accesses integrated help menus.
ESCape Key
Returns to the previous display view.
Enter Key
Confirms all selections and selects icons or text.
Increase Key
(Up Arrow)
Moves upward in a menu or increases the value of a selected parameter.
Decrease Key
(Down Arrow)
Moves downward in a menu or reduces the value of a selected parameter.
Left and Right
Arrow Keys
Navigates through text and sections of the display.
Blinking Red—Active, unacknowledged alarm exists
Upper LED
Solid Red—Active, acknowledged alarm exists
Amber—Power is available to the unit, unit is NOT operating
Lower LED
Green—Power is available to the unit, unit is operating
54
Operation
11.3
Navigating Through the Liebert iCOM Display
Liebert iCOM displays icons and text for monitoring and controlling your Liebert cooling unit. The
Liebert iCOM’s default screen may be either graphical or simple (no bar graphs).
Figure 41 Liebert iCOM graphical display default screen components
Actual Ambient
Temperature
Actual Ambient
Relative Humidity
UNIT 1
Internal
Cabinet
Setpoint
Actual Internal
Cabinet Temperature
T
ACT
Evaporator Fans
73°F
72°F
UNIT ON
%
T
95°F
100%
30%
11/07
Percent Cooling
Next Scheduled
Maintenance
50%
Backup
Ventilation
(shows only
when
operating)
VENT
kW
10
OK
NO
Optional Load Monitor Readout
(amount of energy consumption
by internal equipment)
Open Door Operation (indicates whether
it is safe to open the door - only one icon
shows at a time)
Figure 42 Liebert iCOM simple display default screen components
Actual Ambient
Temperature
Internal
Cabinet
Setpoint
Actual Internal
Cabinet Temperature
Evaporator Fans
Actual Ambient
Relative Humidity
UNIT 1
T
ACT
73°F
72°F
100% 30%
UNIT ON
%
T
95°F
OK
NO
VENT
Backup Ventilation
(shows only when
operating)
Percent
Cooling
kW
10
50%
1
Open Door Operation (indicates
whether it is safe to open the
door - only one icon shows at a
time)
Optional Load Monitor Readout
(energy consumption by internal
equipment)
55
11/07
Next Scheduled
Maintenance
Active Alarms
(not displayed
when there are no
active alarms)
Operation
11.3.1 Accessing Menus and Settings
Viewing Data
No password is required to view data or settings.
To view data:
1. From the default screen, press the Enter key to view the opening page of the six-page user menu
(see Figure 43).
2. Press Enter again to highlight the password line.
3. Use the Down arrow to scroll to the icon for the data you wish to view.
4. Once that icon is highlighted, press Enter again to display the data.
If there are lines above or below what is shown on the screen, small arrows in the top right corner
and bottom right corner will be displayed (see Figure 44).
5. Press Enter to select the first line of data.
6. Use the Up and Down arrow keys to scroll to the desired data point.
7. Press ESC to move back to higher level menus.
Figure 43 Liebert iCOM user menu, Page 1 of 6
USER MENUS 1/6
PASSWORD LEVEL0
C/F
% RH
SET
????
SETPOINTS
Up and Down Arrows show additional
pages are above and below the current
page.
Left and Right Arrows show additional
screens and menus are available.
Note: Although Service and Advanced
menus may be viewed, changes may be
made only by factory-authorized service
personnel.
Password command
line—highlight by
pressing Enter
Figure 44 Accessing additional menu lines
DISPLAY SETUP
U404 TEMP F / C
U405 CONTRAST
U406 BUZ FREQ
°F
50%
50%
Arrows show there
are additional
lines above and
below
11.3.2 Entering the Password
1. From the default screen, press the Enter key to access the opening page of the six-page user
menu (see Figure 43).
2. Press Enter to highlight the Password command line.
3. With the password line highlighted, press Enter to highlight the first digit in the password; enter
the password, 1490.
4. Use the Up and Down arrow keys to select a numeral for the first digit of the password.
5. Move to the next digit of the password with the Right arrow key.
6. Select the numerals for all four digits with the same process.
7. After all four digits of the password have been entered, press the Enter key.
NOTE
Do not press the ESC key or the Liebert iCOM will move to the previous screen and the
password must be re-entered before changes may be made.
56
Operation
11.4
Changing Operational Settings
Changes to the Liebert XDF’s operation settings in the Set Alarms and Setpoints menus require a
password.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
From the default screen, press the Enter key to view the opening page of the six-page user menu.
Press Enter again to highlight the password line.
Enter the password (for help, see 11.3.2 - Entering the Password)
After entering the password, use the Up and Down arrow keys to scroll to the icon containing the
operational setting to be changed.
Press Enter to display the data for that icon.
Press Enter to highlight the first line of commands.
Use the Up and Down arrow keys to scroll to the command line to be changed.
Press Enter to highlight the setting.
Change the setting by using the Up and Down arrow keys.
Press Enter to accept the change. (The setting will no longer be highlighted.)
Press ESC to deselect the command line. (The command line will no longer be highlighted.)
Press ESC again to move to previous screens.
57
Operation
Table 13
User menu icons
Icon
Name
Description
°C / °F
% RH
SET
Setpoints
View and change internal cabinet temperature setpoint
(humidity setpoint inactive on Liebert XDF)
EVENT
LOG
Event Log
Contains last 400 events
Graphic Data Record
Displays temperature and humidity graphs
Set Alarms
Allows enable, disable and settings for alarms
Sensor Data
Shows readings of sensors
Display Setup
Change settings for display: language, time, simple or
graphic display
Total Run Hours
Records the run time of all components and allows
setting of limits on run time
Sleep Mode
Allows setback settings for non-peak operation
Service Contacts
Contains key contact information for local service,
including names and phone numbers
SET
ALARMS
12
9
3
6
SET
1234h
12
9
3
6
58
Operation
11.5
Changing Liebert iCOM’s Display Settings
No password is required to change the way Liebert iCOM displays data. The Display Setup submenus
control how such data as temperature, date and time is shown.
To change the display settings:
1.
2.
3.
4.
5.
6.
7.
8.
9.
From the default screen, press the Enter key (see Figure 39) to access the user menu.
Press the Enter key again to highlight the password command line.
Use the Up and Down arrow keys to navigate to the Display Setup icon.
Press the Enter key again to access the Display Setup submenu (see Figure 45).
Press the Enter key to select the first command.
Either change that setting or navigate to another setting with the Up and Down arrow keys.
Once the desired command line is highlighted, press the Enter key to access that parameter’s
display setting options.
Use the Up and Down arrow keys to make changes.
Press the Enter key to accept the changes.
Press the ESC key twice to return to Liebert iCOM’s user menu.
Figure 45 Display setup screen
DISPLAY SETUP
Highlight the
setting to be
changed by
pressing Enter.
11.6
U404 TEMP F / C
U405 CONTRAST
U406 BUZ FREQ
°F
50%
50%
Changing the Liebert XDF’s Default Operating Temperature
The Liebert XDF’s internal temperature is set at the factory at 72°F (22°C). This setpoint is adjustable from 65°F to 80°F (18-27°C). To change this setpoint:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
From the default screen, press the Enter key (see Figure 39) to access the user menu.
Press Enter a second time to select and highlight the Password line.
Enter the password (see 11.3.2 - Entering the Password).
Use the Down arrow key highlight the Setpoints icon.
Press the Enter key to enter the setpoints submenu.
Press the Enter key to highlight TEMP SET command line.
Press Enter again to access the setpoint adjustment.
Use the Up and Down arrow keys to select the desired setpoint.
Press the Enter key to accept the selected setpoint.
Press the ESC key twice to return to the Liebert iCOM’s user menu.
For further details about the Liebert iCOM controller, see 11.2 - Liebert iCOM Components and
Functions and 11.3 - Navigating Through the Liebert iCOM Display. For more complete information about the Liebert iCOM controller, call 800-543-2778.
59
Operation
11.7
Operation With the Door Open
If the external ambient dew point exceeds the Liebert XDF’s internal
temperature, the Liebert iCOM control will flash a warning that condensation may form inside the enclosure if a door is opened. The warning is an icon of a door with an “X” on top of it. The word NO appears
beside the icon.
If a warning is flashing, the Liebert XDF’s doors may be opened safely
while the unit is operating by following these steps:
NO
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
From the default screen, press the Enter key (see Figure 39) to access the user menu.
Press Enter a second time to select and highlight the Password line.
Use the Down arrow to scroll to the Setpoints icon.
Press the Enter key again to access the Setpoints submenu.
Press Enter again to highlight the first command line.
Using the Down arrow key to highlight the DOOR OP command line.
Hit the Enter key to highlight the setting adjustment.
Use the Up and Down arrow keys to change the status to YES.
Press Enter to accept the change.
Hit the ESC key four times to return to the default screen.
The Liebert iCOM control will begin reducing cooling until the Liebert XDF’s internal
temperature is high enough that condensation will not occur if the door is opened.
12. Once the internal temperature reaches this point, the “Door Open Wait Timer” starts counting
down.
The Liebert XDF may be opened without internal condensation
when the default screen removes the “X” from the door icon and the
word OK appears beside the icon.
The Liebert XDF will keep the temperature at the level required for
opening the door for two minutes. If a door is not opened within two minutes, the Liebert XDF will return to the normal operating point.
OK
If a door is opened, the Liebert XDF will remain in “Open Door Operation” status until all doors are closed. After all doors are closed, a two-minute delay is initiated before
the unit returns to its normal operating setpoint. If a door is opened again within the two-minute
delay, the timer is reset and will restart when the door is closed.
NOTE
The high cabinet temperature alarm is disabled for the period of time that Open Door
Operation is set to YES.)
60
Operation
11.8
Backup Ventilation System
The Liebert XDF is equipped with a backup ventilation system that circulates ambient air through
the Liebert XDF should any component of the cooling system fail or if power is lost. Any alarm that
triggers opening the backup ventilation, does so only after the cabinet temperature exceeds the ambient temperature.
If powered by a UPS, evaporator fans circulate ambient air until the Liebert XDF returns to normal
operation.
Figure 46 Airflow pattern, backup ventilation operation
Self-contained, air-cooled
Liebert XDF shown; vents
and operation apply to all
LiebertXDF models
Evaporator Fans
circulate cooling air
if powered by a UPS
11.9
Heated air returns
Backup Ventilation Air
Intake Vent
Backup Ventilation Air
Exhaust Vent
Liebert XDF Compressor
The Liebert iCOM automatically adjusts the cooling capacity of the digital scroll compressor depending on the heat load in the cabinet.
Sensors near the evaporator fans monitor the cooling airflow and send the data to the Liebert iCOM.
These sensors have setpoints that may be adjusted with the Liebert iCOM control unit to raise or
lower the internal cabinet temperature. For information on changing the setpoints, refer to 11.6 Changing the Liebert XDF’s Default Operating Temperature or call 800-543-2778.
If the supply air temperature drops below the setpoint, Liebert iCOM reduces the compressor’s cooling output accordingly. The evaporator fans will continue to circulate internal cabinet air throughout
the enclosure.
11.10 Uninterruptible Power Supply
The Liebert XDF may be supplied with any of several Liebert UPS units or with no UPS. For integrated/matched models, the UPS and the equipment installed in the Liebert XDF are sized with
matched capacities. A larger UPS, with more battery time, can be obtained, but the connected electronics load should not exceed the Liebert XDF’s cooling capacity.
For Liebert XDF units equipped with a UPS, refer to the UPS manual for UPS operation and specifications.
61
Alarms and Warnings
12.0 ALARMS AND WARNINGS
12.1
General Alarm Information
Whenever there is an alarm or a warning, the display will automatically move to the active alarms
screen. Some alarms will reset automatically and the Liebert XDF will return to normal operation if
the conditions causing the alarm are corrected. Alarms that reset automatically will continue to
sound a buzzer and display a flashing red light to notify the user that an alarm has occurred. If the
conditions causing the alarm no longer exist, the light and buzzer can be stopped by pressing the
alarm key on the keypad.
This section describes the conditions that cause alarms and the alarm reset procedures.
12.2
Alarms
High Head Pressure Alarm
The compressor will turn Off immediately after the high head pressure switch closes.
High Head Pressure at Startup—If a high pressure condition occurs during the first 10 minutes of
operation, the compressor will be turned Off for 10 seconds then will start again (assuming the high
pressure is alleviated) with no alarm indication. This can occur three times within the first 10 minutes of operation. If a high head pressure situation occurs a fourth time, the compressor will be locked
Off. If the compressor is locked Off, call your local Emerson representative.
High Head Pressure During Normal Operation—If the compressor goes into a high head pressure condition after the first 10 minutes of operation, the compressor will turn Off and an alarm will
be activated. If the pressure falls and the high head pressure switch opens, the alarm will reset automatically and the compressor will restart after three minutes. The flashing red light and buzzer
remain active until acknowledged by pressing the alarm key once. If the compressor goes into a high
head pressure condition three times in a rolling 12-hour period, the compressor will be locked Off. If
the compressor is locked Off, call your local Emerson sales representative.
Low Pressure Alarm
Table 14
Coolant pressure settings, psi (kPa)
Low-Pressure
Cut Out
Low-Pressure
Cut In
High-Pressure
Cut Out
35 (241.3)
60 (413.7)
425 (2930.3)
The low-pressure switch is ignored for a period of time after a cold start of the compressor.
NOTE
The period the low-pressure switch is ignored can be programmed between 0 and 5 minutes by
an authorized Emerson service associate. The default is 3 minutes.
If the low-pressure switch opens for less than 5 seconds after the period of time the switch is
ignored, the compressor will continue to run. If the low-pressure switch opens for more than
5 seconds but less than 15 seconds, an alarm will be activated and the low-pressure counter
will increment to 1. The compressor will continue to run, but the flashing red light and audible
alarm will remain active until acknowledged.
The low-pressure alarm has a 12-hour rolling timer. If the low-pressure counter increments to 3
within a rolling 12-hour period, the compressor will be locked Off. The compressor will be allowed to
come back On only if either power is removed from the control or if the low-pressure counter is reset
to 0 by an authorized Emerson service associate.
If the low-pressure switch opens for more than 15 seconds, an alarm will be activated and the compressor will be locked Off. The compressor will be allowed to come back On only if either the power is
removed from the control or if the low-pressure counter is reset to 0 by an authorized Emerson service
associate.
62
Alarms and Warnings
Loss of Compressor Power
A Loss of Compressor Power alarm will be active if the compressor circuit loses power. The compressor will restart automatically if power is restored. The flashing red light and buzzer remain active
until acknowledged by pressing the alarm key once.
Digital Scroll High Temperature Protection
The digital scroll compressor has a built-in head temperature sensor. If the value reaches
268ºF (131ºC), the digital scroll high temperature alarm will be activated and the compressor will be
shut down for 30 minutes. If the sensor falls below its reset temperature during the 30 minute shutdown, the alarm will reset automatically and the compressor will restart at the conclusion of the shutdown period. The flashing red light and buzzer remain active until they are acknowledged by pressing
the alarm key.
If the compressor is turned Off five times in a rolling 4-hour period due to a high scroll temperature,
the compressor will be locked Off. If the compressor is locked Off, call your local Emerson sales representative.
High Cabinet Temperature Alarm
The user can set the high cabinet temperature alarm setpoint under the Set Alarms option in the user
menu. The default setpoint is 90ºF (27.2ºC). If the cabinet temperature exceeds the setpoint, this
alarm becomes active.
If the user desires to change the high cabinet temperature alarm setpoint, Emerson recommends setting it at least 10ºF (5.5°C) higher than the internal cabinet temperature setpoint.
NOTE
If the compressor is On when the cabinet reaches the high cabinet alarm setpoint, the control
will attempt to bring the cabinet temperature down by running the digital scroll compressor at
100% capacity. The control will monitor the cooling inside the cabinet and determine if
sufficient cooling is taking place. If sufficient cooling is occurring, the compressor will continue
to run and there will be no alarm as long as the unit is capable of bringing the cabinet
temperature down to the cabinet temperature setpoint. If the cooling rate is insufficient, the
high cabinet temperature alarm will be activated. The compressor will continue to run as long
as the cabinet temperature is below the ambient temperature. If the cabinet temperature
exceeds the ambient temperature, the compressor will be locked Off and the backup ventilation
will open. The compressor will remain locked Off until the alarm is reset.
The alarm can be reset only if the high temperature condition is resolved and the main power is
reset or the high cabinet temperature counter is reset by an Emerson service associate.
If the compressor is turned Off due to Loss of Compressor Power, Digital Scroll High Temperature, or
High Head Pressure and the cabinet temperature subsequently exceeds the high cabinet temperature
alarm setpoint, the high cabinet temperature alarm will be activated. If the original reason that the
compressor is Off is fixed, the following sequence occurs:
• The control will permit the compressor to run at 100% capacity for 20 seconds and check to see if
sufficient cooling is occurring inside the cabinet.
• If the control determines that sufficient cooling is occurring, the compressor will continue to run
and the control will continue monitoring the cabinet cooling progress. Once the cabinet temperature drops to 2ºF (1.2ºC) above the cabinet setpoint, the high cabinet temperature alarm will reset
automatically and normal operation will resume.
• If the control determines that sufficient cooling is not taking place and the cabinet temperature
exceeds the ambient temperature, the compressor will be locked Off and the backup ventilation
will open.
NOTE
The audible alarm and flashing red light will remain active until the user presses the alarm
key on the control panel.
63
Alarms and Warnings
Compressor Start Counter
Any time the compressor starts, a counter will increment by 1. One hour after a compressor-start
event, the counter will decrement by 1. If the counter exceeds the maximum allowable value within a
rolling one-hour period, the compressor will be locked Off and the Liebert iCOM will display the
alarm Compressor(s) Lockout.
NOTE
The allowable number of compressor starts can be changed in the service menu between 6 and
20 by an authorized Emerson service associate. The default is 15. If the compressor is locked
Off, the only way to reset the alarm is to remove power from the control (the counter is not
stored).
! WARNING
If the compressor-start counter reaches 6, a Compressor Short Cycle warning will be shown on
the unit display, the unit will sound an audible alarm and display a flashing red light.
Sensor Failure Alarm
Four sensors measure the internal cabinet temperature. If all four sensors fail, the display will read
Cabinet Sensor Fail, the red light will flash and the buzzer will sound. A backup sensor will take over
and the unit will continue to run. If this occurs, contact your authorized Emerson representative.
If the backup sensor fails, the display will read Cabinet H-Sensor Fail, the red light will flash and the
buzzer will sound. At this point, the compressor will be locked Off and the backup ventilation will be
activated. If this occurs, contact your authorized Emerson representative.
12.2.1 Backup Ventilation
The Liebert XDF is equipped with backup ventilation that will open when outside air must be brought
in for cooling. In normal operating mode Compressor On, the backup ventilation will be closed. In an
emergency situation Compressor Off or if insufficient cooling is taking place, the backup ventilation
will be opened if the cabinet temperature exceeds the ambient temperature. In certain situations, if
the problem is fixed, the control will close the backup ventilation again and normal operation will
resume.
Five events that can lead to activation of backup ventilation are:
•
•
•
•
•
High Head Pressure
Low Suction Pressure
Loss of Compressor Power
High Cabinet Temperature
Digital Scroll High Temperature
High Head Pressure
If the compressor has been turned Off because of High Head Pressure, the backup ventilation will
open if the cabinet temperature rises to or above the ambient temperature. The backup ventilation
will close if the High Head Pressure is resolved, as long as the compressor has not been locked Off by
High Head lockout. See High Head Pressure Alarm on page 62.
Low Suction Pressure
If the compressor has been turned Off due to Low Suction Pressure, the backup ventilation will open
if the cabinet temperature rises to or above the ambient temperature. The backup ventilation will
close if the Low Pressure is resolved, as long as the compressor has not been locked Off by Low Pressure lockout. See Low Pressure Alarm on page 62.
Loss of Compressor Power
If the compressor has been turned Off due to Loss of Compressor Power, the backup ventilation will
open if the cabinet temperature rises to or above the ambient temperature. The backup ventilation
will close if compressor power is restored.
64
Alarms and Warnings
High Cabinet Temperature
If the cabinet temperature exceeds the High Cabinet Temperature alarm setpoint, the control will run
the compressor at 100% capacity and monitor cooling as described in High Cabinet Temperature
Alarm on page 63. If sufficient cooling is not taking place and the internal cabinet temperature
exceeds the ambient temperature, the compressor will be turned Off and the backup ventilation will
open. If the cabinet temperature exceeds the high cabinet temperature alarm setpoint but the cabinet
temperature is below the ambient temperature, cooling will remain On and the backup ventilation
will remain closed as long as the cabinet temperature remains below the ambient temperature.
Digital Scroll High Temperature
If the compressor is turned Off due to Digital Scroll High Temperature, the backup ventilation will
open if the cabinet temperature rises to or above the ambient temperature. The backup ventilation
will close after 30 minutes if the scroll temperature drops below the trip point and cooling resumes, as
long as the compressor has not been locked Off by Digital Scroll High Temperature Lockout. See Digital Scroll High Temperature Protection on page 63.
Sensor Failure
If the compressor has been turned Off due to Sensor Failure, the backup ventilation will open if the
cabinet temperature rises to or above the ambient temperature. If a Cabinet Sensor Failure occurs,
contact your authorized Emerson representative.
12.3
Warnings
Front Door Ajar—This warning is active if the front door is opened without following the procedure
in 11.7 - Operation With the Door Open. The red light will flash and the buzzer will sound until
acknowledged or the door is closed.
Rear Door Ajar—This warning is active if the rear door is opened without following the procedure in
11.7 - Operation With the Door Open. The red light will flash and the buzzer will sound until
acknowledged or the door is closed.
High Condensate Level—This warning is active if condensate is detected at the condensate switch.
The red light will flash and the buzzer will sound until acknowledged or the condensation is no longer
detected by the condensate switch.
Low Cabinet Temperature—The minimum cabinet temperature is user-settable under the Set
Alarms menu in the user menu. The default setpoint is 64°F (17.8°C). If the cabinet temperature
drops below the setpoint for more than 2 minutes, the red light will flash and a buzzer will be activated. If the cabinet temperature rises above the setpoint, the warning will reset automatically.
NOTE
A history of the last 400 alarms and warnings will be archived under the Event Log menu of
the user menu.
65
Maintenance
13.0 MAINTENANCE
Table 15
Troubleshooting
Problem
Liebert XDF system not
cooling
Cause
Solution
No Power
Confirm unit is plugged in and the building breaker has not
tripped.
Clogged condenser coil
Clean coil. See 13.1 - Periodic Maintenance.
Coolant loss
Verify leak. If coolant system needs repaired, contact
Liebert Technical Support at 800-543-2378.
Airflow is blocked at the intake
or exhaust.
Remove airflow obstructions from the front and rear of the
enclosure. Ensure the cabinet has at least 36" (915mm)
front, rear and overhead clearance. (Water/glycol and
remote condenser models do not require overhead
clearance.) Open Liebert XDF’s doors and let compressor
cool. Plug in Liebert XDF and verify compressor is
energized.
Compressor trips on thermal
overload
Open Liebert XDF doors and let compressor cool. Plug in
Liebert XDF and verify compressor is energized.
Fans blowing warm air
Faulty Compressor
Contact Liebert Technical Support at 800-543-2378.
Water leaking from inside
the cabinet
Cabinet not level or internal
drain line clogged
Ensure that the enclosure rests on a level surface. The
cabinet must be level to ensure proper operation. Verify
condensate drain is attached to drain and the drain line has
the proper pitch (see 5.2.4 - Condensate Drain
Connection).
Excessive vibration or
noise
Defective motor in blower or
shipping damage
Contact Liebert Technical Support at 800-543-2378.
Electronic equipment not
positioned for optimum cabinet
airflow
Rearrange the equipment as illustrated in 5.3 - Equipment
Layout.
Compressor is overloaded
Verify the UPS load does not exceed Liebert XDF’s
capacity. If no UPS, verify equipment load does not exceed
the Liebert XDF’s rating.
Heat not rejected from room
Verify that Liebert XDF is in room with air circulation and
heat rejected from unit is sufficiently removed.
Liebert XDF system not cooling
Confirm unit is plugged in and the building breaker has not
tripped. Check setpoints on Liebert iCOM controller.
Cabinet not sealed
Check cable entry points, and verify doors and side panels
are closed. Reposition wires to prevent air leak, or fix or
replace damaged gaskets.
Audible alarm and cabinet
is excessively hot
Liebert iCOM control module
has detected an abnormal
condition
Silence alarm on the Liebert iCOM module. See solutions
for “Liebert XDF system not cooling,” “Fans blowing warm
air” and “Cabinet is excessively hot causes” to determine
course of action.
Unit goes Off on low
suction pressure during
startup
Low ambient temperature
Change winter start kit time to 5 minutes (default setting is 3
minutes).
Cabinet is excessively hot
13.1
Periodic Maintenance
13.1.1 Maintaining the Self-Contained, Air-Cooled Liebert XDF
The Liebert XDF requires very little maintenance. The Liebert XDFS’s condenser coil must be
inspected periodically to determine the necessary cleaning interval based on conditions at the installation site. Depending on site conditions, the coil may require cleaning as often as twice a month or as
seldom as twice per year. If the coil becomes dirty and clogged, it should be vacuumed with a soft bristle brush or cleaned with compressed air.
13.1.2 Maintaining the Liebert XDF with Remote Condenser
For information on maintaining the remote condenser, refer to the unit’s user manual, SL-10066,
available at the Liebert Web site: www.liebert.com
66
Specifications
14.0 SPECIFICATIONS
Figure 47 Liebert XDF model numbers
Model
Model Type
Cooling
Capacity
Input
Power
UPS
Placeholder
Condensate
Pump
XDF
S
14
1
0
0
0
Liebert X-treme Heat
Density
Foundation Enclosure
1 = 120V-1ph-60HzkW
and 208V-3ph-60Hz
S = Self-Contained, Air-Cooled
W = Water-Cooled
R = Remote Condenser
Table 16
0 = None
1 = Module
Included
= 14kW
0 = None
A = Liebert GXT3-1000
B = Liebert GXT3-1500
C = Liebert GXT3-2000
D = Liebert GXT3-3000
E = Liebert GXT3-700
F = Liebert PS1000RT3
0 = None
G = Liebert PS1500RT3
H = Liebert PS2200RT3
I = Liebert PS3000RT3
K = Liebert GXT3-3000 (*)
L = Liebert GXT2-6000 (*)
(*) 208VAC models
Physical specifications
XDFS141
Self- Contained,
Air-Cooled Units
Dimensions
XDFW141
Water/GlycolCooled Units
XDFR141
Remote Condenser
Air-Cooled Units
Height, in. (mm)
Overall
82-1/4 (2089)
79-3/4 (2026)
Cabinet Only
79-3/4 (2026)
79-3/4 (2026)
Fan Guard
Equipment Rack Area
2-1/2 (57)
N/A
36U
42U
Width, in. (mm)
Overall
34-1/8 (867)
EIA Nominal
19 (483)
Inside Dimension
17-13/16 (452)
Overall
49-1/2 (1257)
Depth, in. (mm)
Mounting Depth, adjustable, minimum
24-3/8 (620)
Mounting Depth, adjustable, maximum
32-11/32 (821)
Weight, lb. (kg)
Cabinet Only
710 (322)
Equipment Capacity
668 (303)
1200 (544)
Sound Power Level, dBA
86
67
79
79
Specifications
Table 17
Electrical specifications
Self- Contained,
Air-cooled Units
Electrical Data
Water/Glycol
Cooled Units
Remote Condenser
Air-Cooled Units
Control & Fan Supply
Voltage
Ph
Hz
Unit FLA
Max Fuse or Circuit Breaker Amps
Min. Supply Circuit Ampacity
Receptacle required
Compressor Supply
Voltage
Ph
Hz
Unit FLA
Max. Fuse or Circuit Breaker Amps
Min. Supply Circuit Ampacity
Receptacle Required
Condensate Pump Amps, Optional
Table 18
120
1
1
60
8.3
15
9.2
NEMA 5-15R
208
3
60
20
35
23.9
208
3
60
16.7
35
20.6
NEMA L21-30R
1
1
Supply Air
Temperature,
°F (°C)
Load, kW
Total Heat
Rejection, kW
95 (35)
77 (25)
14.1
20
Liebert XDFR condenser dimensions
Domestic Packaging
14.1
1
Total heat rejection—Liebert XDFS only
Rating Point,
Ambient
°F (°C)
Table 19
1
60
5.0
15
5.2
Export Packaging
Condenser
Model
Number
of Fans
Weight
lb (kg)
Dimensions
LxWxH, in. (mm)
Volume
ft3 (m3)
Weight
lb (kg)
Dimensions
LxWxH, in. (mm)
Volume
ft3 (m3)
TCSV083
CSL083
1
330 (150)
59x30x51
(1500x760x1300)
52 (1.4)
415 (188)
60x31x52
(1520x790x1320)
56 (1.5
Optional Power Systems
Table 20
UPS performance data
Height
Model Number
Input Power (1 ph)
VA / Watts
In (mm) U
Volts
OPD
(A) Plug
Liebert GXT3-700RT120
700 / 490
3.5 (89) 2
120
15
NEMA 5-15P
Liebert GXT3-1000RT120
1000 / 700
3.5 (89) 2
120
15
NEMA 5-15P
Liebert GXT3-1500RT120
1500 / 1050
3.5 (89) 2
120
15
NEMA 5-15P
Liebert GXT3-2000RT120
2000 / 1400
3.5 (89) 2
120
20
NEMA 5-20P
Liebert GXT3-3000RT120
3000 / 2100
3.5 (89) 2
120
30
NEMA L5-30P
Liebert GXT3-3000RT208
3000/2700W
3.5 (89) 3
280
20
NEMA L6-20P
Liebert GXT2-6000RT-208
6000 / 4200
7 (178) 4
208/120
30
NEMA L14-30P or Hard-Wired
Liebert PS1000RT3-120
1000 / 750
3.5 (89) 2
120
15
NEMA 5-15P
Liebert PS1500RT3-120
1440 / 1080
3.5 (89) 2
120
15
NEMA 5-15P
Liebert PS2200RT3-120
2200 / 1650
3.5 (89) 2
120
15
NEMA L5-30P
Liebert PS3000RT3-120
3000 / 2250
3.5 (89) 2
120
15
NEMA L5-30P
68
Specifications
14.2
Optional Managed Power - Liebert MPH Managed Rack PDUs, Horizontal-Mount
Liebert MPH Managed Rack PDUs are available in 19" rack-mount form. See Table 21 for specifications.
Table 21
Liebert MPH—Rack-mount model numbers and specifications
Input
Part Number
Output
Maximum
Rated Continuous
Amps
kW Phase
Voltage Amps
Plug
Receptacle/Socket
Configuration
Monitoring Level - Basic
MPH-NBR09NXXF30
208-240
30
24
4.9
1
NEMA L6-30
(9) IEC-C13
MPH-NBR09NXXE30
208-240
20
16
3.3
1
NEMA L6-20
(9) IEC-C13
MPH-NBR09AXXD30
120
30
24
2.8
1
NEMA L5-30 (9) NEMA 5-20R T-Slot
MPH-NBR09AXXC30
120
20
16
1.9
1
NEMA L5-20 (9) NEMA 5-20R T-Slot
30
24
4.9
1
NEMA L6-30
(9) IEC-C13
(9) IEC-C13
Monitoring Level - Controlled
MPH-NCR09NXXF30
208-240
MPH-NCR09NXXE30
208-240
20
16
3.3
1
NEMA L6-20
MPH-NCR09AXXD30
120
30
24
2.8
1
NEMA L5-30 (9) NEMA 5-20R T-Slot
MPH-NCR09AXXC30
120
20
16
1.9
1
NEMA L5-20 (9) NEMA 5-20R T-Slot
69
Specifications
70
Ensuring The High Availability
Of Mission-Critical Data And Applications.
Emerson Network Power, the global leader in enabling business-critical
continuity, ensures network resiliency and adaptability through
a family of technologies—including Liebert power and cooling
technologies—that protect and support business-critical systems.
Liebert solutions employ an adaptive architecture that responds
to changes in criticality, density and capacity. Enterprises benefit
from greater IT system availability, operational flexibility and
reduced capital equipment and operating costs.
Technical Support / Service
Web Site
www.liebert.com
Monitoring
liebert.monitoring@emerson.com
800-222-5877
Outside North America: +00800 1155 4499
Single-Phase UPS & Server Cabinets
liebert.upstech@emerson.com
800-222-5877
Outside North America: +00800 1155 4499
Three-Phase UPS & Power Systems
800-543-2378
Outside North America: 614-841-6598
Environmental Systems
800-543-2778
Outside the United States: 614-888-0246
Locations
DATA CENTER SOLUTIONS
For More Information:
(866) 787-3271
Sales@PTSdcs.com
While every precaution has been taken to ensure the accuracy
and completeness of this literature, Liebert Corporation assumes no
responsibility and disclaims all liability for damages resulting from use of
this information or for any errors or omissions.
© 2006 Liebert Corporation
All rights reserved throughout the world. Specifications subject to change
without notice.
® Liebert is a registered trademark of Liebert Corporation.
All names referred to are trademarks
or registered trademarks of their respective owners.
United States
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
Europe
Via Leonardo Da Vinci 8
Zona Industriale Tognana
35028 Piove Di Sacco (PD) Italy
+39 049 9719 111
Fax: +39 049 5841 257
Asia
29/F, The Orient Square Building
F. Ortigas Jr. Road, Ortigas Center
Pasig City 1605
Philippines
+63 2 687 6615
Fax: +63 2 730 9572
SL-17010_REV5_03-10
Emerson Network Power.
The global leader in enabling Business-Critical Continuity™
AC Power
Connectivity
Embedded Computing
Embedded Power
DC Power
Infrastructure Management & Monitoring
Outside Plant
Power Switching & Controls
Precision Cooling
EmersonNetworkPower.com
Racks & Integrated Cabinets
Services
Surge Protection
Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks of Emerson Electric Co. or one of its affiliated companies.
©2006 Emerson Electric Co.