Samsung GE4020 Instruction manual

LENS BUILT INCOLOR CCDCAMERA
INSTRUCTION MANUAL
SOC-4020 SERIES
About this manual
Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.
SALES NETWORK
•
SAMSUNG TECHWIN CO., LTD.
Optics & Digital Imaging Division 145-3, Sangdaewon 1-Dong,
Jungwon-Gu, Sungnam, Kyungki-Do, Korea 462-703
TEL : 82-31-740-8137~41 FAX: 82-31-740-8145
•
SAMSUNG OPTO-ELECTRONICS AMERICA, INC. (SOA)
Closed Circuit Division 40 Seaview Drive, Secaucus NJ 07094,
U.S.A
TEL : (201) 902-0347 FAX: (201) 902-0429
•
SAMSUNG OPTO-ELECTRONICS UK LTD (SOUK)
Samsung House, 1000 Hillswood Drive Hillswood Business
Park Chertsey Surrey KT16 OPS
TEL : 44-(0)1932-45-5308 FAX: 44-(0)1932-45-5325
•
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD (TSOE)
7 Pingchang Rd, Nankai Dist, Tianjin, P.R China
Post Code : 300190
TEL : 86-22-2761-9698 FAX: 86-22-2761-6514
www.samsungtechwin.com
www.samsungcctv.com
P/No. : 6806-0438-01B
VAN 04. 9
SAMSUNG CCD CAMERA
Thank you for purchasing a SAMSUNG CCD CAMERA. Before
operating the camera, confirm the camera model and proper
input power voltage. In order that you can understand this
manual thoroughly, we'll introduce our model description.
SOC-4020 Series (410,000 pixels)
• NTSC models
SOC- 4020ND
SOC- 4020NA
SOC- 4020NDW
SOC- 4020NAW
Model Description
SOC- 4020 X X X
Lens Type
• PAL models
SOC- 4020PD
SOC- 4020PA
SOC- 4020PDW
SOC- 4020PAW
WARNING- TO PREVENT ELECTRIC SHOCK AND RISK OF FIRE HAZARDS,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
INFORMATION - This equipment has been tested and
found to comply with limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference
to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Power Source
Signal System
• Signal System
N
NTSC Model
P
PAL Model
• Power Source
D
DC 12V
A
AC 24V ~
• Lens Type
Blank
3.8~9.5mm
W
2.5~6.0mm
WARNING - Changes or modifications not expressly
approved by the manufacturer could void the user’s authority
to operate the equipment.
CAUTION - To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service
person and should conform to all local codes.
Contents
Features
Auto Iris Vari-focal Lens Built-in
High Sensitivity
The focal length of lens is 3.8 to 9.5mm,
equivalent to 2.5x zoom.(2.5 to 6.0mm,
equivalent to 2.4x zoom) The built-in
lens allows the camera to have a Wider
Dynamic Range, therefore you can use
in various applications.
DSP LSI technology provides best picture
with min illumination of 0.5Lux / F1.2
(30IRE).
Fashionable and Stylish Design
White Balance (ATW)
Fashionable design is best suited to many
modern places moreover silver color adds
luster to that.
ATW function allow the camera to
adjust the white balance automatically
in response to light conditions.
High Resolution
SYNC. System
The horizontal resolution of 480 TV lines
can be achieved by using a high density
CCD having effective 410,000 pixels,
which provides clean, noiseless and
reliable pictures.
You can select INT(Internal Synchronization)
mode or L. L(Linelock Synchronization) mode.
(SOC-4020SERIES)
Precautions
6
Composition
8
Name and Function of Each Part
Front
Back
Bottom
9
9
10
13
Connection
14
14
14
15
Lens
Connecting To Monitor
Connecting To Power
Troubleshooting
17
Specification
18
Backlight Compensation
The backlight compensation technology
allows the camera to find the best picture
conditions in any environment and
automatically gives a necessary light level
compensation, so that you can always
obtain the clear picture, the finest detail
and perfect light contrast.
COLOR CCD CAMERA
4
User’s Manual
COLOR CCD CAMERA
5
User’s Manual
Precautions
Do not install the camera in
extreme temperature conditions.
Do not install or use the camera in an
environment where the humidity is high.
Only use the camera under conditions
where temperatures are between -10˚C
and +50˚C. Be especially careful to provide
ventilation when operating under high
temperatures.
It can cause the image quality to be poor.
Do not install the camera under
unstable lighting conditions.
Do not drop the camera or
subject them to physical shocks.
It can cause malfunctions to occur.
Never keep the camera face to
strong light directly.
It can damage the CCD.
Do not expose the camera to
rain or spill beverage on it.
Do not touch the front lens of
the camera.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that corrode
the electronic components.
Notes
Severe lighting change or flicker can
cause the camera to work improperly.
COLOR CCD CAMERA
6
It is one of the most important parts of
the camera. Be careful not to be stained
by fingerprint.
User’s Manual
• If the camera is exposed to spotlight or object reflecting strong light, smear or
blooming may occur.
• Please check that the power satisfies the normal specification before connecting
the camera.
COLOR CCD CAMERA
7
User’s Manual
Composition
Name and Function of Each Part
Front
1. Color CCD Camera SOC-4020
2. Instruction Manual
Lens Built-in
Vari-focal Lens built-in camera.
Control Cover
Used to access focus or zoom handle. After access, be sure to close it.
Focus Handle
Used to provide for accurate focusing of an object within the lens field of view.
Zoom Handle
Used to adjust zoom magnification by turning.
COLOR CCD CAMERA
8
User’s Manual
COLOR CCD CAMERA
9
User’s Manual
Name and Function of Each Part
V. PHASE Adjustment V.R: AC type
If the camera is to be used in the LL mode, the vertical phase may require
adjustment to synchronize the vertical phase of the camera with other camera
in the system. Make this adjustment when the vertical phase of the camera
does not match with other cameras or systems. For correct adjustment, use a
multi - channel oscilloscope. The V. PHASE adjustment can be readjusted.
Back
Notes
• This adjustment is necessary only when linelock is performed.
• There is no V. PHASE adjustment VR on the rear of DC power type.
Power Input Terminal
Used to connect AC/DC power source.
Power Lamp
The power lamp turns on when power is properly supplied.
* This diagram is based on SOC-4020Series
Video Out Jack
Connect to the video input connector of monitor. This jack outputs a
composite video signal. Use a coaxial cable for connection.
DC Level Adjustment V.R
Used to adjust video output level of DC driven auto iris lens. When the
brightness control of the monitor does not operate correctly, you can get the
optimum picture by controlling the DC level of camera.
Monitor Picture
To make it brighter
Adjustment direction
Turn clockwise
COLOR CCD CAMERA
Monitor Picture
To make it darker
10 User’s Manual
Adjustment direction
Turn counterclockwise
Function Selection Switch
* Use the select switches on the rear of camera.
(1) BLC(Backlight Compensation) ON/OFF Switch
This switch improves an image that is darkened because of backlighting.
When the lighting source is in the rear of an object, the object might be seen
somewhat dark. If you want to see the object clearly, turn this switch ON.
The effective area where backlight compensation is activate is fixed in the
center of the screen.
COLOR CCD CAMERA
11 User’s Manual
Name and Function of Each Part
(2) White Balance Control Mode
• ATW(Auto Tracing White balance): The camera automatically controls the
white balance in any environment.
• AWC(Auto White balance Control): The white balance is automatically
adjusted in a specific environment.
Bottom
(3) Sharpness
The switch emphasize the sharpness. To soften the edge turn this switch off.
(4) Flickerless
Flickerless function. In this function, electronic shutter is fixed in 1/100sec
(1/120sec: PAL model). FL function can compensate the flicker caused by
power frequency, but set OFF in the area not using a 60Hz (50Hz: PAL
model) AC Power.
(5) INT/LL Switch: SOC-4020Series
Used to choose INT or LL mode.
• INT(Internal) mode : The camera may be operated independently with its
internal crystal control.
• LL(Linelock) mode : It synchronizes the video signal between cameras using
the frequency of the AC power supply without external synchronous generator.
(6) Not Used
Tripod Mounting Hole
Used to install the camera on an optional tripod.
The tripod must be equipped with the screw
specified as shown below.
Notes
L
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
• The LL mode can be used in the areas of 60Hz(NTSC models), 50Hz(PAL models).
You can remove and install this bracket on the top of
the camera. You must use the supplied screw or the
equivalent (within 6mm). If not, the bracket may not
be fixed properly.
COLOR CCD CAMERA
12 User’s Manual
COLOR CCD CAMERA
13 User’s Manual
Connection
Connecting to Power
LENS
The DC lens is supplied with this camera.
Notes
• If the lens is marked with fingerprints or other marks, the image quality might be poor.
• It is recommended to use the built-in iris lens to improve the image quality under low
illumination.
Each model has different power specification, please check the name of the model
and power specification before connecting to power source.
Please refer to the sticker identifying the model, which is attached on the product,
for power specification.
For DC Power Type
• The wire is polarized. Be careful of polarity.
Connecting to Monitor
• Use DC 12V
power source for SOC-4020SERIES
Connect the VIDEO out jack to the monitor video in jack.
CCD Camera
Monitor
• As the connecting method varies with the instruments, refer to the manual
supplied with the instrument.
• Connect the cable after power is turned off.
• Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate device.
CCD Camera
Intermediate
End monitor
Resistance of copper wire [at 20C˚ (68˚F)]
#24(0.22mm2)
#22(0.33mm2)
#20(0.52mm2)
#18(0.83mm2)
Resistance ( Ω / m)
0.078
0.050
0.030
0.018
Voltage Drop (V/m)
0.028
0.018
0.011
0.006
Copper wire size (AWG)
• As voltage may drop according to the length of electric cord as above table, a
camera may malfunction if too long output line of adaptor is connected to the
camera.
* Voltage for camera operation: DC 12V ± 10%
* Voltage drops on above table are variable according to types of electric cord and makers.
COLOR CCD CAMERA
14 User’s Manual
COLOR CCD CAMERA
15 User’s Manual
Connection
Troubleshooting
For AC Power Type
• The wire is non-polarized.
• Use AC24V ~ 60Hz power source for SOC-4020NA/W
• Use AC24V ~ 50Hz power source for SOC-4020PA/W
If you have trouble operating your camera, refer to the following table. If the
guidelines do not enable you to solve the problem, contact an authorized
technician.
Problem
Solution
Nothing appears on
the screen.
• Check that the power cord and line connection
between the camera and monitor are fixed properly.
• Check that you have properly connected VIDEO
cable to the camera VIDEO output jack.
The image on the
screen is dim.
• Is lens stained with dirt? Clean your lens with soft,
clean cloth.
• Set the monitor to proper condition.
• If the camera is exposed to too strong light, change
the camera position.
• Adjust the lens’ focus properly.
The image on the
screen is dark.
• Adjust the contrast feature of the monitor.
• If you have an intermediate device, set the 75Ω / Hi-z
properly. (refer to page 14)
• Adjust DC Level, VR Level properly (refer to page 10)
The camera is not working
properly, and the surface
of the camera is hot.
• Check that you have properly connected the camera
to an appropriate power source. (refer to page 15)
The image on the
screen flickers.
• Is the camera facing to direct sunlight or fluoresent
lighting? Change the camera position.
L/L mode isn’t able to
be selected.
• Have you connected your camera to DC power
source? Connect it to AC power source.
(SOC-4020Series)
Notes
• Be sure to connect power after all the installation is done.
• Note that AC adaptor is not supplied with camera.
• Use only AC 24V UL listed class 2 power supply.
• Since the wire of DC power type is polarized, be careful when connecting it.
• Do not use power sources other than that specified.
• To prevent fire or electric shock hazard, use a UL listed cable (VW-1, Style 1007).
COLOR CCD CAMERA
16 User’s Manual
COLOR CCD CAMERA
17 User’s Manual
DECLARATION OF CONFORMITY
Specifications
Application of Council Directive(s)
Item
SOC-4020NA/W SOC-4020ND/W SOC-4020PA/W SOC-4020PD/W
Power Source
Power Consumption
AC 24V, 60Hz
DC 12V
3.5W (Max)
2.5W (Max)
INT/LL Selectable
Synchronization
AC 24V, 50Hz
DC 12V
3.5W (Max)
2.5W (Max)
INT/LL Selectable
INT
(0~270˚ Adjustable)
SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
INT
KYUNGNAM, KOREA, 641-120
(0~270˚ Adjustable)
European Representative Name
1/3” Color Interline-Transfer CCD
Image Pick-up Device
Total Pixels
816(H) x 494(V)
798(H) x 584(V)
European Representative Address
Effective Pixels
771(H) x 492(V)
753(H) x 582(V)
Equipment Type/Environment
SOC-4020Series
0.5Lux / F1.2 (30IRE)
Beginning Serial NO.
S3900001
480 TV Line
Year of Manufacture
2003. 9. 1
Conformance to
EN 50081-1 : 1992
Resolution
Video Output
VBS ; 1Vp-p, 75Ωunbalanced
Scanning Frequency
15.734KHz(H) / 60Hz(V)
15.625KHz(H) / 50Hz(V)
AGC
EMC-Directive 89/336 EEC and 92/31/EEC
Built in
White Balance
EN 50130-4 : 1996
ATW / AWC Selectable
BLC Function
ON / OFF Selectable
Sharpness
High / Normal Selectable
Flickerless
ON / OFF Selectable (ON: 1/100sec)
We, the undersigned, hereby declare that the equipment specified above conforms
ON / OFF Selectable (ON: 1/120sec)
to the above Directive(s).
Lens Type
Blank : X2.5 vari-focal, f=3.8~9.5, F=1:1.3~2.0
W Series : X2.4 vari-focal, f=2.5~6.0, F=1:1.3~2.0
S/N Ratio
more than 48dB (weight ON)
Signature
-10˚C ~ +50˚C [14˚F~122˚F] / 30% ~ 90%RH
Operating Temperature
Dimention
62(W) x 58(H) x 165(D)mm
300g
290g
* Design and specifications are subject to change without notice
COLOR CCD CAMERA
18 User’s Manual
300g
SAMSUNG TECHWIN CO., LTD
Legal Representative in Europe
Full Name
YOUNG TAEK SON
Full Name
Position
QUALITY CONTROL MANAGER
Position
Place
CHANGWON, KOREA
Place
Date
2003. 9. 1
Date
Manufacturer
(DC Iris Lens adjustable)
Weight (Without Lens)
CCTV Camera
Model Name
2:1 Interlace
Scanning
Min. Illumination
89 / 336 / EEC
Manufacturer's Name
290g
Signature