Ed.
00
OfficeServ DataView
User Guide
04. 2005.
COPYRIGHT
This guide is proprietary to SAMSUNG Electronics Co., Ltd. and is protected by copyright.
No information contained herein may be copied, translated, transcribed or duplicated for any
commercial purposes or disclosed to third parties in any form without the prior written consent of
SAMSUNG Electronics Co., Ltd.
TRADEMARKS
is the trademark of SAMSUNG Electronics Co., Ltd.
Product names mentioned in this document may be trademarks and/or registered trademarks of
their respective companies.
This guide should be read before the installation and operation, and the operator should correctly
install and operate the product by using this guide.
This guide may be changed for the system improvement, standardization and other technical reasons
without prior notice.
For further information on the updated guide or have a question for the content of guide, contact the
address or homepage below.
Address: Document Center 2nd Floor IT Center. Dong-Suwon P.O. Box 105, 416, Maetan-3dong
Yeongtong-gu, Suwon-si, Gyeonggi-do, Korea 442-600
Homepage: http://www.samsungdocs.com
©2004 SAMSUNG Electronics Co., Ltd.
All rights reserved.
OfficeServ DataView User Guide
INTRODUCTION
Purpose
This guide is the user’s guide of OfficeServ DataView, which provides data on
monitoring, and statistics for the OfficeServ system. This guide provides
information on the main and detailed functions of OfficeServ DataView, and
describes how to install and use OfficeServ DataView.
Document Content and Organization
This guide consists of 8 chapters and 1 annexes as follows:
CHAPTER 1. Overview of OfficeServ DataView
This chapter provides an overview of OfficeServ DataView and its functions.
CHAPTER 2. OfficeServ DataView Installation
This chapter provides information on checkpoints and an action that needs to
be performed before installing OfficeServ DataView and describes how to
install the system.
CHAPTER 3. OfficeServ DataView Menus
This chapter describes the components and settings of OfficeServ DataView
and method of using this program.
CHAPTER 4. Statistics
This chapter describes the OfficeServ statistics function supported by
OfficeServ DataView.
© SAMSUNG Electronics Co., Ltd.
I
Ошибка! Стиль не определен.
CHAPTER 5. Monitoring
This chapter describes the OfficeServ system monitoring function supported
by OfficeServ DataView.
CHAPTER 6. Scheduled Report
This chapter describes the daily/weekly/monthly scheduled report function
supported by OfficeServ DataView.
CHAPTER 7. Troubleshooting
This chapter describes how to troubleshoot the problems that may occur while
installing or using OfficeServ DataView.
ANNEX A. Abbreviation
Describes the acronyms used in this guide.
Conventions
The following special paragraphs are used in this document to point out
information that must be read. This information may be set-off from the
surrounding text, but is always preceded by a bold title in capital letters.
CHECKPOINT
Provides the operator with checkpoints for stable system
operation.
NOTE
Indicates additional information as a reference.
II
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Reference
OfficeServ 500/iDCS 500 System Description
This document describes the main functions of OfficeServ 500/iDCS 500 and
method of configuring its cabinets and boards.
OfficeServ 500/iDCS 500 Installation Manual
This document describes the hardware of OfficeServ 500/iDCS 500 and
method of installing the program.
OfficeServ 500/iDCS 500 Programming Manual
This document describes the MMC list for system settings and method of
MMC settings.
OfficeServ Link User’s Guide
This document describes the functions of OfficeServ Link and methods of
installing and using the program.
Revision History
EDITION
DATE OF ISSUE
REMARKS
00
10. 2004
Original
01
01. 2005
Image Update
02
04. 2005
V1.0.0.2
© SAMSUNG Electronics Co., Ltd.
III
Ошибка! Стиль не определен.
This page is intentionally left blank.
IV
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide
TABLE OF CONTENTS
INTRODUCTION
I
Purpose .......................................................................................................................... I
Document Content and Organization ............................................................................. I
Conventions................................................................................................................... II
Reference ..................................................................................................................... III
Revision History............................................................................................................ III
CHAPTER 1. Overview of OfficeServ DataView
1
Overview of OfficeServ DataView ..................................................................................... 1
System Requirements........................................................................................................ 3
Functions of OfficeServ DataView .................................................................................... 4
CHAPTER 2. OfficeServ DataView Installation
5
Before Installation .............................................................................................................. 5
Procedure for OfficeServ DataView Setup ....................................................................... 6
CHAPTER 3. OfficeServ DataView Menus
11
Components of OfficeServ DataView.............................................................................. 11
Scheduler .................................................................................................................... 12
Data Collector .............................................................................................................. 23
Data Manager .............................................................................................................. 26
Starting OfficeServ DataView .......................................................................................... 28
Main Window .................................................................................................................... 30
Menus ................................................................................................................................ 32
Configuration.................................................................................................................... 33
User ............................................................................................................................. 33
System Info.................................................................................................................. 35
Scheduled Report........................................................................................................ 39
© SAMSUNG Electronics Co., Ltd.
V
TABLE OF CONTENTS
Personalize .................................................................................................................. 42
CHAPTER 4. Statistics
45
Statistics Window Layout ................................................................................................ 45
Selecting a Statistics Item................................................................................................ 47
Statistics Item ................................................................................................................... 48
Additional Menus.............................................................................................................. 49
Print ............................................................................................................................. 49
Export to Excel............................................................................................................. 50
Execution Option Setup ................................................................................................... 52
Trunk Statistics ................................................................................................................. 52
Trunk Overall Statistics ................................................................................................ 53
Trunk Incoming Statistics ............................................................................................. 55
Trunk Outgoing Statistics ............................................................................................. 57
Trunk Distribution Statistics.......................................................................................... 59
Trunk Incoming Distribution Statistics .......................................................................... 61
Trunk Outgoing Distribution Statistics .......................................................................... 63
Trunk Incoming Fail Statistics ...................................................................................... 65
Trunk Outgoing Fail Statistics ...................................................................................... 67
Trunk Outgoing Statistics by Group ............................................................................. 68
Trunk Group Outgoing Statistics .................................................................................. 70
Trunk Port Statistics ..................................................................................................... 72
Trunk Abandoned Call List ........................................................................................... 74
Station Statistics............................................................................................................... 75
Station Overall Statistics .............................................................................................. 75
Station Incoming Statistics ........................................................................................... 77
Station Outgoing Statistics ........................................................................................... 79
Station Incoming Detailed Statistics ............................................................................. 81
Station Outgoing Detailed Statistics ............................................................................. 82
Station Outgoing Fail Statistics .................................................................................... 83
Station Tried Features Statistics................................................................................... 85
Station Incoming Statistics by Group............................................................................ 86
Station Group Incoming Statistics ................................................................................ 88
Station Group Inbound Detailed Statistics.................................................................... 90
Station Port Statistics ................................................................................................... 92
UCD Statistics ................................................................................................................... 94
VI
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
UCD Overall Incoming Statistics.................................................................................. 94
UCD Incoming Statistics by Group .............................................................................. 97
UCD Group Incoming Statistics ................................................................................... 99
UCD Overall Agent Incoming Statistics...................................................................... 101
UCD Agent Incoming Statistics by Group .................................................................. 102
UCD Group Agent Incoming Statistics ....................................................................... 104
UCD Agent Detailed Statistics ................................................................................... 106
UCD Call Distribution Statistics.................................................................................. 108
UCD Call Distribution Stat. by Group ......................................................................... 109
UCD Wait Distribution Statistics..................................................................................111
UCD Wait Distribution Stat. by Group ........................................................................ 113
UCD Group Abandoned Call List ............................................................................... 115
Operator Statistics ......................................................................................................... 117
Operator Group Overall Statistics .............................................................................. 117
Operator Group Detailed Statistics ............................................................................ 120
Operator Distribution Statistics .................................................................................. 122
Operator Distribution Stat. by Ring Plan .................................................................... 124
Operator Port Statistics by Port ................................................................................. 126
Operator Port Detailed Stat. by Port .......................................................................... 128
Miscellaneous................................................................................................................. 130
VMAA/AA/Cadence Group Statistics ......................................................................... 130
VMAA/AA/Cadence Xfer Fail Statistics ...................................................................... 133
Statistics by DID ........................................................................................................ 134
Detailed DID Statistics ............................................................................................... 135
CHAPTER 5. Monitoring
137
Monitoring Window Layout ........................................................................................... 137
Selecting a Monitoring Item........................................................................................... 139
Monitoring Item .............................................................................................................. 139
Additional Menus ........................................................................................................... 140
New Page .................................................................................................................. 140
Trunk Monitoring ............................................................................................................ 141
Trunk Group Status.................................................................................................... 141
Trunk Group Port Status ............................................................................................ 142
Trunk Port Status by Scope ....................................................................................... 144
Trunk Port Status by Time ......................................................................................... 145
© SAMSUNG Electronics Co., Ltd.
VII
TABLE OF CONTENTS
Station Monitoring .......................................................................................................... 146
Station Group Status .................................................................................................. 146
Station Group Port Status .......................................................................................... 148
Station Port Status by Scope ..................................................................................... 150
Station Port Status by Time........................................................................................ 151
UCD Monitoring .............................................................................................................. 152
UCD Call Status ......................................................................................................... 152
UCD Agent Status ...................................................................................................... 154
UCD Group Agent Status ........................................................................................... 155
Miscellaneous ................................................................................................................. 156
Operator Group Status............................................................................................... 156
AA/VMAA Group Status ............................................................................................. 157
AA/VMAA Group Port Status...................................................................................... 159
Wall board.................................................................................................................. 160
CHAPTER 6. Scheduled Report
163
Scheduled Report Window Layout................................................................................ 163
CHAPTER 7. Troubleshooting
165
ODBC Version Error ....................................................................................................... 165
I cannot open the monitoring pages!............................................................................ 166
I cannot save the Scheduled Report options!.............................................................. 168
I cannot add/delete/modify accounts!........................................................................... 171
I cannot save [Personalize] configurations!................................................................. 173
I cannot save the exported excel report ! ..................................................................... 174
ANNEX A. Abbreviation
VIII
177
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide
CHAPTER 1. Overview of OfficeServ
DataView
This chapter provides an overview of OfficeServ DataView and describes its functions and system
requirements.
Overview of OfficeServ DataView
OfficeServ DataView is a monitoring/statistics application for OfficeServ, and
provides information on current system usage, cumulative statistics on usage,
and system failures through web-based user interfaces.
One of the monitoring, and statistics functions can be selectively installed on
OfficeServ DataView.
OfficeServ DataView has the following components: the data collection
module that analyzes the call events generated from the switching system, the
data processing module that calculates statistics on each item by using the
collected data and saves the statistical data in the database, and the report
module that provides you with web-based windows. The modules are called
Data Collector, Data Manager, and Reporter respectively.
To use OfficeServ DataView, OfficeServ Link must be installed. OfficeServ
Link delivers the events generated from the OfficeServ system to each
additional program, and delivers commands from the additional programs to
the OfficeServ system.
The OfficeServ system, OfficeServ Link, and OfficeServ DataView are
available in Intranet, and transfer or receive data over TCP/IP(Trnasmission
Control Protocol/Internet Protocol).
© SAMSUNG Electronics Co., Ltd.
1
Ошибка! Стиль не определен.
Network configuration of OfficeServ DataView, OfficeServ Link, and the
OfficeServ system is shown in the figure below:
OfficeServ DataView
TCP/IP
TCP/IP
Intranet
OfficeServ Link
OfficeServ
Web Client #1
•
•
•
Web Client #n
2
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
System Requirements
OfficeServ DataView inter-works with the OfficeServ system. Check the
following before installing OfficeServ DataView:
Category
Operating System
Specification
Windows 2000 Series;
Windows XP Professional;
Windows 2003 Series; or NTFS File Format
Processor(CPU)
Pentium IV 1 GHz or higher
(Requirements for CPU and memory depend on number of
lines and maximum traffic.)
Memory
More than 512 Mbyte
Network Interface Card
10/100 BASE-T
Database
If you use SQL Server, Microsoft SQL Server 2000 or higher
is required.
If you use MDB, there are no special requirements except
that the database file size is limited to 2 GB.
© SAMSUNG Electronics Co., Ltd.
3
Ошибка! Стиль не определен.
Functions of OfficeServ DataView
OfficeServ DataView supports the functions below:
Trunk/Station Monitoring
OfficeServ DataView monitors lines in a trunk or station group as well as call
status. Also, OfficeServ DataView monitors trunks or stations for specified
phone numbers and checks if a trunk or station has exceeded a time limit for
use. Monitoring can be performed depending on group characteristics such as
a UCD(Universal Call Distribution) group, attendant group, and VMAA(Voice
Mail Automated Attendant) group. OfficeServ DataView supports the
wallboard function that traces real-time changes in a selected value, which is
equal to number of waiting calls in a UCD group.
Statistics on Intercom/External Calls
OfficeServ DataView provides statistics on intercom or external calls by node or
group. OfficeServ DataView displays statistics depending on characteristics of a
UCD group, attendant group, and VMAA group. Also, statistics on each DID(Direct
Inward Dialing) are provided. The minimum unit of call statistics is 15 minutes.
Report
Select the [Scheduled Report] submenu from the [Configuration] menu of
OfficeServ DataView to create a report for a specified period of time at a
specified time. OfficeServ DataView can create a scheduled report for trunk,
station, or the UCD group and can back up or delete a report as well.
Database Backup
You can monitor size of a database file from OfficeServ DataView and can
back up the file in the database. If the database space reaches the threshold
value, OfficeServ DataView will display a warning message.
OfficeServ DataView Management
OfficeServ DataView can monitor operation status of each module. OfficeServ
DataView provides a user interface, which enables individual stop/execution
and batch stop/execution easily.
4
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide
CHAPTER 2. OfficeServ DataView
Installation
This chapter provides information on checkpoints and an action that needs to be performed before
installing OfficeServ DataView and describes how to install the system.
Before Installation
Check the following before installing OfficeServ DataView:
Obtaining a Valid License Number of OfficeServ DataView
A valid license number must be registered in order to operate OfficeServ
DataView properly. A license number can be obtained from the reseller or
Samsung dealer of OfficeServ DataView. The number should be entered in a
PC where OfficeServ Link is installed. If a license number is not registered,
OfficeServ DataView will not operate properly.
Checking IP Address of OfficeServ Link
You should be aware of the IP(Internet Protocol) address of the PC where
OfficeServ Link is installed before installing OfficeServ DataView. Contact
the OfficeServ Link manager or OfficeServ system administrator and check
the IP address of OfficeServ Link first.
Checking Specification of the PC Where OfficeServ DataView will
be Installed
OfficeServ DataView is installed on a PC typically. Check the PC where
OfficeServ Link will be installed and operating system, processor, and
memory of the PC. For detailed information on system requirements, refer to
‘System Requirements’ of ‘CHAPTER 1. Overview of OfficeServ DataView’.
© SAMSUNG Electronics Co., Ltd.
5
Ошибка! Стиль не определен.
Procedure for OfficeServ DataView Setup
Follow the steps below to install OfficeServ DataView.
OfficeServ DataView is installed in the ‘Program Files\..\Samsung
Electronics\OfficeServ DataView’ folder by default.
1.
2.
3.
6
Double click ‘OfficeServDataView.exe’ by using a CD for OfficeServ
DataView setup or double click a downloaded ‘OfficeServDataView.exe’.
Once the <InstallShield Wizard> window appears, select a country and
click [Next>].
Read the license agreement from the <License Agreement> window
carefully, and then click [Next>].
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
4.
5.
Once the <Setup Type> window appears, select a setup type and click
[Next>].
Once the <Ready to Install the Program> window appears, click [Install].
© SAMSUNG Electronics Co., Ltd.
7
Ошибка! Стиль не определен.
6.
7.
Select a database to be used for OfficeServ DataView from the
<Database Type> window and click [Next>].
If you select SQL(Structured Query Language) Server, a window that
prompts you to enter information on SQL Server will be displayed. Enter
the SQL Server name or IP address, user ID, and password, and then
click [Next>].
If You Select Microsoft Access Driver(*.mdb)
Step 7 will be skipped if you select Microsoft Access Driver(*.mdb).
8
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
8.
Select a location where database will be installed from the <Database
Location for SQL Server> window. Database can be installed in a folder
shared with My Computer or Network Computer.
Then, specify a folder.
9.
Setup is in progress as the <Setup Status> window appears.
© SAMSUNG Electronics Co., Ltd.
9
Ошибка! Стиль не определен.
10. Once OfficeServ DataView setup is completed, click [Finish].
Troubleshooting
If OfficeServ DataView does not operate properly after OfficeServ DataView
setup, refer to ‘CHAPTER 8. Troubleshooting.’
10
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide
CHAPTER 3. OfficeServ DataView Menus
This chapter describes the menus and windows of OfficeServ DataView.
Components of OfficeServ DataView
OfficeServ DataView is configured with server modules such as Data
Collector, Data Manager, and Scheduler as well as a web program that allows
you to view data on monitoring, and statistics.
OfficeServ System
As shown in the above figure, the server modules of OfficeServ
DataView exchanges data with the OfficeServ system through OfficeServ
OfficeServ Link
Link. Reporter
and the other modules exchange data through the
COM(Component Object Model) interface and database.
Data Collector
Config
COM
Data Manager
Monitor
COM
Web
Client
IIS
Reporter
Web
Client
•
•
•
•
•
Web
Client
Database
© SAMSUNG Electronics Co., Ltd.
11
Ошибка! Стиль не определен.
You can view the data on monitoring, or statistics provided by OfficeServ
DataView through a web service provided by IIS(Internet Information Server)
of Windows OS(Operating System).
Scheduler
Scheduler of OfficeServ DataView allows you to configure, start, or stop the
server modules of OfficeServ DataView and to monitor the operation of
OfficeServ DataView.
Scheduler verifies settings of time and scheduled report periodically and
requests for creating a scheduled report. Also, Scheduler backs up a scheduled
report.
Scheduler monitors size of database files and backs up the files.
Scheduler must be executed to perform the scheduled report function.
Select [Start] Æ [Programs] Æ [OfficeServ DataView] Æ [Scheduler] to
execute Scheduler.
Select [Exit] from the [File] menu or the system tray menus to quit Scheduler.
Then, the Scheduler window will disappear. However, it does not mean that the
program has ended, and an icon is displayed in the system tray.
Scheduler Windows
Status Window
Upon starting Scheduler, the window below will appear:
12
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
© SAMSUNG Electronics Co., Ltd.
13
Ошибка! Стиль не определен.
If a module stops, [Start] will be enabled. If a module runs, [Stop] will be
enabled. If a module stops, the icons will be displayed blurrily. If a module
runs, the icons will be displayed vividly. If a server module does not respond
to a connection message received from Scheduler for a given period of time, a
warning icon will be displayed. In such a case, check operation log of the
server module and take an appropriate action such as restart.
Select whether to display the Data Manager icon in the system tray by using
the checkbox at the right of the Data Manager icon. The Data Manager has no
user interface.
If a server module does not operate, you can click [Start All] to start Data
Collector, and Data Manager simultaneously. Also, click [Stop All] to stop all
operating server modules.
If an error in a web service occurs, click [IIS Reset] to restart IIS. In such a
case, all of the currently established sessions are disconnected.
Database Window
Click the [Database] tab. Then, the window below will appear:
77
14
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
The database window displays the file size, average growth per hour, and
estimated amount of time it will take for the database file size to reach the
threshold value of the current call log database, and statistical database.
Click [Backup] to back up and empty database. If Data Manager runs, the call
log database and statistical database cannot be backed up. Therefore, you
should stop the module first, and then back up the module.
Click [Backup]. The dialog box below will appear:
Enter a description of backup, backup path, and file name. Then, click [OK].
© SAMSUNG Electronics Co., Ltd.
15
Ошибка! Стиль не определен.
Schedule Window
Select the [Schedule] tab to manage the current settings of a scheduled report
and a scheduled report file.
The Schedules frame displays information on the current scheduled report.
The Folder Information frame displays information(e.g., number of the files
saved in a folder and total of file size) on the folder where a scheduled report
is saved.
16
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Click each report button of the Folder Information frame to back up or delete a
scheduled report saved in a report folder.
Select a file you want to back up or delete, and then click [Backup] or [Delete].
If you want to back up a file, the selected file will be deleted from the
scheduled report folder and will be saved in the folder selected for backup.
Scheduler Menus
File Menu
Select [Exit] from the File menu to quit Scheduler.
Scheduled Report Function
Once Scheduler quits, a scheduled report will not be created. If you want to
perform the scheduled report function, Scheduler must be executed.
© SAMSUNG Electronics Co., Ltd.
17
Ошибка! Стиль не определен.
Configuration Menu
The Configuration menu has the submenus as shown in the figure below:
Connection
Select [Connection]. Then, the dialog box below will appear:
Each field is described below:
Item
Description
Host Name/
Enter the IP address of the PC where OfficeServ DataView is
Address
installed or the NetBIOS name. If an invalid IP address or NetBIOS
name is entered, Data Manager cannot be connected to Data
Collector and the home page of OfficeServ DataView will not be
displayed properly.
OfficeServ Link
Enter the IP address of OfficeServ Link and the port number for
Connection
connection.
If you are not aware of the port number, contact the OfficeServ Link
manager and enter a valid value.
18
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Item
Description
OfficeServ
Specify a port to be connected to Data Manager. If another
DataView Listen
application already uses Port Number. 5001 on a computer where
Port
OfficeServ DataView is installed, the default value, 5001, should be
changed to another value.
Database
Select [Database] to enter information on database to be used in OfficeServ
DataView.
You can select database you want from MDB(Multimedia Database) and SQL
Server while installing OfficeServ DataView. Required database options
depend on database type.
Changes in Database Type
The database type selected before OfficeServ DataView setup cannot be
changed.
SQL Server:
Select [SQL Server] from the Database submenu. Then, the dialog box below
will appear:
© SAMSUNG Electronics Co., Ltd.
19
Ошибка! Стиль не определен.
Each field is described below:
Item
Description
Data Source
Enter the name or IP address of SQL Server.
User ID
Enter the user ID for connection.
Password/Password
Enter password of the user ID entered in [User ID].
Confirm
Enter the password once again for confirmation.
Threshold(MB)
Enter the threshold value of database file size.
MDB:
Select [MDB] from the Database submenu. Then, the dialog box below will
appear:
Each field is described below:
Item
Description
Path
Select a folder where a MDB file for OfficeServ DataView will be located.
Threshold(MB)
Enter the threshold value of database file size. Data of more than
2 GB cannot be saved in MDB. If the file size exceeds 2 GB, an error
will occur and data will not be saved. Set the threshold value to less
than 2 GB(2,048 MB) and check the data provided by the [Database]
tab of Scheduler frequently to back up the database.
20
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Log Records
[Log Records] allows you to select a type of a call log to be saved in the
database. If you save all types of logs in the database, log records will increase
and bottleneck may occur while the database is operating.
To prevent OfficeServ DataView from being degraded due to bottleneck, limit
number of logs to be saved.
Select [Log Records]. Then, the dialog box below will appear:
Select the checkbox of a log type and click [OK].
© SAMSUNG Electronics Co., Ltd.
21
Ошибка! Стиль не определен.
Operation Logs
The [Operation Logs] option is divided into Data Collector, and Data Manager.
Select one to perform settings for saving operation logs of the selected module.
If the selected module is enabled, the window that prompts you to set an
operation log of the module will appear.
If the selected module is not enabled, the window that prompts you to set an
operation log provided by Scheduler will appear as shown in the figure below:
If the frames for the operating one from Data Collector, and Data Manager
will be disabled. If a module is enabled, the Path frame cannot be changed.
22
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Data Collector
Data Collector collects events for calls from OfficeServ Link to create a call
log and to deliver the call log to Data Manager. Also, Data Collector manages
configuration data on the OfficeServ system and current status of the system.
Data Collector must operate properly for proper operation of OfficeServ
DataView.
Data Collector Window
Run Data Collector. Then, the window below will appear:
The LEDs(Light Emitting Diodes) at the right of OfficeServ Link and
DataView Manager indicate connection status.
LED
Description
(Dark green)
Not connected
(Light green)
Connected properly
(Pink)
Data Collector has downloaded the configuration data from the
OfficeServ system and is being initialized. Or, a connection error has
occurred.
The buttons of Data Collector Window are described below:
Button
Description
Config
Configures Data Collector.
Run/Stop
Click [Run] to access OfficeServ Link and to download the configuration
data on the OfficeServ system, initialize Data Collector, and then start
operation. Once operation starts properly, [Run] is disabled while [Stop]
is enabled.
Click [Stop] to stop operation. A connection to both Data Collector and
OfficeServ Link will stop.
© SAMSUNG Electronics Co., Ltd.
23
Ошибка! Стиль не определен.
Button
Monitor
Description
Click this button to open a window that allows you to monitor the memory
space managed by Data Collector. Regular users do not use this function
because this button is used for tracing a problem.
Quit
Quit Data Collector.
Data Collector Configuration
Click the [Config] button from the Data Collector window to configure Data
Collector.
24
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Each field is described below:
Item
Description
OfficeServ Link
Enter the IP address of OfficeServ Link and the port number for
Connection
connection.
If you are not aware of the port number, contact the OfficeServ Link
manager and enter a valid value.
Data Manager
Specify a port to be connected to Data Manager. If another
Listen Port
application already uses Port Number. 5001 on a computer where
OfficeServ DataView is installed, the default value, 5001, should be
changed to another value.
Log Information
Save an operation log of Data Collector in this field.
If an error occurs while using Data Collector, this field will allow you
to trace the error.
Level of detail in log information depends on log levels. There are
three log levels of None to Detail.
Set Log File Size to 1 MB to 100 MB and Log File Count to 1 to 20.
Set [Log Print] to Simple or Detail in order to display log information
through Debug View.
Data Collector
Set Startup Mode to Automatic. Then, even if you do not click the
Option
[Run] button of Data Collector, Data Collector will start.
If Startup Mode is set to Manual, click the [Run] button to start
operation.
No values other than those of [Log Level] and [Log Print] can be changed in a
running Data Collector.
© SAMSUNG Electronics Co., Ltd.
25
Ошибка! Стиль не определен.
Data Manager
Data Manager creates a cumulative record for 15 minutes from the call log
created by Data Collector. This record will be displayed in each field of a
statistical report.
Data Manager saves the log record received from Data Collector and the
created cumulative record in the database.
Data Manager Menu
Data Manager does not have a window for user interfaces. You can monitor
the operation of Data Manager by using Scheduler. If the icon is displayed in
the system tray, click the right button of mouse on the icon of the system
tray to use the menus of Data Manager.
Log Records
[Log Records] allows you to select a type of the call log to be saved in the
database. If all types of logs are saved in the database, log records will
increase and bottleneck may occur while the database is operating. To prevent
OfficeServ DataView from being degraded due to bottlebeck, limit number of
logs to be saved.
Select [Log Records]. Then, the dialog box below will appear:
Select the checkbox of a log to be saved and click [OK].
26
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Operation Logs
[Operation Logs] allows you to perform settings for saving operation logs of
Data Manager.
Select [Operation Logs]. The dialog box below will appear:
Each field is described below:
Field
Level
Description
Sets the detail level of a log to be saved.
There are five levels of None to Full.
Size
Sets the size of an operation log to 1 MB to 100 MB.
Count
Sets the number of operation logs to 1 to 100.
© SAMSUNG Electronics Co., Ltd.
27
Ошибка! Стиль не определен.
Starting OfficeServ DataView
Follow the steps below to start OfficeServ DataView:
1.
Double-click the [OfficeServ DataView Scheduler Hot Key] icon from
the desktop or select [Start] Æ [Programs(P)] Æ [OfficeServ DataView]
Æ [Scheduler]. Then, the initialization window below will appear:
2. Once Scheduler runs, the window below will appear:
28
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Once Scheduler starts, the Scheduler icon is displayed in the system tray.
If a server module of OfficeServ DataView does not start, a icon( )(pink)
will be displayed.
3.
Click [Start All] to start all server modules. Or, click each [Start] button
to start each module one by one.
Starting Each Module
Data Collector downloads configuration data from the OfficeServ system
when the module starts. It is recommended that Data Manager should start
after Data Collector starts. Data Manager does not operate until Data
Collector starts properly.
4.
Once each module starts properly, the Status icon, [Stop All], and all of
the [Stop] buttons are enabled while [Start All] and all of the [Start]
buttons are disabled.
Once all of the server modules operate properly, the icon displayed in the
system tray is changed to the normal operation icon( )(light green).
If all of the server modules operate properly, open the home page of
OfficeServ DataView to view data on monitoring, and statistics.
© SAMSUNG Electronics Co., Ltd.
29
Ошибка! Стиль не определен.
Main Window
Run Internet Explorer and enter the following in the address bar to view the
home page of OfficeServ DataView. Then, press [Enter].
Enter the IP address of the PC where OfficeServ DataView is installed or the
NetBIOS(Network Basic Input Output System) name instead of ‘127.0.0.1’.
Enter the web address of OfficeServ DataView correctly and press [Enter].
Then, the home page of OfficeServ DataView that can be logged in will
appear as shown in the figure below:
30
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
If you use OfficeServ DataView for the first time, enter the administrator ID
provided by default and password. Enter ‘admin’ in ID and ‘samsung’ in
PWD.
If login is successful, select one of the menus at the left of the window to
perform a function of OfficeServ DataView.
© SAMSUNG Electronics Co., Ltd.
31
Ошибка! Стиль не определен.
Menus
The main menus of the OfficeServ DataView home page are shown in the
figure below:
Locate the mouse pointer on each main menu. Then, the sub-menus will appear.
For detailed information on monitoring, and statistics, see Chapter 4 to
Chapter 5 of this document.
Each sub-menu of [Configuration] is described in next section,
‘Configuration’.
32
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Configuration
The Configuration menu of OfficeServ DataView has the submenus of User,
System Info, Scheduled Report, and Personalize.
User
This menu allows you to retrieve the user list of OfficeServ DataView, and to
add or delete a user. Also, you can modify user information or searches a
specific user by using this menu.
If the selected list has multiple pages, click [<First], [<Prev], [Next>], or
[Last>] to move from a page to another.
User List
Select [User List]. Then, list of the registered OfficeServ DataView users will
appear as shown in the figure below:
Add User Account
Select [Add User Account]. Then, the window that allows you to add a user to
the user list will appear as shown in the figure below:
© SAMSUNG Electronics Co., Ltd.
33
Ошибка! Стиль не определен.
Each field is described below:
Item
User Name
Description
Enter a user name. You can enter up to 25 Korean characters or up
to 50 alphabetic characters.
Login ID
Enter a login ID. You can enter up to 20 alphabetic characters or
numbers. The characters are case-sensitive.
Login Password
Enter a login password. You can enter up to 20 alphabetic characters
or numbers. The characters are case-sensitive.
Tel NO
Enter the telephone number of a user. You can enter up to 20
numbers. This field is optional.
E-Mail
Enter the e-mail address of a user. You can enter up to 50 characters.
This field is optional.
User Level
Select a user level. The administrator can use all of the functions
supported by OfficeServ DataView. Regular users cannot use the
[User], [System Info], and [Scheduled Report] submenus of the
[Configuration] menu.
Delete User Account
Select [Delete User Account]. Then, the window that allows you to delete a
user from the user list will appear as shown in the figure below:
Select the checkbox of a user to be deleted and click [Delete] to delete the
account of the selected user. You cannot delete the account of ‘Administrator’,
which is the default user.
34
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Modify User Account
Select [Modify User Account]. The window that allows you to modify user
profiles will appear as shown in the figure below:
Modify the fields you want and select checkboxes to take effect changes.
Then, click [Change].
If you modify user information and do not click [Change], the window will
not be updated.
System Info
This menu allows you to verify the OfficeServ system information and the
OfficeServ DataView operating environment.
You can select the items you wish to display from the Wallboard.
OfficeServ System Information
This menu allows you to verify information on the connection between the
OfficeServ system and Officeserv DataView.
© SAMSUNG Electronics Co., Ltd.
35
Ошибка! Стиль не определен.
Items in the above figure are described below:
Item
Description
System Name
Name of the OfficeServ system
System Version
Version of the OfficeServ system main program
System Date
Date of the OfficeServ system main program
System Country
Country information set in the OfficeServ system
OfficeServ Link IP
IP address of the OfficeServ Link
Address
OfficeServ Link
Number of the port used by the Data Collector for connecting to
Port
the OfficeServ Link
Host Name
IP address of the computer where the OfficeServ DataView is
installed, or the NetBIOS name
Collector Port
Number of the port used by the Data Manager for connecting to
the Data Collector
36
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Database Information
This menu is used for displaying information on the DB(Database) used by
OfficeServ DataView. The DB information used by the current web program
and a list of backed up DBs are displayed.
In order to view a statistics report on a backed up DB, select a DB and click
[Register].
Connecting to a changed DB is valid only during the current session. If you
log out and log in again, you will be connected to the default DB without
affecting other users.
Trunk Group Information
This menu is used for displaying information on trunk groups configured in
the OfficeServ system.
© SAMSUNG Electronics Co., Ltd.
37
Ошибка! Стиль не определен.
Station/UCD Group Information
This menu is used for displaying information on station groups configured in
the OfficeServ system.
38
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Scheduled Report
This menu allows you to setup scheduled reports or delete unnecessary
scheduled reports.
Scheduled Report Setup
This menu is used for setting the period and items for the report.
Different options are provided for setting the period of a scheduled report
depending on whether the report is a daily report, a weekly report, or a
monthly report.
Set Daily Report
Item
Description
Use
Check this option to use a daily report.
Day Time
Set the time period for which the report should be created.
© SAMSUNG Electronics Co., Ltd.
39
Ошибка! Стиль не определен.
Set Weekly Report
Item
Description
Use
Check this option to use a weekly report.
Start Day of Week
Specify the start day of the weekly report. The report will be
generated between 00:00 and 01:00 0n the next start day.
Set Monthly Report
Item
40
Description
Use
Check this option to use a monthly report.
Start Day of
Specify the start day of the monthly report. The report will be
Month
generated between 00:00 and 01:00 0n the next start day.
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Scheduled Report Item Setup
You can create scheduled reports for trunks and UCD groups.
Check the Detail checkbox to view detailed statistics for each time zone.
© SAMSUNG Electronics Co., Ltd.
41
Ошибка! Стиль не определен.
Personalize
You can personalize the user environment such as skin and language.
Skin refers to graphic or audio files used for changing the shape of a game
character or a UI(User Interface) to one that is preferred by the user.
Set Skin
Select [Personalize] Æ [Set Skin] and display the following window:
Select a skin and click [Register].
Select Language
Select [Personalize] Æ [Select Language] and display the following window:
Select your language from the combo box and click [Register].
Set Wallboard
Select [Personalize] Æ [Set Wallboard] and display the following window:
Mark the values you want to monitor in the Wallboard, put the threshold value
to alarm and click [Save].
42
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
© SAMSUNG Electronics Co., Ltd.
43
OfficeServ DataView User Guide
CHAPTER 4. Statistics
This chapter describes the statistics function of the OfficeServ DataView Web page.
Statistics Window Layout
You can use the statistics function after connecting and logging in to the
OfficeServ DataView homepage.
The general layout of a statistics window is shown below:
Page Title
Sum
© SAMSUNG Electronics Co., Ltd.
Execution Options
Additional Menus
Detailed Results
45
Ошибка! Стиль не определен.
Page Title
The selected submenu is displayed as the title.
Additional Menus
The two menus below are provided as additional menus. Refer to the
‘Additional Menu’ section of this chapter for detailed descriptions.
Menu
Description
Print the report.
Export the report into the Microsoft Excel.
Execution Options
This section of the window allows you to set a statistics option and to start or
stop the statistics process. The [From~To] option is applied to all statistics
pages, and additional options may be provided depending on the statistics item.
Refer to the ‘Execution Option Setup’ section of this chapter.
Sum
This section of the window displays the sum of each statistical item.
Detailed Results
This section of the window displays detailed statistics results for the selected
submenu.
46
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Selecting a Statistics Item
Statistics windows display data generated by the OfficeServ system and saved
in the DB, based on various criteria such as trunk and station. You can select a
statistics item by placing the mouse pointer over a main menu and clicking a
submenu from the list displayed.
© SAMSUNG Electronics Co., Ltd.
47
Ошибка! Стиль не определен.
Statistics Item
Statistics items are categorized into six main menus, Trunk, Station, UCD,
Operator, Miscellaneous and Scheduled Report, and are further categorized
into fifty one submenus.
48
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Additional Menus
Print
Click the Print(
) icon from the additional menus to print a statistics
window. The following figure shows an example of clicking the Print icon of a
Trunk Overall Statistics window:
A page for printing is created with the title on the upper middle section, the
data retrieval period on the upper left section, and the printing date on the
upper right section of the page. The sum and detailed results are expressed in
black and white colors.
The <Print> window appears over the new page. Click the [Print] to start
printing.
© SAMSUNG Electronics Co., Ltd.
49
Ошибка! Стиль не определен.
Export to Excel
Click the Export to Excel (
) icon from the additional menus to export a
report into Microsoft Excel. Note that it works only when you have the
Microsoft Excel properly installed on your PC.
If the report opens with the Internet Explorer, you need to modify the file
option.
Open the Windows Explorer and select [Tools] -> [Folder Option].
The select the [File Types] tab, select [XLS] from the [Registered file types]
list, and click the [Advanced] button
When the [Edit File Type] dialog open, clear this option.
- Browse in same window
50
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Whenever you export a report into Excel, you will see the download warning.
If you don’t want to see the file download warning anymore, clear this option.
- Confirm open after download
© SAMSUNG Electronics Co., Ltd.
51
Ошибка! Стиль не определен.
Execution Option Setup
The [From ~ To] option is used for setting the scope of data to be retrieved,
and the [Each] option is used for setting the data to be displayed on each row
of the Each Time table. Additional options may be provided depending on the
statistics item.
The procedure for setting the execution options is as follows:
1.
2.
3.
4.
5.
Start Date: Click the DD/MM/YY combo box(
) next to
the [From] option to display a calendar window shown below, and select
the start date from the window.
Start Time: Click the DD/MM/YY combo box(
) next to
the [From] option and select the time(0~23 hour, 00~45 minute).
End Date: Click the DD/MM/YY combo box next to the [To] option and
select the end date.
End Time: Click the DD/MM/YY combo box next to the [To] option and
select the time(0~23 hour, 00~45 minute).
Detailed Results: Select 15min, 30min, 1hour, day, week, or month from
the [Each] option to display the selected value as a row of the Each Time
table.
Trunk Statistics
This section describes the statistics on trunks of the OfficeServ system.
52
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Trunk Overall Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on trunk calls. Select the Trunk Overall Statistics submenu of the
Trunk menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
Total Line
Total number of lines
Fault Line
Number of faulty lines
Use Line
Number of available lines
Max Use Line
Maximum number of lines used
Seize Try Cnt
Number of seizure attempts
Seize Succ Cnt
Number of successful seizures
Fail Cnt
Number of failures
Call Cnt
Number of successful calls
Retrieved Cnt
Number of calls retrieved by different subscriber from the one
who held the call
Seize Time
Seizure duration
Call Time
Call duration
Avg Seize Time
Average seizure duration(Seizure duration/Number of successful
seizures)
© SAMSUNG Electronics Co., Ltd.
53
Ошибка! Стиль не определен.
Column
Description
Avg Call Time
Average call duration(Call duration/Number of successful calls)
Seize Succ Ratio
Seizure success ratio(Number of successful seizures/Number of
seizure attempts * 100)
Call Ratio
Call success ratio(Number of successful calls/Number of seizure
attempts * 100)
Traffic(Erlang)
54
Traffic(Seizure duration/Elapsed time)
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Trunk Incoming Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on trunk inbound calls. Select the Trunk Inbound Statistics submenu
of the Trunk menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
Total Line
Total number of lines
Fault Line
Number of faulty lines
Use Line
Number of available lines
Max Use Line
Maximum number of lines used
In Seize Try Cnt
Number of seizure attempts of inbound calls
In Seize Succ Cnt
Number of successful seizures of inbound calls
In Fail Cnt
Number of inbound calls failed
In Call Cnt
Number of successful inbound calls
In Seize Time
Seizure duration of inbound calls
In Call Time
Inbound call duration
© SAMSUNG Electronics Co., Ltd.
55
Ошибка! Стиль не определен.
Avg In Seize Time
Average seizure duration of inbound calls(Seizure duration of
inbound calls/Number of successful seizures of inbound calls)
Avg In Call Time
Average inbound call duration(Inbound call duration/Number of
successful inbound calls)
In Seize Succ
Seizure success ratio of inbound calls
Ratio
(Number of successful seizures of inbound calls/Number of
seizure attempts of inbound calls * 100)
In Call Ratio
Inbound call success ratio
(Number of successful inbound calls/Number of seizure attempts
of inbound calls * 100)
In Traffic(Erlang)
56
Inbound call traffic(Seizure duration of inbound calls/Elapsed time)
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Trunk Outgoing Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on trunk outbound calls. Select the Trunk Outbound Statistics
submenu of the Trunk menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
Total Line
Total number of lines
Fault Line
Number of faulty lines
Use Line
Number of available lines
Max Use Line
Maximum number of lines used
Out Seize Try Cnt
Number of seizure attempts of outbound calls
Out Seize Succ Cnt
Number of successful seizures of outbound calls
Out Fail Cnt
Number of outbound calls failed
Out Call Cnt
Number of successful outbound calls
Out Seize Time
Seizure duration of outbound calls
Out Call Time
Outbound call duration
© SAMSUNG Electronics Co., Ltd.
57
Ошибка! Стиль не определен.
Avg Out Seize Time
Average seizure duration of outbound calls(Seizure duration of
outbound calls/Number of successful seizures of outbound
calls)
Avg Out Call Time
Average outbound call duration(Outbound call duration/Number
of successful outbound calls)
Out Seize Succ
Seizure success ratio of outbound calls(Number of successful
Ratio
seizures of outbound calls/Number of seizure attempts of
outbound calls * 100)
Out Call Ratio
Outbound call success ratio
(Number of successful outbound calls/Number of seizure
attempts of outbound calls * 100)
Out Traffic(Erlang)
Outbound call traffic(Seizure duration of outbound calls/Elapsed
time)
58
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Trunk Distribution Statistics
This menu allows you to verify the statistics on the distribution of trunk calls
based on call duration and time zone. Select the Trunk Distribution Statistics
submenu of the Trunk menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
≤ 30 s
Number of calls whose duration is less than or equal to 30
seconds
≤ 60 s
Number of calls whose duration is less than or equal to 60
seconds
≤ 90 s
Number of calls whose duration is less than or equal to 90
seconds
≤2m
Number of calls whose duration is less than or equal to 2 minutes
≤3m
Number of calls whose duration is less than or equal to 3 minutes
≤4m
Number of calls whose duration is less than or equal to 4 minutes
≤5m
Number of calls whose duration is less than or equal to 5 minutes
≤ 10 m
Number of calls whose duration is less than or equal to 10
minutes
© SAMSUNG Electronics Co., Ltd.
59
Ошибка! Стиль не определен.
≤ 20 m
Number of calls whose duration is less than or equal to 20
minutes
≤ 30 m
Number of calls whose duration is less than or equal to 30
minutes
60
> 30 m
Number of calls whose duration is greater than 30 minutes
Total Cnt
Total number of calls
Max Call Time
Maximum call duration
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Trunk Incoming Distribution Statistics
This menu allows you to verify the statistics on the distribution of trunk
inbound calls based on call duration and time zone. Select the Trunk Inbound
Distribution Statistics submenu of the Trunk menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
≤ 30 s
Number of inbound calls whose duration is less than or equal to
30 seconds
≤ 60 s
Number of inbound calls whose duration is less than or equal to
60 seconds
≤ 90 s
Number of inbound calls whose duration is less than or equal to
90 seconds
≤2m
Number of inbound calls whose duration is less than or equal to 2
minutes
≤3m
Number of inbound calls whose duration is less than or equal to 3
minutes
≤4m
Number of inbound calls whose duration is less than or equal to 4
minutes
© SAMSUNG Electronics Co., Ltd.
61
Ошибка! Стиль не определен.
≤5m
Number of inbound calls whose duration is less than or equal to 5
minutes
≤ 10 m
Number of inbound calls whose duration is less than or equal to
10 minutes
≤ 20 m
Number of inbound calls whose duration is less than or equal to
20 minutes
≤ 30 m
Number of inbound calls whose duration is less than or equal to
30 minutes
> 30 m
Number of inbound calls whose duration is greater than 30
minutes
62
Total Cnt
Total number of inbound calls
Max Call Time
Maximum inbound call duration
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Trunk Outgoing Distribution Statistics
This menu allows you to verify the statistics on the distribution of trunk
outbound calls based on call duration and time zone. Select the Trunk
Outbound Distribution Statistics submenu of the Trunk menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
≤ 30 s
Number of outbound calls whose duration is less than or equal to
30 seconds
≤ 60 s
Number of outbound calls whose duration is less than or equal to
60 seconds
≤ 90 s
Number of outbound calls whose duration is less than or equal to
90 seconds
≤2m
Number of outbound calls whose duration is less than or equal to
2 minutes
≤3m
Number of outbound calls whose duration is less than or equal to
3 minutes
≤4m
Number of outbound calls whose duration is less than or equal to
4 minutes
© SAMSUNG Electronics Co., Ltd.
63
Ошибка! Стиль не определен.
≤5m
Number of outbound calls whose duration is less than or equal to
5 minutes
≤ 10 m
Number of outbound calls whose duration is less than or equal to
10 minutes
≤ 20 m
Number of outbound calls whose duration is less than or equal to
20 minutes
≤ 30 m
Number of outbound calls whose duration is less than or equal to
30 minutes
> 30 m
Number of outbound calls whose duration is greater than 30
minutes
64
Total Cnt
Total number of outbound calls
Max Call Time
Maximum outbound call duration
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Trunk Incoming Fail Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on failed trunk inbound calls. Select the Trunk Inbound Fail Statistics
submenu of the Trunk menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
In Seize Try Cnt
Number of seizure attempts of inbound calls
In Fail Cnt
Number of failed inbound calls
In Fail Ratio
Inbound failure ratio(Number of failed inbound calls/Number of
seizure attempts of inbound calls * 100)
Tel Not Exist
Inexistent phone number
Limited Class
Limited class
TRK Busy
Trunk is busy.
STN Busy
Station is busy.
STN DND
Station DND(Do Not Disturb)
STN No More
No more stations
Plug Out
Unplugged
Device Mismatch
Device is invalid.
© SAMSUNG Electronics Co., Ltd.
65
Ошибка! Стиль не определен.
66
Group Busy
Group is busy
Unknown
Unknown
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Trunk Outgoing Fail Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on failed trunk outbound calls. Select the Trunk Outbound Fail
Statistics submenu of the Trunk menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
Out Seize Try Cnt
Number of seizure attempts of outbound calls
Out Fail Cnt
Number of failed outbound calls
Out Fail Ratio
Outbound failure ratio(Number of failed outbound calls/Number
of seizure attempts of outbound calls * 100)
All Busy
All lines are busy
Unknown
Unknown
© SAMSUNG Electronics Co., Ltd.
67
Ошибка! Стиль не определен.
Trunk Outgoing Statistics by Group
This menu allows you to verify the overall statistics and the group-based
statistics on trunk outbound calls. Select the Trunk Outbound Statistics by
Group submenu of the Trunk menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
68
Description
Group Cnt
Total number of groups
Group NO
Group Number
Total Line
Total number of lines
Fault Line
Number of faulty lines
Use Line
Number of available lines
Max Use Line
Maximum number of lines used
Out Seize Try Cnt
Number of seizure attempts of outbound calls
Out Seize Succ Cnt
Number of successful seizures of outbound calls
Out Fail Cnt
Number of failures of outbound calls
Out Call Cnt
Number of successful outbound calls
Out Seize Time
Seizure duration of outbound calls
Out Call Time
Outbound call duration
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Avg Out Seize Time
Average seizure duration of outbound calls(Seizure duration of
outbound calls/Number of successful seizures of outbound calls)
Avg Out Call Time
Average outbound call duration(Outbound call duration/Number
of successful outbound calls)
Out Seize Succ
Seizure success ratio of outbound calls
Ratio
(Number of successful seizures of outbound calls/Number of
seizure attempts of outbound calls * 100)
Out Call Ratio
Outbound call success ratio(Number of successful outbound
calls/Number of seizure attempts of outbound calls * 100)
Out Traffic(Erlang)
Outbound call traffic(Seizure duration of outbound calls/Elapsed
time)
© SAMSUNG Electronics Co., Ltd.
69
Ошибка! Стиль не определен.
Trunk Group Outgoing Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on outbound calls of a specific trunk group. Select the Trunk Group
Outbound Statistics submenu of the Trunk menu.
Select the target time period and trunk group from the execution options and
click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Group NO
Group Number
Time
Time(The first and last rows indicate detailed time.)
Total Line
Total number of lines
Fault Line
Number of faulty lines
Use Line
Number of available lines
Max Use Line
Maximum number of lines used
Out Seize Try Cnt
Number of seizure attempts of outbound calls
Out Seize Succ Cnt
Number of successful seizures of outbound calls
Out Fail Cnt
Number of failures of outbound calls
Out Call Cnt
Number of successful outbound calls
Out Seize Time
Seizure duration of outbound calls
Out Call Time
Outbound call duration
Avg Out Seize Time
Average seizure duration of outbound calls(Seizure duration of
outbound calls/Number of successful seizures of outbound calls)
70
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Avg Out Call Time
Average outbound call duration(Outbound call duration/Number
of successful outbound calls)
Out Seize Succ
Seizure success ratio of outbound calls
Ratio
(Number of successful seizures of outbound calls/Number of
seizure attempts of outbound calls * 100)
Out Call Ratio
Outbound call success ratio(Number of successful outbound
calls/Number of seizure attempts of outbound calls * 100)
Out Traffic(Erlang)
Outbound call traffic(Seizure duration of outbound calls/Elapsed
time)
© SAMSUNG Electronics Co., Ltd.
71
Ошибка! Стиль не определен.
Trunk Port Statistics
This menu allows you to verify the overall statistics on and calling list of a
specific trunk port. Select the Trunk Port Statistics submenu of the Trunk
menu.
Select the target time period, type and port from the execution options and
click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Trunk Tel NO
Trunk phone number
Total Calls
Number of seizures
Fail Cnt
Number of failures
Abandoned Calls
Number of calls hung up while ringing
Completed Calls
Number of successful calls
Call Ratio
Call success ratio(Number of successful calls/Number of
seizures * 100)
72
Type
Inbound/Outbound
External NO
External Number
In/Out Tel NO
Phone number
DID NO
DID(Direct Inward Dialing) Number
Seize Begin Time
Seizure start time
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Seize End Time
Seizure end time
Seize Time
Seizure duration
Call Time
Call duration
Call Type
Call type(Primary/Recall/Callback/Overflow/Consultation/Transfer
/Conference/Pickup/Unknown)
End Status
End status(Fail/Hook Off/Ring/Connected/Queuing/External
Outbound/External Answer/Hold)
End Cause
© SAMSUNG Electronics Co., Ltd.
Cause of end
73
Ошибка! Стиль не определен.
Trunk Abandoned Call List
This menu allows you to verify the list of trunk abandoned calls. Select the
Trunk Abandoned Call List submenu of the Trunk menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
74
Description
Abandoned Call Cnt
Total number of abandoned calls
NO
Record number
Begin Time
Start time
Trunk Tel NO
Trunk phone number
In Tel NO
Inbound phone number
DID NO
DID number
CID NO
CID(Caller Identification) number
Abd Wait Time
Waiting time of abandoned calls
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Station Statistics
This section describes the statistics on stations of the OfficeServ system.
Station Overall Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on station calls. Select the Station Overall Statistics submenu of the
Station menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
Total Line
Total number of lines
Fault Line
Number of faulty lines
Use Line
Number of available lines
Max Use Line
Maximum number of lines used
In/Out Try Cnt
Number of inbound/outbound attempts
In/Out Succ Cnt
Number of successful inbound/outbound calls
Fail Cnt
Number of failures
Call Cnt
Number of successful calls
Pickup Cnt
Number of calls picked up
Retrieved Cnt
Number of calls retrieved by different subscriber from the one
© SAMSUNG Electronics Co., Ltd.
75
Ошибка! Стиль не определен.
Column
Description
who held the call
Seize Time
Seizure duration
Call Time
Call duration
Avg Seize Time
Average seizure duration(Seizure duration/Number of successful
seizures)
Avg Call Time
Average call duration(Call duration/Number of successful calls)
In/Out Succ Ratio
Inbound/Outbound success ratio(Number of successful inbound
/outbound calls/Number of attempts of inbound/outbound calls * 100)
Call Ratio
Call success ratio(Number of successful calls/Number of seizure
attempts * 100)
76
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Station Incoming Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on station inbound calls. Select the Station Inbound Statistics
submenu of the Station menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
Total Line
Total number of lines
Fault Line
Number of faulty lines
Use Line
Number of available lines
In Req Cnt
Number of inbound requests
In Succ Cnt
Number of successful inbound calls
In Fail Cnt
Number of inbound calls failed
In Answer Cnt
Number of answered inbound calls
In No Answer Cnt
Number of unanswered inbound calls
In Xfer Cnt
Number of inbound transfers
In Seize Time
Number of seizure duration of inbound calls
In Call Time
Inbound call duration
Avg In Seize Time
Average seizure duration of inbound calls(Seizure duration of
inbound calls/Number of successful seizure of inbound calls)
© SAMSUNG Electronics Co., Ltd.
77
Ошибка! Стиль не определен.
Avg In Call Time
Average inbound call duration(Inbound call duration/Number of
successful inbound calls)
In Succ Ratio
Inbound success ratio(Number of successful inbound
calls/Number of inbound requests * 100)
In Answer Ratio
Inbound answer ratio(Number of answered inbound calls/Number
of successful inbound calls * 100)
78
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Station Outgoing Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on station outbound calls. Select the Station Outbound Statistics
submenu of the Station menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
Total Line
Total number of lines
Fault Line
Number of faulty lines
Use Line
Number of available lines
Out Try Cnt
Number of attempts of outbound calls
Out Fail Cnt
Number of outbound calls failed
Out Succ Cnt
Number of successful outbound calls
Hook Off Cnt
Number of hook-off cases
Out Call Cnt
Number of outbound calls
Out Xfer Cnt
Number of outbound transfers
Out Seize Time
Number of seizure duration of outbound calls
Out Call Time
Outbound call duration
© SAMSUNG Electronics Co., Ltd.
79
Ошибка! Стиль не определен.
Avg Out Seize Time
Average seizure duration of outbound calls(Seizure duration of
outbound calls/Number of successful seizure of outbound calls)
Avg Out Call Time
Average outbound call duration(Outbound call duration/Number
of successful outbound calls)
Out Succ Ratio
Outbound success ratio(Number of successful outbound
calls/Number of outbound requests * 100)
Out Call Ratio
Outbound call ratio(Number of outbound calls/Number of
attempts of outbound calls * 100)
80
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Station Incoming Detailed Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on station inbound calls in detail. Select the Station Inbound Detailed
Statistics submenu of the Station menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
Internal Inbound
Internal inbound
External Inbound
External inbound
In Req Cnt
Number of inbound requests
In Succ Cnt
Number of successful inbound calls
Ans Cnt
Number of calls answered
Xfer Cnt
Number of transfers
Seize Time
Seizure duration
Call Time
Call duration
Avg Call Time
Average call duration(Call duration/Number of calls answered)
In Succ Ratio
Inbound success ratio(Number of successful inbound
calls/Number of inbound requests * 100)
Ans Ratio
Answer ratio(Number of calls answered/Number of successful
inbound calls * 100)
© SAMSUNG Electronics Co., Ltd.
81
Ошибка! Стиль не определен.
Station Outgoing Detailed Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on station outbound calls in detail. Select the Station Outbound
Detailed Statistics submenu of the Station menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
Internal Outbound
Internal Outbound
External Outbound
External outbound
Out Try Cnt
Number of outbound attempts
Out Succ Cnt
Number of successful outbound calls
Xfer Cnt
Number of transfers
Seize Time
Seizure duration
Call Time
Call duration
Avg Seize Time
Average seizure duration(Seizure duration/Number of successful
outbound calls)
Avg Call Time
Average call duration(Call duration/Number of successful
outbound calls)
Out Succ Ratio
Outbound success ratio(Number of successful outbound
calls/Number of outbound requests * 100)
Call Ratio
Call ratio
(Number of calls/Number of successful outbound calls * 100)
82
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Station Outgoing Fail Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on failed station outbound calls. Select the Station Outbound Fail
Statistics submenu of the Station menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
Out Try Cnt
Number of outbound attempts
Out Fail Cnt
Number of outbound failures
Out Fail Ratio
Outbound failure ratio(Number of outbound failures/Number of
outbound attempts * 100)
Tel Not Exist
Inexistent phone number
Limited Class
Limited class
TRK Busy
Trunk is busy.
STN Busy
Station is busy.
STN DND
Station DND
STN No More
No more stations
Plug Out
Unplugged
Device Mismatch
Device is invalid.
Group Busy
Group is busy.
© SAMSUNG Electronics Co., Ltd.
83
Ошибка! Стиль не определен.
Unknown
84
Unknown
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Station Tried Features Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on station features. Select the Tried Features Statistics submenu of
the Station menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
Call Back
Call back
Camp On
Camp on
DND
Do Not Disturb
Forward
Forwarding
Message
Leaving messages
OHVA
Urgent alarm
Programmed Message
Programming messages
© SAMSUNG Electronics Co., Ltd.
85
Ошибка! Стиль не определен.
Station Incoming Statistics by Group
This menu allows you to verify the overall statistics and the group-based
statistics on station inbound calls. Select the Station Inbound Statistics by
Group submenu of the Station menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
86
Description
Group Cnt
Total number of groups
Group NO
Group number
Group Name
Name of a station group. Blank if not available
Total Line
Total number of lines
Fault Line
Number of faulty lines
Use Line
Number of available lines
In Req Cnt
Number of inbound requests
In Succ Cnt
Number of successful inbound calls
All Busy Fail Cnt
Number of failures when all lines are busy
ETC Fail Cnt
Number of other failures
In Answer Cnt
Number of answered inbound calls
In No Answer Cnt
Number of unanswered inbound calls
In Xfer Cnt
Number of inbound transfers
In Seize Time
Number of seizure duration of inbound calls
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
In Call Time
Inbound call duration
Avg In Seize Time
Average seizure duration of inbound calls(Seizure duration of
inbound calls/Number of successful seizures of inbound calls)
Avg In Call Time
Average inbound call duration(Inbound call duration/Number of
successful inbound calls)
In Succ Ratio
Inbound success ratio
(Number of successful inbound calls/Number of inbound
requests * 100)
In Answer Ratio
Inbound answer ratio
(Number of answered inbound calls/Number of successful
inbound calls * 100)
© SAMSUNG Electronics Co., Ltd.
87
Ошибка! Стиль не определен.
Station Group Incoming Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on inbound calls of a specific station group. Select the Station Group
Inbound Statistics submenu of the Station menu.
Select the target time period and station group from the execution options and
click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
88
Description
Group NO
Group number
Group Name
Name of a station group. Blank if not available
Time
Time(The first and last rows indicate detailed time.)
Total Line
Total number of lines
Fault Line
Number of faulty lines
Use Line
Number of available lines
In Req Cnt
Number of inbound requests
In Succ Cnt
Number of successful inbound calls
All Busy Fail Cnt
Number of failures when all lines are busy
ETC Fail Cnt
Number of other failures
In Answer Cnt
Number of answered inbound calls
In No Answer Cnt
Number of unanswered inbound calls
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
In Xfer Cnt
Number of inbound transfers
In Seize Time
Number of seizure duration of inbound calls
In Call Time
Inbound call duration
Avg In Seize Time
Average seizure duration of inbound calls(Seizure duration of
inbound calls/Number of successful seizures of inbound calls)
Avg In Call Time
Average inbound call duration(Inbound call duration/Number of
successful inbound calls)
In Succ Ratio
Inbound success ratio(Number of successful inbound calls/
Number of inbound requests * 100)
In Answer Ratio
Inbound answer ratio(Number of answered inbound calls/
Number of successful inbound calls * 100)
© SAMSUNG Electronics Co., Ltd.
89
Ошибка! Стиль не определен.
Station Group Inbound Detailed Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on inbound calls of a specific station group in detail. Select the
Station Group Inbound Detailed Statistics submenu of the Station menu.
Select the target time period and station group from the execution options and
click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
90
Description
Group NO
Group number
Group Name
Name of a station group. Blank if not available
Time
Time(The first and last rows indicate detailed time.)
Internal Inbound
Internal inbound
External Inbound
External inbound
In Req Cnt
Number of inbound requests
In Succ Cnt
Number of successful inbound calls
Ans Cnt
Number of calls answered
Xfer Cnt
Number of transfers
Seize Time
Seizure duration
Call Time
Call duration
Avg Call Time
Average call duration(Call duration/Number of calls answered)
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
In Succ Ratio
Inbound success ratio
(Number of successful inbound calls/Number of inbound
requests * 100)
Ans Ratio
Answer ratio(Number of calls answered/Number of successful
inbound calls * 100)
© SAMSUNG Electronics Co., Ltd.
91
Ошибка! Стиль не определен.
Station Port Statistics
This menu allows you to verify the overall statistics on and calling list of a
specific station port. Select the Station Port Statistics submenu of the Station
menu.
Select the target time period, type and port from the execution options and
click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Station Tel NO
Station phone number
Total Calls
Number of seizures
Fail Cnt
Number of failures
Abandoned Calls
Number of calls hung up while ringing
Completed Calls
Number of successful calls
Call Ratio
Call success ratio(Number of successful calls/Number of
seizures * 100)
92
Type
Inbound/Outbound
External NO
External number
In/Out Tel NO
Phone number
Seize Begin Time
Seizure start time
Call Begin Time
Call start time
Seize End Time
Seizure end time
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Seize Time
Seizure duration
Call Time
Call duration
Call Type
Call type(Primary/Recall/Callback/Overflow/Consultation/Transfer
/Conference/Unknown)
End Status
End status(Fail/Hook Off/Ring/Connected/Queuing/External
Outbound/External Answer)
End Cause
© SAMSUNG Electronics Co., Ltd.
Cause of end
93
Ошибка! Стиль не определен.
UCD Statistics
This section describes the statistics on UCD of the OfficeServ system.
UCD Overall Incoming Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on UCD inbound calls. Select the UCD Overall Inbound Statistics
submenu of the UCD menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
94
Description
Group Cnt
Number of groups
Time
Time(The first and last rows indicate detailed time.)
Agent Cnt
Number of agents
Login Agent Cnt
Number of agents logged in
In Cnt
Number of inbound calls
Ans Cnt
Number of calls answered
Abd Call Cnt
Number of abandoned calls
Overflow In Cnt
Number of overflow inbound calls
Overflow Out Cnt
Number of overflow outbound calls
Force Log Out Cnt
Number of forced logout cases
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Column
Description
Xfer In Ans Cnt
Number of transferred inbound calls answered
Call Time
Call duration
© SAMSUNG Electronics Co., Ltd.
95
Ошибка! Стиль не определен.
Column
Avg Call Time
Description
Average call duration(Call duration/(Number of calls answered +
Number of transferred inbound calls answered ))
Avg Wait Time
Average waiting duration(Waiting duration of connected calls/
Number of calls answered)
Avg Abd Time
Average waiting duration of abandoned calls(Waiting duration of
abandoned calls/Number of abandoned calls)
Ans Ratio
Answer ratio(Number of calls answered/Number of inbound calls
* 100)
96
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
UCD Incoming Statistics by Group
This menu allows you to verify the overall statistics and the group-based
statistics on UCD inbound calls. Select the UCD Inbound Statistics by Group
submenu of the UCD menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Group Cnt
Number of groups
Group NO
Group number
Group Name
Name of a station group. Blank if not available
Agent Cnt
Number of agents
Login Agent Cnt
Number of agents logged in
In Cnt
Number of inbound calls
Ans Cnt
Number of calls answered
Abd Call Cnt
Number of abandoned calls
Overflow In Cnt
Number of overflow inbound calls
Overflow Out Cnt
Number of overflow outbound calls
Force Log Out Cnt
Number of forced logout cases
Xfer In Ans Cnt
Number of transferred inbound calls answered
Call Time
Call duration
© SAMSUNG Electronics Co., Ltd.
97
Ошибка! Стиль не определен.
Column
Avg Call Time
Description
Average call duration(Call duration/(Number of calls answered +
Number of transferred inbound calls answered ))
Avg Wait Time
Average waiting duration(Waiting duration of connected calls/
Number of calls answered)
Avg Abd Time
Average waiting duration of abandoned calls(Waiting duration of
abandoned calls/Number of abandoned calls)
Ans Ratio
98
Answer ratio(Number of calls answered/Number of inbound calls * 100)
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
UCD Group Incoming Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on UCD inbound calls of a specific UCD group. Select the UCD
Group Inbound Statistics submenu of the UCD menu.
Select the target time period and UCD group from the execution options and
click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Group NO
Group number
Group Name
Name of a station group. Blank if not available
Time
Time(The first and last rows indicate detailed time.)
Agent Cnt
Number of agents
Login Agent Cnt
Number of agents logged in
In Cnt
Number of inbound calls
Ans Cnt
Number of calls answered
Abd Call Cnt
Number of abandoned calls
Overflow In Cnt
Number of overflow inbound calls
Overflow Out Cnt
Number of overflow outbound calls
Force Log Out Cnt
Number of forced logout cases
Xfer In Ans Cnt
Number of transferred inbound calls answered
Call Time
Call duration
© SAMSUNG Electronics Co., Ltd.
99
Ошибка! Стиль не определен.
Column
Description
Group NO
Group number
Avg Call Time
Average call duration(Call duration/(Number of calls answered +
Number of transferred inbound calls answered ))
Avg Wait Time
Average waiting duration(Waiting duration of connected calls/
Number of calls answered)
Avg Abd Time
Average waiting duration of abandoned calls(Waiting duration of
abandoned calls/Number of abandoned calls)
Ans Ratio
Answer ratio(Number of calls answered/Number of inbound calls *
100)
100
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
UCD Overall Agent Incoming Statistics
This menu allows you to verify the overall agent statistics and the time-based
statistics on UCD inbound calls. Select the UCD Overall Agent Inbound
Statistics submenu of the UCD menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
Group Cnt
Number of groups
Agent Cnt
Number of agents
Login Cnt
Number of agents logged in
In Cnt
Number of inbound calls
Ans Cnt
Number of calls answered
Consult Cnt
Number of consultation
Xfer Cnt
Number of transfers
Group Xfer Cnt
Number of group transfers
Force Log Out Cnt
Number of forced logout cases
Xfer In Ans Cnt
Number of transferred inbound calls answered
Login Time
Login time
Call Time
Call duration
Consult Time
Consultation duration
© SAMSUNG Electronics Co., Ltd.
101
Ошибка! Стиль не определен.
UCD Agent Incoming Statistics by Group
This menu allows you to verify the overall agent statistics and the group-based
statistics on UCD inbound calls. Select the UCD Agent Inbound Statistics by
Group submenu of the UCD menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
102
Description
Group Cnt
Number of groups
Group NO
Group number
Group Name
Name of a station group. Blank if not available
Agent Cnt
Number of agents
Login Agent Cnt
Number of agents logged in
In Cnt
Number of inbound calls
Ans Cnt
Number of calls answered
Consult Cnt
Number of consultation
Xfer Cnt
Number of transfers
Group Xfer Cnt
Number of group transfers
Force Log Out Cnt
Number of forced logout cases
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Column
Description
Xfer In Ans Cnt
Number of transferred inbound calls answered
Login Time
Login time
Call Time
Call duration
Consult Time
Consultation duration
© SAMSUNG Electronics Co., Ltd.
103
Ошибка! Стиль не определен.
UCD Group Agent Incoming Statistics
This menu allows you to verify the overall agent statistics and the agent-based
statistics on UCD inbound calls of a specific UCD group. Select the UCD
Group Agent Inbound Statistics submenu of the UCD menu.
Select the target time period and UCD group from the execution options and
click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
104
Description
Agent Cnt
Number of agents
Agent NO
Agent Number
Agent Name
Name of an agent. Blank if not available
Login Cnt
Number of agents logged in
In Cnt
Number of inbound calls
Ans Cnt
Number of calls answered
Consult Cnt
Number of consultation
Xfer Cnt
Number of transfer
Group Xfer Cnt
Number of group transfer
Force Log Out Cnt
Number of forced logout cases
Xfer In Ans Cnt
Number of transferred inbound calls answered
Login Time
Login time
Call Time
Call duration
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Column
Consult Time
© SAMSUNG Electronics Co., Ltd.
Description
Consultation duration
105
Ошибка! Стиль не определен.
UCD Agent Detailed Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on UCD inbound calls of a specific agent. Select the UCD Agent
Detailed Statistics submenu of the UCD menu.
Select the target time period and agent from the execution options and click
[Query].
Columns of the Total Summary table and Each Time table are described
below:
Column
106
Description
Agent NO
Agent Number
Agent Name
Name of an agent. Blank if not available
Time
Time(The first and last rows indicate detailed time.)
Group Cnt
Number of groups
Login Cnt
Number of agents logged in
In Cnt
Number of inbound calls
Ans Cnt
Number of calls answered
Direct In Cnt
Number of direct inbound calls
Direct In Ans Cnt
Number of direct inbound answers
Out Cnt
Number of outbound calls
Consult Cnt
Number of consultation
Conf Cnt
Number of conferences
Xfer Cnt
Number of transfers
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Group Xfer Cnt
Number of group transfers
Force Log Out Cnt
Number of forced logout cases
Xfer In Ans Cnt
Number of transferred inbound calls answered
Pickup Cnt
Number of calls picked up from other devices
Login Time
Login time
Call Time
Call duration
Direct Call Time
Direct inbound call duration
Out Call Time
Outbound call duration
Consult Time
Consultation duration
Pickup Call Time
Pickup call duration
© SAMSUNG Electronics Co., Ltd.
107
Ошибка! Стиль не определен.
UCD Call Distribution Statistics
This menu allows you to verify the statistics on the distribution of UCD calls
based on call duration and time zone. Select the UCD Call Distribution
Statistics submenu of the UCD menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
108
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
≤1m
Number of calls whose duration is less than or equal to 1 minute
≤2m
Number of calls whose duration is less than or equal to 2 minutes
≤3m
Number of calls whose duration is less than or equal to 3 minutes
≤4m
Number of calls whose duration is less than or equal to 4 minutes
≤5m
Number of calls whose duration is less than or equal to 5 minutes
≤6m
Number of calls whose duration is less than or equal to 6 minutes
>6m
Number of calls whose duration is greater than 6 minutes
Total Cnt
Total number of calls
Avg Call Time
Average call duration
Max Call Time
Maximum call duration
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
UCD Call Distribution Stat. by Group
This menu allows you to verify the statistics on the distribution of UCD calls
based on call duration and group. Select the UCD Call Distribution Stat. by
Group submenu of the UCD menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Group Cnt
Total number of groups
Group NO
Group Number
Group Name
Name of a station group. Blank if not available
≤1m
Number of calls whose duration is less than or equal to 1 minute
≤2m
Number of calls whose duration is less than or equal to 2 minutes
≤3m
Number of calls whose duration is less than or equal to 3 minutes
≤4m
Number of calls whose duration is less than or equal to 4 minutes
≤5m
Number of calls whose duration is less than or equal to 5 minutes
≤6m
Number of calls whose duration is less than or equal to 6 minutes
>6m
Number of calls whose duration is greater than 6 minutes
Total Cnt
Total number of calls
Avg Call Time
Average call duration
Max Call Time
Maximum call duration
© SAMSUNG Electronics Co., Ltd.
109
Ошибка! Стиль не определен.
110
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
UCD Wait Distribution Statistics
This menu allows you to verify the statistics on the distribution of UCD calls
based on the wait time and time zone. Select the UCD Wait Distribution
Statistics submenu of the UCD menu.
Select the target time period and type from the execution options and click
[Query]. Answer of Type is the waiting duration of an answered call, and
Abandon of Type is of an abandoned call.
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows indicate detailed time.)
≤ 10 s
Number of waiting cases whose duration is less than or equal to
10 seconds
≤ 20 s
Number of waiting cases whose duration is less than or equal to
20 seconds
≤ 40 s
Number of waiting cases whose duration is less than or equal to
40 seconds
≤ 60 s
Number of waiting cases whose duration is less than or equal to
60 seconds
≤ 80 s
Number of waiting cases whose duration is less than or equal to
80 seconds
≤ 100 s
Number of waiting cases whose duration is less than or equal to
100 seconds
© SAMSUNG Electronics Co., Ltd.
111
Ошибка! Стиль не определен.
≤ 120 s
Number of waiting cases whose duration is less than or equal to
120 seconds
> 120 s
Number of waiting cases whose duration is greater than 120
seconds
112
Total Cnt
Total number of waiting cases
Avg Call Time
Average waiting duration
Max Call Time
Maximum waiting duration
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
UCD Wait Distribution Stat. by Group
This menu allows you to verify the statistics on the distribution of UCD calls
based on wait time and group. Select the UCD Wait Distribution Stat. by
Group submenu of the UCD menu.
Select the target time period and type from the execution options and click
[Query]. Answer of Type is the waiting duration of an answered call, and
Abandon of Type is of an abandoned call.
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Group Cnt
Number of groups
Group NO
Group Number
Group Name
Name of a station group. Blank if not available
≤ 10 s
Number of waiting cases whose duration is less than or equal to
10 seconds
≤ 20 s
Number of waiting cases whose duration is less than or equal to
20 seconds
≤ 40 s
Number of waiting cases whose duration is less than or equal to
40 seconds
≤ 60 s
Number of waiting cases whose duration is less than or equal to
60 seconds
≤ 80 s
Number of waiting cases whose duration is less than or equal to
80 seconds
© SAMSUNG Electronics Co., Ltd.
113
Ошибка! Стиль не определен.
Column
≤ 100 s
Description
Number of waiting cases whose duration is less than or equal to
100 seconds
≤ 120 s
Number of waiting cases whose duration is less than or equal to
120 seconds
> 120 s
Number of waiting cases whose duration is greater than 120
seconds
114
Total Cnt
Total number of waiting cases
Avg Call Time
Average waiting duration
Max Call Time
Maximum waiting duration
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
UCD Group Abandoned Call List
This menu allows you to verify the list of abandoned calls of a UCD group.
Select the UCD Group Abandoned Call List submenu of the UCD menu.
Select the target time period and UCD group from the execution options and
click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Group NO
Group number
Group Name
Name of a station group. Blank if not available
In Cnt
Number of inbound calls
Abd Call Cnt
Number of abandoned calls
Overflow In Cnt
Number of overflow inbound calls
Abd Wait Time
Waiting time for abandoned calls
Avg Abd Wait Time
Average waiting duration of abandoned calls(Waiting duration of
abandoned calls/Number of abandoned calls)
Abandoned Ratio
Abandoned call ratio(Number of abandoned calls/Number of
inbound calls * 100)
NO
Record number
Begin Time
Start time
In Tel NO
Inbound phone number
© SAMSUNG Electronics Co., Ltd.
115
Ошибка! Стиль не определен.
Column
116
Description
Group NO
Group number
DID NO
DID number
CID NO
CID number
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Operator Statistics
This menu allows you to verify the statistics on operator information of the
OfficeServ system.
Operator Group Overall Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on inbound operator calls. Select the Operator Group Overall
Statistics submenu of the Operator menu.
Set the options in the execution options, and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Ring Plan Cnt
Number of applied ring plans
Group Cnt
Number of groups
Time
Time(The first and last rows display detailed time.)
Ring Plan
Ring Plan
Group NO
Group Number
Total Line
Total number of lines
Fault Line
Number of faulty lines
Use Line
Number of lines available
© SAMSUNG Electronics Co., Ltd.
117
Ошибка! Стиль не определен.
Column
118
Description
In Req Cnt
Number of required inbound calls
In Succ Cnt
Number of successful inbound calls
All Busy Fail Cnt
Busy faulty count
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Column
Description
ETC Fail Cnt
Number of other failures
In Answer Cnt
Number of answered inbound calls
In No Answer Cnt
Number of unanswered inbound calls
In Xfer Cnt
Number of inbound transfer calls
In Seize Time
Seizure duration of inbound calls
In Call Time
Inbound call duration
Avg In Seize Time
Average seizure duration of inbound calls(Seizure duration of
inbound calls/number of successful inbound calls)
Avg In Call Time
Average call duration of inbound calls(Duration of inbound calls/
number of times that inbound calls have been answered)
In Succ Ratio
Ratio of successful inbound calls(Number of successful inbound
calls/number of required inbound calls * 100)
In Answer Ratio
Ratio of answered inbound calls(Number of answered inbound
calls/number of successful inbound calls * 100)
© SAMSUNG Electronics Co., Ltd.
119
Ошибка! Стиль не определен.
Operator Group Detailed Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on inbound operator calls. Select the Operator Group Detailed
Statistics submenu of the Operator menu.
Set the options in the execution options, and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
120
Description
Record Cnt
Total number of records
Ring Plan Cnt
Number of applied ring plans
Group Cnt
Number of groups
Time
Time(The first and last rows display detailed time.)
Ring Plan
Ring Plan
Group NO
Group Number
Internal Inbound
Internal inbound
External Inbound
External inbound
In Req Cnt
Number of required inbound calls
In Succ Cnt
Number of successful inbound calls
Ans Cnt
Number of answers
Xfer Cnt
Transfer count
Seize Time
Seizure duration
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Column
Description
Call Time
Call duration
Avg Call Time
Average call duration(Call duration/number of answers)
In Succ Ratio
Ratio of successful inbound calls(Number of successful inbound
calls/number of required inbound call * 100)
Ans Ratio
Ratio of answers(Number of answers/number of successful
inbound calls * 100)
© SAMSUNG Electronics Co., Ltd.
121
Ошибка! Стиль не определен.
Operator Distribution Statistics
This menu allows you to verify the time-based distribution statistics on
operator calls. Select the Operator Call Duration Statistics submenu of the
Operator menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows display detailed time.)
≤ 30 s
Number of calls whose duration is less than or equal to 30
seconds
≤ 60 s
Number of calls whose duration is less than or equal to 60
seconds
≤ 90 s
Number of calls whose duration is less than or equal to 90
seconds
≤2m
Number of calls whose duration is less than or equal to 2 minutes
≤3m
Number of calls whose duration is less than or equal to 3 minutes
≤4m
Number of calls whose duration is less than or equal to 4 minutes
≤5m
Number of calls whose duration is less than or equal to 5 minutes
≤ 10 m
Number of calls whose duration is less than or equal to 10
minutes
≤ 20 m
Number of calls whose duration is less than or equal to 20
minutes
≤ 30 m
Number of calls whose duration is less than or equal to 30
minutes
122
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
> 30 m
Number of calls whose duration is greater than 30 minutes
Total Cnt
Total number of calls
© SAMSUNG Electronics Co., Ltd.
123
Ошибка! Стиль не определен.
Operator Distribution Stat. by Ring Plan
This menu allows you to verify the statistics on operator calls based on time
and ring plans. Select the Call Duration Statistics by Operator Ring Plan of the
Operator menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Ring Plan Cnt
Number of applied ring plans
Ring Plan
Ring plan
Time
Time(The first and last rows display detailed time.)
≤ 30 s
Number of calls whose duration is less than or equal to 30
seconds
≤ 60 s
Number of calls whose duration is less than or equal to 60
seconds
≤ 90 s
Number of calls whose duration is less than or equal to 90
seconds
≤2m
Number of calls whose duration is less than or equal to 2 minutes
≤3m
Number of calls whose duration is less than or equal to 3 minutes
≤4m
Number of calls whose duration is less than or equal to 4 minutes
≤5m
Number of calls whose duration is less than or equal to 5 minutes
≤ 10 m
Number of calls whose duration is less than or equal to 10
minutes
≤ 20 m
Number of calls whose duration is less than or equal to 20
minutes
≤ 30 m
Number of calls whose duration is less than or equal to 30
minutes
124
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Column
Description
> 30 m
Number of calls whose duration is greater than 30 minutes
Total Cnt
Total number of calls
© SAMSUNG Electronics Co., Ltd.
125
Ошибка! Стиль не определен.
Operator Port Statistics by Port
This menu allows you to verify the overall statistics on operator calls and
statistics by operator port. Select the Statistics by Operator Port submenu of
the Operator menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Port Cnt
Port number
Port Tel
Port telephone number
Port Name
Name of a station. Blank if not available
Ring Plan Cnt
Number of applied ring plans
Group Cnt
Number of groups
In Cnt
Number of inbound calls
Xfer In Cnt
Number of transfer inbound calls
In Answer Cnt
Number of answered inbound calls
Xfer Cnt
Transfer count
In Seize Time
Inbound seizure duration
In Call Time
Inbound call duration
Avg In Seize Time
Average inbound seizure duration(Inbound seizure duration/
number of successful inbound calls)
126
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Column
Avg In Call Time
Description
Average inbound call duration(Inbound call duration/number of
times that inbound calls have been answered)
In Answer Ratio
Ratio of answered inbound calls(Number of answered inbound
calls/number of successful inbound calls * 100)
© SAMSUNG Electronics Co., Ltd.
127
Ошибка! Стиль не определен.
Operator Port Detailed Stat. by Port
This menu allows you to verify the overall statistics on operator calls and
statistics by port. Select the Detailed Statistics by Operator Port submenu of
the Operator menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
128
Description
Port Cnt
Port number
Port Tel
Port telephone number
Port Name
Name of a station. Blank if not available
Ring Plan Cnt
Number of applied ring plans
Group Cnt
Number of groups
Internal Inbound
Internal inbound
External Inbound
External inbound
In Cnt
Number of inbound calls
Xfer In Cnt
Number of transfer inbound calls
Ans Cnt
Number of answers
Call Time
Call duration
Avg Call Time
Average call duration(Call duration/number of answers)
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Column
Ans Ratio
© SAMSUNG Electronics Co., Ltd.
Description
Answer ratio(Number of answers/number of inbound calls * 100)
129
Ошибка! Стиль не определен.
Miscellaneous
This menu allows you to verify the miscellaneous statistical data on the
OfficeServ system.
VMAA/AA/Cadence Group Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on VMAA/AA/Cadence inbound calls. Select the
VMAA/AA/Cadence Group Statistics submenu of the Miscellaneous menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
130
Description
Record Cnt
Total number of records
Time
Time(The first and last rows display detailed time.)
Total Port
Total number of ports
Fault Port
Number of faulty ports
Use Port
Number of ports available
In Req Cnt
Number of required inbound calls
In Succ Cnt
Number of successful inbound calls
In Xfer Cnt
Number of inbound transfer calls
Simple Inquire Cnt
Simple inquired number
Xfer Req Cnt
Number of required transfer
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Column
Description
Xfer Fail Cnt
Number of transfer failures
Xfer Succ Cnt
Number of successful transfer
© SAMSUNG Electronics Co., Ltd.
131
Ошибка! Стиль не определен.
Column
Description
Seize Time
Seizure duration
Simple Inquire Time
Simple inquired duration
Avg Seize Time
Average seizure duration(Seizure duration/number of
successful inbound calls)
Avg Simple Inquire
Average simple inquired duration(Simple inquired duration/
Time
simple inquired number)
Seize Succ Ratio
Ratio of successful seizure(Number of successful inbound
calls/number of required inbound calls * 100)
Xfer Succ Ratio
Ratio of successful transfer(Number of successful transfer/
number of required transfer * 100)
132
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
VMAA/AA/Cadence Xfer Fail Statistics
This menu allows you to verify the overall statistics and the time-based
statistics on VMAA/AA/Cadence transfer failures. Select the
VMAA/AA/Cadence Transfer Fail Statistics submenu of the Miscellaneous
menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
Record Cnt
Total number of records
Time
Time(The first and last rows display detailed time.)
Xfer Req Cnt
Number of required transfer
Xfer Fail Cnt
Number of transfer failures
Xfer Fail Ratio
Ratio of transfer(number of transfer failures/number of required
transfer * 100)
Invalid
Invalid number
Busy
Busy
DND
DND
No More
Called Station is no more existed
Plug Out
Plug out
Device Mismatch
Device mismatch
No Answer
No answer
Abandoned
Abandoned
Etc
Others
© SAMSUNG Electronics Co., Ltd.
133
Ошибка! Стиль не определен.
Statistics by DID
This menu allows you to verify the overall statistics on DID inbound calls and
the statistics by DID. Select the Statistics by DID submenu of the
Miscellaneous menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
DID Cnt
DID count
DID NO
DID Number
Seize Cnt
Seizure count
Answer Cnt
Number of answers
Abandoned Call Cnt
Number of abandoned calls
Answer Ratio
Ratio of answers(Number of answers/seizure number * 100)
Trunk Seize Time
Trunk seizure duration
Call Time
Call duration
Avg Trunk Seize Time
Average trunk seizure duration(Trunk seizure duration/number
of seizure)
Avg Call Time
134
Average call duration(Call duration/number of answers)
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Detailed DID Statistics
This menu allows you to verify the overall statistics on DID inbound calls and
the statistics by DID. Select the Detailed DID Statistics submenu of the
Miscellaneous menu.
Select the target time period from the execution options and click [Query].
Columns of the Total Summary table and Each Time table are described below:
Column
Description
DID NO
DID Number
Time
Time(The first and last rows display detailed time.)
Seize Cnt
Seizure count
Answer Cnt
Number of answers
Abandoned Call Cnt
Number of abandoned calls
Answer Ratio
Ratio of answers(Number of answers/seizure number * 100)
Trunk Seize Time
Trunk seizure duration
Call Time
Call duration
Avg Trunk Seize Time
Average trunk seizure duration(Trunk seizure duration/number
of seizure)
Avg Call Time
© SAMSUNG Electronics Co., Ltd.
Average call duration(Call duration/number of answers)
135
Ошибка! Стиль не определен.
This page is intentionally left blank.
136
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide
CHAPTER 5. Monitoring
This chapter describes the monitoring function of the OfficeServ DataView Web page.
Monitoring Window Layout
You can use the monitoring function after connecting and logging in to the
OfficeServ DataView homepage.
The general layout of a monitoring window is shown below:
Additional Menus
Page Title
Execution Options
Sum
Detailed Results
Sum
Detailed Result
© SAMSUNG Electronics Co., Ltd.
137
Ошибка! Стиль не определен.
Page Title
The selected submenu is displayed as the title.
Additional Menus
The three menus below are provided as additional menus. Refer to the
‘Additional Menu’ section of this chapter for detailed descriptions.
Menu
Description
Creates a new window for monitoring.
Execution Options
This section of the window allows you to set a monitoring option and to start
or stop the monitoring process. The [Interval] option is applied to all
monitoring pages, which are refreshed at each set interval time. Additional
conditions may be provided depending on the monitoring item.
Sum
This section of the window displays the sum of each item being monitored.
Detailed Results
This section of the window displays detailed monitoring results for the
selected submenu.
138
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Selecting a Monitoring Item
Monitoring windows display information on call events that occur in the
OfficeServ system, based on various criteria such as trunk and station. You can
select a monitoring item by placing the mouse pointer over a main menu and
clicking a submenu from the list displayed.
Monitoring Item
Monitoring items are categorized into four main menus, Trunk, Station, UCD,
and Miscellaneous, and are further categorized into fifteen submenus.
© SAMSUNG Electronics Co., Ltd.
139
Ошибка! Стиль не определен.
Additional Menus
New Page
Click the New(
) icon to view the current monitoring window from a new
page. This function helps you to monitor multiple items simultaneously. The
following figure shows an example of clicking the New icon of a Trunk Group
Status window.
140
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Trunk Monitoring
This function is used for monitoring the trunk status of the OfficeServ system.
Trunk Group Status
This menu allows you to monitor the overall status of trunk groups and the
status of each group. Select the Trunk Group Status submenu of the Trunk
menu.
Click [Start] from the execution options to start the monitoring.
Columns of the Total Summary table and the Each Group table are described
below:
Column
Description
Group Count
Total number of groups
Group NO
Group Number
Total Line
Total number of lines
Fault Line
Number of faulty lines
Available Line
Number of lines available
Busy Cnt
Number of busy lines
In Seize Cnt
Inbound seize count
Out Seize Cnt
Outbound seize count
Busy Ratio
Line usage(Number of busy lines/Number of lines available * 100)
Group In Cnt
Number of Group Incoming calls
© SAMSUNG Electronics Co., Ltd.
141
Ошибка! Стиль не определен.
Trunk Group Port Status
This menu allows you to monitor the status of a selected trunk group and the
status of each trunk port of the group. Select the Trunk Group Port Status
submenu of the Trunk menu.
Select a group from the execution options and click [Start].
Columns of the Total Summary table and the Each Group table are described
below:
Column
142
Description
Total Line
Total number of lines
Fault Line
Number of faulty lines
Available Line
Number of lines available
Busy Cnt
Number of busy lines
In Seize Cnt
Inbound seize count
Out Seize Cnt
Outbound seize count
Busy Ratio
Line usage(Number of busy lines/Number of lines available * 100)
Group In Cnt
Number of Group Incoming calls
NO
Record Number
Port Tel
Port Number
Port Type
Port type
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Port Status
Port status
Call Status
Call status
Duration
Duration
Opp Tel
Telephone number of the opposite party
© SAMSUNG Electronics Co., Ltd.
143
Ошибка! Стиль не определен.
Trunk Port Status by Scope
This menu allows you to monitor the trunk port status for a selected scope.
Select the Trunk Port Status by Scope submenu of the Trunk menu.
Enter the range of trunk ports in the execution options and click [Start].
Columns of the Total Summary table and the Each Group table are described
below:
Column
144
Description
NO
Record Number
Port Tel
Port Number
Port Type
Port type
Port Status
Port status
Call Status
Call status
Duration
Duration
Opp Tel
Telephone number of the opposite party
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Trunk Port Status by Time
This menu allows you to monitor the trunk port status for a selected time.
Select the Trunk Port Status by Time submenu of the Trunk menu.
Enter the range of trunk ports and select the duration of the trunk port, and
click [Start].
Columns of the Total Summary table and the Each Group table are described
below:
Column
Description
NO
Record Number
Port Tel
Port Number
Port Type
Port type
Port Status
Port status
Call Status
Call status
Duration
Duration
Opp Tel
Telephone number of the opposite party
© SAMSUNG Electronics Co., Ltd.
145
Ошибка! Стиль не определен.
Station Monitoring
This function is used for monitoring the station status of the OfficeServ
system.
Station Group Status
This menu allows you to monitor the overall status of station groups and the
status of each group. Select the Station Group Status submenu of the Station
menu.
Click [Start] from the execution options to start the monitoring.
Columns of the Total Summary table and the Each Group table are described
below:
Column
146
Description
Group Count
Total number of groups
Group NO
Group Number
Total Line
Total number of lines
Fault Line
Number of faulty lines
Available Line
Number of lines available
Busy Cnt
Number of busy lines
In Seize Cnt
Inbound seize count
Out Seize Cnt
Outbound seize count
Busy Ratio
Line usage(Number of busy lines/Number of lines available *
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
100)
Group In Cnt
© SAMSUNG Electronics Co., Ltd.
Number of Group Incoming calls
147
Ошибка! Стиль не определен.
Station Group Port Status
This menu allows you to monitor the status of a selected station group and the
status of each station port of the group. Select the Station Group Port Status
submenu of the Station menu.
Select a group from the execution options and click [Start].
Columns of the Total Summary table and the Each Group table are described
below:
Column
148
Description
Total Line
Total number of lines
Fault Line
Number of faulty lines
Available Line
Number of lines available
Busy Cnt
Number of busy lines
In Seize Cnt
Inbound seize count
Out Seize Cnt
Outbound seize count
Busy Ratio
Line usage(Number of busy lines/Number of lines available * 100)
Group In Cnt
Number of Group Incoming calls
NO
Record Number
Port Tel
Port Number
Port Type
Port type
Port Status
Port status
Call Status
Call status
Duration
Duration
Opp Tel
Telephone number of the opposite party
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
© SAMSUNG Electronics Co., Ltd.
149
Ошибка! Стиль не определен.
Station Port Status by Scope
This menu allows you to monitor the station port status for a selected scope.
Select the Station Port Status by Scope submenu of the Station menu.
Enter the range of station ports in the execution options and click [Start].
Columns of the Total Summary table and the Each Group table are described
below:
Column
150
Description
NO
Record Number
Port Tel
Port Number
Port Type
Port type
Port Status
Port status
Call Status
Call status
Duration
Duration
Opp Tel
Telephone number of the opposite party
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Station Port Status by Time
This menu allows you to monitor the station port status for a selected time.
Select the Station Port Status by Time submenu of the Station menu.
Enter the range of station ports and select the duration of the station port, and
click [Start].
Columns of the Total Summary table and the Each Group table are described
below:
Column
Description
NO
Record Number
Port Tel
Port Number
Port Type
Port type
Port Status
Port status
Call Status
Call status
Duration
Duration
Opp Tel
Telephone number of the opposite party
© SAMSUNG Electronics Co., Ltd.
151
Ошибка! Стиль не определен.
UCD Monitoring
This function is used for monitoring the UCD status of the OfficeServ system.
UCD Call Status
This menu allows you to monitor the overall status of UCD groups and the
call status of a UCD group. Select the UCD Call Status submenu of the UCD
menu.
Click [Start] from the execution options to start the monitoring.
Columns of the Total Summary table and the Each Group table are described
below:
Column
152
Description
Group Count
Total number of groups
Group NO
Group Number
Agent Cnt
Number of agents
Login Cnt
Number of agents logged in
In Call Cnt
Number of inbound calls
Queued Cnt
Number of queued calls
Answer Cnt
Number of calls answered
Group In Cnt
Number of Group Incoming calls
Group In Ans Cnt
Group Incoming answered count
Answer Ratio
Response rate(Number of calls answered / Number of inbound
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
calls * 100)
© SAMSUNG Electronics Co., Ltd.
153
Ошибка! Стиль не определен.
UCD Agent Status
This menu allows you to monitor the overall agent status of UCD groups and
the agent status of a UCD group. Select the UCD Agent Status submenu of the
UCD menu.
Click [Start] from the execution options.
Columns of the Total Summary table and the Each Group table are described
below:
Column
154
Description
Group Count
Total number of groups
Group NO
Group Number
Agent Cnt
Number of agents
Login Cnt
Number of agents logged in
Log Out Cnt
Number of agents logged out
Busy Cnt
Number of busy agents
Busy Ratio
Call rate(Number of busy agents/Number of agents logged in * 100)
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
UCD Group Agent Status
This menu allows you to monitor the status of a UCD group and the status of
agents assigned to the UCD group. Select the UCD Group Agent Status
submenu of the UCD menu.
Click [Start] from the execution options.
Columns of the Total Summary table and the Each Group table are described
below:
Column
Description
Agent Cnt
Number of agents
Login Cnt
Number of agents logged in
Log Out Cnt
Number of agents logged out
Busy Cnt
Number of busy agents
Busy Ratio
Call rate(Number of busy agents/Number of agents logged in * 100)
NO
Record Number
Port Tel
Port Number
Port Status
Port status
Agent Status
Agent status
Call Status
Call status
Duration
Duration
Opp Tel
Telephone number of the opposite party
© SAMSUNG Electronics Co., Ltd.
155
Ошибка! Стиль не определен.
Miscellaneous
This function is used for monitoring miscellaneous statuses of the OfficeServ
system.
Operator Group Status
This menu allows you to monitor an operator group status. Select the Operator
Group Status submenu of the Miscellaneous menu.
Click [Start] from the execution options to start the monitoring.
Columns of the Total Summary table and the Each Group table are described
below:
Column
Description
Ring Plan
Ring Plan Number
Group
Operator Group Number
Total Line
Total number of lines
Fault Line
Number of faulty lines
Available Line
Number of lines available
In Call Cnt
Number of inbound calls
Queued Cnt
Number of queued calls
Answer Cnt
Number of calls answered
Group In Cnt
Number of Group Incoming calls
Answer Ratio
Response rate(Number of calls answered/Number of inbound
calls * 100)
156
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
NO
Record Number
Port Tel
Port Number
Port Type
Port type
Port Status
Port status
Call Status
Call status
Duration
Duration
Opp Tel
Telephone number of the opposite party
AA/VMAA Group Status
This menu allows you to monitor an AA/VMAA group status. Select the
AA/VMAA Group Status submenu of the Miscellaneous menu.
Click [Start] from the execution options.
Columns of the Total Summary table and the Each Group table are described
below:
Column
Description
Group Count
Total number of groups
Group NO
Group Number
Total Line
Total number of lines
Fault Line
Number of faulty lines
Available Line
Number of lines available
In Call Cnt
Number of inbound calls
© SAMSUNG Electronics Co., Ltd.
157
Ошибка! Стиль не определен.
Queued Cnt
Number of queued calls
Answer Cnt
Number of calls answered
Answer Ratio
Response rate(Number of calls answered/Number of inbound
calls * 100)
Group In Cnt
158
Number of Group Incoming calls
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
AA/VMAA Group Port Status
This menu allows you to monitor an AA/VMAA group port status. Select the
AA/VMAA Group Port Status submenu of the Miscellaneous menu.
Select a group from the execution options and click [Start].
Columns of the Total Summary table and the Each Group table are described
below:
Column
Description
Group Count
Total number of groups
Group NO
Group Number
Total Line
Total number of lines
Fault Line
Number of faulty lines
Available Line
Number of lines available
In Call Cnt
Number of inbound calls
Queued Cnt
Number of queued calls
Answer Cnt
Number of calls answered
Answer Ratio
Response rate(Number of calls answered/Number of inbound
calls * 100)
Group In Cnt
© SAMSUNG Electronics Co., Ltd.
Number of Group Incoming calls
159
Ошибка! Стиль не определен.
Wall board
Go to 'Configuration->Personalize->Set Wallboard' to set the wallboard
contents and thresholds.
Columns of the Wall Board table is described below:
필드명
설명
Trunk Total Line
Total number of Trunk
Trunk Fault Line
Number of Trunk faulty lines
Trunk Available Line
Number of Trunk Available lines
Trunk Busy Cnt
Number of Trunk Busy
Trunk In Seize Cnt
Number of Trunk Inbound Seize
Trunk Out Seize Cnt
Number of Trunk Outbound Seize
Trunk Busy Ratio
Trunk Busy Rate
Trunk Group In Cnt
Number of Trunk Group In
Trunk Longest Seize Time
The longest seize time among the trunk currently in
use
UCD Agent Cnt
160
Number of UCD Agent
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
UCD Login Cnt
Number of UCD Login
UCD Log Out Cnt
Number of UCD Log Out
UCD Busy Cnt
Number of UCD Busy
UCD Busy Ratio
Ratio of UCD Busy
UCD In Call Cnt
Number of UCD In Call Cnt
UCD Queued Cnt
Number of UCD Queued
UCD Answer Cnt
Number of UCD Answer
UCD Group In Cnt
Number of Group In
UCD Group In Ans Cnt
Number of Group In Ans
UCD Group In Ans Ratio
UCD Group In Ans Rate
UCD Longest Connected Time
UCD Longest Wait Time
© SAMSUNG Electronics Co., Ltd.
The longest talk time among the currently answered
UCD calls
The longest wait among the currently ringing UCD
calls
161
Ошибка! Стиль не определен.
This page is intentionally left blank.
162
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide
CHAPTER 6. Scheduled Report
This chapter describes the scheduled report function of the OfficeServ DataView Web site.
Scheduled reports include trunk reports and UCD reports designated by a user. Refer to ‘Chapter
4. Statistics’ for descriptions report items.
Scheduled Report Window Layout
The general layout of a scheduled report window is shown below:
Page Title
Item Title
Creation Date
Period
Sum
Detailed
Results
Page Title
서브메뉴에서 선택한 리포트의 제목이 표시됩니다.
주기 리포트에는 일간 국선 리포트, 일간 UCD 리포트, 주간 국선
리포트, 주간 UCD 리포트, 월간 국선 리포트, 월간 UCD 리포트가
있습니다.
Period
통계 데이터를 수집한 기간을 나타냅니다. 위 그림에서는 2005 년 01
월 10 일 00:00 분부터 2005 년 01 월 10 일 23:45 분까지의 통계 데이
© SAMSUNG Electronics Co., Ltd.
163
Ошибка! Стиль не определен.
터를 보여주고 있습니다. 주기 리포트의 기간은 [환경 구성] 메뉴의
[주기 리포트 설정] 에서 설정할 수 있습니다.
Creation Date
주기 리포트가 생성된 날짜와 시간이 표시됩니다. 주기 리포트 생성
날짜는 [환경 구성] 메뉴의 [주기 리포트 설정] 에서 설정할 수 있으
며 Scheduler 에서 확인할 수 있습니다.
Item Title
주기 리포트의 종류를 나타냅니다. 리포트의 종류는 [환경 구성] 메
뉴의 [주기 리포트 설정]의 일간/주간/월간리포트 설정 부분을 참고
하십시오.
Sum
This section of the window displays the sum of each statistical item.
Detailed Results
This section of the window displays detailed scheduled report data for the
selected submenu
164
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide
CHAPTER 7. Troubleshooting
This chapter provides information on problems that may occur during the installation and operation
of OfficeServ DataView, and describes proper actions against each problem.
ODBC Version Error
Symptom
An error message related to ODBC(Open Database Connectivity) appears on
the window.
Cause
In order to use the OfficeServ DataView program with MDB, the version of
Microsoft Access Driver(*.mdb) must be 4.0 or later. Although the Microsoft
Access Driver 4.0 for ODBC is automatically installed during the installation
of OfficeServ DataView, the driver may not have been automatically installed
on certain types of PC.
Resolution
Connect to the Microsoft site and download the latest version of Microsoft jet
Driver. Install the driver on the PC and restart the OfficeServ DataView
program.
© SAMSUNG Electronics Co., Ltd.
165
Ошибка! Стиль не определен.
I cannot open the monitoring pages!
Symptom
When you select any of the Monitoring pages, you encounter error page with
the following description:
Server object error 'ASP 0178 : 80070005'
Server.CreateObject Access Error
The call to Server.CreateObject failed while checking permissions. Access is denied
to this object.
Cause
The authenticated user for the Visual Basic (VB) run-time file (Msvbvm60.dll)
does not have sufficient permissions. The authenticated user is the
IUSR_computername account when you use anonymous access or the user
that is authenticated with the Web page.
Resolution
Click [Start] button, and select [Programs] -> [Administrative Tools] ->
[Internet Service Manager].
Collapse [Default Web Site] folder and select [DataView] web application.
Right click the mouse button and select [Properties] option.
Then you will get the [DataView Properties] dialog open.
166
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
Set the [Application Permission] option as ‘Low (IIS Process)’.
Click [OK].
© SAMSUNG Electronics Co., Ltd.
167
Ошибка! Стиль не определен.
I cannot save the Scheduled Report options!
Symptom
When you select any of [Set Daily/Weekly/Monthly Report] pages, set options,
and click the [Save] button, you will see the options are reset to the defaults.
Cause
The IUSR_computername account does not have sufficient permissions to
access configuration file. Or the configuration file is set read only when it is
copied to the DataView server computer.
Resolution
Run the Windows Explorer, and collapse the [DataView] folder under the
OfficeServ DataView program folder.
Select the [ScheduledReport] folder and click the right mouse button.
Select [Properties] option. Then you will get the [Scheduled Report
Properties] window open.
168
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
If the ‘Read-only attribute’ is set, clear it.
Select the [Security] tab.
Add ‘Internet Guest Account’ (IUSR_computername) and give ‘Full Control’
to that account. Click [OK].
© SAMSUNG Electronics Co., Ltd.
169
Ошибка! Стиль не определен.
Select ‘Day’, ‘Week’, ‘Month’ folders and schedule.ini file in the
[ScheduledReport] folder and right click the mouse button.
Select [Properties] option.
Confirm that the ‘Read-only’ attribute is not set.
170
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
I cannot add/delete/modify accounts!
This case is only applicable to the OfficeServ DataView with MDB.
Symptom
When you try to add, delete, or modify user accounts, you encounter error
page with the following description:
Microsoft JET Database Engine (0x80004005)
Operation must use an updateable query.
filename, line number
Cause
The IUSR_computername account does not have sufficient permissions to
access MDB file.
Resolution
Run the Windows Explorer, and select the [DB] folder under the OfficeServ
Dataview program folder.
Click the right mouse button.
© SAMSUNG Electronics Co., Ltd.
171
Ошибка! Стиль не определен.
You will get the [DB Properties] window open.
Select [Security] tab and give full control to the Users group.
Click [OK].
172
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
I cannot save [Personalize] configurations!
This case is only applicable to the OfficeServ DataView with MDB.
Symptom
When you try to save personal options such as ‘Skin’, you encounter error
page with the following description:
Microsoft JET Database Engine (0x80004005)
Operation must use an updateable query.
filename, line number
Cause
The IUSR_computername account does not have sufficient permissions to
access MDB file.
Resolution
The same as “I cannot add/delete/modify accounts!” case
© SAMSUNG Electronics Co., Ltd.
173
Ошибка! Стиль не определен.
I cannot save the exported excel report !
Symptom
When you export a report into excel, it is open with the internet explorer
without any menu or toolbar.
Cause
The ‘XLS’ file is set to be open in the same window that is opening the ‘XLS’
file.
Resolution
Open the Windows Explorer and select [Tools] -> [Folder Option].
The select the [File Types] tab, select [XLS] from the [Registered file types]
list, and click the [Advanced] button
174
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView User Guide/Ed.00
When the [Edit File Type] dialog open, clear this option.
- Browse in same window
© SAMSUNG Electronics Co., Ltd.
175
OfficeServ DataView User Guide
ANNEX A. Abbreviation
A
AA
Automated Attendant
CID
Caller Identification
COM
Component Object Model
CPU
Central Processing Unit
DB
Database
DID
Direct Inward Dialing
C
D
DND
Do Not Disturb
DOD
Direct Outward Dialing
I
ID
Identification
IIS
Internet Information Server
IP
Internet Protocol
LED
Light Emitting Diode
L
N
NetBIOS Network Basic Input Output System
© SAMSUNG Electronics Co., Ltd.
177
Ошибка! Стиль не определен.
NTFS
New Technology File System
MDB
Multimedia Database
MMC
Man Machine Command
ODBC
Open Database Connectivity
OS
Operating System
SQL
Structured Query Language
TCP/IP
Transmission Control Protocol/Internet Protocol
TRK
Trunk
UCD
Universal Call Distribution
UI
User Interface
M
O
S
T
U
V
178
VM
Voice Mail
VMAA
Voice Mail/Automated Attendant
© SAMSUNG Electronics Co., Ltd.
OfficeServ DataView
User Guide
©2004 Samsung Electronics Co., Ltd.
All rights reserved.
Information in this document is proprietary to SAMSUNG
Electronics Co., Ltd.
No information contained here may be copied, translated,
transcribed or duplicated by any form without the prior
written consent of SAMSUNG.