Miele DA 6690 D Operating instructions

Installation Instructions
DA6690 D
en - CA
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.
Installation
Before installation
 Before installing the appliance,
read all of the information contained
in this chapter and also in the "IM‐
PORTANT SAFETY INSTRUCTIONS"
section.
4 extension piece holders
for aligning and securing the telescopic
chimney
Installation parts
4 screws, ¹/₄" x 4 ⁵/₁₆"
(7 x 110 mm) and
4 plugs, ³/₈" x 3 ¹/₈" (10 x 80 mm)
for securing the ventilation hood to the
ceiling (not for use in USA / CDN).
The screws and plugs are designed
for use in solid ceilings only.
Use different fasteners for other ceil‐
ing construction types. Make sure
that the ceiling can support the load.
4 screws M³/₁₆" x ⁵/₁₆"
(M4 x 8.5 mm)
for securing the extension piece hold‐
ers.
14 screws M³/₁₆" x ⁵/₁₆"
(M4 x 8 mm)
for securing the spacer frame and se‐
curing the hood to the installation
frame.
1 screw M³/₁₆" x ⁵/₈" (M4 x 16 mm)
for securing the chimney.
DUI 32 recirculation kit for recircula‐
tion mode
(not supplied, available as an optional
accessory). The kit includes a direc‐
tional unit, aluminum hose, and hose
clips.
31
Installation
Appliance dimensions
a Mounting area for the exhaust ducting and power cable. In recirculation mode,
only the power cord is required.
b Possible height range for appliance in vented mode
c Possible height range for appliance in recirculation mode
d Alternative installation with spacer frame
e Air vent positioned at the top for recirculation
32
Installation
f A power cord is required to connect the hood to the socket in the ceiling. With
extraction mode flexible ducting is also required.
Exhaust connection  6" (150 mm)
Distance between cooktop and ventilation hood (S)
Provided a larger distance is not given by the manufacturer of the cooktop, fol‐
low the minimum safety distances between a cooktop and the bottom of the
hood.
Please also observe the information contained in the "IMPORTANT SAFETY IN‐
STRUCTIONS" section.
Minimum distance S
Cooking appliance
Miele
appliance
Non-Miele
appliance
Electric/Induction cooktop
24" (610 mm)
Electric grill, deep fat fryer (electric)
26" (660 mm)
Multi-burner gas cooktop
≤ 43,000 BTU/hr (12.6 W),
no burner > 15,000 BTU/hr (4.5 kW).
26" (660 mm)
30" (760 mm)
Multi-burner gas cooktop
≤ 73,800 BTU/hr (21.6 W),
no burner > 16,500 BTU/hr (4.8 kW)
30" (760 mm)
Multi-burner gas cooktop
> 73,800 BTU/hr (21.6 W),
or one of the burners > 16,500 BTU/hr (4.8 kW)
Not possible
Single-burner gas cooktop
≤ 20,500 BTU/hr (6 kW)
26" (660 mm)
30" (760 mm)
Single-burner gas cooktop
> 20,500 BTU/hr (6 kW)
≤ 27,600 BTU/hr (8.1 kW)
30" (760 mm)
Single-burner gas cooktop
> 27,600 BTU/hr (8.1 kW)
Not possible
33
Installation
Installation recommendations
Structural support
– We also recommend a distance of at
least 25 ¹/₂" (650 mm) above electric
cooktops to provide more workspace
and easier cooking under the hood.
– When selecting an installation height,
always take the user height into con‐
sideration. Users should have ample
space to work comfortably on the
cooktop and reach the ventilation
hood controls with ease.
– Please note that the greater the dis‐
tance from the cooktop, the less ef‐
fective the hood is at drawing in the
cooking vapors.
– To achieve optimal vapor extraction,
make sure that the hood covers the
cooktop. The hood should be posi‐
tioned centrally over the cooktop, not
to the side or rear.
– The cooktop should be no wider than
the hood. Preferably, it should be
narrower.
– The mounting area must be easily
accessible. The ventilation hood
should be easy to reach and disas‐
semble in case a service call is nec‐
essary. This should be taken into
consideration when planning the po‐
sition of cupboards, shelves, ceilings
or decorative elements in the vicinity
of the ventilation hood.
34
The hood must be attached to rigid
structural framing that is supported
in its entirety by the ceiling joists, or
to the ceiling joists directly. Do not
attach the plate directly to the ceiling
with anchors, toggle bolts, etc.
Removing the protective film
The housing components are covered
by a protective film to prevent them
from becoming damaged during trans‐
port.
 Please remove this film before instal‐
ling the housing components. It can
be peeled off easily without any addi‐
tional tools.
Installation
8
2 5/8
5/8"
8 mm 20 m "
0
m
22
 For vented mode:
dai3435aus
 Draw two intersecting lines on the
ceiling.
– Place a section of the exhaust duct‐
ing in the ceiling and feed it down
through the cross-sectional area as
illustrated. Exhaust ducting of ap‐
prox. 27 ⁹/₁₆" (700 mm) length is re‐
quired between the ceiling and the
hood exhaust socket.
– Secure the exhaust ducting to the ex‐
haust socket, e.g. with a hose clip
(available as an optional accessory)
on flexible ducting.
 Place the power cord and guide it
through the ceiling in the area shown.
A power cord approx. 27 ⁹/₁₆"
(700 mm) in length is required be‐
tween the ceiling and the hood con‐
nectors.
35
Installation
 Use a knife to release the four
spacers and the two covers from the
spacer frame supplied.
 Drill four holes  ³/₈" (10 mm), ap‐
prox. 4 ¹/₂" (115 mm) deep for the
plugs supplied.
 Use the spacer frame as a drilling
template. Place it on the ceiling with
the arrows pointing forwards. Using
the notches, align the spacer frame
on the intersecting lines and make
pencil marks for the drill holes.
36
 Place the four plugs in the holes and
screw in the four screws so that they
protrude by approx. 1 ³/₁₆" (30 mm).
Installation
The spacer frame can be installed be‐
tween the chimney and the ceiling. This
creates a shadow which gives the illu‐
sion of a gap between the ceiling and
the chimney. This is useful if the ceiling
is not level or is uneven. The hood is
aligned vertically with the spacers sup‐
plied. Visual irregularities between the
chimney and the ceiling are then con‐
cealed by the shadow.
 Mount the spacer frame onto the in‐
stallation frame.
 If you wish to install the hood with the
spacer frame, remove the four inserts
from the fixing holes.
37
Installation
 Hang the installation frame on the
four screws. The front of the frame is
marked with a "V".
 If using the spacer frame, place the
two covers into the fixing holes.
38
 Align the installation frame and se‐
cure it with the screws.
The spacers, which were removed
from the spacer frame at the start,
can be used to align the hood verti‐
cally.
Installation
 Holding the installation frame secure‐
ly, remove the two fixing screws and
extend the installation frame to its
maximum length.
 Replace the screws.
The directional unit from recirculation
kit DUI 32 (optional accessory) is instal‐
led for recirculation mode (RM):
 Bend the four retaining tabs on the
installation frame outwards.
 Place the power cord inside the in‐
stallation frame.
 Fit the directional unit as shown, not‐
ing the marking on the front.
 Bend the retaining tabs back and ap‐
prox. 45° inwards to hold the direc‐
tional unit in place.
39
Installation
 Secure the exhaust socket to the
hose using a hose clip.
 Secure the hose to the directional
unit socket using a hose clip.
 Check that the hose is held securely.
 Push the telescopic chimney over the
installation frame:
– with the recirculation grilles at the
bottom for vented mode (AE),
– with the recirculation grilles at the top
for recirculation mode (RM).
 Bend the two retaining tabs outwards
to prevent the telescopic chimney
from slipping down again.
40
Installation
 Fit the four telescopic chimney
clamps. When the screws are tight‐
ened, the clamps spread out and
push the telescopic expansion piece
upwards.
 Bend back the two retaining tabs.
 Push the chimney over the telescopic
chimney and bend the retaining tabs
outwards again to prevent the chim‐
ney from slipping down again.
Tighten the screws only until the top
edge of the telescopic chimney is
evenly aligned with the ceiling or the
spacer frame.
41
Installation
A non-return flap is supplied with the
hood or is already fitted in the exhaust
socket of the motor unit (depending on
model).
 With vented mode (AE) insert the
non-return flap in the exhaust socket
if your ducting system is not equip‐
ped with one.
Recirculation mode (RM) does not re‐
quire the non-return flap to be insert‐
ed. If there is one present, it should
be removed.
 Hang the hood on the brackets, mak‐
ing sure that the controls are at the
front.
 Secure the hood with the screws
supplied.
42
Installation
 Connect the power cord. See "Elec‐
trical connection."
 Unscrew both screws from the instal‐
lation frame again.
 Place the exhaust ducting onto the
exhaust socket.
The canopy can now be adjusted to the
desired height, observing the permissi‐
ble height ranges:
– With vented mode: upwards as far as
it will go, downwards only to the "A"
marking.
– With recirculation mode: upwards as
far as the "U", downwards as far as it
will go.
Follow the instructions in "Appliance
dimensions." Safety distances be‐
tween the cooktop and ventilation
hood must be observed.
43
Installation
 Raise the canopy to the desired
height and secure it with the screws.
 Hold the chimney securely, bend
back the retaining tabs and carefully
lower it.
The chimney will locate in the cut-out in
the canopy.
44
Installation
 With recirculation mode (RM) ventila‐
tion hoods, insert the OdorFree Char‐
coal Filter.
 Remove the grease filters from the
hood.
 Insert the safety screw on the inside.
 Carefully remove the protective foil
from the grease filters.
 Reinsert the grease filters.
45
Exhaust duct
WARNING: Danger of toxic fumes.
Gas cooking appliances release car‐
bon monoxide that can be harmful or
fatal if inhaled.
To reduce the risk of fire and to prop‐
erly exhaust air, the exhaust gases
extracted by the hood should be
vented outside of the building only.
Do not vent exhaust air into spaces
within walls or ceilings or in attics,
crawl spaces or garages.
To reduce the risk of fire, only use
metal ductwork.
Please read and follow the "IMPOR‐
TANT SAFETY INSTRUCTIONS" to
reduce the risk of personal injury.
Follow all local building codes when
installing the hood.
 Only use smooth pipes or flexible
duct hoses made from non-flamma‐
ble materials for exhaust ductwork.
 To achieve the greatest possible air
extraction with the lowest noise lev‐
els, please note the following:
– The diameter of the exhaust duct
should not be less than 6" (150 mm).
– If flat exhaust ducts are used, the
cross section should not be smaller
than that of the exhaust connector.
– The exhaust duct should be as short
and straight as possible.
– If elbows are needed, make sure they
have a large radius.
– The exhaust duct itself must not be
kinked or compressed.
– Make sure that all connections are
secure and airtight.
46
Remember that any constriction of
the airflow will reduce extraction per‐
formance and increase operating
noise.
 If the exhaust duct is to be routed
through an outside wall, we recom‐
mend installing a telescopic wall vent
or a rooftop vent (available as an op‐
tional accessory).
 If the exhaust air is to be conducted
into a vent flue, the intake piece must
be aligned with the flow direction of
the flue.
 When installing the exhaust duct hor‐
izontally, you must slope it away from
the source by at least 1 cm per meter
(³/₈" per 3 ¹/₄"). This ensures that
condensate cannot drain back into
the ventilation hood.
 If the exhaust duct is to be routed
through rooms, ceiling space etc., the
temperatures in these different areas
may differ greatly, which means that
the problem of condensation will
need to be addressed. The exhaust
duct will need to be insulated.
Exhaust duct
Condensate trap
In addition to insulating the exhaust
duct, we recommend installing a con‐
densate trap to collect and evaporate
any condensate which might accumu‐
late.
Condensate traps are available for ex‐
haust ducts with a diameter of 5"
(125 mm) or 6" (150 mm).
 When installing a condensate trap,
make sure that it is positioned verti‐
cally and, if possible, directly above
the hood outlet duct collar.
The arrow on the housing indicates
the direction of airflow.
47
Electrical connection
WARNING: TO REDUCE THE RISK
OF FIRE, ELECTRIC SHOCK, OR IN‐
JURY TO PERSONS, OBSERVE THE
FOLLOWING:
All electrical work should be per‐
formed by a qualified electrician in
strict accordance with national regu‐
lations (for USA: ANSI-NFPA 70) and
local safety regulations. Installation,
repairs and other work by unqualified
persons could be dangerous.
Ensure that power to the appliance is
OFF while installation or repair work
is performed.
Verify that the voltage, load and cir‐
cuit rating information found on the
data plate (located behind the baffle
filters), match the household electri‐
cal supply before installing the hood.
Use only with ventilation hood cordconnection kits that have been in‐
vestigated and found acceptable for
use with this model hood.
If there is any question concerning
the electrical connection of this ap‐
pliance to your power supply, please
consult a licensed electrician or call
Miele’s Technical Service Depart‐
ment.
WARNING: THIS APPLIANCE MUST
BE GROUNDED
48
Grounding Instructions
WARNING - Improper grounding can
result in a risk of electric shock.
This appliance must be grounded. In
the event of an electrical short cir‐
cuit, grounding reduces the risk of
electric shock by providing a path of
least resistance.plug.
If there is any doubt, have the elec‐
trical system of the house checked
by a qualified electrician.
To increase security before the ma‐
chine is installed, it is recommended
to install a protective switch (30 mA).
 The hood must be hard wired ac‐
cordingly:
Black/Red wire: connect to L1 (live)
White wire: connect to N (neutral)
Green wire: connect to GND (ground)
Activating Con@ctivity 2.0
Installation of the Con@ctivity
2.0 stick
In order for you to be able to use the
Con@ctivity 2.0 function, the cooktop
must be equipped with a Con@ctivity
2.0 stick.
Activating the ventilation hood
 The cooktop and hood must be
turned off.
 Press the delayed shut down button
 for approx. 10 seconds until 1
lights up in the fan setting display.
 See the relevant installation instruc‐
tions of the Con@ctivity 2.0 stick.
 Next, tap the following buttons in
succession:
Activating the Con@ctivity 2.0
function
– The 1 button,
To use the Con@ctivity 2.0 function, the
radio link between the cooktop and the
ventilation hood must be activated.
– And then the lighting button .
Both appliances must be installed and
operational.
Wireless connection must be activated
on the ventilation hood and the cooktop
at the same time. Activation on the ven‐
tilation hood is described below.
Activation on the cooktop is described
in the relevant operating and installation
instructions. Please refer to the operat‐
ing instructions before starting.
Activate the ventilation hood first, then
the cooktop.
– Then the IS button,
The hood is in log on / log off mode.
If the wireless connection is already ac‐
tivated, 2 and 3 will light up at the same
time.
If there is no wireless connection, 2 and
3 will flash constantly (Con@ctivity 2.0
is already activated or a remote control
is logged on).
 To activate Con@ctivity 2.0, tap the
IS button.
The search for a wireless connection
will start.
 As this is happening, begin activation
on the cooktop.
49
Activating Con@ctivity 2.0
Activating the cooktop
Activation failed
 While the ventilation hood is search‐
ing for a wireless connection, start
activation on the cooktop.
More information can be found in the
operating instructions for the cook‐
top.
 If a wireless connection cannot be
established despite activation of the
Con@ctivity function on the ventila‐
tion hood and cooktop, the function
must first be deactivated and then re‐
activated on both appliances.
 When the cooktop registers that con‐
nection has been established, con‐
firm activation on the ventilation hood
with the delayed shut-down button
515. All indicators will go out.
Deactivating Con@ctivity 2.0
 Confirm activation on the cooktop.
 To deactivate the cooktop, please re‐
fer to the corresponding operating in‐
structions.
The Con@ctivity 2.0 function is now
ready for use.
If you do not confirm within 4 minutes,
activation will be canceled.
You only need to carry out the activa‐
tion procedure once. If the appliances
are disconnected from the electricity
supply, for example during a loss of
power, they will still remain activated.
50
 Deactivation on the ventilation hood
is similar to the activation procedure.
Select the IS instead of the 1 button.
Please keep in mind that disabling the
connection will also disable any re‐
mote control function being used. The
remote control must then be reactivat‐
ed.
Service and warranty
For faults that you cannot resolve on
your own, please contact your Miele
dealer or Miele Technical Service.
The telephone number for the Technical
Service Department is listed at the back
of these instructions.
When contacting Miele, please state
the model and serial number of your
ventilation hood.
These can be found on the data plate.
Location of the data plate
The data plate is visible once you have
removed the grease filters.
Warranty
For further information, please refer to
your warranty booklet.
51
Technical data
Fan motor
Overhead lighting
Total connected load
Voltage, Frequency
Fuse rating
Power cord length
Weight
350 W
4x3W
362 W
120 V AC, 60 Hz
15 A
6.5 ft. (2 m)
77 lbs (35 kg)
Optional accessories for recirculation mode:
Recirculation kit DUW 32 and OdorFree Charcoal Filter DKF 12
Contains
FCC ID: 2ACUWEI8800
IC: 5669C-EI8800
This device complies with Part 15 of the FCC Rules and with Industry Canada li‐
cence-exempt RSS standard(s). Operation is subject to the following two condi‐
tions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
52
Please have the model and serial number
of your appliance available before
contacting Technical Service.
U.S.A.
Canada
Miele, Inc.
Importer
Miele Limited
National Headquarters
9 Independence Way
Princeton, NJ 08540
Phone: 800-843-7231
609-419-9898
609-419-4298
Fax:
www.mieleusa.com
Technical Service & Support
Nationwide
Phone: 800-999-1360
888-586-8056
Fax:
TechnicalService@mieleusa.com
Headquarters and Miele Centre
161 Four Valley Drive
Vaughan, ON L4K 4V8
www.miele.ca
Customer Care Centre
Phone: 800-565-6435
905-532-2272
customercare@miele.ca
Germany
Manufacturer
Miele & Cie. KG
Carl-Miele-Straße 29
33332 Gütersloh
53
DA 6690 D

en-US
M.-Nr. 09 805 980 / 02