Samsung FE-R500WB User`s manual

SUPER
®
SC825 CHASSIS
Series
SC825TQ-R720LPB
SC825TQ-R740LPB
SC825TQ-710LP
SC825TQ-R720UB
SC825TQ-R740UB
SC825TQ-R740WB
SC825TQ-R700LP(V)(B)
SC825TQ-R700U(V)(B)
SC825TQ-600LPB
SC825TQ-563UB
SC835TQ-600WB
SC825TQ-563LPB
SC825TQ-560LP(V)(B)
SC825TQ-560U(V)(B)
SC825TQ-R500WB
USER’S MANUAL
2.0a
SC825 Chassis Manual
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 2.0a
Release Date: December 9, 2013
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2013 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
ii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SC825 2U chassis. Installation and maintenance should be performed by experienced technicians only.
Supermicro’s SC825 2U chassis features a unique and highly optimized design.
The chassis is equipped with a 560W (single), 563W (single) 600W (single), 700W
(redundant) 710W (single), 720W (redundant) or 740W (redundant) high-efficiency
power supply for superb power savings. High-performance fans provide ample
optimized cooling for the chassis.
This document lists compatible parts and configurations available when this document was published. Always refer to the our website for updates on supported
parts and configurations.
iii
SC825 Chassis Manual
Manual Organization
Chapter 1 Introduction
The first chapter provides a checklist of the main components included with this
chassis and describes the main features of the SC825 chassis. This chapter also
includes contact information.
Chapter 2 Standardized Warning Statements for AC Systems
This chapter lists warnings, precautions, and system safety. You should thoroughly
familiarize yourself with this chapter for a general overview of safety precautions
that should be followed before installing and servicing this chassis.
Chapter 3 Chassis Components
Refer here for details on this chassis model including the fans, bays, airflow shields,
and other components.
Chapter 4 System Interface
Refer to this chapter for details on the system interface, which includes the functions
and information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 5 Chassis Setup and Maintenance
Refer to this chapter for detailed information on this chassis. You should follow the
procedures given in this chapter when installing, removing, or reconfiguring your
chassis.
Chapter 6 Rack Installation
Refer to this chapter for detailed information on chassis rack installation. You should
follow the procedures given in this chapter when installing, removing or reconfiguring
your chassis into a rack environment.
iv
Preface
Appendices
This section lists compatible cables, power supply specifications, and compatible
backplanes. Not all compatible backplanes may be listed. Refer to our website for
the latest compatible backplane information.
v
SC825 Chassis Manual
Table of Contents
Chapter 1 Introduction
1-1Overview.......................................................................................................... 1-1
1-2
Shipping List..................................................................................................... 1-1
1-3
Chassis Features............................................................................................. 1-2
CPU.................................................................................................................. 1-2
Hard Drives...................................................................................................... 1-2
I/O Expansion slots.......................................................................................... 1-2
Peripheral Drives.............................................................................................. 1-2
Other Features................................................................................................. 1-2
SCSI Chassis Models...................................................................................... 1-2
1-4
Contacting Supermicro..................................................................................... 1-3
1-5
Returning Merchandise for Service................................................................. 1-4
Chapter 2 Standardized Warning Statements for AC Systems
2-1
About Standardized Warning Statements........................................................ 2-1
Warning Definition............................................................................................ 2-1
Installation Instructions..................................................................................... 2-4
Circuit Breaker................................................................................................. 2-5
Power Disconnection Warning......................................................................... 2-6
Equipment Installation...................................................................................... 2-8
Restricted Area................................................................................................. 2-9
Battery Handling............................................................................................. 2-10
Redundant Power Supplies........................................................................... 2-12
Backplane Voltage......................................................................................... 2-13
Comply with Local and National Electrical Codes......................................... 2-14
Product Disposal............................................................................................ 2-15
Hot Swap Fan Warning.................................................................................. 2-16
Power Cable and AC Adapter ....................................................................... 2-18
Chapter 3 Chassis Components
3-1Overview.......................................................................................................... 3-1
3-2Components..................................................................................................... 3-1
Chassis............................................................................................................. 3-1
Backplane......................................................................................................... 3-1
Fans................................................................................................................. 3-1
Mounting Rails................................................................................................. 3-1
Power Supply................................................................................................... 3-2
vi
Preface
Air Shroud........................................................................................................ 3-2
3-3
Where to get Replacement Components......................................................... 3-2
Chapter 4 System Interface
4-1Overview.......................................................................................................... 4-1
4-2
Control Panel Buttons...................................................................................... 4-2
4-3
Control Panel LEDs......................................................................................... 4-2
4-4
Drive Carrier LEDs........................................................................................... 4-4
SAS/SATA Drives............................................................................................. 4-4
Chapter 5 Chassis Setup and Maintenance
5-1Overview.......................................................................................................... 5-1
5-2
Installation and General Maintnenance........................................................... 5-1
Installation........................................................................................................ 5-1
5-3
Removing the Chassis Cover.......................................................................... 5-2
5-4
Installing Hard Drives....................................................................................... 5-3
5-5
Installing an Optional Floppy or Fixed Hard Drive........................................... 5-6
5-6
DVD-ROM Replacement or Installation........................................................... 5-7
Replacing the DVD-ROM and Front Panel...................................................... 5-7
5-7
Installing the Motherboard............................................................................... 5-8
I/O Shield......................................................................................................... 5-8
Installing the I/O Shield.................................................................................... 5-8
Permanent and Optional Standoffs.................................................................. 5-9
Add-on Card/Expansion Slot Setup................................................................5-11
Add-on Card/Expansion Slot Setup in LP (Low Profile) Chassis...................5-11
Add-on Card/Expansion Slot Setup for SC825U (Universal Output) and
SC825W......................................................................................................... 5-12
5-8
Installing the Air Shroud................................................................................. 5-13
Checking the Server's Air Flow...................................................................... 5-14
Installation Complete...................................................................................... 5-14
5-9
System Fans.................................................................................................. 5-15
5-10 Power Supply ................................................................................................ 5-17
Power Supply Failure..................................................................................... 5-17
Replacing the Power Distributor.................................................................... 5-19
Replacing or Installing the Front Port Panel.................................................. 5-20
5-11 Optional Front Bezel...................................................................................... 5-21
Chapter 6 Rack Installation
6-1Overview.......................................................................................................... 6-1
6-2
Unpacking the System..................................................................................... 6-1
6-3
Preparing for Setup.......................................................................................... 6-1
vii
SC825 Chassis Manual
Choosing a Setup Location.............................................................................. 6-1
Rack Precautions............................................................................................. 6-2
General Server Precautions............................................................................. 6-2
Rack Mounting Considerations........................................................................ 6-3
Ambient Operating Temperature................................................................. 6-3
Reduced Airflow.......................................................................................... 6-3
Mechanical Loading.................................................................................... 6-3
Circuit Overloading...................................................................................... 6-3
Reliable Ground.......................................................................................... 6-3
6-4
Rack Mounting Instructions.............................................................................. 6-4
Separating the Sections of the Rack Rails...................................................... 6-4
Installing the Inner Rail Extension................................................................... 6-5
Outer Rack Rails.............................................................................................. 6-6
Appendix A SC825 Chassis Cables
Appendix B SC825 Power Supply Specifications
Appendix C BPN-SAS-825TQ Backplane Specifications
viii
Chapter 1: Introduction
Chapter 1
Introduction
1-1Overview
Supermicro’s SC825 2U chassis features a unique and highly-optimized design.
The chassis is equipped with high efficiency power supply.
1-2 Shipping List
Please visit the following link for the latest shipping lists and part numbers for your
particular chassis model www.supermicro.com
SC825 Chassis
Model
HDD
I/O Slots
Power Supply
SC825TQ-R740WB
8x SAS / SATA
4x FF 3x LP
740W (Platnum Level
Redundant)
SC825TQ-R740UB
8x SAS / SATA
4x FH 3x LP
740W (Platnum Level
Redundant)
SC825TQ-R740LPB
8x SAS / SATA
7x LF
740W (Platnum Level
Redundant)
8x SAS/SATA
7x LF
720W (Gold Level)
SC825TQ-720UB
8x SAS/SATA
4x FF 3x LP
720W (Gold Level)
SC825TQ-710LP
8x SAS/ SATA
7x LP, FL
710W
SC825TQ-R700UV /
SC825TQ-R700UB
8x SAS/SATA
4x FF 3x LP
700W Redundant
SC825TQ-R700LPV /
SC825TQ-R700LPB
8x SAS/SATA
7x LP
700W Redundant
SC825TQ-600WB
8x SAS/SATA
8x SAS/SATA
600W (Platinum Level)
SC825TQ-600LPB
SC825TQ-720LPB
8x SAS/SATA
7x LF
600W
SC825TQ-563LPB
/ SC825TQ-563UB
8x SAS/SATA
7x LF / 3x FF, 3
LP, 1 UIO
560W
SC825TQ-560UV /
SC825TQ-560UB
8x SAS/SATA
4x FF 3x LP
560W
SC825TQ-560LPV /
SC825TQ-560LPB
8x SAS/SATA
7x LP
560W
SC825TQ-R500WB
8x SAS/SATA
4x FF 3x LP
500W (Platinum Level
Redundant)
Legend: FF: Full-height, full length, FH: Full-height, half length. LF: Low-profile,
full-length. LP: Low-profile.
1-1
SC825 Chassis Manual
1-3 Chassis Features
The SC825 2U, high-performance chassis includes the following features:
CPU
The SC825 chassis supports single or dual processors. Please refer to the motherboard specifications pages on our web site for updates on supported processors.
Hard Drives
The SC825 chassis features eigh slots for SAS/SATA drives. These drives are
hot-swappable. Once set up correctly, these drives can be removed without powering down the server. In addition, these drives support SES2 (SAS/SATA).
I/O Expansion slots
Each SC825 chassis model includes seven low-profile I/O expansion slots.
Peripheral Drives
Each SC825 chassis supports one slim DVD-ROM drive (included) and one slim
floppy drive (optional). These drives allow you to quickly install or save data.
Other Features
Other onboard features are included to promote system health. These include
various three cooling fans, a convenient power switch, reset button, and five LED
indicators.
1-2
Chapter 1: Introduction
1-4 Contacting Supermicro
Headquarters
Address:
Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel:
+1 (408) 503-8000
Fax:
+1 (408) 503-8008
Email:
marketing@supermicro.com (General Information)
support@supermicro.com (Technical Support)
Website:
www.supermicro.com
Europe
Address:
Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel:
+31 (0) 73-6400390
Fax:
+31 (0) 73-6416525
Email:
sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
rma@supermicro.nl (Customer Support)
Website:
www.supermicro.nl
Asia-Pacific
Address:
Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel:
+886-(2) 8226-3990
Fax:
+886-(2) 8226-3992
Email:
support@supermicro.com.tw
Website:
www.supermicro.com.tw
1-3
SC825 Chassis Manual
1-5 Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required before any warranty service will be rendered. You can obtain service by calling your
vendor for a Returned Merchandise Authorization (RMA) number. When returning to
the manufacturer, the RMA number should be prominently displayed on the outside
of the shipping carton, and mailed prepaid or hand-carried. Shipping and handling
charges will be applied for all orders that must be mailed when service is complete.
For faster service, RMA authorizations may be requested online (http://www.
supermicro.com/support/rma/).
Whenever possible, repack the chassis in the original Supermicro carton, using the
original packaging material. If these are no longer available, be sure to pack the
chassis securely, using packaging material to surround the chassis so that it does
not shift within the carton and become damaged during shipping.
This warranty only covers normal consumer use and does not cover damages incurred in shipping or from failure due to the alteration, misuse, abuse or improper
maintenance of products.
During the warranty period, contact your distributor first for any product problems.
1-4
Chapter 2: Warning Statements for AC Systems
Chapter 2
Standardized Warning Statements for AC Systems
2-1 About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certified technicians should attempt to install or configure
components.
Read this appendix in its entirety before installing or configuring components in the
Supermicro chassis.
These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.
Warning Definition
Warning!
This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.
警告の定義
この警告サインは危険を意味します。
人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、
電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。
此警告符号代表危险。
您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前,必须充分
意识到触电的危险,并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。
此警告符號代表危險。
您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前,請注意觸
電的危險,並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容。
2-1
SC825 Chassis Manual
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu
Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes
de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
final de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.
GUARDE ESTAS INSTRUCCIONES.
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une
situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS.
‫תקנון הצהרות אזהרה‬
‫ על מנת להזהיר את המשתמש מפני חבלה‬,‫הצהרות הבאות הן אזהרות על פי תקני התעשייה‬
‫ יש ליצור קשר עם מחלקת תמיכה‬,‫ במידה ויש שאלות או היתקלות בבעיה כלשהי‬.‫פיזית אפשרית‬
.‫ טכנאים מוסמכים בלבד רשאים להתקין או להגדיר את הרכיבים‬.‫טכנית של סופרמיקרו‬
.‫יש לקרוא את הנספח במלואו לפני התקנת או הגדרת הרכיבים במארזי סופרמיקרו‬
2-2
Warning Statements for AC Systems
. ‫تحذٌز!هذا الزهز ٌعًٌ خطز اًك فً حالة ٌوكي أى تتسبب فً اصابة جسذٌة‬
‫كي على علن بالوخاطز الٌاجوة عي الذوائز‬،‫قبل أى تعول على أي هعذات‬
‫الكهزبائٍة‬
‫وكي على دراٌة بالووارسات الىقائٍة لوٌع وقىع أي حىادث‬
‫استخذم رقن البٍاى الوٌصىص فً ًهاٌة كل تحذٌز للعثىر تزجوتها‬
안전을 위한 주의사항
경고!
이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준
작업절차를 준수해 주시기 바랍니다.
해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.
BEWAAR DEZE INSTRUCTIES
2-3
SC825 Chassis Manual
Installation Instructions
Warning!
Read the installation instructions before connecting the system to the power source.
設置手順書
システムを電源に接続する前に、設置手順書をお読み下さい。
警告
将此系统连接电源前,请先阅读安装说明。
警告
將系統與電源連接前,請先閱讀安裝說明。
Warnung
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen
lesen.
¡Advertencia!
Lea las instrucciones de instalación antes de conectar el sistema a la red de
alimentación.
Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives
d'installation.
.‫יש לקרוא את הוראות התקנה לפני חיבור המערכת למקור מתח‬
‫اقر إرشادات التركيب قبل توصيل النظام إلى مصدر للطاقة‬
시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.
Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron
aansluit.
2-4
Chapter 2: Warning Statements for AC Systems
Circuit Breaker
Warning!
This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.
サーキット・ブレーカー
この製品は、短絡(過電流)保護装置がある建物での設置を前提としています。
保護装置の定格が250 V、20 Aを超えないことを確認下さい。
警告
此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电
流不大于250V,20A。
警告
此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電
流不大於250V,20A。
Warnung
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschlussbzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der
Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.
¡Advertencia!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)
del edificio. Asegúrese de que el dispositivo de protección no sea superior a: 250
V, 20 A.
Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit
dépend de l'installation électrique du local. Vérifiez que le courant nominal du
dispositif de protection n'est pas supérieur à :250 V, 20 A.
‫ יש לוודא כי‬.‫מוצר זה מסתמך על הגנה המותקנת במבנים למניעת קצר חשמלי‬
250 V, 20 A-‫המכשיר המגן מפני הקצר החשמלי הוא לא יותר מ‬
‫هذا المنتج يعتمد على معداث الحمايت مه الدوائرالقصيرة التي تم تثبيتها في‬
‫المبنى‬
20A, 250V :‫تأكد من أن تقييم الجهاز الوقائي ليس أكثر من‬
2-5
SC825 Chassis Manual
경고!
이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에
의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지
않도록 해야 합니다.
Waarschuwing
Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van
uw electrische installatie. Controleer of het beveiligde aparaat niet groter
gedimensioneerd is dan 220V, 20A.
Power Disconnection Warning
Warning!
The system must be disconnected from all sources of power and the power cord
removed from the power supply module(s) before accessing the chassis interior to
install or remove system components.
電源切断の警告
システムコンポーネントの取り付けまたは取り外しのために、
シャーシー内部にアクセス
するには、
システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り
外す必要があります。
警告
在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。
警告
在您打開機殼安裝或移除內部元件前,必須將系統完全斷電,並移除電源線。
Warnung
Das System muss von allen Quellen der Energie und vom Netzanschlusskabel
getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es
auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder
zu entfernen.
2-6
Chapter 2: Warning Statements for AC Systems
¡Advertencia!
El sistema debe ser disconnected de todas las fuentes de energía y del cable
eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso
el interior del chasis para instalar o para quitar componentes de sistema.
Attention
Le système doit être débranché de toutes les sources de puissance ainsi que de
son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour
installer ou enlever des composants de systéme.
‫אזהרה מפני ניתוק חשמלי‬
!‫אזהרה‬
‫יש לנתק את המערכת מכל מקורות החשמל ויש להסיר את כבל החשמלי מהספק‬
.‫לפני גישה לחלק הפנימי של המארז לצורך התקנת או הסרת רכיבים‬
‫يجب فصم اننظاو من جميع مصادر انطاقت وإزانت سهك انكهرباء من وحدة امداد‬
‫انطاقت قبم‬
‫انىصىل إنى انمناطق انداخهيت نههيكم نتثبيج أو إزانت مكىناث الجهاز‬
경고!
시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에
반드시 전원 공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야
합니다.
Waarschuwing
Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren
of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle
stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen
2-7
SC825 Chassis Manual
Equipment Installation
Warning!
Only trained and qualified personnel should be allowed to install, replace, or service
this equipment.
機器の設置
トレーニングを受け認定された人だけがこの装置の設置、交換、
またはサービスを許可
されています。
警告
只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。
警告
只有經過受訓且具資格人員才可安裝、更換與維修此設備。
Warnung
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,
qualifiziertem Personal gestattet werden.
¡Advertencia!
Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.
Attention
Il est vivement recommandé de confier l'installation, le remplacement et la
maintenance de ces équipements à des personnels qualifiés et expérimentés.
!‫אזהרה‬
.‫ להחליף את הציוד או לתת שירות עבור הציוד‬,‫צוות מוסמך בלבד רשאי להתקין‬
‫يجب أن يسمح فقط للمىظفيه المؤهليه والمدربيه لتزكيب واستبدال أو خدمة هذا الجهاس‬
경고!
훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수
있습니다.
2-8
Chapter 2: Warning Statements for AC Systems
Waarschuwing
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door
geschoold en gekwalificeerd personeel.
Restricted Area
Warning!
This unit is intended for installation in restricted access areas. A restricted access
area can be accessed only through the use of a special tool, lock and key, or other
means of security. (This warning does not apply to workstations).
アクセス制限区域
このユニットは、
アクセス制限区域に設置されることを想定しています。
アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いての
み出入りが可能です。
警告
此部件应安装在限制进出的场所,限制进出的场所指只能通过使用特殊工具、锁和
钥匙或其它安全手段进出的场所。
警告
此裝置僅限安裝於進出管制區域,進出管制區域係指僅能以特殊工具、鎖頭及鑰匙
或其他安全方式才能進入的區域。
Warnung
Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.
Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und
Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.
¡Advertencia!
Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.
Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una
herramienta especial, cerradura con llave u otro medio de seguridad.
Attention
Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une
zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme
de verrouillage et une clé, ou tout autre moyen de sécurité.
2-9
SC825 Chassis Manual
‫אזור עם גישה מוגבלת‬
!‫אזהרה‬
‫ הגישה ניתנת בעזרת‬.‫יש להתקין את היחידה באזורים שיש בהם הגבלת גישה‬
.)'‫ מנעול וכד‬,‫כלי אבטחה בלבד (מפתח‬
. ‫تم تخصيص هذه انىحذة نتركُبها فٍ مناطق محظورة‬
،‫َمكن انىصىل إنً منطقت محظورة فقط من خالل استخذاو أداة خاصت‬
‫قفم ومفتاح أو أٌ وسُهت أخري نالمألما‬
경고!
이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및
키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.
Waarschuwing
Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.
Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te
maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.
Battery Handling
Warning!
There is the danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー
カーが推奨する型、
または同等のものを使用下さい。使用済電池は製造元の指示に従
って処分して下さい。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。
2-10
Chapter 2: Warning Statements for AC Systems
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer
que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.
¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta.
Reemplazar la batería exclusivamente con el mismo tipo o el equivalente
recomendado por el fabricante. Desechar las baterías gastadas según las
instrucciones del fabricante.
!‫אזהרה‬
‫ יש להחליף‬.‫קיימת סכנת פיצוץ של הסוללה במידה והוחלפה בדרך לא תקינה‬
.‫את הסוללה בסוג התואם מחברת יצרן מומלצת‬
.‫סילוק הסוללות המשומשות יש לבצע לפי הוראות היצרן‬
‫هناك خطر من انفجار في حالة اسحبذال البطارية بطريقة غير صحيحة فعليل‬
‫اسحبذال البطارية‬
‫فقط بنفس النىع أو ما يعادلها مما أوصث به الشرمة المصنعة‬
‫جخلص من البطاريات المسحعملة وفقا لحعليمات الشرمة الصانعة‬
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와
동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.
제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Waarschuwing
Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt. Vervang de
batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen
wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd
te worden.
2-11
SC825 Chassis Manual
Redundant Power Supplies
Warning!
This unit might have more than one power supply connection. All connections must
be removed to de-energize the unit.
冗長電源装置
このユニットは複数の電源装置が接続されている場合があります。
ユニットの電源を切るためには、すべての接続を取り外さなければなりません。
警告
此部件连接的电源可能不止一个,必须将所有电源断开才能停止给该部件供电。
警告
此裝置連接的電源可能不只一個,必須切斷所有電源才能停止對該裝置的供電。
Warnung
Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass
der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.
¡Advertencia!
Puede que esta unidad tenga más de una conexión para fuentes de alimentación.
Para cortar por completo el suministro de energía, deben desconectarse todas las
conexiones.
Attention
Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute
tension et tout courant électrique de l'unité, toutes les connexions d'alimentation
doivent être débranchées.
‫אם קיים יותר מספק אחד‬
!‫אזהרה‬
‫ יש להסיר את כל החיבורים על מנת לרוקן‬.‫ליחדה יש יותר מחיבור אחד של ספק‬
.‫את היחידה‬
2-12
Chapter 2: Warning Statements for AC Systems
경고!
.‫قد يكون لهذا الجهاز عدة اتصاالت بوحدات امداد الطاقة‬
‫يجب إزالة كافة االتصاالت لعسل الوحدة عن الكهرباء‬
이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에
전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.
Waarschuwing
Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle
aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.
Backplane Voltage
Warning!
Hazardous voltage or energy is present on the backplane when the system is
operating. Use caution when servicing.
バックプレーンの電圧
システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。
修理する際には注意ください。
警告
当系统正在进行时,背板上有很危险的电压或能量,进行维修时务必小心。
警告
當系統正在進行時,背板上有危險的電壓或能量,進行維修時務必小心。
Warnung
Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche
Spannungen oder Energien auf. Vorsicht bei der Wartung.
¡Advertencia!
Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.
Tenga cuidado cuando lo revise.
Attention
Lorsque le système est en fonctionnement, des tensions électriques circulent sur
le fond de panier. Prendre des précautions lors de la maintenance.
2-13
SC825 Chassis Manual
‫מתח בפנל האחורי‬
!‫אזהרה‬
‫ יש להיזהר במהלך‬.‫קיימת סכנת מתח בפנל האחורי בזמן תפעול המערכת‬
.‫העבודה‬
‫هناك خطز مه التيار الكهزبائي أوالطاقة المىجىدة على اللىحة‬
‫عندما يكىن النظام يعمل كه حذرا عند خدمة هذا الجهاس‬
경고!
시스템이 동작 중일 때 후면판 (Backplane)에는 위험한 전압이나 에너지가 발생
합니다. 서비스 작업 시 주의하십시오.
Waarschuwing
Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het
systeem in gebruik is. Voorzichtigheid is geboden tijdens het onderhoud.
Comply with Local and National Electrical Codes
Warning!
Installation of the equipment must comply with local and national electrical codes.
地方および国の電気規格に準拠
機器の取り付けはその地方および国の電気規格に準拠する必要があります。
警告
设备安装必须符合本地与本国电气法规。
警告
設備安裝必須符合本地與本國電氣法規。
Warnung
Die Installation der Geräte muss den Sicherheitsstandards entsprechen.
¡Advertencia!
La instalacion del equipo debe cumplir con las normas de electricidad locales y
nacionales.
2-14
Chapter 2: Warning Statements for AC Systems
Attention
L'équipement doit être installé conformément aux normes électriques nationales
et locales.
‫תיאום חוקי החשמל הארצי‬
!‫אזהרה‬
.‫התקנת הציוד חייבת להיות תואמת לחוקי החשמל המקומיים והארציים‬
‫تركيب المعدات الكهربائية يجب أن يمتثل للقىاويه المحلية والىطىية المتعلقة‬
‫بالكهرباء‬
경고!
현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.
Waarschuwing
Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale
elektriciteitsvoorschriften.
Product Disposal
Warning!
Ultimate disposal of this product should be handled according to all national laws
and regulations.
製品の廃棄
この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
あります。
警告
本产品的废弃处理应根据所有国家的法律和规章进行。
警告
本產品的廢棄處理應根據所有國家的法律和規章進行。
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen
des Landes erfolgen.
2-15
SC825 Chassis Manual
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y
reglamentos nacionales.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des
lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.
‫סילוק המוצר‬
!‫אזהרה‬
.‫סילוק סופי של מוצר זה חייב להיות בהתאם להנחיות וחוקי המדינה‬
‫عند التخلص النهائي من هذا المنتج ينبغي التعامل معه وفقا لجميع القىانين واللىائح الىطنية‬
경고!
이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming
met alle nationale wetten en reglementen.
Hot Swap Fan Warning
Warning!
The fans might still be turning when you remove the fan assembly from the chassis.
Keep fingers, screwdrivers, and other objects away from the openings in the fan
assembly's housing.
ファン・ホットスワップの警告
シャーシから冷却ファン装置を取り外した際、
ファンがまだ回転している可能性がありま
す。ファンの開口部に、指、
ドライバー、およびその他のものを近づけないで下さい。
警告
当您从机架移除风扇装置,风扇可能仍在转动。小心不要将手指、螺丝起子和其他
物品太靠近风扇
2-16
Chapter 2: Warning Statements for AC Systems
警告
當您從機架移除風扇裝置,風扇可能仍在轉動。小心不要將手指、螺絲起子和其他
物品太靠近風扇。
Warnung
Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis
genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände
von den Öffnungen des Lüftergehäuses entfernt.
¡Advertencia!
Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador
del chasis. Mandtenga los dedos, los destornilladores y todos los objetos lejos de
las aberturas del ventilador
Attention
Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez
le bloc ventilateur du châssis. Prenez garde à ce que doigts, tournevis et autres
objets soient éloignés du logement du bloc ventilateur.
!‫אזהרה‬
‫ יש‬.‫ יתכן והמאווררים עדיין עובדים‬,‫כאשר מסירים את חלקי המאוורר מהמארז‬
‫להרחיק למרחק בטוח את האצבעות וכלי עבודה שונים מהפתחים בתוך המאוורר‬
‫مه انممكه أن انمراوح ال تسال تدورعند إزانة كتهة انمروحة مه انهيكم يجب إبقاء‬
‫األصابع ومفكات انبراغي‬
.‫وغيرها مه األشياء بعيدا عه انفتحات في كتهة انمروحة‬
경고!
섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬
조림품 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버, 다른 물체들이
가까이 하지 않도록 배치해 주십시오.
Waarschuwing
Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het
ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers
en eventuele andere voorwerpen uit de buurt van de openingen in de
ventilatorbehuizing.
2-17
SC825 Chassis Manual
Power Cable and AC Adapter
Warning!
When installing the product, use the provided or designated connection cables,
power cables and AC adaptors. Using any other cables and adaptors could cause
a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the
use of UL or CSA -certified cables (that have UL/CSA shown on the code) for any
other electrical devices than products designated by Supermicro only.
電源コードとACアダプター
製品を設置する場合、提供または指定された接続ケーブル、電源コードとACアダプター
を使用下さい。他のケーブルやアダプタを使用すると故障や火災の原因になることがあ
ります。電気用品安全法は、ULまたはCSA認定のケーブル(UL/CSEマークがコードに表
記)を Supermicroが指定する製品以外に使用することを禁止しています。
警告
安装此产品时,请使用本身提供的或指定的连接线,电源线和电源适配器.使用其它线
材或适配器可能会引起故障或火灾。除了Supermicro所指定的产品,电气用品和材
料安全法律规定禁止使用未经UL或CSA认证的线材。(线材上会显示UL/CSA符号)。
警告
安裝此產品時,請使用本身提供的或指定的連接線,電源線和電源適配器.使用其它線
材或適配器可能會引起故障或火災。除了Supermicro所指定的產品,電氣用品和材
料安全法律規定禁止使用未經UL或CSA認證的線材。(線材上會顯示UL/CSA符號)。
Warnung
Bei der Installation des Produkts, die zur Verfügung gestellten oder benannt
Anschlusskabel, Stromkabel und Netzteile. Verwendung anderer Kabel und Adapter
kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Geräte und
Material Safety Law verbietet die Verwendung von UL-oder CSA-zertifizierte Kabel,
UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von
Supermicro nur bezeichnet gezeigt haben.
¡Advertencia!
Al instalar el producto, utilice los cables de conexión previstos o designados, los
cables y adaptadores de CA. La utilización de otros cables y adaptadores podría
ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de
Seguridad del Material prohíbe el uso de UL o CSA cables certificados que tienen
UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos
designados por Supermicro solamente.
2-18
Chapter 2: Warning Statements for AC Systems
Attention
Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné.
L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement
ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit
l'utilisation de UL ou CSA câbles certifiés qui ont UL ou CSA indiqué sur le code
pour tous les autres appareils électriques que les produits désignés par Supermicro
seulement.
AC
‫חשמליים ומתאמי‬
!‫אזהרה‬
‫ אשר‬AC ‫ ספקים ומתאמים‬,‫ יש להשתמש בכבלים‬,‫כאשר מתקינים את המוצר‬
‫ שימוש בכל כבל או מתאם אחר יכול לגרום לתקלה או‬.‫נועדו וסופקו לשם כך‬
‫ קיים איסור‬,‫ על פי חוקי שימוש במכשירי חשמל וחוקי בטיחות‬.‫קצר חשמלי‬
‫ (כשאר מופיע עליהם קוד של‬CSA -‫ או ב‬UL -‫להשתמש בכבלים המוסמכים ב‬
.‫) עבור כל מוצר חשמלי אחר שלא צוין על ידי סופרקמיקרו בלבד‬UL/CSA
‫والكابالث الكهربائيت‬،‫عىذ تركيب الجهاز يجب استخذام كابالث التىصيل‬
‫ومحىالث التيار المتردد‬
.‫ أن استخذام أي كابالث ومحىالث أخري يتسبب في حذوث عطل أو حريق‬. ‫التي‬
‫تم تىفيرها لك مع المىتج‬
UL ‫ أو‬CSA ‫األجهسة الكهربائيت ومىاد قاوىن السالمت يحظر استخذام الكابالث‬
‫معتمذة مه قبل‬
Supermicro ‫ألي أجهسة كهربائيت أخري غير المىتجاث المعيىت مه قبل‬
(UL/CSA ‫)التي تحمل عالمت‬
경고!
제품을 설치할 때에는 제공되거나 지정된 연결케이블과 전원케이블, AC어댑터를
사용해야 합니다. 그 밖의 다른 케이블들이나 어댑터들은 고장 또는 화재의 원인이
될 수 있습니다. 전기용품안전법 (Electrical Appliance and Material Safety
Law)은 슈퍼마이크로에서 지정한 제품들 외에는 그 밖의 다른 전기 장치들을
위한 UL또는 CSA에서 인증한 케이블(전선 위에 UL/CSA가 표시)들의 사용을
금지합니다.
Waarschuwing
Bij het installeren van het product, gebruik de meegeleverde of aangewezen kabels,
stroomkabels en adapters. Het gebruik van andere kabels en adapters kan leiden
tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet
verbiedt het gebruik van UL of CSA gecertificeerde kabels die UL of CSA die op
de code voor andere elektrische apparaten dan de producten die door Supermicro
alleen.
2-19
SC825 Chassis Manual
Notes
2-20
Chapter 3: Chassis Components
Chapter 3
Chassis Components
3-1Overview
This chapter describes the most common components included with your chassis.
Some components listed may not be included or may not be compatible with your
particular chassis model. For more information, see the installation instructions
detailed later in this manual.
3-2Components
Chassis
The SC825 chassis includes eight hard drive bays. Most chassis models come with
a DVD-ROM. Hard drives must be purchased separately. For the latest shipping
lists, visit our website at: www.supermicro.com.
This chassis supports a 2U backplane, three fans and one or two power supplies.
SC825 models come in silver or black.
Backplane
Each SC825 chassis comes with a 2U SAS/SATA backplane. For more information
regarding compatible backplanes, view the appendices found at the end of this manual. In addition, visit our website for the latest information at www.supermicro.com.
Fans
The SC825 chassis supports three system fans. System fans for SC825 chassis
are powered from the motherboard. These fans are 2U high and are powered by
3-pin connectors.
Mounting Rails
The SC825 can be placed in a rack for secure storage and use. To setup your rack,
follow the step-by-step instructions included in this manual.
3-1
SC825 Chassis Manual
Power Supply
Each SC825 chassis model includes a high-efficiency power supply rated at 500W
(redundant), 560W (single), 563W (single) 600W (single), 700W (redundant) 710W
(single), 720W (redundant) or 740W (Redundant). In the unlikely event your power
supply fails, replacement is simple and can be accomplished without tools.
Air Shroud
Air shrouds are shields, usually plastic, which conduct the airflow directly to where
it is needed. Always use the air shroud included with your chassis.
3-3 Where to get Replacement Components
Although not frequently, you may need replacement parts for your system. To ensure
the highest level of professional service and technical support, we strongly recommend purchasing exclusively from our Supermicro Authorized Distributors/ System
Integrators/Resellers. A list of Supermicro Authorized Distributors/System Integrators/Reseller can be found at: www.supermicro.com. Click the Where to Buy link.
3-2
Chapter 4: System Interface
Chapter 4
System Interface
4-1Overview
There are LEDs on the control panel and the drive carriers to keep you constantly
informed of the over-all status of the system, as well as the activity and health of
specific components. Most SC825 models have two buttons on the chassis control
panel: a reset button and an on/off switch. This chapter explains the meanings of
all LED indicators and the appropriate response you may need to take.
Figure 4-1: Control Panel LEDs
4-1
SC825 Chassis Manual
4-2 Control Panel Buttons
There are two push-buttons located on the front of the chassis. These are (in order
from left to right) a reset button and a power on/off button.
•Reset: The reset button is used to reboot the system.
•Power: The main power switch is used to apply or remove power from the
power supply to the server system. Turning off system power with this button
removes the main power but keeps standby power supplied to the system.
Therefore, you must unplug system before servicing.
4-3 Control Panel LEDs
The control panel located on the front of the SC825 chassis has five LEDs. These
LEDs provide you with critical information related to different parts of the system.
This section explains what each LED indicates when illuminated and any corrective action you may need to take.
!
•Power Failure: When this LED flashes, it indicates a power failure in the power
supply.
•Information LED: See the following table for the status shown by this LED.
4-2
Chapter 4: System Interface
Information LED
Status
Description
Continously on and red
An overheat ocondition has occured. (This may be
caused by cable congestion.)
Blinking red (1 Hz)
Fan failure: check for an inoperative fan.
Blinking red (0.25 Hz)
Power failure: check for an inoperative power supply.
Solid blue
Local UID has been activated. Use this function to
locate the server in a rack environment.
Blinking blue (300 msec)
Remote UID has been activated. Use this function to
locate the server from a remote location.
2
•NIC2: Indicates network activity on GLAN2 when flashing.
1
•NIC1: Indicates network activity on GLAN1 when flashing.
•HDD: Indicates IDE channel activity in the SAS/SATA drive, SCSI drive, and/
or DVD-ROM drive activity when flashing.
•Power: Indicates power is being supplied to the system's power supply units.
This LED should normally be illuminated when the system is operating.
4-3
SC825 Chassis Manual
4-4 Drive Carrier LEDs
Your chassis uses SAS/SATA drives.
SAS/SATA Drives
Each SAS/SATA drive carrier has two LEDs.
Green: Each Serial ATA drive carrier has a green LED. When illuminated, this
green LED (on the front of the SATA drive carrier) indicates drive activity. A connection to the SATA backplane enables this LED to blink on and off when that
particular drive is being accessed.
Red: The red LED indicates a SAS/SATA drive failure. If one of the SAS/SATA drives
fail, you should be notified by your system management software.
4-4
Chapter 5: Chassis Setup and Maintenance
Chapter 5
Chassis Setup and Maintenance
5-1Overview
This chapter covers the steps required to install components and perform maintenance on the chassis. The only tool you will need to install components and perform
maintenance is a Phillips screwdriver. Print this page to use as a reference while
setting up your chassis.
5-2 Installation and General Maintnenance
Installation
•Removing the Chassis Cover
•Installing Hard Drives
•Installing an Optional Fixed Hard Drive
•DVD ROM Replacement or Installation
•Installing the Motherboard (includes I/O Slot Setup)
•Installing the Air Shroud
General Maintenance
•System Fans
•Replacing the Power Supply
•Optional Front Bezel
Review the warnings and precautions listed in the manual before setting up or servicing
this chassis. These include information in Chapter 2: Standardized Warning Statements
for and the warning/precautions listed in the setup instructions.
5-1
SC825 Chassis Manual
5-3 Removing the Chassis Cover
4
1
Remove
Screw
2
3
2
1
Remove
Screw
Release Tab
Figure 5-1: Removing the Chassis Cover
Removing the Chassis Cover
1. Disconnect the power supply, lay the chassis on a flat surface.
2. Remove the two screws on each side of the cover, which secure the cover to
the chassis.
3. Press the release tabs to remove the cover from the locked position. Press
both tabs at the same time.
4. Once the top cover is released from the locked position, slide the cover
toward the rear of the chassis.
5. Lift the cover off the chassis.
Warning: Except for short periods of time, do NOT operate the server without the
cover in place. The chassis cover must be in place to allow proper airflow and prevent
overheating.
5-2
Chapter 5: Chassis Setup and Maintenance
5-4 Installing Hard Drives
2
1
Figure 5-2: Removing Hard Drive
The SC825 features hot-swappable hard drives which can be removed without
powering down the system.
Removing Hard Drive Trays from the Chassis
1. Press the release button on the drive carrier. This extends the drive carrier
handle.
2. Use the handle to pull the drive out of the chassis.
5-3
SC825 Chassis Manual
Dummy Drive
Drive Carrier
Figure 5-3: Chassis Drive Carrier
The drives are mounted in drive carriers to simplify their installation and removal
from the chassis. These carriers also help promote proper airflow for the drive
bays.
1
1
Figure 5-4: Removing Dummy Drive from Carrier
Installing a Hard Drive to the Hard Drive Carrier
1. Remove the screws securing the dummy drive to the carrier.
2. Remove the dummy drive from the carrier.
Warning: Except for short periods of time (swapping hard drives), do not operate the
server with the hard drives removed from the bays.
5-4
Chapter 5: Chassis Setup and Maintenance
SAS/SATA
Hard Drive
4
4
Drive Carrier
Figure 5-5: Removing the Hard Drive
3. Install a new drive into the carrier with the printed circuit board side facing
down so that the mounting holes align with those in the carrier.
4. Secure the hard drive by tightening all six screws.
5. Replace the drive carrier into the chassis bay, making sure that the drive carrier handle is completely closed.
5
Figure 5-6: Installing the Hard Drive
Warning! Enterprise level hard disk drives are recommended for use in Supermicro
chassis and servers.
5-5
SC825 Chassis Manual
5-5 Installing an Optional Fixed Hard Drive
The SC825 chassis models include two open slots for optional hard disk drives. To
utilize these slots, the dummy drive and the slot cover must be removed.
Removing the Dummy Drive or Hard Disk Drive
1. Disconnect the power supply, lay the chassis on a flat surface, and open the
chassis cover.
2. Press the release tab.
3. Push against the back of the dummy drive, sliding the dummy drive and slot
cover forward, out through the front of the chassis.
4. Insert the drive into rear of the open slot and connect the wiring.
2
Release Tabs
3
Figure 5-7: Removing the Dummy Drive and Slot Cover
5-6
Chapter 5: Chassis Setup and Maintenance
5-6 DVD-ROM Replacement or Installation
Most SC825 chassis models include a DVD-ROM which is usually pre-installed.
Installing or Replacing a DVD-ROM Drive
1. Power down the system and if necessary, remove the server from the rack.
2. Remove the chassis cover.
3. Unplug the drives power and data cables from the motherboard and/or backplane.
4. If you are adding a new DVD-ROM drive: Remove the mini-bezel (grate)
from the drive bay The bezel can be removed by pulling out the hard drive
beneath the DVD-ROM drive bay, then pulling the mini-bezel forward.
If you are replacing a drive: Locate the locking tab at the rear (left hand
side when viewed from the front) of the DVD-ROM drive. Push the tab toward
the drive and push the drive unit out the front of the chassis.
5. Insert the new drive unit in the slot until the tab locks in place.
6. Reconnect the data and power cables.
7. Replace the chassis cover (replace the server in the rack, if necessary) and
power up the system.
Replacing the DVD-ROM and Front Panel
SC825 chassis models include a slim DVD-ROM, and front port panel. Use the
instructions in this section in the unlikely event that you must replace any of these
components.
DVD-ROM
Front Port Panel
Figure 5-8: Install the DVD-ROM and Front Panel
5-7
SC825 Chassis Manual
5-7 Installing the Motherboard
I/O Shield
Figure 5-9: I/O Shield Placement
I/O Shield
The I/O shield holds the motherboard ports in place. Install the I/O shield before
you install the motherboard.
Installing the I/O Shield
Installing the I/O Shield
1. Review the documentation that came with your motherboard. Become familiar
with component placement, requirements, and precautions.
2. Disconnect the power supply, lay the chassis on a flat surface, and open the
chassis cover.
3. With the illustrations facing the outside of the chassis, place the shield into
the space provided.
4. Once installed, the motherboard will hold the I/O shield in place.
5-8
Chapter 5: Chassis Setup and Maintenance
Permanent and Optional Standoffs
Standoffs prevent short circuits by securing space between the motherboard and
the chassis surface. The SC825 chassis includes permanent standoffs in locations
used by most motherboards. These standoffs accept the rounded Phillips head
screws included in the SC825 accessories packaging.
Some motherboards require additional screws for heatsinks, general components
and/or non-standard security. Optional standoffs are included to these motherboards. To use an optional standoff, you must place the hexagonal screw through
the bottom the chassis and secure the screw with the hexagon nut (rounded side
up).
5-9
SC825 Chassis Manual
Installing the Motherboard
1. Review the documentation that came with your motherboard. Become familiar
with component placement, requirements, precautions, and cable connections.
1. Disconnect the power supply, lay the chassis on a flat surface, and open the
chassis cover.
2. As required by your motherboard, install standoffs in any areas that do not
have a permanent standoff. To do this:
A. Place a hexagonal standoff screw through the bottom the chassis.
B. Secure the screw with the hexagon nut (rounded side up).
3. Lay the motherboard on the chassis aligning the permanent and optional
standoffs
4. Secure the motherboard to the chassis using the rounded, Phillips head
screws. Do not exceed eight pounds of torque when tightening down the
motherboard.
5. Secure the CPU(s), heatsinks, and other components to the motherboard as
described in the motherboard documentation.
6. Connect the cables between the motherboard, backplane, chassis, front panel, and power supply, as needed. Also, the fans may be temporarily removed
to allow access to the backplane ports.
Figure 5-10: Chassis Standoffs
5-10
Chapter 5: Chassis Setup and Maintenance
Expansion Card PCI Slot Setup
SC825: chassis include PCI slots for expansion cards. The number of cards you
can use depends on your chassis model.
SC825 LP: Provides seven low-profile PCI slots.
SC825U: Provides three full-height/full-length and three low-profile PCI slots through
a user defined universal expansion card.
PCI Slots
Figure 5-11: SC825 LP model
PCI Slot Setup in LP (Low-Profile) Chassis
SC825 chassis include PCI slots for expansion cards. The number of cards you can
use depends on your chassis model and motherboard model.
Installing Expansion cards in SC825LP (Low-Profile) Chassis
1. Disconnect the power supply, lay the chassis on a flat surface, and open the
chassis cover.
2. Remove the screw holding the cover in place for each low-profile PCI slot you
want to use. Keep this screw for later use.
3. Connect the expansion cards to the mother board.
4. Secure each card to the chassis using the card's L bracket and the screw
previously removed.
5-11
SC825 Chassis Manual
PCI Slot Setup for SC825U (Universal Output) and
SC825W
SC825U and SC825W chassis accepts a slightly smaller "L" shaped motherboard to
allow for a universal expansion card. This universal output card allows the systems
to accept SAS, SCSI, IB, Ethernet, and other types of connections.
SC825U/SC825W chassis are setup similar to 825RC chassis with two differences:
A. The SC825U/SC825W chassis accepts three full-length, full-height expansion
cards instead of four. The fourth slot is used for the UI/O card (SC825U) or a 4x
full-height, full-length card (SC825W).
B. The SC825U/SC825W chassis includes a bracket that extends from the fan row
to the back of the chassis. This bracket provides support for the riser card.
Installing a Universal Input/Output Card in the SC825U chassis:
1. Disconnect the power supply, lay the chassis on a flat surface, and open the
chassis cover.
2. Connect the universal input/output to the motherboard using the slots provided on the motherboard and the back panel.
3. Secure the card to the chassis using the four screws provided with the chassis packaging.
The SC825U chassis accepts 3 full-height/full-length slots and 3 low profile slots.
Installing Add-on Cards in the SC825U and SC825W Chassis
1. Disconnect the power supply, lay the chassis on a flat surface, and open the
chassis cover.
2. If you are using a universal input/output card, make sure it is installed before
continuing (applies only to the SC825U).
3. If you installing low profile expansion cards, remove the chassis air shroud.
4. Secure the card to the chassis using the four screws provided with the chassis packaging.
5-12
Chapter 5: Chassis Setup and Maintenance
5-8 Installing the Air Shroud
Figure 5-12: Air Shroud for SC825LP Chassis
Air shrouds concentrate airflow to maximize fan efficiency. The SC825 chassis air
shroud does not require screws to set up.
Installing the Air Shroud
1. Confirm that your air shroud matches your chassis model. Each shroud is
labeled SC825LP or SC825U,
2. Place air shroud in the chassis. The air shroud fits behind the two fans closest to the power supply.
Note that if a 16 DIMM (13.68" x 13") motherboard is used, it is necessary to use
the optional MCP-310-82502-0N air shroud. For ordering information, visit the
Supermicro website at www.supermicro.com and click on the Where to Buy link.
5-13
SC825 Chassis Manual
Figure 5-13: Air Shroud in Place in the SC825LP Chassis
Checking the Server's Airflow
Checking the Airflow
1. Make sure there are no objects to obstruct airflow in and out of the server. In
addition, if you are using a front bezel, make sure the bezel's filter is replaced
periodically.
2. Do not operate the server without drives or drive trays in the drive bays. Use
only recommended server parts.
3. Make sure no wires or foreign objects obstruct air flow through the chassis.
Pull all excess cabling out of the airflow path or use shorter cables.
The control panel LEDs inform you of system status. See “Chapter 3: System
Interface” for details on the LEDs and the control panel buttons.
Installation Complete
In most cases, the chassis power supply and fans are pre-installed. If you need to
install fans continue to the Systems Fan section of this chapter. If the chassis will be
installed into a rack, continue to the next chapter for rack installation instructions.
5-14
Chapter 5: Chassis Setup and Maintenance
5-9 System Fans
Three heavy duty fans provide cooling for the chassis. These fans circulate air
through the chassis as a means of lowering the chassis internal temperature.
Release Tab
Figure 5-14: System Fan
Replacing a System Fan
1. If necessary, open the chassis while the power is running to determine which
fan has failed. (Never run the server for an extended period of time with the
chassis open.)
2. Turn off the power to the system and unplug the system from the outlet.
3. Remove the failed fan's power cord from the serverboard.
4. Press the fan release tab to lift the failed fan from the chassis and pull it
completely from the chassis.
5. Place the new fan into the vacant space in the housing while making sure the
arrows on the top of the fan (indicating air direction) point in the same direction as the arrows on the other fans.
6. Power up the system and check that the fan is working properly before replacing the chassis cover.
5-15
SC825 Chassis Manual
Figure 5-15: Placing a System Fan
5-16
Chapter 5: Chassis Setup and Maintenance
5-10 Power Supply
Depending on your chassis model, the SC825 Chassis has a 560, 600, 700, 710,
720 or 740 Watt power supply. This power supply is auto-switching capable. This
enables it to automatically sense and operate at a 100v to 240v input voltage. An
amber light will be illuminated on the power supply when the power is off. An illuminated green light indicates that the power supply is operating.
Power Supply Failure
SC825 chassis models have either one or two (redundant) power supplies. In the
unlikely event that the power supply unit fails, if you have a single power supply, the
system will shut down and you will need to replace the power supply unit. SC825
chassis models which include a redundant power supply, will allow for the power
supply to be replaced without powering down the system.
Replacement units can be ordered directly from Supermicro (see the contact information in the Preface).
5-17
SC825 Chassis Manual
Release Tab
Figure 5-16: Removing the Power Supply
Replacing the Power Supply
1. If your chassis includes a redundant power supply (at least two power modules), you can leave the server running and remove only one power supply. If
your server has only one power supply, you must power-down the server and
unplug the power cord before replacing the power supply.
2. Push the release tab (on the back of the power supply) as illustrated.
3. Pull the power supply out using the handle provided.
4. Replace the failed power module with the same model.
5. Push the new power supply module into the power bay until you hear a click.
6. Plug the AC power cord back into the module and power up the server.
5-18
Chapter 5: Chassis Setup and Maintenance
Figure 5-17: Replacing the Power Distributor
Replacing the Power Distributor
Redundant server chassis that are 2U or greater require a power distributor. The
power distributor provides failover and power supply redundancy. In the unlikely
event you must replace the power distributor, do following
1. Power down the server and remove the plug from the wall socket or power
strip.
2. Remove all cable connections to the power supply from the motherboard,
backplane, and other components. Also, remove both power supplies.
3. Locate the power distributor between the power supply and the fan row.
4. Remove the three screws securing the power supply.
5. Gently pull the power distributor from the chassis. Gently guide all the cables
through the power distributor housing.
6. Slide the new power distributor module into the power distributor housing.
Make that you slide the cables through the bottom of the housing.
7. Reconnect all the power cables, replace the power supply, and insert the plug
into the wall.
5-19
SC825 Chassis Manual
Replacing or Installing the Front Port Panel
Replace or Install the Front Port Panel
1. Power down and unplug the system
2. Remove the chassis cover.
3. Disconnect the power and data cables from the front port panel to other chassis
components including the motherboard and backplane.
4. Remove the old port panel by depressing the release tab, then pulling the unit
out of the chassis.
5. Insert the new front port panel unit in the slot until the tab locks into place.
6. Connect the data and power cables to the backplane and motherboard.
For more information, see the manual for your backplane in the appendix.
5-20
Chapter 5: Chassis Setup and Maintenance
5-11 Optional Front Bezel
The SC825 chassis supports an optional full-face locking front bezel for added security. The front bezel is not included with the SC825 chassis, but can be ordered
seperately by visiting the Supermicro website at www.supermicro.com, clicking on
the Where to Buy link and referencing part number MCP-210-82503-0B.
5-21
SC825 Chassis Manual
Notes
5-22
Chapter 6: Rack Installation
Chapter 6
Rack Installation
6-1Overview
This chapter provides a quick setup checklist to get your chassis up and running.
Following these steps in the order given should enable you to have the system
operational within a minimum amount of time.
6-2 Unpacking the System
You should inspect the box the chassis was shipped in and note if it was damaged
in any way. If the chassis itself shows damage you should file a damage claim with
the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold your chassis. It should
be situated in a clean, dust-free area that is well ventilated. Avoid areas where
heat, electrical noise and electromagnetic fields are generated. You will also need
it placed near a grounded power outlet. Be sure to read the Rack and Server Precautions in the next section.
6-3 Preparing for Setup
The box your chassis was shipped in should include two sets of rail assemblies,
two rail mounting brackets and the mounting screws you will need to install the
system into the rack. Please read this section in its entirety before you begin the
installation procedure outlined in the sections that follow.
Choosing a Setup Location
•Leave enough clearance in front of the rack to enable you to open the front
door completely (~25 inches).
•Leave approximately 30 inches of clearance in the back of the rack to allow for
sufficient airflow and ease in servicing.
•This product is for installation only in a Restricted Access Location (dedicated
equipment rooms, service closets and the like).
6-1
SC825 Chassis Manual
Rack Precautions
•Ensure that the leveling jacks on the bottom of the rack are fully extended to
the floor with the full weight of the rack resting on them.
•In single rack installation, stabilizers should be attached to the rack.
•In multiple rack installations, the racks should be coupled together.
•Always make sure the rack is stable before extending a component from the
rack.
•You should extend only one component at a time - extending two or more simultaneously may cause the rack to become unstable.
General Server Precautions
•Review the electrical and general safety precautions that came with the components you are adding to your chassis.
•Determine the placement of each component in the rack before you install the
rails.
•Install the heaviest server components on the bottom of the rack first, and then
work up.
•Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
•Allow the hot plug hard drives and power supply modules to cool before touching them.
•Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.
6-2
Chapter 6: Rack Installation
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient temperature (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connections other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).
To prevent bodily injury when mounting or servicing this unit in a rack, you
must take special precautions to ensure that the system remains stable.
The following guidelines are provided to ensure your safety:
•This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
•When mounting this unit in a partially filled rack, load the rack from the bottom
to the top with the heaviest component at the bottom of the rack.
•If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.
6-3
SC825 Chassis Manual
6-4 Rack Mounting Instructions
This section provides information on installing the SC825 chassis into a rack unit
with the quick-release rails provided. There are a variety of rack units on the market,
which may mean the assembly procedure will differ slightly. You should also refer to
the installation instructions that came with the rack unit you are using.
NOTE: This rail will fit a rack between 26" and 33.5" deep.
Separating the Sections of the Rack Rails
The chassis package includes two rail assemblies in the rack mounting kit. Each
assembly consists of two sections: an inner fixed chassis rail that secures directly
to the server chassis and an outer fixed rack rail that secures directly to the rack
itself.
1
F.
Rail Assembly
Separating the Inner and Outer Rails
SCREW
1. Locate the rail assembly in the chassis
packaging.
Extending the Rails
12
2. Extend the rail assembly by pulling it
outward.
2
1
3. Press the quick-release tab.
13
Quick-Release
Tab
4. Separate the inner rail extension from
the outer rail assembly.
14
Separating the Inner
Rail Extension
Figure 6-1: Separating the Rack Rails
SCREW
screw the handles the
outer rails for secure
Warning: do not pick up the server by the front handles. They
are designed
purpose if necessary
to pull the system from a rack only.
6-4
Chapter 6: Rack Installation
13
2
13
1
Figure 6-2: Installing the Inner Rail Extensions
Installing the Inner Rail Extension
The SC825 chassis includes a set of inner rails in two sections: inner rails and inner
rail extensions. The inner rails are pre-attached to the chassis, and do not interfere
with normal use of the chassis if you decide not to use a server rack. The inner rail
extension is attached to the inner rail to mount the chassis in the rack.
Installing the Inner Rails
1. Place the inner rail extensions on the side of the chassis aligning the hooks
of the chassis with the rail extension holes. Make sure the extension faces
"outward" just like the pre-attached inner rail.
2. Slide the extension toward the front of the chassis.
3. Optional: Secure the chassis with 2 screws as illustrated. Repeat steps for
the other inner rail extension.
Stability hazard. The rack stabilizing mechanism must be in place, or the
rack must be bolted to the floor before you slide the unit out for servicing.
Failure to stabilize the rack can cause the rack to tip over.
6-5
SC825 Chassis Manual
13
1
SCREW
screw the handles the
outer rails for secure
purpose if necessary
12
Figure 6-3: Assembling the Outer Rails
Outer Rack Rails
Outer rails attach to the rack and hold the chassis in place. The outer rails for the
SC825 chassis extend between 30 inches and 33 inches.
Installing the Outer Rails to the Rack
1. Secure the back end of the outer rail to the rack, using the screws provided.
2. Press the button where the two outer rails are joined to retract the smaller
outer rail.
3. Hang the hooks of the rails onto the rack holes and if desired, use screws to
secure the front of the outer rail onto the rack.
4. Repeat steps 1-3 for the remaining outer rail.
6-6
2
F.
Chapter 6: Rack Installation
SCREW
1
Figure 6-4: Installing the Chassis into the Rack
Note: figures are for illustrative purposes only. Always install servers into racks
from the bottom up.
Installing the Chassis into a Rack
1. Extend the outer rails as illustrated above.
2. Align the inner rails of the chassis with the outer rails on the rack.
SCREW
3. Slide the inner rails into the outer rails, keeping the pressure even on both
sides.
thethe
chassis has been pushed completely into the rack, it should
screw
theWhen
handles
outer
rails
secure
click
intofor
the
locked position.
purpose if necessary
4. Optional screws may be used to secure the to hold the front of the chassis to
COMPLETE
ABLECOM
DATE:2008/08/14
the rack.
REV:2
6-7
SC825 Chassis Manual
Notes
6-8
Appendix A: Chassis Cables
Appendix A
SC825 Chassis Cables
A-1Overview
This appendix lists supported cables for your chassis system. It only includes the
most commonly used components and configurations. For more compatible cables,
refer to the manufacturer of the motherboard you are using and our Web site at:
www.supermicro.com.
A-2 Cables Included with SC825TQ Universal I/O
Chassis
SC825TQ-R700U
Part #
Type
Length
Description
CBL-0157L
Cable
9"
8 pin to 8 pin ribbon cable for
SGPIO, PB free
CBL-0087
Ribbon,
Round
20"
16 pin to 16 pin ribbon cable for
control panel
CBL-0179L
Cable
70 cm
Cable
6'
SATA
various
CBL-0180L-01
SATA cable
Two regional power cords
Set for 4 SATA cables. Length varied to minimize airflow interference.
A-3 Cables Included with SC825TQ Chassis (SAS/SATA)
SC825TQ-R700RC2/R700RC
Part #
Type
Length
Description
8 pin to 8 pin ribbon cable for
SGPIO, PB free
CBL-0157L
Cable
9"
CBL-0191L
Cable
50 cm
20 pin to 20 pin cable for control
panel
CBL-0179L
Cable
70 cm
SATA cable
Cable
6'
SATA
various
CBL-0180L
Two regional power cords
A-1
Set for 4 SATA Cables. Length varied to minimize airflow interference.
SC825 Chassis Manual
SC825TQ-R700LP
Part #
Type
Length
CBL-0157L
Ribbon
9"
8 pin to 8 pin ribbon cable for
SGPIO, PB free
CBL-0087
Ribbon,
Round
20"
16 pin to 16 pin ribbon cable for
control panel
CBL-0979L
Cable
70 cm
Cable
6'
SATA
various
CBL-0180L-01
Description
SATA cable
Two regional power cords
Set for 4 SATA Cables. Length varied to minimize airflow interference.
SC825TQ-R710LP
Part #
Type
Length
Description
CBL-0157L
Ribbon
9"
8 pin to 8 pin ribbon cable for
SGPIO, PB free
CBL-0084
Split
cable
6"
16 pin front control split cable
CBL-0160L
Cable
---
Regional power cord
CBL-0180L
SATA
various
Part #
Type
Length
Ribbon
9"
CBL-0180L-01
SATA
various
CBL-0044L
SATA
61cm
CBL-0082L
SATA
---
Y-split SATA power adapter
CBL-0296L
Cord
9"
Fan extension cord
Part #
Type
Length
CBL-0157L
Cable
9"
CBL-0071L
Round
Cable
70 cm
Cable
6'
SATA
various
Set for 4 SATA cables. Length varied to minimize airflow interference.
SC825TQ-R720LP/ SC825TQ-R720U
CBL-0157L
Description
8 pin to 8 pin ribbon cable for
SGPIO, PB free
SATA set of 4-70/59/48/38CM round
S-RA, PBF
SATA cable, S-S
SC825TQ-R740LPB
CBL-0180L-01
Description
8 pin to 8 pin ribbon cable for
SGPIO, PB free
16-pin TO 16 -pin ribbon FB cable
30
Two regional power cords
A-2
Set for 4 SATA cables. Length varied to minimize airflow interference.
Appendix A: Chassis Cables
SC825TQ-560LP
Part #
Type
Length
CBL-0157L
Ribbon
9"
8 pin to 8 pin ribbon cable for
SGPIO, PB free
CBL-0087
Ribbon,
Round
20"
16 pin to 16 pin ribbon cable for
control panel
CBL-0179L
Cable
70 cm
Cable
6'
SATA
various
CBL-0180L
Description
SATA cable
Regional power cord
Set for 4 SATA Cables. Length varied to minimize airflow interference.
SC825TQ-R740WB
Part #
Type
Length
Description
8 pin to 8 pin ribbon cable for
SGPIO, PB free
CBL-0157L
Ribbon
9"
CBL-0044L
SATA
61cm
CBL-0082L
SATA
---
Y-split SATA power adapter
CBL-0296L
Cord
9"
Fan extension cord
CBL-0180L
SATA
various
SATA cable, S-S
Set for 4 SATA Cables. Length varied to minimize airflow interference.
SC825TQ-R500WB, SC825TQ-600WB,
Part #
Type
Length
CBL-0157L
Cable
9"
8 pin to 8 pin ribbon cable for
SGPIO, PB free
CBL-0087
Ribbon,
Round
20"
16 pin to 16 pin ribbon cable for
control panel
CBL-0071L
Round
Cable
70 cm
Cable
6'
SATA
various
CBL-0180L-01
Description
16-pin TO 16 -pin ribbon FB cable
30
Two regional power cords
A-3
Set for 4 SATA cables. Length varied to minimize airflow interference.
SC825 Chassis Manual
A-4 Compatible Cables
These cables are compatible with the SC825 Chassis.
Alternate SAS/SATA Cables
Some compatible motherboards have different connectors. If your motherboard
has only one SAS connector that the SAS/SATA cables must share, use one of the
following cables. These cables must be purchased separately.
Cable Name: SAS Cable
Quantity: 1
Part #: CBL-0175L
Alt. Name: "Big Four"
Description: This cable has one SFF-8484 (32 pin) connector on one end and
4 SAS connectors (7 pins each) at the other. This cable connects from the host
(motherboard or other controller) to the backplane SAS hard drive port.
Cable Name: SAS Cable
Quantity: 1
Part #: CBL-0116
Alt. Name: iPass or "Small Four"
Description: This cable has one ipass (SFF-8087/mini-sas) connector (36 pins) at
one end and 4 SAS connectors on one end. This cable connects from the Host
(motherboard or other controller) to the backplane SAS hard drive port.
A-4
Appendix A: Chassis Cables
Extending Power Cables
Although Supermicro chassis are designed to be efficient and cost-effective, some
compatible motherboards have power connectors located in different areas.
To use these motherboards you may have to extend the power cables to the mother
boards. To do this, use the following chart as a guide.
Power Cable Extenders
Number of Pins
Cable Part #
Length
24 pin
CBL - 0042
7.9”(20 CM)
20 pin
CBL - 0059
7.9”(20 CM)
8 pin
CBL - 0062
7.9”(20 CM)
4 pin
CBL - 0060
7.9”(20 CM)
Front Panel to the Motherboard
The SC825 chassis includes a cable to connect the chassis front panel to the
motherboard. If your motherboard uses a different connector, use the following list
to find a compatible cable.
Front Panel to Motherboard Cable (Ribbon Cable)
Number of Pins
(Front Panel)
Number of Pins
(Motherboard
Cable Part #
16 pin
16 pin
CBL - 0049
16 pin
20 pin
CBL - 0048
20 pin
20 pin
CBL - 0047
16 pin
various*
CBL - 0068
20 pin
various*
CBL - 0067
* Split cables: Use these cable if your motherboard requires several different connections from the front panel.
A-5
SC825 Chassis Manual
Notes
A-6
Appendix B: Power Supply Specifications
Appendix B
SC825 Power Supply Specifications
This appendix lists power supply specifications for your chassis system.
SC825 Series
500W
MFR Part #
PWS-501P1R
560W
600W
R700W
(Redundant)
PWS-561-1H20
PWS-605P-1H
PWS-702A-IR
100 - 240V
50 - 60Hz
8.5 - 4 Amp
---
100 - 240V
60-50Hz
10 - 4 Amp
---
100-240 V, 5060 Hz, 7.5 Amp
max
---
---
---
---
4 Amp @
+5V standby
41.7 Amp @
+12V
---
---
---
+5V: 30 Amp
With Power +3.3V: 24
Distributor Amp -12V:
0.6 Amp
---
---
---
3 Amp
3 Amp
4 Amp
43.6 Amp
49 Amp
57 Amp
Rated AC
Voltage
AC Input
100-240 V,
50-60 Hz,
6.1-2.6 Amp
DC Input
Voltage
DC Output
+5V
standby
+12V
+5V
25 Amp
18 Amp
24 Amp
+3.3V
21 Amp
15 Amp
21 Amp
-12V
0.6 Amp
0.5
0.6 Amp
B-1
SC825 Chassis Manual
SC825 Series
710W
DC-DC Power
Supply
R720W
(Redundant)
740W
MFR Part #
PWS-711-1R
PWS-721P-1R
PWS-741P-1R
Rated AC
Voltage
---
---
100-240 V, 50-60 Hz
9-3.5 Amp
AC Input
---
100-240 V, 50-60
Hz, 4-9 Amp
---
DC Input Voltage
Voltage Range =
-36V to -75V (24A
- 11A)
Nominal Voltage =
-48V
---
---
DC Output
---
3 Amp @ +5V
standby
59 Amp @ +12V
4 Amp @ +5V
standby
61.7 Amp @ +12V
+5V standby 4 Amp
---
---
+12V
59 Amp
---
---
+5V
30 Amp
45 Amp
---
+3.3V
20 Amp
24 Amp
---
-12V
0.6 Amp
0.6 Amp
---
B-2
Appendix C: BPN-SAS-825TQ Backplane Specifications
Appendix C
BPN-SAS-825TQ Backplane Specifications
To avoid personal injury and property damage, carefully follow all the safety steps
listed below when accessing your system or handling the components.
C-1 ESD Safety Guidelines
Electrostatic Discharge (ESD) can damage electronic com­ponents. To prevent damage to your system, it is important to handle it very carefully. The following measures
are generally sufficient to protect your equipment from ESD.
•Use a grounded wrist strap designed to prevent static discharge.
•Touch a grounded metal object before removing a component from the antistatic
bag.
•Handle the backplane by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
•When handling chips or modules, avoid touching their pins.
•Put the card and peripherals back into their antistatic bags when not in use.
C-2 General Safety Guidelines
•Always disconnect power cables before installing or removing any components
from the computer, including the BPN-SAS-825TQ backplane.
•Disconnect the power cable before installing or removing any cables from the
BPN-SAS-825TQ backplane.
•Make sure that the BPN-SAS-825TQ backplane is securely and properly in-
stalled on the motherboard to prevent damage to the system due to power
shortage.
C-1
SC825 Chassis Manual
C-3 An Important Note to Users
All images and layouts shown in this user's guide are based upon the latest PCB
Revision available at the time of publishing. The card you have received may or
may not look exactly the same as the graphics shown in this manual.
C-4 Introduction to the BPN-SAS-825TQ Backplane
The BPN-SAS-825TQ backplane has been designed to utilize the most up-to-date
technology available, providing your system with reliable, high-quality performance.
This manual reflects BPN-SAS-825TQ Revision 2.0, the most current release available at the time of publication. Always refer to the Supermicro web site at www.supermicro.com for the latest updates, compatible parts and supported configurations.
C-2
Appendix C: BPN-SAS-825TQ Backplane Specifications
C-5 Front Connectors and SAS Ports
+12V
GND
GND
+5V
+12V
GND
GND
15 16 18
14
13
12
10
1
+5V
1
ACT_IN
SAS825TQ
+ +
REV 2.0
++
++
++
+
+
JP29:9072 RESET
++
11
1
BAR CODE
48
1
2
#2
IC
SIDEBAND #2
1
++
1
16
17
2
#1
IC
32
SIDEBAND #1
19
Figure C-1: Front Connectors
Front Connectors
SAS Ports
1. 4-pin power connector: JP13
12.SAS Port #0
2. 4-pin power connector: JP10
13.SAS Port #1
3. CD-ROM/floppy connector: JP18
14.SAS Port #2
4. CD-ROM/floppy connector: JP17
15.SAS Port #3
5. SAS activity LED header: JP26
16.SAS Port #4
6. I2C connector #2: JP45
17.SAS Port #5
7. I2C connector #1: JP44
18.SAS Port #6
8. Sideband connector #2: JP52
19.SAS Port #7
9. Sideband connector #1: JP51
10.MG9072 chip
11. Upgrade header: JP46
ACT_IN
GND
GND
118
+5V
1
+ +
115
+12V
++
19
1
+5V
+
+
JP29:9072 RESET
++
GND
14
1
17
1
48
1
++
GND
16
32
#2
13
1
BAR CODE
2
IC
SIDEBAND #2
16
1
SAS825TQ
REV 2.0
Figure C-2: Front SAS Ports
C-3
2
IC
1
++
+12V
#1
112
SIDEBAND #1
++
SC825 Chassis Manual
C-6 Front Connector and Pin Definitions
#1 and #2 Backplane Main Power Connectors
Backplane
Main Power
4-Pin Connector
The 4-pin connectors, designated JP10, and
JP13 provide power to the backplane. See
the table on the right for pin definitions.
Pin#
Definition
+12V
1
2 and 3
4
#3 and #4 CD-ROM/Floppy Pin Connectors
Pin#
+5V
2 and 3
4
Ground
+12V
SAS Activity LED Header
Pin Definitions
Pin #
Definition
Pin #
Definition
1
ACT IN#0
6
ACT IN#4
2
ACT IN#1
7
ACT IN#5
3
ACT IN#2
8
ACT IN#6
4
ACT IN#3
9
ACT IN#7
5
Ground
10
Empty
#6 and #7 I2C Connectors
I2C Connector
Pin Definitions
2
C-4
Definition
1
#5 Activity LED Headers
The I C Connectors, designated JP44 and
JP45, are used to monitor the HDD activity
and status. See the table on the right for pin
definitions.
+5V
CD-ROM/FDD Power
4-Pin Connector
Pin connectors designated J17 and J18,
provide power to the CD-ROM and floppy
drives. See the table on the right for pin
definitions.
The activity LED header, designated JP26
is used to indicate the activity status of
each SAS drive. The activity LED header is
located on the front panel. For the activity
lead header to work properly, connect to it
using a 10-pin LED cable. This is only used
when the activity LED is not supported by
the hard drive.
Ground
Pin#
Definition
1
Data
2
Ground
3
Clock
4
No Connection
Appendix C: BPN-SAS-825TQ Backplane Specifications
#8 and #9 Sideband Headers
Sideband Headers
The sideband headers are designated JP51
and JP52. For SES-2 to work properly, you
must connect an 8-pin sideband cable. See
the table to the right for pin definitions.
#10 MG9072 Chip
The MG9072 is an enclosure management
chip that supports the SES-2 controller and
SES-2 protocols.
#11 Upgrade Header
The upgrade header is designated JP46 and is
used for manufacturing purposes only.
#12 to #19 SAS Ports
The SAS ports are used to connect the SAS
drive cables. The eight ports are designated
#0 - #7. Each port is also compatible with
SATA drives.
C-5
Pin #
Definition
Pin #
Definition
2
SGPIO:
SDIN;
I2C:
Backplane
Addressing
1
Controller
ID (SB6)
4
SGPIO:
SDOUT;
I2C: Reset
3
GND (SB2)
6
GND (SB3)
5
SGPIO:
SLOAD;
I2C: SDA
8
Backplane
ID (SB7)
7
SGPIO:
SCLOCK;
12C: SCL
10
No Connection
9
No Connection
SC825 Chassis Manual
C-7 Front Jumper Locations and Pin Definitions
JP43
ACT_IN
GND
GND
+5V
+12V
GND
GND
JP36
1
#2
SIDEBAND #2
1
SAS825TQ
REV 2.0
48
1
++
++
+ +
++
+
+
JP29:9072 RESET
JP29
JP50
JP38
++
JP18
2
IC
+5V
BAR CODE
2
IC
#1
++
+12V
JP37
JP33
JP34
JP41
JP40
Figure C-3: Front Jumpers
16
32
SIDEBAND #1
JP42
Explanation of Jumpers
To modify the operation of the backplane,
jumpers can be used to choose between
optional settings. Jumpers create shorts
between two pins to change the function
of the connector. Pin 1 is identified with
a square solder pad on the printed circuit
board. Note: On two pin jumpers, "Closed"
means the jumper is on and "Open" means
3
Connector
Pins
2
1
Open, jumper off
the pins.
Jumper
Closed, jumper on
the pins.
3
2
1
Setting
the jumper is off the pins.
Jumper Settings
Jumper
Jumper Settings
Note
JP29
Open (Jumper off the pins): Default
Closed (Jumper on the pins): Reset
MG9072 chip reset
JP18
Open (Jumper off the pins): Default
Closed (Jumper on the pins): Reset
Buzzer reset*
*The buzzer sound indicates that a condition requiring immediate attention has
occurred.
The buzzer alarm is triggered by the following conditions:
1. Hard drive failure
2. System temperature over 45º Celsius.
C-6
Appendix C: BPN-SAS-825TQ Backplane Specifications
SGPIO and I2C Modes and Jumper Settings
This backplane can utilize SGPIO or I2C, which is the default mode and can be
used without making changes to your jumpers. The following information describes
which jumper must be configured to use SGPIO mode.
SGPIO Settings
Jumper
Jumper Setting
Notes
JP33
1-2
Controller ID #1
JP34
1-2
Backplane ID #1
1-2: ID#0
JP36
1-2
Controller ID #2
JP37
1-2
Backplane ID #2
1-2: ID#0
JP38
Open (Jumper off the pins)
I2C Reset #2
JP40
Closed (Jumper on the pins)
I2C Reset_SDOUT#1
JP41
Closed (Jumper on the pins)
I2C Reset_SDOUT#2
JP42
1-2
I2C Backplane ID_SDIN#1
JP43
1-2
I2C Backplane ID_SDIN#2
JP50
Open (Jumper off the pins)
I2C Reset #1
C-7
SC825 Chassis Manual
I2C Settings (Default)
Jumper
Jumper Setting
Notes
JP33
Pins 2-3
Controller ID #1
JP34
Pins 1-2
Backplane ID #1
1-2: ID#0
2-3: ID#1
JP36
Pins 2-3
Controller ID #2
JP37
Pins 2-3
Backplane ID #2
1-2: ID#0
2-3: ID#1
JP38
Closed (Jumper on the pins)
I2C Reset #2
JP40
Open (Jumper off the pins)
I2C Reset_SDOUT#1
JP41
Open (Jumper off the pins)
I2C Reset_SDOUT#2
JP42
Pins 2-3
I2C Backplane ID_SDIN#1
JP43
Pins 2-3
I2C Backplane ID_SDIN#2
JP50
Closed (Jumper on the pins)
I2C Reset #1
C-8
Appendix C: BPN-SAS-825TQ Backplane Specifications
SAS Port Connections in I2C and SGPIO Settings
Use the following chart when connecting this backplane. If the SAS ports are connected out of order, it is not easy to identify drives using the LED function.
SAS Port Connections in I2C and SGPIO Settings
Port #
I2C
SGPIO
#0-3
I2C #1
Sideband #1
#4-7
I2C #2
Sideband #2
Front LED Indicators
ACT_IN
+12V
GND
GND
+5V
+12V
GND
GND
2
#2
IC
SIDEBAND #2
+5V
1
1
SAS825TQ
+ +
REV 2.0
48
BAR CODE
2
IC
#1
++
++
1
++
++
++
16
32
+
+
D3
JP29:9072 RESET
SIDEBAND #1
Figure C-4: Front LED
Front Panel LEDs
LED
D3
State
On
Specification
Overheat/drive failure LED indicator.
(Red light: Flashing. Buzzer: On, if activated)
C-9
SC825 Chassis Manual
Rear
Connector
SAS Drive
Number
SAS #0 J1
SAS/SATA HDD #0
SAS #4 J9
SAS/SATA HDD #4
SAS #1 J2
SAS/SATA HDD #1
SAS #5 J11
SAS/SATA HDD #5
SAS #2 J3
SAS/SATA HDD #2
SAS #6 J13
SAS/SATA HDD #6
SAS #3 J4
SAS/SATA HDD #3
SAS #7 J15
SAS/SATA HDD #7
Rear LED Indicators
Rear LED
Hard Drive Activity
Failure LED
SAS #0
D12
D5
SAS #1
D13
D6
SAS #2
D14
D7
SAS #3
D15
D8
SAS #4
D18
D19
SAS #5
D21
D20
SAS #6
D22
D23
SAS #7
D25
D26
C-10
ACT7
FAIL7
D26
D15
ACT3
FAIL3
D8
ACT6
D22
D23
FAIL6
ACT2
D14
D7
FAIL2
D21
ACT5
D20
FAIL5
ACT1
D13
D6
R155
R156
C106
FAIL1
ACT4
D18
D19
FAIL4
ACT0
D12
D5
FAIL0
SAS Drive
Number
+
Rear
Connector
+
Rear SAS/SATA Connectors
+
Figure C-5: Rear Connectors and LEDs
D25
D26
D15
D8
+
+
D14
D7
SAS #7
J15
SAS #3
J4
+
+
SAS #2
J3
D22
D23
+
+
SAS #6
J13
+
+
+
SAS #1
J2
+
D13
D6
+
D12
D5
D21
D20
SAS #5
J11
+
SAS #0
J1
D18
D19
+
SAS #4
J9
D25
C-8 Rear Connectors and LED Indicators
Appendix C: BPN-SAS-825TQ Backplane Specifications
Notes
C-11
SC825 Chassis Manual
Disclaimer (cont.)
The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,
aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic
property damage. Accordingly, Supermicro disclaims any and all liability, and should
buyer use or sell such products for use in such ultra-hazardous applications, it does so
entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold
Supermicro harmless for and against any and all claims, demands, actions, litigation,
and proceedings of any kind arising out of or related to such ultra-hazardous use or
sale.
C-12