Yamaha TSX-15 Owner`s manual

OWNER'S MANUAL
AB
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
Install this unit in a well ventilated, cool, dry, clean
place - away from direct sunlight, heat sources,
vibration, dust, moisture and cold. For proper
ventilation, allow the following minimum clearances.
Top: 15 cm (6 in)
Rear: 10 cm (4 in)
Sides: 10 cm (4 in)
Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this unit
in an environment with high humidity (i.e. a room
with a humidifier) to prevent condensation inside this
unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
Avoid installing this unit where foreign object may
fall onto this unit and/or this unit may be exposed to
liquid dripping or splashing. On the top of this unit,
do not place:
– Other components, as they may cause damage
and/or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall
and liquid may cause electrical shock to the user
and/or damage to this unit.
Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause
fire, damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may
overheat, possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall
outlet, grasp the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified is
dangerous and may cause fire, damage to this unit,
and/or personal injury. Yamaha will not be held
responsible for any damage resulting from use of this
unit with a voltage other than specified.
To prevent damage by lightning, keep the power
cable disconnected from a wall outlet or this unit
during a lightning storm.
Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
i En
15 When not planning to use this unit for long periods of
time (i.e. vacation), disconnect the AC power plug
from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press
to set the system to
off, and disconnect the AC power plug from the wall
outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the system off, then leave this
unit alone for cooling.
20 Install this unit near the wall outlet and where the AC
power plug can be reached easily.
21 Be sure to use the AC adaptor supplied with this unit.
Using an AC adaptor other than the one provided
may cause fire or damage to this unit.
This unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off by . In this state, this unit is
designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
• This unit’s speakers use magnets. Do not place items
that are sensitive to magnetism, such as CRT-type TVs,
clocks, credit cards, floppy disks, etc., on or beside this
unit.
• There is a chance that placing this unit too close to a
CRT-based (Braun tube) TV set might impair picture
color. Should this happen, move this unit away from the
TV set.
Do not use this unit within 22 cm (9 inches) of persons
with a heart pacemaker implant or defibrillator implant.
Radio waves may affect electro-medical devices.
Do not use this unit near medical devices or inside
medical facilities.
We, Yamaha Music Europe GmbH hereby
declare that this unit is in compliance with the
essential requirements and other relevant
provisions of Directive 1999/5/EC.
Yamaha Music Europe GmbH
Siemensstr. 22-34 25462 Rellingen, Germany
Tel: +49-4101-303-0
PREPARATION
Information for Users on Collection and Disposal of Old Equipment
This symbol on the products, packaging, and/or accompanying documents means that used electrical and
electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products, please take them to applicable collection
points, in accordance with your national legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable resources and prevent any potential
negative effects on human health and the environment which could otherwise arise from inappropriate
waste handling.
For more information about collection and recycling of old products, please contact your local
municipality, your waste disposal service or the point of sale where you purchased the items.
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these items, please contact your
local authorities or dealer and ask for the correct method of disposal.
CONTENTS
NAMES OF PARTS AND THEIR FUNCTIONS .................................................................................... 2
BASIC FUNCTIONS................................................................................................................................... 4
LISTENING TO FM STATIONS .............................................................................................................. 6
LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE ................................................................ 7
LISTENING TO EXTERNAL SOURCES ............................................................................................. 10
CHARGING WITH THE USB PORT .................................................................................................... 10
TROUBLESHOOTING ............................................................................................................................ 11
SPECIFICATIONS ................................................................................................................................... 13
■ Features
–
–
–
–
–
Playback of Bluetooth devices, FM radio, and external devices with an AUX connector.
Setting alarm using an FM radio.
Supplying power to smartphones, tablets, etc. via USB port on the rear panel.
Rich sound by 5cm full-range custom speaker and DSP (Digital Signal Processor) made by Yamaha.
Enhanced treble and thick mid/bass, even when playing a compressed audio source, such as MP3, etc.
(Music Enhancer)
• Note indicates precautions for use of the unit and its feature limitations.
•
y
indicates supplementary explanations for better use.
■ Supplied accessories
AC adaptor
FM antenna
DC 12 V, 1.5 A, model number:
• Australian model
MU18-D120150-A3
• U.K. model
MU18-D120150-B2
1 En
NAMES OF PARTS AND THEIR FUNCTIONS
■ Top panel
A VOLUME
Controls volume. When you
control the volume, the volume
level will be displayed on the
display for a while.
I Grille (☞ page 3)
B CLOCK
Sets the clock (☞ page 4).
C ALARM
Sets the alarm (☞ page 4).
D TUNING
Adjust the time or radio frequency
(☞ page 4, 6).
E PRESET
Stores up to five favorite FM radio
stations (☞ page 6).
F SOURCE (PAIRING)
Selects an input source from
(Bluetooth), AUX, or RADIO.
G Display
H Indicators
(Alarm): Lights when the alarm
function is on (☞ page 4).
RADIO: Lights when the radio is selected
as an input source (☞ page 6).
AUX: Lights when AUX is selected as an
input source (☞ page 10).
(Bluetooth): Lights when ( ) Bluetooth
is selected as an input
source or during Bluetooth
pairing/connection
(☞ page 7, 9).
y Dimmer function
Press CLOCK repeatedly to set the
brightness of the display and indicators.
3 (brightest)
2
1 (darkest)
2 En
J
Press to turn on the system or enter standby mode.
Eco Standby mode
• This can reduce power consumption. Press and hold
for
more than 3 seconds to set the system to power saving mode.
All the indicators and display turn off, and Bluetooth operation,
audio playback, input via buttons except
are disabled. To
cancel Eco Standby mode, press .
• Even in standby mode or Eco Standby mode, the alarm
function is available.
Auto Standby (☞ page 5)
• This unit has a function that automatically activates standby
mode when no audio signal is input from a connecting device,
or when the connecting device is playing at a low volume for a
certain period (about 20 minutes).
NAMES OF PARTS AND THEIR FUNCTIONS
Caution
A grille is attached to this product to protect the speakers.
• Since the grille cloth is made of soft material, it can be easily damaged, so do not scratch it with a sharp object.
• Do not overstress the grille cloth. If it is overstressed, it will become contorted and damaged. This may cause damage to
the speakers. Be careful when handling the grille cloth.
■ Rear panel
K CHARGING
Supplies 5 V/1 A to a
portable device, such as
a smartphone, when it is
connected with a USB
cable. (☞ page 10)
L 12 V
Connect the
supplied AC
adaptor.
To AC wall outlet
M AUX
Connect external devices
with ø3.5mm stereo mini
plug cables. (☞ page 10)
N FM ANT
FM antenna terminal
Connecting the FM antenna
A
A Connect the supplied antenna to the
unit.
B Pin the antenna where the best
reception is obtained.
Note
B
• Be sure to stretch out the antenna as the illustration shows.
• If FM reception is poor, change the height or direction of
the antenna, or relocate the unit.
Caution
If you listen to an FM radio station while USB charging,
noise may interfere with the radio reception. In this case,
disconnect the USB cable from the unit.
3 En
OPERATION
BASIC FUNCTIONS
Adjusting the clock
A Press and hold CLOCK for more than
2 seconds.
A, C
The display flashes.
B
B Adjust the time with TUNING.
y
If you press and hold TUNING, the numbers
advance quickly.
C Press CLOCK.
If you want to cancel clock setting mode, press
.
y
If you press PRESET in step B, you can select the
time display method (12 hours/24 hours).
Note
The time settings are lost approximately one week after
unplugging the unit.
Alarm setting
This unit can play back the radio and emit beeps at the set time.
■ Setting the time and sound
A Press and hold ALARM for more than
2 seconds.
A, D
C
The alarm indicator (
), the RADIO
indicator and display flash.
B
Alarm
indicator
(
)
B Set the alarm time with TUNING.
C Set the alarm volume with VOLUME.
The volume level is displayed.
RADIO indicator
Note
If you press ALARM to complete the setting of the alarm
without changing the alarm time and volume, the alarm
setting mode will be cancelled and the alarm will not be set
to on.
4 En
D Press ALARM.
Alarm is set and the alarm indicator (
) lights.
y
• The alarm type of this unit is the radio and beeping
only.
• The radio turns on 3 minutes before the alarm time
and beeping starts at the alarm time.
BASIC FUNCTIONS
■ Switching the alarm on/off
Press ALARM.
When the alarm is on, the alarm indicator (
)
and the RADIO indicator light and the alarm time is
displayed for a while.
Alarm
indicator
(
)
RADIO indicator
Operations during playing back alarm sound
At the set time, alarm sound plays back. During playback, operations below are available.
■ Stopping the alarm
Press ALARM or
.
y
Alarm
indicator
(
)
RADIO indicator
• Unless you stop the alarm, the alarm stops after
60 minutes automatically.
• When you stop the alarm, the alarm time setting, etc., is
saved for convenient use next time.
• Press any button except ALARM and
once to stop the
beeping, and twice to stop the radio source (snooze
function). 4 minutes after the radio source is stopped, it
will start fading in again and after another minute the
beeping will resume.
• When the snooze function is activated, the display, alarm
indicator (
) and RADIO indicator flash.
Auto Standby
The system automatically enters standby mode under the following circumstance.
• No audio signal is input from a connecting device or when the connecting device is playing at a low volume
for a certain period (about 20 minutes).
• If no operation is performed for more than 8 hours while music is being played back or stopped.
• Disconnect the Bluetooth connection from the Bluetooth device.
5 En
LISTENING TO FM STATIONS
Tuning radio stations
A Press SOURCE to select RADIO.
The RADIO indicator lights.
B
B For automatic tuning, press and hold
TUNING.
For manual tuning, press TUNING
repeatedly.
Note
A
If you tune into a station manually, the sound is monaural.
RADIO indicator
Presetting radio stations
You can store up to five favorite FM radio stations with the preset function.
A Press TUNING to select a favorite radio
station.
The radio frequency is displayed temporally.
A
B, C, D
B Press and hold PRESET for more than
2 seconds.
The preset number is displayed on the display and
flashes.
RADIO indicator
C Press PRESET to select the preset
number you want to store to.
The preset number is displayed as follows:
P1
P2
P3
P4
P5
P1
D Press and hold PRESET for more than
2 seconds to complete.
Selecting preset radio stations
A Press SOURCE to select RADIO.
The RADIO indicator lights.
B Press PRESET repeatedly to select the
preset radio station.
A
B
RADIO indicator
6 En
LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE
This unit provides Bluetooth functionality. You can enjoy wireless music playback from your Bluetooth device
(smartphone, digital audio player, etc.). Please also refer to the owner’s manual of your Bluetooth device.
Installation
Within 10 m (33 ft)
Install in a stable place, being careful of
the following points:
• Do not place on top of steel or other
metal plates.
• Do not cover with a cloth, etc.
• Install in the same room as the device
with which signals are to be exchanged
(Bluetooth profile A2DP compatible
smartphone, digital audio player, etc.)
within a direct line-of-sight distance of
10 m (33 ft).
• Make sure there are no obstacles
between this unit and the Bluetooth
device.
Pairing this unit with your Bluetooth device
y What is pairing?
Pairing is an operation that registers the communicating device (subsequently called “the connecting
device”) with this unit. You will need to perform the pairing operation the first time you use your Bluetooth
device with this unit, or if the pairing settings have been deleted. Once pairing has been completed,
subsequent reconnection will be easy even after the Bluetooth connection is disconnected. If pairing is not
successful, refer to the item “Bluetooth” in “TROUBLESHOOTING” (☞ page 12).
Note
• This unit can be paired with up to four connecting devices. When pairing with the fifth device has succeeded, pairing data for
the device with the oldest connection date will be deleted.
• If this unit is connected via Bluetooth to another device, press and hold SOURCE to disconnect the Bluetooth connection
before you perform the pairing operation.
Bluetooth
• Bluetooth is a technology for wireless communication between devices within an area of about 10 meters (33 ft) employing
the 2.4 GHz frequency band, a band which can be used without a license.
• Bluetooth is a registered trademark of the Bluetooth SIG and is used by Yamaha in accordance with a license agreement.
Handling Bluetooth communications
• The 2.4 GHz band used by Bluetooth compatible devices is a radio band shared by many types of equipment. While
Bluetooth compatible devices use a technology minimizing the influence of other components using the same radio band,
such influence may reduce the speed or distance of communications and in some cases interrupt communications.
• The speed of signal transfer and the distance at which communication is possible differs according to the distance between
the communicating devices, the presence of obstacles, radio wave conditions and the type of equipment.
• Yamaha does not guarantee all wireless connections between this unit and devices compatible with Bluetooth function.
7 En
LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE
■ Pairing (Registration)
A Turn on the system.
B Press and hold SOURCE for more than
2 seconds to enter paring mode.
A
• Pairing mode lasts for 5 minutes.
• In paring mode, the Bluetooth indicator (
orange and blue alternately.
) will light in
B
Bluetooth indicator (
)
– If using an iPhone/iPad/iPod touch
C On your iPhone/iPad/iPod touch, turn
[Settings]
[Bluetooth] on.
C
D
TSX-B15 Yamaha
Within about 5 minutes
The Bluetooth connection list will appear in
[Devices].
(This procedure or display may differ depending
on the type of your iPhone/iPad/iPod touch.)
D From the Bluetooth connection list of the
connecting device, choose this unit
(TSX-B15 Yamaha).
• When pairing has been completed, your iPhone/iPad/
iPod touch will indicate “Connected”.
• The Bluetooth indicator ( ) will light in blue.
– If using other than an iPhone/iPad/iPod touch
C Perform Bluetooth pairing on the
connecting device.
C
For details, refer to the owner’s manual of the
connecting device.
D
TSX-B15 Yamaha
D From the Bluetooth connection list of the
connecting device, choose this unit
(TSX-B15 Yamaha).
When pairing has been completed, the Bluetooth
indicator ( ) will light in blue.
PIN 0 0 0 0
1
4
7
2
5
8
0
3
6
9
y
If you are prompted for a passkey, enter the numerals “0000”.
Within about 5 minutes
Note
Check that the pairing process on the connecting device has been completed. If the pairing process fails,
start over from step B. For details, see the connecting device’s operating instructions.
8 En
LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE
Listening to a Bluetooth device
A
A Press SOURCE to select (Bluetooth).
B Connect this unit and your connecting
device via Bluetooth.
C Play back music from your connecting
device.
Note
Take care that the volume setting of this unit is not too high. We
recommend that you adjust the volume on the connecting
device.
y
• While the system is in standby mode, if you connect a
Bluetooth device to the unit, the system will automatically
turn on.
• If you disconnect the Bluetooth connection from the
connecting device, the system will enter standby mode.
Connecting an already-paired device via Bluetooth
Once pairing with a device has been completed, connecting with that device via Bluetooth will be easy next
time.
■ Connecting from this unit
Press SOURCE to select (Bluetooth).
The Bluetooth indicator ( ) will light in orange.
This unit will search for the connecting device that was most recently connected via Bluetooth, and will then
establish a connection (You must first turn on the Bluetooth setting of the connecting device).
When the Bluetooth connection has been established, the Bluetooth indicator ( ) will light in blue.
Note
Yamaha does not guarantee all connections between this unit and Bluetooth device.
■ Connecting from the connecting device
A In the Bluetooth settings of the connecting device, turn Bluetooth on.
B From the Bluetooth connection list of the connecting device, choose this unit (TSX-B15
Yamaha).
The Bluetooth connection will be established, and the Bluetooth indicator ( ) will light in blue.
Note
Bluetooth connections cannot be established from the connecting device when this unit is in Eco Standby mode. Turn the
system on.
Disconnecting a Bluetooth connection
If any of the following operations are performed while a Bluetooth connection is established, the Bluetooth
connection will be disconnected.
• Press and hold SOURCE for more than 2 seconds.
• Press SOURCE to select a playback source other than (Bluetooth).
• Press to enter standby mode.
• Disconnect the Bluetooth connection from the Bluetooth device.
9 En
LISTENING TO EXTERNAL SOURCES
A Connect your portable audio
device to AUX using a
commercially available 3.5 mm
(1/8 in) mini plug cable.
Rear panel
A
B
C
Note
Turn down the volume of this unit and your
portable audio device before connection.
B Turn on the system.
C Press SOURCE to set the
playback source to AUX.
The AUX indicator lights.
AUX indicator
D Start playback on the connected
portable audio device.
CHARGING WITH THE USB PORT
Connecting a portable device such as a smartphone or tablet computer to the USB port on this unit charges the
connected device (power supply of up to 5 V/1 A is supported).
Prepare a USB cable that is compatible with the portable device and confirm that the device is supported for
charging via USB connection before use. In addition, read the documentation provided with the portable
device.
Rear panel
A Connect your portable device
to the USB port on this unit
using a commercially available
USB cable.
Charging automatically starts.
B Disconnect the USB cable
from the unit when charging
completes.
Check the charging status on the
portable device.
Note
USB cable from
portable device
10 En
• The USB port is for charging use only. The
USB port does not support audio playback.
• Charging may not be possible depending on
the portable device.
• In Eco Standby mode, power supply stops,
and charging is not available.
• This unit does not function as memory
storage.
• Yamaha will not be held responsible for any
damage to the portable device or data loss
occurred while using this unit.
• Disconnect the USB cable immediately after
charging completes, since power continues to
be supplied to the connected device.
TROUBLESHOOTING
Refer to the table below if the unit does not operate properly. If the problem you are experiencing is not listed
below, or if the instruction below does not help, press to enter standby mode, disconnect the power cable,
and contact the nearest authorized Yamaha dealer or service center.
General
Problem
The speakers make no
sound.
Cause
The volume may be set to the minimum
level.
Solution
Adjust the volume level.
The source may be incorrect.
Select the correct source.
The unit is setting the alarm.
Press ALARM to complete the alarm setting.
Sound suddenly turns off. Auto Standby function is enabled.
Turn on the system and play the source again.
Since the connecting device outputs at a
very low volume, the Auto Standby
function is enabled.
Raise the volume of the connecting device.
Sound is cracked/
distorted or there is
abnormal noise.
Input source volume is excessive, or
volume of this unit is excessive.
Adjust the volume with VOLUME.
The unit does not operate
properly.
The unit may have received a strong
electrical shock such as lightning or
excessive static electricity, or power
supply may have dropped.
Press
to enter standby mode and
disconnect the power cable. Wait about
30 seconds, reconnect the power cable, and
turn on the system.
The system turns on but
immediately shuts off.
The power cable may be connected
improperly.
Make sure the power cable is plugged into the
wall outlet firmly.
The unit may have received a strong
electrical shock such as lightning or
excessive static electricity.
Disconnect the power cable. Wait about
30 seconds, reconnect the power cable, and
turn on the system.
A digital or high-frequency The unit may be placed too close to the
digital or high-frequency equipment.
equipment produces
noises.
Place the unit farther away from the
equipment.
The clock setting has been The unit is left more than one week after
you disconnect the power cable from the
cleared.
Plug the power cable into the wall outlet
firmly, and set the clock again (☞ page 4).
wall outlet.
The clock flashes.
The unit is setting CLOCK or ALARM.
Press
to cancel setting CLOCK or
ALARM.
FM radio reception
Problem
Too much noise during
stereo broadcast.
Cause
Solution
The radio station you selected may be far Try manual tuning to improve the signal
from your area, or the radio wave
quality (☞ page 6) or change the height or
reception is weak in your area.
direction of the antenna, or relocate the unit
(☞ page 3).
11 En
TROUBLESHOOTING
Bluetooth
Problem
Cause
Solution
The connecting device does not support
Perform pairing operations with a device
Cannot make this unit
which supports A2DP.
paired with the connecting A2DP.
The passkey of the connecting device that Use a connecting device with a passkey
device.
you want to pair with this unit is a passkey
other than “0000”.
This unit and the connecting device are
too far apart.
There is a device (microwave oven,
wireless LAN, etc.) that outputs signals in
the 2.4 GHz frequency band nearby.
The unit is in standby mode.
Another Bluetooth device is connected.
Cannot establish a
Bluetooth connection.
No sound is produced or
the sound is interrupted
during playback.
“0000”.
Move the connecting device closer to this
unit.
Move this unit away from the device that is
emitting radio-frequency signals.
Turn the unit on and perform paring (☞ page 8).
Terminate current Bluetooth connection, and
perform pairing with the new device.
This unit is not registered on the connecting Perform pairing operations again (☞ page 7).
device’s Bluetooth connection list.
The unit is in Eco Standby mode.
Turn the unit on, then establish a Bluetooth
connection (☞ page 9).
Another Bluetooth device is connected.
Terminate current Bluetooth connection, then
establish a Bluetooth connection with that
device again.
The Bluetooth function of the device is
Turn on the Bluetooth function of the device.
turned off.
The pairing information has been deleted. Perform pairing again (☞ page 7).
This unit can be paired with four devices. If
pairing with the fifth device is performed, the
pairing information with the earliest
connection date will be deleted.
Delete any pairing history of TSX-B15 on the
iPhone/iPad/iPod touch, then pair with the
TSX-B15 again (☞ page 8).
The Bluetooth connection of this unit with Perform Bluetooth connection operations
the connecting device is disconnected.
again (☞ page 9).
This unit and the connecting device are
Move the connecting device closer to this
too far apart.
unit.
There is a device (microwave oven,
Move this unit away from the device that is
wireless LAN, etc.) that outputs signals in emitting radio-frequency signals.
the 2.4 GHz frequency band nearby.
The connecting device’s Bluetooth
Turn on the Bluetooth function of the
function is off.
connecting device.
The connecting device is not set to send Check that the Bluetooth function of the
Bluetooth audio signals to this unit.
connecting device is set properly.
The pairing setting of the connecting
Set the pairing setting of the connecting
device is not set to this unit.
device to this unit.
The connecting device’s volume is set to Increase the volume level.
the minimum.
The connecting device is connected to
Select this unit as a playback device for the
more than two Bluetooth speakers and this connecting device.
unit (TSX-B15) is not selected as a
playback device.
USB port charging
Problem
Cannot charge the
connected portable USB
device.
12 En
Cause
Solution
An incompatible USB device is connected Press
to enter standby mode, and reconnect
to the unit. Or the USB device is not
the USB device to the unit. If it does not
connected to this unit properly.
resolve the problem, the USB device is not
chargeable with the unit.
SPECIFICATIONS
■ PLAYER SECTION
■ GENERAL
AUX IN
• Power Supply............................ AC 100 to 240 V 50/60 Hz
• Power consumption .....................................................11 W
• Standby consumption
(Clock displayed, Bluetooth ready for connection) ....1.0 W
• Eco Standby consumption ..........................................0.2 W
• Time of power management (Auto Standby)
................................................ No sound: about 20 minutes
.................................................No operation: about 8 hours
• Weight......................................................... 0.9 kg (2.0 lbs.)
• Dimensions
• Input connector
............STEREO L/R: 3.5 mm (1/8 in) STEREO mini Jack
■ AMPLIFIER SECTION
• Driver unit .........................5 cm (2 in) full-range driver × 2
■ Bluetooth SECTION
•
•
•
•
•
Bluetooth version.....................................................Ver. 3.0
Supported protocols.................................................... A2DP
Supported codecs.......................................................... SBC
Wireless output.........................................Bluetooth Class 2
Maximum communication distance
...................................... 10 m (33 ft) (without obstructions)
• Supported contents protection .................. SCMS-T method
180 mm (7-1/8 in)
200 mm (7-7/8 in)
100 mm
(3-7/8 in)
■ TUNER SECTION
• Tuning range (FM) .................................87.5 to 108.0 MHz
■ CHARGING CONNECTOR SECTION
• Connector type ................................................. USB type A
• Output rating............................................................ 5 V/1 A
iPad, iPhone, and iPod touch are trademarks of Apple
Inc., registered in the U.S. and other countries.
■ For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
Specifications are subject to change without notice.
■ Special Instructions for U.K.
Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured BLUE must be connected
to the terminal which is marked with the letter N or
coloured BLACK. The wire which is coloured
BROWN must be connected to the terminal which is
marked with the letter L or coloured RED.
Make sure that neither core is connected to the earth
terminal of the three pin plug.
AVEEA71102B
Important Notice: Guarantee Information for customers in EEA* and Switzerland
English
For detailed guarantee information about this Yamaha product, and Pan-EEA* and Switzerland warranty service, please
either visit the website address below (Printable file is available at our website) or contact the Yamaha representative
office for your country. * EEA: European Economic Area
http://europe.yamaha.com/warranty/
13 En
© 2014 Yamaha Corporation
Printed in China ZN35300