Sharp AL-2050 Specifications

ED IN CHINA
2008A
KS1
TINSE1865QSZZ
!000-Cover1.fm
1 ページ
2008年1月11日 金曜日 午後1時1分
MODEL
AL-2050CS
DIGITAL MULTIFUNCTIONAL
SYSTEM
OPERATION MANUAL
(for general information)
Page
PREPARATIONS
LOADING PAPER
MAKING COPIES
9
18
24
CONVENIENT COPY
FUNCTIONS
30
INSTALLING THE
SOFTWARE
40
PRINTER/SCANNER
FUNCTIONS
57
USER SETTINGS
62
TROUBLESHOOTING AND
MAINTENANCE
69
APPENDIX
91
!AL-2050CS.book
0 ページ
2008年1月7日 月曜日 午後8時10分
FOR YOUR PROTECTION...
To aid in reporting this unit in case of loss or theft, please record below the model number
and serial number located on the back of the unit. We also suggest you record all the
information listed and retain for future reference.
MODEL NUMBER
SERIAL NUMBER
DATE OF PURCHASE
Dealer
Address
City
State
Zip
Telephone
Service Station
Address
State
City
Zip
Telephone
To obtain service, or to obtain product literature, accessories, or
supplies,
please call 1-(630)378-3590 in the USA.
For customer assistance, please visit http://www.sharpusa.com/
(for USA) on the World Wide Web or call 1-(630)378-3590 (for USA).
Shielded interface cables must be used with this equipment to maintain
compliance with EMC regulations.
Do not make copies of anything which is prohibited from copying by law. The
following items are normally prohibited from copying by national law. Other
items may be prohibited by local law.
Money
Stamps
Bonds
Stocks
Bank drafts
Checks
Passports
Driver's licenses
!AL-2050CS.book
1 ページ
2008年1月7日 月曜日 午後8時10分
CONTENTS
CAUTIONS ................................................................................................................ 3
SOFTWARE LICENSE .............................................................................................. 4
ENVIRONMENTAL INFORMATION .......................................................................... 5
INTRODUCTION ....................................................................................................... 6
MAIN FEATURES...................................................................................................... 7
1 PREPARATIONS
PART NAMES.................................................................................................... 9
CHECKING PACKED COMPONENTS AND ACCESSORIES ........................ 12
PREPARING THE MACHINE FOR INSTALLATION........................................ 12
INSTALLING THE TD (TONER/DEVELOPER) CARTRIDGE ......................... 14
POWER ON AND OFF .................................................................................... 16
2 LOADING PAPER
PAPER............................................................................................................. 18
LOADING THE PAPER TRAY ......................................................................... 19
BYPASS FEED (including special paper) ........................................................ 21
CHANGING A TRAY'S PAPER SIZE SETTING .............................................. 23
3 MAKING COPIES
NORMAL COPYING........................................................................................ 24
SELECTING THE TRAY.................................................................................. 27
MAKING A COPY DARKER OR LIGHTER ..................................................... 28
REDUCTION/ENLARGEMENT/ZOOM ........................................................... 29
4 CONVENIENT COPY FUNCTIONS
AUTOMATIC TWO-SIDED COPYING ............................................................. 30
SORT COPY ................................................................................................... 33
COPYING MULTIPLE ORIGINALS ONTO A SINGLE SHEET OF PAPER
(2 IN 1 copy) .................................................................................................... 35
CREATING MARGINS WHEN COPYING (Margin shift) ................................. 38
5 INSTALLING THE SOFTWARE
SOFTWARE .................................................................................................... 40
BEFORE INSTALLATION ................................................................................ 41
INSTALLING THE SOFTWARE....................................................................... 42
SETTING UP BUTTON MANAGER ................................................................ 53
1
!AL-2050CS.book
2 ページ
2008年1月7日 月曜日 午後8時10分
6 PRINTER/SCANNER FUNCTIONS
USING THE PRINTER MODE ........................................................................ 58
BASIC PROCEDURE FOR PRINTING ........................................................... 58
USING THE SCANNER MODE....................................................................... 59
SCANNING USING THE KEYS ON THE MACHINE ...................................... 59
SCANNING FROM YOUR COMPUTER ......................................................... 60
OPERATION IN COPY, PRINTER, AND SCANNER MODES ........................ 60
HOW TO USE THE ONLINE MANUAL ........................................................... 61
7 USER SETTINGS
USER PROGRAMS......................................................................................... 62
SELECTING A SETTING FOR A USER PROGRAM...................................... 67
8 TROUBLESHOOTING AND MAINTENANCE
DISPLAY MESSAGES..................................................................................... 69
TROUBLESHOOTING THE MACHINE ........................................................... 71
PROBLEMS DURING SETUP OF THE SOFTWARE ..................................... 75
MISFEED REMOVAL ...................................................................................... 78
TD (TONER/DEVELOPER) CARTRIDGE REPLACEMENT ........................... 82
DRUM CARTRIDGE REPLACEMENT ............................................................ 84
CHECKING THE TOTAL COUNT AND DRUM CARTRIDGE LIFE................. 86
CLEANING THE MACHINE ............................................................................ 87
ABOUT SUPPLIES AND OPTIONS................................................................ 90
9 APPENDIX
SPECIFICATIONS ........................................................................................... 91
IMPORTANT SERVICE INFORMATION (U.S.A. only) .................................... 95
END-USER LIMITED WARRANTY (Valid in U.S.A. only) ............................... 96
MATERIAL SAFETY DATA SHEET ................................................................. 98
INDEX............................................................................................................ 106
2
!AL-2050CS.book
3 ページ
2008年1月7日 月曜日 午後8時10分
CAUTIONS
Caution label on the machine
The label (
) in the fusing area of the machine indicates the following:
: Caution, risk of danger
: Caution, hot surface
Cautions on using the machine
Follow the cautions below when using this machine.
Warning:
• The fusing area is hot. Exercise care in this area when removing misfed paper.
• Do not look directly at the light source. Doing so may damage your eyes.
Caution:
• Place the machine on a firm, level surface.
• Do not install the machine in a humid or dusty location.
• When the machine is not used for a long time, for example during prolonged
holidays, turn the power switch off and remove the power cord from the outlet.
• When moving the machine, be sure to turn the power switch off and remove the
power cord from the outlet.
• Do not switch the machine rapidly on and off. After turning the machine off, wait 10
to 15 seconds before turning it back on.
• Do not cover the machine with a dust cover, cloth or plastic film while the power is
on. Doing so may prevent heat radiation, damaging the machine.
• Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
• The socket-outlet shall be installed near the machine and shall be easily
accessible.
Important points when selecting an installation site
Do not install your machine in areas that are:
• damp, humid, or very dusty
• exposed to direct sunlight
• poorly ventilated
• subject to extreme temperature or humidity changes, e.g., near an air conditioner
or heater.
Be sure to allow the required space around the
8" (20 cm)
machine for servicing and proper ventilation.
4"
(10 cm)
4"
(10 cm)
3
!AL-2050CS.book
4 ページ
2008年1月7日 月曜日 午後8時10分
Cautions on handling the machine
Be careful in handling the machine as follows to maintain the performance of this
machine.
Do not drop the machine, subject it to shock or strike it against any object.
Do not expose the drum cartridge to direct sunlight.
• Doing so will damage the surface (green portion) of the drum cartridge, causing
smudges on copies.
Store spare supplies such as drum cartridges and TD (Toner/Developer)
cartridges in a cool dry place without removing from the package before use.
• If they are exposed to direct sunlight, or excessive heat, poor copies may result.
Do not touch the surface (green portion) of the drum cartridge.
• Scratches or smudges on the drum will cause dirty copies.
Supply and Consumables
The supply of spare parts for a repair of the appliance is guaranteed for at least 7
years following the termination of production. Spare parts are those parts of the
apparatus which may break down within the scope of ordinary use of the product,
whereas those parts which normally exceed the life of the product are not
considered spare parts. Consumables also, are available for 7 years following the
termination of production.
Trademark acknowledgements
• Microsoft®, Windows®, Windows® 98, Windows® Me, Windows® 2000,
Windows® XP, Windows Vista® and Internet Explorer® are registered trademarks
or trademarks of Microsoft Corporation in the U.S.A. and other countries.
• Macintosh is a trademark of Apple Inc., registered in the U.S. and other countries.
• IBM, PC/AT, and PowerPC are trademarks of International Business Machines
Corporation.
• Adobe, the Adobe logo, Acrobat, the Adobe PDF logo, and Reader are registered
trademarks or trademarks of Adobe Systems Incorporated in the United States
and other countries.
• Sharpdesk is a trademark of Sharp Corporation.
• All other trademarks and copyrights are the property of their respective owners.
SOFTWARE LICENSE
The SOFTWARE LICENSE will appear when you install the software from the CDROM. By using all or any portion of the software on the CD-ROM or in the machine,
you are agreeing to be bound by the terms of the SOFTWARE LICENSE.
4
!AL-2050CS.book
5 ページ
2008年1月7日 月曜日 午後8時10分
ENVIRONMENTAL INFORMATION
For users in the USA
Products that have earned the ENERGY STAR® are designed to
protect the environment through superior energy efficiency.
Laser information
Wave length
780 nm
Pulse times (North America)
Output power
+15 nm
-10 nm
12.88 µs ±12.88 ns/7 mm
Max 0.2 mW
At the production line, the output power of the scanner unit is adjusted to 0.18
MILLIWATT PLUS 5% and is maintained constant by the operation of the
Automatic Power Control (APC).
Caution
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 1.2-2001)
SAFETY PRECAUTIONS
This Digital Copier is rated Class 1 and complies with 21 CFR 1040.10 and
1040.11 of the CDRH standards. This means that the equipment does not produce
hazardous laser radiation. For your safety, observe the precautions below.
• Do not remove the cabinet, operation panel or any other covers.
• The equipment's exterior covers contain several safety interlock switches. Do not
bypass any safety interlock by inserting wedges or other items into switch slots.
A small amount of ozone is produced within the unit during operation. The
emission level is insufficient to cause any health hazard.
Note:
The present recommended long term exposure limit for ozone is 0.1ppm
(0.2mg/m3) calculated as an 8 hr. time-weighted average concentration.
However, since the small amount that is emitted may have an objectionable odor, it
is advisable to place the unit in a ventilated area.
5
!AL-2050CS.book
6 ページ
2008年1月7日 月曜日 午後8時10分
INTRODUCTION
Note
Some model may not be available in some countries.
Using the manual
This machine has been designed to provide convenient copying features in a
minimum amount of office space and with maximum operational ease. To get full use
of all machine features, be sure to familiarize yourself with this manual and the
machine. For quick reference during machine use, keep this manual in a handy
location.
About the operation manuals
The operation manuals for the machine are as follows:
Operation Manual (this manual)
Explains the machine and how to use it as a copier. Also explains how to install the
software that allows the machine to be used as a printer and scanner for your
computer.
Online Manual (on the accessory CD-ROM)
This manual explains the procedures for using the machine as a printer or a
scanner.
Conventions used in this manual and online manual
• Where "AL-XXXX" appears in this manual, please substitute the name of your
model for "XXXX". For the name of your model, see the operation panel on the
machine.
• Illustrations of driver screens and other computer screens show the screens that
appear in Windows XP Home Edition. Some of the names that appear in these
illustrations may differ slightly from the screens that appear in other operating systems.
• The explanations in this manual assume that the person who will install the product and
the users of the product have a working knowledge of Microsoft Windows.
• This operation manual refers to the Reversing Single Pass Feeder as the "RSPF".
• In this manual, the following icons are used to provide the user with information
pertinent to the use of the machine.
Warns that injury may result if the contents of the warning are
Warning not properly followed.
Cautions that damage to the machine or one of its components may
Caution result if the contents of the caution are not properly followed.
Note
Notes provide useful information on the specifications, functions,
performance, and operation of the machine.
The display screens, messages, and key names shown in the manual may differ
from those on the actual machine due to product improvements and modifications.
6
!AL-2050CS.book
7 ページ
2008年1月7日 月曜日 午後8時10分
MAIN FEATURES
High-speed laser copying
First-copy time*1 is only 8.0*2 seconds.
Copying speed is 20 copies per minute. This is ideal for business use and provides a
big boost to workplace productivity.
*1 The first-copy time is measured after the power save indicator turns off following
power on, using the document glass with the polygon rotating in the copy ready state
and "LSU SETTING" set to ON in the user programs (8-1/2" x 11", paper fed from
paper tray).
*2 When user program 24 is set to OFF.
High-quality digital image
• High-quality copying at 600 dpi is performed.
• In addition to automatic exposure adjustment, two original modes can be selected:
"TEXT" for text-only originals, and "PHOTO" for photographs. The exposure can be
adjusted to five levels in each mode.
• The photo mode copying function allows clear copying of delicate halftone original
images such as monochrome photos and color photos.
Enhanced copying features
• Zoom copies can be made from 25% to 400% in increments of 1%. (When the
RSPF is being used, the zoom copy ratio range is 50% to 200%.)
• Continuous copying of up to 99 copies is possible.
• Sets of output can be offset from each other for easy separation (offset function).
• Sorting by sets is possible without the need for a sorter or other special device
(Sort copy).
• Includes convenient features such as margin shift, 2 IN 1 copy, and automatic twosided copying.
1 2 3
2
3
1 2 3
1
1
2
3
1 1
1 2 3
A
Sort copy
Offset function
2 IN 1 copy
A
Margin shift
Scan once/Print many
• The machine is equipped with a memory buffer allowing the machine to scan an
original once and make up to 99 copies of the scanned image. This improves
workflow, reduces operating noise from the machine and reduces wear and tear on
the scanning mechanism, which provides for a higher reliability.
7
!AL-2050CS.book
8 ページ
2008年1月7日 月曜日 午後8時10分
LCD panel displays messages
• The LCD panel displays messages that show function settings and the status of
the machine.
Laser printer function
• Printer function
The accompanying printer driver can be installed to enable use of the machine as
a printer.
• Network printer function
A LAN connector is provided as a standard feature that allows the machine to be
used as a network printer.
Color scanner function
• The accompanying scanner driver can be installed and the machine connected to
a computer using a USB cable to enable use as a scanner.
Environment and people friendly design
• Preheat mode and auto power shut-off mode are provided to reduce power
consumption when the machine is not in use.
• A universal design has been implemented in the product whereby the height of the
operation panel and shape of the keys are designed to be usable by as many
people as possible.
8
!AL-2050CS.book
1
9 ページ
2008年1月7日 月曜日 午後8時10分
Chapter 1
PREPARATIONS
This chapter provides basic information that you should know before using the machine.
1
PART NAMES
RSPF
Original guides
Document
feeder cover
1
Exit area
2
Document feeder tray
5
6
7
3
4
Bypass tray
17
Interface
USB
connector
TD (Toner/Developer)
cartridge
Drum cartridge
LAN
connector
8
5
9
10
14
11
12
1
2
3
4
5
6
7
8
9
12
3
13
Document glass
Operation panel
Front cover
Paper trays
Side cover
Side cover open button
Bypass tray paper guides
Original output tray extension
Paper output tray
15
16
10
11
12
13
14
15
16
17
Paper output tray extension
Power switch
Handles
Power cord
Fusing unit release lever
Transfer charger
Charger cleaner
Paper holder arm
9
!AL-2050CS.book
10 ページ
2008年1月7日 月曜日 午後8時10分
PREPARATIONS
Operation panel
1
2
6 7
1 [MODE SELECT] key / Mode indicators
2
3
4
5
6
7
7
10
Press this key to select the mode. The
indicator of the selected mode lights (copy,
printer, scanner indicators).
Display
This shows messages indicating the
machine status and any problems that
occur, as well as user programs and
function setting menus.
Numeric keys
Use these to enter the number of copies
and other numerical settings.
The keys can also be used to select
items in function setting menus.
[CLEAR] key (
)
Use this to clear the set number of
copies, as well as cancel a job that is in
progress. When a setting menu appears,
use this key to move back to the
previous menu level.
Power save indicator
This lights up when the power save
function is activated.
RSPF indicator
This lights up when an original is placed
in the RSPF.
Error indicator
This lights steadily or blinks when a
paper misfeed or other error occurs.
8
9
10
11
11
12
12
13
13
14
8 9 10 11
12 13 14
15
[TRAY SELECT] key (
)
Use to select the paper tray that has the
desired paper for copying.
Tray location indicator
Indicates the selected paper tray. The
indicator blinks when the tray is out of paper
during operation or is not closed properly.
[MENU] key
Press this key to select the paper size for
copying, to configure a user program or
to display the total count.
[2-SIDED COPY] key
Press to select the automatic two-sided
copying mode.
[E-SORT/SP.FUN] key
Press to select the sort function, 2 IN 1
copy function, or margin shift function.
[
] key (
), [
] key (
),
[ENTER] key
Press the [
] key (
) or [
] key
(
) to select an item in a function
setting menu.
Press the [ENTER] key to enter a selection.
[EXPOSURE] key
Use to switch from auto exposure
adjustment to text mode or photo mode.
!AL-2050CS.book
11 ページ
2008年1月7日 月曜日 午後8時10分
PREPARATIONS
3
4
5
1
Display
READY TO COPY.
100% 8.5x11
18
16
15
15
19
0
20
21
17
[COPY RATIO] key
Press to select an enlargement or
reduction ratio.
To select a preset ratio setting, press the
[COPY RATIO] key and select the
desired preset ratio. To select a ratio
that is not preset, press the [COPY
RATIO] key, select the preset ratio that
is closest to the desired ratio, and then
] key
press the [
] key (
) or [
(
) to increase or decrease the ratio in
increments of 1%.
17 [CLEAR ALL] key (
16
)
This returns all functions to the default
settings. When pressed in a setting
menu, this returns the settings and
display to the initial state.
17 [START] key (
16
) / Ready indicator
The ready indicator lights up when
copying or scanning is possible.
To begin copying, press the [START]
key (
).
The [START] key (
) is also pressed
to return to normal operation from auto
power shut-off mode.
18 Shows the current copy ratio.
19 Shows the selected paper size.
20 Shows the number of copies that has
been entered with the numeric keys.
" appears when the
exposure has been changed, or when
two-sided copying, sort, 2 IN 1, or
margin shift is selected.
21 A checkmark "
11
!AL-2050CS.book
12 ページ
2008年1月7日 月曜日 午後8時10分
CHECKING PACKED COMPONENTS AND
ACCESSORIES
Open the carton and check if the following components and accessories are included.
If anything is missing or damaged, contact our Technical Assistance Department at
1-(630)378-3590 in the USA.
Note
If the machine does not function properly during setup or use, or if a
function cannot be used, see "TROUBLESHOOTING AND
MAINTENANCE" (p.69).
Operation manual
Software CD-ROM
Drum cartridge
(installed in machine)
TD cartridge
(Toner/Developer cartridge)
PREPARING THE MACHINE FOR INSTALLATION
1
12
Be sure to hold the handles on
both sides of the machine to
unpack the machine and carry it to
the installation location.
!AL-2050CS.book
13 ページ
2008年1月7日 月曜日 午後8時10分
PREPARATIONS
2
Remove all pieces of tape shown in the illustration below and
then open the RSPF and remove protective materials. Take out
the bag containing the TD (Toner/Developer) cartridge.
1
3
Release the scan head locking switch.
The scan head locking switch is under the document glass.
If the switch is locked ( ), the machine will not operate. Unlock the switch
(
) as shown below.
Grasp here and turn in
the direction of the arrow.
A
Lock
Unlock
To lock the scan head locking switch, hold up the catch in illustration A and
turn the center knob counter-clockwise 90 degrees until you hear a click.
13
!AL-2050CS.book
14 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE TD (TONER/DEVELOPER) CARTRIDGE
1
Open the bypass tray, and
then open the side cover.
2
Remove the CAUTION tape from the front cover and remove the
two protective pins from the fusing machine by pulling the
strings upward one at a time.
Protective pins
CAUTION tape
3
Press gently on both sides of
the front cover to open the
cover.
4
Remove the TD (Toner/Developer) cartridge from the bag. Remove
the protective paper. Hold the cartridge on both sides and shake it
horizontally four or five times. Hold the tab of the protective cover
and pull the tab to your side to remove the cover.
4 or 5 times
14
!AL-2050CS.book
15 ページ
2008年1月7日 月曜日 午後8時10分
PREPARATIONS
5
While pushing the lock release
button, gently insert the TD
(Toner/Developer) cartridge until
it locks into place.
Lock release button
1
6
Close the front cover and then
the side cover by pressing the
round projections near the
side cover open button.
When closing the covers, be
Note sure to close the front cover
securely and then close the side
cover. If the covers are closed in
the wrong order, the covers may
be damaged.
7
Ensure that the power switch of the machine is in the OFF
position. Plug the other end of the power cord into the nearest
outlet.
15
!AL-2050CS.book
16 ページ
2008年1月7日 月曜日 午後8時10分
POWER ON AND OFF
The power switch is located on the left side of the machine.
If you use the machine in a country other than the country
Warning where the machine was purchased, you will need to make sure
that your local power supply is compatible with your model. If
you plug the machine into an incompatible power supply,
irreparable damage to the machine will result.
Power on
Turn the power switch to the "ON" position.
The ready indicator will light up and other indicators
which show the initial settings of the display will also
light up to indicate the ready condition. For the initial
settings, see "Initial settings" (below).
You can select copy settings and press the [START] key (
switch is turned on. Copying will start automatically.
) after the power
Only insert the power cord into a properly grounded wall socket.
Caution Do not use extension cords or power strips.
Language setting
The first time the power is turned on after shipment from the factory, a message will
appear in English in the display prompting you to select the language. Select the
language with the [
] key (
) or [
] key (
) and then press the [ENTER] key.
The language can also be changed in the user programs (p.65).
Initial settings
The machine reverts to the initial settings when it is first turned on, when the [CLEAR
ALL] key (
) is pressed, or when no keys are pressed for the preset "AUTO
CLEAR" time following the end of a copy job. When the machine reverts to the initial
settings, all settings and functions selected to that point are canceled. The "AUTO
CLEAR" can be changed in the user programs. (p.62)
When in the copy mode
READY TO COPY.
100% 8.5x11
0
The main screen of copy mode appears.
Copy ratio: 100%, Exposure: Automatic
Copy quantity: 0, All special copier modes: Off
Scanning unit (scan head)
When the machine is able to copy or scan (the ready indicator is on), the scanning
unit is lit.
16
!001-Introduction.fm
17 ページ
2008年5月23日 金曜日 午後2時29分
PREPARATIONS
Power off
Make sure that the machine is not in operation and then turn the power
switch to the "OFF" position.
If the power switch is turned off while the machine is
in operation, a misfeed may occur and the job that
was in progress will be canceled.
In cases where the machine will not be used for a
long time, turn off the power switch and remove the
power cord from the outlet.
1
Check the following to make sure the machine is not in operation:
• The ready indicator is lit. (Initial state)
• The power save indicator is lit. (preheat mode or auto power shut-off mode)
Power save modes
The machine has two power save modes to reduce overall power consumption and
thereby reduce the cost of operation. In addition, these modes conserve natural
resources and help reduce environmental pollution. The two power save modes are
preheat mode and auto power shut-off mode.
Preheat mode
This function automatically switches the machine to a low power consumption state if
the set duration of time elapses without the machine being used when the power is
on. In this mode, the power save indicator lights up. Normal operation automatically
resumes when a key on the operation panel is pressed, an original is placed, a print
job is received.
Auto power shut-off mode
This function automatically switches the machine to a state that consumes even less
power than preheat mode if the set duration of time elapses without the machine being
used when the power is on. The power save indicator lights up, the display shows a
message indicating that the machine is in auto power shut-off mode. To resume normal
operation, press the [START] key (
). Normal operation also resumes automatically
when a print job is received or scanning is begun from a computer. While in auto power
shut-off mode, no keys (except the [START] key (
)) can be used.
Note
The preheat activation time and the auto power shut-off time can be
changed with "PREHEAT MODE" and "AUTO SHUT-OFF TIME" in the
user programs. It is suggested that you set times that are appropriate
for your usage of the machine. (p.62 and p.63)
17
!AL-2050CS.book
2
18 ページ
2008年1月7日 月曜日 午後8時10分
Chapter 2
LOADING PAPER
The tray location indicator will blink when there is no paper in the selected paper
tray, or when the selected paper tray is not closed or is improperly closed.
PAPER
For best results, use only SHARP recommended paper.
Paper tray type
Paper type
Size
Weight
Capacity
Paper tray
15 lbs. to 21 lbs.
Standard paper 5-1/2" x 8-1/2"
(56 g/m2 to
Recycled paper (Invoice)
8-1/2" x 11" (Letter) 80 g/m2)
8-1/2" x 13"
(Foolscap)
8-1/2" x 14" (Legal)
250 sheets *1
(The paper
should not
exceed the
line on the
tray)
Bypass tray
Standard paper 3-1/2" x 5-1/2" to
Recycled paper 8-1/2" x 14"
15 lbs. to 21 lbs.
(56 g/m2 to
80 g/m2)
50 sheets *1
Thick paper
15 lbs. to 34.5 lbs. Load one
(56 g/m2 to
sheet at a
time in the
128 g/m2)*3
bypass tray.
Transparency
film/Labels
Envelopes *2
Monarch
(3-7/8" x 7-1/2")
Commercial 9
(3-7/8" x 8-7/8")
Commercial 10
(4-1/8" x 9-1/2")
*1 The number of sheets of paper that can be loaded varies depending on the weight of
the paper.
*2 Do not use non-standard envelopes or envelopes that have metal clasps, plastic
snappers, strings, windows, linings, self-adhesive strips, patches or synthetic materials.
Do not use envelopes that are filled with air or envelopes that have labels or stamps
attached. These will damage the machine.
*3 When using paper heavier than 28 lbs. (104 g/m2), use paper that is 8-1/2" x 11" or
smaller.
18
!AL-2050CS.book
19 ページ
2008年1月7日 月曜日 午後8時10分
LOADING PAPER
Special papers
Follow these guidelines when using special papers.
● Use SHARP recommended transparency film and label sheets. Using other
than SHARP recommended paper may result in misfeeds or smudges on
the output. If other than SHARP recommended media must be used, feed
each sheet one at a time using the bypass tray (do not attempt continuous
copying or printing).
● There are many varieties of special paper available on the market, and
some cannot be used with this machine. Before using special paper,
contact a SHARP service center.
● Before using other than SHARP recommended paper, make a test copy to
see if the paper is suitable.
2
LOADING THE PAPER TRAY
Note
Make sure that the paper is not torn, is free of dust, and has no wrinkles
or curled edges.
1
Raise the handle of the paper tray
and pull the paper tray out until it
stops.
2
Remove the pressure plate lock. Rotate the pressure plate lock
in the direction of the arrow to remove it while pressing down
the pressure plate of the paper tray.
19
!AL-2050CS.book
20 ページ
2008年1月7日 月曜日 午後8時10分
LOADING PAPER
3
Store the pressure plate lock which has been removed in step
2. To store the pressure plate lock, rotate the lock to secure it
as shown below.
Pressure plate lock
4
Fan the paper and insert it into the tray. Make sure that the
edges go under the corner hooks.
Note
5
Gently push the paper tray back into the machine.
Note
20
• Do not load paper above the maximum height line (
).
Exceeding the line will cause a paper misfeed.
• If the paper is not fanned, double-feeds or misfeeds may occur.
• Make sure the stack of paper is straight before loading it. When
adding paper, take the remaining paper out and combine it into a
single stack with the new paper.
• Make sure that all the paper in the stack is the same size and type.
• When loading paper, ensure that there is no space between the
paper and the guide, and make sure that the guide is not set too
narrow and causes the paper to bend. Incorrect loading will cause the
paper to skew or misfeed.
• If you loaded a paper size that is different from the previously loaded
paper size, change the paper size setting as explained in
"CHANGING A TRAY'S PAPER SIZE SETTING" (p.23)
• When not using the machine for an extended period, remove all
paper from the paper tray and store it in a dry place. If paper is left in
the machine for an extended period, the paper will absorb moisture
from the air, resulting in paper jams.
!AL-2050CS.book
21 ページ
2008年1月7日 月曜日 午後8時10分
BYPASS FEED (including special paper)
The bypass tray can be used to feed standard paper, transparency film, labels,
envelopes, and other special purpose paper.
Important points when inserting paper in the bypass tray
Up to 50 sheets of standard copy paper can be inserted in the bypass tray. (Capacity
will vary depending on the type of paper loaded.)
Be sure to place envelopes horizontally as shown in the following diagram.
2
Not
Available
When loading envelopes, make sure that they are straight and flat and do not have
loosely glued construction flaps (not the closure flap).
Special papers such as SHARP recommended transparency film, labels, and
envelopes must be fed one sheet at a time through the bypass tray.
When adding paper, first remove any paper remaining in the tray, combine it with
the paper to be added and then reload as a single stack. The paper to be added
must be the same size and type as the paper already in the tray.
Do not use paper that is smaller than the original. This may cause smudges or
unclean images.
Do not use paper that has already been printed on by a laser printer or plain paper
fax machine. This may cause smudges or unclean images.
Available
•
•
•
•
•
Envelopes
Do not use the following envelopes, as misfeeds will occur.
• Envelopes with metal tabs, clasps, strings, holes, or windows.
• Envelopes with rough fibers, carbon paper, or glossy surfaces.
• Envelopes with two or more flaps.
• Envelopes with tape, film, or paper attached to the flap.
• Envelopes with a fold in the flap.
• Envelopes with glue on the flap to be moistened for sealing.
• Envelopes with labels or stamps.
• Envelopes that are slightly inflated with air.
• Envelopes with glue protruding from the seal area.
• Envelopes with part of the seal area peeled off.
• Be sure to select com9, com10 or Monarch in the paper size setting of the printer
driver. (For detailed information on the printer driver, refer to the online manual.)
21
!AL-2050CS.book
22 ページ
2008年3月18日 火曜日 午後7時40分
LOADING PAPER
Loading paper in the bypass tray
Note
1
• Paper must be fed narrow side first into the feed slot.
• Special papers such as transparency film, labels, and envelopes
must be fed one sheet at a time through the bypass tray.
• When copying onto transparency film, remove each copy promptly.
Do not let copies stack up.
Open the bypass tray and extend the tray.
Note
To close the bypass tray, perform step 1 and then step 2 in the
illustration and push the round projections at the right of the tray
until they click.
2
1
2
Set the bypass tray paper guides to the paper width. Insert the
paper (print face down) all the way into the bypass tray.
Print face
3
Press the [TRAY SELECT] key (
) to select the bypass tray.
Note for loading thick paper
Confirm that user program 29 is set to "2 (HEAVY PAPER)" when using thick
paper. (See page 65.)
22
!AL-2050CS.book
23 ページ
2008年1月7日 月曜日 午後8時10分
CHANGING A TRAY'S PAPER SIZE SETTING
Follow these steps to change a tray's paper size setting.
Note
• The paper size setting cannot be changed when the machine has
stopped temporarily due to running out of paper or a misfeed.
• During printing (even in copy mode), the paper size setting cannot be
changed.
1
Press the [MENU] key.
Press the [ ] key ( ) or [ ] key ( ) until "PAPER SIZE"
appears, and then press the [ENTER] key.
2
Press the [ ] key ( ) or [ ] key (
select the tray, and then press the
[ENTER] key.
3
Press the [ ] key ( ) or [ ] key ( ) to
select the paper size, and then press the
[ENTER] key.
) to
PAPER SIZE
1:TRAY1
2
TRAY1
1:8.5X14
The paper size changes as follows each time the
[
] key (
) or [
] key (
) is pressed:
"8.5x14"→"8.5x13"→"8.5x11"→"5.5x8.5"
→"A4"→"B5"→"A5".
Note
4
When you have finished configuring the tray's paper size setting,
press the [MENU] key.
Squeeze the lock lever of the front guide and slide the front
guide to match the width of the paper, and move the left guide
to the appropriate slot as marked on the tray.
Left
guide
Front
guide
• The front guide is a slide-type guide. Grasp the locking knob on the guide
and slide the guide to the indicator line of the paper to be loaded.
• The left guide is an insert-type guide. Remove it and then insert it at the
indicator line of the paper to be loaded.
23
!003-making copies.fm 24 ページ
3
2008年5月23日 金曜日 午後2時30分
Chapter 3
MAKING COPIES
This chapter explains basic copying functions.
NORMAL COPYING
Using the document glass
Note
1
• The document glass can scan up to 8-1/2" x 14" original.
• When a copy is made, the edges will not be copied (image loss). For
the image loss, see the "SPECIFICATIONS" (p.91).
Open the RSPF, and place the original face down on the
document glass.
[How to place the original]
Original scale
Align the original with the original scale and the
centering ( ) mark.
mark
2
Gently close the RSPF.
By factory default, when a copy is made with
the RSPF cover open, the function for
preventing excessive toner use activates and
"CHECK ORIGINAL" appears in the display.
(See the "Check RSPF open function"
(p.25).)
3
Select the number of copies and any other copy settings, and
then press the [START] key (
).
Note
• To stop copying in the middle of a run, press the [CLEAR] key (
• For the copy settings, see pages 27 through 39.
Copying books or originals with folds or creases
Press down on the RSPF while copying as shown. If
the RSPF is not completely closed, shadows may
appear on the copy or it may be fuzzy. Straighten
originals that have folds or creases before placing it
on the document glass.
24
).
!003-making copies.fm 25 ページ
2008年5月23日 金曜日 午後4時3分
MAKING COPIES
Check RSPF open function
When enabled in program number 24 (p.65), this function may help prevent wasteful use of
toner that occurs when the RSPF cover is not completely closed.
If the start (
) key is pressed when the RSPF cover is not completely closed, "CHECK
ORIGINAL" will appear in the display and copying may not take place. If copying does not
take place, copying can be performed by pressing the start (
) key again, however, the
scan size set in "CHANGING A TRAY'S PAPER SIZE SETTING" (p.23) or "VALID COPY
WIDTH" (program number 25) (p.65) will be used.
If the RSPF cover is completely closed after "CHECK ORIGINAL" appears, copying will take
place at the normal size.
Note
When this function is off, if the [Start] key (
) is pressed to make a copy
with the RSPF cover open, parts outside of the original will be copied black.
Even when this function is on, if the [Start] key (
) is pressed twice to
make a copy with the RSPF cover open, parts outside the original may be
copied black. To prevent excessive use of toner, make sure that the RSPF
cover is closed when making a copy.
3
Using the RSPF
Note
• Originals that are 5-1/2" x 8-1/2" to 8-1/2" x 14" and 15 lbs. to 24 lbs. (56 g/
m2 to 90 g/m2) can be used. A maximum of 50 pages can be placed at once.
• Straighten curled originals before placing them in the document feeder
tray. Curled originals may cause misfeeds.
• Place originals horizontally.
• Before placing originals in the document feeder tray, be sure to remove
any staples or paper clips from them.
• When a copy is made, the edges will not be copied (image loss).
For the image loss, see the "SPECIFICATIONS" (p.91).
• When using the margin shift function, check the position of the margins
carefully. (p.38)
1
Make sure that an original has not been left on the document
glass.
2
Adjust the original guides to the size of
the originals.
3
Place the original(s) face up in the
document feeder tray without trying to
force them in.
Original face up
The RSPF indicator on the operation panel will light
up. If this indicator does not light up, the originals are
not properly set or the RSPF is not properly closed.
4
Select the number of copies and any other copy settings, and then
press the [START] key (
).
Note
• The default output mode for copying from the RSPF is sort mode (P.33),
and a checkmark " " will automatically appear in the display (P.11). If
"SORT AUTO SELECT" is disabled in the user programs, the default
output mode will be non-sort mode. (P.65)
• To stop copying in the middle of a run, press the [CLEAR] key (
).
• For the copy settings, see pages 27 through 39.
25
!AL-2050CS.book
26 ページ
2008年1月7日 月曜日 午後8時10分
MAKING COPIES
Originals that cannot be used in the RSPF
The following originals cannot be used. These may cause misfeeds or smudging and
unclear images.
• Transparencies, tracing paper, other transparent or translucent paper, and
photographs.
• Carbon paper, thermal paper.
• Originals that are creased, folded, or torn.
• Glued originals, cut-out originals.
• Originals with binder holes.
• Originals printed using an ink ribbon (thermal transfer printing), originals on
thermal transfer paper.
Original output tray extension
When placing an original larger than 8-1/2" x 11" size, pull out the original output tray
extension of the RSPF.
Capacity of paper output tray
The paper output tray can hold a
maximum of 200 pages. If more
than 200 pages are allowed to
accumulate, a paper jam may occur.
Paper output tray extension
When copying onto paper larger than 8-1/2" x 11" size, pull out the paper output tray
extension.
Paper holder arm
The paper output tray has a paper holder arm. The paper holder arm presses gently
on the output paper to stack it (p.9).
Note
26
After removing paper, if you need to return the paper to the paper
output tray, lift up the paper holder arm and place the paper under
the arm.
!AL-2050CS.book
27 ページ
2008年1月7日 月曜日 午後8時10分
MAKING COPIES
Setting the number of copies
Press the numeric keys to set the number of copies.
OPY.
x11
55
The set number of copies appears in the display. A maximum of 99 copies can be set.
If you wish to make only a single copy, copying is possible with the display
showing "0".
Note
If you enter the wrong number, press the [CLEAR] key (
enter the correct number.
) and
3
SELECTING THE TRAY
Press the [TRAY SELECT] key (
).
Each time, you press the [TRAY SELECT] key (
),
the location indicated by the tray location indicator
changes in the following order : paper tray→lower
paper tray→bypass tray.
Note
READY TO COPY.
100%
EXTRA
The tray location indicator will blink when there is no paper in the paper
tray during operations, or when the tray is not closed or is improperly
closed.
27
!AL-2050CS.book
28 ページ
2008年1月7日 月曜日 午後8時10分
MAKING A COPY DARKER OR LIGHTER
Automatic exposure adjustment is initially enabled. This function automatically
adjusts the copy image according to the original being copied. If you wish to select
the exposure level yourself, follow the steps below. (Select from 2 original types and
5 exposure levels for each original type.) The exposure level used in automatic
exposure adjustment can also be changed with "AE LEVEL ADJUST" in the user
programs (p.65).
Original types
● AUTO ...... Automatic exposure adjustment is enabled and the exposure is
automatically adjusted according to the original being copied. The
exposure is lowered for colored areas and background shadows.
● TEXT ....... The exposure is raised for light areas and lowered for dark
backgrounds to make text easier to read.
● PHOTO ... Halftones in the photo are reproduced with greater clarity.
1
Place the original(s).
2
Press the [EXPOSURE] key to select the
original type.
TEXT
| | | | |
The original image type changes as follows each
time the [EXPOSURE] key is pressed: "AUTO" →
"TEXT" → "PHOTO".
Note
3
To return to auto exposure adjustment, press the [EXPOSURE] key
until "AUTO" appears.
If needed, adjust the exposure level for
TEXT or PHOTO.
For a darker image, press the [
] key (
lighter image, press the [
] key (
).
TEXT
| | | | |
). For a
4
Press the [ENTER] key.
5
Select the number of copies and any other copy settings, and
then press the [START] key (
).
Note
Exposure value guidelines (When in "TEXT" setting)
TEXT
| | | | |
Colored text or text written in pencil
Normal originals
Dark originals like newspapers
28
!AL-2050CS.book
29 ページ
2008年1月7日 月曜日 午後8時10分
REDUCTION/ENLARGEMENT/ZOOM
Copies can be reduced down to 25% or enlarged up to 400%. (When the RSPF is
being used, the zoom copy ratio range is 50% to 200%.) The [COPY RATIO] key can
be pressed to quickly select a ratio from among eight preset ratios. In addition, the
[
] key (
) and [
] key (
) can be pressed to select the ratio in increments of
1%.
1
Place the original(s) and check the paper size.
2
Press the [COPY RATIO] key.
3
Press the [COPY RATIO] key and/or [ ] key ( ) or [ ] key
( ) to select the desired copy ratio and then press the
[ENTER] key.
Selecting a preset ratio
The preset ratios change as follows each time the
[COPY RATIO] key is pressed:
"100%" → "78%" → "64%" → "50%" → "25%" →
"400%" → "200%" → "129%"
Fine adjustment of the ratio
The ratio can be adjusted from 25% to 400% in
increments of 1%.
Use the [
] key (
) or the [
] key (
) for
fine adjustment.
Note
4
COPY RATIO
- 100%
+
3
8.5x14 TO 8.5x11
78% +
ZOOM
-
99%
+
• To return the ratio to 100%, press the [COPY RATIO] key until 100%
appears.
• Press the [COPY RATIO] key to set the approximate ratio, then press
the [
] key (
) or [
] key (
).
• To decrease or increase the zoom ratio rapidly, hold down the [
]
key (
) or [
] key (
).
The ratio will stop changing at each of the preset ratios. To continue
changing the ratio, release the key and then hold it down again.
Select the number of copies and any other copy settings, and
then press the [START] key (
).
The copy will be delivered to the paper output tray.
29
!AL-2050CS.book
4
30 ページ
2008年1月7日 月曜日 午後8時10分
Chapter 4
CONVENIENT COPY
FUNCTIONS
AUTOMATIC TWO-SIDED COPYING
Two originals can be automatically copied onto both sides of a single sheet of paper.
When the RSPF is used, two-sided copies of two-sided originals can easily be made.
Original → Paper
Usable paper
One-sided original → Two sides
Document
glass
One-sided
original →
Two sides
Two-sided
original →
One side
RSPF
Two-sided
original →
Two sides
5-1/2" x 8-1/2", 8-1/2" x
11", 8-1/2" x 13",
8-1/2" x 14"
• The bypass tray
cannot be used.
5-1/2" x 8-1/2", 8-1/2" x
11", 8-1/2" x 13",
8-1/2" x 14"
• Special paper cannot
be used.
• The bypass tray can
only be used when
making one-sided
copies from twosided originals.
When performing automatic two-sided copying of one-sided originals, the orientation
of the copied image can be selected according to the binding position of the paper.
SHORT EDGE: Select when binding the paper at the short edge.
A B
(Paper orientation: Landscape)
A
B
(Paper orientation: Portrait)
LONG EDGE: Select when binding the paper at the long edge.
A
B
(Paper orientation: Landscape)
30
A B
(Paper orientation: Portrait)
!AL-2050CS.book
31 ページ
2008年1月7日 月曜日 午後8時10分
CONVENIENT COPY FUNCTIONS
Using the document glass
1
Place the original that you wish to copy onto the front side of
the paper on the document glass and close the RSPF.
2
Press the [2-SIDED COPY] key until "1 TO
2" appears, and then press the [ENTER]
key.
3
Press the [ ] key ( ) or [ ] key ( ) to
select the binding edge and then press the
[ENTER] key.
2-SIDED COPY
1 TO 2
BINDING EDGE
LONG EDGE
Select "LONG EDGE" or "SHORT EDGE".
The "LONG EDGE" and "SHORT EDGE" are
shown in the illustration on the preceding page.
4
4
Select the number of copies and any other settings, and then
press the [START] key (
).
"[START] : NEXT SCAN [#] : START PRINT" appears and the original is
scanned into memory.
To immediately print the scanned image, press the [
] key.
Replace the original with the next
original and close the RSPF, and
then press the [START] key (
).
Note
2
Repeat step 5 until all originals have been
scanned.
Copies will be output each time two originals
have been scanned.
When the number of original pages is odd
The first original The second original
and "[START] : NEXT SCAN [#] : START
PRINT" appears, press the [
] key after all pages have been scanned.
1
5
• If you need to clear the data scanned into memory, press the
[CLEAR] key (
). When the [CLEAR] key (
) is pressed, the
number of copies setting is also cleared.
• To cancel automatic two-sided copying, press the [CLEAR ALL] key
(
) or press the [2-SIDED COPY] key, select the "1 TO 1", and then
press the [ENTER] key.
• If the special function sort mode was selected in step 4, copying will
not begin until the [
] key is pressed.
31
!AL-2050CS.book
32 ページ
2008年1月7日 月曜日 午後8時10分
CONVENIENT COPY FUNCTIONS
Using the RSPF
1
Place the original(s) in the RSPF. (p.25)
If you place an odd number of originals for one-sided to two-sided copying,
the last page will be one-sided.
2
Press the [2-SIDED COPY] key and select
the two-sided copy mode that you wish to
use.
2-SIDED COPY
2 TO 1
The mode changes as follows each time you press
the [2-SIDED COPY] key:
"1 TO 1" → "1 TO 2" → "2 TO 2" → "2 TO 1"
• "1 TO 2": Two-sided copies from one-sided originals
• "2 TO 2": Two-sided copies from two-sided originals
• "2 TO 1": One-sided copies from two-sided originals
3
Press the [ENTER] key.
If you selected "1 TO 2" in step 2, select "LONG EDGE" or "SHORT EDGE"
and press the [ENTER] key. LONG EDGE and SHORT EDGE are shown in
the illustration on page 30.
4
If you selected "2 TO 1" or "2 TO 2", press
the [ ] key ( ) or [ ] key ( ) to select
the original size and then press the
[ENTER] key.
ORIG. SIZE ENTER
5.5x8.5
The following original sizes can be selected:
"8.5x14", "8.5x13", "8.5x11", "5.5x8.5", "A4", "B5",
"A5"
5
Select the number of copies and any other settings, and then
press the [START] key (
).
The copy will be delivered to the paper output tray.
Note
32
To cancel automatic two-sided copying, press the [CLEAR ALL] key
(
) or press the [2-SIDED COPY] key, select the "1 TO 1", and then
press the [ENTER] key.
!AL-2050CS.book
33 ページ
2008年1月7日 月曜日 午後8時10分
SORT COPY
Copies of multiple original pages can be sorted into sets.
Note
The number of pages that can be scanned varies depending on the
original type (photo, text, etc.) and the amount of memory allocated to
the printer. The amount of memory allocated to the printer can be
changed with "MEM. FOR PRINTER" in the user programs. (p.64)
1 2 3
2
3
1 2 3
1
1 2 3
Sort copy
Using the document glass
1
Place the first original. (p.24)
2
Press the [E-SORT/SP.FUN] key until
"SORT" appears and then press the
[ENTER] key.
3
Press the [ ] key ( ) to move " " to
the "ON" position and then press the
[ENTER] key.
4
Select the number of copies and any other settings, and then
press the [START] key (
).
SPECIAL FUNCTION
SORT
SORT
ON
4
OFF
"[START] : NEXT SCAN [#] : START PRINT" appears and the original is
scanned into memory.
5
Replace the original with the next original, and then press the
[START] key ( ).
Repeat step 5 until all originals have been scanned into memory.
Note
6
To clear the data in memory, press the [CLEAR] key (
). When the
[CLEAR] key (
) is pressed, the number of copies setting is also cleared.
When all originals have been scanned, press the [
] key.
The copies are delivered to the paper output tray.
Note
• To cancel the sort copy job, press the [CLEAR] key (
).
• To cancel sort copy mode, press the [CLEAR ALL] key (
).
33
!AL-2050CS.book
34 ページ
2008年1月7日 月曜日 午後8時10分
CONVENIENT COPY FUNCTIONS
Using the RSPF
1
Place the originals. (p.25)
• If "SORT AUTO SELECT" is enabled in the user programs, the default output
mode for copying from the RSPF is sort mode (p.65). In this case go directly
to step 4. A checkmark " " will automatically appear in the display (p.11).
• If "SORT AUTO SELECT" is disabled, the default output mode will be nonsort mode. Follow the steps below to select sort mode.
Note
2
Press the [E-SORT/SP.FUN] key until
"SORT" appears and then press the
[ENTER] key.
3
Press the [ ] key ( ) to move " " to
the "ON" position and then the [ENTER]
key.
4
Select the number of copies and any other settings, and then
press the [START] key (
).
SPECIAL FUNCTION
SORT
SORT
ON
OFF
The copies are delivered to the paper output tray.
• To cancel the sort copy job, press the [CLEAR] key (
).
• To cancel sort copy mode, press the [CLEAR ALL] key (
).
Note
If the memory becomes full
• If the memory becomes full while scanning the originals, "MEMORY FULL, PRESS
START TO RESUME" will appear in the display, and the machine will stop copying.
• To copy the originals that have been scanned up to that point, press the [START]
key ( ).
• To clear the data that has been scanned into memory, press the [CLEAR ALL] key
( ) or the [CLEAR] key ( ).
Offset function during sort copy
The offset function shifts the position of each set of copies in the paper output tray
for easy separation.
The offset function can be changed with "OFFSET FUNCTION" in the user
programs. (p.63)
1
2
3
1 1
Offset function
34
1
2
3
1
When offset function is disabled
!AL-2050CS.book
35 ページ
2008年1月7日 月曜日 午後8時10分
COPYING MULTIPLE ORIGINALS ONTO A SINGLE
SHEET OF PAPER
(2 IN 1 copy)
Multiple originals can be copied onto a single sheet of paper in a selected layout
pattern.
This function is convenient for compiling multi-page reference materials into a
compact format, or for providing an overview of all pages of a document on a single
page.
Pattern 1
Note
Pattern 2
• An appropriate ratio setting will be automatically selected based on
the size of the originals, the size of the paper. When using the
document glass, reduction is possible to 25%. When using the RSPF,
reduction is possible to 50%. Certain combinations of original size
and paper size may result in images being cut off.
• 2 IN 1 copying cannot be used in combination with the margin shift
copying.
• The 2 IN 1 layout pattern can be changed with "LAYOUT IN 2IN1" in
the user programs (p.63).
• The bypass tray cannot be used for 2 IN 1 copying.
4
Using the document glass
1
Place the first original. (p.24)
2
Press the [E-SORT/SP.FUN] key until
"2IN1" appears and then press the
[ENTER] key.
3
Press the [ ] key ( ) to move " " to
the "ON" position and then press the
[ENTER] key.
SPECIAL FUNCTION
2IN1
2IN1
ON
OFF
35
!AL-2050CS.book
36 ページ
2008年1月7日 月曜日 午後8時10分
CONVENIENT COPY FUNCTIONS
4
Press the [ ] key ( ) or [ ] key ( ) to
select the original size and then press the
[ENTER] key.
ORIG. SIZE ENTER
5.5x8.5
The following original sizes can be selected:
"8.5x14", "8.5x13", "8.5x11", "5.5x8.5", "A4", "B5",
"A5"
5
Select the number of copies and any other settings, and then
press the [START] key (
).
"[START] : NEXT SCAN [#] : START PRINT" appears and the original is
scanned into memory.
To immediately print the scanned image, press the [
] key.
6
Replace the original with the next original, and then press the
[START] key ( ).
Repeat step 6 until all originals have been scanned.
Copies will be output each time two originals have been scanned.
When the number of original pages is odd and "[START] : NEXT SCAN [#] :
START PRINT" appears, press the [
] key after all pages have been
scanned.
Note
36
• To clear the data in memory, press the [CLEAR] key (
).
When the [CLEAR] key (
) is pressed, the number of copies
setting is also cleared.
• To cancel 2 IN 1 copying, press the [CLEAR] key (
).
• To cancel 2 IN 1 copy mode, press the [CLEAR ALL] key (
).
!AL-2050CS.book
37 ページ
2008年1月7日 月曜日 午後8時10分
CONVENIENT COPY FUNCTIONS
Using the RSPF
1
Place the originals. (p.25)
2
Press the [E-SORT/SP.FUN] key until
"2IN1" appears and then press the
[ENTER] key.
3
Press the [ ] key ( ) to move " " to
the "ON" position and then press the
[ENTER] key.
4
Press the [ ] key ( ) or [ ] key ( ) to
select the original size and then press the
[ENTER] key.
SPECIAL FUNCTION
2IN1
2IN1
ON
OFF
ORIG. SIZE ENTER
5.5x8.5
4
The following original sizes can be selected:
"8.5x14", "8.5x13", "8.5x11", "5.5x8.5", "A4", "B5",
"A5"
5
Select the number of copies and any other settings, and press
the [START] key (
).
The copy is delivered to the paper output tray.
Note
• To cancel 2 IN 1 copying, press the [CLEAR] key (
).
• To cancel 2 IN 1 copy mode, press the [CLEAR ALL] key (
).
37
!AL-2050CS.book
38 ページ
2008年1月7日 月曜日 午後8時10分
CREATING MARGINS WHEN COPYING
(Margin shift)
The margin shift function is used to automatically shift the text or image or the copy
paper approximately 1/2".
As shown below, LONG EDGE or SHORT EDGE can be selected.
AB
SHORT EDGE
RSPF
BA
LONG EDGE
AB
AB
Margin
Margin
Copy
Document glass
Original
Note
38
• This feature cannot be used with the 2 IN 1 feature.
• The margin width can be changed with "MARGIN WIDTH" in the user
programs. (p.64)
• Note that a margin is created by shifting the image, and thus if the
image is shifted too far, the edge of the image may be cut off.
1
Place the original(s).
2
Press the [E-SORT/SP.FUN] key until
"MARGIN SHIFT" appears and then press
the [ENTER] key.
SPECIAL FUNCTION
MARGIN SHIFT
!AL-2050CS.book
39 ページ
2008年1月7日 月曜日 午後8時10分
CONVENIENT COPY FUNCTIONS
3
Press the [ ] key ( ) to move " " to
the "ON" position and then press the
[ENTER] key.
4
Press the [ ] key ( ) or [ ] key ( ) to
select the margin position and then press
the [ENTER] key.
MARGIN SHIFT
ON
OFF
MARGIN SHIFT
LONG EDGE
Select "LONG EDGE" or "SHORT EDGE".
For the margin position, see the previous page.
5
Select the number of copies and any other settings, and then
press the [START] key (
).
The copy is delivered to the paper output tray.
Note
• To cancel margin shift copying, press the [CLEAR] key (
).
• To cancel margin shift mode, press the [CLEAR ALL] key (
).
4
39
!AL-2050CS.book
5
40 ページ
2008年1月7日 月曜日 午後8時10分
Chapter 5
INSTALLING THE SOFTWARE
This chapter explains how to install and configure the software that is required for the
printer and scanner functions of the machine. The procedure for viewing the Online
Manual is also explained.
Note
• The explanations of screens and procedures in this manual are
primarily for Windows XP.
• This manual refers to the CD-ROM that accompanied the machine
simply as "CD-ROM".
SOFTWARE
The CD-ROM that accompanies the machine contains the following software:
MFP driver
Printer driver
The printer driver enables you to use the printer function of the machine.
The printer driver includes the Print Status Window. This is a utility that monitors
the machine and informs you of the printing status, the name of the document
currently being printed, and error messages.
Please note that the Print Status Window does not operate when the machine is
used as a network printer.
Scanner driver*
The scanner driver allows you to use the scanning function of the machine with
TWAIN-compliant and WIA-compliant applications.
Sharpdesk*
Sharpdesk is an integrated software environment that makes it easy to manage
documents and image files, and launch applications.
Button Manager*
Button Manager allows you to use the scanner menus on the machine to scan a
document.
* The scanning feature can only be used with computers that are connected to the
machine by a USB cable. If you are connected to the machine by a LAN connection,
only the printer function can be used.
40
!AL-2050CS.book
41 ページ
2008年1月7日 月曜日 午後8時10分
BEFORE INSTALLATION
Hardware and software requirements
Check the following hardware and software requirements in order to install the
software.
Computer type
IBM PC/AT or compatible computer equipped with a
USB2.0*1/1.1*2 or 10Base-T LAN interface
5
Operating system*3 *4 Windows 98, Windows Me, Windows 2000 Professional* ,
Windows XP*5, Windows Vista*5
Display
1024 x 768 dots resolution and 16-bit color or higher is
recommended.
Hard disk free space 150 MB or more
Other hardware
requirements
An environment on which any of the operating systems
listed above can fully operate
*1 The machine's USB connector will transfer data at the speed specified by the USB 2.0
(Hi-Speed) only if the Microsoft USB 2.0 driver is installed in the computer.
*2 Compatible with Windows 98, Windows Me, Windows 2000 Professional, Windows XP
or Windows Vista preinstalled model standardly equipped with a USB port.
*3 Printing is not available in MS-DOS mode.
*4 The machine does not support printing from a Macintosh environment.
*5 Administrator's rights are required to install the software using the installer.
5
Installation environment and usable software
The following table shows the drivers and software that can be installed for each
version of Windows and interface connection method.
Cable
USB
LAN
Operating system
Windows 98/Me/
2000/XP/Vista
Windows 98/Me/
2000/XP/Vista
Printer
driver
Scanner
driver
Button
Manager
Sharpdesk
Available
Available*
Not Available
* The printer driver that is installed will vary depending on the type of connection
between the machine and your computer.
41
!AL-2050CS.book
42 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE SOFTWARE
Note
• If you need to use a different connection method after installing the
software using a USB or network connection, you must first uninstall
the software and then install it using the new connection method.
• The screen images in this manual are mainly for Windows XP. With
other versions of Windows, some screen images may be different
from those in this manual.
• In the following explanations it is assumed that the mouse is
configured for right hand operation.
• The scanner function only works when using a USB cable.
• If an error message appears, follow the instructions on the screen to
solve the problem. After the problem is solved, the installation
procedure will continue. Depending on the problem, you may have to
click the "Cancel" button to exit the installer. In this case, reinstall the
software from the beginning after solving the problem.
Using the machine with a USB connection
1
The USB cable must not be connected to the machine. Make
sure that the cable is not connected before proceeding.
If the cable is connected, a Plug and Play window will appear. If this
happens, click the "Cancel" button to close the window and disconnect the
cable.
Note
The cable will be connected in step 13.
2
Insert the CD-ROM into your computer's CD-ROM drive.
3
Click the "start" button, click "My Computer" (
double-click the CD-ROM icon ( ).
), and then
• In Windows Vista, click the "Start" button, click "Computer", and then
double-click the CD-ROM icon.
• In Windows 98/Me/2000, double-click "My Computer", and then
double-click the CD-ROM icon.
4
Double-click the "setup" icon (
).
In Windows Vista, if a message screen appears asking you for confirmation,
click "Allow".
5
The "SOFTWARE LICENSE" window will appear. Make sure
that you understand the contents of the software license, and
then click the "Yes" button.
Note
42
You can show the "SOFTWARE LICENSE" in a different language by
selecting the desired language from the language menu. To install the
software in the selected language, continue the installation with that
language selected.
!AL-2050CS.book
43 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE SOFTWARE
6
Read the "Readme First" in the "Welcome" window and then
click the "Next" button.
7
To install all of the software, click
the "Standard" button and go to
step 12.
To install particular packages,
click the "Custom" button and go
to next step.
8
Click the "MFP Driver" button.
Click the "Display Readme" button to
show information on packages that are
selected.
5
9
The files required for installation of the MFP driver are copied.
Follow the on-screen instructions.
When "The installation of the SHARP software is complete." appears, click
the "OK" button.
Caution
• If you are using Windows Vista and a security warning window
appears, be sure to click "Install this driver software anyway".
• If you are running Windows 2000/XP and a warning message
appears regarding the Windows logo test or digital signature, be sure
to click "Continue Anyway" or "Yes".
43
!AL-2050CS.book
44 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE SOFTWARE
10
You will return to the window of step 8. If you wish to install
Button Manager or Sharpdesk, click the "Utility Software"
button.
If you do not wish to install the Utility Software, click the "Close" button and
go to step 12.
Note
After the installation, a message prompting you to restart your computer
may appear. In this case, click the "Yes" button to restart your computer.
Installing the Utility Software
11
Click the "Button Manager" or the
"Sharpdesk" button.
Click the "Display Readme" button to
show information on packages that are
selected.
Follow the on-screen instructions.
In Windows 98/Me/2000, if the following screen appears, click the "Skip"
Caution button or the "Continue" button as appropriate to continue the
Sharpdesk installation.
If "Skip" is selected, the Sharpdesk
installation will continue without
installing Sharpdesk Imaging.
If "Continue" is selected,
Sharpdesk Imaging will be
installed. If Imaging for Windows is
installed on your computer,
Sharpdesk Imaging will overwrite
Imaging for Windows.
44
!AL-2050CS.book
45 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE SOFTWARE
12
When installing is finished, click the "Close" button.
Caution
• If you are using Windows Vista and a security warning window
appears, be sure to click "Install this driver software anyway".
• If you are running Windows 2000/XP and a warning message
appears regarding the Windows logo test or digital signature, be sure
to click "Continue Anyway" or "Yes".
A message will appear instructing you to connect the machine to your
computer. Click the "OK" button.
Note
13
After the installation, a message prompting you to restart your computer
may appear. In this case, click the "Yes" button to restart your computer.
Make sure that the power of the machine is turned on, and then
connect the USB cable (p.46).
Windows will detect the machine and a Plug and Play screen will appear.
14
Follow the instructions in the plug and play window to install
the driver.
Follow the on-screen instructions.
Caution
• If you are using Windows Vista and a security warning window
appears, be sure to click "Install this driver software anyway".
• If you are running Windows 2000/XP and a warning message
appears regarding the Windows logo test or digital signature, be sure
to click "Continue Anyway" or "Yes".
5
This completes the installation of the software.
• If you installed Button Manager, set up Button Manager as explained in "SETTING
UP BUTTON MANAGER" (p.53).
• If you installed Sharpdesk, the Sharpdesk setup screen will appear. Follow the
instructions in the screen to set up Sharpdesk.
45
!AL-2050CS.book
46 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE SOFTWARE
Connecting a USB cable
Follow the procedure below to connect the machine to your computer.
A USB cable for connecting the machine to your computer is not included with the
machine. Please purchase the appropriate cable for your computer.
Caution
Note
46
• USB is available with a PC/AT compatible computer that was
originally equipped with USB and had Windows 98, Windows Me,
Windows 2000 Professional, Windows XP or Windows Vista
preinstalled.
• Do not connect the USB cable before installing the printer driver. The
USB cable should be connected during installation of the printer
driver.
• If the machine will be connected using a USB 2.0 port of your
computer, please purchase a USB cable that supports USB 2.0.
• To obtain the fastest USB 2.0 data transfer speed, "USB2.0 MODE
SWITCH" in the machine's user programs must be set to
"HI-SPEED". For more information, see "USER PROGRAMS" (p.66).
• Use the machine's "HI-SPEED" mode only when using a computer
that is running Windows 2000/XP/Vista.
• Even when the Microsoft USB 2.0 driver is used, it may not be
possible to obtain full USB 2.0 speed if a PC card supporting USB 2.0
is used. To obtain the latest driver (which may enable a higher
speed), contact the manufacturer of your PC card.
• Connection is also possible using a USB 1.1 port on your computer.
However, the specifications will be USB 1.1 specifications
(Full-Speed).
1
Insert the cable into the USB
connector on the machine.
2
Insert the other end of the cable into your computer's USB port.
!AL-2050CS.book
47 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE SOFTWARE
Using the machine as a network printer
Note
1
• Interface cables for connecting the machine to your computer are not
included with the machine. Please purchase the appropriate cable for
your computer.
• If you intend to use the machine as a scanner, it must be connected
to your computer with a USB interface cable. The scanner function
cannot be used if the machine is connected with a LAN cable.
Insert the LAN cable into the LAN
connector on the machine.
Use a network cable that is shielded.
2
Turn on the machine.
3
Insert the CD-ROM into your computer's CD-ROM drive.
4
Click the "start" button, click "My Computer" (
double-click the CD-ROM icon ( ).
), and then
• In Windows Vista, click the "Start" button, click "Computer", and then
double-click the CD-ROM icon.
• In Windows 98/Me/2000, double-click "My Computer", and then
double-click the CD-ROM icon.
5
Double-click the "setup" icon (
5
).
In Windows Vista, if a message screen appears asking you for confirmation,
click "Allow".
6
The "SOFTWARE LICENSE" window will appear. Make sure
that you understand the contents of the software license, and
then click the "Yes" button.
Note
7
You can show the "SOFTWARE LICENSE" in a different language by
selecting the desired language from the language menu. To install the
software in the selected language, continue the installation with that
language selected.
Read the "Readme First" in the "Welcome" window and then
click the "Next" button.
Note
To set the IP address of the machine, follow the steps below. If the
machine is already connected to the network and its IP address has
been set, go to "LPR (TCP/IP) direct printing" (p.49).
47
!AL-2050CS.book
48 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE SOFTWARE
Set the IP Address
This setting is only required once when using the machine on a network.
8
Click the "Set the IP Address"
button.
9
The printer or printers connected
to the network will be detected.
Click the printer to be configured
(the machine) and click the "Next"
button.
Note
10
• The "Ethernet Address" is indicated on the left side of the machine
near the LAN connector.
• If the machine can not be recognized, enter the Ethernet Address
and click the "Initialize" button to initialize the IP address. Follow the
on-screen instructions to click the "OK" button and then the "Search"
button. If the machine is still not recognized, disable your computer's
firewall and then repeat the installation from the beginning.
Enter the IP address, subnet
mask, and default gateway.
The settings in the above window are
examples.
Be sure to ask your network
administrator for the correct IP address,
subnet mask, and default gateway to be
entered.
Note
48
When "Get IP Address Automatically" is selected, the IP address may at
times change automatically. This will prevent printing. In this event,
select "Assign IP Address" and enter the IP address.
!AL-2050CS.book
49 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE SOFTWARE
11
Click the "Next" button.
12
Click the "Yes" button in the confirmation dialog box that
appears.
Go to step 11.
LPR (TCP/IP) direct printing
After step 1-7 on page 47
8
Click the "Printer Driver" button.
9
Read the message in the "Welcome" window and then click the
"Next" button.
If you have not set the IP Address, click
the "Set the IP Address" button first and
go to step 8 on page 48.
10
Select "LPR Direct Print" and
click the "Next" button.
11
The printer or printers connected
to the network will be detected.
Click the printer to be configured
(the machine) and click the "Next"
button.
Note
5
If the machine's IP address cannot be found, make sure the machine is
powered on, make sure the network cable is connected correctly, and
then click the "Search" button.
49
!AL-2050CS.book
50 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE SOFTWARE
12
In the window for setting the
destination print port name, make
sure that ":lp" appears at the end
of the IP address and click the
"Next" button.
Note
13
Any name can be entered in "Printer Port Name" (maximum of 38
characters).
A window appears to let you
check your entries. Make sure
that the entries are correct and
then click the "Finish" button.
If any of the entries are incorrect, click
the "Back" button to return to the
appropriate window and correct the
entry.
14
Select the port you want to use with the machine, and click the
"Next" button.
15
Select whether or not you wish the printer to be your default
printer and click the "Next" button.
Follow the on-screen instructions.
Caution
• If you are using Windows Vista and a security warning window
appears, be sure to click "Install this driver software anyway".
• If you are running Windows 2000/XP and a warning message
appears regarding the Windows logo test or digital signature, be sure
to click "Continue Anyway" or "Yes".
16
When "The installation of the SHARP software is complete."
appears, click the "OK" button.
17
When the "Finish" screen appears, click the "Close" button.
Note
After the installation, a message prompting you to restart your computer
may appear. In this case, click the "Yes" button to restart your computer.
This completes the installation of the software.
50
!AL-2050CS.book
51 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE SOFTWARE
Sharing the printer using windows networking
If the machine will be used as a shared printer on a network, follow these steps to
install the printer driver in the client computer.
Note
To configure the appropriate settings in the print server, see the
operation manual or help file of your operating system.
1
Perform steps 3 through 7 in "Using the machine as a network
printer" (p.47).
2
Click the "Printer Driver" button.
3
Select "Shared Printer" and click
the "Next" button.
4
For the port to be used, select the
machine set as a shared printer,
and click the "Next" button.
5
If you are using Windows 98/Me/2000/XP,
you can also click the "Add Network Port"
button and select the printer to be shared
by browsing the network in the window
that appears. (In Windows Vista, the "Add
Network Port" button does not appear.)
Note
If the shared printer does not appear in the list, check the settings in the
printer server.
51
!AL-2050CS.book
52 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE SOFTWARE
5
Follow the on-screen instructions.
6
When the "Finish" screen appears, click the "Close" button.
Note
After the installation, a message prompting you to restart your computer
may appear. In this case, click the "Yes" button to restart your computer.
This completes the installation of the software.
52
!AL-2050CS.book
53 ページ
2008年1月7日 月曜日 午後8時10分
SETTING UP BUTTON MANAGER
Button Manager is a software program that works with the scanner driver to enable
scanning from the machine.
To scan using the machine, Button Manager must be linked with the scan menu on
the machine. Follow the steps below to link Button Manager to scanner events.
Windows XP/Vista
1
Click the "start" button, click "Control Panel", click "Printers
and Other Hardware", and then click "Scanners and Cameras".
In Windows Vista, click the "Start" button, select "Control Panel" and click
"Hardware and Sound", and then click "Scanners and Cameras".
2
Click the "SHARP AL-XXXX" icon and select "Properties" from
the "File" menu.
In Windows Vista, select "Properties" from the "Organize" menu.
3
In the "Properties" screen, click the "Events" tab.
4
Select "SC1:" from the "Select an
event" pull-down menu.
5
53
!AL-2050CS.book
54 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE SOFTWARE
5
Select "Start this program" and
then select "Sharp Button
Manager O" from the pull-down
menu.
6
Click the "Apply" button.
7
Repeat Steps 4 through 6 to link Button Manager to "SC2:"
through "SC6:".
Select "SC2:" from the "Select an event" pull-down menu. Select "Start this
program", select "Sharp Button Manager O" from the pull-down menu, and
then click the "Apply" button. Do the same for each ScanMenu through
"SC6:".
When the settings have been completed, click the "OK" button to close the
screen.
Button Manager is now linked to the scan menu (1 through 6).
The scan settings for each of scan menu 1 through 6 can be changed with
the setting window of Button Manager.
For the factory default settings of the scan menu and the procedures for
configuring Button Manager settings, see "Button Manager Settings" in the
Online Manual.
54
!AL-2050CS.book
55 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE SOFTWARE
Windows 98/Me/2000
1
Click the "Start" button, select "Settings", and then click
"Control Panel".
2
Double-click the "Scanners and Cameras" icon.
Note
3
If the "Scanners and Cameras" icon does not appear in Windows Me,
click "view all Control Panel options".
Select "SHARP AL-XXXX" and click the "Properties" button.
In Windows Me, right click "SHARP AL-XXXX" and click "Properties" in the
pop-up menu.
4
In the "Properties" screen, click the "Events" tab.
5
Select "SC1:" from the "Scanner
events" pull-down menu.
5
55
!AL-2050CS.book
56 ページ
2008年1月7日 月曜日 午後8時10分
INSTALLING THE SOFTWARE
6
Select "Sharp Button Manager O"
in "Send to this application".
Note
If other applications are shown, deselect the checkboxes for the other
applications and leave only the Button Manager checkbox selected.
7
Click the "Apply" button.
8
Repeat Steps 5 through 7 to link Button Manager to "SC2:"
through "SC6:".
Select "SC2:" from the "Scanner events" pull-down menu. Select "Sharp
Button Manager O" in "Send to this application" and click the "Apply" button.
Do the same for each ScanMenu through "SC6:".
When the settings have been completed, click the "OK" button to close the
screen.
Button Manager is now linked to the scan menu (1 through 6).
The scan settings for each of scan menus 1 through 6 can be changed with
the setting window of Button Manager.
For the factory default settings of the scan menu and the procedures for
configuring Button Manager settings, see "Button Manager Settings" in the
Online Manual.
56
!AL-2050CS.book
6
57 ページ
2008年1月7日 月曜日 午後8時10分
Chapter 6
PRINTER/SCANNER
FUNCTIONS
The machine includes a USB connector and a LAN connector as standard
equipment.
When the USB connector is used, the printer and scanner functions can be used.
When the LAN connector is used, the printer function can be used.
The machine has the following features:
• High-speed data transfer (when connected to a USB 2.0 connector)
• ROPM* function
* ROPM is an acronym for "Rip Once Print Many" processing. The ROPM function stores
multiple pages of print data in memory before printing. When printing multiple copies,
this eliminates the need for the computer to repeatedly transmit the print data.
To use the machine as a printer or scanner, the printer driver or scanner driver must
first be installed as explained in the "INSTALLING THE SOFTWARE".
Note
• If a problem occurs in printer or scanner mode, see the Online
Manual.
• When using USB 2.0 (Hi-Speed mode), be sure to read "System
requirements for USB 2.0 (Hi-Speed mode)" (below) to verify that
your system and the machine settings are configured appropriately.
System requirements for USB 2.0 (Hi-Speed mode)
The following system is required to use USB 2.0 (Hi-Speed mode):
• Your computer must be running Windows 2000 Professional/XP/Vista and the
Microsoft USB 2.0 driver must be installed.
• The "USB 2.0 MODE SWITCH" setting in the machine's user programs must be
set to "HI-SPEED". To change the setting, see "USB 2.0 MODE SWITCH" in the
user programs (p.66).
6
* Even when the Microsoft USB 2.0 driver is installed, some USB 2.0 expansion cards
are not capable of attaining the speed stipulated by the Hi-Speed standard. This
problem can often be fixed by installing a more recent driver for the card. To obtain
the most recent driver for your card, contact the card's manufacturer.
57
!AL-2050CS.book
58 ページ
2008年1月7日 月曜日 午後8時10分
USING THE PRINTER MODE
The procedure for loading paper for printing is the same as for loading copy paper.
See "LOADING PAPER" (p.18).
Note
• Print jobs received while the machine is copying will be stored in
memory. When the copy job is finished, the print jobs will begin
printing.
• Printing is not possible when the front or side cover is opened for
machine maintenance, or when a misfeed occurs or the machine
runs out of paper or toner, or when the drum cartridge reaches its
replacement time.
BASIC PROCEDURE FOR PRINTING
The basic procedure for printing is explained in the following. To use convenient
printer functions, see the "Online Manual" or the printer driver help file.
1
Make sure that paper is loaded in the tray.
The procedure for loading paper is the same as for copying. See "LOADING
PAPER" (p.18) and make sure that the paper you wish to use is loaded.
Note
Make sure that the paper size setting on the machine is the same as the
paper size set in the printer driver.
2
Open the file that you wish to print and select "Print" from the
File menu.
3
Make sure that the printer driver for the machine is selected,
and select print settings in the printer driver.
For information on the settings in the printer driver, see the "Online Manual"
or the printer driver help file.
4
Click the "Print" button or the "OK" button to begin printing.
The print job will be delivered to the paper output tray.
Canceling a print job
1
Select printer mode with the [MODE SELECT] key on the
operation panel of the machine, and then press the [CLEAR]
key ( ) or the [CLEAR ALL] key ( ).
2
"CANCEL PRINT JOB?" will appear in the display. Make sure
that a checkmark appears in front of "YES" and press the
[ENTER] key.
Note
58
For limitations on copying in print mode, scanner mode limitations, and
print mode limitations in copy and scanner mode, see "OPERATION IN
COPY, PRINTER, AND SCANNER MODES" (p.60).
!AL-2050CS.book
59 ページ
2008年1月7日 月曜日 午後8時10分
USING THE SCANNER MODE
The procedure for placing the original is the same as for copying. See "NORMAL
COPYING" (p.24).
Note
Scanner mode cannot be used at the following times:
• A misfeed has occurred (paper misfeed or original misfeed in the
RSPF).
• The user programs are being used.
• The tray paper size is being set.
• The machine is being used in copy mode.
• The front cover or side cover is open.
SCANNING USING THE KEYS ON THE MACHINE
When scanning is performed by this method, the application that has been set in
Button Manager will automatically start and the scanned image will be pasted into
the application.
Note
If the machine is in copy mode, press the [MODE SELECT] key to
switch to scanner mode and clear the previously set copy settings.
Scanning from the operation panel of the machine
1
Press the [MODE SELECT] key to select
scanner mode.
The "SCAN" indicator lights up to indicate that
scanner mode is selected.
6
2
Place the original. (p.24)
3
Press the [ ] key ( ) or [ ] key ( ) to
select the desired Button Manager scan
menu setting.
4
Press the [START] key (
Note
SCAN USING:
SC1:
) to begin scanning.
Scanner mode remains selected after scanning is finished. (To change
to a different mode, use the [MODE SELECT] key.)
59
!AL-2050CS.book
60 ページ
2008年1月7日 月曜日 午後8時10分
PRINTER/SCANNER FUNCTIONS
Button Manager scan menu
For information on Button Manager settings, see the Button Manager help file. The
names in the Button Manager menu ("xxxx" in "SC1:xxxx", etc.) can be changed.
See the online manual.
SCANNING FROM YOUR COMPUTER
The machine supports the TWAIN standard, making it possible to scan from TWAINcompliant applications. The machine also supports WIA (Windows Image
Acquisition), making it possible to scan from the "Scanner and Camera Wizard" in
Windows XP. See the Online Manual for the procedures for TWAIN and WIA
scanning. For information on TWAIN and WIA settings, see the help file for the
scanner driver or Windows Help.
OPERATION IN COPY, PRINTER, AND SCANNER
MODES
Some operations cannot be performed simultaneously when the machine is being
used in printer mode, copy mode, or scanner mode.
Modes
Copy
Printer
Copy key input
Copying
Yes
During copying
During printing
Scanner During scan preview/
during scanning
Printing
Scanning
from the
machine
Yes
Yes
No
No
No
No
Yes*3
Yes*3
Yes*1
No
Scanning
from a
computer
Yes*2
*1 During two-sided printing, the copy job begins after the print job finishes.
*2 Printing is possible while scanning is taking place. Printing begins after scanning
ends when connected by the LAN connector.
*3 Scanning begins after printing ends when connected by the LAN connector and
two-sided printing is taking place.
60
!AL-2050CS.book
61 ページ
2008年1月7日 月曜日 午後8時10分
HOW TO USE THE ONLINE MANUAL
The online manual provides detailed instructions for operating the unit as a printer
and scanner. It also provides methods for dealing with printing or scanner problems.
1
Turn on your computer.
2
Insert the supplied CD-ROM into your CD-ROM drive.
3
Click the "start" button, click "My Computer" (
double-click the CD-ROM ( ) icon.
), and then
• In Windows Vista, click the "Start" button, click "Computer", and then
double-click the CD-ROM icon.
• In Windows 98/Me/2000, double-click "My Computer" and then doubleclick the CD-ROM icon.
4
Double-click the "Manual" folder, double-click the "EnglishA"
folder, and then double-click the "AL_2050CS.pdf" icon.
5
Click
to read the online manual.
To close the online manual, click the (
the window.
Note
) button located at the top-right of
• The online manual can be printed out using Acrobat Reader. It is
useful to print out sections that you refer to frequently.
• Refer to Acrobat Reader "Help" for more details on the operation and
functions of Acrobat Reader.
Viewing the online manual
6
The "CD-ROM" that accompanies the machine contains an online manual in PDF
format. To view the manual in PDF format, Acrobat Reader or Adobe Reader of
Adobe Systems Incorporated is required. If neither program is installed on your
computer, the programs can be downloaded from the following URL:
http://www.adobe.com/
61
!AL-2050CS.book
7
62 ページ
2008年1月7日 月曜日 午後8時10分
Chapter 7
USER SETTINGS
The user settings allow you to customize machine settings to better meet your
needs.
USER PROGRAMS
The user settings consist of the following items.
To change a user program setting, see "SELECTING A SETTING FOR A USER
PROGRAM" (p.67).
Copy mode
Program
number
1
62
Program name
AUTO CLEAR
Setting codes
(factory default
setting appears
in bold)
Explanation
1: 10 SEC.
2: 30 SEC.
3: 60 SEC.
4: 90 SEC.
5: 120 SEC.
6: OFF
• Auto clear time automatically
returns the copy settings to
the initial settings (p.16) if no
keys are pressed for a preset
period of time following the
end of a copy job.
• This program is used to select
the period of time. Auto clear
time can also be disabled.
• This function automatically
switches the machine to a low
power consumption state if
the set duration of time
elapses without the machine
being used when the power is
on. The power save indicator
lights up, however, the keys
on the operation panel can be
used. Normal operation
automatically resumes when
a key on the operation panel
is pressed, an original is
placed, a print job is received.
• Use this setting to enable or
disable auto power shut-off
mode.
2
PREHEAT MODE
1: 30 SEC.
2: 1 MIN.
3: 5 MIN.
4: 30 MIN.
5: 60 MIN.
6: 120 MIN.
7: 240 MIN.
3
AUTO SHUT-OFF
1: ON
2: OFF
!AL-2050CS.book
63 ページ
2008年1月7日 月曜日 午後8時10分
USER SETTINGS
Program
number
4
7
8
9
10
Program name
AUTO SHUT-OFF
TIME
LAYOUT IN 2IN1
OFFSET
FUNCTION
ROTATE ORIG.
IMAGE
AE/TEXT
RESOLUTION
Setting codes
(factory default
setting appears
in bold)
Explanation
1: 5 MIN.
2: 30 MIN.
3: 60 MIN.
4: 120 MIN.
5: 240 MIN.
• This function automatically
switches the machine to a state
that consumes even less power
than preheat mode if the set
duration of time elapses without
the machine being used when
the power is on. All lights except
the power save indicator go off.
To resume normal operation,
press the [START] key (
).
Normal operation also resumes
automatically when a print job is
received or scanning is begun
from a computer. While in auto
power shut-off mode, no keys
(except the [START] key (
))
can be used.
1: PATTERN 1
2: PATTERN 2
• Use this setting to select the
layout pattern when two original
pages are copied onto a single
sheet of paper (see page 35 for
the layout patterns).
1: ON
2: OFF
• When enabled, this function
offsets the position of each
set of copies in the output tray
in copy mode, and each print
job in printer mode.
1: ON
2: OFF
• When two-sided copying is
performed, this function rotates
the image on the back of the
original. This is convenient
when binding the copies at the
top (tablet binding).
1: 300dpi
2: 600dpi
• This setting is used to change
the copy resolution in AUTO and
TEXT mode from 600 x 300 dpi
to 600 x 600 dpi (high-quality
mode). Scanning is slower
when high-quality mode is used.
7
63
!AL-2050CS.book
64 ページ
2008年1月7日 月曜日 午後8時10分
USER SETTINGS
Program
number
Setting codes
(factory default
setting appears
in bold)
Explanation
11
2-SIDED COPY
MODE
1: HI-SPEED
2: NORMAL
• If the memory fills up when
two-sided copying is
performed, "NORMAL" can be
selected to make copying
possible. However,
"NORMAL" results in a slower
copying speed. Normally "HISPEED" is selected to enable
fast two-sided copying.
12
MARGIN WIDTH
1: 1/4"
2: 1/2"
3: 3/4"
4: 1"
• Use this setting to set the
margin width.
13
MEM. FOR
PRINTER
1: 30%
2: 40%
3: 50%
4: 60%
5: 70%
• Use this to change the
proportion of machine
memory used for printer
mode.
AUTO KEY
REPEAT
1: ON
2: OFF
• Use this setting to select
whether or not holding down a
key causes repeated input of
the key. For keys that normally
cause a set value to decrease
or increase when held down
(for example, the [
] key
(
) or [
] key (
)), this
program can be used to have
the set value not change
when the key is held down.
15
KEY PRESS TIME
1: NORMAL
2: 0.5 SEC.
3: 1.0 SEC.
4: 1.5 SEC.
5: 2.0 SEC.
• Use this setting to select how
long a key must be pressed
for the input to be accepted.
By selecting a longer time,
you can prevent settings from
being changed by the
accidental pressing of a key.
16
KEY TOUCH
SOUND
1: LOW
2: HIGH
3: OFF
• This sets the volume of beep
signals. (p.68)
17
SOUND AT
DEFAULT
1: ON
2: OFF
• Use this to sound a beep
when a base setting is
selected. (p.68)
1: ON
2: OFF
• This mode reduces toner
usage by about 10% when
copying. Toner save mode is
effective when the exposure
mode is AUTO or TEXT.
14
18
64
Program name
TONER SAVE
MODE
!007-user settings.fm 65 ページ
2008年5月23日 金曜日 午後3時39分
USER SETTINGS
Program
number
19
Program name
Setting codes
(factory default
setting appears
in bold)
1: SPF/RSPF
(Adjustment to
5 levels is
possible.)
AE LEVEL ADJUST 2: DOCUMENT
GLASS
(Adjustment to
5 levels is
possible.)
Explanation
• This is used to adjust the
exposure level.
• The automatic exposure level can
be adjusted separately for the
document glass and the RSPF.
• For the procedure for adjusting
the exposure and guidelines
for numeric values, see page
28. The factory default setting
for the exposure level is center.
20
LANGUAGE
1: AMERICAN
ENGLISH
2: ENGLISH
3: FRENCH
4: SPANISH
21
RESET FACTORY
1: YES
2: NO
• This is used to return all settings
to the factory default settings.
22
SORT AUTO
SELECT
1: ON
2: OFF
• Use this setting to enable or
disable sort auto select mode.
1: ON
2: OFF
• You can set the operation that
takes place if the [START] key
(
) is pressed when the
RSPF is not completely closed.
(For details on the "Check RSPF
open function", see page 25.)
1: 8.5x11
2: 5.5x8.5
• Set the allowed paper sizes
for copying from the bypass
tray. When "5.5x8.5" is
selected, a copy of a letter
size original will only be
printed up to invoice size.
24
25
CHECK RSPF
OPEN
VALID COPY
WIDTH
• This is used to set the
language used in the display.
28
LSU SETTING
1: ON
2: OFF
• Select whether copying is only
allowed when the polygon
motor is rotating, or also when
the polygon motor is stopped.
29
PAPER TYPE
1: PLAIN PAPER
2: HEAVY PAPER
• Set the temperature of the
fusing unit when the bypass
tray is used.
30
DISPLAY
CONTRAST
1: LIGHTER
2: LIGHT
3: NORMAL
4: DARK
5: DARKER
• Set the contrast of the display.
7
65
!AL-2050CS.book
66 ページ
2008年1月7日 月曜日 午後8時10分
USER SETTINGS
Print mode
Program
number
1
2
3
Program name
Setting codes
(factory default
setting appears
in bold)
Explanation
• When this function is enabled,
printing in printer mode will
automatically continue using a
different size of paper if the
specified size of paper runs
out in all trays. This feature
does not function in copy
mode.
FORCED
OUTPUT
1: ON
2: OFF
USB 2.0 MODE
SWITCH*
• This sets the USB 2.0 data
transfer speed. To obtain the
fastest speed when using the
USB 2.0 connector, first verify
that your computer meets the
system requirements
(operating system and driver),
and then use this program to
1: FULL-SPEED
change the USB 2.0 mode to
2: HI-SPEED
"Hi-Speed". Note that the
setting should not be changed
while running a TWAIN driver.
(For the system requirements,
see "System requirements for
USB 2.0 (Hi-Speed mode)"
(p.57).)
AUTO TRAY
SWITCH
1: ON
2: OFF
• If the paper runs out during
printing and there is paper of
the same size in another tray,
this function automatically
switches to that tray
(excluding the bypass tray).
The function can be disabled.
* The scanning speed increases when the USB 2.0 mode is set to "HI-SPEED",
however, the printing speed does not increase considerably.
66
!AL-2050CS.book
67 ページ
2008年1月7日 月曜日 午後8時10分
SELECTING A SETTING FOR A USER PROGRAM
1
Press the [MENU] key and then press the
[ENTER] key.
MAIN MENU
1:USER PROGRAM
In printer mode, the user programs are accessed
by simply pressing the [MENU] key.
2
Press the [ ] key ( ) or [ ] key ( ) to
select the item that you wish to configure
in the USER PROGRAM items, and then
press the [ENTER] key.
USER PROGRAM
2:PREHEAT MODE
• See "USER PROGRAM" (p.62 to p.66)
for the program name and program
code.
• You can also select a program by
directly entering the program number
with the numeric keys.
3
Press the [ ] key ( ) or [ ] key ( ) to
change the setting of the selected item.
PREHEAT MODE
1:1 MIN
See "USER PROGRAM" (p.62 to p.66) for the
program code.
Note
4
• If you mistakenly select the wrong item, press the [CLEAR] key
(
) and repeat the procedure from step 2.
• To cancel a setting for a user program, press the [MENU] key.
Press the [ENTER] key.
Your selection appears briefly and then the previous screen appears.
Note
7
When "AE LEVEL ADJUST" is selected in the user programs and the
[ENTER] key is pressed, the automatic exposure adjustment screen
appears. Adjust the exposure and press the [ENTER] key.
67
!AL-2050CS.book
68 ページ
2008年1月7日 月曜日 午後8時10分
USER SETTINGS
Audible signals (key entry beep, invalid key beep, base setting beep)
The machine sounds three different types of beep signals: a key entry beep that
sounds when a valid key is pressed, an invalid key beep that sounds when an
invalid key is pressed, and a base setting beep that sounds when a setting is the
same as the base setting (base settings are explained below). The base setting
beep is initially disabled. If you wish to enable the base setting beep, see
"SOUND AT DEFAULT" on page 64. If you wish to change the volume of the beep
signals or disable them, see "KEY TOUCH SOUND" on page 64.
The beep patterns of each type of beep signal are as follows:
Key entry beep..................... One beep
Base setting beep........... Three beeps
Invalid key beep............... Two beeps
Base settings
The base settings are preset standard selections for each copy setting. The base
settings are as follows:
Copy ratio................................... 100%
Light and Dark level ................. Center
68
Paper feed location ................. Tray 1
(Upper paper tray)
AUTO/TEXT/PHOTO ................AUTO
!AL-2050CS.book
8
69 ページ
2008年3月18日 火曜日 午後7時40分
Chapter 8
TROUBLESHOOTING AND
MAINTENANCE
Problems related to general use of the machine, the copy function, and software
setup are explained here. Be sure to check the problem carefully before calling for
service, as many problems can be solved by the user.
If you are unable to solve the problem, turn off the main switch, unplug the power
cord from the outlet, and contact your dealer.
Note
For problems related to the printer and scanner functions, see the
online manual.
DISPLAY MESSAGES
When the following indicators light up or blink on the operation panel or the following
alphanumeric codes appear in the display, solve the problem immediately referring
to both the table below and the indicated page.
Note
Be sure to use only genuine SHARP parts and supplies.
Indication
Lamp indicator
Display
BYPASS : ADD
PAPER
Tray
location Blinks TRAY<*> : ADD
PAPER
indicator
CLOSE PAPER
TRAY<*>
CLEAR PAPER
JAM.
SPF/RSPF JAM.
FRONT OR SIDE
COVER OPEN.
CLOSE COVERS.
CLOSE THE SPF/
RSPF COVER.
Error
Blinks
indicator
Cause and remedy
Page
The indicated paper tray is not
attached, is attached incorrectly, or has
run out of paper. (The tray is indicated
in <*>.)
19
A paper misfeed has occurred.
Remove the misfeed as explained in
"MISFEED REMOVAL".
78
The cover is open. Close the cover.
-
The document feeder cover is open.
Close the document feeder cover.
The
TD (Toner/Developer) cartridge is
REPLACE THE TD
empty. Replace the TD cartridge with a
CARTRIDGE.
new cartridge.
When [L1-00] appears, the scan head
locking switch is locked. Turn off the
power, release the scan head locking
switch, and turn the power back on.
SYSTEM ERROR
[XX - XX] REFER The machine will not function. Turn the
TO USER GUIDE power switch off, wait about 10 seconds,
and then turn on the switch again. If this
does not clear the error, remove the
power cord from the outlet, and contact
your SHARP service center.
82
8
13
-
69
!AL-2050CS.book
70 ページ
2008年1月7日 月曜日 午後8時10分
TROUBLESHOOTING AND MAINTENANCE
Indication
Lamp indicator
Display
Cause and remedy
The TD (Toner/Developer) cartridge is
not installed correctly. Reinstall the TD
cartridge.
Blinks
REPLACE THE
The drum cartridge has reached the
DRUM
end of its life. Replace it with a new
Error
CARTRIDGE.
drum cartridge.
indicator
TD CARTRIDGE Toner is low. Purchase a new TD
IS NEAR EMPTY. (Toner/Developer) cartridge.
Steadily
A
DRUM
Less than 1000 sheets can be printed
lit
CARTRIDGE WILL with the current drum cartridge.
BE NEEDED SOON. Purchase a new drum cartridge.
MEMORY FULL, PRESS START TO
Data is being held in memory. Print the
RESUME.
data or clear it from memory.
NO 2-SIDED COPY FROM BYPASS
Two sided printing or 2 IN 1 copying is
TRAY.
selected when the bypass tray is
already selected ,or the bypass tray is
selected when two-sided printing or 2
IN 1 copying is already selected.
NO 2IN1 COPY FROM
The bypass tray cannot be used. Press
BYPASS TRAY.
the [TRAY SELECT] key (
) to select
a paper tray.
2 IN 1 copy and margin shift cannot be
NO 2IN1 COPY WITH MARGIN SHIFT. used in combination. Cancel the
function that was selected last.
COPY RATIO CAN NOT BE
Copy ratio can not be changed in 2 IN
CHANGED IN 2IN1.
1 copy.
This
appears if you attempt to change
THIS MENU IS NOT SELECTABLE
a user program setting while a print job
WITH DATA.
is in progress.
There is no paper for printing. Press
the [MODE SELECT] key to switch to
printer mode and follow the instructions
NO XXXX SIZE TRAY
in the display.
("XXXX" indicates paper size)
An original remains on the document
glass, or the original is too thick to
scan. Remove the original.
CHECK SPF/RSPF.
If the message is not cleared when there
START TO RESUME.
is no original on the document glass, the
underside of the RSPF is dirty. Clean the
underside of the RSPF. (especially areas
where black lines appear.)
Printing is not possible if the paper size
setting is different from the size of
paper loaded in the tray. Load the
same size of paper as the paper size
LOAD XXXX PAPER INTO TRAY<*>.
setting and then press the [START] key
( ). Printing will begin.
("XXXX" indicates paper size. The tray
is indicated in <*>.)
The machine is not correctly connected
NO PC COMMUNICATION; CHECK
to the computer. Check the cable
CABLE.
(when using the scanner function).
INSTALL A TD
CARTRIDGE.
70
Page
82
84
82
84
34
30
35
35
38
29
35
62
-
25
87
19
46
!AL-2050CS.book
71 ページ
2008年1月7日 月曜日 午後8時10分
TROUBLESHOOTING THE MACHINE
The following problems are related to the general operation of the machine and
copying.
Problem
Cause and solution
Page
The machine is not plugged into a
power outlet.
→ Plug the machine into a grounded outlet.
-
Power switch OFF.
→ Turn the power switch ON.
The machine does not
operate.
Copies are too dark or
too light.
Blank copies.
16
The power save indicator is blinking.
Indicates that the machine is warming
up.
→ Copies cannot be made until the
machine has finished warming up.
-
The front cover or the side cover is not
completely closed.
→ Close the front cover or the side cover.
-
The machine is in auto power shut-off
mode.
→ In auto power shut-off mode, all lights
are off except the power save indicator.
Press the [START] key (
) to resume
normal operation.
17
The scan head locking switch is locked.
→ Unlock the scan head locking switch.
13
Select the correct original type for the
original.
→ Select AUTO with the [EXPOSURE] key
or press the [
] key (
) or [
] key
(
) to manually select an appropriate
exposure.
→ If the copy is too light or too dark even
though AUTO was selected with the
[EXPOSURE] key, adjust the automatic
exposure level.
28
65
The original is not placed face up in the
RSPF or face down on the document
glass.
→ Place the original face up in the RSPF
or face down on the document glass.
24, 25
The scan head locking switch is locked.
→ Unlock the scan head locking switch.
13
8
71
!AL-2050CS.book
72 ページ
2008年1月7日 月曜日 午後8時10分
TROUBLESHOOTING AND MAINTENANCE
Problem
Cause and solution
The original was not placed in the
correct position.
→ Place the original correctly.
Part of the image is cut
off or there is too much
blank space.
Wrinkles appear in the
paper or the image
disappears in places.
Copies are smudged or
dirty.
72
Page
24, 25
An appropriate ratio was not used for
the size of the original and the size of
the paper.
→ Press the [COPY RATIO] key to change
the ratio to a setting that is suitable for
the original and the copy paper.
29
The size of paper loaded in the tray was
changed without changing the tray's
paper size setting.
→ Be sure to change the tray's paper size
setting whenever you change the size
of paper loaded in the tray.
23
The paper is outside of the specified
size and weight range.
→ Use copy paper within the specified
range.
18
Paper curled or damp.
→ Do not use curled or crimped paper.
Replace with dry copy paper. During
periods when the machine is not used
for a long time, remove the paper from
the tray and store it in a dark place in a
bag to prevent moisture absorption.
-
The document glass or the underside of
the RSPF is dirty.
→ Clean regularly.
87
Original smudged or blotchy.
→ Use a clean original.
-
Images rub off the copy
easily.
The fusing temperature is not
appropriate.
→ In the user programs, set "PAPER
TYPE" (program 29) to "2 (HEAVY
PAPER)".
65
Printing is not uniform
between the edges of
the paper and the
center.
The fusing temperature is not
appropriate.
→ In the user programs, set "PAPER
TYPE" (program 29) to "1 (PLAIN
PAPER)".
65
!AL-2050CS.book
73 ページ
2008年1月7日 月曜日 午後8時10分
TROUBLESHOOTING AND MAINTENANCE
Problem
Cause and solution
Page
Misfeed occur.
→ To remove the misfeed, see "MISFEED
REMOVAL".
78
The paper is outside of the specified
size and weight range.
→ Use copy paper within the specified
range.
18
Paper curled or damp.
→ Do not use curled or crimped paper.
Replace with dry copy paper. During
periods when the machine is not used
for a long time, remove the paper from
the tray and store it in a dark place in a
bag to prevent moisture absorption.
Paper misfeed.
White or black lines
appear on copies.
-
Paper is not loaded properly.
→ Make sure that the paper is properly
loaded.
19
Pieces of paper inside machine.
→ Remove all pieces of misfed paper.
79
Too much paper is loaded in the tray.
→ If the stack of paper is higher than the
indicator line on the tray, remove some
of the paper and reload so that the
stack does not exceed the line.
19
Some sheets of paper stick together.
→ Fan the paper well before loading it.
19
The guides on the bypass tray do not
match the width of the paper.
→ Adjust the guides to match the width of
the paper.
22
The bypass tray extension is not
opened.
→ When loading a large size of paper,
open the extension.
22
The scanner glass for the RSPF is dirty.
→ Clean the long, narrow scanning
window.
87
The TD (Toner/Developer) cartridge or
drum cartridge is dirty.
→ Clean the TD cartridge or drum
cartridge.
88
The transfer charger is dirty.
→ Clean the transfer charger.
89
8
73
!008-troubleshooting.fm
74 ページ
2008年1月11日 金曜日 午前9時1分
TROUBLESHOOTING AND MAINTENANCE
Problem
Cause and solution
Copying or printing is performed.
→ Set the paper size after copying or
printing is complete.
Paper size for a paper
tray cannot be set.
Output does not stack
neatly in the paper
output tray.
A copy job stops before
it is finished.
The power save
indicator is lit.
Error indicator (
lit or blinking.
) is
Lighting fixture flickers.
74
Page
-
The machine has stopped temporarily
due to running out of paper or a
misfeed.
→ Load paper or remove the misfeed, and
then set the paper size.
19, 23,
78
Both ends of the paper are curled
upward.
→ Turning the paper over in the paper tray
may help.
19
"MEMORY FULL, PRESS START TO
RESUME." appears in the display.
→ The memory became full during sort
copy. Copy only the originals that have
been scanned to that point, or cancel
the job and clear the data from memory.
34
The tray is out of paper.
→ Load paper.
19
Other indicators are lit.
→ If other indicators are lit, the machine is
in preheat mode. Press any key on the
operation panel to resume normal
operation.
17
Only the power save indicator is lit.
→ If only the power save indicator is lit, the
machine is in auto power shut-off
mode. Press the [START] key (
) to
resume normal operation.
17
See "DISPLAY MESSAGES" to check the
meaning of the error indicator and error
message in the display, and take
appropriate action.
69
The same power outlet is used for the
lighting fixture and the machine.
→ Connect the machine to a power outlet
which is not used for other electric
appliances.
-
!AL-2050CS.book
75 ページ
2008年1月7日 月曜日 午後8時10分
PROBLEMS DURING SETUP OF THE SOFTWARE
If the software does not install correctly, check the following items on your computer.
To remove the software, see "Removing the software" (p.77).
MFP driver cannot be installed (Windows 2000/XP)
If the MFP driver cannot be installed in Windows 2000/XP, follow these steps to
check your computer's settings.
1
Click the "start" button and then click "Control Panel".
In Windows 2000, click the "Start" button, select "Settings", and then click
"Control Panel".
2
Click "Performance and Maintenance", and then click
"System".
In Windows 2000, double-click the "System" icon.
3
Click the "Hardware" tab and then click the "Driver Signing"
button.
4
Check "What action do you want
Windows to take?" ("File
signature verification" in
Windows 2000).
If "Block" has been selected, it will not
be possible to install the MFP driver.
Select "Warn" and then install the MFP
driver as explained in "INSTALLING
THE SOFTWARE".
8
75
!AL-2050CS.book
76 ページ
2008年1月7日 月曜日 午後8時10分
TROUBLESHOOTING AND MAINTENANCE
Plug and play screen does not appear (USB only)
If the Plug and Play screen does not appear after you connect the machine to your
computer with a USB cable and turn on the machine, follow the steps below to verify
that the USB port is available.
1
Click the "start" button, click "Control Panel", and then click
"Performance and Maintenance".
• In Windows Vista, click the "Start" button, select "Control Panel", and then
click "System and Maintenance".
• In Windows 98/Me/2000, click the "Start" button, select "Settings", and
then click "Control Panel".
2
Click "System", click the "Hardware" tab, and click the "Device
Manager" button.
"Universal Serial Bus controllers" will appear in the list of devices.
Note
3
• In Windows 98/Me, double-click the "System" icon and click the
"Device Manager" tab.
• In Windows 2000, double-click the "System" icon, click the
"Hardware" tab, and click the "Device Manager" button.
• In Windows Vista, click the "Device Manager", and if a message
screen appears asking you for confirmation, click "Continue".
• If the "System" icon does not appear in Windows Me, click "view all
Control Panel options".
Click the
icon beside "Universal Serial Bus controllers".
Two items should appear: your controller chipset type and Root Hub. If
these items appear, you can use the USB port. If the "Universal Serial Bus
controllers" shows a yellow exclamation point or does not appear, you must
check your computer manual for USB troubleshooting or contact your
computer manufacturer.
4
76
Once you have verified that the USB port is enabled, install the
software as explained in "INSTALLING THE SOFTWARE".
!AL-2050CS.book
77 ページ
2008年1月7日 月曜日 午後8時10分
TROUBLESHOOTING AND MAINTENANCE
The MFP driver cannot be correctly installed by Plug and
Play (Windows 2000/XP/Vista) (USB only)
In Windows 2000/XP/Vista, if the MFP driver cannot be correctly installed by Plug
and Play (for example, Plug and Play takes place without copying the required files
for the MFP driver installation), follow these steps to remove unneeded devices and
then install the MFP driver as explained in "INSTALLING THE SOFTWARE" (p.40).
1
Click the "start" button, click "Control Panel", and then click
"Performance and Maintenance".
• In Windows Vista, click the "Start" button, select "Control Panel", and then
click "System and Maintenance".
• In Windows 2000, click the "Start" button, select "Settings", and then click
"Control Panel".
2
Click "System", click the "Hardware" tab, and click the "Device
Manager" button.
Note
3
• In Windows 2000, double-click the "System" icon, click the
"Hardware" tab, and click the "Device Manager" button.
• In Windows Vista, click the "Device Manager", and if a message
screen appears asking you for confirmation, click "Continue".
Click the
devices".
icon beside "Other
If "AL-XXXX" and "SHARP AL-XXXX"
appear, select and delete both of
these items.
Note
4
If "Other devices" does not appear, close the "Device Manager" window.
Install the software as explained in "INSTALLING THE
SOFTWARE".
Removing the software
If you need to remove the software, follow these steps.
1
Click the "start" button and then click "Control Panel".
In Windows 98/Me/2000, click the "Start" button, select "Settings", and then
click "Control Panel".
2
8
Click "Add or Remove Programs".
• In Windows Vista, click the "Uninstall a program".
• In Windows 98/Me/2000, double-click the "Add/Remove Programs" icon.
3
Select "SHARP AL-2050/2060 Series MFP Driver" and Button
Manager from the list, and remove the software.
For more information, refer to your operating manual or to the help files for
your operating system.
77
!AL-2050CS.book
78 ページ
2008年1月7日 月曜日 午後8時10分
MISFEED REMOVAL
When a misfeed occurs, the error indicator blinks, "CLEAR PAPER JAM" appears in
the display, and the machine stops operating. If a misfeed occurs when using the
RSPF, "RETURN X ORIGINAL(S) START TO RESUME" will appear in the display.
("X" indicates the number of pages to be returned.). This indicates the number of the
originals that must be returned to the document feeder tray after a misfeed. Return
the required number of originals. This number will be cleared when copying is
resumed or the [CLEAR] key (
) is pressed. If an original misfeed occurs in the
RSPF, the machine will stop and the error indicator will blink. To remove a misfeed
from the RSPF, see "D: Misfeed in the RSPF" (p.81).
1
Open the bypass tray, and
then open the side cover.
2
Check the misfeed location. Remove the misfed paper
following the instructions for each location in the illustration
below. If the error indicator blinks, proceed to "A: Misfeed in
the paper feed area" (p.79).
If the misfed paper is seen from
this side, proceed to "C: Misfeed
in the transport area". (p.80)
If paper is misfed here, proceed to "B:
Misfeed in the fusing area". (p.79)
If paper is misfed here, proceed to "A:
Misfeed in the paper feed area". (p.79)
78
!AL-2050CS.book
79 ページ
2008年1月7日 月曜日 午後8時10分
TROUBLESHOOTING AND MAINTENANCE
A: Misfeed in the paper feed area
1
Gently remove the misfed paper from the paper feed area as
shown in the illustration. If the error indicator blinks and the
misfed paper is not visible in the paper feed area, pull out the
paper tray and remove the misfed paper. If the paper cannot be
removed, proceed to "B: Misfeed in the fusing area".
The fusing unit is hot. Do not touch the fusing unit when
Warning removing misfed paper. Doing so may cause a burn or other
injury.
Caution
2
• Do not touch the surface (green portion) of the drum cartridge when
removing the misfed paper. Doing so may damage the drum and
cause smudges on copies.
• If the paper has been fed through the bypass tray, do not remove the
misfed paper through the bypass tray. Toner on the paper may stain
the paper transport area, resulting in smudges on copies.
Close the side cover by pressing the round projections near
the side cover open button. The error indicator will go out and
the ready indicator will light up.
B: Misfeed in the fusing area
1
Lower the fusing unit release
lever.
Fusing unit release lever
8
79
!AL-2050CS.book
80 ページ
2008年1月7日 月曜日 午後8時10分
TROUBLESHOOTING AND MAINTENANCE
2
Gently remove the misfed paper
from under the fusing unit as shown
in the illustration. If the paper cannot
be removed, proceed to "C: Misfeed
in the transport area".
The fusing unit is hot. Do not touch the fusing unit when
Warning removing misfed paper. Doing so may cause a burn or other
injury.
Caution
3
• Do not touch the surface (green portion) of the drum cartridge when
removing the misfed paper. Doing so may damage the drum and
cause smudges on copies.
• Do not remove the misfed paper from above the fusing unit. Unfixed
toner on the paper may stain the paper transport area, resulting in
smudges on copies.
Raise the fusing unit release lever and then close the side
cover by pressing the round projections near the side cover
open button. The error indicator will go out and the ready
indicator will light up.
C: Misfeed in the transport area
1
Lower the fusing unit release lever.
See "B: Misfeed in the fusing area" (p.79).
2
Open the front cover.
To open the front cover, see "INSTALLING THE TD (TONER/
DEVELOPER) CARTRIDGE" (p.14).
3
80
Rotate the roller rotating
knob in the direction of the
arrow and gently remove the
misfed paper from the exit
area.
Roller rotating
knob
!AL-2050CS.book
81 ページ
2008年1月7日 月曜日 午後8時10分
TROUBLESHOOTING AND MAINTENANCE
4
Raise the fusing unit release lever, close the front cover and
then close the side cover by pressing the round projections
near the side cover open button. The error indicator will go out
and the ready indicator will light up.
When closing the covers, be sure to close the front cover securely and
Caution then close the side cover. If the covers are closed in the wrong order,
the covers may be damaged.
D: Misfeed in the RSPF
If the misfed original is at the top of the document feeder tray or in the exit area,
follow procedure (A) to remove the misfeed. If the misfed original is inside the
document feeder and is not visible, follow procedure (B).
(A) If the misfed original is at the top of the document feeder tray or in the exit
area, open the document feeder cover and pull out the original. If the
original resists your pulling, press down on the RSPF jam release lever
while pulling out the original. When finished, close the document feeder
cover.
Document feeder cover
RSPF jam release lever
(B) Open the document feeder cover. Next, open the RSPF and rotate the roller
in the direction of the arrow. If the misfed original is in the state (X), pull the
original out as it feeds out into the exit area. If the misfed original is in the
state (Y), pull the original down and out. When finished, lower the RSPF
and close the document feeder cover.
Roller
8
(X)
(Y)
Note
Open and close the RSPF to clear the error indicator. "RETURN X
ORIGINAL(S) START TO RESUME" will appear in the display. Return
the indicated number of pages to the document feeder tray. Press the
[START] key (
) to resume copying.
81
!AL-2050CS.book
82 ページ
2008年1月7日 月曜日 午後8時10分
TD (TONER/DEVELOPER) CARTRIDGE REPLACEMENT
When toner is low, the error indicator will light up and "TD CARTRIDGE IS NEAR
EMPTY." will appear in the display. For information on purchasing a new TD (Toner/
Developer) cartridge, see "ABOUT SUPPLIES AND OPTIONS" (p.90). If copying is
continued while the indicator is lit, copies will gradually become lighter until the toner
runs out. When the toner runs out, the machine will stop operating, the error indicator
will blink, and "REPLACE THE TD CARTRIDGE" will appear in the display. Follow
the procedure below to replace the TD (Toner/Developer) cartridge.
Note
82
• After the machine stops, it may be possible to make a few more
copies by taking the TD cartridge out of the machine, shaking it
horizontally, then reinstalling it. If copying is not possible after this
operation, replace the TD cartridge.
• During a long copy run of a dark original, "TONER
REPLENISHMENT IN PROGRESS" appears in the display, and the
machine may stop even though toner is left. The machine will feed
toner up to 2 minutes and then the ready indicator will light up. Press
the [START] key (
) to resume copying.
1
Open the bypass tray, and
then open the side cover
while pressing the side
cover open button.
2
Push gently on both sides of
the front cover to open the
cover.
!AL-2050CS.book
83 ページ
2008年1月7日 月曜日 午後8時10分
TROUBLESHOOTING AND MAINTENANCE
3
Gently pull the TD (Toner/Developer)
cartridge out while pressing the lock
release button.
Note
4
Lock release button
• After removing the TD cartridge, do not shake it or tap on it. Doing so
may cause toner to leak from the cartridge. Put the old cartridge
immediately in the bag contained in the box of the new cartridge.
• Dispose of the old TD cartridge in accordance with local regulations.
Remove the TD (Toner/Developer) cartridge from the bag.
Remove the protective paper. Hold the cartridge on both sides
and shake it horizontally four or five times. Hold the tab of the
protective cover and pull the tab to your side to remove the
cover.
4 or 5 times
5
While pushing the lock release
button, gently insert the TD (Toner/
Developer) cartridge until it locks
into place.
Lock release button
8
83
!AL-2050CS.book
84 ページ
2008年1月7日 月曜日 午後8時10分
TROUBLESHOOTING AND MAINTENANCE
6
Close the front cover and
then the side cover by
pressing the round
projections near the side
cover open button. The error
indicator will go out and the
ready indicator will light up.
7
When closing the covers, be sure to close the front cover securely and
Caution then close the side cover. If the covers are closed in the wrong order,
the covers may be damaged.
DRUM CARTRIDGE REPLACEMENT
The useful life of the drum cartridge is approximately 18,000 copies*. When the
internal counter reaches approximately 17,000 copies, the error indicator will light up
and "A DRUM CARTRIDGE WILL BE NEEDED SOON" will appear in the display.
For more information on purchasing a drum cartridge, see "ABOUT SUPPLIES AND
OPTIONS" (p.90). When the error indicator blinks and "REPLACE THE DRUM
CARTRIDGE" appears in the display, the machine will stop operating until the
cartridge is replaced. Replace the drum cartridge at this time.
* Based on copying onto letter size paper at 5% toned area.
Note
1
84
Do not remove the protective cover on the drum portion (black paper) of
a new drum cartridge before use. The cover protects the drum against
external light.
Remove the TD (Toner/Developer) cartridge (see "TD (TONER/
DEVELOPER) CARTRIDGE REPLACEMENT" (p.82)).
!AL-2050CS.book
85 ページ
2008年1月7日 月曜日 午後8時10分
TROUBLESHOOTING AND MAINTENANCE
2
Hold the drum cartridge handle
and gently pull the cartridge out.
Dispose of the old drum cartridge
in accordance with local
regulations.
3
Remove the new drum cartridge from the protective bag and
remove the protective cover from the cartridge. Gently install
the new drum cartridge.
Note
Drum cartridge handle
Do not touch the surface of the drum (green portion).
Doing so may cause smudges on the copies.
4
Gently install the TD (Toner/Developer) cartridge. To install the
TD cartridge, see "INSTALLING THE TD (TONER/DEVELOPER)
CARTRIDGE" (p.14).
5
Close the front cover and then the side cover by pressing the
round projections near the side cover open button. The drum
replacement required error indicator will go out and the ready
indicator will light up.
Note
When closing the covers, be sure to close the front cover securely and
then close the side cover. If the covers are closed in the wrong order,
the covers may be damaged.
8
85
!AL-2050CS.book
86 ページ
2008年1月7日 月曜日 午後8時10分
CHECKING THE TOTAL COUNT AND DRUM
CARTRIDGE LIFE
You can check the total number of pages output by the machine (all pages printed by
the copy function and printer function), as well as the output counts of each function
(number of copies, number of scanned pages, etc.) and drum cartridge life. When a
count reaches 999,999 it returns to 0.
1
Press the [MENU] key.
Press the [ ] key ( ) or [ ] key ( )
until "TOTAL COUNT" appears, and then
press the [ENTER] key.
2
Press the [ ] key ( ) or [ ] key (
display the count of each function.
) to
MAIN MENU
3:TOTAL COUNT
TOTAL OUTPUT
The count of each function changes as follows each the [
[
] key (
)is pressed:
• "TOTAL OUTPUT":
• "COPIES":
• "SPF/RSPF":
•
•
•
•
86
012,345
] key (
) or
Total number of pages output by the machine
Total number of copies
Total number of pages scanned using the
RSPF
"2-SIDED PRINT":
Total number of pages printed by two-sided
print
"PRINTS":
Total number of pages printed the printer
function
"SCAN SEND":
Total number of scans
"REMAINING DRUM LIFE": The remaining number of pages that can be
printed with the drum cartridge is displayed.
!AL-2050CS.book
87 ページ
2008年1月7日 月曜日 午後8時10分
CLEANING THE MACHINE
Proper care is essential in order to get clean, sharp copies. Be sure to take a few
minutes to clean the machine on a regular basis.
Do not spray flammable cleaner gas. Gas from the spray may
Warning come in contact with the internal electrical components or hightemperature parts of the fusing unit, creating a risk of fire or
electrical shock.
Caution
• Before cleaning, be sure to turn the power switch off and remove
the power cord from the outlet.
• Do not use thinner, benzene or other volatile cleaning agents.
Doing so may cause deformation, discoloration, deterioration or
malfunction.
Cabinet
Wipe the cabinet with a soft, clean cloth.
Document glass and the back side of the RSPF
Stains on the glass, RSPF scanning window, cover or RSPF roller will also be
copied. Wipe the glass, RSPF scanning window, cover and RSPF roller with a soft,
clean cloth. If necessary, dampen the cloth with a glass cleaner.
Document glass/scanning window
RSPF
RSPF roller
RSPF scanning window
Black line
8
If this area is dirty, copying from the RSPF will
not be possible.
87
!AL-2050CS.book
88 ページ
2008年1月7日 月曜日 午後8時10分
TROUBLESHOOTING AND MAINTENANCE
TD (Toner/Developer) cartridge and drum cartridge
1
Remove the TD (Toner/Developer) cartridge and drum cartridge
as explained in "TD (TONER/DEVELOPER) CARTRIDGE
REPLACEMENT" (p.82) and "DRUM CARTRIDGE
REPLACEMENT" (p.84).
2
Wipe the parts of the TD (Toner/Developer) cartridge and drum
cartridge shown below with a clean cloth.
Wipe only the parts that are indicated in the illustration.
Caution
3
• Do not touch the surface of the drum (green portion).
Doing so may cause smudges on the copies.
• When cleaning the TD cartridge, do not tilt or shake it. Toner may
spill out and soil your clothes.
Replace the TD (Toner/Developer) cartridge and drum cartridge
as explained in "TD (TONER/DEVELOPER) CARTRIDGE
REPLACEMENT" (p.82) and "DRUM CARTRIDGE
REPLACEMENT" (p.84).
If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean
the charger using the following procedure.
88
!AL-2050CS.book
89 ページ
2008年1月7日 月曜日 午後8時10分
TROUBLESHOOTING AND MAINTENANCE
Transfer charger
1
Turn the power switch off. (p.17)
2
Ensure that the bypass tray is open and then open the side
cover while pressing the side cover open button. (p.14)
3
Take the charger cleaner out by holding the tab. Set the charger
cleaner onto the right end of the transfer charger, gently slide
the cleaner to the left end, and then remove it. Repeat this
operation two or three times.
Note
Slide the charger cleaner from the right end to the left end along the
groove of the transfer charger. If the cleaner is stopped on the way,
smudges on copies may occur.
4
Return the charger cleaner
to its original position.
Close the side cover by
pressing the round
projections near the side
cover open button.
5
Turn the power switch on. (p.16)
8
89
!AL-2050CS.book
90 ページ
2008年1月7日 月曜日 午後8時10分
ABOUT SUPPLIES AND OPTIONS
When ordering supplies, please use the correct part numbers as listed below.
Note
Be sure to use only genuine SHARP parts and supplies.
For best copying results, be sure to use only SHARP Genuine Supplies
which are designed, engineered, and tested to maximize the life and
performance of SHARP copiers. Look for the Genuine Supplies label on
the toner package.
Supply list
Supply
Part number
Usable life
TD (Toner/Developer)
cartridge
AL-110TD
Approx. 4,000 sheets
Drum cartridge
AL-100DR
Approx. 18,000 sheets
* Based on copying onto letter-type paper at 5% toned area
(The life of the TD cartridge which has been included in the machine at the factory
is approximately 2,000 sheets.)
Interface cable
Please purchase the appropriate cable for your computer.
USB interface cable
USB cable that supports USB 2.0.
LAN interface cable
Shielded type cable.
90
!AL-2050CS.book
9
91 ページ
2008年1月7日 月曜日 午後8時10分
Chapter 9
APPENDIX
SPECIFICATIONS
Model
AL-2050CS
Type
Digital Multifunctional System, Desktop
Photoconductive
type
OPC drum
Document glass
type
Fixed
Copy/printing
system
Dry, electrostatic transfer
Originals
Sheets, bound documents
Originals size
Max. 8-1/2" x 14"
Copy size
Max. 8-1/2" x 14"
Min. 3-1/2" x 5-1/2"
Image loss: Max. 11/64" (4 mm) (leading and trailing edges)
Max. 3/16" (4.5 mm) (along other edges in total)
Copying speed*1
20 copies/min.
(8-1/2" x 11", one-sided copying at 100% copy ratio)
Continuous copy
Max. 99 copies; subtractive counter
First-copy
time*2
8.0 seconds (When user program 24 is set to OFF)
10.7 seconds (When user program 24 is set to ON)
(paper: 8-1/2" x 11", exposure mode: AUTO,
copy ratio: 100%)
Warm-up time*3
Approx. 0 sec.
Copy ratio
Document glass:
Variable: 25% to 400% in 1% increments (total 376 steps)
Fixed preset: 25%, 50%, 64%, 78%, 100%, 129%, 200%,
400%
RSPF:
Variable: 50% to 200% in 1% increments (total 151 steps)
Fixed preset: 50%, 64%, 78%, 100%, 129%, 200%
Exposure system
Document glass: Moving optical source, slit exposure
(stationary platen) with automatic
exposure function
RSPF:
Moving original
Paper feed
Two automatic feeding paper trays (250 sheets each) +
bypass tray (50 sheets)
9
91
!AL-2050CS.book
92 ページ
2008年3月18日 火曜日 午後7時40分
APPENDIX
Fusing system
Heat rollers
Developer system
Magnetic brush development
Light source
Cold cathode fluorescent lamp
(CCD: 3 components; R, G, and B)
Resolution
Scan: 600 x 300 dpi Output: 600 x 600 dpi(AUTO/TEXT mode)
Scan: 600 x 600 dpi Output: 600 x 600 dpi(PHOTO mode)
Gradation
256 tones (8 bits)
Power supply
120 V, 60 Hz, 8.0 A
Power consumption Max. 1.0 kW
Space requirements
31.6" (W) x 17.6" (D) (802 mm (W) x 445 mm (D))
(with trays extended)
Weight*4
Approx. 51.2 lbs. (23.2 kg)
Dimensions
20.4" (W) x 17.6" (D) x 18.1" (H)
(518 mm (W) x 445 mm (D) x 459 mm (H))
Operating
conditions
Temperature: 50°F to 86°F (10°C to 30°C)
Humidity: 20% to 85%
Noise level
Sound Power Level LwA(1B=10dB)
Copying: 6.2[B]
Standby: 3.2[B]
Sound Pressure Level LpA (bystander positions)
Copying: 48[dB(A)]
Standby: 17[dB(A)]
Sound Pressure Level LpA (operator position)
Copying: 52[dB(A)]
Standby: 17[dB(A)]
Noise emission measurement in accordance with ISO 7779.
Emission
concentration
(measured
according to RALUZ122 : Edition Jun.
2006)
Ozone: 1.5 mg/h or less
Dust: 4.0 mg/h or less
Styrene: 1.0 mg/h or less
Benzene: 0.05mg/h or less
TVOC(Printing): 10mg/h or less
TVOC(Pre-Operating): 1mg/h or less
*1 When making multiple duplex copies, the copy speed will vary based on the
environment conditions.
*2 The first-copy time is measured after the power save indicator turns off following
power on, using the document glass with the polygon rotating in the copy ready
state and "LSU SETTING" set to ON in the user programs (8-1/2" x 11", paper fed
from paper tray).
The first-copy time may vary depending on machine operating conditions and
ambient conditions such as temperature.
The time from power on until the first copy is output varies depending on the
installation site and the state of the machine in use.
*3 The warm-up time may vary depending on machine operating conditions and
ambient conditions such as temperature.
*4 Not including TD and drum cartridges.
92
!AL-2050CS.book
93 ページ
2008年1月7日 月曜日 午後8時10分
APPENDIX
Printer Function
Print speed*1
20 ppm
Resolution
600 dpi
Memory
Approx. 30 MB
Emulation
SPLC (Sharp Printer Language with Compression)
Interface
10BASE-T Network Interface*2
USB 2.0 (Full-Speed/Hi-Speed compatible interface)
Interface cables
[USB cable]
USB cable that supports USB 2.0.
Please purchase a commercially available USB cable.
[LAN cable]
Shielded type cable
Please purchase a commercially available LAN cable.
*1 When printing same document continuously on 8-1/2" x 11" plain paper in nonoffset mode, excluding processing time.
*2 Cannot be connected to an exclusive 100BASE hub.
9
93
!AL-2050CS.book
94 ページ
2008年1月7日 月曜日 午後8時10分
APPENDIX
Scanner Function
94
Type
Flatbed scanner
Scanning method
Document glass/RSPF
Light source
Cold cathode fluorescent lamp
(CCD: 3 components; R, G, and B)
Resolution
Basic: 600 dpi x 1200 dpi
Setting range: 50dpi - 9600dpi
Original types
Sheet media, books
Effective scanning
area
8.5" (216 mm) (Lengthwise) x 14" (356 mm) (Width)
Scanning speed
2.88 msec/line
Input Data
1 bit or 12 bit
Output Data
R.G.B 1 or 8 bits / pixel / A/D 16 bit
Scanning colors
Black and white 2 value, Grayscale, Full color
Protocol
TWAIN
WIA (Windows XP/Vista only)
STI
Interface
USB 2.0 (Full-Speed/Hi-Speed compatible interface)
Drop out color
Yes
Supported
operating systems
Windows 98/Me/2000 Professional/XP/Vista
(Detailed information can be found in "BEFORE
INSTALLATION" (p.41))
Void area
None
Interface cables
[USB cable]
USB cable that supports USB 2.0.
Please purchase a commercially available USB cable.
Scanner utilities
Button Manager / Sharpdesk
!AL-2050CS.book
95 ページ
2008年1月7日 月曜日 午後8時10分
IMPORTANT SERVICE INFORMATION (U.S.A. only)
If a Problem Occurs
Most operational questions can be answered by referring to the Operation Manual or Online Manual.
Also, for your convenience, you will find answers to frequently asked questions on our website at
www.sharpusa.com. You can also e-mail your service question to
www.digitalcopiersupport@sharpsec.com. Should you require further assistance, call Sharp at 1-630378-3590. A Customer Relations Specialist will assist you. Before your call, please be ready to provide
the model number of your Product, Serial Number, Date of Purchase, description of the problem, and a
valid Credit Card Number (should it be required).
How Warranty Repair Service is Obtained
Our Customer Relations Specialists at 1-630- 378-3590 will explain how to obtain warranty repair
service. Please be sure to retain the original packaging materials in order to facilitate shipment.
The shipment of the defective unit will be at your expense; please be sure it is insured and packaged
securely. Upon repair of your unit, Sharp will promptly return it to you at any U.S. location.
What You Must Do
Your Product is designed to perform with a minimum amount of user maintenance. However, you are
responsible for the required user maintenance described in the Operation Manual. This requires user
maintenance including replacement of the TD cartridge and drum cartridge, cleaning of the unit and
transfer charger, removal of dust and foreign matter, clearing of paper misfeeds, and proper routine and
preventive maintenance.
Service After Expiration of Warranty Coverage
Should you require service repair after warranty coverage has expired, contact Sharp at 1-630-378-3590
for information.
95
!AL-2050CS.book
96 ページ
2008年1月7日 月曜日 午後8時10分
END-USER LIMITED WARRANTY (Valid in U.S.A. only)
SHARP ELECTRONICS CORPORATION warrants to the first end-user purchaser that this Sharp brand
product (the "Product"), when shipped in its original container, will be free from defective workmanship
and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product
or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for
the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s)
set forth below nor to any Product the exterior of which has been damaged or defaced, which has been
subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or
modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth
below and provide proof of purchase to the servicer.
To the extent permitted by applicable state law, the warranties set forth herein are in lieu of, and exclusive
of, all other warranties, express or implied. Specifically, ALL OTHER WARRANTIES OTHER THAN
THOSE SET FORTH ABOVE ARE EXCLUDED. ALL EXPRESS AND IMPLIED WARRANTIES
INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE, AND FITNESS
FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. If, under applicable state law,
implied warranties may not validly be disclaimed or excluded, the duration of such implied warranties is
limited to the period(s) from the date of purchase set forth below.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other
than those described herein, or to extend the duration of any warranties beyond the time period described
herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be
the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the
period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of
Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims,
whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in
any way responsible, for any damages or defects in the Product which were caused by repairs or attempted
repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way
responsible for any incidental or consequential economic or property damage. Some states do not allow
limits on warranties or on remedies for breach in certain transactions; in such states, the limits herein may
not apply.
Model Specific Section
96
Your Product Model Number & Description:
AL-2050CS Digital Multifunctional System
(Be sure to have this information available when you need
service for your Product.)
Warranty Period for this Product:
One (1) year on parts and one (1) year on labor from date of
purchase, except for the toner/developer cartridge and drum
cartridge supplied with the Product, which are warranted for a
period of fifteen (15) days from date of purchase. Disk media
supplied with the Product is warranted for replacement only
and limited to ninety (90) days from date of purchase.
Additional Item(s) Excluded from
The warranty does not apply to defects or damage resulting
Warranty Coverage (if any):
from improper or inadequate maintenance by the purchaser
(see Operation Manual) or the use of non-genuine Sharp
toner/developer and drum cartridges.
Where to Obtain Service:
Service is available in the United States from Sharp.
What to do to Obtain Service:
Call Sharp at 1-630-378-3590 to obtain a Return
Authorization Number and shipping instructions. A
technician will work with you on the phone and verify that
your Product needs service. Be sure to have Proof of
Purchase available.
!AL-2050CS.book
97 ページ
2008年1月7日 月曜日 午後8時10分
97
!AL-2050CS.book
98 ページ
2008年1月7日 月曜日 午後8時10分
MATERIAL SAFETY DATA SHEET
Page : 1/4
Date Revised : Mar . 1. 2007
Date Issued : Sep . 1. 2003
MSDS No. F-01231
1.PRODUCT AND COMPANY IDENTIFICATION
Product Name
: AL-1651CS/AL-1661CS/AL-1631/AL-1641CS/AL-1642CS/AL-1217D
AL-1457D/FO-DC550/AL-1655CS/
FO-55ND/AL-100TD/AL-110TD/AL-100TDN(Black Toner)
Supplier Identification : Sharp Corporation
22-22 Nagaike-cho, Abeno-ku, Osaka, Japan
Local suppliers are listed below. Please contact the nearest supplier for additional information.
Area
(Country)
(Name and Telephone Number)
U.S.A.
Sharp Electronics Corporation
Sharp Plaza, Mahwah, NJ
Telephone number for information
: 1-800-237-4277
North
Emergency telephone number
: 1-800-255-3924
America
Canada
Sharp Electronics of Canada Ltd.
Telephone number for information
: 905-890-2100
Emergency telephone number
: 1-800-255-3924
Australia
Sharp Corporation of Australia PTY. Ltd.
Oceania
No1 Huntingwood Drive Huntingwood Blacktown N.S.W.
Telephone number for information
: 1300-13-50-22
Germany
Sharp Electronics (Europe) GMBH
Sonninstrasse 3, 20097 Hamburg
Telephone number to access MSDS
: 040-2376-2185
For more information
: 040-2376-2613
United
Sharp Electronics (U. K.) Ltd.
Kingdom
Telephone number for information
: 08705-274-277
France
Sharp Electronics France S.A.
Telephone number for information
: 01-49-90-34-00
Austria
Sharp Electronics GMBH
Telephone number for information
: 01-727-19-0
Europe
Italy
Sharp Electronics (Italy) S.P.A.
Telephone number for information
: 02895951
Spain
Sharp Electronics (Espana) S.A.
Telephone number for information
: 93-581-97-00
Netherlands
Sharp Electronics Benelux B.V.
Telephone number for information
: 30-6359500
Sweden
Sharp Electronics Nordic AB
Telephone number for information
: 08-634-36-00
Switzerland
Sharp Electronics(Schweiz)AG
Telephone number for information
: 01-846-6111
U.A.E.
Sharp Middle East FZE
Middle
P.O.Box 17115 Jebel Ali, Dubai
East
Telephone number for information
: 04-815311
2.COMPOSITION / INFORMATION ON INGREDIENTS
Preparation[X]
Substance[ ]
Ingredient
Styrene-Acrylate
copolymer
Carbon black
Iron oxide
Paraffin wax
Polypropylene
98
CAS No.
Confidential
1333-86-4
1317-61-9
8002-74-2
Confidential
Proportion
85-90%
OSHA PEL
Not listed
ACGIH TLV
Not listed
MAK-TWA
Not listed
NOHSC- TWA
Not listed
5-8%
1-5%
1-3%
0.5-3%
3.5mg/m3
Not listed
Not listed
Not listed
3.5mg/m3
Not listed
Not listed
Not listed
Not listed
Not listed
Not listed
Not listed
3mg/m3
Not listed
Not listed
Not listed
!AL-2050CS.book
99 ページ
2008年1月7日 月曜日 午後8時10分
MATERIAL SAFETY DATA SHEET
Page : 2/4
Date Revised : Mar . 1. 2007
Date Issued : Sep . 1. 2003
MSDS No. F-01231
3.HAZARDS IDENTIFICATION
Most Important Hazards and Effects of the Products
Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests
performed using toner. When used as intended according to instructions, studies do not
indicate any symptoms of fibrosis will occur.
Environmental Effects : No data are available.
Specific Hazards
: Dust explosion (like most finely divided organic powders)
Directive 1999/45/EC(Europe) : Not classified as dangerous
4.FIRST-AID MEASURES
Route(s) of Entry : Inhalation?
Yes
Skin?
No
Ingestion?
Possible but very unusual.
Inhalation
: Remove to fresh air. If symptoms occur, consult medical personnel.
Skin Contact : Wash with soap and water for 15 minutes or until particle is removed.
If irritation does occur, consult medical personnel.
Eye Contact : Flush eyes immediately with water for 15 minutes. If irritation does occur, consult medical personnel.
Ingestion
: Rinse with water and drink several glasses of water. If irritation or discomfort does occur, consult
medical personnel.
5.FIRE-FIGHTING MEASURES
Extinguishing Media
: Water, CO2, foam and dry chemicals
Special Fire Fighting Procedures : None
Fire and Explosion Hazards
: Toner material, like most finely divided organic powders, may form an explosive
mixture.
6.ACCIDENTAL RELEASE MEASURES
Personal Precautions
: None
Environmental Precautions
: None
Methods for Cleaning Up
: Wipe off with paper or cloth. Do not use vacuum cleaner when a large amount is
released. It, like most finely divided organic powders, is capable of creating a
dust explosion.
7.HANDLING AND STORAGE
Handling
Technical Measures
: None
Precautions
: None
Safe Handling Advice : Use of a dust mask is recommended when handling a large quantity of toner or during long
term exposure, as with any non-toxic dust. Try not to disperse the particles.
Storage
Technical Measures
: None
Storage Conditions
: Keep container closed and Store in a cool and dry place.
Keep out of the reach of children.
Incompatible Products : None
99
!AL-2050CS.book
100 ページ
2008年1月7日 月曜日 午後8時10分
MATERIAL SAFETY DATA SHEET
Page : 3/4
Date Revised : Mar . 1. 2007
Date Issued : Sep . 1. 2003
MSDS No. F-01231
8.EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering Measures
Ventilation
: Not required under intended use.
Exposure Limit Values
OSHA-PEL(USA)
: 15mg/m3 (Total Dust), 5mg/m3 (Respirable Dust)
ACGIH-TLV(USA)
: 10mg/m3 (Total Dust), 3mg/m3 (Respirable Dust)
Personal Protective Equipment
Respiratory Protection
: Not required under intended use.
Hand Protection
: Not required under intended use.
Eye Protection
: Not required under intended use.
Skin Protection
: Not required under intended use.
Other Protective Equipment
: Use of a dust mask and goggles are recommended when handling a large
quantity of toner or during long term exposure, as with any non-toxic dust.
9.PHYSICAL AND CHEMICAL PROPERTIES
Appearance
Physical State : Solid
Form : Powder
Ph
: Not applicable
Boiling / Melting Point
: Not applicable
Softening Point(°C)
: 130͠
Flash Point(°C)
: Not applicable
Ignition Point(°C )
: No data
Explosion Properties
: No data
Density(g/cm³)
: 1.1
Solubility in Water
: Negligible
Color : Black
Odor : faint odor
10.STABILITY AND REACTIVITY
Stability
: Stable
Hazardous Reactions
: Dust explosion, like most finely divided organic powders.
Conditions to Avoid
: Electric discharge, throwing into fire.
Materials to Avoid
: Oxidizing Materials
Hazardous Decomposition Products : CO, CO2 and NOX
Further Information
: None
11.TOXICOLOGICAL INFORMATION
Acute Toxicity
Ingestion(oral)
: LD50 > 2000mg/kg (Rats)
Inhalation
: LC50>5.14mg/L㧔Rats㧕
Eye irritation
: Not an irritant (Rabbits)
Skin irritation
: Not an irritant (Rabbits)
Skin sensitizer
: No sensitization
Mutagenicity
: Negative(Ames Test).
Carcinogenicity : In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human
carcinogen). This classification is given to chemicals for which there is inadequate human
evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. The
classification is based upon the development of lung tumors in rats receiving chronic inhalation
exposures to free carbon black at levels that induce particle overload of the lung. Studies
performed in animal models other than rats did not show any association between carbon black
100
!AL-2050CS.book
101 ページ
2008年1月7日 月曜日 午後8時10分
MATERIAL SAFETY DATA SHEET
Chronic Effect
Page : 4/4
Date Revised : Mar . 1. 2007
Date Issued : Sep . 1. 2003
MSDS No. F-01231
and lung tumors. Moreover, a two-year cancer bioassay using a typical toner preparation
containing carbon black demonstrated no association between toner exposure and tumor
development in rats.
: In a study in rats of chronic inhalation exposure to a typical toner, a mild to moderate degree of
lung fibrosis was observed in 92% of the rats in the high concentration (16mg/m3) exposure
group, and a minimal to mild degree of fibrosis was noted in 22% of the animals in the middle
(4mg/m3) exposure group, but no pulmonary change was reported in the lowest (1mg/m3)
exposure group, the most relevant level to potential human exposures.
12.ECOLOGICAL INFORMATION
No data are available.
13.DISPOSAL CONSIDERATIONS
Waste from Residues
: Waste material may be dumped or incinerated under conditions which meet all federal,
state and local environmental regulations.
Contaminated Packaging : Waste may be disposed or incinerated under conditions which meet all federal, state
and local environmental regulations.
14.TRANSPORT INFORMATION
UN Classification
: None
Not classified as hazardous for transport.
15.REGULATORY INFORMATION
US Information
TSCA(Toxic Substances Control Act) :
All chemical substances in this product comply with all applicable rules or order under TSCA.
SARA(Superfund Amendments and Reauthorization Act) Title III
302 Extreme Hazardous Substance : None
311/312 Hazard Classification
: None
EU Information
1999/45/EC and 67/548/EEC
Symbol & Indication
: Not required
R-Phrase
: Not required
76/769/EEC
: All chemical substances in this product comply with all applicable rules or
order under 76/769/EEC.
16.OTHER INFORMATION
NFPA Rating (USA)
: Health=1
Flammability=1
Reactivity=0
WHMIS Legislation (Canada) : This product is not a controlled product.
References
IARC(1996) : IARC monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans, Vol. 65,
Printing Process And Printing Inks, Carbon Black and Some Nitro Compounds, Lyon, pp.149-261
H.Muhle, B.Bellmann, O.Creutzenberg, C.Dasenbrock, H.Ernst, R.Kilpper, J.C.MacKenzie, P.Morrow, U.Mohr,
S.Takenaka, and R.Mermelstein(1991) Pulmonary Response to Toner upon Chronic Inhalation Exposure in Rats.
Fundamental and Applied Toxicology 17, pp.280-299.
The information on this data sheet represents our current data and best opinion as to the proper use in handling of this
product under normal conditions. However, all materials may present unknown hazards and should be used with
caution. Although certain hazards are described herein, we do not guarantee that these are the only hazards which
exist.
101
!AL-2050CS.book
102 ページ
2008年1月7日 月曜日 午後8時10分
MATERIAL SAFETY DATA SHEET
Page : 1/4
Date Revised : Mar . 1. 2007
Date Issued : Sep . 1. 2003
MSDS No. F-31231
1.PRODUCT AND COMPANY IDENTIFICATION
Product Name
: AL-1651CS/AL-1661CS/AL-1631/AL-1641CS/AL-1642CS/AL-1217D
AL-1457D/FO-DC550/AL-1655CS/
FO-55ND/AL-100TD/AL-110TD/AL-100TDN(Black Developer)
Supplier Identification : Sharp Corporation
22-22 Nagaike-cho, Abeno-ku, Osaka, Japan
Local suppliers are listed below. Please contact the nearest supplier for additional information.
Area
(Country)
(Name and Telephone Number)
U.S.A.
Sharp Electronics Corporation
Sharp Plaza, Mahwah, NJ
Telephone number for information
: 1-800-237-4277
North
Emergency telephone number
: 1-800-255-3924
America
Canada
Sharp Electronics of Canada Ltd.
Telephone number for information
: 905-890-2100
Emergency telephone number
: 1-800-255-3924
Australia
Sharp Corporation of Australia PTY. Ltd.
Oceania
No1 Huntingwood Drive Huntingwood Blacktown N.S.W.
Telephone number for information
: 1300-13-50-22
Germany
Sharp Electronics (Europe) GMBH
Sonninstrasse 3, 20097 Hamburg
Telephone number to access MSDS
: 040-2376-2185
For more information
: 040-2376-2613
United
Sharp Electronics (U. K.) Ltd.
Kingdom
Telephone number for information
: 08705-274-277
France
Sharp Electronics France S.A.
Telephone number for information
: 01-49-90-34-00
Austria
Sharp Electronics GMBH
Telephone number for information
: 01-727-19-0
Europe
Italy
Sharp Electronics (Italy) S.P.A.
Telephone number for information
: 02895951
Spain
Sharp Electronics (Espana) S.A.
Telephone number for information
: 93-581-97-00
Netherlands
Sharp Electronics Benelux B.V.
Telephone number for information
: 30-6359500
Sweden
Sharp Electronics Nordic AB
Telephone number for information
: 08-634-36-00
Switzerland
Sharp Electronics(Schweiz)AG
Telephone number for information
: 01-846-6111
U.A.E.
Sharp Middle East FZE
Middle
P.O.Box 17115 Jebel Ali, Dubai
East
Telephone number for information
: 04-815311
2.COMPOSITION / INFORMATION ON INGREDIENTS
Preparation[X]
Substance[ ]
Ingredient
Iron powder
Styrene-Acrylate
copolymer
Carbon black
102
CAS No.
7439-89-6
Confidential
1333-86-4
Proportion
90-95%
5-10%
0.1-0.9%
OSHA PEL
Not listed
Not listed
ACGIH TLV
Not listed
Not listed
MAK-TWA
Not listed
Not listed
NOHSC- TWA
Not listed
Not listed
3.5mg/m3
3.5mg/m3
Not listed
3mg/m3
!AL-2050CS.book
103 ページ
2008年1月7日 月曜日 午後8時10分
MATERIAL SAFETY DATA SHEET
Page : 2/4
Date Revised : Mar . 1. 2007
Date Issued : Sep . 1. 2003
MSDS No. F-31231
3.HAZARDS IDENTIFICATION
Most Important Hazards and Effects of the Products
Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests
performed using toner. When used as intended according to instructions, studies do not
indicate any symptoms of fibrosis will occur.
Environmental Effects : No data are available.
Specific Hazards
: Dust explosion (like most finely divided organic powders)
Directive 1999/45/EC(Europe) : Not classified as dangerous
4.FIRST-AID MEASURES
Route(s) of Entry : Inhalation?
No
Skin?
No
Ingestion?
Possible but very unusual.
Inhalation
: Remove to fresh air. If symptoms occur, consult medical personnel.
Skin Contact : Wash with soap and water for 15 minutes or until particle is removed.
If irritation does occur, consult medical personnel.
Eye Contact : Flush eyes immediately with water for 15 minutes. If irritation does occur, consult medical personnel.
Ingestion
: Rinse with water and drink several glasses of water. If irritation or discomfort does occur, consult
medical personnel.
5.FIRE-FIGHTING MEASURES
Extinguishing Media
: Water, CO2, foam and dry chemicals
Special Fire Fighting Procedures : None
Fire and Explosion Hazards
: Toner material, like most finely divided organic powders, may form an explosive
mixture.
6.ACCIDENTAL RELEASE MEASURES
Personal Precautions
: None
Environmental Precautions
: None
Methods for Cleaning Up
: Wipe off with paper or cloth. Do not use vacuum cleaner when a large amount is
released. It, like most finely divided organic powders, is capable of creating a
dust explosion.
7.HANDLING AND STORAGE
Handling
Technical Measures
: None
Precautions
: None
Safe Handling Advice : Use of a dust mask is recommended when handling a large quantity of toner or during long
term exposure, as with any non-toxic dust. Try not to disperse the particles.
Storage
Technical Measures
: None
Storage Conditions
: Keep container closed and Store in a cool and dry place.
Keep out of the reach of children.
Incompatible Products : None
8.EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering Measures
Ventilation
: Not required under intended use.
103
!AL-2050CS.book
104 ページ
2008年1月7日 月曜日 午後8時10分
MATERIAL SAFETY DATA SHEET
Page : 3/4
Date Revised : Mar . 1. 2007
Date Issued : Sep . 1. 2003
MSDS No. F-31231
Exposure Limit Values
OSHA-PEL(USA)
ACGIH-TLV(USA)
Personal Protective Equipment
Respiratory Protection
Hand Protection
Eye Protection
Skin Protection
Other Protective Equipment
: 15mg/m3 (Total Dust), 5mg/m3 (Respirable Dust)
: 10mg/m3 (Total Dust), 3mg/m3 (Respirable Dust)
: Not required under intended use.
: Not required under intended use.
: Not required under intended use.
: Not required under intended use.
: Use of a dust mask and goggles are recommended when handling a large
quantity of toner or during long term exposure, as with any non-toxic dust.
9.PHYSICAL AND CHEMICAL PROPERTIES
Appearance
Physical State : Solid
Form : Powder
Ph
: Not applicable
Boiling / Melting Point
: Not applicable
Softening Point(°C)
: 130͠(toner)
Flash Point(°C)
: Not applicable
Ignition Point(°C )
: No data
Explosion Properties
: No data
Density(g/cm³)
:7
Solubility in Water
: Negligible
10.STABILITY AND REACTIVITY
Stability
Hazardous Reactions
Conditions to Avoid
Materials to Avoid
Hazardous Decomposition Products
Further Information
Color : Black
Odor : faint odor
: Stable
: Dust explosion, like most finely divided organic powders.
: Electric discharge, throwing into fire.
: Oxidizing Materials
: CO, CO2 and NOX
: None
11.TOXICOLOGICAL INFORMATION
Acute Toxicity
Ingestion(oral)
: LD50 > 2000mg/kg (Rats)
Inhalation
: LC50>5.14mg/L㧔Rats㧕
Eye irritation
: Not an irritant (Rabbits)
Skin irritation
: Not an irritant (Rabbits)
Skin sensitizer
: No sensitization
Mutagenicity
: Negative(Ames Test).
Carcinogenicity : In 1996 the IARC reevaluated carbon black as a Group 2B carcinogen (possible human
carcinogen). This classification is given to chemicals for which there is inadequate human
evidence, but sufficient animal evidence on which to base an opinion of carcinogenicity. The
classification is based upon the development of lung tumors in rats receiving chronic inhalation
exposures to free carbon black at levels that induce particle overload of the lung. Studies
performed in animal models other than rats did not show any association between carbon black
and lung tumors. Moreover, a two-year cancer bioassay using a typical toner preparation
containing carbon black demonstrated no association between toner exposure and tumor
development in rats.
104
!AL-2050CS.book
105 ページ
2008年1月7日 月曜日 午後8時10分
MATERIAL SAFETY DATA SHEET
Chronic Effect
Page : 4/4
Date Revised : Mar . 1. 2007
Date Issued : Sep . 1. 2003
MSDS No. F-31231
: In a study in rats of chronic inhalation exposure to a typical toner, a mild to moderate degree of
lung fibrosis was observed in 92% of the rats in the high concentration (16mg/m3) exposure
group, and a minimal to mild degree of fibrosis was noted in 22% of the animals in the middle
(4mg/m3) exposure group, but no pulmonary change was reported in the lowest (1mg/m3)
exposure group, the most relevant level to potential human exposures.
12.ECOLOGICAL INFORMATION
No data are available.
13.DISPOSAL CONSIDERATIONS
Waste from Residues
: Waste material may be dumped or incinerated under conditions which meet all federal,
state and local environmental regulations.
Contaminated Packaging : Waste may be disposed or incinerated under conditions which meet all federal, state
and local environmental regulations.
14.TRANSPORT INFORMATION
UN Classification
: None
Not classified as hazardous for transport.
15.REGULATORY INFORMATION
US Information
TSCA(Toxic Substances Control Act) :
All chemical substances in this product comply with all applicable rules or order under TSCA.
SARA(Superfund Amendments and Reauthorization Act) Title III
302 Extreme Hazardous Substance : None
311/312 Hazard Classification
: None
EU Information
1999/45/EC and 67/548/EEC
Symbol & Indication
: Not required
R-Phrase
: Not required
76/769/EEC
: All chemical substances in this product comply with all applicable rules or
order under 76/769/EEC.
16.OTHER INFORMATION
NFPA Rating (USA)
: Health=1
Flammability=1
Reactivity=0
WHMIS Legislation (Canada) : This product is not a controlled product.
References
IARC(1996) : IARC monographs on the Evaluation of the Carcinogenic Risk of Chemicals to Humans, Vol. 65,
Printing Process And Printing Inks, Carbon Black and Some Nitro Compounds, Lyon, pp.149-261
H.Muhle, B.Bellmann, O.Creutzenberg, C.Dasenbrock, H.Ernst, R.Kilpper, J.C.MacKenzie, P.Morrow, U.Mohr,
S.Takenaka, and R.Mermelstein(1991) Pulmonary Response to Toner upon Chronic Inhalation Exposure in Rats.
Fundamental and Applied Toxicology 17, pp.280-299.
The information on this data sheet represents our current data and best opinion as to the proper use in handling of this
product under normal conditions. However, all materials may present unknown hazards and should be used with
caution. Although certain hazards are described herein, we do not guarantee that these are the only hazards which
exist.
105
!AL-2050CS.book
106 ページ
2008年1月7日 月曜日 午後8時10分
INDEX
Symbols
[
[
[
] key.......................... 10, 31, 33, 36
] key ........................................... 10
] key ........................................... 10
2
2 IN 1 copy ....................................... 35
[2-SIDED COPY] key ........... 10, 31, 32
A
About the operation manuals ............. 6
Appendix .......................................... 91
Audible signals ................................. 68
Auto clear ......................................... 16
Auto power shut-off mode ................ 17
Automatic two-sided copying............ 30
B
Base setting...................................... 68
Basic procedure for printing ............. 58
Before installation ............................. 41
Button Manager ................................ 40
Button Manager scan menu ............. 60
Bypass feed...................................... 21
Bypass tray................. 9, 21, 22, 78, 82
Bypass tray paper guides ............. 9, 22
C
Cabinet ............................................. 87
Canceling a print job......................... 58
Capacity of paper output tray ........... 26
Caution
- Handling the machine.................... 4
- Label on the machine .................... 3
- Selecting an installation site .......... 3
- Using the machine......................... 3
Changing a tray's paper size
setting ............................................... 23
Charger cleaner............................ 9, 89
Checking packed components and
accessories ...................................... 12
Checking the total count and drum
cartridge life ...................................... 86
Cleaning the machine....................... 87
Cleaning the TD (Toner/Developer)
cartridge and drum cartridge ............ 88
[CLEAR ALL] key ................. 11, 16, 58
106
[CLEAR] key
............... 10, 24, 25, 27, 33, 34, 58, 78
Connecting a USB cable .................. 46
Convenient copy functions ............... 30
Conventions used in this manual and
online manual ..................................... 6
[COPY RATIO] key..................... 11, 29
D
Display.............................................. 10
Display messages ............................ 69
Document feeder cover ................ 9, 81
Document feeder tray................... 9, 25
Document glass............................ 9, 35
Drum cartridge........................ 9, 84, 88
Drum cartridge handle...................... 85
Drum cartridge replacement............. 84
E
[ENTER] key..................................... 10
Envelopes......................................... 21
Environmental information.................. 5
Error indicator....................... 10, 69, 78
[E-SORT/SP.FUN] key
............................ 10, 33, 34, 35, 37, 38
Exit area ............................................. 9
[EXPOSURE] key....................... 10, 28
Exposure value guidelines ............... 28
F
Factory default settings .................... 65
Front cover ............................. 9, 80, 82
Fusing unit release lever ........ 9, 79, 80
H
Handles .............................................. 9
Hardware and software
requirements .................................... 41
How to place the original .................. 24
How to use the online manual .......... 61
!AL-2050CS.book
107 ページ
2008年1月7日 月曜日 午後8時10分
I
O
Initial settings.................................... 16
Installing the software....................... 40
Installing the TD cartridge ................ 14
Interface cable .................................. 90
Introduction......................................... 6
IP address ........................................ 48
Offset function during sort copy........ 34
Online Manual .................................... 6
Operation in copy, printer, and scanner
modes............................................... 60
Operation manual............................... 6
Operation panel............................ 9, 10
Original guides ............................. 9, 25
Original output tray extension....... 9, 26
Original types ................................... 28
Originals that cannot be used in
the RSPF.......................................... 26
L
Labels ................................... 18, 19, 21
Language setting .............................. 16
LAN connector.............................. 9, 47
Loading paper .................................. 18
Loading paper in the bypass tray ..... 22
Loading the paper tray ..................... 19
Long edge ........................................ 30
LPR (TCP/IP) direct printing ............. 49
M
Main features...................................... 7
Making copies .................................. 24
Margin shift ....................................... 38
Margin width ..................................... 64
Memory full ....................................... 34
[MENU] key ...................................... 10
MFP driver ........................................ 40
Misfeed removal
- Misfeed in the fusing area ........... 69
- Paper feed area........................... 79
- RSPF........................................... 81
- Transport area............................. 80
Mode indicators ................................ 10
[MODE SELECT] key ....................... 10
N
Normal copying ................................ 28
Numeric keys.............................. 10, 27
P
Paper................................................ 18
Paper holder arm.......................... 9, 26
Paper output tray................................ 9
Paper output tray extension ......... 9, 26
Paper size setting............................. 23
Paper tray..................................... 9, 19
Part names ......................................... 9
Paper type ........................................ 18
Plug and play screen does not
appear .............................................. 76
Power cord ......................................... 9
Power off .......................................... 17
Power on .......................................... 16
Power save indicator ........................ 10
Power save modes........................... 17
Power switch .......................... 9, 16, 17
Preheat mode................................... 17
Preparations ....................................... 9
Preparing the machine for
installation ........................................ 12
Preset ratio ....................................... 29
Pressure plate lock........................... 19
Printer driver..................................... 40
Printer/scanner functions.................. 57
Problems during setup
of the software.................................. 75
Protective materials.......................... 13
107
!AL-2050CS.book
108 ページ
2008年1月7日 月曜日 午後8時10分
R
T
Ready indicator .................... 11, 16, 84
Recycled paper ................................ 18
Reduction/enlargement/zoom .......... 29
Removing the software..................... 77
Roller ................................................ 81
Roller rotating knob .......................... 80
ROPM............................................... 57
RSPF .................................................. 9
RSPF indicator ................................. 10
RSPF roller ....................................... 87
RSPF scanning window ................... 87
TD cartridge.................................. 9, 82
TD cartridge replacement................. 82
Thick paper....................................... 18
Transfer charger................................. 9
Transparency film................. 18, 19, 21
Tray location indicator ................. 10, 69
[TRAY SELECT] key ............ 10, 22, 27
Troubleshooting................................ 69
S
Scan head locking switch ................. 13
Scanner driver .................................. 40
Scanning from the operation panel .. 59
Scanning from your computer .......... 60
Scanning unit (scan head)................ 16
Selecting a setting for a user
program ............................................ 67
Selecting the tray.............................. 23
Set the IP address ............................ 48
Setting the number of copies............ 27
Setting up button manager ............... 53
Sharpdesk ........................................ 40
Short edge ........................................ 30
Side cover .............................. 9, 78, 82
Side cover open button ...................... 9
Sort copy .......................................... 33
Special papers.................................. 19
Specifications ................................... 91
Standard paper................................. 18
[START] key ......................... 11, 24, 25
Supply list ......................................... 90
System requirements for USB 2.0 .... 57
108
U
USB ................................ 42, 45, 57, 66
USB connector ............................. 9, 46
User programs
- Copy mode .................................. 62
- Print mode ................................... 66
User settings .................................... 62
Using the manual ............................... 6
Using the printer mode ..................... 58
Using the scanner mode .................. 59
Z
Zoom setting..................................... 29
!AL-2050CS.book
109 ページ
2008年1月7日 月曜日 午後8時10分
INDEX BY PURPOSE
Preparations
Connecting the computer
Installation the machine,
preparing .......................................... 12
Packed components and accessories,
checking ........................................... 12
Paper, loading
- Bypass tray.................................. 21
- Paper tray.................................... 19
Power, turn off .................................. 17
Power, turn on .................................. 16
Scan head locking switch,
releasing ........................................... 13
TD (Toner/Developer) cartridge,
Installing ........................................... 14
Tray's paper size, setting.................. 23
User program, setting ....................... 62
Basic procedure for printing .............
Button Manager, setting up
- Windows 98/Me/2000..................
- Windows XP/Vista .......................
Installing the software-Network
connection ........................................
Installing the software.......................
Online manual, using........................
Print job, canceling ...........................
Printer mode, using ..........................
Scanner mode, using .......................
Scanning from your computer ..........
Scanning using the keys on
the machine......................................
Making copies
Checking the total count and drum
cartridge life......................................
Cleaning the machine
- Cabinet ........................................
- Document glass...........................
- Drum cartridge.............................
- RSPF...........................................
- TD (Toner/Developer) cartridge .....
- Transfer charger..........................
Drum cartridge, replacing .................
Misfeeds, removing
- Fusing area .................................
- RSPF...........................................
- Paper feed area...........................
- Transport area.............................
TD (Toner/Developer) cartridge,
replacing...........................................
Copying
- Document glass...........................
- RSPF...........................................
Enlarging/reducing copies ................
Exposure, adjusting ..........................
Exposure, selecting ..........................
Setting the number of copies............
Tray, selecting ..................................
24
25
29
28
28
27
27
Using convenient copy functions
2 IN 1 copying, using
- Document glass...........................
- RSPF...........................................
Automatic two-sided copying
- Document glass...........................
- RSPF...........................................
Margin shift, using ............................
Sort copying, using
- Document glass...........................
- RSPF...........................................
35
37
31
32
38
58
55
53
47
42
61
58
58
59
60
59
Troubleshooting and maintenance
86
87
87
88
87
88
89
84
79
81
79
80
82
33
34
109
!AL-2050CS.book
MEMO
62 ページ
2008年1月7日 月曜日 午後8時10分
!AL-2050CS.book
MEMO
63 ページ
2008年1月7日 月曜日 午後8時10分
!AL-2050CS.book
MEMO
64 ページ
2008年1月7日 月曜日 午後8時10分
!AL-2050CS.book
63 ページ
2008年1月7日 月曜日 午後8時10分
♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠
For users in the USA
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this
equipment not expressly approved by the manufacturer could void the user’s
authority to operate this equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠
♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠
♠
♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠♠ ♠
Notice for Users in U.S.A.
Declaration of Conformity
SHARP Digital Multifunctional System, AL-2050CS
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Responsible Party: SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495
TEL:
1-800-BE-SHARP
This product utilizes tin-lead solder, and fluorescent lamp containing a small
amount of mercury. Disposal of these materials may be regulated due to
environmental consideration. For disposal or recycling information, please
contact your local authorities, the Electronics Industries Alliance:
www.eiae.org, the lamp recycling organization: www.lamprecycle.org or Sharp
at 1-800-BE-SHARP.
(For U.S.A. Only)
!000-Cover4.fm
1 ページ
2008年5月27日 火曜日 午後5時37分
SHARP ELECTRONICS CORPORATION
1 Sharp Plaza, Mahwah, New Jersey 07495-1163.
www.sharpusa.com
This manual has been printed using a vegetable-based
soy oil ink to help protect the environment.
Printed on 100% post-consumer recycled paper
PRINTED IN CHINA
2008E
KS3
TINSE1865QSZZ