Samsung GN642HFGD User manual

GB
Installation and
User Manual
GN642HFGD
GN642FFGD
Built-In Hotplate
P/N : 50551-40110
GB
Preface
Thank you for using our appliance.
To use this appliance correctly and prevent any potential risk, read these instructions before
use the appliance.
Keep these instructions at the place where you can find it easily.
If you are unsure of any of the information contained in these instructions, please contact the
Samsung customer care center.
Contents
Preface.......................................................2
Safety Warning ......................................4-10
- Safety Warning ..........................................4
These instructions are only valid for the countries of destination, the identification symbols
which are indicated on the cover of the instruction manual.
The manufacturer shall not be responsible for any damages to persons or property caused by
incorrect installation or use of the appliance.
- Installation .................................................5
The appliance has been certified for use in countries other than those marked on the
appliance.
The manufacturer also reserves the right to make any modifications to the products as may
be considered necessary or useful, also in the interests of the user, without jeopardizing the
main functional and safety feafures of the products themselves.
- Cleaning & Service ..................................10
- Child and People Safety ............................6
- During Use ................................................7
- Glass Top Plate .........................................9
- Environmental Information ......................10
Instructions for Use and Maintenance .11-19
- Description of the Appliance ....................11
- How to Use ..............................................12
- Safety and Energy Saving Advice ...........14
- Cleaning and Maintenance .....................16
- Troubleshooting .......................................18
- Application for Service .............................19
Technical Instructions ..........................20-27
- Technical Instructions ..............................20
- Technical Data for Engineers ..................21
- Positioning ...............................................22
- Installing the Appliance ...........................23
- Gas Connection ......................................24
- Electrical Connection ..............................25
- Gas Conversion ......................................26
- Burner Features ......................................27
3
Installation
Safety Warning
■ Your safety is the most important to Samsung.
■ You must read warnings carefully before installing or using the appliance.
■ This instruction booklet must be kept with the appliance for any future reference.
If the appliance is sold or transferred to another person, ensure the booklet is passed on to
the new user.
■ The manufacturer declines any liability should these safety measures not be observed.
■ The following marks are made to be easily understood so that you can prevent any safety
accident caused by misuse in advance and use the appliance more conveniently.
■ Completely understand the following contents before read the instruction.
Danger/Warning
If this mark is neglected, the user may be dead or seriously
injured.
Caution
If this mark is neglected, the user may be injured or damaged
in property.
Warning
■ Prior to installation, ensure that the gas
and electrical supply complies with the
type stated on the rating plate.
■ This appliance shall be installed in
accordance with regulations in force and
only used in a well ventilated space.
G30,G31 G20
■ Do not install this appliance on any
type of marine vessel or Leisure
Accommodation Vehicle.
220V
110V
■ The gas pipe and electrical cable must
be installed in such a way that they do
not touch any parts or the appliance.
■ The following marks mean as follow:
General Danger, Warning and Caution
No Access
No Fire Tool
Must Do
Caution
Danger
■ If gas seems to leak, take the actions as follow :
- Do not turn on the light.
- Do not switch on/off any electrical appliance and do not touch any electric plug.
- Do not use a telephone.
1 Stop using the product and close the middle valve.
2 Open the window to ventilate.
3 Contact our service center by using a phone outside.
* The fuel gas contains mercaptan, so that you can feel that the gas leaks even where only
1/1000 of the gas exists in the air with specific smell (smell of rotten garlic or egg).
4
■ This appliance should be installed by a qualified technician or installer.
■ The adjustment conditions for this appliance are stated on the label or data plate.
■ After unpacking the appliance, make sure the product is not damaged and that the
connection cord is in perfect condition. Otherwise, contact the dealer before installing
the appliance.
■ The adjacent furniture and all materials used in the installation must be able to
withstand a minimum temperature of 85˚C above the ambient temperature of the room
it is located in, whilst in use.
■ Remove all packaging before using the appliance.
■ In the event of burner flames being accidentally extinguished, turn off the burner
control and do not attempt to re-ignite the burner for at least one minute.
■ The use of a gas cooking appliance results in the production of heat and moisture in the room
in which it is installed. Ensure that the kitchen is well ventilated: keep natural ventilation holes
open or install a mechanical ventilation device (mechanical extractor hood).
■ Prolonged intensive use of the appliance may call for additional ventilation, for example
opening of a window, or more effective ventilation, for example increasing the level of
mechanical ventilation where present.
■ Precisely observe the evacuation of combustion products.
5
Child and People Safety
Warning
During Use
Warning
■ Do not allow children to play near or with the appliance.
■ The appliance gets hot when it is in use.
Children should be kept away until it has cooled.
Caution
■ Only use the appliance for preparing
food. Never use it as a heater.
■ It is dangerous to modify or try to
modify the characteristics of this
appliance.
■ The use of a gas cooking appliance results
in the production of heat and moisture in the
room in which it is installed. Ensure that the
kitchen is well ventilated : keep natural
ventilation holes open or install a mechanical
ventilation device (mechanical extractor
hood).
■ Do not use this appliance if it is in
contact with water. Do not operate this
appliance with wet hands.
■ The heating and cooking surfaces of
the appliance become hot when they
are in use, take all due precautions.
■ Do not use large cloths, tea towels or
similar as the ends could touch the
flames and catch fire.
■ Never leave the appliance unattended
when cooking with oil or fats. If fat or oil
overheats, then it can ignite extremely
quickly.
■ Unstable or misshapen pans should not
be used on the hob as unstable pans
can cause an accident by tipping or
spillage.
■ This appliance is designed to be operated by adults.
■ Children can also injure themselves by pulling pans or pots off the appliance.
■ This appliance is not intended for use by children or other persons whose physical,
sensory or mental capabilities or lack of experience and knowledge prevents them
from using the appliance safety without supervision or instruction by a responsible
person to ensure that they can use the appliance safety.
6
7
During Use (Continued)
■ Do not place any flammable object
near the appliance.
■ Perishable food, plastic items and
aerosols may be affected by heat and
should not stored above or below the
appliance.
■ Do not spray aerosols in the vicinity of
this appliance while it is in operaiton.
■ Ensure the control knobs are in the
‘OFF’ position when not in use.
Glass Top Plate
Warning
■ Avoid scratching the glass top plate. The glass
surface can be scratched with items such as sharp
instruments,rings or other jewelry and rivets on
clothing.
■ Large scratches or impacts to glass top plate can
lead to be broken or shattered glass.
■ Do not operate the top plate if the glass is broken.
Spillovers or cleaning solution may penetrated a
broken top plate and create a risk of electrical shock.
Immediately contact a qualified technician if you find that the glass top plate become
broken.
■ Never use the glass top plate as a cutting board.
■ Do not place or store items that can melt or catch fire on the glass top plate, even
though it is not being used.
Caution
■ This appliance is intended for domestic cooking only. It is not designed for commercial or
industrial purposes.
■ Prolonged intensive use of the appliance may call for additional ventilation, for example
opening of a window, or increasing the level of mechanical ventilation where present.
■ Use heat-resistant pot holders or gloves when handing hot pots and pans.
■ Take care not to let pot holders or gloves get damp or wet, as this causes heat to transfer
through the material quicker with the risk of burning yourself.
■ Only ever use the burners after placing pots and pans on them. Do not heat up any empty
pots or pans.
■ Never use plastic or aluminium foil dishes on the appliance.
■ When using other electrical appliances, ensure the cable does not come into contact with
the appliance surfaces of the cooking appliance.
■ If you have any mechanical substance such as artificial heart and etc in your body, consult
with a doctor before using the appliance.
■ Do not let pot holders come near open flames when lifting cookware.
■ Do not use a towel or other bulky cloth in place of a pot holder. Such cloths can catch fire
on a hot burner.
■ When using glass cookware, make sure it is designed for top plate cooking.
■ To minimize the possibility of burns, ignition of flammable materials and spillage, turn
cookware handles toward the side or center of the top plate without extending over
adjacent burners.
■ Always turn burner controls off before removing cookware.
■ Carefully watch foods being fried at a high flame setting.
■ Always heat fat slowly and watch as it heats.
■ Foods for frying should be as dry as possible.Frost on frozen foods or moisture on fresh
foods can cause hot fat to bubble up and over the sides of the pan.
■ Never try to move a pan of hot fat, especially a deep fat fryer. Wait until the fat is cool.
8
■ When cooking is finished, the glass top plate remains a little hot for a certain period of
time. Take care not to place your hands on it. Keep children at a safe distance.
■ If the glass surface get broken, unplug the appliance and contact an authorized
Samsung customer care center.
■ Do not spill water on the glass top plate.
■ Do not use pans that is much bigger than burner that we recommend. Only use
proper pan size.
■ Do not use heat - resistant chinaware and charcoal pans.
9
Cleaning & Service
Description of the Appliance
5
Warning
4
11
■ Never use abrasive or caustic
cleaning things.
■ This appliance should only be
repaired or serviced by an authorised
Service Engineer and only genuine
approved spare parts should
be used.
2
1
6-1
Caution
■ Before attempting to clean the appliance, it should be disconnected from the mains
and cool.
■ You should not use a steam jet or any other high pressure cleaning equipment to
clean the appliance.
Environmental Information
7
9
1. Glass Top Plate
2. Auxiliary Burner
3. Semi-rapid Burner
4. Rapid Burner
5. Triple crown Burner
6. Control handle for rear left burner
(Rapid burner)
6-1. Control handle for rear left burner
(Triple-crown burner)
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
■ This marking shown on the product or its literature, indicates that it should not be
disposed with other household wastes at the end of its working life. To prevent
possible harm to the environment or human health from uncontrolled waste disposal,
please separate this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.
■ Household users should contact either the retailer where they purchased this product,
or their local government office, for details of where and how they can take this item
for environmentally safe recycling.
■ Business users should contact their supplier and check the terms and conditions of
the purchase contract. This product should not be mixed with other commercial
wastes for disposal.
10
7. Control handle for front left burner
(Auxiliary burner)
8. Control handle for front right burner
(Semi-rapid burner)
9. Control handle for rear right burner
(Semi-rapid burner)
10. Pan support
11. Wok pan support
Burner
Triple crown
Auxiliary, Semi-rapid and Rapid
12-1
■ After installation, please dispose of the packaging
with due regard to safety and the environment.
■ When disposing of an old appliance, make it
unusable, by cutting off the cable.
10
6
3
8
12
12. Burner lid
12-1. Inner Burner lid
12-2. Outer Burner lid
13. Flame Spreader
14. Burner Cup
15. Ignition Electrode
16. Flame supervision device
12-2
13
14
15
16
Wok pan support
17
18
Handle
17. Wok pan
support
18. Pan support
19
20
21
11
19. Control handle
20. Sealing ring
21. Tap
How to Use
How to Use (Continued)
Turn on
1
Turn off
Preparation
The following symbols will appear on the control panel, next to each control handle :
Circle : gas off
Small flame : minimum setting
Large flame : maximum setting
Ignition position
■ The minimum setting is at the end of the anti-clockwise rotation of the control handle.
■ All operation positions must be selected between the maximum and minimum position.
■ The symbol on the control panel, next to the control handle will indicate which burner it operates.
2
3
Extinguishment
■ Turn the control handle to clockwise, to setting ‘O’ (off position)
■ Close the middle valve.
Ignition & Adjustment
■ Right after extinguishment, the appliance is still hot. Be careful not to be
burned.
■ Open the middle valve.
■ Place a pot or a pan on the corresponding cooking position.
■ Fully press down the control handle for the corresponding cooking position and turn it to the
left, to the ignition position, and hold it there for a few seconds at most until the burner ignites.
■ After igniting, keep the control handle pressed for about 5~8seconds more because the heat
sensor that opens the gas channel has to warm up first. And set control handle to the position you
want.
■ If the burner does not light, repeat the process.
■ The flame size can be set continuously between maximum and minimum by slowing turning the
control handle.
■ This appliance is fitted with a Flame supervision device which cuts off
the supply of gas to a burner if the flame goes out, for example if food
has boiled over, or if there was a sudden draught.
■ In the event of the burner flames being accidentally extinguished, turn
off the burner control and do not attemp to re-ignite the burner for at
least 1min.
■ If the igniters are dirty, this makes the burner harder to light, so you
should keep them as clean as possible. Do this with a small brush and
make sure that the ignition device is not hit or knocked violently.
■ The flame supervision device shall not be operated for more than 15s. If
after 15s the burner has not lit, stop operating the device and open the
compartment door and/or wait at least 1min before attempting a further
ignition of the burner.
12
13
Safety and Energy Saving Advice
Safety and Energy Saving Advice (Continued)
- The diameter of the bottom of the pan should correspond to that of the burner.
BURNERS
Triple crown
Rapid
Semi-Rapid
Auxiliary
PANS
Φ min.
200mm
200mm
130mm
100mm
■ User can’t use cooking pan
on the hotplate that overlap
its edge.
Φ max.
260mm
260mm
180mm
120mm
NO
This “WOK PAN SUPPORT” allows you to use
receptacles with a concave base.
YES
Do not use small diameter cookware on
large burners.
The flame should never come up the
sides of the cookware.
Always use cookware that are
suitable for each burner, so as
to avoid wasting gas and
discolouring the cookware.
Never cook without a lid or with the lid
half off
- you are wasting energy.
Always place the lid on the
cookware.
Do not use a pan with a convex or
concave bottom.
Only use pots, saucepans and
frying pans with thick, flat
bottom.
Do not place cookware on one side of a
burner, as if could tip over. Do not use
cookware with a large diameter on the
burners near the controls, which when
placed on the middle of the burner may
touch the controls or be so close to them
that they increase the temperature in this
area and may cause damage.
Always place the cookware
right over the burners, not to
one side.
Never place cookware directly on top of
the burner.
Place the cookware on top of
the pan support.
Do not use excessive weight and do not
hit the hob with heavy objects.
Handle cookware carefully
when they are on the burner.
■ “WOK PAN SUPPORT” is only for triple crown burner.
■ The manufacture declines all responsibility
CONCAVE PAN
if this additional wok pan support is not
Φ min.
Φ max.
used or are used incorrectly.
180mm
220mm
■ It is not permitted to use roasting pans, frying pans or grill stones heated
simultaneously by several burners because the resulting heat build-up
may damage the appliance.
■ Do not touch the hob top and pan support while using or for a certain
period after using.
■ As soon as a liquid starts boiling, turn down the flame so that it will
barely keep the liquid simmering.
14
15
Cleaning and Maintenance
Cleaning and Maintenance (Continued)
■ Cleaning operations must only be carried out when the appliance is cool.
■ The appliance should be disconnected from your mains supply before
commencing any cleaning process.
■ Clean the appliance regularly, preferably after each use.
■ Abrasive cleaners or sharp objects will damage the appliance
surface;you should clean it using water and a little washing up liquid.
Usable
Soft Clothing
Nylon Brush
Soft Clothing
Soft Clothing
Soft Clothing
Nylon Brush
Nylon Brush
Sponge Brush
Sponge Brush
Sponge Brush
Sponge Brush
Edible Oil
Edible Oil
Edible Oil
Unusable
Metal
Brush
Soft
Clothing
Soft Clothing
Metal Brush
Metal
Brush
Soft Clothing
Sponge
Brush
Acidic/Alkali
Sponge
Brush
Detergent
Acidic/Alkali
Sponge
Brush
Acidic/Alkali
Detergent
Detergent
Neutral Detergent
neutral Detergent
Abrasive
neutral Detergent
neutral Detergent
Abrasive
Abrasive
Thinner/Benzene
neutral
Detergent
neutral Detergent
Thinner/Benzene
Thinner/Benzene
neutral
Detergent
Nylon Brush
Nylon Brush
Nylon Brush
Metal
Brush
Nylon
Brush
Metal Brush
Metal Brush
Edible Oil
Edible Oil
Edible Oil
Edible Oil
Abrasive
Abrasive
Abrasive
Acidic/Alkali
Detergent
Acidic/Alkali
Detergent
Acidic/Alkali
Detergent
Abrasive
Metal Brush
Acidic/Alkali
Detergent
Thinner/Benzene
Thinner/Benzene
Thinner/Benzene
Thinner/Benzene
Pan support, Control handles
■ Take off the pan supports.
■ Clean these and the control handles with a damp cloth, washing up liquid and warm
water. Stubborn soiling is best soaked before.
■ Finally dry everything with a clean soft cloth.
Glass top plate
■ The glass top plate should only be cleaned when it has cooled down. Use a liquid
detergent to wash the glass, or alternatively use soapy water. For more stubborn dirt,
use the scraper supplied with the cooker.
BURNERS
■ Remove the burner lids and Flame Spreaders by pulling them upwards and away
from the top plate.
■ Soak them in hot water and a little detergent.
■ After cleaning and washing them, wipe and dry them carefully. Make sure that the
flame holes are clean and completely dry.
■ Wipe the fixed parts of the burner cup with a damp cloth and dry afterwards.
■ Gently wipe the Ignition device and flame supervision device with a well wrung-out
cloth and wipe dry with a clean cloth.
■ Before placing the burners back on the top plate, make sure that the injector is not
blocked.
■ Re-assemble the Auxiliary, Semi-Rapid and Rapid burners
as follows :
12-1
12
12-2
13
14
1. Place the flame spreader (13) on to the burner cup (14) so that the ignition device and the flame
supervision device extend through their respective holes in the flame spreader. The flame spreader
must click into place correctly.
2. Replace the burner lid (12) ensuring that the locating tabs fit into the noches in the flame spreader
(13).
■ Dry the glass plate thoroughly after cleaning.
Replace parts in the correct order after cleaning.
- Do not mix up the top and bottom.
- The locating lugs must fit exactly into the notches.
16
17
Troubleshooting
Application for Service
■ Repairs to the gas and electrical components of this appliance must only be carried out by
a suitably qualified and competent person to ensure safety.
■ However, some minor problems can be resolved as follows :
Problem
Not ignited
Badly ignited
Probable cause
No Spark.
Check the electricity supply
The burner lid is badly assembled.
Assemble the lid correctly.
The middle valve is closed.
Open the middle valve
completely.
The middle valve is incompletely
opened.
Open the middle valve
completely.
The burner lid is badly assembled.
Assemble the lid correctly.
The ignition plug is contaminated
with alien substance.
Wipe such alien substance with
dried clothing.
The burners are wet.
Dry the burners lids carefully.
The holes in the flame spreader
are clogged.
Clean the flame spreader.
The burner lid is badly assembled.
Fire off while using
The flame supervision device is
contaminated with alien substance.
Clean the flame supervision
device.
Yellow Flame
The holes in the flame spreader
are clogged.
Clean the flame spreader.
Different gas is used.
Check the gas used.
The burner lid is badly assembled.
Assemble the burner lid
correctly.
Gas Smell
Check to see if any gas taps are
on.
There may be a leak between
the coupling and the gas bottle.
Make sure that the connection is
airtight.
■ If problem is not solved, please contact the Samsung customer care
center.
Country
Customer Care
Center (TEL)
BELGIUM
02 201 2418
CZECH
REPUBLIC
844 000 844
DENMARK
70 70 19 70
FINLAND
030-6227 515
FRANCE
GERMANY
Web Site
www.
samsung.be
www.
samsung.com/cz
www.
samsung.com/dk
www.
samsung.com/fi
3260 SAMSUNG or
www.
08 25 08 65 65
samsung.com/fr
(€ 0,15/Min)
01805 - 121213
(€ 0,14/Min)
www.
samsung.de
06-80-SAMSUNG
www.
(7267864)
samsung.com/hu
800-SAMSUNG
www.
ITALIA
(7267864)
samsung.com/it
www.
LUXEMBURG 02 261 03 710
samsung.lu
www.
Europe NETHERLANDS 0900 20 200 88
(€ 0,10/Min)
samsung.nl
www.
NORWAY
815-56 480
samsung.com/no
www.
POLAND
0 801 801 881
samsung.com/pl
www.
PORTUGAL
80 8 200 128
samsung.com/pt
0800-SAMSUNG
www.
SLOVAKIA
(7267864)
samsung.com/sk
HUNGARY
SPAIN
Assemble the burner lid
correctly.
A gas tap has been left on.
18
Region
Solution
Noise made when
combusted and ignited
Unstable Flame
If you have any comments or questions regarding a Samsung products,
contact the SAMSUNG customer care center.
902 10 11 30
www.
samsung.com/es
FAX no.
Address
N/A
Samsung Electronics Benelux B.V.
Medialaan 50, 1800 Vilvoorde, Belgium
Distributor pro Českou republiku: Samsung Zrt., česka
organizační složka Vyskočilova 4, 14000 Praha 4
Samsung Electronics Nordic AB
SE -19427 Kanalvägen 10A, Upplands Väsby, Sweden
Samsung Electronics Nordic AB
SE -19427 Kanalvägen 10A, Upplands Väsby, Sweden
Samsung Service Consommateurs
66 rue des Vanesses BP 50116 - Villepinte -95950
ROISSY cedex, France
Samsung Electronics GmbH
Samsung House, Am Kronberger Hang 6, 65824
Schwalbach/Ts., Deutschland
Samsung Electronics Magyar Rt.
Szépvölgyi Business Park, 1037 Budapest, Szépvölgyi út 35-37
Samsung Electronics Italia S.p.A
Via C. Donat Cattin, 5, 20063, Cernusco Sul Naviglio (MI)
Samsung Electronics Benelux B.V.
Medialaan 50, 1800 Vilvoorde, Belgium
Samsung Electronics Benelux B.V.
Postbus 681 2600AR Delft Nederland
Samsung Electronics Nordic AB
SE -19427 Kanalvägen 10A, Upplands Väsby, Sweden
Samsung Electronics Polska sp. Z o.o.
Dział Obsługi Klienta02-678 Warszawa; ul. Szturmowa 2a
SAMSUNG ELECTRÓNICA PORTUGUESA, S.A
Rua Cesario Verde, no 5-4, Piso2795-753 Queijas-Portugal
N/A
N/A
N/A
N/A
01 48
63 06 38
01805 121214
N/A
02
92141801
N/A
N/A
N/A
+48-22607 4448
N/A
N/A
N/A
www.
0771-400 200
N/A
samsung.com/se
0870
SAMSUNG
www.
0870
U.K
(7267864)
samsung.com/uk
7221127
Republic of
www.
+44 (0)870
0818 717 100
Ireland
samsung.com/uk
7221127
http://www.
Switzerland 0800-SAMSUNG
N/A
(7267864)
samsung.com/ch/
www.
+7-495RUSSIA
8-800-200-0400
samsung.ru
783-0556
www.
+7 (3272)
KAZAHSTAN 8-800-080-1188
samsung.kz
58-59-66
www.
+998-71UZBEKISTAN 8-800-120-0400
samsung.uz
120-7208
www.
+380 (44)
UKRAINE
8-800-502-0000 samsung.com/ur
537 59 48
www.
+370 52
LITHUANIA
8-800-77777
samsung.lt
139 770
http://www.samsung.
+371 7
LATVIA
800-7267
com/lv/index.htm
50 84 80
www.
ESTONIA
800-7267
samsung.ee
www.
(612)
AUSTRALIA
1300 362 603
samsung.com/au 9763 5750
SWEDEN
CIS
MALAYSIA
1800-88-9999
www.
samsung.com/my
0322636759
THAILAND
1800-29-3232
02-689-3232
www.
samsung.com/th
02689-3298
Asia
Pacific
19
SAMSUNG ELECTRÓNICS IBÉRIA, S.A
Ciencies, 55-65 (Polígono Pedrosa)
08908 HOSPITALET DE LLOBREGAT (Barcelona)
Samsung Electronics Nordic AB
SE -19427 Kanalvägen 10A, Upplands Väsby, Sweden
Samsung Electronics U.K. Ltd. Customer Care Centre PO
Box 17243 Edinburgh, EH11 4YB United Kingdom
117545 Россия, Москва, ул. Дорожная, д.3, корп. 6
050051 4th floor, 172 Dostyk Ave. Almaty Republic of
Kazakhstan
100-742 12fl.,International Business Center,107B,Amir
Temur str., Tashkent,Uzbekistan
30A, Spaska St, Floor 3, Kiev 04070, Ukraine
Zemaites 21, Vilnius, LT-2009, Lithuania
J. Alunana 2, Riga, LV-1340, Latvia
Samsung Electronics Australia
7 Parkview Drive, Homebush Bay NSW 2127
Samsung Malaysia Electronics Sdn. Bhd.
3B-1-1. Level 1, Block 3B, Plaza Sentral, Jalan Stesen
Sentral 5, KL Sentral , 50470, Kuala Lumpur, Malaysia
Thai Samsung Electronics Co.,Ltd Service Department
1,6 floor Boonmitr Building 138 Silom Rd., Suriyawong
Bangrak Bangkok 10500
บริษัท ไทยซัมซุงอิเล็คโทรนิคส์ จำกัด
เลขที่ 138 อาคารบุญมิตร ชั้น 1,6 ถนนสีลม
แขวงสุริยวงศ์ เขตบางรัก กรุงเทพฯ 10500
Remark
Technical Instructions
■ This appliance must be installed by a qualified technician or installer.
Technical Data for Engineers
Appliance Specification
■ Prior to installation, ensure that the local distribution conditions
(nature of the gas and gas pressure) and the adjustment of the
appliance are compatible.
D
■ The adjustment conditions for this appliance are stated on the label
(or data plate).
■ This appliance is not connected to a combustion products evacuation
device. It shall be installed and connected in accordance with current
installation regulations. Particular attention shall be given to the
relevant requirements regarding ventilaton.
H
Model
Pan Support
■ All appliances containing any electrical components must be earthed.
Support Wok
■ Gas pipe or connector shouldn’t be bent or blocked by any other
appliances.
■ Check the dimensions of the appliance as well as the dimensions of
the gap to be cut in the kitchen unit.
■ The panels located above the work surface, directly next to the
appliance, must be made of non-flammable material. Both the stratified surfacing and the glue used to secure it should be heat resistant,
to prevent deterioration.
■ Turn on appliance tap and light each burners.
Check for a clear blue flame without yellow tipping.
If burners shows any abnormalties check the following :
- Burner lid on correctly
- Flame spreader positioned correctly
- Burner vertically aligned with injector nipple
■ A full operational test and a test for possible leakages must be carried
out by the fitter after installaion.
■ The flexible tube shall be fitted in such a way that it cannot come into
contact with a moveable part of the housing unit and does not pass
through any space susceptible of becoming congested.
W
GN642HFGD
GN642FFGD
Cast Iron
O
X
Top Plate
Tempered glass (8t)
Control Handle
Titan color
Weight (net)
13.5kg
13.0kg
Weight (gross)
16.2kg
15.7kg
Dimension (WxDxH)
594x510x46
594x510x46
Ignition device
Continuous Ignition Type
Gas Connection
1/2 inch female thread
Electric supply
220V~240V, 50/60Hz
Burner Feature
Triple crown(1EA),
Semi-rapid(2EA), Auxiliary(1EA)
Rapid(1EA), Semi-rapid(2EA),
Auxiliary(1EA)
○ APPLIANCE CLASS : Class 3
○ APPLIANCE CATEGORY :
BE/FR
GB/IT/PT/LT/ES/CZ/SK
PL
Cat.
II 2E+3+
II 2H3+
II 2E3B/P
P(mbar)
20/25 - 28-30/37
20 - 28-30/37
20-36
HU
20
H
W
■ Before installing, turn off the gas and electricity supply to the
appliance.
■ Ensure that the gas pipe and electrical cable are installed in such a
way that they do not touch any parts of the appliacne which become
hot.
D
Cat.
II 2H3B/P
P(mbar)
25-30
21
Installing the Appliance
Positioning
CLEARANCES REQUIRED
WHEN FITTING THE HOB
WITHOUT A COOKER HOOD ABOVE
1. Remove the pan support, the burner lid and
flame spreader and carefully turn the
appliance upside down and place it on a
cushioned mat.
Take care that the Ignition devices and flame
supervision devices are not damaged in this
operation.
2. Apply the sealing strip provided around the
edge of the appliance.
3. Do not leave a gap in the sealing agent or
overlap the thickness.
CLEARANCES REQUIRED
WHEN FITTING THE HOB
WITH A COOKER HOOD ABOVE
600 mm
700 mm
700 mm
400 mm
55
55
m
m
m
m
400 mm
m
560
mm
m
m
400 mm
100 m
48
0
m
0
mm
48
560
m
400 mm
100 m
m
Cut out size
Width : 560mm
Depth : 480mm
Thickness : 30~50mm
Do not use a silicon sealant to seal the
appliance against the aperture.
This will make it difficult to remove the
appliance from the aperture in future,
particularly if it needs to be serviced.
FO 0813
FO 0812
■ This appliance is to be built into a kitchen unit or 600mm worktop, providing the
following minimum distances are allowed ;
- The edge of the appliance must be a minimum distance of 55mm from a rear wall.
- A minimum distance of 100mm must be left between the side edges of the appliance and any
adjacent cabinets or walls.
- The minimum distance combustible material can be fitted above the appliance in line with the
edges of the appliance is 400mm. If it is fitted below 400mm a space of 50mm must be allowed
from the edges of the appliance.
- The minimum distance combustible material can be fitted directly above the appliance is 700mm.
40mm
a
1. Place the bracket(B) over the holes that match the size
of the screws.There are one set of screw holes in each
corner of the hob(H).
Slightly tighten a screw(C) through the bracket(B) so
that the bracket is attached to the hob, but so that you
can still adjust the position it.
2. Carefully turn the hob back over and then gently lower it
into the aperture hole that you have cut out.
3. On the underneath of the hob, adjust the brackets into a
position that is suitable for your worktop.
Then fully tighten the screws(C) to secure the hob into
position.
(A) SEALING STRIP
(C) SCREW
(B) BRACKET
150mm (MAX)
- This panel(a) must be positioned at a maximum distance of 150mm below the worktop.
H
H
H
H
22
23
Gas Connection
■ This appliance must be installed and connected in accordance with installation regulations in force in the country in which the appliance is to be used.
■ This appliance is supplied to run on natural gas only and cannot be used on
any other type of gas without modification. Conversion for use on LPG and
other gases must only be undertaken by a qualified person.
Electrical Connection
■ This appliance must be earthed.
■ This appliance is designed to be connected to a 220~240V, 50/60Hz AC electricity supply.
■ The wires in the mains lead are coloured in accordance with the following code ;
- Green/yellow = Earth
- Blue
= Neutral
- Brown
= Live
The gas inlet connection fitting is 1/2 inch female thread.
Gas distributed by pipe ; natural gas, propane-air gas or butane-air gas
For your safety, you must choose from the three following connection option.
■ The wire which is coloured green and yellow must be connected
to the terminal which is marked with the letter E or by the earth
symbol.
■ Connection with a rigid pipe made from copper and with
screw-on mechanical connectors.
Make the connection directly to the end of the elbow fitted on
the appliance.
■ Connection using flexible undulated metal tube with
screw-on connectors. (Fig. A)
You can use a flexible stainless steel pipe available from your
after sales service department.
Elbow
Fig.A
■ Connection using flexible tube with screw-on connectors.
(Fig.B)
These tubes must not exceed 2 meters in length and must be
accessible along their entire length.
Fig.B
■ WIRING DIAGRAM
N
Elbow
■ For an existing installation, where it is not possible to fit a
reinforced, braided, flexible gas hose, the connection can be
made with a flexible gas hose (maximum length 2meters),
Connector
with two clamps.
One on the connector, and the other on the pressure
Clamp
regulator, and a gasket should be fitted between the
connector and the hob’s elbow. (Fig.B)
Gasket
Fig.A
Fig.B
N
CONNECTOR
GREEN & YELLOW TO EARTH
Gas supplied by tank or cylinder (butane/propane)
■ For the user’s safety, we advise the connection to be made
with a rigid pipe if this is possible, using a flexible undulated
metal tube with scerw-on connectors (maximum length
2meters) (Fig.A)
BLUE TO NEUTRAL
GND
L
Ignition
L
Electrode
2
3
4
�
�
L
BROWN TO LIVE
 MICRO SWITCHES
 IGNITER
(INPUT: 220V 50~60HZ, OUTPUT: 15.25V)
■ You can obtain the connector and the gasket from your After-Sales Service.
In France, you must use a tube or a pipe featuring the “NF Gaz” logo.
If the installation is difficult, unscrew the Elbow slightly and tighten it after
locating the Elbow.
■ A full operational test and a test for possible leakages must be carried out
by the fitter after installation.
■ Access to the whole length of the connection hose must be possible and
the gas hose must be replaced before its use before the end of service life
(indicated on the hose)
24
N 1
25
Gas Conversion
1
2
Burner Features
■ Be careful, the operations and adjustments to be carried out when converting
from one gas to another.
■ All work must be carried out by a qualified technician.
■ Before you begin, turn off the gas and electricity supply to the appliance.
Change the injector of the burners.
Remove the pan support, Burner lid and Flame spreader.
Injector
Unscrew the injector using a 7mm box spanner and replace it with
the stipulated injector for new gas supply. ( see table 1. Page 27.)
Carefully reassemble the all components.
After injectors are replaced, it is advisable to strongly tighten the
injector in place.
Adjusting of the taps of the cooking hob burners for
reduced consumption
➀ Turn the taps down to minimum.
Control handle
Tap
Sealing ring
Tap
by-pass screw
➁ Remove the control handles from taps.
➂ Adjusting the by-pass screw.
- For converting G20 into G30 or G31, the screw must
be screwed down fully tight.
- At this stage, light up the burners and turn the
control handles from max position to minimum
position to check flame stability.
- For converting G30 or G31 into G20, please contact
“After-Sales Service”.
➃ Replace the control handles on the taps.
■ Do not dismantle the tap shaft : in the event of a malfunction, change the whole tap.
■ Before placing the burners back on the top place, make sure that the injector is
not blocked.
■ A full operational test and a test for possible leakages must be carried out after
gas conversion. (such as soap water or gas detector)
■ After completing conversion, a qualified technician or installer has to mark “V”
on the right gas category
to match with the setting
0063
in rating plate.
GN642HFGD
S/N: A36579MZ400007A
Remove the previous
G20/20mbar
220-240V 50/60Hz, Pmax 1W
setting “V” mark.
∑Qn Q20: 7.5kW G30: 521g/h G31: 503g/h
G20-20mbar
26
G30/29mbar
G31/37mbar
GB Cat.: ll 2H3+
(Table 1)
Nominal heat input and flow rates see below at 15˚C at 1,013 mbar.
COUN- TYPE OF
TRY
GAS
BURNER
POSITION
Triple-Crown
Max
Min
GB,IT
Injector make
88
(1/100 mm)
FR,HU
G-30
BE,LT
heat input 3.0 1.25
BUTANE Nominal
(Kw)
NL,PT
29 mbar
ES,CZ
Nominal flow rates 211.1 35
(g/h)
SK
Rapid
Max
PL
GB,IT
FR,BE G-31
LT,PT PROPANE
ES,CZ 37 mbar
SK
Injector make
(1/100 mm)
Nominal heat input
(Kw)
Nominal flow rates 199.4
(g/h)
Max
65
Min
50
1,75
0.43
1.0
0.37
211
53
120
31
71
25
80
62
47
0.81
1,75
0.47
1.0
0.38
203
58
125
33
71
25
50
3.0
0.71
1,75
0.41
1.0
0.33
45
199
49
118
28
68
23
Injector make
125
(1/100 mm)
G-20
heat input 3.0 1.31
NATURAL Nominal
(Kw)
25 mbar
Nominal flow rates 271 124
(L/h)
97
72
1.14
1,75
0.63
1.0
0.45
271
79
166
54
91
30
91
68
3.0
1.33
1,75
0.57
1.0
0.49
271
79
166
54
91
30
Calibrated orifice 1/100mm
Auxiliary
31
Semi-rapid
34
Rapid
43
Triple-Crown
60
27
7.5
-
Burner
- Aeration adjustment none
7.5
-
3.0
110
7.5
-
1.25
119
7.5
-
3.0
65
Total
-
0.74
85
Injector make
130
GB,IT
(1/100 mm)
FR,BE G-20
heat rating 3.0 1.25
LT,PT NATURAL Nominal
(Kw)
PL,ES 20 mbar
Nominal flow rates 271 118
CZ,SK
(L/h)
HU
Min
Auxiliary
3.0
88
3.0
Max
85
Injector make
(1/100 mm)
80
G-30
heat input 3.0 1.28
BUTANE Nominal
(Kw)
37 mbar
Nominal flow rates 203.4 35
(g/h)
Min
Semi-rapid
7.5