Makita 5603R Instruction manual

ENGLISH (Original instructions)
INSTRUCTION MANUAL
Circular Saw
5603R
5703R
5705R
5903R
5103R
5143R
005391
DOUBLE INSULATION
IMPORTANT: Read Before Using.
ENGLISH (Original instructions)
SPECIFICATIONS
Model
5603R
5703R
5705R
5903R
5103R
5143R
Blade diameter
165 mm
190 mm
190 mm
235 mm
270 mm
355 mm
at 90°
54 mm
66 mm
66 mm
85 mm
100 mm
130 mm
at 45°
38 mm
46 mm
46 mm
64 mm
73 mm
90 mm
No load speed (min-1)
5,000
4,800
4,800
4,500
3,800
2,700
Overall length
330 mm
356 mm
356 mm
400 mm
442 mm
607 mm
Net weight
4.9 kg
5.7 kg
5.7 kg
7.2 kg
9.4 kg
14.0 kg
Max. cutting
depth
Safety class
/II
/II
/II
/II
/II
/II
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
END201-5
ENG905-1
Noise
Symbols
The typical A-weighted noise level determined according
to EN60745:
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
· Read instruction manual.
·
DOUBLE INSULATION
·
Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic
equipment
and
its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible recycling
facility.
Model 5603R,5703R
Sound pressure level (LpA) : 93 dB(A)
Sound power level (LWA) : 104 dB(A)
Uncertainty (K) : 3 dB(A)
Model 5705R,5143R
Sound pressure level (LpA) : 94 dB(A)
Sound power level (LWA) : 105 dB(A)
Uncertainty (K) : 3 dB(A)
Model 5903R
Sound pressure level (LpA) : 95 dB(A)
Sound power level (LWA) : 106 dB(A)
Uncertainty (K) : 3 dB(A)
Model 5103R
ENE028-1
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece.
Sound pressure level (LpA) : 97 dB(A)
Sound power level (LWA) : 108 dB(A)
Uncertainty (K) : 3 dB(A)
ENF002-2
Wear ear protection
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
ENG900-1
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Model 5603R,5103R,5143R
Work mode : cutting wood
Vibration emission (ah,W ) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s2
2
The technical
documentation is kept by our authorised representative
in Europe who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
Model 5703R
Work mode : cutting wood
Vibration emission (ah,W ) : 3.5 m/s2
Uncertainty (K) : 1.5 m/s2
Model 5903R
30.1.2009
Work mode : cutting wood
2
Vibration emission (ah,W ) : 3.0 m/s
2
Uncertainty (K) : 1.5 m/s
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
Model 5705R
Work mode : cutting wood
2
Vibration emission (ah,W ) : 2.5 m/s
2
Uncertainty (K) : 1.5 m/s
ENG901-1
•
•
•
•
GEA005-3
The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
WARNING:
The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3.
Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
ENH101-15
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Circular Saw
Model No./ Type: 5603R, 5703R, 5705R, 5903R, 5103R,
5143R
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
3
7.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9.
If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
10. Use of power supply via a RCD with a rated
residual current of 30mA or less is always
recommended.
Personal safety
11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
13. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
16. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
17. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
Power tool use and care
18. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
19. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
20. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
21. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
22. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
23. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
24. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
Service
25. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
26. Follow instruction for
lubricating and
changing accessories.
27. Keep handles dry, clean and free from oil and
grease.
4
GEB029-4
CIRCULAR SAW SAFETY
WARNINGS
1.
9.
DANGER: Keep hands away from cutting
area and the blade. Keep your second hand on
auxiliary handle, or motor housing. If both
hands are holding the saw, they cannot be cut by
the blade.
Do not reach underneath the workpiece. The
guard cannot protect you from the blade below the
workpiece. Do not attempt to remove cut material
when blade is moving.
CAUTION: Blades coast after turn off. Wait until
blade stops before grasping cut material.
Adjust the cutting depth to the thickness of
the workpiece. Less than a full tooth of the blade
teeth should be visible below the workpiece.
Never hold piece being cut in your hands or
across your leg. Secure the workpiece to a
stable platform. It is important to support the work
properly to minimize body exposure, blade binding,
or loss of control.
2.
3.
4.
A typical illustration of proper hand support, workpiece
support, and supply cord routing (if applicable).
000157
5.
6.
7.
8.
Hold the power tool by insulated gripping
surfaces only, when performing an operation
where the cutting tool may contact hidden
wiring or its own cord. Contact with a "live" wire
will also make exposed metal parts of the power
tool "live" and could give the operator an electric
shock.
When ripping, always use a rip fence or
straight edge guide. This improves the accuracy
of cut and reduces the chance of blade binding.
Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the
saw will run eccentrically, causing loss of control.
Never use damaged or incorrect blade
washers or bolt. The blade washers and bolt
were specially designed for your saw, for optimum
5
Kickback causes and related warnings
−
kickback is a sudden reaction to a pinched,
bound or misaligned saw blade, causing an
uncontrolled saw to lift up and out of the
performance and safety of operation.
workpiece toward the operator;
–
when the blade is pinched or bound tightly by
the kerf closing down, the blade stalls and the
motor reaction drives the unit rapidly back
toward the operator;
–
if the blade becomes twisted or misaligned in
the cut, the teeth at the back edge of the
blade can dig into the top surface of the
wood causing the blade to climb out of the
kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below.
•
Maintain a firm grip with both hands on the
saw and position your arms to resist
kickback forces. Position your body to
either side of the blade, but not in line with
the blade. Kickback could cause the saw to
jump backwards, but kickback forces can be
controlled by the operator, if proper
precautions are taken.
•
When blade is binding, or when interrupting
a cut for any reason, release the trigger and
hold the saw motionless in the material
until the blade comes to a complete stop.
Never attempt to remove the saw from the
work or pull the saw backward while the
blade is in motion or kickback may occur.
Investigate and take corrective actions to
eliminate the cause of blade binding.
•
When restarting a saw in the workpiece,
centre the saw blade in the kerf and check
that saw teeth are not engaged into the
material. If saw blade is binding, it may walk
up or kickback from the workpiece as the saw
is restarted.
•
Support large panels to minimise the risk
of blade pinching and kickback. Large
panels tend to sag under their own weight.
Supports must be placed under the panel on
both sides, near the line of cut and near the
edge of the panel.
To minimize the risk of blade pinching and kickback.
When cutting operation requires the resting of the
saw on the workpiece, the saw should be rested on
the larger portion and the smaller piece cut off.
To avoid kickback, do support
board or panel near the cut.
000154
000194
•
10.
Do not support board or
panel away from the cut.
000156
•
•
•
•
Do not use dull or damaged blades.
Unsharpened or improperly set blades
produce narrow kerf causing excessive friction,
blade binding and kickback. Keep blade sharp
and clean. Gum and wood pitch hardened on
blades slows saw and increases potential for
kickback. Keep blade clean by first removing it
from tool, then cleaning it with gum and pitch
remover, hot water or kerosene. Never use
gasoline.
Blade depth and bevel adjusting locking
levers must be tight and secure before
making cut. If blade adjustment shifts while
cutting, it may cause binding and kickback.
Use extra caution when sawing into
existing walls or other blind areas. The
protruding blade may cut objects that can
cause kickback.
ALWAYS hold the tool firmly with both
hands. NEVER place your hand or fingers
behind the saw. If kickback occurs, the saw
could easily jump backwards over your hand,
leading to serious personal injury.
11.
12.
13.
6
Never force the saw. Forcing the saw can
cause uneven cuts, loss of accuracy, and
possible kickback. Push the saw forward at a
speed so that the blade cuts without slowing.
Check lower guard for proper closing before
each use. Do not operate the saw if lower
guard does not move freely and close instantly.
Never clamp or tie the lower guard into the
open position. If saw is accidentally dropped,
lower guard may be bent. Raise the lower guard
with the retracting handle and make sure it moves
freely and does not touch the blade or any other
part, in all angles and depths of cut.
To check lower guard, open lower guard by hand,
then release and watch guard closure. Also check
to see that retracting handle does not touch tool
housing. Leaving blade exposed is VERY
DANGEROUS and can lead to serious personal
injury.
Check the operation of the lower guard spring.
If the guard and the spring are not operating
properly, they must be serviced before use.
Lower guard may operate sluggishly due to
damaged parts, gummy deposits, or a build-up of
debris.
Lower guard may be retracted manually only
for special cuts such as "plunge cuts" and
"compound cuts". Raise lower guard by
retracting handle and as soon as blade enters
the material, the lower guard must be released.
For all other sawing, the lower guard should
operate automatically.
Always observe that the lower guard is
covering the blade before placing saw down on
bench or floor. An unprotected, coasting blade will
cause the saw to walk backwards, cutting whatever
is in its path. Be aware of the time it takes for the
blade to stop after switch is released. Before
setting the tool down after completing a cut, be
sure that the lower guard has closed and the blade
has come to a complete stop.
14.
15.
16.
17.
18.
19.
20.
21.
Use the appropriate saw blade for the riving
knife. For the riving knife to function, the body of
the blade must be thinner than the riving knife and
the cutting width of the blade must be wider than
the thickness of the riving knife.
Adjust the riving knife as described in this
instruction
manual.
Incorrect
spacing,
positioning and alignment can make the riving
knife ineffective in preventing kickback.
Always use the riving knife except when
plunge cutting. Riving knife must be replaced
after plunge cutting. Riving knife causes
interference during plunge cutting and can create
kickback.
For the riving knife to work, it must be engaged
in the workpiece. The riving knife is ineffective in
preventing kickback during short cuts.
Do not operate the saw if riving knife is bent.
Even a light interference can slow the closing rate
of a guard.
Use extra caution when cutting damp wood,
pressure treated lumber, or wood containing
knots. Maintain smooth advancement of tool
without decrease in blade speed to avoid
overheating the blade tips.
Avoid Cutting Nails. Inspect for and remove all
nails from lumber before cutting.
Place the wider portion of the saw base on that
part of the workpiece which is solidly
supported, not on the section that will fall off
when the cut is made. As examples, Fig. 1
illustrates the RIGHT way to cut off the end of
a board, and Fig. 2 the WRONG way. If the
workpiece is short or small, clamp it down. DO
NOT TRY TO HOLD SHORT PIECES BY HAND!
Fig. 2
000150
22.
Never attempt to saw with the circular saw
held upside down in a vise. This is extremely
dangerous and can lead to serious accidents.
000029
23.
24.
Fig. 1
25.
26.
Some material contains chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
supplier safety data.
Do not stop the blades by lateral pressure on
the saw blade.
Always use blades recommended in this
manual. Do not use any abrasive wheels.
Wear a dust mask and hearing protection
when use the tool.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
000147
7
Sighting
FUNCTIONAL DESCRIPTION
•
For 5603R, 5703R,5705R, 5903R, 5103R
CAUTION:
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on
the tool.
5603R,5703R,5705R
B
Adjusting depth of cut
1. Base plate
A
1
1. Lever
005394
5903R/5103R
B
1
1. Top guide
2. Base
A
2
1
005392
CAUTION:
After adjusting the depth of cut, always tighten the
lever securely.
Loosen the lever on the depth guide and move the base
up or down. At the desired depth of cut, secure the base
by tightening the lever.
For cleaner, safer cuts, set cut depth so that no more
than one blade tooth projects below workpiece. Using
proper cut depth helps to reduce potential for dangerous
•
005449
For straight cuts, align the A position on the front of the
base with your cutting line. For 45° bevel cuts, align the B
position with it.
For 5143R
1. 60 ゚ angle cuts
1
KICKBACKS which can cause personal injury.
2
Bevel cutting
3
4
1. Clamping screw
7
1
2. 45 ゚ angle cuts
3. 30 ゚ angle cuts
4. Straight cuts
5. Blade
6. Base
7. Top guide
5
6
005396
Align your sight line with either the 0° notch for straight
cutting or the 30° notch for 30° angle cuts or the 45° notch
for 45° angle cuts or the 60° notch for 60° angle cuts.
1
Riving knife adjustment
005393
For model 5603R, 5703R,5705R, 5903R, 5103R
Loosen the clamping screws in front and back, and tilt the
tool to the desired angle for bevel cuts (0° - 45°). Secure
the clamping screws tightly in front and back after making
the adjustment.
For model 5143R
Loosen the clamping screw in front and tilt the tool to the
desired angle for bevel cuts (0 - 60°). Secure the
clamping screw tightly in front after making the
adjustment.
1
2
3
4
1- 5mm
1- 5mm
1. Setting
protuberances
2. Hex socket head
bolt (For
adjusting riving
knife)
3. Setting
protuberances
4. Cutting depth
005397
Use the hex wrench to loosen the hex socket head bolt
for the riving knife adjustment, then raise the lower blade
guard. Move the riving knife up or down over the two
protuberances for settings indicated in the figure, so as to
obtain the proper clearance between the riving knife and
8
saw blade.
•
CAUTION:
Ensure that the riving knife is adjusted such that:
The distance between the riving knife and the
toothed rim of the saw blade is not more than 5 mm.
The toothed rim does not extend more than 5 mm
beyond the lower edge of the riving knife.
2
Switch action
005399
1
CAUTION:
Be sure the blade is installed with teeth pointing up
at the front of the tool.
•
Use only the Makita wrench to install or remove the
blade.
•
Never depress the shaft lock while the saw is
running.
To remove the blade, press the shaft lock fully so that the
blade cannot revolve and use the hex wrench to loosen
the hex bolt counterclockwise. Then remove the hex bolt,
outer flange and blade.
To install the blade, follow the removal procedure in
reverse. BE SURE TO TIGHTEN THE HEX BOLT
CLOCKWISE SECURELY.
1. Lock-off button
2. Switch trigger
•
2
005398
CAUTION:
Before plugging in the tool, always check to see
that the switch trigger actuates properly and returns
to the "OFF" position when released.
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
push in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
•
ASSEMBLY
•
1. Hex wrench
2. Shaft lock
1
1. Hex socket head
bolt
2. Outer flange
3. Saw blade
Inner flange
3
1
005400
When changing blade, make sure to also clean upper
and lower blade guards of accumulated sawdust. Such
efforts do not, however, replace the need to check lower
guard operation before each use.
Removing or installing saw blade
The following blade can be used with this tool.
Model
Max. dia.
Min. dia.
Blade thickness
Kerf
5603R
165 mm
150 mm
1.6 mm or less
1.9 mm or more
5703R,5705R
190 mm
170 mm
1.6 mm or less
1.9 mm or more
5903R
235 mm
210 mm
1.7 mm or less
2.1 mm or more
5103R
270 mm
260 mm
1.8 mm or less
2.2 mm or more
5143R
355 mm
350 mm
2.3 mm or less
2.7 mm or more
4
2
CAUTION:
Always be sure that the tool is switched off and
unplugged
4. before carrying out any work on the tool.
Connecting a vacuum cleaner
1. Vacuum cleaner
006481
The thickness of the riving knife is 1.8 mm for Models
5603R,5703R and 5705R or 2.0 mm for Models for
5903R and 5103R or 2.5 mm for Model 5143R.
•
•
CAUTION:
Do not use saw blades which do not comply with
the characteristics specified in these instructions.
Do not use saw blades the disc of which is thicker
or the set of which is smaller than the thickness of
the riving knife.
1
005414
When you wish to perform clean cutting operation,
connect a Makita vacuum cleaner to your tool. Install the
joint on the tool using the screws. Then connect a hose of
the vacuum cleaner to the joint as shown in the figure.
9
cuts of
possible.
OPERATION
uniform
width
MAINTENANCE
CAUTION:
Be sure to move the tool forward in a straight line
gently. Forcing or twisting the tool will result in
overheating the motor and dangerous kickback,
possibly causing severe injury.
Hold the tool firmly. The tool is provided with both a front
grip and rear handle. Use both to best grasp the tool. If
both hands are holding saw, they cannot be cut by the
blade. Set the base on the workpiece to be cut without the
blade making any contact. Then turn the tool on and wait
until the blade attains full speed. Now simply move the
tool forward over the workpiece surface, keeping it flat
and advancing smoothly until the sawing is completed.
To get clean cuts, keep your sawing line straight and your
speed of advance uniform. If the cut fails to properly
follow your intended cut line, do not attempt to turn or
force the tool back to the cut line. Doing so may bind the
blade and lead to dangerous kickback and possible
serious injury. Release switch, wait for blade to stop and
then withdraw tool. Realign tool on new cut line, and start
cut again. Attempt to avoid positioning which exposes
operator to chips and wood dust being ejected from saw.
Use eye protection to help avoid injury.
•
•
•
CAUTION:
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance.
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may
result.
Replacing carbon brushes
1. Limit mark
1
001145
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps.
1. Screwdriver
2. Brush holder
cap
005401
•
CAUTION:
The riving knife should always be used except
when plunging in the middle of the workpiece.
2
1
005403
Rip fence (Guide rule)
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
005402
The handy rip fence allows you to do extra-accurate
straight cuts. Simply slide the rip fence up snugly against
the side of the workpiece and secure it in position with
the screw on the front of the base. It also makes repeated
10
OPTIONAL ACCESSORIES
CAUTIO
N:
•
These accessories or attachments
are recommended for use with your
Makita tool specified in this manual.
The use of any other accessories or
attachments might present a risk of
injury
to
persons.
Only
use
accessory or attachment for its stated
purpose.
If you need any assistance for more
details regarding these accessories, ask
your local Makita Service Center.
•
Saw blades
•
Rip fence (Guide rule)
•
Hex wrench
•
Joint
NOTE:
•
Some items in the list may be
included in the tool package as
standard accessories. They may differ
from country to country.
This manual has been written and prepared by Makita Corporation.
Makita Corporation
Anjo, Aichi, Japan
884364H224
www.makita.com