Electrolux EW 1050 F Operating instructions

L AV AT R I C E
L AV E - L I N G E
W A S C H A U T O M AT
WASHING MACHINE
LIBRETTO ISTRUZIONI
NOTICE D’UTILISATION
GEBRAUCHSANWEISUNG
WAGHING MACHINE
EWS 1 0 3 0
I
F
D
135 499 200
Downloaded From WashingMachine-Manual.com Manuals
GB
Dear customer,
Transport damages
Please read these operating instructions carefully
and pay particular attention to the safety notes
indicated in the first pages. We recommend that you
keep this instruction booklet for future reference and
pass it on to any future owners.
When unpacking the appliance, check that it is not
damaged. If in doubt, do not use it and contact the
Service Centre.
The symbols you will see on some paragraphs of this booklet have the following meaning:
The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly
important for your safety or correct functioning of the appliance.
The information marked with this symbol provides additional instructions and practical tips on the use of
the appliance.
Tips and information about economical and ecological use of the machine are marked with this symbol.
ENGLISH
Our contribution to the protection of the
environment: we use environmentally
friendly paper.
Contents
Warnings
72
Disposal
73
Tips for environmental protection
73
Technical specifications
73
Installation
74
Unpacking
74
Positioning
74
Water inlet
75
Electrical connection
75
Detergent dispenser drawer
Use
Control panel
Controls
Washing hints
Sorting the laundry
Maintenance
74-75
Water drainage
Description of the appliance
Temperatures
Before loading the laundry
Maximum loads
Laundry weights
Removing stains
Detergents and additives
International wash code symbols
Operating sequence
Washing programmes
76
76
77
77
77-80
81
81
Downloaded From WashingMachine-Manual.com Manuals
88
Door seal
Bodywork
Detergent dispenser drawer
Drain pump
Water inlet filter
Emergency emptying out
Frost precautions
88
88
88
88-89
89
89
89
Something not working?
90-91
Service Centre List
71
81
81
81
81
81
82
83
84-86
87
92
Warnings
The following warnings are provided in the interests of overall safety. You must read them carefully before
installing or using the appliance.
Installation
General safety
• All internal packing must be removed before using
the appliance. Serious damage may be caused to
the machine or adjacent furniture if the protective
transit devices are not removed or are not
completely removed. Refer to the relevant
paragraph in the instruction book.
• Any electrical work required to install this appliance
must be carried out by a qualified electrician.
• Any plumbing work required to install this appliance
must be carried out by a qualified plumber.
• After having installed the machine, check that it is
not standing on its electrical supply cable.
• If the appliance is placed on a carpeted floor,
ensure that air can circulate freely between the feet
and the floor.
• Repairs to the machine must be carried out only by
qualified personnel. Repairs carried out by
inexperienced persons could cause serious
danger. Contact your local Service Centre.
• Never pull the power supply cable to remove the
plug from the socket; always take hold of the plug
itself.
• During high temperature wash programmes the
door glass may get hot. Do not touch it!
Child safety
• Children are often not aware of how dangerous
electrical appliances can be. When the machine is
working, children should be carefully supervised
and not be allowed to play with the appliance.
Use
• The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children - danger
of suffocation! Keep them out of children’s reach.
• This appliance is designed for domestic use. It
must not be used for purposes other than those for
which it was designed.
• Only wash fabrics which are designed to be
machine washed. Follow the instructions on each
garment label.
• Do not overload the appliance. Follow the
instructions in the instruction book.
• Make sure that all pockets are empty. Objects such
as coins, safety pins, pins and screws can cause
extensive damage.
• Do not machine wash garments saturated with
petroleum, methylated spirits, trichlorethylene, etc.
If such fluids have been used to remove stains
prior to washing, wait until they have completely
evaporated from the fabric before placing garments
in the appliance.
• Place small items such as socks, belts, etc. in a
cloth bag or pillowcase to prevent them getting
trapped between the drum and the tub.
• Use only the recommended quantities of fabric
softener. An excessive amount could damage the
laundry.
• Leave the porthole door slightly ajar when the
appliance is not in use. This preserves the door
seal and prevents the formation of musty smells.
• Always check that water has emptied out before
opening the door. If not, drain the water following
the instructions in the instruction book.
• Always unplug the appliance and shut the water
tap after use.
• Keep all detergents in a safe place out of children’s
reach.
• Make sure that children or pets do not climb into the
drum. To avoid this the machine incorporates a
special feature. To activate this device, rotate the
button (without pressing it) inside the door clockwise
until the groove is horizontal. If necessary use a coin.
To disable this device and restore the possibility of
closing the door, rotate the button anti-clockwise until
the groove is vertical.
P1131
• When the appliance is to be scrapped, cut off the
electrical supply cable and destroy the plug with
the remaining cable. Disable the door catch in
order to prevent children from becoming trapped
inside while playing.
72
Downloaded From WashingMachine-Manual.com Manuals
Disposal
Packaging materials
The materials marked with the symbol
recyclable.
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where
you purchased the product.
are
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by disposing of
them properly in appropriate collection containers.
Machine
Use authorised disposal sites for your old appliance.
Help to keep your country tidy!
To save water, energy and to help protect the
environment, we recommend that you follow these
tips:
• With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature.
• Normally soiled laundry may be washed without
prewashing in order to save detergent, water and
time (the environment is protected too!).
• Measure out detergent according to the water
hardness, the degree of soiling and the quantity of
laundry being washed.
• The machine works more economically if it is fully
loaded.
Technical specifications
DIMENSIONS
Height
Width
Depth
85 cm
60 cm
34 cm
MAXIMUM LOAD
Cotton
Synthetics
Delicates
Woollens/Handwash
3 kg
1 kg
1 kg
0,8 kg
SPIN SPEED
1000 rpm max.
POWER SUPPLY VOLTAGE/FREQUENCY
TOTAL POWER ABSORBED
MINIMUM FUSE PROTECTION
220-230 V/50 Hz
1650 W
10 A
WATER PRESSURE
0,05 MPa
0,8 MPa
Minimum
Maximum
This appliance complies with the following EEC Directives:
73/23/EEC of 19/02/73 relating to low voltage
89/336/EEC of 03/05/89 relating to electromagnetic compatibility.
73
Downloaded From WashingMachine-Manual.com Manuals
ENGLISH
Tips for environmental protection
Installation
Positioning
Unpacking
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that the
machine does not touch the wall or other kitchen
units.
Carefully level by screwing the adjustable feet in or
out. Never place cardboard, wood or similar
materials under the machine to compensate for any
unevenness in the floor.
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so that
they can be refitted if the machine ever has to be
transported again.
1. Using a spanner, unscrew and remove the three
rear bottom screws.
P1129
P1051
2. Slide out the three plastic pins.
Water inlet
Connect the water inlet hose to a tap with a 3/4"
thread.
Do not use already employed hoses for water
connection.
The inlet hose is provided with a water stop device,
which protects against damage caused by water
leaks in the hose which could develop due to natural
ageing of the hose. This fault is shown by a red
sector in the window “A”. Should this occur, turn the
water tap off and refer to your Service Centre to
replace the hose.
P0001
3. Very carefully slide out the left polythene bag,
removing it towards the right and then
downwards..
A
P0352
P0002
74
Downloaded From WashingMachine-Manual.com Manuals
The other end of the inlet hose which connects to the
machine can be turned in any direction. Simply
loosen the fitting, rotate the hose and retighten the
fitting, making sure there are no water leaks
The drain hose must not be kinked.
P1118
For a correct functioning of the machine the
drain hose must remain hooked on the proper
support piece situated on the top part of the back
side of the appliance.
P0021
The inlet hose must not be lengthened. If it is too
short and you do not wish to move the tap, you will
have to purchase a new, longer hose specially
designed for this type of use.
This machine is designed to operate on a 220-230 V,
single-phase, 50 Hz supply.
Water drainage
Check that your domestic electrical installation can
take the maximum load required (1.65 kW), also
taking into account any other appliances in use.
The end of the drain hose can be positioned in three
ways:
Connect the machine to an earthed socket.
Hooked over the edge of a sink using the plastic
hose guide supplied with the machine. In this
case, make sure the end cannot come unhooked
when the machine is emptying.
This could be done by tying it to the tap with a piece
of string or attaching it to the wall.
The manufacturer declines any responsibility
for damage or injury through failure to comply
with the above safety precaution.
Should the appliance power supply cable
need to be replaced, this should be carried
out by our Service Centre.
Please ensure that when the appliance is
installed the power supply cable is easily
accessible.
P0022
In a sink drain pipe branch. This branch must be
above the trap so that the bend is at least 60 cm
above the ground.
Directly into a drain pipe at a height of not less
than 60 cm and not more than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain pipe
must be larger than the outside diameter of the drain
hose.
75
Downloaded From WashingMachine-Manual.com Manuals
ENGLISH
Electrical connection
Description of the appliance
1 Detergent dispenser drawer
1
2
2 Control panel
3 Door handle
Zeitvorwahl EWS 1030
Départ Différé
4 Drain pump
E in /A us
r che /A rrêt
Ma
Koch-/Buntwäsche
Coton
Pflegeleicht
Synthétiques
Feinwäsche
Délicats
Wolle/Laine
90°C
60°C
40°C
30°C
Kalt/Froid
1000
900
700
500
Spülstopp/
A.C.P.
Vorwäsche/
Prélavage
ECO
Spülen+
Rinçage+
St
e
D é pa rt / P au ss e
a r t / Pa u
5 Adjustable feet
3
4
5
Detergent dispenser drawer
Prewash
Main wash
Fabric softener, starch
C0069
76
Downloaded From WashingMachine-Manual.com Manuals
Use
Control panel
Zeitvorwahl EWS 1030
Départ Différé
M
E in / Au s
ar c h e /A rr ê
Koch-/Buntwäsche
Coton
Pflegeleicht
Synthétiques
Feinwäsche
Délicats
Wolle/Laine
t
90°C
60°C
40°C
30°C
1000
900
700
500
Kalt/Froid
Spülstopp/
A.C.P.
Vorwäsche/
Prélavage
Spülen+
Rinçage+
ECO
St
e
D é pa rt / P a u ss e
a r t/ Pau
2
3
4
5
6
7
8
9 11
10
Maximum temperatures are 90°C for cotton, 60°C for
synthetic fabrics, 40°C for delicate fabrics, wool and
fabrics to be hand-washed.
Position “Kalt/Froid” corresponds to cold wash.
1 ON/OFF button
(Ein/Aus - Marche/Arrêt)
Press this button to switch the washing machine on.
Press the
button again to switch the machine off.
5 SPIN SPEED button
2 MAINS-ON light
Press this button repeatedly to change the spin
speed, if you want your laundry to be spun at a
speed different from the one proposed by the
washing machine. The relevant light will light up.
This light is connected to the
button. It lights up
when you press the button, and goes out when you
press it again.
Maximum speeds are:
• for cotton: 1000 rpm;
• for synthetic fabrics, wool, and fabrics to be handwashed: 900 rpm;
• for delicate fabrics: 700 rpm.
3 FABRIC button
Press this button repeatedly to select the
programme on the basis of the type of laundry to be
washed. The light relevant to the selected
programme will light up. The washing machine will
propose a temperature and automatically select the
maximum spin value provided for the programme
you have chosen. You can change these values by
operating buttons 4 and 5.
RINSE HOLD position (Spülstopp/A.C.P): when
you choose this option, the machine will not drain the
water of the last rinse, so as not to wrinkle the
laundry.
At the end of the cycle, the light of the
START/PAUSE button
goes out and the door is
locked, the RINSE HOLD pilot light remains lit, to
indicate that the water must be drained. On the
display appears a blinking zero.
To complete the cycle, choose one of the following
options:
Hand wash
When you select this programme, you obtain a
particularly delicate washing, suitable for articles of
clothing whose label indicates that they must be
hand-washed
.
• Drain
4 TEMPERATURE button ºC
Press SKIP/RESET
button once, all the leds are off,
the display will show three blinking dashes, then press
button in order to select the desired programme. If
you wish to drain
or spin
press the
button until
the led of the desired function goes on. You can change
Press this button repeatedly to increase or decrease
the temperature, if you want your laundry to be
washed at a temperature different from the one
proposed by the washing machine. The relevant
light will light up.
77
Downloaded From WashingMachine-Manual.com Manuals
or Spin
ENGLISH
1
the spin speed by means of
Start/Pause
.
button and then depress
Important! If you accidentally press the
button
more than once, the display will show three blinking
dashes. To drain the water, select any washing
programme by means of the
button, then press
three times in order to select the DRAIN position
(only the DRAIN light
will remain lit).
--• Duration of washing programme in hours
and minutes, after you have selected a
programme.
6 OPTION button
Press these buttons to select the following options:
• PREWASH (Vorwäsche/Prélavage): select this
option if you wish your laundry to be prewashed
before the main wash (not available for wool
and hand wash
programmes).
2.05
The prewash ends with a short spin at 650 rpm in
programmes for cotton and synthetic fabrics,
whereas in the programme for delicate fabrics the
water is only drained.
• ECO: this option can be selected for cottons and
synthetics lightly or normally soiled with a
temperature of 40°C or higher.
Furthermore the washing temperature will be
reduced automatically and the washing time will be
prolonged.
While the programme is running (after you have
pressed the
button), the displayed time value
decreases by one unit every minute.
• The washing machine has stopped with water in
the tub, at the end of a programme with the
RINSE HOLD option: this is indicated by a
flashing zero.
• SUPER RINSE (Spülen+/Rinçage+): this option
can be selected with all programmes except the
wool
and hand wash
programmes. The
machine will add some additional rinses to the
selected programme. This option is recommended
for people who are allergic to detergents, and in
areas where the water is very soft.
• The washing machine has completed the
programme: this is indicated by a blinking zero.
The zero will reappear when you switch the
washing machine on, unless the previous
programme has been erased by means of the
button.
7 Display
The following pieces of information are shown on the
display:
0
• Three blinking dashes, when a programme is
cancelled by means of the
button.
The three blinking dashes will also appear when you
press the
button to switch the machine on, if the
previously selected cycle has been erased.
Important!
The first time you use the washing machine,
when you switch it on, it may display a blinking zero.
This is due to the fact that the washing machine has
performed a washing cycle during the manufacturer’s
inspection tests, and this cycle has not been erased
after its completion.
78
Downloaded From WashingMachine-Manual.com Manuals
• Delay start, a time value indicated in hours and
selected by means of the relevant button.
above the button will start flashing. To restart the
programme, press the button again.
When you PAUSE the cycle and it becomes
possible to open the door, provided
• the washing machine is not in the heating phase;
• the level of the water is not high;
• the drum is not turning.
Important! You must set the washing machine to
PAUSE before you make any change in the
programme in progress.
The delay time is displayed for 3 seconds, then the
duration of the selected programme reappears.
After you have pressed the
button, the
countdown begins, and the delay time value
decreases by one unit every hour.
You can delay the start of the selected programme
by up to 23 hours in one hour intervals.
9 SKIP/RESET button
• An incorrect option selection has been made: this
is indicated by the message Err when a function
incompatible with the current programme is selected.
You can also press the RESET button to exclude
one or several phases of the programme which is
running, as indicated below.
- set the washing machine to PAUSE by pressing the
START/PAUSE button (the relevant light will flash);
- press the RESET button once or several times, until
the required phase(s) is(are) cancelled (the light next
to the symbol of the phase(s) will go out).
Example:
In this case, the spin (at
the speed provided for
the selected type of
fabric) will be
performed.
• An alarm code indicates a fault in the machine
operation (see the relevant chapter on page 90).
E20
This button allows you also to select special
programmes, such as RINSES, SPIN and DRAIN.
• If the machine is already switched on because it
has just performed a washing programme, proceed
as follows:
9 START/PAUSE button
(Start/Pause - Départ/Pause)
- depress RESET once or repeatidly to cancel the
previously performed programme (three blinking
dashes will appear on the display);
- select the type of fabric by means of the relevant
button;
- select the special programme:
• RINSES
This button has two functions:
• Start: after you have selected the desired
programme and options, press this button to start
the washing machine. The light above the button
will stop flashing and remain lit.
If you have selected a delay time by means of
button 10, the countdown will begin and will be
shown on the display.
• Pause: when you press this button again, the
programme in progress is interrupted. The light
79
Downloaded From WashingMachine-Manual.com Manuals
ENGLISH
At the end of a programme, you must press this
button once or repeatedly, in order to clear the
contents of the memory (the display will show three
blinking dashes); otherwise, the next time you switch
the washing machine on, the blinking zero will
reappear.
If you need to open the door, you must first set the
washing machine to PAUSE by pressing the
START/PAUSE button. After you have closed the
door, press the START/PAUSE button again.
Depress RESET once, the pilot light WASH
goes out.
• SPIN
Depress RESET twice, the pilot lights WASH
and RINSES
go out.
• DRAIN
Depress RESET three times, the pilot lights
WASH
, RINSES
and SPIN
go out.
11 Programme phase indicator
lights
When you select a programme, the lights relevant to
the phases that form the programme light up.
Example:
PREWASH
In this case the
machine will perform
the rinses and spin.
WASH
RINSES
SPIN
DRAIN
• If the machine is switched off:
- depress ON/OFF button to switch it on;
- select the type of fabric by means of button
select the special programme as previously
described.
After you have started the programme, only the light
relevant to the phase that is currently being carried
out will remain lit.
;
10 DELAY START button
(Zeitvorwahl/Départ Différé)
This button makes it possible to delay the starting of
the programme from 30 min-60 min-90 min, 2 hours
and then by 1 hour up to maximum of 23 hours. The
delay you have selected is shown on the display for
about 3 seconds; afterwards, the duration of the
programme reappears.
You must select this option after you have set the
programme and before you press the
START/PAUSE button.
The time value shown on the display will decrease
by one unit every hour.
You can change the delay time at any moment,
before you press the START/PAUSE button.
If you have already pressed the START/PAUSE
button, and you wish to cancel the delay time,
proceed as follows:
• set the washing machine to PAUSE by pressing the
START/PAUSE button;
• press the DELAY button twice, to erase the delay
time. The display will indicate 0’.
• press the START/PAUSE button again.
Important!
The door will be locked throughout the delay time.
80
Downloaded From WashingMachine-Manual.com Manuals
Laundry weights
Washing hints
The following weights are indicative:
Follow the wash code symbols on each garment
label and the manufacturer’s washing instructions.
Sort the laundry as follows:
whites, coloureds, synthetics, delicates, woollens.
1200 g
napkin
100 g
quilt cover
700 g
sheet
500 g
pillow case
200 g
tablecloth
250 g
Temperatures
towelling towel
200 g
90°
tea cloth
100 g
60°
Cold
for normally soiled white cottons and linen
(e.g. tea cloths, towels, tablecloths,
sheets...)
for normally soiled, colour fast garments
(e.g. shirts, night dresses, pyjamas....) in
linen, cotton or synthetic fibres and for
lightly soiled white cotton (e.g. underwear).
for delicate items (e.g. net curtains), mixed
30°-40° laundry including synthetic fibres and
night dress
200 g
ladies’ briefs
100 g
man’s work shirt
600 g
man’s shirt
200 g
man’s pyjamas
500 g
blouse
100 g
men’s underpants
100 g
woollens.
Before loading the laundry
Removing stains
Never wash whites and coloureds together. Whites
may lose their “whiteness” in the wash.
Stubborn stains may not be removed by just water
and detergent. It is therefore advisable to treat them
prior to washing.
New coloured items may run in the first wash; they
should therefore be washed separately the first time.
Blood: treat fresh stains with cold water. For dried
stains, soak overnight in water with a special
detergent then rub in the soap and water.
Make sure that no metal objects are left in the
laundry (e.g. hair clips, safety pins, pins).
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and dab the
stain; treat several times.
Button up pillowcases, close zip fasteners, hooks
and poppers. Tie any belts or long tapes.
Remove persistent stains before washing. Rub
particularly soiled areas with a special detergent or
detergent paste.
Dried grease stains: moisten with turpentine, lay
the garment on a soft surface and dab the stain with
the fingertips and a cotton cloth.
Treat curtains with special care. Remove hooks or tie
them up in a bag or net.
Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with rust
stains which are not recent since the cellulose
structure will already have been damaged and the
fabric tends to hole.
Maximum loads
Recommended loads are indicated in the
programme charts.
Mould stains: treat with bleach, rinse well (whites
and fast coloureds only).
General rules:
Grass: soap lightly and treat with bleach (whites and
fast coloureds only).
Cotton, linen: drum full but not too tightly packed;
Synthetics: drum no more than half full;
Ball point pen and glue: moisten with acetone (*),
lay the garment on a soft cloth and dab the stain.
Delicate fabrics and woollens: drum no more than
one third full.
Lipstick: moisten with acetone as above, then treat
stains with methylated spirits. Remove any residual
marks from white fabrics with bleach.
Washing a maximum load makes the most efficient
use of water and energy.
For heavily soiled laundry, reduce the load size.
Red wine: soak in water and detergent, rinse and
treat with acetic or citric acid, then rinse. Treat any
residual marks with bleach.
81
Downloaded From WashingMachine-Manual.com Manuals
ENGLISH
bathrobe
Sorting the laundry
Ink: depending on the type of ink, moisten the fabric
first with acetone (*), then with acetic acid; treat any
residual marks on white fabrics with bleach and then
rinse thoroughly.
Quantity of detergent to be used
The type and quantity of detergent will depend on
the type of fabric, load size, degree of soiling and
hardness of the water used.
Tar stains: first treat with stain remover, methylated
spirits or benzine, then rub with detergent paste.
(*) do not use acetone on artificial silk.
Water hardness is classified in so-called “degrees” of
hardness. Information on hardness of the water in
your area can be obtained from the relevant water
supply company, or from your local authority.
Detergents and additives
Follow the product manufacturers’ instructions on
quantities to use.
Good washing results also depend on the choice of
detergent and use of the correct quantities to avoid
waste and protect the environment. Although
biodegradable, detergents contain substances
which, in large quantities, can upset the delicate
balance of nature.
Use less detergent if:
– you are washing a small load,
– the laundry is lightly soiled,
– large amounts of foam form during washing.
The choice of detergent will depend on the type of
fabric (delicates, woollens, cottons, etc.), the colour,
washing temperature and degree of soiling.
All commonly available washing machine detergents
may be used in this appliance:
– powder detergents for all types of fabric,
– powder detergents for delicate fabrics (60°C max)
and woollens,
– liquid detergents, preferably for low temperature
wash programmes (60°C max) for all types of
fabric, or special for woollens only.
The detergent and any additives must be placed in
the appropriate compartments of the dispenser
drawer before starting the wash programme.
If using concentrated powder or liquid detergents, a
programme without prewash must be selected.
The washing machine incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Pour liquid detergent into the dispenser drawer
compartment marked
just before starting the
programme.
Any fabric softener or starching additives must be
poured into the compartment marked
before
starting the wash programme.
Follow the product manufacturer’s recommendations
on quantities to use and do not exceed the «MAX»
mark in the detergent dispenser drawer.
82
Downloaded From WashingMachine-Manual.com Manuals
International wash code symbols
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
95
60
40
30
Max. wash
temperature
95°C
Max. wash
temperature
60°C
Max. wash
temperature
40°C
Max. wash
temperature
30°C
Delicate wash
60
Bleaching
Bleach in cold water
40
Hand wash
30
40
Do not
wash
at all
ENGLISH
Energetic wash
Do not bleach
Ironing
Hot iron
max 200°C
Warm iron
max 150°C
Lukewarm iron
max 110°C
Do not iron
Dry cleaning
Dry cleaning
in all solvents
Dry cleaning in
perchlorethylene,
petrol, pure alcohol,
R 111 & R 113
Dry cleaning
in petrol,
pure alcohol
and R 113
Do not
dry clean
high
temperature
low
temperature
Drying
Flat
On the line
On clothes
hanger
83
Downloaded From WashingMachine-Manual.com Manuals
Tumble dry
Do not
tumble dry
4. Switch the machine on
Operating sequence
Press the ON/OFF button
to switch the machine
on. The display will show three blinking dashes or a
blinking zero. The light above the button will light up.
Before the first wash we recommend that you pour 2
litres of water into the main wash compartment of the
detergent drawer in order to activate the ECO valve.
Then run a cotton cycle at 90°C, with the machine
empty, in order to remove any manufacturing residue
from the drum and tub. Pour half a measure of
detergent into the main wash compartment and start
up the machine.
Ein / A u s
r c h e /A rr êt
Ma
0
---
1. Place the laundry in the drum
Open the door.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible.
5. Select the desired programme/fabric
Press the FABRIC button
repeatedly, in order to
select the desired programme/fabric. The relevant
light will light up.
Close the door.
The lights relevant to the phases that form the
programme will light up.
The display will show the duration of the selected
programme, calculated on the basis of the maximum
load for each type of fabric. The START/PAUSE
button light will start flashing.
If the load of laundry to be washed is small, at the
beginning of the cycle the display will still indicate the
duration relevant to the maximum load. The duration
value will be gradually adjusted during the execution
of the cycle.
P0004
2. Measure out the detergent
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent recommended by the
manufacturer in a graduated cup and pour it into the
main wash compartment
.
Koch-/Buntwäsche
Coton
Pflegeleicht
Synthétiques
Feinwäsche
Délicats
Wolle/Laine
If you have selected the prewash
function, pour
detergent into the appropriate compartment marked
.
3. Measure out the additive
6. Select the temperature
If required, pour fabric softener into the compartment
marked
, without exceeding the «MAX» mark.
Press the TEMPERATURE button °C if you wish to
select a temperature value different from the one
proposed by the washing machine.
The relevant light will light up.
90°C
60°C
40°C
30°C
Kalt/Froid
C0070
C0071
84
Downloaded From WashingMachine-Manual.com Manuals
7. Select the spin speed
HOLD option
10. Start the programme
or the RINSE
Press the START/PAUSE button
. The relevant
light will stop flashing and only the light relevant to
the phase that is in progress will remain lit.
If you have chosen a delayed start, the washing
machine will begin the countdown.
The display will show the duration of the programme
or the selected delay.
Press the SPIN SPEED button
repeatedly, in
order to select the desired spin speed or the RINSE
HOLD option. The relevant light will light up.
If you select the RINSE HOLD option, the machine
will stop at the end of the programme with the water
still in the tub.
1000
900
700
500
Spülstopp/
A.C.P.
11. How to change a programme during
its cycle
8. Select the desired options
Depress the relevant button to select the required
options.
Before you make any change, you must pause the
washing machine by pressing the START/PAUSE
button.
It is possible to change any phase before the
programme carries it out.
Changing the type of fabric or temperature is
possible, obviously, only during the washing phase.
If it is necessary to drain the water in order to change
the programme in progress, proceed as follows:
Vorwäsche/
Prélavage
ECO
Spülen+
Rinçage+
• PAUSE the machine by pressing the
START/PAUSE button;
• press the SKIP/RESET button repeatedly, until
only the DRAIN light
remains lit;
9. Select the DELAY TIME
• press the START/PAUSE button again.
Before you start the programme, if you wish the
starting to be delayed, press the DELAY button (11)
repeatedly, or keep it pressed, to select the desired
delay. The selected delay time value (up to 23 hours)
will appear on the display for 3 seconds, then the
duration of the programme will appear again.
When the water has been drained, the display shows
a blinking zero. You may now select a new
programme and press the START/PAUSE button to
start it.
12. How to cancel a programme
during its cycle
Zeitvorwahl
Départ Différé
To cancel a programme that is being carried out, first
pause the washing machine by pressing the
START/PAUSE button, then press the SKIP/RESET
button repeatedly, until the display shows three
blinking dashes.
85
Downloaded From WashingMachine-Manual.com Manuals
ENGLISH
St
e
D é pa rt / P a u ss e
ar t/ Pau
13. How to open the door during the
cycle of a programme
You can open the door, after having set the washing
machine to PAUSE, provided the following
conditions exist:
Check whether the drum is completely empty, by
rotating it with your hand. The purpose of this is to
prevent any items of laundry from remaining
accidentally in the drum, where they might get
damaged in a subsequent wash (e.g. by shrinking) or
bleed colour into another load of laundry.
• the washing machine is not in the heating phase
beyond 55°C;
We advise you to close the water supply tap and
disconnect the plug from the socket.
• the level of the water is not high;
Leave the door ajar in order to air the washing
machine.
• the drum is not turning.
If these requirements are met, when you pause the
washing machine, the door can be opened.
Should it not be possible to open the door, and
should it be absolutely necessary to do so, switch
the machine off by pressing the ON/OFF button.
After approximately 3 minutes, you can open the
door.
Pay attention to the level and temperature of the
water in the washing machine!
When you close the door and press the ON/OFF
button again, the washing machine will resume the
programme from the point where it had been
interrupted.
14. End of programme
At the end of the programme, the washing machine
stops automatically and displays a blinking zero.
If you had selected the RINSE HOLD option,
START/PAUSE button
goes out and the door is
locked, the RINSE HOLD pilot light remains lit, to
indicate that the water must be drained. The display
shows a flashing zero.
When the programme has been completed, a
blinking zero appears on the display.
Press the SKIP/RESET button repeatedly to erase
the programme that has just been carried out. If
you omit to do this, the next time you switch the
washing machine on, the blinking zero will
appear on the display.
Note: when you switch the machine on, if you must
erase the previously performed programme, it is also
sufficient to press the FABRIC button
and select
a new programme.
Press the ON/OFF button to switch the machine off.
The relevant light will go out.
Remove the laundry from the washing machine.
86
Downloaded From WashingMachine-Manual.com Manuals
Washing programmes
60
40
3 kg
30
Coloured
cotton: e.g.
shirts, blouses,
underwear,
towels, household linen
**
Cottons +
ECO
3 kg
60
60
40
40
1 kg
30
Delicate fabrics: e.g.
acrylic fabrics,
viscose, polyester,
synthetic
blends
40
3 kg
30
Synthetic
fabrics and
blends: e.g.
shirts, blouses,
underwear
30
Programme/
temperature
Cottons
60°-90°C
95
White cotton:
e.g. sheets,
tablecloths,
household
linen
60
Max
load
1 kg
0,8 kg
Wool
0,8 kg
Description of
Available options
programme
Main wash at
60°-90°C
3 rinses
Long spin
Cottons
Main wash at
60°-40°-30°C- 60°-40°-30°C
Cold
and Cold
3 rinses
Long spin
Cottons
60° + ECO
Main wash at
60°
3 rinses
Long spin
Main wash at
Synthetics
60°-40°-30°C 60°-40°-30° or
cold wash
or Cold
3 rinses
Short spin
Delicates
40°-30°C
or Cold
Wool
40°-30°C
or Cold
Hand wash
40°-30°C
or Cold
Main wash at
40°-30°C or
cold wash
3 rinses
Short spin
Main wash at
40°-30°C or
cold wash
3 rinses
Short spin
Main wash at
40°-30°C or
cold wash
3 rinses
Short spin
*
Consumption*
Energy kWh
Water
litres
1.5
42
0.85
39
0.57
39
/RINSE HOLD
PREWASH
ECO
SUPER RINSE
0.65
42
/RINSE HOLD
PREWASH
ECO
SUPER RINSE
0.4
47
0.35
50
0.35
50
/RINSE HOLD
PREWASH
ECO
SUPER RINSE
/RINSE HOLD
PREWASH
ECO
SUPER RINSE
/RINSE HOLD
ECO
/RINSE HOLD
/RINSE HOLD
The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on
the quantity and type of laundry, on the inlet water temperature and on the ambient temperature. It refers to
the highest temperature for each wash programme.
** In compliance with EC directive 92/75 the consumption figures indicated on the Energy label refer to this
programme at 60°C + ECO.
The wool wash cycle of this machine has been approved by Woolmark for the washing of machine washable
Woolmark products provided that the garments are washed according to the instructions on the garment label
and those issued by the manufacturer of this machine. Licence No. M9604.
87
Downloaded From WashingMachine-Manual.com Manuals
ENGLISH
Type of
laundry and
symbols on
labels
Maintenance
1. Door seal
Detergent can also accumulate inside the drawer
recess: clean it with an old toothbrush. Refit the
drawer after cleaning.
Check from time to time the door seal and eliminate
eventual possible objects that could be trapped in
the fold.
P0038
P1050
Drain pump
2. Bodywork
The pump should be inspected if
Clean the outside of the machine with warm water
and a neutral, non-abrasive household detergent.
Rinse with clean water and dry with a soft cloth.
• the machine does not empty and/or spin
• the machine makes an unusual noise during
draining due to objects such as safety pins, coins
etc. blocking the pump.
Important: do not use methylated spirits, solvents or
similar products to clean the bodywork.
Proceed as follows:
• Disconnect the appliance.
• If necessary wait until the water has cooled down.
• Open the pump door.
3. Detergent dispenser drawer
After a while, detergents and fabric softeners leave
deposits in the drawer.
Clean the drawer from time to time by rinsing it under
a running tap. To remove the drawer from the
machine, press the button in the rear left-hand
corner.
To facilitate cleaning, the top part of the additive
compartment can be removed.
P1114
C0072
• Place a container close to the pump to collect any
spillage.
• Release the emergency emptying hose, place it in
the container and remove its cap.
• When no more water comes out, unscrew the
pump and remove it. Always keep a rag nearby to
dry up spillage of water when removing the pump.
C0073
P1115
C0068
P1086
88
Downloaded From WashingMachine-Manual.com Manuals
Emergency emptying out
• Remove any objects from the pump impeller by
rotating it.
If the water is not discharged, proceed as follows to
empty out the machine:
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• open the pump door;
• place a bowl on the floor and place the end of the
emergency emptying hose into the bowl. Remove
its cap. The water should drain by gravity into the
bowl. Whe the bowl is full, put the cap back on the
hose. Empty the bowl. Repeat the procedure until
water stops flowing out;
• Put the cap back on the emergency emptying
hose and place the latter back in its seat.
• clean the pump if necessary as previously
described;
• replace the emergency emptying hose in its seat
after having plugged it;
P1117
ENGLISH
• screw the pump cover again and close the door.
Frost precautions
• Screw the pump cover fully in.
• Close the pump door.
If the machine is installed in a place where the
temperature could drop below 0°C, proceed as
follows:
Water inlet filter
• Remove the plug from the socket.
• Close the water tap and unscrew the water inlet
hose from the tap.
If you notice that the machine is taking longer to fill,
check that the filter in the water inlet hose is not
blocked.
Turn off the water tap.
• Place the end of the emergency emptying hose
and that of the inlet hose in a bowl placed on the
floor and let water drain out.
Unscrew the hose from the tap.
• Switch the machine OFF by depressing button
Clean the filter with a stiff brush.
• Screw the water inlet hose back on and reposition
the emergency emptying hose after having put the
cap on again.
Screw the hose back onto the tap.
.
By doing this, any water remaining in the machine is
removed, avoiding the formation of ice and,
consequently, breakage of the affected parts.
When you use the machine again, make sure that
the ambient temperature is above 0°C.
Important!
Every time you drain the water through the
emergency emptying hose you must pour 2 litres of
water into the main wash compartment of the
detergent drawer and then run the drain
programme. This will activate the ECO VALVE
device avoiding that part of the detergent remains
unused at next washing.
P1090
89
Downloaded From WashingMachine-Manual.com Manuals
Something not working?
Problems which you can resolve yourself.
During machine operation it is possible that one of the following alarm codes appears on the display:
- E10: problem with the water supply
- E20: problem with water draining
- E40: door open
Once the problem has been eliminated, press the START/PAUSE button
to restart the programme. If after
all checks, the problem persists, contact your local Service Centre.
Problem
Possible cause
• The machine does not start up:
• The door is not firmly closed. (E40)
• The machine is not plugged in or there is no power
at the socket.
• The main fuse has blown.
• The START/PAUSE button has not been
depressed.
• The DELAY START option has been selected.
• The machine does not fill:
•
•
•
•
• The machine fills then empties
immediately:
• The end of the drain hose is too low. Refer to
relevant paragraph in “water drainage” section.
• The machine does not empty
and/or does not spin:
• The drain hose is squashed or kinked. (E20)
• The RINSE HOLD option has been selected.
• The drain pump is clogged. (E20)
• There is water on the floor:
• Too much detergent or unsuitable detergent
(creates too much foam) has been used.
• Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this
as the water runs down the hose; check to see if it
is damp.
• The drain hose is damaged.
• The drain pump cover has not been screwed in
after cleaning.
• The emergency emptying hose has not been
plugged after cleaning the pump.
• Unsatisfactory washing results:
• Too little detergent or unsuitable detergent has
been used.
• Stubborn stains have not been treated prior to
washing.
• The correct temperature was not selected.
• Excessive laundry load.
• The machine vibrates or is
noisy:
• The transit bolts and packing have not been
removed.
• The support feet have not been adjusted.
• The laundry is not evenly distributed in the drum.
• Maybe there is very little laundry in the drum.
90
Downloaded From WashingMachine-Manual.com Manuals
The water tap is closed. (E10)
The inlet hose is squashed or kinked. (E10)
The filter in the inlet hose is blocked. (E10)
The door is not properly closed. (E40)
Possible cause
• The door will not open:
• The water level is above the bottom edge of the door.
• The machine is heating the water.
• The drum is turning.
• Spinning starts late or the
laundry is not spun enough:
• The electronic unbalance detection device has cut
in because the laundry is not evenly distributed in
the drum. The laundry is redistributed by reverse
rotation of the drum. This may happen several
times before the unbalance disappears and normal
spinning can resume. If, after 5 minutes, the
laundry is still not evenly distributed in the drum,
the machine will spin at a lower speed. If at the end
of the programme the laundry is not spun enough,
redistribute the load manually and select the spin
programme.
• Water is not visible in the
machine:
• The machine, which is the result of modern
technology, runs in a very economical way with low
water consumption. Performance is nevertheless
excellent.
• The machine makes an unusual
noise:
• The machine is fitted with a commutator motor
which improves machine performance.
If you are unable to identify or solve the problem,
contact our service centre. Before telephoning, make
a note of the model, serial number and purchase
date of your machine: the Service Centre will require
this information. Service Centre List at page 92.
Mo
Pro d. .....
d.
No .....
. .....
.....
.
Ser
. No
. .....
....
Mod. ..........
Prod. No. ...........
P0042 BD
Ser. No. .........
91
Downloaded From WashingMachine-Manual.com Manuals
ENGLISH
Problem
KUNDENDIENST
Servicestellen
Points de service
Servizio dopo vendita
5506 Mägenwil/Zürich
Industriestr. 10
1028 Préverenges
Le Trési 6
6916 Grancia
Zona Industriale E
Ersatzteilverkauf
Point de vente de
rechange
Vendita pezzi di ricambio
5506 Mägenwil
Industriestrasse 10
Tel. 0848 848 023
5506 Mägenwil
Industriestrasse 10
Tel. 0848 848 023
5506 Mägenwil
Industriestrasse 10
Tel. 0848 848 023
Fachberatung / Verkauf
Demonstration / Vente
Consulente (cucina) /
Vendita
8048 Zürich
Badenerstrasse 587
Tel. 044 405 81 11
8048 Zürich
Badenerstrasse 587
Tel. 044 405 81 11
8048 Zürich
Badenerstrasse 587
Tel. 044 405 81 11
Garantie
Garantie
Garanzia
Für jedes Produkt gewähren wir ab
Verkauf bzw. Lieferdatum an den
Endverbraucher eine Garantie von 2
Jahren. (Ausweis durch Garantieschein, Faktura oder Verkaufsbeleg).
Die Garantieleistung umfasst die
Kosten für Material, Arbeits- und
Reisezeit.
Nous octroyons sur chaque produit
2 ans de garantie à partir de la date
de livraison ou de la mise en service
au consommateur (documenté au
moyen d’une facture, d’un bon de
garantie ou d’un justificatif d’achat).
Notre garantie couvre les frais de
mains d’œuvres et de déplacement,
ainsi que les pièces de rechange.
Per ogni prodotto concediamo una
garanzia di 2 anni a partire dalla
data di consegna o dalla sua messa
in funzione. (fa stato la data della
fattura, del certificato di garanzia o
dello scontrino d’acquisto )
Nella garanzia sono comprese le
spese di manodopera, di viaggio e
del materiale.
Die Garantieleistung entfällt bei
Nichtbeachtung der Gebrauchsanweisung und Betriebsvorschriften,
unsachgerechter Installation, sowie
bei Beschädigung durch äussere
Einflüsse, höhere Gewalt, Eingriffe
Dritter und Verwendung von NichtOriginal Teilen.
Les conditions de garantie ne sont
pas valables en cas d’intervention
d’un tiers non autorisé, de l’emploi
de pièces de rechange non
originales, d’erreurs de maniement
ou d’installation dues à l’inobservation du mode d’emploi, et pour
des dommages causés par des
influences extérieures ou de force
majeure.
Dalla copertura sono esclusi il
logoramento ed i danni causati da
agenti esterni, intervento di terzi,
utilizzo di ricambi non originali o
dalla inosservanza delle prescrizioni
d’istallazione ed istruzioni per l’uso.
9000 St. Gallen
Zürcherstrasse 204 e
4127 Birsfelden
Hauptstrasse 52
6032 Emmen
Buholzstrasse 1
7000 Chur
Comercialstrasse 19
3063 Ittigen/Bern
Ey 5
Downloaded From WashingMachine-Manual.com Manuals
The Electrolux Group. The world’s No. 1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in
more than 150 countries around the world.
Downloaded From WashingMachine-Manual.com Manuals