Samsung 275C - SRP Two-color Dot-matrix Printer Service manual

Service Manual
SRP-275
Impact Printer
Rev. 2.00
http://www.samsungminiprinters.com
SRP-275
■ Table of Contents
1. Precaution Segment ................................................................................................................................ 6
1-1 Safety Precautions............................................................................................................................... 6
1-2 Servicing Precaution............................................................................................................................ 7
1-3 Precaution for Electrostatically Sensitive Devices(ESDs) ................................................................... 7
1-4 Introduction .......................................................................................................................................... 8
2. Installation and Operation ...................................................................................................................... 9
2-1 Installation............................................................................................................................................ 9
2-1-1 AC Adapter Installation ................................................................................................................. 9
2-1-2 Interface cable and Cash Drawer cable Installation ..................................................................... 9
2-1-3 Ribbon Cartridge Installation....................................................................................................... 10
2-1-4 Paper Roll Installation ................................................................................................................. 11
2-1-5 Changing the paper width ........................................................................................................... 12
2-1-6 Wall Mount Installation................................................................................................................ 13
2-2 Operation ........................................................................................................................................... 14
2-2-1 Using the operation panel ........................................................................................................... 14
2-2-2 ERROR LED blinking pattern...................................................................................................... 15
2-2-3 Hexadecimal Dumping................................................................................................................ 16
2-2-3 The self Test Mode ..................................................................................................................... 16
2-3 Setting the Dip Switches.................................................................................................................... 18
2-3-1 DIP Switch setting for Epson(ESC/POS) mode.......................................................................... 18
2-3-2 DIP Switch setting for Citizen(iDP 3550) mode .......................................................................... 19
2-3-3 DIP Switch setting for Star(SP500) mode................................................................................... 20
2-3-4 Changing the DIP Switch setting ................................................................................................ 21
2-4 Setting the Memory Switches ............................................................................................................ 22
2-4-1 Memory Switch setting for Epson(ESC/POS) mode................................................................... 22
2-4-2 Memory Switch setting for Star mode......................................................................................... 26
3. Product Specifications.......................................................................................................................... 32
3-1 Appearance........................................................................................................................................ 32
3-1-1 Printer Dimensions (mm) ............................................................................................................ 32
3-1-2 AC Adapter Dimensions (mm) .................................................................................................... 32
3-1-3 Feature Locations ....................................................................................................................... 33
3-2 General Specifications....................................................................................................................... 34
3-3 Reference information ....................................................................................................................... 35
3-3-1 Printer Mechanism Specification ................................................................................................ 35
3-3-2 Printing Specification .................................................................................................................. 35
3-3-3 Character Specification............................................................................................................... 37
3-3-4 Paper Specification ..................................................................................................................... 38
3-3-5 Ribbon Cassette Specification .................................................................................................... 38
3-3-6 Environment Conditions.............................................................................................................. 39
3-3-7 Reliability..................................................................................................................................... 40
3-3-8 Certification ................................................................................................................................. 40
3-3-9 Printer(SMP715) pin Descriptions .............................................................................................. 40
3-3-10 Printer Head Specification ........................................................................................................ 41
3-3-11 Printer Head Thermistor Specification ...................................................................................... 41
3-3-12 PF(Paper Feed) Motor Specification ........................................................................................ 41
3-3-13 HF(Head Feed) Motor Specification ......................................................................................... 42
3-3-14 Auto Cutter Specification .......................................................................................................... 42
3-3-15 Switch(Sensor) Specification .................................................................................................... 42
3-4 SMPS Specifications ......................................................................................................................... 42
3-4-1 SMPS (Switching Mode Power Supply) Specification ................................................................ 42
3-4-2 SMPS Output Connector ............................................................................................................ 42
3-5 Interface Specifications...................................................................................................................... 43
3-5-1 RS-232C Serial Interface ............................................................................................................ 43
3-5-2 IEEE1284 Parallel Interface........................................................................................................ 45
3-5-3 USB Interface.............................................................................................................................. 46
3-6 Drawer Kick-Out Specifications ......................................................................................................... 47
3-6-1 Drawer Cable .............................................................................................................................. 47
3-6-2 Cable Connection ....................................................................................................................... 47
Rev. 2.00
-2-
SRP-275
4. Hardware ................................................................................................................................................ 48
4-1 Wiring Diagram .................................................................................................................................. 48
4-1-1 Main board wiring diagram.......................................................................................................... 48
4-1-2 Connector sub PCB wiring diagram............................................................................................ 49
4-2 Block Diagram.................................................................................................................................... 50
4-3 PCB Layout & Part List ...................................................................................................................... 51
4-3-1 Main Board.................................................................................................................................. 51
4-4-2 ASSY-PCB-CONNECTOR SUB ................................................................................................. 57
4-4-3 ASSY-OPERATION PANEL ....................................................................................................... 58
4-4-4 ASSY-PCB-HEAD....................................................................................................................... 59
4-4-5 Serial Interface (RS-232C).......................................................................................................... 60
4-4-6 Parallel Interface (IEEE1284) ..................................................................................................... 61
4-4-7 USB Interface.............................................................................................................................. 62
4-4-8 Ethernet Interface ....................................................................................................................... 63
4-5 Schematic Diagram ........................................................................................................................... 65
4-5-1 Main Circuit Diagram .................................................................................................................. 65
4-5-2 Head circuit diagram ................................................................................................................... 74
4-5-3 Serial Interface Diagram (RS-232C)........................................................................................... 75
4-5-4 Parallel Interface Diagram (IEEE-1284) ..................................................................................... 76
4-5-5 USB Interface Diagram (Universal Serial Bus) ........................................................................... 77
5. Disassembly and Assembly ................................................................................................................. 78
5-1 SMP715 Printer mechanism unit Sub-assembly ............................................................................... 78
5-1-1 Frame-main caulking assy .......................................................................................................... 78
5-1-2 Ribbon-feeder assy..................................................................................................................... 78
5-1-3 Lever-ribbon-feeder assy ............................................................................................................ 79
5-1-4 Lever-tension assy...................................................................................................................... 79
5-1-5 Carriage head assy..................................................................................................................... 80
5-1-6 Head-cover assy ......................................................................................................................... 80
5-1-7 Frame basket-A assy .................................................................................................................. 81
5-1-8 Frame basket-C assy.................................................................................................................. 82
5-1-9 Frame-holder basket-L assy ....................................................................................................... 83
5-1-10 Frame-holder basket-L caulking assy....................................................................................... 83
5-1-11 Frame-holder basket-R caulking assy ...................................................................................... 83
5-1-12 Frame-housing cutter lower assy.............................................................................................. 84
5-1-13 Cutter lower assy ...................................................................................................................... 84
5-1-14 Frame-rotator assy.................................................................................................................... 85
5-1-15 Holder platen assy .................................................................................................................... 86
5-2 SMP715 Printer mechanism unit Main-assembly.............................................................................. 87
5-2-1 Main-assembly A ........................................................................................................................ 87
5-2-2 Main-assembly B ........................................................................................................................ 88
5-2-3 Main-assembly C ........................................................................................................................ 89
5-2-4 Main-assembly D ........................................................................................................................ 90
5-2-5 Main-assembly E (for SMP715A type)........................................................................................ 91
5-2-6 Main-assembly E (for SMP715C type) ....................................................................................... 92
5-3 Auto cutter unit assembly .................................................................................................................. 93
5-3-1 AC timing belt assy ..................................................................................................................... 93
5-3-2 AC upper frame caulking assy .................................................................................................... 93
5-3-3 AC upper cutter guide assy......................................................................................................... 94
5-3-4 AC upper cutter assy .................................................................................................................. 94
5-3-5 AC motor assy............................................................................................................................. 95
5-3-6 AC motor sub assy...................................................................................................................... 95
5-3-7 PCB-AC assy .............................................................................................................................. 95
5-3-8 Main assy .................................................................................................................................... 96
Rev. 2.00
-3-
SRP-275
5-4 SRP-275 Whole unit Sub-assembly .................................................................................................. 97
5-4-1 Cover base assy ......................................................................................................................... 97
5-4-2 Switch-paper near end assy ....................................................................................................... 98
5-4-3 Switch-paper end assy................................................................................................................ 98
5-4-4 Cover middle assy ...................................................................................................................... 99
5-4-5 Switch-cover open assy ............................................................................................................ 100
5-4-6 Switch-paper near end -W assy................................................................................................ 100
5-4-7 Bracket PCB assy ..................................................................................................................... 101
5-4-8 Serial interface assy.................................................................................................................. 102
5-4-9 cover front-A assy ..................................................................................................................... 102
5-5 SRP-275 Whole unit Main-assembly............................................................................................... 103
5-5-1 Main-assembly A (for SRP-275A type)..................................................................................... 103
5-5-2 Main-assembly A (for SRP-275C type)..................................................................................... 105
5-5-3 Main-assembly B ...................................................................................................................... 107
5-5-4 Main-assembly C ...................................................................................................................... 109
5-5-5 Main-assembly D ...................................................................................................................... 110
6. Adjustments and Maintenance........................................................................................................... 112
6-1 Adjustment ....................................................................................................................................... 112
6-1-1 Adjustment of Head gap ........................................................................................................... 112
6-1-2 Replacement of Printer-head .................................................................................................... 112
6-2 Maintenance .................................................................................................................................... 113
6-2-1 Cleaning .................................................................................................................................... 113
6-2-2 Inspection.................................................................................................................................. 113
6-3 Lubricants and adhesive application ............................................................................................... 114
6-3-1 Lubricant requirements ............................................................................................................. 114
6-3-2 Lubricant types.......................................................................................................................... 114
6-3-3 Lubrication points...................................................................................................................... 114
6-3-4 Adhesive application requirements........................................................................................... 114
6-3-5 Adhesive types.......................................................................................................................... 114
6-3-6 Adhesive application points ...................................................................................................... 114
6-4 Tools, lubricants and adhesives ...................................................................................................... 115
6-4-1 List of tools ................................................................................................................................ 115
6-4-2 List of lubricants and adhesives................................................................................................ 115
7. Troubleshooting .................................................................................................................................. 116
7-1 Troubleshooting flow chart............................................................................................................... 116
A. POWER LED does not light ........................................................................................................... 117
B. PAPER LED is lit............................................................................................................................ 118
C. ERROR LED is blink...................................................................................................................... 119
D. ERROR LED is lit........................................................................................................................... 120
E. Self test is not normal .................................................................................................................... 121
F. Data from host is not printed normally ........................................................................................... 122
7-2 Troubleshooting flow tables ............................................................................................................. 123
7-2-1 Initialization problems ............................................................................................................... 124
7-2-2 Printing quality problems........................................................................................................... 125
7-2-3 Printer mechanism problems .................................................................................................... 126
7-2-4 Auto cut mechanism problems.................................................................................................. 127
8. Appendix (Mechanism operating principles).................................................................................... 128
8-1 Transport mechanism ...................................................................................................................... 128
8-1-1 Head feeding system ................................................................................................................ 128
8-1-2 Paper feeding system ............................................................................................................... 129
8-1-3 Ribbon feeding system ............................................................................................................. 130
8-1-4 Color changing system ............................................................................................................. 130
8-2 Printing mechanism ......................................................................................................................... 131
8-3 Detection mechanism ...................................................................................................................... 132
8-3-1 Home position detection mechanism........................................................................................ 132
8-3-2 Paper near end detection mechanism ...................................................................................... 133
8-3-3 Paper end detection mechanism .............................................................................................. 134
8-3-4 Rear cover open detection mechanism .................................................................................... 134
8-3-5 Auto cutter home position detection mechanism ...................................................................... 134
8-4 Auto cutter mechanism .................................................................................................................... 135
8-5 Easy paper loading mechanism....................................................................................................... 136
Rev. 2.00
-4-
SRP-275
■ About
About this Manual
This Service Manual describes how to perform hardware service maintenance for the BIXOLON SRP-275
Impact Printer.
Notes
Notes may appear anywhere in the manual. They draw your attention to additional information about the item.
Precaution symbols
NOTICE
Indicates a Safety Precaution that applies to this part component.
CAUTION
Use caution when handling these parts.
Copyright
ⓒ 2005 by BIXOLON Co., Ltd. All right reserved.
This Manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any
electronic or machine readable from without prior written permission or BIXOLON Co., Ltd.
■ Overview of this Receipt Printer
This System Impact Printer is a microprocessor-based system, using a 32 bit-microprocessor.
This Service Manual provides the technical information for many individual component systems, circuits and
gives an analysis of the operations performed by the circuits. If you need more technical information, please
contact our service branch or R&D center. Schematics and specifications provide the needed information for
the accurate troubleshooting.
All information in this manual is subject to change without prior notice. Therefore, you must check the
correspondence of your manual with your machine. No part of this manual may be copied or reproduced in
any form or by any means, without the prior written consent of BIXOLON Co., Ltd.
Rev. 2.00
-5-
SRP-275
1. Precaution Segment
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential
hazards such as electrical shock.
1-1 Safety Precautions
1. Be sure that all built-in protective devices are in place. Restore any missing protective shields.
2. When re-installing chassis and assemblies, be sure to restore all protective devices, including control
knobs and compartment covers.
3. Make sure that there are no cabinet openings through which people- particularly children might insert
fingers or objects and contact dangerous voltages. Such openings include excessively wide cabinet
ventilation slots and improperly fitted covers and drawers.
4. Leakage Current Hot Check :
WARNING : Do not use an isolation transformer during this test.
Use a leakage-current tester or metering system that complies with American National Standards Institute
(ANSI C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410,
59.7).
With the unit completely reassembled. plug the AC line cord directly into 110V AC or 240V outlet of the
Adapter. With the unit’s AC switch first in the ON position and then OFF. Measure the current between a
known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts,
including : metal cabinet, frame, screwheads and printer. The current measured should not exceed 0.1
milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test.
5. Design Alteration Warning :
Never alter or add to the mechanical or electrical design of the Receipt Printer. Unauthorized alterations
might create a safety hazard. Also, any design changes or additions will void the manufacturer’s warranty.
6. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be
replaced with parts that meet the original specifications. Always determine the cause of damage or
overheating, and correct any potential hazards.
7. Observe the original lead dress, especially near the following areas : sharp edges, and especially the AC
and high voltage supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the
spacing between components and the printed circuit board. Check the AC power cord for damage. Make
sure that leads and components do not touch thermally hot parts.
8. Product Safety Notice :
Some electrical and mechanical parts have special safety-related characteristics which might not be
obvious from visual inspection. These safety features and the protection they provide could be lost if a
replacement component differs from the original. This holds true, even though the replacement may be
rated for higher voltage, wattage, etc.
Components that are critical for safety are indicated in the circuit diagram by shading, ( or ). Use only
replacement components that have the same ratings, especially for flame resistance and dielectric
specifications. A replacement part that does not have the same safety characteristics as the original might
create shock, fire or other safety hazards.
Rev. 2.00
-6-
SRP-275
1-2 Servicing Precaution
WARNING 1 : First read the “Safety Precautions” section of this manual. If some unforeseen circumstance
creates a conflict between the servicing and safety precautions, always follow the safety
precautions.
WARNING 2 : An electrolytic capacitor installed with the wrong polarity might explode.
1. Always unplug the unit’s AC power cord from the AC power source or the Power Switch off before
attempting to :
(a) Remove or reinstall any component or assembly,
(b) Disconnect an electrical plug or connector,
(c) Connect a test component in parallel with an electrolytic capacitor.
2. Some components are raised above the printed circuit board for safety. An insulation tube or tape is
sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot
components. Reinstall all such elements to their original position.
3. After servicing, always check that the screws, components and wiring have been correctly reinstalled.
Make sure that the portion around the serviced part has not been damaged.
4. Check the insulation between the blades of the AC plug and accessible conductive parts(examples : metal
panels and input terminals).
5. Insulation Checking Procedure : Disconnect the power cord from the AC source and turn the power switch
ON. Connect an insulation resistance meter (500V) to the blades of the AC plug. The insulation resistance
between each blade of the AC plug and accessible conductive parts (see above) should be greater then 1
mega-ohm.
6. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit(or any of its assemblies)
unless all solid-state heat sinks are correctly installed.
7. Always connect an instrument’s ground lead to the instrument chassis ground before connecting the
positive lead; always remove the instruments ground lead last.
1-3 Precaution for Electrostatically Sensitive Devices(ESDs)
1. Some semiconductor(“solid state”) devices are easily damaged by static electricity. Such components are
called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some fieldeffect transistors. The following techniques will reduce the occurrence of component damage caused by
static electricity.
2. Immediately before handling any semiconductor components or assemblies. drain the electrostatic charge
from your body by touching a known earth ground. Alternatively, wear a discharging wriststrap device. (Be
sure to remove it prior to applying power-this is an electric shock precaution.)
3. After removing an ESD-equipped assembly. Place it on a conductive surface such as aluminum foil to
prevent accumulation of electrostatic charge.
4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs.
5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs.
6. Use only an anti-static solder removal device. Many solder removal devices are not rated as “anti-static;”
these can accumulate sufficient electrical charge to damage ESDs.
7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most
replacement ESDs are packaged with leads that are electrically shorted together by conductive foam,
aluminum foil or other conductive materials.
8. Immediately before removing the protective material from the leads of a replacement ESD, touch the
protective material to the chassis or circuit assembly into which the device will be installed.
9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes
together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.
Rev. 2.00
-7-
SRP-275
1-4 Introduction
The SRP-275 is a high-quality impact dot matrix POS printer.
This one-station printer has the following features.
• Compact design and light-weight.
• High-speed printing using logic-seeking.
• Easy to use : Easy paper loading.
• High reliability and long life due to the use of stepping motors for head carriage return and paper feeding.
• Two color printing (red/black) available.
• Various formats are possible because the paper feeding pitch is selectable.
• High general control utility based on the ESC/POS(TM) standard.
• The head can be driven due to the internal drawer interface.
• Character font (7ⅹ9, 9ⅹ9) is selectable.
• The auto cutter uses a circular method with a high-quality blade and a long life
(Approximately 1,000,000 cuts).
• Paper near end Switch is standard.
• A internal AC adaptor.
• Please be sure to read the instructions in this manual carefully before using your new printer.
Rear cover
Open button
DIP Switch cover
Power connect
Front cover
Interface
connector
Drawer kick-out
connect
Control panel
Power switch
[Front view]
Rev. 2.00
[Rear view]
-8-
SRP-275
2. Installation and Operation
2-1 Installation
2-1-1 AC Adapter Installation
1) Make sure the printer is turned off.
AC adaptor
2) Before inserting the AC adaptor, connect the
Power connector
power cord.
3) Insert the AC adaptor as shown.
4) Plug the AC adapter cable into the printer’s power
connector.
Power cord
5) Plug the power cord into the outlet, and turn on the
power.
CAUTION
Before connecting the printer to the power supply, make sure that the voltage and power specifications
match the printer’s requirements. Using an incorrect power supply can cause serious damage to the
printer.
2-1-2 Interface cable and Cash Drawer cable Installation
Interface
connector
1) Turn off printer and the host ECR (host computer).
2) Plug the interface cable into the interface
Drawer kick-out connector
connector on the printer then fasten the screw on
both sides of the connector.
3) Plug the drawer kick-out cable into the drawer kickout connector on the printer.
(When removing the drawer kick-out cable, press
on the connector’s clip while pulling out.)
Drawer kick-out
cable
Serial/ Parallel/ USB/ Ethernet
Interface cable
NOTES
Connect the printer to the host ECR (host computer) though an interface cable matching the specification
of the printer and the host ECR (host computer). Be sure to use a drawer that matches the printer’s
specification.
Depending on the interface your system uses, either connect the serial, parallel, USB or Ethernet
communication cable to the appropriate connector on the back of the printer. Cables are provided by your
dealer or system installer.
Rev. 2.00
-9-
SRP-275
2-1-3 Ribbon Cartridge Installation
1) Before inserting the ribbon cassette, turn the knob
clockwise to prevent twisting the ribbon.
2) Open the front cover of printer.
3) Take out the old ribbon cassette if there is one.
4) Insert the new ribbon cassette as shown and pay
particular attention to the placement of the ribbon in
front of the Printer Head.
5) During inserting the ribbon cassette, turn the knob
clockwise again to make sure the ribbon moves
freely in the cassette.
6) Close front cover of printer.
NOTES
Malfunctions and other problems may arise if other than specified ribbon cassettes are used in the printer.
The Warranty may be void if other than specified ribbon cassettes are used. Contact your dealer or place
of purchase for more information about proper ribbon cassettes.
Rev. 2.00
- 10 -
SRP-275
2-1-4 Paper Roll Installation
1) To prevent data loss, make sure that the printer is
not receiving data.
2) Open the rear cover by pushing the open button and
push the arrow mark back.
3) Remove the used paper roll core if there is one.
4) Insert the paper roll as shown.
5) Be sure to note the correct direction that the paper
should come off the paper roll.
6) Pull out small amount of paper as shown. Then close
the cover and tear off the extra paper by pulling it
toward the front of the printer.
CAUTION
Do not touch the auto cutter blade when you open rear cover.
Rev. 2.00
- 11 -
SRP-275
2-1-5 Changing the paper width
Screw(3x6)(2pieces)
1) Open the rear cover.
Frame paper control
2) Remove the Frame paper control by loosing the two
screws(3×6).
3) Reattach the Frame paper control in your wanting
position. (Insert and tighten two screws(3×6) to
reattach.)
4) Close the rear cover.
57.5mm
69.5mm 76mm(default)
5) Change the Memory Switch setting for changing
paper roll width. (See the instructions "Setting the
Memory Switches" in 2-2.Operation)
Rev. 2.00
- 12 -
SRP-275
2-1-6 Wall Mount Installation
Bracket hanger
1) Turn the Set over and attach the Bracket hanger to
the Frame base then tighten four screws.
Screw(3x5)
(4pieces)
Bracket mount
2) Attach the Bracket mount to the wall firmly with the
eight screws. Be sure that the Bracket attached
properly to match the direction of arrow as shown.
And the Bracket mount should be always fixed
Screw(4x10)
(8pieces)
vertically.
3) Insert the Bracket hanger of Set to the Bracket mount
as shown.
Rev. 2.00
- 13 -
SRP-275
2-2 Operation
2-2-1 Using the operation panel
Most of the functions of this printer are governed by software, but you can monitor the printer s status by
looking at the lights on the control panel and for some procedures you will use the buttons.
• Control panel
- POWER LED (Green Color)
This indicator light is on when the power is turned on. It blinks when the printer is in the self
test printing standby state. Always wait until this indicator light stops blinking before you
start using the printer and before you turn it off.
- ERROR LED (Red Color)
When this indicator light is on (but not blinking), it means that the printer is out of paper or
almost out of paper or the printer covers are open. When this light blinking, there is an
error. (See "ERROR LED blinking pattern" (2.2.2) in Chapter 2.) If you see this light
blinking, turn off the printer for a few seconds and then turn it back on. If the light is still
blinking, call your supervisor or a service person.
- PAPER OUT LED (Red Color)
When this indicator light is on, it means that the paper near end. Replace the new paper
roll. When ERROR and PAPER OUT indicator lights are on it means paper end. Install the
paper roll.(See "Installing paper roll"(2.1.4)in Chapter 2.)
- FEED button
Use this button to feed paper or to start self test and for hexadecimal dump mode.
(See the instructions "Self test" (2.2.3) in this chapter for self test.)
(See the instructions "Hexadecimal dump" (2.2.4) in Chapter 2 for hexadecimal dump
mode.)
Rev. 2.00
- 14 -
SRP-275
2-2-2 ERROR LED blinking pattern
The printer stops all printer operations for the selected paper section, goes off line, and the ERROR LED
blinks when an error is detected.
• Errors that automatically recover
Error
Description
Rear cover open error
(When recoverable
Error is selected)(*1)
The rear cover is opened
when printing
Print head
temperature error(*2)
The temperature of the
print head is extremely
high.
ERROR LED blinking pattern
200ms
Recovery
Recovers automatically
when the rear cover is
closed.
Recovers automatically
when the print head
cools.
NOTES
(*1) These conditions are selected by MSW8-5, 8-8. When MSW8-5 (mapping of the cover open status)
is off, the error hasn’t occurred but there is a “paper end error” instead. If MSW8-8 is off, this error
is handled as an automatically recoverable error.
(*2) Print head temperature error is not abnormal.
• Recoverable errors
When a recoverable error occurs, after the cause of the error is removed, the printer can recover from the
error by receiving an error recovery command without turning off the power.
Error
Description
ERROR LED blinking pattern
Recovery
Rear cover open error
(*1)
The rear cover is opened
when printing.
Auto cutter error
(Type C only)
Home position
detection error (This
is “Mechanical error”)
The auto cutter does not
work correctly.
The home position
cannot be detected due
to a paper jam.
200ms
Recovers automatically
when the rear cover is
closed.
Recovers by error
recovery command.
Recovers by error
recovery command.
NOTES
(*1) These conditions are selected by MSW8-5, 8-8. When MSW8-5 (mapping of the cover open status)
is off, the error does not occur and a “paper end error” occurs instead. If MSW8-8 is on, this error is
handled as a recoverable error.
• Errors that are impossible to recover
Error
Description
R/W error in memory
or gate array
High voltage error
Low voltage error
CPU execution error
Print head temperature
detection circuit error.
ERROR LED blinking pattern
After R/W checking, the
printer does not work
correctly.
Writing to, reading out, or
erasing the NV memory for
image scanning results
does not work correctly.
The power supply voltage
is extremely high.
The power supply voltage
is extremely low.
The CPU executes an
incorrect address or I/F
board is not connected.
There is an abnormality is
the print head temperature.
200ms
Recovery
Recovers automatically
when the rear cover is
closed.
Impossible to recover.
Impossible to recover.
Impossible to recover.
Impossible to recover.
NOTES
If you see this light blinking, turn off the printer for a few seconds and then turn it back on.
If the light is still blinking, call your supervisor or a service person.
Rev. 2.00
- 15 -
SRP-275
2-2-3 Hexadecimal Dumping
This feature allows experienced users to see exactly what data is coming to the printer.
This can be useful in finding software problems. When you turn on the hexadecimal dump function, the
printer prints all commands and other data in hexadecimal format along with a guide section to help you find
specific commands.
• To use the hexadecimal dump feature, follow these steps:
1) After you make sure that the printer is off, open the rear cover of the printer.
2) Hold down the FEED button while you turn on the printer.
3) Close the rear cover.
4) Run any software program that sends data to the printer. The printer prints "Hexadecimal dump" and then
all the codes are received in a two column format. The first column contains the hexadecimal codes and
the second column gives the ASCII characters that correspond to the codes.
Hexadecimal Dump
To terminate hexadecimal dump
Press FEED button three times
1B 21 00 1B 26 02 40 40 . ! . . & . @ @
1B 25 01 1B 63 34 00 1B . % . . c 4 . .
41 42 43 44 45 46 47 48 A B C D E F G H
<Online Hex Dump Completed>
(A period(.) is printed for each code that has no ASCII equivalent.)
5) When the printing finishes, turn off the printer.
2-2-3 The self Test Mode
The self test let you know if your printer is operating properly. It checks the printing quality, ROM version, DIP
Switch settings, memory switch settings and statistic data.
The test is independent of any other equipment or software, so it is a good idea to run it when you first set up
the printer or if you have any trouble. If the self test works correctly, the problem is in the other equipment or
the software, not the printer.
• Running the self test
1) Make sure the printer is turned off and the printer cover is closed properly.
2) While holding down the FEED button, turn on the printer and continue to hold until the paper begins to
feed. The self test prints the printer DIP Switch settings and memory switch settings. And cuts the paper
and pauses. (The power light blinks.)
3) Press the FEED button to continue printing the rolling ASCII pattern.
4) The self test mode terminates after printing the rolling ASCII pattern automatically.
Rev. 2.00
- 16 -
SRP-275
• Example of Self test sheet
!”#$%&’()*+,-./0123456789:;<=>?@ABCDEFGH
”#$%&’()*+,-./0123456789:;<=>?@ABCDEFGHI
#$%&’()*+,-./0123456789:;<=>?@ABCDEFGHIJ
$%&’()*+,-./0123456789:;<=>?@ABCDEFGHIJK
%&’()*+,-./0123456789:;<=>?@ABCDEFGHIJKL
&’()*+,-./0123456789:;<=>?@ABCDEFGHIJKLM
’()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMN
()*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNO
)*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOP
*+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQ
+,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQR
,-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRS
-./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRST
./0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTU
/0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUV
0123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVW
123456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWX
23456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXY
3456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ
456789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[
56789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\
6789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]
789:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^
89:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_
9:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`
:;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`a
;<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`ab
<=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abc
=>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcd
>?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcde
?@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdef
@ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefg
ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefgh
BCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghi
CDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghij
DEFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijk
EFGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijkl
FGHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklm
GHIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmn
HIJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmno
IJKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnop
JKLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopq
KLMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqr
LMNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrs
MNOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrst
NOPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstu
OPQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuv
PQRSTUVWXYZ[\]^_`abcdefghijklmnopqrstuvw
SELF TEST
<SRP-275 VER. 1.0>
DIP Switch setup status
Interpreter (DIP1_1,2):
AutoCut
(DIP1 _ 3):
BusyCondition(DIP1 _ 4):
Memory S/W (DIP1 _ 5):
Logo Print (DIP1 _ 6):
Near_end
(DIP1 _ 7):
Print Column (DIP1 _ 8):
AutoLineFeed (DIP2 _ 1):
Interface
(Parallel):
Epson
Enabled
Off.L/BF
Off
Off
Enabled
40 / 33
Disabled
IEEE1284
Paper roll width : 76mm
DIP S/W 1
1 2 3 4 5 6 7 8
▓
▓
ON
OFF ▓ ▓
▓ ▓ ▓
▓
DIP S/W 2
1 2 3 4 5 6 7 8
ON
OFF
▓ ▓ ▓ ▓ ▓ ▓ ▓ ▓
Memory Switch setup status
Memory S/W 1 (M1_1-3):
Code Page
(M1_4-8):
Memory S/W 2 (M2_1-4):
Cover Open (M2 _ 5):
Memory S/W 2 (M2 _ 6):
Busy Release (M2 _ 7):
ErrorRecovery(M2 _ 8):
Reserved
PC437
Reserved
Paper Out
Reserved
640 bytes
Automatic
Memory S/W 1
1 2 3 4 5 6 7 8
ON
OFF ▓ ▓ ▓ ▓ ▓ ▓ ▓ ▓
Memory S/W 2
*** Completed ***
1 2 3 4 5 6 7 8
ON
OFF
▓ ▓ ▓ ▓ ▓ ▓ ▓ ▓
<Press Feed Button ... >
Rev. 2.00
- 17 -
SRP-275
2-3 Setting the Dip Switches
Although the factory settings are best for almost all users, if you have special requirements, you can change
the DIP Switch. Your printer has two sets of DIP Switches. The functions of the switches are shown in the
following table.
2-3-1 DIP Switch setting for Epson(ESC/POS) mode
• DIP Switch 1
Switch
1-1
1-2
1-3
Function
ON
Emulation Selection (*1)
OFF
Refer to the following table
Auto cutter
Enable
1-4
BUSY condition
Receive buffer full
1-5
1-6
1-7
1-8
Serial interface selection
Print NV bit image #1 after cutting
Near end switch
Print column
Memory Switch
Enable
Enable
42/35
Default
OFF
Disable
Receive buffer full
or Offline
DIP Switch
Disable
Disable
40/33
OFF
OFF
OFF
OFF
OFF
OFF
Default
OFF
• DIP Switch 2 (RS232C serial interface model)
Switch
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
Function
ON
Data receive error
Hand shaking
Word length
Parity check
Parity selection
Ignore
Print “?”
Reserved
XON/XOFF
7 bits
Enable
EVEN
Baud rate selection (*2)
DTR/DSR
8 bits
Disable
ODD
Refer to the following table
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
• DIP Switch 2 (Parallel interface model)
Switch
Function
ON
OFF
Default
2-1
Auto Line Feed
Enable
Disable
OFF
2-2~8
Undefined
OFF
NOTES
(*1) Emulation Selection (DSW 1-1 and 1-2)
Emulation
1-1
1-2
EPSON
STAR
CITIZEN
EPSON-KP
OFF
OFF
ON
ON
OFF
ON
OFF
ON
- EPSON-KP(EPSON Kitchen Printer mode) : A alarm is generated by printer after auto cutting and in paper end error.
(*2) Baud rate selection (Transmission speed)
Transmission
2400 baud
4800 baud
9600 baud
19200 baud
Rev. 2.00
2-7
ON
OFF
OFF
ON
2-8
ON
ON
OFF
OFF
- 18 -
SRP-275
2-3-2 DIP Switch setting for Citizen(iDP 3550) mode
• DIP Switch 1
Switch
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
Function
ON
OFF
Default
Emulation Selection (*1)
Refer to the following table
OFF
Auto cutter
Enable
CBM2 mode
(iDP3530 system)
OFF
CBM command
Disable
CBM1 mode
(iDP3540 system)
OFF
International characters (*2)
Refer to the following table
ON
CR mode
CR
OFF
CR+LF
• DIP Switch 2 (RS232C serial interface model)
Switch
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
Function
Word length
Parity check
Parity selection
Hand shaking
ON
8 bits
Disable
ODD
DTR/DSR
Baud rate selection (*3)
OFF
7 bits
Enable
EVEN
XON/XOFF
Refer to the following table
Near end switch
Mechanism type
Enable
Graphic
Disable
Character
Default
ON
ON
ON
ON
OFF
OFF
OFF
NOTES
(*1) Emulation Selection (DSW 1-1 and 1-2)
Emulation
1-1
1-2
EPSON
STAR
CITIZEN
EPSON-KP
OFF
OFF
ON
ON
OFF
ON
OFF
ON
- EPSON-KP(EPSON Kitchen Printer mode) : A alarm is generated by printer after auto cutting and in paper end error.
(*2) International Character Selection
No.
Country
U.S.A.
France
Germany
U.K.
Denmark
Sweden
Italy
Windows Code
DSW 1-5
DSW 1-6
DSW 1-7
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
(*3) Baud rate selection (Transmission speed)
Transmission
2400 baud
4800 baud
9600 baud
19200 baud
Rev. 2.00
2-5
ON
OFF
OFF
ON
2-6
ON
ON
OFF
OFF
- 19 -
Code page
Page 0 (PC437 : U.S.A.)
Page 2 (PC850 : Multilingual)
Page 5 (PC865 : Nordic)
Page 2 (PC850 : Multilingual)
Windows Code
SRP-275
2-3-3 DIP Switch setting for Star(SP500) mode
• DIP Switch 1
Switch
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
Function
ON
Emulation Selection (*1)
OFF
Refer to the following table
Auto cutter
Black/Red Printing
Enable
Enable
Disable
Disable
Reserved
Default
OFF
OFF
OFF
OFF
• DIP Switch 2 (RS232C serial interface model)
Switch
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
Function
ON
OFF
Reserved
Hand shaking
Word length
Parity check
Parity selection
OFF
XON/XOFF
7 bits
Enable
EVEN
Baud rate selection (*2)
Default
DTR/DSR
8 bits
Disable
ODD
Refer to the following table
OFF
OFF
OFF
OFF
OFF
OFF
NOTES
(*1) Emulation Selection (DSW 1-1 and 1-2)
Emulation
1-1
1-2
EPSON
STAR
CITIZEN
EPSON-KP
OFF
OFF
ON
ON
OFF
ON
OFF
ON
- EPSON-KP(EPSON Kitchen Printer mode) : A alarm is generated by printer after auto cutting and in paper end error.
(*2) Baud rate selection (Transmission speed)
Transmission
2400 baud
4800 baud
9600 baud
19200 baud
2-7
ON
OFF
OFF
ON
2-8
ON
ON
OFF
OFF
NOTICE
Change in DIP Switch settings are recognized only when the printer power is turned on or when the
printer is reset by using the interface. If the DIP Switch setting is changed after the printer power is
turned on, the change does not take effect until the printer is turned on again or is reset.
Rev. 2.00
- 20 -
SRP-275
2-3-4 Changing the DIP Switch setting
If you need to change settings, follow the steps below to make your changes.
CAUTION
Turn off the printer before removing the DIP Switch cover to prevent an electric short, which can damage
the printer.
1) Make sure the printer is turned off.
2) Remove the screw from the DIP Switch cover.
Then take off the DIP Switch cover, which is shown in the illustration below.
3) Set the switches using a pointed tool, such as tweezers or a small.
4) Replace the DIP Switch cover. Then secure it with the screw.
NOTES
The new settings take effect when you turn on the printer.
Rev. 2.00
- 21 -
SRP-275
2-4 Setting the Memory Switches
2-4-1 Memory Switch setting for Epson(ESC/POS) mode
This printer has “Memory Switch” set which is software switches. Memory Switch set has “MSW 2”, “MSW 8”,
“Customize value”, “Serial communication condition”. “Memory Switch setting utility” can change the Memory
Switch set to ON or OFF as shown in the table below (default: all OFF):
NOTES
The Memory Switch is available to be changed by three methods:
- Memory Switch setting utility
- Memory Switch setup mode (there are limitations on what can be changed)
- Control from ESC/POS command
- Some Memory Switch settings can be changed by the “Memory Switch setting mode”. See “Procedure of
Memory Switch setting”.
Settings of the Memory Switch are stored in the NV memory; therefore, even if the printer is turned off, the
settings are maintained. When you replace a SRP-270 with a SRP-275, you should adjust the MSW 8-5 to
OFF.
• Memory Switch 2
Switch
Function
1
Reserved
2
Reserved
3
Reserved for Chinese selection
4~8
Code page selection (*1)
On
Off
Fixed to Off
Fixed to Off
Fixed to Off
Refer to the following table
NOTES
Desired code page can be selected using Memory Switch 2-4~8 by setting as following.
(*1) Code page selection
MSW 2-8
MSW 2-7
MSW 2-6
MSW 2-5
MSW 2-4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
0
1
(*2) Only Font B available.
Rev. 2.00
- 22 -
Character Table
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
0 (PC437 : U.S.A.)
1 (Katakana)
2 (PC850 : Multilingual)
3 (PC860 : Portuguese)
4 (PC863 : Canadian-French)
5 (PC865 : Nordic)
16 (WPC1252 : Latin1)
17 (PC866 : Russian)
18 (PC852 : Latin2)
19 (PC858 : Euro)
21 (PC862 : Israel)
22 (PC864 : Arabic)
23 (Thai character code 42)
24 (WPC1253 : Greek)
25 (WPC1254 : Turkish)
26 (WPC1257 : Baltic)
27 (Farsi) (*2)
28 (WPC1251 : Russian) (*2)
29 (PC737 : Greek) (*2)
30 (PC775 : Baltic) (*2)
31 (Thai character code 14)
32 (Old Code : Israel)
33 (WPC1255 : Israel)
34 (Thai character code 11)
35 (Thai character code 18)
37 (PC857 : Turkish)
38 (PC928 : Greek)
SRP-275
• Memory Switch 8
Switch
1
2
3
4
5
6
7
8
Function
Upside down
Font Selection
Selection Paper End Buzzer
Reserved
Selection of the cover open status
Buffer Size
Receive buffer full release
On
Off
Off
Font A
On
Fixed to Off
Cover open
Paper end
40 bytes
8 Kbytes
Remaining 522 bytes
Remaining 640 bytes
Errors that can
Errors that
possibly recover
automatically recover
On
Font B
Off
Printer (Cover open during operation)
NOTES
MSW 8-5:
When Off is selected, a bit of the “paper end sensor” in each status that is transmitted from the printer is
changed every time the rear cover is open or closed. When On is selected, a bit of the “rear cover open /
close" in each status that is transmitted from the printer is changed every time the rear cover is open or
closed. When you replace a SRP-270 with a SRP-275, you should adjust the MSW 8-5 to Off.
MSW 8-8:
When Off is selected, a bit of the “automatic recoverable error” in each status that is transmitted from
the printer is changed every time the rear cover is open. When On is selected, a bit of the “mechanical
error” in each status that is transmitted from the printer is changed every time the rear cover is open.
The setting of MSW 8-5 and 8-8 can be set by “Memory Switch setup mode”.
• Customize value
Function
Paper roll width
Selectable value
57.5 mm / 69.5 mm / 76 mm (default value)
NOTES
These setting can be set by “Memory Switch setup mode.”
• Serial communication
Function
baud rate
Parity
Handshake
Data length
Selectable value
2400 bps
4800 bps
9600 bps
19200 bps
None
Odd
Even
DSR/DTR
XON/XOFF
7 bit
8 bit
NOTES
There are two methods, DIP Switch and Memory Switch, to adjust the serial communication conditions.
DIP Switch 1-5 selects which is effective, DIP Switch or Memory Switch.
To enable the “Serial communication“ setting, you have to adjust the “Serial interface selection“ function
of DIP Switch 1-5 to “Memory Switch”.
These settings can be set by “Memory Switch setup mode”.
Rev. 2.00
- 23 -
SRP-275
• Memory Switch Setup Mode
The following items are specified in the Memory Switch setup mode:
Basic Serial communication condition (Serial communication)
- Transmission speed
- Parity
- Handshaking
- Data length
Receive buffer full release condition (MSW 8-7)
Paper roll width (Customize value)
Cover open status (MSW 8-5)
NOTES
All new settings will be lost if the power supply is turned off in the Memory Switch setup mode. Be sure to
follow the proper procedure, and turn the power off at the correct time.
Use the following procedure to start the Memory Switch setup mode.
1) Open the paper roll cover.
2) Turn the power on while pressing the paper FEED button.
3) Press the FEED button twice while POWER, ERROR, and PAPER OUT LEDs are lit.
4) Close the cover. The printer prints the enabled settings of the Memory Switches and instructions.
5) Follow the instructions to process the switch setup.
NOTES
In the Memory Switch setup, the power LED may be flashing.
• Example of Memory Switch setup sheet
Memory S/W Setup
You can choose desired item using
YES or NO as following
Paper width
Current paper width: 76.0 mm
YES: Keep pressing FEED button
Until printing starts
NO : Press & release it swiftly
Do you want to change
paper width?
Serial interface setting
Do you want to change
Serial interface condition?
Cover open status
Current status: Paper out
Do you want to change
cover open status?
Buffer full release condition
Current condition: 640 bytes left
Do you want to change
Buffer full release condition?
Rev. 2.00
- 24 -
SRP-275
• Procedure of Memory Switch setting
Entering Memory Switch Setting Mode
NO
① Resetting Basic Serial Interface?
YES
Baud rate
Current
setting:
9600 bps
NO
19200bp
NO
NO
YES
NO
Handshake
Current
setting:
DSR/DTR
NO
Parity
Current
setting:
Non
YES
XON/XOFF
NO
YES
Even
YES
7 bits
NO
YES
4800bps
YES
Odd
NO
NO
2400bps
YES
NO
NO
YES
Data bit
Current
setting:
8 bits
YES
YES
NO
② Resetting Buffer full release
condition?
Current setting: 640 bytes
YES
NO
NO
YES
YES
Finishing Memory
S/W Setting Mode?
522 bytes
NO
③ Resetting Paper width?
Current setting: 76 mm
YES
69.5 mm
NO
Finishing Memory
S/W Setting Mode?
YES
Finishing Memory
S/W Setting Mode?
YES
NO
NO
57mm
YES
YES
④ Resetting Cover open status?
Current setting: Paper out
NO
YES
Cover open
Rev. 2.00
- 25 -
YES
Memory S/W Setting
Completed
SRP-275
2-4-2 Memory Switch setting for Star mode
• Settings
Memory Switches are from MSW 0 to MSW 8. They are stored in non-volatile memory (flash memory). To
change the settings, send the following commands from the host.
[Name]
Set Memory Switch
[Code]
ASCII
ESC
GS
#
Hexadecimal
1B
1D
23
m N n1 n2 n3 n4 0A 00
Decimal
27
29
35
m N n1 n2 n3 n4 10 0
m N n1 n2 n3 n4 LF NUL
[Defined Region] m = "W", "T", ",", "+", "-", "@"
"0" ≤ N,n1,n2,n3,n4 ≤ "9",
"A" ≤ N,n1,n2,n3,n4 ≤ "F"
[Function]
Sends command to write after defining Memory Switch using the definition command
specified by the following classes to set the Memory Switch. The printer is automatically
reset after writing the setting defined by that command to the non-volatile memory.
Do not turn off the power to the printer while sending commands to the non volatile
memory. Doing so will destroy the Memory Switch setting. It is also possible for all Memory
Switch settings to become offset to their initial, default settings.
Consider the life of the non-volatile memory and avoid over-use of this command.
Function
Data Definition (Data Specification)
Data definition (set specified bit)
Data definition (clear specified bit)
Data Definition (clear all data)
Definition data write and reset
Definition data write and reset and test print
Class
Definition
Definition
Definition
Definition
Write
Write
m
","
"+"
"-"
"@"
"W"
"T"
N
N
N
N
Fixed at "0"
Fixed at "0"
Fixed at "0"
n1 n2 n3 n4
n1 n2 n3 n4
n1 n2 n3 n4
n1 n2 n3 n4
Fixed at "0000"
Fixed at "0000"
Fixed at "0000"
(Ex) Memory Switch 1-8 = 0; Memory Switch 2-7 = 1: Memory Switch 2-A =1 for a test print:
PRINT #1, CHR$(&H1B);CHR$(&H1D);CHR$(&H23);CHR$(&H2D);CHR$(&H31); ' <ESC><GS> # - 1
PRINT #1, CHR$(&H30);CHR$(&H31);CHR$(&H30);CHR$(&H30);CHR$(&H0A);CHR$(0); ' 0100 <LF><NUL>
PRINT #1, CHR$(&H1B);CHR$(&H1D);CHR$(&H23);CHR$(&H2B);CHR$(&H32); ' <ESC><GS> # + 2
PRINT #1, CHR$(&H30);CHR$(&H34);CHR$(&H38);CHR$(&H30);CHR$(&H0A);CHR$(0); ' 0480 <LF><NUL>
PRINT #1, CHR$(&H1B);CHR$(&H1D);CHR$(&H23);CHR$(&H54);CHR$(&H30); ' <ESC><GS> # T 0
PRINT #1, CHR$(&H30);CHR$(&H30);CHR$(&H30);CHR$(&H30);CHR$(&H0A);CHR$(&H0); ' 0000 <LF><NUL>
Rev. 2.00
- 26 -
SRP-275
• Default Settings
The default settings for Memory Switch 0 to Memory Switch 8 are shown below.
Settings vary for single byte character countries (standard specifications (SBCS)) and for double-byte
character countries (Chinese character specifications (DBCS)).
- Standard Specifications (SBCS)
Memory Switch Number
MSW 0
MSW 1
MSW 2
MSW 3
MSW 4
MSW 5
MSW 6
MSW 7
MSW 8
Ex-factory Settings (n1, n2, n3, n4)
"0000"
"0000"
"0000"
"0000"
"0000"
"0000"
"0000"
"0000"
"0000"
- Chinese character specifications (DBCS) (For China)
Memory Switch Number
MSW 0
MSW 1
MSW 2
MSW 3
MSW 4
MSW 5
MSW 6
MSW 7
MSW 8
Rev. 2.00
Ex-factory Settings (n1, n2, n3, n4)
"0010"
"0000"
"0000"
"0000"
"0000"
"0000"
"0000"
"0000"
"0000"
- 27 -
SRP-275
• Function
- Memory Switch 0
Bit
F~C
B~A
9~5
4
3~2
1~0
Function
Reserved
Red and Black
(inverted black and white) Commands (*3)
Reserved
0
1
Refer to the following table
SBCS
DBCS
(Single Byte countries) (Double Byte countries)
Refer to the following table
Country Specifications (*1)
<FF> Command (*2)
Reserved
NOTES
(*1) Country Specifications
Country
Overseas
MSW 0-4 = 0
Standard Specifications
MSW 0-4 = 1
Chinese Characters
(*2) <FF> Command Function Selection
MSW 0-3 MSW 0-2
Auto cutter model
0
0
0
1
1
0
1
1
<FF> Command Function
<FF> Command Function
Tear Bar Model (SRP-275A type)
Executes a form feed.
Executes a form feed.
After paper fed to cutting position
Paper fed to the tear-bar position
Executes partial cut (*3)
Executes a form feed.
Executes a form feed.
After paper fed to cutting position
Paper fed to the tear-bar position
Executes partial cut (*3)
(*3) Red and Black (inverted black and white) Commands
MSW 0-B
0
0
1
1
MSW 0-A
0
1
0
1
<ESC> 4 / <ESC> 5 Command Functions
White/black inverted printing (1 Pass)
<Option 1> White/black inversion (7×9 font print) + enhancing (2 passes)
<Option 2> Upper line + Underline + enhancing (2 passes)
<Option 3> Upper line + Underline + double tall expanded + enhancing (4 passes)
This setting functions to specify adornments when the subsequent red (white/black inversion) print
command is set. It is a substitute function for the conventional red/black (white/black inversion) printing.
<ESC> “4”: Red (white/black inversion) printing
<ESC> “5”: Red (white/black inversion) printing cancelled.
When using <ESC> 5 to cancel adornments, it returns to the previously set adornments. (Adornments
such as underline, upper line, double-tall expanded and enhancing are cancelled if there is no command
to set them (for example the <ESC> “-” 1 specification for underlines).
This setting is enabled only for ANK characters and block characters. It is disabled for IBM block
characters and Chinese characters composed of 12 dot vertical characters (IBM block characters and
Chinese characters do not have adornment with this command).
- Precautions for selecting Option 1.
1) Prints white/black inverted characters using 5 × 9 fonts regardless of the current font size setting.
2) Inserts a one dot string of black printing to the head of the white/black inverted characters.
3) Printing data created on a conventional red/black printer, using 1 and 2 above, there are cases in
which the printing position will shift to the right and a line of printable characters reduced.
(For example, to write 42 digits of red print data using conventional a 7 × 9 font, there is a line feed at
the 35th digit, and the remaining 7 digits are printed on the next line.)
4) Download defined characters defined with 5 × 9 fonts are printed regardless of the current font setting
(7×9/5×9).
5) MSW 3-6 must not be set to 1 (ANK character count = many). (This will cause a while line to appear
between characters.)
- Precautions for selecting Option 2 and Option 3.
1) Do not apply an upper line or an underline to characters when rotating 90 or 270 degrees.
Rev. 2.00
- 28 -
SRP-275
- Memory Switch 1
Bit
F
E~5
4
3~0
Function
Reserved
0
Zero style
International Characters (*1)
1
Normal
Slash zero
Refer to the following table
NOTES
(*1) International Characters Default Value Settings
MSW1-3
MSW1-2
MSW1-1
MSW1-0
0
0
0
0
0
0
0
1
0
0
1
0
0
0
1
1
0
1
0
0
0
1
0
1
0
1
1
0
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
International Characters
U.S.A
France
Germany
U.K.
Denmark1
Sweden
Italy
Spain 1
Japan
Norway
Denmark2
- Memory Switch 2
Bit
F
E
D~C
B
A
9~4
3
2
1~0
Function
Reserved
How to Recover to Print Ready after
Inserting Paper
Reserved
Printing Region Width (*1)
Paper Width Selection (*1)
Contextual Auto-cut Function (*2)
0
1
Press FEED.
Auto-recovery
Refer to the following table
Refer to the following table
Disabled
Near end switch Function (*3)
Enabled
Refer to the following table
NOTES
(*1) Print Region Width (MSW 2-B)/Paper Width (MSW 2-A) Selection
MSW 2-B
0
0
1
1
MSW 2-A
0
1
0
1
Printing Region Width
400 half dots
300 half dots
385 half dots
297 half dots
Paper Width
76mm
57.5mm
76mm
57.5mm
(*2) Contextual Auto-cut Function
This function auto-cuts paper when a paper feed command that feeds continuously over 7/6 inch.
Hosts that cannot send an escape sequence, such as <ESC> “d” 0 can cut paper if a 1/6 inch line feed
code <LF> is sent seven times.
(*3) Near end switch Function
When an optional near end switch is mounted, settings should abide by those shown in the table below.
MSW 2-1
0
0
MSW 2-0
0
1
1
0
1
1
Rev. 2.00
Near end switch Function
Disabled
Disabled
Reflects the near end switch state to the status.
Printing does not stop for near end, and the printer does not go offline.
Reflects the near end switch state to the status.
Printing does stop for near end, and the printer goes offline.
- 29 -
SRP-275
- Memory Switch 3
Bit
F~D
C~8
7~2
1~0
Function
0
1
Character Table (*2)
Refer to the following table
<CR> Command Functions (*1)
Refer to the following table
NOTES
(*1) <CR> Command Functions
MSW3-1
0
0
1
1
MSW3-0 <CR>
0 Ignored
1 Ignored
0
1
Functions
Prints and performs a line feed (same as <LF>.)
Prints (No line feed)
(*2) Character Table Settings
These settings are enabled only on standard specification printers.
MSW3-C
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
0
1
1
1
1
1
MSW3-B
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
MSW3-A
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
MSW3-9
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
MSW3-8
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
(*3) Only Font B available.
Rev. 2.00
- 30 -
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Character Table
0 (PC437 : U.S.A.)
1 (Katakana)
2 (PC850 : Multilingual)
3 (PC860 : Portuguese)
4 (PC863 : Canadian-French)
5 (PC865 : Nordic)
16 (WPC1252 : Latin1)
17 (PC866 : Russian)
18 (PC852 : Latin2)
19 (PC858 : Euro)
21 (PC862 : Israel)
22 (PC864 : Arabic)
23 (Thai character code 42)
24 (WPC1253 : Greek)
25 (WPC1254 : Turkish)
26 (WPC1257 : Baltic)
27 (Farsi) (*3)
28 (WPC1251 : Russian) (*3)
29 (PC737 : Greek) (*3)
30 (PC775 : Baltic) (*3)
31 (Thai character code 16)
32 (OldCode : Israel)
33 (WPC1255 : Israel)
34 (Thai character code 11)
35 (Thai character code 18)
SRP-275
- Memory Switch 4
Bit
F~9
8
Function
0
Automatic Status Function
Disabled
ESC RS a n command function
Only Setting
Data reception error (serial)
Prints “?”
1
Enabled
7~4
3
2~1
0
Auto-status sent only
once
Ignored
- Memory Switch 5
Bit
F~0
Function
Reserved
0
1
Function
0
1
- Memory Switch 6
Bit
F~A
9
Reception Buffer or
Offline
BUSY Condition
Reception Buffer Full
8~0
- Memory Switch 7
Bit
F~0
Rev. 2.00
Function
Reserved
0
- 31 -
1
SRP-275
3. Product Specifications
3-1 Appearance
3-1-1 Printer Dimensions (mm)
• SRP-275A Type
• SRP-275C Type
(Approx. wt.: 2.4 kg, Shipping. Wt : 3.9 kg)
(Approx. wt.: 2.5 kg, Shipping. Wt : 4.0 kg)
157
157
239
239
160
160
3-1-2 AC Adapter Dimensions (mm)
36
115
56
Rev. 2.00
- 32 -
SRP-275
3-1-3 Feature Locations
• SRP-275A Type
• SRP-275C Type
4
4
5
3a
5
3b
2
2
1
1
6
6
RS-232
9a
USB
PARALLEL
10
9b
10
9c
10
7
8
Rev. 2.00
1. Cover base
2. Cover middle
3a. Cover front-A
3b. Cover front
4. Cover rear
5. Button open
6. Power switch
7. Frame-cover DIP
8. DC power jack
9a. Serial I/F connector (RS-232C)
9b. Parallel I/F connenctor (IEEE1284)
9c. USB I/F connector
10. Drawer kick-out connector
- 33 -
SRP-275
3-2 General Specifications
Item
Description
Remark
• SRP-275 : RS-232 Serial communication
Product
• SRP-275P : IEEE 1284 Parallel communication
• SRP-275U : USB communication
Processor
Memory
• SAMSUNG S3C4640 (32bit)
• Flash : 8Mbits (M29F800DB)
• DRAM : 16Mbits
• Flow control
① DTR/DSR (H/W flow control)
Serial interface
(RS-232C)
② XON/XOFF (S/W flow control)
• Baud rate : 2400/4800/9600/19200
• Receive buffer : 8Kbytes
• Connector : DB25P female (I/F PBA side)
• Mode
Parallel interface
① Forward mode : Compatibility mode
(IEEE 1284)
② Reverse mode : Nibble / Byte mode
• Connector : Self-powered
• Transfer type : BULK
USB
• Speed : 12Mbps (Full-speed)
• Power : Self-Powered
Printer
Auto cutter
Power consumption
AC adaptor
Environment condition
Weight (kg)
Dimensions (mm)
Rev. 2.00
• Printing method : 9pins serial impact
• Printing speed : 5.1 lines/sec
• Type : Rotary
• Cutting method : 1 point partial cutting
• Approx. 36W
• Input : AC 100V~240V, 50Hz~60Hz
• Output : DC24V±5%, 1.5A
• Temperature : 0℃~40℃
• Humidity : 30%~80%
• Packing : Approx.3.9kg (A type) / 4kg (C type)
• Unpacking : Approx. 2.4kg (A type) / 2.5kg (C type)
• A / C type : 160×239×157
- 34 -
The flow control,
Baud rate, Stop bit
and Parity are
determined by DIP
Switch position.
SRP-275
3-3 Reference information
3-3-1 Printer Mechanism Specification
Item
Description
Model
SMP-715
Printer method
Serial impact type
Printer direction
Bi-directional with logic seeking
Printing speed
5.1 lines/sec (9ⅹ7 font 40 columns)
Printing resolution
160(W)ⅹ144(L) DPI
Paper feeding
Performed by step motor
Paper
Paper roll : 76±0.5(W)ⅹMax.Ø80 mm
Supply voltage
Remark
Samsung
• 24V±10% : Step motor, head
• 5V±10% : Home position sensor, motor driver IC
30pin (Dot head, sensor signal, motor control and power input)
Connector
LIFE : Approx. 20 million print lines
Reliability
Approx. 10 million print lines
Head life
Approx. 300 million dots / wire
Weight
Approx. 1.1kg (Excluding ribbon cassette, auto cutter)
3-3-2 Printing Specification
Item
Description
Printing method
Serial impart dot
Head wire configuration
9 pin serial type (*1)
Dot pitch
0.352mm (1/72”)
Dot wire diameter
0.3mm (0.01”)
Printing direction
Bidirectional with logic seeking
Line feed
4.233mm (1/6”) : default setting
Paper feed method
Friction feed
Paper feed speed
Characters per line
Characters per inch
Samsung
Approximately 6.2 inches/second
during continuous paper feeding
Refer to the following table (*2)
Total dot count
• 7×9 font : 400 half-dot positions per line
(horizontal direction)
• 9×9 font : 400 half-dot positions per line
Print speed
Rev. 2.00
Remark
• 40 columns, 16cpi : Approximately 5.1 lines/second
• 16 columns, 16cpi : Approximately 8.6 lines/second
- 35 -
SRP-275
NOTES
If the print duty ratio is too high, the operation of the print head is stopped by the duty limit. In such
circumstances, the print speeds shown above cannot be guaranteed.
- cpi=characters per inch
(*1) Dot configuration
0.352mm
(0.014")
0.3mm (0.012")
(wire diameter)
0.317mm (0.012")
(*2) Character dimensions, characters per inch, characters per line
Character structure
Horizontal×Vertical
Character
structure
Character Set
ANK
7×9
Graphics
ANK
9×9
Graphics
ANK
7×9
Graphics
ANK
9×9
Graphics
Character
dimensions
W×H
1.2×3.1mm
(.047×.122")
1.7×3.1mm
(.070×.122")
1.6×3.1mm
(.063×.122")
2.0×3.1mm
(.079×.122")
1.2×3.1mm
(.079×.122")
1.6×3.1mm
(.063×.122")
1.6×3.1mm
(.063×.122")
1.9×3.1mm
(.075×.122")
Dot spacing
between
characters
Characters
per line
(cpi)
Characters
per inch
(cpi)
3 half dots
40
16
0
40
16
3 half dots
33
13.3
0
33
13.3
2 half dots
42
17.8
0
42
17.8
2 half dots
35
14.5
0
35
14.5
NOTES
The default font is 7×9; the dot spacing between characters is either 3 half dots or 2 half dots, depending
on programming.
Rev. 2.00
- 36 -
SRP-275
3-3-3 Character Specification
Item
Description
Dot interval
H
0.3175 mm
V
0.3528 mm
Font type
ASCII
Print font
Remark
Chinese
9ⅹ9
7ⅹ9
16ⅹ16
33
40
-
1.7ⅹ3.2
1.4ⅹ3.2
5.7ⅹ3.0
Column interval (mm)
2.13
1.59
3.19
Line interval
1/6"
1/6"
1/3"
Printing columns
Character size (mm) (*1)
• Alphanumeric characters : 95
Character sets
• International characters : 32
• Extended graphics : 128 x 20 pages
Character structure
• 7×9 with 400 half-dot positions per line
• 9×9 with 400 half-dot positions per line
NOTES
(*1) Character size 7×9 font example
1.59mm (0.062")
1.25mm (0.049")
0.352mm
(0.014")
2.41mm
(0.095")
3.12mm
(0.123")
0.159mm (0.006")
Rev. 2.00
- 37 -
SRP-275
3-3-4 Paper Specification
Item
Description
Paper type
Paper roll
• 76±0.5 mm (2.99±0.02”)
Paper roll width
• 69.5±0.5 mm (2.74±0.02”)
• 57.5±0.5mm (2.26±0.02”)
Paper roll diameter
Max. ø83 mm (3.27")
• Thickness : 1 sheet 0.06~0.085 mm (0.0024~0.0034")
Normal paper
• Weight : 52.3~64g/m2 (0.115~0.1411 lb)
Remark
NOTES
• Printing area
2.2mm (0.09")
(Partial cut)
Cutting position (Auto cutter, Type C)
4mm (0.16")
Cutting position (Manual cutter, Type A)
27.9mm (1.10")
27.5mm (1.08")
5.9mm (0.23")
63.34mm (2.49")
Maximum of 200 dots, 400 positions
6.76mm (0.27")
76mm (2.99")
3-3-5 Ribbon Cassette Specification
Item
Description
Model
RRC-275 B/R
Color
Black & Red
Size
13 mm (W)ⅹ6 mm (L)
• Black : 1.5 million characters (with continuous printing at 25℃ (77℉))
Life (*1)
• Red : 750,000 characters (with continuous printing at 25℃ (77℉))
Remark
NOTES
(*1) Ribbon life
Ribbon life is based on the following conditions:
Character font: 7×9 font (with descenders)
Print pattern: ASCII 96-character rolling pattern. See the example of self test sheet.
Malfunctions and other problems may arise if other than specified ribbon cassettes are used in the printer.
The Warranty may be void if other than specified ribbon cassettes are used. Contact your dealer or place
of purchase for more information about proper ribbon cassettes.
Rev. 2.00
- 38 -
SRP-275
3-3-6 Environment Conditions
Item
Description
• Operating : 0℃~50℃ (32℉~122℉). At 34℃(93℉) or higher,
Temperature
there are humidity restrictions; refer to the following figure. (*1)
• Storage : -10℃~50℃ (14℉~122℉)
• Shipping : -40℃~70℃ (-40℉~122℉), except paper and ribbon
• Operating : 10~90% RH (Non-condensing)
Relative humidity
• Storage : 10~90% RH (Non-condensing)
• Shipping : 5~90% RH (Non-condensing), except paper and ribbon
Vibration resistance
Impact resistance
• When packed
- Frequency: 5 to 55Hz
- Acceleration: 5G
- Sweep: 10 minutes (half cycle)
- Duration: 1 hour
- Direction: x, y and z
• When packed
- Package: SRP-275 standard package
- Height: 60cm (23.62")
- Directions: 1 corner, 3edges and 6 surfaces
• When unpacked
- Height: 5cm (1.97")
- Direction: Life on edge and release it (for all 4 edges)
NOTES
(*1) Operation temperature and humidity range
Rev. 2.00
- 39 -
Remark
SRP-275
3-3-7 Reliability
Item
Life
Head
Description
• Mechanism : Approx. 10 million lines
• Auto cutter : Approx. 1 million cuts
(End of life is defined as the point at which the printer
reaches the beginning of the Wear out Period.)
Approx. 300 million dots/wire
3-3-8 Certification
Item
Europe
North America
Safety standards
National
EMC Directive 89/336/EEC
Low voltage Directive 73/23/EEC
Description
CE marking, TUV/GS : EN60950-1; 2001
EMI : FCC Class A
UL / C-UL : UL60950-1
CB-scheme : IEC 60950-1: 2001
• EN55022 Class A : 1998+A1 : 2000
• EN55024 : 1998:+A1 : 2001
• EN61000-3-2 : 2000
• EN61000-3-3 : 1995+A1 : 2001
Safety : EN60950-1 : 2001
3-3-9 Printer(SMP715) pin Descriptions
Pin No.
Pin name
1
Thermistor
2
GND
3
Printer Head
4
Printer Head
5
Printer Head
6
Printer Head
7
VCC_24V
8
VCC_24V
9
VCC_24V
10
Printer Head
11
Printer Head
12
Printer Head
13
Printer Head
14
Printer Head
15
VCC_5V
16
H/S Output
17
Carriage Motor_PA
18
Carriage Motor_PAn
19
Carriage Motor_PB
20
Carriage Motor_PBn
21
Carriage Motor ON/OFF
22
Feed Moter A
23
Feed Moter An
24
Feed Moter B
25
Feed Moter Bn
26
VCC_24V
27
VCC_24V
28
SOL
29
GND
30
GND
Rev. 2.00
Remark
Remark
Description
Thermistor Output Value in Printer Head
Head #7
Head #1
Head #5
Head #3
The Voltage for Driving Print Heads
The Voltage for Driving Print Heads
The Voltage for Driving Print Heads
Head #2
Head #9
Head #4
Head #8
Head #6
Sensor and Motor Driving
Head home position check
Phase PA of the Carriage Motor
Phase PAn of the Carriage Motor
Phase PB of the Carriage Motor
Phase PBn of the Carriage Motor
Control Driving voltage or Holding Voltage Of Carriage Motor
Phase A of the Feed Motor
Phase An of the Feed Motor
Phase B of the Feed Motor
Phase Bn of the Feed Motor
The Voltage for Driving Motors
The Voltage for Driving Motors
Ribbon solenoid down
-
- 40 -
SRP-275
3-3-10 Printer Head Specification
Item
Model
Description
Remark
N09-15KS
Type : Ballistic type (Free fight)
Specification
Number of wire : 9pins
Dot pitch : 0.352 (1/72”)
Dot wire diameter : 0.3mm (0.01”)
Resistance : 18Ω ± 1.5Ω (at 20℃)
Solenoid coil
Inductance : 4.2mH ± 10% open circuit (at 1000Hz, 1VRMS)
Temperature rate : 155℃
Insulation resistance : 20MΩ with 500V/DC
Type : Constant voltage
Driver circuit
Voltage : 24VDC±5% (Normal) (At printer head)
Current : 1.3A
Pulse : 330μsec (Head on time)
Platen Gap : 0.40 ~ 0.50mm
Performance
Max. frequency : 1500Hz
Forms capability : Original + 2 copies
Temperature
Max. operating temp. : 90℃
Max. transient temp. : 110℃ ,For 5 minutes (25% duty)
3-3-11 Printer Head Thermistor Specification
Item
Description
Type
NTC, F-CHIP FF103J
Electronic
• Resistance R25: 10㏀ ± 5Ω (At 25℃)
Characteristics
• β Value : 3950K ± 2
Temperature strage
–30℃ ~ 125℃
Rx formula
Exp( -4.864010225 + 4344.5751119/T - 13183560.21/T^3)
Remark
T : Absolute temperature
3-3-12 PF(Paper Feed) Motor Specification
Item
Description
Model
PM42L-048-YKG3 (MINEBEA ELECTRONICS Co.Ltd)
Voltage
24VDC±10%
Current
500mA / Phase (Peak)
Resistance
7.4Ω ± 5% at 25℃
Step angle
7.5°
Pull out torque
800 PPS 590 g·cm
Rev. 2.00
- 41 -
Remark
NMB
SRP-275
3-3-13 HF(Head Feed) Motor Specification
Item
Description
Model
PM42S-048-SYM (MOATECH Co., Ltd)
Voltage
24VDC±10%
Current
640mA / Phase (Peak)
Resistance
10
Step angle
7.5°
Pull out torque
1300 PPS 324 g·cm
Remark
3-3-14 Auto Cutter Specification
Item
Description
Type
Rotary
Motor
DC Brush motor FK-130SH (Mabuchi Motor)
Voltage
24VDC ± 10%
Current
0.4A (mean) , 1.6A (peak)
Remark
3-3-15 Switch(Sensor) Specification
Item
Description
Paper end switch
Micro switch (MIC)
Paper near end switch
Micro switch (MIC)
Paper near end-W switch
Micro switch (MIC)
Cover open switch
Micro switch (MIC)
Remark
Wall mount
3-4 SMPS Specifications
3-4-1 SMPS (Switching Mode Power Supply) Specification
Item
Description
Input voltage
100VAC~240VAC
Input current
Max. 1.5A
Line regulation
+24V±1%
Load regulation
+24V±5%
Ripple noise
Peak 300mV
O.C.P
3.0A
(Over current protect)
3-4-2 SMPS Output Connector
Pin number
Signal name
1
+24VDC
2
GND
Rev. 2.00
Remark
- 42 -
SRP-275
3-5 Interface Specifications
3-5-1 RS-232C Serial Interface
3-5-1(a) Specification
Item
Description
Remark
Data transmission
Serial
Synchronization
Asynchronous
Handshaking
H/W : DTR / DSR
XON : ASC code 11
(Flow control)
S/W : XON / XOFF
XOFF : ASC code 13
Signal level
• Logic "1" (MARK) : -3V~-15V
• Logic "0" (SPACE) : +3V~+15V
Baud rate
19200 / 2400 / 4800 / 9600 bps
Data word length
7 bit / 8 bit
Parity
None / Even / Odd
Connector
DB25P female (I/F PBA)
NOTES
The handshaking (Flow control) / Data word length / Baud rate / Parity functions depend on the DIP
Switch settings. Refer to the Service manual.
3-5-1(b) RS-232C I/F Cable
Rev. 2.00
- 43 -
SRP-275
3-5-1(c) Cable Connection
(F.G) 1
1 (F.G)
(TXD) 2
2 (RXD)
(RXD) 3
3 (TXD)
(RTS) 4
4 (DTR)
(CTS) 5
5 (S.G)
(DSR) 6
6 (DSR)
(S.G) 7
7 (RTS)
(DTR) 20
8 (CTS)
PRINTER
SIDE
(25Pin)
3-5-1(d) Signal Description
Pin No. Signal name Signal direction
Body
Frame GND
2
TXD
Output
3
RXD
Input
6
DSR
Input
7
Signal GND
-
20
DTR
Output
HOST
SIDE
(9Pin)
Function
Frame ground
Transmit data
Receive data
This signal indicates whether the host computer can receive
data. (H/W flow control)
① MARK(Logic 1) : The host can not receive a data.
② SPACE(Logic 0) : The host can receive a data.
③ The printer transmits a data to the host, after confirming
this signal.
④ When XON/XOFF flow control is selected, the printer
does not check this signal.
Signal ground
This signal indicates whether the printer is busy.
(H/W flow control)
① MARK(Logic 1) : The printer is busy.
② SPACE(Logic 0) : The printer is not busy.
③ The host transmits a data to the printer, after confirming
this signal.
④ When XON/XOFF flow control is selected, the host does
not check this signal.
3-5-1(e) H/W Flow Control
When DTR/DSR flow control is select, before transmitting a data, the Printer checks whether the host is
BUSY or not. If the host is BUSY, the Printer does not transmit a data to the host. If the host is not BUSY, the
Printer transmits a data to the Host. The host is the same.
3-5-1(f) S/W Flow Control
When XON/XOFF flow control is selected, the printer transmits XON(ASCII 11h) or XOFF(ASCII 13h) signal
through the TXD line. If the printer is busy, the printer transmits XOFF(ASCII 13h) to host through the TXD
line. Then the host recognize that the printer is busy. So, the host does not transmit a data to the printer. If
printer is released from busy, the printer transmits XON(ASCII 11h) to host through the TXD line. Then the
host recognize that the printer is not busy. And the host transmit a data to the printer.
Rev. 2.00
- 44 -
SRP-275
3-5-2 IEEE1284 Parallel Interface
Bi-directional parallel interface : In accordance with the IEEE 1284 Nibble / Byte mode
3-5-2(a) Forward Mode Specification (Compatibility mode)
Data transmission from host computer to printer : Centronics compatible
Item
Description
Data transmission
Remark
• 8 bit parallel
Synchronization
• External supplied nStrobe signals
Handshaking
• nACK and Busy signals
Signal level
• TTL compatible
Connector
• IEEE1284 TYPE-B
3-5-2(b) Reverse Mode Specification (Nibble / Byte mode)
Data transmission from the printer to the host computer. The STATUS data transmission from the printer to
the host computer is accomplished in the Nibble or Byte mode. This mode allows data transmission from the
asynchronous printer under the control of the host computer. Data transmission in the Nibble mode are made
via the existing control lines in units of bits(Nibble). In the Byte mode, data transmission are proceeded by
making the 8-bits data lines bidirectional. Neither mode can operate at the same time as the compatibility
mode, so switching is always required.
3-5-2(c) Signal Specification (Compatibility/Nibble/Byte mode)
Pin no.
Source
Compatibility mode
Nibble mode
Byte mode
1
Host
nStrobe
HostClk
HostClk
2
Host / Printer
Data 0 (LSB)
-
Data 0 (LSB)
3
Host / Printer
Data 1
-
Data 1
4
Host / Printer
Data 2
-
Data 2
5
Host / Printer
Data 3
-
Data 3
6
Host / Printer
Data 4
-
Data 4
7
Host / Printer
Data 5
-
Data 5
8
Host / Printer
Data 6
-
Data 6
9
Host / Printer
Data 7 (MSB)
-
Data 7 (MSB)
10
Printer
nAck
PtrClk
PtrClk
11
Printer
Busy
PtrBusy / Data3,7
PtrBusy
12
Printer
Perror
AckDataReq / Data2,6
AckDataReq
13
Printer
Select
Xflag / Data1,5
Xflag
14
Host
nAutoFd
HostBusy
HostBusy
15
-
NC
ND
ND
16
-
GND
GND
GND
17
-
GND
FG
FG
18
Printer
Logic-H
Logic-H
Logic-H
-
GND
GND
GND
31
Host
nInit
nInit
nInit
32
Printer
nFault
nDataAbail /
nDataAvail
33
-
NC
ND
ND
34
Printer
NC
ND
ND
35
Printer
NC
ND
ND
36
Host
nSelectln
1284-Active
1284-Active
19~30
Rev. 2.00
- 45 -
SRP-275
3-5-2(c) IEEE1284 I/F Cable
3-5-3 USB Interface
SRP-275 support the USB (Universal Serial Bus) Communication.
3-5-3(a) Specification
Item
Transfer type
Data Signal
Data format
Transceiver
Speed
Power
Cable & connector
Other
3-5-3(b) Signal Description
Pin No.
Signal name
Shell
Shield
1
VBUS
2
D3
D+
4
GND
Description
• BULK
• Bi-direction, Half-duplex
• Differential signal pair (D+ / D-)
• NRZI format
• Zero bit stuffing after 6 ones
• Differential receive sensitivity : 200 mV
• Differential common mode range : 0.8~2.5 V
• Single-end receiver threshold : 0.8~2.0 V
• 12 Mbps
• Self-powered
• Cable : 5m / 2m
• Connector : A/B type
• Support USB spec V1.1
Assignment (Color)
Drain wire
Red
White
Green
Black
Function
Frame ground
NC
Differential data line
Differential data line
Signal ground
3-5-3(c) USB I/F Cable
Rev. 2.00
Remark
- 46 -
SRP-275
3-6 Drawer Kick-Out Specifications
3-6-1 Drawer Cable
3-6-2 Cable Connection
Pin No.
Rev. 2.00
Description
1
Signal GND
2
Drawer kick-out driver signal #1
3
Drawer Open / Close signal
4
+24V
5
Drawer kick-out driver signal #2
6
Signal GND
Direction
Output
Input
Output
-
- 47 -
SRP-275
4. Hardware
4-1 Wiring Diagram
4-1-1 Main board wiring diagram
Drawer
J1
JTAG connector
PCB connector
sub
J2
J12
Operation panel
connector
J11
J8
J10
Printer mechanism
Rev. 2.00
J15
J6
Power connector
Interface
connector
- 48 -
Power jack
DC
SRP-275
4-1-2 Connector sub PCB wiring diagram
Rear cover open
switch
J5
Black mark
Sensor
J7
Auto cutter
connector
J9
J16
Paper near end
switch
J3
Paper near end
wall mount switch
J13
Paper end
Sensor
J4
Rev. 2.00
- 49 -
Main board
SRP-275
AC adapter
DC24V
Power
supply
circuit
RS-232
driver
RS-232C
connector
IEEE1284
driver
Parallel
connector
USB
driver
USB
connector
Sensor
circuit
Paper end,
home position
sensor
Head
driver
Printerhead dot
+24V
+5V
I/F board
4-2 Block Diagram
EEPROM
M24C04
Flash
memory
M29F800
Data
Address
CPU
S3C4640X01
HF motor
driver
Data
DRAM
K4F151611D
Address
HF Motor
LED &
switch
LED &
button
circuit
DIP
Switch
DIP
sensing
circuit
Drawer &
buzzer
Clock
(10MHz)
Rev. 2.00
Driver
Clock
circuit
(40MHz)
- 50 -
Auto cutter
Drive
Auto cutter,
home position
sensor
Sensor
circuit
Paper near end,
Paper near end-W,
Rear cover open
PF Motor
Driver
PF Motor
Printer mechanism
Reset
circuit
SRP-275
4-3 PCB Layout & Part List
4-3-1 Main Board
* Type of SRP-275A : blue color
* Type of SRP-275C : green color
[[Top view]
Rev. 2.00
- 51 -
SRP-275
[Bottom view]
Rev. 2.00
- 52 -
SRP-275
* Type of SRP-275A (SRP-275MBA)
No.
Code no.
Description
Specification
Q'ty
9-3-1
9-3-2
9-3-3
9-3-4
9-3-5
9-3-6
9-3-7
9-3-8
9-3-9
9-3-10
9-3-11
9-3-12
9-3-13
9-3-14
9-3-15
9-3-16
9-3-17
9-3-18
9-3-19
9-3-20
9-3-21
9-3-22
AP02-00063A
AP02-00063D
AP02-00063E
K302-00011A
0903-001282
0506-001019
0801-000718
1003-001102
1103-001096
1105-001394
1107-001121
1202-000188
1203-000404
1203-002523
4701-001037
K502-00033A
K702-00023A
0401-001110
0402-000309
0402-001389
0406-000129
0406-001158
0501-000457
0503-001037
2011-000005
SRP-275MBAS
SRP-275MBAG
SRP-275MBAB
PCB-MAIN
IC-MICROCONTROLLER
IC-TR-ARRAY
IC (3 STATE OUT NONINVERT)
IC-MOTOR DRIVER
IC-EEPROM
IC-DRAM
IC-FLASH MEMORY
IC-VOLTAGE COMP.
IC-INVERTING SWITCH REGULATOR
IC-VOL. DETECTOR
IC-FREQ-ATTENUATOR
IC (2INPUT AND GATE)
DIODE-ARRAY
DIODE-SWITCHING
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-TVS
DIODE-TVS
TR-SMALL SIGNAL
TR-DARLINGTON
R-ARRAY
ASS’Y (A TYPE,STD)
ASS’Y (A TYPE,GB2312)
ASS’Y (A TYPE,BIG5)
4-LAYER, FR-4,T1.6
S3C4640, 32BIT,QFP,160P
STA471A,NPN,4,4W
74HC574,SOIC20
TEA3718DP,DIP,16P
24LC04B, SOIC8
K4F151611D-JL60, SOJ42,
M29F800DB,TSOP48
10393,SOP,8P,244MIL,
MC34063A,SOP,8P,150M
KIA7045,SOT-89,4P,98MIL
FS784,SOIC,8P,6to82MHz
NC7S08P5X,5PIN, SC70
UMP1N
1SS400,80V,300MA
1SR154-400,400V,1A,S
RB050L-40,40V,3A,SOD
P6KE6.8A,6.45/6.8/7.
P6KE30A,28.50-31.50V
MMBT2222ALT1,NPN
2SD2170,NPN,2W,SC-62
220ohm, 5%, 1/16W, 8PIN
1
1
1
1
1
3
4
2
1
1
1
1
1
1
1
1
4
3
3
3
1
1
4
1
2
9-3-23
K802-00034A
R-ARRAY
100ohm, 5%, 1/16W, 8PIN
9
9-3-24
9-3-25
9-3-26
9-3-27
9-3-28
9-3-29
K802-00039A
2001-000015
K802-00066A
2005-000419
2007-000052
2007-000070
R-ARRAY
R-CARBON(S)
R-CARBON(S)
R-WIRE WOUND
R-CHIP
R-CHIP
330ohm, 5%, 1/16W, 8PIN
0.5ohm.5%.1/2W.AA.TP
0.47ohm,5%,1/2W,AA,T
0.33ohm,1%,1W,AA,TP
10Kohm,1%,1/16W,1608
0ohm,5%,1608 TP
2
2
1
1
1
3
9-3-30
2007-000074
R-CHIP
100ohm,5%,1/16W,1608
6
9-3-31
2007-000078
R-CHIP
1Kohm,5%,1/16W,1608
7
9-3-32
2007-000082
R-CHIP
3.3Kohm.5%,1/16W,1608
1
9-3-33
2007-000084
R-CHIP
4.7Kohm,5%,1/16W,1608
10
9-3-34
2007-000090
R-CHIP
10Kohm.5%,1/16W,1608
10
9-3-35
9-3-36
9-3-37
9-3-38
9-3-39
9-3-40
2007-000092
2007-000094
2007-000098
2007-000539
2007-000704
2007-000803
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
15Kohm,5%,1/16W,1608
22Kohm,5%,1/16W,1608
56Kohm,5%,1/16W,1608
200ohm,5%,1/16W,1608
3.6Kohm,5%,1/16W,1608
36Kohm,1%,1/16W,1608
4
2
2
2
3
1
9-3-41
2007-000965
R-CHIP
5.1Kohm,5%,1/16W,1608
6
9-3-42
9-3-43
9-3-44
9-3-45
9-3-46
2007-001433
2007-007440
K802-00038F
K804-00009A
K804-00027A
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
12Kohm,1%,1/16W,1608
510ohm,1%,1/16W,1608
1.5Kohm, 1%, 1/16W,1608
220ohm,5%,1/16W,1608
330ohm, 5%, 1/16W,1608
1
1
1
1
1
9-3
Rev. 2.00
- 53 -
Location
U1
U5, U7, U9
U2, U3, U6, U8
U15, U17
U14
U13
U12
U4
U18
U11
U10
U19
DR1, DR2, DR3, DR4
D20, D21, D22
D17, D18, D19
D23, D27, D28
ZD2
ZD1
Q2, Q3, Q4, Q5
Q1
RA1, RA2
RA3, RA4, RA5, RA6,
RA7, RA8, RA9, RA10,
RA11
RA12, RA13
R60, R67
R68
R76
R64
R23, R53, R54
R44, R45, R46, R47, R48,
R49
R9, R14, R16, R18, R51,
R58, R65
R43
R1, R2, R3, R4, R15, R17,
R20, R21, R22, R71
R11, R36, R37, R38, R39,
R41, R50, R52, R55, R56
R5, R6, R7, R8
R78, R79
R59, R66
R40, R42
R27, R29, R33
R69
R10, R12, R26, R28, R32,
R57
R70
R61
R13
R19
R77
Serviceable
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
SRP-275
No.
Code no.
Description
Specification
Q'ty
9-3-47
2203-000236
C-CERAMIC,CHIP
0.1nF,5%,50V,C0G,1608
25
9-3-48
2203-000476
C-CDRAMIC.CHIP
1000nF,+80-20%,2012
1
9-3-49
2203-000626
C-CERAMIC,CHIP
0.022NF.5%.50V.1608
12
9-3-50
9-3-51
9-3-52
2203-001222
2203-002041
2203-005194
C-CERAMIC.CHIP
C-CDRAMIC.CHIP
C-CERAMIC.CHIP
820pF,10%,50V,1608
0.47nF,10%,50V,1608
220pF,10%,50V,1608
5
1
1
9-3-53
2203-005249
C-CERAMIC,CHIP
100nF,10%,50V,1608
30
9-3-54
9-3-55
9-3-56
9-3-57
9-3-58
9-3-59
9-3-60
9-3-61
9-3-62
9-3-63
9-3-64
9-3-65
9-3-66
9-3-67
9-3-68
9-3-69
2401-000056
2401-000324
2401-003775
2702-001119
2801-004219
3301-000317
3407-000177
3601-001180
3702-001171
3708-001058
3708-001708
3711-000820
K602-00069A
3722-000550
3722-001035
K204-00012A
C-AL
C-AL
C-AL
INDUCTOR-RADIAL
CRYSTAL-SMD
CORE-FERRITE BEAD
SWITCH-DIP
FUSE-SURFACE MOUNT
CONNECTOR-RIBBON
CONNECTOR-FPC/FFC/PIC
CONNECTOR-FPC/FFC/PIC
CONNECTOR-HEADER
CONNECTOR-HEADER
JACK-MODULAR
JACK-DC POWER
BUZZER
470uF,20%,35V,GP
100uF,20%,35V,GP
470uF,20%,16V,WT
220uH,15%,13X18MM
10MHZ,30PPM,28-AA
CIM21J121, 2012
5V,10mA,SLIDE,SPST
125V,3.5A,FAST-ACTIN
40P,FEMALE,RIGHTANGL
30P,1MM,STRAIGHT,S,
16P,1MM,STRAIGHT,S
BOX,2P,1R,2.5MM,STRA
BOX,6P,1R,2MM,STRAI
6P,9.86MM,AU50U,GRY
3P,6.3mm,ANGLE
85dB, 5V, MAX30mA,
1
1
1
1
1
6
2
1
1
1
1
1
1
1
1
1
Rev. 2.00
- 54 -
Location
C30, C58, C59, C60, C61,
C62, C63, C64, C65, C66,
C67, C68, C69, C70, C71,
C72, C73, C74, C75, C76,
C77, C78, C79, C80, C81
C20
C12, C19, C21, C23, C24,
C25, C26, C27, C28, C40,
C41, C48
C22, C42, C43, C49, C50
C5
C53
C1, C2, C3, C4, C6, C7,
C10, C13, C14, C15, C16,
C17, C18, C29, C31, C32,
C33, C34, C35, C36, C37,
C38, C39, C44, C45, C46,
C47, C52, C56, C57
C51
C54
C55
L6
Y1
L1, L2, L3, L4, L5, L7
SW1, SW2
FU1
J6
J10
J15
J11
J2
J1
J12
LS1
Serviceable
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
SRP-275
* Type of SRP-275C (SRP-275MBC)
No.
Code no.
Description
Specification
Q'ty
9-3-1
9-3-2
9-3-3
9-3-4
9-3-5
9-3-6
9-3-7
9-3-8
9-3-9
9-3-10
9-3-11
9-3-12
9-3-13
9-3-14
9-3-15
9-3-16
9-3-17
9-3-18
9-3-19
9-3-20
9-3-21
9-3-22
9-3-23
AP02-00063C
AP02-00063F
AP02-00063G
K302-00011A
0903-001282
0506-001019
0801-000718
1003-001102
1003-001470
1103-001096
1105-001394
1107-001121
1202-000188
1203-000404
1203-002523
4701-001037
K502-00033A
K702-00023A
0401-001110
0402-000309
0402-001389
0406-000129
0406-001158
0501-000457
0503-001037
2011-000005
SRP-275MBCS
SRP-275MBCG
SRP-275MBCB
PCB-MAIN
IC-MICROCONTROLLER
IC-TR-ARRAY
IC (3 STATE OUT NONINVERT)
IC-MOTOR DRIVER
IC-MOTOR DRIVER
IC-EEPROM
IC-DRAM
IC-FLASH MEMORY
IC-VOLTAGE COMP.
IC-INVERTING SWITCH REGULATOR
IC-VOL. DETECTOR
IC-FREQ-ATTENUATOR
IC (2INPUT AND GATE)
DIODE-ARRAY
DIODE-SWITCHING
DIODE-RECTIFIER
DIODE-RECTIFIER
DIODE-TVS
DIODE-TVS
TR-SMALL SIGNAL
TR-DARLINGTON
R-ARRAY
ASS’Y (C TYPE,STD)
ASS’Y (C TYPE,GB2312)
ASS’Y (C TYPE,BIG5)
4-LAYER, FR-4,T1.6
S3C4640, 32BIT,QFP,160P
STA471A,NPN,4,4W
74HC574,SOIC20
TEA3718DP,DIP,16P
BA6920FP-Y,SOIC,25P,
24LC04B, SOIC8
K4F151611D-JL60, SOJ42,
M29F800DB,TSOP48
10393,SOP,8P,244MIL,
MC34063A,SOP,8P,150M
KIA7045,SOT-89,4P,98MIL
FS784,SOIC,8P,6to82MHz
NC7S08P5X,5PIN, SC70
UMP1N
1SS400,80V,300MA
1SR154-400,400V,1A,S
RB050L-40,40V,3A,SOD
P6KE6.8A,6.45/6.8/7.
P6KE30A,28.50-31.50V
MMBT2222ALT1,NPN
2SD2170,NPN,2W,SC-62
220ohm, 5%, 1/16W, 8PIN
1
1
1
1
1
3
4
2
1
1
1
1
1
1
1
1
1
4
3
3
3
1
1
4
1
2
9-3-24
K802-00034A
R-ARRAY
100ohm, 5%, 1/16W, 8PIN
9
9-3-25
9-3-26
9-3-27
9-3-28
9-3-29
9-3-30
K802-00039A
2001-000015
K802-00066A
2005-000419
2007-000052
2007-000070
R-ARRAY
R-CARBON(S)
R-CARBON(S)
R-WIRE WOUND
R-CHIP
R-CHIP
330ohm, 5%, 1/16W, 8PIN
0.5ohm.5%.1/2W.AA.TP
0.47ohm,5%,1/2W,AA,T
0.33ohm,1%,1W,AA,TP
10Kohm,1%,1/16W,1608
0ohm,5%,1608 TP
2
2
1
1
1
3
9-3-31
2007-000074
R-CHIP
100ohm,5%,1/16W,1608
6
9-3-32
2007-000078
R-CHIP
1Kohm,5%,1/16W,1608
7
9-3-33
2007-000082
R-CHIP
3.3Kohm.5%,1/16W,1608
1
9-3-34
2007-000084
R-CHIP
4.7Kohm,5%,1/16W,1608
10
9-3-35
2007-000090
R-CHIP
10Kohm.5%,1/16W,1608
10
9-3-36
9-3-37
9-3-38
9-3-39
9-3-40
9-3-41
2007-000092
2007-000094
2007-000098
2007-000539
2007-000704
2007-000803
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
15Kohm,5%,1/16W,1608
22Kohm,5%,1/16W,1608
56Kohm,5%,1/16W,1608
200ohm,5%,1/16W,1608
3.6Kohm,5%,1/16W,1608
36Kohm,1%,1/16W,1608
4
2
2
2
3
1
9-3-42
2007-000965
R-CHIP
5.1Kohm,5%,1/16W,1608
6
9-3-43
9-3-44
9-3-45
9-3-46
9-3-47
2007-001433
2007-007440
K802-00038F
K804-00009A
K804-00027A
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
12Kohm,1%,1/16W,1608
510ohm,1%,1/16W,1608
1.5Kohm, 1%, 1/16W,1608
220ohm,5%,1/16W,1608
330ohm, 5%, 1/16W,1608
1
1
1
1
1
9-3
Rev. 2.00
- 55 -
Location
U1
U5, U7, U9
U2, U3, U6, U8
U15, U17
U16
U14
U13
U12
U4
U18
U11
U10
U19
DR1, DR2, DR3, DR4
D20, D21, D22
D17, D18, D19
D23, D27, D28
ZD2
ZD1
Q2, Q3, Q4, Q5
Q1
RA1, RA2
RA3, RA4, RA5, RA6,
RA7, RA8, RA9, RA10,
RA11
RA12, RA13
R60, R67
R68
R76
R64
R23, R53, R54
R44, R45, R46, R47, R48,
R49
R9, R14, R16, R18, R51,
R58, R65
R43
R1, R2, R3, R4, R15, R17,
R20, R21, R22, R71
R11, R36, R37, R38, R39,
R41, R50, R52, R55, R56
R5, R6, R7, R8
R78, R79
R59, R66
R40, R42
R27, R29, R33
R69
R10, R12, R26, R28, R32,
R57
R70
R61
R13
R19
R77
Serviceable
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
SRP-275
No.
Code no.
Description
Specification
Q'ty
9-3-48
2203-000236
C-CERAMIC,CHIP
0.1nF,5%,50V,C0G,1608
25
9-3-49
2203-000476
C-CDRAMIC.CHIP
1000nF,+80-20%,2012
1
9-3-50
2203-000626
C-CERAMIC,CHIP
0.022NF.5%.50V.1608
12
9-3-51
9-3-52
9-3-53
2203-001222
2203-002041
2203-005194
C-CERAMIC.CHIP
C-CDRAMIC.CHIP
C-CERAMIC.CHIP
820pF,10%,50V,1608
0.47nF,10%,50V,1608
220pF,10%,50V,1608
5
1
1
9-3-54
2203-005249
C-CERAMIC,CHIP
100nF,10%,50V,1608
30
9-3-55
9-3-56
9-3-57
9-3-58
9-3-59
9-3-60
9-3-61
9-3-62
9-3-63
9-3-64
9-3-65
9-3-66
9-3-67
9-3-68
9-3-69
9-3-70
2401-000056
2401-000324
2401-003775
2702-001119
2801-004219
3301-000317
3407-000177
3601-001180
3702-001171
3708-001058
3708-001708
3711-000820
K602-00069A
3722-000550
3722-001035
K204-00012A
C-AL
C-AL
C-AL
INDUCTOR-RADIAL
CRYSTAL-SMD
CORE-FERRITE BEAD
SWITCH-DIP
FUSE-SURFACE MOUNT
CONNECTOR-RIBBON
CONNECTOR-FPC/FFC/PIC
CONNECTOR-FPC/FFC/PIC
CONNECTOR-HEADER
CONNECTOR-HEADER
JACK-MODULAR
JACK-DC POWER
BUZZER
470uF,20%,35V,GP
100uF,20%,35V,GP
470uF,20%,16V,WT
220uH,15%,13X18MM
10MHZ,30PPM,28-AA
CIM21J121, 2012
5V,10mA,SLIDE,SPST
125V,3.5A,FAST-ACTIN
40P,FEMALE,RIGHTANGL
30P,1MM,STRAIGHT,S,
16P,1MM,STRAIGHT,S
BOX,2P,1R,2.5MM,STRA
BOX,6P,1R,2MM,STRAI
6P,9.86MM,AU50U,GRY
3P,6.3mm,ANGLE
85dB, 5V, MAX30mA,
1
1
1
1
1
6
2
1
1
1
1
1
1
1
1
1
Rev. 2.00
- 56 -
Location
C30, C58, C59, C60, C61,
C62, C63, C64, C65, C66,
C67, C68, C69, C70, C71,
C72, C73, C74, C75, C76,
C77, C78, C79, C80, C81
C20
C12, C19, C21, C23, C24,
C25, C26, C27, C28, C40,
C41, C48
C22, C42, C43, C49, C50
C5
C53
C1, C2, C3, C4, C6, C7,
C10, C13, C14, C15, C16,
C17, C18, C29, C31, C32,
C33, C34, C35, C36, C37,
C38, C39, C44, C45, C46,
C47, C52, C56, C57
C51
C54
C55
L6
Y1
L1, L2, L3, L4, L5, L7
SW1, SW2
FU1
J6
J10
J15
J11
J2
J1
J12
LS1
Serviceable
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
SRP-275
4-4-2 ASSY-PCB-CONNECTOR SUB
* Type of SRP-275A
No.
Code No.
3-7
3-7-1
3-7-2
3-7-3
3-7-4
3-7-5
3-7-6
3-7-7
3-7-8
3-7-9
3-7-10
3-7-11
AP02-00062A
K302-00019A
2007-000090
2007-000539
2007-000078
2007-000084
2007-000082
2203-005249
3301-000317
3711-000827
3711-000907
3708-001708
* Type of SRP-275C
No.
Code No.
3-7
3-7-1
3-7-2
3-7-3
3-7-4
3-7-5
3-7-6
3-7-7
3-7-8
3-7-9
3-7-10
3-7-11
3-7-12
AP02-00062C
K302-00019A
2007-000090
2007-000539
2007-000078
2007-000084
2007-000082
2203-005249
3301-000317
3711-000827
3711-000907
3711-001018
3708-001708
Rev. 2.00
Description
PCB-CONNECTOR SUB-A ASS'Y
PCB-CONNECTOR SUB
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
C-CERAMIC,CHIP
CORE-FERRITE BEAD
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-FPC/FFC/PIC
Description
PCB-CONNECTOR SUB-C ASS'Y
PCB-CONNECTOR SUB
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
C-CERAMIC,CHIP
CORE-FERRITE BEAD
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-FPC/FFC/PIC
Specification
ASS'Y (A TYPE)
4-LAYER, FR-4,T1.6
10Kohm.5%,1/16W,1608
200ohm,5%,1/16W,1608
1Kohm,5%,1/16W,1608
4.7Kohm,5%,1/16W,1608
3.3Kohm.5%,1/16W,1608
100nF,10%,50V,1608
CIM21J121, 2012
BOX,2P,1R,2mm,STRAIG
BOX,3P,1R,2mm,STRAIG
16P,1MM,STRAIGHT,S
Specification
ASS'Y (C TYPE)
4-LAYER, FR-4,T1.6
10Kohm.5%,1/16W,1608
200ohm,5%,1/16W,1608
1Kohm,5%,1/16W,1608
4.7Kohm,5%,1/16W,1608
3.3Kohm.5%,1/16W,1608
100nF,10%,50V,1608
CIM21J121, 2012
BOX,2P,1R,2mm,STRAIG
BOX,3P,1R,2mm,STRAIG
BOX,5P,1R,2MM,STRAI
16P,1MM,STRAIGHT,S
- 57 -
Q'ty
1
1
1
1
2
3
1
3
1
3
2
1
Q'ty
1
1
1
1
2
3
1
3
1
3
2
1
1
Location
R62
R63
R25, R35
R24, R30, R34
R31
C8, C9, C11
L8
J3, J5, J13
J4, J7
J16
Location
R62
R63
R25, R35
R24, R30, R34
R31
C8, C9, C11
L8
J3, J5, J13
J4, J7
J9
J16
Serviceable
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Serviceable
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
SRP-275
4-4-3 ASSY-OPERATION PANEL
No.
7-6
7-6-1
7-6-2
7-6-3
7-6-4
7-6-5
7-6-6
7-6-7
Code No.
AZ02-00024A
K302-00013A
0601-001374
0601-001376
2007-000539
2007-000094
3404-001205
K602-00069A
Rev. 2.00
Description
ASSY-OPERATION PANEL
PCB-OPERATION PANEL
DIODE-LED
DIODE-LED
R-CHIP
R-CHIP
SWITCH-TACT
CONNECTOR-HEADER
Specification
ASS'Y
4-LAYER,FR-4,1.6T
RED, 3pi, DIP
GREED, 3pi, DIP
200ohm,5%,1/16W,1608
22Kohm,5%,1/16W,1608
12VDC,50MA,260GF,6.0
BOX,6P,1R,2MM,STRAI
- 58 -
Q'ty
1
1
2
1
3
1
1
1
Location
D24, D25
D26
R73, R74, R75
R72
SW3
J14
Serviceable
Y
N
Y
Y
Y
Y
Y
Y
SRP-275
4-4-4 ASSY-PCB-HEAD
No.
Code No.
Description
1-18
1-18-1
1-18-2
1-18-3
1-18-4
1-18-5
1-18-6
1-18-7
1-18-8
1-18-9
1-18-10
1-18-11
1-18-12
1-18-13
1-18-14
1-18-15
1-18-16
1-18-17
1-18-18
1-18-19
1-18-20
1-18-21
1-18-22
AP03-00060A
K302-00012A
1003-001049
0604-001237
0501-000457
2007-007961
2007-000078
2007-007440
K802-00044F
2007-000097
2007-000090
2007-000539
2007-000659
K802-00045F
2203-005249
2203-000626
2203-000440
2203-002041
3711-000827
K602-00070A
3711-001061
3708-001058
3708-000155
ASSY-PCB-HEAD
PCB-HEAD
IC-MOTOR DRIVER
PHOTO INTERRUPTER
TR-SMALL SIGNAL
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
C-CERAMIC,CHIP
C-CERAMIC.CHIP
C-CDRAMIC.CHIP
C-CERAMIC,CHIP
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-HEADER
CONNECTOR-FPC/FFC/PIC
CONNECTOR-FPC/FFC/PIC
Rev. 2.00
Specification
ASS'Y
4-LAYER, FR-4,T1.6
SLA7024M,DIP,18P,31M
RPI352C
MMBT2222ALT1,NPN,
1ohm,1%,1W,DA,TP,6432
1Kohm,5%,1/16W,1608
510ohm,1%,1/16W,1608
680ohm, 1%, 1/16W.1608
47Kohm,5%,1/16W,1608
10Kohm.5%,1/16W,1608
200ohm,5%,1/16W,1608
27ohm,1%,1/16W,1608
100ohm,1%,1/16W,1608
100nF,10%,50V,1608
0.022NF.5%.50V.1608
1nF.10%,50V.1608
0.47nF,10%,50V,1608
BOX,2P,1R,2mm
BOX,4P,1R,2.5mm,R/A
BOX,6P,1R,2mm,R/A
30P,1MM,STRAIGHT,S
14P,1MM,R/A,S
- 59 -
Q'ty
1
1
1
1
1
2
2
2
1
2
1
1
1
1
5
2
2
2
1
1
1
1
1
Location
U1
PD1
Q1
R6, R7
R1, R11
R4, R5
R8
R2, R3
R12
R13
R9
R10
C1, C2, C3, C10, C11
C4, C5
C6, C7
C8, C9
J5
J4
J3
J2
J1
Serviceable
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
SRP-275
4-4-5 Serial Interface (RS-232C)
* IFC-S TYPE
No.
Code No
14-2
14-2-1
14-2-2
14-2-3
14-2-4
14-2-5
14-2-6
14-2-7
14-2-8
14-2-9
14-2-10
14-2-11
14-2-12
JE94-08001A
JE41-00082N
0406-000129
1006-001262
2007-000070
2007-000090
2203-002041
2203-005249
2401-000205
2401-001801
3301-000325
3701-001272
3702-001172
Rev. 2.00
Description
ASSY-PCB-IFC-S TYPE
PCB-IFC-S TYPE
DIODE-TVS
IC-DRIVER/RECEIVER
R-CHIP
R-CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-AL
C-AL
CORE-FERRITE BEAD
CONNECTOR-DSUB
CONNECTOR-RIBBON
Specification
ASS'Y
FR4,4LAYER,T1.6MM
P6KE6.8A,6.45/6.8/7.
ST232,SO-16,16P,150M
0ohm,5%,1608 TP
10KOHM.5%,1/16W,DA,T
0.47nF,10%,50V,X7R,T
100nF,10%,50V,X7R,TP
100uF.20%,16V,GP,TP
100nF,20%,50V,GP,TP,
AB,3.2x2.5x1.3mm
25P,2R,FEMALE.ANGLE.
40P,MALE,RIGHTANGLE,
- 60 -
Q'ty
1
1
1
1
2
2
4
2
1
4
6
1
1
Location
ZD1
U1
R3, R4
R1, R2
C8, C9, C10, C11
C1, C4
C3
C2, C5, C6, C7
L1, L2, L3, L4, L5, L6
J1
J2
Serviceable
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
SRP-275
4-4-6 Parallel Interface (IEEE1284)
* IFC-P TYPE
No.
Code No.
Description
Specification
Q'ty
14-2
14-2-1
14-2-2
14-2-3
JE94-06001A
JE41-00082M
0801-000928
0406-000129
PCB-IFC-P TYPE ASS'Y
PCB-IFC-P TYPE
IC
DIODE-TVS
ASS'Y
FR4,4LAYER,T1.6MM
74HCT245
P6KE6.8A,6.45/6.8/7.
1
1
1
1
14-2-4
2007-000078
R-CHIP
1Kohm,5%,1/16W,1608
9
14-2-5
14-2-6
2007-000116
2007-000539
R-CHIP
R-CHIP
120ohm.5%,1/16W,1608
200ohm,5%,1/16W,1608
1
3
14-2-7
2007-000965
R-CHIP
5.1Kohm,5%,1/16W,1608
10
14-2-8
2007-000839
R-CHIP
39ohm,5%,1/16W.1608
13
14-2-9
2203-000236
C-CERAMIC,CHIP
0.1nF,5%,50V,C0G,1608
3
14-2-10
2203-000440
C-CERAMIC.CHIP
1nF.10%,50V.X7R.1608
9
14-2-11
14-2-12
14-2-13
14-2-14
14-2-15
14-2-16
2203-000626
2203-005194
2203-005249
3301-000325
3702-000118
3702-001172
C-CERAMIC.CHIP
C-CERAMIC.CHIP
C-CERAMIC,CHIP
CORE-FERRITE BEAD
CONNECTOR-RIBBON
CONNECTOR-RIBBON
0.022NF.5%.50V.1608
220pF,10%,50V,1608
100nF,10%,50V,1608
CIB32P600, AB, 3525
36P,FEMALE,ANGLE,AUF
40P,MALE,RIGHTANGLE,
5
1
3
2
1
1
Rev. 2.00
- 61 -
Location
U1
ZD1
R1, R3, R4, R5, R6, R7, R8,
R9, R10
R2
R34, R35, R36
R19, R20, R21, R22, R23,
R29, R30, R31, R32, R33
R11, R12, R13, R14, R15,
R16, R17, R18, R24, R25,
R26, R27, R28
C19, C20, C21
C3, C4, C5, C6, C7, C8, C9,
C10, C12
C14, C15, C16, C17, C18
C1
C2, C12, C13
L1, L2
J1
J2
Serviceable
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
SRP-275
4-4-7 USB Interface
* IFC-U TYPE
No.
Code No.
Description
14-2
14-2-1
JE94-07001A
JE41-00486B
PCB-IFC-U TYPE ASS'Y
PCB-IFC-U TYPE
14-2-2
K504-00035A
IC-USB CONTROL
14-2-3
14-2-4
14-2-5
14-2-6
2007-000090
2007-000239
2007-000659
K804-00007A
14-2-7
Specification
Q'ty
1
1
R-CHIP
R-CHIP
R-CHIP
R-CHIP
ASS'Y
FR4,4LAYER,T1.6MM
USBN9603-28M,8BIT,SOP,
28P, 300MIL,48MHz,3.3V
10Kohm.5%,1/16W,DA,T
1.5Kohm,1%,1/16W,1608
27ohm,1%,1/16W,1608
1Mohm, 5%, 1608
2203-000626
C-CERAMIC,CHIP
22pF,10%,50V,1608
9
14-2-8
14-2-9
14-2-10
14-2-11
14-2-12
14-2-13
14-2-14
2203-005194
2203-005249
K006-00007A
2404-000128
2404-000190
K006-00008A
0406-000129
C-CERAMIC.CHIP
C-CERAMIC,CHIP
C-CERAMIC,CHIP
C-TANTAL,CHIP
C-TANTAL,CHIP
C-TANTAL,CHIP
DIODE-TVS
220pF,10%,50V,X7R,TP
100nF,10%,50V,1608
1000pF,10%,50V,1608
10uF,16V,10%,1W,6032
22uF,16V,10%,1W,6032
100uF,16V,10%,1W,6032
P6KE6.8A,600W,DIP
2
2
1
1
1
1
1
14-2-15
3301-000317
FERRITE BEAD,CHIP
CIM21J121NES,2012
9
14-2-16
K204-00016A
CRYSTAL-SMD
14-2-17
3702-001172
CONNECTOR-RIBBON
14-2-18
3722-001101
CONNECTOR
SX-1,24MHz,20pF
I/F_CON
(40P,MALE,RIGHT NGLE,AU)
USB PORT_B TYPE
Rev. 2.00
- 62 -
Location
Serviceable
Y
N
1
U1
Y
3
1
2
1
Y
Y
Y
Y
1
R1, R2, R3
R8
R6, R7
R5
C3, C4, C5, C6, C7, C10,
C11, C16, C17
C18, C19
C1, C9
C8
C15
C2
C14
ZD1
L1, L2, L3, L4, L5, L6, L7, L8,
L9
Y1
1
J1
Y
1
J2
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
SRP-275
4-4-8 Ethernet Interface
* IFC-E TYPE
Rev. 2.00
- 63 -
SRP-275
No.
14-2
14-2-1
14-2-2
14-2-3
14-2-4
14-2-5
14-2-6
14-2-7
14-2-8
14-2-9
14-2-10
14-2-11
14-2-12
14-2-13
14-2-14
Code No.
AP06-00081A
K302-00048A
K508-00043A
K508-00042A
K508-00046A
K508-00045A
K508-00047A
K508-00044A
K508-00039A
K508-00040A
K508-00041A
K504-00023A
1103-001096
K704-00017A
K704-00021A
Description
PCB-IFC-E TYPE ASS'Y
PCB-IFC-E TYPE
IC-MICROCONTROLLER
IC-SRAM
IC-RESET
IC-REGULATOR
IC-PHY
IC-TCP/IP
IC-LOGIC
IC-LOGIC
IC-LOGIC
IC-LOGIC
IC-EEPROM
Specification
ASS'Y
2-LAYER, FR-4, 1.6T
AT89C51RC2-RLTIM
K6R1008V1D-UI10, TSOP2-32
ASM811SEUS_T, SOT143
LM1117, SOT223
RTL8201BL, LQFP48
W3100A, LQFP64
74HC04, TSSOP14
74HC08, TSSOP14
74HC573, TSSOP20
74LCX245, TSSOP20
M24C04W, SO8
BAW56
KDS181
Q'ty
1
1
1
1
1
1
1
1
1
1
1
2
1
14-2-15
2007-000070
R-CHIP
0ohm, 5%, 1/16W, 50V, 1608
11
14-2-16
2007-000078
R-CHIP
1Kohm, 5%, 1/16W, 50V, 1608
1
14-2-17
2007-000084
R-CHIP
4.7Kohm, 5%, 1/16W, 50V, 1608
11
14-2-18
14-2-19
14-2-20
14-2-21
14-2-22
14-2-23
2007-000090
2007-000239
2007-000539
K808-00060A
K808-00061F
2203-000626
R-CHIP
R-CHIP
R-CHIP
R-CHIP
R-CHIP
C-CERAMIC, CHIP
10Kohm, 5%, 1/16W, 50V, 1608
1.5Kohm, 5%, 1/16W, 50V, 1608
200ohm, 5%, 1/16W, 50V, 1608
51ohm, 5%, 1/16W, 50V, 1608
5.9Kohm, 1%, 1/16W, 50V, 1608
22pF, 5~10%, 50V
5
1
4
4
1
4
14-2-24
2203-005249
C-CERAMIC, CHIP
100nF, 5~10%, 50V
29
14-2-25
14-2-26
14-2-27
14-2-28
14-2-29
14-2-30
14-2-31
14-2-32
14-2-33
14-2-34
K008-00007A
2402-000168
3301-000317
3301-000325
K902-00007A
K204-00014A
3702-001172
K608-00095A
K208-00018A
K208-00019A
C-TANTAL, CHIP
C-AL, CMD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
CORE-FERRITE BEAD
DIP-SWITCH
CONNECTOR-RIBBON
CONNECTOR-ETHERNET
CRYSTAL
CRYSTAL
33uF, 10V, 3528
100uF, 16V, SMD
CIM21J121, 120ohm, 2012
CIB32P600, 60ohm, 3525
CIM21U100, 100ohm, 2012
5V, 10mA, SLIDE, SPST
I/F_CON(40P,MALE,RIGHT ANGLE,AU)
RJ-45, Tab Down LED
22.1184MHz, DIP & SMD
25MHz, DIP, SMD
2
1
2
2
4
1
1
1
1
1
Rev. 2.00
DIODE-SWITCHING
- 64 -
1
Location
U1
U3
U7
U9
U12
U11
U6
U5
U2
U8, U10
U4
D1
R10, R11, R12, R13, R14,
R15, R16, R17, R18, R19,
R20
R29
R1, R2, R3, R4, R22, R23,
R24, R25, R26, R27, R31
R5, R6, R8, R9, R38
R21
R7, R30, R32, R33
R34, R35, R36, R37
R28
C5, C6, C29, C30
C1, C2, C3, C4, C7, C8,
C9, C10, C11, C12, C13,
C14, C15, C17, C19, C20,
C21, C22, C23, C24, C25,
C26, C28, C31, C32, C33,
C34, C35, C36
C18, C27
C16
L2, L3
L1, L4
L5, L6, L7, L8
SW1
J1
J2
Y1
Y2
Serviceable
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
SRP-275
4-5 Schematic Diagram
4-5-1 Main Circuit Diagram
Rev. 2.00
- 65 -
SRP-275
Rev. 2.00
- 66 -
SRP-275
Rev. 2.00
- 67 -
SRP-275
Rev. 2.00
- 68 -
SRP-275
Rev. 2.00
- 69 -
SRP-275
Rev. 2.00
- 70 -
SRP-275
Rev. 2.00
- 71 -
SRP-275
Rev. 2.00
- 72 -
SRP-275
Rev. 2.00
- 73 -
SRP-275
4-5-2 Head circuit diagram
Rev. 2.00
- 74 -
SRP-275
4-5-3 Serial Interface Diagram (RS-232C)
Rev. 2.00
- 75 -
SRP-275
4-5-4 Parallel Interface Diagram (IEEE-1284)
Rev. 2.00
- 76 -
SRP-275
4-5-5 USB Interface Diagram (Universal Serial Bus)
Rev. 2.00
- 77 -
SRP-275
5. Disassembly and Assembly
To disassembly this printer, perform the assembly procedures described in the reverse sequence. First, the
main-assembly blocks are disassembled and divided into the sub assembly blocks, then each of the
individual blocks is disassembled.
When assembling the printer, check each part and its attachment position by referring to PPL(Product Parts
List).
5-1 SMP715 Printer mechanism unit Sub-assembly
5-1-1 Frame-main caulking assy
Part name
① Frame-main
② Shaft-R/F idle
③ Shaft-gear pulley
④ Shaft-reduction A/C -2ea.
⑤ Shaft-ribbon frame L
⑥ Shaft-ribbon frame R
⑦ Shaft-ribbon feed
⑧ Shaft-lever_CC
Assembly procedure
1. Caulk ② Shaft-R/F idle, ③ Shaft-gear pulley, two ④ Shaftreduction A/C and ⑦ Shaft-ribbon feed on ① Frame-main.
2. Caulk ⑤ Shaft-ribbon frame L and ⑧ Shaft-lever_CC on ①
Frame-main.
3. Caulk ⑥ Shaft-ribbon frame R on ① Frame-main.
③ Shaft-gear pulley
④ Shaft-reduction A/C -2EA
⑦ Shaft-ribbon feed
Shaft-R/F idle ②
⑧ Shaft-lever_CC
① Frame-main
⑤ Shaft-ribbon frame L
⑥ Shaft-ribbon frame R
5-1-2 Ribbon-feeder assy
Part name
① Ribbon-feeder
② Spring-ribbon-feeder
③ Gear-ribbon feeder
Assembly procedure
1. Grease ② Spring-ribbon-feeder with HG-31S and then insert ②
Spring-ribbon-feeder in ① Ribbon-feeder.
2. Insert ③ Gear-ribbon feeder to four hooks of ① Ribbon-feeder.
1
2
3
Rev. 2.00
- 78 -
SRP-275
5-1-3 Lever-ribbon-feeder assy
①
②
③
④
⑤
Part name
Lever-ribbon feed
Shaft-reduction B
Wave washer
Gear-re_B
Ring-e hole (ø2.5)
Assembly procedure
1. Caulk ② Shaft-reduction B on ① Lever-ribbon feed and then
grease ② Shaft-reduction B with HG-31S.
2. Insert ③ Wave washer to ② Shaft-reduction B and then grease
③ Wave washer with HG-31S.
3. Insert ④ Gear-re_B to ② Shaft-reduction B and then fasten ⑤
Ring-e hole (ø2.5) to ② Shaft-reduction B.
1
2
3
4
5
5-1-4 Lever-tension assy
①
②
③
④
Part name
Lever-tension belt
Shaft-pulley
Pulley
Washer-plain (ø2.6)
Assembly procedure
1. Caulk ② Shaft-pulley on ① Lever-tension belt and then grease
② Shaft-pulley with HG-31S.
2. Insert ③ Pulley to ② Shaft-pulley and then fasten ④ Washerplain (ø2.6) to ② Shaft-pulley.
<Check point>
Check ③ Pulley to rotate smoothly.
4
3
2
1
Rev. 2.00
- 79 -
SRP-275
5-1-5 Carriage head assy
Part name
① Head-carriage-(WI)
② Bearing-metal -2ea.
Assembly procedure
1. Insert two ② Bearing-metal into ① Head-carriage-(WI)
2
1
2
5-1-6 Head-cover assy
①
②
③
④
Part name
Cover-head
Label hot
Screw-manual (M4.0)
Ring-e hole (ø3.0)
Assembly procedure
1. Paste ② Label hot on the left bottom side of ① Cover-head.
2. Insert ③ Screw-manual (M4.0) into the right side hole of ①
Cover-head.
3. Assemble ④ Ring-e hole (ø3.0) onto the starting point of a spiral
during adhering closely to ① Cover-head.
2
3
1
4
Rev. 2.00
- 80 -
SRP-275
5-1-7 Frame basket-A assy
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑪
Part name
Frame basket
Roller holder -2ea.
Shaft-roller holder
Spring-roller holder -2ea.
Platen paper guide
Frame-holder basket-L ass’y
(Sub-assembly 5-1-9)
Frame-holder basket-R ass’y
(Sub-assembly 5-1-11)
Frame-housing cutter lower
ass’y (Sub-assembly 5-1-12)
Harness (Jumper cable)
Screw-taptite (M3×6) -4ea.
Screw-taptite (M3×4) -2ea.
Assembly procedure
1. Tighten ⑥ Frame-holder basket-L ass’y to ① Frame basket with
two ⑩ Screw-taptite (M3×6).
2. Tighten ⑨ Harness (Jumper cable) and ⑦ Frame-holder
basket-R ass’y to ① Frame basket with two ⑩ Screw-taptite
(M3×6).
3. Insert two ② Roller holder to ③ Shaft-roller holder and then
assemble two ④ Spring-roller holder to ③ Shaft-roller holder,
⑥ Frame-holder basket-L ass’y and ⑦ Frame-holder basket-R
ass’y.
4. Insert ⑤ Platen paper guide in ① Frame basket.
5. Tighten ⑧ Frame-housing cutter lower ass’y to ⑥ Frameholder basket-L ass’y and ⑦ Frame-holder basket-R ass’y with
two ⑪ Screw-taptite (M3×4).
11
10
8
10
6
11
1
4
7
10
10
5
2
4
9
3
2
Rev. 2.00
- 81 -
SRP-275
5-1-8 Frame basket-C assy
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑪
Part name
Frame basket
Roller holder -2ea.
Shaft-roller holder
Spring-roller holder -2ea.
Platen paper guide
Frame-holder basket-L ass’y
(Sub-assembly 5-1-9)
Frame-holder basket-R ass’y
(Sub-assembly 5-1-11)
Cutter lower ass’y
(Sub-assembly 5-1-13)
Harness (Jumper cable)
Screw-taptite (M3×6) -4ea.
Screw-taptite (M3×4) -2ea.
Assembly procedure
1. Tighten ⑥ Frame-holder basket-L ass’y to ① Frame basket with
two ⑩ Screw-taptite (M3×6).
2. Tighten ⑨ Harness (Jumper cable) and ⑦ Frame-holder
basket-R ass’y to ① Frame basket with two ⑩ Screw-taptite
(M3×6).
3. Insert two ② Roller holder to ③ Shaft-roller holder and then
assemble two ④ Spring-roller holder to ③ Shaft-roller holder,
⑥ Frame-holder basket-L ass’y and ⑦ Frame-holder basket-R
ass’y.
4. Insert ⑤ Platen paper guide in ① Frame basket.
5. Tighten ⑧ Cutter lower ass’y to ⑥ Frame-holder basket-L
ass’y and ⑦ Frame-holder basket-R ass’y with two ⑪ Screwtaptite (M3×4).
11
8
10
10
6
11
1
4
7
10
10
5
2
4
9
3
2
Rev. 2.00
- 82 -
SRP-275
5-1-9 Frame-holder basket-L assy
Part name
① Frame-holder basket-L
caulking ass’y
② Gear-reduction
③ Washer-plain (ø2.6)
Assembly procedure
1. Grease Shaft-reduction of ① Frame-holder basket-L caulking
ass’y with HG-31S.
2. Insert ② Gear-reduction to Shaft-reduction of ① Frame-holder
basket-L caulking ass’y and then assemble ③ Washer-plain (ø2.6).
<Check point>
Check ② Gear-reduction to rotate smoothly.
1
2
3
5-1-10 Frame-holder basket-L caulking assy
Part name
① Frame-holder basket-L
② Shaft-locking
③ Shaft-reduction
Assembly procedure
1. Caulk ② Shaft-locking and ③ Shaft-reduction on ① Frameholder basket-L.
2
1
3
5-1-11 Frame-holder basket-R caulking assy
Part name
① Frame-holder basket-R
② Shaft-locking
Assembly procedure
1. Caulk ② Shaft-locking on ① Frame-holder basket-R.
2
1
Rev. 2.00
- 83 -
SRP-275
5-1-12 Frame-housing cutter lower assy
Part name
① Frame-housing cutter lower
② Screw-taptite (M3×4) -2ea.
Assembly procedure
1. Tighten two ② Screw-taptite (M3×4) on ① Frame-housing
cutter lower.
2
2
1
5-1-13 Cutter lower assy
①
②
③
④
⑤
Part name
Cutter lower
Frame-housing cutter upper
Spring-cutter lower -2ea.
Frame-housing cutter lower
Screw-taptite (M3×4) -2ea.
Assembly procedure
1. Insert ① Cutter lower in ② Frame-housing cutter upper and
then insert two ③ Spring-cutter lower between ① Cutter lower
and ② Frame-housing cutter upper
2. Tighten ② Frame-housing cutter upper to ④ Frame-housing
cutter lower with two ⑤ Screw-taptite (M3×4).
5
2
1
3
3
4
Rev. 2.00
- 84 -
5
SRP-275
5-1-14 Frame-rotator assy
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑪
⑫
⑬
⑭
⑮
16
○
17
○
18
○
19
○
20
○
21
○
22
○
23
○
Part name
Frame rotator
Guide spring -2ea.
Frame-pivot locking-L
Frame-pivot locking-R
Screw-taptite (M3×4) -4ea.
Arm open
Screw-arm open
Spring-button
Frame-clamshell locking
Shaft-clamshell locking
Spring-locking-L
Spring-locking-R
Ring-e hole (ø2.5) -2ea.
Holder platen ass’y
(Sub-assembly I-1)
Shaft-housing platen
Frame-bar clamshell
Screw-taptite (M3×6) -2ea.
Spring-holder platen -2ea.
Shaft-rubber roller
Poly-bearing -2ea.
Ring-e hole (ø3.0) -4ea.
Gear-Feeding
Guide paper
Assembly procedure
1. Insert two ② Guide spring in two holes of ① Frame rotator.
2. Tighten ③ Frame-pivot locking-L and ④ Frame-pivot locking-R
to ① Frame rotator with each of two ⑤ Screw-taptite (M3×4).
3. Tighten ⑥ Arm open between ④ Frame-pivot locking-R and ①
Frame rotator with ⑦ Screw-arm open.
4. Assemble ⑧ Spring-button between ⑥ Arm open and ④
Frame-pivot locking-R.
5. Insert ⑨ Frame-clamshell locking between ③ Frame-pivot
locking-L and ④ Frame-pivot locking-R and then insert ⑩ Shaftclamshell locking, ⑪ Spring-locking-L and ⑫ Spring-locking-R.
And assemble two ⑬ Ring-e hole (ø2.5) to ⑩ Shaft-clamshell
locking.
6. Attach ⑭ Holder platen ass’y to ① Frame rotator and then insert
⑮ Shaft-housing platen into the hole of ① Frame rotator. And
21 Ring-e hole (ø3.0) to ⑮ Shaft-housing platen.
assemble two ○
16 Frame-bar clamshell to ⑭ Holder platen ass’y with
7. Tighten ○
17 Screw-taptite (M3×6). And assemble two ○
18 Spring-holder
○
16 Frame-bar clamshell and two hooks of ①
platen between ○
Frame rotator.
20 Poly-bearing in two holes of ① Frame rotator and
8. Insert two ○
19 Shaft-rubber roller into two holes of ○
20 Polythen insert ○
21 Ring-e hole (ø3.0) to ○
19 Shaftbearing. And assemble two ○
rubber roller.
22 Gear-Feeding to the left side of ○
19 Shaft-rubber roller.
9. Insert ○
19
23 Guide paper to ⑮ Shaft-housing platen and ○
10. Assemble ○
Shaft-rubber roller.
9
11
10
5
5
13
8
2
3
12
1
6
22
21
2
5
4
21
20
13
21
19
17
17
21
16
20
18
14
18
15
23
Rev. 2.00
- 85 -
5
7
SRP-275
5-1-15 Holder platen assy
①
②
③
④
⑤
Part name
Holder platen
Platen
Rubber platen -3ea.
Bar holder platen
Screw-taptite (M3×10) -2ea.
Assembly procedure
1. Insert three ③ Rubber platen in ② Platen.
2. Attach ② Platen to ① Holder platen.
3. Tighten ④ Bar holder platen to ① Holder platen with two ⑤
Screw-taptite (M3×10).
1
3
3
3
2
4
4
4
Rev. 2.00
- 86 -
SRP-275
5-2 SMP715 Printer mechanism unit Main-assembly
5-2-1 Main-assembly A
Part name
① Frame-main caulking ass’y
(Sub-assembly 5-1-1)
② Label sticker
③ Plate-insulation
④ Lever-change color
⑤ Assy-gear-pulley
⑥ Gear-RE_B
⑦ Washer-plain (ø2.6) -3ea.
⑧ Solenoid
⑨ Spring-solenoid
⑩ Screw-machine (M2×2.5)
⑪ Lever-tension ass’y
(Sub-assembly 5-1-4)
Assembly procedure
1. Paste ② Label sticker and ③ Plate-insulation on ① Framemain caulking ass’y.
2. Grease six shafts on ① Frame-main caulking ass’y with HG-31S.
3. Insert ④ Lever-change color into Shaft-lever_CC and then
assemble ⑦ Washer-plain (ø2.6).
4. Insert ⑤ Assy-gear-pulley and ⑥ Gear-RE_B to the Shaft-gear
pulley and Shaft-R/F idle and then assemble each of ⑦ Washerplain (ø2.6).
5. Insert ⑨ Spring-solenoid between ⑧ Solenoid and ④ Leverchange color and then tighten ⑧ Solenoid to ① Frame-main
caulking ass’y with ⑩ Screw-machine (M2×2.5).
6. Attach ⑪ Lever-tension ass’y on ① Frame-main caulking
ass’y.
8
9
11
4
7
7
7
6
5
1
10
2
3
Rev. 2.00
- 87 -
SRP-275
5-2-2 Main-assembly B
Part name
① Gear-RE_A
② Ribbon-feeder ass’y
(Sub-assembly 5-1-2)
③ Gear-RE_C
④ Cover HF gear train
⑤ Lever-ribbon-feeder ass’y
⑥ Washer-plain (ø2.6) -2ea.
⑦ PCB-head ass’y
⑧ FPC-head
⑨ FPC-30pin
⑩ Screw-taptite (M3×4) -3ea.
⑪ Spring-lever-tension
⑫ Carriage head ass’y
(Sub-assembly 5-1-5)
⑬ Belt-round
Assembly procedure
1. Insert ① Gear-RE_A, ② Ribbon-feeder ass’y and ③ GearRE_C to three shafts of Frame-main.
2. Insert ④ Cover HF gear train to two shafts.
3. Insert ⑤ Lever-ribbon-feeder ass’y to two shafts and then
assemble two ⑥ Washer-plain (ø2.6).
4. Insert ⑧ FPC-head, ⑨ FPC-30pin and the 2pin connector of
Solenoid to ⑦ PCB-head ass’y and then tighten two ⑩ Screwtaptite (M3×4).
5. Assemble ⑪ Spring-lever-tension between Lever-tension ass’y
and the hook of Frame-main.
6. Insert ⑫ Carriage head ass’y to ⑬ Belt-round and then
assemble Belt-round between Pulley and Assy-gear-pulley. And
tighten Lever-tension ass’y to Frame-main with ⑩ Screw-taptite
(M3×4).
12
13
10
8
10
6
7
5
6
11
3
10
9
4
1
2
Rev. 2.00
- 88 -
SRP-275
5-2-3 Main-assembly C
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑪
Part name
Frame basket ass’y
Screw-taptite (M3×6) -2ea.
Shaft-head_guide
Lever-ad -2ea.
Shaft-head carriage
Ring-e hole (ø3.0)
Printer-head
Screw-tapping (M3×10) -2ea.
Bracket-head-cover-L
Bracket-head-cover-R
Screw-taptite (M2.6×3) -2ea.
Assembly procedure
1. Tighten ① Frame basket ass’y on Frame-main with two ②
Screw-taptite (M3×6).
2. Insert Carriage head ass’y to ③ Shaft-head_guide and then
insert ③ Shaft-head_guide into two holes of Frame-main.
3. Insert two ④ Lever-ad to the end of ③ Shaft-head_guide and then rotate
two ④ Lever-ad downward. And oil ③ Shaft-head_guide with G948P.
4. Insert ⑤ Shaft-head carriage in two holes the Frame-main and
then assemble ⑥ Ring-e hole (ø3.0) to ⑤ Shaft-Head carriage.
5. Insert FPC-head in ⑦ Printer-head and then tighten ⑦ Printerhead on Carriage head ass’y with two ⑧ Screw-tapping
(M3×10). And grease ⑤ Shaft-head carriage and the triangle part
of Carriage head ass’y.
6. Tighten ⑨ Bracket-head-cover-L and ⑩ Bracket-head-cover-R
on Frame-main with each of ⑪ Screw-machine (M2.6×3).
2
2
1
8
8
11
7
11
9
4
10
3
6
4
5
Rev. 2.00
- 89 -
SRP-275
5-2-4 Main-assembly D
①
②
③
④
⑤
⑥
⑦
Part name
Motor-step (PF motor)
Spring-ribbon
Frame-ribbon
Ring-e hole (ø3.0) -2ea.
Motor-step (HF motor)
Screw-taptite (M3×4) -4ea.
Head-cover ass’y
Assembly procedure
1. Tighten ① Motor-step (PF motor) on Frame-holder basket-L with
two ⑥ Screw-taptite (M3×4). And insert the 4pin connector of ①
Motor-step (PF motor) to the connector of PCB-head ass’y.
2. Attach ② Spring-ribbon to the right side of ③ Frame-ribbon and
then insert ③ Frame-ribbon between Shaft-ribbon frame L and
Shaft-ribbon frame R. And fix ② Spring-ribbon to the hook of
Frame-main.
3. Assemble two ④ Ring-e hole (ø3.0) to two shafts.
4. Tighten ⑤ Motor-step (HF motor) on the bottom of Frame-main
with two ⑥ Screw-taptite (M3×4). And insert the 6pin connector of
⑤ Motor-step (HF motor) to the connector of PCB-head ass’y.
5. Tighten ⑦ Head-cover ass’y to Frame-main with Screwmanual(M4.0) of ⑦ Head-cover ass’y.
6
6
6
1
3
4
5
4
2
6
6
Rev. 2.00
- 90 -
SRP-275
5-2-5 Main-assembly E (for SMP715A type)
①
②
③
④
⑤
⑥
Part name
Frame-rotator ass’y
Shaft-pivot -2ea.
Spring-rear open -2ea.
Ring-e hole (ø5.0) -2ea.
Frame-rear cover
Screw-taptite (M3×5)
Assembly procedure
1. Attach ① Frame-rotator ass’y on Frame-main and then insert two
② Shaft-pivot and two ③ Spring-rear open. And assemble two
④ Ring-e hole (ø5.0) to two ② Shaft-pivot.
2. Tighten ⑤ Frame-rear cover on ① Frame-rotator ass’y with ⑥
Screw-taptite (M3×5).
3. Grease two Shaft-locking, the hooks of Frame-clamshell locking
and the groove of Frame-pivot locking-L/R.
6
5
2
2
1
3
4
3
4
Rev. 2.00
- 91 -
SRP-275
5-2-6 Main-assembly E (for SMP715C type)
①
②
③
④
⑤
⑥
Part name
Frame-rotator ass’y
Shaft-pivot -2ea.
Spring-rear open
Ring-e hole (ø5.0) -2ea.
Auto cutter ass’y
Screw-taptite (M3×5)
Assembly procedure
1. Attach ① Frame-rotator ass’y on Frame-main and then insert two
② Shaft-pivot and two ③ Spring-rear open. And assemble two
④ Ring-e hole (ø5.0) to two ② Shaft-pivot.
2. Tighten ⑤ Auto cutter ass’y on ① Frame-rotator ass’y with ⑥
Screw-taptite (M3×5).
3. Grease two Shaft-locking, the hooks of Frame-clamshell locking
and the groove of Frame-pivot locking-L/R.
6
5
2
2
1
3
4
3
4
Rev. 2.00
- 92 -
SRP-275
5-3 Auto cutter unit assembly
5-3-1 AC timing belt assy
Part name
① Plate-AC belt
② Holder-AC timing belt
③ Power-AC-timing belt
Assembly procedure
1. Attach ② Holder-AC timing belt to ③ Power-AC-timing belt and
then insert ① Plate-AC belt to the hole of ② Holder-AC timing
belt.
1
2
3
5-3-2 AC upper frame caulking assy
Part name
① Frame-AC upper
② Shaft-AC-worm/pulley -3ea.
Assembly procedure
1. Caulk three ② Shaft-AC-worm/pulley on ① Frame-AC upper.
2
2
1
2
Rev. 2.00
- 93 -
SRP-275
5-3-3 AC upper cutter guide assy
Part name
Guide-AC upper cutter
Washer-plain (ø2.6)
Shaft-AC-upper cutter
AC upper cutter ass’y
(Sub-assembly 5-3-4)
⑤ Cover-AC plate felt -2ea.
⑥ Felt-AC oil -2ea.
①
②
③
④
Assembly procedure
1. Insert ④ AC upper cutter ass’y in ① Guide-AC upper cutter
and then insert ③ Shaft-AC-upper cutter into ① Guide-AC
upper cutter. And assemble ② Washer-plain (ø2.6) to ③ ShaftAC-upper cutter.
2. Insert two ⑥ Felt-AC oil in ① Guide-AC upper cutter and then
assemble two ⑤ Cover-AC plate felt.
3
1
5
6
6
5
2
4
5-3-4 AC upper cutter assy
Part name
① Cutter-16.4
② Gear-AC upper cutter
③ Fastener-ring
Assembly procedure
1. Attach ① Cutter-16.4 on ② Gear-AC upper cutter and then
assemble ③ Fastener-ring.
3
1
2
Rev. 2.00
- 94 -
SRP-275
5-3-5 AC motor assy
Part name
① AC motor ass’y
(Sub-assembly 5-3-6)
② PCB-AC ass’y
(Sub-assembly 5-3-7)
Assembly procedure
1. Attach the wire of ① AC motor ass’y to ② PCB-AC ass’y and
then solder the land on ② PCB-AC ass’y bottom side.
<Check point>
After soldering, check the frozen lead and short.
1
2
5-3-6 AC motor sub assy
Part name
① Motor-DC
② Gear-AC worm
Assembly procedure
1. Insert ② Gear-AC worm to ① Motor-DC.
2
1
5-3-7 PCB-AC assy
Part name
① PCB-AC
② Photo interrupter
Assembly procedure
1. Attach ② Photo interrupter to fit the hole of ① PCB-AC and then
solder the land on ① PCB-AC bottom side.
<Check point>
After soldering, check the frozen lead and short.
1
2
Rev. 2.00
- 95 -
SRP-275
5-3-8 Main assy
Part name
① AC timing belt ass’y
(Sub-assembly 5-3-1)
② AC upper frame caulking ass’y
(Sub-assembly 5-3-2)
③ AC upper cutter guide ass’y
(Sub-assembly 5-3-3)
④ AC motor ass’y
(Sub-assembly 5-3-5)
⑤ Gear-AC worm wheel
⑥ Gear-AC gear pulley -2ea.
⑦ Shaft-AC-shaft guide -2ea.
⑧ Ring-e hole (ø3.0) -2ea.
⑨ Frame-AC lower
⑩ Screw-taptite -5ea.
⑪ Screw-tapping
⑫ Harness-AC
Assembly procedure
1. Attach ① AC timing belt ass’y to two ⑥ Gear-AC gear pulley
and then insert two ⑥ Gear-AC gear pulley to two Shaft-ACworm/pulley of ② AC upper frame caulking ass’y.
2. Insert ⑤ Gear-AC worm wheel to Shaft-AC-worm/pulley of ②
AC upper frame caulking ass’y.
3. Assemble ③ AC upper cutter guide ass’y to ① AC timing belt
ass’y and then insert two ⑦ Shaft-AC-shaft guide to ③ AC
upper cutter guide ass’y and four holes ② AC upper frame
caulking ass’y. And assemble two ⑧ Ring-e hole (ø3.0).
4. Tighten ④ AC motor ass’y to ② AC upper frame caulking ass’y
with ⑩ Screw-taptite and ⑪ Screw-tapping.
5. Tighten ⑨ Frame-AC lower to ② AC upper frame caulking
ass’y with four ⑩ Screw-taptite.
6. Insert ⑫ Harness-AC to the connector of ④ AC motor ass’y.
12
4
11
2
7
7
5
10
8
8
6
1
6
10
10
10
9
3
Rev. 2.00
10
- 96 -
SRP-275
5-4 SRP-275 Whole unit Sub-assembly
5-4-1 Cover base assy
①
②
③
④
⑤
⑥
⑦
⑧
Part name
Cover base
Frame paper control
PMO-roller paper/end -3ea.
Switch-paper near end ass’y
(Sub-assembly 5-4-2)
Screw-tapping (M2×5) -2ea.
PCB-connector sub ass’y
Screw-taptite (M3×6) -4ea.
FPC-16pin
Assembly procedure
1. Attach ② Frame paper control to ① Cover base.
2. Insert three ③ PMO-roller paper/end to ① Cover base.
3. Tighten ④ Switch-paper near end ass’y to ① Cover base with
two ⑤ Screw-tapping (M2×5).
4. Tighten ⑥ PCB-connector sub ass’y to ① Cover base with two
⑦ Screw-taptite (M3×6).
5. Insert ⑧ FPC-16pin in ⑥ PCB-connector sub ass’y.
6. Insert the connector of ④ Switch-paper near end ass’y in
connector of ⑥ PCB-connector sub ass’y.
7
7
7
6
5
5
4
7
7
2
2
2
2
1
Rev. 2.00
- 97 -
SRP-275
5-4-2 Switch-paper near end assy
Part name
① PCB-Switch-paper near end
② Switch-micro (5.9gf)
③ Harness-Switch-paper near end
Assembly procedure
1. Insert ② Switch-micro (5.9gf) to ① PCB-Switch-paper near end.
2. Solder the land on ① PCB-Switch-paper near end bottom side and
attach ③ Harness-Switch-paper near end on the land.
<Check point>
After soldering, check the frozen lead and short.
2
1
3
5-4-3 Switch-paper end assy
Part name
① PCB-Switch-paper end
② Switch-micro (2.9gf)
③ Harness-Switch-paper end
Assembly procedure
1. Insert ② Switch-micro (2.9gf) to ① PCB-Switch-paper end.
2. Solder the land on ① PCB-Switch-paper end bottom side and
attach ③ Harness-Switch-paper end on the land.
<Check point>
After soldering, check the frozen lead and short.
2
3
1
Rev. 2.00
- 98 -
SRP-275
5-4-4 Cover middle assy
Part name
① Cover middle
② PMO-roller paper/end
③ Label-logo-SAMSUNG
④ Label-logo-BIXOLON
⑤ Label-operation
⑥ Operation panel ass’y
⑦ Screw-taptite (M3×6) -2ea.
⑧ Switch-cover open ass’y
(Sub-assembly C-1)
⑨ Screw-tapping (M2×5) -2ea.
⑩ Switch-paper near end-W ass’y
(Sub-assembly C-2)
⑪ Harness (Operation panel)
Assembly procedure
1. Insert ② PMO-roller paper/end to ① Cover middle.
2. Paste ③ Label-logo-SAMSUNG on the front side of ① Cover
middle.
3. Paste ④ Label-logo-BIXOLON on the back side of ① Cover
middle.
4. Tighten ⑥ Operation panel ass’y to ① Cover middle with two ⑦
Screw-taptite (M3×6).
5. Insert ⑪ Harness (Operation panel) in ⑥ Operation panel ass’y.
6. Tighten ⑧ Switch-cover open ass’y to ① Cover middle with two
⑨ Screw-tapping (M2×5).
7. Insert ⑩ Switch-paper near end-W ass’y to ① Cover middle.
8. Align the harness of ⑧ Switch-cover open ass’y and ⑩ Switchpaper near end-W ass’y.
10
4
2
5
1
8
3
9
6
7
7
11
Rev. 2.00
- 99 -
9
SRP-275
5-4-5 Switch-cover open assy
Part name
① PCB-switch-cover open
② Switch-micro (5.9gf)
③ Harness-switch-cover open
Assembly procedure
1. Insert ② Switch-micro (5.9gf) to ① PCB-Switch-cover open.
2. Solder the land on ① PCB-Switch-cover open bottom side and
attach ③ Harness-Switch-cover open on the land.
<Check point>
After soldering, check the frozen lead and short.
2
1
3
5-4-6 Switch-paper near end -W assy
Part name
① PCB-switch-paper near end-W
② Switch-micro (5.9gf)
③ Harness-switch-paper near end
Assembly procedure
1. Insert ② Switch-micro (5.9gf) to ① PCB-Switch-paper near end-W.
2. Solder the land on ① PCB-Switch-paper near end-W bottom side
and attach ③ Harness-Switch-paper near end-W on the land.
<Check point>
After soldering, check the frozen lead and short.
1
2
3
Rev. 2.00
- 100 -
SRP-275
5-4-7 Bracket PCB assy
Part name
① Bracket PCB
② PCB-main ass’y
③ Screw-taptite (M3×6) - 3ea.
④ Foot rubber -4ea.
Rev. 2.00
Assembly procedure
1. Tighten ② PCB-main ass’y to ① Bracket PCB with three ③
Screw-taptite (M3×6).
2. Paste four ④ Foot rubber on ① Bracket PCB.
- 101 -
SRP-275
5-4-8 Serial interface assy
Part name
① I/F bracket serial
② Serial PCB ass’y
③ Nut-hexagon -2ea.
Assembly procedure
1. Tighten ② Serial PCB ass’y on ① I/F bracket serial with two ③
Nut-hexagon.
2
1
3
3
5-4-9 cover front-A assy
Part name
① Cover front-A
② Label-warning cover
Assembly procedure
1. Paste the ② Label-warning cover on the inside ① Cover front-A.
(The SRP-275C type uses Cover front instead of ① Cover front-A.)
1
2
Rev. 2.00
- 102 -
SRP-275
5-5 SRP-275 Whole unit Main-assembly
5-5-1 Main-assembly A (for SRP-275A type)
Part name
① SMP715A printer mechanism ass’y
② Rubber-damper
③ Cover base ass’y
④ Screw-taptite (M3×12) -4ea.
Assembly procedure
1. Insert four ② Rubber-damper to a half circle groove of ①
SMP715A printer mechanism ass’y.
2. Tighten ① SMP715A printer mechanism ass’y on the boss of ③
Cover base ass’y with four ④ Screw-taptite (M3×12).
3. Insert Harness-jumper cable to a square hole of ③ Cover base.
4
2
4
1
2
4
4
Harness-jumper cable
2
2
3
Rev. 2.00
- 103 -
SRP-275
Part name
⑤ Switch-paper end ass’y
⑥ Screw-tapping (M2×5) -2ea.
Assembly procedure
4. Tighten ⑤ Switch-paper end ass’y on the bottom of Frame paper
with two ⑥ Screw-tapping (M2×5).
6
6
5
Rev. 2.00
- 104 -
SRP-275
5-5-2 Main-assembly A (for SRP-275C type)
Part name
① SMP715C printer mechanism ass’y
② Rubber-damper
③ Cover base
④ Screw-taptite (M3×12) -4ea.
Assembly procedure
1. Insert four ② Rubber-damper to a half circle groove of ①
SMP715C printer mechanism ass’y.
2. Tighten ① SMP715C printer mechanism ass’y on the boss of ③
Cover base with four ④ Screw-taptite (M3×12).
3. Insert Harness-AC and Harness-jumper cable to a square hole of
③ Cover base.
4
2
4
1
2
Harness-AC
4
4
Harness-jumper cable
2
2
3
Rev. 2.00
- 105 -
SRP-275
Part name
⑤ Switch-paper end ass’y
⑥ Screw-tapping (M2×5) -2ea.
Assembly procedure
4. Insert the 5pin connector of Harness-AC in the connector of PCBconnector sub ass’y.
5. Tighten ⑤ Switch-paper end ass’y on the bottom of Frame paper
with two ⑥ Screw-tapping (M2×5).
6
6
5
Harness-AC
Rev. 2.00
- 106 -
SRP-275
5-5-3 Main-assembly B
Part name
① Cover middle
② Screw-taptite (M3×10) -4ea.
Assembly procedure
1. Tighten ① Cover middle on Cover base with four ② Screw-taptite
(M3×10).
2. Insert Harness-switch-rear cover open and Harness-switchpaper near end-W to a square hole of Cover base.
2
2
2
2
1
Harness-Switch-rear cover open
Rev. 2.00
- 107 -
Harness-Switch-paper near end-W
SRP-275
Part name
Assembly procedure
3. Insert the 2pin connector of Switch-rear cover open ass’y and the
2pin connector of Switch-paper near end-W ass’y in the
connectors of PCB-connector sub ass’y.
Harness-Switch-paper near end-W
Harness-Switch-rear cover open
Rev. 2.00
- 108 -
SRP-275
5-5-4 Main-assembly C
Part name
① Bracket PCB ass’y
(Sub-assembly D)
② Screw-taptite (M3×6)
③ Screw-taptite (M3×10) -3ea.
④ Harness-power
Rev. 2.00
Assembly procedure
1. Tighten Harness-jumper cable to the side hole of ① Bracket PCB
ass’y with ② Screw-taptite (M3×6).
2. Insert FPC-connector sub (16pin) to ① Bracket PCB ass’y and
then tighten ① Bracket PCB ass’y to Cover base with three ③
Screw-taptite (M3×10).
3. Insert ④ Harness-power into the right front side hole of Cover base.
4. Insert the 2pin connector of ④ Harness-power, the 6pin connector
of Harness-operation panel and the 2pin connector of Harnesspower in three connectors PCB-main ass’y.
- 109 -
SRP-275
5-5-5 Main-assembly D
Part name
① Frame-base
② Frame-cover DIP
③ Serial interface ass’y
(Sub-assembly E)
Rev. 2.00
Assembly procedure
1. Tighten ① Frame-base on Bracket PCB ass’y with four ⑥ Screwtaptite (M3×6).
2. Tighten ② Frame-cover DIP on ① Frame-base with ⑥ Screwtaptite (M3×6).
3. Tighten ③ Serial interface ass’y to PCB-main ass’y with two ⑥
Screw-taptite (M3×6).
- 110 -
SRP-275
Part name
④ Button open
⑤ Cover rear
⑥ Screw-taptite (M3×6) -9ea
⑦ Cover front-A ass’y
(Sub-assembly F)
⑧ Label-logo-BIXOLON
⑨ Label-rating
Assembly procedure
4. Insert ④ Button open to ⑤ Cover rear and then tighten ⑤ Cover
rear on Frame-rotator ass’y with two ⑥ Screw-taptite (M3×6).
5. Assemble ⑦ Cover front-A ass’y to Cover base.
(The SRP-275C type uses Cover front ass’y instead of ⑦ Cover frontA ass’y.)
6. Paste ⑦ Label-logo-BIXOLON on the center of ⑦ Cover front-A
ass’y.
7. Paste ⑨ Label-rating on ① Frame-base.
6
5
4
3
5
7
8
Rev. 2.00
- 111 -
SRP-275
6. Adjustments and Maintenance
6-1 Adjustment
When assembling this printer, be sure to refer to the required adjustment procedure. To ensure normal
operation of the printer after disassembly or replacement of a Component for maintenance or repair. Be sure
to perform along to the required method.
6-1-1 Adjustment of Head gap
Adjustment step and description points
In Adjustment
1) Move the Printer-head to L side.
2) Insert the thickness gauge between Printer-head and platen, then
Appropriate gap: 0.40~0.50mm
rotate the AD-lever L and adjust the gap.
Gap 0.40~0.50
Holder platen
In order to make the gap narrow
(wide), turn AD-lever to mark
‘-(+)’
Platen
Printer-head
If gap is not correct, repeat once
more.
Frame-main
3) Move the Printer-head then check if the proper gap from R side
center has been achieved.
4) If head gap is not proper, adjust head gap by rotating AD-lever R.
6-1-2 Replacement of Printer-head
Follow below steps for replacing Printer-head.
1) Loosen the Frame-ribbon.
2) Disassemble the Printer-head from the Carriage head ass’y and take out the FPC-head from the
connector of PCB ass’y.
3) Replace the Printer-head and assemble, according to the order of Sub-assembly E.
4) After assembling, adjust the gap as above “Adjustment” indicates.
5) Assemble the Frame-ribbon.
Rev. 2.00
- 112 -
SRP-275
6-2 Maintenance
To ensure the maintenance of this printer at its initial performance level throughout a long product life as well
as preventing potential troubles, be sure to perform maintenance and management according to the points
described in the following subsections.
6-2-1 Cleaning
• Eliminating dirt or strains
- Wipe off the soiled sections using alcohol or benzene.
- Eliminating dust, scraps, and other foreign particles.
- Use a vacuum cleaner to carefully draw out all foreign particles from every part of the printer.
NOTES
• Never use thinner, tricholyene nor ketone solvents as such use may deteriorate or damage the plastic
parts.
• Check the lubricant each cleaned section and perform remaining lubrication as required.
(See subsection 4.2.3, "Lubrication points" )
6-2-2 Inspection
The maintenance and check-up procedures for this printer are grouped into two types.
1) Daily checks that can be easily performed by the operator of the printer during the course of daily work.
2) Periodic checks that can be performed only by persons having a through understanding of the printer
mechanisms. These maintenance and check procedures should be implemented according to the
technical level of the person conducting them.
• Daily check
The printer and printer operation are checked to see if the printer is being operated in the proper manner and
always being maintained in optimum condition. If any unsatisfactory points are discovered. They should be
replaced.
1) Check that the Ribbon Cassette is securely installed properly.
2) Check that the Ribbon Cassette in use conforms to the SPECIFICATIONS. (RRC-275 or compatible)
3) Check the ribbon for bending, twisting or damage. Replace the Ribbon Cassette if it is affecting print
quality.
4) Check that the paper in use conforms to that described in the SPECIFICATIONS.
• Periodic check
After every 6 months, the printer parts should be checked for wear. cleanliness, deformation, remaining
lubrication, installation status, etc, If any unsatisfactory points are discovered, they should be replaced.
1) Check the printer interior for adhesion of paper dust, scraps and other foreign particles, or clean out any
adhered particles with a vacuum cleaner (paying special attention to dirt in the vicinity of the detectors.)
2) Check all the springs for deformation, or replacing any deformed springs.
3) Check the gap between Head unit and Holder platen ass`y. If there is a malfunction, perform repair
according to "4.4 Adjustment".
4) Check the lubricant and adhesive status of all applications points, applying lubricant or adhesive as
required according to "4.2 Lubricants and Adhesive Application"
5) Check if printing. paper feeding. ribbon feeding and ribbon shifting are normal. If not, perform repair
according to "Chapter 5 Troubleshooting”.
6) Observe all of the functions and check for malfunctions due to wear or deformation of parts, paper jam. etc.
If there is a malfunction, perform repair according to "Chapter 5 Troubleshooting".
Rev. 2.00
- 113 -
SRP-275
6-3 Lubricants and adhesive application
Lubrication and application adhesive plays an important role in maintaining this printer at its initial
performance level, throughout a long product life as well as preventing potential troubles. Make sure to apply
the specified lubricants or adhesive in the appropriate amounts at the specified intervals .
6-3-1 Lubricant requirements
Before applying the lubricants during an assembly or disassembly procedure, be sure to first thoroughly
clean the part to be lubricated. For details on lubrication see "4.2.3 Lubrication points" and "4.2.2 Lubricant
types".
• Lubrication Classes
Concerning the lubrication interval, lubrication should be performed periodically according to the lubrication
classes described below. If lubrication becomes deficient due to cleaning, disassembly or parts
replacement, be sure to lubricate the required part regardless of the lubrication interval.
- A : Lubrication every 6 months.
- B : Lubrication after on overhaul or every 1 million lines
6-3-2 Lubricant types
The type of oil used greatly influences performance and durability, and special attention is required to its low
temperature characteristic. Consequently, the oils to be used with this printer are specified by us on the
basis of the result of the thorough analyses of technical data for many types of oils and various experiments.
2 types of oils to be used with this printer are:HG-31S, G 948P
6-3-3 Lubrication points
No
1
2
3
4
5
6
7
Lubrication point
Outer periphery of shaft hold roller
Contact point between cam of head carriage and ribbon frame
Contact point between shaft ribbon frame and lever color change
Contact point between spring ribbon feeder and ribbon feeder
Outer periphery of shaft head carriage
Outer periphery of all gears
Outer periphery of shaft head guide
Oil type
HG-31S
HG-31S
HG-31S
HG-31S
G948P
HG-31S
HG-31S
• Precautions on lubrication
Never apply lubricant to Gear Ratchet or outer periphery of Rubber Roller. If lubricant has accidentally been
applied to these parts, clean them with alcohol.
6-3-4 Adhesive application requirements
To prevent from screws getting loose by various vibration while transporting the printer, adhesive should be
applied after tightening screws. When performing disassembly or parts replacement, be sure to apply
adhesive according to "4.2.6 Adhesive application points".
6-3-5 Adhesive types
The adhesive type for use with this printer : Screwlock
6-3-6 Adhesive application points
No
12
Adhesive application point
Volume resistance adjustment of main PCB
Rev. 2.00
- 114 -
Adhesive Type
Screwlock
SRP-275
6-4 Tools, lubricants and adhesives
6-4-1 List of tools
No
1
2
3
4
5
6
7
8
9
10
11
Tool designation
Availability
○
○
○
○
○
○
○
○
○
○
Brush #1
Brush #2
Cleaning brush
Screwdriver (+) No.2
Tweezers
Round pliers
Diagonal cutting nipper
Electric Soldering iron
Thickness gauge
ET holder #2.5
ET holder #3
6-4-2 List of lubricants and adhesives
Item
Description
Rev. 2.00
Oil
CALTEX REGAL R/D #68, 948P
- 115 -
Grease
HG-31S
Adhesive
Screwlock
SRP-275
7. Troubleshooting
Use the following to troubleshoot and repair the printer:
• Troubleshooting flow chart
When the source of the problem is not clear, use the flowchart to find and replace a defective component.
• Troubleshooting tables
Follow the steps outlined in these tables to repair a defect whose symptoms are known.
7-1 Troubleshooting flow chart
If the source of a problem is not clear, use the flowchart below to find and replace a defective component.
Normally, servicing should be performed by component replacement. Repairs of the PCBs and other
components should be performed only by technicians.
Start
Power On
Is POWER LED lit?
NO
A
YES
Is PAPER OUT
LED lit?
YES
B
NO
Is ERROR LED blink?
YES
C
NO
Is ERROR LED lit?
YES
D
NO
Execute self test
Is self test
normal?
NO
E
YES
Host sends print data
Is print out normal?
NO
F
YES
End
Rev. 2.00
- 116 -
SRP-275
A. POWER LED does not light
A
Is AC adaptor & power cord
connected properly?
NO
Connect AC adaptor & power cord
properly.
YES
OK?
NO
YES
END
Does AC adaptor have
proper output voltage rating?
(approx. +24V)
NO
Replace AC adaptor.
OK?
NO
YES
YES
END
Has fuse FU1 on
main PCB blown?
YES
Replace fuse FU1
OK?
NO
NO
YES
END
Is POWER LED
continuity normal?
NO
Replace Operation panel ass’y
YES
NO
YES
Replace PCB-main ass’y
END
END
Rev. 2.00
OK?
- 117 -
SRP-275
B. PAPER LED is lit
B
Turn power off, then once again
OK?
YES
END
NO
Is paper roll in
paper near-end condition or
not inserted?
NO
Replace or insert paper roll
YES
OK?
NO
YES
END
Is paper-end switch,
paper near-end switch
continuity normal?
YES
NO
Replace Switch-paper-near end ass’y
or Switch-paper-end ass’y
OK?
NO
YES
END
Replace PCB-main ass’y
END
Rev. 2.00
- 118 -
SRP-275
C. ERROR LED is blink
C
PATTERN A
PATTERN B
Blinking
pattern A ?
YES
Replace PCB-AC ass’y (home position sensor)
OK?
NO
NO
YES
END
Blinking
pattern B ?
YES
Replace PCB-AC ass’y (home position sensor)
NO
OK?
NO
YES
Replace PCB-main ass’y
OK?
END
YES
NO
END
Replace printer mechanismass’y (SMP715)
END
Rev. 2.00
- 119 -
SRP-275
D. ERROR LED is lit
D
Turn power off, then once again
OK?
YES
END
NO
Is rear cover
closed properly?
YES
Replace Switch-rear cover open ass’y
NO
Close rear cover properly
NO
OK?
YES
Replace PCB-main ass’y
END
END
Rev. 2.00
- 120 -
SRP-275
E. Self test is not normal
E
Does not printer
operate at all?
YES
Is output voltage of
regulator on PCB-main
within SPEC?(*1)
NO
Replace PCB-main ass’y
Printing is carried out, but print
quality is deficient or paper feeding is
not normal
YES
Replace printer
mechanism ass’y
Replace printer
mechanism ass’y
OK?
YES
NO
END
Replace PCB-main ass’y
END
(*1)
Rev. 2.00
NO
OK?
YES
END
END
Check point
+terminal of C51
+terminal of C55
NO
Rating
+24V
+5V
- 121 -
SRP-275
F. Data from host is not printed normally
F
Send data from host to printer
OK?
YES
END
NO
Are interface
parameters set to
identical values at host and
printer?
NO
Make settings identical
OK?
NO
YES
YES
END
Does interface cable
match specifications?
NO
Replace with a proper cable
YES
NO
OK?
Replace interface PCB ass’y
YES
END
OK?
YES
END
NO
Is the interface
wire broken?
YES
Replace the interface cable
NO
OK?
NO
YES
Replace printer mechanism ass’y
END
OK?
YES
NO
Check the host
Rev. 2.00
END
- 122 -
SRP-275
7-2 Troubleshooting flow tables
If a problem that can be verified by visual examination has occurred, use the tables below to determine the
cause and perform repairs.
There are four tables, divided by symptom category :
• Initialization Problems
• Printing Quality Problems
• Printer Mechanism Problems
• Auto cutter Mechanism Problems
The tables contains the following columns :
• Problem
This is the symptom that can be verified
• Problem Causes
This is a listing of one or several possible causes that should be examined.
• Level
- Level A
The problem can be corrected by persons who are familiar with the printer and have general knowledge,
but special technical skills are not required.
- Level B
The problem requires thorough knowledge and familiarity with the printer as well as technical skills and
experience.
• Checkpoint
These are one or more areas in the printer that should be checked.
• Action
These are the steps to correct the problem. If the problem persists after taking these steps, check the other possible
causes listed.
Rev. 2.00
- 123 -
SRP-275
7-2-1 Initialization problems
Problem
Probable Cause
Level
Output voltage of internal AC adaptor
or PCB-main ass’y failure (Abnormal B
regulator circuit)
Printer does
not operate
at all
PCB-main ass’y failure
(Abnormal regulator circuit)
B
Carriage
vibrates,
emits an
unusual
sound, and
causes an
error state at
power on
Carriage
head ass’y
first moves
normally, but
then hits the
left side of
the print
frame,
making an
unusual
sound
Wire break or bad solder point between
B
connector and HF motor terminals
Wire disconnect between HF motor
B
connector and PCB-head ass’y
FPC(30pin) is failure or disconnected
between PCB-head ass’y and PCB- B
main ass’y
B
Home position sensor failure
B
Wear, damage, or contamination of
carriage drive gears
HF motor failure
A
A
Incorrect DIP S/W setting
Replace
PCB-main ass’y
Make sure the connection
Make sure the connection
and replace the FPC
Replace the HF motor, if is
does not rotate properly
Replace
PCB-head ass’y
Replace any damaged
gears
Remove any dirt deposits
or foreign matter
Replace
Ribbon cassette
Check if Bracket-head-coverMake it vertically
L/R is slanted to the inside
Check input signal to HF motor
drive terminal of J3 with an
oscilloscope
Check
continuity
between
respective terminals
Check the solder condition
Check the input voltage (24V
±2V)
between
the
motor
terminals of the connector using
a DVM or oscilloscope
B
B
B
B
Replace
PCB-main ass’y
Replace the terminal
Resolder as required
Inspect and repair
adaptor circuit
AC
B
Check the connected condition Make sure the connection
of FPC and FPC failure
and replace FPC
B
Above six checks have been
Replace HF motor
passed
FPC(16pin) is failure or disconnected
between PCB-connector sub ass’y B
and PCB-main ass’y
Auto cutter home position sensor
failure
Rev. 2.00
Check for connected condition
of FPC and FPC
failure
Check if motor operation is
proper without load
Use an oscilloscope to check the
sensor output signal when
Carriage head ass’y passes the
sensor
Check gears for wear and
damage
Check for dirt deposits or other
foreign matter
Check for rotated load of ribbon
cassette knob
Head is bumped against BracketB
head-cover-L/R
Wire break or bad solder point between
HF motor
connector and HF motor terminals
does not
operate at all
when power Defective power input to HF motor
is turned on,
and causes
an error state FPC(30pin) is failure or disconnected
between PCB-head ass’y and PCBmain ass’y
Auto cutter
does not
operate at all
Check connected condition
Ribbon cassette’s abnormal operation B
PCB-main ass’y failure
(HF motor drive signal failure)
Replace external
Power supply unit or PCBmain ass’y or fuse
Check clock generator (U10)
A
Defective HF motor
Action
Replace
PCB-main ass’y
Replace
Check input at pin 26 of IC(U12)
PCB-main ass’y
Check input at pin 14,30,31 of Replace
IC(U15)
PCB-main ass’y
Check Lever-tension ass’y If it Reassemble
Lever-tension ass’y
is assembled properly
Check
continuity
between
Replace the terminal
respective terminals
Check solder condition
Resolder as required
PCB-main ass’y failure
B
(Abnormal CPU clock generator circuit)
PCB-main ass’y failure
B
(Program ROM selection failure)
PCB-main ass’y failure
B
(RAM selection failure)
Excessive belt tension
Checkpoint
Check 24V input voltage at J11
and output voltage of DC
+5V(C55)/24V control circuit and
fuse(FU1)
Check voltage level at RESET
terminal (pin 129) of CPU, U1
(4.75~5.25V)
Check the connected condition Make sure the connection
of FPC and FPC failure
and replace FPC
A
B
Check the DIP Switch 1-3 setting
is ON
Use an oscilloscope to check the
sensor output signal when cutter
blade passes the sensor
- 124 -
Correct DIP Switch 1-3
setting
Replace
PCB-AC ass’y
SRP-275
7-2-2 Printing quality problems
Problem
HF motor
rotates
normally but
no dot printing
is performed
A certain dot
does not print
Character
width changes
irregularly
Print is very
faint
Rev. 2.00
Probable Cause
Level
FPC-head connector is disconnected
with PCB-head ass’y and Printerhead
B
Broken common lead of FPC-head
B
FPC(30pin) between the PCB-head
ass’y and PCB-main ass’y is broken
B
Positional
relationship
Printer-head and Platen
B
between
Checkpoint
Check if the FPC-head is
properly inserted into its
connector of head and its
board
Check
the
conductivity
between the common lead of
FPC-head
and
other
terminals
Check the conductivity of the
FPC(30pin)
Check if the gap between the
platen and the pin of head is
correct value : 0.40±0.05mm
Check Ribbon cassette’s
existence
Check firing input pulse with
an oscilloscope
Check the conductivity of
lead of FPC-head
Check if the gap between the
platen and the pin of head is
correct value : 0.40±0.05mm
Action
If is not, securely
reinsert the FPChead
Replace the HEAD
unit, if there is no
conductivity
Replace the FPC
(30pin) if there is no
conductivity
Correct the gap
Insert
Ribbon cassette
Replace
PCB-main ass’y
Ribbon cassette is absent
A
Input pulse irregularity
B
Damaged lead in FPC-head
B
Positional relationship between the
head and the platen
B
FPC(30pin) is failure or disconnected
between PCB-head ass’y and PCBmain ass’y
B
Check
the connected
condition of FPC and FPC
failure
Make sure the
connection and
replace the FPC
Defective Printer-head
B
Check head response to
command with oscilloscope
Belt tension is loose
B
Check Spring-lever-tension
for deformation
Carriage drive area contamination
B
Carriage drive parts wear or damage
B
Ribbon cassette is exhausted
A
Head gap is not correct between
head and platen
B
Check the gap
Defective Printer-head
B
Check head response to
command with oscilloscope
Replace
Printer-head
Replace or
reassemble Springlever-tension
Remove any dirt
deposits or foreign
matter
Replace defective
gear
Replace
Ribbon cassette
If incorrect, performed
repair with reference
Replace
Printer-head
- 125 -
Check gears and pulleys for
dirt deposits or other foreign
matter
Check if there are defective
parts among gears
Check for ink of ribbon
cassette
Replace FPC-head
If incorrect,
performed repair with
reference
SRP-275
7-2-3 Printer mechanism problems
Problem
Probable Cause
Level
Checkpoint
B
Check the width, length and
thickness of the paper
A
Check paper roll path for
obstacles
B
Check for paper jam
Defective paper supply
Occurrence of paper jam
Paper roll is
not fed or
Paper roll
feed pitch is
irregular
No detection
of paper near
end, paper
end and rear
cover open
Ribbon feed
mechanism
does not feed
No working on
ribbon shifting
Rear cover
does not
closed
Different
character than
input code is
printed
Rev. 2.00
Spring-holder roller is
unhooked or damaged
In proper connection between PF
motor connector and PCB-head
ass’y
B
B
Check to see if the spring is
unhooked or damaged
Check connected condition
of motor connector into PCBhead ass’y
Action
Use paper roll that
corresponds to
specifications
Remove any
obstacles from paper
path
Open the cover and
remove paper jam
Hook Spring-holder
roller or replace
Make PF motor
connector into PCBhead ass’y surely
If there is wear or
damage, replace the
gears
If the rubber is worn,
replace Shaft-rubber
roller
Wear or damage of teeth of Gear
feeding or Gear reduction
B
Check the gears for wear or
damage
Wear or damage of rubber of Shaftrubber roller
B
Check the surface of the
rubber for wear or damage
PCB-main ass’y failure
(PF motor drive signal failure)
B
Check input signal to paper
feed motor drive terminals of
J4 with an oscilloscope
Replace
PCB-main ass’y
Switch-micro failure or paper dust
around switch
A
Check switch function or
dust around switch
Replace
Switch ass’y or
remove dust
The ratchet of Ribbon cassette is
damaged or worn out
B
Wear or damage of the teeth of the
gears
B
Lever-change color does not come
back to normal position
B
Check whether the ratchet of
Ribbon
cassette
is
damaged or worn out
Check Ribbon feeder ass’y
and Gear-RE_A, B, C for
wear of damage
Check
if
Lever-change
color position while solenoid
on and off
If there is wear or
damage, replace it
Remove dust around
the gear train, Shafthead_guide and
Shaft-head carriage
Replace it if damaged
or worn out
Replace Solenoid
Carriage head ass’y does not
function to shift Ribbon cassette
B
Check if head carriage
operation when it pushes the
Frame-ribbon
Spring-locking-L/R is absent or not
hooked
B
Check if Spring-lockingL/R’s existence and its
position
Reassemble it
Check DIP Switch settings
Set DIP Switches
correctly (See Section
2.2.2 Setting the DIP
Switches)
Communication condition such as
transmission speed not set correctly
A
Communication cable failure
A
Command problem
B
Interface failure (Receive/driver IC
failure)
B
- 126 -
Check to see if the cable RS232C null modem cable, and
check its continuity
Check data sent from host
with hexadecimal dumping
function
Above three checks have
been passed
Replace cable
Correct the
application program
Replace interface
SRP-275
7-2-4 Auto cut mechanism problems
Problem
Probable Cause
Level
Paper does
not cut despite
normal
operation of
Motor-DC
No intersection between Cutter
and Cutter lower
B
Check for intersection
Reassemble
Auto cutter ass’y or
Cutter lower ass’y
Defective
soldering
between
Motor-DC and connector wire
Defective connection between
connector of Auto cutter ass’y
and PCB-AC ass’y
B
Check soldering condition
Resolder as required
Motor-DC
does not rotate
B
Check for
connector
Rev. 2.00
- 127 -
Checkpoint
connection
Action
of
Make sure connection
of connector
SRP-275
8. Appendix (Mechanism operating principles)
The printer mechanism of the SRP-275 consists of the following component mechanisms:
• Transport mechanism
• Printing mechanism
• Detection mechanism
• Auto cutter mechanism
• Easy paper loading mechanism
These components are described in detail in the following sections.
8-1 Transport mechanism
8-1-1 Head feeding system
This printer is using DC24V PM Type Stepping motor. As shown in figure, the motor section consists of the
motor, motor speed control IC, motor drive/brake circuit and motor speed interface.
When the HF(Head Feed) motor is driven and the HF motor pinion is moved in the direction of arrow B, the
rotational power is conveyed to the belt drive pulley, then the belt. Next the Carriage head ass’y, which is
fixed to the belt, moved in the direction of arrow B.
When the HF motor pinion is rotated in the direction of arrow A, the Carriage head ass’y is moved in the
direction of arrow A.
Belt-round
Pinion-HF-motor
A
B
A
B
A
B
Head
Pulley
Ass’y-gear-pulley
Carriage head ass’y
VCC_24V
VCC_24V
INA
HEAD_PAn
5
INA
HEAD_PB
17
INB
HEAD_PBn
16
INB
HEAD_A
VCCB
6
VCCA
7
U1
HEAD_PA
C2
100n 1608
12
C1
100n 1608
SLA7024M
C8
470p 1608
C9
470p 1608
C7
1n 1608
1n 1608
R6
1 1W 6432
VCC_5V
R9
R11
HEAD_HOLD
1K 1608
Rev. 2.00
R8
680 1% 1608
27 1% 1608
Q1
MMBT2222ALT1/ SOT23
R10
100 1% 1608
- 128 -
OUTA
8
OUTB
11
OUTB
18
SENSEB
Vref_B
GNDA
GNDB
C6
R4
510 1% 1608
1
C4
22p 1608
HEAD_An
HEAD_B
C5
22p 1608
10
3
R3
47K 1608
14
Td_B
4
15
13
VCC_5V
9
Td_A
Vref_A
R2
47K 1608
2
SENSEA
VCC_5V
OUTA
R5
510 1% 1608
R7
1 1W 6432
HEAD_Bn
SRP-275
8-1-2 Paper feeding system
Paper feeding is performed by conveying the PF(Paper Feed) motor’s rotational power from the PF motor
pinion through the Gear reduction and Gear feeding.
Since the Shaft-rubber roller and Roller holder are pressed together, paper advances to the top of the
Rotator ass’y because of the friction between the rubber of the Shaft-rubber roller and the Roller holder.
Shaft-rubber roller
Paper
Pinion PF motor
Roller holder
Gear reduction
Gear feeding
Shaft-roller holder
LF_Bn
LF_B
C50
820p 1608
R66
56K 1608
C49
820p 1608
R65
PHA
Vref
11
8
[4] LF_PHB
1K 1608
1
MB
TEA3718
I0
I1
[4] LF_IB1
[4] LF_IB0
R64
10K 1% 1608
R61
510 1% 1608
[4] LF_PHA
[4] LF_IA0
VCC_5V
TP160
9
U17
6
[4] LF_IA1
R67
0.5 1/2W DIP
C48
22p 1608
15
MA
C45
100n 1608
VCC_5V
C44
100n 1608
VCC_24V
C43
820p 1608
R59
56K 1608
7
Vref
PHA
8
11
C42
820p 1608
R58
TEA3718
I0
I1
VCC
9
1K 1608
MB
1
R60
0.5 1/2W DIP
C40
22p 1608
15
MA
C38
100n 1608
PT
2
U15
6
3
14
7
VCC
GND1
GND2
GND3
GND4
4
5
12
13
VM1
VM2
C37
100n 1608
PT
2
COMP
10
VCC_24V
GND1
GND2
GND3
GND4
4
5
12
13
3
14
RS
16
VCC_5V
COMP
10
VM1
VM2
- 129 -
RS
Rev. 2.00
16
LF_A
LF_An
As shown in figure, paper feeding system consists of Shaft-rubber roller, Roller holder, Motor-step, Gear
reduction and Gear feeding. The paper feeding operation can be selected by controlling the Motor-step.
Paper feeding is made as follows; As Motor-step set turning by electric signal, Shaft-rubber roller comes
into turning, passing Gear reduction. For Shaft-roller holder is pressed to Roller holder by Spring-roller
holder, paper is feed by friction. Pitch is 1/144″.
SRP-275
8-1-3 Ribbon feeding system
When the HF motor rotates CCW(CounterClockWise) and the HF motor pinion rotates in the direction of
arrow A, Gear-RE(REduction)_B, Gear-RE_A and Gear-RE_B' rotate in the directions of arrows B, and C,
D respectively. This causes the Lever ribbon feeder ass’y to move in the direction of arrow E, rotating
round the Shaft-reduction A/C in the center, until the Gear-RE_B' goes in with the Gear-RE_C.
Since the Gear-RE_C and the Ribbon feeder ass’y are always engaged, the Ribbon feeder ass’y rotates
in the direction of arrow G.
When the HF motor rotates in the reverse direction and the HF motor pinion rotates in the direction of arrow
a, the Lever ribbon feeder ass’y moves in the direction of arrow e, disengaging the Gear-RE_B' from the
Gear-RE_C.
Therefore, the Ribbon feeder ass’y rotates in the direction of arrow G only when the HF motor rotates CCW.
Then the Ribbon feeder and ribbon hold rollers in the Ribbon cassette, which are engaged with the
Ribbon feeder ass’y, rotate and the ribbon is fed.
Lever ribbon feeder ass’y
Ribbon feeder ass’y
Pinion HF motor
Shaft-reduction A/C
a
F
E
A
e
C
G
D
B
Gear-RE_C
Gear-RE_B
Gear-RE_A
Gear-RE_B΄
8-1-4 Color changing system
Color change system consists of Ribbon feeding system in section 8-1-3 and Ribbon shifting system in
section 8-1-4-1
8-1-4-1 Ribbon shifting system
Shifting system of Ribbon consisted of Carriage head ass’y, Frame-ribbon, Lever-change color,
Solenoid and Spring-solenoid as show in figure.
Ribbon shifting action is as follows.
When you’d like to change from black color to red color, you should move the Carriage head ass’y. As the
HF motor rotates CW(ClockWise), Carriage head ass’y moves from left to right. As Carriage head ass’y
moves to right, it dashes against Frame-ribbon(A), and Frame-ribbon is in shift up(B), and Lever-change
color is turn by Spring-solenoid(C). And then printing color is printed by red.
At this moment, if you’d like to change from red color to black color, you should control Solenoid. If not
energized in Solenoid, plunger are not moved, and so Lever-change color does not turn, and Frame-ribbon
is not in shift down. As Solenoid moves energized, and plunger pulls and Lever-change color turns(D), and
Frame-ribbon is in shift down(E). And then printing color is printed by black.
Rev. 2.00
- 130 -
SRP-275
Carriage head ass'y
C
A
Lever-change color
B
Frame-ribbon
MOVING RIBBON UPWARD
HEAD CARRIAGE SHIFT(BLACK-->RED)
Lever-change color
E
Frame-ribbon
Solenoid
D
MOVING RIBBON DOWNWARD
SOLENOID ON(RED-->BLACK)
8-2 Printing mechanism
When the specified print head drive pulse is input to the drive coil, the iron core is magnetized, and the
actuating plate is pulled in the direction of arrow A. This action pushed the wire toward the Platen. When the
wire strikes the ink ribbon and paper against the Platen(*1), a single dot is printed.
When the energizing of the drive coil is completed, the wire and actuating plate are returned to the standby
position by the wire return spring and actuating plate spring.
NOTES
(*1) The “Platen” is the portion of the base paper feed being struck by the wires during printing.
Ink ribbon
Paper roll
Wire
Plate
Spring
B
Platen
Wire guide
A
Iron core
Driver coil
Rev. 2.00
- 131 -
SRP-275
8-3 Detection mechanism
Each of the detection component mechanism in the SRP-275 and their corresponding function are listed
below. Detailed explanations of each of the detection mechanism are provided in this section.
Detection mechanism
Home position
Paper near end
Paper end
Rear cover open
Auto cutter home position
Function
Initial setting of SRP-275
Detection of presence/a little presence of paper roll
Detection of presence/absence of paper roll
Detection of the rear cover open/close
Initial setting of Auto cutter
Auto cutter
Home position sensor
Switch-paper near end-W
Switch-cover rear open
Switch-paper near end
Cover middle
Switch-paper end
Cover base
Home position sensor
8-3-1 Home position detection mechanism
The home position detection mechanism consists of the detection plate at the left side of the Carriage head
ass’y and the home position sensor at the left side of the Frame-main. It determines the home position,
identifies the head carriage position, and detects Carriage head ass’y operation errors.
The home position sensor consists of an LED and photo transistor. When the Carriage head ass’y moves,
the detection plate passes between the LED and photo transistor and blocks the optical axis of the photo
transistor, changing the output level of the photo transistor.
Head carriage detection plate
+5V
LED
Photo transistor
Detection signal
GND
Rev. 2.00
- 132 -
SRP-275
8-3-2 Paper near end detection mechanism
Paper near end detection mechanism consists of Switch-paper near end and Switch-paper near end-W
(using the wall mount). These switches detect the amount of paper left on the paper roll through OR logical
operation.
The Switch-paper near end consists of the paper near end detection lever and micro switch, and is located
on the left of the Cover base. The Switch-paper near end-W consists of the near end detection lever and
micro switch, and is located on the left of the Cover middle. These switches detect the amount of paper left
on the paper roll.
The tip of the paper near end detection lever is always pressed against the paper roll by a spring inside the
micro switch. Therefore, when there is a large amount of paper remaining on the roll, the paper near end
detection lever is pressed against the paper roll as figure.
This keeps the micro switch turned on. When the almost out of paper on the roll the tip of the paper near end
detection lever is no longer pressed against the paper roll and moves in the direction indicated by the arrow
A. This turns the micro switch off and generates a signal indicating that the paper roll is near its end.
Switch-cover rear open
Switch-paper near end-W
Switch-paper near end
Frame basket
Cover middle
Switch-paper end
Cover base
Switch-cover rear open
Switch-paper near end-W
Cover middle
C
Roll paper
A
B
Paper inside core
Frame basket
A
Cover base
Rev. 2.00
Switch-paper near end
- 133 -
SRP-275
8-3-3 Paper end detection mechanism
The Switch-paper end consists of the paper end detection lever and micro switch, and is located on the
center of the Frame basket. This switch detects the presence/absence state of the paper roll.
The tip of the paper end detection lever is always pressed against the paper roll by a spring inside the micro
switch. Therefore, when there is a paper remaining on the roll, the paper end detection lever is pressed
against the paper roll as figure.
This keeps the micro switch turned on. When the almost out of paper on the roll the tip of the paper end
detection lever no longer presses against the paper roll and moves in the direction indicated by the arrow B.
This turns the micro switch off and generates a signal indicating that the paper roll is end.
8-3-4 Rear cover open detection mechanism
The Switch-cover rear open detects the Cover rear open/close state, the Switch-cover rear open is
located on the right of Cover middle.
This keeps the micro switch turned on. When the almost out of Cover rear the tip of the rear cover detection
lever no longer presses against the Cover rear and moves in the direction indicated by the arrow C.
This turns the micro switch off and generates a signal indicating that the Cover rear is open.
8-3-5 Auto cutter home position detection mechanism
The Auto cutter home position detection mechanism is located at the right end of the circular cutter subset
stroke. This mechanism confirms the position of the circular cutter and detects any abnormalities in its
operation. Initial setting is performed by sensing the detection plate on the rear of the AC upper cutter ass’y.
The Auto cutter home position sensor consists of an LED and a photo IC. When the circular cutter moves,
the detection plate moves between the LED and the photo IC.
The beam of light is then interrupted, and the output level of the photo IC changes. This change in the output
level is read and used as the circular cutter position detection signal.
Auto cutter detection plate
+5V
LED
Photo transistor
Detection signal
Circular cutter
GND
Auto cutter home position sensor
Rev. 2.00
- 134 -
SRP-275
8-4 Auto cutter mechanism
When the Auto cutter motor set drives the worm gear so that it rotates in the direction of arrow A, the
rotational force is transferred to the Gear-AC worm wheel and Gear-AC gear pulley (Belt drive pulley).
Each gear rotates in the direction of arrow. In accordance with rotation of the Gear-AC gear pulley (Belt
drive pulley), belt moves in direction of arrow B. The AC upper cutter guide ass’y is connected on the belt
so that it moves in direction of arrow C. When the circular cutter moves on the lower cutter, the paper is cut.
Power-AC-timing belt
Gear-AC gear pulley
Motor-DC
Gear-AC worm wheel
Gear-AC worm
Home position sensor
A
B
C
Belt drive pulley
Belt pulley
Cutting position
Home position
Circular cutter
AC upper cutter guide ass’y
Shaft-AC-shaft guide
Rev. 2.00
- 135 -
SRP-275
8-5 Easy paper loading mechanism
SRP-275 has easy paper loading mechanism which enables a paper loading and a paper jam to be solved
easily. When a paper jam happens or a paper is out, push Button open then the force will be transferred to
Arm open. The protrusion portion of Arm open will push up the Frame-clamshell locking of Rotator ass’y.
After removing a paper jam or replacing a paper roll, close the Cover rear.
Arm open
Frame-clamshell locking
Rev. 2.00
Button open
- 136 -