Audiovox ca 1552 Installation guide

PROFESSIONAL
SERIES
2 Way Security and Keyless Entry
Installation Guide
ca 1552
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
1
Table of Contents
Before You Begin ...................................................................................... 3
Wire Connection Guide ........................................................................... 4
5 Pin Main Harness ................................................................................... 5
9 Pin Input / Output Harness .................................................................... 6
4 Pin AUX Output Harness ....................................................................... 8
3 Pin Door Lock Output Harness ........................................................... 10
Additional Ports ...................................................................................... 14
Antenna / LED / Programming Port ....................................................... 14
DBI Port .................................................................................................... 14
Set Up & Programming .......................................................................... 15
Transmitter Programming ........................................................................ 15
Manual Feature Programming ................................................................. 15
Programming Feature Banks .................................................................. 16
Adjusting the Shock Sensor .................................................................. 16
Testing the Shock Sensor ...................................................................... 16
Chirp Delete - User Accessible .............................................................. 18
Dome Light Delay / Theater Dimming ..................................................... 18
Feature Descriptions ............................................................................. 18
Transmitter Button Functions ............................................................. 23
Security Trigger Zones ......................................................................... 24
System Layout ......................................................................................... 25
2
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
BEFORE YOU BEGIN
PROFESSIONAL INSTALLATION
STRONGLY RECOMMENDED
Installation Precautions:
Roll down window to avoid locking keys in vehicle
during installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Use grommets when routing wires through metal
surfaces
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE A TEST LIGHT, OR
"COMPUTER SAFE PROBE" as these can set off air
bags or damage vehicle computers.
Technical Support (800) 421-3209
or go to
http://techservices.codesystems.com
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
3
5 Pin Main Harness
9 Pin Input / Output Harness
4 PIN AUX
OUTPUT
4 Pin AUX Output Harness
1
PINK/BLACK
AUX 5 OUTPUT ( - )
2
ORANGE/BLACK
AUX 4 OUTPUT ( - )
3
GRAY/BLACK
AUX 3 OUTPUT ( - )
4
WHITE/BLACK
AUX 2 OUTPUT ( - )
3 Pin Lock Output Harness
4
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
5 Pin Main Harness
1
WHITE/RED
PARKING LIGHT INPUT
2
WHITE
PARKING LIGHT OUTPUT
Locate the parking light output wire at the vehicle’s light switch.
Verification: This wire registers positive voltage when the parking lights are
turned on.
Positive switching Parking Lights:
Connect the WHITE/RED wire to a 15 Amp max fused battery source.
Connect the WHITE wire to the parking light output wire.
Negative switching Parking Lights:
Connect the WHITE/RED wire to a good chassis ground.
Connect the WHITE wire to the parking light output wire.
3
BLACK
GROUND
Connect the BLACK wire to a solid chassis ground point using a ring terminal and
self tapping screw (not supplied). Scrape away paint from the grounding point to
ensure a good connection. The recommended grounding point is a metal surface
in the driver’s side kick panel area.
NOTE: Do not ground the BLACK wire with any other vehicle components.
4
BROWN
SIREN OUTPUT ( + )
Locate a suitable mounting location in the engine compartment for the siren, away
from moving parts.
With the bell of the siren aiming downwards, secure the siren in place using self
tapping screws, being careful not do drill into any hoses, wiring or components.
Connect the BLACK siren wire to a chassis ground using a ring terminal and self
tapping screw (not supplied).
Route the BROWN siren output wire from the control module through the firewall
and connect to the RED wire on the siren.
NOTE: Be sure to loom the siren wires, and seal the grommet.
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
5
5
RED
BATTERY 12V ( + )
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register ( + ) voltage in all positions of the ignition
switch.
Connect the RED wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
9 Pin Input / Output Harness
1
BLUE/WHITE
INSTANT TRIGGER INPUT ( - )
This wire is a GROUND input for an external sensor or secondary pin switch.
Verification: This wire when connected will trigger the security system.
2
GREEN
DOOR TRIGGER INPUT ( - )
Locate the vehicle’s dome light or door pin switch wire.
Verification: This wire will register ground (NEG) when the door is opened
and the interior light is on. This wire will register positive voltage when the
door is closed and the interior light is off.
Connect the GREEN wire to the vehicle’s negative door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle
application guide
3
ORANGE
GROUND WHEN ARMED OUTPUT ( - )
This wire will have a continuous ( - ) 200mA output when the system is Armed. This
wire is typically used for controlling window modules or additional sensors.
This output is configurable in option programming.
6
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
4
PURPLE
DOOR TRIGGER INPUT ( + )
Locate the vehicle’s dome light or door pin switch wire.
Verification: This wire will register positive voltage (POS) when the door is
opened and the interior light is on. This wire will
register ground or "0" Volts when the door is closed and the interior light is
off.
Connect the PURPLE wire to the vehicle’s positive door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle
application guide
5
YELLOW
IGNITION INPUT ( + )
Locate the vehicle’s ignition wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to the ON (or
RUN) position. The voltage does not drop out when the key is turned to the
START (or CRANK) position.
Connect the YELLOW wire to the vehicle’s Ignition wire.
6
RED/WHITE
TRUNK RELEASE OUTPUT ( - )
Locate the vehicle’s trunk release wire at the trunk release switch.
Verification: This wire will register either positive voltage or ground when
the trunk release is activated.
This is a low current output, 200mA.
7
BROWN/BLACK
HORN OUTPUT ( - )
Locate the vehicle’s horn wire.
Verification: This wire will register at positive voltage and register
ground when the horn switch is pressed.
Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low current
output, 200mA.
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
7
8
VIOLET/BLACK
AUX 1
This wire provides a ( - ) 200mA output capable of driving relays. For Control of
optional accessories (i.e. Power Window/Sunroof, etc.).
To activate refer to the transmitter button configuration chart. Please refer to the
selectable options for timing.
9
LT GREEN/BLACK
FACTORY DISARM OUTPUT ( - )
This wire will supply a ( - ) 200mA pulse upon disarming the system. Locate the
factory perimeter alarm disarm wire from the key cylinder inside the drivers door.
Verification: This wire registers ground if the key is turned to the unlock
position in the driver’s door cylinder.
Connect the LT GREEN/BLACK wire to the factory alarm disarm wire.
4 Pin AUX Output Harness
1
PINK/BLACK
AUX 5
This wire provides a ( - ) 200mA output capable of driving relays. For Control of
optional accessories (i.e. Power Window/Sunroof, etc.).
To activate refer to the transmitter button configuration chart. Please refer to the
selectable options for timing.
2
ORANGE/BLACK
AUX 4
This wire provides a ( - ) 200mA output capable of driving relays. For Control of
optional accessories (i.e. Power Window/Sunroof, etc.).
To activate refer to the transmitter button configuration chart. Please refer to the
selectable options for timing.
8
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
3
GRAY/BLACK
AUX 3
This wire provides a ( - ) 200mA output capable of driving relays. For Control of
optional accessories (i.e. Power Window/Sunroof, etc.).
To activate refer to the transmitter button configuration chart. Please refer to the
selectable options for timing.
4
WHITE/BLACK
AUX 2
This wire provides a ( - ) 200mA output capable of driving relays. For Control of
optional accessories (i.e. Power Window/Sunroof, etc.).
To activate refer to the transmitter button configuration chart. Please refer to the
selectable options for timing.
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
9
3 Pin Lock Output Harness
1
BLUE
UNLOCK ( - )
3
GREEN
LOCK ( - )
The door lock / unlock outputs are designed to control several different types of
systems which may require additional parts. Please review the wire and location
chart to see which type of door lock system is in your vehicle. The most common
types are shown in the following diagrams.
Negative Switching Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /
unlock switch.
Verification: These wires will register ground when the Lock and Unlock
switches are activated.
Connect the GREEN and BLUE wires shown in the diagram below.
Negative Locks:
GREEN (-) Lock Output
Lock
Vehicle Door Lock
Control Relays
Unlock
BLUE (-) Unlock Output
10
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
Positive Switching Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /
unlock switch.
Verification: These wires will register positive voltage when the Lock and
Unlock switches are activated.
Connect the GREEN and BLUE wires shown in the diagram below.
Positive Locks:
Fused +12 Volt
Battery Souce
87
87a
86
85
GREEN (-) Lock Output
30
Lock
Fused +12 Volt
Battery Souce
Vehicle Door Lock
Control Relays
87
Unlock
87a
86
85
BLUE (-) Unlock Output
30
Reverse Polarity Locks (5-Wire Door locks)
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /
unlock switch.
Verification: These wires will rest at ground and register positive
voltage when the Lock and Unlock switches are activated.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram
below using (2) SPDT relays (not supplied).
Reverse Polarity Locks:
Fused +12 Volt
Battery Souce
87
87a
86
85
GREEN (-) Lock Output
30
Lock
X
To Door Lock Motor
Cut
Unlock
Fused +12 Volt
Battery Souce
87
87a
86
85
BLUE (-) Unlock Output
30
X
To Door Lock Motor
Cut
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
11
Negative Multiplexed Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /
unlock switch.
Verification: This wire will show variable ground when the switch is activated.
Please consult the wire and location chart for specific resistor values for
your vehicle.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram
below using (2) SPDT relays (not supplied).
Multiplex Locks:
Ground
87
87
87a
GREEN (-) Lock Output
86
85
87a
Fused +12 Volt
Battery Source
86
85
BLUE (-) Unlock Output
30
30
Resistor
Lock
Vehicle Door Lock
Control Relays
Unlock
Positive Multiplexed Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock /
unlock switch.
Verification: This wire will show variable positive voltage when the switch is
activated. Please consult the wire and location chart for specific resistor
values for your vehicle.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram
below using (2) SPDT relays (not supplied).
Multiplex Locks:
87
87
87a
GREEN (-) Lock Output
86
85
Fused +12 Volt
Battery Source
Lock
87a
86
85
BLUE (-) Unlock Output
30
30
Resistor
Vehicle Door Lock
Control Relays
Unlock
12
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
Adding Aftermarket Actuators
After installing aftermarket actuators, (not supplied). Connect the GREEN and
BLUE wires shown in the diagram below using (2) SPDT relays (not supplied).
Fused +12 Volt
Battery Source
87
Door Lock
Actuator
87a
GREEN (-) Lock Output
85
86
30
Chassis
Ground
M
Fused +12 Volt
Battery Source
87
87a
BLUE (-) Unlock Output
85
86
30
Chassis
Ground
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
13
Additional Ports
Antenna / LED / Programming Port
Mount the supplied antenna/receiver to a clear spot on the vehicle's windshield
that will not block the driver's vision. A good location is usually high on the
windshield near the rear view mirror. Be careful not to mount the antenna/receiver
on any metallic window film, as this will effect system range. Route the antenna/
receiver cable to the control module and plug into the antenna port.
Data Bus Interface Port
This 4 pin port is used for Flashlogic Door Lock and Transponder Databus
Interfaces to communicate with the vehicle's Databus. When using the DBI port to
control the Flashlogic Door Lock and Transponder Interface modules the
following options may be available. Please refer to the D2D (Data to Data)
function list available per vehicle on the tech service web site.
Door Trigger
Trunk/Hatch Open
Door Lock Control
Dome Light Supervision
Factory Alarm Arm / Disarm
Manual Arm / Disarm Inputs (factory keyless controls system)
14
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
Set Up & Programming
Transmitter Programming - Feature Bank 1
1.
Turn the ignition ON.
2.
Press and hold the valet/override button.
3.
Within 10 seconds the system will chirp (3) three times.
4.
Press 1 button of each transmitter you wish to program.
5.
The system will respond with 1 chirp for each accepted transmitter.
6.
Pressing the override button at anytime during programming will advance to
the next bank.
NOTE: The system will exit transmitter programming after 15 seconds of inactivity.
NOTE: This system has 1 button programming which programs all channels of the
system.
NOTE: The system will hold up to 4 transmitters in memory, programming a 5th
transmitter will erase the oldest transmitter in memory.
NOTE: This system has PTN - Programmed Transmitter Notification. Each time the
ignition is turned ON, the LED will flash the number of transmitters programmed to
the system.
Transmitter programming for 2 Car Mode *2 way transmitter only:
1.
Enter the transmitter into 2 Car Mode. (Refer to transmitter operation in
the owners manual for 2 car operation)
2.
Follow the steps above for transmitter programming.
NOTE: 2 car mode requires an additional security system installed in a second
vehicle.
Manual Feature Programming - Feature Bank 2 & 3
1.
Turn the ignition ON.
2.
Press and hold the valet/override button.
3.
Within 10 seconds the system will chirp (3) three times.
4.
Use the valet/override button to advance through each option bank. For
feature programming advance to Feature Bank 2 or 3, which is (4) four and
(5) five chirps.
5.
Use the transmitter
button to scroll through the selections in each
feature bank, the system will chirp to match the feature number.
6.
Press the transmitter button to change the desired feature. The LED will
flash indicating the changed feature.
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
15
Defaulting All Features: Pressing the
button anytime while in any of the
feature banks will default all features and return you to feature bank 2 - 4 chirps.
NOTE: The system will remain in feature programming mode as long as the
ignition is on, there is no time limit. To exit programming turn the IGNITION OFF.
Feature Bank 1 - 3 Chirps
Transmitter Programming
Refer to transmitter programming.
16
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
Feature Bank 3 - 5 Chirps
Output Control
1 LED Flash
2 LED Flash
3 LED Flash
1
Extended Lock Pulse
1 Second
3.5 Seconds
1 Second Lock , 30 Second
Double Pulse
Lock, Double
Unlock
Pulse Unlock
2
Factory Disarm
Factroy
Disarm
2nd Unlock
3
Ignition Controlled Locks
OFF
Lock and
Unlock
Lock Only
Unlock Only
4
Trunk Output Timing
Red / White Output
Press and
Hold
10 Seconds
20 Seconds
Latched until
IGN ON
Latched ON
until Button
Press
5
Horn Output Timing
16mS
10mS
30mS
40mS
50mS
6
Real Panic
ON
OFF
7
AUX 1
Violet / Black Output
Push and Hold Latched
Latched until
IGN ON
Dome Light
Output
8
AUX 2
White / Black Output
Push and Hold Latched
Latched until
IGN ON
10 Second
10 Second
Pulse with
Pulse with Arm
Disarm
9
AUX 3
Gray / Black Output
Push and Hold Latched
Latched until
IGN ON
10 Second
10 Second
Pulse with
Pulse with Arm
Disarm
10
AUX 4
Orange / Black Output
Push and Hold Latched
Latched until
IGN ON
10 Second
10 Second
Pulse with
Pulse with Arm
Disarm
11
AUX 5
Pink / Black Output
Push and Hold Latched
Latched until
IGN ON
10 Second
10 Second
Pulse with
Pulse with Arm
Disarm
4 LED Flash
5 LED Flash
Double Pulse
Lock, 1 Second
Unlock
Adjusting the Shock Sensor
1.
Increase sensitivity by turning the adjustment dial clockwise.
2.
Decrease sensitivity by turning the adjustment dial counter clockwise.
Testing the Shock Sensor
Arm the system and wait 6 seconds for the zone to stabilize, then firmly strike
the vehicles bumper.
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
17
Chirp Delete - User Accessible
System ARM/DISARM chirps can be toggled ON or OFF without entering the
programming feature banks.
1.
Turn the ignition ON then OFF.
2.
Press and release the valet/programming button 3 times. The system
will respond with 1 chirp for ON or 2 chirps for OFF.
Dome Light Delay / Theater Dimming
The system can be programed to delay arming after the lock button is pressed (60
second max) for vehicles with a dome light delay or theater dimming feature. Once
programed the system will ‘learn’ the timing of the dome light delay and add 2
seconds before arming.
1.
Close all doors with ignition off.
2.
Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK ,
UNLOCK, LOCK. The LED will light solid to indicate the system has
entered DOME DELAY LEARN MODE.
3.
Immediately OPEN then CLOSE the door WITHOUT disarming the
system. The system will then monitor the door trigger wire. Once the
dome light turns off, the system will then add 2 seconds and then exit
the learning mode.
4.
The LED will begin to flash indicating the system has exited the
learning mode and is now armed.
Feature Descriptions
Feature Bank 2 - Security
1 - Silent Choice: Controls the normal arm/disarm chirps of the security system.
ON - Silent arming/disarming upon first press of lock/unlock, pressing lock/
unlock a second time will activate the arm/disarm chirps respectively. The
system will only sound the arm/disarm chirps upon a second press of the
lock/unlock buttons.
OFF - normal arm/disarm chirps upon the first press of lock/unlock.
18
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
2 - Passive Locks: Determines manual or automatic locking of the vehicle’s
doors.
Active - Requires use of the transmitter to lock the vehicle’s doors.
Passive - Automatically locks the vehicle’s doors 1 minute after the last door
is closed
3 - Passive Arming: Determines manual or automatic locking of the vehicle’s
doors.
Active - Requires use of the transmitter to arm the security system.
Passive - Automatically arms the security system 1 minute after the last door
is closed
4 - Siren / Horn: This feature selects which output(s) will sound the system’s
arm/disarm chirps. This feature does not effect the triggered state of the security
system and during a triggered cycle, both the siren and horn outputs will activate
respectively.
5 - Siren Duration: Determines the length of time the system will sound the
siren/horn during a full trigger event.
6 - Security: Controls security functionality - ON / OFF.
ON - Full security functionality.
OFF - The security system does not trigger. Panic and all other convenience
features operate as normal.
7- Anti-Hijack Mode: Controls car jack mode - ON / OFF.
OFF - Standard security system operation.
ON - Enables Car Jack mode functionality as described in the owners
manual
8 - Ground While Armed / Orange Output: Controls the output of the orange
wire. This wire will either supply a ( - ) output when armed OR disarmed.
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
19
Feature Bank 3 - Output Control
1 - Extended Lock Pulse: Controls the timing of the BLUE and GREEN lock
output wires.
1 Second - Single 1 second lock pulse, single 1 second unlock pulse.
3.5 Seconds - Single 3.5 second lock pulse, single 3.5 second unlock pulse.
1 Second Lock, Double Pulse Unlock - Single 1 second lock pulse, double 1
second unlock pulse.
30 Second Lock, Double Pulse Unlock - Single 30 second lock pulse, double
1 second unlock pulse.
Double Pulse Lock, 1 Second Unlock - Double 1 second lock pulse, single 1
second unlock pulse.
2 - Factory Disarm: Controls the timing of the LT. GREEN/BLACK factory disarm
output.
Factory Disarm - Single 1 second pulse with unlock.
2nd Unlock - Same output as unlock with 2nd press of unlock.
3 - Ignition Controlled Locks: Control of door locks when the ignition is cycled
ON or OFF.
OFF - Door locks not activated by ignition.
Lock and Unlock - Doors lock when ignition is turned on and unlock when
ignition is turned off.
Lock Only - Doors lock when ignition is turned on.
Unlock Only - Doors unlock when ignition is turned off.
4 - Trunk Output Timing - Red/White Output: Control of the RED/WHITE trunk
release output wire when trunk release is activated from the transmitter.
Push and Hold - Output is continuously active until transmitter button is
released.
10 Seconds - Output stays active for 10 seconds regardless of length
button press on transmitter.
20 Seconds - Output stays active for 20 seconds regardless of length
button press on transmitter.
Latched until IGN ON - Output stays active until the ignition is turned on.
Latched ON until Button Press - Output stays active until deactivated by
transmitter.
20
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
5 - Horn Output Timing: Control the minimum horn pulse time in milli seconds,
some vehicle will require a longer pulse to activate the factory horn.
16mS
10mS
30mS
40mS
50mS
6 - Real Panic: Controls the panic out when triggered from the transmitter.
ON - Randomized horn honks when panic is triggered.
OFF - Standard pattern horn honks when panic is triggered.
7 - AUX 1: Controls the VIOLET/BLACK AUX 1 output activation type and timing.
Push and Hold - Output is continuously active until transmitter button is
released.
Latched - Output stays active until button is pressed again.
Latched until IGN ON - Output stays active until the ignition is turned on.
Dome Light Output - Output is used for illuminated entry and is not controlled
by the AUX 1 function of the transmitter.
8 - AUX 2: Controls the WHITE/BLACK AUX 2 output activation type and timing.
Push and Hold - Output is continuously active until transmitter button is
released.
Latched - Output stays active until button is pressed again.
Latched until IGN ON - Output stays active until the ignition is turned on.
10 Second Pulse with Arm - Output stays active for 10 seconds with press
of lock button.
10 Second Pulse with Disarm - Output stays active for 10 seconds with
press of unlock button.
9 - AUX 3: Controls the GRAY/BLACK AUX 3 output activation type and timing.
Push and Hold - Output is continuously active until transmitter button is
released.
Latched - Output stays active until button is pressed again.
Latched until IGN ON - Output stays active until the ignition is turned on.
10 Second Pulse with Arm - Output stays active for 10 seconds with press
of lock button.
10 Second Pulse with Disarm - Output stays active for 10 seconds with
press of unlock button.
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
21
10 - AUX 4: Controls the ORANGE/BLACK AUX 4 output activation type and
timing.
Push and Hold - Output is continuously active until transmitter button is
released.
Latched - Output stays active until button is pressed again.
Latched until IGN ON - Output stays active until the ignition is turned on.
10 Second Pulse with Arm - Output stays active for 10 seconds with press
of lock button.
10 Second Pulse with Disarm - Output stays active for 10 seconds with
press of unlock button.
11 - AUX 5: Controls the PINK/BLACK AUX 5 output activation type and timing.
Push and Hold - Output is continuously active until transmitter button is
released.
Latched - Output stays active until button is pressed again.
Latched until IGN ON - Output stays active until the ignition is turned on.
10 Second Pulse with Arm - Output stays active for 10 seconds with press
of lock button.
10 Second Pulse with Disarm - Output stays active for 10 seconds with
press of unlock button.
22
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
Transmitter Button Functions
1 Way
Transmitter
Lock
Lock
Unlock
Car Find /
Panic
Trunk
X
Operation Method
Press and Release
Unlock
X
Press and Release
2 Step Unlock
X
Press and Release 2 times
Trunk
X
Push and Hold (3 Sec)
Car Finder
X
Press and Release
Panic
X
Push and Hold (3 Sec)
AUX 1
X
X
Push and Hold (3 Sec)
Shock Bypass
X
X
Press and Release Lock then
Press Lock + Car Find
Hidden Alarm
X
X
Press and Release Car Fnd then
Press Lock
X
Press and Release
Passive Arming
Bypass
X
AUX 2, 3, 4, 5 - Access in AUX Mode
Enter AUX Mode
AUX 2
AUX 3
AUX 4
X
X
X
Press and Hold Find + Trunk
Transmitter LED flashes 1 time
Push and Hold (3 Sec)
X
Push and Hold (3 Sec)
X
AUX 5
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
Push and Hold (3 Sec)
X
Push and Hold (3 Sec)
23
2 Way
Transmitter
Lock
Lock
Unlock
Car Find /
Panic
Trunk
Function Operation Method
X
Press and Release
Unlock
X
Press and Release
2 Step Unlock
X
Press and Release 2 times
Trunk
X
Push and Hold (3 Sec)
Car Finder
X
Press and Release
Panic
X
Push and Hold (3 Sec)
AUX 1
X
X
Shock Bypass
X
X
Press and Release Lock then
Press Lock + Car Find
Hidden Alarm
X
X
Press and Release Car Fnd then
Press Lock
X
Press and Release
Passive Arming
Bypass
X
Push and Hold (3 Sec)
Menu
X
Press and Release
AUX 2, 3, 4, 5 - Access in AUX Mode
Enter AUX Mode
AUX 2
X
X
Press and Hold F for 2 seconds
LCD displays AU
Push and Hold (3 Sec)
AUX 3
X
AUX 4
Push and Hold (3 Sec)
X
Push and Hold (3 Sec)
AUX 5
X
Push and Hold (3 Sec)
Security Trigger Zones
If the security system has been triggered the LED will flash one of the patterns
below indicating the zone.
LED FLASHES TRIGGER ZONE
24
2 Flashes
Hood / Trunk Input
3 Flashes
Door Input
4 Flashes
Shock Sensor
5 Flashes
Ignition Input
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
CA 1552
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.
25
AUX 5 OUTPUT ( - )
AUX 4 OUTPUT ( - )
AUX 3 OUTPUT ( - )
AUX 2 OUTPUT ( - )
PINK/BLACK
ORANGE/BLACK
GRAY/BLACK
WHITE/BLACK
DBI PORT
BLUE
OPEN
GREEN
ANTENNA
LED
VALET
LOCK OUTPUT ( - )
UNLOCK OUTPUT ( - )
PARKING LIGHT INPUT
PARKING LIGHT OUTPUT
GROUND
SIREN OUTPUT ( + )
BATTERY 12V ( + )
WHITE/RED
WHITE
BLACK
BROWN
RED
SHOCK SENSOR PORT
INSTANT TRIGGER INPUT ( - )
DOOR TRIGGER INPUT ( - )
GROUND WHEN ARMED ( - )
DOOR TRIGGER INPUT ( + )
IGNITION INPUT ( + )
TRUNK RELEASE OUTPUT ( - )
HORN OUTPUT ( - )
AUX 1 ( - )
FACTORY DISARM OUTPUT ( - )
BLUE/WHITE
GREEN
ORANGE
PURPLE
YELLOW
RED/WHITE
BROWN/BLACK
VIOLET/BLACK
LT GREEN/BLACK
Audiovox Electronics Corporation.
Customer Service 1-800-421-3209
WWW.CODE-ALARM.COM
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference
that may cause undesired operation.
Warning!
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
26
ca1552. 2011 Audiovox Electronics Corporation. All rights reserved.