Refrigerator
user manual
This manual is made with 100% recycled paper.
English
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
Free Standing Appliance
DA99-01950A(1.0)-EN.indd 1
2011.11.23 5:8:40 PM
safety information
SAFETY INFORMATION
• Before operating the appliance, please read
this manual thoroughly and retain it for your
reference.
• Use this appliance only for its intended purpose
as described in this instruction manual.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety.
These warning signs are here to prevent
injury to you and others.
Please follow them carefully.
After reading this section, keep it in a safe
place for future reference.
CE Notice
This product has been determined to be in
compliance with the Low Voltage Directive
(2006/95/EC), the Electromagnetic Compatibility
Directive (2004/108/EC) and the Eco-Design
Directive(2009/125/EC) implemented by
Regulation (EC) No 643/2009 of the European
Union.
• Because these following operating instructions
cover various models, the characteristics of
your refrigerator may differ slightly from those
described in this manual.
WARNING
Important safety symbols and
precautions :
WARNING
CAUTION
Hazards or unsafe practices that
may result in severe personal
injury or death.
Hazards or unsafe practices that
may result in minor personal
injury or property damage.
Do NOT attempt.
Do NOT disassemble.
Do NOT touch.
Follow directions carefully.
Unplug the power plug from the
wall socket.
Make sure the machine is grounded
to prevent electric shock.
Call the contact center for help.
SEVERE WARNING SIGNS
FOR INSTALLATION
• Do not install the refrigerator in a damp
place or place where it may come in
contact with water.
- Deteriorated insulation of electrical parts may
cause an electric shock or fire.
• Do not place this refrigerator in direct sunlight or
expose to the heat from stoves, room heaters or
other appliance.
• Never use gas pipes, telephone lines or other
potential lightening rods as ground.
- Improper use of the ground plug can result in
electric shock.
• Do not plug several appliances into the same
multiple power board.
The refrigerator should always be plugged into
its own individual electrical which has a voltage
rating that matched the rating plate.
- This provides the best performance and also
prevents overloading house wiring circuits, which
could cause a fire hazard from overheated wires.
• If the wall socket is loose, do not insert the
power plug.
- There is a risk of electric shock of fire.
• Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
• Do not bend the power cord excessively or
place heavy articles on it.
Note.
2_ safety information
DA99-01950A(1.0)-EN.indd Sec2:2
2011.11.23 5:8:42 PM
• This refrigerator must be properly installed
and located in accordance with the manual
before it is used.
• Connect the power plug in proper position with
the cord hanging down.
- If you connect the power plug upside down, wire
can get cut off and cause fire or electric shock.
• When moving the refrigerator, be careful not to
roll over or damage the power cord.
- This constitutes a fire hazard.
• Make sure that the power plug is not squashed
or damaged by the back of the refrigerator.
• Keep the packing materials out of reach of
children.
- There is a risk of death from suffocation if
children put them on their head.
• The appliance must be positioned so that the
plug is accessible after installation.
• The refrigerator must be grounded.
- You must ground the refrigerator to prevent
any power leakages or electric shocks caused by
current leakage from the refrigerator.
• If the power cord is damaged, have it
replaced immediately by the manufacturer
or its service agent.
• The fuse on refrigerator must be changed by a
qualified technician or service company.
- Failing to do so may result in electric shock or
personal injury.
CAUTION
CAUTION SIGNS FOR
INSTALLATION
• Keep ventilation opening in the appliance
enclosure or mounting structure clear of
obstruction.
• Allow the appliance to stand for 2 hours after
installation.
WARNING
SEVERE WARNING SIGNS
FOR USING
• Do not put a container filled with water on the
refrigerator.
- If spilled, there is a risk of fire or electric shock.
• Do not let children hang on the door.
If not, a serious injury may occur.
• Do not let children enter inside of the refrigerator.
There is a risk of children entrapment.
• Never put fingers or other objects into the
dispenser hole.
- It may cause personal injury or material damage.
• Do not store volatile or flammable substances in
the refrigerator.
- The storage of benzene, thinner, alcohol, ether,
LP gas and other such products may cause
explosions.
• Do not store pharmaceuticals products, scientific
materials or temperature sensitive products in
the refrigerator.
- Products that require strict temperature controls
must not be stored in the refrigerator.
• Do not place or use electrical appliance inside
the refrigerator, unless they are of a type
recommended by the manufacturer.
• Do not use mechanical devices or any other
means to accelerate the defrosting process,
other than those recommended by the
manufacturer.
• Do not damage the refrigerant circuit.
• Do not disassemble or repair the
refrigerator by yourself.
- You run risk of causing a fire, malfunction and/or
personal injury.
• Children should be supervised to ensure
that they do not play with the appliance.
• Bottles should be stored tightly together so that
they do not fall out.
• This product is intended only for the storage of
food in a domestic environment.
• If a gas leak is detected, avoid any naked flames
or potential sources of ignition and air the room
in which the appliance is standing for several
minutes.
• Use only the LED Lamps provided by
manufacturer or service agents.
• Do not insert the power plug with wet
hands.
• Do not store articles on the top of the appliance.
- When you open or close the door, the articles
may fall and cause personal injury and/or
material damage.
safety information _3
DA99-01950A(1.0)-EN.indd Sec2:3
2011.11.23 5:8:42 PM
• If you smell pharmaceutical or smoke, pull
out power plug immediately and contact
your Samsung Electronics service center.
• If you experience difficulty when changing the
light, contact service agents.
• If the products equipped with LED Lamp,
do not disassemble Lamp Cover and LED Lamp
by yourself.
- Please contact your service agents.
CAUTION
CAUTION SIGNS FOR
USING
• To get Best performance of product,
- Do not place foods too closely in front of
the vents at the rear of the appliance as it can
obstruct free air circulation in the refrigerator
compartment.
- Wrap the food up properly or place it in airtight
containers before put it into the refrigerator.
• Fill water tank, ice tray, water cubes only with
potable water.
• If the refrigerator is damaged by water,
pull out the power plug and contact your
Samsung Electronics service center.
CAUTION
CAUTION SIGNS FOR
CLEANING
• Do not directly spray water inside or
outside the refrigerator.
- There is a risk of fire or electric shock.
• Do not spray inflammable gas near the
refrigerator.
- There is a risk of explosion or fire.
• Do not spray cleaning products directly on the
display.
- Printed letters on the display may come off.
• Remove any foreign matter or dust from
the power plug pins.
But do not use a wet or damp cloth when
cleaning the plug, remove any foreign
material or dust from the power plug pins.
- Otherwise there is a risk of fire or electric shock.
• Unplug the refrigerator before cleaning and
making repairs.
WARNING
SEVERE WARNING SIGNS
FOR DISPOSAL
• When disposing of this or other
refrigerators, remove the door/door seals,
door latch so that small children or animals
cannot become trapped inside.
Children should be supervised to ensure
that they do not play with the appliance.
• Please dispose of the packaging material for this
product in an environmentally friendly manner.
• Leave the shelves in place so that children may
not easily climb inside.
Ensure that none of the pipes on the back of the
appliance are damaged prior to disposal.
• R600a or R134a is used as a refrigerant.
Check the compressor label on the rear of
the appliance or the rating label inside the
refrigerator to see which refrigerant is used for
your refrigerator.
When this product contains flammable gas
(Refrigerant R600a), contact your local authority
in regard to safe disposal of this product.
Cyclopentane is used as a insulation blowing
gas. The gases in insulation material require
special disposal procedure.
Please contact your local authorities in regard to
the environmentally safe disposal of this product.
Ensure that none of the pipes on the back of the
appliances are damaged prior to disposal.
The pipes shall be broke in the open space.
• If the appliance contains iso-butane refrigerant
(R600a), a natural gas with high environmental
compatibility that is, however, also combustible.
When transporting and installing the appliance,
care should be taken to ensure that no parts of
the refrigerating circuit are damaged.
• Refrigerant squirting out of the pipes could ignite
or cause an eye injury.
If a leak is detected, avoid any naked flames or
potential sources of ignition and air the room
in which the appliance is standing for several
minutes.
4_ safety information
DA99-01950A(1.0)-EN.indd Sec2:4
2011.11.23 5:8:42 PM
• In order to avoid the creation of a
flammable gas-air mixture if a leak in the
refrigerating circuit occurs, the size of the
room in which the appliance may be sited
depends on the amount of refrigerant used.
Never start up an appliance showing any
signs of damage. If in doubt, consult your
dealer.
The room must be 1m³ in size for every 8g
of R600a refrigerant inside the appliance.
The amount of refrigerant in your particular
appliance is shown on the identification
plate inside the appliance.
ADDITIONAL TIPS FOR
PROPER USAGE
• In the event of a power failure, call the local
office of your Electricity Company and ask how
long it is going to last.
- Most power failures that are corrected in an
hour or two will not affect your refrigerator
temperatures.
However, you should minimize the number of
door openings while the power is off.
• If the key is provided with refrigerator, the keys
should be kept out of the reach of children and
not in vicinity of the appliance.
• The appliance might not operate consistently
(possibility of temperature becoming too warm
in refrigerator) when sited for an extended
period of time below the cold end of the range
of temperatures for which the refrigerating
appliance is designed.
• Do not store food which spoils easily at low
temperature, such as bananas, melons.
• Your appliance is frost free, which means there
is no need to manually defrost your appliance,
as this will be carried out automatically.
Saving Energy Tips
- Install the appliance in a cool, dry room with
adequate ventilation.
Ensure that it is not exposed to direct sunlight
and never put it near a direct source of heat
(radiator, for example).
- Never block any vents or grilles on the
appliance.
- Allow warm food to cool down before placing it
in the appliance.
- Put frozen food in the refrigerator to thaw.
You can then use the low temperatures of the
frozen products to cool food in the refrigerator.
- Do not keep the door of the appliance open for
too long when putting food in or taking food out.
The shorter time for which the door is open, the
less ice will form in the freezer.
- Clean the rear of the refrigerator regularly.
Dust increases energy consumption.
- Do not set temperature colder than necessary.
- Ensure sufficient air exhaust at the refrigerator
base and at the back wall of the refrigerator.
Do not cover air vent openings.
- Allow clearance to the right, left, back and top
when installing.
This will help reduce power consumption and
keep your energy bills lower.
contents
SETING UP YOUR SIDE-BY-SIDE REFRIGERATOR ·····································6
OPERATING YOUR REFRIGERATOR ····························································10
TROUBLESHOOTING ·····················································································14
INSTALL YOUR REFRIGERATOR···································································15
safety information _5
DA99-01950A(1.0)-EN.indd Sec2:5
2011.11.23 5:8:42 PM
setting up your refrigerator
GETTING READY TO INSTALL
THE REFRIGERATOR
Congratulations on your purchase of this Samsung
Refrigerator.
We hope you enjoy the state-of-art features and
efficiencies that this new appliance offers.
• This refrigerator must be properly installed and
located in accordance with the manual before it is
used.
• Use this appliance only for its intended purpose as
described in this instruction manual.
• We strongly recommend that any servicing be
performed by a qualified individual.
• Please dispose of the packaging material for this
product in an environmentally friendly manner.
or
600mm
Pull the power plug out of the socket
before changing the interior light of the
WARNING
refrigerator.
- Otherwise, there is a risk of electric shock.
at least
50 mm
1,175mm
Selecting the best location for the
refrigerator
• A location without direct exposure to sunlight.
• A location with flat floor surface.
• A location with enough space for the refrigerator
door to open easily.
• Allow sufficient space to the right, left, back and top
for air circulation.
If the refrigerator does not have enough space, the
internal cooling system may not work properly.
• Please ensure that appliance can be moved freely
in the event of maintenance & service.
550mm
1,010mm
• Height of the product may be different
depending on the models.
• Allow clearance to the right, left, back and top
when installing.
This will help reduce power consumption and keep
your energy bills lower.
• Do not install the refrigerator in a place with the
temperature lower than 10°C.
Pull the unit straight out when installing,
servicing or cleaning behind the
refrigerator and push it straight back after
work is complete. Make sure your floor can support
fully loaded refrigerator.
CAUTION
6_ setting up
DA99-01950A(1.0)-EN.indd Sec4:6
2011.11.23 5:8:42 PM
REVERSING THE
REFRIGERATOR DOOR
3. Disconnect the wires and then remove 3 bolts.
Required Tools (Not provided)
Phillips Head
Driver (+)
Flat Head
Driver (-)
10mm Socket
Wrench
(for bolts)
8mm
Socket Wrench
(for bolts)
Spanner
(for hinge shaft)
4mm Hex
Wrench
(for bottom
hinge shaft)
1. Remove 2 screws on the top of the refrigerator.
Screw
2. Remove the plastic cover and make sure to
disconnect the wire connected to it.
After removing the plastic cover, check the parts
for reversing the door.
WARNING
Make sure your refrigerator is unplugged
before handling electrical wires.
01 SETTING UP
Before you reverse the refrigerator door,
make sure to unplug the refrigerator.
WARNING
If this operation is performed by After
sales service, it is not covered as the warranty
service.
4. Remove the door from the lower hinge by carefully
lifting the door straight up.
Refrigerator door is heavy, be careful
not to injure yourself when removing the
CAUTION
refrigerator door.
5. Separate the front leg cover after removing
2 screws.
Screw
6. Unscrew 3 bolts tightening the hinge and also
unscrew 3 bolts on the bottom left side by the front
leg where removed hinge will be attached.
CAUTION
Be careful not to damage the electrical
wires when removing the plastic cover.
10mm
10mm
setting up _7
DA99-01950A(1.0)-EN.indd Sec4:7
2011.11.23 5:8:42 PM
7. Separate the hinge shaft by using hex wrench first.
Unscrew the bolt to remove the hinge riser and
switch the side of the hinge shaft and the hinge
riser.
11. Remove the hinge and the grommet from the
refrigerator door.
Detach the right side hinge cover and pull the
wires out of the hinge cover.
Hinge shaft
Hinge cover
Grommet
Hinge riser
8mm Bolt
CAUTION
8. Attach the hinge on the bottom left side of the
refrigerator where bolts were previously removed
in step 6.
Screw the bolts that were removed on the bottom
right side of the refrigerator for the future usage.
Be careful not to damage the electrical
wires when removing the hinge cover.
12. Use wrench to separate the hinge shaft and then
flip the hinge and reattach the hinge shaft.
10mm
10mm
9. Remove the screws on the bottom left and right
side of the refrigerator door.
Switch the side of the door stopper from right to
the left. Hinge riser should be switched as well.
Hinge riser
13. Reassemble the hinge on the refrigerator door by
reversing the step 11.
Make sure to use left side hinge cover (which can
be found underneath the removed plastic cover
from step 2) and remove the grommet.
After reassembling the hinge, wire and the hinge
cover, switch the side from right to the left.
Hinge riser
Grommet
10. Remove the wire cover on top of the refrigerator
door to switch the side of the wires.
14. After switching the hinge, close it with the wire
cover on the top of refrigerator door.
“Cover Wire Door R”
can be found in the
packaging
8_ setting up
DA99-01950A(1.0)-EN.indd Sec4:8
2011.11.23 5:8:43 PM
15. Take off the handle cover and remove the screws,
make sure to detach the caps and the handle
from the left to right side of the door.
(Make sure to cover the left side with detached
caps.)
19. Tighten 2 screws back to its place.
01 SETTING UP
20. Detach the Fridge and the Freezer door gaskets
and then attach them after rotating them 180˚.
Handles may not have cover depending on the
models.
16. Switch the hinge cap and attach the front leg
cover.
Carefully put the refrigerator door back on.
Hinge cap
17. Tighten the 3 bolts and then connect the wires
back together.
• After reversing the doors, make sure
the Fridge and Freezer door gaskets are
WARNING
properly arranged. If not, there might
be a noise or dew formed which affects
perfomance of the refrigerator.
LEVELLING THE REFRIGERATOR
If the front of the appliance is slightly higher than the
rear, the door can be opened and closed more easily.
Turn the adjusting legs clockwise to raise and
counter-clockwise to lower the height.
Case 1) The appliance tilts down to the left.
• Turn the left adjusting leg in the direction of the
arrow until the appliance is level.
Case 2) The appliance tilts down to the right.
• Turn the right adjusting leg in the direction of the
arrow until the appliance is level.
WARNING
Make sure your refrigerator is unplugged
before handling electrical wires.
18. Connect the wire on the plastic cover and put the
cover back to its original position.
< Case1 >
< Case2 >
setting up _9
DA99-01950A(1.0)-EN.indd Sec4:9
2011.11.23 5:8:43 PM
operating your refrigerator
CHECKING THE CONTROL
PANEL
1
2
3
(Hold
Hold 3 sec
for Display)
Display
4
5
3
Power Cool function cannot be used together
with Vacation function.
Selecting Vacation function will automatically
deactivate the Power Cool function.
Each time you press the button, a short beep
will sound.
4
USING THE CONTROL PANEL
1
Child Lock
Press the Child Lock button for 3
seconds to activate the Child Lock
function.
Child lock indicator will light up and all
the buttons on the control panel will
be locked.
To deactivate the Child Lock function, press the Child
Lock button again for 3 seconds.
2
Power Cool
Press the Power Cool button to
activate the Power Cool function.
Power Cool indicator will light up and
the refrigerator will speed up the time
to needed to cool products in the
refrigerator.
Power Cool function will operate for 2 hours and 30
minutes to quickly cool the refrigerator.
To deactivate the Power Cool function, press the
Power Cool button again.
Alarm
1. Alarm
Press the Alarm button to activate the
Alarm function. Alarm indicator will
light up and the refrigerator will alert
you with alarm sound if the refrigerator
door is kept open for longer than 2 minutes.
To deactivate the Alarm function, press the Alarm
button again.
2. Display Off
As standard, the temperature display is switched
off, to switch between on and off mode, press alarm
button for 3 seconds.
Fridge
Press the Fridge button to set the
desired temperature from the range
between 1°C and 7°C. Default
set temperature is set on 3°C and
each time you press the Fridge
button, temperature will change in following order
and temperature indicator will display the desired
temperature.
When the temperature setting is done, temperature
indicator will display the current temperature of the
refrigerator.
If current temperature is higher than 9°C, temperature
indicator will be displayed as 9°C.
5
Vacation
Press the Vacation button to activate
the Vacation function.
Vacation indicator will light up and the
refrigerator will set the temperature
to 15°C to minimize the power
consumption while you are away (on vacation or
business trip etc).
Keep the refrigerator free from bacteria and odor.
• Vacation function will be automatically
deactivated If you select
Power Cool function or adjust temperature
while Vacation function is on.
• Make sure to remove foods before using
Vacation function.
10_ operating
DA99-01950A(1.0)-EN.indd 섹션1:10
2011.11.23 5:8:45 PM
USING THE MOISTURE
CONTROL BIG BOX
1
You can use the moisture control big box to control
the humidity for the products which needs to be
preserved its freshness.
• Some of the features such as water tank
and the beverage station can be different
and may not be available depending on the
model.
• To get more space, you can remove water
1 tank.
It does not affect thermal and mechanical
characteristics.
A declared storage volume of refrigerator
compartment is calculated with this part
removed.
02 OPERATING
Use the humidity control
lever on the top of the
drawer to adjust the
humidity.
Move the lever to the
right side to keep the
humidity low within the
drawer.
Move the lever to the left side to keep the humidity
high. More holes will allow higher humidity within the
drawer.
USING THE BEVERAGE STATION
To open the beverage station, push the top part of
the beverage station.
Anti-sweat heater switch
When the humidity of the
indoor is high,
sweat may form around
the beverage station.
Turn the Anti-sweat heater
switch on, to remove
the sweat and turn the
switch off when the sweat
disappears.
Anti-sweat
heater switch
USING THE FOLDABLE SHELF
You can tuck in the foldable shelf if you need to
accommodate taller containers or products on the
shelf underneath.
Beverage station may not be available
depending on the model.
1. Slightly lift up the shelf
and slide it inward.
2. You can simply pull the
tucked in shelf to use
the fully extended shelf.
operating _11
DA99-01950A(1.0)-EN.indd 섹션1:11
2011.11.23 5:8:49 PM
USING THE WATER DISPENSER
Filling the water
You can fill the water with the water tank sitting inside
of the refrigerator or you can remove the water tank
to fill the water.
Method 1
Fill the water through the hole on the
top of the water tank.
If you pour the water too fast, water
may overflow.
Method 2
1. Release the lock on the both side of the water tank
to remove the lid on the water tank.
REMOVING THE INTERIOR
PARTS
Moveable deli bin
Pull the deli bin out fully
then slightly lift it up to
remove it.
Shelves
Gently lift up the shelves
with both hands and pull it
toward you.
(Glass shelf/Foldable shelf)
2. Fill the water in the water tank.
Drawers
CAUTION
Do not put anything other than water in
the water tank.
Pull the drawers out fully
then slightly lift it up
to remove the drawers.
(Plastic drawer/Moisture
control big box)
Getting water from the dispenser
Door guards
Place a glass underneath the
water outlet and push it
gently against the water
dispenser lever with your glass.
Blue light will turn on when you
push the lever.
Firmly grab the door
guards with both hands
and lift it up gently to
remove the door guards.
• Make sure the glass is in line with the
dispenser to prevent the water from splashing
out.
• Water dispenser may not be available
depending on the model.
Water tank
Firmly grab the water tank
with both hands and lift it
up towards you gently to
remove the water tanks.
Water tank may not be available depending on
the model.
12_ operating
DA99-01950A(1.0)-EN.indd 섹션1:12
2011.11.23 5:8:50 PM
Beverage station
1. Remove the door bin
locate on the top of the
beverage station.
02 OPERATING
2. Press the bottom left
and right part of the
beverage station with both hands lift up to open.
Beverage station may not be available
depending on the model.
Deodorizer
Push the lever as arrow
indicates and pull the
cover.
To get the best energy efficiency of this
product, please leave all selves, drawers
and baskets on their original position like as
illustration in page (11).
CLEANING THE REFRIGERATOR
WARNING
CAUTION
Do not use Benzene, Thinner or Clorox™
for cleaning.
They may damage the surface of the
appliance and can create a risk of fire.
Do not spray the refrigerator with water
while it is plugged in, as it may cause an
electric shock.
Do not clean the refrigerator with
benzene, thinner or car detergent for risk
of fire.
REPLACING THE INTERIOR LIGHT
For LED lamp, please contact service engineer
to replace it.
operating _13
DA99-01950A(1.0)-EN.indd 섹션1:13
2011.11.23 5:8:52 PM
troubleshooting
PROBLEM
SOLUTION
• Check if the power plug is correctly connected.
The appliance is not
operating at all or the
temperature is too high.
• Is the temperature control on the front panel correctly set?
• Does sun shine on the appliance or are there any heat sources
nearby?
• Is the back of the appliance too close to the wall?
• Check if the appliance is installed on a stable and even floor.
• Is the back of the appliance too close to the wall?
There are unusual noises.
• Have any foreign objects fallen behind or under the appliance?
• Is the noise coming from the compressor in the appliance?
• A ticking sound may be heard inside the appliance; this is normal.
This sound occurs when the various accessories contract or expand.
The front corners and sides
of the appliance are warm
and condensation starts to
form.
You can hear a liquid
bubbling in the appliance.
• Heat-proof pipes are installed in the front corners of the appliance to
prevent condensation from forming.
When the surrounding temperature rises, this may not always be
effective. However, this is not abnormal.
• In very humid weather, condensation may form on the outer surface of
the appliance when the moisture in the air comes into contact with the
cool surface of the appliance.
• This is the refrigerant, which cools the inside of the appliance.
• Is there any spoiled food inside of the refrigerator?
There is a bad smell inside
the appliance.
There is a layer of frost on
the appliances walls.
Condensation forms on the
inside wall of the appliance
and around vegetables.
• Make sure that strong smelling food (for example, fish) is wrapped so
that it is airtight.
• Clean out your refrigerator periodically and throw away any spoiled or
suspect food.
• Are the air outlet vents blocked by food stored inside the refrigerator?
• Space the food out as much as possible to improve ventilation.
• Is the door fully closed?
• Food with a high water content is stored uncovered with a high
humidity level or the door has been left open for a
long time.
• Store the food with a cover or in sealed containers.
14_ troubleshooting
DA99-01950A(1.0)-EN.indd 섹션2:14
2011.11.23 5:8:52 PM
How to install the product
Installation Part
Make sure to turn off the power for both of the
products.
Installing the products together
Side by Side combination possible with Samsung Models starting
with R Z**,RR**.
Please ask the shop for detail such as Color and Design.
For Side by Side arrangement, please make sure followings.
- Recommend to place the Fridge on the Right for best performance
- For perfect finish, allow the following clearance and install SPACERS
in installation Kit provided. (Only available on some models)
- Make the height of the refigerator and the freezer same with refering the 9 page.
Install Direction
Fixer
1. Keep the distance between the refrigerator and the
freezer about 5~7mm.
2. Remove the front leg cover on both refrigerator and
the freezer by removing the screws.
3. Remove the screw from the each of the product and
attach them back after putting the bottom fixer.
Joining Strip
Bottom Fixer A
4. Insert the joining strip in between the refrigerator
and the freezer.
Freezer
Refrigerator
5. Insert two fixers firmly on the top of the products.
Bottom Fixer A
Front Leg Cover
Fixer
at least
50mm
Joining
Strip
1175
at least
50mm
6. Place the front leg cover back on both of the
products.
Install Direction
2030
7. Join the bottom fixer B with screws at back of the
products.
Required Tools
Fixer
Joining Strip
Bottom Fixer
A, B
Screws
Bottom Fixer B
install your refrigerator _15
DA99-01950A(1.0)-EN.indd 섹션2:15
2011.11.23 5:8:52 PM
Ambient Room Temperature Limits
This refrigerator is designed to operate in ambient temperatures specified by its temperature
class marked on the rating plate.
Class
Symbol
Ambient Temperature range (°C)
Extended Temperate
SN
+10 to +32
Temperate
N
+16 to +32
Subtropical
ST
+16 to +38
Tropical
T
+16 to +43
Internal temperatures may be affected by such factors as the location of the refrigerator,
ambient temperature and the frequency with which you open the door.
Adjust the temperature as required to compensate for these factors.
English
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection
systems)
This marking on the product, accessories or literature indicates that the product and its
electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with
other household waste at the end of their working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please separate these items
from other types of waste and recycle them responsibly to promote the sustainable reuse of
material resources.
Household users should contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can take these items for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other
commercial wastes for disposal.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
COUNTRY
CALL
Web site
AUSTRALIA
1300 362 603
www.samsung.com/au
COLOMBIA
01-8000112112
www.samsung.com.co
EIRE
0818 717 100
www.samsung.com/ie
(852) 3698-4698
www.samsung.com/hk
www.samsung.com/hk_en/
3030 8282, 1-800-3000-8282
1800-88-9999
www.samsung.com/in
www.samsung.com/my
0800 SAMSUNG (726-7864)
www.samsung.com/nz
800-7267
www.samsung.com/latin
PHILIPPINES
1800-10-SAMSUNG (726-7864)
www.samsung.com/ph
SINGAPORE
1800-SAMSUNG (726-7864)
www.samsung.com
SOUTH AFRICA
0860-SAMSUNG (726-7864)
www.samsung.com
U.K
0330 SAMSUNG (726-7864)
www.samsung.com
1 800 588 889
www.samsung.com
HONG KONG
INDIA
MALAYSIA
NEW ZEALAND
PANAMA
VIETNAM
Code No. DA99-01950A REV(1.0)
DA99-01950A(1.0)-EN.indd 섹션2:16
2011.11.23 5:8:57 PM