Quantum 610 Owner`s manual

Owner’s Manual
1-800-800-8586 (Exeter, PA) • 1-888-570-1113 (St. Catharines, ON) • www.quantumrehab.com
SAFETY
GUIDELINES
The symbols below are used throughout this owner's manual and on the power chair to identify warnings and important
information. It is very important for you to read them and understand them completely.
WARNING! Failure to follow designated procedures can cause either personal injury, component
damage, or malfunction (black symbol on yellow triangle with black border).
MANDATORY! These actions should be performed as specified. Failure to perform mandatory
actions can cause injury to personnel and/or damage to equipment (white symbol on blue dot).
PROHIBITED! These actions should be prohibited. These actions should not be performed at any
time or in any circumstances. Performing a prohibited action can cause injury to personnel and/
or damage to equipment (black symbol with red circle and red slash).
Copyright © 2006
Pride Mobility Products Corp.
INFMANU2924/RevB/January06
www.quantumrehab.com
Quantum 610
CONTENTS
I.
INTRODUCTION.................................................................................................................................... 4
II.
SAFETY .................................................................................................................................................... 6
III. YOUR POWER CHAIR ....................................................................................................................... 16
IV.
ASSEMBLY............................................................................................................................................ 21
V.
COMFORT ADJUSTMENTS........................................................................................................... 24
VI. BATTERIES AND CHARGING ....................................................................................................... 31
VII. OPERATION .......................................................................................................................................... 35
VIII. CARE AND MAINTENANCE ........................................................................................................... 50
IX. WARRANTY........................................................................................................................................... 56
This owner’s manual is compiled from the latest specifications and product information available at the time of publication.
We reserve the right to make changes as they become necessary. Any changes to our products may cause slight variations
between the illustrations and explanations in this manual and the product you have purchased.
Quantum 610
www.quantumrehab.com
3
I.
INTRODUCTION
SAFETY
WELCOME to Quantum Rehab, a division of Pride Mobility Products Corporation (Pride). The power chair you have
purchased combines state-of-the-art components with safety, comfort, and styling in mind. We are confident that these
design features will provide you with the conveniences you expect during your daily activities. Once you understand how
to safely operate and care for your power chair, it should give you years of trouble free operation and service.
Read and follow all instructions, warnings, and notes in this manual before attempting to operate your power chair for the
first time. In addition, your safety depends upon you, as well as your provider, caretaker, or healthcare professional in
using good judgement.
If there is any information in this manual which you do not understand, or if you require additional assistance for setup or
operation, please contact your Quantum Rehab Specialist. Failure to follow the instructions in this manual and those
located on your power chair can lead to personal injury and/or damage to the power chair, including voiding the
warranty.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter, or modify this product or remove or
render inoperable or unsafe any guards, shields, or other safety features of this product; fail, refuse, or neglect to install any
retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product.
INFORMATION EXCHANGE
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear about the safety
and reliability of your new power chair, and about the service you received from your Quantum Rehab Specialist.
Please notify us of any change of address, so we can keep you apprised of important information about safety, new
products, and new options that can increase your ability to use and enjoy your power chair. Please feel free to contact us
at the address below:
Pride Mobility Products Corporation
Attn: Customer Care Department
182 Susquehanna Avenue
Exeter, PA 18643-2694
customercare@pridemobility.com
800-424-8205
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact us and
we will be glad to send you a new one immediately.
4
www.quantumrehab.com
Quantum 610
I.
INTRODUCTION
PRIDE OWNERS CLUB
As an owner of a Pride product, you are invited to register your product’s warranty and enroll in the Pride Owners Club.
You may do so by filling out and returning your enclosed product registration card or by visiting Pride's web site at
www.pridemobility.com. As a registered member, each time you visit our site, you will have access to the most interactive
and honest educational venue available today for people with mobility needs, their families, and friends.
From our home page, select “Owners Club” to enter a page dedicated to current and potential Pride product owners. You
will gain access to interviews, stories, recreation ideas, daily living tips, product and funding information, and interactive
message boards. These message boards invite you to communicate with other Pride customers as well as Pride representatives who are available to assist you with any questions or concerns you may have.
My Quantum Rehab Specialist:
Name:_____________________________________________________________________________________
Address:___________________________________________________________________________________
Phone Number:______________________________________________________________________________
Purchase Date:_______________________________________________________________________________
Quantum 610
www.quantumrehab.com
5
II.
SAFETY
PRODUCT SAFETY SYMBOLS
The symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions. It is very
important for you to read and understand them completely.
Corrosive chemicals contained in battery. Use only AGM or Gel-Cell batteries to
reduce the risk of leakage or explosive conditions.
Read and follow the information in the owner’s manual.
Maximum seating weight.
Locked and in drive mode.
Place unit on level ground and stand behind or to one side when changing from
drive mode to freewheel mode or freewheel mode to drive mode.
Unlocked and in freewheel mode.
Battery Configuration:
T = Terminal Post
Connect Red wire to T with +
Connect Black wire to T with –
6
www.quantumrehab.com
Quantum 610
II.
SAFETY
Do not use a cell phone, walkie/talkie, laptop, or other radio transmitter while operating.
Avoid exposure to rain, snow, ice, salt, or standing water whenever possible. Maintain and
store in a clean and dry condition.
Removal of grounding prong can create electrical hazard. If necessary, properly install
an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access. Failure
to heed could result in personal injury and/or property damage.
Prevent personal injury and equipment damage. Do not connect an extension cord to the
AC/DC converter or the battery charger.
EMI-RFI - This product has been tested and passed at an immunity level of 20 V/m.
Quantum 610
www.quantumrehab.com
7
II.
SAFETY
SAFETY
MANDATORY! Do not operate your new power chair for the first time without completely reading
and understanding this owner’s manual.
Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive
variety of products to best fit the individual needs of the power chair user. Please be aware that the final selection and
purchasing decision regarding the type of power chair to be used is the responsibility of the power chair user, who is
capable of making such a decision, and his/her healthcare professional (i.e., medical doctor, physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted the power chair
to the user and has assisted the prescribing healthcare professional and/or the Quantum Rehab Specialist in the instruction
process for the use of the product.
There are certain situations, including some medical conditions, where the power chair user will need to practice operating
the power chair in the presence of a trained attendant. A trained attendant can be defined as a family member or care
professional specially trained in assisting a power chair user in various daily living activities.
As you begin using your power chair during daily activities, you will probably encounter situations in which you will need
some practice. Simply take your time and you will soon be in full and confident control as you maneuver through doorways,
on and off of elevators, up and down ramps, and over moderate terrain.
Below are some precautions, tips, and other safety considerations that will help the user become accustomed to operating
the power chair safely.
Modifications
Pride has designed and engineered your power chair to provide maximum mobility and utility. A wide range of accessories
is available from your Quantum Rehab Specialist to further customize your power chair to better suit your needs and/or
preferences. However, under no circumstances should you modify, add, remove, or disable any feature, part, or function
of your power chair.
WARNING! Do not modify your power chair in any way not authorized by Pride. Unauthorized
modifications may result in personal injury and/or damage to your power chair.
Pre-Ride Safety Check
Get to know the feel of your power chair and its capabilities. Pride recommends that you perform a safety check before
each use to make sure your power chair operates smoothly and safely.
Perform the following inspections prior to using your power chair:
! Check for proper tire inflation. Maintain but do not exceed 35 psi (2.4 bar) in each tire (if equipped with pneumatic tires).
! Check all electrical connections. Make sure they are tight and not corroded.
! Check all controller connections to the power base. Make sure they are secured properly.
! Check the brakes. See VIII. “Care and Maintenance.”
! Check battery charge. See VI. “Batteries and Charging.”
NOTE: If you discover a problem, contact your Quantum Rehab Specialist for assistance.
8
www.quantumrehab.com
Quantum 610
II.
SAFETY
Weight Limitations
Your power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit.
WARNING! Exceeding the weight capacity voids your warranty and may result in personal injury
and/or damage to your power chair. Pride will not be held responsible for injuries and/or property
damage resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your power chair. Carrying passengers on your power
chair may result in personal injury and/or property damage.
Tire Inflation
If your power chair is equipped with pneumatic tires, you should check or have the air pressure checked regularly. Proper
inflation pressures will prolong the life of your tires and help ensure the smooth operation of your power chair.
WARNING! It is important that 35 psi (2.4 bar) tire pressure be maintained in pneumatic tires at all
times. Do not underinflate or overinflate your tires. Low pressure may result in loss of control, and
overinflated tires may burst. Failure to maintain 35 psi (2.4 bar) tire pressure in pneumatic tires at
all times may result in tire and/or wheel failure, causing serious personal injury and/or damage to
your power chair.
WARNING! Inflate your power chair drive tires from a regulated air source with an available pressure
gauge. Inflating your tires from an unregulated air source could overinflate them, resulting in a
burst tire and/or personal injury.
Incline Information
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe access. Some ramps
may have turning switchbacks (180-degree turns) that require you to have good cornering skills on your power chair.
! Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
! Take wide swings with your power chair’s front wheels around any tight corners. If you do that, the power chair’s rear
wheels will follow a wide arc, not cut the corner short, and not bump into or get hung up on any railing corners.
! When driving down a ramp, keep the power chair’s speed adjustment set to the slowest speed setting to ensure a
safely controlled descent. See VII. “Operation.”
! Avoid sudden stops and starts.
When climbing an incline, try to keep your power chair moving. If you must stop, start up again slowly and then accelerate
cautiously. When driving down an incline, set your power chair to the slowest setting and drive in the forward direction
only. If your power chair starts to move down the incline faster than you anticipated or desired, allow it to come to a
complete stop by releasing the joystick, then push the joystick forward slightly to ensure a safely controlled descent.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of the incline.
Drive your power chair straight up the incline. This greatly reduces the possibility of a tip or a fall.
Always exercise extreme caution when negotiating an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e., areas covered
with snow, ice, cut grass, or wet leaves).
WARNING! When on any sort of an incline or decline, never place the power chair in freewheel
mode while seated on it or standing next to it. Doing so may result in personal injury and/or
damage to your power chair.
WARNING! Never travel down an incline backwards. This may result in personal injury.
Quantum 610
www.quantumrehab.com
9
II.
SAFETY
WARNING! Even though your power chair is capable of climbing slopes greater than those illustrated in
figure 1, do not, under any circumstances, exceed the incline guidelines or any other specifications
presented in this manual. Doing so could cause instability in your power chair, resulting in personal injury
and/or damage to your power chair.
In compliance with the Americans with Disabilities Act of 1990, all handicap public access ramps are required to have a
maximum slope of 5° (8.7%). Therefore, Pride recommends that the maximum slope of an incline you attempt to safely
ascend or descend on your power chair does not exceed 5° (8.7%). See figure 1.
WARNING! Any attempt to climb or descend a slope steeper than 5° (8.7%) may put your power
chair in an unstable position and cause it to tip, resulting in personal injury.
5 (8.7%)
Figure 1. Maximum Safe Slope (Ascending and Descending)
Braking Information
Your power chair is equipped with two powerful brake systems:
1. Regenerative — uses electricity to rapidly slow the vehicle when the joystick returns to the center/stop position.
2. Disc Park Brake — activates mechanically after regenerative braking slows the vehicle to near stop, or when power is
removed from the system for any reason.
Cornering Information
While your power chair is equipped with four caster wheels, excessively high cornering speeds can still create the possibility of tipping. Factors which affect the possibility of tipping include, but are not limited to: cornering speed, steering angle
(how sharply you are turning), uneven road surfaces, inclined road surfaces, riding from an area of low traction to an area
of high traction (such as passing from a grassy area to a paved area – especially at high speed while turning), and abrupt
directional changes. High cornering speeds are not recommended. If you feel that you may tip over in a corner, reduce
your speed and steering angle (i.e., lessen the sharpness of the turn) to prevent your power chair from tipping.
WARNING! When cornering sharply, reduce your speed. This greatly reduces the possibility of a
tip or fall. To avoid personal injury and/or property damage, always exercise common sense when
cornering.
Public Streets and Roadways
WARNING! You should not operate your power chair on public streets and roadways. Be aware
that it may be difficult for traffic to see you when you are seated on your power chair. Obey all
local pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed with extreme
caution.
Preventing Unintended Movement
WARNING! If you anticipate being seated in a stationary position for an extended period of time,
turn off the power. This will prevent unexpected motion from inadvertent joystick contact. This
will also eliminate the possibility of unintended chair movement from electromagnetic (EM) sources.
Failure to do so may result in personal injury.
10
www.quantumrehab.com
Quantum 610
II.
SAFETY
Freewheel Mode
Your power chair is equipped with two manual freewheel levers to allow for manual maneuverability by a trained attendant.
For more information about how to place your power chair into and out of freewheel mode, see III. “Your Power Chair.”
WARNING! Do not use your power chair in freewheel mode without an attendant present. Personal
injury may result.
WARNING! Do not attempt to personally place your power chair in freewheel mode while seated
on it. Personal injury may result. Ask an attendant for assistance if necessary.
WARNING! Do not place your power chair in freewheel mode while on an incline. The chair could
roll uncontrollably on its own, causing personal injury.
Outdoor Driving Surfaces
Your power chair is designed to provide optimum stability under normal driving conditions—dry, level surfaces composed
of concrete, blacktop, or asphalt. However, Pride recognizes that there will be times when you will encounter other surface
types. For this reason, your power chair is designed to perform admirably on packed soil, grass, and gravel. Feel free to
use your power chair safely on lawns and in park areas.
! Reduce your power chair’s speed when driving on uneven terrain and/or soft surfaces.
! Avoid tall grass that can entangle the running gear.
! Avoid loosely packed gravel and sand.
! If you feel unsure about a driving surface, avoid that surface.
Stationary Obstacles (Steps, Curbs, etc.)
Proceed with extreme caution when driving near raised surfaces, unprotected ledges and/or drop-offs (curbs, porches,
stairs, etc.). The correct method for approaching a curb is illustrated in figure 2.
WARNING! Do not attempt to have your power chair climb or descend an obstacle that is higher
than 2 inches unless you have the assistance of an attendant.
WARNING! Do not attempt to have your power chair proceed backwards down any step, curb, or
other obstacle. This may cause the power chair to tip and cause personal injury.
Figure 2. Correct Curb Approach
Figure 3. Incorrect Curb Approach
Stairs and Escalators
Power chairs are not designed to travel up or down stairs or escalators. Always use an elevator.
WARNING! Never use your power chair to negotiate steps or escalators. You may cause injury to
yourself and to others and/or damage your power chair.
Quantum 610
www.quantumrehab.com
11
II.
SAFETY
Transfers
Transferring onto and off of your power chair requires a
good sense of balance. Always have an attendant or healthcare professional present while learning to properly transfer yourself.
To eliminate the possibility of injury, Pride recommends that
you or a trained attendant perform the following tasks before attempting a transfer:
! Turn off the power to the controller. See VII. “Operation.”
! Ensure your power chair is not in freewheel mode. See
III. “Your Power Chair.”
! Turn the front caster wheels toward the transfer destination to improve power chair stability during transfer.
! Make sure both armrests are flipped up or removed
from your power chair.
! Flip up the foot platform or move the leg rests aside;
this will help to keep your feet from getting caught on
the foot rigging during the transfer.
! Reduce the distance between your power chair and the
object you are transferring onto.
Figure 4. Ideal Transfer Position
WARNING! Before transferring, position yourself as far back as possible in the power chair seat
to prevent the power chair from tipping forward during transfer and causing injury.
WARNING! Avoid using your armrests for weight bearing purposes. Such use may cause the power
chair to tip and cause personal injury.
WARNING! Avoid putting all of your weight on the foot riggings. Such use may cause the power
chair to tip and cause personal injury.
Doors
! Determine if the door opens toward or away from you.
! Drive your power chair gently and slowly forward to push the door open. Or drive your power chair gently and slowly
backwards to pull the door open.
Elevators
Modern elevators have a door edge safety mechanism that, when pushed, reopens the elevator door(s).
! If you are in the doorway of an elevator when the door(s) begin to close, push on the rubber door edge or allow the
rubber door edge to contact the power chair and the door will reopen.
! Use care that pocketbooks, packages, or power chair accessories do not become caught in elevator doors.
Lift/Elevation Products
If you will be traveling with your power chair, you may find it necessary to use a lift/elevation product to aid in transportation. Pride recommends that you closely review the instructions, specifications, and safety information set forth by the
manufacturer of the lift/elevation product before using that product.
12
www.quantumrehab.com
Quantum 610
II.
SAFETY
Inclement Weather Precautions
Exposure of your power chair to inclement weather conditions should be avoided whenever possible. If suddenly caught
up in rain, snow, severe cold, or heat while operating your power chair proceed to shelter at the earliest opportunity.
Thoroughly dry your power chair before storing, charging, or operating your power chair.
WARNING! Operating in rain, snow, salt, mist/spray conditions, and on icy/slippery surfaces can
cause personal injury and/or damage to the power chair and electrical system. Maintain and store
your power chair in a dry and clean condition.
Motor Vehicle Transport
Pride recommends that you do not remain seated in your power chair while traveling in a motor vehicle. The power chair
should be stowed in the trunk of a car or in the back of a truck or van with the batteries removed and properly secured.
WARNING! Do not sit on your power chair while it is in a moving vehicle. Personal injury and/or
property damage may result.
WARNING! Always be sure your power chair and its batteries are properly secured when it is being
transported. Failure to do so may result in personal injury and/or damage to your power chair.
Positioning Belts
Your Quantum Rehab Specialist, therapist(s), and other healthcare professionals are responsible for determining your
requirement for a positioning belt in order to operate your power chair safely.
WARNING! If you require a positioning belt to safely operate your power chair, make sure it is
fastened securely. Serious personal injury may result if you fall from the power chair.
WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle. Nor is
your power chair suitable for use as a seat in any vehicle. Anyone traveling in a vehicle should be
properly belted into seats approved by the vehicle manufacturer.
Reaching and Bending
Never reach, lean, or bend while driving your power chair. If it is absolutely necessary to reach, lean, or bend while seated
on your power chair, it is important to maintain a stable center of gravity and keep the power chair from tipping. Pride
recommends that the power chair user determine his/her personal limitations and practice bending and reaching in the
presence of a qualified healthcare professional.
WARNING! Do not bend, lean, or reach for objects if you have to pick them up from the floor by
reaching down between your knees. Movements such as these may change your center of gravity
and the weight distribution of the power chair. This may cause your power chair to tip, possibly
resulting in personal injury.
WARNING! Prevent personal injury! Keep your hands away from the tires when driving. Be aware
that loose fitting clothing can become caught in drive tires.
Quantum 610
www.quantumrehab.com
13
II.
SAFETY
Batteries
In addition to following the warnings below, be sure to comply with all other battery handling information. For more
information about your power chair’s batteries, see VI. “Batteries and Charging.”
WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that
much weight, be sure to get help. Lifting beyond your capacity can result in personal injury.
WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds.
Wash hands after handling.
WARNING! Always protect the batteries from freezing and never charge a frozen battery. Charging
a frozen battery may result in personal injury and/or damage to the battery.
Removable Parts
WARNING! Do not attempt to lift or move a power chair by any of its removable parts. Personal
injury and/or damage to the power chair may result.
Prescription Drugs/Physical Limitations
Users must exercise care and common sense when operating a power chair. This includes awareness of safety issues when
taking prescribed or over-the-counter drugs or when the user has specific physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter medication or
if you have certain physical limitations. Some medications and limitations may impair your ability
to operate your power chair in a safe manner.
Alcohol
The power chair user must exercise care and common sense when operating his/her power chair. This includes awareness
of safety issues while under the influence of alcohol.
WARNING! Do not operate your power chair while you are under the influence of alcohol, as this
may impair your ability to operate your power chair in a safe manner.
14
www.quantumrehab.com
Quantum 610
II.
SAFETY
Electromagnetic and Radio Frequency Interference (EMI/RFI)
WARNING! Laboratory tests have shown that electromagnetic and radio frequency waves can
have an adverse affect on the performance of electrically-powered mobility vehicles.
Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones, mobile two-way
radios (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters, wireless computer links,
microwave signals, paging transmitters, and medium-range mobile transceivers used by emergency vehicles. In some
cases, these waves can cause unintended movement or damage to the control system. Every electrically-powered mobility
vehicle has an immunity (or resistance) to EMI. The higher the immunity level, the greater the protection against EMI. This
product has been tested and has passed at an immunity level of 20 V/m.
WARNING! Be aware that cell phones, two-way radios, laptops, and other types of radio transmitters
may cause unintended movement of your electrically-powered mobility vehicle due to EMI.
Exercise caution when using any of these items while operating your mobility vehicle and avoid
coming into close proximity of radio and TV stations.
WARNING! The addition of accessories or components to the electrically-powered mobility vehicle
can increase the susceptibility of the vehicle to EMI. Do not modify your power chair in any way
not authorized by Pride.
WARNING! The electrically-powered mobility vehicle itself can disturb the performance of other
electrical devices located nearby, such as alarm systems.
NOTE: For further information on EMI/RFI, go to the Resource Center on www.pridemobility.com. If unintended motion or brake release occurs, turn your power chair off as soon as it is safe to do so. Call Pride at 800424-8205 to report the incident.
Quantum 610
www.quantumrehab.com
15
III.
YOUR
POWER
CHAIR
THE QUANTUM 610
The Quantum 610 has two main assemblies: the seat assembly and the power base assembly. See figure 5. Typically, the
seat assembly includes the armrests, seatback, and seat base. The power base assembly includes two motor/brake assemblies, two drive wheels, four caster wheels, two batteries, and wiring harnesses. See figure 5, 6, and 7.
SEATBACK
ARMRESTS
SEAT ASSEMBLY
CONTROLLER
(FLIGHT SHOWN)
SEAT BASE
POWER BASE
ASSEMBLY
REAR
SHROUD
CASTER WHEEL
DRIVE WHEEL
FOOT RIGGING
(FOOT PLATFORM SHOWN)
CASTER WHEEL
Figure 5. The Quantum 610
16
www.quantumrehab.com
Quantum 610
III.
YOUR
POWER
CHAIR
QUANTUM 610 SPECIFICATIONS
Suspension:
Active-Trac Extreme (ATX)
Drive Wheels:
10 in., pneumatic (10 in. solid optional)
Front Caster Wheels:
5 in., solid
Rear Caster Wheels:
6 in., solid
Maximum Speed:
Up to 4.5 mph¹
Brakes:
“Intelligent Braking” electronic regenerative, disc park brake
Ground Clearance:
2.5 in.²
Turning Radius:
21.25 in.²
Overall Size:
Length: 39 in. (with foot platform)²
Width: 23.25 in.²
Seating Options:
Specialty Seat
Medium-Back Seat with Solid Seat Pan
Limited Recline High-Back Seat with Solid Seat Pan
Full Recline High-Back Seat with Solid Seat Pan
Power Elevating Seat
Synergy Seat
Synergy Manual Recline
Synergy Manual Tilt
Synergy TRU-Balance Power Positioning Systems
Drivetrain:
Two motor, mid-wheel-6 drive
Range:
Up to 25 miles¹
Batteries:
Two 12-volt, U-1 batteries (AGM or Gel-Cell type recommended)
Battery Charger:
5-amp, off-board (standard)
4-amp onboard/5-amp off-board combo (optional)
Electronics:
75-amp Dynamic FLIGHT Controller
70-amp PG Drives VSI Controller
70-amp PG Drives Remote Plus
70-amp Microdrive
Weight Capacity:
300 lbs.
160 lbs. with Synergy Manual Tilt
200 lbs. with Synergy TRU-Balance Power Positioning Systems
Component Weights:
Base: 112 lbs. (without seat and batteries)
Specialty Seat: 37 lbs.
Batteries: 24.5 lbs. each
¹Varies with user weight, terrain type, battery amp hour rating (AH), battery charge, battery condition, and tire condition.
²Due to manufacturing tolerances and continued product improvement, this specification can be subject to varianceof (+ or – ) 3%.
NOTE: All specifications subject to change without notice.
Quantum 610
www.quantumrehab.com
17
III.
YOUR
POWER
CHAIR
REAR SHROUD FASTENERS
TRAPEZE BARS
FRONT COVER
MOTOR/BRAKE ASSEMBLY
Figure 6. The Quantum 610 Power Base
ELECTRICAL COMPONENTS
The electrical components are located inside the power base. The ammeter and the charger power cord receptacle for the
optional onboard charger are located on the right side of the power base. The main circuit breaker is located on the front
of the battery tray. The controller connector(s) are located inside the power base. See figure 7.
Ammeter (optional onboard charger only): The ammeter displays the charger’s current output in amps. See VI. “Batteries and Charging.”
Charger Power Cord Receptacle (optional onboard charger only): This is where the charger power cord plugs into
the onboard battery charger. See VI. “Batteries and Charging.”
Motor Connectors: This is where the controller connects to the motors.
18
www.quantumrehab.com
Quantum 610
III.
YOUR
POWER
CHAIR
Battery Connector: This is where the controller connects to the batteries.
Charger Inhibit Connector (optional onboard charger only): The charger inhibit enables the onboard battery charger
to disable the controller during charging. See VII. “Operation.”
Controller Connector: This is where the controller connects to the power base.
Main Circuit Breaker: The main circuit breaker is a safety feature built into your power chair. When the batteries and the
motors are heavily strained (e.g., from excessive loads), the main circuit breaker trips to prevent damage to the motors and
the electronics. If the circuit trips, allow your power chair to “rest” for approximately one minute. Next, push in the circuit
breaker button, turn on the controller, and continue normal operation. If the main circuit breaker continues to trip repeatedly, contact your Quantum Rehab Specialist.
CHARGER INHIBIT CONNECTOR
FLIGHT POWER MODULE
CHARGER CIRCUIT FUSE
CONTROLLER CONNECTOR
BATTERY
CONNECTOR
MOTOR
CONNECTORS
BATTERY
CONNECTOR
MOTOR
CONNECTORS
VSI CONTROLLER
ONBOARD BATTERY
CHARGER
CHARGER POWER
CORD RECEPTACLE
AMMETER
MAIN CIRCUIT BREAKER
Figure 7. Quantum 610 Electrical Components (Shown With Optional Onboard Battery Charger)
Quantum 610
www.quantumrehab.com
19
III.
YOUR
POWER
CHAIR
Manual Freewheel Levers
The Quantum 610 has a manual freewheel lever on each motor. Manual freewheel levers enable you to disengage the drive
motors from the gearboxes and maneuver the chair manually.
WARNING! Do not use the power chair while the drive motors are disengaged! Do not disengage
the drive motors when the power chair is on an incline, as the unit could roll on its own, causing
injury!
To engage or disengage the drive motors:
1. Locate the lever on top of each motor.
2. Push the two levers inward to engage the drive motors. See figure 8.
3. Pull the two levers outward to disengage the drive motors. See figure 9.
If a lever is difficult to move in either direction, slightly rock the power chair back and forth. The lever should then move to
the desired position.
WARNING! It is important to remember that when your power chair is in freewheel mode, the
braking system is disengaged.
MANUAL FREEWHEEL LEVER
Figure 8. Drive Mode (Drive Engaged)
20
MANUAL FREEWHEEL LEVER
Figure 9. Freewheel Mode (Drive Disengaged)
www.quantumrehab.com
Quantum 610
I V.
ASSEMBLY
INITIAL ASSEMBLY
Your power chair may require some assembly either before initial use or after transportation. It may also require disassembly
to make some comfort adjustments. Figure 10 details those parts of the power chair that are designed to be disassembled and
assembled by an end user or by a qualified caregiver before using the product or making comfort adjustments.
NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be
replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon
insert, resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores
or through your Quantum Rehab Specialist.
ARMREST ANGLE ADJUSTMENT
SEAT INSTALLATION
SEAT HEIGHT/ANGLE ADJUSTMENT
CONTROLLER POSITION
FOOT PLATFORM
ANGLE ADJUSTMENT
FOOT PLATFORM HEIGHT/DEPTH ADJUSTMENT
Figure 10. Quantum 610 Assembly View (Universal Mounting System Shown)
Quantum 610
www.quantumrehab.com
21
I V.
ASSEMBLY
Seat Installation
It may be necessary to install the seat either prior to initial
operation or after transporting your power chair. Most seats
are attached to the power base with the Universal Mounting System (UMS). The UMS consists of universal parts
that may be attached to any medium-back or high-back
seat, regardless of seat width or seat depth. The two main
components are aluminum extrusions mounted to the seat
base. These extrusions attach to a pair of trapeze bars that
are mounted to the power base. See figure 11. If your power
chair is equipped with a Synergy Seating System or a Synergy TRU-Balance Power Positioning System, refer to the
information provided in separate manuals.
REAR
EXTRUSION
SEAT
LATCH
SAFETY
WARNING! Do not pick up the seat frame
by the armrests. They are free to pivot,
and you may lose control of the seat if
they do so, resulting in personal injury
or damage to the chair.
To install the seat:
1. Tilt the seat back and slide the rear extrusion onto the
rear trapeze bar. See figure 11.
2. Lower the front extrusion onto the front trapeze bar
until the seat locks into place.
3. Flip the seat latch safety down. See figure 11.
WARNING! Make sure the seat latch
safety is flipped down before using your
power chair.
REAR TRAPEZE
BAR
Figure 11. Universal Mounting System (FLIGHT Shown)
4. Install the controller and route the cable to the back of
the power base. See figure 12.
5. Loosen the rear shroud fasteners counterclockwise onequarter turn and remove the rear shroud. See figure 6.
6. Plug the controller connector into the power base. See
figure 7.
7. Reinstall the rear shroud. Turn the rear shroud fasteners
clockwise one-quarter turn. See figure 6.
8. Route the controller cable so that it cannot be pinched
in the seat hinge.
9. Secure the controller cable to the armrest receiver with
wire ties. See figure 13.
Figure 12. Remote Plus Controller Routed on a Synergy
Seat
22
www.quantumrehab.com
Quantum 610
I V.
ASSEMBLY
Power Seat Option Installation
Your power chair may be equipped with the power seat option.
While the seat itself may be any one of the styles offered for this
model, the way the seat base attaches to the power base is different.
WIRE TIES
To install the power seat:
l. Align the post on the bottom of the power seat base over
the hole in the power seat actuator.
2. Slide the post into the actuator and push the friction lock
lever forward.
3. Connect the power seat cable to the power base.
4. Tilt the seat back and slide the rear extension onto the power
seat base.
5. Lower the front extrusion onto the power seat base until
the seat locks into place.
6. Flip down the seat latch safety.
7. Install the controller.
NOTE: Refer to V. “Comfort Adjustments” for more information on controller installation and adjustment.
Figure 13. Remote Plus Controller Routed on a
Contour Seat
FRICTION LOCK
LEVER
POWER SEAT
ACTUATOR
Figure 14. Power Seat Actuator
Quantum 610
www.quantumrehab.com
23
V.
COMFORT
ADJUSTMENTS
COMFORT ADJUSTMENTS
After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase
your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and controller position. If your
power chair is equipped with a specialty seat, refer to the information provided in separate manuals. If your power chair is
equipped with a medium-back, a high-back, or a reclining seat, refer to the following information.
WARNING! If your power chair was configured by your Quantum Rehab Specialist, please consult your
healthcare professional before changing the seat position or making any other adjustment. Some
adjustments may degrade your power chair’s performance and safety by changing its center of gravity.
WARNING! Some power chair components are heavy. You may need assistance to lift or carry
them. Please refer to the specifications table for specific component weights before you
disassemble the power chair.
WARNING! Prevent injury. Remove the occupant from the power chair before making any
adjustments.
You may need the following to make comfort adjustments:
! metric/standard socket set and ratchet
! adjustable wrench
! thread lock
Seat Height and Seat Angle Adjustment
You can change the seat height to one of four positions in 1in. increments by raising the front and rear trapeze bars. If
you raise or lower only one trapeze bar (front or rear), you
can also change the seat base angle (dump).
Figure 15. Seat Height Adjustment - Seat Latch Safety
To change the seat height:
1. Turn off the power to the controller.
2. Unlock the rear shroud fasteners and remove the rear
shroud. See figure 6.
3. Disconnect the controller connector(s) from the power
base. See figure 7.
4. Flip up the seat latch safety. See figure 15.
5. Squeeze the seat latch and release the seat from the front
trapeze bar. See figure 15.
6. Slide the seat forward and remove it from the power base.
7. Loosen the screws that attach the trapeze bars to the seat
posts. See figure 16.
8. Remove the retaining clips that secure the seat posts to
the power base. See figure 16.
9. Move the trapeze bars up or down to the desired height.
10. Reinstall the retaining clips from step 8.
11. Remove each screw from the trapeze bars and apply
thread lock.
12. Reinstall each screw into the trapeze bars and tighten.
13. Reinstall the seat and flip down the seat latch safety.
SCREWS
TRAPEZE BARS
SEAT POSTS
SEAT POSTS
RETAINING
CLIPS
RETAINING
CLIPS
Figure 16. Seat Height Adjustment - Trapeze Bars
24
www.quantumrehab.com
Quantum 610
V.
COMFORT
ADJUSTMENTS
14. Reconnect the controller connector(s) to the power base.
15. Reinstall the rear shroud and tighten the fasteners.
Seat Position
You can move the seat forward or rearward by changing
the extrusion mounting position.
To change the position:
1. Turn off the power to the controller.
2. Unlock the rear shroud fasteners and remove the rear
shroud. See figure 6.
3. Unplug the controller connector(s) from the power base.
4. Remove the seat from the power base.
5. Remove both extrusions from the bottom of the seat.
6. Reposition the extrusions on a different set of mounting
holes. You must move both extrusions the same number
of holes either forward or backwards. See figure 17.
7. Fasten the extrusions back onto the bottom of the seat.
8. Reinstall the seat.
9. Reconnect the controller.
10. Reinstall the rear shroud and tighten the fasteners.
Figure 17. Seat Position Adjustment
ARMREST ANGLE ADJUSTING SCREW
Seatback Angle Adjustment
If your power chair is equipped with an adjustable seatback,
you can adjust it to four (4) different angles: 90°, 102°,
105°, or 107°.
To adjust the seatback angle:
1. Remove the adjusting screws from each seat hinge. See
figure 18.
2. Set the seatback at the desired angle.
3. Reinstall the adjusting screws to each seat hinge and tighten.
Manual Recline Seatback Adjustment
If your power chair is equipped with a reclining seat, you
can adjust the seatback angle with the seatback release
lever. The lever is located on the right side of the seat base.
JAM
NUTS
SEATBACK
ANGLE
ADJUSTING
SCREW
ARMREST KNOB
To adjust the recline angle:
1. Pull up on the seatback release lever.
2. Lean forward or backwards to the desired position.
3. Release the lever.
Quantum 610
Figure 18. Seatback Angle Adjustment
www.quantumrehab.com
25
V.
COMFORT
ADJUSTMENTS
Armrest Width Adjustment
You can change each armrest’s width independently of the other.
NOTE: Changing the armrest width may increase the
overall width of your power chair.
To change the armrest width:
1. Locate the two armrest knobs on each side of the armrest receiver bracket. See figure 18.
2. Loosen the knobs.
3. Slide the armrests in or out to the desired width.
4. Tighten the knobs.
Armrest Angle Adjustment
To change the armrest angle:
1. Lift the armrest straight up so that it is perpendicular to
the floor. See figure 18.
2. Loosen the jam nuts.
3. Turn the adjusting screw clockwise to lower the front
of the armrest, or turn the adjusting screw counterclockwise to raise the front of the armrest.
4. Tighten the jam nuts to lock the adjusting screw into
place.
FOOT PLATFORM
RETAINING PIN
SECUREMENT NUT
FOOT
PLATFORM
BRACKET
QUICK
RELEASE
FASTENERS
SETSCREW
Figure 19. Foot Platform Adjustment
SETSCREW
Controller Position
You can position the controller for either left-hand or righthand use.
WARNING! Do not place the controller cable
so that it can be pinched in the seat frame
or the power base frame.
To change the controller position:
1. Turn off the power to the controller.
Figure 20. Underside of Armrest (Contour Seat)
2. Turn the rear shroud fasteners counterclockwise onequarter turn. See figure 6.
3. Remove the rear shroud.
4. Unplug the controller connector(s) from the power base.
5. Cut the wire tie(s) securing the controller cable to the armrest. See figure 6.
6. Loosen the mounting screws in the mounting block. See figure 21.
7. Move the controller mounting block and controller to the other armrest and tighten the mounting screws.
NOTE: For contour seats, loosen the setscrew on the underside of both armrests, transfer the controller, and
tighten the setscrews. See figure 20.
8. Route the controller cable to the back of the power base and plug in the controller. See figure 12.
9. Use wire ties to secure the controller cable to the seat frame. See figure 13.
26
www.quantumrehab.com
Quantum 610
V.
COMFORT
ADJUSTMENTS
10. Plug the controller connector(s) into the power base.
11. Reinstall the rear shroud and tighten the fasteners.
MOUNTING
SCREWS
MOUNTING
BLOCK
Foot Platform Height Adjustment
The foot platform height is easily adjusted to different heights
in 1/2-in. increments.
To raise or lower the foot platform:
1. Remove the quick release fasteners from the foot platform bracket. See figure 19.
2. Loosen the foot platform securement nut one-half turn.
3. Raise or lower the foot platform to the desired height.
4. Reinstall the quick release fasteners into the foot platform bracket and tighten.
5. Tighten the nut to secure.
Figure 21. Mounting Block Controller Installation
Foot Platform Depth Adjustment
To adjust the foot platform depth:
1. Remove the quick release fasteners from the foot platform bracket. See figure 19.
2. Move the foot platform in or out to the desired depth.
3. Reinstall the quick release fasteners into the foot platform bracket and tighten.
Quick Release Fasteners: The foot platform is attached
to the power base with two quick release fasteners. See
figure 19. Each quick release fastener consists of a bolt, a
lever, and a nut. See figure 22. The lever has a cam on the
end that allows it to clamp into place. The quick release
fastener has two states: clamped and unclamped. When the
lever is open, the quick release fastener is unclamped. When
the lever is closed, the quick release fastener is clamped.
LEVER (FULLY CLOSED)
CAM
BOLT
NUT
CLAMPED
UNCLAMPED
LEVER (OPEN)
Figure 22. Quick Release Fastener Operation
To clamp the quick release fastener:
1. Make sure the lever is in the open position.
2. Turn the nut clockwise until it is snug.
3. Rotate the lever until it is in the fully closed position.
NOTE: If the lever will not rotate to the fully closed
position, then turn the nut counterclockwise one-quarter or one-half turn.
Foot Platform Angle Adjustment
You can adjust the angle of the foot platform with a hex key.
To adjust the foot platform angle:
1. Flip up the foot platform and locate the setscrew and
jam nut. See figure 23.
Quantum 610
JAM NUT
SETSCREW
Figure 23. Underside of Foot Platform
www.quantumrehab.com
27
V.
COMFORT
ADJUSTMENTS
2. Loosen the jam nut.
3. Turn the setscrew counterclockwise to raise the front
of the foot platform or clockwise to lower the front of
the foot platform.
4. Tighten the jam nut to secure the setscrew.
Swing-away Footrests
Swing-away Footrests (SFRs) enable you to rotate the footrests to the side before you transfer onto or off or your power
chair. See figure 24.
To rotate the SFRs:
1. Push in the release lever.
2. Rotate the SFRs.
SFR RELEASE LEVER
FOOTREST
EXTENSION
ADJUSTMENT
SCREWS
Figure 24. Swing-Away Footrests
To adjust the SFR length:
1. Remove the two adjustment screws from the side of
each footrest extension.
2. Slide the footrest up or down to the desired length.
3. Reinstall the two adjustment screws.
Elevating Leg Rests
Elevating Leg Rests (ELRs) offer an infinite range of adjustment for the leg angle and a footrest adjustment range
of 12–19 in. See figure 25.
RELEASE LEVER A
RELEASE LEVER B
LEG REST
EXTENSION
ADJUSTMENT
SCREWS
To rotate the ELRs:
1. Push in release lever A.
2. Rotate the ELRs.
Figure 25. Elevating Leg Rests
To adjust the ELR angle:
1. Push down release lever B.
2. Move the leg rest to the desired angle.
To adjust the ELR length:
1. Remove the two adjustment screws from the side of
each leg rest extension.
2. Slide the leg rest up or down to the desired length.
3. Reinstall the two adjustment screws.
Heavy Duty Drop-in Leg Rests
You can adjust the forward/back position, as well as the
length of the heavy duty drop-in leg rests. See figure 26.
ADJUSTMENT
BOLT
LEG REST HANGER
LEG REST EXTENSION
LEG REST
ADJUSTMENT SCREWS
Figure 26. Heavy Duty Drop-In Leg Rests
28
www.quantumrehab.com
Quantum 610
V.
COMFORT
ADJUSTMENTS
To adjust the forward/back position:
1. Remove the adjustment bolts from the side rails.
2. Move the leg rest hanger in or out to the desired
position.
3. Align the adjustment holes in the leg rest hanger with
those in the side rail.
4. Reinstall the adjustment bolts to secure the leg rest
hangers.
A
B
To adjust the leg rest length:
1. Remove the adjustment screws from the leg rest extension.
2. Slide the leg rest up or down to the desired length.
3. Align the adjustment holes in the leg rest extension and
reinstall the adjustment screws.
Multi-Axis Foot Plates
The multi-axis foot plate assembly can be installed on either
a swing-away footrest or an elevating leg rest. The multiaxis foot plate has four adjustments: leg rest length (A),
position (B), tilt (C), and angle (D). See figure 27.
C
D
A
To change leg rest length (A):
1. Remove the hardware.
2. Move the leg rest to the desired position.
3. Reinstall the hardware.
B
To change foot plate position (B):
1. Remove the hardware.
2. Move the foot plate to the desired position.
3. Reinstall the hardware.
C
To change foot plate tilt (C):
1. Loosen the hardware.
2. Tilt the foot plate to the desired position.
3. Tighten the hardware.
To change foot plate angle (D):
1. Turn the setscrew clockwise to decrease the angle.
2. Turn the setscrew counterclockwise to increase the
angle.
D
SETSCREW LOCATION
Figure 27. Multi-Axis Foot Plate (ELR Shown)
Quantum 610
www.quantumrehab.com
29
V.
COMFORT
ADJUSTMENTS
Power Elevating Seat (Optional)
If your power chair is equipped with a power elevating seat, you
can change the seat height either through the controller or through a
toggle switch mounted to one of the armrests.
To change the seat height through toggle switch:
1. Press forward on the toggle switch to raise the seat. See
figure 28.
2. Pull back on the toggle switch to lower the seat.
WARNING! Do not allow the motor to run more
than a few seconds after the mechanism
reaches the top or bottom limit.
NOTE: For more information on operating the power elevating seat through the controller, contact your Quantum
Rehab Specialist.
WARNING! The power elevating seat option is
intended for use on a level surface only. Never
raise the seat from its lowest position on an
inclined surface. Failure to heed this warning
can result in the power chair tipping over and
causing injury.
Figure 28. Power Seat Toggle Switch
WARNING! Never raise the seat from its lowest position when operating your power chair
on bumpy or uneven surfaces. Failure to heed
this warning can result in the power chair tipping over and causing injury.
WARNING! Never raise the power elevating seat
while your power chair is in the freewheel
mode.
WARNING! Always fasten the positioning belt
when operating the power elevating seat.
NOTE: The power elevating seat option is equipped with a
system that reduces the speed of the power chair by one half
when the seat is elevated more than 1–2 inches. Always check
to be sure this system is operating properly before using your
power chair.
30
www.quantumrehab.com
Quantum 610
VI.
BATTERIES
AND
CHARGING
BATTERIES AND CHARGING
The Quantum 610 uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free.
Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a
longer and deeper discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable.
Automotive batteries are not designed to handle a long, deep discharge, and also are unsafe for use in power chairs.
WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds.
Wash hands after handling.
WARNING! Prevent injury and/or equipment damage! Do not use batteries that exceed the
recommended type and amp-hour capacity. Do not use batteries with different amp-hour capacities.
Refer to specifications table in this manual and in the manual suppled with the battery charger
for recommended type and capacities.
Charging the Batteries
The battery charger is essential in providing long life for your power chair batteries. It is designed to optimize your power
chair’s performance by charging the batteries safely, quickly, and easily. The battery charging system consists of the battery
charger, the charger circuit fuse, and the ammeter (optional onboard chargers only). The ammeter indicates the rate of
charge necessary to fully recharge the batteries. It is also a good indication of whether or not the charger is working. The
ammeter and the charger are only functional when the charger power cord is plugged into an electrical outlet. The charger
circuit has an ATO fuse that protects the ammeter. See figure 7.
PROHIBITED! Removal of grounding prong can create electrical hazard. If necessary, properly
install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access. Failure
to heed could result in personal injury and/or property damage.
PROHIBITED! Never use an extension cord to plug in your battery charger. Plug the charger directly
into a properly wired standard electrical outlet.
WARNING! You must recharge your power chair’s batteries with the supplied off-board charger or
optional onboard battery charger. Do not use an automotive-type battery charger.
WARNING! Prevent injury and/or equipment damage! Read the battery charging instructions in
this manual and in the manual supplied with the battery charger before charging the batteries.
WARNING! Prevent injury and/or equipment damage! Do not expose the off-board battery charger
to rain or other sources of moisture unless it has been tested for outdoor use. Refer to the manual
supplied with the battery charger for more information.
WARNING! Prevent injury and/or equipment damage! Explosive gases may be generated while
charging the batteries. Keep the power chair and battery charger away from sources of ignition
such as flames or sparks and provide adequate ventilation when charging the batteries.
WARNING! Prevent injury and/or equipment damage! Inspect the battery charger, wiring, and
connectors for damage before each use. Contact your Quantum Rehab Specialist if damage is
found.
WARNING! Prevent injury and/or equipment damage! Do not attempt to open the battery charger
case. If the battery charger does not appear to be working correctly, contact your Quantum
Rehab Specialist.
WARNING! Prevent injury and/or equipment damage! If the off-board battery charger is equipped
with cooling slots, then do not attempt to inset objects through these slots.
WARNING! Prevent injury and/or equipment damage! Do not allowed unsupervised children to
play near the power chair while the batteries are charging.
Quantum 610
www.quantumrehab.com
31
VI.
BATTERIES
AND
CHARGING
WARNING! Prevent injury and/or equipment damage! If your off-board battery charger has not
been tested and approved for outdoor use, then do not expose it to adverse or extreme weather
conditions. If the battery charger is exposed to adverse or extreme weather conditions, then it
must be allowed to adjust to the difference in environmental conditions before use indoors. Refer
to the manual suppled with the battery charger for more information.
To charge the batteries using the off-board charger:
1. Position your power chair next to a standard electrical outlet.
2. Be certain the controller power is turned off.
3. Plug the off-board charger into the off-board charger/programming socket on the controller. See VII. “Operation.”
4. Plug the off-board charger into the electrical outlet.
NOTE: If it is a Pride off-board charger, then there are two lights in it. The red light indicates that power to
the off-board charger is on. The green light indicates that the batteries are fully charged. If it is not a Pride offboard charger, then follow the instructions supplied by the manufacturer.
5. When the batteries are fully charged, unplug the off-board charger from the electrical outlet and then from the controller.
To charge the batteries using the optional onboard charger:
1. Position the rear of your power chair close to a standard electrical outlet.
2. Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your
Power Chair.”
3. Plug the charger power cord into the charger power cord receptacle on the power base, then into the electrical outlet.
NOTE: The power chair incorporates an inhibit function that disables the power chair when the charger is
plugged into an electrical outlet.
4. We recommend you charge the batteries for 8 to 14 hours. As the batteries charge, the ammeter needle slowly drops
to 0.
NOTE: The ammeter indicates how much charge is needed to fully charge the batteries. As the batteries
charge, the ammeter needle slowly drops to 0. When the batteries are fully charged, the needle vibrates on or
about the 0 mark on the ammeter.
5. When your power chair’s batteries are fully charged, disconnect the charger power cord, wind up the cord, and store
it in a safe place.
Battery Break-in
To break in new batteries for maximum efficiency:
1. Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak performance level.
2. Operate your power chair throughout the house and yard. Move slowly at first, and do not travel too far until you become
accustomed to the controls and break in the batteries.
3. Give the batteries another full charge of 8 to 14 hours and operate your power chair again. The batteries will now perform at over
90% of their potential.
4. After four or five charging cycles, the batteries will top off at 100% charge and last for an extended period.
32
www.quantumrehab.com
Quantum 610
VI.
BATTERIES
AND
CHARGING
Frequently Asked Questions (FAQs)
How does the charger work?
The battery charger takes the standard electrical outlet voltage of 120 VAC (alternating current) and converts it to 24
VDC (direct current). The power chair batteries use direct current to run your power chair. When the battery voltage is
low, the charger works harder to charge the battery. As the battery voltage approaches full charge, the charger doesn’t
work as hard to complete the charging cycle. This explains why the ammeter drops as it approaches a full charge. This is
how the charger maintains a charge but does not overcharge the battery.
Can I use a different battery charger?
You should use the charger supplied with the power chair. It is the safest, most efficient tool to charge the batteries. We do
not recommend using other types of chargers (e.g., an automotive battery charger).
NOTE: Your power chair’s charger will not operate after the batteries have been discharged to nearly zero
voltage. If this happens, call your Quantum Rehab Specialist for assistance.
How often must I charge the batteries?
Many factors come into play when deciding how often to charge the batteries. You may use your power chair all day on a
daily basis or you may not use it for weeks at a time.
! Daily Use
If you use your power chair on a daily basis, charge the batteries as soon as you are finished using your power chair.
Your power chair will be ready each morning to give you a full day’s service. It is recommended that you charge the
batteries 8 to 14 hours after daily use.
! Infrequent Use
If you use your power chair infrequently (once a week or less), you should charge the batteries at least once per week
for 12 to 14 hours.
NOTE: Keep your batteries fully charged and avoid deeply discharging your batteries. Do not charge the
batteries for more than 24 hours at a charging cycle.
How can I get maximum range or distance per charge?
Rarely do you have an ideal driving situation such as smooth, flat, hard terrain with no wind, hills, or curves. More often you
are presented with hills, sidewalk cracks, uneven and loosely packed surfaces, curves, and wind. All of these factors will
affect the distance or running time per battery charge. Below are a few suggestions for obtaining the maximum range per
charge:
! Always charge the batteries fully prior to your trip.
! Plan your trip in advance to avoid inclines if possible.
! Limit baggage weight to essential items.
! Try to maintain an even speed and avoid stop-and-go driving.
What type of batteries should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. Both AGM and Gel-Cell are deep-cycle
batteries that are similar in performance. Refer to the Specifications Table for more information regarding the batteries used
with your power chair.
Quantum 610
www.quantumrehab.com
33
VI.
BATTERIES
AND
CHARGING
WARNING! Corrosive chemicals contained in batteries. Use only AGM or Gel-Cell batteries to
reduce the risk of leakage or explosive conditions.
Why do my new batteries seem weak?
Deep-cycle batteries employ a much different chemical technology than that used in car batteries, nickel-cadmium (nicads),
or in other common battery types. Deep-cycle batteries are specifically designed to provide power, drain down their
charge, and then accept a relatively quick recharge. AGM and Gel-Cell batteries should be charged as often as possible.
They do not have a “memory” like nickel-cadmium batteries.
We work closely with our battery manufacturer to provide a battery that best suits your power chair’s specific demands.
Fresh batteries arrive regularly at Pride and are promptly shipped with a full charge. During shipping, the batteries encounter temperature extremes that may influence initial performance. Heat robs the charge from the battery, and cold slows the
power available and extends the time needed to recharge the battery (just as with a car battery).
It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature. More
importantly, it will take a few “charging cycles” (a partial drain— then a full recharge) to establish the critical chemical
balance that is essential to the battery’s peak performance and long life. It will be well worth it to take the time to break in
your battery properly.
NOTE: The useful life of a battery is quite often a reflection of the care it receives.
How can I ensure maximum battery life?
A fully charged deep-cycle battery will provide reliable performance and extended battery life. Keep your power chair’s
batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequently charged, or
stored without a full charge may be permanently damaged, causing unreliable power chair operation and limited battery life.
How should I store my power chair and its batteries?
If you do not use your power chair regularly, we recommend maintaining battery vitality by charging the batteries at least
once per week.
If you do not plan on using your power chair for an extended period, fully charge the batteries prior to storage. Disconnect
the battery harnesses and store the power chair in a warm, dry environment. Avoid temperature extremes, such as freezing
and excessively hot conditions, and never attempt to charge a frozen battery. A cold or frozen battery should be warmed
for several days prior to recharging.
What about public transportation?
AGM and Gel-Cell batteries are designed for application in power chairs and other mobility vehicles. These batteries are
Federal Aviation Administration (FAA) approved, allowing safe transportation on aircraft, buses, and trains, as there is no
danger of spillage or leakage. We suggest you contact the carrier’s ticket counter in advance to determine that carrier’s
specific requirements.
What about shipping?
If you wish to use a freight company to ship your power chair to your final destination, repack your power chair in the
original shipping container and ship the batteries in separate boxes.
34
www.quantumrehab.com
Quantum 610
VII.
OPERATION
FLIGHT CONTROLLER
The electronic controller is what you use to operate your power chair. It takes the battery voltage and sends it to the
appropriate system. The electronic controller enables you to move the power chair, as well as monitor battery charge,
electronic controller functions, and the condition of your electrical system. The FLIGHT is part of a modular electronic
controller system. The system consists of more than one module. Typically, the FLIGHT is mounted to one of the armrests.
See figure 29. It is connected to a power module located on the power base through the controller communications cable.
The FLIGHT may be used to control some optional systems, such as lights.
The controller supplied with your power chair has been pre-programmed to meet your needs. The program is set using
either a personal computer with software provided by the controller manufacturer or with a hand-held programmer, also
provided by the controller manufacturer.
WARNING! The controller program can affect speed, acceleration, deceleration, and braking. If it
is programmed incorrectly or outside of the safe limits as determined by your healthcare
professional, it can create a dangerous situation. Only the power chair manufacturer, an authorized
representative of the manufacturer, or a trained service technician should program the controller.
The FLIGHT consists of:
1. joystick
2. keypad
3. off-board charger/programming socket
4. controller connector
5. controller power module
2
1
3
Joystick
The joystick controls the direction and speed of your power
chair. When you move the joystick from the neutral (center)
position, the electromagnetic brakes release and allow your
power chair to move. The farther you push the joystick
from its neutral position, the faster your power chair moves.
When you release the joystick and allow it to return to the
neutral position, you engage the electromagnetic brakes.
This causes your power chair to decelerate and come to a
complete stop.
WARNING! If your power chair begins
to move in an unexpected manner, immediately release the joystick. Unless
the joystick is damaged, this action
should stop your power chair.
4
5
Keypad
The keypad is located in front of the joystick. It contains
keys necessary to operate your power chair. See figure 30. Figure 29. FLIGHT Controller
Horn Key
The horn key activates the horn.
Quantum 610
www.quantumrehab.com
35
VII.
OPERATION
On/Off Key
The on/off key turns the FLIGHT on and off.
WARNING! Unless faced with an emergency situation, do not use the on/off
key to stop the chair. This will cause
the power chair to stop abruptly.
WARNING! Always turn the power off
when you are stationary to prevent unexpected movement.
Battery Condition Meter
The battery condition meter consists of ten lights arranged
in an arc over the on/off key. As the battery voltage drops,
the number of lights reduces from right to left. When the
battery capacity drops to 10% or below, the left red LED
will flash.
! Left Red LED Flashing: Battery charge is low;
Charge the batteries as soon as possible.
! Right-to-Left Ripple of LEDs: FLIGHT is in lock
mode; Unlock the FLIGHT.
! Left-to-Right Ripple of LEDs Alternating with
Steady Display: FLIGHT is in programming, inhibit,
or charging mode.
! Right Green LED Flashing: FLIGHT is in speed limit
mode.
! All LEDs Flashing Slowly: The joystick was not in
the neutral position when the controller was turned
on. If you get “all LEDs flashing slowly,” turn off the
controller, allow the joystick to return to the neutral
position, then turn on the controller.
! All LEDs Flashing Quickly: The FLIGHT has
detected a fault; Refer to the Error Code table.
Figure 30. FLIGHT Controller Keypad
Lock Mode
The Flight controller is equipped with a feature that enables you to “lockout” unauthorized users.
To lock the FLIGHT controller:
1. While the power is on, press and hold the on/off key for 2 seconds. The display will turn off immediately. After 2
seconds, all LEDs will flash briefly and the horn will sound a short beep.
2. The FLIGHT controller is now locked.
To unlock the FLIGHT controller:
1. While the FLIGHT is locked, press the on/off key to turn on the FLIGHT. All LEDs will flash briefly. The LEDs will
then slowly ripple from right to left.
2. Press the horn key twice before the LED ripple has completed, approximately 10 seconds. The FLIGHT is now
unlocked.
36
www.quantumrehab.com
Quantum 610
VII.
OPERATION
Speed Keys
There are two keys that control the speed. Press the hare key to increase the speed. Press the tortoise key to decrease the
speed. The speed setting is displayed on the speed indicator. If your power chair was programmed with a drive profile,
contact your Quantum Rehab Specialist for more information.
NOTE: We recommend that the first few times you operate your power chair, you set the speed to the slowest
setting until you become familiar with your new power chair.
Off-board Charger/Programming Socket
You may use an off-board charger to charge the power chair batteries through the 3-pin socket located on the front of the
FLIGHT. If you use an off-board charger, the charger current should not exceed 8 amps. Contact your Quantum Rehab
Specialist for more information.
WARNING! Only chargers with Neutrik NC3MX plugs should be connected to the off-board charger/
programming socket. See your Quantum Rehab Specialist for more information.
NOTE: The socket may also be used for reprogramming the FLIGHT. Contact your Quantum Rehab Specialist for more information.
Sleep Mode (If Enabled)
The power chair controller features a sleep mode. Sleep mode is a built-in circuit that will automatically shut off the
main power if the joystick is not moved in any direction for a period of time. This time factor is programmed into the
controller. To restore power and continue, push any key on the keypad.
Error Codes
The battery condition meter will flash error codes when the FLIGHT controller detects an abnormal condition in the
electrical system. All of the battery condition meter LEDs will flash a number of times quickly, then pause, then flash
again. The battery condition meter will continue to flash the error codes until the problem is fixed. The table below
identifies the individual error codes. If any of these error codes persist, contact your Quantum Rehab Specialist.
Error Code
Probable Cause
Possible Solution
1
Possible stall timeout or user error
Release the joystick
2
Battery Fault
Check the batteries and cables. Try to charge the
batteries. The batteries may need to be replaced.
3
Left Motor Fault
Check the left motor, connections, and cabling.
4
Right Motor Fault
Check the right motor, connections, and cabling.
5
Left Park Brake Fault
Check the left park brake, connections, and cabling.
6
Right Park Brake Fault
Check the right park brake, connections, and cabling.
7
FLIGHT Controller Module Fault
Check the communications connections and wiring.
8
FLIGHT Power Module Fault
Check the communications connections and wiring.
9
FLIGHT Communications Fault
Check the communications connections and wiring.
10
Unknown Fault
Contact your Quantum Rehab Specialist.
11
Incompatible Controller Fault
Contact your Quantum Rehab Specialist.
Quantum 610
www.quantumrehab.com
37
VII.
OPERATION
VSI ELECTRONIC CONTROLLER
The electronic controller is what you use to operate your power chair. The electronic controller enables you to move the
power chair, as well as monitor battery charge, electronic controller functions, and the condition of your electrical system.
The VSI electronic controller is an integral electronic controller. All of the electronics necessary to operate the power chair
are contained in one module. See figure 31. Typically, the VSI is mounted to one of the armrests and is connected to the
motors, batteries, and the onboard charger (optional) at the power base. The VSI may be used to control some optional
systems such as power elevating leg rests.
The controller supplied with your power chair has been pre-programmed to meet your needs. The program is set using
either a personal computer with software provided by the controller manufacturer or with a hand-held programmer, also
provided by the controller manufacturer.
WARNING! The controller program can affect speed, acceleration, deceleration, and braking. If it
is programmed incorrectly or outside of the safe limits as determined by your healthcare professional, it can create a dangerous situation. Only the power chair manufacturer, an authorized
representative of the manufacturer, or a trained service technician should program the controller.
The VSI consists of:
1. joystick
2. keypad
3. off-board charger/programming socket
4. actuator connector (optional)
5. charger inhibit connector (optional)
6. battery connector
7. motor connector
8. motor connector
Joystick
The joystick controls the direction and speed of your power
chair. When you move the joystick from the neutral (center)
position, the electromagnetic brakes release and allow your
power chair to move. The farther you push the joystick
from its neutral position, the faster your power chair moves.
When you release the joystick and allow it to return to the
neutral position, you engage the electromagnetic brakes.
This causes your power chair to decelerate and come to a
complete stop.
8
Figure 31. VSI Controller (Optional 6-Key Shown)
WARNING! If your power chair begins to move in an unexpected manner, immediately release the
joystick. Unless the joystick is damaged, this action should stop your power chair.
38
www.quantumrehab.com
Quantum 610
VII.
OPERATION
Keypad
The keypad is located in front of the joystick. It contains
keys necessary to operate your power chair. See figure 32.
On/Off Key
The on/off key turns the VSI on and off.
WARNING! Unless faced with an
emergency situation, do not use the
on/off key to stop the power chair.
This will cause the power chair to
stop abruptly.
WARNING! Always turn the power
off when you are stationary to prevent unexpected movement.
Battery Condition Meter
The battery condition meter is a 10-segment illuminated
display located in front of the joystick. It consists of red,
yellow, and green lights. When the lights are on, it indicates
that there is power to the VSI. The lights also indicate
battery status, VSI operational status, and electrical system
status.
! Red, yellow, and green lights lit: Batteries charged;
Figure 32. VSI Controller Keypad
VSI operational, and electrical system OK.
! Red and yellow lights lit: Charge batteries if possible; VSI operational, and electrical system OK.
! Red lights only lit or slow flash: Charge batteries as soon as possible; VSI operational, and electrical system OK.
NOTE: When the batteries approach a discharged state, the first red light will begin to slowly flash, reminding
you the batteries need to be charged immediately!
! Rapid flash of lights: Indicates a fault in the VSI or the electrical system. Refer to “VSI Error Codes.”
! Ripple side to side of lights: The joystick was not in the neutral position when the controller was turned on. If you
get “ripple side to side of lights,” turn off the controller, allow the joystick to return to the neutral position, then turn on
the controller.
NOTE: If you still get “ripple side to side of lights,” contact your Quantum Rehab Specialist.
Speed/Profile Keys
The speed/profile keys control either the speed setting or the drive profile. Press the speed/profile increase key to increase
the speed setting or change the drive profile to a higher number. Press the speed/profile decrease key to decrease the
speed setting or change the drive profile to a lower number. The speed setting or drive profile is displayed on the maximum
speed/profile indicator. If your power chair was programmed with a drive profile, contact your Quantum Rehab Specialist
for more information.
NOTE: We recommend that the first few times you operate your power chair, you use the lowest speed setting
until you become familiar with your new power chair.
Quantum 610
www.quantumrehab.com
39
VII.
OPERATION
Actuator Keys and Actuator Lights (For Optional Equipment)
Actuator keys and actuator lights are used for optional equipment such as power elevating leg rests. For specific operation
of the actuator keys and actuator lights, contact your Quantum Rehab Specialist.
Horn Key
The horn key activates the horn.
Locking/Unlocking the VSI
The VSI has a feature that enables you to lock your power chair to prevent unauthorized use.
To lock the VSI:
1. With the VSI switched on, press and hold the on/off key. After 1 second, the VSI should beep.
2. Release the on/off key.
3. Push the joystick to the full forward position until the VSI beeps.
4. Pull the joystick to the full rearward position until the VSI beeps.
5. Release the joystick. There should be a long beep.
6. The VSI is now locked.
To unlock the VSI:
1. Press the on/off key and power on the VSI. The maximum speed/profile indicator should ripple up and down.
2. Push the joystick to the full forward position until the VSI beeps.
3. Pull the joystick to the full rearward position until the VSI beeps.
4. Release the joystick. There should be a long beep.
5. The VSI is now unlocked.
NOTE: If the above procedure fails to either lock or unlock the VSI, contact your Quantum Rehab Specialist.
Off-board Charger/Programming Socket
The off-board charger/programming socket is located on the front of the VSI. If you use an off-board charger, the charger
current should not exceed 8 amps. Contact your Quantum Rehab Specialist for more information.
WARNING! Only chargers with Neutrik NC3MX plugs should be connected to the off-board charger/
programming socket. See your Quantum Rehab Specialist for more information.
NOTE: The socket may also be used for reprogramming the VSI. Contact your Quantum Rehab Specialist for
more information.
Motor Connectors
This connects the VSI to the power chair’s motors and motor brakes.
Battery Connector
This connects the VSI to the power chair’s batteries.
Actuator Connector (Optional)
This connects the VSI to the power seat actuator.
40
www.quantumrehab.com
Quantum 610
VII.
OPERATION
Charger Inhibit Connector (Optional)
The charger inhibit connector connects the VSI to the onboard battery charger. This connection provides an inhibit that
disables the VSI when the battery charger is on. The charger inhibit connector is coded with colored dots. The dots are
positioned so that you align the flat side of the male connector with the flat side of the female connector before making the
connection.
WARNING! Failure to properly align the connectors can result in damage to the VSI, the charger,
and the connectors.
Thermal Rollback
The VSI controller is equipped with a thermal rollback circuit. This circuit monitors the temperature of the controller, which
roughly translates to motor temperature. In the event that the VSI controller becomes excessively hot (above 140° F), motor
current (amperage) is reduced. For every degree above 140° F, the motor current limit is reduced by .55 amps until the VSI
controller reaches 158° F, at which time the current output is reduced to zero. This reduces your power chair’s “power,”
which could also reduce your power chair’s speed, and allows the electrical components and motors to cool down. When the
temperature returns to a safe level, your power chair resumes its normal operation.
VSI Error Codes
The VSI controller is designed with the user’s safety as the prime consideration. It incorporates many sophisticated selftest features which search for potential problems at a rate of 100 times per second. If the VSI detects a problem either in
its own circuits or in the power chair’s electrical system, it may decide to stop the power chair, depending on the severity
of the problem. The VSI is designed to maximize the user’s safety under all normal conditions. The table below identifies
the individual error codes. Error codes are displayed as a rapid flashing of the battery condition meter lights. If you get one
of these error codes, contact your Quantum Rehab Specialist.
FLASHING LIGHTS
1
DIAGNOSIS AND SOLUTION
The batteries need charging or there is a bad connection to the batteries. Check the
connections to the batteries. If the connections are good, try charging the batteries.
2
The left motor has a bad connection. Check the left motor connection.
3
The left motor has a short circuit to a battery connection. Contact your Quantum Rehab
Specialist.
4
The right motor has a bad connection. Check the right motor connection.
5
The right motor has a short circuit to a battery connection. Contact your Quantum Rehab
Specialist.
6
The power chair is being inhibited by the battery charger. Unplug the battery charger.
7
A joystick fault is indicated. Make sure that the joystick is in the neutral (center) position
before turning on the controller.
8
A controller system fault is indicated. Make sure that all connections are secure.
9
The parking brakes have a bad connection. Check the parking brake and motor
connections. Make sure the controller connections are secure.
10
An excessive voltage has been applied to the controller. This is usually caused by a poor
battery connection. Check the battery connections.
Quantum 610
www.quantumrehab.com
41
VII.
OPERATION
REMOTE PLUS CONTROLLER
The electronic controller is what you use to operate your power chair. The electronic controller enables you to move the
power chair, as well as monitor battery charge, electronic controller functions, and the condition of your electrical system.
The Remote Plus is part of a modular electronic controller system. The system consists of more than one module. Typically,
the Remote Plus is mounted to one of the armrests. See figure 33. It is connected to a power module located on the power
base through the controller communications cable. The Remote Plus may be used to control some optional systems, such
as power elevating leg rests through an actuator/lighting module (ALM) located on the power base.
The controller supplied with your power chair has been pre-programmed to meet your needs. The program is set using
either a personal computer with software provided by the controller manufacturer or with a hand-held programmer, also
provided by the controller manufacturer.
WARNING! The controller program can affect speed, acceleration, deceleration, and braking. If it
is programmed incorrectly or outside of the safe limits as determined by your healthcare professional, it can create a dangerous situation. Only the power chair manufacturer, an authorized representative of the manufacturer, or a trained service technician should program the controller.
Remote Plus
The Remote Plus consists of the following:
1. joystick
2. keypad
3. controller communications cable
4. off-board charger/programming socket
1
Joystick
The joystick controls the direction and speed of your power
chair. When you move the joystick from the neutral (center)
3
position, the electromagnetic brakes release and allow your
power chair to move. The farther you push the joystick from
its neutral position, the faster your power chair moves. When
you release the joystick and allow it to return to the neutral
position, you engage the electromagnetic brakes. This causes
your power chair to decelerate and come to a complete stop. Figure 33. Remote Plus Controller
2
4
WARNING! If your power chair begins to move in an unexpected manner, immediately release the
joystick. Unless the joystick is damaged, this action should stop your power chair.
Keypad
The keypad is located directly in front of the joystick. It contains keys that you will use to control your power chair. See figure 34.
On/Off Key
The on/off key turns the system on and off.
WARNING! Unless faced with an emergency situation, do not use the on/off key to stop the chair.
This will cause the power chair to stop abruptly.
WARNING! Always turn the power off when you are stationary to prevent unexpected movement.
42
www.quantumrehab.com
Quantum 610
VII.
OPERATION
Mode Key (Speed Settings)
The mode key controls the speed settings. The Remote Plus
speed settings range from 1 to 5. Typically, the slowest speed
setting is 1 and the fastest speed setting is 5. The settings
are indicated by the number of lights that are lit on the speed
setting indicator.
NOTE: The speed settings are preset at the factory. If
your Quantum Rehab Specialist changes the order of
these settings, please make note of these changes. Contact your Quantum Rehab Specialist for more information.
To select a speed setting:
1. Press the on/off key to power on the controller.
2. Press the mode key once.
3. To increase chair speed, push the joystick to the right.
Each time you push the joystick, you will increase the
speed setting in the speed setting indicator.
4. To decrease chair speed, push the joystick to the left.
Each time you push the joystick, you decrease the speed
setting in the speed setting indicator.
5. Once you select the desired speed setting, press the
mode key once to keep the setting or push the joystick
in the forward or reverse direction. The chair will resume operation at the selected speed.
Figure 34. Remote Plus Keypad
NOTE: We recommend that the first few times you operate your power chair, you have your speed on the
slowest setting until you become familiar with your new power chair.
Horn Key
The horn key activates the horn.
Battery Condition Meter
The battery condition meter is a 10-segment illuminated display located in front of the joystick. When the lights are on, it
indicates that there is power to the Remote Plus. The lights also indicate battery status, Remote Plus operational status, and
electrical system status.
! Red, yellow, and green lights lit: Batteries charged; controller and electrical system OK.
! Red and yellow lights lit: Charge batteries if possible; controller and electrical system OK.
! Red lights only lit or slow flash: Charge batteries as soon as possible; controller and electrical system OK.
! Rapid flash of lights: Indicates an error in the controller or the electrical system. Refer to “Remote Plus Error Codes.”
! Ripple up and down of lights: The joystick was not in the neutral position when the controller was turned on. If you
get “ripple up and down of lights,” turn off the controller and allow the joystick to return to the neutral position. Then
turn on the controller.
NOTE: If you still get “ripple up and down of lights,” contact your Quantum Rehab Specialist.
Quantum 610
www.quantumrehab.com
43
VII.
OPERATION
NOTE: When the batteries approach a discharged state, the first red light will begin to slowly flash, reminding you the batteries need to be charged immediately!
Right/Left Turn Indicator Keys (Optional)
The right/left turn indicator keys toggle either the left or right turn indicators. Press once to turn on and press again to turn
off. You can also turn off the selected turn indicator by pressing the opposite indicator key or the hazard key.
Light Key (Optional)
The light key turns the headlights/taillights on and off independent of other indicators.
Hazard Key (Optional)
The hazard key activates both turn indicators at the same time. You can only cancel this by pressing the hazard key again.
Power Accessory Indicator (Optional)
Indicates the selected power accessory. This is for optional accessories only.
Power Accessories (Optional)
If your power chair is equipped with power accessories such as power elevating leg rests, you can operate them through
the keypad. Contact your Quantum Rehab Specialist for information on how to operate these accessories.
Off-board Charger/Programming Socket
The off-board charger/programming socket is located on the front of the Remote Plus. If you use an off-board charger, the
charger current should not exceed 8 amps. Contact your Quantum Rehab Specialist for more information.
WARNING! Only chargers with Neutrik NC3MX plugs should be connected to the off-board charger/
programming socket. See your Quantum Rehab Specialist for more information.
NOTE: Changes to the programming can only be made by your Quantum Rehab Specialist.
Controller Communications Cable
The controller communications cable provides the Remote Plus with a connection to the power module.
Sleep Mode
Your Remote Plus controller has a sleep mode feature. Sleep mode is a built-in circuit that automatically shuts off the main
power if the joystick is not moved in any direction for approximately five minutes. The battery condition meter lights on the
keypad indicate sleep mode by blinking once every five seconds. To restore power and continue, push the on/off key
twice.
Thermal Rollback
The Remote Plus is equipped with a thermal rollback circuit. This circuit monitors the temperature of the motors, power
module, and remote. In the event that any of them become excessively hot (above 122° F), motor voltage is reduced. For
every degree above 122° F, the voltage is reduced by 5 volts. This reduces your power chair’s speed and allows the electrical
components to cool down. When the temperature returns to a safe level, your power chair resumes its normal speed.
44
www.quantumrehab.com
Quantum 610
VII.
OPERATION
Remote Plus Error Codes
In addition to indicating the current state of battery charge, the battery condition meter can also indicate possible problems
with your power chair’s electrical system. If any of the battery condition meter lights are flashing rapidly, the controller may
be indicating an error. Error codes are displayed as a number of flashing lights. For instance, if the first light is flashing
rapidly, the battery voltage is nearly depleted. The table below identifies the individual error codes, probable causes, and
possible solutions. If you get one of these error codes, contact your Quantum Rehab Specialist.
FLASHING LIGHTS
1
DIAGNOSIS AND SOLUTION
The batteries need charging or there is a bad connection to the batteries. Check the
connections to the batteries. If the connections are good, try charging the batteries.
2
The left motor has a bad connection. Check the left motor connection.
3
The left motor has a short circuit to a battery connection. Contact your Quantum Rehab
Specialist.
4
The right motor has a bad connection. Check the right motor connection.
5
The right motor has a short circuit to a battery connection. Contact your Quantum Rehab
Specialist.
6
The power chair is being inhibited by the battery charger. Unplug the battery charger.
7
A joystick fault is indicated. Make sure that the joystick is in the neutral (center) position
before turning on the controller.
8
A controller system fault is indicated. Make sure that all connections are secure.
9
The parking brakes have a bad connection. Check the parking brake and motor
connections. Make sure the controller connections are secure.
10
An excessive voltage has been applied to the controller. This is usually caused by a poor
battery connection. Check the battery connections.
Quantum 610
www.quantumrehab.com
45
VII.
OPERATION
THE MICRODRIVE CONTROLLER
The electronic controller is what you use to operate your power chair. It takes the battery voltage and sends it to the
appropriate system. The electronic controller also enables you to monitor battery charge, electronic controller functions,
and the condition of your electrical system. Also, it may be used to control some optional systems such as power elevating
seats and lights. The Microdrive electronic control system is a modular system. The electronics necessary to operate your
power chair are contained in several modules located on different parts of your power chair. Typically, the Microdrive
Controller is mounted to one of the armrests. See figure 35. The other components are located on or inside the power
base.
The controller supplied with your power chair has been pre-programmed to meet your needs. The program is set using
either a personal computer with software provided by the controller manufacturer or with a hand-held programmer, also
provided by the controller manufacturer.
WARNING! The controller program can affect speed, acceleration, deceleration, and braking. If it
is programmed incorrectly or outside of the safe limits as determined by your healthcare
professional, it can create a dangerous situation. Only the power chair manufacturer, an authorized
representative of the manufacturer, or a trained service technician should program the controller.
The Microdrive Controller consists of:
1. joystick
2. display pad
3. mode switch
4. on/off switch
5. speed adjustment dial
6. joystick interface module
7. off-board charger/programming socket
Joystick
The joystick controls the direction and speed of your power
chair. When you move the joystick from the neutral (center)
position, the electromagnetic brakes release and allow the
power chair to move. The farther you push the joystick from
its neutral position, the faster the power chair moves. When
you release the joystick and allow it to return to the neutral
position, the electromagnetic brakes engage and the power
chair comes to a complete stop.
WARNING! If your power chair begins
to move in an unexpected manner,
immediately release the joystick. Unless
the joystick is damaged, this action
should stop your power chair.
Figure 35. Microdrive Controller with Joystick Interface
Module
46
www.quantumrehab.com
Quantum 610
VII.
OPERATION
Display Pad
The display pad is located directly in front of the joystick. It contains the horn key, battery condition meter, profile and speed
indicator, and the actuator indicator. See figure 36.
Horn Key
The horn key activates the horn.
Battery Condition Meter
The battery condition meter is a 10-segment illuminated display that indicates that the Microdrive is powered on and also
gives the status of the batteries, the controller, and the power chair electrical system.
! Red, yellow, and green lights lit: Batteries charged; controller and electrical system OK.
! Red and yellow lights lit: Charge batteries if possible; controller and electrical system OK.
! Red lights only lit or slow flash: Charge batteries as soon as possible; controller and electrical system OK.
! Rapid flash of lights: Indicates a fault in the controller or the electrical system. See “Error Codes.”
! Ripple up and down of lights: The joystick was not in the neutral position when the controller was turned on. If you
get “ripple up and down of lights,” turn off the controller, allow the joystick to return to the neutral position, then turn on
the controller.
NOTE: If you still get “ripple up and down of lights,” contact your Quantum Rehab Specialist.
NOTE: When the batteries approach a discharged state, the first red light will begin to slowly flash, reminding you the
batteries need to be charged immediately!
Profile and Speed Indicator
The profile and speed indicator is a 5-segment illuminated display that indicates speed setting as well as drive
profile.
Actuator Indicator
The actuator indicator is a 4-segment illuminated display that indicates power recline, power tilt, power leg
rest, and power elevating seat actuator modes.
Joystick Interface Module
The joystick interface module provides a means to enable
or disable the horn button, mode switch, on/off switch,
and speed adjustment dial.
NOTE: When a toggle switch is set to “J/S,” the
joystick has control of a particular function. When
the toggle switch is set to “Local,” control of this
function is disabled at the joystick.
Figure 36. Microdrive Display Pad
Quantum 610
www.quantumrehab.com
47
VII.
OPERATION
Drive Profile Selection
Your Microdrive controller may be programmed for more than one drive profile that allows the system to be custom
tailored to your environment.
To select a profile setting:
1. Use the on/off switch to power on the chair and the controller.
2. Press the mode button.
3. Move the joystick left or right to select the desired drive profile. Each of the LEDs indicate a separate profile.
NOTE: The system can be programmed with 5 different profiles.
Speed Adjustment
The Microdrive controller provides a speed control knob to control the speed of the power chair.
To change the speed:
1. Use the on/off switch to power on the chair and the controller.
2. To increase your speed, turn the speed adjustment dial clockwise.
3. To decrease your speed, turn the speed adjustment dial counterclockwise.
Sleep Mode
The Microdrive controller offers a sleep mode feature which will shut off the main power if the joystick remains stationary
for a period of five minutes. The battery condition meter will indicate sleep mode by blinking once every five seconds. To
restore power and resume operation of the chair, flip the on/off switch twice.
Thermal Rollback
The Microdrive controller is equipped with a thermal rollback circuit which monitors the temperature of the chair’s motors
and controller. If either exceeds 122° F, the controller reduces the motor voltage by 5 volts for every degree over. This
reduces the chair’s speed and allows a cool down period. Once the temperature returns to a safe level, the chair will
resume normal operation.
Error Codes
In addition to indicating the current state of battery charge, the battery condition meter can also indicate possible problems
with your power chair’s electrical system. If any of the battery condition meter lights are flashing rapidly, the controller may be
indicating an error. Error codes are displayed as a number of flashing lights. For instance, if the first light is flashing rapidly, the
battery voltage is nearly depleted. The following table identifies the individual error codes, probable causes, and possible
solutions. If you get one of these error codes, contact your Quantum Rehab Specialist.
48
www.quantumrehab.com
Quantum 610
VII.
FLASHING LIGHTS
10
OPERATION
DIAGNOSIS
High Battery Voltage
SOLUTION
Check batteries.
9
Solenoid Brake Fault
Check motor/brake wiring.
8
Possible Controller Fault
See Quantum Rehab Specialist.
7
Possible Joystick Fault
See Quantum Rehab Specialist.
6
Inhibit Active
Unplug charger. Check connections.
5
Right Motor Wiring Fault
Check right motor wiring.
4
Right Motor Disconnected
Check right motor wiring.
3
Left Motor Wiring Fault
Check left motor wiring.
2
Left Motor Disconnected
Check left motor wiring.
1
Low Battery Voltage
Check batteries/battery wiring.
Quantum 610
www.quantumrehab.com
49
VIII.
CARE
AND
MAINTENANCE
CARE AND MAINTENANCE
Your Quantum 610 is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance checks. You
can perform some of these checks, but others require assistance from your Quantum Rehab Specialist. Preventive maintenance is very important. If you follow the maintenance checks in this section as scheduled, you can help ensure that your
power chair gives you years of trouble-free operation. If you have any doubt as to your power chair’s care or operation,
contact your Quantum Rehab Specialist.
WARNING! Prevent injury. Do not service the power chair when the seat is occupied.
Your power chair, like most electrical equipment, is susceptible to damage from the elements. Avoid damp areas of
any kind.
WARNING! Direct exposure to water or dampness could cause the power chair to malfunction
electronically and mechanically. Water can cause electrical components to corrode and the chair’s
frame to rust.
Should your power chair come in contact with water:
1. Dry your power chair as thoroughly as possible with a towel.
2. Allow your power chair to sit in a warm, dry place for 12 hours to allow unseen water to evaporate.
3. Check the joystick operation and the brakes before using your power chair again.
4. If any inconsistencies are found, take your power chair to your Quantum Rehab Specialist.
Temperature
! Some of the parts of your power chair are susceptible to extreme changes in temperature.Always keep your power chair between
the temperatures of 18° F and 122° F.
! In extremely cold temperatures the batteries may freeze. The specific temperature at which they freeze depends on a number of
factors, such as battery charge, usage, and composition of the batteries (e.g., AGM or Gel-Cell).
! Temperatures above 122° F may cause your power chair to operate at a reduced speed. This reduced speed is a safety feature built
into the controller that helps prevent damage to the motor and other electrical components. See VII. “Operation.”
General Guidelines
! Avoid knocking or bumping the controller, especially the joystick.
! Avoid prolonged exposure of your power chair to extreme conditions, such as heat, cold, or moisture.
! Keep the controller clean.
! Check all connectors to ensure that they are all tight and secured properly.
! Make sure pneumatic drive tires are inflated to 35 psi (2.4 bar).
WARNING! Overinflating tires can cause them to explode and can result in personal injury.
WARNING! Do not use a high pressure hose to inflate your tires.
! Use a rubber conditioner on the tire sidewalls to help preserve them.
WARNING! Never use a rubber conditioner on the tread area of the tires; doing so may make the
tires slippery and cause your power chair to skid.
50
www.quantumrehab.com
Quantum 610
VIII.
CARE
AND
MAINTENANCE
! The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help it retain
its high-gloss appearance.
! Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within the battery
tray, with the battery terminals facing inward, toward each other. Refer to the battery wiring label for the correct wiring
layout.
! All wheel bearings are prelubricated and sealed. They require no subsequent lubrication.
Daily Checks
! With the controller turned off, check the joystick. Make sure it is not bent or damaged and that it returns to the neutral
position when you release it. Check the rubber boot around the base of the joystick for damage. Visually inspect the
boot. Do not handle or try to repair it. See your Quantum Rehab Specialist if there is a problem.
! Visually inspect the controller cable. Make sure that it is not frayed, cut, or has any wires exposed. See your Quantum
Rehab Specialist if there is a problem.
! Check for flat spots on solid tires. Flat spots could adversely affect stability.
Weekly Checks
! Disconnect and inspect the controller from the power base. Look for corrosion. Contact your Quantum Rehab Specialist if
necessary.
! Ensure that all parts of the controller system are securely fastened to your power chair. Do not overtighten any screws.
! Check for proper tire inflation. There should be 35 psi (2.4 bar) in each tire. If a tire does not hold air, see a Quantum Rehab
Specialist for replacement of the tube.
! Calibrate the joystick if a noticeable difference in performance is detected or if the joystick does not operate properly. To calibrate
the joystick, power off the unit, place the joystick in the neutral position, and power the unit back on. If a problem still exists with your
joystick’s performance, contact your Quantum Rehab Specialist.
! Check the brakes. This test should be carried out on a level surface with at least three feet of clearance around your power chair.
To check the brakes:
1. Turn on the controller and turn down the speed level of your power chair.
2. After one second, check the battery condition meter. Make sure that it remains on.
3. Slowly push the joystick forward until you hear the electric brakes click. Immediately release the joystick. You must be
able to hear each electrical brake operating within a few seconds of joystick movement. Repeat this test three times,
pushing the joystick backwards, then left, and then right.
Monthly Checks
! Check for drive tire wear. See your Quantum Rehab Specialist for repair.
! Check the caster wheels for wear. Replace them as necessary.
! Check the caster forks for damage or fluttering which indicates that they may need to be adjusted or have the bearings
replaced. See your Quantum Rehab Specialist for repair.
! Keep your power chair clean and free of foreign material, such as mud, dirt, hair, food, drink, etc.
Yearly Checks
Take your power chair to your Quantum Rehab Specialist for yearly maintenance. This helps ensure that your power chair
is functioning properly and helps prevent future complications.
Quantum 610
www.quantumrehab.com
51
VIII.
CARE
AND
MAINTENANCE
Storage
Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries
from the power chair. See VI. “Batteries and Charging.”
WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be
damaged.
Cleaning Instructions
WARNING! Never hose off your power chair or place it in direct contact with water. Your power chair
has a painted, ABS plastic body shroud that allows it to be easily wiped clean with a damp cloth.
WARNING! Never use any chemicals to clean a vinyl seat, as they may cause the seat to become
slippery or dry out and crack. Use soapy water and dry the seat thoroughly.
Wheel Replacement
If you have pneumatic tires and you have a flat tire, you can replace the tube. If your chair is equipped with a solid tire
insert, then you must replace the entire wheel assembly. Replacement tires, tubes, and wheel assemblies are readily available through your Quantum Rehab Specialist.
WARNING! To avoid possible injury, be sure that the controller’s power is turned off and the
power chair is not in freewheel mode before performing this procedure.
WARNING! Completely deflate the tire before attempting repair.
TIRE
AXLE KEY
REAR RIM HALF
TUBE
WHEEL
HUB
AXLE
SLOT
FRONT RIM
HALF
NUTS
DRIVE DRIVE
WHEEL WHEEL
NUT
WASHER
WASHERS
Figure 37. Quantum 610 Drive Wheel
Figure 38. Quantum 610 Drive Wheel Disassembled
Follow these easy steps for a quick and safe repair for both pneumatic and solid tires:
1. Turn off the power to the controller.
2. Set the power chair up on blocks.
3. If you are changing a pneumatic tire, completely deflate it before removing the wheel.
4. Remove the drive wheel nut and washer from the axle. See figure 37.
5. Pull the wheel off the axle.
6. Remove the nuts and washers from the wheel hub and separate the rim halves. See figure 38.
7. Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if it is a solid tire.
52
www.quantumrehab.com
Quantum 610
VIII.
8.
9.
10.
11.
12.
CARE
AND
MAINTENANCE
Reassemble the rim halves and reinstall the nuts and washers to the wheel hub.
Slide the wheel back onto the axle. Make sure that the key is in the axle slot.
Reinstall the drive wheel nut and washer to the axle and tighten.
Inflate the pneumatic tire to 35 psi (2.4 bar).
Remove the power chair from the blocks.
Battery Replacement
A battery wiring diagram is printed on a decal located on the front battery tray. See VI. “Batteries and Charging” for
correct battery specifications.
WARNING! Prevent injury. Do not replace the batteries when the seat is occupied.
WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds.
Wear goggles and gloves when handling batteries and wash hands after handling.
WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that
much weight, be sure to get help. Lifting beyond your capacity can result in personal injury.
WARNING! Prevent injury and/or equipment damage! Do not mix or match new and old batteries.
If you encounter a situation where one battery needs to be replaced, then replace both batteries.
Refer to the specifications table in this manual and the manual suppled with the battery charger
for recommended type and capacities.
To replace the batteries:
1. Turn off the power to the controller.
2. Make sure that the power chair is in drive mode. See III. “Your Power Chair.”
3. Loosen the rear shroud fasteners.
4. Remove the rear shroud. See figure 39.
5. Disconnect the battery harness from the rear battery.
6. Remove the retaining pin and lift off the front cover using the foot platform bracket. See figure 19.
7. Slide the battery tray forward.
8. Disconnect the battery harness from the front battery.
9. Unfasten the hook and loop straps from both batteries.
10. Remove the batteries.
11. Install new batteries.
12. Fasten the hook and loop straps around both batteries.
13. Connect the battery harness to the front battery according to the battery wiring diagram. See figure 39.
WARNING! Prevent injury. Make sure you tighten the fasteners so that the connections are secure.
14. Slide the battery tray back into the power base.
15. Connect the battery harness to the rear battery.
16. Reinstall the front cover.
17. Reinstall the rear shroud and tighten the fasteners.
18. Charge the batteries. See VI. “Batteries and Charging.”
Quantum 610
www.quantumrehab.com
53
VIII.
CARE
AND
MAINTENANCE
REAR SHROUD FASTENERS
REAR SHROUD
BATTERY WIRING DIAGRAM LABEL
FRONT BATTERY
REAR BATTERY
Figure 39. Battery Installation
54
www.quantumrehab.com
Quantum 610
VIII.
CARE
AND
MAINTENANCE
When to See Your Quantum Rehab Specialist for Service
The following symptoms could indicate a serious problem with your power chair. If necessary, contact your Quantum
Rehab Specialist. When calling, have the model number, serial number, nature of the problem, and the error code if
available.
! Motor noise
! Frayed harnesses
! Cracked or broken connectors
! Uneven wear on any of the tires
! Jerky motion
! Pulling to one side
! Bent or broken wheel assemblies
! Does not power up
! Powers up, but does not move
Corrective Maintenance
If the battery condition meter does not light up when you turn on the power:
! Check the harness connections. Make sure they are tight.
! Check the circuit breaker. Reset it if necessary.
! Check the battery connections.
If the above conditions prove normal, you can load test the batteries with a battery load tester. These testers are available
at automotive parts stores. Disconnect both batteries before load testing and follow the directions that come with the load
tester. If either one of the batteries fails the load test, replace both of them. If your power chair still does not power up,
contact your Quantum Rehab Specialist.
Quantum 610
www.quantumrehab.com
55
IX.
WARRANTY
LIFETIME LIMITED WARRANTY
For the lifetime of your power chair from the date of purchase, Pride will repair or replace at our option to the original
purchaser, free of charge, any of the following parts found upon examination by an authorized representative of Pride to be
defective in material and/or workmanship:
Structural frame components, including:
! Main Frame
! Fixed-position seat post
TWO-YEAR LIMITED WARRANTY
For two (2) years from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
Electronic components, including:
! Charger Assembly
! Controller
! Joystick
Other components, including:
! Foot riggings
Main frame assemblies, including:
! Anti-tip forks
! Caster forks
! Caster beam
! Metal seat framing
! Electrical Harness
! Foot rigging mounting brackets
18-MONTH LIMITED WARRANTY
For eighteen (18) months from the date of purchase, Pride will repair or replace at our option to the original purchaser, free
of charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
! Motor/gearbox assembly
! Power seat actuator
ONE-YEAR LIMITED WARRANTY
For one (1) year from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
! Accessories
! Brakes (electronic function ONLY)
SIX-MONTH LIMITED WARRANTY
For six (6) months from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
! Bearings and bushings
! Plastic components, except body
The battery is covered by a separate six-month warranty, provided by the battery manufacturer. The batteries are not
warranted by Pride.
56
www.quantumrehab.com
Quantum 610
IX.
WARRANTY
RECONDITIONED UNITS WARRANTY
All reconditioned units are covered by a six-month warranty from Pride effective from the date of purchase.
WARRANTY EXCLUSIONS
This warranty does not extend to those items which may require replacement due to normal wear and tear.
! ABS Plastic shrouds
! Motor brushes
! Upholstery and seating
! Brake Pads
! Tires and tubes
! Fuses/Bulbs
! Circumstances beyond the control of Pride
! Labor, service calls, shipping, and other charges incurred for repair of the product, unless specifically authorized, IN
ADVANCE, by Pride Mobility Products Corporation
! Repairs and/or modifications made to any part without specific consent from Pride
Exclusions also include components with damage caused by:
! Contamination
! Abuse, misuse, accident, or negligence
! Battery fluid spillage or leakage
! Commercial use, or use other than normal
! Improper operation, maintenance, or storage
NOTE: Gradual deterioration in performance because the battery has been left in a discharged state, left in
cold conditions for an extended period of time, or worn out through heavy use is not covered.
SERVICE CHECKS AND WARRANTY SERVICE
Warranty service must be performed by a Quantum Rehab Specialist. Do not return faulty parts to Pride without prior
written authorization. All transportation costs and shipping damage incurred while submitting parts for repair or replacement
are the responsibility of the purchaser.
Failure to follow the instructions, warnings, and notes in the owner’s manual and those located on your Pride product can
result in personal injury or product damage and will void Pride’s product warranty.
There is no other express warranty.
IMPLIED WARRANTIES
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1) year from
the date of purchase and to the extent permitted by law. Any and all implied warranties are excluded. This is the exclusive
remedy. Liabilities for consequential damages under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion of limitation
incidental or consequential damages. The above limitation or exclusion may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary from state to state.
Please fill out and return the product registration card to Pride. This will aid Pride in providing the best possible technical
and customer service.
Quantum 610
www.quantumrehab.com
57
NOTES
58
www.quantumrehab.com
Quantum 610
Thank you for
making the
Quantum 610 your
choice in power
chairs.
Quality Control - Quantum 610
Inclusion of all Parts
Fit and Finish
Joystick Serial Number
Performance
Controller Serial Number
Left Motor Serial Number
Right Motor Serial Number
We have
thoroughly
inspected your
Quantum 610. The
following check
marks indicate
that it has been
tested, driven, and
inspected.
#
In Q 1
uali
ty
Pride keeps a more detailed report on file at the factory.
Date Inspected
Inspector
*infmanu2924*
Serial #