Sharp PN-L802B Operating instructions

LCD MONITOR
TOUCH PANEL DRIVER
OPERATION MANUAL
Applicable models
PN-L802B/PN-L702B/PN-L602B
for Mac
Version 1.0
Contents
Introduction.......................................................................3
System Requirements...................................................3
Setting up the Computer..................................................4
Installing the touch panel driver....................................4
Touch Panel Settings........................................................5
How to configure settings..............................................5
Calibration.....................................................................6
Properties......................................................................7
Uninstalling the Driver Software.....................................9
Touch Action...................................................................10
Important Information
•This software has been shipped after strict quality control and product inspection. If, however, you find any failure or
malfunction, contact your product dealer.
•Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a
third party, nor for any other malfunctions or damage to this software arising during use, except where indemnity liability is
recognized under law.
•Transcribing or duplicating part or all of this manual and/or this software without permission from our company is not
permitted.
•As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
•The contents or details may vary depending on the screen configuration and OS version, etc.
•Only an English version of the touch panel driver is provided. The screens shown in the manual are the screens that appear
in the English OS.
•This manual does not contain basic operating instructions for Mac OS.
Trademarks
•Apple, Mac and Mac OS are registered trademarks of Apple Inc.
•Intel is a trademark or registered trademark of Intel Corporation or its subsidiaries in the U.S.A. and other countries.
• All other brand and product names are trademarks or registered trademarks of their respective holders.
E
2
Introduction
System Requirements
To use the touch panel, the touch panel must be connected to a computer, and the touch panel driver must be installed on the
computer.
OS
Mac OS X v10.6, Mac OS X v10.7
CPU
Intel processor
Memory
At least 2 GB
Free space on hard drive
At least 5 MB
TIPS
• Depending on the application software, touch operation may not be possible (for example, if the application processes mouse
and other operations independently).
3
E
Setting up the Computer
To use the touch panel, the touch panel driver must be installed and the touch panel must be connected to your computer.
Installing the touch panel driver
The touch panel driver is a program that enables you to use the touch panel to operate the computer that is connected to the
touch panel.
Caution
• To install, an administrator name (user name) and password are required.
• If an older version of the touch panel driver is installed, remove (uninstall) the old version before installing the touch panel
driver. (See page 9.)
• If you are using a USB hub, use a self-powered hub (a hub capable of supplying a 500 mA current). The touch panel will not
operate correctly if a bus-powered USB hub is used.
• Do not touch the touch panel when connecting the USB cable.
If you touch the touch panel, it will lead to a malfunction. In this case, disconnect and then reconnect the USB cable.
1. Start your computer.
2. Exit all applications that are running.
3. Connect the USB cable for the touch panel to the computer.
To the USB terminal
of the computer
USB port
USB cable (Supplied)
PN-L802B
USB port
4. Run the setup program.
(1) Double-click the “TouchPanelDriver” folder.
(2) Double-click “Sharp TouchPanal.mpkg”.
5. Click “Continue”.
Follow the on-screen instructions to install the driver.
• If a screen prompting you to enter the name and password appears, enter the name and password of the administrator
and click “Install Software” (or “OK”).
• If the “When this software finishes installing, you must restart your computer. Are you sure you want to install the software
now?” screen appears, click “Continue Installation”.
6. When the installation finished screen appears, click “Restart”.
This completes the installation of the touch panel driver.
Each time the computer is started, the touch panel driver will start automatically to enable the touch panel to be used.
The first time you use the touch panel, perform calibration (position adjustment). (See page 6.)
E
4
Touch Panel Settings
The touch panel driver starts automatically and the icon (
) appears on the menu bar.
Caution
• When using the touch panel, set the “SIZE” of the monitor to “WIDE”, “NORMAL”, or “Dot by Dot”.
The touch panel cannot be used when the “SIZE” is set to “ZOOM1” or “ZOOM2”.
How to configure settings
nConfiguring settings from the menu bar
1. Click the touch panel driver icon (
2. Click a menu to change a setting.
) on the menu bar.
•
•
•
•
Current Screen Resolution: The current screen resolution appears.
Calibration: See page 6.
Properties: See page 7.
Hardware Information: Select this to specify “Rotate Mode”, “Test Information”, and “Service Mode”.
-Rotate Mode:
Select the angle of rotation when the screen is rotated on a monitor that can be installed in a vertical orientation.
-Test Information/Service Mode:
Select to view operating conditions. (For service technicians.)
• Version Information: Shows the version of the touch panel driver.
• Disable TP Driver:
Select to disable the touch panel function.
To disable a single touch panel function, see “Function Setting” (page 8).
nConfiguring settings from System Preferences
1. Click “System Preferences” from the Apple menu (
2. Click “SharpTouchPanel”.
3. Click the menu and select settings.
).
Menu
TIPS
• If the “Show Setting Utility in menu bar” checkmark is removed, the touch panel driver icon (
menu bar.
) does not appear on the
5
E
Touch Panel Settings
Calibration
Calibration is used to perform position alignment so that the mouse cursor moves to the correct position when the screen is
touched.
Caution
• When setting the “Simple” on PN-L802B, change the screen size to “Wide” and set the “Advanced” beforehand. When the
screen size is “NORMAL” or “Dot by Dot” and the “Advanced” is set before the “Simple”, the mouse cursor may be out of
position.
nCalibration Method
Simple
This function can be used if the screen resolution is set to “1920 x 1080”, “1360 x 768” or “1280 x 720”.
If using a non-supported resolution, perform advanced calibration.
Select the currently displayed screen size (“WIDE”, “NORMAL”, “Dot by Dot”), and calibration takes place automatically.
Calibrate using advanced calibration if the mouse cursor is out of position when the touch pen is used.
TIPS
• When a key has been assigned to the “Easy Change” hot key setting, the key can be pressed to successively change a
setting.
Advanced
Calibration can be performed manually. Click “Start” to open the settings. Follow the on-screen instructions. (To cancel during
calibration, press the [esc] key on the keyboard.)
When using the PN-L802B, if the position shifts with “4 Points”, adjust using “25 Points”. When adjusting at “25 Points”, use the
touch pen. It may not be possible to correctly adjust with your finger.
nHot Key Setting
Hot keys can be set to perform the operations below. The [Control] and [Shift] keys are fixed as hot keys. One of the A to Z or 0
to 9 keys can be selected for the third hot key.
Easy Change : The calibration method can be changed to “Simple” by pressing the hot key. Settings can be successively
changed by pressing the hot key.
Calibration
: The hot key can be pressed to open the Select Calibration screen.
E
6
Touch Panel Settings
Properties
Settings for the touch action and the touch pen can be configured in the properties.
nDouble Click Range
Set how much the position can shift between the first touch and the second touch and still be recognized as a double-click. To
return the setting to the default setting, click “Default”.
nDouble Click Speed
Set the time that is recognized as a double-click. When a second touch occurs within the set time after the first touch, it is
recognized as a double-click.
Speed Setting (Auto)
The inside of the frame can be touched twice (double-clicked) to set the speed automatically based on the interval between the
touches.
Set Manually
The speed can be set manually from “Slow” (about 1 second) to “Fast” (about 0.3 seconds).
Test
When the inside of the frame is double-clicked by touching it twice, the screen changes. If the screen does not change, repeat
the setting.
Default
Click to restore the default setting.
TIPS
• Depending on the application software, changing the setting may not have any effect (for example, if the setting is set
separately in the application).
7
E
Touch Panel Settings
nOperation Settings
Function Button 1 (Black)
Set the function that activates when function button 1 is pressed with the touch pen.
• RightClick : Functions as a right click.
• Disable : Disables function button 1.
Input Mode Setting
Set the input mode for the touch panel. It is normally recommended that you use “Standard”.
• Standard :Automatically switches between pen mode and handwriting mode.
• HandWrite :Select this when you only wish to use your finger and will not be using the touch pen function.
• Pen
:Select this for operation by touch pen only. Only the touch pen can be used; your finger cannot be used.
Resolution Change Notice
• Enable : When the screen resolution is changed, a message is displayed regarding the calibration setting.
• Disable : When the screen resolution is changed, the previously set calibration values are automatically applied. When a
resolution is used for the first time, the message regarding the calibration setting will appear.
TIPS
• Notification may be delayed, depending on the state of the computer.
nFunction Settings
Select the Gesture Operation to be used.
E
8
Uninstalling the Driver Software
Caution
• To uninstall, an administrator name (user name) and password are required.
1. Disconnect the USB cable.
2. Execute uninstall.
(1) Double-click the “TouchPanelDriver” folder.
(2) Double-click “TouchPanelDriver Uninstaller.app”.
(3) Click “Uninstall”.
•If a screen prompting you to enter the name and password appears, enter the name and password of the administrator
and click “OK”.
3. When the uninstall finished screen appears, click “Quit”.
This completes the uninstallation.
9
E
Touch Action
When the touch panel is touched with the pen, the input mode
changes to pen mode. When touched with your finger, the
input mode changes to handwriting mode. The input mode is
set by default to change automatically (Standard mode).
TIPS
• Also read the manual for the monitor.
• Select the action to be used in Function Setting. (See page
8.)
nCommon finger and pen actions
Tap
Same action as left-clicking a mouse.
Touch with your finger/pen.
nFinger actions
TIPS
• Touch with two fingers, and after about 1 second, move
your fingers. The response may not be correct if you move
your fingers immediately after touching.
• The screen may not respond correctly in the following
cases:
Touching is too quick
The distance between the two points is too short
The two points intersect
• Operation with the touch pen is not possible.
Two Finger Scroll
Use in screens that can be scrolled.
With your two fingers touching the screen, move in the
direction you want to scroll. The screen scrolls in the direction
of the movement.
Double-tap
Same action as double-clicking a mouse.
Quickly touch twice with your finger/pen.
Two Finger Rotation
Use this action in a screen that is capable of image rotation.
Touch the screen with two fingers and rotate to rotate the
screen in that direction.
Rotate two fingers in the
same direction.
When double-tapping with your finger, be sure to lift your
finger sufficiently off the screen after the first tap. If there
is insufficient distance between the screen and your finger,
double-tap will not take place.
Drag-and-drop
Same action as drag-and-drop with a mouse.
Touch the screen with your finger/pen and move without lifting.
When you have finished the movement, lift your finger/pen.
E
10
Touch Action
Two Finger Pinch
Use in a screen that is capable of reduction/enlargement.
Touch the screen with two fingers and move your fingers
closer together to reduce the view, or apart to enlarge the
view.
nPen actions
Function Button 2
Pen tip
Ultrasonic transmitter
Battery indicator
Function Button 1
Function Button 1
Pressing Function Button 1 has the same action as
rightclicking a mouse.
The battery indicator illuminates.
Reduction
Function Button 2
This button is not used for Mac.
The battery indicator illuminates.
TIPS
• Use Function Button near the front of the screen. If too far
away, operation will not be possible.
• Press Function Button slowly and firmly. If pressed too
quickly, the action will not be recognized.
• If the pen tip becomes worn or damaged, replace it. Pull
out the old pen tip and insert a new pen tip.
Enlargement
11
E
PN-L802BL702BL602B DM EN12C(1)