Samsung SOC-4120AP Instruction manual

LENS BUILT IN
WDR COLOR CCD CAMERA
INSTRUCTION MANUAL
SOC-4120AN/P
About this manual
Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.
SALES NETWORK
•
SAMSUNG TECHWIN CO., LTD.
Optics & Digital Imaging Division 145-3, Sangdaewon 1-Dong,
Jungwon-Gu, Sungnam, Kyungki-Do, Korea 462-703
TEL : 82-31-740-8137~41 FAX: 82-31-740-8145
•
SAMSUNG OPTO-ELECTRONICS AMERICA, INC. (SOA)
Closed Circuit Division 40 Seaview Drive, Secaucus N.J 07094,
U.S.A
TEL : (201) 902-0347 FAX: (201) 902-0429
•
SAMSUNG OPTO-ELECTRONICS UK LTD (SOUK)
Samsung House, 1000 Hillswood Drive Hillswood Business
Park Chertsey Surrey KT16 OPS
TEL : 44-(0)1932-45-5308 FAX: 44-(0)1932-45-5325
•
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD (TSOE)
7 Pingchang Rd, Nankai Dist, Tianjin, P.R China
Post Code : 300190
TEL : 86-22-2761-9698 FAX: 86-22-2761-6514
www.samsungtechwin.com
www.samsungcctv.com
P/No. : Z6806-0474-01A
VAN 04. 2
SAMSUNG CCD CAMERA
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
WARNING - Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
Features
Warning
Wide Dynamic Range(WDR)
Auto Iris Vari-Focal Lens Built In
SV-II DSP chip built-in SAMSUNG TECHWIN
allows the camera to find the best picture
conditions in any environment and
automatically gives a necessary light level
compensation, so you can always obtain
the clear picture, the finest detail and
perfect light contrast.
The focal length of lens is 3.8 to 9.5
mm, equivalent to 2.5x zoom.
The built-in lens allows the camera to
have a Wider Dynamic Range, therefore
you can use in various applications.
The camera needs periodic inspection.
Contact an authorized technician for inspection.
Wide Range ATW
The White Balance can be automatically
adjusted in response to light condition
so that you can observe in an appropriate
color balance.
Fine Picture Condition Under Very
Low Illumination (SENSE UP)
Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a long time, a
fire may be caused.
Do not Install the camera on a surface that can not support it.
Unless the surface is suitable, it could cause falling or other hazards.
1/3 high density CCD and digital
processor permit high quality pictures to
be captured in very low light condition.
Adoptable
One power connection self-configures
to either 12V DC or 24V AC.
AC line lock standards with all cameras
in 24V AC operation.
High Resolution
SSNR(Samsung Super Noise
Reduction) CHIP
The horizontal resolution of 500TV lines
can be achieved by using a high density
CCD having Double Speed 410,000 pixels
SONY CCD, which provides clean,
noiseless and reliable pictures.
SOC-4120AN/P has an assistant DSP chip
that can remove image noise efficiently
and it shows clean and obvious image in
low luminance
Do not hold plug with wet hands.
It could cause an electric shock.
Do not disassemble the camera.
It may result in fire, electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
MOTION DETECTION
Electronic DAY/NIGHT
The camera transmits an alert signal to
the REMOTE jack when it detects motion
of an object. If you connect an optional
alarm to the camera, you can get the
effective surveillance.
COLOR CCD CAMERA
It may result in fire or other hazards.
In normal or high luminance, camera
maintains color mode. On the contrary, it
get changed into B/W mode in low
luminance.
4
User’s Manual
COLOR CCD CAMERA
5
User’s Manual
Contents
Precautions
8
Composition
10
Name and Function of Each Part
11
Front
Bottom
Back
11
12
13
Connection
14
Connecting to Monitor
Connecting to Power
14
15
16
Operating Your Camera
Configuration of The Menu
COLOR CCD CAMERA
16
6
User’s Manual
Setting Up The Menu
• CAMERA ID
• BACKLIGHT
• WHITE BALANCE
• MOTION DETECTION
• IRIS LEVEL CONTROL
• SHUTTER SPEED CONTROL
• SENSE UP
• GAIN
• SSNR
• SPECIAL
17
18
21
22
23
26
27
28
29
30
31
Using Remote Jack / MD Output
33
Troubleshooting
34
Specifications
36
COLOR CCD CAMERA
7
User’s Manual
Precautions
Do not install the camera in
extreme temperature conditions.
Do not install or use the camera in an
environment where the humidity is high.
Only use the camera under conditions
where temperatures are between -10 C
and +50 C. Be especially careful to provide
ventilation when operating under high
temperatures.
It can cause the image quality to be poor.
Do not install the camera under
unstable lighting conditions.
Do not drop the camera or subject
them to physical shocks.
It can cause malfunctions to occur.
Never keep the camera face to
strong light directly.
It can damage the CCD.
Do not expose the camera to rain
or spill beverage on it.
Do not touch the front lens of the
camera.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that corrode
the electronic components.
Notes
Severe lighting change or flicker can
cause the camera to work improperly.
COLOR CCD CAMERA
8
It is one of the most important parts of
the camera. Be careful not to be stained
by fingerprint.
User’s Manual
• If the camera is exposed to spotlight or object reflecting strong light, smear or
blooming may occur.
• Please check that the power satisfies the normal specification before connecting
the camera.
COLOR CCD CAMERA
9
User’s Manual
Composition
Name and Function of Each Section
Front
1. WDR Color CCD Camera
SOC-4120AN/P
2. Remote Plug
Tripod Mounting Bracket Screw Hole
Used to fix the Tripod mounting bracket on the
top of the camera.
Control Cover
Used to access focus or zoom handle
Zoom Handle
To adjust zoom maginification by turning.
Focus Handle
To provide for accurate focusing of an
object within the lens field of view.
3. Instruction Manual
Notes
• When you finish adjusting zoom and focus lever, fix the lever by turning clockwise.
COLOR CCD CAMERA
10 User’s Manual
COLOR CCD CAMERA
11 User’s Manual
Name and Function of Each Section
Back
Bottom
Power LED
The LED turns on
when power is supplied.
Tripod Mounting Hole
Used to install the camera on an optional
tripod. The tripod must be equipped with
the screw specified as shown below.
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
Video Output Jack
Used to connect an external
video monitor in jack.
L
Remote Jack
Used to connect a
remote plug.
Tripod Mounting Bracket
Frame Ground
MD Output Terminal
Used to output motion
detection signal.
AC / DC Power Terminal
Used to connect an AC 24V or DC 12V power source.
You can remove and install this bracket on the top
of the camera. You must use the supplied screw
or the equivalent (within 6mm). If not, the bracket
may not be fixed properly.
COLOR CCD CAMERA
12 User’s Manual
Menu Setup Buttons
• SET Button: Used to access menu mode. Also used to confirm the setting.
• UP/DOWN Button: Used to choose the desired menu item. It also moves
the cursor up or down in the menu screen.
• LEFT/RIGHT Button: Used to change the parameter of the selected menu item.
It also moves the cursor the left or right in the menu screen.
COLOR CCD CAMERA
13 User’s Manual
Connection
Connecting to Monitor
Connecting to Power
Connect the VIDEO Out jack to the monitor VIDEO In jack.
CCD Camera
Monitor
• Use AC 24V/300mA or DC 12V/500mA power source for SOC-4120N/P.
• As the connecting method varies with the instruments, refer to the manual
supplied with the instrument.
• If necessary, you can connect the monitor to the REMOTE jack on the back
of your camera. For details, see page 33.
• Only connect the cable when the power is turned off.
• Set the 75Ω/Hi-Z selection switch as shown below if you have an intermediate device.
CCD Camera
Intermediate
End monitor
Resistance of copper wire [at 20C˚ (68˚F)]
#24(0.22mm2)
#22(0.33mm2)
#20(0.52mm2)
#18(0.83mm2)
Resistance (Ω / m)
0.078
0.050
0.030
0.018
Voltage Drop (V/m)
0.028
0.018
0.011
0.006
Copper wire size (AWG)
• As the voltage drop according to the length of the cable in the above table, a
camera may malfunction if there is an excessively long cable run.
* Voltage for camera operation: 12V DC ±10%
* Voltage drops in the above table are variable according to types of cable manufacturer.
Notes
• Be sure to connect power only after all the installation is complete.
• Note that AC or DC adaptor is not supplied with camera.
• Use the UL listed, class 2 power transformer of AC 24V adaptor.
• Ground should be connected to the GND terminal.
COLOR CCD CAMERA
14 User’s Manual
COLOR CCD CAMERA
15 User’s Manual
Operating Your Camera
Configuration of The Menu
SETUP MENU
Setting Up The Menu
Use the five SETUP MENU buttons on back of the camera.
CAMERA ID (see page 18)
• OFF • ON
BACKLIGHT (see page 21)
• WDR • BLC • OFF
WHITE BAL. (see page 22)
• W-ATW • S-ATW • AWC
UP button
LEFT button
SET button
• MANUAL
MOTION DET. (see page 23)
• OFF • MD1 • MD2
IRIS LEVEL CONTROL (see page 26)
• LEVEL
SHUTTER (see page 27)
• OFF • 1/100 (1/120) • MANUAL
SENSE UP (see page 28)
• Auto • OFF
GAIN (see page 29)
• OFF • AGC-L • AGC-H
SSNR (see page 30)
• OFF • LOW • MIDDLE • HIGH
SPECIAL (see page 31)
• COLOR • SYNC • PRIVACY • RESET
• END
• EXIT
EXIT
COLOR CCD CAMERA
DOWN button
RIGHT button
1. Press the SET button to access the SETUP mode.
• SETUP menu is displayed on the monitor screen.
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
SENSE UP
GAIN
SSNR
SPECIAL
EXIT
OFF
WDR
W-ATW
OFF
LEVEL
OFF
OFF
AGC-L
MIDDLE
2. Select the desired feature using the UP or DOWN button.
• Each time you press the UP or DOWN button, the arrow indicator
moves up or down.
• Move the arrow indicator to the desired feature item.
16 User’s Manual
COLOR CCD CAMERA
17 User’s Manual
Operating Your Camera
3. Press SET button.
SETUP
Select the function using
the UP or DOWN button.
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
SENSE UP
GAIN
SSNR
SPECIAL
EXIT
OFF
WDR
W-ATW
OFF
LEVEL
OFF
OFF
AGC-L
MIDDLE
Change the status using
the LEFT or RIGHT button.
CANERA ID
POS
3. Change the status of the selected feature using the LEFT or RIGHT button.
4. When completed, move the arrow indicator to 'EXIT' and press the SET
button.
Notes
• For the mode with you can access submenu.
• You can access submenu using SET button.
4. You can enter up to 16 characters.
Move the cursor to character-enter location by using the LEFT or
RIGHT button.
Select the desired character by using UP or DOWN button.
•The factory defualt characters are A, B, ···, a, b, ···, ., -, ··· 0, 1···, 8, 9
CAMERA ID
CAMERA ID
POS
If you enter a CAMERA ID, the name will be displayed in the screen monitor.
1. Press the SET button to display the SETUP menu and move the arrow
indicator to 'CAMERA ID' using the UP or DOWN button.
2. Set 'CAMERA ID' to 'ON' using the LEFT or RIGHT button.
Notes
SETUP
• If the CAMERA ID feature is set to 'OFF', the name
will not displayed in the monitor.
COLOR CCD CAMERA
18 User’s Manual
CLR RESET END
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
SENSE UP
GAIN
SSNR
SPECIAL
EXIT
OFF
WDR
W-ATW
OFF
LEVEL
OFF
OFF
AGC-L
MIDDLE
CLR RESET END
Press the SET button to confirm the blinking character. The first
character is saved and the cursor in the bottom of the screen moves to
the next position.
Repeats steps , and until you create the full name you want.
Notes
• If you make a mistake while entering name
Move the cursor to ‘CLR’, press ‘SET’ button.
After erasing the character from right to left, correct the character again.
COLOR CCD CAMERA
19 User’s Manual
Operating Your Camera
5. Select the position at which the CAMERA ID will be located on the screen.
Move the cursor to 'POS' and press SET button.
CAMERA ID
POS
BACKLIGHT
SV-II DSP chip built-in provides intelligent light level control to overcome the
severe Backlight conditions.
1. Press the SET button to display the SETUP menu and move the arrow
indicator to ‘BACKLIGHT’ using the UP or DOWN button.
CLR RESET END
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
The CAMERA ID is displayed on the bottom-left of the monitor screen.
(Default position)
OFF
WDR
W-ATW
OFF
2. SET ‘BACKLIGHT’ to the desired mode using the LEFT or RIGHT button.
FRONT DOOR
WDR: In case that bright and dark parts exist on the screen at the same time,
your camera allows you to see both parts clearly
BLC: When the image is in front of strong background lighting, your camera
allows you to get the clear image
OFF: Deactivation
Select the position by using the 4-directional buttons, then press the SET
button to confirm the position.
WDR
FRONT DOOR
BLC
OFF
3. Press the ‘SET’ button.
• When ‘WDR’ is chosen, you can adjust the level.
WDR SET
LEVEL
0
PRESS SET TO RETURN
6. When completed, move the cursor to 'END' and press SET button.
COLOR CCD CAMERA
20 User’s Manual
You can select the level from -4 to 4. WDR sensitivity is increased or decreased.
COLOR CCD CAMERA
21 User’s Manual
Operating Your Camera
4. When completed, press the SET button.
Notes
• If you select WDR mode, the following phenomenon may appear by lighting
condition. In these cases do not select WDR mode.
Unnatural color change or unnatural phenomenon on the screen
Noise of bright part on the screen
• According to the area of bright part on the screen there may be the difference of
WDR performance so be sure to adjust the degrees of the visual angle when
installing your camera.
• If you increase WDR level, unnatural phenomenon may appear.
S-ATW(Special Auto Tracking White balance): When color temperature is
1800~6000K, specially in sodium lamp, select this mode. (EX. sodium lamp, inside the
tunnel)
AWC(Auto White balance Control): The white balance is automatically adjusted
in a specific environment. In order to obtain the best result, press the SET button while
the camera focuses on white paper. If the environment including the light source is
changed, you have to adjust the white balance again.
MANUAL: To fine adjust, select the Manual mode. You can increase or
decrease the red or blue factor while monitoring the difference on the screen. Set
to 'MANUAL' mode and press the SET button. Increase or decrease the value for
RED(R-Gain) and BLUE(B-Gain), watching the color of the picture, and press the
SET button when you obtain the best color.
Notes
WHITE BALANCE CONTROL
Your camera provides 4 ‘WHITE BAL.’ control modes. You can select the
most suitable one. You can adjust the white balance.
1. Press the SET button to display the SETUP menu and move the arrow
indicator to 'WHITE BALANCE' using the UP or DOWN button.
2. Set ‘WHITE BAL.’ to the desired mode using LEFT or RIGHT button.
• Proper White Balance may not be obtained under the following conditions, in these
cases select the AWC mode.
When the scene contains mostly high color temperature object, such as a blue
sky or sunset.
When the scene is dim.
If your camera faces fluorescent lamp directly or is installed in the place of the
changing illumination.
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
OFF
WDR
W-ATW
OFF
LEVEL
OFF
The six WHITE BALANCE control modes are as follows :
W-ATW(Wide Auto Tracking White balance): When color temperature is
2400~12000K, select this mode. (EX. a fluorescent lamp, outdoor)
COLOR CCD CAMERA
22 User’s Manual
MOTION DETECTION
Your camera transmits an alert signal when it detects motion of an object
on the screen. If you connect the camera to an external alarm, you can pay
attention to the screen when the alarm sounds. This feature is useful when
you have to monitor several screens simultaneously. Whenever your camera
detects motion of object displaying ‘MOTION DETECTED’ with the number
counted up on the screen.
1. Press the SET button to display the SETUP menu and move the arrow
indicator to 'MOTION DET.' using the UP or DOWN button.
COLOR CCD CAMERA
23 User’s Manual
Operating Your Camera
2. Set ‘MOTION DET.’ to the desired mode using LEFT or RIGHT button.
18
6
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
OFF
WDR
W-ATW
OFF
LEVEL
OFF
13
Maximum
5
Minimum
· When completed, press SET button.
MD1: Your camera detects the object’s motion by outline or difference of a
color tone, so this mode is very useful for the daytime or observing
small moving object.
Press SET button.
Move the arrow indicator to ‘AREA SET’ using UP and DOWN button, and
then press the SET button.
Set the areas you want to observe.
· You can adjust the top, bottom, left and right base lines by 13 steps
from top to bottom, 18 steps from left to right with an increment of 1.
MD2: Your camera detects object’s motion by the variation of brightness, so
this mode is very useful for night or observing large moving object.
Also MD2 enables you to set seperated areas.
Press SET button.
Move the arrow indicator to ‘AREA SET’ like MD1.
Set the areas you want to observe of the 48 areas.
· Move the cursor to the area you want to observe, and then press the SET button.
· After setting, move the cursor to edge in any direction and then press the
button just one more, let ‘END’ blink.
· Press the SET button.
Notes
· Move the arrow indicator to 'TOP' using the UP or DOWN button and
increase or decrease the value using the LEFT or RIGHT button. Repeat the
procedure for bottom, left and right.
COLOR CCD CAMERA
24 User’s Manual
• If you set some areas of 48 areas, your camera detects the object’s motion within
the areas you set.
COLOR CCD CAMERA
25 User’s Manual
Operating Your Camera
Notes
SETUP
Tips on Using the Motion Detection Feature
• As you increase or decrease MD LEVEL, the areas’ sensitivity is increased or
decreased for object.
• After selecting zone and sensitivity, perform a test operation to make sure it
works properly.
• If the lighting flickers, the motion detection feature might not work properly.
• The object should occupy 10% or more of its zone. The bigger the object, the
higher sensitivity.
• If the brightness of an object changes rapidly by sudden lighting change, the
camera may detect it as a motion.
• Your camera can count up to 999. If you reset your camera with selecting
‘RESET’ in SPECIAL menu or turn it off and on, your camera’ll count up from 0.
• When this feature is activated, another algorithm may take more time to be operated.
• This system does not guarantee prevention of fires or thefts. The manufacturer
is not responsible for any accident or damage.
• You can use the MD output terminal jack on the rear of the camera to connect
an external alarm device. For details, see page 33.
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
OFF
WDR
W-ATW
OFF
LEVEL
OFF
3. When completed move the arrow indicator to ‘END’ and press the SET button.
SHUTTER SPEED CONTROL
You can control brightness of the screen by the shutter speed.
1. Press the SET button to display the setup menu and move the arrow
indicator to ‘SHUTTER’ using the UP or DOWN button.
2. Set ‘SHUTTER’ to the desired mode using the LEFT or RIGHT button.
OFF: Deactivation
1/100(1/120: PAL Models): Flickerless mode (When WDR is on, the image
can flicker a little)
MANUAL: When setting shutter speed manually
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
SENSE UP
OFF
WDR
W-ATW
OFF
LEVEL
OFF
OFF
IRIS LEVEL CONTROL
You can control the brightness of the screen.
1. Press the SET button to display the setup menu and move the arrow
indicator to 'IRIS' using the UP or DOWN button and press SET button.
2. Set ‘LEVEL’ to the desired brightness using LEFT or RIGHT button.
COLOR CCD CAMERA
26 User’s Manual
3. If you choose ‘MANUAL’, select the optimal shutter speed.
• You can select speed from ‘1/60’ to ‘1/200,000’sec (NTSC Models), ‘1/50’
to ‘1/200,000’sec (PAL Models).
• When the shutter speed is increased or decreased using the LEFT or RIGHT
button, you can find the difference by monitoring the brightness of the screen.
COLOR CCD CAMERA
27 User’s Manual
Operating Your Camera
MANUAL SET
MANUAL SET
VALUE : 1/60
VALUE : 1/50
PRESS SET TO RETURN
PRESS SET TO RETURN
NTSC Models
PAL Models
4. When completed, press the SET button.
Notes
• If you press the set button on ‘AUTO’ mode. You can adjust brightness by increasing
or decreasing the shutter speed. (EX. x2,...., x32, x64, ...., x128)
• If you increase the number of shutter speed, moving object gets an more afterimage.
• Under SENSE UP activated noise, spots or a whitish phenomenon may appear in the
picture as the sensitivity of the camera is increased. This is normal phenomenon.
Notes
• For effective 1/100(1/120) mode set WDR mode in BACKLIGHT menu to OFF.
1/100(1/120) mode is not effective with WDR mode.
• If you choose MANUAL mode, you can’t use WDR mode in ‘BACKLIGHT’ menu.
• If you select MANUAL mode, SENSE UP is not operated.
SENSE UP
You can always get the clear image with this function under night or lowlighting level.
1. Press the SET button to display the setup menu and move the arrow
indicator to 'SENSE UP' using the UP or DOWN button.
2. Set ‘SENSE UP’ to the desired mode using the LEFT or RIGHT button.
AUTO: When your camera is under night or low-lighting level, select this mode.
OFF: Deactivation
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
SENSE UP
GAIN
COLOR CCD CAMERA
OFF
WDR
W-ATW
OFF
LEVEL
OFF
OFF
AGC-L
28 User’s Manual
GAIN
To get brighter picture.
1. Press the SET button to display the setup menu and move the arrow
indicator to ‘GAIN’ using the UP or DOWN button.
2. Set ‘gain’ to desired mode using the LEFT or RIGHT mode.
AGC-H: Gain is increased or decreased from 0 to 30dB automatically as
following the illumination.
AGC-L: Gain is increased or decreased from 0 to 27dB automatically as
following the illumination.
OFF: Deactivation
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
SENSE UP
GAIN
SSNR
SPECIAL
EXIT
COLOR CCD CAMERA
OFF
WDR
W-ATW
OFF
LEVEL
OFF
OFF
AGC-L
MIDDLE
29 User’s Manual
Operating Your Camera
SSNR(Samsung Super Noise Reduction)
To reduce the noise on the screen.
1. Press the SET button to display the setup menu and move the arrow
indicator to ‘SSNR’ using the UP or DOWN button.
2. Set ‘SSNR’ to desired mode using the LEFT or RIGHT mode.
LOW: low reduction of the noise
MIDDLE: middle reduction of the noise
HIGH: high reduction of the noise
OFF: Deactivation
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
SENSE UP
GAIN
SSNR
SPECIAL
EXIT
OFF
WDR
W-ATW
OFF
LEVEL
OFF
OFF
AGC-L
MIDDLE
Notes
• If you change the ‘GAIN’ menu from AGC-L to AGC-H, sensitivity is increased as well
as noise on the screen.
• Afterimage may appear with SSNR.
• If you select OFF on GAIN menu, SSNR doesn’t operate.
• Incidental image will be displayed more obviously according to SSNR step from
LOW to HIGH.
SPECIAL
1.Press the SET button to display the setup menu and move the arrow
indicator to ‘SPECIAL’ using the UP or DOWN button.
2. Press the SET button.
COLOR : choose color or B/W mode electrically
- ON : color mode
- OFF : B/W mode
- AUTO1 : generally color mode, B/W mode in low luminance.
- AUTO2 : AUTO2 is identical with AUTO1 under SENSE UP : AUTO condition.
SYNC : Two SYNCHRONIZATION modes are available INTERNAL and
EXTERNAL LINE-LOCK. In LINE-LOCK mode, it synchronizes the
video signal between cameras without a synchronous generator.
The line-lock synchronization is only used in the areas of 60Hz
(NTSC Models) / 50Hz (PAL Models).
- INT : Internal synchronization
- OFF : External line-lock synchronization
· If you choose ‘L/L’, you can adjust the desired phase. Press the SET button.
-You can adjust the desired phase from 0 to 270.
LINE LOCK
PHASE : 225
PRESS SET TO RETURN
COLOR CCD CAMERA
30 User’s Manual
COLOR CCD CAMERA
31 User’s Manual
Operating Your Camera
Notes
• When the power frequency is 50Hz, you can not use line-lock mode(NTSC Models).
• When the power frequency is 60Hz, you can not use the line-lock mode(PAL Models).
• ‘Sync.’ mode is fixed to ‘INT’ in DC 12V input power.
PRIVACY: To mask area which you want to mask
- OFF: Deactivation
- ON: Privacy mode activated
· Press the SET button.
Using Remote Jack / MD Output
If you connect a remote plug to the REMOTE jack on the rear of the camera
as shown below, you can access the menu setup mode from a remote place.
1. RS-232C Communication Setting.
• Mode : Serial • Data Bit : 8 • Bit/sec : 19200bps
• Port : Com1
• Parity : None
• Stop Bit : 1
2. Setup menu Command.
· Move the arrow indicator to area you want to mask.
· Set ‘ON’ using LEFT or RIGHT button.
· Press the SET button and then set the area’s bounds with the method like
MD1 Set. (see page 24)
· When completed, press the SET button.
Setup menu
Set
Up
Down
Left
Right
Command
AA, EE, 0F, CC, 55
AA, EE, 1E, CC, 55
AA, EE, 1D, CC, 55
AA, EE, 1B, CC, 55
AA, EE, 17, CC, 55
Byte
5
5
5
5
5
3. MD(MOTION DETECTION) output Signal Level (Less than 10mA)
+4.0V~+5.0V
There is motion
RESET: To reset your camera to factory default condition
0V
There is no motion
END: To move Top-menu
EXIT: To finish setting menu
2.5±0.5sec
Notes
• You must turn the camera power off when you connect or remove the remote plug.
COLOR CCD CAMERA
32 User’s Manual
COLOR CCD CAMERA
33 User’s Manual
Troubleshooting
If you have trouble operating your camera, refer to the following table. If the
guidelines do not enable you to solve the problem, contact an authorized
technician.
Problem
Solution
Nothing appears on
the screen.
• Check that the power cord and line connection
between the camera and monitor are fixed properly.
• Check that you have properly connected VIDEO
cable to the camera VIDEO output jack.
The image on the
screen is dim.
• Is lens stained with dirt? Clean your lens with soft,
clean cloth.
• Set the monitor to proper condition.
• If the camera is exposed to too strong light, change
the camera position.
• Adjust the lens’ focus properly.
The image on the
screen is dark.
• Adjust the contrast feature of the monitor.
• If you have an intermediate device, set the 75Ω / Hi-z
properly. (refer to page 14)
The camera is not
working properly, and
the surface of the
camera is hot.
• Check that you have properly connected the camera
to an appropriate power source.
MOTION DETECTION
function is not active.
• Have you set ‘MOTION DET.’ menu to OFF?
• Have you set ‘MD LEVEL’ to too low?
• Have you set ‘MD AREA’ properly?
COLOR CCD CAMERA
34 User’s Manual
Problem
Solution
The color of the picture
is not matched.
• Check that you have properly set the ‘WHITE BAL.’
menu. (refer to page 22)
The image on the screen
flickers.
• Is the camera facing to direct sunlight or fluoresent
lighting? Change the camera position.
L/L mode isn’t able to
be selected.
• Have you connected your camera to DC power
source? Connect it to AC power source.
COLOR CCD CAMERA
35 User’s Manual
DECLARATION OF CONFORMITY
Specifications
SOC-4120AN
Item
Power Source
SOC-4120AP
DC 12V / AC 24V compatible
Power Consumption
89 / 336 / EEC
Manufacturer's Name
SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
280mA (DC) / 3.8 W (AC)
Image Sensor
Application of Council Directive(s)
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
1/3", Vertical double density interline CCD
Total Pixels
811(H) x 508(V), 1/3" CCD
795(H) x 596(V), 1/3" CCD
Effective Pixels
768(H) x 494(V), 1/3" CCD
752(H) x 582(V), 1/3" CCD
LENS TYPE
KYUNGNAM, KOREA, 641-120
European Representative Name
X2.5 Vari-Focal, f=3.8~9.5
Maximum Aperture Ratio
European Representative Address
1:1.3~2.0
Angle of View
H: 74.2˚ ~ 30.0˚, V: 54.0˚ ~ 22.4˚, D: 96.8˚ ~ 37.4˚
Scanning System
2:1 Interlaced 525 Lines/60 Fields/30 Frames
Synchronization
2:1 Interlaced 625 Lines/50 Fields/25 Frames
Internal / Line Lock selectable
Video Output
1.0V[p-p] NTSC Composite, 75Ω / BNC Connector
Resolution
1.0V[p-p] PAL Composite, 75Ω / BNC Connector
500TV Lines
Wide Dynamic Range
ON / OFF / AUTO
Gain Control
Equipment Type/Environment
CCTV Camera
Model Name
SOC-4120AN/P
Beginning Serial NO.
S4200001
Year of Manufacture
2004. 2. 1
Conformance to
EN 50081-1 : 1992
AGC-L, AGC-H, OFF Selectable
Electronic Shutter Speed
1/60~1/200,000sec
SENSE UP
EMC-Directive 89/336 EEC and 92/31/EEC
1/50~1/200,000sec
EN 50130-4 : 1996
Built-in (selectable limit~X128)
IRIS MODE
DC Drive
WHITE BALANCE
W-ATW / S-ATW / AWC / MANUAL
S/N (Y signal)
50dB (Weight On)
SSNR
We, the undersigned, hereby declare that the equipment specified above conforms
LOW / MIDDLE / HIGH / OFF
RS-232C
Built-in
MOTION DETECTION
MD1 / MD2 / OFF (Built-in Alarm Output Connector)
O.S.D
Built-in
PRIVACY Function
to the above Directive(s).
SAMSUNG TECHWIN CO., LTD
Legal Representative in Europe
Full Name
YOUNG TAEK SON
Full Name
Position
QUALITY CONTROL MANAGER
Position
Place
CHANGWON, KOREA
Place
Date
2004. 2. 1
Date
Manufacturer
Signature
Signature
ON / OFF (4 Programmable Zone)
Operating Temperature
-10°C ~ +50°C (14°F ~ 122°F)
Operating Humidity
30% ~ 90% RH
Dimension (mm)
63(W) X 58(H) X 157(D)
Weight (W/O Lens & Power Cord)
COLOR CCD CAMERA
350g
36 User’s Manual
COLOR CCD CAMERA
37 User’s Manual
MEMO
MEMO