Miele T 234 C Operating instructions

Operating instructions
for condenser tumble dryer
T 234 C
To avoid the risk of accidents
or damage to the machine
it is essential to read these
instructions before it is installed
and used for the first time.
G
M.-Nr. 06 465 690
Caring for the environment
Disposal of the packing
material
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of your
appliance with your household waste.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person. The plug must be
rendered useless and the cable cut off
directly behind it to prevent misuse.
See the "Warning and Safety" section of
this booklet for further details.
Energy saving tips
To avoid unnecessarily long drying
times and high consumption of energy:
– Make sure that your laundry is
thoroughly spun before drying.
The higher the spin, the greater the
savings that can be made in energy
and time during drying.
– Load according to the optimum
amount of laundry recommended for
the programme being used (see
Programme chart).
Underloading is uneconomical.
Overloading gives a poorer quality of
drying and may cause unnecessary
creasing.
– Make sure the room in which the
dryer is located is well ventilated.
– Make sure the fluff filters are clean
before using the dryer.
– Check the condenser unit from time
to time and clean it when necessary.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
2
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Disposal of the packing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Disposal of your old appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Energy saving tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Notes on laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Care symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Tips on drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
How to dry correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Brief instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Low temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Changing the programme sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Emptying the condensed
water container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cleaning the fluff filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cleaning them whilst dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cleaning them with water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Cleaning the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Cleaning the condenser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Removing the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Checking the condenser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Cleaning the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Replacing the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Problem solving guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
General problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Check and fault indicator lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Changing the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3
Contents
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Repairs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Appliance guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Transporting the machine to its installation site . . . . . . . . . . . . . . . . . . . . . . . . 30
Building under a continous worktop / in a row of kitchen units . . . . . . . . . . . . 30
Replacing the lid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Levelling the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Room in which the dryer is located . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Washer - dryer stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Before moving the machine again (e.g. when moving house) . . . . . . . . . . . . . 31
External condensed water outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Setting up the drain hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Connection to a sink drain outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
If you no longer wish to use an external condensed water outlet . . . . . . . . . . 33
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Electrical connection U.K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Altering the residual moisture level in the Cottons programmes . . . . . . . . . . . . . . 38
Altering the residual moisture level in the Minimum iron programmes . . . . . . . . . 39
Activating and deactivating the buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Extending the cooling down time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Changing the standard drying level in the Minimum iron - Normal programme . . 42
Changing the standard drying level in the Automatic programme . . . . . . . . . . . . 43
4
Warning and Safety instructions
Technical safety
To avoid the risk of accidents and
damage to the machine please read
these instructions carefully before
using it for the first time. They
contain important information on its
safety, installation, use and
maintenance.
Keep these instructions in a safe
place and ensure that new users are
familiar with the content. Pass them
on to any future owner of the
machine.
Correct use
The tumble dryer is only intended
for drying fabrics which have been
washed in a water solution, marked on
the manufacturer's care label as being
suitable for tumble drying.
"Dry cleaning kits" for freshening up
garments in a tumble dryer are
increasingly available on the market. If
using, do so at your own risk, and
follow the instructions provided on the
packaging.
Any other applications may be
dangerous. The manufacturer is not
liable for damage resulting from
improper use or operation.
Before setting up the machine,
check it for any externally visible
damage.
Do not install or use a damaged
machine.
Before connecting the machine,
ensure that the connection data on
the data plate match the mains
electricity supply. If in any doubt,
consult a qualified electrician.
The electrical safety of this
machine can only be guaranteed
when continuity is complete between it
and an effective earthing system which
complies with local and national safety
regulations. It is most important that this
basic safety requirement is present and
regularly tested, and where there is any
doubt the household wiring system
should be inspected by a qualified
electrician. The manufacturer cannot be
held liable for the consequences of an
inadequate earthing system (e.g.
electric shock).
Do not connect the machine to the
mains electricity supply by an
extension lead. Extension leads do not
guarantee the required safety of the
appliance (e.g. danger of overheating).
5
Warning and Safety instructions
The machine is built in accordance
with current safety requirements.
Unauthorised repairs could result in
unforeseen dangers for the user, for
which the manufacturer cannot accept
liability. Repairs should only be
undertaken by a Miele approved
technician.
Ensure current is not supplied to the
machine until after maintenance or
repair work has been carried out.
Faulty components must only be
replaced by genuine Miele original
spare parts. Only when these parts are
fitted can the safety standards of the
machine be guaranteed.
If the connection cable is faulty it
must only be replaced by a Miele
approved service technician to protect
the user from danger.
In countries where there are areas
which may be subject to infestation
by cockroaches or other vermin, pay
particular attention to keeping the
machine and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not be
covered by the machine guarantee.
6
Warning and Safety instructions
In the event of a fault or for
cleaning purposes, the machine is
only completely isolated from the
electiricty supply when:
– it is switched off at the wall socket
and the plug is withdrawn, or
– it is switched off at the mains, or
– the mains fuse is withdrawn, or
– the screw-out fuse is removed (in
countries where this is applicable).
Operation
This equipment may only be used
in mobile installations such as
ships, caravans, aircraft etc. if a risk
assessment of the installation has been
carried out by a suitably qualified
engineer.
The ambient room temperature should
be between +2°C and +35°C.
If the water is drained externally
through the drain hose instead of
being collected in the condensed water
container, make sure the drain hose is
securely attached if you hang it in a
sink or basin to avoid the hose slipping
and the water causing damage.
Condensed water is not drinking
water. It can cause health
problems in both people and animals.
Always keep the area around the
machine free of dust and fluff. Dust
drawn into the machine can, over time,
cause blockages in the condenser unit.
The dryer must not be used without
the fluff filters in place or if the fluff
filters are damaged in any way.
The fluff filters must be thoroughly
dried after cleaning. If they are still
damp or wet when replaced there is a
risk of faults occurring when the
machine is used.
The dryer must not be used without
the condenser unit in place.
Do not install the machine in a
room where there is a risk of frost
occurring. At temperatures around
freezing point the machine may not be
able to operate properly.
There is a risk of damage if the
condensed water is allowed to freeze in
the pump, hoses and / or condensed
water container.
7
Warning and Safety instructions
To prevent the risk of fire the
following textiles must not be
dried in this machine:
– fabrics which contain a large
proportion of rubber, foam rubber or
rubber like materials.
– items which contain damaged
padding or fillings (e.g. pillows,
jackets).
– items which have been treated with
inflammable cleaning agents.
– items which have been splashed with
hair lacquer, hair spray, nail varnish
remover or similar substances.
– items which have been soiled with
oils or residues containing grease
(kitchen oils, cosmetics etc.).
– items soiled with wax or other
chemicals (e.g. mops and floor
cloths).
– items which have not been
thoroughly cleaned and which are
still soiled with grease or oil, e.g.
workwear. Such clothing may require
a heavy duty detergent to get them
clean. If necessary consult the
detergent manufacturer for advice.
Do not let anyone sit or lean on the
door, as this can cause the
machine to tip up.
Always close the door after use.
This way you will avoid the danger
of:
– children climbing onto or into the
dryer or hiding things in it.
– pets or other small animals climbing
into it.
8
Safety with children
This machine is not a toy. To avoid
the risk of injury keep children
away from the machine at all times and
supervise them whilst you are using it.
Do not allow children to play on or near
it or to play with its controls. Supervise
its use by the elderly or infirm.
Using accessories
Accessory parts may only be fitted
when expressly approved by Miele.
If non-Miele parts are used with this
machine, guarantee, performance and
product liability claims may be
invalidated.
Disposal of your old machine
Before discarding an old machine,
switch it off at the wall socket and
unplug it. Render the plug useless and
cut off the cable directly behind the
machine. This should be done by a
competent person.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
Control panel
a Programme selector
The programme selector can be
turned clockwise or anti-clockwise.
b Programme sequence and check
lamps
c Start button
Press the Start button to start a
programme.
The Start indicator lamp will flash as
soon as a programme can be
started. It lights up constantly once
the programme has started.
d I-On/0-Off button
To switch the machine on or off / to
interrupt a programme.
e Door Button
To open the door / to cancel a
programme.
Pressing this button will open the
door even when the machine is
switched off at the mains.
If the machine is switched on at the
mains and the door is opened the
drum lighting will come on. It will go
out a few minutes later to save
energy.
PC indicator light
The indicator light marked PC is used
by Miele Service technicians as an
optical interface.
The Anti-crease/Finish lamp will light
up as confirmation that the machine
has been switched on.
9
Notes on laundry care
Care symbols
Before drying check the drying symbol
on the care label. If there are no
symbols, dry at your own risk!
q . . . . . . . . . Dry at normal temperature
r . . . . . . . . . . Dry at a low temperature
s . . . . . . . . . . . . . . . Do not tumble dry
– For delicates and fabrics with the
following care label r select Low
temperature.
Tips on drying
– Always observe the maximum
recommended loads given in the
"Programme chart". Never overload
the drum.
Overloading can cause unnecessary
wear and tear to the laundry, give a
disappointing drying result and
cause more creasing.
– Do not put soaking wet items into the
tumble dryer. Spin them thoroughly
after washing using the appropriate
spin speed.
– Use the Automatic programme for
drying mixed loads of cottons and
minimum iron fabrics.
– Open jackets so that they can dry
evenly.
– Woollens and wool blends tend to
become matted and shrink if dried in
a tumble dryer. They can, however,
be partially dried using the Woollens
hand care programme.
10
– Down-filled garments have linings
which have a tendency to shrink,
depending on the quality of the item.
They can be partially dried using the
Smoothing programme.
– Pure linen should only be machine
dried if specified as suitable by the
manufacturer on the care label, as
the surface of the fabric may
otherwise become rough. They can
be partially dried using the
Smoothing programme.
– Loopknit garments (e.g. T-shirts and
underwear) tend to shrink depending
on their quality. Do not over-dry these
textiles. When purchasing these
garments it is advisable to take their
shrinkage properties into account.
– Minimum iron fabrics and 100%
cotton shirts or blouses tend to
crease more, the greater the load.
This is especially true of very fine
weaves.
Reduce the load or use the Minimum
iron - Hand iron programme.
– Starched laundry can be dried in the
tumble dryer. To achieve the usual
finish, double the amount of starch
should be used.
– New dark coloured garments should
be washed and dried separately
from light coloured garments to avoid
the danger of colours running and
discolouring other garments or even
plastic components in the machine.
Dark coloured fibres can also settle
on light coloured garments and vice
versa.
How to dry correctly
Brief instructions
C Load the tumble dryer
The headings numbered (A, B, C ...)
show the operating sequence and can
be used as a brief guide to using your
machine.
^ Press the Door button to open the
door.
^ Load the laundry loosely into the
drum.
A Sort the laundry
To ensure an even drying result
separate out the washed laundry and
sort it according to: . .
. . . the drying level required
. . . the type of fibre or weave
. . size
. . the moisture content after spinning.
,Make sure that objects e.g.
detergent dispensing balls have
been removed from the laundry.
They could melt, and cause damage
to the dryer or the laundry.
Do not overload the drum. See the
"Programme chart" for
recommended loads for each
programme.
Overloading can cause unnecessary
wear and tear to the laundry and
give a disappointing drying result.
^ Before closing the door make sure
the fluff filter is correctly positioned.
– Check seams and stitching to ensure
that padding and linings are intact.
– Fasten duvet covers and pillow
cases to prevent small items from
being trapped inside them.
– Fasten hooks and eyes etc.
– Tie fabric belts and apron strings.
– Sew in or remove underwiring from
bras.
B Turn on the tumble dryer
^ Switch the dryer on by pressing the
I-On/0-Off button in.
The tumble dryer may be switched on
after loading, saving energy as the light
will not come on.
Check the laundry is right inside the
drum so that it cannot get trapped or
damaged when the door is shut.
^ Shut the door either with a gentle
swing, or lean against it and push it
shut.
11
How to dry correctly
D Select a programme
E Start the programme
^ Press the Start button.
The indicator lamp for the Start button
will then change from flashing to being
on constantly.
The drying cycle begins.
Depending on the programme
selected, the drying stage reached is
shown by the sequence indicator lamps
on the right hand side of the control
panel.
Before the end of a programme
^ Turn the programme selector to the
required programme.
Low temperature
^ For drying particularly sensitive
fabrics (care symbol r) e.g. acrylics
turn the programme selector to the
Low temperature position.
Because the heater rating is reduced
for the Low temperature setting clothes
dry more slowly thus lengthening drying
times.
The cooling down phase takes place
before the end of a programme so that
the garments are not too hot to handle
(the Cool air indicator lamp will come
on). The programme is not finished until
the cooling down phase is complete.
At the end of a programme
The Anti-crease/Finish indicator lamp
comes on.
The drum will continue to rotate at
intervals to prevent laundry creasing, if
you do not wish to remove it immediately. The anti-crease phase lasts for an
hour. There is no anti-crease phase on
the Woollens handcare programme.
During the anti-crease phase . . .
. . . (depending on the programme
selected) the indicator lamp for the
drying stage reached will also light up.
. . . the buzzer will sound at intervals.
12
How to dry correctly
F Remove the laundry
^ Press the Door button.
^ Open the door.
^ Remove the laundry.
Make sure that the drum is empty. If
items are left in the dryer, they could
be damaged by overdrying when
the dryer is next used.
^ Switch the dryer off by pressing the
l-On/0-Off button.
^ Clean the fluff filters.
^ Close the door.
^ Empty the condensed water
container (where there is no external
drainage of the water).
^ The condenser unit should be
checked and cleaned on a regular
basis.
^ Switch the dryer on with the
I-On/0-Off button.
The programme will continue (only with
the Cottons, Minimum iron and Automatic programmes).
Other programmes:
^ Press the Start button.
To cancel a programme
^ Turn the programme selector to
Finish or open the door.
Adding or removing laundry after a
programme has started
^ Press the Door button.
^ Open the door.
,Do not touch the back of the
drum when adding or removing
items. The drum could be very hot danger of burning.
Changing the programme
sequence
^ Add or remove items.
Changing a programme while it is
running
^ Press the Start button.
^ Close the door.
As long as the cooling down phase or
the anti-crease phase has not been
reached, it is possible to change a
programme after it has started by
turning the programme selector to a
different programme position.
To interrupt a programme
^ Switch the machine off with the
I-On/0-Off button.
To continue drying:
13
Programme chart
Max. load: 6 kg*
Cottons
Normal+, Normal**, Low temperature
Fabric
Single and multi-layered cottons fabrics such as towelling, jerseywear,
type
underwear, flannelette bed linen.
– Select Low temperature for fabrics with the r symbol. Laundry is
dried at a lower temperature.
Hand iron**, Machine iron
Fabric
Cottons and linen fabrics, e.g. table linen, bedlinen, starched laundry.
type
Note
To prevent laundry from drying out it should be rolled up until you are
ready for ironing.
Note
Minimum iron
Normal**, Low temperature, Hand iron
Fabric
type
Max. load: 3 kg*
Minimum iron items made of cotton, synthetic or blended fabrics, e.g.
shirts, blouses, skirts and table cloths.
– Select Low temperature for fabrics with the r symbol (e.g. acrylic
garments). Laundry is dried at a lower temperature.
– Select Hand iron for delicate fabrics and to reduce creasing even
more, reduce the load to 1.5 kg*.
– In the Miniumum iron Hand iron programme, items are dried with
very little creasing, depending on fabric type and amount of load.
*
Weight of dry laundry
** Note for test institutes:
Programme setting for testing in accordance with EN 61121
Notes
14
Programme chart
Automatic
Fabric
type
Mixed load of cotton and minimum iron fabrics.
Timed drying
Warm air
Fabric
type
Max. load: 3 kg*
Max. load: 6 kg*
– Multi-layered fabrics whose layers have different drying
characteristics, e.g. jackets, pillows.
– For drying individual items, e.g. bath towels, bathing costumes,
tea-towels.
Cool air
Fabric
type
Any item which only needs airing.
Woollens handcare
Max. load: 2 kg*
Fabric
Woollen fabrics
type
Notes
– To refresh and fluff up woollen garments quickly. Woollen fabrics
are not dried completely by this programme.
– Remove garments as soon as the programme has finished and
leave to finish drying at room temperature.
Smoothing
Max. load: 3 kg*
– Cottons and linen fabrics.
Fabric
type
– Minimum iron items made of mixed fibres, cottons or synthetics e.g.
trousers, jackets, shirts.
– Smooths out creasing caused during the spin cycle in the washing
Notes
machine.
– Fabrics are not completely dried in this programme. Remove
garments as soon as the programme has finished and leave to
finish drying at room temperature.
*
Weight of dry laundry
15
Cleaning and care
Emptying the condensed
water container
The condensed water will be collected
in the condensed water container
unless the machine has been fitted with
a drain hose (see installation).
The condensed water container
should be emptied after every
drying cycle or as soon as the
Empty out container indicator lamp
comes on.
The drying programme will be
interrupted if the maximum level of the
condensed water container is reached.
The Empty out container indicator lamp
comes on and the buzzer sounds.
^ Open the shutter and empty out the
water.
^ To replace the container hold it at a
slight angle (as when removing it)
and push it in gently until you feel it
click into position.
^ Before starting a new programme,
first switch the machine off and then
on again. The Empty out container
indicator lamp will go out.
Condensed water should not be
consumed. It could lead to health
problems for people and animals.
^ Grip the container firmly with both
hands, as shown, and pull it out
slightly towards the right-hand side.
^ Hold the container with both hands
and carry it in a horizontal position.
16
Condensed water can be put to
household use (e.g. used in a steam
iron or humidifier). To ensure that any
residual particles of fluff in the
condensed water are removed before
use, pass it through a fine sieve or
paper filter first.
Cleaning and care
Cleaning the fluff filters
The fluff which is created by the drying
process is collected by the fluff filters in
the door and the door opening. Clean
the filters after each drying programme.
Cleaning them whilst dry
Tip: You can also use a vacuum
cleaner.
^ Remove any fluff from the hollow part
of the door holder. A cleaning brush
is available as an optional extra from
your Miele dealer or the Miele Spare
Parts Department, or use a vacuum
cleaner.
^ Once clean, push the filter back into
the door holder until it clicks into
position. Ensure it is facing the
correct way.
^ Also clean the door seal (2) with a
damp cloth.
^ Open the door and pull the fluff filter
(1) out of the door as illustrated.
^ Use your fingers to remove the fluff
from the two fluff filters in the door
opening.
^ Close the door.
^ Use your fingers to remove the fluff
from the surface of the filter.
17
Cleaning and care
Cleaning them with water
If there is a great deal of compacted
fluff on any of the filters, they can be
removed and cleaned under hot
running water.
^ To remove the fluff filter from the door
holder see previous page.
^ Place the filters back in the door
opening (the left and right filters are
identical) with the finger holders
facing upwards. See illustration.
Cleaning the tumble dryer
Disconnect the machine from the
mains electricity supply.
^ Clean the housing and control panel
with a slightly damp cloth and a mild
detergent or soapy water.
^ The drum and other stainless steel
parts can be cleaned with a suitable
proprietary stainless steel cleaner
following the manufacturer's
instructions.
^ To remove the filters in the door
opening, grip the holder and push
upwards in the direction of the arrow
to remove it.
^ Rinse the filters under hot, running
water.
^ Then shake the filters until no more
water droplets are visible.
^ Dry the filters thoroughly with care.
,Do not replace them if they are
damp or wet. Damp or wet filters
could cause operational faults.
^ Push the large filter back into the
door holder until it clicks into position.
Ensure it is facing the correct way.
18
Do not use solvents, abrasive
cleaners, glass cleaners or
all-purpose cleaners. These could
damage plastic sufaces and other
parts. The machine must never be
hosed down.
^ Dry all parts with a soft cloth.
^ A microfibre E-Cloth is available from
the Miele UK Spare Parts Department
which is suitable for cleaning
surfaces such as stainless steel,
glass, plastic and chrome without the
use of chemicals. It can be washed
300 times.
Cleaning and care
Cleaning the condenser unit
Detergent residue, hair and fine fluff
from the dryer can get through the fluff
filters and block the condenser unit.
Dust from the room in which the dryer is
installed can also get into the
condenser unit and cause a blockage.
Check the condenser unit at least
twice a year. If the dryer is used
frequently then clean the condenser
unit after approx. 100 drying cycles.
Removing the condenser unit
^ Turn the lever on the inner cover
downwards to the vertical position.
^ Pull the cover forwards
^ Then remove it by pulling it
diagonally upwards.
^ Open the service panel.
The hooks at the side will prevent the
panel from falling off.
^ Now remove the panel by pulling it
diagonally upwards.
^ Turn the lever on the condenser unit
to the vertical position.
^ Then place it to one side.
19
Cleaning and care
If you cannot see any fluff:
^ Replace the condenser unit (see
following page).
If you can see some fluff:
^ Clean the condenser unit as
described below.
Cleaning the condenser unit
^ When rinsing the condenser unit,
make sure you position it as shown
in the next two illustrations.
^ Pull the condenser unit out of its
housing by the handle.
Checking the condenser unit
^ Use a shower head or similar to rinse
the unit out as shown.
^ Hold the condenser unit up to the
light as shown.
^ Check to see if there is any fluff
inside it.
The arrows in the illustration above
indicate where to look.
20
Cleaning and care
Replacing the condenser unit
^ With the handle facing upwards,
push the condenser unit back into
position in its housing.
^ Turn the lever down to the horizontal
position, making sure that the hook
on the lever clicks into the groove.
When replacing the inner cover after
cleaning, ensure that the rubber seal
fits correctly into the groove.
^ Then flush the unit through from the
front.
^ Check the condenser unit again for
any visible fluff and if necessary flush
it through again until it has all gone.
^ Remove any soiling still visible inside
the housing unit by hand using a
damp cloth. Do not try and access
areas you cannot reach by hand!
^ Also make sure the rubber seals are
clean.
The rubber seals must not be
removed and must be free of kinks.
^ Replace the inner cover making sure
the hooks locate correctly. Hold it at
an angle and push it gently
downwards.
^ Then turn the lever upwards into the
horizontal position to lock the cover.
^ Replace the service panel and press
the upper edge until it clicks into
position.
,It is important to ensure that both
the condenser unit and the cover are
correctly positioned and locked
otherwise water may leak from the
machine.
21
Problem solving guide
With the help of the following notes minor faults in the performance of the
machine, some of which may result from incorrect operation, can be put right
without contacting the Service Department.
,Repair work to electrical appliances should only be carried out by a
suitably qualified person in strict accordance with local and national safety
regulations. Repairs and other work by unqualified persons could be
dangerous. The manufacturer cannot be held liable for unauthorised work.
General problems
Problem
Possible cause
The tumble dryer fails to No obvious cause.
start when switched on.
Items made of synthetic Synthetic fibres tend to
fibres are charged with attract static charge.
static electricity after
drying.
22
Remedy
– Have you followed the
switch-on procedure
correctly (see “How to
dry correctly”)?
– Is the plug correctly
inserted in the socket
and switched on?
– Is the door closed
properly?
– Has the fuse or circuit
breaker tripped?
Static charge can be
reduced by adding a
fabric conditioner to the
final rinse in the washing
machine or a fabric
conditioner sheet to the
load in the dryer.
Problem solving guide
Problem
Possible cause
Remedy
There is a build
up of fluff.
Fluff is principally the result of
friction when garments are
being worn and washed.
Machine drying hardly
causes any fluff to form and
has been established by
research institutes to have no
appreciable effect on the
lifetime of the garment.
The load consisted of
different fabrics.
Fluff is collected by the fluff
filters and can be easily
removed (see "Cleaning and
care").
The laundry is
not sufficiently
dry.
The interior
drum lighting
does not come
on.
– Finish drying using "Warm
air" (timed drying).
– Select a more suitable
drying programme next
time (see "Programme
chart").
The lighting switches off
automatically (to save
energy).
Switch the dryer off and then
on again.
The lamp needs changing.
Change the lamp as
described at the end of this
section.
23
Problem solving guide
Problem
Possible cause
Remedy
The drying process Important: Before attempting to remedy one of the
goes on too long or following causes, switch the dryer off and switch on again
even switches off. to start the programme again.
Ventilation to and from the
Open a door or window
while the machine is in
dryer may be insufficient
(e.g. because it is installed operation for increased air
in a small room). This has
flow.
caused the temperature in
the room to rise sharply.
The vents below the door
– Remove any objects that
are blocked.
are blocking the vents.
The fluff filters are clogged – Remove any fluff.
up with fluff or were still wet – The fluff filters must be
when they were replaced.
completely dry.
Detergent residues, hair and Check the condenser unit
fine fibres can block up the from time to time and clean
condenser unit.
it if necessary (see
"Cleaning and care").
The laundry has not been
spun sufficiently.
Make sure that your laundry
is thoroughly spun at the
appropriate spin speed.
The tumble dryer has been
overloaded.
Do not exceed the maximum
load for the programme
selected.
– Open zips next time.
If the problem occurs again,
dry garments with long zips
using "Warm air" (timed
drying).
Metallic components, e.g.
zips have prevented the
dryer from registering the
correct moisture level in the
laundry.
24
Problem solving guide
Problem
Possible cause
Remedy
The condenser unit
The inner cover of the
– Ensure that the condenser
service panel will not condenser unit has not
unit is positioned correctly
shut.
been locked properly
and lock the cover.
and/or the condenser
– Check the rubber seals.
unit has not been
positioned correctly.
Water leaks from the Fluff has collected at
– Use a cloth to remove any
machine after the
the bottom of the
fluff from the inside of the
condenser unit has
condenser unit housing.
condenser unit housing.
been cleaned.
Check and fault indicator lamps
Problem
The Empty out
container indicator
lamp comes on.
Possible cause
Remedy
The condensed water
– Empty out the condensed
container is full or there
water container.
is kink in the drain hose. – Check the drain hose.
– Before starting a new
programme, first switch the
dryer off and then on again.
– Switch off the dryer.
The programme has There is no obvious
been interrupted, the cause.
– Then switch the dryer back
indicator lamp for
on and start the programme
Hand iron or Machine
again.
iron is flashing, and
If the programme stops again
the buzzer sounds.
and an indicator lamp flashes,
there is a fault. Contact the
Miele Service Department.
25
Problem solving guide
Problem
Possible cause
Remedy
The programme has
stopped, the
Anti-crease/Finish lamp
has come on in the
sequence display and
the buzzer is sounding.
This is not a fault.
The electronic unit has
recognised that there is
no laundry in the drum
and cancelled the
programme.
Drying individual
garments or items which
are already dry can also
cause the programme to
be stopped.
Use the "Timed drying Warm air" programme to
dry individual items.
Before changing a
programme: Open and
close the drum door.
26
Problem solving guide
Changing the lamp
Disconnect the machine from the
mains electricity supply.
The lamp specification and
maximum wattage is stated on the
data plate and on the lamp cover.
^ Open the door.
^ Replace the lamp.
You will find the interior lamp cover at
the top of the drum aperture.
^ To close the cover push it upwards
and press it on the left and right until
you hear it click into position.
,Ensure that it is fitted into
position securely, as any moisture
could cause a short circuit.
^ Insert a suitable tool, such as a wide
bladed screwdriver, under the side
edge of the lamp cover as illustrated.
^ Apply a little pressure and whilst
doing so turn your wrist in the
direction of the arrow to open the
cover.
The cover will open downwards.
The temperature resistant lamp should
only be ordered from your Miele dealer
or the Miele Spare Parts Department.
27
After sales service
Repairs
Appliance guarantee
In the event of any faults which you
cannot remedy yourself, or if the
machine is under guarantee, please
contact
Please see the guarantee card
supplied with your machine.
– your Miele dealer, or
Optional accessories for this dryer is
available from your Miele Dealer or from
the Miele Spare Parts Department.
– the Miele Service Department
(see back cover for contact details).
When contacting your Dealer or the
Service Department, please quote the
model and serial number of your
machine, both of which are shown on
the data plate situated on the right
hand side below the drum aperture.
28
Optional accessories
Please note that telephone calls may
be monitored and recorded to
improve our service.
Installation
Front view
a Mains connection cable
e Service panel for condenser unit
b Condensed water container
f Four height-adjustable screw feet
c Control panel
g External drainage options (e.g. via
wash basin, wash basin drain outlet,
or gully).
d Door
29
Installation
Installation site
,Make sure the dryer door can be
opened without hindrance after
installation.
Transporting the machine to its
installation site
When moving the machine you can
hold it by the lid where it protrudes to
the rear of the dryer.
To manoeuvre the dryer out of its
packing case to its installation site you
will also need to hold it by the front feet.
Building under a continous worktop /
in a row of kitchen units
The dryer should not be installed
next to a refrigerator or freezer. The
warm air expelled from the rear of
the dryer would increase the
temperature around the
refrigerator's/freezer's heat
exchanger causing the compressor
to run continuously.
If it is not possible to install the dryer
anywhere else, then the
refrigerator/freezer must be sealed
off from the dryer.
If you wish to push your machine under
a worktop and there is space to do this
without removing the lid, a building
under kit is not necessary. Otherwise
the building under kit is essential.
,The building under kit* must be
fitted by a suitably qualified person.
The machine lid is replaced by a
coverplate. It is essential that the
coverplate is fitted to ensure
electrical safety.
The building under kit is supplied with
its own installation instructions.
N.B. When built under running times
may be longer.
– The electrical socket must be
located in an accessible position
near the machine.
With niche heights of:
– 840 mm, longer screw feet* are
required.
– 870/885 mm - 915/930 mm, one or
two height adjustment frames* are
required.
* Available as an optional accessory
from your Miele dealer or the Miele
Spare Parts Department.
Replacing the lid
If the lid has been removed in order to
fit a cover plate, ensure that, if the lid is
replaced, it fits securely into the rear
holders. Otherwise, it is not properly
secure for transport.
30
Installation
Levelling the machine
Room in which the dryer is located
Air taken in for use in the drying
process will be warm when it is
expelled from the rear of the dryer. This
expelled air heats up the air in the
room. It is therefore very important to
ensure that the room is adequately
ventilated, particularly if the dryer is
located in a small room. Otherwise
running times and energy consumption
could be increased.
Washer - dryer stack
The machine must be perfectly level to
ensure safe and proper operation.
The tumble dryer can also be
combined with a Miele washing
machine in a washer-dryer stack. To do
this the appropriate stacking kit* (WTV)
to match your washing machine is
required.
* Available as an optional accessory
from your Miele dealer or the Miele
Spare Parts Department.
,Stacking kits must be fitted by a
suitably qualified fitter.
Before moving the machine again
(e.g. when moving house)
^ The screw feet can be adjusted to
compensate for any unevenness in
the floor.
,The ventilation gaps in the plinth
must not be covered over as this
would prevent a sufficient intake of
air.
After each use a small quantity of
condensed water will collect in the area
around the pump. This water can run
out if the machine is tipped up when it
is being moved. It is a good idea to run
the Cool air programme for
approximately 1 minute before moving
the machine. Any remaining
condensed water will then be fed into
the condensed water container or out
through the drain hose.
31
Installation
External condensed water
outlet
From the back of the dryer at the
bottom:
When drying is in progress, condensed
water is pumped into the condensed
water container through the drain hose
at the back of the dryer. The
condensed water can also be drained
off directly if the machine is installed
near a sink, drain outlet etc. so that
the condensed water container does
not have to be emptied.
The drain hose (approx. 2 m long) is
stored in the dryer. It must be pulled
out of the dryer to its full extent if
condensed water is to be drained
externally. Maximum delivery head:
1.50 m.
If it is not long enough, an extension
hose is available as an optional
accessory through your dealer or from
the Miele Spare Parts Dept.
Setting up the drain hose
^ Unclip the drain hose from clip (3).
^ Then pull the drain hose completely
out of the dryer towards the left (4)
(See illustration). Important:
,Do not let the drain hose
become kinked, as this could
damage it.
From the back of the dryer at the top:
,If you want to drain the water off
into a sink you will need to secure
the hose carefully, e.g. by tying it to
a tap to make sure it cannot slip
during use. Otherwise there is a risk
of overflowing water which could
cause damage.
Use the bow-shaped guide to prevent
the drain hose from becoming kinked
(see "Front view" illustration).
^ Unclip the drain hose from clip (1).
^ Then pull it off holder (2).
32
Installation
Connection to a sink drain outlet
The drain hose can be connected
directly to a sink drain outlet.
If this nut has a flat disc in it you should
take the disc out first. Important: if this
nut has a washer or seal in it this must
not be removed!
^ Attach the end of the hose to
adapter 1.
^ Use a screwdriver to tighten hose
clip 3 up close to the nut.
If you no longer wish to use an
external condensed water outlet
,Do not push the drain hose
back into the dryer. Doing this could
cause it to become kinked and
damaged in the dryer.
^ Remove the following from the back
of the dryer at the bottom:
Adapter 1 and hose clip 3 behind it.
^ Loop the drain hose up.
^ Use a suitable cable tie to secure the
looped hose to the back of the dryer,
or simply lay the looped hose behind
the dryer.
^ Attach the open end of the drain
hose back onto the holder at the
back of the dryer at the top (see
holder 2 in "Setting up the drain
hose").
^ Fit adapter 1 to the sink drain outlet
using nut 2.
33
Electrical connection
Electrical connection U.K.
Non-rewireable plugs BS 1363
All electrical work should be carried out
by a suitably qualified and competent
person, in strict accordance with
current national and local safety
regulations (BS 7671 in the UK).
The fuse cover must be refitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words on the base of the
plug (as applicable to the design of
plug fitted).
Ensure power is not supplied to the
appliance until after installation work
has been carried out.
The appliance is supplied with a mains
cable with moulded plug ready for
connection to a 230-240V mains
supply. Please ensure the connection
data quoted on the data plate match
the household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible after installation.
For extra safety it is advisable to install
a residual current device (RCD), with a
trip current of 30 mA (in accordance
with DIN VDE 0664, VDE 0100 Section
739).
Do not connect via an extension lead.
Extension leads do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
34
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
WARNING: THIS APPLIANCE
MUST BE EARTHED
Consumption data
Programme
Load
Final spin speed
in a domestic washing machine
Energy
Time
kg*
rpm
kWh
Minutes
Cottons Normal
6.0
800 (70 % residual moisture)**
1200
1400
1600
1800
4.05
3.20
3.05
2.95
2.65
119
95
91
88
80
Cottons Hand iron
6.0
800 (70 % residual moisture)**
1200
1400
1600
1800
3.25
2.40
2.25
2.15
1.85
95
72
68
65
58
Minimum iron Normal
3.0
1000 (50 % residual moisture)**
1.50
54
Minimum iron Hand iron
3.0
1000
1.30
47
Automatic
3.0
900
1.95
109
Woollens handcare
2.0
900
0.15
4
Smoothing
3.0
-
0.30
9
* Weight of dry laundry
** EN 61121 test programme:
All data established in accordance with EN 61121.
Before testing in accordance with EN 61121, dry a 3 kg load of cotton laundry with 70% residual
moisture as per the above standard using the Cottons Normal programme.
Consumption data can vary from the nominal values given above depending on the size of the
load, types of textiles, residual moisture levels after spinning, fluctuations in the electricity
supply and any additional options selected.
35
Technical data
Height
850 mm (adjustable +7 / -7 mm)
Height for building under
820 mm
Width
Depth
595 mm
580 mm
Depth with door open
Weight
1,060 mm
54 kg
Drum volume
Maximum capacity
100 litres
6 kg dry weight
Capacity of condensed
water container
Hose length
approx. 3.5 l
2m
Maximum delivery head
Maximum drain hose length
1.50 m
4m
Length of connection cable
Voltage
2m
see data plate
Connected load
Fuse rating (UK)
see data plate
see plug
Lamp wattage
Energy consumption
see data plate
see "Consumption data" section
Test certificates awarded
Radio / TV suppression, VDE
36
Programmable functions
for changing default settings
The programmable functions are
used to alter the machine's
electronics to suit changing
requirements.
Programmable functions can be
altered at any time.
37
Programmable functions
Altering the residual moisture
level in the Cottons
programmes
The machine is designed to dry
effectively using as little energy as
possible.
However, if you require the laundry to
be drier, it is possible to reduce the
default residual moisture level in the
Cottons programmes.
Please note that programme
durations will be longer if this option
is activated.
Follow steps A to G to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
– The programme selector is at Finish.
A Press the Start button and keep it
pressed in whilst carrying out steps
B-C.
B Switch the dryer on with the
I-On/0-Off button.
C Wait until the Start indicator lamp
comes on . . .
D . . . and then release the Start button.
E Turn the programme selector to the
Cottons Normal position.
F Pressing the Start button switches
between activating and deactivating
the drier setting.
– If the Drying indicator lamp is
flashing: the drier setting is
activated
– If the Drying indicator lamp is not
flashing, the drier setting is not
activated and the residual moisture
level is on the standard default
setting.
G Switch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
To check:
^ Make sure the dryer is switched off,
the door is closed and the
programme selector is at Finish and
then carry out steps A to E.
The Drying indicator lamp will show you
if the drier setting has been selected.
^ Switch off the dryer.
The check is complete.
38
Programmable functions
Altering the residual moisture
level in the Minimum iron
programmes
The machine is designed to dry
effectively using as little energy as
possible.
However, if you require the laundry to
be drier, it is possible to reduce the
default residual moisture level in the
Minimum iron programmes.
Please note that programme
durations will be longer if this option
is activated.
Follow steps A to G to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
– The programme selector is at Finish.
A Press the Start button and keep it
pressed in whilst carrying out steps
B-C.
B Switch the dryer on with the
I-On/0-Off button.
C Wait until the Start indicator lamp
comes on . . .
D . . . and then release the Start button.
E Turn the programme selector to the
Cottons Low temperature position.
F Pressing the Start button switches
between activating and deactivating
the drier setting.
– If the Drying indicator lamp is
flashing, the drier setting is
activated
– If the Drying indicator lamp is not
flashing, the drier setting is not
activated and the residual moisture
level is on the standard default
setting.
G Switch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
To check:
^ Make sure the dryer is switched off,
the door is closed and the
programme selector is at Finish and
then carry out steps A to E.
The Drying indicator lamp will show you
if the drier setting has been selected.
^ Switch off the dryer.
The check is complete.
39
Programmable functions
Activating and deactivating the
buzzer
A buzzer sounds (at intervals for a
maximum of 1 hr) to let you know the
programme has finished.
The machine is delivered with the
buzzer activated but you can
deactivate it if wished.
The buzzer will still sound if there is a
fault, even if it has been deactivated.
Follow steps A to G to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
– The programme selector is at Finish.
A Press the Start button and keep it
pressed in whilst carrying out steps
B-C.
B Switch the dryer on with the
I-On/0-Off button.
C Wait until the Start indicator lamp
comes on . . .
D . . . and then release the Start button.
E Turn the programme selector to the
Cottons Hand iron position.
F Pressing the Start button switches
between activating and deactivating
the buzzer.
– If the Drying indicator lamp is not
flashing:
the buzzer is deactivated
– If the Drying indicator lamp is
flashing:
the buzzer is activated
G Switch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
To check:
^ Make sure the dryer is switched off,
the door is closed and the
programme selector is at Finish and
then carry out steps A to E.
The Drying indicator lamp will show you
if the buzzer is activated.
^ Switch off the dryer.
The check is complete.
40
Programmable functions
Extending the cooling down
time
The cooling down phase which takes
place before the end of a programme
can be lengthened if required. This
makes the garments easier to
handle.
The dryer is delivered with the
extended cooling down time option
deactivated. You can extend the
cooling down time by 5 minutes or 10
minutes.
The option of extending the cooling
down time is available with the Cottons,
Minimum iron and Automatic
programmes.
Follow steps A to G to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
– The programme selector is at Finish.
A Press the Start button and keep it
pressed in whilst carrying out steps
B-C.
– If the Drying indicator lamp flashes
once:
The cooling down time will be five
miinutes longer.
– If the Drying indicator lamp flashes
twice:
The cooling down time will be ten
minutes longer.
– If the Drying indicator lamp is not
flashing:
The cooling down time is not
extended.
G Switch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
To check:
^ Make sure the dryer is switched off,
the door is closed and the
programme selector is at Finish and
then carry out steps A to E.
The Drying indicator lamp will show you
if the cooling down time has been
extended.
^ Switch off the dryer.
The check is complete.
B Switch the dryer on with the
I-On/0-Off button.
C Wait until the Start indicator lamp
comes on . . .
D . . . and then release the Start button.
E Turn the programme selector to the
Cottons Machine iron position.
F Pressing the Start button alters the
cooling down time.
41
Programmable functions
Changing the standard drying
level in the Minimum iron Normal programme
The drying level for this programme
is set at a standard level.
You have the option of changing this
to an increased drying level.
The machine is delivered with the
drying level set at Normal
You can change this to Normal+ (drier
than the standard drying level).
Important: the "Normal+" drying level
will work in addition to the "Altering the
residual moisture level in the Minimum
iron programmes" programmable
function, if you have already set this.
F Pressing the Start button alters the
drying level.
– If the Drying indicator lamp is
flashing:
the standard drying level is
Normal+
– If the Drying indicator lamp is not
flashing, the increased drying level
is not activated and the drying level
will remain on the standard setting
(
).
G Switch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
To check:
Follow steps A to G to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
– The programme selector is at Finish.
A Press the Start button and keep it
pressed in whilst carrying out steps
B-C.
B Switch the dryer on with the
I-On/0-Off button.
C Wait until the Start indicator lamp
comes on . . .
D . . . and then release the Start button.
E Turn the programme selector to
Minimum iron - Normal.
42
^ Make sure the dryer is switched off,
the door is closed and the
programme selector is at Finish and
then carry out steps A to E.
The Drying indicator lamp will show you
if the Normal+ drying level has been
set.
^ Switch off the dryer.
The check is complete.
Programmable functions
Changing the standard drying
level in the Automatic
programme
The drying level for this programme
is set at a standard level.
You have the option of changing this
to an increased drying level.
The machine is delivered with the
drying level set at Normal
F Pressing the Start button alters the
drying level.
– If the Drying indicator lamp flashes
twice:
the standard drying level is
Normal+
– If the Drying indicator lamp is not
flashing:
the standard drying level is Hand
iron
You can change this to Hand iron
(damper) or Normal+ (drier than the
standard drying level).
– If the Drying indicator lamp flashes
once, the drying level has not been
changed and will remain on the standard setting (
).
Follow steps A to G to programme
and store in memory.
G Switch the machine off with the
I-On/0-Off button.
Before you begin, first ensure that:
The setting you have selected is now
stored in memory. You can change it
again at any time.
– The tumble dryer is switched off.
– The door is closed.
– The programme selector is at Finish.
To check:
A Press the Start button and keep it
pressed in whilst carrying out steps
B-C.
^ Make sure the dryer is switched off,
the door is closed and the
programme selector is at Finish and
then carry out steps A to E.
B Switch the dryer on with the
I-On/0-Off button.
The Drying indicator lamp will show you
if the drying level has been changed.
C Wait until the Start indicator lamp
comes on . . .
^ Switch off the dryer.
D . . . and then release the Start button.
The check is complete.
E Turn the programme selector to the
Automatic position.
43
Alteration rights reserved/0806
M.-Nr. 06 465 690 / 02
en - GB