Black & Decker Type 1 TRO4070B Instruction manual

ST4525
ST5530
A
B
C
D
E
F
2
G
H
I
J
K
L
3
M
4
N
(Original instructions)
Intended use
Your Black & Decker trimmer has been designed for trimming
and finishing lawn edges and to cut grass in confined spaces.
This appliance is intended for consumer use only.
Safety instructions
u
u
ENGLISH
Do not allow children or animals to
come near the work area or to touch
the appliance or power supply cord.
Close supervision is necessary when
the appliance is used near children.
This appliance is not intended for use
by young or infirm persons without
supervision.
This appliance is not to be used as a
toy.
Only use the appliance in daylight or
good artificial light.
Use in a dry location only. Do not allow
the appliance to become wet.
Do not immerse the appliance in water.
Do not open the body casing. There
are not user-serviceable parts inside.
Do not operate the appliance in
explosive atmospheres, such as in the
presence of flammable liquids, gases
or dust.
To reduce the risk of damage to plugs
or cords, never pull the cable to remove the plug from a socket.
Warning! When using mains-powered
appliances, basic safety precautions,
including the following, should always be
followed to reduce the risk of fire, electric
shock, personal injury and material damage.
Warning! When using the machine
the safety rules must be followed. For
your own safety and bystanders please
read these instructions before operating
the machine. Please keep the instructions safe for later use.
Read all of this manual carefully before
operating the appliance.
The intended use is described in this
manual. The use of any accessory
or attachment or the performance
of any operation with this appliance
other than those recommended in this
instruction manual may present a risk
of personal injury.
Safety of others
Retain this manual for future refer This appliance is not intended for use
ence.
by persons (including children) with
reduced physical, sensory or mental
Using your appliance
capabilities, or lack of experience
Always take care when using the appliand knowledge, unless they have
ance.
been given supervision or instruction
Always use safety glasses or goggles.
concerning use of the appliance by a
Never allow children or people unfaperson responsible for their safety.
miliar with the instructions to use the
Children must be supervised to ensure
appliance.
that they do not play with the appliance.
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
5
ENGLISH
(Original instructions)
Residual risks.
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged
use etc.
Even with the application of the relevant
safety regulations and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any
parts, blades or accessories.
Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods ensure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing
dust developed when using your tool
(example:- working with wood, especially oak, beech and MDF.)
u
u
Inspection and repairs
Before use, check the appliance for
damaged or defective parts. Check for
breakage of parts and any other conditions that may affect its operation.
Do not use the appliance if any part is
damaged or defective.
Have any damaged or defective parts
repaired or replaced by an authorised
repair agent.
Never attempt to remove or replace
any parts other than those specified in
this manual.
u
u
u
u
Additional safety instructions for grass trimmers
Warning! Cutting elements continue
to rotate after the motor is switched off.
Be familiar with the controls and the
proper use of the appliance.
Before use, check the power supply
cord and extension cord for signs of
damage, ageing and wear. If a cord
becomes damaged during use, disconAfter use
nect the cord from the mains supply
When not in use, the appliance should
immediately. DO NOT TOUCH THE
be stored in a dry, well ventilated place CORD BEFORE DISCONNECTING
out of reach of children.
THE SUPPLY.
Children should not have access to
Do not use the appliance if the cords
stored appliances.
are damaged or worn.
When the appliance is stored or trans Wear stout shoes or boots to protect
ported in a vehicle it should be placed
your feet.
in the boot or restrained to prevent
Wear long trousers to protect your
movement following sudden changes
legs.
in speed or direction.
Before using the appliance, check that
your cutting path is free from sticks,
stones, wire and any other obstacles.
u
u
u
u
u
u
u
u
u
u
u
u
6
(Original instructions)
u
u
ENGLISH
Only use the appliance in the upright
Take care against injury from any deposition, with the cutting line near the
vice fitted for trimming the filament line
ground. Never switch the appliance on
length. After extending new cutter line
in any other position.
always return the machine to its nor Move slowly when using the appliance.
mal operating position before switching
Be aware that freshly cut grass is
on.
damp and slippery.
Always ensure that the ventilation slots
Do not work on steep slopes. Work
are kept clear of debris.
across the face of slopes, not up and
Do not use the lawn trimmer (edge
down.
trimmer), if the cords are damaged or
Never cross gravel paths or roads
worn.
while the appliance is running.
Keep extension cords away from cut Never touch the cutting line while the
ting elements.
appliance is running.
Do not put the appliance down until the Electrical safety
cutting line has come to a complete
This appliance is double insu# lated; therefore no earth wire is
standstill.
Use only the appropriate type of cutrequired. Always check that the
ting line. Never use metal cutting line
power supply corresponds to the
or fishing line.
voltage on the rating plate.
Be careful not to touch the line trim If the supply cord is damaged, it must
ming blade.
be replaced by the manufacturer or
Take care to keep the mains cable
an authorised Black & Decker Service
away from the cutting line. Always be
Centre in order to avoid a hazard.
aware of the position of the cable.
Electric safety can be further improved
Keep hands and feet away from the
by using a highsensitivity 30 mA Recutting line at all times, especially
sidual Current Device (RCD).
when switching on the motor.
Before using the appliance and after
Labels on appliance
any impact, check for signs of wear or The following warning symbols are found on the appliance:
damage and repair as necessary.
Never operate the appliance with
Read the manual prior to operation.
damaged guards or without guards in
place.
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
u
Wear safety glasses or goggles when operating
this appliance.
7
ENGLISH
(Original instructions)
N
Wear suitable ear protectors when operating this
appliance.
K
Beware of flying objects. Keep bystanders away
from the cutting area.
E
R
Always remove the plug from the socket before
inspecting a damaged cable. Be careful not to
use your strimmer if the cable is damaged.
Do not expose the appliance to rain or high
humidity.
Directive 2000/14/EC guaranteed sound power.
Features
This appliance includes some or all of the following features.
1. On/off switch
2. Handle
3. Cable restraint
4. Power inlet
5. Second handle
6. Guard
7. Spool housing
8. Head
9. Edge wheel (ST5530 Only)
10. Edge guide (ST4525 Only)
Assembly
Adjusting the position of the secondary handle (fig.
D)
The second handle (5) can be adjusted to provide optimum
balance and comfort.
u Press in the button (14) on the left side of the handle.
u Rotate the second handle (5) into the required position.
u Release the button (14).
Warning! Ensure that the teeth on the button are correctly
aligned in slots in the handle and that the handle is secure.
Adjusting the height of the tool (fig. E)
This tool has a telescopic mechanism, allowing you to set it to
a comfortable height. There are multiple height settings.
To adjust the height setting, proceed as follows:
u Disconnect the tool from the supply.
u Loosen the adjustment collar (15) by turning it clockwise.
u Gently pull the tube (16) in or out of the handle (2) to the
desired height.
u Tighten the adjustment collar (15) by turning anti-clockwise.
Releasing the cutting line
In transit, the cutting line is taped to the spool housing.
Warning! Before assembly, disconnect from the power supply
u Remove the tape holding the cutting line to the spool
housing (7).
Connecting the tool to the mains (fig. F)
Connect the female plug of a suitable extension cable to
the power inlet (4).
u Loop the cable through the cable restraint (3).
u Insert the mains plug into a mains outlet.
For wired in cable units: Make sure the cable is looped
through the cable restraint prior to connecting the plug to the
mains outlet.
u
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Use
Fitting the guard (fig. A & B)
Setting the tool to trimming or edging mode (fig. G,
H, I & J)
Remove the screw from the guard.
u Keeping the guard (6) square to the strimmer head (8)
slide it into place until the retaining tab clicks into place
(Ensure that the guide rails (11) on the guard (6) are
correctly aligned with the guide rails (12) on the strimmer
head (8). fig. A).
u Secure the guard (6) with the screw (13).
Warning! Never use the tool unless the guard is properly
fitted.
u
Attaching the second handle (fig. C)
Press in and hold both of the buttons (14) on the side of
the handle.
u Slide the second handle (5) in place over the buttons (14).
Warning! Ensure that the teeth on the button are correctly
aligned in slots in the handle and that the handle is secure.
u
8
Warning! Let the tool work at its own pace. Do not overload.
The tool can be used in trimming mode as shown in fig. I or in
edging mode to trim overhanging grass along lawn edges and
flower beds as shown in fig. J.
Trimming mode (fig. E, G & I)
For trimming, the trimmer head should be in the position
shown in fig. I. If it is not:
u Disconnect the tool from the supply.
u Loosen the adjustment collar (15) by turning it clockwise.
u Whilst holding the handle (2), rotate the head (8) clockwise.
u Tighten the collar (15) by turning it anti-clockwise.
Note: Note: The head will only rotate in one direction.
(Original instructions)
Edging mode (fig. E, H & J)
For edging, the trimmer head should be in the position shown
in fig. J. If it is not:
u Disconnect the tool from the supply.
u Loosen the adjustment collar (15) by turning it clockwise.
u Whilst holding the handle (2), rotate the head (8) anticlockwise.
u Tighten the collar (15) by turning it anti-clockwise.
Note: The head will only rotate in one direction.
Switching on and off
To switch the tool on, squeeze the trigger lever (1).
To switch the tool off, release the trigger lever.
Warning! Never attempt to lock the trigger lever in the on
position.
u
u
Hints for optimum use
General
u
In order to achieve optimum cutting results, only cut dry
grass.
Trimming
Hold the tool as shown in fig. I.
Gently swing the trimmer from side to side.
u When cutting long grass, work in stages from the top. Take
small cuts.
u Keep the tool away from hard objects and delicate plants.
u Cutting line will wear faster and require more feeding if
the cutting is done along pavements or other abrasive
surfaces or heavier weeds are being cut.
u If the tool starts running slowly, reduce the load.
u
u
Edging
Optimum cutting results are achieved on edges deeper than
50 mm.
u Do not use the tool to create edges. To create edges,
use an edging spade.
u Guide the tool on its wheel (9) or edge guide (10) as
shown in fig. J.
u To make a closer cut, slightly tilt the tool.
Fitting a new spool of cutting line (fig. K)
Replacement spools of cutting line are available from your
Black & Decker dealer (cat. no. A6481).
u Unplug the tool.
u Keep the tabs (17) depressed and remove the spool cover
(18) from the spool housing (7).
u Remove the empty spool (19) from the spool housing.
u Remove any dirt and grass from the spool cover and
housing.
u Take the new spool and push it onto the boss in the spool
housing. Rotate the spool slightly until it is seated.
u Unclip the end of the cutting line and guide the line into
the eyelet (20). The line should protrude approx. 11 cm
from the spool housing.
ENGLISH
Align the tabs (17) on the spool cover with the cut outs
(21) in the spool housing.
u Push the cover onto the spool housing until it snaps
securely into place.
Warning! If the cutting lines protrude beyond the trimming
blade (22), cut them off so that they just reach the blade.
u
Winding new line onto an empty spool (fig. L, M &
N)
You may wind new cutting line onto an empty spool.
Replacement packs of cutting line are available from your
Black & Decker dealer (cat. no. A6170 (25 m), A6171 (40 m)).
u Remove the empty spool from the tool as described
above.
u Remove any remaining cutting line from the spool.
u Feed 2 cm of cutting line into the hole (23) in the spool as
shown (fig. L).
u Bend the cutting line and anchor it in the L-shaped slot
(24).
u Wind the cutting line onto the spool in the direction of the
arrow. Make sure to wind the line on neatly and in layers.
Do not criss-cross (fig. N).
u When the wound cutting line reaches the recesses (25),
cut the line. Let the line protrude approx. 11 cm from the
spool and hold a finger on the line to keep it in place (fig.
M).
u Proceed as described above to fit the spool on the tool.
Warning! Only use the appropriate type of Black & Decker
cutting line.
Troubleshooting
If your tool seems not to operate properly, follow the instructions below. If this does not solve the problem, please contact
your local Black & Decker repair agent.
Warning! Before proceeding, unplug the tool.
Appliance runs slowly
Check that the spool housing can rotate freely. Carefully
clean it if necessary.
u Check that the cutting line does not protrude more than
11 cm from the spool housing. If it does, cut it off so that it
just reaches the line trimming blade.
u
Automatic line feed does not work
Keep the tabs depressed and remove the spool cover
from the housing.
u Pull the cutting line until it protrudes 11 cm from the housing. If insufficient cutting line is left on the spool, install a
new spool of cutting line as instructed above.
u Align the tabs on the spool cover with the cut outs in the
housing.
u Push the cover onto the housing until it snaps securely
into place.
u If the cutting line protrudes beyond the trimming blade, cut
it off so that it just reaches the blade.
u
9
ENGLISH
(Original instructions)
If the automatic line feed still does not work or the
spool is jammed, try the following suggestions:
Carefully clean the spool cover and housing.
Remove the spool and check if the lever can move freely.
u Remove the spool and unwind the cutting line, then wind it
on neatly again as described above. Replace the spool as
instructed.
u
u
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at
the address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
at: www.2helpU.com
Technical data
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool/appliance care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your tool/appliance
and charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u Regularly clean the cutting line and spool using a soft
brush or dry cloth.
u Regularly use a blunt scraper to remove grass and dirt
from the underneath of the guard.
Protecting the environment
Z
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product available for separate collection.
z
Separate collection of used products and packaging allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
10
ST4525
ST5530
Type 1
Type 1
Input Voltage
V
230
230
Power Input
W
450
550
No-Load Speed
min
7300
7500
Weight
kg
2.5
2.5
AC
-1
Hand/arm weighted vibration value according to EN 786:
= 3.8 m/s , uncertainty (K) = 1.5 m/s .
2
L (sound preasure) 80 dB(A)
PA
uncertainty (K) = 1 dB(A)
2
(Original instructions)
EC declaration of conformity
MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
%
ST4525/ST5530
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 60335-1, EN 60335-2-91
2000/14/EC, Lawn Trimmer, L ≤ 50 cm, Annex VIII
DEKRA Certification B.V., Utrechtseweg 310,
6802 ED Arnhem, The Netherlands
Notified Body ID No.: 0344
Level of accoustic power according to 2000/14/EC
(Article 12, Annex III, L ≤ 50 cm):
L (measured sound power) 94 dB(A)
uncertainty (K) = 1 dB(A)
L (guaranteed sound power) 95 dB(A)
ENGLISH
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member
States of the European Union and the European Free Trade
Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair
wear and tear or replace such products to ensure minimum
inconvenience to the customer unless:
u The product has been used for trade, professional or hire
purposes;
u The product has been subjected to misuse or neglect;
u The product has sustained damage through foreign
objects, substances or accidents;
u Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
WA
WA
These products also comply with Directive 2004/108/EC and
2011/65/EU.
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Black & Decker.
_
Kevin Hewitt
Vice-President Global Engineering
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
27/09/2013
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black &
Decker repair agents and full details of our after-sales service
and contacts are available on the Internet at: www.2helpU.com
Please visit our website www.blackanddecker.co.uk to register
your new Black & Decker product and to be kept up to date
on new products and special offers. Further information on the
Black & Decker brand and our range of products is available
at www.blackanddecker.co.uk
Do not forget to register your product!
www.blackanddecker.co.uk/productregistration Register
your product online at www.blackanddecker.co.uk/productregistration or send your name,surname and product code
to Black & Decker in your country.
11
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark, Victoria, 3138
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Auckland 1060
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
90603204 REV-0
Tel. 03-8720 5100
Fax 03-9727 5940
Tel. +64 9 259 1133
Fax +64 9 259 1122
Tel. 01753 511234
Fax 01753 551155
09/2013