Makita BTM50 Instruction manual

ENGLISH (Original instructions)
INSTRUCTION MANUAL
Cordless Multi Tool
BTM40
BTM50
012764
IMPORTANT: Read Before Using.
1
ENGLISH (Original instructions)
SPECIFICATIONS
Model
BTM40
BTM50
Oscillation per minute
6,000 - 20,000 (min-1)
Oscillation angle, left/right
1.6 ゚ (3.2 ゚ total)
Overall length
324 mm
Standard battery cartridge
Net weight
BL1430
BL1415 *
BL1830
BL1815 *
without dust extraction attachment
1.9 kg
1.7 kg
2.0 kg
1.8 kg
with dust extraction attachment
2.0 kg
1.8 kg
2.1 kg
Rated voltage
D.C. 14.4 V
1.9 kg
D.C. 18 V
* NOTE: For continuous operation, high capacity battery cartridge BL1430 and BL1830 is recommended.
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
END221-2
Sound pressure level (LpA) : 78 dB(A)
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Work mode: Cutting with plunge cut saw blade
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
・ Read instruction manual.
Cd
Ni-MH
Li-ion
Model BTM40
・
Wear safety glasses.
・
Only for EU countries
Do not dispose of electric equipment or
battery pack together with household
waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment, 2006/66/EC on
batteries and accumulators and waste
batteries and accumulators and their
implementation in accordance with
national laws, electric equipment and
battery pack that have reached the end
of their life must be collected separately
and returned to an environmentally
compatible recycling facility.
Sound pressure level (LpA) : 82 dB(A)
Sound power level (LWA) : 93 dB(A)
Uncertainty (K) : 3 dB(A)
Model BTM50
Sound pressure level (LpA) : 84 dB(A)
Sound power level (LWA) : 95 dB(A)
Uncertainty (K) : 3 dB(A)
Work mode: Cutting with segmental saw blade
Sound pressure level (LpA) : 81 dB(A)
Sound power level (LWA) : 92 dB(A)
Uncertainty (K) : 3 dB(A)
Work mode: Scraping
Model BTM40
ENE080-1
Sound pressure level (LpA) : 81 dB(A)
Sound power level (LWA) : 92 dB(A)
Uncertainty (K) : 3 dB(A)
Intended use
The tool is intended for sawing and cutting wood, plastic,
gypsum, non-ferrous metals, and fastening elements (e.
g. unhardened nails and staples). It is also intended for
working soft wall tiles, as well as dry sanding and
scraping of small surfaces. It is especially for working
close to edge and flush cutting.
Model BTM50
Sound pressure level (LpA) : 83 dB(A)
Sound power level (LWA) : 94 dB(A)
Uncertainty (K) : 3 dB(A)
ENG905-1
Wear ear protection
Noise
The typical A-weighted noise level determined according
to EN60745:
Work mode: Sanding
2
ENG900-1
ENH101-15
For European countries only
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode: Sanding
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Cordless Multi Tool
Model No./ Type: BTM40, BTM50
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
Vibration emission (ah) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s2
Work mode: Cutting with plunge cut saw blade
Model BTM40
Vibration emission (ah) : 9.5 m/s2
Uncertainty (K) : 1.5 m/s2
Model BTM50
Vibration emission (ah) : 10.0 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: Cutting with segmental saw blade
Model BTM40
Vibration emission (ah) : 5.0 m/s2
Uncertainty (K) : 1.5 m/s2
20.10.2011
Model BTM50
Vibration emission (ah) : 5.5 m/s2
Uncertainty (K) : 1.5 m/s2
Work mode: Scraping
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
Model BTM40
Vibration emission (ah) : 7.5 m/s2
Uncertainty (K) : 1.5 m/s2
GEA006-2
Model BTM50
General Power Tool Safety
Warnings
Vibration emission (ah) : 9.5 m/s2
Uncertainty (K) : 1.5 m/s2
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
ENG901-1
•
•
•
•
The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
WARNING:
The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
3
15.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
16. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
Power tool use and care
17. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
19. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
20. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
21. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
Battery tool use and care
24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
25. Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
26. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
3.
Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an
GFCI reduces the risk of electric shock.
Personal safety
10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
12. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
4
10.
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery
terminals together may cause burns or a fire.
27. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may
cause irritation or burns.
Service
28. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
29. Follow instruction for lubricating and
changing accessories.
30. Keep handles dry, clean and free from oil and
grease.
11.
12.
13.
14.
15.
16.
GEB094-2
17.
CORDLESS MULTI TOOL
SAFETY WARNINGS
1.
2.
3.
4.
5.
6.
7.
8.
9.
This power tool is intended to function for
sawing, cutting, grinding and sanding. Read
all safety warnings, instructions, illustrations
and specifications provided with this power
tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious
injury.
Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring. Cutting accessory contacting a
"live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
Always use safety glasses or goggles.
Ordinary eye or sun glasses are NOT safety
glasses.
Avoid cutting nails. Inspect workpiece for any
nails and remove them before operation.
Hold the tool firmly.
Make sure the application tool is not
contacting the workpiece before the switch is
turned on.
Keep hands away from moving parts.
Do not leave the tool running. Operate the tool
only when hand-held.
18.
19.
20.
21.
22.
5
Always switch off and wait for the blade to
come to a complete stop before removing the
blade from the workpiece.
Do not touch the application tool or the
workpiece immediately after operation; they
may be extremely hot and could burn your
skin.
Do not operate the tool at no-load
unnecessarily.
Always use the correct dust mask/respirator
for the material and application you are
working with.
Some material contains chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
supplier safety data.
This tool has not been waterproofed, so do not
use water on the workpiece surface.
Ventilate your work area adequately when you
perform sanding operations.
Use of this tool to sand some products, paints
and wood could expose user to dust
containing hazardous substances. Use
appropriate respiratory protection.
Be sure that there are no cracks or breakage
on the pad before use. Cracks or breakage
may cause a personal injury.
Do not use accessories which are not
specifically designed and recommended by
the tool manufacturer. Just because the
accessory can be attached to your power tool, it
does not assure safe operation.
Wear
personal
protective
equipment.
Depending on application, use face shield,
safety goggles or safety glasses. As
appropriate, wear hearing protectors, gloves
and workshop apron capable of stopping
small abrasive or workpiece fragments. The
eye protection must be capable of stopping flying
debris generated by various operations . The dust
mask or respirator must be capable of filtrating
particles generated by your operation. Prolonged
exposure to high intensity noise may cause
hearing loss.
Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of workpiece or of a broken accessory
may fly away and cause injury beyond immediate
area of operation.
Never lay the power tool down until the
accessory has come to a complete stop. The
spinning accessory may grab the surface and pull
the power tool out of your control.
23.
24.
25.
26.
27.
Do not run the power tool while carrying it at
your side. Accidental contact with the accessory
could snag your clothing, pulling the accessory
into your body.
Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
Do not use accessories that require liquid
coolants. Using water or other liquid coolants may
result in electrocution or shock.
Always be sure that the tool is switched off
and unplugged or that the battery cartridge is
removed before carrying out any work on the
tool.
Always be sure you have a firm footing. Be
sure no one is below when using the tool in
high locations.
6.
7.
8.
9.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
SAVE THESE INSTRUCTIONS.
WARNING:
2.
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
3.
ENC007-7
4.
IMPORTANT SAFETY
INSTRUCTIONS
FOR BATTERY CARTRIDGE
1.
2.
3.
4.
5.
A battery short can cause a large current flow,
overheating, possible burns and even a
breakdown.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 ゚ C (122 ゚ F).
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Do not use a damaged battery.
Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
Do not disassemble battery cartridge.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
6
Charge
the
battery
cartridge
before
completely discharged.
Always stop tool operation and charge the
battery cartridge when you notice less tool
power.
Never recharge a fully charged battery
cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room
temperature at 10 ゚ C - 40 ゚ C (50 ゚ F - 104 ゚ F).
Let a hot battery cartridge cool down before
charging it.
Charge the battery cartridge once in every six
months if you do not use it for a long period of
time.
Battery protection system
(Lithium-ion battery with star marking)
FUNCTIONAL DESCRIPTION
•
WARNING:
Always be sure that the tool is switched off and
battery cartridge is removed before adjusting
or checking function on the tool. Failure to
switch off and remove the battery cartridge may
result in serious personal injury from accidental
start-up.
1. Star marking
1
Installing or removing battery cartridge
012128
Lithium-ion batteries with a star marking are equipped
with a protection system. This system automatically cuts
off power to the tool to extend battery life.
The tool will automatically stop during operation if the tool
and/or battery are placed under one of the following
conditions:
•
Overloaded:
The tool is operated in a manner that causes
it to draw an abnormally high current.
In this situation, slide the slide switch on the
tool toward the "O (OFF)" position and stop
the application that caused the tool to become
overloaded. Then slide the slide switch
toward the "I (ON)" position again to restart.
If the tool does not start, the battery is
overheated. In this situation, let the battery
cool before sliding the slide switch toward the
"I (ON)" position again.
•
Low battery voltage:
The remaining battery capacity is too low and
the tool will not operate. In this situation,
remove and recharge the battery.
1. Button
2. Red indicator
3. Battery
cartridge
1
2
3
012765
CAUTION:
Always switch off the tool before installing or
removing of the battery cartridge.
•
Hold the tool and the battery cartridge firmly
when installing or removing battery cartridge.
Failure to hold the tool and the battery cartridge
firmly may cause them to slip off your hands and
result in damage to the tool and battery cartridge
and a personal injury.
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip it
into place. Insert it all the way until it locks in place with a
little click. If you can see the red indicator on the upper
side of the button, it is not locked completely.
•
•
•
Switch action
1
CAUTION:
Always install the battery cartridge fully until the red
indicator cannot be seen. If not, it may accidentally
fall out of the tool, causing injury to you or someone
around you.
Do not install the battery cartridge forcibly. If the
cartridge does not slide in easily, it is not being
inserted correctly.
1. Slide switch
012768
CAUTION:
Before installing the battery cartridge into the tool,
always check to see that the tool is switched off.
To start the tool, slide the slide switch toward the "I (ON)"
position.
To stop the tool, slide the slide switch toward the "O
(OFF)" position.
•
7
Adjusting the orbital stroke rate
Indication lamp
1. Dial
1. Indication lamp
1
1
012770
012771
The orbital stroke rate is adjustable. To change the orbital
stroke rate, turn the dial between 1 and 6. The higher the
number is, the higher the orbital stroke rate is. Preset the
dial to the number suitable for your workpiece.
When the remaining battery capacity gets low, the
indication lamp blinks.
•
When the remaining battery capacity gets much
lower, the tool stops during operation and the
indication lamp lights up about 10 seconds.
At this time, remove the battery cartridge from the tool
and charge it.
•
NOTE:
•
The dial cannot be turned directly from 1 to 6 or
from 6 to 1. Forcing the dial may damage the tool.
When changing the dial direction, always turn the
dial moving it through each intermediate number.
ASSEMBLY
Lighting up the front lamp
•
•
WARNING:
Never look into the light directly. Direct light causes
damage to your eyes.
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out
any work on the tool.
Installing or removing application tool
(optional accessory)
1. Front lamp
1
•
•
012779
Slide the slide switch toward the "I (ON)" position to light
up the front lamp. The lamp keeps on lighting while the
switch is the "I (ON)" position. The light automatically
goes out after pressing the rear of the slide switch, and
then sliding the slide switch toward the "O (OFF)"
position.
Overload protection
When the tool is overloaded and the tool temperature
reaches a certain level, the front lamp blinks and the tool
automatically stops. Remove a cause of overload to
restart.
WARNING:
Do not install application tool upside down.
Installing application tool upside down may damage
the tool and cause serious personal injury.
Install attachment tool in the correct direction
according to your work. Application tool can be
installed at an angle of every 30 degree.
2
1
3
012826
8
1. Application tool
installation bolt
2. Holes in the
application tool
3. Protrusions of
the tool flange
OPERATION
1. Application tool
installation bolt
2. Hex wrench
3. Tighten
2
1
•
WARNING:
Before starting the tool and during operation, keep
your hand and face away from the application tool.
•
CAUTION:
Do not apply excessive load to the tool which may
cause a motor lock and stop the tool.
3
012767
Cutting, sawing and scraping
Put an application tool (optional accessory) on the tool
flange so that the protrusions of the tool flange fit in the
holes in the application tool and secure the application
tool by tightening the bolt firmly with the hex wrench.
When using sanding application tool, mount the
application tool on the sanding pad so that it matches the
sanding pad direction.
The sanding pad has a hook and loop type fitting system
which allows easy and rapid fitting of a sanding paper.
As sanding papers have holes for dust extraction, mount
a sanding paper so that the holes in a sanding paper
match those in the sanding pad.
To remove a sanding paper, raise its end and peel it off.
Loosen and remove the application tool installation bolt
using a hex wrench and then take off the application tool.
•
CAUTION:
Do not move on the tool forcibly in the direction (eg.
towards either side) of tool application with no
cutting edge. It may damage the tool.
012801
Put the application tool on the workpiece.
And then move the tool forward so that the application
tool movement does not slow down.
1. Application tool
installation bolt
2. Holes in the
application tool
3. Adapter (required
for some
application tools)
4. Protrusions of
the tool flange
1
2
3
4
NOTE:
•
Forcing or excessive pressure on the tool may
reduce efficiency.
•
Before cutting operation, it is recommended to
preset the orbital stroke rate 4 - 6.
012847
When using application tools with a different type of
installation section, use a correct adapter (optional
accessory).
Sanding
Hex wrench storage
•
1. Hex wrench
•
1
CAUTION:
Do not reuse a sanding paper used for sanding
metal to sand wood.
Do not use a worn sanding paper or sanding paper
without grit.
012766
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.
012769
Apply a sanding paper on the workpiece.
9
NOTE:
•
Using a test material sample to try is
recommendable to determine a correct orbital
stroke rate suitable for your work.
•
Use a sanding paper with the same grit until
sanding the whole workpiece is completed.
Replacing a sanding paper with different grit
sanding paper may not get a fine finish.
Dust extraction attachment
(optional accessory)
1
012800
When you wish to perform cleaner operation, connect a
vacuum cleaner to your tool. Connect a hose of vacuum
cleaner to the dust extraction attachment (optional
accessory).
9
MAINTENANCE
8
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
•
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may
result.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
•
5
2
3
6
4
7
1. Nozzle band
2. Dust nozzle
3. Dust nozzle
4. Dust attachment
5. Felt ring
6. Pad
7. Application tool installation bolt
8. Holes in the tool
9. Protrusions on the nozzle band
OPTIONAL ACCESSORIES
CAUTION:
These
accessories
or
attachments
are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
Segment saw blade
•
Round saw blade
•
Plunge cut saw blade
•
Scraper (rigid)
•
Scraper (flexible)
•
Serrated seg blade
•
General joint cutter
•
HM remover
•
HM seg saw blade
•
012778
•
•
•
Install dust nozzles and dust attachment.
Install the nozzle band on the tool so that its
protrusions fit in the holes in the tool to secure it.
Put the felt ring and the sanding pad on the dust
attachment and then secure them with the
application tool installation bolt.
10
•
•
•
•
•
•
•
•
•
•
HM sanding plate
Diamond seg sawblade
Sanding pad
Adapter
Abrasive paper delta (red / white / black)
Fleece delta (medium / coarse / without grit)
Polishing felt delta
Hex wrench
Dust extraction attachment
Makita genuine battery and charger
NOTE:
•
Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
11
Makita Corporation
Anjo, Aichi, Japan
885117A224
12
www.makita.com