Wizard WA20H42STA Product specifications

For Parts Call K&T 606-678-9623 or 606-561-4983
MODEL NO. WA20H42STA
20.0 HP 42 INCH
LAWN TRACTOR
For Parts and Service, contact our authorized distributor:
call 1-800-849-1297 For Technical Assistance: call 1-800-829-5886
00273
185106 Rev. 3 03.21.03 TR/MH/TR
PRINTED IN U.S.A.
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TABLE OF CONTENTS
Maintenance ....................................... 18
Maintenance Schedule ........................ 18
Service and Adjustments..................... 22
Storage ................................................ 27
Troubleshooting ................................... 28
Repair Parts......................................... 32
Warranty ................................................ 2
Safety Rules .......................................... 3
Product Specifications ........................... 6
Assembly/Pre-Operation ....................... 8
Operation............................................. 11
WARRANTY
LIMITED WARRANTY
The Manufacturer warrants to the original consumer purchaser that this product as
manufactured is free from defects in materials and workmanship. For a period of two
(2) years from date of purchase by the original consumer purchaser, we will repair or
replace, at our option, without charge for parts or labor incurred in replacing parts, any
part which we find to be defective due to materials or workmanship. This Warranty is
subject to the following limitations and exclusions.
1. This warranty does not apply to the engine, other than EHP manufactured transaxle/
transmission components, battery (except as noted below) or components parts
thereof. Please refer to the applicable manufacturer's warranty on these items.
2. Transportation charges for the movement of any power equipment unit or attachment
are the responsibility of the purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by the purchaser unless such
return is requested by Electrolux Home Products.
3. Battery Warranty: On products equipped with a Battery, we will replace, without
charge to you, any battery which we find to be defective in manufacture, during the
first ninety (90) days of ownership. After ninety (90) days, we will exchange the Battery, charging you 1/12 of the price of a new Battery for each full month from the date
of the original sale. Battery must be maintained in accordance with the instructions
furnished.
4. The Warranty period for any products used for rental or commercial purposes is
limited to 90 days from the date of original purchase.
5. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained in accordance with the instructions furnished. This
Warranty does not apply to any product which has been subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of
the product.
6. Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal
wear, normal adjustments, standard hardware and normal maintenance.
7. In the event you have a claim under this Warranty, you must return the product to an
authorized service dealer.
Should you have any unanswered questions concerning this Warranty, please contact:
In Canada contact:
Electrolux Canada Corp.
7075 Ordan Drive
Mississauga, Ontario
L5T 1K6
Electrolux Home Products, Inc.
Outdoor Products Customer Service Dept.
250 Bobby Jones Expressway
Augusta, GA 30909 USA
giving the model number, serial number and date of purchase of your product and the
name and address of the authorized dealer from whom it was purchased.
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL
DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME
PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas do
not allow the limitation of consequential damages or limitations of how long an implied
Warranty may last, so the above limitations or exclusions may not apply to you. This
Warranty gives you specific legal rights, and you may have other rights which vary from
locale to locale.
This is a limited Warranty within the meaning of that term as defined in the MagnusonMoss Act of 1975.
2
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
SAFETY RULES
IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious
injury or death.
place.
WARNING: In order to prevent ac•
Slow down before turning.
cidental starting when setting up, trans•
Never leave a running machine unatporting, adjusting or making repairs,
tended.
Always turn off blades, set
always disconnect spark plug wire and
parking
brake,
stop engine, and remove
place wire where it cannot contact spark
keys
before
dismounting.
plug.
• Turn off blades when not mowing.
WARNING: Do not coast down a hill in
• Stop engine before removing grass
neutral, you may lose control of the tractor.
catcher or unclogging chute.
WARNING: Tow only the attachments
• Mow only in daylight or good artificial
that are recommended by and comply with
light.
specifications of the manufacturer of your
• Do not operate the machine while under
tractor. Use common sense when towing.
the influence of alcohol or drugs.
Operate only at the lowest possible speed
• Watch for traffic when operating near or
when on a slope. Too heavy of a load,
crossing roadways.
while on a slope, is dangerous. Tires can
• Use extra care when loading or unlose traction with the ground and cause
loading the machine into a trailer or
you to lose control of your tractor.
truck.
•
Data indicates that operators, age 60
WARNING: Engine exhaust, some
years
and above, are involved in a large
of its constituents, and certain vehicle
percentage
of riding mower-related incomponents contain or emit chemicals
juries.
These
operators should evaluate
known to the State of California to cause
their
ability
to
operate
the riding mower
cancer and birth defects or other reproducsafely
enough
to
protect
themselves and
tive harm.
others from serious injury.
WARNING: Battery posts, terminals
• Keep machine free of grass , leaves or
and related accessories contain lead and
other debris build-up which can touch
lead compounds, chemicals known to the
hot exhaust / engine parts and burn . Do
State of California to cause cancer and
not allow the mower deck to plow leaves
birth defects or other reproductive harm.
or other debris which can cause buildWash hands after handling.
up to occur. Clean any oil or fuel
spillage before operating or storing the
I. GENERAL OPERATION
machine . Allow machine to cool before
• Read, understand, and follow all instrucstorage.
tions in the manual and on the machine
before starting.
II. SLOPE OPERATION
• Only allow responsible adults, who are
Slopes are a major factor related to lossfamiliar with the instructions, to operate
of-control and tipover accidents, which can
the machine.
• Clear the area of objects such as rocks, result in severe injury or death. All slopes
require extra caution. If you cannot back
toys, wire, etc., which could be picked
up the slope or if you feel uneasy on it, do
up and thrown by the blade.
• Be sure the area is clear of other people not mow it.
before mowing. Stop machine if anyone DO:
• Mow up and down slopes, not across.
enters the area.
• Remove obstacles such as rocks, tree
• Never carry passengers.
limbs, etc.
• Do not mow in reverse unless absolutely necessary. Always look down and • Watch for holes, ruts, or bumps. Uneven terrain could overturn the machine.
behind before and while backing.
Tall grass can hide obstacles.
• Be aware of the mower discharge direc• Use slow speed. Choose a low gear
tion and do not point it at anyone. Do
so that you will not have to stop or shift
not operate the mower without either
while on the slope.
the entire grass catcher or the guard in
3
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
SAFETY RULES
• Follow the manufacturer’s recommendations for wheel weights or counterweights to improve stability.
• Use extra care with grass catchers or
other attachments. These can change
the stability of the machine.
• Keep all movement on the slopes slow
and gradual. Do not make sudden
changes in speed or direction.
• Avoid starting or stopping on a slope. If
tires lose traction, disengage the blades
and proceed slowly straight down the
slope.
DO NOT:
• Do not turn on slopes unless necessary, and then, turn slowly and gradually
downhill, if possible.
• Do not mow near drop-offs, ditches,
or embankments. The mower could
suddenly turn over if a wheel is over
the edge of a cliff or ditch, or if an edge
caves in.
• Do not mow on wet grass. Reduced
traction could cause sliding.
• Do not try to stabilize the machine by
putting your foot on the ground.
• Do not use grass catcher on steep
slopes.
IV. SERVICE
• Use extra care in handling gasoline and
other fuels. They are flammable and
vapors are explosive.
- Use only an approved container.
- Never remove gas cap or add fuel
with the engine running. Allow
engine to cool before refueling. Do
not smoke.
- Never refuel the machine indoors.
- Never store the machine or fuel
container inside where there is an
open flame, such as a water heater.
• Never run a machine inside a closed
area.
• Keep nuts and bolts, especially blade
attachment bolts, tight and keep equipment in good condition.
• Never tamper with safety devices.
Check their proper operation regularly.
• Keep machine free of grass, leaves, or
other debris build-up. Clean oil or fuel
spillage. Allow machine to cool before
storing.
• Stop and inspect the equipment if you
strike an object. Repair, if necessary,
before restarting.
• Never make adjustments or repairs with
the engine running.
• Grass catcher components are subject
to wear, damage, and deterioration,
which could expose moving parts or
allow objects to be thrown. Frequently
check components and replace with
manufacturer's recommended parts,
when necessary.
• Mower blades are sharp and can cut.
Wrap the blade(s) or wear gloves, and
use extra caution when servicing them.
• Check brake operation frequently. Adjust and service as required.
III. CHILDREN
Tragic accidents can occur if the operator
is not alert to the presence of children.
Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you
last saw them.
• Keep children out of the mowing area
and under the watchful care of another
responsible adult.
• Be alert and turn machine off if children
enter the area.
• Before and when backing, look behind
and down for small children.
• Never carry children. They may fall off
and be seriously injured or interfere with
safe machine operation.
• Never allow children to operate the
machine.
• Use extra care when approaching blind
corners, shrubs, trees, or other objects
that may obscure vision.
4
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
SAFETY RULES
• Remove obstacles such as rocks, tree
limbs, etc.
• Watch for holes, ruts, or bumps. Uneven
terrain could overturn the machine. Tall
grass can hide obstacles.
• Use slow speed. Choose a low gear
so that you will not have to stop or shift
while on the slope.
• Avoid starting or stopping on a slope. If
tires lose traction, disengage the blades
and proceed slowly straight down the
slope.
• If machine stops while going uphill,
disengage blades, shift into reverse and
back down slowly.
• Do not turn on slopes unless necessary,
and then, turn slowly and gradually
downhill, if possible.
• Be sure the area is clear of other people
before mowing. Stop machine if anyone
enters the area.
• Never carry passengers or children
even with the blades off.
• Do not mow in reverse unless absolutely necessary. Always look down and
behind before and while backing.
• Never carry children. They may fall off
and be seriously injured or interfere with
safe machine operation.
• Keep children out of the mowing area
and under the watchful care of another
responsible adult.
• Be alert and turn machine off if children
enter the area.
• Before and when backing, look behind
and down for small children.
• Mow up and down slopes (15° Max), not
across.
5
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
PRODUCT SPECIFICATIONS
Gasoline
Capacity
and Type:
Oil Type
(API-SF-SJ):
Oil Capacity:
Spark Plug:
(GAP: .030")
Ground Speed
(MPH):
Tire Pressure:
Charging
System:
Battery:
Blade Bolt
Torque:
CUSTOMER RESPONSIBILITIES
• Read and observe the safety rules.
• Follow a regular schedule in maintaining, caring for and using your tractor.
• Follow the instructions under “Maintenance” and “Storage” sections of this
owner’s manual.
WARNING: This tractor is equipped
with an internal combustion engine and
should not be used on or near any unimproved forest-covered, brush-covered or
grass-covered land unless the engine’s
exhaust system is equipped with a spark
arrester meeting applicable local or state
laws (if any). If a spark arrester is used, it
should be maintained in effective working
order by the operator.
In the state of California the above is
required by law (Section 4442 of the
California Public Resources Code). Other
states may have similar laws. Federal
laws apply on federal lands. A spark arrester for the muffler is available through
your nearest authorized service center/department (See REPAIR PARTS section of
this manual).
2.0 Gallons
Unleaded
Regular
SAE 30 (Above 32°F)
SAE 5W-30
(Below 32°F)
4.0 Pints
Champion QC12YC
Forward:
Reverse:
5.5
2.4
Front: 14 PSI
Rear: 10 PSI
3 Amps Battery
5 Amps Headlights
Amp/Hr:
35
Min. CCA: 280
Case Size: U1R
27–35 Ft. Lbs.
CONGRATULATIONS on your purchase
of a new tractor. It has been designed,
engineered and manufactured to give
you the best possible dependability and
performance.
Should you experience any problem you
cannot easily remedy, please contact
your nearest authorized service center/
department . We have competent, welltrained technicians and the proper tools to
service or repair this tractor.
Please read and retain this manual. The
instructions will enable you to assemble
and maintain your tractor properly. Always
observe the “SAFETY RULES”.
6
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
UNASSEMBLED PARTS
Steering Wheel
Steering
Wheel
Adapter
Steering
Sleeve
(1) Large Flat
Washer
Steering
Extension
Shaft
Steering
Wheel
Insert
(1) Locknut 1/2-20
(1) Hex Bolt 1/4-28 x 1-1/4 (1) Locknut
1/4-28
Seat
(1) Washer
17/32 x 1-3/16 x 12 Gauge
(1) Knob
Mower
(2) Mulch Blades
Slope Sheet
Keys
(1) Oil Drain Tube
For Future Use
(2) Keys
7
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
ASSEMBLY/PRE-OPERATION
Your new tractor has been assembled at the factory with the exception of those parts left
unassembled for shipping purposes. To ensure safe and proper operation of your tractor
all parts and hardware you assemble must be tightened securely. Use the correct tools
as necessary to insure proper tightness. Review the video cassette before you begin.
TOOLS REQUIRED FOR ASSEMBLY
Insert
A socket wrench set will make assembly
easier. Standard wrench sizes you need
are listed below.
(1) 3/4" wrench
(1) Pliers
(2) 7/16" wrench
(1) Utility knife
(1) Tire pressure gauge
When right or left hand is mentioned in this
manual, it means, from your point of view,
when you are in the operating position
(seated behind the steering wheel).
1/2 Hex Nut
Large Flat Washer
Steering
Wheel
Steering Boot
Tabs
TO REMOVE TRACTOR FROM
CARTON
UNPACK CARTON
1. Remove all accessible loose parts and
parts boxes from carton.
2. Cut, from top to bottom, along lines
on all four corners of carton, and lay
panels flat.
3. Check for any additional loose parts or
cartons and remove.
Adapter
Extension Shaft
1/4 Locknut
1/4 Hex Bolt
Lower
Steering
Shaft
BEFORE REMOVING TRACTOR
FROM SKID
ATTACH STEERING WHEEL
ASSEMBLE EXTENSION SHAFT AND
BOOT
1. Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4
hex bolt and locknut. Tighten securely.
IMPORTANT: Tighten bolt and nut securely to 10-12 ft. lbs torque.
2. Place tabs of steering boot over tab
slots in dash and push down to secure.
Tab
Slots
IMPORTANT: Check for and remove any
staples in skid that may puncture tires
where tractor is to roll off skid.
INSTALL SEAT
Adjust seat before tightening adjustment
knob.
1. Remove adjustment knob and flat
washer securing seat to cardboard
packing and set aside for assembly of
seat to tractor.
2. Pivot seat upward and remove from
the cardboard packing. Remove the
cardboard packing and discard.
3. Place seat on seat pan so head of
shoulder bolt is positioned over large
slotted hole in pan.
4. Push down on seat to engage shoulder
bolt in slot and pull seat towards rear of
tractor.
5. Pivot seat and pan forward and assemble adjustment knob and flat
washer loosely. Do not tighten.
6. Lower seat into operating position and
sit in seat.
INSTALL STEERING WHEEL
3. Position front wheels of the tractor so
they are pointing straight forward.
4. Remove steering wheel adapter from
steering wheel and slide adapter onto
steering shaft extension.
5. Position steering wheel so cross bars
are horizontal (left to right) and slide
inside boot and onto adapter.
6. Assemble large flat washer, 1/2 hex
nut and tighten securely.
7. Snap steering wheel insert into center
of steering wheel.
8. Remove protective materials from tractor hood and grill.
8
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
7. Slide seat until a comfortable position
is reached which allows you to press
clutch/brake pedal all the way down.
8. Get off seat without moving its adjusted position.
9. Raise seat and tighten adjustment
knob securely.
4. Roll tractor forward off skid.
5. Remove banding holding deflector
shield up against tractor.
TO DRIVE TRACTOR OFF SKID (See
Operation section for location and
function of controls)
WARNING: Before starting, read, understand and follow all instructions in the
Operation section of this manual. Be sure
tractor is in a well-ventilated area. Be sure
the area in front of tractor is clear of other
people and objects.
1. Be sure all the above assembly steps
have been completed.
2. Check engine oil level and fill fuel tank
with gasoline.
3. Place freewheel control in "transmission engaged" position. (See “TO
TRANSPORT” in the Operation section
of this manual).
4. Sit on seat in operating position,
depress clutch/brake pedal and set the
parking brake.
5. Place motion control lever in neutral
(N) position.
6. Press lift lever plunger and raise
attachment lift lever to its highest position.
7. Start the engine. After engine has
started, move throttle control to idle
position.
8. Release parking brake.
9. Slowly move the motion control lever
forward and slowly drive tractor off
skid.
10. Apply brake to stop tractor, set parking
brake and place motion control lever in
neutral position.
11. Turn ignition key to "STOP" position.
Continue with the instructions that follow.
Seat
Seat Pan
Shoulder
Bolt
02466
Flat Washer
Adjustment Knob
02464
CHECK BATTERY
1. Lift seat pan to raised position.
NOTE: If this battery is put into service
after month and year indicated on label
(label located between terminals) charge
battery for minimum of one hour at 6-10
amps. (See "BATTERY" in Maintenance
section of this manual for charging instructions).
Seat pan
Label
Terminal
IMPORTANT: For shipping purposes, the
mulcher plate was preattached to your
mower. The mulcher plate must only be
used with the mulching blades that came
packed separately in the carton.
Your mower came factory equipped with
high performance blades, which are the
best blades for bagging and discharging.
To use your mower with the high performance blades the mulcher plate must be
removed from the mower.
Terminal
NOTE: You may now roll or drive your
tractor off the skid. Follow the appropriate
instruction below to remove the tractor
from the skid.
TO ROLL TRACTOR OFF SKID (See
Operation section for location and
function of controls)
1. Press lift lever plunger and raise
attachment lift lever to its highest position.
2. Release parking brake by depressing
clutch/brake pedal.
3. Place freewheel control in “transmission disengaged” position (See “TO
TRANSPORT” in the Operation section
of this manual).
TO SET UP YOUR MOWER FOR
MULCHING
• Remove high performance blades and
install mulching blades, (see BLADE
REMOVAL in the Maintenance section
of this manual).
9
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
INSTALL MULCHER PLATE
NOTE: If you installed the mulching blades
you will need to install the mulcher plate.
1. Raise and hold deflector shield in
upright position.
2. Place front of mulcher plate over front
of mower deck opening and slide into
place, as shown.
3. Hook front latch into hole on front of
mower deck.
4. Hook rear latch into hole on back of
mower deck.
CAUTION: Do not remove deflector
shield from mower.
CHECK FOR PROPER POSITION
OF ALL BELTS
TO CONVERT TO BAGGING OR
DISCHARGING
Before you operate your new tractor, we
wish to assure that you receive the best
performance and satisfaction from this
quality product.
Please review the following checklist:
✓ All assembly instructions have been
completed.
✓ No remaining loose parts in carton.
✓ Battery is properly prepared and
charged. (Minimum 1 hour at 6 amps).
✓ Seat is adjusted comfortably and tightened securely.
✓ All tires are properly inflated. (For shipping purposes, the tires were overinflated at the factory).
✓ Be sure mower deck is properly leveled
side-to-side/front-to-rear for best cutting
results. (Tires must be properly inflated
for leveling).
✓ Check mower and drive belts. Be sure
they are routed properly around pulleys
and inside all belt keepers.
✓ Check wiring. See that all connections
are still secure and wires are properly
clamped.
✓ Before driving tractor, be sure freewheel
control is in “transmission engaged”
position (see “TO TRANSPORT” in the
Operation section of this manual).
While learning how to use your tractor, pay
extra attention to the following impor tant
items:
✓ Engine oil is at proper level.
✓ Fuel tank is filled with fresh, clean, regular unleaded gasoline.
✓ Become familiar with all controls - their
location and function. Operate them
before you start the engine.
✓ Be sure brake system is in safe operating condition.
✓ It is important to purge the transmission
before operating your tractor for the first
time. Follow proper starting and transmission purging instructions (See “TO
START ENGINE” and “PURGE TRANSMISSION” in the Operation section of
this manual).
NOTE: The mulching blades will discharge
and bag grass, but for best bagging and
discharging install the high performance
blades.
1. Remove mulcher plate and mulching
blades and install high performance
blades, (see BLADE REMOVAL in the
Maintenance section of this manual).
2. Store mulching blades and mulcher
plate in a safe place. Your mower is
now ready for discharging or installation of optional grass catcher accessory.
Deflector
Shield
Mulcher
Plate
Latch
Hooks
CHECK TIRE PRESSURE
The tires on your tractor were overinflated
at the factory for shipping purposes. Correct tire pressure is important for best
cutting performance.
• Reduce tire pressure to PSI shown in
“PRODUCT SPECIFICATIONS” section
of this manual.
CHECK DECK LEVELNESS
For best cutting results, mower housing
should be properly leveled. See “TO LEVEL MOWER HOUSING” in the Service
and Adjustments section of this manual.
10
See the figures that are shown for replacing motion and mower blade drive belts
in the Service and Adjustments section
of this manual. Verify that the belts are
routed correctly.
CHECK BRAKE SYSTEM
After you learn how to operate your tractor, check to see that the brake is properly
adjusted. See “TO ADJUST BRAKE” in
the Service and Adjustments section of
this manual.
✔CHECKLIST
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
OPERATION
These symbols may appear on your tractor or in literature supplied with the product.
Learn and understand their meaning.
REVERSE
NEUTRAL
HIGH
LOW
CHOKE
FAST
IGNITION
SLOW
P
ENGINE OFF
LIGHTS ON
OVER TEMP
LIGHT
FUEL
ENGINE ON
OIL PRESSURE
ENGINE START
BATTERY
PARKING BRAKE
REVERSE
FORWARD
PARKING BRAKE
LOCKED
MOWER HEIGHT
15
ATTACHMENT
CLUTCH ENGAGED
ATTACHMENT
CLUTCH DISENGAGED
DANGER, KEEP HANDS
AND FEET AWAY
PARKING BRAKE
UNLOCKED
MOWER LIFT
15
15
SLOPE HAZARDS
KEEP AREA CLEAR
(SEE SAFETY RULES SECTION)
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not avoided,
could result in death or serious injury.
FREE WHEEL
(Automatic Models only)
CAUTION indicates a hazard which, if not avoided,
might result in minor or moderate injury.
Failure to follow instructions
could result in serious injury or
death. The safety alert symbol
is used to identify safety information about hazards which can
result in death, serious injury
and/or property damage.
CAUTION when used without the alert symbol,
indicates a situation that could result in damage
to the tractor and/or engine.
HOT SURFACES indicates a hazard which,
if not avoided, could result in death, serious injury
and/or property damage.
FIRE indicates a hazard which, if not avoided,
could result in death, serious injury and/or
property damage.
11
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
TRACTOR
Compare the illustrations with your tractor to familiarize yourself with the locations of
various controls and adjustments. Save this manual for future reference.
Attachment
Clutch Lever
Light Switch
Position
Ignition
Switch
Lift Lever
Plunger
Choke Control
Throttle Control
Attachment
Lift Lever
Clutch/Brake
Pedal
Height
Adjustment
Knob
Free Wheel
Control
Parking Brake Lever
Motion
Control
Lever
Our tractors conform to the safety standards of the
American National Standards Institute.
LIFT LEVER PLUNGER - Used to release
attachment lift lever when changing its
position.
LIGHT SWITCH POSITION - Turns the
headlights on and off.
PARKING BRAKE LEVER - Locks clutch/
brake pedal into the brake position.
AMMETER - Indicates Charging (+) or
discharging (-) of battery
ATTACHMENT CLUTCH LEVER - Used
to engage the mower blades, or other attachments mounted to your tractor.
ATTACHMENT LIFT LEVER - Used to
raise, lower, and adjust the mower deck or
other attachments mounted to your tractor.
CLUTCH/BRAKE PEDAL - Used for
declutching and braking the tractor and
starting the engine.
MOTION CONTROL LEVER - Selects the
speed and direction of tractor.
IGNITION SWITCH - Used for starting and
stopping the engine.
THROTTLE CONTROL - Used for controlling
engine speed.
CHOKE CONTROL - Used when starting a
cold engine.
FREEWHEEL CONTROL - Disengagages
transmission for pushing or slowly towing
the tractor with the engine off.
HEIGHT ADJUSTMENT KNOB - Used to
adjust the mower cutting height.
12
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
The operation of any tractor can result in foreign objects thrown into the
eyes, which can result in severe eye damage. Always wear safety glasses
or eye shields while operating your tractor or performing any adjustments
or repairs. We recommend standard safety glasses or a wide vision safety
mask worn over spectacles.
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE
Your tractor is equipped with an operator
presence sensing switch. When engine
is running, any attempt by the operator
to leave the seat without first setting the
parking brake will shut off the engine.
1. Depress clutch/brake pedal all the way
down and hold.
2. Pull parking brake lever up and release
pressure from clutch/brake pedal.
Pedal should remain in brake position.
Make sure parking brake will hold tractor secure.
Choke
Control
Throttle
Control
Clutch/
Brake
Pedal
Attachment Clutch Lever
“Engaged” Position
Ignition Key
“Disengaged”
Position
Motion Control
Lever
“Brake”
“Disengaged”
Position
Position Height
Adjustment Knob
IMPORTANT: Leaving the ignition switch
in any position other than “STOP” will
cause the battery to discharge and go
dead.
NOTE: Under certain conditions when
tractor is standing idle with the engine
running, hot engine exhaust gases may
cause “browning” of grass. To eliminate
this possibility, always stop engine when
stopping tractor on grass areas.
CAUTION: Always stop tractor completely, as described above, before leaving
the operator’s position.
TO USE THROTTLE CONTROL
Always operate engine at full throttle.
• Operating engine at less than full
throttle reduces the battery charging
rate.
• Full throttle offers the best bagging and
mower performance.
TO USE CHOKE CONTROL
Use choke control whenever you are starting a cold engine. Do not use to start a
warm engine.
• To engage choke control, pull knob out.
Slowly push knob in to disengage.
Parking Brake
“Engaged”
Position
STOPPING
MOWER BLADES • To stop mower blades, move attachment
clutch lever to disengaged position.
GROUND DRIVE • To stop ground drive, depress clutch/
brake pedal all the way down.
• Move motion control lever to neutral (N)
position.
IMPORTANT: The motion control lever
does not return to neutral (N) position
when the clutch/brake pedal is depressed.
ENGINE • Move throttle control to slow position.
NOTE: Failure to move throttle control to
slow position to allow engine to idle before
stopping may cause engine to “backfire”.
• Turn ignition key to “STOP” position and
remove key. Always remove key when
leaving tractor to prevent unauthorized
use.
• Never use choke to stop engine.
TO MOVE FORWARD AND BACKWARD
The direction and speed of movement is
controlled by the motion control lever.
1. Start tractor with motion control lever in
neutral (N) position.
2. Release parking brake.
3. Slowly move motion control lever to
desired position.
TO ADJUST MOWER CUTTING HEIGHT
The cutting height is controlled by turning the height adjustment knob in desired
direction.
) to raise cut• Turn knob clockwise (
ting height.
) to
• Turn knob counterclockwise (
lower cutting height.
The cutting height range is approximately
1-1/2" to 4". The heights are measured
from the ground to the blade tip with the
engine not running. These heights are approximate and may vary depending upon
soil conditions, height of grass and types
of grass being mowed.
13
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
• The average lawn should be cut to
approximately 2-1/2 inches during the
cool season and to over 3 inches during
hot months. For healthier and better
looking lawns, mow often and after moderate growth.
• For best cutting performance, grass over
6 inches in height should be mowed
twice. Make the first cut relatively high;
the second to desired height.
TO ADJUST GAUGE WHEELS
Gauge wheels are properly adjusted
when they are slightly off the ground when
mower is at the desired cutting height in
operating position. Gauge wheels then
keep the deck in proper position to help
prevent scalping in most terrain conditions.
NOTE: Adjust gauge wheels with tractor
on a flat level surface.
1. Adjust mower to desired cutting height
(See “TO ADJUST MOWER CUTTING
HEIGHT” in this section of manual).
2. With mower in desired height of cut
position, gauge wheels should be
assembled so they are slightly off the
ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8
washer, and 3/8-16 locknut and tighten
securely.
3. Repeat for opposite side, installing
gauge wheel in same adjustment hole.
Gauge
Wheel
Mounting
Bracket
Shoulder
Bolt
TO OPERATE MOWER
Your tractor is equipped with an operator
presence sensing switch. Any attempt
by the operator to leave the seat with the
engine running and the attachment clutch
engaged will shut off the engine.
1. Select desired height of cut.
2. Lower mower with attachment lift control.
3. Start mower blades by engaging attachment clutch control.
TO STOP MOWER BLADES disengage attachment clutch control.
CAUTION: Do not operate the mower
without either the entire grass catcher,
on mowers so equipped, or the deflector
shield in place.
Attachemnt
Lift Lever
High
Position
Low
Position
“Disengaged”
Position
Deflector
Shield
TO OPERATE ON HILLS
WARNING: Do not drive up or down
hills with slopes greater than 15° and do
not drive across any slope. Use the slope
guide at the back of this manual.
• Choose the slowest speed before starting up or down hills.
• Avoid stopping or changing speed on
hills.
• If slowing is necessary, move throttle
control lever to slower position.
• If stopping is absolutely necessary, push
clutch/brake pedal quickly to brake position and engage parking brake.
• Move motion control lever to neutral (N)
position.
IMPORTANT: The motion control lever
does not return to neutral (N) position
when the clutch/brake pedal is depressed.
• To restart movement, slowly release
parking brake and clutch/brake pedal.
• Slowly move motion control lever to
slowest setting.
• Make all turns slowly.
TO TRANSPORT
When pushing or towing your tractor, be
sure to disengage transmission by placing
freewheel control in freewheeling position.
Freewheel control is located at the rear
drawbar of tractor.
1. Raise attachment lift to highest position with attachment lift control.
2. Pull freewheel control out and down
into the slot and release so it is held in
the disengaged position.
• Do not push or tow tractor at more than
two (2) MPH.
• To re-engage transmission, reverse
above procedure.
3/8-16
Locknut
3/8 Washer
Gauge Wheel
Attachment
Clutch Lever
“Engaged”
Position
14
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
Transmission Engaged
Transmission Disengaged
NOTE: To protect hood from damage
when transporting your tractor on a truck
or a trailer, be sure hood is closed and
secured to tractor. Use an appropriate
means of tying hood to tractor (rope, cord,
etc.).
TOWING CARTS AND OTHER ATTACHMENTS
Tow only the attachments that are recommended by and comply with specifications
of the manufacturer of your tractor. Use
common sense when towing. Too heavy
of a load, while on a slope, is dangerous.
Tires can lose traction with the ground and
cause you to lose control of your tractor.
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL
The engine in your tractor has been
shipped, from the factory, already filled
with summer weight oil.
1. Check engine oil with tractor on level
ground.
2. Remove oil fill cap/dipstick and wipe
clean, reinsert the dipstick and screw
cap tight, wait for a few seconds, remove and read oil level. If necessary,
add oil until “FULL” mark on dipstick is
reached. Do not overfill.
• For cold weather operation you should
change oil for easier starting ((See the
oil viscosity chart in the Maintenance
section of this manual).
• To change engine oil, see the Maintenance section in this manual.
ADD GASOLINE
• Fill fuel tank to bottom of tank filler neck.
Do not overfill. Use fresh, clean, regular
unleaded gasoline with a minimum of
87 octane. (Use of leaded gasoline will
increase carbon and lead oxide deposits
and reduce valve life). Do not mix oil
with gasoline. Purchase fuel in quantities that can be used within 30 days to
assure fuel freshness.
CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
IMPORTANT: When operating in temperatures below 32°F(0°C), use fresh, clean
winter grade gasoline to help insure good
cold weather starting.
CAUTION: Alcohol blended fuels (called
gasohol or using ethanol or methanol) can
attract moisture which leads to separation and formation of acids during storage.
Acidic gas can damage the fuel system of
an engine while in storage.
To avoid engine problems, the fuel system
should be emptied before storage of 30
days or longer. Drain the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel
next season. See Storage Instructions for
additional information.
Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
TO START ENGINE
When starting the engine for the first time
or if the engine has run out of fuel, it will
take extra cranking time to move fuel from
the tank to the engine.
1. Be sure freewheel control is in the
transmission engaged position.
2. Sit on seat in operating position,
depress clutch/brake pedal and set
parking brake.
3. Place motion control lever in neutral
(N) position.
4. Move attachment clutch to disengaged
position.
5. Move throttle control to fast position
6. Pull choke control out for a cold engine
start attempt. For a warm engine start
attempt the choke control may not be
needed.
NOTE: Before starting, read the warm and
cold starting procedures below.
7. Insert key into ignition and turn key
clockwise to start position and release
key as soon as engine starts. Do
not run starter continuously for more
than fifteen seconds per minute. If the
engine does not start after several
attempts, push choke control in, wait
a few minutes and try again. If engine
still does not start, pull the choke control out and retry.
15
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
WARM WEATHER STARTING (50° F and
above)
8. When engine starts, slowly push choke
control in until the engine begins to
run smoothly. If the engine starts to
run roughly, pull the choke control out
slightly for a few seconds and then
continue to push the control in slowly.
• The attachments and ground drive can
now be used. If the engine does not
accept the load, restart the engine and
allow it to warm up for one minute using
the choke as described above.
To ensure proper operation and performance, it is recommended that the
transmission be purged before operating
tractor for the first time. This procedure will
remove any trapped air inside the transmission which may have developed during
shipping of your tractor.
IMPORTANT: Should your transmission
require removal for service or replacement, it should be purged after reinstallation before operating the tractor.
1. Place tractor safely on level surface
with engine off and parking brake set.
2. Disengage transmission by placing
freewheel control in “transmission disengaged” position (See “TO TRANSPORT” in this section of manual).
3. Sitting in the tractor seat, start engine.
After the engine is running, move
throttle control to slow position. With
motion control lever in neutral (N)
position, slowly disengage clutch/brake
pedal.
4. Move motion control lever to full
forward position and hold for five (5)
seconds. Move lever to full reverse
position and hold for five (5) seconds.
Repeat this procedure three (3) times.
NOTE: During this step there will be no
movement of drive wheels. The air is being removed from hydraulic drive system.
5. Move motion control lever to neutral
(N) position. Shutoff engine and set
parking brake.
6. Engage transmission by placing
freewheel control in “transmission
engaged” position (See “TO TRANSPORT” in this section of manual).
7. Sitting in the tractor seat, start engine.
After the engine is running, move
throttle control to half (1/2) speed.
With motion control lever in neutral (N)
position, slowly disengage clutch/brake
pedal.
8. Slowly move motion control lever
forward, after the tractor moves approximately five (5) feet, slowly move
motion control lever to reverse position.
After the tractor moves approximately
five (5) feet return the motion control
lever to the neutral (N) position. Repeat
this procedure with the motion control
lever three (3) times.
Your transmission is now purged and
ready for normal operation.
COLD WEATHER STARTING (50° F and
below)
8. When engine starts, slowly push choke
control in until the engine begins to run
smoothly. Continue to push the choke
control in small steps allowing the engine to accept small changes in speed
and load, until the choke control is fully
in. If the engine starts to run roughly,
pull the choke control out slightly for a
few seconds and then continue to push
the control in slowly. This may require
an engine warm-up period from several
seconds to several minutes, depending
on the temperature.
AUTOMATIC TRANSMISSION WARM UP
Before driving the unit in cold weather,
the transmission should be warmed up as
follows:
1. Be sure the tractor is on level ground.
2. Place the motion control lever in
neutral. Release the parking brake and
let the clutch/brake slowly return to
operating position.
3. Allow one minute for transmission to
warm up. This can be done during the
engine warm up period.
• The attachments can be used during
the engine warm-up period after the
transmission has been warmed up and
may require the choke control be pulled
out slightly.
NOTE: If at a high altitude (above 3000
feet) or in cold temperatures (below 32 F)
the carburetor fuel mixture may need to
be adjusted for best engine performance
(see “TO ADJUST CARBURETOR” in the
Service and Adjustments section of this
manual).
PURGE TRANSMISSION
CAUTION: Never engage or disengage freewheel lever while the engine
is running.
16
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
MOWING TIPS
MULCHING MOWING TIPS
• Mower should be properly leveled for
best mowing performance. See “TO
LEVEL MOWER HOUSING” in the
Service and Adjustments section of this
manual.
• The left hand side of mower should be
used for trimming.
• Drive so that clippings are discharged
onto the area that has already been
cut. Have the cut area to the right of
the tractor. This will result in a more
even distribution of clippings and more
uniform cutting.
• When mowing large areas, start by
turning to the right so that clippings will
discharge away from shrubs, fences,
driveways, etc. After one or two rounds,
mow in the opposite direction making
left hand turns until finished.
IMPORTANT: For best performance, keep
mower housing free of built-up grass and
trash. Clean after each use.
• The special mulching blade will recut
the grass clippings many times and
reduce them in size so that as they fall
onto the lawn they will disperse into
the grass and not be noticed. Also, the
mulched grass will biodegrade quickly
to provide nutrients for the lawn. Always
mulch with your highest engine (blade)
speed as this will provide the best recutting action of the blades.
• Avoid cutting your lawn when it is wet.
Wet grass tends to form clumps and
interferes with the mulching action. The
best time to mow your lawn is the early
afternoon. At this time the grass has
dried and the newly cut area will not be
exposed to the direct sun.
• For best results, adjust the mower
cutting height so that the mower cuts
off only the top one-third of the grass
blades. For extremely heavy grass,
reduce your width of cut on each pass
and mow slowly.
Max 1/3
• If grass is extremely tall, it should be
mowed twice to reduce load and possible fire hazard from dried clippings.
Make first cut relatively high; the second
to the desired height.
• Do not mow grass when it is wet.
Wet grass will plug mower and leave
undesirable clumps. Allow grass to dry
before mowing.
• Always operate engine at full throttle
when mowing to assure better mowing
performance and proper discharge of
material. Regulate ground speed by
selecting a low enough gear to give the
mower cutting performance as well as
the quality of cut desired.
• When operating attachments, select a
ground speed that will suit the terrain
and give best performance of the attachment being used.
• Certain types of grass and grass
conditions may require that an area be
mulched a second time to completely
hide the clippings. When doing a second cut, mow across or per pendicular to
the first cut path.
• Change your cutting pattern from week
to week. Mow north to south one week
then change to east to west the next
week. This will help prevent matting and
graining of the lawn.
17
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
MAINTENANCE
MAINTENANCE SCHEDULE
FILL IN DATES
AS YOU COMPLETE
REGULAR SERVICE
E
E
RS
S
AG
RS
RS
US
OU SON OR
UR
OU HOU
H
T
O
H
A
0
S
E
8H
SE RE
25
10
50
Y
Y
Y
Y
Y
RE
ER VER VER VER VER EFO
FO
V
E
B
SERVICE
E
E
E
E
E
B
H
AC
DATES
Check Brake Operation
Check Tire Pressure
T
R
A
C
T
0
R
Check Operator Presence and
Interlock Systems
Check for Loose Fasteners
5
Sharpen/Replace Mower Blades
3
Lubrication Chart
Check Battery Level
4
Clean Battery and Terminals
Check Transaxle Cooling
Check V-Belts
Check Engine Oil Level
Change Engine Oil (with oil filter)
1,2
Clean Air Filter
2
Clean Air Screen
2
Inspect Muffler/Spark Arrester
Replace Oil Filter (If equipped)
1, 2
Clean Engine Cooling Fins
maint_sch-tractore.new1
E
N
G
I
N
E
1,2
Change Engine Oil (without oil filter)
2
Replace Spark Plug
Replace Air Filter Paper Cartridge
2
Replace Fuel Filter
1 - Change more often when operating under a heavy load or
in high ambient temperatures.
2 - Service more often when operating in dirty or dusty conditions.
3 - Replace blades more often when mowing in sandy soil.
4 - Not required if equipped with maintenance-free battery.
5 - Tighten front axle pivot bolt to 35 ft.-lbs. maximum.
Do not overtighten.
GENERAL RECOMMENDATIONS
LUBRICATION CHART
The warranty on this tractor does not
cover items that have been subjected to
operator abuse or negligence. To receive
full value from the warranty, operator
must maintain tractor as instructed in this
manual.
Some adjustments will need to be made
periodically to properly maintain your
tractor.
All adjustments in the Service and Adjustments section of this manual should be
checked at least once each season.
• Once a year you should replace the
spark plug, clean or replace air filter,
and check blades and belts for wear.
A new spark plug and clean air filter
assure proper air-fuel mixture and help
your engine run better and last longer.
➀ Spindle
➀ Spindle
Zerk
Zerk
➀Front Wheel
➀Front Wheel
Bearing Zerk
Bearing
Zerk
➁Engine
01964
➀ General Purpose Grease
➁ REFER TO Maintenance “ENGINE” SECTION
BEFORE EACH USE
IMPORTANT: Do not oil or grease the
pivot points which have special nylon
bearings. Viscous lubricants will attract
dust and dirt that will shorten the life of the
self-lubricating bearings. If you feel they
must be lubricated, use only a dry, powdered graphite type lubricant sparingly.
1.
2.
3.
4.
Check engine oil level.
Check brake operation.
Check tire pressure.
Check operator presence and
interlock systems for proper operation.
5. Check for loose fasteners.
18
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR
Always observe safety rules when performing any maintenance.
BRAKE OPERATION
If tractor requires more than six (6) feet
stopping distance at high speed in highest
gear, then brake must be adjusted. (See
“TO ADJUST BRAKE” in the Service and
Adjustments section of this manual).
TIRES
• Maintain proper air pressure in all tires
(See “PRODUCT SPECIFICATIONS”
section of this manual).
• Keep tires free of gasoline, oil, or insect
control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may
cause tire damage.
NOTE: To seal tire punctures and prevent
flat tires due to slow leaks, tire sealant
may be purchased from your local parts
dealer. Tire sealant also prevents tire dry
rot and corrosion.
OPERATOR PRESENCE SYSTEM
Be sure operator presence and interlock
systems are working properly. If your tractor does not function as described, repair
the problem immediately.
• The engine should not start unless
the brake pedal is fully depressed and
attachement clutch control is in the
disengaged position.
• When the engine is running, any attempt by the operator to leave the seat
without first setting the parking brake
should shut off the engine.
• When the engine is running and the
attachment clutch is engaged, any attempt by the operator to leave the seat
should shut off the engine.
• The attachment clutch should never operate unless the operator is in the seat.
BLADE CARE
For best results mower blades must be
kept sharp. Replace bent or damaged
blades.
BLADE REMOVAL
1. Raise mower to highest position to allow access to blades.
2. Remove blade bolt, lock washer and
flat washer securing blade.
3. Install new or resharpened blade
with trailing edge up towards deck as
shown.
IMPORTANT: To ensure proper assembly,
center hole in blade must align with star
on mandrel assembly.
4. Reassemble blade bolt, lock washer
and flat washer in exact order as
shown.
5. Tighten blade bolt securely (27-35 Ft.
Lbs. torque).
IMPORTANT: Blade bolt is grade 8 heat
treated.
Trailing Edge Blade
Up
Center
Hole
Flat
Washer
Lock
Washer
Mandrel
Assembly
Star
Blade Bolt (Grade 8)*
*A Grade 8 Heat Treated Bolt Can Be
Identified By Six Lines On The Bolt Head
TO SHARPEN BLADE
NOTE: We do not recommend sharpening blade - but if you do, be sure the
blade is balanced.
Care should be taken to keep the blade
balanced. An unbalanced blade will cause
excessive vibration and eventual damage
to mower and engine.
• The blade can be sharpened with a file
or on a grinding wheel. Do not attempt
to sharpen while on the mower.
• To check blade balance, you will need a
5/8" diameter steel bolt, pin, or a cone
balancer. (When using a cone balancer,
follow the instructions supplied with
balancer.)
NOTE: Do not use a nail for balancing
blade. The lobes of the center hole may
appear to be centered, but are not.
• Slide blade on to an unthreaded portion
of the steel bolt or pin and hold the
bolt or pin parallel with the ground. If
blade is balanced, it should remain in a
horizontal position. If either end of the
blade moves downward, sharpen the
heavy end until the blade is balanced.
Blade
5/8” Bolt or Pin
Center Hole
BATTERY
Your tractor has a battery charging system
which is sufficient for normal use. However, periodic charging of the battery with
an automotive charger will extend its life.
• Keep battery and terminals clean.
• Keep battery bolts tight.
• Keep small vent holes open.
• Recharge at 6-10 amperes for 1 hour.
NOTE: The original equipment battery on
your tractor is maintenance free. Do not
attempt to open or remove caps or covers.
Adding or checking level of electrolyte is
not necessary.
19
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TO CLEAN BATTERY AND TERMINALS
Corrosion and dirt on the battery and
terminals can cause the battery to “leak”
power.
1. Disconnect BLACK battery cable first
then RED battery cable and remove
battery from tractor.
2. Rinse the battery with plain water and
dry.
3. Clean terminals and battery cable ends
with wire brush until bright.
4. Coat terminals with grease or petroleum jelly.
5. Reinstall battery (See “REPLACING
BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual).
TRANSAXLE COOLING
The transmission fan and cooling fins
should be kept clean to assure proper
cooling.
Do not attempt to clean fan or transmission while engine is running or while the
transmission is hot. To prevent possible
damage to seals, do not use high pressure water or steam to clean transaxle.
• Inspect cooling fan to be sure fan blades
are intact and clean.
• Inspect cooling fins for dirt, grass clippings and other materials. To prevent
damage to seals, do not use compressed air or high pressure sprayer to
clean cooling fins.
TRANSAXLE PUMP FLUID
The transaxle was sealed at the factory
and fluid maintenance is not required for
the life of the transaxle. Should the transaxle ever leak or require servicing, contact
our authorized service center/department.
V-BELTS
Check V-belts for deterioration and wear
after 100 hours of operation and replace
if necessary. The belts are not adjustable.
Replace belts if they begin to slip from
wear.
NOTE: Although multi-viscosity oils
(5W30, 10W30 etc.) improve starting in
cold weather, these multi-viscosity oils will
result in increased oil consumption when
used above 32°F. Check your engine oil
level more frequently to avoid possible
engine damage from running low on oil.
Change the oil after every 50 hours of operation or at least once a year if the tractor
is not used for 50 hours in one year.
Check the crankcase oil level before starting the engine and after each eight (8)
hours of operation. Tighten oil fill cap/
dipstick securely each time you check the
oil level.
TO CHANGE ENGINE OIL
Determine temperature range expected
before oil change. All oil must meet API
service classification SF-SJ.
• Be sure tractor is on level surface.
• Oil will drain more freely when warm.
• Catch oil in a suitable container.
1. Remove oil fill cap/dipstick. Be careful
not to allow dirt to enter the engine
when changing oil.
2. Remove yellow cap from end of drain
valve and install the drain tube onto the
fitting.
Oil Drain Valve
Closed and
Locked
Position
Yellow
Cap
02463
3. Unlock drain valve by pushing inward
slightly and turning counterclockwise.
4. To open, pull out on the drain valve.
5. After oil has drained completely, close
and lock the drain valve by pushing
inward and turning clockwise until the
pin is in the locked position as shown.
6. Remove the drain tube and replace the
cap onto the end of the drain valve.
7. Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill.
For approximate capacity see “PRODUCT SPECIFICATIONS” section of this
manual.
8. Use gauge on oil fill cap/dipstick for
checking level. For accurate reading,
tighten dipstick cap securely onto the
tube before removing dipstick. Keep oil
at “FULL” line on dipstick. Tighten cap
onto the tube securely when finished.
ENGINE
LUBRICATION
Only use high quality detergent oil rated
with API service classification SF-SJ.
Select the oil’s SAE viscosity grade
according to your expected operating
temperature.
SAE VISCOSITY GRADES
SAE 30
5W-30
-20
F
C
-30
0
-20
30
-10
32
0
40
60
10
100
80
20
30
Drain
Tube
40
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE
oil_visc_chart1_e
20
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
AIR FILTER
Your engine will not run properly using a
dirty air filter. Clean the foam pre-cleaner
after every 25 hours of operation or every
season. Service paper cartridge every
100 hours of operation or every season,
whichever occurs first.
Service air cleaner more often under dusty
conditions.
1. Remove knobs and cover.
TO SERVICE PRE-CLEANER
2. Wash it in liquid detergent and water.
3. Squeeze it dry in a clean cloth.
4. Saturate it in engine oil. Wrap it in
clean, absorbent cloth and squeeze to
remove excess oil.
NOTE: If very dirty or damaged, replace
pre-cleaner.
TO SERVICE CARTRIDGE
1. Clean cartridge by tapping gently on
flat surface. If very dirty or damaged,
replace cartridge.
2. Reinstall precleaner cartridge, cover
and secure with knobs.
IMPORTANT: Petroleum solvents, such
as kerosene, are not to be used to clean
the cartridge. They may cause deterioration of the cartridge. Do not oil cartridge.
Do not use pressurized air to clean or dry
car tridge.
Knobs
Cover
Cartridge
Every 100 hours of operation (more often
under extremely dusty, dirty conditions),
remove the blower housing and other cooling shrouds. Clean the cooling fins and
external surfaces as necessary. Make sure
the cooling shrouds are reinstalled.
NOTE: Operating the engine with a
blocked grass screen, dirty or plugged
cooling fins, and/or cooling shrouds
removed will cause engine damage due to
overheating.
MUFFLER
Inspect and replace corroded muffler and
spark arrester (if equipped) as it could
create a fire hazard and/or damage.
SPARK PLUG(S)
Replace spark plug(s) at the beginning
of each mowing season or after every
100 hours of operation, whichever occurs
first. Spark plug type and gap setting are
shown in “PRODUCT SPECIFICATIONS”
section of this manual.
IN-LINE FUEL FILTER
The fuel filter should be replaced once
each season. If fuel filter becomes
clogged, obstructing fuel flow to carburetor, replacement is required.
1. With engine cool, remove filter and
plug fuel line sections.
2. Place new fuel filter in position in fuel
line with arrow pointing towards carburetor.
3. Be sure there are no fuel line leaks
and clamps are properly positioned.
4. Immediately wipe up any spilled gasoline.
Clamp
Foam
Pre-Cleaner
Clamp
Fuel Filter
CLEAN AIR SCREEN
Air screen must be kept free of dirt and
chaff to prevent engine damage from
overheating. Clean with a wire brush or
compressed air to remove dirt and stubborn dried gum fibers.
CLEAN AIR INTAKE/COOLING AREAS
To insure proper cooling, make sure the
grass screen, cooling fins, and other
external surfaces of the engine are kept
clean at all times.
CLEANING
• Clean engine, battery, seat, finish, etc.
of all foreign matter.
• Keep finished surfaces and wheels free
of all gasoline, oil, etc.
• Protect painted surfaces with automotive type wax.
We do not recommend using a garden
hose to clean your tractor unless the
electrical system, muffler, air filter and
carburetor are covered to keep water out.
Water in engine can result in a shortened
engine life.
21
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
SERVICE AND ADJUSTMENTS
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY
SERVICE OR ADJUSTMENTS:
1. Depress clutch/brake pedal fully and set parking brake.
2. Place motion control lever in neutral (N) position.
3. Place attachment clutch in “DISENGAGED” position.
4. Turn ignition key to “STOP” and remove key.
5. Make sure the blades and all moving parts have completely stopped.
6. Disconnect spark plug wire from spark plug and place wire where it cannot
come in contact with plug.
TRACTOR
IMPORTANT: If an attachment other than
the mower deck is to be mounted on the
tractor, remove the front links and hook
the clutch spring Into square hole in frame.
TO INSTALL MOWER
1. Raise attachment lift lever to its highest
position.
2. Slide mower under tractor with deflector shield to right side of tractor.
3. Lower lift lever to its lowest position.
4. Connect front links to mower deck and
secure with retainer springs.
5. Connect suspension arms to rear
deck brackets and secure with retainer
springs.
6. Connect anti-sway bar to chassis
bracket and secure with retainer
spring.
7. Push clutch cable housing guide into
bracket, slide collar onto guide and
secure with large retainer spring.
8. Place flat washer and clutch spring on
idler pulley bolt and secure with small
retainer spring.
9. Install belt onto engine pulley.
TO REMOVE MOWER
Mower will be easier to remove from the
right side of tractor.
1. Place attachment clutch in “DISENGAGED” position.
2. Move attachment lift lever forward to
lower mower to its lowest position.
3. Roll belt off engine pulley.
4. Remove small retainer spring, and
remove clutch spring off pulley bolt.
5. Remove large retainer spring, slide
collar off and push housing guide out
of bracket.
6. Disconnect anti-sway bar from chassis
bracket by removing retainer spring.
7. Disconnect suspension arms from rear
deck brackets by removing retainer
springs.
8. Disconnect front links from deck by
removing retainer springs.
9. Raise lift lever to raise suspension
arms. Slide mower out from under tractor.
Flat Washer
Small Retainer Spring
Clutch
Spring
Clutch Spring
Small Retainer
Spring
Suspension
Arms
Retainer
Spring
Anti-Sway
Bar
Engine
Pulley
Front Link
Retainer Springs
(Both Sides)
Collar
Housing
Guide
Square Hole
Deflector
Shield
Large Retainer
Spring
Bracket
22
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TO LEVEL MOWER HOUSING
Adjust the mower while tractor is parked
on level ground or driveway. Make sure
tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this
manual). If tires are over or underinflated,
you will not properly adjust your mower.
SIDE-TO-SIDE ADJUSTMENT
• Raise mower to its highest position.
• At the midpoint of both sides of mower,
measure height from bottom edge of
mower to ground. Distance “A” on both
sides of mower should be the same or
within 1/4" of each other.
• If adjustment is necessary, make adjustment on one side of mower only.
• To raise one side of mower, tighten lift
link adjustment nut on that side.
• To lower one side of mower, loosen lift
link adjustment nut on that side.
NOTE: Each full turn of adjustment nut
will change mower height about 1/8".
• Recheck measurements after adjusting.
Mandrel
“D”
“D”
Both Front Links Should be Equal in Length
Bottom edge of
mower to ground
Bottom edge
of mower to
ground
A
• When distance “D” is 1/8" to 1/2"
lower at front than rear, tighten nuts “F”
against trunnion on both front links.
• To raise front of mower, loosen nut “F”
from trunnion on both front links. Tighten
nut “E” on both front links an equal
number of turns.The two front links must
remain equal in length.
• When distance “D” is 1/8" to 1/2" lower
at front than rear, tighten nut “F” against
trunnion on both front links.
• Recheck side-to-side adjustment.
Nut “E”
Nut “F”
Ground Line
A
Trunnion
Suspension Arm
Lift Link
Adjustment Nut
Front Links
FRONT-TO-BACK ADJUSTMENT
IMPORTANT: Deck must be level side-to
side. If the following front-to-back adjustment is necessary, be sure to adjust both
front links equally so mower will stay level
side-to-side.
To obtain the best cutting results, the
mower housing should be adjusted so
that the front is approximately 1/8" to 1/2"
lower than the rear when the mower is in
its highest position.
Check adjustment on right side of tractor. Measure distance “D” directly in front
and behind the mandrel at bottom edge of
mower housing as shown.
• Before making any necessary adjustments, check that both front links are
equal in length.
• If links are not equal in length, adjust
one link to same length as other link.
• To lower front of mower loosen nut “E”
on both front links an equal number of
turns.
TO REPLACE MOWER BLADE DRIVE
BELT
The mower blade drive belt may be replaced without tools. Park the tractor on
level surface. Engage parking brake.
BELT REMOVAL 1. Remove mower from tractor (See “TO
REMOVE MOWER” in this section of
manual).
2. Work belt off both mandrel pulleys and
idler pulleys.
3. Pull belt away from mower.
BELT INSTALLATION 1. Work belt around both mandrel pulleys
and idler pulleys
2. Make sure belt is in all pulley grooves
and inside all belt guides.
3. Install mower (See “To Install Mower”
in this section of this manual).
23
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
Mandrel
Pulley
With Parking Brake “Engaged”
Idler Pulleys
1-9/16”
Nut “A”
Jam Nut
Mandrel
Pulley
Operating
Arm
TO CHECK AND ADJUST BRAKE
Your tractor is equipped with an adjustable
brake system which is mounted on the
right side of the transaxle.
If tractor requires more than five (5) feet to
stop at highest speed in highest gear on a
level, dry concrete or paved surface, then
brake must be checked and adjusted.
01513
Do Not touch this nut. If further brake
adjustment is necessary contact an authorized
service center/department.
TO REPLACE MOTION DRIVE BELT
Park the tractor on level surface. Engage
parking brake. For assistance, there is a
belt installation guide decal on bottom side
of left footrest.
TO CHECK BRAKE
1. Park tractor on a level, dry concrete or
paved surface, depress clutch/brake
pedal all the way down and engage
parking brake.
2. Disengage transmission by placing
freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so
it is held in the disengaged position.
The rear wheels must lock and skid when
you try to manually push the tractor forward. If the rear wheels rotate, the brake
needs to be adjusted or the pads need to
be replaced.
BELT REMOVAL 1. Remove mower (See “TO REMOVE
MOWER” in this section of manual).
NOTE: Observe entire motion drive belt
and position of all belt guides and keepers.
2. Remove belt from stationary idler and
clutching idler.
3. Remove belt downward from around
engine pulley.
4. Pull belt slack toward rear of tractor.
Carefully remove belt upwards from
transmission input pulley and over
cooling fan blades.
5. Remove belt from center span keeper
and pull belt away from tractor.
TO ADJUST BRAKE
1. Depress clutch/brake pedal all the way
down and engage parking brake.
2. Measure distance between brake operating arm and nut “A” on brake rod.
3. If distance is other than 1-9/16", loosen
jam nut and turn nut “A” until distance
becomes 1-9/16". Retighten jam nut
against nut “A”.
4. Engage transmission by placing
freewheel control in “transmission
engaged” position.
5. Road test tractor for proper stopping
distance as stated above. Readjust
if necessary. If stopping distance is
still greater than five (5) feet in highest
gear, further maintenance is necessary.
Replace brake pads or contact our
authorized service center/department.
BELT INSTALLATION 1. Carefully work new belt down around
transmission cooling fan and onto the
input pulley.
2. Slide belt into the center span keeper.
3. Pull belt toward front of tractor and roll
around the top groove of engine pulley.
4. Install belt through stationary idler and
clutching idler.
5. Make sure belt is in all pulley grooves
and inside all belt guides and keepers.
6. Install mower (See “TO INSTALL
MOWER” in this section of manual).
24
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TO ADJUST STEERING WHEEL ALIGNMENT
If steering wheel crossbars are not
horizontal (left to right) when wheels are
positioned straight forward, remove steering wheel and reassemble with crossbars
horizontal. Tighten securely.
FRONT WHEEL TOE-IN/CAMBER
The front wheel toe-in and camber are not
adjustable on your tractor. If damage has
occurred to affect the front wheel toe-in
or camber, contact our authorized service
center/department.
Engine Pulley
Clutching Idler
Stationary Idler
Center Span
Keeper
Transmission
Input Pulley
TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT
The motion control lever has been preset
at the factory and adjustment should not
be necessary.
1. Loosen adjustment bolt in front of the
right rear wheel, and lightly tighten.
2. Start engine and move motion control lever until tractor does not move
forward or backward.
3. Hold motion control lever in that position and turn engine off.
4. While holding motion control lever in
place, loosen the adjustment bolt.
5. Move motion control lever to the neutral (N) (lock gate) position.
6. Tighten adjustment bolt securely.
NOTE: If additional clearance is needed
to get to adjustment bolt, move mower
deck height to the lowest position.
After above adjustment is made, if the
tractor still creeps forward or backward
while motion control lever is in neutral
position, follow these steps:
1. Loosen the adjustment bolt.
2. Move the motion control lever 1/4 to
1/2 inch in the direction it is trying to
creep.
3. Tighten adjustment bolt securely.
4. Start engine and test.
5. If tractor still creeps, repeat above
steps until satisfied.
Motion Control
Lever
02239
Neutral
Lock Gate
Adjustment
Bolt
TRANSMISSION REMOVAL/
REPLACEMENT
Should your transmission require removal
for service or replacement, it should be
purged after reinstallation and before operating the tractor. See “PURGE TRANSMISSION” in the Operation section of this
manual.
TO REMOVE WHEEL FOR REPAIRS
1. Block up axle securely.
2. Remove axle cover, retaining ring and
washers to allow wheel removal (rear
wheels have a square key - Do not
lose).
3. Repair tire and reassemble.
NOTE: On rear wheels only: align
grooves in rear wheel hub and axle. Insert
square key.
4. Replace washers and snap retaining
ring securely in axle groove.
5. Replace axle cover.
NOTE: To seal tire punctures and prevent
flat tires due to slow leaks, purchase and
use tire sealant from an authorized service center/department. Tire sealant also
prevents tire dry rot and corrosion.
Washers
Retaining
Ring
Axle
Cover
Square Key
(Rear Wheel Only)
TO START ENGINE WITH A WEAK BATTERY
WARNING: Lead-acid batteries
generate explosive gases. Keep sparks,
flame and smoking materials away from
batteries. Always wear eye protection
when around batteries.
If your battery is too weak to start the
engine, it should be recharged. (See "BATTERY" in the MAINTENANCE section of
this manual).
If “jumper cables” are used for emergency
starting, follow this procedure:
IMPORTANT: Your tractor is equipped
with a 12 volt system. The other vehicle
must also be a 12 volt system. Do not use
your tractor battery to start other vehicles.
25
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
Terminal
Cover
TO ATTACH JUMPER CABLES 1. Connect one end of the RED cable
to the POSITIVE (+) terminal of each
battery(A-B), taking care not to short
against tractor chassis.
2. Connect one end of the BLACK cable
to the NEGATIVE (-) terminal (C) of
fully charged battery.
3. Connect the other end of the BLACK
cable (D) to good chassis ground,
away from fuel tank and battery.
Hex
Bolt
Negative
(Black)
Cable
Positive
(Red)
Cable
TO REMOVE CABLES, REVERSE
ORDER 1. BLACK cable first from chassis and
then from the fully charged battery.
2. RED cable last from both batteries.
Weak or Dead
Battery
Keps
Nut
Fully Charged
Battery
REPLACING BATTERY
WARNING: Do not short battery
terminals by allowing a wrench or any
other object to contact both terminals at
the same time. Before connecting battery,
remove metal bracelets, wristwatch bands,
rings, etc.
Positive terminal must be connected
first to prevent sparking from accidental
grounding.
1. Lift seat pan to raised position.
2. Disconnect BLACK battery cable first
then RED battery cable and carefully
remove battery from tractor.
3. Install new battery with terminals in
same position as old battery.
4. First connect RED battery cable to
positive (+) terminal with hex bolt and
keps nut as shown. Tighten securely.
Slide terminal cover over terminal
5. Connect BLACK grounding cable to
negative (-) terminal with remaining
hex bolt and keps nut. Tighten securely.
Seat Pan
26
TO REPLACE HEADLIGHT BULB
1. Raise hood.
2. Pull bulb holder out of the hole in the
backside of the grill.
3. Replace bulb in holder and push bulb
holder securely back into the hole in
the backside of the grill.
4. Close hood.
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause
your tractor to run poorly, stop running, or
prevent it from starting.
• Check wiring. See electrical wiring
diagram in the Repair Parts section.
TO REPLACE FUSE
Replace with 20 amp automotive-type
plug-in fuse. The fuse holder is located
behind the dash.
TO REMOVE HOOD AND GRILL ASSEMBLY
1. Raise hood.
2. Unsnap headlight wire connector.
3. Stand in front of tractor. Grasp hood at
sides, tilt toward engine and lift off of
tractor.
4. When replacing hood, be sure to
reconnect the headlight wire connector.
Hood
Headlight Wire
Connector
01765
ENGINE
TO ADJUST THROTTLE CONTROL
CABLE
The throttle control has been preset at the
factory and adjustment should not be necessary. Check adjustment as described
below before loosening cable. If adjustment is necessary, see eingine manual.
TO ADJUST CARBURETOR
The carburetor has been preset at the
factory and adjustment should not be necessary. However, minor adjustment may
be required to compensate for differences
in fuel, temperature, altitude or load. If
the carburetor des need adjustment, see
engine manual.
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
STORAGE
Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.
WARNING: Never store the tractor
with gasoline in the tank inside a building
where fumes may reach an open flame
or spark. Allow the engine to cool before
storing in any enclosure.
TRACTOR
Remove mower from tractor for winter
storage. When mower is to be stored for a
period of time, clean it thoroughly, remove
all dirt, grease, leaves, etc. Store in a
clean, dry area.
1. Clean entire tractor (See “CLEANING”
in the Maintenance section of this
manual).
2. Inspect and replace belts, if necessary
(See belt replacement instructions in
the Service and Adjustments section of
this manual).
3. Lubricate as shown in the Maintenance section of this manual.
4. Be sure that all nuts, bolts and screws
are securely fastened. Inspect moving
parts for damage, breakage and wear.
Replace if necessary.
5. Touch up all rusted or chipped paint
surfaces; sand lightly before painting.
BATTERY
• Fully charge the battery for storage.
• After a period of time in storage, battery
may require recharging.
• To help prevent corrosion and power
leakage during long periods of storage,
battery cables should be disconnected
and battery cleaned thoroughly (see
“TO CLEAN BATTERY AND TERMINALS” in the Maintenance section of
this manual).
• After cleaning, leave cables disconnected and place cables where they
cannot come in contact with battery
terminals.
• If battery is removed from tractor for
storage, do not store battery directly on
concrete or damp surfaces.
ENGINE
FUEL SYSTEM
IMPORTANT: It is important to prevent
gum deposits from forming in essential
fuel system parts such as carburetor, fuel
hose, or tank during storage.
Also, alcohol blended fuels (called gasohol
or using ethanol or methanol) can attract
moisture which leads to separation and
formation of acids during storage. Acidic
gas can damage the fuel system of an
engine while in storage.
1. Drain the fuel tank.
2. Start the engine and let it run until the
fuel lines and carburetor are empty.
• Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
• Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable
alternative in minimizing the formation of
fuel gum deposits during storage. Add
stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio
found on stabilizer container. Run engine
at least 10 minutes after adding stabilizer
to allow the stabilizer to reach the carburetor. Do not drain the gas tank and
carburetor if using fuel stabilizer.
ENGINE OIL
Drain oil (with engine warm) and replace
with clean engine oil. (See “ENGINE” in
the Maintenance section of this manual).
CYLINDER(S)
1. Remove spark plug(s).
2. Pour one ounce of oil through spark
plug hole(s) into cylinder(s).
3. Turn ignition key to start position for a
few seconds to distribute oil.
4. Replace with new spark plug(s).
OTHER
• Do not store gasoline from one season
to another.
• Replace your gasoline can if your can
starts to rust. Rust and/or dirt in your
gasoline will cause problems.
• If possible, store your tractor indoors
and cover it to give protection from dust
and dirt.
• Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot
breathe which allows condensation to
form and will cause your tractor to rust.
IMPORTANT: Never cover tractor while
engine and exhaust areas are still warm.
27
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TROUBLESHOOTING CHART:
PROBLEM
CAUSE
CORRECTION
Will not start
1. Out of fuel.
2. Engine not “CHOKED”
properly.
3. Engine flooded.
1. Fill fuel tank.
2. See “TO START ENGINE”
in Operation section.
3. Wait several minutes before
attempting to start.
4. Bad spark plug.
4. Replace spark plug.
5. Dirty air filter.
5. Clean/replace air filter.
6. Dirty fuel filter.
6. Replace fuel filter.
7. Water in fuel.
7. Drain fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel
filter.
8. Loose or damaged wiring.
8. Check all wiring.
9. Carburetor out of adjustment. 9. See “To Adjust Carburetor”
in Service and Adjustments
section.
10. Engine valves out of
10. Contact our authorized
adjustment.
service center/department.
Hard to start
1.
2.
3.
4.
5.
Engine will not
turn over
1. Brake pedal not depressed.
2. Attachment clutch is
engaged.
3. Weak or dead battery.
4. Blown fuse.
5. Corroded battery terminals.
6. Loose or damaged wiring.
7. Faulty ignition switch.
Dirty air filter.
Bad spark plug.
Weak or dead battery.
Dirty fuel filter.
Stale or dirty fuel.
1.
2.
3.
4.
5.
Clean/replace air filter.
Replace spark plug.
Recharge or replace battery.
Replace fuel filter.
Drain fuel tank and refill with
fresh gasoline.
6. Loose or damaged wiring.
6. Check all wiring.
7. Carburetor out of adjustment. 7. See “To Adjust Carburetor”
in Service and Adjustments
section.
8. Engine valves out of
8. Contact our authorized
adjustment.
service center/department.
9. Faulty operator presence
switch(es).
1. Depress brake pedal.
2. Disengage attachment
clutch.
3. Recharge or replace battery.
4. Replace fuse.
5. Clean battery terminals.
6. Check all wiring.
7. Check/replace ignition
switch.
8. Check/replace solenoid or
starter.
9. Contact our authorized
service center/department.
Engine clicks but
will not start
1.
2.
3.
4.
1.
2.
3.
4.
Loss of power
1. Cutting too much grass/too
1. Set in “Higher Cut” position/
fast.
reduce speed.
2. Throttle in “CHOKE” position. 2. Adjust throttle control.
8. Faulty solenoid or starter.
Weak or dead battery.
Corroded battery terminals.
Loose or damaged wiring.
Faulty solenoid or starter.
Recharge or replace battery.
Clean battery terminals.
Check all wiring.
Check/replace solenoid or
starter.
28
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TROUBLESHOOTING CHART:
PROBLEM
CAUSE
CORRECTION
Loss of power
(continued)
3. Build-up of grass, leaves
and trash under mower.
4. Dirty air filter.
5. Low oil level/dirty oil.
6. Faulty spark plug.
3. Clean underside of mower
housing.
4. Clean/replace air filter.
5. Check oil level/change oil.
6. Clean and regap or change
spark plug.
7. Replace fuel filter.
8. Drain fuel tank and refill
with fresh gasoline.
9. Drain fuel tank and
carburetor, refill tank with
fresh gasoline and replace
fuel filter.
10. Connect and tighten spark
plug wire.
11. Clean engine air screen/
fins.
12. Clean/replace muffler.
13. Check all wiring.
14. See “To Adjust Carburetor”
in Service and Adjustments
section.
15. Contact our authorized
service center/department.
7. Dirty fuel filter.
8. Stale or dirty fuel.
9. Water in fuel.
10. Spark plug wire loose.
11. Dirty engine air screen/fins.
12. Dirty/clogged muffler.
13. Loose or damaged wiring.
14. Carburetor out of
adjustment.
15. Engine valves out of
adjustment.
Excessive
vibration
1. Worn, bent or loose blade.
2. Bent blade mandrel.
3. Loose/damaged part(s).
1. Replace blade.
Tighten blade bolt.
2. Contact our authorized
service center/department.
3. Tighten loose part(s).
Replace damaged parts.
Engine continues 1. Faulty operator-safety
to run when
presence control system.
operator leaves
seat with
attachment
clutch engaged
1. Check wiring, switches and
connections. If not corrected,
contact our authorized
service center/department.
Poor cut - uneven 1. Worn, bent or loose blade.
1. Replace blade. Tighten
blade bolt.
2. Level mower deck.
3. Clean underside of mower
housing.
4. Contact our authorized
service center/department.
5. Clean around mandrels to
open vent holes.
2. Mower deck not level.
3. Buildup of grass, leaves,
and trash under mower.
4. Bent blade mandrel.
5. Clogged mower deck vent
from build-up of grass,
leaves, and trash around
mandrels.
Mower blades will 1. Obstruction in clutch
not rotate
mechanism.
1. Remove obstruction.
29
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TROUBLESHOOTING CHART:
PROBLEM
CAUSE
CORRECTION
Mower blades will 2. Worn/damaged mower
not rotate (con’t)
drive belt.
3. Frozen idler pulley.
4. Frozen blade mandrel.
2. Replace mower drive belt.
3. Replace idler pulley.
4. Contact our authorized
service center/department.
Poor grass
discharge
1. Engine speed too slow.
1. Place throttle control in
“FAST” position.
2. Travel speed too fast.
2. Shift to slower speed.
3. Wet grass.
3. Allow grass to dry before
mowing.
4. Mower deck not level.
4. Level mower deck.
5. Low/uneven tire air pressure. 5. Check tires for proper air
pressure.
6. Worn, bent or loose blade.
6. Replace/sharpen blade.
Tighten blade bolt.
7. Buildup of grass, leaves and 7. Clean underside of mower
trash under mower.
housing.
8. Mower drive belt worn.
8. Replace mower drive belt.
9. Blades improperly installed. 9. Reinstall blades sharp edge
down.
10. Improper blades used.
10. Replace with blades listed
in this manual.
11. Clogged mower deck vent
11. Clean around mandrels to
holes from buildup of
open vent holes.
grass, leaves, and trash
around mandrels.
Headlight(s) not
working
(if so equipped)
1.
2.
3.
4.
Switch is “OFF”.
1.
Bulb(s) or lamp(s) burned out. 2.
Faulty light switch.
3.
Loose or damaged wiring.
4.
Turn switch “ON”.
Replace bulb(s) or lamp(s).
Check/replace light switch.
Check wiring and connections.
5. Replace fuse.
5. Blown fuse.
Battery will not
charge
1. Bad battery cell(s).
2. Poor cable connections.
3. Faulty regulator
(if so equipped).
4. Faulty alternator.
Loss of drive
1. Replace battery.
2. Check/clean all connections.
3. Replace regulator.
4. Replace alternator.
1. Freewheel control in
“disengaged” position.
2. Motion drive belt worn,
damaged, or broken.
3. Air trapped in transmission
during shipment or
servicing.
Engine “backfires” 1. Engine throttle control not
when turning
set at “SLOW”
engine
position for 30 seconds
“OFF”
before stopping engine.
1. Place freewheel control in
“engaged” position.
2. Replace motion drive belt.
3. Purge transmission.
1. Move throttle control to
“SLOW” position and allow
to idle for 30 seconds before
stopping engine.
30
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
SCHEMATIC
RED
BLACK
BATTERY
RED
A
RED
FUSE
AMMETER
(OPTIONAL)
M
STARTER
BLACK
WHITE
SOLENOID
RED
B
S
G
BLACK
L
M
CLUTCH / BRAKE
(PEDAL UP)
A1
A2
WHITE
SEAT SWITCH
(NOT OCCUPIED)
IGNITION
SWITCH
WHITE
BLACK
BLACK
BLACK
BLACK
HOUR
METER
ATT'MENT CLUTCH
(CLUTCH OFF)
GROUNDING
CONNECTOR
(OPTIONAL)
BLUE
SPARK
PLUG
GAP
(2 PLUGS ON
TWIN CYL. ENGINES)
IGNITION
UNIT
BLACK
FUEL
LINE
CHARGING SYSTEM OUTPUT
3 AMP DC @ 3600 RPM
FUEL SHUT-OFF SOLENOID
(IF SO EQUIPPED)
28 VOLTS AC MIN. @ 3600 RPM
(CHARGING SYSTEM DISCONNECTED)
RED
LIGHTING SYSTEM OUTPUT
5 AMP AC @ 3600 RPM
ORANGE
BLACK
DIODE
ALTERNATOR
14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF)
NOTE
YOUR TRACTOR IS
EQUIPPED WITH A SPECIAL
ALTERNATOR SYSTEM.
THE LIGHTS ARE NOT
CONNECTED TO THE
BATTERY, BUT HAVE THEIR
OWN ELECTRICAL SOURCE.
BECAUSE OF THIS, THE
BRIGHTNESS OF THE LIGHTS
WILL CHANGE WITH ENGINE
SPEED. AT IDLE THE LIGHTS
WILL DIM. AS THE ENGINE IS
SPEEDED UP, THE LIGHTS
WILL BECOME THEIR BRIGHTEST.
BLACK
BROWN
HEADLIGHTS
NON-REMOVABLE
CONNECTIONS
IGNITION SWITCH
POSITION
CIRCUIT
OFF
M+G+A1
RUN/LIGHT
B+A1
RUN
START
B+A1
B + S + A1
REMOVABLE
CONNECTIONS
“MAKE”
NONE
A2+L
NONE
NONE
WIRING INSULATED CLIPS
NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR
SERVICING OF UNIT, THEY SHOULD BE REPLACED TO
PROPERLY SECURE YOUR WIRING.
31
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
REPAIR PARTS
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
ELECTRICAL
22
21
42
24
41
43
27
27
40
26
27
27
25
16
16
33
30
D.C
.A
MP
ER
ES
52
29
45
8
28
27
55
2
1
90
32
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
ELECTRICAL
KEY PART
NO. NO.
DESCRIPTION
1
2
8
16
21
22
24
25
26
27
28
29
30
33
40
41
42
43
45
52
90
Battery
Bolt Hex Hd 1/4-20 Unc x 3/4
Battery Box
Switch Interlock Push-In
Harness Socket Light
Bulb, Light # 1156
Cable Battery
Cable Battery 6 Ga Red w/16 wire
Fuse
Nut Keps Hex 1/4-20 Unc
Cable Ground 6ga 12 black
Switch Plunger Nc Gray
Switch Ign
Key Ign Molded Generic
Harness Ign
Bolt Fin Hex 1/4-20 Unc x 1/2
Cover Terminal Red
Solenoid
Ammeter Rectangular
Protection Loop
Cover Terminal
144927
74760412
176689
176138
175688
4152J
4799J
146147
175158
73510400
4207J
121305X
175566
140401
179720
71110408
131563
178861
121433X
141940
180449
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
33
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
CHASSIS AND ENCLOSURES
29
212
17
159
30
24
18
28
58
12
24
26
53
51
25
26
31
25
52
5
5
209
209
9
11
208
209
219
208
54
20
23
207
26
64
219
3
13
35
3
3
33
1
10
142
3
145
37
37
3
3
208
3
142 3
2
35
14
206
34
3
14
chassis-shark.stlt_2
38
34
www.mymowerparts.com
26
55
57
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
CHASSIS AND ENCLOSURES
KEY PART
NO. NO.
DESCRIPTION
1
2
3
5
9
10
11
12
13
14
17
18
20
23
24
25
26
28
29
30
31
33
34
35
37
38
51
52
53
54
55
57
58
64
142
145
159
206
207
208
209
212
219
Chassis
Drawbar
Screw 3/8-16 x .75
Bumper Hood/Dash
Dash P/L
Bolt Carriage 3/8-16 x 1
Panel Dash Lh
Clip Tinnerman
Panel Dash Rh
Screw Thdrol 3/8-16 x 1-1/4
Hood W/Side Louvers
Bumper Hood Large
Plate Mtg Battery Fuel Tank
Bushing
Bolt Fin Hex 3/8-16 x 1 Gr 5
Washer 13/32 x 13/16 x 12 Ga
Nut Lock Hex W/Ins 3/8-16 Unc
Grille LT/PL
Lens
Fender Footrest STLT Pnt
Bracket Support Fender
Footrest Pnt Lh
Footrest Pnt Rh
Bolt Rdhd Sht Sqnk 3/8-16 x 3/4
Screw Thdrol 6/16-18 x 1/2 TYT
Bracket Asm. Pivot Mower Rear
Nut Lock Hex W/Ins 1/4-20
Washer 9/32 x 7/8 x 16 Ga.
Bracket Grille Lh
Screw Hex Wshd 8-18 x 7/8
Bracket Grille Rh
Bolt Hex 1/4-20 x 3/4
Duct Air
Dash Lower STLT
Plate Reinforcement STLT
Rod Pivot Chassis/Hood
Cupholder
Bolt Shoulder 5/16-18
Screw Thdrol 5/16-18 x 1/2
Screw Thdrol 3/8-16 x 1/2
Screw Hexwsh Thdr 3/8-16 x 3/4
Insert Lens Reflect
Screw 5/16-18 x 3/4
174619
176554
17060612
155272
168337X012
72140608
174996
145660
172106
17490608
144983X603
184921
180679
124028X
74780616
19131312
73800600
178987X428
155217X599
169470X603
136619
179716X603
179717X603
72110606
17490508
175710
73800400
19091416
145201
161464
145202
74780412
184460
154798
175702
156524
169473X428
170165
17670508
17670608
17000612
165919
17000512
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
35
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
GROUND DRIVE
51
57
89
63
212
69
70
197
161
169
159 158
59
65
162
61
198
164
32
150
168
163
10
50
41
14
21
202
64
56
83
81
116
66
82 165 156
48
38
166
8
151
51
27
49
35
39
30
47
62
120
36
52
34
52
16
36 35
37
32
95
53
28
30
26
26
16
29
16
84 27
22
77
26 25
15
19
24
55
199
200
250
77
26
1
250
71
96
78
74
75
76
73
16
36
www.mymowerparts.com
drive-hydro.stlt_34
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
GROUND DRIVE
KEY PART
NO. NO.
1
------
8
10
14
15
16
19
21
22
24
25
26
27
28
29
30
32
34
35
36
37
38
39
41
47
48
49
50
51
52
53
55
56
57
59
61
62
63
64
65
165619
76020416
10040400
74490544
73800500
73800600
140845
169498
73350600
106888X
19131316
76020412
175765
71673
169592
74760512
175578
120183X
19211616
1572H
179114
74760648
175556
127783
154407
123205X
72110612
73680600
73680500
105710X
105709X
17060620
140294
169691
17120614
8883R
175410
71170764
10040700
DESCRIPTION
Transaxle Hydro Gear 314-0510
(Order Parts From Transaxle
Manufacturer)
Rod Shift Hydro LT
Pin Cotter 1/8 x 1 CAD
Washer Lock Hvy Helical
Bolt, Hex FLGHD 5/16-18 Gr. 5
Nut Lock Hex W/Ins 5/16-18 Unc
Nut Lock Hex W/Wsh 3/8-16 Unc
Knob, Round 1/2-13
Rod, Brake Hydro
Nut
Spring, Brake Rod
Washer
Pin Cotter 1/8 x 3/4 CAD.
Rod, Parking Brake
Cap, Parking Brake
Bracket, Transaxle
Bolt Hex Hd 5/16-18 Unc x 3/4
Shaft, Foot Pedal
Bearing, Nylon
Washer
Pin, Roll
Pulley, Flat Composite
Bolt Fin Hex 3/8-16 x 3
Keeper, Belt Idler
Pulley, Idler, V-Groove
Bellcrank Clutch Grnd Drv STL
Retainer, Belt
Bolt Carr. SH 3/8-16 x 1-1/2 Gr. 5
Nut Crownlock 3/8-16 Unc
Nut Crownlock 5/16-18 Unc
Link, Clutch
Spring, Return, Clutch
Screw 3/8-16 x 1-1/4
V-Belt, Ground Drive
Keeper, Center Span
Screw 3/8-16 x .875
Cover, Pedal
Pulley, Engine
Bolt, Hex
Washer
KEY PART
NO. NO.
DESCRIPTION
66
69
70
71
73
74
75
76
77
78
81
82
83
84
89
95
96
116
120
150
151
156
158
159
161
162
163
164
165
166
168
169
197
198
199
200
202
212
250
Keeper Belt Engine
Screw
Guide Belt
Strap Torque Lh Hydro
Strap Torque Rh Hydro
Spacer, Axle
Washer 25/32 x 1-1/4 x 16 Gauge
E-Ring
Key, Square
Washer 25/32 x 1-5/8 x 16 Gauge
Shaft Asm. Cross Hydro
Spring Torsion T/A
Washer 17/32 x 3/4 x 16 Ga.
Link Transaxle
Console, Hydro
Control Asm Bypass Hydro
Retainer Spring 1" Zinc/Cad
Bolt Rdhd Sq Neck 3/8-16 x 1
Nut Lock Flg 3/8-16
Spacer Retainer
Washer 13/32 x 2 x 10 Ga.
Washer Srrted 5/16 ID x 1.125
Bracket Shift Mount
Hub Tapered Flange Shift Lt
Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr 5
Nut Crownlock 1/4-20 Unc
Bolt Hex Fin 1/4-20 Unc x 1 Gr 5
Washer 5/8 x .281 x 10 Ga
Bracket Pivot Lever
Screw 5/16-18 x 5/8
Bolt Shoulder 5/16-18 x .561
Plate Fastening Lt
Nyliner Snap-In 5/8" ID
Washer Nyl 7/8 ID x .105
Bolt Shoulder 5/16-18 Unc
Bolt Rdhd Sqnk 5/16-18 Unc x 1
Bolt RDHD 3/8-16 x 1-1/2 Gr 5
Nut Hex Flg Lock
Screw Thdrol. 3/8-16 x .75
154778
142432
134683
169183
169182
137057
121749X
12000001
123583X
121748X
165596
123782X
19171216
169594
169373X428
170201
4497H
72140608
73900600
175456
19133210
166002
165589
165494
72140406
73680400
74780416
19091010
165623
166880
165492
165580
169613
169593
169612
72140508
72110612
145212
17060612
NOTE: All component dimensions given in U.S.
inches 1 inch = 25.4 mm
37
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
STEERING ASSEMBLY
38
12
39
1
41
42
37
37
36
44
51
54
88
91
43
71
68
29
67
67
46
8
47
6
9
17
67
13
65
46
85
2
8
7
85
6
9
9
5
47
7
3
32
68
11
82
29
9
5
26
4
43
15
40
15
43
29
28
15
10
30
steering_pl.lt_42
38
www.mymowerparts.com
6
8
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
STEERING ASSEMBLY
KEY PART
NO. NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
15
17
26
28
29
30
32
36
37
38
39
40
41
42
43
44
46
47
51
54
65
67
68
71
82
85
88
91
Wheel Steering
Axle Asm Cast Iron LT
Spindle Asm LH
Spindle Asm RH
Bearing Race Thrust Harden
Washer 25/32 x 1-5/8 x 16 Ga
Washer 27/32 x 1-1/4 x 16 Ga
Ring Klip #t5304-75
Bearing Col. Strg.
Link Drag
Washer Lock Hvy Hlcl Spr 3/8
Nut Hex Jam Toplock 1/2-20 Unf
Spacer Brg. Axle Front
Nut Hex Flange Lock
Shaft Asm. Steering
Bushing Link Drag
Washer 13/32 x 7/8 x 16 Ga.
Screw 3/8-16 x .75
Pin Cotter 1/8 x 3/4
Rod Tie
Bushing Strg
Screw
Insert Cap Strg Wh Au
Washer
Lock nut
Adaptor Wheel Strg
Boot Steering Dash
Washer 25/32 x 1 1/4 x 16 Ga
Extension Steering Shaft
Cap Spindle Fr Top Blk
Fitting Grease
Nut Crownlock 1/4-28
Bolt Hex 1/4-28 Unf x 1-1/4 Gr. 8
Brace Axle
Bolt Rdhd Sq 3/8-16 Unc x 2-1/4
Axle, Brace
Steering Asm.
Bracket Susp. Chassis Front
Fastner Christmas Tree
Bolt Shoulder 7/16-20 Unc
Clip Steering
184704X428
175131
169840
169839
6266H
121748X
19272016
12000029
3366R
175121
10040600
73940800
136518
145212
180641
126847X
19131416
17060612
76020412
130465
155099
152927
159946X428
19182411
7810H
159945
145054X428
121749X
180640
121232X
183226
73540400
71130420
160367
72140618
169827
175146
169835
133835
175118
175553
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
39
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
ENGINE
2
8
1
3
14
13
38
25
26
6
81
5
17
17
72
16
32
44
46
33
37
31
45
33
40
41
112
23
29
4
OPTIONAL EQUIPMENT
Spark Arrester
KEY PART
NO. NO.
1
2
3
170771
17720408
--------
4
5
6
8
10
13
14
16
17
23
26
29
149723
160589
159955
171877
162797
165391
148456
11050600
17060624
169837
73920600
137180
engine-bs.twin_
KEY PART
NO. NO.
DESCRIPTION
31
32
33
37
38
40
41
44
45
46
62
72
81
112
Tank, Fuel
Cap Asm Fuel W/sym Vented
Clamp Hose Black
Line Fuel 20"
Plug Drain Oil Easy
Bushing Snap Nyl Blk Fuel Line
Stem Tank Fuel
Screw Hexwsh Thdrol 1/4-20 x 3/4
Screw Hexwsh Thdr 3/8-16 x 3/4
Washer 9/32 x 7/8 x 16 Ga
Washer Lock Hvy Hlcl Spr 5/16
Screw Hex Hd Cap 5/16-18 x 3/4
Nut Keps Hex 1/4-20 Unc
Bushing
DESCRIPTION
Control, Throttle
Screw Hex Thd Cut 1/4-20 x 1/2
Engine, Briggs Model 407777
(Order Parts From Engine Manufacturer)
Muffler, Asm. Twin Lo-Tone
Pipe Exhaust Intek 20 RH
Pipe Exhaust Intek 20 LH
Bolt 5/16-18 Unc x 3/4 w/Sems
Shield Browing B&S Untek II
Gasket Muffler
Tube Drain Oil Easy
Washer Lock Ext Tooth 3/8
Screw 3/8-16 x 1-1/2
Shield Brn/Dbr Guard
Nut Keps 3/8-24 unf
Kit Spark Arrestor (Flat Scrn)
40
180645
140527
123487X
137040
181654
124028X
139277
17670412
17000612
19091416
10040500
71070512
73510400
3645J
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
SEAT ASSEMBLY
1
8
8
9
14
9
7
7
10
5
6
22
21
2
24
5
16
25
15
11
4
13
17
3
12
seat_lt.knob_1
KEY PART
NO. NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
Seat
Bracket Pivot Seat 8 720
Bolt Fin Hex 3/8-16 Unc x 1
Washer 13/32 x 1 x 10 Ga
Clip Push-In
Nut Hex w/Ins. 3/8-16 Unc
Spring Seat Cprsn 2 250 Blk Zi
Screw 3/8-16 x 1.5
Washer 13/32 x 1 x 14 Ga.
Pan Seat
Knob Seat
Bracket Mounting Switch
140117
140551
71110616
19131610
145006
73800600
124181X
17000616
19131614
182493
166369
121246X
KEY PART
NO. NO.
DESCRIPTION
13
14
15
16
17
21
22
24
25
Bushing Snap Blk Nyl 50 Id
Bolt Rdhd Sqnk 1/4-20 x 1-1/2
Spacer Split 28x 88
Spring Cprsn
Nut Lock 1/4 Lge Flg Gr 5 Zinc
Bolt Shoulder 5/16-18 Unc
Nut Hex Lock W/Ins 5/16-18
Washer 17/32 x 1-3/16 x 12 Ga.
Bolt Shoulder 5/16-18 x 62
121248X
72050412
134300
121250X
123976X
171852
73800500
19171912
127018X
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
41
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
DECALS
11
3
16
7
10
20
1
6
5
18
14
KEY PART
NO. NO.
DESCRIPTION
1
3
5
7
8
9
10
11
14
Decal Oper
Decal Hood LH
Decal HP Engine
Decal Repl. Parts
Decal Deck "B" 42"
Decal Fender Logo
Decal Fender Danger E/F
Decal Ins Strg Whl
Decal V-Belt Schematic
156811
184970
170851
185440
179128
184944
156439
184943
160396
WHEELS & TIRES
1
2
5,8
7
4,10
3,9
6
11
KEY PART
NO. NO.
DESCRIPTION
16
20
---------
Decal Hood Rh
Decal Bat Dan/Psn
Decal By Pass
Pad Footrest LH
Pad Footrest RH
Decal Handle Lft Height Adjust
Decal Chassis
Decal Footrest
Manual Owner's (English)
Manual Owner's (Spanish)
184969
145005
169210
179768X428
179769X428
138311
184961
181249
185106
185107
KEY PART
NO. NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
--
Cap Valve Tire
Stem Valve
Tire F T 15 x 6 0 - 6 Service
Tube Front (Service Item Only)
Rim Asm 6"front Service
Fitting Grease (Front Wheel Only)
Bearing Flange (Front Wheel nly)
Rim Asm 8"rear Service
Tire R T 20 x 10-8 Service
Tube Rear (Service Item Only)
Cap Axle Blk 1 50 x 1 00
Sealant, Tire ( 10 oz. Tube)
59192
65139
106222X
59904
106732X417
278H
9040H
106108X417
122082X
7152J
104757X421
144334
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
wheel_1
42
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
LIFT ASSEMBLY
29
28
27
25 24
23
7
8
41
5
37
49
38
30
40
36
13
50
4
1
3
26
6
2
11
6
5
4
12
13
19
13
20
31
32
13
19
20
20
31
32
17 18 20
16
15
lift-rh.1pc.stlt_1
KEY PART
NO. NO.
DESCRIPTION
1
2
3
4
5
6
7
8
11
12
13
15
16
17
18
19
20
23
Wire Asm Inner/Sprg W/plunger LT
Shaft Asm Lift RH w/Inf
Pin Groove 1 500 Zinc
E Ring #5133-62
Washer 21/32 x 1 x 21 Ga
Bearing Nylon Blk 629 Id
Grip Handle
Button Plunger
Link Lift LH Fixed Length
Link Lift RH Fixed Length
Retainer Spring
Link Front
Nut Jam Hex 1/2-13 Unc
Trunnion
Nut Lock W/Wsh 1/2-13 Unc
Arm Suspension Rear
Retainer Spring
Nut Special
159460
159471
105767X
12000002
19211621
120183X
109413X
124526X
139865
139866
4939M
173288
73350800
175689
73800800
139868
163552
110807X
15
KEY PART
NO. NO.
DESCRIPTION
24
25
26
27
28
29
30
31
32
36
37
38
40
41
49
50
Washer 13/32 x 5/8 x 16 Ga
Spring 2-1/8"
Retainer Clip
Rod Adj Lift Zinc 7.49 Wrk Lg
Nut Hex Jam 3/8-16 Unc
Knob Inf 3/8-16 Unc Blk W/sym
Trunnion Infin Height
Bearing Pvt Lift
Nut Crownlock 3/8 - 24
Pointer Height Indicator
Plug Hole Blk 1.485/1.515 Dia.
Screw 5/16-18 x 1
Washer 11/32 x 1-1/2 10 Ga.
Indicator Height STLT
Nut Hex Flange Lock
Nut PUsh Phos & Oi
19131016
2876H
169484
126971X
73350600
138057
150233
169865
73540600
155097
123935X
17060516
19112410
155098
145212
110452X
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
43
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
MOWER DECK
158
67
157
68
40
37
36
40
156
153
151
155
152
143
153 154
159
46
144
45
150
40
37
145
44
184
59
56
53
52 55
106
103
102
105
105
48
147
148
54
142
104
103
146
33
32
31
102
30
34
104 106
101
21
132 91
182
21
94
1
147
95
2
132
21
142
116
183
21
23
113 111 114
25
2
117
26
2
119
16
118
15
14
20
28
27
29
18
3
4
18
149
114
13
5
24
112
2
6
118
11
19
42_deck_man-t-path_3
21
10
9
8
119
113
44
www.mymowerparts.com
117
116
For Parts Call K&T 606-678-9623 or 606-561-4983
TRACTOR - - MODEL NUMBER WA20H42STA PRODUCT NO. 954 56 83-35
MOWER DECK
KEY PART
NO. NO.
1
2
3
4
5
6
8
9
10
11
13
14
15
16
18
19
20
21
23
24
25
26
27
28
29
30
31
32
33
34
36
37
40
44
45
46
48
49
50
51
52
53
54
55
56
59
67
68
165892X421
72140506
138017
165460
4939M
178024
850857
10030600
140296
134149
138498
137645
128774
110485X
174493
72140505
132827
159770
73680500
177563
105304X
123713X
110452X
130968X428
19111016
131491
173984
129963
153535
178342
72110614
131494
19131316
73680600
140088
4497H
137729
133944
174284
131340
69180
139888
131845
178515
155046
165723
141043
106932X
144959
DESCRIPTION
Mower Deck Assembly, 42"
Bolt
Bracket Asm Fr. Sway Bar 3/42
Bracket Asm Deck 42" Sway Bar
Retainer Spring
Bar Sway Deck
Bolt 3/8-24 x 25 Gr. 8 patched
Washer, Lock
Washer, Hardened
Blade, Mulching 42”
Blade Mower 42” Hi-Lift
Shaft Assembly, Mandrel, Vented
Housing, Mandrel, Vented
Bearing, Ball, Mandrel
Stripper, Mandrel Deck
Bolt, Carriage 5/16-18 x 5/8
Bolt, Shoulder
Baffle, Vortex
Nut
Bracket, Deflector Mower 42"
Cap, Sleeve 80 x 112 Blk Mower
Spring, Torsion, Deflector 2 52
Nut, Push Phos & Oil
Shield, Deflector 42" Blk
Washer 11/32 x 5/8 x 16 Gauge
Rod, Hinge 42" 6 75 W/G
Screw Thdrol Washer Head
Washer, Spacer Mower Vented
Pulley, Mandrel
Nut, Toplock 9/16 Flange
Bolt
Pulley, Idler, Flat
Washer 13/32 x 13/16 x 16 Ga.
Nut
Guard, Mandrel, LH
Retainer
Screw, Thdrol 1/4-20 x 5/8 T
Washer, Hardened
Roller Assembly, Cam Follower
Bolt, Shoulder #10-24 Grade 5
Locknut
Bolt, Shoulder 5/16-18 Unc
Arm Assembly, Pad, Brake
Washer, Hardened
Arm, Idler
Spacer, Retainer
Guard TUV Idler
Knob
V-Belt, 42" Mower
KEY PART
NO. NO.
91
94
95
101
102
103
104
105
106
111
112
113
114
115
116
117
118
119
132
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
182
183
184
--
180532
132264
180533
136420
71081010
19061216
10071000
160793
2029J
179292
179293
17060510
73510500
72110505
4898H
165746
73930600
19121414
17000612
165890
157109
158634
165888
171977
131335
169022
165898
19091216
169670
169676
169674
169675
169671
169672
169669
17720408
72140614
179126
163552
19131410
130794
--
171491
DESCRIPTION
Bracket Asm Noseroller LH
Roller Nose 38 & 42
Bracket Asm Noseroller RH
Mulcher Cover
Screw
Washer, Flat
Washer, Lock
Latch Assembly
Nut, Weld
Bracket, Gauge, Wheel LH
Bracket, Gauge, Wheel RH
Screw 3/8-16 x .625
Nut, Keps 5/16 - 18 Unc
Bolt, Carriage 5/16-18 x 5/8
Bolt, Shoulder
Wheel, Gauge
Nut Centerlock 3/8-16
Washer 3/8 x 7/8 x 14 Ga.
Screw 3/8-16 x .75
Arm Spring Brake Mower
Bracket Arm Idler 42"
Keeper Belt 42" Clutch Cable
Pulley Idler Flat
Bolt Carriage Idler
Spring Extension
Spring Return Idler
Retainer Spring Yellow
Washer 9/32 x 3/4 x 16 Ga.
Bracket Clutch Cable
Clutch Cable 42"
Washer Flat 3/8" Type B
Spring Retainer
Spring Retention LVR CLTCH CAB
Spacer Clutch Cable
Rod Clutch Cable 3/8"
Screw Hex Thd Cut 1/4-20 x 5/8
Bolt Rdhd Sqn 3/8-16 Unc x 1-3/4
Rod Nose Roller
FRetainer Spring
Washer 13/32 x 7/8 x 10 Ga.
Mandrel Assembly (Includes
Housing, Shaft and Shaft Hard
ware Only-Pulley Not Included)
Replacement Mower, Complete
NOTE: All component dimensions given in U.S.inches
1 inch = 25.4 mm
45
www.mymowerparts.com
For Parts Call K&T 606-678-9623 or 606-561-4983
46
www.mymowerparts.com
47
www.mymowerparts.com
1. Fold this page along dotted line indicated above.
2. Hold page before you so that its left edge is vertically parallel to a tree
trunk or other upright structure.
3. Sight across the fold in the direction of hill slope you want to measure.
4. Compare the angle of the fold with the slope of the hill.
WARNING: To avoid serious injury, operate your tractor up and
down the face of slopes, never across the face. Do not mow
slopes greater than 15 degrees. Make turns gradually to prevent
tipping or loss of control. Exercise extreme caution when
changing direction on slopes.
15 DEGREES MAX.
ONLY RIDE UP AND DOWN HILL,
NOT ACROSS HILL
FOL
D AL
ONG
THIS
DOT
IS A
TED
15 D
LINE
EGR
EE S
LOP
E
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION
For Parts Call K&T 606-678-9623 or 606-561-4983
For Parts Call K&T 606-678-9623 or 606-561-4983
00273
www.mymowerparts.com