Scion 2006 xA Owner`s manual

SCION
xA
Preparation
2006 -
NOTE: Part number of this accessory may not be
the same as the part number shown.
Part Number: 08586-52973
Kit Contents
Item #
1
2
3
4
5
6
Quantity Reqd.
1
1
2
1
1
1
Description
Wire Harness
V3 Security ECU
Remote Control Transmitters
Piezo Buzzer
Status Monitor
Butyl Tape
Quantity Reqd.
1
3
1
10
25
1
2
1
1
Description
ECU Mounting Bracket
Large Foam Tape Strips (2 per.)
Small Foam Tape Strips (1 per.)
Large Wire Ties
Medium Wire Ties
Key Tag
Warning Labels
Owner's Manual
Warranty Card
Additional Items Required For Installation
Item #
Quantity Reqd.
Description
Conflicts
Note: Must not be installed in vehicles with factory Antitheft alarm.
Recommended Tools
Personal & Vehicle
Protection
(Optional)
Blankets, Part Boxes
Special Tools
Notes
Installation Tools
Notes
IADS #: ALL 02-016-03
CAD-E IADE P/N
ALL 02-016-01
Phillips Head Screwdriver
Flat Blade Screwdriver
Socket
Socket Extension
Nylon Panel Removal Tool
#2, screwdriver or tip
Small, Jeweler's
10mm
3"
e.g. Panel Pry Tool #1
Wrench
Side Cutters
Torque Wrench
10mm
Issue: C
05/24/05
Special Chemicals
Cleaner
Glass Cleaner
Notes
3MTM Prep Solvent-70
Household Windex
General Applicability
Recommended Sequence of Application
Item #
1
2
3
4
Accessory
TVIP
Satellite
Receiver
Audio
Door Sill
Applique
*Mandatory
Vehicle Service Parts (may be required for reassembly)
Item #
1
2
3
Quantity Reqd.
Description
Legend
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
Notes
Safety Glasses
Safety Gloves
Vehicle Protection
Wiring Terminal Tool
Striker Tool (PPO only)
Pneumatic/Electric Wrench
Note: SCION xA with power door lock, only.
Hardware Bag Contents
Item #
1
2
3
4
5
6
7
8
9
SECURITY WITH RKE (V3)
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
Toyota SST # 00002-06001-01
4.1 N·m (36 lbf·in)
Page 1 of 22 pages
DIO
SCION
Procedure
xA
2006 -
SECURITY WITH RKE (V3)
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:-- Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
-- Safety (eye protection, rechecking torque procedure, etc.).
-- Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
-- Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
Please see your Toyota dealer for a copy of this document.
1. Vehicle Disassembly.
(a) For automatic equipped vehicles, place the
shifter in low gear and set the parking brake
prior to disconnecting the battery.
Negative
Battery
Cable
10mm Wrench
(b) Remove the negative battery cable. (Fig. 1-1)
(1) Protect the fender before starting.
Battery
Fig. 1-1
(2) Do not touch the positive terminal with
any tool when removing the cable.
(c) Using a Nylon Panel Removal Tool, remove
the driver's side step cover. (Fig. 1-2)
Nylon Panel Removal Tool
Float Clip
(1) Cover the floor and seats before starting.
(2) Remove the float clip first to prevent
damaging the panel.
(d) Remove the driver's side cowl cover.
(Fig. 1-3)
Step Cover
(1) Remove the nut securing the cowl cover.
Fig. 1-2
Nut
Cowl Cover
Fig. 1-3
Issue: C
05/24/05
Page 2 of 22 pages
DIO
SCION
Procedure
xA
2006 -
SECURITY WITH RKE (V3)
(e) Remove the driver's side fuse cover.
(Fig. 1-4)
Knockout Cover
(1) Remove and discard the knockout cover,
located at the third space from the left.
(f) Remove the two screws securing the lower
steering column cover behind the steering
wheel. (Fig. 1-5)
Fuse Cover
(1) Insert the key into the ignition switch and
turn it to ON to unlock the steering
wheel.
Fig. 1-4
Phillips Screwdriver
(2) Turn the steering wheel left and right to
gain access to the screws.
(g) Remove the lower steering column cover.
(Fig. 1-6)
(1) Remove the bottom screw securing the
cover.
Screw
Screw
Fig. 1-5
(h) Using the Nylon Panel Removal Tool,
remove the center cluster side covers.
(Fig. 1-7)
Phillips Screwdriver
STOP
(1) Use caution when prying the center
cluster side covers to avoid damage.
Screw
Column Cover
Fig. 1-6
Nylon Panel Removal Tool
STOP
Side Cover
Fig. 1-7
Issue: C
05/24/05
Page 3 of 22 pages
DIO
SCION
xA
Procedure
2006 -
SECURITY WITH RKE (V3)
(i) Using the Nylon Panel Removal Tool,
remove the center cluster under panel.
(Fig. 1-8)
Nylon Panel Removal Tool
(1) For manual transmission place in fourth
gear.
(j) Remove the center cluster under cover.
(Fig. 1-9)
Under Panel
Fig. 1-8
(1) Remove the two clips securing the under
cover.
(k) Using the Nylon Panel Removal Tool,
remove the passenger's side step cover.
(Fig. 1-10)
Nylon Panel Removal Tool
(1) Cover the floor and seats before starting.
Clip
Clip
(l) Remove the passenger's side cowl cover.
(Fig. 1-11)
Under Cover
Fig. 1-9
(2) Remove the float clip first to prevent
damaging the panel.
(1) Remove the nut securing the cowl cover.
Nylon Panel Removal Tool
Float Clip
Step Cover
Fig. 1-10
Nut
Cowl Cover
Fig. 1-11
Issue: C
05/24/05
Page 4 of 22 pages
DIO
SCION
xA
Procedure
2006 -
SECURITY WITH RKE (V3)
(m)Remove the glove box. (Fig. 1-12)
2. Piezo Buzzer Installation.
(a) Using one large foam tape and one large wire
tie, secure the Piezo Buzzer to the vehicle's
harness near the vehicle's clip. (Fig. 2-1)
(1) Do not cover the opening of the Buzzer
with the foam tape.
Glove Box
Fig. 1-12
(2) Ensure the Buzzer opening is facing
downward.
Side Cutter
Large Foam Tape
(b) Locate the gray 2P connector near the vehicle
grommet. (Fig. 2-2)
Piezo Buzzer
(1) Remove and discard the cap from the
gray 2P connector.
Fig. 2-1
Vehicle's Clip
Large Wire Tie
(1) Verify the connectors are plugged in
securely.
Cap
2P (Gray)
(c) Plug in the Piezo Buzzer harness gray 2P
connector to the vehicle harness gray 2P
connector. (Fig. 2-3)
(d) Using one large foam tape and one large wire
tie, secure the gray 2P connectors to the
vehicle harness. (Fig. 2-3)
Piezo Buzzer
Fig. 2-2
Side Cutter
2P (Gray)
Large Wire Tie
Piezo Buzzer
Fig. 2-3
Issue: C
Large Foam Tape
05/24/05
Page 5 of 22 pages
DIO
SCION
xA
Procedure
2006 -
3. V3 Harness Installation. (Driver Area)
Small Flat Blade Screwdriver
Tape
3P (White)
18P (White)
Diode
(a) Locate the vehicle harness' white 3P diode
connector and remove the tape securing the
white 3P diode connector to the driver's side
cowl area. (Fig. 3-1)
(b) Locate and disconnect the white 13P and 18P
connectors from the driver's side cowl area.
(Fig. 3-1)
13P (White)
Fig. 3-1
Small Flat Blade Screwdriver, Jeweler's Screwdriver
Retainer
(c) Using a small flat blade screwdriver, remove
the diode from the white 3P diode connector.
(Fig. 3-1)
(1) Do not discard the diode.
(d) Using a small flat blade screwdriver, lift up
the terminal retainer on the white 3P diode
connector. (Fig. 3-2)
Vehicle
Harness'
RED Wire
3P (White)
Fig. 3-2
Vehicle Harness'
RED Wire
SECURITY WITH RKE (V3)
V3 Harness' RED Wire
V3 Harness' 1P
(e) Locate the RED wire in the right terminal
space. Using a jeweler's screwdriver, release
and pull out the RED wire. (Fig. 3-2)
(f) Insert the wire at the end of the V3 harness'
RED wire into the right terminal space of the
vehicle harness' white diode 3P connector.
(Fig. 3-3)
(1) Verify the correct opening is chosen.
(2) Verify the terminal is inserted and seated
properly.
(3) Close the retainer.
Fig. 3-3
3P (White)
(4) The terminal should not come out when
pulled lightly from the back. If the
terminal comes off, then push it in more
securely.
Small Flat Blade Screwdriver
1P (Female)
Retainer
(h) Using a small flat blade screwdriver, lift up
the terminal retainer on the back of the empty
1P connector. (Fig. 3-4)
1P (Male)
V3 Harness
Fig. 3-4
Issue: C
(g) Disconnect the empty 1P female connector
plugged into the V3 harness' 1P male
connector. (Fig. 3-4)
05/24/05
Page 6 of 22 pages
DIO
SCION
xA
Procedure
Vehicle Harness'
RED Wire
2006 -
(i) Insert the terminal at the end of the vehicle
harness' RED wire into the female empty 1P
connector. (Fig. 3-5)
V3 Harness' RED Wire
1P (Male)
(1) Verify the correct opening is chosen.
(2) Verify the terminal is inserted and seated
properly.
1P (Female)
Fig. 3-5
SECURITY WITH RKE (V3)
(3) Close the retainer.
Retainer
3P (White)
V3 Harness
3P (White)
Diode
V3 Harness
18P (White)
(j) Plug in the V3 harness' white 1P male
connector into the V3 harness' white 1P
female connector. (Fig. 3-6)
(1) Verify connectors are plugged in
securely.
1P (White)
Fig. 3-6
(4) The terminal should not come out when
pulled lightly from the back. If the
terminal comes off, then push it in more
securely.
(k) Plug in the V3 harness' white 13P connectors
between the driver's side cowl area and the
vehicle harness' 13P connector. (Fig. 3-6)
13P (White)
Side Cutter
(1) Verify connectors are plugged in securely.
1P (White)
3P (White)
Medium Wire
Ties (x2)
18P (White)
Large Wire Tie
Side Cutter
(l) Plug in the V3 harness' white 18P connectors
between the driver's side cowl area and the
vehicle harness' 18P connector. (Fig. 3-6)
(1) Verify connectors are plugged in securely.
13P (White)
Fig. 3-7
(2) Refit the diode to the vehicle harness' 3P
connector.
V3 Harness
Relays (x2)
(m)Secure the vehicle harness' white 3P diode
connector and the V3 Harness' white 1P
connector to the vehicle harness using one
medium wire tie. (Fig. 3-7)
(n) Secure the 13P connectors and the V3
harness to the connector block with one large
wire tie. (Fig. 3-7)
(1) Arrange and secure the 13P connectors
under the connector block as shown.
(o) Secure the V3 harness to the vehicle harness
with one medium wire tie. (Fig. 3-7)
Fig. 3-8
Issue: C
Large Wire Ties (x2)
05/24/05
(p) Route and attach the V3 harness' relays to the
vehicle harness with two large wire ties.
(Fig. 3-8)
Page 7 of 22 pages
DIO
SCION
xA
Procedure
9P (White)
2006 13P (White)
SECURITY WITH RKE (V3)
(q) Locate and disconnect the white 9P
connector and white 13P connector from the
back side of the driver's side J/B. (Fig. 3-9)
(r) Plug in the V3 harness' white 9P connectors
between the driver's side J/B and the vehicle
harness' 9P connector. (Fig. 3-10)
J/B
V3 Harness
J/B Back
Side View
Fig. 3-9
13P (White)
Side Cutter
9P (White)
(1) Verify the connectors are plugged in
securely.
(s) Plug in the V3 harness' white 13P connectors
between the driver's side J/B and the vehicle
harness' 13P connector. (Fig. 3-10)
(1) Verify the connectors are plugged in
securely.
J/B
V3 Harness
Back Side View
Back Side View
4. V3 Harness Installation. (Steering Area)
9P (White)
Large
Wire Tie
13P (White)
Large Wire Tie
13P (White)
J/B
(t) Secure the 9P connectors and 13P connectors
to the vehicle harness with two large wire
ties. (Fig. 3-10)
(a) Route the V3 harness toward the lower part
of steering wheel. (Fig. 4-1)
(b) Locate and disconnect the white 6P
connector from the lower part of steering
wheel. (Fig. 4-1)
Fig. 3-10
V3 Harness
6P (White)
Fig. 4-1
Issue: C
05/24/05
Page 8 of 22 pages
DIO
SCION
xA
Procedure
2006 Medium Wire Tie
Side Cutter
Large Wire Tie
V3 Harness
6P (White)
12P
SECURITY WITH RKE (V3)
(c) Plug in the V3 harness' white 6P connectors
between the vehicle harness' white 6P
connector and the lower part of steering
wheel. (Fig. 4-2)
(1) Verify the connectors are plugged in
securely.
(d) Secure the 6P connectors and the V3 harness
to the vehicle harness with one large wire tie.
(Fig. 4-2)
Fig. 4-2
(e) Secure the V3 harness to the vehicle harness
with one medium wire tie. (Fig. 4-2)
(f) Route the V3 harness toward the right side of
steering wheel. (Fig. 4-3)
(g) Locate and disconnect the black 12P
connector from the steering wheel area.
(Fig. 4-3)
12P (Black)
V3 Harness
Fig. 4-3
(h) Plug in the V3 harness' 12P connectors
between the vehicle harness' 12P connector
and the steering wheel area. (Fig. 4-4)
Side Cutter
Medium Wire Tie
(1) Verify the connectors are plugged in
securely.
V3 Harness
12P
Fig. 4-4
(i) Secure the V3 harness' 12P connectors to the
vehicle harness with one medium wire tie.
(Fig. 4-4)
(j) Route and secure the V3 harness to the
vehicle harness with one medium wire tie
below the steering column. (Fig. 4-5)
Side Cutter
Medium Wire Tie
V3 Harness
Fig. 4-5
Issue: C
05/24/05
Page 9 of 22 pages
DIO
SCION
xA
Procedure
2006 -
SECURITY WITH RKE (V3)
(k) Route and secure the V3 harness with the
black 4P connector to the vehicle harness
with two medium wire ties to the left of the
steering column. (Fig. 4-6)
Side Cutter
Medium Wire Tie
(1) Ensure that these wire ties do NOT
secure the fog light switch harness.
Fog Light Wire
Medium Wire Tie
5. Status Monitor Installation.
Fig. 4-6
V3 Harness
Side Cutter
(a) Connect the V3 harness' black 4P connector
to the status monitor. (Fig. 5-1)
(1) Verify connectors are plugged in
securely.
Medium Wire Tie
4P (Black)
(b) Insert the status monitor into the knockout
opening in the dash cover. (Fig. 5-1)
Status Monitor
(1) Verify the status monitor sits firmly in
the cover.
Fig. 5-1
Status Monitor
Large Foam Tape
(c) Secure the V3 harness to the vehicle harness
with one medium wire tie. (Fig. 5-1)
6. V3 Wire Harness Installation. (Continued)
(a) Locate the vehicle's brace in the driver's side
behind the center cluster. Attach one large
foam tape to the brace. (Fig. 6-1)
V3 Harness
Vehicle's Brace
(1) Verify the edge of the brace is covered.
(b) Locate the vehicle's brace in the driver's side
behind the center cluster. Attach one large
foam tape to the brace. (Fig. 6-2)
Fig. 6-1
Side Cutter
(1) Attach tape to both ends of the bracket.
Large Foam Tape
(2) Verify the edge of the brace is covered.
Vehicle's Brace
Fig. 6-2
Issue: C
05/24/05
Page 10 of 22 pages
DIO
SCION
xA
Procedure
2006 -
Side Cutter
V3 Harness
Medium
Wire Ties (x2)
Fig. 6-3
SECURITY WITH RKE (V3)
(c) Route and secure the V3 harness to the
vehicle harness with two medium wire ties
behind the driver's center cluster area.
(Fig. 6-3)
(d) Route and secure the V3 harness to the
vehicle's bracket with one medium wire tie
behind the center cluster. (Fig. 6-4)
(1) Pass the wire tie through the vehicle
bracket's hole.
(e) Route and secure the V3 harness to the
vehicle harness with one medium wire tie in
the glove box area. (Fig. 6-5)
Side Cutter
(f) Locate the vehicle harness' white 1P
connector in the glove box area. Remove the
tape from the connector. (Fig. 6-6)
V3 Harness
8P, 12P,
22P
Fig. 6-4
Side Cutter
Medium Wire Tie
1P (White)
V3Harness
Fig. 6-5
Vehicle's 1P (White)
Tape
1P (White)
V3 Harness
Fig. 6-6
Issue: C
05/24/05
Page 11 of 22 pages
DIO
SCION
xA
Procedure
2006 -
SECURITY WITH RKE (V3)
(g) Plug in the V3 harness' white 1P connector to
the vehicle harness' white 1P connector.
(Fig. 6-7)
Side Cutter
1P (White)
Medium Wire
Ties (x3)
V3 Harness
Fig. 6-7
Large Wire Ties (x2)
Side Cutter
(1) Verify the connectors are plugged in
securely.
(h) Secure the 1P connectors to the vehicle
harness with one medium wire tie. (Fig. 6-7)
(i) Secure the V3 harness to the vehicle harness
with two medium wire ties. (Fig. 6-7)
(j) Route and secure the V3 harness to the
reinforcement with two large wire ties.
(Fig. 6-8)
Reinforcement
V3 Harness
(k) Route and secure the V3 harness to the
vehicle harness with three medium wire ties
above the passenger side cowl area.
(Fig. 6-8)
Medium
Wire Ties
(x3)
Fig. 6-8
(l) Locate and disconnect the white 14P
connector from the passenger side cowl area.
(Fig. 6-9)
Side Cutter
14P (White)
V3 Harness
Fig. 6-9
14P (White)
Side Cutter
V3 Harness
(m)Plug in the V3 harness' white 14P connectors
between the vehicle harness' white 14P
connector and the passenger side cowl area.
(Fig. 6-10)
(1) Verify the connectors are plugged in
securely.
(n) Secure the 14P connectors to the vehicle
harness with one medium wire tie.
(Fig. 6-10)
Medium Wire Tie
Fig. 6-10
Issue: C
05/24/05
14P (White)
Page 12 of 22 pages
DIO
SCION
xA
Procedure
2006 -
SECURITY WITH RKE (V3)
7. V3 ECU Preparation and Installation.
Small Flat Blade Screwdriver
(a) Turn the adjustment screw on the V3 ECU to
the "6" position. (Fig. 7-1)
V3 ECU
(b) Insert the ECU mounting bracket into the
indicated bracket slot on the V3 ECU.
(Fig. 7-2)
(1) Insert the mounting bracket into the
correct slot; you have only one chance to
install it properly.
Fig. 7-1
ECU Mounting
Bracket
V3 ECU
(c) Apply two large foam tapes to the V3 ECU
as shown. (Fig. 7-3)
(d) Locate and remove the bolt securing the airconditioner unit in the glove box area.
(Fig. 7-4)
(1) Do not discard the bolt.
Fig. 7-2
(e) Apply the butyl tape to the air-conditioner
unit as shown. (Fig. 7-4)
Large Foam Tape
V3 ECU
Fig. 7-3
Large Foam Tape
10mm Socket
Air-Conditioner Unit
Butyl Tape
Bolt
Fig. 7-4
Issue: C
05/24/05
Page 13 of 22 pages
DIO
SCION
xA
Procedure
2006 -
SECURITY WITH RKE (V3)
(f) Connect the V3 ECU connectors (8P, 12P,
22P) to the V3 ECU. (Fig. 7-5)
V3 ECU
V3 Harness
(1) Verify the connectors are plugged in
securely.
(g) Mount the V3 ECU to the glove box area
with the vehicles' bolt. (Fig. 7-6)
(1) Verify the bolt is tightened securely.
Fig. 7-5
8P, 12P, 22P
(2) Verify the V3 harness does not droop
downward.
10mm Socket
8. Antenna Wire Installation.
Vehicle's Bolt
V3 ECU
(a) Using a small foam tape, secure the GRAY
Antenna wire to the inside surface of the
upper dash cover as shown. (Fig. 8-1)
9. Warning Label and Key Tag Installation.
Fig. 7-6
(a) Using household Windex, clean the inside
surface of the front door windows.
V3 Harness
Small Foam Tape
(1) Use a piece of clear adhesive tape to lift
the labels off of their protective backing
sheet.
Antenna Wire
(Gray)
V3 ECU
Fig. 8-1
Lineup with
Bottom of
Window Etching
(b) Place the warning label on the inside surface
of the front door's windows as shown.
(Fig. 9-1)
Warning
Label
10mm
(2) Do not touch the adhesive surface of the
warning labels.
(3) Line up the labels properly and place on
the glass once; do not use a label that was
pulled off the glass.
Fig. 9-1
Issue: C
05/24/05
Page 14 of 22 pages
DIO
SCION
xA
Procedure
2006 -
SECURITY WITH RKE (V3)
(4) Attach the key tag supplied in the kit to
the remote control's ring. (Fig. 9-2)
Remote Control
10. Completing the Installation.
Key
Ring
(a) Complete the reassembly of the vehicle.
(1) Reconnect any disconnected connectors.
Fig. 9-2
(2) Verify the panels fit together properly
with no uneven gaps between them.
Key Tag
Torque Wrench, 10mm Socket
(b) Clean up and remove any trash.
45 deg.
(c) Reconnect the vehicle's negative battery
cable. (Fig. 10-1)
(1) Position the negative terminal to the
battery as shown (~45 deg.).
(2) Tighten the nut to 4.1 N-m (36 lbf-in).
Battery
Fig. 10-1
Negative
Battery
Cable
(3) Do not touch the positive terminal with
any tool when replacing the cable.
(d) Reset the power windows.
(1) Turn the ignition key to "ON."
(2) Press the power button of each door to
lower the windows halfway.
(3) Press the buttons until the windows close,
and then hold the switches up for one (1)
additional second (minimum.)
(e) Reset the power moon roof (if equipped).
(1) Press and hold the moon roof button until
the moon roof closes. Hold for an
additional two (2) seconds.
(f) Place the owner's manual and warranty card
(left in their protective bags) in the glove
box.
Issue: C
05/24/05
Page 15 of 22 pages
DIO
SCION
xA
2006 -
SECURITY WITH RKE (V3)
Checklist - these points MUST be checked to ensure a quality installation.
Check:
Look For:
Accessory Function Checks
Fit appropriate fuse before beginning.
Press and release the remote control's lock
1.
The tail and marker lights flash once.
The buzzer chirps once.
button to start the system's arming process.
All doors lock.
The Status Monitor's LED lights up.
2.
Wait 30 seconds.
After 30 seconds, the LED starts
flashing; the system is now armed.
Press and release the remote control's
3.
The tail and marker lights flash twice.
The buzzer chirps twice.
unlock button to disarm the system.
The interior lights turn on for thirty
seconds.
The driver's door unlocks.
The Status Monitor's LED stops
flashing.
Press and release the remote control's
4.
The tail and marker lights flash twice.
The buzzer chirps twice.
unlock button again within 3 seconds of
All remaining doors unlock.
disarming the system.
Open and close the driver's door.
Arm and disarm the system with the remote
5.
The doors automatically relock.
The system automatically starts the
again, then wait 30 seconds.
arming process.
Press and release the remote control's
6.
Refer to Step 3.
7.
The buzzer sounds continuously for 5
unlock button again to stop the arming
process.
Open the driver's door, then press and
seconds.
release the remote control's lock button.
8.
Close the driver's door.
Issue: C
05/24/05
Page 16 of 22 pages
The buzzer stops sounding.
DIO
SCION
xA
2006 -
SECURITY WITH RKE (V3)
Checklist - these points MUST be checked to ensure a quality installation.
Check:
Look For:
Press and release the remote control's panic
9.
button to trigger the panic alarm.
The horn sounds repeatedly.
The interior lights turn on.
The headlights flash repeatedly.
The tail and marker lights flash
repeatedly.
The LED lights up.
Press and release the remote control's panic
button again to stop the panic alarm.
10. The horn stops sounding.
All the lights stop flashing and/ or turn
off.
Sit in the driver's seat and make sure all
doors are closed.
Insert the key into the ignition switch and
11. All doors lock.
turn it to "ON."
Roll down all the windows.
Turn the key back to "LOCK."
12. All doors unlock.
Remove the key and exit the vehicle.
Insert the key into the driver's door key
cylinder and turn it toward the front of the
13. All doors lock.
The LED lights up.
vehicle to start the arming process.
Wait 30 seconds.
14. After 30 seconds, the LED starts
flashing; the system is now armed.
Reach inside and manually unlock the
driver's door.
15. The driver's door automatically
relocks.
The horn sounds repeatedly.
The interior lights turn on.
The headlights flash repeatedly.
The tail and marker lights flash
repeatedly.
The LED lights up.
Issue: C
05/24/05
Page 17 of 22 pages
DIO
SCION
xA
2006 -
SECURITY WITH RKE (V3)
Checklist - these points MUST be checked to ensure a quality installation.
Check:
Look For:
Manually unlock the driver's door again and
16. The driver's door lock attempts to lock
hold it unlocked, open the door, then sit in
repeatedly.
the driver's seat.
The horn continues to sound
repeatedly.
The interior lights remain on.
The headlights, tail lights and marker
lights continue flashing.
The LED remains on.
Insert the key into the ignition switch and
turn it to "START" to stop the alarm.
17. The horn stops sounding.
All the lights stop flashing and/ or turn
off.
The Status Monitor LED turns off.
The starter cranks and the engine
starts.
Turn the key back to "LOCK," remove
it, and then exit the vehicle.
With the door open, press the lock switch
on the door to lock the doors, and then
18. All doors lock.
The Status Monitor's LED lights up.
close the door to start the system's arming
process.
19. After 30 seconds, the LED starts
Wait 30 seconds.
flashing; the system is now armed.
20. The front passenger's door
Reach inside and manually unlock the front
automatically relocks.
passenger's door to trigger an alarm.
The horn sounds repeatedly.
The interior lights turn on.
The headlights flash repeatedly.
The tail and marker lights flash
repeatedly.
The LED lights up.
Issue: C
05/24/05
Page 18 of 22 pages
DIO
SCION
xA
2006 -
SECURITY WITH RKE (V3)
Checklist - these points MUST be checked to ensure a quality installation.
Check:
Look For:
Press and release the remote control's
21. The horn stops sounding.
unlock button to stop the alarm.
All the lights stop flashing and/ or turn
off.
The Status Monitor's LED turns off.
Press and release the remote control's lock
22. Refer to Steps 1 and 2.
button to start the system's arming process,
and then wait 30 seconds until the system is
armed.
Unlock and open one of the rear passenger
Refer to Step 9.
doors to trigger an alarm.
Repeat the above steps with the other rear
24. Refer to Steps 22 and 23.
passenger and back door (if equipped).
Roll up all windows, remove the key and
exit the vehicle.
Press and release the remote control's lock
25. Refer to Step 1.
button to start the system's arming process.
Wait 30 seconds.
26. After 30 seconds, LED starts flashing;
the system is now armed.
Perform the following check in a
temperature-controlled environment
(50° - 90° F.)
Using the striker tool, tap the center of the
27. The horn sounds repeatedly.
driver's door window to trigger the "warn
The headlights flash repeatedly.
away" alarm.
The tail and marker lights flash
repeatedly.
The LED lights up.
Issue: C
05/24/05
Page 19 of 22 pages
DIO
SCION
xA
2006 -
SECURITY WITH RKE (V3)
Checklist - these points MUST be checked to ensure a quality installation.
Check:
Look For:
NOTE: Adjust as necessary by increasing
the GBS setting to the next level if the
alarm does not trigger during the functional
verifications.
NOTE: If you do not disarm the system,
the alarm will last 20 seconds. It is not
necessary to check the alarm duration.
Insert the key into the driver's door key
28. The horn stops sounding.
cylinder and turn it toward the back of the
All the lights stop flashing and/or turn off.
vehicle to stop the alarm.
The status monitor's LED turns off.
Vehicle Function Checks
Head Lights
Functioning Head Lights
High Beams
Functioning High Beams
Turn Signal Lights
Functioning Turn Signal Lights
Tail Lights
Functioning Tail Lights
Stop Lights
Functioning Stop Lights
Backup Lights
Functioning Backup Lights
Hazard Lights
Functioning Hazard Lights
Marker Lights
Functioning Marker Lights
Dome/Courtesy Lights
Functioning Dome/Courtesy Lights
Panel/Switch Illumination
Functioning Controls/Illumination
Accessory Controls/Illumination (if
Functioning Accessory
equipped)
Key Sensor Buzzer
Functioning Key Sensor
Fog Lights (if equipped)
Functioning Fog Lights
Daytime Running Lights (if equipped)
Functioning DR Lights
Issue: C
05/24/05
Page 20 of 22 pages
DIO
SCION
xA
2006 -
SECURITY WITH RKE (V3)
Checklist - these points MUST be checked to ensure a quality installation.
Check:
Look For:
Trunk/Tailgate/Bed Lights (if equipped)
Functioning Lights
Glove Box Light (if equipped)
Functioning Glove Box Light
Cruise Control Light (if equipped)
Functioning Cruise Control Light
Seat Belt Warning Light
Functioning Seatbelt Warning Light. If the
warning light remains "ON", it may
indicate a system malfunction.
Functioning Air Bag Warning Light. If the
Air Bag Warning Light
warning light remains "ON," it may
indicate a system malfunction.
Functioning ABS Light. If the warning light
ABS Light (if equipped)
remains "ON," it may indicate a system
malfunction.
Functioning Lamp Failure Light. If the
Lamp Failure Sensor (if equipped)
warning light remains "ON," it may
indicate a system malfunction.
Track/Skid Control Light (if equipped)
Functional Track/VSC Light. If the warning
light remains "ON," it may indicate a
system malfunction.
HVAC
Functioning HVAC Controls
Power Locks (if equipped)
Functioning Power Locks
Power Windows (if equipped)
Functioning Power Windows
Power Seats (if equipped)
Functioning Power Seats
Power Sunroof (if equipped)
Functioning Sunroof
Horn
Functioning Horn
Gauges
Functioning Gauges
Front Wiper/Washer
Functioning Front Wiper/Washer
Issue: C
05/24/05
Page 21 of 22 pages
DIO
SCION
xA
2006 -
SECURITY WITH RKE (V3)
Checklist - these points MUST be checked to ensure a quality installation.
Check:
Look For:
Rear Wiper/Washer (if equipped)
Functioning Rear Wiper/Washer
Clock (if equipped)
Functioning Clock
Accessory Power Socket (if equipped)
Functioning Power Socket
Starter
Functioning Starter
Audio/Video (if equipped)
Functioning Audio/Video
Power Sliding Door (if equipped)
Functioning Power Sliding Door
Convenience Memory Settings (if
Functioning Memory Settings
equipped)
Heated Seats (if equipped)
Functioning Heated Seats
Massage Seats (if equipped)
Functioning Massage Seats
Rear Window Defogger (if equipped)
Functioning Rear Window Defogger
Power Side Mirrors (if equipped)
Functioning Power Side Mirrors
Side Mirror Defogger (if equipped)
Functioning Side Mirror Defogger
Front Windshield Defogger (if equipped)
Functioning Front Windshield Defogger
Navigation System (if equipped)
Functioning Navigation System
Power Back Door (if equipped)
Functioning Power Back Door
Remove the appropriate fuse after
checks are completed.
Issue: C
05/24/05
Page 22 of 22 pages
DIO