Craftsman 315.114840 Operator`s manual

'S MANUAL
i
1
19.2 VOLT HAMMER DRILL
1/2 in. Variable Speed
Model No.
31 5.114840
WARNING:
To reduce the risk of injury,
the user must read and understand the
operator's manual before using this
product.
Customer
HeUp Line: 1-800-932-3188
Sears, Roebuck
and Co., 3333 Bevedy Rd., Hoffman
Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com!craftsman
983000-487
8-04
Save this manual
for future
reference
ONE YEAR FULL WARRANTY
ON CRAFTSMAN
TOOL
(f th(s Craftsman too( fails to g(ve comp(ete satisfact(on within one year from date of purchase, RETURN (T TO THE
NEAREST SEARS STORE OR SEARS PARTS & REPAIR CENTER (N THE UNITED STATES, and Sears w(U repa(r (t,
free of charge.
(f this Craftsman too( is used for commercial
purchase.
or rental purposes, th(s warranty applies for only 90 days from the date of
This warranty gives you spec(fic (ega( rights, and you may also have other rights which vary from state to state.
Sears, Roebuck
and 0o., Dept. 817WA, Noffrnan Estates, (L 60179
This too( has many features for making its use more p(easant and enjoyab(e. Safety, performance, and dependability
have been given top priority in the design of th(s product making it easy to maintain and operate.
_
WARNING!READANDUNDERSTAND
ALL
iNSTRUCTiONS.
Failureto followallinstructions
listedbelow,mayresultinelectricshock,fireand/or
seriouspersonalinjury.
SAVE THESE mNSTRUCTmONS
WORK
AREA
[] Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
[] Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
[] Keep bystanders, children, and visitors sway while
operating s power tool. Distractions can cause you to
lose control.
ELECTRmCAL
SAFETY
[] A battery operated tool with integral batteries or s
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a
risk of fire when used with another battery.
[] Use battery operated tool only with specifically
designated battery pack. Use of any other batteries
may create a risk of fire.
[] Use battery
MODEL
315.114840
only with charger
listed.
BATTERY PACK
item no. 9 11375
CHARGER
item no. -9 11401
1323903 or 1323517
1425301
[] Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
PERSONAL
SAFETY
[] Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious
personal injury.
[] Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
[] Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery pack.
Carrying tools with your finger on the switch or inserting the battery pack into a too! with the switch on
invites accidents.
[] Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
[] Do not overreach. Keep proper footing and balance
st all times. Proper footing and balance enable better
control of the too! in unexpected situations.
[] Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
[] Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
[] Do not use on s ladder or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
TOOL USE AND CARE
[] Use clamps or other practical way to secure and
support the workpiece to s stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
[] Do not force tool. Use the correct tool for your
application. The correct too! will do the job better and
safer at the rate for which it is designed.
[] Do not use tool if switch does not turn it on or off. A
tool that cannot be controlled with the switch is
dangerous and must be repaired.
[] Disconnect battery pack from tool or place the
switch in the locked or off position before making
any adjustments, changing accessories, or storing
the tool. Such preventive safety measures reduce the
risk of starting the tool accidentally.
[] Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
[] When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
[] Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp
cutting edges are less likely to bind and are easier to
control.
[] Check for misslignment
or binding of moving parts,
breakage of parts, and any other condition that
may affect the tool's operation, if damaged, have
the tool serviced before using. Many accidents are
caused by poorly maintained tools.
[] Use only accessories that are recommended
by the
manufacturer for your model. Accessories that may
be suitable for one too! may create a risk of injury when
used on another too!.
[] Keep the tool and its handle dry, clean and free
from oil and grease. Always use a clean cloth when
cleaning. Never use brake fluids, gasoline, petroleumbased products, or any strong solvents to clean your
too!. Following this rule wil! reduce the risk of loss of
control and deterioration of the enclosure plastic.
SERVmCE
[] Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personne! may result in a risk of injury.
[] Homdtoom by insumated gripping surfaces when
performing an operation where the cutting toom may
contact hidden wiring. Contact with a "live" wire will
also make exposed metal parts of the tool "live" and
shock the operator.
[] Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
tool. Following this rute will reduce the risk of electric
shock, fire, or serious injury.
[] Always wear safety glasses with side shields.
Everyday glasses have only impact resistant lenses.
They are NOT safety glasses. Following this rule wil!
reduce the risk of eye injury.
[] Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not using your battery tool or when changing
accessories.
Following this rule wil! reduce the risk of
electric shock, fire, or serious personal injury.
[] Do not place battery tools or their batteries near
fire or heat. This will reduce the risk of explosion and
possibly injury.
[] When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance hstructions may create a
risk of shock or injury.
[] Never use a battery that has been dropped or
received a sharp blow. A damaged battery is subject
to explosion. Properly dispose of a dropped or dam=
aged battery immediately.
[] Batteries vent hydrogen gas and can explode in
the presence of a source of ignition, such as a pilot
light. To reduce the risk of serious persona! injury,
never use any cordless product in the presence of
open flame. An exploded battery can propel debris and
chemicals. If exposed, flush with water immediately.
[] Do not charge battery tool in a damp or wet
location. Fol!owing this rule will reduce the risk of
electric shock.
[] For best results, your battery tool should be
charged in a location where the temperature
is
more than 50°F but less than 100°F. Do not store
outside or in vehicles.
[] Under extreme usage or temperature conditions, battery leakage may occur, if liquid comes
in contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar, if liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
_
WARNING!
READ AND UNDERSTAND ALL
iNSTRUCTiONS° Failure to follow all instructions
listed below, may result in electric shock, fire
and/or serious personal injury.
[] Before using battery charger, read al! instructions
and cautionary markings in this manual, on battery
charger, battery, and product using battery to prevent
misuse of the products and possible injury or damage.
CAUTION: To reduce the risk of electric shock or
damage to the charger and battery, charge only
nickel=cadmium rechargeable batteries as specifi=
cally designated on your charger. Other types of
batteries may burst, causing personal injury or
damage.
[] Do not use charger outdoors or expose to wet or
damp conditions. Water entering charger will increase
the risk of electric shock.
[] Use of an attachment not recommended
or sold
by the battery charger manufacturer
may result in
a risk of fire, electric shock, or injury to persons.
Following this rule will reduce the risk of electdc shock,
fire, or serious personal injury.
[] Do not abuse cord or charger. Never use the cord to
carry the charger. Do not pull the charger cord rather
than the plug when disconnecting from receptacle.
Damage to the cord or charger could occur and create
an electric shock hazard. Replace damaged cords ira=
mediately.
[] Make sure cord is located so that it will not be
stepped on, tripped over, come in contact with
sharp edges or moving parts or otherwise subjected to damage or stress. This wil! reduce the risk of
accidental fails, which could cause injury, and damage
to the cord, which could result in electric shock.
[] Keep cord and charger from heat to prevent
damage to housing or internal parts.
[] Do not let gasoline, oils, petroleum=based
products,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy plastic.
[] An extension cord should not be used unless
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord Length (Feet)
25'
50'
100'
Cord Size (AWG)
16
16
16
NOTE: AWG = American Wire Gauge
[] Do not operate charger with a damaged cord or
plug, which could cause shorting and electric shock. If
damaged, have the charger replaced by an authorized
serviceman.
[] Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way. Take it to an authorized serviceman for electrical
check to determine if the charger is in good working
order.
[] Do not disassemble charger. Take it to an authorized
serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or
fire.
[] Unplug charger from outlet before attempting any
maintenance or cleaning to reduce the risk of
electric shock.
[] Disconnect charger from the power supply when
not in use. This wi[! reduce the risk of electric shock
or damage to the charger if metal items should fail into
the opening. It also wi[! help prevent damage to the
charger during a power surge.
[] Risk of electric shock. Do not touch uninsulated
portion of output connector or uninsulated battery
terminal.
[] Save these instructions.
Refer to them frequently and
use them to instruct others who may use this too!. If
you loan someone this tool, loan them these instructions also to prevent misuse of the product and
possible injury.
absolutely necessary. Use of improper extension cord
could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
A
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
lead from lead-based paints,
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
5
Someof the followingsymbolsmaybe usedon this too!. Pleasestudythemand learntheirmeaning.Proper
interpretation
of thesesymbolswillallowyouto operatethe too!betterandsafer.
SYMBOL
NAME
DESIGNATION/EXPLANATmON
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency(cyclespersecond)
W
Watt
Power
min
Minutes
Time
Q,
AlternatingCurrent
Typeofcurrent
H_
DirectCurrent
Typeor a characteristic
of current
no
NoLoadSpeed
Rotationalspeed,at no load
ClassII Construction
Doubleqnsulated
construction
Per Minute
Revolutions,
.../rain
Wet Conditions
Alert
Read The Operator's
®
strokes, surface speed, orbits etc., per minute
Do not expose to rain or use in damp locations.
Manual
To reduce the risk of injury, user must read and understand
operator's manual before using this product.
Eye Protection
Always wear safety goggles or safety glasses with side
shields and a ful! face shield when operating this product.
Safety Alert
Precautions that involve your safety.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
serious
Failure topersonal
keep your
injury.
hands away from the blade will result in
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
Hot Surface
To reduce the risk of injury or damage, avoid contact with
any hot surface.
6
Thefollowingsignalwordsandmeanings
areintendedto explainthe levelsof riskassociatedwiththisproduct.
SYMBOL
SIGNAL
MEANING
DANGER:
hdicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING:
hdicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTmON:
hdicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
CAUTmON:
(Without Safety Alert Symbol) hdicates
property damage.
a situation
that may result in
L
SERVICE
Servicing requires extreme care and knowledge and
should be performed only by a qualified service technician. For service we suggest you return the product to
your nearest AUTHORIZED SERWOE CENTER for
repair. When servicing, use only identical replacement
parts.
WARNING: To avoid serious personal injury,
do not attempt to use this product until you read
thoroughly and understand completely the
operator's manual. Save this operator's manual
and review frequently for continuing safe operation and instructing others who may use this
product.
WARNING:
The operation of any power too! can result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power tool operation, always wear safety
goggles or safety glasses with side shields and a full face shield when needed. We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side
shields. Always use eye protection which is marked to comply with ANSI Z87.!.
SAVE THESE INSTRUCTIONS
PRODUCT
SPECIFICATIONS
Chuck ............................................................................................................................................................................
Clutch ....................................................................................................................................................................
1/2 in.
24 Position
Motor ...................................................................................................................................................................
19.2 Volt DC
Switch ..............................................................................................................................................................
Variable Speed
Gear Box ...................................................................................................................................................................
No Load Speed .........................................................................................................................................
Hammer Speed ...................................................................................................................................
Charger hput .......................................................................................................................................
2 Speed
0-400/0-1400/min.
0-5200/0-18200
BPM*
120 V, 60 Hz, AC only
Charge Rate .................................................................................................................................................................
Torque ......................................................................................................................................................
*Blows Per Minute
TWO-SPEED
GEARTRAIN (HI-LO)
TORQUE
ADJUSTMENTRiNG
KEYLESS
OHUOK
\
! Hour
Maximum 410 in.lb.
DEPTH GAUGE HOD
LEVEL
4
)
LEVEL
RVIEW
DIREOTIONOF
ROTATIONSELECTOR
(FORWARD/REVERSE)
BITSTORAGE
80REWDRIVER
BITS
BATTERY PACK
AUXILIARY
HANDLE ASSEMBLY
/
WRIST STRAP
Do not use any DC to AC power
CAUTUON
inverters. Charger wi|l be Damaged!
i
CHARGER
Fig. 1
KNOW YOUR
HAMMER
DR(LL
See Figure 1.
DEPTH
GAUGE
ROD
Before attempting to use this product, familiarize yourself
with a(I operat(ng Features and Safety Rules,
A depth gauge rod is installed on the auxiliary handle
assembly to assist you in controlling the depth of drilled
holes,
KEYLESS
AUXIMARY
CHUCK
Your drill-driver has a keyless chuck that allows you to
hand tighten or release dri(( bit in the chuck jaws,
SW(TCH
Your hammer dri(I has a conveniently located trigger
switch,
TWO-SPEED
GEAR TRAIN
Your drill-driver has a two speed gear train designed for
drilling or driving at HI or LO speeds, A slide switch is
located on top of your dri(( to select either HI or LO speed,
This hammer drill allows you to reverse the bit rotation, You
can control the direction with the direction of rotation selector located above the switch,
SW(TCH
LOCK
The switch trigger can be locked in the OFF position, This
feature helps reduce the possibility of accidenta( starting
when not in use,
ADJUSTABLE
TORQUE
CLUTCH
The hammer drill is equipped with an adjustable torque
clutch for driving different types of screws into different
materials,
HANDLE
ASSEMBLY
An auxiliary handle is installed on the hammer drill, For
ease of operation, you may use the handle with either the
left hand or the right hand,
LEVEL DR(LMNG
Two levels are recessed in the motor housing of the hammet dri(!, One is located on top, while the other is located
on the end, They can be used to keep dri(( bits level during
both horizontal and vertical drilling operations,
BiT STORAGE
When not in use, you can place the bits provided with your
hammer dri(( in the storage area located on the top of the
drill,
ERGONOM(C
DESIGN
The design of the hammer drill provides for easy handling,
It is designed for comfort and ease of grasp when operating in different positions and at different angles,
CHARGER
Your charger has a "key hole" feature for convenient, space
saving storage, Screws should be installed so that center
distances are 4-1/2 inches apart,
UNPACKING
WARNING:
Hfany parts are missing do not operate
this tool until the missing parts are replaced. Failure
to do so could result in possible serious personal
injury.
This product has been shipped completely assembled.
[] Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing fist
are included.
WARNING:
Do not attempt to modify this tool
or create accessories not recommended for use
[] hspect the tool carefully to make sure no breakage or
damage occurred during shipping.
with this toot. Any such alteration or modification is
misuse and could result in a hazardous condition
[] Do not discard the packing material untiI you have
carefully inspected and satisfactorily operated the tool.
leading to possible serious personal injury.
[] Hfany parts are damaged or missing, please call
1-800-932-3188 for assistance.
WARNING: To prevent accidental starting that
could cause serious personal injury, always remove
the battery pack from the too! when assembling
parts.
PACKmNG MST
Hammer Drill with Auxiliary Handle Assembly
Battery Pack (2)
Bits (2)
Depth Gauge Rod
Charger
Carrying Case
Operator's Manual
_
CAUTION: To prevent damage to the battery pack, remove the battery pack from the charger immediately if
no LED comes on. Return the battery pack and charger
to your nearest service center for checking or replacing. Also, if you are removing the battery pack from the
charger and no LEDs are on, return both the battery
pack and the charger to your nearest service center.
Do not insert another battery pack into the charger. A
damaged charger may damage a battery pack.
WARNmNG: Do not al!ow familiarity with tools to
make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious
injury.
_
WARNING:
Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
LED FUNCTmONS
APPUCATmONS
OF CHARGER
[] Hammer drilling in concrete, brick, or other masonry.
LED WmLL BE ON TO mNDmCATE STATUS OF
CHARGER AND BATTERY PACK:
[] Drilling in wood.
[] Red LED on = Fast charging mode.
[] Drilling in ceramics, plastics, fiberglass, and laminates.
[] Green LED on = Fully charged and in trickle charge
mode.
You may use this tool for the following purposes:
[] Drilling in both soft and hard metals.
[] Green LED on = When battery pack is inserted into
charger, indicates hot battery pack or that battery pack
is out of or below normal temperature range.
[] Driving screws with screwdriver bits, using driving accessories.
[] Mixing paint.
[] Yellow and Green LEDs on = Deeply discharged or
defective battery pack.
[] No LED on = Defective charger or battery pack.
10
CHARGmNG THE BATTERY
PACK
[] If both yellow and green LEDs come on, this indicates
a deeply discharged or defective battery pack. Allow
the battery pack to remain in the charger for 15 to 30
minutes. When the battery pack reaches normal
voltage range, the red LED should come on. If the red
LED does not come on after 30 minutes, this may
indicate a defective battery pack and should be
replaced.
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it until the green LED on the front of the
charger comes on.
NOTE: Batteries will not reach full charge the first time
they are charged. Allow several cycles (operation followed
by recharging) for them to become fully charged.
CHARGING
A COOL
BATTERY
[] After normal usage, a minimum of 1 hour of charging
time is required to fully recharge battery pack.
PACK
[] The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
See Figure 2.
Hfbattery pack is below normal temperature range, the
green LED on charger will come on. Allow battery pack to
reach normal temperature, then the red LED will come on.
[] Do not place the charger and battery pack in an area
of extreme heat or cold. They wil! work best at normal
room temperature.
NOTE: Hfthe charger does not charge the battery pack
under normal circumstances, return both the battery pack
and charger to your nearest Sears Repair Center for
electrical check.
NOTE: The charger and battery pack should be placed
in a location where the temperature is more than 50°F
but less than 100°F.
[] Charge the battery pack only with the charger provided.
[] When batteries become fully charged, unplug the
charger from power supply and remove the battery
[] Make sure the power supply is normal household
voltage, 120 volts, 60 Nz, AC only.
pack.
[] Connect the charger to the power supply.
CHARGING
[] Place the battery pack in the charger aligning raised rib
on the battery pack with the groove in the charger.
A HOT BATTERY
PACK
When using the tool continuously, the batteries in the
battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before
attempting to recharge. When the battery pack becomes
discharged and is hot, this wil! cause the green LED to
come on instead of the red LED. After 30 minutes, reinsert
the battery pack in the charger. If the green LED continues
to remain on, return battery pack to your nearest Sears
Repair Center for checking or replacing.
[] Press down on the battery pack to be sure contacts on
the battery pack engage properly with contacts in the
charger.
[] Normally the red LED on charger will come on. This
indicates the charger is in fast charging mode.
[] Red LED should remain on for approximately 1 hour
then the green LED will come on. Green LED on
indicates battery pack is fully charged and charger is
in maintenance charge mode.
NOTE: This situation only occurs when continuous use of
the tool causes the batteries to become hot. It does not
occur under normal circumstances. Refer to "CHARGING A COOL BATTERY PACK" for normal recharging
of batteries. If the charger does not charge your battery
pack under normal circumstances, return both the battery
pack and charger to your nearest Sears Repair Center for
electrical check.
NOTE: The green LED will remain on until the battery
pack is removed from the charger or charger is
disconnected from the power supply.
BATTERY PACK
SHOWN INCHARGER
Fig. 2
11
SWITCH
TO mNSTALL BATTERY
See Figure 3.
See Figures 5 - 6.
To turn your ddll ON, depress the switch trigger, To turn it
OFF, release the switch trigger,
[] Lock switch trigger on your drill by placing the direction
of rotation selector in center position.
[] Place battery pack in your drill. Align raised rib on
battery pack with groove inside drill.
[] Make sure the latches on each side of your battery
pack snap in place and battery pack is secured in dril!
before beginning operation.
PACK
CAUTION: When placing battery pack in your driI!,
be sure raised rib on battery pack aligns with groove
inside drill and latches snap into place properly.
Improper assembly of battery pack can cause
damage to internal components.
VARIABLE
SPEED
SWITCHTRIGGER
VARIABLE
FORWARD/ REVERSE
SELECTOR
Fig. 3
SPEED
This tool has a variable speed switch that delivers higher
speed and torque with increased trigger pressure. Speed
is controlled by the amount of switch trigger depression.
NOTE: You might hear a whistling or ringing noise from the
switch during use. Do not be concerned, this is a normal
part of the switch function.
TWO-SPEED
See Figure 4.
GEAR TRAIN
LATCHES
Your drill has a two-speed gear train designed for dritling or
driving at LO (1) or HI (2) speeds. A slide switch is located
on top of your drill to select either LO (1) or HI (2) speed.
When using drill in the LO (1) speed range, speed will
decrease and unit will have more power and torque. When
using dril! in the HI (2) speed range, speed will increase
and unit will have less power and torque. Use LO (1) speed
for high power and torque applications and HI (2) speed for
fast drilling or driving applications.
TWO SPEED
GEARTRAIN (HFL0)
DEPRESSLATCHESTO
RELEASEBATTERYPACK
TO REMOVE
L0
BATTERY
Fig. 5
PACK
See Figures 5 - 6.
SPEED
[] Lock switch trigger on your dril! by placing the direction
of rotation selector in center position.
SPEED
[] Locate latches on side of battery pack and depress to
release battery pack from your drill.
[] Remove battery pack from your dril!.
Fig. 4
12
SWITCHLOCK
_
WARN(NG:
Do not hold chuck body with one hand
and use power of the drift to tighten chuck jaws on
drift bit. Chuck body could slip in your hand or your
hand could slip and come in contact with rotating drift
bit. This could cause an accident resulting in serious
persona! injury.
Bee ,Figure 6.
The switch trigger can be locked in the OFF position, This
feature can be used to prevent the possibility of accidental
starting when not in use. To lock switch trigger, place the
direction of rotation selector (Forward/Reverse Selector) in
center position. NOTE: When selector is in center position,
switch trigger is locked.
SELECTORWITH
CENTERLOCKPOSITION
DRILL BIT
UNLOCK
CHUCK
(RELEASE
COLLAR
REVERSE
CHUCKJAWS
FORWARD
SWITCH
TRIGGER
Fig, 7
Fig, 6
INSTALLING
See Figures 6- 8.
WARNING:
Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
,_
REVERSIBLE
See Figure 6.
This tool has the feature of being reversible. The direction
of rotation is controlled by a selector located above the
switch trigger. With the drill held in normal operating position, the direction of rotation selector should be positioned
to the left of the switch for drilling. The dri(fing direction is
reversed when the selector is to the right of the switch.
When the selector is in center position, the switch trigger is
locked.
WARNING:
adjustments
Remove battery pack when making
or changing bits.
m
Lock the switch trigger by placing the direction of
rotation selector in center position.
m
Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use.
Also, raise the front of your drill slightly to keep the bit
from falling out of the chuck jaws.
m
Insert drill bit straight into chuck the full length of the
jaws.
m
Tighten the chuck jaws on drill bit.
m
To tighten the chuck jaws on drill bit; grasp and hold
the collar of the chuck with one hand, while rotating
the chuck body with your other hand.
CAUTION:
To prevent gear damage, always allow
chuck to come to a complete stop before changing
the direction of rotation.
NOTE: Rotate the chuck body in the direction of the
arrow marked LOCK to tighten chuck jaws.
To stop, release switch trigger and allow the chuck to come
to a complete stop.
KEYLESS
BITS
m
CHUCK
Do not use a wrench to tighten or loosen the chuck
jaws.
See Figure 7.
Your drill has a keyless chuck. As the name implies, you
can hand tighten or release drill bits in the chuck jaws.
Grasp and hold the collar of the chuck with one hand.
Rotate the chuck body with your other hand. The arrows
on the chuck indicate which direction to rotate the chuck
body in order to LOCK (tighten) or UNLOCK (release) the
drill bit.
13
_
TO DEOREASE
TORQUE
WARNING:Makesureto insertdrillbit straightinto
chuckjaws.Donotinsertdrillbit intochuckjaws
at ananglethentighten,asshownin Figure8.This
couldcausedrillbit to bethrownfromddll,resulting
inpossibleseriouspersonalinjuryor damagetothe
chuck.
TORQUE
ADJUSTINGRING
Fig. 9
USmNG THE HAMMER
MODE
See Figure 10.
See Figures 6 o 7.
The hammer mode should only be used for masonry, brick,
tile and concrete. For maximum performance, use carbide
tipped impact masonry bits. Follow these steps to use the
hammer mode.
[]
Lock the switch trigger by placing the direction of
rotation selector in center position.
[]
Rotate the torque adjustment ring until the arrow
points to the hammer mode.
[]
Loosen the chuck jaws from drill bit.
[]
[]
To loosen: grasp and hold the collar of the chuck with
one hand, while rotating chuck body with your other
hand.
Apply light pressure and medium speed for best resuits in brick.
[]
Apply additional pressure and high speed for hard
materials such as concrete.
NOTE: Rotate chuck body in the direction of the arrow marked UNLOCK to loosen chuck jaws.
[]
When dril!ing holes in tile, practice on a scrap piece to
determine the best speed and pressure.
Fig.8
REMOVINGBiTS
[]
Do not use a wrench to tighten or loosen the chuck
jaws.
[]
Remove dril! bit from chuck jaws.
ADJUSTABLE
TORQUE
CLUTCH
Your drill is equipped with an adjustable torque clutch for
driving different types of screws into different materials.
The proper setting depends on the type of material and the
size of screw you are using.
TO DEOREASETORQUE
TO ADJUST TORQUE
See Figure 9.
[]
Hdentify the twenty four torque indicator settings located
on the front of your drill.
[]
Rotate adjusting ring to the desired setting.
1- 4
For driving small screws.
5 - 8
For driving screws into soft material.
9 - 12
13 - 16
For driving screws into soft and hard
materials.
For driving screws in hard wood.
17 - 20
For driving large screws.
21 -4,_!
For heavy drilling.
TO INOREASETORQUE
TORQUE
ADJUSTING RING
Fig. 10
For hammer drilling.
14
BiT STORAGE
DRILLING
See Figure 11.
See Figure 13.
LEVEL
When not in use, bits provided with your drill can be
placed in the storage area iocated on the bottom of your
drill.
SCREWDRIVERBiT
BIT STORAGEAREA
_
Fig. 11
WARNING: Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
Fig. 13
LEVEL
See F_Ture 12.
When drilling hard smooth surfaces use a center punch
to mark desired hob location. This will prevent the dril! bit
from slipping off center as the hob is started. However,
the low speed feature allows starting holes without center
punching if desired. To accomplish this, simply operate
your drill at a !ow speed until the hole is started.
The material to be drilled should be secured in a vise or
A convenient feature provided with your drill is a leve!, it
is recessed in the motor housing on top and end of your
drill, it can be used to keep dril! bit level during drilling
operations.
with clamps to keep it from turning as the dril! bit rotates.
Hold toot firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
Move the dril! bit into the workpiece applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
_
WARNING:
Be prepared for binding at bit
breakthrough. When these situations occur, drill has
a tendency to grab and kick opposite to the direction
of rotation and could cause loss of control when
breaking through material. If not prepared, this !oss of
control can result in possible serious injury.
When dritling metals, use a light oil on the drill bit to keep it
from overheating. The oi! will prolong the life of the bit and
increase the drilling action.
If the bit jams in workpiece or if the dril! stalls, release
switch trigger immediately. Remove the bit from the
workpiece and determine the reason for jamming.
15
WARNING:Topreventacc(dental
startingthat
cou(dcauseseriouspersona(
(njury,aiwaysremove
the batterypackfromthetoo(whenmakingadjustments.
AOJUST(NG
ASSEMBLY
THE AUXIL(ARY
ADJUST(NG
See Figure 14.
Follow these steps to adjust the auxiliary handle assemb(y,
Loosen the auxiliary handle assembly by turning the
knob counterc)ockwise,
[]
Rotate the auxiliary handle assembly to the desired
(ocation,
[]
Tighten the auxiliary hand(e assembly secure(y by
turning the knob c(ockw(se,
TORQUE
ADJUSTMENTR)NG
AUX(L(ARY
HANDLE AS$EMBLY
ROD
Follow these steps to adjust the depth gauge rod,
HANDLE
[]
THE DEPTH GAUGE
See Figure 15.
[]
Lock the tr(gger switch by p(acing the rotation selector
(n the center position,
[]
Loosen the auxi)(ary handle assemb(y by turning the
knob counterclockw(se,
[]
Adjust the depth gauge rod so that the drill bit extends
beyond the end of the rod to the required drilling depth,
[]
Tighten the aux((iary handle assemb(y by turning the
knob c(ockw(se,
TODECREASE
DR(LL(NGDEPTH
GROOVE
TO (NCREASEDR(LING
DEPTH
DEPTH
GAUGEROD
DR(LLING
DEPTH
"_
AUX(L(ARY
HANDLEA$SEMBLY
TO LOOSEN
DRILLB(T
TOTIGHTEN
F(g. 15
TO
TIGHTEN
360° ROTATION
Fig. 14
16
CHUCK REMOVAL
TO RETIGHTEN
See Figures 16 ° 18.
The chuck may become loose on spindle and develop a
wobble, Periodically check chuck screw for tightness,
The chuck may be removed in order to use some accessories,
A LOOSE
CHUCK
To remove:
[] Lock the switch trigger by placing the direction of rotation selector in center position.
[] hsert a 5/16 in. or larger hex key into the chuck of your
ddll and tighten the chuck jaws securely.
[] Tap the hex key sharply with a mallet in a clockwise direction. This wil! loosen the screw in the chuck for easy
removal.
Fig. 18
To tighten:
[] Lock the switch trigger by placing the direction of rotation selector in center position.
[] Open the chuck jaws.
[] hsert hex key into chuck and tighten chuck jaws securely. Tap hex key sharply with a mallet in a clockwise
direction. This wil! tighten chuck on the spindle.
Fig. 16
[] Open chuck jaws and remove hex key. Remove the
chuck screw by turning it in a clockwise direction.
[] Open the chuck jaws and remove hex key.
[] Tighten the chuck screw.
NOTE: The screw has Idt hand threads.
NOTE: The chuck screw has left hand threads.
[] hsert hex key in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a counterclockwise
direction. This will loosen chuck on the spindle. Htcan
now be unscrewed by hand.
17
_
WARNING:Whenservicing,useonlyidentical
Craftsman
replacement
parts.Useofanyotherpart
maycreatea hazardor causeproductdamage.
_
WARNING:Alwayswearsafetygogglesor safety
glasseswithsideshieldswhenusingcompressed
air
to cleantools.Hftheoperationis dusty,alsoweara
dustmask.
_
_
WARMNG:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc. come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which
may result in serious personal injury.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. Al! other parts
should be replaced at a Sears Service Center.
WARNING:Toavoidseriouspersonalinjury,always
removethe batterypackfromthetoolwhencleaning
or performing
anymaintenance.
GENERAL
MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, ei!, grease, etc.
BATTERY PACK REMOVAL AND
PREPARATION
FOR RECYCUNG
The battery pack for this tool is equipped with nickel-cadmium rechargeable batteries. Length of service from each
charging wil! depend on the type of work you are doing.
To preserve natural resources, please
recycle or dispose of batteries
properly.
The batteries in this tool have been designed to provide
maximum trouble-free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry, could
result in a serious burn.
This product contains nickeFcadmium
batteries. Local, state or federal
laws may prohibit disposal of nickelcadmium batteries in ordinary trash.
Consult your local waste authority for information
regarding available recycling and/or disposal options.
To obtain the longest possible battery life, we suggest the
following:
WARMNG:
Upon removal, cover the battery pack's
terminals with heavy-duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nicke!-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
[] Remove the battery pack from the charger once it is
fully charged and ready for use.
For battery pack storage longer than 30 days:
[] Store the battery pack where the temperatures
low 80°F.
[] Store battery packs in a "discharged"
is be-
condition.
18
_-
CRAFTSMAN
SEE BACK
19.2V CORDLESS
HAMMER
PAGE FOR PARTS ORDERING
E)R_LL - 315.114840
_NSTRUCT_ONS
6
Key
No.
Pa_
Number
1
6613402
2
300188024
3
690033052
Auxiliary Handle Assembly ..............................................................
Chuck ...............................................................................................
1
1
4
630412003
Depth Gauge Rod ............................................................................
1
5
940203007
Logo Plate ........................................................................................
1
6
1323903
Battery Pack (Item no. _911375) ......................................................
1
7
1425301
Battery Charger (Item no. 9=11401) ..................................................
1
983000=487
Operator's
Description
Chuck Screw ...................................................................................
Manual
* Standard Hardware item - May Be Purchased Locally
** Available From Div° 98 - Source 980.0
*** Complete
assortment
available
at your Nearest
19
Sears Retail Store
Qty.
1
Your Home
For repair-in
your home-of
all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
..................
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
..................
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
..................
1-8 00-4-MY-H 0 ME® (1-800-469-4663)
oa,,
an t, o, o,oht sod
Oaoada
www.sears.com
..........
www.sears.ca
Our
Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime,
day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced
1-800-827-6655
Pard pedir servicio
(U.S.A.)
1-800-361-6665
de reparacien
Au Canada
a domicilio, y para ordenar piezas.
1-8 8 8-S U- HO G AR sM
by Sears:
(Canada)
pour service en frangais:
1 -800- LE- FO YER Mc
(1-800-533-6937)
(1-888-784-6427)
www.sears.ca
...............
..............
SEARS
® Registered
Trademark
/ TMTrademark
/
SM
Service
Mark of Sears,
Roebuck
® Marca Registrada
/ TM Marca de F_brica / SM Marca de Servicio
de Sears,
MC
Marque
de commerce
/ MD Marque
d6pos6e
de Sears,
Roebuck
and Co.
and Co.
Roebuck
and
Co.
® Sears,
Roebuck
and Co.