Christie DWX555-GS User manual

GS Series
DWX555-GS/DHD555-GS/DWU555-GS
USER MANUAL
020-000724-01
The CD included with this printed manual contains an electronic copy in English. Please read all instructions before
using or servicing this product.
Le DC fourni avec ce manuel imprimé contient une copie électronique en français. S'il vous plaît lire toutes les
instructions avant d'utiliser ou de réparer ce produit.
Die mit dieser gedruckten Anleitung gelieferte CD enthält eine elektronische Kopie in Deutsch. Bitte lesen Sie alle
Anweisungen, bevor Sie dieses Produkt verwenden oder warten.
Il CD fornito con il manuale stampato contiene una copia elettronica in lingua italiano. Si prega di leggere tutte le
istruzioni prima di utilizzare o riparare questo prodotto.
El DC incluido con este manual impreso contiene una copia electrónica en español. Por favor, lea todas las
instrucciones antes de usar o dar servicio a este producto.
NOTICES
COPYRIGHT AND TRADEMARKS
Copyright ©2014 Christie Digital Systems USA, Inc. All rights reserved.
All brand names and product names are trademarks, registered trademarks or trade names of their
respective holders.
REGULATORY
The product has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the product is operated in a commercial environment. The
product generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of the product in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at the user's own expense.
WARNING! Changes or modifications not expressly approved by Christie could void the user's
authority to operate the product.
FOR COMMERCIAL USE ONLY - POUR USAGE COMMERCIAL UNIQUEMENT
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING 2 CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
CET APPAREIL NUMÉRIQUE DE CLASSE A EST CONFORME AUX NORMES DÉFINIES DANS
LES RÉGLEMENTATIONS CANADIENNES SUR LES APPAREILS CAUSANT DES
INTERFÉRENCES RADIO (CANADIAN INTERFERENCE-CAUSING EQUIPMENT
REGULATIONS, ICES-003, CLASS A).
!
!
!
!
!
-!
!
! !
!
!
!
!
!
!
!
!
/
!
GENERAL
Every effort has been made to ensure accuracy, however in some cases changes in the products or
availability could occur which may not be reflected in this document. Christie reserves the right to
make changes to specifications at any time without notice. Performance specifications are typical,
but may vary depending on conditions beyond Christie's control such as maintenance of the
product in proper working conditions. Performance specifications are based on information
available at the time of printing. Christie makes no warranty of any kind with regard to this material,
including, but not limited to, implied warranties of fitness for a particular purpose. Christie will not be
liable for errors contained herein or for incidental or consequential damages in connection with the
performance or use of this material.
The product is designed and manufactured with high-quality materials and components that can be
recycled and reused. This symbol
means that electrical and electronic equipment, at their end-
of-life, should be disposed of separately from regular waste. Please dispose of the product
appropriately and according to local regulations. In the European Union, there are separate
collection systems for used electrical and electronic products. Please help us to conserve the
environment we live in!
Canadian manufacturing facility is ISO 9001 and 14001 certified.
GENERAL WARRANTY STATEMENTS
For complete information about Christie's limited warranty, please contact your Christie dealer. In
addition to the other limitations that may be specified in Christie's limited warranty, the warranty
does not cover:
a. Damage occurring during shipment, in either direction.
b. Problems caused by combination of the product with non-Christie equipment, such as distribution systems, cameras, video tape recorders, etc., or use of the product with any non-Christie
interface device.
c. Damage caused by misuse, improper power source, accident, fire, flood, lightening, earthquake or other natural disaster.
d. Damage caused by improper installation/alignment, or by product modification, if by other than
a Christie authorized repair service provider.
e. For LCD projectors, the warranty period specified applies only where the LCD projector is in
"normal use." "Normal use" means the LCD projector is not used more than 8 hours a day, 5
days a week. For any LCD projector where "normal use" is exceeded, warranty coverage under
this warranty terminates after 6000 hours of operation.
f. Failure due to normal wear and tear.
PREVENTATIVE MAINTENANCE
Preventative maintenance is an important part of the continued and proper operation of your
product. Please see the Maintenance section for specific maintenance items as they relate to your
product. Failure to perform maintenance as required, and in accordance with the maintenance
schedule specified by Christie, will void the warranty.
Table of Contents
1. SAFETY
2. INTRODUCTION
2.1
2.2
2.3
2.4
2.5
Projector Components .................................................................................................. 2-1
Built-in Keypad .............................................................................................................. 2-4
Input/Output (I/O) Panel ................................................................................................ 2-5
Remote Control ............................................................................................................. 2-6
LED Status Indicators ................................................................................................... 2-8
3. INSTALLATION
3.1
3.2
3.3
3.4
3.5
Connect to Computer .................................................................................................... 3-1
Connect to Video Equipment ........................................................................................ 3-2
Turn the Projector On.................................................................................................... 3-3
Turn the Projector Off.................................................................................................... 3-3
Adjust the Projector Position ......................................................................................... 3-4
Table Top Mode3-5
Portrait Mode3-5
3-5
Inverted Mode3-5
Non-Supported Modes3-6
3.6 Calculate Lens Offset.................................................................................................... 3-7
3.7 Removing and Installing the Lens ............................................................................... 3-13
3.8 Cable Cover Installation .............................................................................................. 3-14
3.9 Portrait Cover Installation............................................................................................ 3-15
3.10 Ceiling Mount Installation ............................................................................................ 3-16
4. OPERATION
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
Size and Position Menu ................................................................................................ 4-2
Image Settings Menu .................................................................................................... 4-7
Configuration Menu..................................................................................................... 4-10
Light Source ................................................................................................................4-15
Status Menu ................................................................................................................ 4-16
Input Switching & PIP Menu........................................................................................ 4-19
Language Menu .......................................................................................................... 4-21
Test Pattern Menu....................................................................................................... 4-21
Web User Interface ..................................................................................................... 4-22
4.9.1 Logging On..................................................................................................... 4-22
4.9.2 Main Tabbed Page - General ......................................................................... 4-22
4.9.3 Main Tabbed Page - Status............................................................................ 4-23
4.9.4 Main Tabbed Page - Lens .............................................................................. 4-24
4.9.5 Network .......................................................................................................... 4-25
4.9.6 Tools............................................................................................................... 4-28
4.9.7 Administrator Page......................................................................................... 4-28
4.9.8 About Page..................................................................................................... 4-29
4.10 Christie Presenter ....................................................................................................... 4-30
4.10.1 Connect to the Projector................................................................................. 4-30
4.10.2 Install Christie Presenter software.................................................................. 4-31
4.10.3 Use Christie Presenter ................................................................................... 4-32
4.11 Card Reader Operation............................................................................................... 4-38
i
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Table of Contents
5. TROUBLESHOOTING
6. SPECIFICATIONS
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
Inputs ............................................................................................................................ 6-1
PIP/PBP Compatibility .................................................................................................. 6-6
Key Features ................................................................................................................ 6-7
List of Components....................................................................................................... 6-8
Optional Accessories .................................................................................................... 6-8
REGULATORY ............................................................................................................. 6-9
Federal Communications Commission (FCC) Warning.............................................. 6-10
OSD Tree.................................................................................................................... 6-11
Preset Mode tables..................................................................................................... 6-19
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
ii
Section 1: SAFETY
1.
SAFETY
Read through this document in its entirety and understand all warnings and
precautions before attempting to operate the projector.
WARNING
.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1-1
Do not look into the projector lens when the laser is on. The bright light
may result in permanent eye damage.
To reduce the risk of fire or electric shock, do not expose this projector to
rain or moisture.
Do not open or disassemble the projector as this may cause electric shock.
All installation and maintenance procedures must be performed by a
Christie accredited service technician.
Keep all combustible material away from the concentrated light beam of
the projector.
Position all cables where they cannot contact hot surfaces or be pulled or
tripped over.
Always power down the projector and disconnect all power sources before
servicing or cleaning.
Use a soft cloth moistened with a mild detergent to clean the display
housing.
Disconnect the power plug from the AC outlet if the product is not being
used for an extended period of time.
Operate the projector under the following conditions:
- Operating temperature range: 5°C to 35°C
- Storage temperature range: -10°C to 60°C
- Humidity range: 5% to 80 % RH (Max.), non condensing
- Operating altitude: 10,000 ft. maximum
Use only the AC power cord supplied. Do not attempt operation if the AC
supply and cord are not within the specified voltage and power range for
your region.
Remove the lens plug from the lens opening in the projector before
installing the lens. Retain the lens plug to protect the optical components
from dust and debris during transport.
Do not block the ventilation slots and openings on the projector.
Do not use abrasive cleaners, waxes or solvents to clean the projector.
Do not allow anything to rest on the power cord.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 1: SAFETY
Warning
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Important Laser Notice
MAX OUTPUT:8.0mW
WAVE LENGTH:440~455nm
Complies with 21 CFR 1040.10 and 1040.11 except
for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.
IEC 60825-1:2007
.
•
•
•
•
•
•
•
WARNING
This projector is a Class 2 laser device that conforms with IEC 608251:2007 and CFR 1040.10 and 1040.11
Class 2 laser product, Do Not Stare Into Beam
This projector has built-in Class 4 laser module. Disassembly or
modification is very dangerous and should never be attempted.
Any operation or adjustment not specifically instructed by the user's guide
creates the risk of hazardous laser radiation exposure.
Do not open or disassemble the projector as this may cause damage by the
exposure of laser radiation.
Do not stare into beam when the projector is on. The bright light may result
in permanent eye damage.
Without following the control, adjustment or operation procedure may
cause damage by the exposure of laser radiation.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
1-2
Section 2: INTRODUCTION
2.
INTRODUCTION
The product specified in this document is a high brightness, high-resolution
video/graphics 1-chip laser based projector. The projector is available in
WXGA, HD and WUXGA resolutions. The projector utilizes Digital Light
Processing (DLP®) technology from Texas Instruments. It is primarily designed
for fixed installation markets.
2.1
Projector Components
Front View
1
2
3
4
Ind.
2-1
Part Name
Description
1
Front IR Sensor
Receives signals from the IR remote. Keep the signal
path to the sensor unobstructed for uninterrupted
communication with the projector.
2
Projection Lens
Allows automated lens control and adjustment:
vertical and horizontal offsets, zoom and focus.
3
Lens Ring
Protects the lens motors and mechanism. Remove in
order to insert or remove the lens.
4
Adjustable Feet
Raise or lower the feet to level the projector.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 2: INTRODUCTION
Rear View
1
HDBaseT
REMOTE
IN
REMOTE
OUT
HDMI
VGA IN
VGA OUT
DISPLAY PORT
2
DVI
MINI USB
GREEN/Y
BLUE/PB
RED/PR
RS232
USB
ETHERNET
CVBS
S-VIDEO
3
4
5
K
Ind.
Part Name
Description
1
Rear IR Sensor
Receives signals from the IR remote. Keep the signal
path unobstructed for uninterrupted communication
with the projector.
2
Input/Output (I/O) Panel
Connects the projector to external devices.
3
AC Input
Connect to the supplied power adapter.
4
Power Button
Switch the power button to turn on the power source.
5
Kensington Lock
Use to secure the projector to countertops, tables, etc.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
2-2
Section 2: INTRODUCTION
Left View
1
Right View
2
3
4
Ind.
2-3
Part Name
Description
1
Cooling Air Vents
(Intake)
Keep these vents unobstructed to prevent the
projector from overheating.
2
LED Status Indicators
Displays the status of the projector. They are (from left
to right): LIGHT, STATUS, and PIC MUTE.
3
Built-in Keypad
Controls the projector.
4
Cooling Air Vents
(Exhaust)
Keep these vents unobstructed to prevent the
projector from overheating.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 2: INTRODUCTION
2.2
Built-in Keypad
1
7
2
8
3
4
9
5
10
6
11
Ind.
Part Name
Description
1
Power
Turn the projector on or off
2
Menu
Display menus
3
Enter
Confirm a selection
4
Auto
Automatically optimize image
5
Lens
Adjust the lens vertical or horizontal offset setting
6
Focus
Adjust focus
7
Exit
Return to previous level or exit menus if at top level
8
Arrow Keys
•
•
9
Input
Select an input for the main or PIP/PBP image
10
Picture Mute
Display or blank the video image.
11
Zoom
Adjust zoom
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Adjust a setting UP or DOWN
Navigate within a menu
2-4
Section 2: INTRODUCTION
2.3
Input/Output (I/O) Panel
1
2
3
4
5
HDBaseT
REMOTE
IN
REMOTE
OUT
HDMI
VGA IN
6
VGA OUT
7
8
DISPLAY PORT
DVI
MINI USB
GREEN/Y
BLUE/PB
RED/PR
9
Ind.
2-5
Connector Name
RS232
10
USB
11
ETHERNET
12
13
Ind.
CVBS
S-VIDEO
14
15
Connector Name
1
HDBaseT
9
Component IN
2
Remote IN
10
RS232
3
Remote OUT
11
Mini USB
4
HDMI
12
USB Type A
5
VGA-IN
13
Ethernet
6
VGA OUT
14
CVBS
7
Display Port
15
S-Video
8
DVI
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 2: INTRODUCTION
2.4
Remote Control
1
2
16
3
17
4
5
18
19
20
6
21
7
22
8
9
23
10
24
25
11
26
12
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
27
13
14
28
15
29
2-6
Section 2: INTRODUCTION
Ind.
2-7
Part Name
Description
1
Picture Mute
Display or blank the video image.
2
Power on
Turn projector ON.
3
Gamma
Adjust mid-range levels.
4
Bright
Adjust amount of light in the image.
5
PIP/PBP
Turn PIP/PBP ON/OFF.
6
Size
Adjust the PIP/PBP size
7
Number Keys
Enter a number, such as a channel, value, etc.
8
Help
Display context-sensitive help.
9
Menu
Display menus.
10
Arrow Keys
•
•
11
Test
Display a test pattern.
12
Auto
Automatically optimize image.
13
OSD
Use to hide or show menus.
14
Keystone H
Adjust the horizontal keystone.
Adjust a setting UP or DOWN.
Navigate within a menu.
15
Keystone V
Adjust the vertical keystone.
16
Standby
Turn projector OFF.
17
Contrast
Adjust difference between dark and light.
18
Hot-key
Select your preset keys quickly.
19
Swap
Swap the main and PIP/PBP images.
20
Layout
Adjust the PIP/PBP layout.
21
Focus
Adjust focus to improve image clarity as desired.
22
Zoom
Adjust zoom to achieve a desired image size.
23
Proj Key
Change the remote ID. Press Proj Key then a number
between 1 and 9 to assign an ID. Press PROJ then
number 0 to return to the universal remote ID.
24
Exit
Return to previous level or exit menus if at top level.
25
Enter
•
•
26
Input
Select an input for the main or PIP/PBP image.
27
Info
Display source image information.
28
Lens H
Horizontal Lens Shift - Adjust the position of the image
horizontally.
29
Lens V
Vertical Lens Shift - Adjust the position of the image
vertically.
Select a highlighted menu item.
Change or accept a value.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 2: INTRODUCTION
2.5
LED Status Indicators
The LED status indicators are located on the right side of the projector. Each
LED is defined below.
•
LIGHT LED
LED Status
•
Projector State
Red (flashing)
When projector has lost over 60% initial luminance
Orange (solid)
Laser diode time has expired
Green (solid)
Laser diode is on and operating correctly
Off
Laser diode is off
STATUS LED
LED Status
Off
Projector State
AC power is off (without AC plug in)
Off, but keypad LED
AC has been applied, projector is in standby mode
is on
Green (solid)
Projector is powered up and operating normally
Green (flashing)
Projector communications
Orange (solid)
Non-portrait mode used
NOTE: Please refer to section 3.5.
Orange (flashing)
Projector is in cool down mode or startup mode
Green (flashing) /
Red (flashing)
Projector is in flash (LAN) update state
Red (solid)
Over-temperature
Red (flashing)
Fan failure
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
2-8
Section 2: INTRODUCTION
•
PICTURE MUTE LED
LED Status
2-9
Projector State
Green (solid)
Light is on - image is displayed
Orange (solid)
Light is on - image is blank
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 2: INTRODUCTION
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
2-10
Section 3: INSTALLATION
3.
INSTALLATION
3.1
Connect to Computer
Laptop
Desktop
9
1
2
HDBaseT
REMOTE
IN
3
REMOTE
OUT
HDMI
4
5
VGA IN
6
VGA OUT
7
DISPLAY PORT
8
DVI
MINI USB
GREEN/Y
Ind.
BLUE/PB
Connector Name
RED/PR
RS232
Ind.
USB
ETHERNET
CVBS
Connector Name
S-VIDEO
Ind.
Connector Name
1
RS232 Cable
4
USB Type B Mini
7
Cable
2
HDMI Cable
5
VGA out Cable
8
DVI Cable
3
VGA in Cable
6
USB Type A Cable
9
Power Cord
NOTE:



3-1
The diagram shows the cables/connectors that may be used to connect to various devices.
Due to the difference in applications for each country, the accessories required in some regions may be different from those
shown.
This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 3: INSTALLATION
3.2
Connect to Video Equipment
Component video output equipment
DVD player
Video cassette recorder
3
5
1
2
7
8
4
6
HDBaseT
REMOTE
IN
REMOTE
OUT
HDMI
VGA IN
VGA OUT
DISPLAY PORT
DVI
MINI USB
GREEN/Y
Ind.
Connector Name
BLUE/PB
RED/PR
Ind.
RS232
USB
Connector Name
1
Component
(YPbPr) Cable
4
VGA in Cable
2
HDMI Cable
5
3 RCA Component
Cable
3
VGA to RBG
SCART
6
15-pin to 3 RCA
Component/HDTV
Adapter
ETHERNET
CVBS
Ind.
S-VIDEO
Connector Name
7
CVBS Cable
8
S-Video Cable
NOTE:



The diagram shows the cables/connectors that may be used to connect to various devices.
Due to the difference in applications for each country, the accessories required in some regions may be different from those
shown.
This diagram is for illustrative purposes only, and does NOT indicate that these accessories are supplied with the projector.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
3-2
Section 3: INSTALLATION
3.3
Turn the Projector On
1. Ensure that the power cord and signal cable are securely connected. The
Power button on the built in keypad is illuminated. 1
2. Turn on the projector by pressing " " on the remote control or press " "
on the built-in keypad. The Status LED is Orange with a long blink. 12
3. Turn on the source. Select Input Key on the remote control to select an
input source (VGA, BNC, HDMI, Component, S-Video or Composite
Video). 13
4. The projector detects the source you selected and displays the image.
NOTE:

The first time the projector is used, the preferred language may be selected from the main menu after the startup screen is displayed.
2
1
12
2
1
Status LED
Power on
3
1
3.4
Power on
Input Key
Turn the Projector Off
1. Press " " on the built-in keypad or on the remote control to turn off the
projector. A warning message will appear on the displayed image.
2. Press " " again to confirm your selection. If you do not press " " again,
the warning message will disappear after 10 seconds.
3-3
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 3: INSTALLATION
3.5
Adjust the Projector Position
When you select a position for the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Follow these general guidelines:
• Position the projector on a flat surface at a right angle to the screen. The
projector (with the standard lens) must be at least 3 feet (0.9m) from the
projection screen.
• Position the projector to the desired distance from the screen. The distance
from the lens of the projector to the screen, the zoom setting, and the video
format determine the size of the projected image.
• For the fixed short lens, the image exits at a default angle. However, the
lens shift feature makes the image offset variable.
• Lens throw ratio:
- Lens 1.22~1.53 (WU/HD)
- Lens 0.95~1.22 (WU/HD)
- Lens 1.52~2.92 (WU/HD)
- Lens 1.28-1.61 (WX)
- Lens 1.0-1.28 (WX)
- Lens 1.6-3.07 (WX)
• 360 degree operation (alone the widest axis)
360°
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
3-4
Section 3: INSTALLATION
Table Top Mode
-
The projector is in table top mode when the viewing angle is from 0° to
<60° and from >300° to 360° as illustrated below.
300~360 deg
0 deg
0~60 deg
Portrait Mode
-
The projector is in portrait mode when the viewing angle is from 60° to
120° as illustrated below.
Portrait mode
60~120 deg
•
Portrait mode
60~120 deg
WARNING
In portrait orientation, the Portrait Side Cover must be installed on the side
of the projector which is now the lower side. Refer to section 3.9.
Inverted Mode
-
The projector is in Inverted/Ceiling Mount Mode when the viewing angle
is from >120° to <240° as illustrated below.
120~180 deg
3-5
180 deg
180~240 deg
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 3: INSTALLATION
Non-Supported Modes
-
The projector is in non-portrait mode when the viewing angle is 240° to
300° as illustrated below.
The "orange" status LED on projector lights on.
270~300 deg
240~270 deg
270 deg
WARNING
• The projector should not be operated in Non-Portrait Mode.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
3-6
Section 3: INSTALLATION
3.6
Calculate Lens Offset
•
•
The vertical image offset (shift) ranges for the projector are +/-100%
(WXGA/WUXGA) and +/-120% (HD). The horizontal image offset (shift)
range for the projector are +/-30% (WXGA/HD/WUXGA).
The method for calculating lens offset complies with Industry standards.
Example for Vertical lens offset:
- At 0% offset (or on axis), the center of the image is on the lens center,
so that half of the image appears above and half appears below the
lens center.
- At +100% offset, all (or 100%) of the image will appear above the lens
center.
- The % offset is calculated as the ratio of the number of pixels shifted up/
down to half the image size. Examples for WUXGA:
 Shifting up 600 pixels gives offset of 600/600 * 100% = 100%
 Shifting down 600 pixels gives offset of -600/600 * 100% = -100%
 Shifting up 720 pixels gives offset of 720/600 * 100% = 120%
 Shifting up 240 pixels gives offset of 240/600 * 100% = 40%
WUXGA Projectors:
Vertical Image Offset: 0% Offset (WUXGA)
No offset is applied - 0% offset.
Half of the image appears above lens center
and half of the image appears below lens
center.
600 pixels
above lens
center.
Lens center
600 pixels
above lens
center.
3-7
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 3: INSTALLATION
Vertical Image Offset: 100% Offset (WUXGA)
Image has been offset 600 pixels above
lens center, so the center of the image is
now 600 pixels above where the center of
the image was at 0% offset (or lens center).
The offset is +600/600 * 100% = +100%.
600 pixels of
shift above
lens center.
Lens center
Vertical Image Offset: -100% Offset (WUXGA)
Image has been offset 600 pixels below lens
center, so the image has an offset of -600/
600 * 100% = -100%
600 pixels
of shift
below lens
center.
Lens center
Total of
1200 pixels
(600+600)
of display
are below
lens center.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
3-8
Section 3: INSTALLATION
HD Projectors:
Vertical Image Offset: 0% Offset (HD)
No offset is applied - 0% offset.
Half of the image appears above lens center
and half of the image appears below lens
center.
540 pixels
above lens
center.
Lens center
540 pixels
above lens
center.
Vertical Image Offset: 120% Offset (HD)
Image has been offset 648 pixels above
lens center, so the center of the image is
now 648 pixels above where the center of
the image was at 0% offset (or lens center).
The offset is +648/540 * 100% = +120%.
648 pixels of
shift above
lens center.
Lens center
3-9
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 3: INSTALLATION
Vertical Image Offset: -120% Offset (HD)
Image has been offset 648 pixels below lens
center, so the image has an offset of -648/
540 * 100% = -120%
Lens center
648 pixels
of shift
below lens
center.
Total of
1296 pixels
(648+648)
of display
are below
lens center.
Horizontal Image Offset: +/-30% Offset
1920 pixels
+192 pixels
Lens center
-192 pixels
Image has been offset 192 pixels
left or right of lens center.
The image has an offset of +192/
960 * 100% = +20%, or -192/960 *
100% = -20%
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
3-10
Section 3: INSTALLATION
WXGA Projectors:
Vertical Image Offset: 0% Offset (WXGA)
No offset is applied - 0% offset.
Half of the image appears above lens center
and half of the image appears below lens
center.
400 pixels
above lens
center.
Lens center
400 pixels
above lens
center.
Vertical Image Offset: 100% Offset (WXGA)
Image has been offset 400 pixels above
lens center, so the center of the image is
now 400 pixels above where the center of
the image was at 0% offset (or lens center).
The offset is +400/400 * 100% = +100%.
400 pixels of shift
above lens center.
3-11
Lens center
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 3: INSTALLATION
Vertical Image Offset: -100% Offset (WXGA)
Image has been offset 400 pixels below lens
center, so the image has an offset of -400/
400 * 100% = -100%
Lens center
400 pixels of shift
below lens center.
Total of 800 pixels
(400+400) of
display are below
lens center.
Horizontal Image Offset: +/-30% Offset
1280 pixels
+128 pixels
Lens center
-128 pixels
Image has been offset 128 pixels
left or right of lens center. The
image has an offset of +128/640
* 100% = +20%, or +128/640 *
100% = -20%
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
3-12
Section 3: INSTALLATION
3.7
Removing and Installing the Lens
When handling the projector after lens installation, make sure the front lens
cap is placed on the lens to protect the lens surface from potential damage.
When carrying or moving the projector, do not handle by the lens. This may
damage the lens, the chassis or other mechanical parts within the projector.
Installation Steps:
1. Center the lens: Ensure that the lens is at or near its center position.
Attempting to remove the lens when at a large offset may cause damage to
the lens assembly. Center the lens while the projector is switched on by
pressing the lens horizontal or vertical button and then pressing Enter.
2. Turn Off the projector: Turn the projector OFF.
3. Wait for projector to cool down: Allow the projector to cool down into
standby mode before replacing the lens. Remove power cord after the
projector has cooled down and prior to replacing the lens.
4. Remove the lens: Remove the lens ring cover.
Rotate the lens counter-clockwise by a quarter to release the lock. Remove
the lens through the front of the projector.
5. Install the new lens: Fully insert the lens assembly straight into the lens
mount without turning. Rotate the lens cap clockwise to lock the lens in
place.
3-13
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 3: INSTALLATION
3.8
Cable Cover Installation
1. Rotate the cable cover and insert the two guide pins into the guide holes.
2. Press and hold both lower corners of the cable cover while inserting the
sheet clips into the projector casing.
Guide Pin
Guide Hole
Hold and Press Here
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
3-14
Section 3: INSTALLATION
3.9
Portrait Cover Installation
1. Attach the Portrait cover to the left side of the projector and secure with the
6 step screws.
Tighten the six screws
2. Mount the projector in an appropriate mounting kit, using the 4 mounting
points on the underside of the projector.
•
•
3-15
WARNING
Mount with the portrait cover side facing downwards.
The projector must not stand on a table top on the portrait cover
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 3: INSTALLATION
3.10
Ceiling Mount Installation
Mount the projector with an appropriate mounting kit, using the 4 mounting
points on the underside of the projector.
•
•
When not mounted properly, the projector may fall, causing hazards or
injury. The warranty on this projector does not cover any damage caused
by the use of any non-recommended ceiling mount kit or installation of the
ceiling mount kit in an improper location.
Refer to the installation instructions and safety guidelines provided in the
kit.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
3-16
Section 4: OPERATION
4.
OPERATION
The projector has multilingual On-Screen Display (OSD) menus that allow you
to make image adjustments and change a variety of settings.
•
•
•
•
•
4-1
Most of the projector controls are accessed from within the projector menu
system. There are several groups of related functions, with each group
selectable from the Main menu as shown below. Press the MENU button on
the remote control or on the built-in keypad on the rear of the projector to
display the main menu.
Use the arrow keys to navigate within the menu and adjust a setting up or
down.
Press ENTER to select a highlighted menu item or use it to change or
accept a value.
Select the next item that you want to adjust in the menu and adjust it as
described above.
Press EXIT to return to the previous menu or exit menus if at top level.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
4.1
Size and Position Menu
Size Presets
Display an image with the detected size, or resize the image by maximizing
either the height, width or both, or resize to the maximum size possible while
keeping the original aspect ratio.
• Auto: Display with the detected size.
• Native: Display in its native resolution.
• 4:3: Retain 4:3 aspect ratio.
• Letterbox: Display with the black borders on the top and bottom.
• Full Size: Fill the screen (regardless of the source).
• Full Width: Fill display width and keep aspect ratio.
• Full Height: Fill display height and keep aspect ratio.
• Custom: Stretch the display horizontally or vertically without cutting the
image display
Overscan
Remove noise around the image. Overscan Zoom enlarges image 6% from
original size. Overscan Crop cuts 6% of active pixels in four edges of original
image.
Pixel Track
Analog RGB signals only. Steady flickering or several soft vertical stripes or
bands across the entire image indicates poor pixel tracking. Proper pixel
tracking ensures that the image quality is consistent across the screen, the
aspect ratio is maintained, and that the pixel phase can be optimized.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-2
Section 4: OPERATION
Pixel Phase
Analog RGB Signals only. Adjust pixel phase when the image still shows
shimmer or noise after pixel tracking is optimized. Pixel phase can adjust the
phase of the pixel-sampling clock relative to the incoming signal.
Horz Position
Move the image right or left within the area of available pixels.
Vert Position
Move the image up or down within the area of available pixels.
Digital Horz Zoom
Change the size of projector's display area horizontally. If the display area has
been resized by this setting, it can be moved by changing the Digital Horz Shift
and Digital Vert Shift settings.
Digital Vert Zoom
Change the size of projector's display area vertically. If the display area has
been resized by this setting, it can be moved by changing the Digital Horz Shift
and Digital Vert Shift settings.
Digital Horz Shift
Move the display area horizontally if its size has been changed by the Digital
Zoom setting.
Digital Vert Shift
Move the display area vertically if its size has been changed by the Digital
Zoom setting.
Geometry Correction
The "Geometry Correction" can be controlled with the options in the dropdown list:"Off/Basic" when optional Dual Processor Warp Module is not
installed, and "Off/Basic/Curve/Rotate" when optional Dual Processor Warp
Module is installed.
Geometry Correction Feature Compatibility
4-3
Warp Function
4-Corner
Curved
Surface(2x2)
Keystone
Pincushion and
Barrel
Rotation
4-Corner
--




Curved
Surface(2x2)

--
X
X
X
Keystone

X
--

X
Pincushion and
Barrel

X

--
X
Rotation

X
X
X
--
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
•
•
Off: No Geometric correction is applied to the image.
Horz Keystone: Adjust the keystone horizontally and make a more square
image. Horizontal keystone is used to correct a keystoned image shape in
which the left and right borders of the image are unequal in length, and the
top and bottom are slanted to one of the sides. This is intended for use with
horizontally on-axis applications. For horizontally offset applications, you
must use 4 Corner correction using the optional Dual Processor Warp
Module.
B
B
Ind. WXGA 1080P WUXGA
A
•
A
12.3%
10.2% 7.1%
B
7.7%
6.4%
5.2%
A
Vert Keystone: Adjust the keystone vertically and make a more square
image. Vertical keystone is used to correct a keystoned image shape in
which the left and right borders of the image are unequal in length, and the
top and bottom are slanted to one of the sides. This is intended when for
use with horizontally on-axis applications. For horizontally offset images,
you must use 4 Corner correction using the optional Dual Processor Warp
Module.
A
B
Ind.
WXGA
1080P
WUXGA
A
5.4%
4.4%
3.3%
B
10.4%
8.7%
5.4%
B
A
•
Horz Pincushion: Adjust the pincushion horizontally and make a more
square image.
Ind.
A
•
WXGA
1080P
WUXGA
A
16.0%
13.3%
8.0%
B
16.0%
13.2%
7.9%
B
Vert Pincushion: Adjust the pincushion vertically and make a more square
image.
A
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
B
Ind.
WXGA
1080P
WUXGA
A
14.7%
12.3%
11.4%
B
14.7%
12.1%
11.4%
4-4
Section 4: OPERATION
•
Pincushion/Barrel: Allow for correction for slight curved distortion from the
lens or projection surface.
Ind.
A
B
•
C
D
WXGA
1080P
WUXGA
8.38%
8.35%
8.37%
4.59%
B
3.5%
3.98%
C
6.4%
6.4%
6.5%
D
6.4%
6.4%
6.5%
4-Corner: Allow the image to be squeezed to fit an area defined by moving
each of the four corners' x and y position.
A
A
B
B
Ind. WXGA 1080P WUXGA
B
A
10.0%
8.4%
8.3%
B
9.5%
7.9%
7.0%
B
A
•
A
A
Rotation: Allow an image to be rotated - most commonly to level the image.
While the image is rotated, the software can crop any content that begins to
fall off the panel. The function will not automatically scale the image down
to prevent cropping. If scaling is required, the digital zoom function can be
used, independently of the rotation function.
A
Ind. WXGA 1080P WUXGA
A
4-5
10.0%
8.4%
8.3%
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
Auto Image
Force the projector to reacquire and lock to the input signal. This is useful
when signal quality is marginal. "Normal mode" can support all of the 4:3 input
sources.
"Wide mode" can support all of the 16:9 input source & most of the 4:3 input
source. For those 4:3 input sources not recognized by "Wide mode" (example
1400 x 1050), perform Auto Image using "normal mode".
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-6
Section 4: OPERATION
4.2
Image Settings Menu
Brightness
Adjust the intensity of the image.
Contrast
Adjust the degree of difference between the lightest and darkest parts of the
picture and change the amount of black and white in the image.
Color Space
Select a color space that has been specifically tuned for the input signal.
Useful only for analog signals and certain digital sources.
Detail
Select the edge clarity of the image.
Video Options
This function is used with video sources only.
• Color: Adjust a video image from black and white to fully saturated color.
The color setting applies to video sources only.
• Tint: Adjust the red-green color balance in the image of NTSC video
images. The tint setting applies to NTSC video sources only.
• Noise Reduction: Reduce temporal or spatial noise in the image.
• Flesh Tone Correction: Control the amount of flesh tone correction applied
to the image.
4-7
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
•
•
•
•
Video Black Level: Analyze the current input image and calculate an offset
value which is then added to the analog to digital converter black level
value. This ensures optimum black level for each analog source.
Detect Film: Control film mode detection and determine whether the
original source of the input video was film or video.
Closed Captions: Control closed caption display while audio is not muted.
If this setting is not off, audio is not muted, the source is NTSC and
contains captions on the selected channel, then the projector must display
caption text overlaid on the image.
Input Levels
VGA / Component signals only.
• Adjust the gain of the red, green, or blue channel of the image. It will affect
the black and white.
• Adjust the offset of the red, green, or blue channel of the image. It will
affect the black and white.
• Sync Threshold: (progressive signals only) If a hardware device, such as a
DVD player, is not syncing properly with the projector, select this option to
help it to sync when connected to the projector.
Picture Settings
Optimize the projector for displaying images under certain conditions, such as
presentation, video, bright, real, dicom sim, and user-definable preset. It will
affect Gamma, Sharpness,White Peaking, Overscan, Brightness, Contrast,
Color, Tint, Red Gain, Green Gain, Blue Gain, Red Offset, Green Offset, Blue
Offset.
Save to User
Adjust the image settings and select Save to User as a picture setting. You can
recall these settings in the future by selecting the User in the Picture Settings
menu. The setting of Brightness, Contrast, Color, Tint, Red Gain, Green Gain,
Blue Gain, Red Offset, Green Offset, Blue Offset, Color Temp, Gamma, Detail,
Whitepeaking and Overscan will be saved.
Image Freeze
Pause the screen image.
Advanced Image Settings
•
Gamma: Select the appropriate gamma from Video, Film, Bright, CRT, and
DICOM.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-8
Section 4: OPERATION
•
•
•
4-9
White Peaking: (video source only) Increase the brightness of whites that
are near 100%.
Color Temperature: Change the intensity of the colors. Select a listed
relative warmth value.
Edge Enhancement: Apply the edge enhancement process.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
4.3
Configuration Menu
Language
Allows you to select an available language for the OSD display, from English,
French, German, Italian, Spanish, Chinese(simplified), Japanese, Korean, and
Russian.
Lens Settings
•
•
•
•
Focus and Zoom: Adjust the focus and zoom the image in or out.
Lens Shift: Shift the lens up and down or left and right.
Lock Lens Motors: Select this function to prevent all lens motors from
moving. It will disable the Zoom, Focus, Horizontal and Vertical Position
settings, effectively locking out any changes and overriding all other lens
features. This is particularly useful to prevent accidental lens position
changes in multi-projector installations.
Lens Calibration: Calibrate the lens center
Ceiling Mount
Turn the image upside down for ceiling-mounted projection.
Rear Projection
Reverse the image so you can project from behind a translucent screen.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-10
Section 4: OPERATION
Menu Preferences
•
•
•
•
Menu Horz Position: Change the horizontal position of the OSD.
Menu Vert Position: Change the vertical position of the OSD.
Show Messages: Display status messages on the screen.
Menu Transparency: Change OSD menu background to be transparent.
NOTE:

•
•
•
As the value increases, more of the image behind the menu is visible.
Splash Screen: Choose which splash screen is to be used.
PIN Protect: The PIN (personal identification number) feature allows you to
password protect your projector. Once you enable the PIN feature, you
must enter the PIN before you can project an image.
Change PIN: Allows you to change the PIN.
Power Management
•
•
•
•
•
Standby Mode: The projector is in standby mode when connected to AC
power. (<0.5W)
AC Power On: The projector automatically turns on when electrical power
is connected.
Auto Shutdown: Automatically turns the projector off after no signals are
detected for a preset number of minutes. If an active signal is received
before the projector powers down, the image will be displayed.
Sleep Timer: Allows the projector to automatically power off after it has
been on for a specified amount of time.
High Altitude
Set high altitude mode ON/OFF.When ON, the fan will operate at high speed
to ensure sufficient air flow for high altitudes.
Communications
•
•
4-11
Network: Allow you to setup network settings.
- DHCP: Turn the DHCP ON/OFF.
- IP Address: Assign Network IP Address.
- Subnet Mask: Assign Network Subnet Mask.
- Default Gateway: Assign Network Default Gateway.
- Host Name: Display the host name.
- MAC Address: Displays network MAC Address value.
- Show Network Messages: Turn network messages ON/OFF.
- Restart Network: Restart the network.
- Network Factory Reset: Perform factory reset on the network settings.
The Projector Name, LAN IP, WLAN IP, and SNMP settings will be
reset.
Baud Rate: Select the serial port and baud rate.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
•
•
•
Serial Port Echo: Control whether the serial port echoes characters.
Serial Port Path: Select the serial port path from either RS232 or HDBaseT.
Projector Address: Set the projector address (0-9). The projector will
respond to IR remotes set either at the same address as the projector or to
IR remotes set to address 0.
Image Blending
Adjust blend widths and settings to left, right, top and/or bottom sides to create
a seamless multi-projector stitched image. (Available only when optional Dual
Processor Warp Module is installed.)
What is a Blend?
In simple terms, a blend appears as a gradient strip along an edge of a
projected image. It is darkest along the extreme edge of the image, and
lightens nearer to the rest of the image(see below).
How are Blends used?
In multiple-projector wall, complementary blends between neighboring images
can compensate for the extra "brightness" or intensity where these edges
overlap. By controlling blend width and other properties, you can achieve
uniformity across the group of images. "Visible overlaps will disappear, as
shown below"
Overlap
Proj. 1,1
Overlap
Proj. 1,2
Image
Proj. 2,1
Proj. 2,2
With edge blending:
Blend
Proj. 1,1
Proj. 1,2
Image
Proj. 2,1
Blend
Proj. 2,2
Blending regions can be defined on all sides - left, right, top and bottom. The
same gamma curve is used for all blending regions.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-12
Section 4: OPERATION
Color Matching
You may require a unique color gamut (range) for a single projector or
application, or you may need to precisely match colors across multiple
adjacent displays. Use Color Matching by Meter Adjustment or by Manual
Adjustment to define the precise hue of each primary color component (red,
green, blue and white).
The x/y coordinates for each color define its location on the standard CIE
chromaticity graph. Changing either or both of these numbers will change the
hue of the color, and modify the range of possible colors. For example,
changing the x/y coordinates for red may move the color closer to orange or
closer to violet, which will in turn affect all displayed colors having a red
component. Adjust the slide bars or enter new specific coordinates as desired
to define or change the color gamuts needed for your environment and
applications.
Enable the selected method (Meter or Manual Adjustment)- this will
automatically disable the other method. For both methods, if Auto Test Pattern
is enabled, the solid colored test pattern will be displayed according to the
menu item on which you are positioned.
• Meter Adjustment
1 Using a color meter, enter the current x and y co-ordinates of Red,
Green, Blue and White for the projector image into the Measured Data
menu. This is the reference point for the projector. The default values in
the menu are based on the average for all projectors.
2 After measuring the values for all the projectors to be matched,
calculate the target values.
3 Enter the target values for x, y and gain for each color into the Target
Data menu.
Measured
Data
Target Data
4-13
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
•
Manual Adjustment
1 Adjust color slide bars and judge image color by eye or meter. A userdefined color "adjustment" can be applied.
2 Use this submenu if you do not have specific color coordinates in mind
and will judge color performance by eye or meter. As for Meter
Adjustment, each color control actually defines new x/y coordinates for
that color and changes its hue. The main colors (red part of red, green
part of green and blue part of blue) adjust the intensity of that color
component, while the modifying colors (e.g. green part of red and blue
part of red) modify the x and y value and change the hue of that color.
At the same time the main colors also are used to control the color of
the white point.
Hot-Key Settings
Assign a different function to the hot-key on the remote control by highlighting
the function in the list and pressing ENTER. Choose a function that does not
already have a dedicated button, and assign the hot-key to that function,
allowing you to quickly and easily use the chosen function.
Service
•
•
•
•
•
•
•
•
•
Projector Info: Display current projector settings (read-only).
Factory Reset: Restore all settings to their default value. It will not reset
network but it will reset RS232.
Test Pattern: Choose the desired internal test pattern to display, or select
OFF to turn off a test pattern.
Phosphor Index: The Phosphor index synchronizes the phosphor wheel
with the filter wheel and DMD. The index defines the delay between the
wheel and the DMD. When the Phosphor index is adjusted, it will impact
the smoothness and contouring of the R/G/B gray level.
Filter Index: The Filter index synchronizes the filter wheel with the phosphor
wheel and DMD. The index defines the delay between the wheel and the
DMD. When the filter index is adjusted, it will impact the smoothness of the
white color space without contouring, similar to the phosphor index
behavior.
Error log: Show the projector error log for debug.
Mode Adjustment: Fine tune the H and V start position for a signal in the
EDID timing table and record the values in the system to override the timing
table. The settings must be "Saved to Record" before exiting the menu, or
they will be lost. To revert to original timing table settings, each setting must
be manually cleared. Factory Defaults will not clear these override settings.
Laser Diode Info: Display current laser banks status and temperature
information.
High ambient temperature warning: Show the warning message the when
the ambient temperature is over 35°C.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-14
Section 4: OPERATION
4.4
Light Source
Light Source Mode
Select Constant Power, Constant Intensity or ECO mode. When in ECO mode,
the projector will adjust to the lowest fan speed and switch the laser diode
power to the minimum setting.
Constant Power
Set the value of the laser diode power (in Watts).
Constant Intensity
Set the value for the Constant Intensity to maintain constant brightness.
The light sensor will monitor the light level and will apply more power as the
laser brightness decays naturally over time. When the laser setting reaches
maximum power of 405W, it will remain at this setting. Note that the light
sensor needs to be calibrated for Constant Intensity mode to work properly.
Calibration should be performed again after every lamp change.
Total Projector Hours
Display current total hours the projector used.
Light Sensor
Calibrate light sensor.
4-15
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
4.5
Status Menu
The read-only Status menu lists a variety of details about the standard and
optional components currently detected in the projector.
For DHD Models
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-16
Section 4: OPERATION
For DWU Models
4-17
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
For DWX Models
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-18
Section 4: OPERATION
4.6
Input Switching & PIP Menu
Main Input
From the list of active inputs, select one to be used as the main image.
PIP/PBP Input
From the list of active inputs, select one to be used as the PIP/PBP.
PIP/PBP Enable
Toggle between displaying two sources at once (Main and PIP/PBP images) or
one source only. The check box turns the PIP/PBP source ON and OFF. Refer
to Section 6.2 for the Main and PIP/PBP compatibility table.
Swap
Change the main image to PIP/PBP, and the PIP/PBP to main image.
Swapping is available only when PIP/PBP is enabled.
Size
Select the PIP/PBP size to small, medium or large.
Layout
Set the location of the PIP/PBP image on the screen.
4-19
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
NOTE:



PIP/PBP layout and size table as described below.
P : indicates primary source region (lighter color).
* : Both source regions are the same size.
PIP/PBP Size
PIP/PBP Layout
Small
PBP, Bigger Left
Over-Under, Bigger Upper
Medium
P
P
PBP, Bigger Right
P
*
P
P
Over-Under, Bigger Lower
PIP-Bottom Right
PIP-Bottom Left
*
P
P
P
Large
*P
P
P
P*
P
P
P
P
P
P
P
P
P
P
P
P
PIP-Top Left
PIP-Top Right
Timing Detection
Select timing detection mode to wide or normal. It is used to support additional
PC timings. When the projected picture is not completed, this function is used
to adjust the picture. "Normal mode" can support all of the 4:3 input sources.
"Wide mode" can support all of the 16:9 input source & most of the 4:3 input
source. For those 4:3 input sources not recognized by "Wide mode" (example
1400 x 1050), perform Auto Image using "normal mode".
Source Info
Display current source settings (read-only).
Enable Source Hot-Key
Toggle the check box to enable or disable the main source hot-key.
Source Hot-Key
Allows you to assign a different source to the hot-key. Highlight an input and
press ENTER to choose a different one.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-20
Section 4: OPERATION
Input Key
Use it to list all of the sources or change the sources.
Blank on Signal Switch
When the function is enabled, the projector will blank the screen before timing
is stable when change source.
4.7
Language Menu
Allows you to select an available language for the OSD display.
4.8
Test Pattern Menu
Choose the desired internal test pattern to display, or select OFF to turn off a
test pattern.
• OFF
• Black
• White
• Checkerboard
• Grid
• Color Bars
4-21
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
4.9
Web User Interface
4.9.1
Logging On
Open your web browser and type the IP address (in the address bar) assigned
to your projector.
1 Select the log in level from the Access type drop-down list
2 Enter the Password in the Password field
3 Select the appropriate language from the Language drop-down list.
4 Click the Press login button. The Main window appears.
4.9.2
Main Tabbed Page - General
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-22
Section 4: OPERATION
•
•
•
Control Panel
Select main source / PIP source, enable/disable PIP/PBP, change the
layout / PIP size, swap, and change the test pattern.
Projector Information Panel
Check the projector information for power status, Pic mute status, OSD
status, IP address and Mac address.
Switch Panel
Switch the on/off status of power, Pic mute, and OSD.
4.9.3
Main Tabbed Page - Status
Display the current status of light source, cooling (fans), version numbers and
signal (source) information
4-23
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
4.9.4
Main Tabbed Page - Lens
Control the focus, lens shift and zoom adjustments for the lens.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-24
Section 4: OPERATION
4.9.5
4-25
Network
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
•
•
•
•
Restart Network
Execute a Network restart. This will not change any of the network settings.
Network Factory Reset
Execute a network factory reset. Network settings will be reset to the
following default values:
- Projector Name = Christie@ + Serial Number
- Show Network Messages = ON
- LAN Settings:
- Manual
- IP Address = 192.168.0.100
- Subnet Mask = 255.255.255.0
- Default Gateway = 192.168.0.100
- WLAN Settings:
- Enabled
- Start IP = 192.168.1.100
- End IP = 192.168.1.120
- Subnet Mask = 255.255.255.0
- Default Gateway = 192.168.1.100
- SNMP Settings:
- SNMP Read Communication = private
- Trap IP Address = 0.0.0.0
- SMTP IP Address = 0.0.0.0
- All other settings are cleared/blanked
- Trap Configuration:
- All items = SNMP Trap + Email
LAN Setting Panel
- Select if the projector must obtain an automatically assigned IP address
through DHCP or if the user will set the address manually.
- Enter the IP address, netmask, and default gateway address for the
TCP/IP setting.
WLAN Setting Panel
- Select if the wireless LAN of the projector is enabled or disabled.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-26
Section 4: OPERATION
-
•
•
•
4-27
Enter the IP address range, netmask and default gateway for the wireless LAN.
SNMP Panel
- The SNMP (Simple Network Management Protocol) interface provides
network administrators with a common way to manage their network
devices from a single remote location. SNMP allows an administrator to
query a number of devices to see their current status/ configuration. It
also allows operators to change configuration values and configure trap
notifications to be sent when certain events occur. (eg. Loss of signal,
power state change, etc)
 Emails are sent to the mail server configured in the projector
settings. Up to 2 user email accounts can be selected. Any
important information regarding the event will be located in the body
content of the email.
 SNMP Traps are notifications that are sent from the projector. They
are only received by a trap receiver (MIB Browser) in the computer.
- SNMP Read Community (default setting: private) - this is a plain- text
password. This must also be entered in the MIB browser. This password allows the various settings in the projector to be queried.
- SNMP Location (default setting: blank) - This field can be used as a
description to where a projector is located in a building. SNMP emails
sent will specify this location.
- Trap IP Address (default setting: 0.0.0.0) - This field must be filled in to
receive Traps from the projector. The Trap IP Address should be filled in
with the IP Address of the computer on which you would like to view
received traps.
- Trap Email 1/2 (default setting: Blank) - The Trap Email 1 and 2 must be
set to an email address that is configured under the mail server that you
will enter in the "SMTP Server IP Address" field.
- Email from Address (default setting: blank) - the "Email from Address"
that will appear as the source of the SNMP emails.
- SMTP Server IP Address (default setting: 0.0.0.0) - Enter your mail
server's IP address.
Trap Configuration Panel
Set the SNMP actions for the system events. The dropdown options are:
SNMP Trap + Email, Email, SNMP Trap, and Disabled.
Crestron Control System Panel
Enter the IP address, IP ID, and Port of Crestron device for connection.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
4.9.6
Tools
To Use the Tools tabbed pages to control "Size & Position", "Image Settings",
"Configuration", "Light Source", "Input Switching & PIP" and "Test Pattern.
4.9.7
Administrator Page
Add or delete a user or change password
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-28
Section 4: OPERATION
4.9.8
•
•
4-29
About Page
Version Tab
View the main firmware version, network firmware version, projector model
name, and projector serial number.
License Tab
The license information of the computer program is displayed.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
4.10
Christie Presenter
The Christie Presenter application allows a remote desktop from a host PC to
be displayed on the network display through Ethernet, USB, or wireless
transports. It can adapt to different network settings (DHCP, fixed IP, and direct
link by USB/Ethernet cable).
Christie Presenter can be downloaded from the Christie website or from the
web page of the projector.
4.10.1 Connect to the Projector
1. Connect to the projector using WiFi or Ethernet
- Ethernet connection:
 Determine the projector's IP address from the menu Main Menu >
Configuration > Communications > LAN

-
Configure your PC IP address to be on the same network as the
projector.
 The projector and computer must be connected directly or over the
network via Ethernet.
WiFi Wireless connection:
 Insert the WiFi USB dongle (1DWUSB-BGN) into the USB port on
the projector input panel.
HDBaseT
REMOTE
IN
REMOTE
OUT
HDMI
VGA IN
VGA OUT
DISPLAY PORT
DVI
MINI USB
GREEN/Y
BLUE/PB
RED/PR
RS232
USB
ETHERNET
CVBS
S-VIDEO
K
Insert the WiFi USB dongle
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-30
Section 4: OPERATION



Power on the Projector.
Obtain the WiFi SSID from the OSD menu Main Menu >
Configuration > Communications > WLAN
Connect your PC device to the wireless SSID for the selected
projector . Example: "Christie@0111000123".
4.10.2 Install Christie Presenter software
1. Use a web browser to connect to the projector's network address (Default
address 192.168.1.100)
2. Download and install the Christie Presenter Software
4-31
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
3. Configure the Christie Presenter Software. The name entered is used to
identify all computers connected to the projector via the Christie Presenter
software via either wired or wireless connections. The Network Display
Management -> Device Management tab will show all current connections.
4.10.3 Use Christie Presenter
1. Press the autorun icon in the system tray to pause or play the USB display.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-32
Section 4: OPERATION
2. After starting the Christie Presenter application, the main window can been
seen (shown below).
Icon
Description
Connect and search network display
Stop/start displaying desktop contents to
connected network display
Select display region
Configure Christie Presenter
Manage all connected network displays
Disconnect all connections
Connect and search network display
1
4-33
Click the button
to enter into the connection menu section.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
2
If the IP address of the projector is known, enter the IP address and
click the "Connect" button. If the IP address is not known, click the
"Search" button to search for the projector on the network and select
the projector to which you want to connect. Select the option "Directly"
in order to proceed to the log in interface.
3
Input "User type" and "Password" in the log-in interface. Select the
display port (the default is full screen). Obtain the " Normal " user's
password from the OSD menu Main Menu > Configuration >
Communications > WLAN.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-34
Section 4: OPERATION
Select display region
Once the connection is set up, click the button
to select the size of
the projection region: FullScreen, FixedSize, or Alterable.
•
•
•
4-35
FullScreen: The default capture mode turns to Full screen when the
program is launched. At that time, if screen capture starts, the image of the
whole screen is transferred to a remote network display.
FixedSize: FixedSize mode allows the users to place a frame on the
desktop. Only the image enclosed inside the frame is transferred to remote
network display.
Alterable: In Alterable mode the only region captured is the one enclosed
by the frame. The region can be enlarged or downsized by dragging the
eight small black squares scattered on eight edges of the frame.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
Configure Christie Presenter
Click the button
to configure Christie Presenter for Basic Setting
and Advanced Setting.
•
•
Basic Setting: Select language, change the region size of fixed size
capture mode, and select if notification message popup is allowed.
Advanced Setting: Select the quality of JPEG image, YUV sample format
and network port setting. (The "Fixed" port is Port 5900)
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-36
Section 4: OPERATION
Manage all connected network displays
Click the button
to control all the users and all the projectors
connector to the same projector.
con
Icon
Description
Administrator log in.
Normal user log in.
Device is connected.
Device is not connected.
The icon shows the current status and display
position of the local screen on the network
display. Click on the icon to change the display
position. A dialog box will appear.
Click this unlock icon to change the password.
(Password change to target network display. Only
an Administrator user can change the password.)
No response is expected when this icon is
clicked. If user log in as "Admin", the key icon can
be seen and the Presenter password can be
changed. If user log in as "Normal", the lock icon
can be seen and the Presenter password can't be
changed.
Disconnect from target network display.
Link for connecting to a target network display via
a webpage.
4-37
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
4.11
Card Reader Operation
There are four operation modes in the Card Reader application:
- USB Flash Devices Detection Screen
- Thumbnail Display Mode
- Images Display Mode
- Images Slide Show Mode
1. USB Flash Device Detection Screen:
In this mode, the Card Reader application detects any USB flash devices
hot-plug events and displays the flash device icon. When the flash device is
removed from USB, the icon disappears. It is suggested that USB flash
devices should be removed only when the Card Reader is changed to the
USB Flash Devices Detection Screen state.
2. Thumbnail Display Mode:
Press the Enter key to enter the Thumbnail Display Mode. Different photos
in different folders can be chosen. Press the Menu key to bring up the Card
Reader operation UI.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-38
Section 4: OPERATION
•
•
•
•
•
•
•
•
•
•
•
The user interface is designed to operate the card reader application with a
few keys (Enter/Left/Right/Up/Down).
The following buttons are supported in the user interface:
Previous: Move the selected item left. (Go to previous page when this is the
leftmost item)
Next: Move the selected item right. (Go to next page when this is the
rightmost item.)
Display: Display the selected image or display the selected folder.
Thumbnail: Enter the Thumbnail Display Mode.
SlideShow: Enter the Slide Show Mode.
NameOrder: Sort files/folders in name order.
ExtendOrder: Sort files/folders in extended order.
SizeOrder: Sort files/folders in size order.
TimeOrder: Sort files/folders in time order.
EXIF ON/OFF: Enable/Disable auto image rotate accordingly to EXIF
information.
FileName ON/OFF: Enable/Disable filename display in Thumbnail Display
Mode.
3. Image Display Mode:
Press the ENTER key in the Thumbnail Display Mode to enter the Image
Display Mode; press the SlideShow key to enter the Slide Show Mode. The
Left/Right key is used to display the last/next image in the Image Display
Mode. In the Image Display Mode, press the ENTER key to quit from the
Image Display Mode and enter the Thumbnail Display Mode.
In the Slide Show Mode, press the ENTER key to enter the Image Display
Mode.
The alternative way to display image in the Image Display Mode or Slide
Show Mode is using the operation UI.
4-39
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
•
•
•
•
•
•
•
•
The following operations are supported in the operation UI.
Display: Enter the Image Display Mode.
Thumbnail: Enter the Thumbnail Display Mode.
SlideShow: Enter the Slide Show Mode.
Actual Size: Display in actual size of the image.
Best Fit: Display the image in best fit to the screen.
EXIFDisp OFF/On: Enable/Disable EXIF information display.
+90deg: Rotate 90 degree.
-90deg: Rotate -90 degree.
4. Image Slide Show Mode:
The following operations are supported in the Slide Show Mode operation
UI.
• Stop: Stop Slide Show Mode.
• Next: Display next image.
• Previous: Display previous image.
• Delay 3/4/5: Slide Show delay in seconds.
• Slide Effect: Following modes are supported.
- Slide Right
- Blocks
- RightDown
- XLines
- Slide Up
- Ylines
- Repeat ON/OFF: Enable/Disable Slide Show Repeat Mode.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-40
Section 4: OPERATION
When the image can NOT be displayed due to memory limitation or can
NOT support image format, the specific image is displayed on the center of
the screen.
4-41
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 4: OPERATION
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
4-42
Section 5: TROUBLESHOOTING
5.
TROUBLESHOOTING
If you are unable to resolve an issue using the information provided in this
section, contact your reseller or service center.
Problem
-
•
Solution
No image appears on-screen
Make sure all the cables and power connections are
correctly and securely connected See "Installation".
-
Check if the Light Status LED is in Green.
-
Make sure you have removed the lens cap and the
projector is switched ON.
Partial, scrolling or incorrectly
displayed image
Press "AUTO" on control panel or on remote control.
If you are using a PC (for Windows 95, 98, 2000, XP,
Windows 7):
1. Click the "My Computer" > "Control Panel" and then
double - click "Display".
2. Select the "Settings" tab.
3. Verify that your display resolution setting is lower than
or equal to WUXGA (1920 × 1200).
4. Click on the "Advanced Properties" button. If the
projector is still not projecting the whole image, change
the monitor display:
4.1 Verify the resolution setting is lower than or equal to
WUXGA (1920 × 1200).
4.2 Select the "Change" button under the "Monitor" tab.
4.3 Click on "Show all devices". Next, select "Standard
monitor types" under the SP box; choose the
resolution mode you need under the "Models" box.
4.4 Verify that the resolution setting of the monitor
display is lower than or equal to WUXGA (1920 ×
1200).
5-1
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 5: TROUBLESHOOTING
Problem
-
Solution
Partial, scrolling or incorrectly
displayed image
If you are using a Notebook:
1. Adjust resolution of the computer.
2. Press the keys listed below for your notebook
manufacturer to send signal out from notebook to
projector. Example: [Fn]+[F4]
Notebook Brand
Function Keys
Acer
[Fn]+[F5]
Asus
[Fn]+[F8]
Dell
[Fn]+[F8]
Gateway
[Fn]+[F4]
IBM/Lenovo
[Fn]+[F7]
HP/Compaq
[Fn]+[F4]
NEC
[Fn]+[F3]
Toshiba
[Fn]+[F5]
Mac Apple
System Preference  Display 
Arrangement  Mirror display
-
If you experience difficulty changing resolutions or your
monitor freezes, restart all equipment including the
projector.
•
The screen of the
Notebook or
PowerBook
computer is not
displaying your
presentation
-
If you are using a Notebook PC
Some Notebook PCs may deactivate their own screens
when a second display device is in use. Each of them has a
different method of reactivation. Please refer to your
computer manual for detailed information.
•
Image is unstable
or flickering
-
Use "Pixel Track" and "Pixel Phase" to correct it.
-
Change the monitor color setting on your computer.
•
Image has vertical flickering bar
-
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Use "Auto Image" to make an adjustment.
Check and reconfigure the display mode of your graphic
card to make it compatible with the projector.
5-2
Section 5: TROUBLESHOOTING
Problem
•
•
•
5-3
Image is out of
focus
The image is
stretched when
displaying 16:9
DVD title
Solution
-
Make sure both lens caps (front and back) are removed.
-
Adjust lens focus to fit.
-
Make sure the projection screen is between the required
distance.
-
When you play anamorphic DVD or 16:9 DVD, the
projector will show the best image when the projector
display mode is set to 16:9 in the OSD.
-
If you play 4:3 format DVD titles, please change the format
to 4:3 in the projector OSD.
-
If the image is still stretched, you will also need to adjust the
aspect ratio by setting the display format as 16:9 (wide)
aspect ratio type on your DVD player.
Image is too small or too large
-
Adjust lens zoom to fit.
If it does not fill the screen properly, verify that the correct
lens is in use or change the position of the projector.
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 5: TROUBLESHOOTING
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
5-4
Section 6: SPECIFICATIONS
6.
SPECIFICATIONS
6.1
Inputs
Signal
Type
Resolution
Frame Rate
(Hz)
HDMI
640x350
85
●
640x400
85
●
640x480
59
●
640x480
60
●
●
640x480
72
●
●
640x480
75
●
●
●
●
640x480
85
●
●
●
●
720x400
85
●
●
768x480
60
●
768x480
75
●
768x480
85
●
800x600
50
●
800x600
56
●
●
800x600
60
●
●
800x600
72
●
●
800x600
75
●
●
●
●
800x600
85
●
●
●
●
848x480
50
●
848x480
60
●
848x480
75
●
848x480
85
●
960x600
50
●
960x600
60
●
960x600
75
●
VGA
DisplayPort
DVI
Component
S- video
CVBS
●
●
●
●
●
●
●
●
PC
●
●
●
●
●
NOTE:

6-1
"RB" means "reduced blanking".
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 6: SPECIFICATIONS
Signal
Type
PC
Resolution
Frame Rate
(Hz)
HDMI
960x600
85
●
1024x768
60
1024x768
VGA
DisplayPort
DVI
●
●
●
●
75
●
●
●
●
1024x768
85
●
●
●
●
1064x600
50
●
1064x600
60
●
1064x600
75
●
●
1064x600
85
●
●
1152x720
50
●
1152x720
60
●
1152x720
75
●
1152x720
85
●
1152x864
60
●
●
●
1152x864
70
●
●
●
1152x864
75
●
●
●
1152x864
85
●
●
●
1280x720
50
●
1280x720
60
●
●
●
●
1280x720
75
●
●
●
●
1280x720
85
●
●
●
●
1280x768
60
●
●
●
1280x768
75
●
●
●
1280x768
85
●
●
●
1280x800
50
●
●
●
●
1280x800
60
●
●
●
●
1280x800
75
●
●
●
1280x800
85
●
●
●
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Component
S- video
CVBS
●
●
6-2
Section 6: SPECIFICATIONS
Signal
Type
PC
6-3
Resolution
Frame Rate
(Hz)
HDMI
VGA
1280x960
60
●
●
●
1280x960
75
●
●
●
1280x960
85
●
●
●
1280x1024
50
●
1280x1024
60
●
●
●
●
1280x1024
75
●
●
●
●
1280x1024
85
●
●
●
●
1360x768
50
●
1360x768
60
●
1360x768
75
●
1360x768
85
●
1366x768
60
●
●
●
●
1400x900
60
●
●
●
●
1400x1050
50
●
1400x1050
60
●
●
1400x1050
75
●
●
●
1440x900
60
●
●
●
1440x900
75
●
1600x900
60
●
1600x1200
50
●
1600x1200
60
●
1680x1050
50
●
1680x1050
60
●
1680x1050
75
●
1704x960
50
●
1704x960
60
●
1728x1080
50
●
DisplayPort
DVI
Component
S- video
CVBS
●
●
●
●
●
●
●
●
●
●
●
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 6: SPECIFICATIONS
Signal
Type
PC
NTSC
PAL
SECAM
Resolution
Frame Rate
(Hz)
HDMI
1728x1080
60
●
1864x1050
50
●
1864x1050
60
●
1920X1080
50
●
1920X1080
60
●
●
1920X1200RB
60
●
●
●
●
1920X1200RB
50
●
●
●
●
NTSC (M, 4.43)
VGA
DisplayPort
DVI
Component
S- video
CVBS
60
●
●
PAL (B,G,H,I)
50
●
●
PAL (N)
50
●
●
PAL (M)
60
●
●
SECAM (M)
50
●
●
480i
60
●
●
●
●
576i
50
●
●
●
●
480p
60
●
●
●
●
576p
50
●
●
●
●
●
●
EDTV
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
6-4
Section 6: SPECIFICATIONS
Signal
Type
Resolution
Frame Rate
(Hz)
HDMI
VGA
1080i
25
●
1080i
29
1080i
DisplayPort
DVI
Component
●
●
●
●
●
●
●
30
●
●
●
●
720p
50
●
●
●
●
720p
59
●
●
●
●
720p
60
●
●
●
●
1080s
23
●
●
1080s
24
●
●
1080p
23
●
●
●
●
1080p
24
●
●
●
●
1080p
25
●
●
●
●
1080p
29
●
●
●
●
1080p
30
●
●
●
●
1080p
50
●
●
●
●
1080p
59
●
●
●
●
1080p
60
●
●
●
●
S- video
CVBS
HDTV
6-5
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 6: SPECIFICATIONS
6.2
PIP/PBP Compatibility
Main
HDMI
VGA
Component
CVBS
S-Video
HDBaseT
DisplayPort
USB A
USB
MINI-B
RJ45
DVI-D
HDMI
-
-
-
-
-
-
●
●
●
●
●
VGA
-
-
-
-
-
-
●
●
●
●
●
Component
-
-
-
-
-
-
●
●
●
●
●
CVBS
-
-
-
-
-
-
●
●
●
●
●
S-Video
-
-
-
-
-
-
●
●
●
●
●
HDBaseT
-
-
-
-
-
-
●
●
●
●
●
DisplayPort
●
●
●
●
●
●
-
-
-
-
-
USB A
●
●
●
●
●
●
-
-
-
-
-
USB MINI-B
●
●
●
●
●
●
-
-
-
-
-
RJ45
●
●
●
●
●
●
-
-
-
-
-
DVI-D
●
●
●
●
●
●
-
-
-
-
-
PIP/PBP
● : PIP/PBP combinations are enabled
- : PIP/PBP combinations are disabled
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
6-6
Section 6: SPECIFICATIONS
6.3
Key Features
•
•
WXGA 0.65" 1280 x 800 or HD 0.65" 1920 × 1080 resolution or WUXGA
0.67" 1920 × 1200 resolution
Projection lens compatibility:
- Horizontal offset ranges: +/-30%
- Vertical offset ranges: +/-100% (WUXGA/WXGA) and +/-120% (HD)
NOTE:

•
•
•
•
•
•
•
•
6-7
Measurements are based on industry standards where offset is calculated as a ratio of the number of pixels shifted up/
down to half the image size.
Dual Processing Warp Module for edge blending and geometric correction.
(Optional)
Wireless desktop display using wireless dongle (optional)
SNMP traps and e-mail notifications
10-bit image processor electronics with modular design
All video formats can be resized to full screen either horizontally or
vertically while maintaining aspect ratio
The projector can be operated using any of the following:
- The built-in keypad, an infrared (IR) remote control, a wired remote
control, a PC/device using serial communications (Ethernet or RS232)
- A Web page via Ethernet or from a PC/device via a wireless USB
dongle. (Optional)
Weight:
- Maximum product weight (with lens removed): 15kg (33lb.)
Built-In keypad
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 6: SPECIFICATIONS
6.4
List of Components
This projector comes with all the items shown below. Check to make sure your
package is complete. Contact your dealer if anything is missing.
•
•
•
•
IR remote control 003-004468-01
Power cord x 4
- UK/Korea/Russia
- North America
- Europe
- Japan
DVI to HDMI dongle
User manual (CD)
NOTE:

6.5
Due to the difference in applications for each country, some regions may have different accessories.
Optional Accessories
•
•
•
•
•
•
•
Cable cover (140-103105-01)
Standard Lens (A05) (140-100102-01)
Optional Lens (A01) (140-101103-01)
Optional Lens (A03) (140-102104-01)
1DWUSB-BGN / Wireless dongle (optional accessory) (133-113106-01)
Dual Processor Warp Module (optional accessory) (133-111104-01)
Portrait Side Cover (140-108100-01)
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
6-8
Section 6: SPECIFICATIONS
6.6
REGULATORY
•
•
Safety
- CSA C22.2 No. 60950-1
- UL 60950-1
- IEC 60950-1
- EN 60950-1
Electro-Magnetic Compatibility
Emissions
-
FCC CFR47, Part 15, Subpart B/ANSI C63.4, Class A - Unintentional
Radiators
CISPR 22/EN55022 Class A - Information Technology Equipment
ICES/NMB003 (A) - Information Technology Equipment
Immunity
-
•
•
•
6-9
CISPR 24/EN55024 EMC Requirements - Information Technology
Equipment
Environmental
The product conforms to:
- EU Directive (2011/65/EU) on the restriction of the use of certain
hazardous substances (RoHS) in electrical and electronic equipment
and the applicable official amendment(s).
- EU Regulation (EC) No. 1907/2006 on the registration, evaluation,
authorization and restriction of chemicals (REACH) and the applicable
official amendment(s).
- EU Directive (2012/19/EU) on waste and electrical and electronic
- equipment (WEEE) and the applicable official amendment(s).
- China Ministry of Information Industry Order No.39 (02/2006) on the
control of pollution caused by electronic information products, the
hazardous substances concentration limits (SJ/T11363-2006), and the
applicable product marking requirement (SJ/T11364-2006).
Marking
- This product conforms to all relevant Canadian, US, and European
directives, standards, safety, health and environmental concerns.
International packaging recycling marks conform to:
 EU Directive (2012/19/EU) on waste and electrical and electronic
equipment (WEEE) .
 EU Directive (94/62/EC) on packaging and packaging waste
 China packaging recycling mark standard (GB18455-2001)
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 6: SPECIFICATIONS
6.7
Federal Communications Commission (FCC) Warning
WARNING
A shielded-type power cord is required in order to meet FCC emission limits
and also to prevent interference to the nearby radio and television
reception. It is essential that only the supplied power cord be used.
• Use only shielded signal cables to connect I/O devices to this equipment.
•
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
6-10
Section 6: SPECIFICATIONS
6.8
OSD Tree
Level 1
Level 2
Level 3(Or List)
Level 4(Or List)
Level 5(Or List)
Level 6(Or List)
Default
Auto
Native
4:3
Size Presets
Auto
Letterbox
Full Size
Full Width
Full Height
Custom
Off
Overscan
Zoom
By source set
Crop
Pixel Track
0 - 100
50
Pixel Phase
0 - 100
50
Horz Position
0 - 100
50
Vert Position
0 - 100
50
Digital Horz Zoom
50%~400%
100
Digital Vert Zoom
50%~400%
100
Digital Horz Shift
0 - 100
50
Digital Vert Shift
0 - 100
50
Off
Off
Size & Position
Horz Keystone
0 - 100
(0-20 for GEO
model)
50
(10 for GEO
model)
Vert Keystone
0 - 100
(0-20 for GEO
model)
50
(10 for GEO
model)
Horz Pincushion
0 - 100
50
Vert Pincushion
0 - 100
50
Pincushion/Barrel
0-20
10
Basic
4-Corner
Geometry Correction
Curve
Curve
4-Corner
6-11
Top Left Horz
adjust.
0-140
0
Top Left Vert
adjust.
0-80
0
Top Right Horz
adjust.
0-140
0
Top Right Vert
adjust.
0-80
0
Bottom Left Horz
adjust.
0-140
0
Bottom Left Vert
adjust.
0-80
0
Bottom Right
Horz adjust.
0-140
0
Bottom Right Vert
adjust.
0-80
0
Top Arc
0-300
150
Bottom Arc
0-300
150
Left Arc
0-300
150
Right Arc
0-300
150
Top Left Horz
adjust.
0-140
0
Top Left Vert
adjust.
0-80
0
Top Right Horz
adjust.
0-140
0
Top Right Vert
adjust.
0-80
0
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 6: SPECIFICATIONS
Level 1
Level 2
Level 3(Or List)
Curve
Level 4(Or List)
4-Corner
Rotation
Level 5(Or List)
Level 6(Or List)
Default
Bottom Left Horz
adjust.
0-140
0
Bottom Left Vert
adjust.
0-80
0
Bottom Right
Horz adjust.
0-140
0
Bottom Right Vert
adjust.
0-80
0
0-16
Top Left Horz
adjust.
Size & Position
Geometry Correction
Rotate
4-Corner
8
0-140
0
Top Left Vert
adjust.
0-80
0
Top Right Horz
adjust.
0-140
0
Top Right Vert
adjust.
0-80
0
Bottom Left Horz
adjust.
0-140
0
Bottom Left Vert
adjust.
0-80
0
Bottom Right
Horz adjust.
0-140
0
Bottom Right Vert
adjust.
0-80
0
Auto Image
Brightness
0 - 100
50
Contrast
0 - 100
By source set
Auto
Auto
RGB
Color Space
RGB
RGB Video
RGB
REC709
YUV
REC709
REC601
REC709
Maximum
High
Detail
Normal
By source set
Low
Minimum
Image settings
Video Options
Color
0 - 100
50
Tint
0 - 100
50
Noise Reduction
0 - 100
0
Flesh Tone Correction
0 - 100
0
Off/On
Off
Video Black Level
Detect Film
Off
Closed captions
cc1
Off
cc2
Input Levels
Red Gain
0 - 100
50
Green Gain
0 - 100
50
Blue Gain
0 - 100
50
Red Offset
0 - 100
50
Green Offset
0 - 100
50
Blue Offset
0 - 100
50
Sync Threshold
0 - 100
50
Reset RGB Gain/
Offset
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
6-12
Section 6: SPECIFICATIONS
Level 1
Level 2
Level 3(Or List)
Level 4(Or List)
Level 5(Or List)
Level 6(Or List)
Default
Presentation
Video
Picture Settings
Bright
By source set
Real
DICOM SIM
User
Save to User
Image Freeze
Off / On
Off
Video
Film
Gamma
Bright
By source set
CRT
Image settings
DICOM
White Peaking
0 - 100
By source set
Warmest
Advanced Image
Settings
Color Temperature
Warm
Cool
By source set
Bright
Off
Edge Enhancement
Normal
Off
Maximum
Off
Color Enhancement
CE 1
Off
CE 2
Language
Lens settings
English
Focus
command
Zoom
command
Lens Shift
command
Lock all Lens
Motors
Locked
Lens center calibration
Ceiling Mount
Off/On/Auto
Rear Projection
Off/On
Configuration
Allow
Allow
command
Auto
Off
Menu Horz Offset
0 - 100
0
Menu Vert Offset
0 - 100
0
Show Messages
off/on
Menu Transparency
0 - 90
0
Factory Logo
Menu Preferences
Splash Screen
Setup
Blue
Black
Factory Logo
White
6-13
PIN Protect
command
Change PIN
command
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 6: SPECIFICATIONS
Level 1
Level 2
Level 3(Or List)
Level 4(Or List)
0.5 W Mode
Standby Mode
AC Power On
Communication
Mode
off/on
Level 5(Or List)
Level 6(Or List)
Default
Communication
mode
Off
Never
5 Mins
10 Mins
Power Management
Auto shutdown
15 Mins
20 Mins
20 Mins
25 Mins
30 Mins
Off
Sleep Timer
2 Hrs
4 Hrs
Off
6 Hrs
High Altitude
Off/On
Off
DHCP
IP Address
LAN
Subnet Mask
by set
Default Gateway
MAC Address
Enable
Start IP
End IP
WLAN
Subnet Mask
Default Gateway
by set
MAC Address
Configuration
SSID
Password
Projector Name
Communications
Network
Show Network
Messages
Restart Network…
by set
Network Factory
Reset…
2400
4800
9600
14400
Serial Port Baud
Rate
19200
115200
38400
57600
115200
1200
Serial Port Echo
Serial Port Path
Image Blending
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Off/On
RS232
HDBaseT
Off
RS232
Projector Address
0-9
0
Blending
On/Off
Off
Marker
On/Off
Off
Grid
Off/White/Red/
Green/Blue
Off
Solid Color
Off/White/Red/
Green/Blue
Off
6-14
Section 6: SPECIFICATIONS
Level 1
Level 2
Level 3(Or List)
Level 4(Or List)
Level 5(Or List)
TOP
0… ½ Output
Height(Pixel)
0
Bottom
0… ½ Output
Height
0
Left
0… ½ Output
Width
0
Right
0… ½ Output
Width
0
Blending Area offset
0-2000
1000
non-Blending
Area Offset
0-2000
1000
Overlap
Image Blending
Bright Adj.
Drop Off Curve
70-300
Image Gamma
1.8/2.0/2.2/2.4/2.6
2.2
Off
Auto Test Pattern
On/Off
On
Color Matching
Target Data
6-15
100
On/Off
Meter Adjustment
Manual Adjustment
Default
Enable
Measured Data
Configuration
Level 6(Or List)
Intensity of Red
100 - 10000
544
x of Red
0.300 - 0.700
0.590
0.383
y of Red
0.300 - 0.500
Intensity of Green
100 - 10000
2103
x of Green
0.300 - 0.400
0.314
0.620
y of Green
0.400 - 0.700
Intensity of Blue
100 - 10000
124
x of Blue
0.100 - 0.300
0.146
0.030
y of Blue
0.030 - 0.400
Intensity of White
100 - 10000
6772
x of White
0.200 - 0.400
0.305
y of White
0.200 - 0.400
0.333
Reset to Default
Yes/No
Gain of Red
0.200 - 1.000
1.000
x of Red
0.300 - 0.700
0.615
0.381
y of Red
0.300 - 0.500
Gain of Green
0.200 - 1.000
1.000
x of Green
0.300 - 0.400
0.308
y of Green
0.400 - 0.700
0.633
Gain of Blue
0.200 - 1.000
1.000
x of Blue
0.100 - 0.300
0.142
y of Blue
0.030 - 0.400
0.030
Gain of White
0.200 - 1.000
1.000
x of White
0.200 - 0.400
0.328
y of White
0.200 - 0.400
0.380
Reset to Default
Yes/No
Enable
On/Off
Off
Auto Test Pattern
On/Off
On
1000
Red Part of Red
0 - 1000
Green Part of Red
0 - 1000
0
Blue Part of Red
0 - 1000
0
Green Part of
Green
0 - 1000
1000
Red Part of
Green
0 - 1000
0
Blue Part of
Green
0 - 1000
0
Blue Part of Blue
0 - 1000
1000
Red Part of Blue
0 - 1000
0
Green Part of Blue
0 - 1000
0
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 6: SPECIFICATIONS
Level 1
Level 2
Color Matching
Level 3(Or List)
Manual Adjustment
Level 4(Or List)
Level 5(Or List)
Red Part of White
0 - 1000
Level 6(Or List)
Default
1000
Green Part of
White
0 - 1000
1000
Blue Part of White
0 - 1000
1000
Reset to Default
Yes/No
Blank Screen
Aspect Ratio
Hot-Key settings
Freeze Screen
Projector Info
Overscan
Closed Captions
Model Name
Serial Number
Native Resolution
Firmware
Projector Info
Configuration
Boot Code
Standby Mode
Lens Lock Settings
Wheel Index
FactoryReset…
Off
Grid
White
Configuration
Black
Checkerboard
Color Bars
Test pattern
Red
Green
Blue
Service
Yellow
Magenta
Cyan
Boresight
Phosphor Index
Filter Index
Error log
Show log
Clear log
Mode Adjustment
LD1 Voltage
LD2 Voltage
LD3 Voltage
LD4 Voltage
Laser Diode Info
LD5 Voltage
Bank1 temperature
Bank2 temperature
High ambient temperature warning
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
On/Off
On
6-16
Section 6: SPECIFICATIONS
Level 1
Level 2
Level 3(Or List)
Light Source Mode
Constant Power/
Constant Intensity/Eco mode
Level 4(Or List)
Constant Power
Constant Power
243 - 405
243, 259, 275,
292, 308, 324,
340, 356, 373,
389, 405
Constant Intensity
0 - 10
7
Light Source
Level 5(Or List)
Level 6(Or List)
Default
Total Projector
Hours
Light Sensor
Light Sensor Calibration
Calibrated?
(display Yes/No)
Model Name
Serial Number
Native Resolution
Firmware
Vxx, Ayy, Bzz
Main Input
Main Signal Format
Main Pixel Clock
Main Sync Type
Main Horz Refresh
Main Vert Refresh
PIP/PBP Input
PIP/PBP Signal
Format
Status
PIP/PBP Pixel
Clock
PIP/PBP Sync
Type
PIP/PBP Horz
Refresh
PIP/PBP Vert
Refresh
Light Source Power
Total Projector
Hours
Standby Mode
Lens Lock Settings
IP Address
DHCP
System Temperature
6-17
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 6: SPECIFICATIONS
Level 1
Level 2
Level 3(Or List)
Main Input
SPEC define
PIP/PBP Input
SPEC define
PIP/PBP Enable
Level 4(Or List)
OFF
Level 5(Or List)
Level 6(Or List)
Default
OFF
ON
Swap
Size
(Small/Medium/
Large)
Main Layout
(PBP, Main Left /
PBP, Main Top /
PBP, Main Right /
PBP, Main Bottom / PIP-Bottom
Right / PIP-Bottom Left / PIP-Top
Left / PIP-Top
Right)
Timing Detection
Mode
Normal
Wide
Wide
Active Source
Signal Format
Aspect Ratio
Resolution
Vert Refresh
Horz Refresh
Source Info
Input Switching & PIP
Pixel Clock
Sync Type
Color Space
Enable source HotKey
Source Hot-Key
PIP/PBP
(When PIP/PBP
active)
<PIP/PBP source
lines>
(When PIP/PBP
active)
ON
OFF
ON
VGA
Key number 1
HDMI
Key number 2
DVI-D
Key number 3
Display Port
Key number 4
Component
Key number 5
S-Video
Key number 6
Composite
Key number 7
Christie Presenter
Key number 8
Card Reader
Key number 9
Mini USB
Key number 0
HDBaseT
Change Sources
Input key
List all Sources
Auto Source
Auto Source
Blank on Signal
Switch
Language
OFF
ON
OFF
English
Off
Grid
White
Test pattern
Black
Checkerboard
Color Bars
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
6-18
Section 6: SPECIFICATIONS
6.9
Preset Mode tables
Orion-Laser projector
Descrption
Bright
Presentation
Video
Dicom
PW
2X
2X
2X
2X
Real
2X
CW
2X
2X
2X
2X
2X
Syt. mode number
0
6
6
6
6
color temperature
Warm
Bright
Warm
Warm
Warm
Bright
Warm
Please see below table for DWU/DHD & DWX
Warmest
Cool
Gamma
Video
Video
Video
Dicom
FILM
White peaking
100
100
100
100
100
Mode
NO.
0
6-19
SQ
Bright
CT mode
2X-Native
OSD mode
CT
Bright
Warm
0
Bright
2X-D55
Bright
Warmest
0
Bright
2X-D70
Bright
Bright
0
Bright
2X-D80
Bright
Cool
1
Presentation
2X-Native
Presentation
Bright
1
Presentation
2X-D65
Presentation
Warm
1
Presentation
2X-D55
Presentation
Warmest
1
Presentation
2X-D85
Presentation
Cool
2
Video
2X-Native
Video
Warm
2
Video
2X-D55
Video
Warmest
2
Video
2X-D75
Video
Bright
2
Video
2X-D85
Video
Cool
3
Real
2X-Native
Real
Warm
3
Real
2X-D55
Real
Warmest
3
Real
2X-D75
Real
Bright
3
Real
2X-D85
Real
Cool
OSD
Gamma index
CRT
6
VIDEO
5
FILM
0
BRIGHT
4
DICOM
13
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Section 6: SPECIFICATIONS
SIGNAL
Composite
S-video
VGA/PC
HDMI/DVI/
HDBaseT
Default
Mode
Video
Mode
Video
Mode
IMAGE
PAL
PAL
Presenta- PC Sigtion Mode
nal
Presenta- PC Sigtion Mode
nal
GS Series User Manual
020-000724-01 Rev. 1 (05-2014)
Mode
Bright
ness
Contr
ast
Default
Mode
IMAGE
Mode
Brightness Contrast
Presentation
Mode
50
50
Video Mode
50
50
Bright Mode
50
50
Bright Mode
50
50
Real Mode
50
50
Real Mode
50
50
50
Video
Mode
NTSC
Presentation
Mode
50
50
Video Mode
50
50
Dicom Mode
50
50
Dicom Mode
50
Presentation
Mode
50
50
Presentation
Mode
50
50
Video Mode
50
50
Video Mode
50
50
Bright Mode
50
50
Bright Mode
50
50
Real Mode
50
50
Real Mode
50
50
Dicom Mode
50
50
Dicom Mode
50
50
Presentation
Mode
50
50
Presentation
Mode
50
50
50
Video
Mode
NTSC
Component/
Video
(720p,576p/I,
1080p/i…)
Video Mode
50
50
Bright Mode
50
50
Video Mode
50
Bright Mode
50
Real Mode
50
50
50
Real Mode
50
50
Dicom Mode
50
Presentation
Mode
50
50
Dicom Mode
50
50
50
Presentation
Mode
50
Video Mode
50
50
50
Video Mode
50
50
Bright Mode
50
50
Bright Mode
50
50
Real Mode
50
50
Real Mode
50
50
Dicom Mode
50
50
Dicom Mode
50
50
Video
Mode
Presentation
Mode
HDMI/DVI
(SD/HD)
6-20
Corporate offices
Worldwide offices
USA – Cypress
ph: 714-236-8610
Australia
ph: +61 (0) 7 3624 4888
Canada – Kitchener
ph: 519-744-8005
Brazil
ph: +55 (11) 2548 4753
Consultant offices
China (Beijing)
ph: +86 10 6561 0240
Italy
ph: +39 (0) 2 9902 1161
China (Shanghai)
ph: +86 21 6278 7708
Eastern Europe and
Russian Federation
ph: +36 (0) 1 47 48 100
France
ph: +33 (0) 1 41 21 44 04
Germany
ph: +49 2161 664540
India
ph: +91 (080) 6708 9999
Singapore
ph: +65 6877-8737
Japan (Tokyo)
ph: 81 3 3599 7481
Spain
ph: + 34 91 633 9990
Korea (Seoul)
ph: +82 2 702 1601
United Arab Emirates
ph: +971 4 3206688
Republic of South Africa
ph: +27 (0)11 510 0094
United Kingdom
ph: +44 (0) 118 977 8000
For the most current technical documentation, please visit www.christiedigital.com