AudioCodes MEDIAPACK VERSION 6.2 Installation manual

MediaPackTM Series Analog VoIP Gateways MP‐11x & MP‐124 Installation Manual
Version 6.2
February 2011 Document # LTRT‐59813 Installation Manual
Contents
Table of Contents
1 Introduction......................................................................................................... 9 2 Installing the Device ......................................................................................... 11 2.1 Installing MP-11x ....................................................................................................11 2.1.1 Physical Description ................................................................................................ 11 2.1.1.1 MP-11x Front Panel ................................................................................. 11 2.1.1.2 MP-11x Rear Panel ................................................................................. 12 2.1.2 Unpacking and Checking Package Contents ......................................................... 12 2.1.3 Mounting MP-11x .................................................................................................... 13 2.1.3.1 Desktop Mounting .................................................................................... 14 2.1.3.2 Wall Mounting .......................................................................................... 14 2.1.3.3 19-inch Rack Mounting ............................................................................ 14 2.1.4 Cabling MP-11x....................................................................................................... 15 2.1.4.1 Connecting MP-11x to the Network ......................................................... 16 2.1.4.2 Connecting MP-11x to FXS/FXO Devices ............................................... 16 2.1.4.3 Cabling the FXS Lifeline .......................................................................... 17 2.1.4.4 Connecting MP-11x RS-232 Port to a PC ............................................... 19 2.1.4.5 Connecting MP-11x to Power .................................................................. 20 2.2 Installing MP-124 ....................................................................................................21 2.2.1 Physical Description ................................................................................................ 21 2.2.1.1 MP-124 Front Panel ................................................................................ 21 2.2.1.2 MP-124 Rear Panel ................................................................................. 22 2.2.2 Unpacking and Checking Package Contents ......................................................... 23 2.2.3 Mounting MP-124 .................................................................................................... 23 2.2.3.1 Desktop Mounting .................................................................................... 23 2.2.3.2 19-inch Rack Mounting ............................................................................ 24 2.2.4 Cabling MP-124 ...................................................................................................... 25 2.2.4.1 Power Surge Protection and Grounding MP-124 .................................... 26 2.2.4.2 Connecting MP-124 to the Ethernet Network .......................................... 28 2.2.4.3 Connecting MP-124 to FXS Interfaces .................................................... 29 2.2.4.4 Connecting MP-124 RS-232 Port to a PC ............................................... 31 2.2.4.5 Connecting MP-124 to Power.................................................................. 32 3 Configuring the Device .................................................................................... 35 3.1 Assigning an IP Address ........................................................................................35 3.1.1 Assigning an IP Address Using HTTP .................................................................... 36 3.1.2 Assigning an IP Address Using BootP .................................................................... 37 3.1.3 Assigning an IP Address Using Voice Menu Guidance .......................................... 38 3.1.4 Assigning an IP Address Using CLI ........................................................................ 41 3.2 Configuring Basic SIP Parameters .........................................................................42 3.2.1 Enabling Channels and Configuring Call Routing (Example) ................................. 43 3.3 Saving Configuration and Resetting the Device .....................................................45 3.4 Changing Login User Name and Password ...........................................................46 3.5 Backing Up and Restoring Configuration ...............................................................47 3.6 Restoring Factory Defaults .....................................................................................48 3.7 Upgrading the Device .............................................................................................49 3.7.1 Upgrading Firmware ............................................................................................... 49 3.7.2 Loading ini and Auxiliary Files ................................................................................ 53 Version 6.2
3
February 2011
MediaPack Series
4 Monitoring the Device ...................................................................................... 55 4.1 Front-Panel LEDs ...................................................................................................55 4.2 Web Interface .........................................................................................................56 4.2.1 Viewing Alarms ....................................................................................................... 56 4.2.2 Viewing Channel Status .......................................................................................... 57 Installation Manual
4
Document #: LTRT-59813
Installation Manual
Contents
List of Figures
Figure 1-1: Required Steps to Install the Device ..................................................................................... 9 Figure 2-1: MP-11x (e.g., MP-118) Front Panel .................................................................................... 11 Figure 2-2: MP-11x (e.g., MP-118) Rear Panel ..................................................................................... 12 Figure 2-3: View of MP-11x Underside .................................................................................................. 13 Figure 2-4: 19-inch Rack Shelf for MP-11x ........................................................................................... 14 Figure 2-5: MP-11x Rack Mount ............................................................................................................ 15 Figure 2-6: RJ-45 Connector Pinouts .................................................................................................... 16 Figure 2-7: RJ-11 Phone Connector Pinouts ......................................................................................... 17 Figure 2-8: RJ-11 Lifeline Splitter Connector Pinouts ........................................................................... 17 Figure 2-9: Lifeline Cabling (Using Splitter Cable) for FXS-Only Devices............................................. 18 Figure 2-10: Lifeline Cabling for FXS and FXO Devices ....................................................................... 18 Figure 2-11: PS/2 to DB-9 Adaptor Connector Pinouts ......................................................................... 19 Figure 2-12: PS/2 Connector Pinouts .................................................................................................... 19 Figure 2-13: MP-124 Front Panel .......................................................................................................... 21 Figure 2-14: MP-124 Rear Panel - AC Power Model ............................................................................ 22 Figure 2-15: MP-124 Rear Panel - DC Power Model ............................................................................ 22 Figure 2-16: MP-124 Desktop Mounting ................................................................................................ 23 Figure 2-17: MP-124 with Brackets for Rack Installation....................................................................... 24 Figure 2-18: Grounding and Power Surge Protection ........................................................................... 27 Figure 2-19: RJ-45 Connector Pinouts .................................................................................................. 28 Figure 2-20: 50-pin Telco Connector (MP-124/FXS only) ..................................................................... 29 Figure 2-21: MP-124 in a 19-inch Rack with MDF Adaptor ................................................................... 30 Figure 2-22: MP-124 RS-232 Connector Pinouts .................................................................................. 31 Figure 2-23: Wired DC Power Terminal Block Connected to MP-124 .................................................. 33 Figure 3-1: Enter Network Password Screen ........................................................................................ 36 Figure 3-2: BootP Client Configuration Screen ..................................................................................... 38 Figure 3-3: Enabling Channels in Endpoint Phone Number Table Page .............................................. 43 Figure 3-4: Tel to IP Routing Rules ....................................................................................................... 43 Figure 3-5: Connecting Two Devices..................................................................................................... 44 Figure 3-6: Maintenance Actions Page.................................................................................................. 45 Figure 3-7: WEB User Accounts Page (for Users with 'Security Administrator' Privileges) .................. 46 Figure 3-8: Configuration File Page ....................................................................................................... 47 Figure 3-9: Start Software Upgrade Wizard Page ................................................................................. 50 Figure 3-10: Load CMP File Wizard Page ............................................................................................. 50 Figure 3-11: End Process Wizard Page ................................................................................................ 52 Figure 3-12: Load Auxiliary Files Page .................................................................................................. 53 Figure 4-1: Current Alarms in Active Alarms Page ................................................................................ 56 Figure 4-2: MP-11x Home Page ............................................................................................................ 57 Figure 4-3: MP-124 Home Page ............................................................................................................ 57 Version 6.2
5
February 2011
MediaPack Series
List of Tables
Table 2-1: MP-11x Rear Panel Component Descriptions...................................................................... 12 Table 2-2: Mounting Components on MP-11x Underside ..................................................................... 13 Table 2-3: MP-11x Rack Mount ............................................................................................................. 15 Table 2-4: Reset Button Description on MP-124 Front Panel ............................................................... 21 Table 2-5: MP-124 Rear-Panel Component Descriptions ..................................................................... 22 Table 2-6: MP-124 Rear-Panel Ethernet LEDs Description .................................................................. 22 Table 2-7: 50-pin Telco Connector Pin Allocations ............................................................................... 29 Table 3-1: Default IP Addresses ............................................................................................................ 35 Table 3-2: Configuration Parameters Available via the Voice Menu ..................................................... 40 Table 4-1: MP-11x Front-Panel LEDs Description ................................................................................ 55 Table 4-2: MP-124 Front-Panel LEDs Description ................................................................................ 55 Table 4-3: Color-Coded Channel Status Icon Description..................................................................... 57 Installation Manual
6
Document #: LTRT-59813
Installation Manual
Notices
Notice
This Installation Manual describes the hardware installation and quick configuration setup for
AudioCodes MediaPack series Voice-over-IP (VoIP) SIP media gateways.
Information contained in this document is believed to be accurate and reliable at the time of
printing. However, due to ongoing product improvements and revisions, AudioCodes cannot
guarantee accuracy of printed material after the Date Published nor can it accept responsibility
for errors or omissions.
Before consulting this document, check the corresponding Release Notes regarding feature
preconditions and/or specific support in this release. In cases where there are discrepancies
between this document and the Release Notes, the information in the Release Notes
supersedes that in this document. Updates to this document and other documents as well as
software
files
can
be
downloaded
by
registered
customers
at
http://www.audiocodes.com/downloads.
© Copyright 2011 AudioCodes Ltd. All rights reserved.
This document is subject to change without notice.
Date Published: February-06-2011
Trademarks
AudioCodes, AC, AudioCoded, Ardito, CTI2, CTI², CTI Squared, HD VoIP, HD VoIP
Sounds Better, InTouch, IPmedia, Mediant, MediaPack, NetCoder, Netrake, Nuera, Open
Solutions Network, OSN, Stretto, TrunkPack, VMAS, VoicePacketizer, VoIPerfect,
VoIPerfectHD, What’s Inside Matters, Your Gateway To VoIP and 3GX are trademarks or
registered trademarks of AudioCodes Limited. All other products or trademarks are property
of their respective owners.
WEEE EU Directive
Pursuant to the WEEE EU Directive, electronic and electrical waste must not be disposed
of with unsorted waste. Please contact your local recycling authority for disposal of this
product.
Customer Support
Customer technical support and service are provided by AudioCodes’ Distributors,
Partners, and Resellers from whom the product was purchased. For Customer support for
products purchased directly from AudioCodes, contact support@audiocodes.com.
Abbreviations and Terminology
Each abbreviation, unless widely used, is spelled out in full when first used.
Version 6.2
7
February 2011
MediaPack Series
Regulatory Information
The Regulatory Information can be viewed at http://www.audiocodes.com/downloads.
Related Documentation
Document Name
SIP Product Reference Manual
SIP Release Notes
MP-11x & MP-124 SIP User's Manual
MP-124 AC SIP Fast Track Guide
MP-124 DC SIP Fast Track Guide
MP-11x SIP Fast Track Guide
CPE Configuration Guide for IP Voice Mail
Notes: Throughout this manual and unless otherwise specified, the following terms
are used:
•
Device refers to the MediaPack series gateways.
•
MediaPack refers to MP-112, MP-114, MP-118, and MP-124.
•
MP-11x refers to MP-112, MP-114, and MP-118.
Note: The MP-11x and MP-124 devices are indoor units and therefore, must be
installed only indoors. However, the MP-124 FXS telephony cables can be
routed outdoors (MP-124 part numbers MP-124/24S/AC/OD and MP124/24S/DC/OD). Refer to Section 2.2.4.1 for surge protection means
required when such outdoor cabling is implemented.
Caution Electrical Shock
Do not open or disassemble this device. The device carries high voltage and
contact with internal components may expose you to electrical shock and
bodily harm.
Warning: The device is supplied as a sealed unit and must only be serviced by
qualified service personnel.
Warning: Disconnect the device from the mains and Telephone Network Voltage
(TNV) before servicing.
Installation Manual
8
Document #: LTRT-59813
Installation Manual
1
1. Introduction
Introduction
This manual provides you with step-by-step procedures for initial and basic setup of the
device, including hardware installation and software configuration. The flowchart below
summarizes these steps:
Figure 1-1: Required Steps to Install the Device
Note: For detailed information on how to fully configure the device, refer to the
device's User’s Manual.
Version 6.2
9
February 2011
MediaPack Series
Reader’s Notes
Installation Manual
10
Document #: LTRT-59813
Installation Manual
2
2. Installing the Device
Installing the Device
This section describes the MP-11x (refer to 'Installing the MP-11x Series' on page 11) and
MP-124 (refer to 'Installing MP-124' on page 20) hardware installation. This includes
physical description, unpacking the shipped package, and mounting and cabling
procedures.
2.1
Installing MP-11x
This subsection describes the MP-11x hardware installation.
2.1.1
Physical Description
The subsections below provide a physical description of the front and rear panels of the
MP-11x.
2.1.1.1
MP-11x Front Panel
The device's front panel provides LEDs for indicating various operating statuses. The figure
below displays the front panel of the MP-118. This is similar to the MP-114 and MP-112
models, differing only in the number of Channel Status LEDs (corresponding to the
number of channels). For a description of the device's LEDs, refer to 'Monitoring FrontPanel LEDs' on page 55.
Figure 2-1: MP-11x (e.g., MP-118) Front Panel
Version 6.2
11
February 2011
MediaPack Series
2.1.1.2
MP-11x Rear Panel
The device's rear panel provides the ports for cabling the device to the various interfaces.
The figure below displays the rear panel of the MP-118 device (as an example).
Figure 2-2: MP-11x (e.g., MP-118) Rear Panel
The following table describes the MP-11x rear panel ports:
Table 2-1: MP-11x Rear Panel Component Descriptions
Item #
Label
1
100-240~0.3A
max.
2
Ethernet
3
RS-232
Component Description
AC power supply socket.
10/100Base-TX Uplink port.
RS-232 status port (requires a DB-9 to PS/2 adaptor).
Note: MP-112 does not provide a serial port.
4
FXS and/or FXO
Provides two, four, or eight FXS/FXO ports (depending on
MediaPack model).
Note: MP-112 does not support FXO interfaces.
5
2.1.2
Reset
Reset button for resetting the device.
Unpacking and Checking Package Contents
Follow the procedure below for unpacking the carton in which MP-11x is shipped.
¾ To unpack MP-11x:
1.
Open the carton and remove the packing materials.
2.
Remove the MP-11x unit from the carton.
3.
Check that there is no equipment damage.
Installation Manual
12
Document #: LTRT-59813
Installation Manual
4.
2.1.3
2. Installing the Device
Ensure that in addition to the MP-11x unit, the package contains the following items:
•
AC power cable.
•
Small plastic bag containing four anti-slide bumpers for desktop installation.
•
Regulatory Information document.
5.
Check, retain, and process any documents.
6.
Notify AudioCodes or your local supplier of any damage or discrepancies.
Mounting MP-11x
The device can be mounted in one of the following ways:
„
Desktop mounting (refer to 'Desktop Mounting' on page 13).
„
Wall mounting (refer to 'Wall Mounting' on page 14).
„
Standard 19-inch rack mounting (refer to '19-inch Rack Mounting' on page 14).
The figure below shows the mounting components on the underside of MP-11x:
Figure 2-3: View of MP-11x Underside
Table 2-2: Mounting Components on MP-11x Underside
Item #
Functionality
1
Square slot used to attach anti-slide bumpers (for desktop mounting).
2
Oval notch used to attach MP-11x to a wall.
3
Screw opening used to attach MP-11x to a 19-inch shelf rack.
Version 6.2
13
February 2011
MediaPack Series
2.1.3.1
Desktop Mounting
Attach the four (supplied) anti-slide bumpers to the base of MP-11x and place it on a
desktop in the desired position.
2.1.3.2
Wall Mounting
Follow the procedure below for mounting MP-11x on a wall.
¾ To mount MP-11x on a wall:
1.
2.1.3.3
Drill four holes according to the following dimensions:
•
Horizontal distance between holes: 140 mm (5.51 inches)
•
Vertical distance between: 101.4 mm (4 inches)
2.
Insert a wall anchor of the appropriate size into each hole.
3.
Fasten a DIN 96 3.5 x 20 wood screws (not supplied) into each of the wall anchors.
4.
Position the four oval notches, located on the underside of MP-11x (refer to Item #2 in
'Mounting MP-11x' on page 13), over the four screws and hang MP-11x on them.
19-inch Rack Mounting
MP-11x can be installed in a standard 19-inch rack by placing it on an AudioCodes' 19-inch
rack-mounting shelf (special customer order) that must be pre-installed in a rack. The shelf
can hold up to two MP-11x devices. The rack-mounting shelf can be ordered separately
from AudioCodes. The 19-inch rack installation package contains a single shelf (shown in
the figure below), and eight shelf-to-device screws.
Figure 2-4: 19-inch Rack Shelf for MP-11x
Note: The 19-inch rack shelf is not supplied in the standard package kit, but can be
ordered separately: Bulk Pack package (MCMK00015) containing 10 rack
mounting shelves for MP-11x. For ordering and pricing, please contact your
AudioCodes' sales representative.
¾ To install MP-11x in a 19-inch rack:
1.
Attach one or two MP-11x devices to the shelf using the shelf-to-device screws
(supplied).
2.
Position the shelf in the rack and align its side holes with the rack frame holes.
Installation Manual
14
Document #: LTRT-59813
Installation Manual
3.
2. Installing the Device
Attach the shelf to the rack using four standard rack screws (not supplied).
Figure 2-5: MP-11x Rack Mount
Table 2-3: MP-11x Rack Mount
Item #
Functionality
1
Standard rack holes used to attach the shelf to the rack.
2
Eight shelf-to-device screws.
2.1.4
Cabling MP-11x
This section describes the MP-11x cabling procedures:
¾ To cable MP-11x:
„
Connecting to the Ethernet network (refer to 'Connecting MP-11x to the Network' on
page 16).
„
Connecting to FXS/FXO devices (refer to 'Connecting MP-11x to FXS/FXO Devices'
on page 16).
„
Cabling the FXS Lifeline (refer to 'Cabling MP-11x FXS Lifeline' on page 17).
„
Serial connection to a computer (refer to 'Connecting MP-11x RS-232 Port to a PC' on
page 19).
„
Connecting to the power supply (refer to 'Connecting MP-11x to Power' on page 20).
Once you have completed the above hardware installation steps and after powering-up MP11x, the Ready and Power LEDs on the front panel light up green (after a self-testing
period of about two minutes). Any malfunction in the startup procedure changes the Fail
LED to red and the Ready LED is turned off (for details on the MP-11x LEDs, refer to
'Monitoring Front-Panel LEDs' on page 55). Once you have cabled the device, you can
begin configuring the device (refer to 'Configuring the Device' on page 35).
Version 6.2
15
February 2011
MediaPack Series
2.1.4.1
Connecting MP-11x to the Network
Follow the procedure below for connecting MP-11x directly to the Ethernet network.
¾ To connect MP-11x directly to the Ethernet network:
„
Using a crossover Ethernet cable with RJ-45 connectors on either end, connect the
MP-11x Ethernet port (labeled Ethernet), directly to the network. For RJ-45 connector
pinouts, refer to the figure below:
Figure 2-6: RJ-45 Connector Pinouts
Note: When assigning an IP address to MP-11x using HTTP (refer to 'Assigning an
IP Address Using HTTP' on page 36), you may be required to disconnect the
Ethernet cable and re-cable it differently.
2.1.4.2
Connecting MP-11x to FXS/FXO Devices
Follow the procedure below for connecting MP-11x to FXO or FXS devices.
Warnings:
•
Ensure that you connect FXS ports only to analog telephones or PBX
trunk lines, and FXO ports only to CO/PBX lines; otherwise, damage to
MP-11x may occur.
•
To protect against electrical shock and fire, use a 26 AWG minimum wire
to connect FXO ports to the PSTN.
•
FXO and FXS ports are considered TNV-3
•
FXO (Foreign Exchange Office) is the interface replacing the analog
telephone and connects to a Public Switched Telephone Network (PSTN)
line from the Central Office (CO) or to a Private Branch Exchange (PBX).
The FXO is designed to receive line voltage and ringing current, supplied
from the CO or the PBX (just like an analog telephone). An FXO VoIP
device interfaces between the CO/PBX line and the Internet.
•
FXS (Foreign Exchange Station) is the interface replacing the Exchange
(i.e., the CO or the PBX) and connects to analog telephones, dial-up
modems, and fax machines. The FXS is designed to supply line voltage
and ringing current to these telephone devices. An FXS VoIP device
interfaces between the analog telephone devices and the Internet.
Notes:
Installation Manual
16
Document #: LTRT-59813
Installation Manual
2. Installing the Device
¾ To connect MP-11x to FXO or FXS devices:
„
Using an RJ-11 two-wire telephone cords (refer to figure below for connector pinouts),
connect MP-11x to the required telephone interfaces:
•
FXS: connect the MP-11x FXS ports (grouped under the label FXS) to fax
machines, modems, or telephones.
•
FXO: connect the MP-11x FXO ports (grouped under the label FXO) to telephone
exchange analog lines or PBX extensions.
Figure 2-7: RJ-11 Phone Connector Pinouts
2.1.4.3
Cabling the FXS Lifeline
The Lifeline provides a wired analog POTS phone connection to any PSTN or PBX FXS
port when there is no power or when the network connection fails. Therefore, you can use
the Lifeline phone even when MP-11x is not powered or not connected to the network.
The Lifeline feature is implemented as follows, depending on FXO/FXS support:
„
For devices providing only FXS ports: A single Lifeline connected to Port #1 using a
splitter (not supplied) is available.
„
For devices providing FXS and FXO ports: A splitter is not required - all FXS ports
are automatically connected to corresponding FXO ports (i.e., FXS Port #1 to FXO
Port #5, FXS Port #2 to FXO Port #6, and so on).
„
For devices providing only FXO ports: A Lifeline is not available.
Note: The use of the Lifeline upon network failure can be disabled using the
LifeLineType ini file parameter (described in the User's Manual).
The Lifeline’s splitter connects pins #1 and #4 to another source of an FXS port, and pins
#2 and #3 to the POTS (FXS) phone. Refer to the Lifeline splitter pinouts in the figure
below:
Figure 2-8: RJ-11 Lifeline Splitter Connector Pinouts
Version 6.2
17
February 2011
MediaPack Series
¾ To cable the MP-11x FXS Lifeline:
1.
Connect the Lifeline splitter to Port #1 on MP-11x (the Lifeline splitter is a special order
option).
2.
Connect the Lifeline phone to Port A on the Lifeline splitter.
3.
Connect an analog PSTN line to Port B on the Lifeline splitter.
Figure 2-9: Lifeline Cabling (Using Splitter Cable) for FXS-Only Devices
¾ To cable the combined MP-11x FXS/FXO Lifeline:
1.
Connect a fax machine, modem, or phone to each of the FXS ports.
2.
Connect an analog PSTN line to each of the FXO ports.
Figure 2-10: Lifeline Cabling for FXS and FXO Devices
Installation Manual
18
Document #: LTRT-59813
Installation Manual
2.1.4.4
2. Installing the Device
Connecting MP-11x RS-232 Port to a PC
Follow the procedure below to connect the MP-11x serial (RS-232) interface to a PC using
a straight-through, PS/2 to DB-9 cable adaptor.
Notes:
•
This procedure is not applicable to MP-112 as this model does not
provide an RS-232 serial interface port.
•
The PS/2 to DB-9 cable adaptor is not included in the MP-11x package.
¾ To connect MP-11x to a PC:
1.
Connect the PS/2 connector (refer to the figure below for connector pinouts) on one
end of the cable to the MP-11x RS-232 port (labeled RS-232).
2.
Connect the DB-9 connector at the other end of the cable to either the COM1 or COM2
RS-232 communication port on your PC.
Figure 2-11: PS/2 to DB-9 Adaptor Connector Pinouts
Figure 2-12: PS/2 Connector Pinouts
For information on establishing a serial communications link with MP-11x, refer to
‘Assigning an IP Address Using the CLI’ on page 41.
Version 6.2
19
February 2011
MediaPack Series
2.1.4.5
Connecting MP-11x to Power
MP-11x is powered from a standard AC electrical outlet.
Warnings:
•
The device must be connected only by professional service personnel.
•
Ensure that the device connects to an electrical socket outlet that
provides protective earthing (grounding). Prior to connecting power, refer
to the Regulatory Information document supplied with the device.
•
Use only the AC power cord supplied with the device.
¾ To connect MP-11x to the power supply:
„
Connect the MP-11x power socket to a standard electrical outlet using the supplied AC
power cord.
Installation Manual
20
Document #: LTRT-59813
Installation Manual
2.2
2. Installing the Device
Installing MP-124
This subsection describes the MP-124 hardware installation.
2.2.1
Physical Description
The subsections below provide a physical description of the MP-124 front and rear panels.
2.2.1.1
MP-124 Front Panel
The MP-124 front panel (shown in the figure below) provides LEDs for indicating various
operating statuses. In addition, the front panel provides a reset button, described in the
table below. For a description of the device's LEDs, refer to 'Monitoring Front-Panel LEDs'
on page 55.
Figure 2-13: MP-124 Front Panel
Table 2-4: Reset Button Description on MP-124 Front Panel
Type
Reset button
Version 6.2
Function
Comment
Resets MP-124.
Press the reset button with a paper clip or any other
similar pointed object, until the device resets.
Restores MP-124 to factory
default values.
Refer to 'Restoring Factory Default Settings' on
page 48.
21
February 2011
MediaPack Series
2.2.1.2
MP-124 Rear Panel
The device's rear panel (shown in the figure below) provides the ports for cabling the device
to the various interfaces.
Figure 2-14: MP-124 Rear Panel - AC Power Model
Figure 2-15: MP-124 Rear Panel - DC Power Model
The table below describes the MP-124 rear panel components.
Table 2-5: MP-124 Rear-Panel Component Descriptions
Item #
Label
Component Description
Protective earthing screw (mandatory for all installations).
Accepts a 6-32 UNC screw.
1
100-250 V~
50 - 60 Hz 2A
- or 48V 1.3A
2
3
ANALOG FXS LINES
1–24
4
RS-232
5
ETHERNET
MP-124 can be ordered with one of the following power
configurations:
ƒ
AC power: provides an AC power supply socket
ƒ
DC power: provides a DC inlet for a DC terminal block
50-pin Telco connector for 1-24 analog lines.
9-pin RS-232 port.
10/100Base-TX Ethernet RJ-45 port.
The Ethernet LEDs are located within the RJ-45 socket. The table below describes these
LEDs.
Table 2-6: MP-124 Rear-Panel Ethernet LEDs Description
Label
Type
Color
State
ETHERNET
Ethernet
Status
Green
On
Valid 10/100Base-TX Ethernet
connection.
Red
On
Malfunction.
Installation Manual
22
Function
Document #: LTRT-59813
Installation Manual
2.2.2
2. Installing the Device
Unpacking and Checking Package Contents
Follow the procedure below for unpacking the carton in which MP-124 is shipped.
¾ To unpack MP-124:
2.2.3
1.
Open the carton and remove packing materials.
2.
Remove the MP-124 unit from the carton.
3.
Check that there is no equipment damage.
4.
Ensure that in addition to the MP-124 unit, the package contains the following items:
•
AC power cable or an unwired DC terminal block with two crimping screws
(depending on ordered model).
•
Two short equal-length brackets and bracket-to-device screws for 19-inch rack
installation.
•
Regulatory Information document.
5.
Check, retain and process any documents.
6.
Notify AudioCodes or your local supplier of any damage or discrepancies.
Mounting MP-124
MP-124 can be mounted in one of the following ways:
2.2.3.1
„
Desktop mounting (refer to 'Desktop Mounting' on page 23).
„
Installed in a standard 19-inch rack (refer to '19-inch Rack Mounting' on page 24).
Desktop Mounting
For MP-124 desktop mounting, no brackets are required. Simply place MP-124 on a
desktop in the required position.
Figure 2-16: MP-124 Desktop Mounting
Version 6.2
23
February 2011
MediaPack Series
2.2.3.2
19-inch Rack Mounting
MP-124 can be installed in a standard 19-inch rack, by using two short, equal-length
brackets (supplied). MP-124 with attached brackets for rack installation is shown in the
figure below:
Figure 2-17: MP-124 with Brackets for Rack Installation
Rack Mount Safety Instructions
When installing the chassis in a rack, implement the following safety
instructions:
Installation Manual
•
Elevated Operating Ambient - If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment
may be greater than room ambient. Therefore, consideration should be
given to installing the equipment in an environment compatible with the
maximum ambient temperature (Tma) of 40°C (104°F).
•
Reduced Air Flow - Installation of the equipment in a rack should be
such that the amount of air flow required for safe operation on the
equipment is not compromised.
•
Mechanical Loading - Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven
mechanical loading.
•
Circuit Overloading - Consideration should be given to the connection
of the equipment to the supply circuit and the effect that overloading of
the circuits might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be
used when addressing this concern.
•
Reliable Earthing - Reliable earthing of rack-mounted equipment should
be maintained. Particular attention should be given to supply connections
other than direct connections to the branch circuit (e.g., use of power
strips.)
24
Document #: LTRT-59813
Installation Manual
2. Installing the Device
¾ To install MP-124 in a 19-inch rack:
2.2.4
1.
Remove the two screws located on one side of MP-124 (nearest the front panel).
2.
Insert the peg on one of the brackets into the third air vent down on the column of air
vents nearest the front panel.
3.
Swivel the bracket until the holes in the bracket align with the two empty screw holes
on MP-124.
4.
Use the supplied screws to attach the bracket to the side of MP-124.
5.
Repeat steps 1 through 4 to attach the second bracket to the other side of MP-124.
6.
Position MP-124 in the rack and line up the bracket holes with the rack frame holes.
7.
Use four standard rack screws (not supplied) to attach MP-124 to the rack.
Cabling MP-124
This section describes the MP-124 cabling procedures:
„
Grounding (earthing) MP-124 (refer to 'Grounding MP-124' on page 25).
„
Connecting to the Ethernet network (refer to 'Connecting MP-124 to the Ethernet
Network' on page 27).
„
Connecting to FXS analog lines (refer to 'Connecting MP-124 to FXS Interface' on
page 28).
„
Serial connection to a computer (refer to 'Connecting MP-124 RS-232 Port to a PC' on
page 30).
„
Connecting to the power supply (refer to 'Connecting MP-124 to Power' on page 31).
Once you have completed the above hardware installation steps and after powering-up MP124, the Ready and LAN LEDs on the front panel light up green (after a self-testing period
of about a minute). Any malfunction in the startup procedure changes the Ready LED to
red (for details on the MP-124 LEDs, refer to 'Monitoring Front-Panel LEDs' on page 55).
Once you have cabled the device, you can begin configuring the device (refer to
'Configuring the Device' on page 35).
Version 6.2
25
February 2011
MediaPack Series
2.2.4.1
Power Surge Protection and Grounding MP-124
This section discusses power surge protection and grounding of MP-124.
Warning:
•
Ensure that you connect MP-124 to an electrical socket outlet that
provides protective earthing (grounding). Prior to connecting power, refer
to the Regulatory Information provided in the User’s Manual.
For Finland: "Laite on liltettava suojamaadoituskoskettimilla varustettuun
pistorasiaan."
For Norway: "Apparatet rna tilkoples jordet stikkontakt."
For Sweden: "Apparaten skall anslutas till jordat uttag."
•
MP-124 is immune against power surge levels of up to 1 Kilovolts (KV) as
required by the following standards: IEC 61000-4-5, EN 55024, and EN
300386.
•
For installations where wires are routed outside the building, the
Telecommunication site must comply with ETS 300-253 “Earthing and
Bonding of Telecommunication Equipment in Telecommunication
Centers”.
•
Power surges above protection levels as required by EN 55024/EN
300386 may cause damage to MP-124.
•
MP-124 provides only Secondary Protection against power surges. In
deployments where the telephone lines are installed outside, you must
install Primary Protection against lightning. Only lightning protectors
recommended by AudioCodes must be used - specifically, manufactured
by Circa. Failing to install Circa primary surge protectors, failing to comply
with the grounding instructions or any other installation instructions, may
cause permanent damage to MP-124.
•
As most of the installation is the responsibility of the customer,
AudioCodes can assume responsibility for damage only if the customer
can establish that MP-124 does not comply to the standards specified
above (and MP-124 is within the hardware warranty period).
Lightning is the transient passage of electrical current between a cloud and the surface of
the earth. Part of the lightning current can be carried inside a building from electrical lines
and analog and/or digital telephone lines located outside. This direct injection of lightning
current inside a building can cause significant damage to electronic circuits and equipment.
To protect MP-124 from these power surges, MP-124 must be connected to an external
lightning protector. You must use a lightning protector of the type CIRCA 4B1FS-240
manufactured by CircaTelecom (http://www.circatelecom.com). The connection must be
made using the terminal fixture of the type CIRCA 2625QC/QC.
This fixture must be connected alongside or within the Main Distribution Frame (MDF). You
must connect the grounding connection of this electrical cabinet to the grounding bus of the
electrical circuit board, using AWG wires of at least 10mm2 and maximum length of 3
meters.
MP-124 must be connected to the power surge protector using minimum 26-AWG wire
thickness.
Installation Manual
26
Document #: LTRT-59813
Installation Manual
2. Installing the Device
MP-124 must be installed in the Telecommunication rack. MP-124 grounding screw must
be connected to the equipotential grounding bus bar located in the Telecommunication
rack, using a wire of 6mm2 surface wire. This line must be connected to the equipotential
bus bar of the electrical circuit board located in the Telecommunication room, using a
stranded cable with surface area of 25 mm2. The length of this cable must be as short as
possible; no longer than 3 meters.
The MP-124 chassis is equipped with a protective earthing screw. Ensure that you connect
this to the grounding point using a suitable wire. Fasten the cable securely using a 6-32
UNC screw.
Note: Proper grounding is crucial to ensure the effectiveness of the primary protection
devices against power surges. Therefore, both the primary protector and MP-124 must be
connected to the equipotential ground bus (in electrical switch board) that is connected
directly to the grounding of the foundation reinforcement conductor.
Before installation, loop-testing grounding measurements must be done by a certified
electrician to verify the quality of the grounding connection. The grounding impedance must
not exceed 0.5 ohm.
The figure below illustrates the connection method for grounding and lightning protector.
Figure 2-18: Grounding and Power Surge Protection
Telecommunication Room
Telephone Lines
Outside Building
Main Distribution Frame (MDF)
Equipment Rack
Tip
Stranded
Wire
10 mm 2
26 AWG
50-Pin Telco for
Telephone Lines
MP-124
Equipotential
Ground Bus Bar
Ring
Stranded Wire
6 mm 2
Primary Lightning
Protection (CIRCA)
MP-124
Equipotential Ground Bus
in Electrical Board
To Foundation
Reinforcement/Ring Conductor (Ground)
Version 6.2
27
February 2011
MediaPack Series
2.2.4.2
Connecting MP-124 to the Ethernet Network
Follow the procedure below for connecting MP-124 directly to the Ethernet network.
¾ To connect MP-124 directly to the Ethernet network:
„
Using a crossover Ethernet cable with RJ-45 connectors on either end, connect the
MP-124 Ethernet port (labeled ETHERNET), directly to the network. For RJ-45
connector pinouts, refer to the figure below:
Figure 2-19: RJ-45 Connector Pinouts
Note: When assigning an IP address to MP-124 using HTTP (refer to 'Assigning an
IP Address Using HTTP' on page 36), you may be required to disconnect the
Ethernet cable and re-cable it differently.
Installation Manual
28
Document #: LTRT-59813
Installation Manual
2.2.4.3
2. Installing the Device
Connecting MP-124 to FXS Interfaces
The MP-124 interfaces with the analog telephone interfaces by connecting to a main
distribution frame (MDF), using a 50-pin Telco cable.
MP-124 Safety Notice
To protect against electrical shock and fire, use a 26 AWG min wire to connect
analog FXS lines to the 50-pin Telco connector.
Warning: To reduce noise interference, use a twisted pair Octopus cable that is
terminated on a metal-hooded 50-pin Telco connector.
¾ To connect MP-124 to the FXS telephone interface:
1.
Wire the 50-pin Telco connectors according to the pinouts in the table below:
Table 2-7: 50-pin Telco Connector Pin Allocations
Phone Channel
Connector Pins
Phone Channel
Connector Pins
1
1/26
13
13/38
2
2/27
14
14/39
3
3/28
15
15/40
4
4/29
16
16/41
5
5/30
17
17/42
6
6/31
18
18/43
7
7/32
19
19/44
8
8/33
20
20/45
9
9/34
21
21/46
10
10/35
22
22/47
11
11/36
23
23/48
12
12/37
24
24/49
Figure 2-20: 50-pin Telco Connector (MP-124/FXS only)
2.
Version 6.2
Attach each pair of wires from a 25-pair Octopus cable (not supplied) to its
corresponding socket on the MDF adaptor block’s rear panel.
29
February 2011
MediaPack Series
3.
Connect the wire-pairs at the other end of the cable to a male 50-pin Telco connector
(not supplied).
4.
Insert and fasten the male connector to the female 50-pin Telco connector on the
MP-124 rear panel (labeled Analog FXS Lines 1-24).
5.
Connect the telephone lines from the MDF adaptor block to a fax machine, modem, or
telephones by inserting each RJ-11 connector on the 2-wire line cords of the POTS
phones into the RJ-11 sockets on the front of an MDF adaptor block, as shown in the
figure below.
Figure 2-21: MP-124 in a 19-inch Rack with MDF Adaptor
Installation Manual
30
Document #: LTRT-59813
Installation Manual
2.2.4.4
2. Installing the Device
Connecting MP-124 RS-232 Port to a PC
Follow the procedure below to connect the MP-124 serial (RS-232) interface to a PC using
a standard, straight-through cable with DB-9 connectors on either end.
¾ To connect MP-124 to a PC:
1.
Connect the DB-9 connector (refer to the figure below for connector pinouts) on one
end of the cable to the MP-124 RS-232 port (labeled RS-232).
2.
Connect the DB-9 connector (refer to the figure below for connector pinouts) at the
other end of the cable to either the COM1 or COM2 RS-232 communication port on
your PC.
Figure 2-22: MP-124 RS-232 Connector Pinouts
For information on establishing a serial communications link with MP-124, refer to
‘Assigning an IP Address Using the CLI’ on page 41.
Version 6.2
31
February 2011
MediaPack Series
2.2.4.5
Connecting MP-124 to Power
MP-124 can be powered either from a standard AC electrical outlet or a 48-VDC power
supply. The power configuration depends on the ordered MP-124 model.
2.2.4.5.1 AC Power Supply
This section describes cabling of the MP-124 model for AC power.
Warnings:
•
The device must be connected only by professional service personnel.
•
Ensure that the device connects to an electrical socket outlet that
provides protective earthing (grounding). Prior to connecting power, refer
to the Regulatory Information document supplied with the device.
•
Use only the AC power cord supplied with the device.
¾ To connect MP-124 to the AC power supply:
„
Connect the MP-124 AC power socket (located on the rear panel) to a standard
electrical wall outlet, using the supplied AC power cord.
Installation Manual
32
Document #: LTRT-59813
Installation Manual
2. Installing the Device
2.2.4.5.2 DC Power Supply
This section describes cabling of the MP-124 model for 48-VDC power supply.
MP-124 DC Safety Notice
When connecting MP-124 to a DC power supply, ensure that you adhere to
the following safety guidelines:
•
Connect the device to a safety extra-low voltage (SELV) source that is
sufficiently isolated from the mains.
•
Connect the device permanently to earth (ground) using the earthing
(grounding) stud located on its’ rear panel (refer to 'Grounding MP-124'
on page 25).
¾ To connect MP-124 to a DC power supply:
1.
Insert two 18 AWG wires into the supplied DC terminal block (ensure correct polarity),
and then fasten the two screws located directly above each wire block.
2.
Insert the DC terminal block into the DC inlet on the MP-124 rear panel, and then
secure it to the device by fastening the two adaptor-to-panel screws located on the
terminal block.
Figure 2-23: Wired DC Power Terminal Block Connected to MP-124
Legend:
3.
Version 6.2
1.
Two integral screws for wire connection to the DC terminal block.
2.
Two integral screws for connecting the DC terminal block to the MP-124 DC inlet.
3.
Two 18 AWG wires (positive and negative polarity).
Connect the other end of the DC cable to a 48-VDC power supply.
33
February 2011
MediaPack Series
Reader’s Notes
Installation Manual
34
Document #: LTRT-59813
Installation Manual
3
3. Configuring the Device
Configuring the Device
This section describes initial, basic setup configuration for the device, using the device's
embedded Web server (Web interface).
Notes:
3.1
•
The device is supplied with application software (cmp file) already
residing on its flash memory. This software is set to factory defaults.
•
If necessary, you can restore the device to factory defaults (refer to
'Restoring Factory Default Settings' on page 48).
Assigning an IP Address
This section describes how to change the device's default IP address so that it corresponds
with your network environment. The table below lists the device's default IP address.
Table 3-1: Default IP Addresses
Parameter
IP Address
Default Value
ƒ
FXS and FXS / FXO devices: 10.1.10.10
ƒ
FXO device: 10.1.10.11
Note: FXO interfaces are applicable only to MP-11x series
devices.
Subnet Mask
255.255.0.0
Default Gateway IP Address
0.0.0.0
To assign an IP address to the device, use one of the following methods:
„
Device's HTTP-based embedded Web server `accessed using a Web browser (refer to
'Assigning an IP Address Using HTTP' on page 36).
„
BootP (refer to 'Assigning an IP Address Using BootP' on page 37).
„
Voice Menu using a standard touch-tone telephone connected to one of the FXS
analog ports (refer to ‘Assigning an IP Address Using the Voice Menu Guidance’ on
page 38).
„
Embedded Command Line Interface (CLI), accessed using RS-232 or Telnet (refer to
'Assigning an IP Address Using CLI' on page 40).
„
Dynamic Host Control Protocol (DHCP) - refer to the User's Manual.
Tip:
Version 6.2
If at a later stage after re-defining the IP address, your IP address is unknown
(e.g., forgotten), use the BootP/TFTP utility to access the device (refer to the
Product Reference Manual).
35
February 2011
MediaPack Series
3.1.1
Assigning an IP Address Using HTTP
You can assign an IP address to the device, using the device's Web interface.
¾ To assign an IP address using HTTP:
1.
Disconnect the device from the network and reconnect it to a PC using one of the
following methods:
•
Using a hub or switch between a PC and the device: Connect the network
interface on your PC to a port on a network hub / switch, using a standard
Ethernet cable. Connect the device to another port on the same network hub /
switch, using another standard Ethernet cable.
•
Direct connection between a PC and the device: Connect the network
interface on your PC directly to the device, using an Ethernet crossover cable.
2.
Change your PC’s IP address and subnet mask to correspond with the device's factory
default IP address and subnet mask (for default IP addresses, refer to Assigning an IP
Address on page 35).
3.
Access the device's Web interface:
a.
Open a standard Web browser application and in the Uniform Resource Locator
(URL) field, enter the device's default IP address (e.g., http://10.1.10.10); the Web
interface's 'Enter Network Password' dialog box appears, as shown in the figure
below:
Figure 3-1: Enter Network Password Screen
b.
Enter the device's default login, case-sensitive user name ('Admin') and password
('Admin'), and then click OK; the Web interface is accessed, displaying the Web
interface's 'Home' page.
Note: To prevent unauthorized access to the device, it's recommended that after
you initially access the Web interface to change the default login user name
and password (refer to Changing the Login User Name and Password on
page 45).
Installation Manual
36
Document #: LTRT-59813
Installation Manual
4.
3.1.2
3. Configuring the Device
Change the device's IP address, by performing the following:
a.
Open the ‘Multiple Interface Table’ page (Configuration tab > VoIP menu >
Network submenu > IP Settings).
b.
Define the device's IP address, subnet mask, and default Gateway IP address (for
“OAMP + Media + Control” application type) so that they correspond to your
network IP scheme.
c.
Click Apply.
d.
Save your settings to the flash memory and reset the device (refer to 'Saving and
Resetting the Device' on page 44).
5.
Disconnect your PC from the device or from the hub/switch (depending on the
connection method used in Step 1).
6.
Reconnect the device and PC (if necessary) to the network.
7.
Restore your PC’s IP address and subnet mask to their original settings. If necessary,
restart your PC and re-access the device via the Web interface with its newly assigned
IP address.
Assigning an IP Address Using BootP
You can assign an IP address to the device, using the supplied AudioCodes' BootP/TFTP
Server application.
Notes:
•
BootP procedure can also be performed using any standard compatible
BootP server.
•
For a detailed description of BootP, refer to the Product Reference
Manual.
¾ To assign an IP address using BootP:
1.
Start the BootP application.
2.
From the Edit menu, choose Preferences, and then in the 'Preferences' dialog box,
set the 'Timeout' field to 50.
3.
From the Services menu, choose Clients; the 'Client Configuration' dialog box
appears.
4.
Click the Add New Client
5.
In the ‘Client MAC’ field, enter the device's MAC address. The MAC address is printed
on the label located on the underside of the device. Ensure that the check box to the
right of the field is selected - this enables the client in the BootP tool (if the client is
disabled, no replies are sent to BootP requests).
6.
In the ‘IP’ field, enter the IP address (in dotted-decimal notation) that you want to
assign to the device.
7.
In the ‘Subnet’ field, enter the subnet mask (in dotted-decimal notation) that you want
to assign to the device. Ensure that the subnet mask is valid, otherwise, the device
may not function.
Version 6.2
icon; a client with blank parameters is displayed.
37
February 2011
MediaPack Series
8.
In the ‘Gateway’ field, enter the IP address of the default gateway (if any).
9.
Click Apply to save the new client.
10. Click OK; the ‘Client Configuration’ screen closes.
11. Physically reset the device using the hardware reset button (or power down and then
power up the device). This causes the device to use BootP; the device changes its
network parameters to the values provided by BootP.
Figure 3-2: BootP Client Configuration Screen
3.1.3
Assigning an IP Address Using Voice Menu Guidance
Initial configuration of the device can be performed using a standard touch-tone telephone
connected to one of the FXS ports. The voice menu can also be used to query and modify
basic configuration parameters.
Note: The Voice menu is automatically disabled after the administrator password is
set to a value other than the default ("Admin").
¾ To assign an IP address using the voice menu guidance:
1.
Connect a telephone to one of the FXS ports.
2.
Lift the handset and dial ***12345 (three stars followed by the digits 1, 2, 3, 4, and 5).
3.
Wait for the 'configuration menu' voice prompt to be played.
4.
To change the IP address:
a.
Press 1 followed by the pound key (#); The current IP address of the device is
played.
b.
Press the # key.
Installation Manual
38
Document #: LTRT-59813
Installation Manual
5.
6.
3. Configuring the Device
c.
Dial the new IP address. Use the star (*) key instead of periods (.), e.g.,
192*168*0*4, and then press # to finish.
d.
Review the new IP address, and then press 1 to save.
To change the subnet mask:
a.
Press 2 followed by the # key; The current subnet mask of the device is played.
b.
Press the # key.
c.
Dial the new subnet mask (e.g., 255*255*0*0), and then press # to finish.
d.
Review the new subnet mask, and then press 1 to save.
To change the default Gateway IP address:
a.
Press 3 followed by the # key; The current default Gateway address is played.
b.
Press the # key.
c.
Dial the new default Gateway address (e.g., 192*168*0*1), and then press # to
finish.
d.
Review the new default Gateway address, and then press 1 to save.
7.
Hang up the handset.
8.
Access the device's Web interface with the new IP address you assigned.
Alternatively, initial configuration may be performed using an HTTP server, as discussed in
the Product Reference Manual ('Automatic Update Facility'). The Voice Menu may be used
to specify the configuration URL.
¾ To set a configuration URL:
1.
Obtain the IP address of the configuration HTTP server (e.g., 36.44.0.6).
2.
Connect a telephone to one of the FXS ports.
3.
Lift the handset and dial ***12345 (three stars followed by the digits 1, 2, 3, 4, and 5).
4.
Wait for the 'configuration menu' voice prompt to be played.
5.
Dial 31 followed by the # key; the current IP address is played.
6.
To change the IP address, perform the following:
7.
#
a.
Press the # key.
b.
Dial the configuration server's IP address. Use the star (*) key instead of dots ("."),
e.g., 36*44*0*6, and then press # to finish.
c.
Review the configuration server's IP address, and then press 1 to save.
Dial 32 followed by the # key, and then perform the following to change the
configuration file name pattern:
a.
Press the # key.
b.
Select one of the patterns listed in the table below (aa.bb.cc.dd denotes the IP
address of the configuration server):
Configuration File Name Pattern
Description
1
http://aa.bb.cc.dd/config.ini
Standard config.ini.
2
https://aa.bb.cc.dd/config.ini
Secure HTTP.
3
http://aa.bb.cc.dd/audiocodes/<MAC>.ini
The device's MAC address is appended to the file
name (e.g.,
http://36.44.0.6/audiocodes/00908f012300.ini).
Version 6.2
39
February 2011
MediaPack Series
#
Configuration File Name Pattern
Description
4
http://aa.bb.cc.dd:8080/config.ini
HTTP on port 8080.
5
http://aa.bb.cc.dd:1400/config.ini
HTTP on port 1400.
6
http://aa.bb.cc.dd/cgibin/acconfig.cgi?mac=<MAC>&ip=<IP>
Generating configuration per IP/MAC address
dynamically, using a CGI script. See perl example
below.
c.
8.
Press the selected pattern code, and then press # to finish.
Press 1 to save, and then hang up the handset. The device retrieves the configuration
from the HTTP server.
The following is an example perl CGI script, suitable for most Apache-based HTTP servers
for generating configuration dynamically per pattern #6 above. Copy this script to
/var/www/cgi-bin/acconfig.cgi on your Apache server and edit it as required:
#!/usr/bin/perl
use CGI;
$query = new CGI;
$mac = $query->param('mac');
$ip = $query->param('ip');
print "Content-type: text/plain\n\n";
print "; INI file generator CGI\n";
print "; Request for MAC=$mac IP=$ip\n\n";
print <<"EOF";
SyslogServerIP = 36.44.0.15
EnableSyslog = 1
SSHServerEnable = 1
EOF
The table below lists the configuration parameters that can be queried or modified using the
voice menu:
Table 3-2: Configuration Parameters Available via the Voice Menu
Item Number at
Menu Prompt
Description
1
IP address.
2
Subnet mask.
3
Default Gateway IP address.
4
Primary DNS server IP address.
7
DHCP enable / disable.
31
Configuration server IP address.
32
Configuration file name pattern.
99
Voice menu password (initially 12345).
Note: The voice menu password can also be changed using the Web interface
or ini file parameter VoiceMenuPassword (refer to the User's Manual).
Installation Manual
40
Document #: LTRT-59813
Installation Manual
3.1.4
3. Configuring the Device
Assigning an IP Address Using CLI
You can assign an IP address to the device, using command-line interface (CLI).
Note: The CLI method for assigning an IP address is not applicable to MP-112 as
this model does not provide RS-232 serial interface.
¾ To assign an IP address using CLI:
1.
2.
Connect the device's RS-232 port to either COM1 or COM2 communication port on
your PC:
•
For MP-11x, refer to “Connecting the MP-11x RS-232 Port to Your PC” on page
19
•
For MP-124, refer to “Connecting the MP-124 RS-232 Port to Your PC” on page
30
Use a serial communication software (e.g., HyperTerminalTM) to establish a serial
communication link with the device, using the following communications port settings:
•
Baud Rate: 9,600 bps for MP-11x; 115,200 bps for MP-124
•
Data Bits: 8
•
Parity: None
•
Stop Bits: 1
•
Flow Control: None
The CLI prompt appears.
3.
At the prompt, type the following command, and then press <Enter> to access the
CONFiguration folder:
conf
4.
To view the current network parameters, at the prompt, type the following command,
and then press <Enter>:
GCP IP
5.
Change the network settings by typing the following command:
SCP IP [ip_address] [subnet_mask] [default_gateway]
For example,
SCP IP 10.13.77.7 255.255.0.0 10.13.0.1
The new settings take effect on-the-fly and connectivity to the device is active at the
new IP address.
Note: For the SCP IP command, you must enter all three network parameters (each
separated by a space).
6.
To save the configuration, at the prompt, type the following command, and then press
<Enter>:
SAR
7.
Version 6.2
The device restarts with the new network settings.
41
February 2011
MediaPack Series
3.2
Configuring Basic SIP Parameters
Once you have completed the previous sections, you are ready to start configuring the
device using the Web interface. For information on how to fully configure the device, refer to
the device's User’s Manuals.
Tip:
Once the device is configured, backup your settings by saving the
configuration (ini) file to your PC. This saved file can later be used, if
necessary, to restore configuration settings (refer to 'Backing Up and
Restoring Configuration' on page 47).
¾ To configure basic SIP parameters:
1.
Access the Web interface.
2.
Select the voice coders used by the device that best suits your VoIP network, in the
'Coders Table' page (Configuration tab > VoIP menu > Coders And Profiles
submenu > Coders).
3.
When operating with a Proxy server, perform the following (otherwise, skip to Step 4):
a.
b.
In the 'Proxy & Registration' page (Configuration tab > VoIP menu > SIP
Definitions submenu > Proxy & Registration):
♦
Set the ‘Use Default Proxy’ field to "Yes".
♦
(Optional) In the ‘Proxy Name’ field, enter the Proxy's name. The Proxy
name replaces the Proxy IP address in all SIP messages. This means that
messages are still sent to the physical Proxy IP address, but the SIP URI
contains the Proxy name instead.
♦
To enable the device to register to a Proxy/Registrar server (at power up and
every user-defined interval - ‘Registration Time’ parameter), set the ‘Enable
Registration’ parameter to "Enable".
In the 'Proxy Sets Table' page (Configuration tab > VoIP menu > Control
Network submenu > Proxy Sets Table), define the IP address(s) of the Proxy
server(s). When no Proxy is used, the internal routing table is used to route the
calls.
4.
Enable the device's endpoints in the 'Endpoint Phone Number Table' page
(Configuration tab > VoIP menu > GW and IP to IP submenu > Hunt Group
submenu > Endpoint Phone Number).
5.
If a Proxy server is not implemented, map outgoing calls to IP addresses in the
‘Outbound IP Routing Table’ page (Configuration tab > VoIP menu > GW and IP to
IP submenu > Routing submenu > Tel to IP Routing).
6.
Save your settings to the flash memory and reset the device (refer to 'Saving and
Resetting the Device' on page 44).
Installation Manual
42
Document #: LTRT-59813
Installation Manual
3.2.1
3. Configuring the Device
Enabling Channels and Configuring Call Routing (Example)
This section provides an example for enabling the device's channels and for configuring Tel
(PSTN)-to-IP call routing. This includes assigning the channels a telephone number and
then routing calls (e.g., of dialed numbers with prefix 10) from these channels to a specific
IP destination (e.g., IP address 10.33.24.14).
¾ To enable channels and configure call routing:
1.
Assign telephone numbers to endpoints, by performing the following:
a.
Open the 'Endpoint Phone Number Table' page (Configuration tab > VoIP menu
> GW and IP to IP submenu > Hunt Group submenu > Endpoint Phone
Number).
Figure 3-3: Enabling Channels in Endpoint Phone Number Table Page
2.
b.
In the 'Channel(s)' column, enter 1-8 (i.e., channels 1 through 8), and then in the
'Phone Number' column, enter the phone number (e.g., 101) for the first channel.
Phone numbers 102, 103, 104 and so on are sequentially assigned to subsequent
channels (i.e., 2 through 8).
c.
Click Submit.
Configure routing of telephone calls to an IP destination (i.e., IP address):
a.
Open the ‘Tel to IP Routing Table’ page (Configuration tab > VoIP menu > GW
and IP to IP submenu > Routing submenu > Tel to IP Routing).
Figure 3-4: Tel to IP Routing Rules
b.
In the 'Dest. Phone Prefix' column, enter "10" (i.e., prefix of dialed number).
c.
In the 'Source Phone Prefix' column, enter the prefix of the channel's telephone
number as defined in Step 1.
d.
In the 'Dest. IP Address' column, enter 10.33.24.14 (i.e., calls are sent to this IP
address).
e.
Click Submit.
Therefore, any call whose dialed number prefix matches the value in the 'Dest. Phone
Prefix’ column (i.e., 10) and whose source phone number prefix matches the value in
the ‘Source Phone Prefix‘ column is sent to the IP address defined in the ‘Dest. IP
Address’ column.
Version 6.2
43
February 2011
MediaPack Series
The figure below shows an example of a configuration setup of two communicating FXS
devices. Phones ‘101’ and '102' are connected to the first two channels of device with IP
address 10.33.24.18; phone ‘120’ is connected to the first channel of device 10.33.24.14.
The configuration in the 'Endpoint Phone Number Table' and ‘Tel to IP Routing Table’
pages (refer to the figure below) enables calls to be made between these two devices as
well as between phones connected to the same device.
To make a call between the two devices, off-hook phone ‘101’, and at the dial tone, dial
'120'. To make a call between the two phones that are connected to device 10.33.24.18,
off-hook phone '101' and then at the dial tone, dial '102' (or vice versa).
Notes:
•
The prefixes entered in the ‘Tel to IP Routing Table’ must differentiate the
devices from each other to ensure correct routing. In the example, using
the first digit (i.e., 1) doesn’t differentiate the devices, therefore, two digits
of the phone number are used.
•
To enable phones connected to the same device to communicate with
each other, define in the ‘Tel to IP Routing Table’ the IP address and
corresponding phone numbers of the device itself.
Figure 3-5: Connecting Two Devices
Installation Manual
44
Document #: LTRT-59813
Installation Manual
3.3
3. Configuring the Device
Saving Configuration and Resetting the Device
To apply configuration changes to the device's volatile memory (RAM), click the Submit
button located on the page in which you are configuring. Modifications to parameters
with on-the-fly capabilities are immediately applied to the device; other parameters are
applied only after a device reset. However, parameters saved to the volatile memory revert
to their previous settings after a hardware or software reset (or if the device is powered
down). Therefore, to ensure that all parameter changes (whether on-the-fly or not) are
retained, you need to save ('burn') them to the device's non-volatile memory (i.e., flash).
You can also "gracefully lock" the device so that no new calls are allowed and existing calls
are terminated only after a user-defined period. This is useful when, for example, you are
uploading new software files to the device and you don't want to disrupt existing traffic.
Note: Parameters preceded by the lightning
and require a device reset.
sign are not changeable on-the-fly
¾ To save parameters to flash memory and reset the device:
1.
On the toolbar, click Device Actions, and then from the drop-down list, choose Reset;
the 'Maintenance Actions' page appears.
Figure 3-6: Maintenance Actions Page
2.
Under the 'Reset Configuration' group, ensure that 'Yes' is selected in the 'Burn to
FLASH' drop-down list.
3.
(Optional) To gracefully lock the device, click the LOCK button, from the 'Graceful
Option' drop-down list select 'Yes', and then define the time (in seconds) after which
the device locks.
4.
Click the Reset button.
Version 6.2
45
February 2011
MediaPack Series
3.4
Changing Login User Name and Password
To prevent unauthorized access to the Web interface, two Web user accounts (login
accounts) are available (primary and secondary) with assigned user name and password.
For detailed information on the Web user accounts, refer to the device's User’s Manual.
Tip:
If you do not know your user name and password, you can use AudioCodes
BootP/TFTP utility to access the device, by re-flash the load and resetting the
password (refer to the Product Reference Manual).
¾ To change the login user name and password:
1.
Open the 'WEB User Accounts' page (Configuration tab > System menu > Web User
Accounts).
Figure 3-7: WEB User Accounts Page (for Users with 'Security Administrator' Privileges)
2.
3.
To change the user name, perform the following:
a.
In the 'User Name' field, enter the new user name (maximum of 19 case-sensitive
characters).
b.
Click Change User Name; the new user name is applied and the 'Enter Network
Password' screen appears.
c.
In the 'Enter Network Password' screen, enter the new user name.
To change the password, perform the following:
a.
In the 'Current Password' field, enter the current password (maximum of 19 casesensitive characters).
b.
In the 'New Password' and 'Confirm New Password' fields, enter the new
password.
c.
Click Change Password; the new password is applied and the 'Enter Network
Password' screen appears. In the 'Enter Network Password' screen, enter the
new password.
Installation Manual
46
Document #: LTRT-59813
Installation Manual
3.5
3. Configuring the Device
Backing Up and Restoring Configuration
You can save a copy/backup of the device's current configuration settings as an ini file to a
folder on your PC. The saved ini file includes only parameters that were modified and
parameters with other than default values. If the device has "lost" its configuration, you can
restore the device's configuration by loading the previously saved ini file or by loading a
newly created ini file.
Note: When loading an ini file using the method described below, parameters not
included in the ini file are reset to default settings.
¾ To save and restore the ini file:
1.
Open the 'Configuration File' page (Maintenance tab > Software Update menu >
Configuration File).
Figure 3-8: Configuration File Page
2.
To save the ini file to a folder on your PC, perform the following:
a.
Click the Save INI File button; the 'File Download' dialog box appears.
b.
Click the Save button, navigate to the folder in which you want to save the ini file
on your PC, and then click Save; the device copies the ini file to the selected
folder.
¾ To load an ini file:
1.
Click the Browse button, navigate to the folder in which the ini file is located, select the
file, and then click Open; the name and path of the file appear in the field beside the
Browse button.
2.
Click the Load INI File button, and then at the prompt, click OK; the device uploads
the ini file and then resets (from the cmp version stored on the flash memory). Once
complete, you are requested to log in to the Web interface once again.
Version 6.2
47
February 2011
MediaPack Series
3.6
Restoring Factory Defaults
You can use the device's hardware Reset button to restore all the device's configuration
settings to factory defaults, including the device's IP address and Web interface's login user
name and password.
Notes:
•
The device resets to the software version (cmp file) saved on its flash
memory.
•
For additional methods to restore default settings, refer to the User's
Manual.
¾ To restore MP-124 to factory default settings:
1.
Disconnect the Ethernet cable from the device.
2.
With a paper clip or any other similar pointed object, press and hold down the Reset
button (located on the front panel) for at least 12 seconds (but no more than 25
seconds); the device restores to factory default settings.
¾ To restore MP-11x to factory default settings:
1.
Disconnect the Ethernet cable from the device.
2.
With a paper clip or any other similar pointed object, press and hold down the Reset
button (located on the rear panel) for about six seconds; the Fail LED turns red and
the device restores to factory default settings.
3.
When the Fail LED turns off, reconnect the Ethernet cable to the device.
Installation Manual
48
Document #: LTRT-59813
Installation Manual
3.7
3. Configuring the Device
Upgrading the Device
You can upgrade the device with the following files:
„
Firmware (cmp) file using the Web interface's Software Update Wizard (refer to
‘Upgrading Firmware’ on page 49).
„
Auxiliary and ini files using the Web interface's 'Load Auxiliary Files' page (refer to
'Upgrading the ini and Auxiliary Files' on page 53).
Note: When upgrading the firmware (cmp), you can also use the Software Update
Wizard to load the ini and auxiliary files.
3.7.1
Upgrading Firmware
The Software Upgrade Wizard allows you to easily upgrade the device's firmware (cmp
file). The wizard can also be used to load an ini file and/or auxiliary files (e.g., Call Progress
Tones). however, this can only be done if a cmp file is also loaded to the device at the
same time. For the ini and each auxiliary file type, you can choose to load a new file, or not
load a file but use the existing file (i.e., maintain existing configuration) running on the
device.
Warnings:
•
Before upgrading the device, it is recommended that you save a copy of
the device's configuration settings (i.e., ini file) to your PC. If an upgrade
failure occurs, you can then restore your configuration settings by
uploading the backup file to the device. For backing up and restoring
configuration, refer to 'Backing Up and Restoring Configuration' on page
47.
•
The Software Upgrade Wizard requires the device to be reset at the end
of the process, which may disrupt traffic. To avoid this, disable all traffic
on the device before initiating the wizard, by performing a graceful lock
(refer to 'Saving Configuration and Resetting the Device' on page 44).
•
Before you can load an ini or auxiliary file, you must first load a cmp file.
•
When you activate the wizard, the rest of the Web interface is
unavailable. After the files are successfully loaded, access to the full Web
interface is restored.
•
You can schedule automatic loading of these files using HTTP, HTTPS,
FTP, or NFS (refer to the Product Reference Manual).
Notes:
Version 6.2
49
February 2011
MediaPack Series
¾ To use the Software Upgrade Wizard:
1.
Stop all traffic on the device (refer to the note above).
2.
Open the 'Software Upgrade Wizard' (Maintenance tab > Software Update menu >
Software Upgrade Wizard); the 'Software Upgrade Wizard' page appears.
Figure 3-9: Start Software Upgrade Wizard Page
3.
Click the Start Software Upgrade button; the 'Load a CMP file' Wizard page appears.
Figure 3-10: Load CMP File Wizard Page
Installation Manual
50
Document #: LTRT-59813
Installation Manual
3. Configuring the Device
Note: At this stage, you can quit the Software Update Wizard, by clicking Cancel
, without requiring a device reset. However, once you start uploading a
cmp file, the process must be completed with a device reset.
4.
Click the Browse button, navigate to the cmp file, and then click Send File; the cmp
file is loaded to the device and you're notified as to a successful loading.
5.
Click one of the following buttons:
•
•
Reset; the device resets with the newly loaded cmp, utilizing the existing
configuration and auxiliary files.
Next; the 'Load an ini File' wizard page opens.
Note that as you progress by clicking Next, the relevant file name corresponding to the
applicable Wizard page is highlighted in the file list on the left.
6.
7.
8.
Version 6.2
In the 'Load an ini File' page, you can now choose to either:
•
Click Browse, navigate to the ini file, and then click Send File; the ini file is
loaded to the device and you're notified as to a successful loading.
•
Use the ini file currently used by the device, by not selecting an ini file and by
ensuring that the 'Use existing configuration' check box is marked (default).
•
Return the device's configuration settings to factory defaults, by not selecting an
ini file and by clearing the 'Use existing configuration' check box.
You can now choose to either:
•
Click Reset; the device resets, utilizing the new cmp and ini file you loaded up to
now as well as utilizing the other auxiliary files.
•
Click Back; the 'Load a cmp file' page is opened again.
•
Click Next; the next page opens for loading the next consecutive auxiliary file
listed in the Wizard.
For loading the auxiliary files, follow the same procedure as for loading the ini file (Step
6).
51
February 2011
MediaPack Series
9.
In the 'FINISH' page, complete the upgrade process by clicking Reset; the device
'burns' the newly loaded files to flash memory and then resets the device. After the
device reset, the 'End Process' screen appears displaying the burned configuration
files (refer to the figure below).
Figure 3-11: End Process Wizard Page
10. Click End Process to close the wizard, and then in the 'Enter Network Password'
dialog box, enter your login user name and password and click OK; a message box
appears informing you of the new CMP file.
11. Click OK; the Web interface now becomes active and reflects the upgraded device.
Installation Manual
52
Document #: LTRT-59813
Installation Manual
3.7.2
3. Configuring the Device
Loading ini and Auxiliary Files
You can load the device with a configuration file (i.e., ini file) and Auxiliary files (e.g., Call
Progress Tones or Dial Plan files) for enhanced provisioning. For a detailed description of
the Auxiliary files, refer to the device's User's Manual.
Notes:
•
The current settings of parameters that are not included in the loaded ini
file are retained (incremental).
•
After loading the ini file, the device does not reset. Some files (e.g., Call
Progress Tones) are not changeable on-the-fly and require a device
reset.
•
Saving an auxiliary file to flash memory may disrupt traffic on the device.
To avoid this, disable all traffic on the device, by performing a graceful
lock (refer to 'Saving Configuration and Resetting the Device' on page
44).
•
You can also use BootP to load the auxiliary files to the device (refer to
the Product Reference Manual).
¾ To load an ini file and/or auxiliary files to the device:
1.
Open the 'Load Auxiliary Files' page (Maintenance tab > Software Update menu >
Load Auxiliary Files).
Figure 3-12: Load Auxiliary Files Page
2.
Version 6.2
Click the Browse button corresponding to the file type that you want to load, navigate
to the folder in which the file is located, and then click Open; the name and path of the
file appear in the field next to the Browse button.
53
February 2011
MediaPack Series
3.
Click the Load File button corresponding to the field that contains the file you want to
load.
4.
Save to flash memory and reset (if required) the device (refer to 'Saving and Resetting
the Device' on page 44).
Installation Manual
54
Document #: LTRT-59813
Installation Manual
4
4. Monitoring the Device
Monitoring the Device
You can monitor the operating status of the device by viewing one of the following:
4.1
„
Front-panel LEDs (refer to 'Front-Panel LEDs' on page 55).
„
Home page of the Web interface (refer to 'Web Interface' on page 56).
Front-Panel LEDs
The device’s operating status LEDs, located on the front panel are described in the tables
below:
Table 4-1: MP-11x Front-Panel LEDs Description
LED
Type
Color
Channels
Status
Telephone
Interface
Green
Uplink
Fail
Ready
Power
State
Definition
Blinking
Phone is ringing (incoming call, before answering).
Fast
Blinking
Line malfunction.
On
Off-hook or ringing.
-
Off
Normal on-hook position.
Ethernet
Link
Status
Green
On
Valid 10/100Base-TX Ethernet connection.
-
Off
No uplink.
Failure
Indication
Red
On
Failure (fatal error) or system initialization.
-
Off
Normal working condition.
Device
Status
Green
On
Device powered, self-test OK.
-
Off
Software loading or system failure.
Power
Supply
Status
Green
On
Power is received by the device.
Off
Failure / disruption in the AC power supply or power
is currently not being supplied to the device through
the AC power supply entry.
-
Table 4-2: MP-124 Front-Panel LEDs Description
Label
Type
Color
State
Ready
Device
Status
Green
On
Orange
Blinking
Red
On
Malfunction.
Ethernet
Link Status
Green
On
Valid 10/100Base-TX Ethernet connection.
Red
On
Malfunction.
Control
Link
Green
Blinking
-
-
LAN
Control
Version 6.2
Function
Device powered on, self-test OK.
Software loading/initialization.
Sending and receiving Protocol (SIP) messages.
No traffic.
55
February 2011
MediaPack Series
Label
Type
Color
State
Data
Packet
Status
Green
Blinking
Transmitting RTP packets.
Red
Blinking
Receiving RTP packets.
-
-
Green
On
Off-hook or ringing.
Red
On
Line malfunction.
-
-
Telephone
Interface
Channels
4.2
Function
No traffic.
Normal.
Web Interface
The Web interface’s Home page allows online monitoring of the device. This is provided by
a graphical display of the device’s front panel showing color-coded icons, depicting the
status of ports/channels and other interfaces. In addition, currently active alarms can also
be viewed.
4.2.1
Viewing Alarms
The 'Home' page provides a link to the 'Active Alarms' page, which lists all the device's
current alarms. This page is typically accessed using the following navigation path: Status
& Diagnostics tab > System Status menu > Carrier-Grade Alarms > Active Alarms.
¾ To view a list of current alarms:
„
In the 'Home' page, click the area labeled Alarms; the 'Active Alarms' page appears:
Figure 4-1: Current Alarms in Active Alarms Page
For each listed alarm, the following information is displayed:
•
Severity: severity level of the alarm:
♦
Critical (displayed in red)
♦
Major (displayed in orange)
♦
Minor (displayed in yellow)
♦
No alarm (displayed in green)
•
Source: element from which the alarm was generated
•
Description: brief explanation of the alarm
•
Date: date and time that the alarm was generated
Installation Manual
56
Document #: LTRT-59813
Installation Manual
4.2.2
4. Monitoring the Device
Viewing Channel Status
The 'Home' page displays channel port icons that indicate the voice channels' operating
status. You can use these port icons to drill down to view detailed channel status. For a
detailed description of the 'Home' page, refer to the device's User's Manual.
Figure 4-2: MP-11x Home Page
Figure 4-3: MP-124 Home Page
Table 4-3: Color-Coded Channel Status Icon Description
Icon State
Color
Description
Red
Line not connected (only applicable to FXO devices).
Gray
Channel inactive.
Blue
Handset is off-hook.
Green
Active RTP stream.
You can drill-down to view a detailed status of each channel.
¾ To view a detailed status of a channel:
1.
In the 'Home' page, click the port of whose status you want to view; a shortcut menu
appears.
2.
From the shortcut menu, choose Port Settings.
Version 6.2
57
February 2011
Installation Manual Ver. 6.2 www.audiocodes.com