Mega Motion ENDEAVOR X Owner`s manual

Owner’s Manual
Mega Motion Inc.
P.O. Box 275
Taylor, PA 18517-0275
1-800-MEGA-508
*INFMANU4333*
Mega Motion, Inc.
P.O. Box 275
Taylor, PA 18517-0275
www.mega-motion.com
SAFETY GUIDELINES
WARNING! An authorized Mega Motion Provider or qualified technician must perform the
initial setup of this scooter and must perform all of the procedures in this manual.
The symbols below are used throughout this owner's manual and on the scooter to identify warnings and
important information. It is very important for you to read them and understand them completely.
WARNING! Indicates a potentially hazardous condition/situation. Failure to follow
designated procedures can cause either personal injury, component damage or
malfunction. On the product, this icon is represented as a black symbol on a yellow
triangle with a black border.
MANDATORY! These actions should be performed as specified. Failure to perform
mandatory actions can cause personal injury and/or equipment damage. On the product,
this icon is represented as a white symbol on a blue dot.
PROHIBITED! These actions are prohibited. These actions should not be performed at
any time or in any circumstances. Performing a prohibited action can cause personal
injury and/or equipment damage. On the product, this icon is represented as a black
symbol with a red circle and a red slash.
Intended Use
The intended use of the Mega Motion device is to provide mobility to persons limited to a seated position
that have the capability of operating a powered scooter.
Please fill out the following information for quick reference:
Mega Motion Service Center:________________________________________________________
Address: ________________________________________________________________________
Phone Number:__________________________
Purchase Date: __________________________ Serial Number:____________________________
NOTE: This owner’s manual is compiled from the latest specifications and product information
available at the time of publication. We reserve the right to make changes as they become necessary. Any
changes to our products may cause slight variations between the illustrations and explanations in this
manual and the product you have purchased.
STOP DO NOT RETURN THIS PRODUCT TO THE
STORE. CALL 1-800-MEGA-508 FIRST.
Copyright © 2012
Mega Motion Inc.
INFMANU4333/Rev A/January 2012
CONTENTS
I.
INTRODUCTION .........................................................................................................................4
II.
SAFETY...........................................................................................................................................5
III. YOUR SCOOTER ......................................................................................................................19
IV. BATTERIES AND CHARGING ............................................................................................24
V.
OPERATION ..............................................................................................................................29
VI. COMFORT ADJUSTMENTS ...............................................................................................31
VII. DISASSEMBLY AND ASSEMBLY ....................................................................................34
VIII. BASIC TROUBLESHOOTING ..........................................................................................36
IX. CARE AND MAINTENANCE ..............................................................................................38
X.
WARRANTY ................................................................................................................................42
APPENDIX I - SPECIFICATIONS ................................................................................................44
Endeavor X
www.mega-motion.com
3
I. INTRODUCTION
SAFETY
Welcome to Mega Motion Inc. The product you have purchased combines state of the art components with
safety, comfort, and styling in mind. We are confident the design features will provide you with the
conveniences you expect during your daily activities. Understanding how to safely operate and care for
this product should bring you years of trouble free operations and service.
Read and follow all instructions, warnings, and notes in this manual before attempting to operate this
product for the first time. You must also read all instructions, warnings, and notes contained in any
supplemental instructional booklets that accompanied your scooter before initial operation. In addition,
your safety depends upon you, as well as your provider, caregiver, or healthcare professional in using good
judgement.
If there is any information in this manual which you do not understand, or if you require additional
assistance for setup or operation, please contact 1-800-MEGA-508. Failure to follow the instructions,
warnings, and notes in this manual and those located on your Mega Motion product can result in
personal injury or product damage and will void Mega Motion’s product warranty.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter, or modify this product
or remove or render inoperable or unsafe any guards, shields, or other safety features of this product; fail,
refuse, or neglect to install any retrofit kits from time to time provided by Mega Motion to enhance or
preserve the safe use of this product.
SHIPPING AND DELIVERY
Before using your scooter, make sure your delivery is complete as some components may be individually
packaged. If you do not receive a complete delivery, please contact Mega Motion immediately. Where
damage has occurred during transport, either to the packaging or content, please contact the delivery
company responsible.
INFORMATION EXCHANGE
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear
about the safety and reliability of your new scooter, and about the service you received from Mega Motion.
Please notify us of any change of address, so we can keep you apprised of important information about
safety, new products, and new options that can increase your ability to use and enjoy your scooter. Please
feel free to contact us at the address below:
Mega Motion Inc.
P.O. Box 275
Taylor, PA 18517-0275
1-800-MEGA-508
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact
us and we will be glad to send you a new one immediately.
4
www.mega-motion.com
Endeavor X
II. SAFETY
PRODUCT SAFETY SYMBOLS
The symbols below are used on the scooter to identify warnings, mandatory actions, and prohibited
actions. It is very important for you to read and understand them completely.
Pinch/Crush points created during assembly.
Corrosive chemicals contained in battery.
EMI/RFI - This product has been tested and passed at an immunity level of 20 V/m.
Explosive conditions exist!
Do not expose to heat sources such as open flame or sparks. Do not transport
batteries with flammable or combustible items.
Fully charge batteries before operating.
Remove key from an unattended scooter.
Read and follow the information in the owner’s manual.
Keep tools and other metal objects away from battery terminals. Contact with
tools can cause electrical shock.
Endeavor X
www.mega-motion.com
5
II. SAFETY
Maximum seating weight.
Unlocked and in freewheel mode.
Place unit on level ground and stand to one side when changing from drive mode
to freewheel mode or freewheel mode to drive mode.
Locked and in drive mode.
Front-to-rear plug orientation.
Battery posts, terminals, and related accessories contain lead and lead
compounds. Wear goggles and gloves when handling batteries and wash hand
after handling.
Do not place the scooter in freewheel mode when on an incline or decline.
Not a brake.
6
www.mega-motion.com
Endeavor X
II. SAFETY
Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive
conditions.
Do not remove anti-tip wheels.
Do not use a cell phone, walkie/talkie, laptop, or other radio transmitter while
operating.
Avoid exposure to rain, snow, ice, salt, or standing water whenever possible.
Maintain and store in a clean and dry condition.
This scooter does not meet ISO 7176-19 requirements for transport of an
occupied scooter in a motor vehicle.
Manufactured in.
Removal of grounding prong can create electrical hazard. If necessary, properly
install an approved 3-pronged adapter to an electrical outlet having 2-pronged
plug access.
Do not connect an extension cord to the AC/DC converter or the battery charger.
Endeavor X
www.mega-motion.com
7
II. SAFETY
Do not allow unsupervised children to play near the scooter while the batteries
are charging.
Do not use batteries with different amp-hour (Ah) capacities. Do not mix old and
new batteries. Always replace both batteries at the same time.
Keep your hands away from the tires when driving. Be aware that loose fitting
clothing can become caught in drive tires.
Battery charger for indoor use only.
Disposal and recycling - Contact your authorized Mega Motion Provider for
information on proper disposal and recycling of your Mega Motion product and its
packaging.
Indicates electrical shock hazard.
Do not mix AGM or Gel-Cell batteries. Always use batteries of the same type and
chemistry.
Indicates scooter attachment points.
8
www.mega-motion.com
Endeavor X
II. SAFETY
GENERAL
MANDATORY! Do not operate your new scooter for the first time without completely
reading and understanding this owner’s manual.
Your scooter is a state-of-the-art life-enhancement device designed to increase mobility. Mega Motion
provides an extensive variety of products to best fit the individual needs of the scooter user. Please be
aware that the final selection and purchasing decision regarding the type of scooter to be used is the responsibility of the scooter user who is capable of making such a decision and his/her healthcare professional
(i.e., medical doctor, physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted
the scooter to the user and has assisted the prescribing healthcare professional and/or the authorized Mega
Motion Provider in the instruction process for the use of the product.
There are certain situations, including some medical conditions, where the scooter user will need to practice operating the scooter in the presence of a trained attendant. A trained attendant can be defined as a
family member or care professional specially trained in assisting a scooter user in various daily living
activities.
As you begin using your scooter during daily activities, you will probably encounter situations in which
you will need some practice. Simply take your time and you will soon be in full and confident control as
you maneuver through doorways, on and off elevators, up and down ramps, and over moderate terrain.
Below are some precautions, tips, and other safety considerations that will help the user become accustomed to operating the scooter safely.
MODIFICATIONS
Mega Motion has designed and engineered your scooter to provide maximum mobility and utility. A wide
range of accessories is available from your authorized Mega Motion Provider to further customize your
scooter to better suit your needs and/or preferences. However, under no circumstances should you modify,
add, remove, or disable any feature, part, or function of your scooter.
WARNING! Do not modify your scooter in any way not authorized by Mega Motion. Do not
use accessories if they have not been tested or approved for Mega Motion products.
REMOVABLE PARTS
WARNING! Do not attempt to lift or move your scooter by any of its removable parts,
including the armrests, seat, or shroud. Mega Motion recommends use of only solid, nonremovable frame components such as scooter securement points or the front and rear
frame weldments to lift or move your scooter.
WARNING! Lifting the scooter should be accomplished with no fewer than three people,
one at the front and two at the rear of the unit.
PRE-RIDE SAFETY CHECK
Get to know the feel of your scooter and its capabilities. Mega Motion recommends that you perform a
safety check before each use to make sure your scooter operates smoothly and safely.
Endeavor X
www.mega-motion.com
9
II. SAFETY
Perform the following inspections prior to using your scooter:
Check for proper tire inflation. Maintain but do not exceed the psi/bar/kPa air pressure rating indicated
on each tire if equipped with pneumatic tires.
Check all electrical connections. Make sure they are tight and not corroded.
Check all harness connections. Make sure they are secured properly.
Check the brakes.
Check battery charge.
If you discover a problem, contact your authorized Mega Motion Provider for assistance.
TIRE INFLATION
If your scooter is equipped with pneumatic tires, you should check or have the air pressure checked at least
once a week. Proper inflation pressures will prolong the life of your tires and help ensure the smooth
operation of your scooter.
WARNING! It is critically important that the psi/bar/kPa air pressure rating indicated on
each tire be maintained in pneumatic tires at all times. Do not underinflate or overinflate
your tires. Low pressure may result in loss of control, and overinflated tires may burst.
Failure to maintain the psi/bar/kPa air pressure rating indicated on pneumatic tires at all
times may result in tire and/or wheel failure.
WARNING! Inflate your scooter tires from a regulated air source with an available
pressure gauge. Inflating your tires from an unregulated air source could overinflate
them, resulting in a burst tire.
NOTE: If the tires on your scooter list the psi rating only, use the following conversion formulas to find
the bar or kPa rating: bar = psi x 0.06895, kPa = psi x 6.89476
WEIGHT LIMITATIONS
Your scooter is rated for a maximum weight capacity. Refer to the specifications table for information.
Keep in mind that the maximum weight capacity includes the combined weight of the user and any
accessories mounted to the scooter.
MANDATORY! Stay within the specified weight capacity for your scooter. Exceeding the
weight capacity voids your warranty. Mega Motion will not be held responsible for
injuries and/or property damage resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your scooter. Carrying passengers on your
scooter may affect the center of gravity, resulting in a tip or a fall.
INCLINE INFORMATION
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe
access. Some ramps may have turning switchbacks (180-degree turns) that require you to have good cornering skills on your scooter.
Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
Take wide swings with your scooter around any tight corners. If you do that, the scooter’s rear wheels
will follow a wide arc, not cut the corner short, and not bump into or get hung up on any railing corners.
When driving down a ramp, keep the scooter’s speed adjustment set to the slowest speed setting to
ensure a safely controlled descent.
Avoid sudden stops and starts.
10
www.mega-motion.com
Endeavor X
II. SAFETY
When climbing an incline, try to keep your scooter moving. If you must stop, start up again slowly, and
then accelerate cautiously. When driving down an incline, do so by setting the speed adjustment dial to the
slowest setting and driving in the forward direction only. If your scooter starts to move down the incline
faster than you anticipated or desired, allow it to come to a complete stop by releasing the throttle control
lever. Then push the throttle control lever forward slightly to ensure a safely controlled descent.
WARNING! When on any sort of an incline or decline, never place the scooter in
freewheel mode especially while seated on it or standing next to it.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the
face of the incline. Drive your scooter straight up the incline. This greatly
reduces the possibility of a tip or a fall. Always exercise extreme caution when
negotiating an incline.
WARNING! Do not drive your scooter across the side of an incline or diagonally
up or down an incline; do not stop, if possible, while driving up or down an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e.,
areas covered with snow, ice, cut grass, or wet leaves).
WARNING! Even though your scooter is capable of climbing slopes greater than
those listed in Specifications Appendix, do not, under any circumstances, exceed
the incline guidelines or any other specifications. Doing so could cause instability
in your scooter.
Handicap public access ramps are not subject to government regulation in all countries, and therefore do
not necessarily share the same standard percent of slope. Other inclines may be natural or, if man-made,
not designed specifically for scooters.
Tests were conducted with the scooter’s seat in the highest position and adjusted rearward on the seat base
to its farthest rearward position. Use the specification table information as a guideline. See Section
“Appendix I - Specifications.” Your scooter’s ability to travel up inclines is affected by your weight, your
scooter’s speed, your angle of approach to the incline and your scooter setup.
WARNING! Any attempt to climb or descend a slope steeper than what is listed in the
Specifications Appendix may put your scooter in an unstable position and cause it to tip.
WARNING! Never carry an oxygen tank weighing more than 13 lbs. (6 kg). Never fill the
front or rear basket with contents exceeding 13 lbs. (6 kg).
Endeavor X
www.mega-motion.com
11
II. SAFETY
When you approach an incline, it is best to lean forward. See figures 1 and 2. This shifts the center of
gravity of you and your scooter toward the front of the scooter for improved stability.
NOTE: When negotiating ramps, if the throttle control lever is released while moving forward, the
powered scooter may "roll back" approximately 3 feet (1 meter) before the brake engages. If the throttle
control lever is released while moving in reverse, the powered scooter may "roll back" approximately
3 feet (1 meter) before the brake engages.
Figure 1. Normal Driving Position
Figure 2. Increased Stability Driving Position
CORNERING INFORMATION
Excessively high cornering speeds can create the possibility of tipping. Factors which affect the possibility
of tipping include, but are not limited to, cornering speed, steering angle (how sharply you are turning),
uneven road surfaces, inclined road surfaces, riding from an area of low traction to an area of high traction
(such as passing from a grassy area to a paved area – especially at high speed while turning), and abrupt
directional changes. High cornering speeds are not recommended. If you feel that you may tip over in a
corner, reduce your speed and steering angle (i.e., lessen the sharpness of the turn) to prevent your scooter
from tipping.
WARNING! When cornering sharply, reduce your speed and maintain a stable center of
gravity. When using your scooter at higher speeds, do not corner sharply. This greatly
reduces the possibility of a tip or fall.
BRAKING INFORMATION
Your scooter is equipped with these powerful brake systems:
Regenerative: Uses electricity to rapidly slow the vehicle when the throttle control lever returns to the
center/stop position.
Disc Park Brake: Activates mechanically after regenerative braking slows the vehicle to near stop, or
when power is removed from the system for any reason.
12
www.mega-motion.com
Endeavor X
II. SAFETY
OUTDOOR DRIVING SURFACES
Your scooter is designed to provide optimum stability under normal driving conditions—dry, level
surfaces composed of concrete or asphalt. However, Mega Motion recognizes that there will be times
when you will encounter other surface types. For this reason, your scooter is designed to perform
admirably on packed soil, grass, and gravel. Feel free to use your scooter safely on lawns and in park areas.
Avoid driving on uneven terrain and/or soft surfaces.
Avoid tall grass that can become tangled in the running gear.
Avoid loosely packed gravel and sand.
Do not use your scooter in fresh or salt water.
Do not use your scooter at the edge of a stream, lake, or ocean.
If you feel unsure about a driving surface, avoid that surface.
PUBLIC STREETS AND ROADWAYS
WARNING! You should not operate your scooter on public streets and roadways. Be
aware that it may be difficult for traffic to see you when you are seated on your scooter.
Obey all local pedestrian traffic rules. Wait until your path is clear of traffic, and then
proceed with extreme caution.
STATIONARY OBSTACLES (STEPS, CURBS, ETC.)
WARNING! Do not drive near raised surfaces, unprotected ledges, and/or drop-offs (curbs,
porches, stairs, etc.).
WARNING! Do not attempt to have your scooter climb or descend an obstacle that is
inordinately high.
WARNING! Do not attempt to have your scooter proceed backward down any step, curb,
or other obstacle. This may cause the scooter to tip.
WARNING! Be sure your scooter is traveling perpendicular to any curb you may be
required to ascend or descend. See figures 3 and 3A.
WARNING! Even though your scooter may be capable of handling greater obstacles,
Mega Motion recommends that you do not attempt to negotiate a curb that has a height
greater than 2 in. (5 cm). Doing so could cause instability in your scooter.
CURB
CURB
Figure 3. Correct Curb Approach
Endeavor X
Figure 3A. Incorrect Curb Approach
www.mega-motion.com
13
II. SAFETY
INCLEMENT WEATHER PRECAUTIONS
Exposure of your scooter to inclement weather conditions should be avoided whenever possible. If suddenly caught up in rain, snow, severe cold or heat while operating your scooter, proceed to shelter at the
earliest opportunity. Thoroughly dry your scooter before storing, charging, or operating your scooter.
PROHIBITED! Operating in rain, snow, salt, mist/spray conditions, and on icy/slippery
surfaces can cause damage to the scooter and electrical system. Maintain and store
your scooter in a dry and clean condition.
WARNING! Prolonged exposure to hot or cold conditions may affect the temperature of
upholstered and non-upholstered items on the scooter, possibly resulting in skin
irritation. Exercise caution when using your scooter in extremely hot or cold conditions
or when exposing your scooter to direct sunlight for prolonged periods of time.
FREEWHEEL MODE
Your scooter is equipped with a manual freewheel lever that, when engaged, allows the scooter to be
pushed. For more information about how to place your scooter into and out of freewheel mode, see III.
“Your Scooter.”
WARNING! When your scooter is in freewheel mode, the braking system is disengaged.
Disengage the drive motors only on a level surface.
Ensure the key is removed from the key switch.
Stand to the side of the scooter to engage or disengage freewheel mode. Never sit
on a scooter to do this.
After you have finished pushing your scooter, always return it to the drive mode to
lock the brakes.
An added feature built into the scooter is “push-too-fast” protection which safeguards the scooter against
gaining excessive speed while in freewheel mode.
“Push-too-fast” operates differently depending on which of two conditions exists:
If the key is switched “off” while in freewheel mode, the scooter’s controller activates regenerative
braking when the scooter is pushed faster than a maximum threshold which has been preprogrammed.
In this case, the controller is acting as a speed governor.
If the key is switched “on” while in freewheel mode, you will encounter considerable resistance at any
speed. This prevents the scooter from gaining unwanted momentum should the manual freewheel lever
inadvertently be released while driving the scooter.
WARNING! Mega Motion recommends that you do not disconnect the batteries when the
scooter is in freewheel mode as this may interfere with the function of the controller.
STAIRS AND ESCALATORS
Scooters are not designed to travel up or down stairs or escalators. Always use an elevator.
WARNING! Do not use your scooter to negotiate steps or escalators.
DOORS
Determine if the door opens toward or away from you.
Use your hand to turn the knob or push the handle or push-bar.
Drive your scooter gently and slowly forward to push the door open. Or drive your scooter gently and
slowly backwards to pull the door open.
14
www.mega-motion.com
Endeavor X
II. SAFETY
ELEVATORS
Modern elevators have a door edge safety mechanism that, when pushed, reopens the door(s).
If you are in the doorway of a elevator when the door(s) begin to close, push on the rubber door edge
or allow the rubber door edge to contact the scooter and the door will reopen.
Use care that pocketbooks, packages, or scooter accessories do not become caught in elevator doors.
NOTE: If your scooter’s turning radius is greater than 60 in. (152.4 cm), it may be difficult to maneuver
in elevators and building entrances. Use caution when attempting to turn or maneuver your scooter in
small spaces, and avoid areas that might pose a problem.
LIFT/ELEVATION PRODUCTS
If you will be transporting your scooter during travel, you may find it necessary to use a vehicle-mounted
lift system or elevation product to aid in transportation. Mega Motion recommends that you closely review
the warnings, instructions, specifications, and safety information set forth by the manufacturer of the lift/
elevation product before using that product.
WARNING! Not all lift systems/elevation products are rated for use with an occupied
mobility device. Mega Motion recommends that you do not remain seated in your scooter
when it is being used in connection with any type of lift system/elevation product unless:
That product is rated for occupied use by the manufacturer.
You are able to occupy your mobility device in strict conformity with the warnings,
instructions, specifications, and safety guidelines set forth by the manufacturer.
WARNING! Always turn off the power to the unit when you are being transferred via an
elevation product. Failure to do so may result in accidental throttle control lever contact,
resulting in unintended movement and personal injury or product damage.
BATTERIES
In addition to following the warnings below, be sure to comply with all other battery handling information.
MANDATORY! Battery posts, terminals, and related accessories contain lead
and lead compounds. Wear goggles and gloves when handling batteries and
wash hands after handling.
WARNING! Scooter batteries are heavy. See specifications table. If you are
unable to lift that much weight, be sure to get help. Use proper lifting techniques
and avoid lifting beyond your capacity.
WARNING! Always protect the batteries from freezing and never charge a frozen
battery. Charging a frozen battery may result in damage to the battery.
WARNING! Connect the battery harnesses in the proper manner. RED (+) cables
must be connected to positive (+) battery terminals/posts. BLACK (-) cables must
be connected to negative (-) battery terminals/posts. Protective caps should be
installed over all battery terminals. REPLACE cables immediately if damaged.
BATTERY DISPOSAL AND RECYCLING
If you encounter a damaged or cracked battery, immediately enclose it in a plastic bag and contact your
local waste disposal agency or authorized Mega Motion Provider for instructions on disposal and battery
recycling, which is our recommended course of action.
Endeavor X
www.mega-motion.com
15
II. SAFETY
PREVENTING UNINTENDED MOVEMENT
WARNING! If you anticipate being seated in a stationary position for an extended period
of time, turn off the power. This will prevent unexpected motion from inadvertent throttle
control lever contact.
MOTOR VEHICLE TRANSPORT
Mega Motion recommends that you do not remain seated in your scooter while traveling in a motor
vehicle. The scooter should be stowed in the trunk of a car or in the back of a truck or van with batteries
removed and/or properly secured. In addition, all removable scooter parts, including the armrests, seat, and
shroud should be removed and/or properly secured during motor vehicle transport.
WARNING! Although your scooter may be equipped with a positioning belt, this belt is not
designed to provide proper restraint during motor vehicle transport. Anyone traveling in
a motor vehicle should be properly secured in the motor vehicle seat with safety belts
fastened securely.
WARNING! Do not sit on your scooter while it is in a moving vehicle.
WARNING! Always be sure your scooter and its batteries are properly secured when it is
being transported. Batteries should be secured in an upright position and protective caps
should be installed on the battery terminals. Batteries should not be transported with any
flammable or combustible items.
GETTING ONTO AND OFF OF YOUR SCOOTER
Getting onto and off of your scooter requires a good sense of balance. Please observe the following safety
tips when getting onto and off of your scooter:
Remove the key from the key switch.
Ensure that your scooter is not in freewheel mode. See III. “Your Scooter.”
Make certain that the seat is fixed into place.
Pivot the armrests up to make getting onto and off of the scooter easier.
WARNING! Position yourself as far back as possible in the scooter seat to prevent the
scooter from tipping.
WARNING! Avoid putting all of your weight on the scooter armrests and do not use the
armrests for weight bearing purposes, such as transfers. Such use may cause the
scooter to tip, resulting in a fall from the scooter.
WARNING! Avoid putting all of your weight on the floorboard. Such use may cause the
scooter to tip.
16
www.mega-motion.com
Endeavor X
II. SAFETY
REACHING AND BENDING
Avoid reaching or bending while driving your scooter. Bending forward creates the risk of accidental
throttle control lever contact. Bending to the side while seated creates the risk of tipping. It is important to
maintain a stable center of gravity and keep the scooter from tipping. Mega Motion recommends that the
scooter user determine his/her personal limitations and practice bending and reaching in the presence of a
qualified attendant.
WARNING! Do not bend, lean, or reach for objects if you have to pick them up from the
scooter deck or from either side of the scooter. Movements such as these may change
your center of gravity and the weight distribution of the scooter and cause your scooter
to tip.
PROHIBITED! Keep your hands away from the tires when driving. Be aware that loose
fitting clothing can become caught in drive tires.
POSITIONING BELTS
Your authorized Mega Motion Provider, therapist(s), and other healthcare professionals are responsible
for determining your requirement for a positioning belt in order to operate your scooter safely.
WARNING! If you require a positioning belt to safely operate your scooter, make sure it
is fastened securely. Serious personal injury may result if you fall from the scooter.
PRESCRIPTION DRUGS/PHYSICAL LIMITATIONS
The scooter user must exercise care and common sense when operating his/her scooter. This includes
awareness of safety issues when taking prescribed or over-the-counter drugs or when the user has specific
physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter
medication or if you have certain physical limitations. Some medications and limitations
may impair your ability to operate your scooter in a safe manner.
ALCOHOL/SMOKING
The scooter user must exercise care and common sense when operating his/her scooter. This includes
awareness of safety issues while under the influence of alcohol or while smoking.
WARNING! Do not operate your scooter while you are under the influence of alcohol, as
this may impair your ability to drive safely.
WARNING! Mega Motion strongly recommends that you do not smoke cigarettes while
seated in your scooter, although the scooter has passed the necessary testing
requirements for cigarette smoking. You must adhere to the following safety guidelines
if you decide to smoke cigarettes while seated in your scooter.
Do not leave lit cigarettes unattended.
Keep ashtrays a safe distance from the seat cushions.
Always make sure cigarettes are completely extinguished before disposal.
Endeavor X
www.mega-motion.com
17
II. SAFETY
FLAMMABILITY PRECAUTIONS
WARNING! Even though the plastics used on your scooter have been tested and have
passed the applicable flammability standards, Mega Motion recommends that you do not
expose your scooter to open flames.
WARNING! Replace worn or damaged upholstery immediately to reduce the risk of fire
hazard.
WARNING! Be aware that washing of upholstered items may reduce the resistance to
flammability of the fabric.
ELECTROMAGNETIC AND RADIO FREQUENCY INTERFERENCE (EMI/RFI)
WARNING! Laboratory tests have shown that electromagnetic and radio frequency
waves can have an adverse effect on the performance of electrically-powered mobility
vehicles.
Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones, mobile
two-way radios (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters,
wireless computer links, microwave signals, paging transmitters and medium-range mobile transceivers
used by emergency vehicles. In some cases, these waves can cause unintended movement or damage to
the control system. Every electrically-powered mobility vehicle has an immunity (or resistance) to EMI.
The higher the immunity level, the greater the protection against EMI. This product has been tested and
has passed at an immunity level of 20 V/M.
WARNING! Be aware that cell phones, two-way radios, laptops, and other types of radio
transmitters may cause unintended movement of your electrically-powered mobility
vehicle due to EMI. Exercise caution when using any of these items while operating your
mobility vehicle and avoid coming into close proximity of radio and TV stations.
WARNING! The addition of accessories or components to the electrically-powered
mobility vehicle can increase the susceptibility of the vehicle to EMI. Do not modify your
scooter in any way not authorized by Mega Motion.
WARNING! The electrically-powered mobility vehicle itself can disturb the performance
of other electrical devices located nearby, such as alarm systems.
NOTE: If unintended motion or brake release occurs, turn your scooter off as soon as it is safe to do
so. Call Mega Motion at 1-800-MEGA-508 to report the incident.
18
www.mega-motion.com
Endeavor X
III. YOUR SCOOTER
TILLER CONSOLE
The tiller console houses all of the controls needed to drive your scooter, including the speed adjustment
dial, throttle control lever, battery condition meter, lights switch, hazard lights switch and horn buttons.
See figure 4.
PROHIBITED! Do not expose the tiller console to moisture. In the event that the tiller
console does become exposed to moisture, do not attempt to operate your scooter until
the tiller console has dried thoroughly.
BATTERY CONDITION METER
SPEED ADJUSTMENT DIAL
KEY SWITCH
THROTTLE
CONTROL
LEVER
THROTTLE
CONTROL
LEVER
HORN BUTTON
LIGHTS SWITCH
HORN BUTTON
Figure 4. Tiller Console
Horn Buttons
These buttons activate a warning horn. Your scooter must be powered up for the horn to be operational.
Do not hesitate to use the warning horn when doing so may prevent accident or injury.
Key Switch
Insert the key into the key switch and turn it clockwise to power up (turn on) your scooter.
Turn the key counterclockwise to power down (turn off) your scooter.
WARNING! If the key is moved to the “off” position while your scooter is in motion, the
electronic brakes will engage and your scooter will come to an abrupt stop!
Battery Condition Meter
When the key is fully inserted and turned clockwise to power up your scooter, this meter indicates the
approximate battery voltage strength. For further information on battery charging, see IV. “Batteries and
Charging.”
Endeavor X
www.mega-motion.com
19
III. YOUR SCOOTER
Lights Switch
This switch controls your scooter’s lights.
Toggle the switch forward to turn on your scooter’s front top light and running lights.
Toggle the switch rearward to turn on all the scooters lights (upper and lower front and running lights).
WARNING! Scooter users are required to use their lights when visibility is restricted—day
or night.
Throttle Control Lever
This lever allows you to control the forward speed and the reverse speed of your scooter up to the
maximum speed you preset with the speed adjustment dial.
To move forward, use your right thumb to push the right side of the throttle control lever.
To move rearward, use your left thumb to push the left side of the throttle control lever.
Release the throttle control lever and allow your scooter to come to a complete stop before engaging the
other side of the lever. When the throttle control lever is completely released, it automatically returns to
the center “stop” position and engages your scooter’s brakes.
Speed Adjustment Dial
This dial allows you to preselect and limit your scooter’s top speed.
The image of the tortoise represents the slowest speed setting.
The image of the hare represents the fastest speed setting.
Off-board Charger Port
The off-board charger power cord plugs into this port when charging the batteries. See figure 5.
OFF-BOARD CHARGER PORT
Figure 5. Off-board Charger Port
20
www.mega-motion.com
Endeavor X
III. YOUR SCOOTER
Tiller Console Fuses
These fuses help protect your scooter’s front lighting
and key switch console systems from receiving an
overload of electrical current. The fuses used in your
scooter are the same type used in automobiles. See
figure 6. See IX. “Care and Maintenance” for fuse
replacement.
SPARE
UPPER HEAD LIGHT
LOWER HEAD LIGHT
REAR COMPONENTS
The batteries, the main circuit breaker (reset button),
the manual freewheel lever, the anti-tip wheels, and the
motor/transaxle assembly are located on the rear
section of your scooter. See figure 7.
Anti-Tip Wheels
The anti-tip wheels are an integral and important safety
feature of your scooter. They are bolted to the frame at
the rear of the scooter.
SPARE
SPARE
Figure 6. Tiller Console Fuses
PROHIBITED! Do not remove the anti-tip wheels or modify your scooter in any way that
is not authorized by Mega Motion.
WARNING! The anti-tip wheels may cause interference with the smooth transition of your
scooter when ascending or descending a curb. Contact your authorized Mega Motion
Provider for more information.
Batteries
The batteries store the electrical energy that powers your scooter. See IV. “Batteries and Charging ” for
information on how to charge your scooter batteries.
Motor/Transaxle Assembly
The motor/transaxle assembly is an electromechanical unit that converts electrical energy from your
scooter’s batteries into the controlled mechanical energy that drives the scooter’s wheels.
BATTERY
BATTERY
MANUAL FREEWHEEL LEVER
MOTOR/TRANSAXLE ASSEMBLY
ANTI-TIP WHEELS
Figure 7. Rear Components
Endeavor X
www.mega-motion.com
21
III. YOUR SCOOTER
Safety Flag Bracket (Optional)
An accessory bracket for installing an optional safety
flag is mounted near each anti-tip wheel and also on
the seatback hinge. To install the flag to the rear
frame, use the smaller of the two supplied “L” shaped
hex keys. To install the flag to the seat hinge, use the
larger hex key. See figure 8.
HEX KEY
CAP
SETSCREW
To install the flag:
1. Remove the cap from the top of the bracket.
2. Loosen the setscrew with the supplied “L”
shaped hex key.
3. Insert the flag pole into the opening.
4. Tighten the setscrew to complete installation.
Manual Freewheel Lever
Whenever you need or want to push your scooter for
short distances, you can put it in freewheel mode.
Remove the key from the key switch.
Push forward on the manual freewheel lever to
disable the drive system and the brake system.
You may now push your scooter.
Pull back on the manual freewheel lever to
reengage the drive and the brake systems and
take your scooter out of freewheel mode.
WARNING! When your scooter is in
freewheel mode, the braking system
is disengaged.
Disengage the drive motors only
on a level surface.
Ensure the key is removed from
the key switch.
Stand to the side of the scooter
to
engage
or
disengage
freewheel mode. Never sit on a
scooter to do this.
After you have finished pushing
your scooter, always return it to
the drive mode to
lock
the
brakes.
Figure 8. Safety Flag Bracket
MAIN CIRCUIT BREAKER (RESET BUTTON)
Figure 9. Main Circuit Breaker Reset Button
NOTE: If the scooter is placed in freewheel mode
(manual freewheel lever forward) while the key is in
the “on” position, the scooter will not run until the
manual freewheel lever is pushed backward and the
key is turned to the “off” position, then back to the
“on” position.
22
www.mega-motion.com
Endeavor X
III. YOUR SCOOTER
Main Circuit Breaker (Reset Button)
When the voltage in the batteries becomes low or your scooter is heavily strained because of excessive
loads, the main circuit breaker may trip to protect the motor and electronics from damage. When the
breaker trips, the entire electrical system shuts down. See figure 9.
The reset button pops out when the breaker trips.
Allow a minute or so for the electronics to “rest.”
Push in the reset button to reset the breaker.
If the breaker trips frequently, you may need to charge the batteries more often or have your authorized
Mega Motion Provider perform a load test on the batteries.
SECUREMENT POINTS
Always secure the scooter in a forward-facing position in the vehicle. Attach the four tie-down straps to
the designated securement points. See figures 10, 10A, and 10B. Tighten the straps to sufficiently remove
all slack. Never attach tie-downs to adjustable, moving, or removable parts of the scooter such as armrests,
shrouds, and wheels. These items should be removed. Position the anchor points for the rear tie-down
straps directly behind the rear securement points on the scooter. The front tie-down straps should anchor
to floor points that are spaced wider than the scooter to provide increased lateral stability.
WARNING! Do not leave the scooter in freewheel mode when securing it for transport.
WARNING! Ensure scooters are properly secured to the motor vehicle during transport.
Scooters that are not properly secured can become a hazard to the user and to other
vehicle passengers in the event of a crash, sudden stopping, or swerving, as the scooter
could tip or slide out of place.
SECUREMENT POINTS
SECUREMENT POINTS
Figure 10. Rear Securement Points
Endeavor X
Figure 10A. Front
Points (3-wheel)
SECUREMENT POINTS
Securement Figure 10B. Front Securement Points
(4-wheel)
www.mega-motion.com
23
IV. BATTERIES AND CHARGING
BATTERIES AND CHARGING
Your scooter requires two long-lasting, 12-volt, deep-cycle batteries
that are sealed and maintenance free. They are recharged by an offboard charging system.
Charge your scooter’s batteries fully prior to using it for the first
time.
Keep the batteries fully charged to keep your scooter running
smoothly.
READING YOUR BATTERY VOLTAGE
The battery condition meter on the tiller console indicates the
approximate strength of your batteries using a color code. From right
to left, green indicates fully charged batteries, yellow indicates a
draining charge, and red indicates that an immediate recharge is
necessary. See figure 11. To ensure the highest accuracy, the battery
condition meter should be checked while operating your scooter at full
speed on a dry, level surface.
Figure 11. Battery Condition Meter
CHARGING YOUR BATTERIES
PROHIBITED! Never use an extension cord to plug in your battery charger. Plug the
charger directly into a properly wired standard electrical outlet.
PROHIBITED! Removal of the grounding prong can create an electrical hazard. If
necessary, properly install an approved 3-pronged adapter to an electrical outlet having
2-pronged plug access.
PROHIBITED! Do not allow unsupervised children to play near the scooter while the
batteries are charging. Mega Motion recommends that you do not charge the batteries
while the scooter is occupied.
MANDATORY! Read the battery charging instructions in this manual and in the manual
supplied with the battery charger before charging the batteries.
WARNING! Explosive gases may be generated while charging the batteries. Keep the
scooter and the battery charger away from sources of ignition such as flames or sparks
and provide adequate ventilation when charging the batteries.
WARNING! You must recharge your scooter’s batteries with the supplied off-board
charger. Do not use an automotive-type battery charger.
WARNING! Ensure that both ends of the charger power cord are clean and dry before
plugging the charger power cord into the off-board charger port or the electrical outlet.
WARNING! Inspect the battery charger, wiring, and connectors for damage before each
use. Contact your authorized Mega Motion Provider if damage is found.
WARNING! Do not attempt to open the battery charger case. If the battery charger does
not appear to be working correctly, contact your authorized Mega Motion Provider.
WARNING! If the off-board battery charger is equipped with cooling slots, then do not
attempt to insert objects through these slots.
WARNING! Be aware that the battery charger case may become hot during charging.
Avoid skin contact and do no place on surfaces that may be affected by heat.
24
www.mega-motion.com
Endeavor X
IV. BATTERIES AND CHARGING
WARNING! If your off-board battery charger has not been tested and approved for outdoor
use, then do not expose it to adverse or extreme weather conditions. If the battery
charger is exposed to adverse or extreme weather conditions, then it must be allowed to
adjust to the difference in environmental conditions before use indoors. Refer to the
manual supplied with the battery charger for more information.
Follow these easy steps to charge your batteries
safely:
1. Position your scooter close to a standard
electrical outlet.
2. Remove the key from the key switch.
3. Make certain that the manual freewheel lever is
in the drive (down) position.
4. Plug the 3-pin charger power cord into the offboard charger port. See figures 5 and 12.
5. Extend the charger power cord and plug it into
the electrical outlet. We recommend that you
charge the batteries for 8 to 14 hours.
6. When the batteries are fully charged, unplug the
charger power cord from the electrical outlet and
then from the off-board charger port.
PLUGS INTO THE OFF-BOARD CHARGER PORT
PLUGS INTO WALL OUTLET
Figure 12. Off-board Charger
NOTE: The LED lights on the charger indicate different charger conditions at various times: charger
power on, charging in progress, and charging complete. Refer to the manual supplied with the charger
for a complete explanation of these indicators.
NOTE: There is a charger inhibit function on your scooter. The scooter will not run and the battery
condition meter will not operate while the batteries are charging.
FREQUENTLY ASKED QUESTIONS
How does the charger work?
When your scooter’s battery voltage is low, the charger works harder, sending more electrical current to
the batteries to bring up their charge. As the batteries approach a full charge, the charger sends less and
less electrical current. When the batteries are fully charged, the current sent from the charger is at nearly
zero amperage. Therefore, when the charger is plugged in, it maintains the charge on your scooter’s batteries, but does not overcharge them. Refer to the manual supplied with the battery charger for charging
instructions.
Can I use a different charger?
Chargers are selected precisely for particular applications and are especially matched to the type, size, and
chemical formulation of specific batteries. For the safest and most efficient charging of your scooter’s
batteries, we recommend use of the charger supplied as original equipment with your Mega Motion
product only. Any charging method resulting in batteries being charged individually is especially
prohibited.
What if my scooter’s batteries won’t charge?
Ensure the red (+) and black (-) battery cables are connected properly to the battery terminals.
Ensure both battery harnesses that extend from the batteries are plugged into their mating harness
leading to the charger.
Ensure both ends of the charger power cord are inserted fully.
Endeavor X
www.mega-motion.com
25
IV. BATTERIES AND CHARGING
How often must I charge the batteries?
Two major factors must be considered when deciding how often to charge your scooter’s batteries:
All day scooter use on a daily basis.
Infrequent or sporadic scooter use.
With these considerations in mind, you can determine how often and for how long you should charge your
scooter’s batteries. We designed the off-board charger so that it will not overcharge your scooter’s
batteries. However, you may encounter some problems if you do not charge your batteries often enough
and if you do not charge them on a regular basis. Following the guidelines below will provide safe and
reliable battery operation and charging.
If you use your scooter daily, charge its batteries as soon as you finish using it for the day. Your scooter
will be ready each morning. We recommend that you charge your scooter’s batteries for 8 to 14 hours
after daily use.
If you use your scooter once a week or less, charge its batteries at least once a week for 12 to 14 hours
at a time.
Keep your scooter’s batteries fully charged.
Avoid deeply discharging your scooter’s batteries.
How can I ensure maximum battery life?
Fully charged deep-cycle batteries provide reliable performance and extended battery life. Keep your
scooter’s batteries fully charged whenever possible. Protect your scooter and batteries from extreme heat
or cold. Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme
temperatures, or stored without a full charge may be permanently damaged, causing unreliable
performance and limited service life.
How can I get maximum range or distance per charge?
Rarely will you have ideal driving conditions—smooth, flat, hard driving surfaces with no wind or curves.
Often, you will face hills, pavement cracks, uneven and loosely packed surfaces, curves, and wind, all of
which affect the distance or running time per battery charge. Below are a few suggestions for obtaining
the maximum range per battery charge.
Always fully charge your scooter’s batteries prior to daily use.
Maintain but do not exceed the psi/bar/kPa air pressure rating indicated on pneumatic tires.
Plan your route ahead to avoid as many hills, cracked, broken or soft surfaces as possible.
Limit your baggage weight to essential items.
Try to maintain an even speed while your scooter is in motion.
Avoid stop-and-go driving.
What type and size of battery should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. Both AGM and Gel-Cell are
deep-cycle batteries that are similar in performance. Do not use wet-cell batteries, which have removable
caps.
WARNING! Corrosive chemicals are contained in batteries. Use only AGM or GelCell batteries to reduce the risk of leakage or explosive conditions.
NOTE: Sealed batteries are not serviceable. Do not remove the caps.
26
www.mega-motion.com
Endeavor X
IV. BATTERIES AND CHARGING
How do I change a battery in my scooter?
MANDATORY! Battery posts, terminals, and related accessories contain lead
and lead compounds. Wear goggles and gloves when handling batteries and
wash hands after handling.
WARNING! Always use two batteries of the exact same type, chemistry, and
amp-hour (Ah) capacity. Refer to the specifications table in this manual and in
the manual supplied with the battery charger for recommended type and
capacities.
WARNING! Contact your authorized Mega Motion Provider if you have any
questions regarding the batteries in your scooter.
WARNING! Do not replace the batteries while the scooter is occupied.
WARNING! Do not mix old and new batteries. Always replace both batteries at
the same time.
WARNING! The batteries on your scooter should only be serviced or replaced by
an authorized Mega Motion Provider or a qualified technician.
PROHIBITED! Keep tools and other metal objects away from battery terminals.
Contact with tools can cause electrical shock.
You may need the following to change your batteries:
Metric/standard socket set and ratchet
Adjustable wrench
To change the batteries in your scooter:
WARNING! Do not lift beyond your physical capability. Ask for assistance when
necessary while disassembling or assembling your scooter.
1.
2.
3.
4.
5.
6.
7.
Remove the seat and rear shroud. See VII. “Disassembly and Assembly.”
Disconnect the battery tie-down strap.
Disconnect the battery harnesses by pulling them straight up. See figure 13.
Disconnect the battery cables from the battery terminals.
Remove the old batteries.
Place a new battery in each battery well. Face the battery terminals toward the seat post.
Connect the red battery cable to the positive (+)
battery terminal. See figure 13A.
TERMINAL BOOTS
8. Connect the black battery cable to the
BATTERY HARNESSES
negative (-) battery terminal.
9. Ensure the battery terminals are covered with
the tiller boots.
NOTE: See figure 13B for correct hardware
placement for battery terminal connections.
10. Reconnect the battery harnesses.
11. Reconnect the battery tie-down strap, making
sure the strap is positioned over the frame
release lever to ensure proper securement. See
figure 13C.
12. Reinstall the rear shroud and seat.
Figure 13. Battery Harnesses and Battery Cables
Endeavor X
www.mega-motion.com
27
IV. BATTERIES AND CHARGING
NOTE: If you encounter a damaged or cracked battery,
immediately enclose it in a plastic bag and contact your
local waste disposal agency or authorized Mega Motion
Provider for instructions on disposal and battery
recycling which is our recommended course of action.
Why do my new batteries seem weak?
Deep-cycle batteries employ a different chemical
technology than that used in car batteries, nickel-cadmium
batteries (nicads), and other common battery types. Deepcycle batteries are specifically designed to provide power,
drain down their charge, and then accept a relatively quick
recharge.
We work closely with our battery manufacturer to provide
batteries that best suit your scooter’s specific electrical
demands. Fresh batteries are shipped fully charged to our
customers. During shipping, the batteries may encounter
temperature extremes that can influence their initial
performance. Heat diminishes the charge on the battery;
cold slows the available power and extends the time
needed to recharge the battery.
Figure 13A. Battery Cable Orientation
Figure 13B. Cable To Terminal Connection
It may take a few days for the temperature of your scooter’s
batteries to stabilize and adjust to their new room or ambient
temperature. More importantly, it takes a few charging
cycles (partial draining followed by full recharging) to
establish the critical chemical balance that is essential to a
deep-cycle battery’s peak performance and long life.
BATTERY TIE-DOWN STRAP
Follow these steps to properly break in your scooter’s
Figure 13C. Battery Tie-down Strap
new batteries for maximum efficiency and service life:
1. Fully recharge any new battery prior to its initial use.
This charging cycle brings the battery up to about 88% of its peak performance level.
2. Operate your new scooter in familiar and safe areas. Drive slowly at first, and do not travel too far from
your home or familiar surroundings until you have become accustomed to your scooter’s controls and
have properly broken in your scooter’s batteries.
3. Fully recharge the batteries. They should be at over 90% of their peak performance level.
4. Operate your scooter again.
5. Fully recharge the batteries again.
6. After four or five charging cycles, the batteries are able to receive a charge of 100% of their peak
performance level and are able to last for an extended period of time.
What about public transportation?
If you intend to use public transportation with your scooter, you must contact the transportation provider
in advance to determine their specific requirements.
28
www.mega-motion.com
Endeavor X
V. OPERATION
BEFORE GETTING ONTO YOUR SCOOTER
Have you fully charged the batteries? See IV. “Batteries and Charging.”
Is the manual freewheel lever in the drive (rearward) position? Never leave the manual freewheel lever
pushed forward unless you are manually pushing your scooter.
Is the tiller lock knob in the unlocked position? See VII. “Disassembly and Assembly.”
GETTING ONTO YOUR SCOOTER
1. Make certain that the key is removed from the key switch.
WARNING! Never attempt to get onto or off of your scooter without first removing the key
from the key switch. This will prevent the scooter from moving if accidental throttle
control lever contact is made.
2.
3.
4.
5.
6.
7.
8.
Stand at the side of your scooter.
Disengage the seat rotation lever and rotate the seat until it is facing you.
Make certain that the seat is fixed securely in position.
Position yourself comfortably and securely in the seat.
Disengage the seat rotation lever and rotate the seat until you are facing forward.
Make certain that the seat is fixed securely in position.
Make certain that your feet are safely on the floorboard.
PRE-RIDE ADJUSTMENTS AND CHECKS
Is the seat at the proper height? See VI. “Comfort Adjustments.”
Is the seat fixed securely in place?
Is the tiller at a comfortable setting and locked securely in place? See VI. “Comfort Adjustments.”
Is the key fully inserted into the key switch and turned clockwise to the “on” position?
Does the scooter’s horn work properly?
Is your proposed path clear of people, pets, and obstacles?
Have you planned your route to avoid adverse terrain and as many inclines as possible?
OPERATING YOUR SCOOTER
WARNING! The following can adversely affect steering and stability while operating your
scooter, resulting in loss of control or tipping:
Holding onto or attaching a leash to walk your pet
Carrying passengers (including pets)
Hanging any article from the tiller
Towing or being pushed by another motorized vehicle
WARNING! Higher Rollover Risk! Avoid abrupt maneuvers at excessive speed. It is
recommended that you set the speed adjustment dial to the lowest setting until you
become familiar with scooter controls and operation.
WARNING! Scooter braking distances are greater on an incline than on the horizontal.
WARNING! Keep both hands on the tiller and your feet on the floorboard at all times while
operating your scooter. This driving position gives you the most control over your
vehicle.
Set the speed adjustment dial to your desired speed.
Push or pull the appropriate side of the throttle control lever.
Endeavor X
www.mega-motion.com
29
V. OPERATION
The electromechanical disc park brake automatically disengages and the scooter accelerates smoothly
to the speed you preselected with the speed adjustment dial.
Pull on the left handgrip to steer your scooter to the left.
Pull on the right handgrip to steer your scooter to the right.
Move the tiller to the center position to drive straight ahead.
To stop, slowly release the throttle control lever. The electronic brakes will automatically engage,
bringing your scooter to a stop.
NOTE: Your scooter’s reverse speed is slower than that of the forward speed you preset with the speed
adjustment dial.
GETTING OFF YOUR SCOOTER
1. Bring your scooter to a complete stop.
2. Remove the key from the key switch.
3. Disengage the seat rotation lever and rotate the seat until you are facing toward the side of your scooter.
4. Make certain that the seat is fixed securely in position.
5. Carefully and safely get out of the seat and stand to the side of your scooter.
6. You can leave the seat facing to the side to facilitate boarding your scooter next time.
POWER DOWN TIMER FEATURE
Your scooter is equipped with an energy saving automatic power down timer feature designed to preserve
your scooter’s battery life. If you mistakenly leave the key in the key switch and in the “on” position but
do not use your scooter for approximately 20 minutes, the scooter’s controller shuts down automatically.
Although the controller is shut down, power will still be supplied to the scooter’s lighting system.
If the power down timer feature takes effect, perform the following steps to resume normal operation.
1. Remove the key from the key switch.
2. Reinsert the key and power up your scooter.
30
www.mega-motion.com
Endeavor X
VI. COMFORT ADJUSTMENTS
TILLER ANGLE ADJUSTMENT
Your scooter is equipped with an adjustable tiller.
TILLER ADJUSTMENT LEVER
WARNING! Remove the key from the
key switch before adjusting the tiller
or the seat. Never attempt to adjust
the tiller or the seat while the scooter
is in motion.
To change the tiller angle:
1. Squeeze the tiller adjustment lever. See figure 14.
2. Move the tiller to a comfortable position.
3. Release the tiller adjustment lever to lock the tiller
into place.
NOTE: In order to fully lower the tiller, you must first
remove the seat. Remove the seat by pushing the seat
rotation lever forward, slightly rotating the seat, then
lifting the seat straight up.
TILLER CONSOLE ADJUSTMENT DIAL
Figure 14. Tiller/Tiller Console Adjustment
TILLER CONSOLE ANGLE ADJUSTMENT
The tiller console can be adjusted to different angles.
ADJUSTMENT DIAL
To change the console angle:
1. Loosen the adjustment dial (turn counterclockwise)
and move the tiller console up or down to a
comfortable riding position. See figure 14.
2. Hold the console at that position and tighten (turn
clockwise) the adjustment dial.
ARMREST ANGLE ADJUSTMENT
The armrest angle of your scooter can be adjusted
upward or downward by turning the adjustment dial.
See figure 15.
Figure 15. Armrest Angle Adjustment
NOTE: Pivot the armrests upward to make getting
onto and off of your scooter easier.
SEATBACK ADJUSTMENT
WARNING! Do not operate your scooter
with the seatback in a reclined
position.
WARNING! Always keep your back
pressed firmly against the seatback
while adjusting the angle.
SEATBACK
ADJUSTMENT
LEVER
Figure 16. Seatback Adjustment
Endeavor X
www.mega-motion.com
31
VI. COMFORT ADJUSTMENTS
To adjust your scooter’s reclining seat, perform
these steps. See figure 16.
1. With your back pressed up against the seatback,
lift up on the seatback adjustment lever and
lean forward or backward to adjust the seatback
angle.
2. Release the seatback adjustment lever once the
seat is in a comfortable riding position.
SEAT ROTATION ADJUSTMENT
The seat rotation lever will secure the seat into
several positions.
1. Push forward on the seat rotation lever to
disengage the seat. See figure 16A.
2. Rotate the seat to the desired position.
3. Release the lever to secure the seat into place.
FRONT-TO-BACK SEAT ADJUSTMENT
You can reposition the seat forward or backward to
adjust the distance between the seat and the tiller.
See figure 16A.
1. Move the seat sliding lever outward.
2. While holding the lever out, slide the seat forward or backward.
3. Release the seat sliding lever once the seat is in
the desired position.
SEAT ROTATION LEVER
BOLTS
SEAT SLIDING LEVER
Figure 16A. Seat Adjustment Levers
SEAT HEIGHT
ADJUSTMENT
NUT
UPPER SEAT
POST
LOCATING
HOLE
SEAT HEIGHT ADJUSTMENT
The seat can be repositioned to different heights.
SEAT HEIGHT
See figure 17.
ADJUSTMENT
1. Remove the seat and shroud from your scooter.
BOLT
See VII. “Disassembly and Assembly.”
CLAMP-ACTION
2. Loosen the seat height adjustment nut and
NUT
remove it from the bolt. Remove the bolt and
CLAMP-ACTION
washers.
BOLT
3. Loosen the clamp-action bolt.
4. Raise or lower the upper seat post to the desired
LOWER SEAT POST
seat height.
Figure 17. Seat Height Adjustment
5. While holding the upper seat post at that height,
match up the locating holes in the upper seat post with those of the lower seat post.
6. With one washer on the seat height adjustment bolt, insert it through the locating holes of both the
upper and lower seat posts.
7. Reinstall the other washer and nut and tighten.
NOTE: Ensure both washers have been reinstalled before fully tightening the seat height adjustment nut.
8. Tighten the clamp-action bolt.
9. Reinstall the rear shroud and the seat.
32
www.mega-motion.com
Endeavor X
VI. COMFORT ADJUSTMENTS
MIRROR POSITION
To install the mirror (see figure 18):
1. Determine a side to install the mirror and remove the
rubber plug from the top of the tiller handle.
2. Insert the threaded end of the mirror holder into the
opening and rotate it clockwise until snug.
3. If necessary, rotate the nut clockwise to secure the
mirror in place.
MIRROR HOLDER
PLUG
NUT
To adjust the mirror:
1. Position yourself in a seated driving position facing
forward.
2. Adjust the mirror left, right, up or down until you have
a good line of sight behind you.
Figure 18. Mirror Installation
POSITIONING BELT (OPTIONAL)
Your scooter seat may be equipped with an auto-type positioning belt that can be adjusted for operator
comfort. See figure 19. The positioning belt is designed to help support the operator so that he/she does
not slide down or forward in the seat. The positioning belt is not designed for use as a restraining device.
WARNING! The positioning belt should be secured at all times. Never allow the
positioning belt to hang or drag on the floor as it may become entangled.
To install the positioning belt (if required):
1. Remove the seat from your scooter.
2. Place the seat upside down so that you can see the bottom of the seat base.
3. Remove the two bolts on the outermost part of the rear seat mounting strap. See figure 16A.
4. Insert the bolt through the appropriate end of the positioning belt and then through the seat mounting
strap for each side of the scooter seat.
5. Tighten the bolts.
To adjust the positioning belt for operator comfort:
1. Insert the metal tab on the right side of the belt into the plastic housing on the opposite strap until you
hear a “click.”
2. Pull the strap on the right side of the belt until it is secure, but not so tight as to cause discomfort.
To release the positioning belt:
1. Press the push button mechanism on the plastic housing.
MANDATORY! Make sure the positioning
belt is properly secured to the scooter and
is adjusted for operator comfort.
MANDATORY! Inspect the positioning belt
for loose or damaged parts before each
use of the scooter. If you discover a
problem, contact your authorized Mega
Motion Provider for maintenance and
repair.
Figure 19. Positioning Belt
Endeavor X
www.mega-motion.com
33
VII. DISASSEMBLY AND ASSEMBLY
DISASSEMBLY
You can disassemble the scooter into several
pieces: the seat, the front section, the rear section,
the rear shroud, the basket, and the batteries. See
figure 20. No tools are required to disassemble or
assemble your scooter, but keep in mind that the
disassembled sections of the scooter take up more
floor space than the assembled unit. Always
disassemble or assemble your scooter on a level,
dry surface with sufficient room for you to work
and move around your scooter—about 2 meters
(6 feet) in all directions. Remember that some
scooter components are heavy and you may need
assistance when lifting them.
WARNING! Do not lift beyond your
physical
capability.
Ask
for
assistance when necessary while
disassembling or assembling your
scooter.
BASKET
REAR SECTION
SEAT
BATTERIES
REAR SHROUD
FRONT SECTION
Figure 20. The Scooter Disassembled
1. Place the scooter in drive mode by engaging the freewheel lever.
2. Lock the tiller in the straight ahead position by pushing the tiller lock knob in and turning it clockwise
90°. See figure 21. The front wheel must face forward in order to lock the tiller.
3. Remove the seat by lifting it straight up and off of the scooter. If you encounter resistance when
removing the seat, disengage the seat rotation lever and swivel the seat back and forth while lifting up
on the seat.
4. Gently pull the rear shroud up and off of the rear section of the scooter.
5. Unplug the front-to-rear and rear lighting harnesses by squeezing the sides and pulling straight up.
6. Unplug both battery harnesses. Pull each harness straight up. See figure 23.
WARNING! Failure to unplug both battery harnesses, the front-to-rear harness, and rear
lighting harness prior to separating the front and rear sections could result in permanent
damage to the scooter.
LOCKED
POSITION
Figure 21. Tiller Lock knob (Locked)
34
UNLOCKED
POSITION
Figure 22. Tiller Lock Knob (Unlocked)
www.mega-motion.com
Endeavor X
VII. DISASSEMBLY AND ASSEMBLY
7. Unfasten the battery tie-down straps and remove
the batteries from the battery wells.
8. Squeeze the tiller adjustment lever and lower
the tiller to its lowest point. Adjust the tiller
console if necessary.
REAR LIGHTING
HARNESS
WARNING! Failure to unplug both
battery harnesses, the front-to-rear
harness, and rear lighting harness
prior to separating the front and
rear sections could result in
permanent damage to the scooter.
Frame Separation
1. Lift up on the frame release lever. See figure 24.
2. Lift the front section up until the frame hooks
of the front section separate from the rear
section. See figure 24.
NOTE: Stabilize the rear section with your free
hand by holding onto the upper frame tube. See
figure 25.
BATTERY HARNESSES
FRONT-TO REAR HARNESS
Figure 23. Harness Connections
FRAME RELEASE LEVER
3. Slowly separate the two sections. See figure 25.
ASSEMBLY
1. Position the front and rear sections of your
scooter as shown in figure 24.
2. Use the frame release lever to lift the front
section as you align the frame hooks of the front
section with the lower frame tube of the rear
section. See figure 24.
3. Once the frame hooks are over the lower frame
tube, lower the front section completely. This
will engage the frame lock.
4. Raise the tiller.
5. Reinstall both batteries and secure with the
battery tie-down strap, making sure the strap is
positioned over the frame release lever to
ensure proper securement.
6. Connect the front-to-rear harness, rear lighting
harness, and both battery harnesses. See figure 23.
7. Reinstall the rear shroud.
8. Reinstall the seat and rotate it into place.
9. Unlock the front wheel by turning the tiller lock
knob 90° counterclockwise. See figure 22.
WARNING! After assembly, make
absolutely certain the tiller lock
knob is in the unlocked position
before riding your scooter.
Endeavor X
FRAME HOOK
Figure 24. Frame Release
LOWER FRAME TUBE
UPPER FRAME TUBE
FRAME HOOK
Figure 25. Frame Separation
www.mega-motion.com
35
VIII. BASIC TROUBLESHOOTING
Any electromechanical device occasionally requires some troubleshooting. However, most of the
problems that may arise can usually be solved with a bit of thought and common sense. Many of these
problems occur because the batteries are not fully charged or because the batteries are worn down and can
no longer hold a charge.
DIAGNOSTIC FAULT CODES
The diagnostic fault codes for your scooter are designed to help you perform basic troubleshooting quickly
and easily. The scooter will either display a diagnostic flash code or emit a beep code in the event one of
the conditions listed below develops.
NOTE: Your scooter will not run unless the fault code condition is resolved and the scooter has been
turned off, then turned back on.
FAULT CODE
(1,1)
(1,4)
(3,3)
(1,2)
(1,3)
(1,5)
(3,5)
(3,4)
(3,2)
CONDITION
SOLUTION
Controller is hot; the scooter seems to
be losing power.
Shut down your scooter for a minimum
of several minutes to allow the
controller to cool.
Battery charge is low.
Charge batteries as soon as possible.
Throttle pot fault
Contact your authorized Mega Motion
Provider for assistance.
Speed pot fault
Contact your authorized Mega Motion
Provider for assistance.
Turn the scooter key to the off position.
Switch off the charger and remove the
cord from the charger port, then restart
your scooter.
Attempting to operate the scooter with
the charger attached.
Throttle control lever not at center
position at start up.
Return the throttle control lever to the
center position, turn scooter off, and
then back on.
The manual freewheel lever may be in
the freewheel (forward) position.
Turn the scooter key to the off position.
Push the freewheel lever to the drive
(backward) position, then restart your
scooter.
A brake fault has occurred.
Contact your authorized Mega Motion
Provider for assistance.
What if all the systems on my scooter seem to be “dead”?
Make certain that the key is in the “on” position.
Check that the batteries are fully charged.
Push in the main circuit breaker reset button. See III. “Your Scooter.”
Make certain that both battery harnesses and the front-to-rear harness are firmly connected. See VII.
“Disassembly and Assembly.”
Be sure the power down timer feature has not been activated. See V. “Operation.”
36
www.mega-motion.com
Endeavor X
VIII. BASIC TROUBLESHOOTING
What if my scooter does not move when I engage the throttle control lever?
When the manual freewheel lever is pushed forward, the brakes are disengaged and all power to the
motor/transaxle assembly is cut.
Pull back on the manual freewheel lever, turn the scooter off and then turn the scooter on to return to
normal scooter operation.
What if the main circuit breaker repeatedly trips?
Charge the scooter’s batteries more frequently. See IV. “Batteries and Charging.”
If the problem continues, have both of your scooter’s batteries load tested by your authorized Mega
Motion Provider.
If the main circuit breaker trips repeatedly, contact your authorized Mega Motion Provider for service.
You may also perform the load test yourself. Battery load testers are available at most automotive parts
stores. Follow the directions supplied with the load tester.
See IV. “Batteries and Charging” or “Appendix I - Specifications” for information about your
scooter’s battery type.
What if the battery condition meter dips way down and the motor surges or hesitates when I engage
the throttle control lever?
Fully charge your scooter’s batteries. See IV. “Batteries and Charging.”
Have your authorized Mega Motion Provider load test each battery.
Or, see the previous troubleshooting question for load testing the batteries yourself.
If you experience any problems with your scooter that you are not able to solve, immediately contact your
authorized Mega Motion Provider for information, maintenance, and service.
Endeavor X
www.mega-motion.com
37
IX. CARE AND MAINTENANCE
Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your
ability to perform the maintenance listed below, you may schedule inspection and maintenance at your
authorized Mega Motion Provider. The following areas require periodic inspection and/or care and
maintenance.
TIRE PRESSURE
If equipped with pneumatic tires, always maintain the psi/bar/kPa air pressure indicated on each tire.
WARNING! It is important that the psi/bar/kPa air pressure indicated on each tire be
maintained in pneumatic tires at all times. Do not underinflate or overinflate your tires.
Low pressure may result in loss of control, and overinflated tires may burst. Failure to
maintain the psi/bar/kPa air pressure indicated on pneumatic tires at all times may result
in tire and/or wheel failure.
Regularly inspect your scooter’s tires for signs of wear.
EXTERIOR SURFACES
Bumpers, tires, and trim can benefit from an occasional application of rubber or vinyl conditioner.
WARNING! Do not use a rubber or vinyl conditioner on the scooter’s vinyl seat or tire
tread, as this may cause them to become dangerously slippery.
CLEANING AND DISINFECTION
Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your scooter.
Avoid using products that may scratch the surface of your scooter.
If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for
use on your product before application.
WARNING! Follow all safety instructions for the proper use of the disinfectant and/or
cleaning agent before applying it to your product. Failure to comply may result in skin
irritation or premature deterioration of upholstery and/or scooter finishes.
BATTERY TERMINAL CONNECTIONS
Make certain that the terminal connections remain tight and uncorroded.
The batteries must sit flat in the battery wells.
WIRING HARNESSES
Regularly check all wiring connections.
Regularly check all wiring insulation, including the charger power cord, for wear or damage.
Have your authorized Mega Motion Provider repair or replace any damaged connector, connection, or
insulation that you find before using your scooter again.
PROHIBITED! Even though the scooter has passed the necessary testing requirements
for ingress of liquids, you should keep electrical connections away from sources of
dampness, including direct exposure to water or bodily fluids and incontinence. Check
electrical components frequently for signs of corrosion and replace as necessary.
WARNING! Do not pull on electrical harnesses directly to detach them from the scooter.
Always grasp the connector itself when disconnecting the harness to prevent wire
damage.
38
www.mega-motion.com
Endeavor X
XI. CARE AND MAINTENANCE
AXLE BEARINGS AND THE MOTOR/
TRANSAXLE ASSEMBLY
You do not need to lubricate these items, as they are
all prelubricated and sealed.
DRIVE WHEEL WASHER
AXLE KEY
MOTOR BRUSHES
The motor brushes are housed inside of the motor
transaxle/assembly. They should be inspected
periodically for wear by your authorized Mega
Motion Provider.
WHEEL REPLACEMENT
If your scooter is equipped with pneumatic tires and
you have a flat tire, you can have the tube replaced.
If your scooter is equipped with a solid tire insert,
either the solid insert or the entire wheel must be
replaced depending on the model. Contact your
authorized Mega Motion Provider for information
regarding replacement wheels for your scooter.
WARNING! Wheels on your scooter
should only be serviced/replaced by
an authorized Mega Motion Provider
or qualified technician.
AXLE SLOT
DRIVE WHEEL NUT
Figure 26. Solid Tire Wheel Removal
HUB
REAR RIM HALF
WARNING!
COMPLETELY
DEFLATE THE TIRE BEFORE
ATTEMPTING REPAIR!
WARNING!
Completely
deflate
pneumatic tires before dismantling
the rim or attempting repair.
TIRE
WARNING! Be sure that the key is
removed from the key switch and the
scooter is not in freewheel mode
before performing this procedure.
WARNING! When changing a tire,
remove only the center lug nut, then
remove the wheel. If any further
disassembly is required, deflate the
tire completely or it may explode.
TUBE
FRONT RIM HALF
WASHERS
NUTS
Follow these easy steps for a quick and safe
Figure 27. Drive Wheel Assembly
repair of both pneumatic and solid tires:
1. Remove the key from the key switch.
2. Elevate the side of the scooter from which you
are removing the tire. Place wooden blocks under the frame to elevate the scooter.
3. If you are changing a pneumatic tire, completely deflate it before removing the wheel.
4. Remove the drive wheel nut and washer from the axle. See figure 26.
5. Pull the wheel off the axle.
6. Remove the nuts and washers and separate the rim halves. See figure 27.
7. Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire
assembly if it is a solid tire.
8. Reassemble the rim halves.
9. Slide the wheel back onto the axle. Make sure that the axle key is in the axle slot. See figure 26.
Endeavor X
www.mega-motion.com
39
IX. CARE AND MAINTENANCE
WARNING! Failure to ensure that the axle key is properly installed into the axle
slot when mounting the wheel can result in electronic brake failure and/or
product damage.
10. Reinstall the drive wheel nut and washer onto the axle and tighten.
WARNING! Make sure both the nut and washer are reinstalled and tightened properly.
11. Inflate pneumatic tires to the psi/bar/kPa air pressure rating indicated on each tire.
12. Remove the blocks from beneath the scooter.
CONSOLE, CHARGER, AND ELECTRONIC CONTROLLER MODULE
Keep these areas away from moisture.
Before operating your scooter, allow any of these areas to dry thoroughly if they have been exposed to
moisture.
ABS PLASTIC SHROUDS
The front tiller shroud, front shroud, and the rear shroud are formed from durable ABS plastic and are
coated with an advanced formula urethane paint.
A light application of car wax will help the shrouds retain their high gloss.
FUSE REPLACEMENT
To replace a fuse:
1. Remove the fuse by pulling it straight out of its slot.
2. Examine the fuse to be sure it is blown. See figures 28 and 29.
3. Insert a new fuse of the proper rating.
WARNING! The replacement fuse must exactly match the rating of the fuse being
replaced. Failure to use properly rated fuses may cause damage to the electrical system.
Figure 28. Working Fuse
Figure 29. Blown Fuse (Replace)
NYLON LOCK NUT REPLACEMENT
Any nylon insert lock nut removed during the periodic maintenance, assembly, or disassembly of the
scooter must be replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause
damage to the nylon insert, resulting in a less secure fit. Replacement nylon insert lock nuts are available
at local hardware stores or through your authorized Mega Motion Provider.
40
www.mega-motion.com
Endeavor X
IX. CARE AND MAINTENANCE
STORING YOUR SCOOTER
If you plan on not using your scooter for an extended period of time, it is best to:
1. Fully charge its batteries prior to storage.
2. Disconnect the batteries from the scooter.
3. Store your scooter in a warm, dry environment.
4. Avoid storing your scooter where it will be exposed to temperature extremes.
WARNING! Always protect batteries from freezing temperatures and never charge a
frozen battery. Charging a frozen battery can result in damage to the battery.
Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures,
or stored without a full charge may be permanently damaged, causing unreliable performance and limited
service life. It is recommended that you charge the scooter batteries periodically throughout periods of
prolonged storage to ensure proper performance.
You may wish to place several boards under the frame of your scooter to raise it off of the ground during
periods of prolonged storage. This takes the weight off the tires and reduces the possibility of flat spots
developing on the areas of the tires contacting the ground.
DISPOSAL OF YOUR SCOOTER
Your scooter must be disposed of according to applicable local and national statutory regulations. Contact
your local waste disposal agency or authorized Mega Motion Provider for information on proper disposal
of packaging, metal frame components, plastic components, electronics, batteries, neoprene, silicone, and
polyurethane materials.
Endeavor X
www.mega-motion.com
41
X. WARRANTY
90-DAY LIMITED WARRANTY
For 90 days from the date of purchase, Mega Motion will repair or replace at our option to the original
purchaser, free of charge, any of the following parts found upon examination by an authorized representative of Mega Motion to be defective in material and/or workmanship:
Structural frame components, including:
Main Frame
Fork
Tiller Frame
Bearings
Rubber Components
Plastic components except body
Seat Post
Bushings
Also, electronic assemblies including:
Electronic Controllers
Any other electrical subassembly
Harnesses
Chargers
SIX-MONTH WARRANTY
The battery is covered by a separate six-month warranty, provided by the battery manufacturer. The batteries are not warranted by Mega Motion.
WARRANTY EXCLUSIONS
This warranty does not extend to those items which may require replacement due to normal wear and tear.
ABS Plastic shrouds
Motor brushes
Upholstery and seating
Brake Pads
Solid Tires
Fuses/Bulbs
Circumstances beyond the control of Mega Motion
Labor, service calls, shipping, and other charges incurred for repair of the product, unless specifically
authorized, IN ADVANCE, by Mega Motion
Repairs and/or modifications made to any part without specific consent from Mega Motion
Exclusions also include components with damage caused by:
Contamination
Abuse, misuse, accident, or negligence
Battery fluid spillage or leakage
Commercial use, or use other than normal
Improper operation, maintenance, or storage
Batteries not properly maintained by recommended charging and storage procedures.
SERVICE CHECKS AND WARRANTY SERVICE
Warranty service must be performed by Mega Motion. Do not return faulty parts to Mega Motion without
prior written authorization. All transportation costs and shipping damage incurred while submitting parts
for repair or replacement are the responsibility of the purchaser. Please contact 1-800-MEGA-508 for
information on the current cost associated with a service visit.
There is no other express warranty.
42
www.mega-motion.com
Endeavor X
X. WARRANTY
IMPLIED WARRANTIES
Implied warranties, including those of merchantability and fitness for a particular purpose, are
limited to one (1) year from the date of original purchase and to the extent permitted by law. Any
and all implied warranties are excluded. This is the exclusive remedy. Liabilities for consequential damages under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion
or limitation of incidental or consequential damages. So, the above limitation or exclusion may not apply
to you.
Endeavor X
www.mega-motion.com
43
APPENDIX I - SPECIFICATIONS
ENDEAVOR X SPECIFICATIONS
Model Numbers
3-wheel: MM4001DX; 4-wheel: MM4401DX
Maximum Allowable Incline
3-wheel: 5º (8.7%); 4-wheel: 6º (10.5%)
Maximum Angle Capacity
10º (17.6%)
Maximum Climbing Ability
2 in. (5 cm)
Overall Length 3
3-wheel: 46 in. (116.84 cm); 4-wheel: 46.62 in. (118.75 cm)
Overall Width 3
24 in. (61cm)
Total Weight Without Batteries
3-wheel: 155 lbs. (70.3 kg); 4-wheel: 171.5 lbs. (77.8 kg)
Heaviest Piece When Disassembled
Front section:
3-wheel: 59.5 lbs. (27 kg); 4-wheel: 69 lbs. (31.3 kg)
Turning Radius 3
3-wheel: 41.5 in. (105.41 cm); 4-wheel: 54 in. (137.16 cm)
Speed (Maximum) 1
Up to 5.7 mph (9.17 km/h)
Range Per Charge 1, 2
Up to 10.85 miles (17.5 km) with U-1 batteries
Ground Clearance
4 in. (10.16 cm) at deck
Weight Capacity
350 lbs. (158 kg)
Standard Seating Type
CRS Deluxe
Weight: 49 lbs. (22.2 kg)
Material: Vinyl
Dimensions: 18 in. (45.72 cm) width
18 in. (45.72 cm) depth
Drive System
Rear-wheel drive, sealed transaxle, 24 volt DC motor
Tires
Type: Solid
Front: 3.5 in. x 10 in. (8.89 cm x 25.4 cm)
Rear: 4 in. x 13 in. (10.16 cm x 25.4 cm)
Battery Requirements 4, 5
Two 12-volt, deep-cycle
Size: U-1 (40 Ah optional)
Weight: (U-1) 24.5 lbs. (11.11 kg) / (40Ah) 32.5 lbs. (14.75 kg)
Battery Charger
Off-board
1
2
3
4
5
Varies with user weight, terrain type, battery amp-hour (Ah), battery charge, battery condition, and tire
condition. This specification can be subject to a variance of +10%, -5%.
Tested in accordance with ANSI/RESNA, WC Vol 2, Section 4 & ISO 7176-4 standards. Results derived from
theoretical calculation based on battery specifications and drive system performance. Test conducted at maximum
weight capacity.
Due to manufacturing tolerances and continual product improvement, this specification can be subject to a
variance of (+ or -) 3 %.
AGM or Gel-Cell type required. See IV. “Batteries and Charging.”
Battery weight may vary based on battery manufacturer.
NOTE: This product conforms to all applicable ANSI-RESNA testing requirements and ISO 7176
series EN12184 standards. All specifications subject to change without notice.
44
www.mega-motion.com
Endeavor X
APPENDIX I - SPECIFICATIONS
3-wheel: 46" (116.84 cm)
4-wheel: 46.62" (118.75 cm)
18"
(45.72 cm)
18"
(45.72 cm)
3-wheel Turning Radius
4-wheel Turning Radius
41.5" (105.41 cm)
54" (137.16 cm)
24" (61 cm)
29" (73.66 cm)
4" (10.16 cm)
Figure 30. Scooter Dimensions and Ground Clearance
Endeavor X
www.mega-motion.com
45
NOTES
46
www.mega-motion.com
Endeavor X
Owner’s Manual
Mega Motion Inc.
P.O. Box 275
Taylor, PA 18517-0275
1-800-MEGA-508
*INFMANU4333*
Mega Motion, Inc.
P.O. Box 275
Taylor, PA 18517-0275
www.mega-motion.com