SECTION 16 Gate Operators - Jansen Ornamental Supply Co.

SECTION 16
Gate Operators
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-1
High-Traffic Commercial DC Sliding Gate Operator
with Battery Back-Up. ELITE Series
LiftMaster® Elite® Series Model CSL24V is engineered for a million cycles in high-cycle
heavy-duty applications and is rated for gates up to 50 feet or 1500 lbs.
CSL24V
HIGH TRAFFIC COMMERCIAL
110V Power / 24VDC 500mA Output
50 ft Gate - 1500 lbs. - Continuous Duty
Battery Back-up - 100 Cycles on 2- 7Ah
5 yr. Com. - 7 yr. Res. Warranty
Chain #41 - 30 ft.
25” H. X 14.82” W. X 23” D.
Battery Backup
Operator Wt. 140 lbs.
* Uninterrupted access when the power
is out.
Optional Solar Kit Available:
Security+ 2.0™ Technology
LM33AH24VSLRPKG - Comes with 2 - 20 Watt
* 2X the range of standard remotes.
panels, 2 - 33Ah batteries & harness.
LMA12330SGLPK - Replacement Battery 33 Ah
with harness for solar kit.
MyQ™ Technology Provides
BATTERY
CYCLES
2 - 7Ah
100
2 - 33Ah
380
16 ft / 1000 lbs.
Slide Gate
* Wireless dual gate communication.
* The ability to remotely monitor and
activate your gate from anywhere in
the world via internet or smart phone.
MYQ™ Enabled Accessories
LiftMaster Internet Gateway
Model 828LM
LiftMaster’s revolutionary new
accessory features built-in
MyQ™ technoloy that connects
to the internet and allows you to
monitor and operate your gate operator from
anywhere in world via your internet-enabled
computer or smart phone.
Garage and Gate Monitor
Model 829LM
Lets you check and close the
gate operator from any room in
your house.
Remote Light Control
Model 825LM
Control your house lights and operate any lamp with your remote control or from your Internet-enabled
smart phone via your LiftMaster
Internate Gateway™.
High-Traffic Commercial DC Swing Gate Operator
with Battery Back-Up. ELITE Series
LiftMaster® Elite® Series Model CSW24V is engineered for a million cycles in high-cycle
heavy-duty applications and is rated for gates up to 18 feet or 1200 lbs.
CSW24V
HIGH TRAFFIC COMMERCIAL
HIGH TRAFFIC COMMERCIAL
110V Power / 24VDC 500mA Output
18 ft Gate - 600 lbs. Continuous Duty
Battery Back-up - 100 Cycles on 2- 7Ah
5 yr. Com. - 7 yr. Res. Warranty
27.69” x 14.82” W. x 20” D.
Battery Backup
Operator Wt. 206 lbs.
Optional Solar Kit Available:
LM33AH24VSLRPKG - Comes with 2 - 20 Watt
panels, 2 - 33Ah batteries & harness.
LMA12330SGLPK - Replacement Battery 33 Ah
with harness for solar kit.
BATTERY
CYCLES
2 - 7Ah
100
2 - 33Ah
380
12 ft / 800 lbs.
Swing Gate
* Uninterrupted access when the power
is out.
Security+ 2.0™ Technology
* 2X the range of standard remotes.
MyQ™ Technology Provides
* Wireless dual gate communication.
* The ability to remotely monitor and
activate your gate from anywhere in
the world via internet or smart phone.
MYQ™ Enabled Accessories
LiftMaster Internet Gateway
Model 828LM
LiftMaster’s revolutionary new
accessory features built-in
MyQ™ technoloy that connects
to the internet and allows you to
monitor and operate your gate operator from
anywhere in world via your internet-enabled
computer or smart phone.
Garage and Gate Monitor
Model 829LM
Lets you check and close the
gate operator from any room in
your house.
Remote Light Control
Model 825LM
Control your house lights and operate any lamp with your remote control or from your Internet-enabled
smart phone via your LiftMaster
Internate Gateway™.
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-2
Residential / Light Commercial DC Swing Gate Operator
with Battery Back-Up.
LiftMaster® Model LA400 powerful 24VDC motor provides exceptional starting torque and features soft start / soft
stop operation. This promotes longer gate and operator life, as well as dependable performance. Rated for gates up
to 16 feet and weighing 550 lbs.
LA400
Residential / Light Commercial
24VDC 500mA Output
100 Cycles Per Day
8 ft. Gate - 850 lbs. / 12 ft. Gate - 750 lbs.
14 ft. Gate - 650 lbs. / 16 ft. Gate - 550 lbs.
Battery Back-up - 180 Cycles (base on 10 ft / 850 lb. gate)
2 Year Warranty
5.5” H. x 37.5” L. x 3.75” W.
Standard Control Box
14” H. x 10” W. x 6” D.
Models Available
LMLA4001PKG - LA400 Arm & Standard Control Box - 50 lbs.
LMLA400-S - Secondary Arm kit for the LA4001PKG - 25 lbs.
Replacement Battery: VIKBAT - 7Ah 12V Battery
Transformer: LMK74-30763 Transformer 12v
Out Swing Bracket: LM50-19503 Bracket kit for a OPEN-IN application.
On-Board Radio Receiver ~ DC Operator System
Battery-Run System ~ Slow Start /Stop
Timer To Close ~ LED Indicators
Electronic Limit System ~ Keyed Manual Disconnect
Residential / Light Commercial DC Swing Gate Operator
with Battery Back-Up. ELITE Series
LiftMaster® Elite® Series Model LA500 Operators are built to perform in the most demanding applications. The sturdy design is
powerful yet compact enough to fit where pad mount operators do not. Rated for gates up to 18 feet or 1200 lbs.
6” H. x 40” L.
LA500
Standard Control Box
16” H. X 13” W.
Extra Large Control Box
20” H. X 16” W.
Standard Box Shown
Residential / Light Commercial
110V Power / 24VDC 500mA Output
300 Cycles Per Day
8 ft. Gate - 1600 lbs. / 12 ft. Gate - 1200 lbs.
16 ft. Gate - 800 lbs. / 18 ft. Gate - 600 lbs.
Battery Back-up - 500 Cycles on 2 - 7Ah
5 yr. Com. - 7 yr. Res. Warranty
Models Available
LMLA5001PKG - LA500 Arm & Standard Control Box 45 lbs.
LMLA500-S - Secondary Arm kit for the LA5001PKG or
LA5001PKGXLM - 25 lbs.
LMLA5001PKGXLM - LA500 Arm & Extra Large Control
Box - 56 lbs.
LMLA500SLRPKG - Solar Package kit for
Battery Backup
* Uninterrupted access when the power
is out.
Security+ 2.0™ Technology
LMLA5001PKGXLM only. Package includes: 2 - 20W solar
panels, 2 - 33Ah batteries & harness. - 50 lbs.
* 2X the range of standard remotes.
Replacement Battery: LMA12330SGLPK - 33Ah 12V
MyQ™ Technology Provides
Battery with Harness for solar kit.
BATTERY
2 - 7Ah
2 - 33Ah
CYCLES
500
1800
12 ft / 800 lbs.
Swing Gate
* Wireless dual gate communication.
* The ability to remotely monitor and
activate your gate from anywhere in
the world via internet or smart phone.
MYQ™ Enabled Accessories
LiftMaster Internet Gateway
Model 828LM
LiftMaster’s revolutionary new
accessory features built-in
MyQ™ technoloy that connects
to the internet and allows you to
monitor and operate your gate operator from
anywhere in world via your internet-enabled
computer or smart phone.
Garage and Gate Monitor
Model 829LM
Lets you check and close the
gate operator from any room in
your house.
Remote Light Control
Model 825LM
Control your house lights and operate any lamp with your remote control or from your Internet-enabled
smart phone via your LiftMaster
Internate Gateway™.
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-3
Solar Powered Residential Gate Operator
CLASS I Vehicular Gate Operator
Solar powered operator with SMART technology utilizes innovative technology to deliver power when needed most for opening your
gate and minimizes power consumption at all other times for best solar performance DC motor provides soft start/soft stop operation.
This promotes longer gate and operator life, as well as dependable performance. Power is provided to the gate operator via batteries.
The batteries are charged from a solar panel(s) connected to the operator control board. The number of solar panels required is determined by whether the application is for a single or dual gate, daily cycle rate, number of accessories and region of the country.
LA412
LMLA4121PKG
Package Includes: Arm,
2 - 7Ah, 1 Solar Panel.
Wt. 46 lbs.
Residential Solar Powered System
Power: 12VDC
8 ft. Gate. - 850 lbs. / 12 ft. Gate - 750 lbs.
14 ft. Gate - 650 lbs. / 16 ft. Gate - 550 lbs.
UL325 Compliant
CLASS 1
Cycles Per Day (See Solar Cycle Chart Below)
Keyed Manual Disconnect
2 - 7Ah 12 Volt Batteries
2 Year Limited Factory Warranty
3.75 W. x 5.5” H. x 37.5” L.
LMLA412-S
Secondary Arm only
Wt. 20 lbs.
# LOOPDETSOLAR
Solar 12/24 V Loop Detector
Recommended for Exit or
Reverse loops installed
Replacement Battery: VIKBAT - 7Ah 12V Battery
Transformer to convert LA412 to a LA400 - LMLA12VXFMR
Out Swing Bracket: LM50-19503 Bracket kit for an OPEN-IN application.
LMSOLPNL10W12V
Extra Solar Panel
Wt. 8 lbs.
LA412 Solar Gate Access System Daily Cycle Chart
The map and daily cycle rate shown are approximations based upon the average solar
radiation and temperature effects on batteries in the given regions.
Zone 1
Zone 2
Zone 3
Single Arm Installation - Number of Cycles Per Day
10W Solar - 1 Panel
Arm Only
50 cycles
40 cycles
12 cycles
20W Solar - 2 Panel
Arm Only
50 cycles
50 cycles
28 cycles
30W Solar - 3 Panel
Arm Only
50 cycles
50 cycles
46 cycles
Dual Arm Installations - Number of Cycles Per Day
Number Identifies Zone. LA412 Not Support or Available in Zone 4
See Cycle Chart Above
10W Solar - 1 Panel
Arms Only
50 cycles
25 cycles
8 cycles
20W Solar - 2 Panel
Arms Only
50 cycles
50 cycles
20 cycles
30W Solar - 3 Panel
Arms Only
50 cycles
50 cycles
30 cycles
Cable From Solar Panel To
Control Box
Varies by number of solar panels, accessories or region
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-4
Commercial Grade
SL3000UL Sliding Gate Operator
Commercial Grade
SL3000ULE Sliding Gate Operator
1/2 HP ~ 1000 lbs
1/2 HP ~ 1000 lbs
ELITE S E R I E S
ELITE S E R I E S
The SL3000ULE have been specially designed to meet
fire marshal’s requirements for fire and emergency access.
In the event of power loss, the solenoid brake is automatically released, giving emergency personnel the ability to
push the gate open. When power is normal you still can
release the gate by a manual button on the operator.
The SL3000UL™ is recommended for high-traffic applications such as gated communities and commercial buildings.
Designed for smooth, exceptionally quiet performance, the
unit can handle continuous operation with gates weighing
up to 1,000 lbs. And up to 37 ft. in length with a raveling
speed of 12 inches per second.
Now with Security+ 2.0 Technology &
Model 850LM universal receiver installed.
Now with Security+ 2.0 Technology &
Model 850LM universal receiver installed.
The DC2000 (DCSL) provides uninterrupted
access during a power outage. Meets Fire
Marshalls requirements for Emergency
Access.
LMSL3000UL8
25” H. x 19” W. x 18” D.
EMERGENCY ACCESS
GATE OPERATOR
UL325
UL991
Compliant
25” H. x 19” W. x 18” D.
The DC2000 (DCSL) provides uninterrupted access during a power outage.
Meets Fire Marshalls requirements for
Emergency Access.
SL3000ULE
UL325
UL991
Compliant
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
1/2 HP - instant reversing, 1,625 rpm, high speed ball bearings
Duty Cycle
Continuous
Power Options
120 V AC, 4 amp
Cover
Molded Plastic - Weather Proof - Access Door
Fail Safe
No
Maximum Gate Length
37 Feet
Maximum Gate Weight
1/2 HP Motor: 1000 lbs.
Gate Speed
12 inches per sec.
Operator Weight
130 lbs.
Chain Size
#41 - 25 ft.
Emergency Release Options Manual Disconnect, Best option is our DC2000™ (DCSL)
Battery Backup Installed
No
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
1/2 HP - instant reversing, 1,625 rpm, high speed ball bearings
Duty Cycle
Continuous
Power Options
120 V AC, 4 amp
Cover
Molded Plastic - Weather Proof - Access Door
Fail Safe
Yes
Maximum Gate Length
37 Feet
Maximum Gate Weight
1/2 HP Motor: 1000 lbs.
Gate Speed
12 inches per sec.
Operator Weight
130 lbs.
Chain Size
#41 - 25 ft.
Emergency Release Options Pressed manual button once to disconnect, press again to reset.
Battery Backup Installed
No
Commercial Grade
SL3000UL1HP Sliding Gate Operator
Commercial Grade
SL3000UL1HPE Sliding Gate Operator
Specifications
ELITE S E R I E S
1 HP ~ 2000 lbs
1 HP ~ 2000 lbs
ELITE S E R I E S
The SL3000UL1HP™ is our most powerful slide
gate operator. Equipped with two ½ HP motors and
a heavy-duty transmission, it is the perfect choice
for large, heavy wrought iron gates. With 210 lbs. of
pulling torque, the unit is capable of 35 cycles per
hour on gates weighing up to 2,000 lbs. and up to
37 ft. In length.
The SL3000UL1HPE have been specially designed
to meet fire marshal’s requirements for fire and
emergency access. In the event of power loss, the
solenoid brake is automatically released, giving
emergency personnel the ability to push the gate
open. When power is normal you still can release
the gate by a manual button on the operator.
Now with Security+ 2.0 Technology &
Model 850LM universal receiver installed.
Now with Security+ 2.0 Technology &
Model 850LM universal receiver installed.
EMERGENCY ACCESS
GATE OPERATOR
LMSL3000UL1HP8
25” H. x 19” W. x 18” D.
UL325
UL991
Compliant
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
Equipped with two ½ HP, parking gate motors that work together
Duty Cycle
35 cycles per hour
Power Options
120 V AC, 8 amp
Cover
Molded Plastic - Weather Proof - Access Door
Fail Safe
No
Maximum Gate Length
37 Feet
Maximum Gate Weight
1 HP Motor - 2000 lbs.
Gate Speed
12 inches per sec.
Operator Weight
157 lbs.
Chain Size
#41 - 25 ft.
Emergency Release Options Manual Disconnect
Battery Backup Installed
No
SL3000UL1HPE
25” H. x 19” W. x 18” D.
UL325
UL991
Compliant
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
Equipped with two ½ HP, parking gate motors that work together
Duty Cycle
35 cycles per hour
Power Options
120 V AC, 8 amp
Cover
Molded Plastic - Weather Proof - Access Door
Fail Safe
Yes
Maximum Gate Length
37 Feet
Maximum Gate Weight
1 HP Motor - 2000 lbs.
Gate Speed
12 inches per sec.
Operator Weight
157 lbs.
Chain Size
#41 - 25 ft.
Emergency Release Options Push to open in case of power loss, or pressed manual button
Battery Backup Installed
No
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
Commercial Grade Dual Motor
SL3000ULDM Sliding Gate Operator
Commercial Grade Dual Motor with Battery Backup
SL3000ULDMDC Sliding Gate Operator
Dual - 1/2 HP ~ 800 lbs
ELITE S E R I E S
16-5
ELITE S E R I E S
Dual - 1/2 HP ~ 800 lbs
Unlike any other slide gate operator, the SL3000ULDM™
features a patented dual-motor drive system for superior
performance in hot weather climates such as desert environments. Engineered for high traffic commercial applications, the unit is designed to operate without overheating,
using one motor to open the gate and the other to
close it. Capabilities include continuous operation with
gates weighing up to 800 lbs. and up to 37 ft. In length.
Now with Security+ 2.0 Technology &
Model 850LM universal receiver installed.
UL325
UL991
Compliant
SL3000ULDM
25” H. x 19” W. x 18” D.
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Two - 1/2 HP - instant reversing, 1,625 rpm, high speed ball bearings
Motor
Duty Cycle
Continuous Duty
Power Options
120 V AC, 4 amp
Cover
Molded Plastic - Weather Proof - Access Door
Fail Safe
No
Maximum Gate Length
37 Feet
Maximum Gate Weight
Two ½ HP Motors - 800 lbs.
Gate Speed
12 inches per sec.
Operator Weight
157 lbs.
Chain Size
#41 - 25 ft.
Emergency Release Options Manual Disconnect
Battery Backup Installed
No
Unlike any other slide gate operator, the SL3000ULDMDC™
features a patented dual-motor drive system for superior performance in hot weather climates such as desert environments.
Engineered for high traffic commercial applications, the unit is
designed to operate without overheating, using one motor to
open the gate and the other to close it. Capabilities include
continuous operation with gates weighing up to 800 lbs. and up
to 37 ft. In length. SL3000ULDMDC™ comes with DC2000
power backup system factory installed.
1/2 HP ~ 18 ft. Gate - 600 lbs.
CSW200UL™ operators are ideal for high-traffic applications such as gated communities and commercial
buildings. Unlike other systems, the CSW gate operators are designed with a “non-scissor action” swing arm
to greatly reduce the risk of injury. Capabilities include
75 cycles per hour on gates weighing up to 600 lbs.
and up to 18 ft. In length.
SL3000ULDMDC
25” H. x 19” W. x 18” D.
Commercial Grade
CSW200UL1HP Swing Gate Operator
ELITE S E R I E S
1 HP ~ 22 ft. Gate - 1000 lbs.
CSW200UL1 HP™ is our most powerful swing gate operator.
Equipped with two 1/2 HP motors and a heavy-duty, 900:1
double transmission, it is the perfect choice for large, heavy
wrought iron gates. The CSW gate operators are designed with
a “non-scissor action” swing arm to greatly reduce the risk of
injury. With 250 lbs. of pulling torque, the unit is capable of 60
cycles per hour on gates weighing up to 1,000 lbs. and up to
20 ft. In length.
Now with Security+ 2.0 Technology &
Model 850LM universal receiver installed.
LMCSW200UL8
28” H. x 15” W. x 20.5” D.
UL325
UL991
Compliant
Now with Security+ 2.0 Technology &
Model 850LM universal receiver installed.
LMCSW200UL1HP8
28” H. x 15” W. x 24.5” D.
Specifications
UL325
UL991
Compliant
Specifications
UL 325 & UL 991 Compliant, ETL Listed
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
1/2 HP - instant reversing, 1,625 rpm, high speed ball bearings
Motor
Two 1/2 HP Motors that work together equaling 1 HP
Duty Cycle
Capable of 75 cycles per hour
Duty Cycle
Capable of 60 cycles per hour
Power Options
120 V AC, 4 amp
Power Options
120 V AC, 8 amp
Wormgear Reduction
Two 30-to-1 wormgear reducers in an oil bath.
Wormgear Reduction
Two 30-to-1 wormgear reducers in an oil bath.
Output Shaft
2-1/2” cold rolled steel
Output Shaft
2-1/2” cold rolled steel
Max. Gate Length & Weight
Max. Gate Length & Weight
Gate Speed
8 ft. Gate - 1600 lbs. / 12 ft. Gate - 1200 lbs.
16 ft. Gate - 800 lbs. / 18 ft. Gate - 600 lbs.
90 degree opening in 13-15 seconds
Gate Speed
12 ft. Gate - 2000 lbs. / 16 ft. Gate - 1600 lbs.
18 ft. Gate - 1400 lbs. / 22 ft. Gate - 1000 lbs.
90 degree opening in 13-15 seconds
Operator Weight
175 lbs.
Operator Weight
199 lbs.
Emergency Release Options Release handle is standard. Best option is our DC2000 (DCSW)
Emergency Release Options Release handle is standard.
Battery Backup Installed
Battery Backup Installed
No
UL325
UL991
Compliant
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Two - 1/2 HP - instant reversing, 1,625 rpm, high speed ball bearings
Motor
Duty Cycle
Continuous Duty
Power Options
120 V AC, 4 amp
Cover
Molded Plastic - Weather Proof - Access Door
Fail Safe
No
Maximum Gate Length
37 Feet
Maximum Gate Weight
Two ½ HP Motors - 800 lbs.
Gate Speed
12 inches per sec.
Operator Weight
157 lbs.
Chain Size
#41 - 25 ft.
Emergency Release Options Battery Backup Factory Installed - (DC2000)
Battery Backup Installed
Yes
Commercial Grade
CSW200UL Swing Gate Operator
ELITE S E R I E S
Now with Security+ 2.0 Technology &
Model 850LM universal receiver installed.
BATTERY BACKUP
FACTORY INSTALLED
No
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-6
Commercial Grade Dual Motor
CSW200ULDM Swing Gate Operator
Commercial Grade Dual Motor with Battery Backup
Dual 1/2 HP ~ 20 ft. Gate - 600 lbs
Dual - 1/2 HP ~ 20 ft. Gate - 600 lbs
ELITE S E R I E S
Unlike any other slide gate operator, the CSW200ULDM™
features a patented dual-motor drive system for superior
performance in hot weather climates such as desert environments. Engineered for high traffic commercial applications, the unit is designed to operate without overheating,
using one motor to open the gate and the other to
close it. Capabilities include continuous operation with
gates weighing up to 800 lbs. and up to 18 ft. In length.
Now with Security+ 2.0 Technology &
Model 850LM universal receiver installed.
UL325
UL991
Compliant
CSW200ULDM
28” H. x 15” W. x 24.5” D.
CSW200ULDMDC Sliding Gate Operator
ELITE S E R I E S
Unlike any other slide gate operator, the CSW200ULDMDC™
features a patented dual-motor drive system for superior performance in hot weather climates such as desert environments. Engineered for high traffic commercial applications, the
unit is designed to operate without overheating, using one
motor to open the gate and the other to close it. Capabilities include continuous operation with gates weighing up to
800 lbs. and up to 18 ft. In length. CSW200ULDMDC™ comes
with DC2000 power backup system factory installed.
Now with Security+ 2.0 Technology &
Model 850LM universal receiver installed.
BATTERY BACKUP
FACTORY INSTALLED
CSW200ULDMDC
28” H. x 15” W. x 24.5” D.
UL325
UL991
Compliant
Specifications
Specifications
UL 325 & UL 991 Compliant, ETL Listed
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
Two 1/2 HP - instant reversing, 1,625 rpm, high speed ball bearings
Motor
Two 1/2 HP - instant reversing, 1,625 rpm, high speed ball bearings
Duty Cycle
Capable of continuous cycles
Duty Cycle
Capable of continuous cycles
Power Options
120 V AC, 4 amp
Power Options
120 V AC, 4 amp
Wormgear Reduction
Two 30-to-1 wormgear reducers in an oil bath.
Wormgear Reduction
Two 30-to-1 wormgear reducers in an oil bath.
Output Shaft
2-1/2” cold rolled steel
Output Shaft
2-1/2” cold rolled steel
Max. Gate Length & Weight
Max. Gate Length & Weight
Gate Speed
12 ft. Gate - 1400 lbs. / 16 ft. Gate - 1000 lbs.
18 ft. Gate - 800 lbs. / 20 ft. Gate - 600 lbs.
90 degree opening in 13-15 seconds
Gate Speed
12 ft. Gate - 1400 lbs. / 16 ft. Gate - 1000 lbs.
18 ft. Gate - 800 lbs. / 20 ft. Gate - 600 lbs.
90 degree opening in 13-15 seconds
Operator Weight
199 lbs.
Operator Weight
199 lbs.
Emergency Release Options Release handle is standard.
Emergency Release Options
Battery Backup Factory Installed DC2000 (DCSW)
Battery Backup Installed
Battery Backup Installed
Yes
No
Residential / Light Commercial Operators from LiftMaster® ELITE Series
Designed for limited commercial applications, single family homes, or ranches
A Longer Lasting Battery Life With EverCharge® Power Management System
20-1/2” H. x 13” W. x 16-1/4” D.
RSL12V
RSW12V
SLIDE GATE OPERATOR
Power: 12VDC or 110v or Solar
Gate Capacity: 800 lbs
Gate Length: 25 ft.
Cycles: 120 times per day
Built-in Battery Back-up:
(Comes with a single battery installed)
Chain #41 - 25 ft.
Soft Start / Stop Operation
Operator Weight: 100 lbs.
Solar Ready
3 Year Warranty
UL325
SWING GATE OPERATOR
Power: 12VDC or 110v or Solar
Max. Gate Length & Weight:
12 ft. Gate - 600 lbs / 14 ft. Gate - 500 lbs.
16 ft. Gate - 400 lbs.
Cycles: 250 times per day
Built-in Battery Back-up:
(Comes with a single battery installed)
Soft Start / Stop Operation
Operator Weight: 180 lbs.
Solar Ready
3 Year Warranty
UL991
Compliant
LMRSL12V
Accessories Available:
Solar Package: LM7AHSLRPKG - Comes with a 20
watt solar panel 26” W. x 12” H, extra battery and wiring
Harness.
Transformer: LMK204B0195-1 - 12 V transformer
Wiring Harness: LMMSWIRE12GA6C - Wiring
Harness for a Master/Slave set up.
Battery Back-up Operation
(16 ft. / 650 lbs. slide gate.
Stand alone system)
Battery
Cycles
1 - 7AH
40
2 - 7AH
100
1 - 33AH
275
28-1/2” H. x 15-1/4” W. x 20-1/4” D.
UL325
UL991
Compliant
LMRSW12V
Accessories Available:
Solar Package: LM7AHSLRPKG - Comes with a 20
watt solar panel 26” W. x 12” H, extra battery and wiring
Harness.
Transformer: LMK204B0195-1 - 12 V transformer
Wiring Harness: LMMSWIRE12GA6C - Wiring
Harness for a Master/Slave set up.
Battery Back-up Operation
(16 ft. / 400 lbs. swing gate)
Battery
Cycles
1 - 7AH
40
2 - 7AH
100
1 - 33AH
275
1) You Can Bring 110v to the Unit. 2) You Can Use Remote Low Voltage Cable. 3) You Can Install Solar Power.
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-7
Residential and Commercial
F-1
The F-1™ Swing Gate Operator
™
CLASS I, CLASS II, CLASS III, and CLASS IV Vehicular Gate Operator
Operational Specifications
Operation: 24 VDC with 1/2 HP Motor
Main Power Source: 120/220 VAC Single Phase
Battery: 7 AMP Hour 12 VDC x 2
Capacity: 1200 lbs. / 12’ or 800 lbs. / 16’
Max. Opening Speed: 13-16 Seconds per 90°
Battery Back-up: 300 Full Cycles (600 lbs. / 12’ Gate)
Max Duty Cycle: 100 % (Continuous Cycles)
Temperature: -4° F to + 158° F
UL 325 and 991 Listing
Fail-safe / Fail-secure Clutch Mechanism
Loop Rack Included
Built-in Three Push Button Station
On-Board Lightning Protection
Soft-start / Soft-stop W / Intelligent Obstruction Detection
Solar Panel Ready: Requires 24VDC 80 watts
Limited Factory Warranty:
7 Year Residential and 5 Year Commercial
Wt. 134 lbs.
UL325
UL991
Compliant
VIKF-1
Overall Size
Optional Accessories
19-1/4” W. x 21-1/2” H. x 16-1/2” D.
Gear Head Heater: Required to operate in temperatures below 0° F
Solar Package: Part # VIKVA-SOCHP Rated at 12VDC-40 watts. 2 Panels required.
Power Box: A solution where operator is not near electricity 120 or 220 VAC
Magnetic Lock System: Holding force 1300 lbs when the electromagnet is energized.
Loop Rack: Plug up to three loop detectors. The installation is simple using only two connections.
Pipe Stands: These stands provide a flexible solution where concrete pads aren’t possible.
Bluetooth Technology: You can transmit and receive all commands of the gate operator for trouble shooting.
T-21
™
Heavy Duty Commercial
The T-21™ Swing Gate Operator
VIKINGBLUE Communication - Wireless operation using bluetooth® technology. You can transmit and receive all commands of the gate operator, it’s parameters, and troubleshoot it up to 100 ft away on your wireless smart device or laptop.
#VIKVA-BLUE-MSKT - Viking Wireless M/S Connect with Smart Diagnostics.
#VIKVA-BLUE - Viking Wireless M/S Connection.
Residential
R-6
™
The R-6™ Swing Gate Operator
CLASS I, CLASS II, CLASS III, and CLASS IV Vehicular Gate Operator
CLASS I, Vehicular Gate Operator
Operational Specifications
VIKT-21
Operation: 24 VDC With 1 H.P. Motor
Main Power Source: 120/220 VAC Single Phase
Battery: 7 AMP Hour 12 VDC x 2
Capacity: 1200 lbs. / 20’ - 2000 lbs. / 12’
Max. Opening Speed: 13-16 Seconds per 90°
Battery Back-up: 100 Full Cycles (600 lbs. / 12’ Gate)
Max Duty Cycle: 100% (Continuous Cycles)
Temperature: -4° F to + 158° F
UL 325 and 991 Listing
Fail-safe / Fail-secure Clutch Mechanism
Loop Rack Included
On-Board Lightning Protection
Soft-start / Soft-stop W / Intelligent Obstruction Detection
Solar Panel Ready: Requires 24VDC 80 watts
Limited Factory Warranty:
7 Year Residential and 5 Year Commercial
Wt. 190 lbs.
UL325
UL991
Compliant
Overall Size
21-1/2” W. x 27” H. x 16-1/2” D.
Optional Accessories
VIKINGBLUE Communication - Wireless operation using bluetooth® technology. You can transmit and receive all commands of the gate operator, it’s
parameters, and troubleshoot it up to 100 ft away on your
wireless smart device or laptop.
#VIKVA-BLUE-MSKT - Viking Wireless M/S Connect
with Smart Diagnostics.
#VIKVA-BLUE - Viking Wireless M/S Connection.
Gear Head Heater: Required to operate in temperatures below 0° F
Solar Package: Part # VIKVA-SOCHP Rated at 12VDC-40 watts. 2 Panels required.
Power Box: A solution where operator is not near electricity 120 or 220 VAC
Magnetic Lock System: Holding force 1300 lbs when the electromagnet is energized.
Loop Rack: Plug up to three loop detectors. The installation is simple using only two connections.
Pipe Stands: These stands provide a flexible solution where concrete pads aren’t possible.
Bluetooth Technology: You can transmit and receive all commands of the gate operator for trouble
shooting.
Operational Specifications
VIKR-6
UL325
UL991
Compliant
Operation: 24 VDC
Main Power Source: 120/220 VAC Single Phase
Battery: 7 AMP Hour 12 VDC x 2
Capacity: 600 lbs.
Max Gate Length: 14 Feet
Max. Opening Speed: 13-16 Seconds per 90°
Battery Back-up: 800 Full Cycles (500 lbs. / 12’ Gate)
Max Opening: 120°
Temperature: -4° F to + 158° F
UL 325 and 991 Listing
Fail-safe / Fail-secure Clutch Mechanism
On-Board Lightning Protection
Soft-start / Soft-stop W / Intelligent Obstruction Detection
Solar Panel Ready: Requires 24VDC 80 watts
Limited Factory Warranty: 5 Year Residential
Wt. 125 lbs.
Overall Size
19-1/4” W. x 21-1/2” H. x 16-1/2” D.
Optional Accessories
VIKINGBLUE Communication - Wireless operation using bluetooth® technology. You can transmit and receive all commands of the gate operator, it’s
parameters, and troubleshoot it up to 100 ft away on your
wireless smart device or laptop.
#VIKVA-BLUE-MSKT - Viking Wireless M/S Connect
with Smart Diagnostics.
#VIKVA-BLUE - Viking Wireless M/S Connection.
Gear Head Heater: Required to operate in temperatures below 0° F
Solar Package: Part # VIKVA-SOCHP Rated at 12VDC-40 watts. 2 Panels required.
Power Box: A solution where operator is not near electricity 120 or 220 VAC
Magnetic Lock System: Holding force 1300 lbs when the electromagnet is energized.
Loop Rack: Plug up to three loop detectors. The installation is simple using only two connections.
Pipe Stands: These stands provide a flexible solution where concrete pads aren’t possible.
Bluetooth Technology: You can transmit and receive all commands of the gate operator for trouble shooting.
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-8
Residential and Commercial
G-5
The G-5™ Swing Gate Operator
™
CLASS I, CLASS II, CLASS III, and CLASS IV Vehicular Gate Operator
The NEW
2000 lb.
Capacity
Viking G-5 Controller
Operational Specifications
UL325
UL991
Compliant
Operation: 24 VDC with 1/2 HP Motor
Main Power Source: 115/230 VAC Single Phase
Battery: 7 AMP Hour 12 VDC x 2
10 ft. Gate - 2000 lbs. / 12 ft. Gate - 1500 lbs.
16 ft. Gate - 1000 lbs. / 18 ft. Gate - 800 lbs.
Max. Opening Speed: 15-18 Seconds per 90°
The G-5 will Open Inside to a 120°. Open Outside to a 105°
Fail-Safe / Fail-Secure Option
Battery Back-up: 400 Full Cycles (600 lbs. / 12’ Gate)
Max Duty Cycle: 100 % (Continuous Cycles)
Temperature: -4° F to + 158° F
Access Key Release For Manual Operation
Built-in Three Push Button Station
On-Board Lightning Protection
Solar Panel Ready: Requires 24VDC 80 watts
Limited Factory Warranty: 4 Year Res. and 3 Year Com.
Wt. 80 lbs. Single Arm with Control Box
Wt. 118 lbs. Double Arms with Control Box
VIKECU-SGL-IN
Viking G-5 Single Arm Controller
VIKECU-M/S-IN
Viking G-5 Arm
Viking G-5 Master/Slave Arm Controller
VIKG-5NX ARM
Arm: 4” W. x 4-3/4” H. x 41.75” L.
Control Box: 15” W. x 14” H. x 6-1/2” D.
Revolutionizing The
Idea of Gate Operation!
Optional Accessories
Solar Package: Part # VIKVA-SOCHP Rated at 12VDC-40 watts. 2 Panels required.
Power Box: A solution where operator is not near electricity 120 or 220 VAC
Magnetic Lock System: Holding force 1300 lbs when the electromagnet is energized.
Loop Rack: Plug up to three loop detectors. The installation is simple using only two connections.
Bluetooth Technology: You can transmit and receive all commands of the gate operator for trouble
shooting.
Residential and Commercial
The X-9™ Swing Gate Operator
X-9
™
VIKINGBLUE Communication - Wireless operation using bluetooth®
technology. You can transmit and receive all commands of the gate operator, it’s parameters, and troubleshoot it up to 100 ft away on your wireless smart device or laptop.
#VIKVA-BLUE-MSKT - Viking Wireless M/S Connect with Smart Diagnostics
#VIKVA-BLUE
- Viking Wireless M/S Connection
i-8
™
Underground
The i-8™ Swing Gate Operator
CLASS I, CLASS II, CLASS III, and CLASS IV Vehicular Gate Operator
CLASS I, CLASS II, CLASS III, and CLASS IV Vehicular Gate Operator
UL325
UL991
Compliant
Operational Specifications
Viking X-9 Controller
Viking X-9 Arm
VIKX-9
Viking X-9 Arm
VIKECU-SGL-IN
Viking X-9 Single Arm Controller
VIKECU-M/S-IN
Operation: 24 VDC With 1/2 H.P. Motor
Main Power Source: 120/220 VAC Single Phase
Battery: 7 AMP Hour 12 VDC x 2
Capacity: 600 lbs.
Max. Gate Length: 14 FT.
Max. Opening Speed: 10-13 Seconds per 90°
The X-9 will Open Inside to a 120°. Open Outside to a 105°
Battery Back-up: 800 Full Cycles (500 lbs. / 12’ Gate)
Max Duty Cycle: 100% (Continuous Cycles)
Temperature: -4° F to + 158° F
UL 325 and 991 Listing
On-Board Lightning Protection
Adjustable Timer For Automatic Closure
Intelligent Obstruction Detection
Solar Panel Ready: Requires 24VDC 80 watts
Limited Factory Warranty:
3 Year Residential and 2 Year Commercial
Wt. 81 lbs. Single Arm with Control Box
Wt. 122 lbs. Double Arm with Control Box
Viking X-9 Master/Slave Arm Controller
VIKINGBLUE Communication - Wire-
Arm:
14-3/4” W. x 5.9” H. x 5.12” D.
Control Box:
15” W. x 14” H. x 6-1/2” D.
less operation using bluetooth® technology. You can transmit and receive all commands of the gate operator, it’s
parameters, and troubleshoot it up to 100 ft away on your
wireless smart device or laptop.
#VIKVA-BLUE-MSKT - Viking Wireless M/S Connect
with Smart Diagnostics.
#VIKVA-BLUE - Viking Wireless M/S Connection.
Optional Accessories
Solar Package: Part # VIKVA-SOCHP Rated at 12VDC-40 watts. 2 Panels required.
Power Box: A solution where operator is not near electricity 120 or 220 VAC
Magnetic Lock System: Holding force 1300 lbs when the electromagnet is energized.
Loop Rack: Plug up to three loop detectors. The installation is simple using only two connections.
Bluetooth Technology: You can transmit and receive all commands of the gate operator for trouble shooting.
UL325
UL991
Compliant
Operational Specifications
Viking I-8 Controller
Viking I-8 Arm
16.61” W. x 8.85” H. x 13.46” D.
VIKi-8
Viking I-8 Arm
VIKi-8SS
Viking I-8 Stainless Steel Arm
VIKECU-SGL-I8
Viking I-8 Single Arm Controller
VIKECU-M/S-I8
Viking I-8 Master/Slave Arm Controller
Operation: 24 VDC With 1/2 H.P. Motor
Main Power Source: 120/220 VAC Single Phase
Battery: 7 AMP Hour 12 VDC x 2
Capacity: 650 lbs.
Max Gate Length: 15 Feet
Max. Opening Speed: 13-15 Seconds per 90°
Battery Back-up: 400 Full Cycles (500 lbs. / 12’ Gate)
Temperature: -4° F to + 158° F
UL 325 and 991 Listing
Water Resistant Gear Head Unit
Key Release For Manual Release
Internal Parts: Aluminum, Stainless Steel, and Planted Steel
Positive Stop System
Stainless Steel Casing Available
Solar Panel Ready: Requires 24VDC 80 watts
Limited Factory Warranty:
3 Year Residential and 2 Year Commercial
Wt. 116.5 lbs. Single Arm with Control Box
Wt. 193. lbs. Double Arm with Control Box
VIKINGBLUE Communication - Wireless operation using bluetooth® technology. You can transmit and receive all commands of the gate operator, it’s
parameters, and troubleshoot it up to 100 ft away on your
wireless smart device or laptop.
#VIKVA-BLUE-MSKT - Viking Wireless M/S Connect
with Smart Diagnostics.
#VIKVA-BLUE - Viking Wireless M/S Connection.
Optional Accessories
Solar Package: Part # VIKVA-SOCHP Rated at 12VDC-40 watts. 2 Panels required.
Power Box: A solution where operator is not near electricity 120 or 220 VAC
Magnetic Lock System: Holding force 1300 lbs when the electromagnet is energized.
Loop Rack: Plug up to three loop detectors. The installation is simple using only two connections.
Bluetooth Technology: You can transmit and receive all commands of the gate operator for trouble shooting.
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-9
Residential and Commercial
L-3
The L-3™ Slide Gate Operator
™
CLASS I, CLASS II, CLASS III, and CLASS IV Vehicular Gate Operator
Operational Specifications
VIKL-3NX
UL325
UL991
Compliant
21.25” W. x 25.50” H. x 14.5” D.
Revolutionizing
The Idea of Gate Operation!
Operation: 24 VDC with 1/2 HP Motor
Main Power Source: 120/220 VAC Single Phase
Battery: 7 AMP Hour 12 VDC x 2
Capacity: 1600 lbs.
Max. Gate Length: 60 FT.
Max. Opening Speed: 12” Per Second
Innovative Fine Tune Adjustment - Down to 1/8”
Fail-Safe / Fail-Secure Option
Loop Rack Included
Soft-start, Soft-stop with Adaptive Learn Algorithm
Battery Back-up: 100 Full Cycles (1000 lbs. / 20’ Gate)
Max Duty Cycle: 100 % (Continuous Cycles)
Temperature: -4° F to + 158° F
#40 Chain Nickel Coated - 25 ft.
Access Switch For Manual Operation
On-Board Lightning Protection
Solar Panel Ready: Requires 24VDC 80 watts
Limited Factory Warranty: 7 Year Res. and 5 Year Com.
Wt. 90 lbs.
Optional Accessories
Gear Head Heater: Required to operate in temperatures below 0° F
Solar Package: Part # VIKVA-SOCHP Rated at 12VDC-40 watts. 2 Panels required.
Power Box: A solution where operator is not near electricity 120 or 220 VAC
Magnetic Lock System: Holding force 1300 lbs when the electromagnet is energized.
Loop Rack: Plug up to three loop detectors. The installation is simple using only two connections.
Pipe Stands: These stands provide a flexible solution where concrete pads aren’t possible.
Bluetooth Technology: You can transmit and receive all commands of the gate operator for trouble
shooting.
VIKINGBLUE Communication - Wireless operation using bluetooth®
technology. You can transmit and receive all commands of the gate operator, it’s parameters, and troubleshoot it up to 100 ft away on your wireless smart device or laptop.
#VIKVA-BLUE-MSKT - Viking Wireless M/S Connect with Smart Diagnostics.
#VIKVA-BLUE - Viking Wireless M/S Connection.
Residential
K-2
™
The K-2™ Slide Gate Operator
CLASS I, CLASS III, and CLASS IV Vehicular Gate Operator
Operational Specifications
VIKK-2
UL325
UL991
Compliant
19.5” W. x 19.50” H. x 13.5” D.
Revolutionizing the
Idea of Gate Operation!
Optional Accessories
Gear Head Heater: Required to operate in temperatures below 0° F
Solar Package: Part # VIKVA-SOCHP Rated at 12VDC-40 watts. 2 Panels required.
Power Box: A solution where operator is not near electricity 120 or 220 VAC
Magnetic Lock System: Holding force 1300 lbs when the electromagnet is energized.
Loop Rack: Plug up to three loop detectors. The installation is simple using only two connections.
Pipe Stands: These stands provide a flexible solution where concrete pads aren’t possible.
Bluetooth Technology: You can transmit and receive all commands of the gate operator for trouble
shooting.
Operation: 24 VDC with 1/2 HP Motor
Main Power Source: 120/220 VAC Single Phase
Battery: 7 AMP Hour 12 VDC x 2
Capacity: 650 lbs.
Max. Gate Length: 27 FT
Max. Opening Speed: 12” Per Second
Fail-Safe / Fail-Secure Option
Battery Back-up: 100 Full Cycles (650 lbs. / 20’ Gate)
Max Duty Cycle: 100 % (Continuous Cycles)
#40 Chain Nickel Coated - 25 ft.
Temperature: -4° F to + 158° F
Access Switch For Manual Operation
Built-in Three Push Button Station
On-Board Lightning Protection
Solar Panel Ready: Requires 24VDC 80 watts
Limited Factory Warranty: 5 Year Residential
Wt. 80 lbs.
VIKINGBLUE Communication - Wireless operation using bluetooth®
technology. You can transmit and receive all commands of the gate operator, it’s parameters, and troubleshoot it up to 100 ft away on your wireless smart device or laptop.
#VIKVA-BLUE-MSKT - Viking Wireless M/S Connect with Smart Diagnostics.
#VIKVA-BLUE - Viking Wireless M/S Connection.
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-10
Residential and Commercial
H-10
™
The H-10™ Slide Gate Operator
CLASS I, CLASS II, CLASS III, and CLASS IV Vehicular Gate Operator
Operational Specifications
VIKH-10NX
19.5” W. x 23.50” H. x 13.5” D.
Revolutionizing The
Idea of Gate Operation!
Optional Accessories
Gear Head Heater: Required to operate in temperatures below 0° F
Solar Package: Part # VIKVA-SOCHP Rated at 12VDC-40 watts. 2 Panels required.
Power Box: A solution where operator is not near electricity 120 or 220 VAC
Magnetic Lock System: Holding force 1300 lbs when the electromagnet is energized.
Loop Rack: Plug up to three loop detectors. The installation is simple using only two connections.
Pipe Stands: These stands provide a flexible solution where concrete pads aren’t possible.
Bluetooth Technology: You can transmit and receive all commands of the gate operator
for trouble shooting.
Operation: 24 VDC with 1 HP Motor
Main Power Source: 120/220 VAC Single Phase
Battery: 7 AMP Hour 12 VDC x 2
Capacity: 2200 lbs.
Max. Gate Length: 40 FT.
Max. Opening Speed: 12” Per Second
Innovative Fine Tune Adjustment - Down to 1/8”
Fail-Safe / Fail-Secure Option
Loop Rack Included
Soft-start, Soft-stop with Adaptive Learn Algorithm
Battery Back-up: 100 Full Cycles (1000 lbs. /20’ Gate)
Max Duty Cycle: 100 % (Continuous Cycles)
#40 Chain Nickel Coated - 25 ft
Temperature: -4° F to + 158° F
Access Switch For Manual Operation
On-Board Lightning Protection
Solar Panel Ready: Requires 24VDC 80 watts
Limited Factory Warranty: 7 Year Res. and 5 Year Com.
Wt.120 lbs.
UL325
UL991
Compliant
VIKINGBLUE Communication - Wireless operation using bluetooth®
technology. You can transmit and receive all commands of the gate operator, it’s
parameters, and troubleshoot it up to 100 ft away on your wireless smart device or
laptop.
#VIKVA-BLUE-MSKT - Viking Wireless M/S Connect with Smart Diagnostics
#VIKVA-BLUE - Viking Wireless M/S Connection
Residential and Commercial
Q-4
™
The Q-4™ Slide Gate Operator
CLASS II, CLASS III, and CLASS IV Vehicular Gate Operator
Operational Specifications
VIKQ-4
20” W. x 26” H. x 14” D.
Revolutionizing The
Idea of Gate Operation!
Optional Accessories
Gear Head Heater: Required to operate in temperatures below 0° F
Power Box: A solution where operator is not near electricity 120 or 220 VAC
Magnetic Lock System: Holding force 1300 lbs when the electromagnet is energized.
Loop Rack: Plug up to three loop detectors. The installation is simple using only two connections.
Pipe Stands: These stands provide a flexible solution where concrete pads aren’t possible.
Bluetooth Technology: You can transmit and receive all commands of the gate operator
for trouble shooting.
Operation: 24 VDC
Main Power Source: 120/220 VAC Single Phase
Battery: 33 to 100 AMP Hour 12 VDC x 2
1/2 Kilowatt of Power
Capacity: 4000 lbs.
Max. Gate Length: 80 FT.
Max. Opening Speed: Up to 16” Per Second
Innovative Fine Tune Adjustment - Down to 1/8”
Fail-Safe / Fail-Secure Option
Loop Rack Included
Adjustable Height for the main drive
Soft-start, Soft-stop with Adaptive Learn Algorithm
Battery Back-up: 100 Full Cycles (2000 lbs. / 40’ Gate)
Max Duty Cycle: 100 % (Continuous Cycles)
#40 Chain Nickel Coated - 25 ft.
Temperature: -4° F to + 158° F
Access Switch For Manual Operation
Limited Factory Warranty: 5 Year Res. and 5 Year Com.
Wt. 190 lbs.
UL325
UL991
Compliant
VIKINGBLUE Communication - Wireless operation using bluetooth®
technology. You can transmit and receive all commands of the gate operator, it’s
parameters, and troubleshoot it up to 100 ft away on your wireless smart device or
laptop.
#VIKVA-BLUE-MSKT - Viking Wireless M/S Connect with Smart Diagnostics
#VIKVA-BLUE - Viking Wireless M/S Connection
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-11
Residential
The 6050 Series Swinging Gate Operator
CLASS I Vehicular Gate Operator
Key Features:
Specifications:
Max. Gate: 10 FT.
Max. Gate Weight: 400 lbs.
DK6050-080 Swings gate 90 degrees in approx. 10 sec.
1/2 HP limited-duty motor.
Secondary Operator
10 cycles per hr.
DK6050-081 115 VAC, 4.3 Amps.
Operating Temp. 10° F to 140° F.
Shown With:
5 year limited factory warranty.
Pad Mount
Dimensions on operator only:
(Pad Mount sold separately)
13.25” W. x 12” H. x 23” D.
Wt. 100-140 lbs. Depending on model and
Reliable And options selected.
Primary Operator
Long Lasting!
Options Available:
Bi-parting gate connection cable.
UL325
Post or pad mount - specify which.
UL991
Compliant Plug-in loop detectors.
Heater Kit for cold environments.
Surge suppressors.
Shown With:
Post Mount
(Post Mount sold separately)
Pad Mount Kit
DK2600-671
Post Mount Kit
DK2600-674
* Self-adjusting, no maintenance magnetic limits.
* Overlap feature for dual swing gate operation.
* Designed with a built-in primary and secondary
entrapment prevention system.
* Ports for plug-in loop detectors.
* Fail-safe release.
* Tamper detect circuit.
* Gate tracker reporting output.
* Programming switches.
* Built-in reset switch.
* Built-in power On/Off switch.
* Quiet operation
* Weather proof design
* Keyed release for manual operation
* Compliant with UL 325 and 991. ETL Listed. (Note: To
be compliant entrapment prevention devices may
need to be installed with this gate operator.)
The unique design of these operators
allows the gate arm to be attached to the
bottom rail of the gate. This eliminates
the need for any brackets to be welded to
the face of the gate and creates an aesthetically pleasing installation.
Residential
The 6100 Series Swinging Gate Operator
CLASS I, CLASS II, CLASS III and CLASS IV Vehicular Gate Operator
Specifications:
Max. Gate: 14 FT.
Max. Gate Weight: 500 lbs.
DK6100-080 Swings gate 90 degrees in approx. 10 sec.
1/2 HP contiuous-duty motor.
Secondary Operator
60 Cycles per hr
DK6100-081 115 VAC, 5.4 Amps.
Operating Temp. 10° F to 140° F.
Shown With:
5 year limited factory warranty.
Pad Mount
Dimensions on operator only:
(Pad Mount sold separately)
13.25” W. x 12” H. x 23” D.
Wt. 100-140 lbs. Depending on model and
Reliable And options selected.
Primary Operator
Long Lasting! Options Available:
Bi-parting gate connection cable.
UL325 Post or pad mount - specify which.
UL991 DC powered convenience open.
Compliant Plug-in loop detectors.
Shown With:
Post Mount
(Post Mount sold separately)
Heater Kit for cold environments.
Surge suppressors.
Pad Mount Kit
DK2600-671
Post Mount Kit
DK2600-674
Key Features:
* Self-adjusting, no maintenance magnetic limits.
* Overlap feature for dual swing gate operation.
* Designed with a built-in primary and secondary
entrapment prevention system.
* Ports for plug-in loop detectors.
* Fail-safe release.
* Tamper detect circuit.
* DC Powered convenience open
* Gate tracker reporting output.
* Programming switches.
* Built-in reset switch.
* Built-in power On/Off switch.
* Quiet operation
* Weather proof design
* Keyed release for manual operation
* Compliant with UL 325 and 991. ETL Listed. (Note: To
be compliant entrapment prevention devices may
need to be installed with this gate operator.)
The unique design of these operators
allows the gate arm to be attached to the
bottom rail of the gate. This eliminates
the need for any brackets to be welded to
the face of the gate and creates an aesthetically pleasing installation.
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-12
6003 Vehicular Swing Gate Actuator
6002 Vehicular Swing Gate Actuator
For Smaller Gates
For Larger Gates
Class of Operation I
Class of Operation I, II
DK6003-080
5" W x 5" H x 35" L
The Model 6002 swing gate actuator offers convenience and reliability in a compact design. It mounts
directly on your gate and pilaster,
simplifying installation and eliminating the need for concrete pads. The
powerful screw driven piston connects directly to the gate eliminating weak mechanical connections
and it is fully enclosed to prevent
dirt and other airborne corrosives
from contaminating the screw
threads. And there is no need to
worry about hydraulic leaks, check
valves or pumps.
Max Gate Weight: 300 Lbs.
Max. Length: 10 Ft
Control Panel: 115 VAC, 60 Hz
Operating Power: 24 VDC
Back-Up: Batteries Provided
Built-in Battery Charger
90° in approximately 12 seconds
2- year Limited Factory Warranty
Wt. 20-25 lbs. depends on control box
UL325
UL991
Compliant
Max Gate Weight: 500 Lbs.
Max. Length: 14 Ft
Control Panel: 115 VAC, 60 Hz
Operating Power: 24 VDC
Back-Up: Batteries Provided
Built-in Battery Charger
90° in approximately 12 seconds
110° Max. Gate Opening
2- year Limited Factory Warranty
Wt. 20-25 lbs. depends on control box
Deluxe
Control Box
Standard
Control Box
The deluxe control box
provides three 115 VAC
convenience outlets to
power auxiliary power
transformers.
The standard control
box is typically used for
applications not requiring power for additional
control devices.
DK4302-112
DK4302-111
14-1/4" W x 24-1/4" H x 4" D
UL325
UL991
Compliant
DK6002-080
50" L x 4" H x 4" D
The Model 6002 swing gate actuator offers convenience and
reliability in a compact design. It
mounts directly on your gate and
pilaster, simplifying installation
and eliminating the need for concrete pads. The powerful screw
driven piston connects directly to
the gate eliminating weak mechanical connections and it is
fully enclosed to prevent dirt and
other airborne corrosives from
contaminating the screw threads.
And there is no need to worry
about hydraulic leaks, check
valves or pumps.
12-1/4" W x 16-3/4" H x 4" D
Residential
The 9050 Series Sliding Gate Operator
CLASS I Vehicular Gate Operator
Reliable
And
Long
Lasting!
UL325
UL991
Compliant
Fail Secure Kit
For 9050
DK9050-080
DK2600-862
The Model 9050 operator is ideally used
and designed to operate vehicular slide
gates in residential applications only.
Key Features:
Specifications:
Max. Gate: 16 FT.
Max. Gate Weight: 300 lbs.
1/2 HP light-duty motor.
10 cycles per hr
115 VAC, 4.3 Amps.
Speed: Approx. 10” per second
Steel Cover
#41 chain - 20 Ft.
5-year limited factory warranty
Approx. 70 lbs
Operating Tempt: 10° F to 140° F
Dimensions on operator only:
12” W. x 24” H. x 11.5” D.
Wt. 70 lbs.
*
*
*
*
*
*
*
*
*
*
*
*
Light Duty - General Public Access
Electronic self setting limits
Built in mechanical and electronic reverse system
Built in power and alarm reset switches
Selectable loop function (stop and reverse)
Fail safe release
Ports for plug-in open and reverse loop detectors
(DKS loop detectors only)
Convenience outlets
Built-in power On/Off switch
Programming switches
Auto-close timer 1-23 sec.
Compliant with UL 325 and 991. ETL Listed. (Note:
To be compliant entrapment prevention devices
may need to be installed with this gate operator.)
Options Available
#40 chain
Nickel plated chain
Stainless steel chain
Plug-in loop detectors
Heater kit for cold environments
Base plate to post mount this operator
(does not include posts)
Surge suppressors
These operators are designed so that they
can easily be mounted in the front, center or
rear of the gate without any costly and time
consuming field modifications. In addition,
the operators can be pad or post mounted to
meet any installation requirements.
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-13
Commercial ~ Residential
Commercial ~ Residential
The SL-100 Sliding Gate Operator
The SL-100DC Sliding Gate Operator
1/2 HP ~ 1000 lbs
1/2 Hp - 2000 lbs ~ With BATTERY BACK-UP
The SL-100 is our most popular automatic
gate operator. Affordable, slim and rated for
continuous duty on gates up to 1000 lbs.
This is a 110 Volt AC device capable of
years and years of reliable service. The SL100 was originally intended for applications
like public storage facilities in the US. You
can imagine those gates have to work all
the time.
UL325
UL991
Compliant
ALLSL100 1/2HP
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
1/2 HP
Duty Cycle
Continuous
Power Options
120 V AC
Gear Box Ratio
10:1 & 30:1 Optional for fail secure applications
Chain
#41 - 20 ft.
Dimensions
W: 12” – L: 17.5” – H 23.5”
Maximum Gate Length
37 Feet
Maximum Gate Weight
1/2 HP Motor: 1000 lbs.
Gate Speed
12 inches per sec.
Operator Weight
100 lbs.
Emergency Release Options Can be pushed open in the event of a power failure
Battery Backup
Compatible
UL325
UL991
Compliant
Designed specifically to be the strongest, most
durable DC gate Operator in its class.
Allomatic’s long awaited SL-100 DC has arrived. The SL-100 DC utilizes an industry first
brushless motor technology (no maintenance,
high torque, and smooth quiet operation), total
in house design, programming and construction. Equipped with a built in loop detector rack
and enough power to operate all accessories
on battery power. Manufactured with a heavy
duty frame and parts that are made to last a life
time, plus our industry leading warranty.
ALLSL100 1/2DC
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
24 VDC Brushless Motor ½ HP – Continuous Duty Cycle
Duty Cycle
Continuous
Power Options
120/220 VAC Single Phase
Gear Box Ratio
10:1
Chain
#41 - 20 ft.
Dimensions
W: 12” – L: 17.5” – H 23.5”
Maximum Gate Length
45 Feet
Maximum Gate Weight
1/2 HP Motor: 2000 lbs.
Gate Speed
12 inches per sec
Operator Weight
130 lbs.
Emergency Release Options Can be pushed open in the event of a power failure
Battery Backup
IntegratedCapable of up to 80 cycles on a 1000lbs Gate
Battery: Two 8 Ah Batteries 12VDC
Solar Capabilities
12VDC or 24VDC Solar Panel Input
Commercial ~ Residential
Commercial ~ Residential
The SL-150 Sliding Gate Operator
The SL-150DC Sliding Gate Operator
1/2 HP & 1 HP
1/2 Hp & 1 HP ~ With BATTERY BACK-UP
This is our commercial slide operator. These operators run on gates for many high schools and
government facilities like power distribution centers and police impound/tow yeards. The SL-150
is in front of oil derricks and furniture warehouses.
It will operate gates up to 65 ft. and 8,000 lbs.
With its premier 1hp motor. The operator is also
available in affordable 1/2hp version.
All-O-Matic’s new SL-150 DC slide gate operator comes
equipped with a true integrated long term battery backup.
Like all of All-O-Matic’s DC gate operators the SL-150 DC
uses an industry first Brushless DC motor, witch means
zero maintenance and high precision. The SL-150 DC
comes equipped with a built in loop rack, slow start/stops
algorithm, heavy duty frame, emergency mechanical foot
pedal release. The SL-150 DC offers up to weeks of uninterrupted operation in the event of a power failure. Unlike
other currently available “open and die” single cycle battery backups, in the event of a power failure the SL-150
DC seamlessly switches from AC power to backup mode
and runs off of its included (2 - 8Ah) batteries.
ALLSL150 1/2HP
UL325
UL991
Compliant
ALLSL150 1HP
UL325
UL991
Compliant
ALLSL150 1/2DC
ALLSL150 1DC
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
½ HP, 1 HP
Duty Cycle
Continuous
Power Options
120 V AC
Gear Box Ratio
30:1 w/ Internal Clutch
Chain
#40 - 20 ft.
Dimensions
W: 15”- L: 19.5” – H: 25”
Maximum Gate Length
60 Feet
Maximum Gate Weight
1/2 HP Motor: 1500 lbs.
1 HP Motor: 2500 lbs
Gate Speed
12 inches per sec.
Operator Weight
150 lbs.
Emergency Release Options
Foot Pedal
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
24 VDC Brushless Motor ½ HP or 1HP – Continuous Duty Cycle
Duty Cycle
Continuous
Power Options
120/220 VAC Single Phase
Gear Box Ratio
30:1 w/ Internal Clutch
Chain
#40 - 20 ft.
Dimensions
W: 15”- L: 19.5” – H: 25”
Maximum Gate Length
60 Feet
Maximum Gate Weight
1/2 HP Motor: 3000 lbs.
1 HP Motor: 4000 lbs.
Gate Speed
12 inches per sec.
Operator Weight
150 lbs.
Emergency Release Options Foot Pedal
Battery Backup
Integrated Full Time Battery Backup Capable of up to 100 cycles on
a 1000 lbs Gate Battery: Two 8 Ah Batteries 12VDC
Solar Capabilities
12VDC or 24VDC Solar Panel Input
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-14
Commercial ~ Residential
Commercial ~ Residential
The SW-300 Swinging Gate Operator
The SW-300DC Swinging Gate Operator
1/2 HP
1/2 Hp ~ With BATTERY BACK-UP
The SW-300 is our residential and commercial gate operator. This will swing
gates up to 18 ft and 800 lbs. You can
see the SW-300 installed master/slave in
front of gated communities as well as
homes with circular driveways and any
flag lot where lateral space is limited. Its
silent, elegant slow-stop & slow-start features is the envy of the industry.
UL325
UL991
Compliant
ALLSW300 1/2HP
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
1/2 HP,
Duty Cycle
Continuous
Power Options
120 V AC
Gear Box Ratio
60:1
Cover
Rotationally Molded - Indestructible
Dimensions
W: 21”- L: 17” – H: 25.5”
Maximum Gate Length
18 Feet Max.
Maximum Gate Weight
1/2 HP Motor: 800 lbs
Gate Speed
90 degrees travel in 17 sec.
Operator Weight
110 lbs.
Emergency Release Options
Patented No-Bind, Band release Arm
Battery Backup
Compatible
Commercial ~ Residential
The SW-350 Swinging Gate Operator
1/2 HP, 3/4 HP, & 1 HP
UL325
UL991
Compliant
Designed specifically to be the strongest, most
durable DC gate Operator in its class. Allomatics long awaited SW-300 DC has arrived. The
SW-300 DC utilizes an industry first brushless
motor technology (no maintenance, high
torque, and smooth quiet operation), total in
house design, programming and construction.
Equipped with a built in loop detector rack and
enough power to operate all accessories on
battery power. Manufactured with a heavy duty
frame and parts that are made to last a life
time, plus our industry leading warranty.
ALLSW300 1/2DC
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
24 VDC Brushless Motor ½ HP – Continuous Duty Cycle
Duty Cycle
Continuous
Power Options
120/220 VAC Single Phase
Gear Box Ratio
60:1
Cover
Rotationally Molded - Indestructible
Dimensions
W: 21”- L: 17” – H: 25.5”
Maximum Gate Length
20 Feet Max.
Maximum Gate Weight
1/2 HP Motor: 1200 lbs
Gate Speed
Approx. 90 degrees travel in 17 sec.
Operator Weight
135 lbs.
Emergency Release Options No-Bind, Band release Arm
Battery Backup
Integrated -Capable of up to 250 Cycles
- Battery: Two 8 Ah Batteries 12VDC
Solar Capabilities
12VDC or 24VDC Solar Panel Input
Commercial ~ Residential
The SW-350DC Swinging Gate Operator
1/2 HP - With BATTERY BACK-UP
The SW-350 DC swing gate operator is the largest of Allomatics swing gate operators. This DC swing gate operator is capable of moving gates up to 2,000 Lbs or 22 feet in length. With
all of the assets of the original 350 design and all of the increased capability of the DC gate operator line, this operator is
unparalleled in its capability. Heavy duty torque limiter, huge
solid aluminum no rust no bind hub, mechanical foot pedal release, built in loop rack, low profile design, and full time battery
backup for seamless transition to battery mode in the event of
a power failure.
The SW-350 Swing Gate Operator has bin used on Gate of
up to 22’ and 2000 Lbs. Over the years its low profile design, heavy duty mechanical foot pedal release, unmatched
heavy duty clutch and no bind quick release arm w/ rust
proof aluminum hub have allowed All-O-Matics SW-350
heavy duty swing gate operator to stand out amongst the
rest. For tuff jobs there is no match. All All-O-Matic Gate Operators are covered by our 5/7 Year Manufacturers Warranty
ALLSW350 1/2HP
UL325
UL991
Compliant
ALLSW350 3/4HP
ALLSW350 1HP
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
1/2 HP, 3/4 HP or 1 HP
Duty Cycle
Continuous
Power Options
120 V AC
Gear Box Ratio
60:1 with internal clutch
Cover
Rotationally Molded - Indestructible
Dimensions
W: 14”- L: 24” – H: 18”
Maximum Gate Length
22 Feet Max.
Maximum Gate Weight
1/2 HP Motor: 800 lbs.
3/4 HP Motor: 1200 lbs.
1 HP Motor: 1500 lbs.
Gate Speed
90 degrees travel in 19 sec.
Operator Weight
125 lbs.
Emergency Release Options
Foot Pedal
UL325
UL991
Compliant
ALLSW350 1/2DC
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
24VDC Brush-less Motor 1/2 HP
Duty Cycle
Continuous Duty
Power Options
120\220 V AC Single Phrase
Gear Box Ratio
60:1 with internal clutch
Cover
Rotationally Molded - Indestructible
Dimensions
W: 14”- L: 24” – H: 18”
Maximum Gate Length
22 Feet Max.
Maximum Gate Weight
1/2 HP Motor: 2000 lbs.
Gate Speed
90 degrees travel in 19 sec.
Operator Weight
125 lbs.
Emergency Release Options Foot Pedal
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-15
Commercial ~ Residential
The SL-90DC Sliding Gate Operator
1/2 Hp - 1200 lbs ~ With BATTERY BACK-UP
UL325
UL991
Compliant
Designed specifically to be the strongest,
most durable DC gate Operator in its
class. The SL-90DC utilizes an industry
first brushless motor technology (no
maintenance, high torque, and smooth
quiet operation), total in house design,
programming and construction. Equipped
with a built in loop detector rack and
enough power to operate accessories on
battery power. Manufactured with a
heavy duty frame and parts that are
made to last a life time, plus there industry leading warranty.
ALLSL90 1/2DC
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
24 VDC Brushless Motor 1/2 HP – Continuous Duty Cycle
Duty Cycle
Continuous
Power Options
120/220 VAC Single Phase
Gear Box Ratio
15:1
Chain
#41 - 20 ft.
Dimensions
15-1/2” W. x 18-1/2” L. x 17” H.
Maximum Gate Length
40 Feet
Maximum Gate Weight
1/2 HP Motor: 1200 lbs.
Gate Speed
12 inches per sec.
Operator Weight
90 lbs.
Emergency Release Options Can be pushed open in the event of a power failure
Battery Backup
Integrated Capable of up to 150 cycles
Battery: Two 7 Ah Batteries 12VDC
Solar Capabilities
12VDC or 24VDC Solar Panel Input
Commercial ~ Residential
The OH-200 Overhead Gate Operator - 1/2 HP
This is a commercial gate operator for
overhead tilt up gates. You will see this
operator quietly operating gates for underground parking facilities and
apartment/condo buildings. Like All-OMatic gate operators the OH-200 is rated
for continous duty.
Commercial ~ Residential
The OH-200DC Overhead Gate Operator - 1/2 HP
With Battery Backup
All-O-Matics new OH-200 DC overhead gate operator is the first and only commercial overhead gate
operator available with a true integrated long term
battery backup. The OH-200 DC offers days of uninterrupted operation in the event of a power failure.
The OH-200 DC seamlessly switches from AC power
to backup mode and runs off of its included (2 - 8Ah)
batteries. For multi residential and commercial applications such as apartment buildings or large underground parking structures.
UL325
UL991
Compliant
UL325
UL991
Compliant
ALLOH200 1/2HP
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Warranty
Full 5 Year Commercial
Motor
1/2 HP Motor
Duty Cycle
Continuous
Gear Box Ratio
60:1
Dimensions
W: 13”- L: 144” – H: 8”
Maximum Gate Length
16 Feet Max.
Maximum Gate Weight
1/2 HP Motor: 800 lbs.
Operator Weight
100 lbs.
Overhead
Jamb
Track
Available
Please Call
Emergency Release Options Lockable Quick release Drive Arm and Carriage
Battery Backup
Compatible
ALLOH200 1/2HPDC
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Overhead
Warranty
Full 5 Year Commercial
Jamb
Motor
24 VDC Brushless 1/2 HP Motor
Track
Duty Cycle
Continuous
Available
Gear Box Ratio
40:1
Please Call
Dimensions
W: 13”- L: 144” – H: 8”
Maximum Gate Length
22 Feet Max.
Maximum Gate Weight
1/2 HP Motor: 800 lbs.
Operator Weight
110 lbs.
Emergency Release Options Lockable Quick release Drive Arm and Carriage
Battery Backup
Integrated -Capable of up to 100 Cycles
- Battery: Two 8 Ah Batteries 12VDC
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-16
Heavy Duty Commercial High Traffic
The 3020 Slide Gate Operator
CLASS I, CLASS II, CLASS III, and CLASS IV Vehicular Gate Operator
14” W. x 22” L. x 17” H.
DORDR3020
DORDR3020HX
1/2 HP 110 VAC
Max. Gate: 45 ft
Max. Gate Weight: 2200 lbs.
1 HP 110 VAC
Max. Gate: 45 ft
Max. Gate Weight: 3600 lbs.
Cycles: Continuous
Gate Travel: 12” Per Second
UL325
Shipping Weight: 135 lbs.
UL991
Pause Circuit (Anti-Tailgate)
Compliant
Electronic Brake
LED Diagnosis
Chain #41 - 25ft
Line Spike Protection
Adjustable Timer (0-63 seconds)
Advanced Adjustable Obstruction Sensor
Auto-Res. 24V Solid State Circuit Breaker
Emergency Release: Electronic Brake /no power-no brake
Chassis: Heavy Duty Structural Steel
Limited Factory Warranty:
6 Year Residential and 4 Year Commercial
All units are protected by a low profile,
high impact resistant, weather resistant and lockable molded plastic.
Heavy Duty Commercial High Traffic
The 4020 Swing Gate Operator
CLASS I, CLASS II, CLASS III, and CLASS IV Vehicular Gate Operator
16” W. x 21” L. x 21” H.
DORDS4020
Motor: 1/2 HP, 110/117 VAC
Max Gate Length: 16 ft
Max Gate Weight: 1800 lbs.
DORDS4020H
Motor: 1/2 HP, 110/117 VAC
Max Gate Length: 20 ft
Max Gate Weight: 2200 lbs.
DORDS4020HX
Motor: 1 HP, 110/117 VAC
Max Gate Length: 25 ft
Max Gate Weight: 3600 lbs.
Cycles: Continuous
Gate Travel: 22” Per Second
UL325
Shipping Weight: 180 lbs.
UL991
Pause Circuit (Anti-Tailgate)
Compliant
Electronic Brake
LED Diagnosis
Line Spike Protection
Adjustable Timer (0-63 seconds)
Advanced Adjustable Obstruction Sensor
Auto-Res. 24V Solid State Circuit Breaker
Emergency Release: Electronic Brake /no power-no brake
Chassis: Heavy Duty Structural Steel
Limited Factory Warranty:
6 Year Residential and 4 Year Commercial
All units are protected by a low profile, high
impact resistant, weather resistant and
lockable molded plastic.
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-17
CAME BX-243 Residential Slide Gate Operator
CAME ensures all their products are up to the highest safety standards, style and functionality. The Bx-243 has
undergone testing to bring it up to the United States and Canada standards in terms of the impact forces generated by the gate leaf movement. This is the ideal solution for residential installations for sliding gates up to
660 pounds, and features a complete operator, equipped with encoder-based movement control.
BX-243
Models Available
Residential Slider
120V AC, single phase
25 Cycles Per Day
25 ft. Gate. - 660 lbs.
Manual Release
7.5 inches per second
Chain #41 - 28 ft.
3 Year Residential Warranty
13” H. x 8.34” D. x 11.73” W.
BX-243C - Includes: Chain Drive Slide Gate Operator, control board
with Security+ 2.0™ on-board receiver chain drive & 28 ft. Chain - 36 lbs.
BX-243R - Includes: Rack and Pinion Slide Gate Operator, control
board with Security+ 2.0™ on-board receiver. Rack sold separately.
- 27 lbs.
Security+ 2.0™ technology 2x the range
ETL listed and UL-325 Compliant For Class 1
Adjustable speed control
Partial-Open feature
Soft Stop
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-18
CAME FERNI Residential Column-Mount Swing Gate Operator
The Ferni Residential Column-Mount Swing Gate Operator moves gates up to 13 feet wide. This unique system
enables gate automation when the dimensions of a large pillar prevents any other operator from being installed.
FERNI 1PKG
Residential Swing
Models Available
FERNI 1PKG - Includes FERNI operator, articulated transmission
120V AC, single phase
Motor power: 24V DC continuous duty
Accessory power: 24V AC, 2 amps
25 Cycles Per Day
6.5 ft. Gate - 1770 lbs.
8 ft. Gate - 1320 lbs.
13 ft. Gate - 880 lbs.
Manual Disconnect
90 degree opening in 16-45 seconds
3 Year Residential Warranty
Operator dimension:
6.61” H. x 7.16” D. x 13.38” W.
Control Box Dimension:
12.6” H. x 5.7” D. x 9.45” W.
arm and control box with Security+ 2.0™ on-board receiver - 48 lbs.
FERNI-S - Includes FERNI Secondary articulated transmission arm
for a M/S setup - 32 lbs.
Security+ 2.0™ technology 2x the range
ETL listed and UL-325 Compliant For Class 1
Adjustable speed control
Partial Open Feature
Soft Stop
CAME FROG Residential Under-Ground Swing Gate Operator
The Frog Residential Underground Swing Gate Operator is ideal for ornamental swing gates. Installed below grade
in a waterproof casing, and protected by a steel access plate that is flush with the driveway surface, it provides an
invisible solution.
FROG 1PKG
Residential Swing
Models Available
FROG 1PKG - Includes: FROG operator motor assembly,
control box with Security+ 2.0™ on-board receiver, foundation
case and Key release - 78 lbs.
120V AC, single phase
Motor power: 24V DC continuous duty
Accessory power: 24V AC, 2 amps
25 Cycles Per Day
6.5 ft. Gate - 1770 lbs.
8 ft. Gate - 1320 lbs.
11.5 ft Gate - 880 lbs.
Manual Disconnect
90 degree opening in 16-45 seconds
3 Year Residential Warranty
Operator Dimension:
6.5” H. x 12.99” D. x 15.94” W.
Control Box Dimension:
12.6” H. x 5.7” D. x 9.45” W.
FROG-S - Includes: FROG Secondary operator motor assembly for a M/S setup, foundation case and Key release - 62 lbs.
Security+ 2.0™ technology 2x the range
ETL listed and UL-325 Compliant For Class 1
Adjustable speed control
Partial Open Feature
Soft Stop
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-19
Eagle-2000 Commercial Grade
Fail-Safe Sliding Gate Operator
Eagle-2000 Commercial Grade
Fail-Secure Sliding Gate Operator
1/2 HP ~ 1000 lbs
1/2 HP ~ 1000 lbs
With four models to choose from, Eagle-2000 is the reliable
choice for all your commercial and industrial needs. Installation
is made simple with the advanced features you most often need
standard on every operator; features like Stop-Reverse allowing
your transmitter to work like a 3-button station, or motor brake
for added control on downhill applications.
Dual gate Master/Slave operation has never been easier. Just
two wires provide full Master/Slave communication. Global inputs between master and slave operators allow connection of
any accessories to either the master or slave and the Diamond
Control Board does the rest.
26” H. x 18” W. x 17” D.
EAG2000FSF
UL325
UL991
Compliant
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Limited Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
1/2 HP Continuous Duty AC
Duty Cycle
Continuous
Power Options
115V AC @ 60 Hz 5.7 amp
Cover
Molded Plastic - Weather Proof - Access Door
Fail Safe
Yes
Maximum Gate Length
45 Feet
Maximum Gate Weight
1/2 HP Motor: 1000 lbs.
Gate Speed
12 inches per sec.
Operator Weight
125 lbs.
Chain Size
#40 Chain Nickel Coated - 20 ft.
Emergency Release Options Push to Open
Battery Backup
No - (Optional Power I Battery Backup 40-80 Cycles)
With four models to choose from, Eagle-2000 is the reliable
choice for all your commercial and industrial needs. Installation
is made simple with the advanced features you most often need
standard on every operator; features like Stop-Reverse allowing
your transmitter to work like a 3-button station, or motor brake
for added control on downhill applications.
Dual gate Master/Slave operation has never been easier. Just
two wires provide full Master/Slave communication. Global inputs between master and slave operators allow connection of
any accessories to either the master or slave and the Diamond
Control Board does the rest.
26” H. x 18” W. x 17” D.
EAG2000FSC
UL325
UL991
Compliant
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Limited Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
1/2 HP Continuous Duty AC
Duty Cycle
Continuous
Power Options
115V AC @ 60 Hz 5.7 amp
Cover
Molded Plastic - Weather Proof - Access Door
Fail Safe
No
Maximum Gate Length
45 Feet
Maximum Gate Weight
1/2 HP Motor: 1000 lbs.
Gate Speed
12 inches per sec.
Operator Weight
125 lbs.
Chain Size
#40 Chain Nickel Coated - 20 ft.
Emergency Release Options Use Crank to Open
Battery Backup
No - (Optional Power I Battery Backup 40-80 Cycles)
Eagle-2000 Commercial Grade
Fail-Secure Sliding Gate Operator
Eagle-2000 Commercial Grade
Fail-Secure Sliding Gate Operator
1 HP ~ 2000 lbs
Dual 1/2 HP ~ 1000 lbs (One Motor to Open - One Motor to Close)
With four models to choose from, Eagle-2000 is the reliable
choice for all your commercial and industrial needs. Installation
is made simple with the advanced features you most often need
standard on every operator; features like Stop-Reverse allowing
your transmitter to work like a 3-button station, or motor brake
for added control on downhill applications.
Dual gate Master/Slave operation has never been easier. Just
two wires provide full Master/Slave communication. Global inputs between master and slave operators allow connection of
any accessories to either the master or slave and the Diamond
Control Board does the rest.
26” H. x 18” W. x 17” D.
EAG20001HP
UL325
UL991
Compliant
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Limited Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
1 HP Continuous Duty AC
Duty Cycle
Continuous
Power Options
115V AC @ 60 Hz 11.4 amp
Cover
Molded Plastic - Weather Proof - Access Door
Fail Safe
No
Maximum Gate Length
45 Feet
Maximum Gate Weight
1 HP Motor: 2000 lbs.
Gate Speed
12 inches per sec.
Operator Weight
150 lbs.
Chain Size
#40 Chain Nickel Coated - 20 ft.
Emergency Release Options Use Crank to Open
Battery Backup
No - (Optional Power 2 Battery Backup 40-80 Cycles)
With four models to choose from, Eagle-2000 is the reliable
choice for all your commercial and industrial needs. Installation
is made simple with the advanced features you most often need
standard on every operator; features like Stop-Reverse allowing
your transmitter to work like a 3-button station, or motor brake
for added control on downhill applications.
Dual gate Master/Slave operation has never been easier. Just
two wires provide full Master/Slave communication. Global inputs between master and slave operators allow connection of
any accessories to either the master or slave and the Diamond
Control Board does the rest.
26” H. x 18” W. x 17” D.
EAG2000DM
UL325
UL991
Compliant
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Limited Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
Dual 1/2 HP Continuous Duty AC
Duty Cycle
Continuous
Power Options
115V AC @ 60 Hz 5.7 amp
Cover
Molded Plastic - Weather Proof - Access Door
Fail Safe
No
Maximum Gate Length
45 Feet
Maximum Gate Weight
Two - 1/2 HP Motors: 1000 lbs.
Gate Speed
12 inches per sec.
Operator Weight
150 lbs.
Chain Size
#40 Chain Nickel Coated - 20 ft.
Emergency Release Options Use Crank to Open
Battery Backup
No - (Optional Power 1 Battery Backup 40-80 Cycles)
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-20
Eagle-1000 Residential Single Family Homes Eagle-1000 Residential Single Family Homes
Fail-Safe Sliding Gate Operator
Fail-Secure Sliding Gate Operator
1/2 HP ~ 500 lbs
1/2 HP ~ 500 lbs
Rated for continuous duty, Eagle-1000 operators deliver the reliable power you expect
for a wide range of residential sliding gates.
Installation is made simple with the advanced features you most often need standard on every operator.
EAG1000FSF
Rated for continuous duty, Eagle-1000 operators deliver the reliable power you expect
for a wide range of residential sliding gates.
Installation is made simple with the advanced features you most often need standard on every operator.
UL325
UL991
Compliant
22” H. x 15” W. x 13-1/2” D.
EAG1000FSC
UL325
UL991
Compliant
22” H. x 15” W. x 13-1/2” D.
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Limited Warranty
Full 5 Year Residential
Motor
1/2 HP Continuous Duty AC
Duty Cycle
Continuous
Power Options
115V AC @ 60 Hz 5.7 amp
Cover
Molded Plastic - Weather Proof - Access Door
Fail Safe
Yes
Maximum Gate Length
22 Feet
Maximum Gate Weight
1/2 HP Motor: 500 lbs.
Gate Speed
12 inches per sec.
Operator Weight
80 lbs.
Chain Size
#40 Chain Nickel Coated - 20 ft.
Emergency Release Options Push to Open
Battery Backup
No - (Optional Power I Battery Backup 40-80 Cycles)
Specifications
UL 325 & UL 991 Compliant, ETL Listed
Limited Warranty
Full 5 Year Residential
Motor
1/2 HP Continuous Duty AC
Duty Cycle
Continuous
Power Options
115V AC @ 60 Hz 5.7 amp
Cover
Molded Plastic - Weather Proof - Access Door
Fail Safe
No
Maximum Gate Length
22 Feet
Maximum Gate Weight
1/2 HP Motor: 500 lbs.
Gate Speed
12 inches per sec.
Operator Weight
80 lbs.
Chain Size
#40 Chain Nickel Coated - 20 ft.
Emergency Release Options Use Crank to Open
Battery Backup
No - (Optional Power I Battery Backup 40-80 Cycles)
Eagle-1 Residential Single Family Homes
Fail-Safe Sliding Gate Operator
Eagle-2 Residential Single Family Homes
Swing Gate Operator
1/2 HP ~ 300 lbs
1/2 HP ~ 300 lbs
Enjoy quality and reliability with the Eagle-I Slide
Gate Operator. Manufactured with the same quality and engineering as larger commercial and industrial gate operators, many of the advanced
features you most often need come standard.
Like every Eagle operator, the Eagle-I is built with
heavy-duty AC motors, quiet gearboxes and quality components throughout. Install Eagle and install confidence.
Enjoy quality and reliability with the Eagle-II
Swing Gate Operator. Manufactured with the
same quality and engineering as larger commercial and industrial gate operators, many of the
advanced features you most often need come
standard. Like every Eagle operator, the Eagle-II
is built with heavy-duty AC motors, quiet gearboxes and quality components throughout. Install
Eagle and install confidence.
EAG1FSF
20” H. x 15” W. x 12” D.
EAG2
25” H. x 16-1/2” W. x 15” D.
Specifications
Specifications
Limited Warranty
Full 5 Year Residential
Limited Warranty
Full 5 Year Residential
Motor
1/2 HP Continuous Duty AC
Motor
1/2 HP Continuous Duty AC
Duty Cycle
Continuous AC
Power Options
Duty Cycle
Continuous AC
115V AC @ 60 Hz 5.2 amp
Cover
Molded Plastic - Weather Proof - Access Door
Power Options
115V AC @ 60 Hz 5.2 amp
Fail Safe
Yes
Cover
Molded Plastic - Weather Proof - Access Door
Maximum Gate Length
16 Feet
Maximum Gate Length
14 Feet
Maximum Gate Weight
1/2 HP Motor: 300 lbs.
Maximum Gate Weight
1/2 HP Motor: 300 lbs.
Gate Speed
12 inches per sec.
Drive Chain
#50 Nickel Plated
Operator Weight
75 lbs.
Gate Speed
18 seconds to open 90 degrees
Chain Size
#40 Chain Nickel Coated - 20 ft.
Operator Weight
90 lbs.
Emergency Release Options Push to Open
Emergency Release Options Quick Release Lever
Battery Backup
Battery Backup
No - (Optional Power I Battery Backup 40-80 Cycles)
No - (Optional Power I Battery Backup 40-80 Cycles)
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Gate Operators
16-21
Eagle-200 Commercial Grade
Swing Gate Operator
Eagle-200 Commercial Grade
Swing Gate Operator
1/2 HP ~ 750 lbs
1 HP ~ 1000 lbs
With three models to choose from, Eagle-200 is the reliable choice for all your commercial and industrial
needs; big heavy gates with high traffic use and smooth
powerful operation. The Eagle-200 Commercial Swing
Gate Operator comes standard with the features you
most often need. Establish full communication between
master and slave operators with only two wires. With
Eagle's Global Inputs you can now connect accessories
to the master or slave operator.
EAG200
29-1/2” H. x 22-1/2” W. x 17” D.
UL325
UL991
Compliant
With three models to choose from, Eagle-200 is the reliable choice for all your commercial and industrial
needs; big heavy gates with high traffic use and smooth
powerful operation. The Eagle-200 Commercial Swing
Gate Operator comes standard with the features you
most often need. Establish full communication between
master and slave operators with only two wires. With
Eagle's Global Inputs you can now connect accessories
to the master or slave operator.
EAG2001HP
29-1/2” H. x 22-1/2” W. x 17” D.
Specifications
Specifications
UL 325 & UL 991 Compliant, ETL Listed
UL 325 & UL 991 Compliant, ETL Listed
Limited Warranty
Full 7 Year Residential, 5 Year Commercial
Limited Warranty
Full 7 Year Residential, 5 Year Commercial
Motor
1/2 HP Continuous Duty AC
Motor
1 HP Continuous Duty AC
Duty Cycle
Continuous
Duty Cycle
Continuous
Power Options
115V AC @ 60 Hz 5.7 amp
Power Options
115V AC @ 60 Hz 10.5 amp
Cover
Molded Plastic - Weather Proof - Access Door
Cover
Molded Plastic - Weather Proof - Access Door
Maximum Gate Length
20 Feet
Maximum Gate Length
20 Feet
Maximum Gate Weight
1/2 HP Motor: 750 lbs.
Maximum Gate Weight
1 HP Motor: 1000 lbs.
Gate Speed
18 seconds to open at 90 degrees
Gate Speed
18 seconds to open at 90 degrees
Operator Weight
150 lbs.
Operator Weight
175 lbs.
Drive Chain
#50 Chain Nickel Plated
Drive Chain
#50 Chain Nickel Plated
Emergency Release Options Quick Release Lever
Emergency Release Options Quick Release Lever
Battery Backup
Battery Backup
No - (Optional Power I Battery Backup 40-80 Cycles)
Eagle-200 Commercial Grade
Swing Gate Operator
1/2 HP ~ 600 lbs
The Eagle-100 Residential Swing Gate Operator comes standard with the features you most
often need. Establish full communication
between master and slave operators with only
two wires. With Eagle's Global Inputs you can
now connect accessories to the master or
slave operator. Operation of dual leaf swinging
gates has never been easier.
With three models to choose from, Eagle-200 is the reliable choice for all your commercial and industrial
needs; big heavy gates with high traffic use and smooth
powerful operation. The Eagle-200 Commercial Swing
Gate Operator comes standard with the features you
most often need. Establish full communication between
master and slave operators with only two wires. With
Eagle's Global Inputs you can now connect accessories
to the master or slave operator.
EAG200DM
UL325
UL991
Compliant
No - (Optional Power 2 Battery Backup 40-80 Cycles)
Eagle-100 Residential Single Family Homes
Swing Gate Operator
Dual 1/2 HP ~ 750 lbs (One Motor to Open - One to Close)
29-1/2” H. x 22-1/2” W. x 17” D.
UL325
UL991
Compliant
28” H. x 18” W. x 15” D.
EAG100
Specifications
Specifications
UL 325 & UL 991 Compliant, ETL Listed
UL 325 & UL 991 Compliant, ETL Listed
Limited Warranty
Full 7 Year Residential, 5 Year Commercial
Limited Warranty
Full 5 Year Residential
Motor
1/2 HP Continuous Duty AC
Motor
1/2 HP Continuous Duty AC
Duty Cycle
Continuous
Duty Cycle
Continuous
Power Options
115V AC @ 60 Hz 5.7 amp
Power Options
115V AC @ 60 Hz 5.7 amp
Cover
Molded Plastic - Weather Proof - Access Door
Cover
Molded Plastic - Weather Proof - Access Door
Maximum Gate Length
20 Feet
Maximum Gate Length
18 Feet
Maximum Gate Weight
Dual 1/2 HP Motor: 750 lbs.
Maximum Gate Weight
1/2 HP Motor: 600 lbs.
Gate Speed
18 seconds to open at 90 degrees
Gate Speed
18 seconds to open at 90 degrees
Operator Weight
175 lbs.
Operator Weight
125 lbs.
Drive Chain
#50 Chain Nickel Plated
Drive Chain
#50 Chain Nickel Plated
Emergency Release Options Quick Release Lever
Emergency Release Options Quick Release Lever
Battery Backup
Battery Backup
No - (Optional Power I Battery Backup 40-80 Cycles)
UL325
UL991
Compliant
No - (Optional Power I Battery Backup 40-80 Cycles)
Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com