Meeletronics Venture AF52 User manual

STEREO WIRELESS
BLUETOOTH HEADPHONES
model: AF52
USER MANUAL
part of the
series
EN
TABLE OF CONTENTS
Product Overview
Charging
Powering On and Off
Pairing with Bluetooth® Devices
iPhone®, iPad®, and iPod touch®
Android™ Phones and Tablets
Computers and Laptops
Connecting to Paired Devices
Using the Venture Headphones
Adjusting Volume
Controlling Phone Calls
Controlling Media Playback
Additional Functionality
Using as a Wired Headphone
Safety and Care
Specifications
Troubleshooting
MEElectronics and its logo are registered trademarks of S2E, Inc. All rights reserved.
iPhone®, iPad®, iPod touch® is a registered trademark of Apple Inc.
Android™ is a registered trademark of Google Inc.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.
and any use of such marks by MEElectronics is under license. Other trademarks and trade names are those of
their respective owners.
1
2
2
3
3
3
3
4
4
4
5
5
6
6
6
6
6
PRODUCT OVERVIEW
EN
1
EN
CHARGING
*** You must completely charge the headset
before the first use ***
Connect the mini USB charging cable to any powered USB port and to the
mini USB jack on the right ear cup. The bright red LED indicator will light solid
while charging. Charge time is typically 3-6 hours for the first charge and 2-3
hours for subsequent charges. When the battery is fully charged the bright red
LED indicator will turn off.
Note: Bluetooth will function when the unit is charging, but leaving the Venture
on can increase charge time. The headphones can also be turned off and
used with the included audio cable while charging. This will not affect charge
time.
When the battery is low, the Venture will produce 4 short tones and two red
LED flashes every 20 seconds
TURNING ON AND OFF
a) To turn on, press and hold the Power button for approximately 3 seconds.
The Venture will say “power on” and the blue indicator light will flash 2
times.
b) To turn off, press and hold the Power button for approximately 4 seconds.
When turning off, the Venture will say “power off” and the red indicator
light will flash 2 times.
2
PAIRING WITH BLUETOOTH® DEVICES
EN
*** It is only necessary to pair your Venture once
with each device ***
a) Open the Bluetooth menu* on the device you wish to pair and “search for”
or “add” new devices.
b) Make sure the Venture is off and within 1 meter of your device.
Initiate pairing mode by pressing the power button for 7 seconds, until
you hear “pairing.” The LED light on the venture will flash red and blue in
an alternating manner. (Note: The Venture will enter standby mode if not
paired within 2 minutes.)
c) Wait until you see “Air-Fi Venture” appear on your device
d) Select “Air-Fi Venture” on your device and allow to pair. If your device
asks for a pin, enter “0000”. Once pairing is complete and a connection is
established, the red indicator light will flash 8 times.
If pairing fails, please repeat steps a) through d) above
*Locating the Bluetooth menu:
iPhone, iPad, and iPod Touch
a) On your device, go to Settings
b) Select Bluetooth (Bluetooth is under the General menu in iOS 5.1.1 and
older); if Bluetooth is not on, turn it on. The iPhone/iPad/iPod will
automatically search for new devices
Android Phones and Tablets
a) On your device, go to Settings menu
b) Select Wireless & Networks
Bluetooth Settings and if Bluetooth is not on,
turn it on. Select “Search for Devices” if your phone or tablet does not
automatically search for new devices
Computers and Laptops
Visit www.meelec.com/bluetooth for pairing, connecting, and audio device
setup for computers.
If pairing fails after several tries, please refer to your device’s user manual for
further information.
3
EN
CONNECTING TO PAIRED DEVICES
*** The Venture must have been previously paired
with your device before you can connect ***
When the Venture is turned on and not in pairing mode, it should
automatically connect to last connected device. If the last connected device
is not available, the Venture will connect to other paired devices in the order
of last connection.
If the Venture does not connect and remains in standby mode, a short press
of the Play/Pause button will connect to the last connected device with
Bluetooth on and within range.
Notes: On some PC and Mac computers you will need to manually enable
Bluetooth audio every time you connect
USING THE VENTURE HEADPHONES
Adjusting Volume
Status
Action
Operation
Notes
No media
playing
N/A
The Venture volume
cannot be adjusted
when media is not
playing
N/A
Media
playing
Increase
volume
Single press or press
and hold the Volume
Up
button
Decrease
volume
Single press or press
and hold the Volume
Down
button
Volume will adjust on the Venture;
the connected device volume is
independent. If the volume is not
loud enough or too loud, adjust the
volume on your device and the
Venture. When connected to some
computers the volume will be
controlled only on the Venture.
Increase
volume
Single press Volume
Up
button
Decrease
volume
Single press Volume
Down
button
During a
phone call
Volume adjustments change the
volume on the device, not the
Venture.
Note: When the volume reaches the minimum or maximum level there will be
two short tones.
4
USING THE VENTURE HEADPHONES (Continued)
EN
Controlling Phone Calls
Status
Incoming
call
Call in progress,
phone handset active1
One call active,
one on hold
1
Answer a call
Single press the Power
Mute/Hold or
Cancel mute/hold
Press and hold the Power
until you hear a long tone
Press and hold the Power
until you hear a long tone
Reject a call
Call in progress
Call in progress,
second incoming call
Operation
Function
End a call
Answer new call and
end current call
button
button
Single press the Power
button
Single press the Power
button
Single press the Power
Switch from phone
handset to Venture
button
button
Answer new call and
place the current call
on hold
Press and hold the Power
until you hear a long tone
End current call and
switch to call on hold
Single press the Power
Switch to call on hold Press and hold the Power
until you hear a long tone
button
button
button
If you answer a call from your phone instead of the headset, most phones will activate
the phone handset, not the Venture
Controlling Media Playback
Status
Function
Operation
No media playing1
Play media
Press the Play/Pause
Either media
playing or stopped2
Skip to next track
Press the Next
Restart the
track/previous track
Press the Previous
Media playing
1
2
Pause media playback Press the Play/Pause
Fast forward the track
Rewind the track
button
button
button
Press and hold the Next
button
button
Press and hold the Previous
button
You may need to bring your media app to the screen for the Venture controls to work
Not all media players support this functionality.
Note: If you answer or make a call while listening to media, the media will be
paused until the call has ended.
5
EN
USING THE VENTURE HEADPHONES (Continued)
Additional Functionality
Note: When the volume reaches the minimum or maximum level there will
be two short tones.
Action / Status
Activate voice
command / dialing
Redial last phone
number
Button Function
Single press the Power
Press and hold the Power
until you hear a long tone
button
button
Sounds
Short tone
Long tone when redial is
initiated
USING AS A WIRED HEADPHONE
The Venture comes with a 3.5mm audio jack on the left ear cup and an
audio cable for wired use. This allows use with in-flight entertainment devices,
devices that don’t have Bluetooth or aren’t paired, or when the battery is
depleted.
The Venture can be used wired while still connected via Bluetooth to another
device. Bluetooth audio takes precedence over wired audio; if a Bluetooth
device is connected while listening to wired audio, wired audio will partially
mute when any audio is transmitted via Bluetooth. Wired audio will resume
approximately 20 seconds after the Bluetooth transmission ends.
SAFETY AND CARE
a) When not in use, power the headphones off and store in the included
protective pouch.
b) Clean with a soft cloth, damp with diluted soap water solution if
necessary. Never use chemical cleaners.
c) There are no user replaceable/reparable parts in the headset.
Disassembling it will void your warranty.
d) Do not expose the headphones to liquids. If submersed in water, do not
turn the device on until completely dried.
Note: liquid submersion voids the warranty.
e) Battery performance will be severely decreased when stored in extreme
temperatures: below -10°C/14°F or above 45°C/113°F.
SPECIFICATIONS
See the Air-Fi Venture product page at www.meelec.com for product
specifications.
TROUBLESHOOTING
Please visit www.meelec.com/bluetooth for the troubleshooting information
6
www.meelec.com