Uniden XDECT 8105WP Owner`s manual

XDECT 8105WP
Waterproof Accessory Handset
For more exciting new products please visit our website:
Australia: www.uniden.com.au
New Zealand: www.uniden.co.nz
1
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury to
persons, including the following:
• The charger is NOT waterproof: Do not use or place the charger near
water (e.g., near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool).
• If the charger falls into the water, unplug the AC adaptor before removing it
from the water.
• Wipe excess water off the handset before returning it to the charger.
• Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
• Do not use the telephone to report a gas leak in the vicinity of the leak.
• Use only the power cord and batteries indicated in this manual. Do not
dispose of batteries in a fire. They may explode. Check with local codes for
possible special disposal instructions.
• Do not place the handset in any charging cradle without the battery
installed and the battery cover securely in place.
SAVE THESE INSTRUCTIONS!
Important Notice:
Under power failure conditions this appliance may not operate. Please
ensure that a separate telephone, not dependent on local power, is available
for emergency use.
General Notices for New Zealand Model:
• The grant of a NZ Telepermit for any item of terminal equipment indicates
only that Telecom has accepted that the item complies with minimum
conditions for connection to its network. It indicates no endorsement of the
product by Telecom, nor does it provide any sort of warranty. Above all, it
provides no assurance that any item will work correctly in all respects with
another item of Telepermitted equipment of a differentmake or model, nor
does it imply that any product is compatiblewith all of Telecom’s network
services.
• The maximum volume setting of this telephone exceeds the Telecom
specified volume requirement. Telecom takes no responsibility for the
high volume available on this telephone, who believe this telephone is too
loud should contact the manufacturer at the website indicated on owner’s
manual warranty page.
• For telephone networks other than Telecom there may be a charge
incurred for local calls if the Insert 0 feature is on. Turn Insert 0 off.
• This equipment may not provide for the effective hand-over of a call to
another device connected to the same line.
2
xDECT 8105WP
What’s in the Box?
XDECT 8105WP waterproof accessory
handset & water resistent charger
Charger
AC Adaptor
AAD-600S(M)
Not pictured:
- Factory installed rechargeable battery
- Belt clip
If any item is missing or damaged, contact your place of purchase
immediately. Never use damaged products!
Need help? Get answers at our website:
• www.uniden.com.au for Australian model
• www.uniden.co.nz for New Zealand model.
Understanding the Waterproof Handset
The handset complies with JIS7 water submersion specifications. It
can remain submerged under 1m of water for up to 30 minutes without
damage or loss of functionality. If the handset falls into water, just remove
it; you can continue using the handset as normal.
The handset will still receive calls even if it is under water, but you
probably won’t be able to hear the ringer or the earpiece. To avoid any
accidents, do not try to use the handset while it is still under water.
If you notice that the sound is distorted after your handset is submerged
in water, there might still be water around the speaker and microphone.
Just shake the handset to clear the water, and the sound should return to
normal. Don’t place the handset where it will be subjected to direct
sunlight for long periods of time.
3
INSTALLING YOUR hANdset
Charge the Battery
The handset’s rechargeable battery is already installed. Before you can
charge the battery, you have to power it on.
1. Remove the cardboard spacer.
2. Press the power on/off (activation) pin according to the directions on
the label.
3. Remove the label once the handset is powered on.
Save the power on/off pin in case you need to change the
handset’s power status later (i.e., to power off the handset when
it will not be used for a long time). Use the plastic power on/off
pin or a blunt-tipped object like an uncurled paper clip to press
the power on/off toggle through the rubber seal. Do not use a
sharp object; sharp objects might puncture the rubber seal and
jeopardize the handset’s waterproof status.
4. Connect the AC adaptor to the charger’s DC IN 9V jack and set the
cord into the notch. (This adaptor might already be connected.)
5. Plug the other end of the adaptor into a standard 240V AC power
outlet.
6. Place the handset in the charger with the display facing forward. The
display on the handset should turn on.
If..
Try..
the handset display does not
turn on
• Checking the AC adaptor
connection.
• Seeing if the outlet is controlled
by a wall switch.
##Charge the Handset completely (16 hours) before using it.
4
Installing the Beltclip
Line up the holes on each side of the handset.
To attach the belt clip; Insert into the holes on each side of the handset.
Press down until it clicks.
To remove the belt clip; Pull either side of the belt clip to release the
tabs from the holes.
registering to a base
The accessory handset won’t work until you register it to a
compatible Uniden cordless phone!
Compatible Bases
This handset is designed for use with Uniden’s XDECT 8115 and XDECT
8155 bases.
Other compatible bases include Uniden’s XDECT6135, SSE35/37 and
DECT31xx series.
Some features may not be available when using the XDECT 8105WP
with these other bases. For the most up-to-date list of which bases this
handset is compatible with, see our website.
Registration Methods
There are two different registration methods, but it’s easy to figure out
which one applies to your handset and base. Answer question to register
the handset to one of the compatible bases.
Does the base have an LCD display?
Yes
1. On the base, open the menu and select Register Accy. The
display should show Registering.
2. On the handset, press and hold HASH(#) until the display says
Handset Registering (about 2 seconds).
No
1. On the base, press and hold FIND about 5 seconds in
standby mode.
2. On the handset, press and hold HASH(#) until the display
says Handset Registering (about 2 seconds).
##After about 30 seconds, the handset display should say Registration
Complete.
5
Test the Connection
Pick up the handset and press TALK/FLASH. Make sure you get a dial
tone. (Press END to hang up.)
If..
Try..
• you don’t hear a dial tone
• the display shows
Registration Failed
Making sure the handset is fully
charged, before trying again.
resetting the handset
If you are having trouble with a handset or if you want to replace one, you
need to clear the registration information from the base and the handset:
Do you have the base the HS is registered to?
Yes
1. Press & hold END and # until
the System Reset menu
appears (about 5 seconds).
2. Select Deregister HS. The
display lists all registered
handsets.
3. Select the HS you want to
reset.
4. When the phone asks you to
confirm, select Yes. The HS
clears its information from the
base & deletes its own link to
the base.
No
1. Press & hold END and # until
the System Reset menu
appears (about 5 seconds).
2. Select Base Unavailable.
3. When the phone asks you
to confirm, select Yes. The
handset deletes its own link
without contacting the base.
When you reset a handset (or if you buy a new one), that handset
displays a Handset Not Registered message. If you see this message
on a handset, you need to register it to a base before you can use it.
6
IMPORTANT INFORMATION
• As the handset adapts to the base, the exact features and operation of
the handset will vary slightly depending on which base you register the
handset to. Refer to the owner’s manual for the base you’re registering
the handset to for feature descriptions.
• All features and operation for the handset are described in the owner’s
manual for one of the bases listed under the Compatible Bases
section.
• Owner’s manuals for all Uniden phones are available on our website
for free downloading.
AC Adaptor
Parts Number
AAD-600S(M)
Input Voltage
Output Voltage
100-240V AC, 50/60Hz
9V DC @ 210mA
Battery Information
Type
BT-694
Capacity
650mAh
Talk time
about 12 hours
Standby Time
about 12 days
• Use only the supplied AC adaptors.
• Be sure to use the proper adapter for the base and any chargers.
• Do not place the power cord where it creates a trip hazard or where it
could become chafed & create a fire or electrical hazard.
• Do not place the unit in direct sunlight or subject it to high
temperatures.
• Fully charged, the battery should provide about 12 hours of talk time
and about 12 days of standby time. For best results, return the handset
to the cradle after each call to keep it fully charged.
• Keep an eye on the battery status icon. When the battery gets too
low, the handset shows a low battery alert. If you hear a strange beep
during a call, check the display: if you see the low battery alert, finish
your conversation as quickly as possible and return the handset to the
cradle. If the handset is in standby, none of the keys will operate.
• With normal use, the battery should last about one year. Replace the
battery when the talk time becomes short even when the battery is
charged. To buy a replacement battery, visit the website.
7
Rechargeable Nickel-Metal-Hydride Battery Warning
CAUTION! Risk of explosion if battery is replaced by an incorrect type!
Dispose of used batteries according to the instructions. Do not open or
mutilate the battery. Disconnect the battery before shipping this product.
• This equipment contains a rechargeable Nickel-Metal-Hydride
(Ni-MH) battery.
• Do not short-circuit the battery.
• The rechargeable batery contained in this equipment may explode if
disposed in a fire.
• Do not charge the battery used in this equipment in any charger
other than the one designed to charge this battery as specified in the
owner’s manual. Using another charger may damage the battery or
cause it to explode.
Rechargeable batteries must be recycled or disposed of properly. Uniden
works to reduce lead content in PVC coated cords in our products &
accessories.
8
9
10
one-year limited warranty
XDECT 8105WP
Important:
Satisfactory evidence of the original purchase is required for warranty
service. Please refer to our Uniden website for any details or warranty
durations offered in addition to those contained below.
Warrantor:
The warrantor is either Uniden Australia Pty Limited ABN 58 001 865 498
(“Uniden Aust”) or Uniden New Zealand Limited (“Uniden NZ”) as the
case may be.
Terms of Warranty: Uniden Aust/NZ warrants to the original retail
purchaser only that the XDECT 8105WP (“the Product”), will be free
from defects in materials and craftsmanship for the duration of the
warranty period, subject to the limitations and exclusions set out below.
Warranty Period: This warranty to the original retail purchaser is only
valid in the original country of purchase for a Product first purchased
either in Australia or New Zealand and will expire one (1) year from the
date of the original retail sale. If a warranty claim is made, this warranty
will not apply if the Product is found by Uniden to be:
A.Damaged or not maintained in a reasonable manner or as recommended
in the relevant Uniden Owner’s Manual;
B.Modified, altered or used as part of any conversion kits, subassemblies
or any configurations not sold by Uniden Aust or Uniden NZ;
C.Improperly installed contrary to instructions contained in the relevant
Owner’s Manual
D.Repaired by someone other than an authorized Uniden Repair Agent in
relation to a defect or malfunction covered by this warranty; or
E.Used in conjunction with any equipment, parts or a system not
manufactured by Uniden.
Parts Covered: This warranty covers the Product and included
accessories.
User-generated Data: This warranty does not cover any claimed loss of
or damage to user-generated data (including but without limitation phone
numbers, addresses and images)that may be stored on your Product.
11
Statement of Remedy: If the Product is found not to conform to this
warranty as stated above, the Warrantor, at its discretion, will either
repair the defect or replace the Product without any charge for parts or
service. This warranty does not include any reimbursement or payment
of any consequential damages claimed to arise from a Product’s failure to
comply with the warranty. Our goods come with guarantees that cannot
be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and
the failure does not amount to a major failure. This warranty is in addition
to and sits alongside your rights under either the COMPETITION AND
CONSUMER ACT 2010 (Australia) or the CONSUMER GUARANTEES
ACT (New Zealand) as the case may be, none of which can be excluded.
Procedure for Obtaining Warranty Service: Depending on the
country in which the Product was first purchased, if you believe that
your Product does not conform with this warranty, you should deliver
the Product, together with satisfactory evidence of your original
purchase (such as a legible copy of the sales docket) to Uniden at the
addresses shown below. You should contact Uniden regarding any
compensation that may be payable for your expenses incurred in making
a warranty claim. Prior to delivery, we recommend that you make a
backup copy of any phone numbers, images or other data stored on
your Product, in case it is lost or damaged during warranty service.
UNIDEN AUSTRALIA PTY LTD
Service Division
345 Princes Highway,
Rockdale, NSW 2216
Phone number: 1300 366 895
Email: custservice@uniden.com.au
UNIDEN NEW ZEALAND LTD
Service Division
150 Harris Road, East Tamaki
Auckland 2013
Phone number: (09) 273 8377
Email: service@uniden.co.nz
2014 Uniden Australia Pty Ltd/Uniden New Zealand Ltd
©2012
Printed in Vietnam U01UU299BZZ(0)
U01UU282BZZ(0)
12