Verizon JetPack 890L User guide

Verizon Jetpack™
4G LTE Mobile Hotspot - 890L
USER
GUIDE
USER GUIDE
105 mm
XXXX0000000(0.0) X
75 mm
Verizon Jetpack™
4G LTE Mobile Hotspot
Model#: 890L
Global Ready™
10 mm
Job Number
Project
100035015 In Box Collateral
Client
Inks
Verizon
Rev No.
File Name
UG_EuFi890_CVR_75x105_NHS_V0_R2.ai
0
Description
Date
11/02/11
Produced By
75 x 105 User Guide
Mary Salazar
THIS FILE MAY CONTAIN IMAGES OR ILLUSTRATIONS THAT ARE COPYRIGHT PROTECTED. CLIENT MUST OBTAIN PROPER LICENSING AND USAGE RIGHTS PRIOR TO REPRODUCTION.
SUPPLIER IS RESPONSIBLE FOR CHECKING WORKING DRAWINGS BEFORE PLATES ARE MADE FOR ACCURACY IN MEASUREMENTS, PLATE TOLERANCE REQUIREMENTS,
REGISTRATION AND CONSTRUCTION DETAILING. ANY CHANGES MADE TO SUIT PRODUCTION REQUIREMENTS SHOULD BE APPROVED BY BOTH THE CLIENT AND DESIGN DIRECTOR.
ALL COPY SHOULD BE PROOFREAD BY CLIENT AND LEGAL REQUIREMENTS CHECKED BY CLIENT’S LEGAL DEPARTMENT.
Designer
Production
Proofreader
PROCESS
CYAN
PROCESS
MAGENTA
PROCESS
YELLOW
PROCESS
BLACK
Finishes
Client Services
NOTES: VARNISH LAYER HAS BEEN PROVIDED IN THIS FILE.
PROCESS COLOR VALUES ARE BASED ON ARTWORK PROVIDED AND HAVE NOT
BEEN ALTERED.
MATTE
VARNISH
This Proof Indicates Approximate Color Only. For Accurate Color Match, Use Approved Color Standard.
DO NOT USE COLOR FORMULAS ON THIS FILE.
LEGAL INFORMATION
Copyright © 2012 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted,
reproduced, translated or utilized in any form or
by any means, electronic or mechanical, including
photocopying and microfilm, without the prior
written permission of ZTE Corporation.
The manual is published by ZTE Corporation. We
reserve the right to make modifications on print
errors or update specifications without prior
notice.
Version No. : 1.0
Edition Time : 03-2012
1
CONTENTS
Welcome..................................................................... 4
Thank You for Choosing Verizon Wireless.......... 4
Getting Started....................................................... 5
Screen Indicators........................................................ 6
Hardware Installation............................................ 8
Installing the 4G SIM Card....................................... 8
Inserting and Charging the Battery....................... 9
Removing the 4G SIM Card....................................11
Connecting to the Internet............................... 12
Connecting Wi-Fi Enabled Devices To Your
Jetpack..........................................................................12
Follow these Steps....................................................13
Accessing the Internet............................................13
Advanced Configuration.................................... 14
PIN Code Verification...............................................15
Basic Setup..................................................................16
WAN Settings..............................................................17
Router............................................................................20
Wi-Fi Settings.............................................................21
Firewall..........................................................................26
SMS................................................................................31
2
Navigating the Device........................................ 32
WAN Info.......................................................................33
WLAN Info....................................................................33
Settings.........................................................................34
Message........................................................................36
Usage of WPS........................................................ 36
Glossary................................................................... 37
How to Get Help.................................................... 41
Health and Safety Information....................... 41
General Guidelines....................................................41
Aircraft Safety...........................................................46
Hospital Safety..........................................................47
Road Safety.................................................................47
Vehicles Equipped with an Airbag.......................48
Third Party Equipment.............................................48
Efficient Use...............................................................49
CTIA Requirements...................................................49
Radio Frequency (RF) Exposure ..........................50
FCC Compliance.........................................................52
Consumer Limited Warranty............................ 55
3
Welcome
Thank You for Choosing Verizon Wireless
You’re now connected to the blazingly fast,
powerfully brilliant Verizon 4G LTE Network. This
guide will help you understand your new mobile
hotspot and all the things you can do with it at
home or abroad. So let’s get started.
This guide will show you how to unleash the
potential of your new Verizon Jetpack™. Assistance
is at your fingertips at verizonwireless.com/
support. Customer Service is at your disposal
at 1-800-922-0204 or in any Verizon Wireless
Communications Store.
Device Introduction
The Verizon Jetpack™ - 890L is a newly developed
4G LTE Mobile Hotspot. It is Global Ready™
providing flexible access for users to enjoy
high-speed internet applications around the
globe. When connected to the Verizon 4G LTE
Network, the Jetpack can support simultaneous
connections to up to 10 Wi-Fi enabled devices.
When connected in 2G or 3G mode the Jetpack
can support simultaneous connections to 5 Wi-Fi
enabled devices.
4
Getting Started
5
6
1
4
3
2
BUTTONS AND
INTERFACE
7
DESCRIPTION
1. SCREEN
Displays the menus and the
status of your Jetpack.
2. UP BUTTON
Scroll up to select the
options.
3. DOWN BUTTON
Scroll down to select the
options.
5
Confirm highlighted
selection.
4. OK BUTTON
5. POWER SWITCH
When the Jetpack button
is locked, press once to
light up the screen, and
press again to unlock.
Power on/off your Jetpack.
6. MICRO USB PORT Charge your Jetpack.
7. RESET BUTTON
Press and hold to restore
your Jetpack to the factory
default settings.
Screen Indicators
Icon
Description
Battery Status
4G Network
3G Network
2G Network
Data Connected
6
Icon
Description
Signal Strength
and
No Network Service
Roaming Signal Strength
Roaming
SMS
New SMS
SMS Full
Number of current Wi-Fi
connections
Settings
7
Hardware Installation
Installing the 4G SIM Card
If you have not already done so, please follow
these instructions for the installation of your new
4G SIM Card:
1. Remove 4G SIM Card from the outer card,
being careful not to touch the gold contacts.
CAUTION: Do not bend or scratch your 4G SIM
Card. Avoid exposing your 4G SIM Card to static
electricity, water or dirt.
2. Turn the power off. Remove the battery cover
and take the battery out. Locate the 4G
SIM card slot. Hold the card so the Verizon
Wireless logo on the card is facing you and the
gold contact points are properly aligned with
the 4G SIM Card slot.
3. Insert 4G SIM Card with the Verizon Wireless
logo facing you into the slot until it is fully
inserted.
8
NOTE: Your 4G SIM (Subscriber Identity Module)
Card is a small rectangular plastic card that stores
your phone number and important information
about your wireless service.
The 4G SIM Card MUST remain in the Jetpack
when in use.
Inserting and Charging the Battery
1. Use the thumb catch at the bottom of the
device to open the battery cover and align
the battery contacts with the terminals in
the battery compartment as shown. Push the
battery down until it clicks into place.
2. Place the battery cover over the battery
compartment ensuring that the arrow on
the device and the arrow on battery cover
are aligned. Then press the battery cover
downward until it clicks into place.
9
Your device comes with wall charger. To charge:
1. Plug one end of the wall charger into an
electrical outlet and the the other end into the
device’s MICRO USB PORT.
2. It is recommended the battery be fully charged
before you use your Jetpack for the first time.
NOTE: The charge time varies depending upon the
battery level. The device will stop charging if the
temperature of the battery exceeds 113 °F/45 °C.
10
Removing the 4G SIM Card
1. Turn the Verizon Jetpack power off. Remove
the battery cover and take out the battery.
2. Gently remove the SIM Card from the SIM Card
slot.
NOTE: Should your 4G SIM Card be lost or
damaged please call 1-800-922-0204 to speak
with a Customer Service Representative. From
outside the U.S. call + 1-908-559-4899 for 24/7
Global Support.
You can move the 4G SIM Card from one device
to another and your wireless service will work
seamlessly as long as you have a compatible
device and service plan. To see which devices are
compatible with the Verizon Wireless 4G SIM
Card, visit verizonwireless.com/certifieddevice.
For additional information about 4G SIM Cards,
visit verizonwireless.com/4GSIM.
11
Connecting to the Internet
With your new Verizon Jetpack, a wireless Internet
connection can always be at your fingertips.
Connecting Wi-Fi Enabled Devices To Your
Jetpack
NOTE: It is recommended the battery be fully
charged in order to use your Jetpack via Wi-Fi for
the first time, or connect your Jetpack to the wall
adapter for power.
The following should occur once you power on your
Jetpack:
 Your Jetpack is powered as soon as you slide
the Power Switch to On and the display lights
up.
 Once your Jetpack is powered on and has
been activated, it automatically connects to
the Internet provided that Mobile Broadband
service is available and one or more Wi-Fi
devices are connected to the Jetpack.
 The Service(4G LTE, 3G, 2G), Signal Strength
, and Data Connected
icons on your
Jetpack indicate it is in service and ready to
connect.
12
Follow these Steps
1. Ensure the Wi-Fi enabled device you wish to
connect to yourJetpack has Wi-Fi turned on,
then use the Wi-Fi application toestablish a
connection to your Jetpack.
2. Look for the network (SSID) named “Verizon890L”. There are XXXX digits unique to your
device following the network (SSID) name
displayed.
3. Click Connect and enter the default password
printed on the back of your Jetpack .
NOTE: Your password will also be displayed on the
Jetpack screen each time the Jetpack is powered
on.
Accessing the Internet
After successfully establishing the connection
between your Jetpack and computer, you can
access the Internet in the Auto Connect, Manual
Connect mode. The default mode is Auto Connect.
13
Advanced Configuration
1. Make sure your computer is connected to the
Jetpack .
2. Launch the internet browser and enter
http://192.168.1.1 or http://vz.hotspot in
the address bar.
NOTE: It is recommended that you use IE (7.0 or
later), Firefox (3.0 or later), Opera (10.0 or later),
Safari (4.0 or later) or Chrome (5.0 or later).
3. The login page appears as follows:
Input the case-sensitive default password printed
on the back of your Jetpack, and then click Login
to access the Web User Interface.
NOTE: Do not put anything on the top of your
Jetpack. Do not lay devices to overlap each other
when using.The Jetpack takes 1~2 minutes to
initialize, and attach to the network.
14
PIN Code Verification
If the PIN code of your SIM card is enabled, you
will need to input the PIN code after you logging in.
NOTE: The SIM card will be locked if you enter
wrong PIN code consecutively for three times.
If you want to change the PIN status or modify the
PIN code, please select WAN Settings > SIM PIN to
do the actions.
15
Basic Setup
After logging in, select Basic Setup > Quick Setup
to configure the Wi-Fi settings, including Wi-Fi
Network Name, Wi-Fi Securiy Policy and Sleep
Time.
Select Basic Setup > Password to change the login
password for the Web User Interface.
16
WAN Settings
After logging in, select WAN Settings > Wireless
Info to display the infomation of WAN wireless.
Click Refresh to update the information.
Select WAN Settings > Network Select to select
the proper network mode, including Global Mode,
LTE/CDMA Mode, and GSM Mode(Automatic/
Manual). Click Apply to comfirm your choice.
17
NOTE: In GSM Mode, you can either set your device
to automatic network selection or manual network
selection. If you choose the manual, you will be
prompted to select what GSM network you would
like to connect to.
18
Select WAN Settings > WAN Connection to choose
the WAN Connection mode according to your
requirement.
Auto Connect: The device will connect to the
Internet automatically when it is powered on.
Manual Connect: Connect/disconnect to the
Internet connection manually.
Select WAN Settings > SIM PIN to enable/disable/
modify the PIN code of your SIM card.
19
Router
After logging in, select Router > LAN to access the
interface below:
IP Address: IP address for LAN interface.
Subnet Mask: Subnet mask for the IP address.
MAC Address: MAC address for the LAN interface.
DHCP Server: Enable/disable DHCP server
function.
DHCP IP Pool: Allocate start and end IP address
for IP pool.
Select Router > DMZ to access the interface
below:
20
DMZ means demilitarized zone, click Add to add
the Wi-Fi client in DMZ, and click Apply to confirm.
Click Delete to erase the Wi-Fi client from DMZ.
An external computer or device can access to the
Wi-Fi client which is in DMZ, rather than any other
part of the network.
Wi-Fi Settings
After logging in, select Wi-Fi Settings > Connected
Devices to display the information about the
devices connected to your Jetpack.
You can click Refresh to update the information,
or click Disconnect to terminate the wireless
connection between these Wi-Fi enabled devices
and your Jetpack.
Select Wi-Fi Settings > Basic to set the
configuration of the wireless network.
21
Sleep Time: Set the time before the Jetpack
enters sleep mode, The Jetpack will enter sleep
mode if no Wi-Fi clients (devices) are connected to
the Jetpack for a given period of time.
Network Mode: If all of the wireless devices
connect with the Jetpack in the same transmission
mode, performance will be improved by choosing
the appropriate wireless mode.
SSID: Service Set Identifier(SSID). Enter a string
less than 30 characters as the name for your
wireless local area network(WLAN).
Broadcast SSID: Disable or Enable(Default)
this function. If Enable is selected, the Jetpack
broadcasts the SSID, and other devices can search
and connect to it. When you select Disable, other
devices can not search out the SSID. If you want
someone to connect, you need tell them the SSID,
and let them to setup manually.
22
AP Isolation: When Enable is selected, each of your
wireless clients will not be able to communicate
with each other.
Country Code: Choose the right country code.
Frequency(Channel): Choose the appropriate
channel to optimize the performance and coverage
of your wireless network.
MAX Connections: Choose the maximum number
of the Wi-Fi enabled devices which are able to
connect to the Jetpack simultaneously.
Click Apply to save your settings.
Select Wi-Fi Settings > Security to set the Wi-Fi
security settings.
23
The security modes are described below:
NONE: In this mode, no password is required.
WEP: The WLAN clients who have the same key
with wireless gateway can pass the authentication
and access the wireless network.
WPA-PSK: WPA Pre-Shared Key, Enter the PreShared key as a plain text (ASCII) pass-phrase of
at least 8 characters.
WPA2-PSK: A securer version of WPA with
implementation of the 802.11i standard.
WPA-PSK/WPA2-PSK: Apply both the WPA-PSK
and WPA2-PSK scheme.
If the Security type is WEP, the following
configuration page will appear:
Authentication Type: Two types of authentication
can be used: OPEN and SHARE. In the OPEN
authentication type, the WLAN client (device)
doesn't need to provide the correct credentials
24
to the Jetpack in order to connect to it. However,
if the credentials are incorrect, data won't be
transferred successfully between the WLAN
clients and Jetpack. In effect, no authentication
occurs. And in the SHARE authentication type, the
WLAN client cannot connect to the Jetpack with
the incorrect crendentials.
Encrypt Type: Select the encrypt type(WEP-40
and WEP-104).
Password: You can set at most four keys. Choose
one of them as the default key, which is the only
key in use at any given time. You must enter the
default keys on the Wi-Fi client in order to connect
to the Jetpack.
Select Wi-Fi Settings > ACL to access:
25
If the ACL(Access Control List) policy is Deny, the
user in MAC list can't connect to this device. If
the ACL policy is Accept, the user in MAC list can
connect to this device. You can allow or refuse a
Wi-Fi user according to different ACL policy.
Select Wi-Fi Settings > Firmware to display the
Wlan Chip Firmware Version.
Firewall
After logging in, select Firewall > IP/Port Filtering
to access:
If you select Enable, the filter settings will appear:
26
Default Policy: Set how to handle the packet if any
of the rules matches.
Source IP Address: Set the source IP address that
will be filtered.
Source Submask: Set the source submask that will
be filtered.
Protocol: Set which protocol will be used for
filtering.
Source Port Range: Set the source port numbers
that will be filtered.
Dest Port Range: Set the destination port numbers
that will be filtered.
27
How to add a new rule:
1. Select Enable and click Apply in the Basic
Settings area.
2. Input the detail information in the Ip/Port
Filtering area.
3. Click Add in the Ip/Port Filtering area.
In the Current IP/Port filtering rules area, click
Delete to delete the rules that you selected.
Select Firewall > Port Forwarding to access:
If you select Enable, the Virtual Server Settings
will appear:
28
IP Address: Set IP address for the virtual server.
Port: Set port number for the virtual server.
Protocol: Set the protocol for the virtual server.
How to add a virtual server:
1. Select Enable and input the detailed information
in the Virtual Server Settings area.
2. Click Apply to save your settings.
In the Current Virtual Servers area, click Delete to
delete the virtual servers that you selected.
Select Firewall > VPN to enable/disable the VPN
Connection.
Advanced
After logging in, select Advanced > Status to
display the system information.
29
Select Advanced > Statistics to check your WAN
usage. Click Refresh to update the usage, and click
My Verizon to visit Verizon website to check your
monthly total data.
Select Advanced > Restore&Reboot to restart
your device, or restore your device to the factory
default settings.
Select Advanced > Sound Alert to turn on/off the
sound alert.
30
Select Advanced > Config File to import/export
the configuration file of the device.
NOTE: It will modify the configuration of this
device to import configuration file. Please make
sure the parameters in the configuration file are
correct.
SMS
This function allows you to view, save, send and
receive text messages. After logging in, select
Message to perform the related operations.
31
Navigating the Device
Slide the Power Switch to the ON position to
turn on the device. The screen lights up. After the
initialization of the device, the SSID and default
password will display on the screen. Press the OK
button, the following icons will appear:
NOTE: Devices and software are constantly evolving — the screen images and icons displayed are for
reference only and may differ from your device.
When your Jetpack is roaming, it will remind you
that higher charges may be generated if you want
data access while roaming. Select Yes, and then
press the OK button to access the data connection.
Select No, and then press the OK button to refuse.
32
WAN Info
Select
and press the OK button to check the
WAN information. Use the UP and DOWN buttons
to scroll to the desired menu. Press the OK button
to view information about the following WAN
settings:
Network Provider: Displays the name of your
service provider.
Network Type: Displays your network type.
Roam: Displays whether or not your device is
roaming.
WAN Connection: Check your connection status.
WLAN Info
Select
using the UP and DOWN buttons
and press the OK button to check the WLAN
information. Use the UP and DOWN buttons to
scroll to the desired menu. Press the OK button
to view information about the following WLAN
settings:
SSID Information: Displays the SSID and
password.
Connected Device: Displays the information about
connected Wi-Fi devices.
Start WPS: Launch the Wi-Fi Protection Setup.
33
Read the prompt on the display and refer to the
Usage of WPS chapter.
Settings
Select
using the UP and DOWN buttons and
press the OK button to check the settings. Use
the UP and DOWN buttons to scroll to the desired
menu. Press the OK button to view information
about the following settings:
Device Info: Displays the basic information about
your device: Phone Number, SIM ID, MEID, SW
Version and RSSI.
Mobile Network: Use the UP and DOWN buttons
to scroll to the desired menu. Press the OK button
to view the following operations related to your
network:
 Data Connection: Connect or disconnect
the WAN connection.
 Network Select: Choose the desired
network from the following options:
Global Mode, LTE/CDMA Mode, and GSM
Mode .
Wi-Fi: Press the OK button to select Proceed to
adjusting your Wi-Fi settings or Back to return to
the previous menu.
The following Wi-Fi settings appear when you
34
select Proceed:
 Wi-Fi Network Mode: Change the Wi-Fi
standard.(It is recommended that you do
not change the defualt setting, 11 b/g.)
 S S I D B r o a d c a s t : E n a b l e o r d i s a b l e
discovery mode, allowing your device to be
found by other Wi-Fi compatible devices.
 AP Isolation: Enable or Disable the
connection between connected Wi-Fi
devices communicating with each other.
 Channel: Choose the appropriate channel
frequency to optimize the performance
and coverage of your wireless network.
 MAX Connections: Choose the maximum
number of Wi-Fi devices that can be
connected to your device simultaneously.
Web User Interface: Indicates you how to access
the web-based Configuration Page for your device.
Software Update: Select Check New to check for
new software.
Button Lock: Set the lock duration for your device
by selecting on of the following options: 30Secs/
15Secs/Never.
Sound Alert: Mute or unmute the system alert.
35
Message
Select
using the UP and DOWN buttons and
press the OK button to check messages. Select
one of the following options:
New Messages: Displays your unread messages.
Inbox: Displays the messages in your inbox.
Usage of WPS
If your client device supports WPS, you need not
input the password manually after WPS has been
available. Please do the following:
1. Start up your Jetpack.
2. Launch the client device.
3. Select the icon , and then choose Start WPS
to enable the WPS function of your Jetpack.
4. Enable the WPS function of the client.
NOTE: For the detailed operations about the client,
please refer to the client’s instruction.
36
Glossary
3G: Third Generation. 3G refers to the third
generation of mobile telephony technology.
4G: Fourth Generation. 4G refers to the third
generation of mobile telephony technology.
802.11(b, g, n): A set of WLAN communication
standards in the 2.4, 3.6 and 5 GHz frequency
bands.
Broadband: High-capacity high-speed,
transmission channel with a wider bandwidth than
conventional modem lines. Broadband channels
can carry video, voice, and data simultaneously.
DHCP: Dynamic Host Configuration Protocol.
Software found in servers and routers that
automatically assigns temporary IP addresses to
clients logging into an IP network.
DHCP Server: A server or service with a server
that assigns IP addresses.
Firewall: A hardware or software boundary that
protects a network or single computer from
unwanted outside traffic.
Firmware: A computer program embedded in
an electronic device. Firmware usually contains
operating code for the device.
37
Hotspot: A WiFi (802.11) access point or the area
covered by an access point. Used for connecting
to the Internet.
H T T P : H y p e r t e x t Tr a n s f e r P r o t o c o l . A n
application-level protocol for accessing the World
Wide Web over the Internet.
IEEE: Institute of Electrical and Electronics
Engineers. An international technical/professional
society that promotes standardization in technical
disciplines.
LAN: Local Area Network. A type of network that
lets a group of computers, all in close proximity
(such as inside an office building), communicate
with one another. It does not use common carrier
circuits though it can have gateways or bridges to
other public or private networks.
MAC Address: Media Access Control. A number
that uniquely identifies each network hardware
device. MAC addresses are 12-digit hexadecimal
numbers. This is also known as the physical or
hardware address.
Port: A virtual data connection used by programs
to exchange data. It is the endpoint in a logical
connection. The port is specified by the port
number.
38
Port Forwarding: A process that allows remote
devices to connect to a specific computer within a
private LAN.
Port Number: A 16-bit number used by the TCP
and UDP protocols to direct traffic on a TCP/IP
host. Certain port numbers are standard for
common applications.
Protocol: A standard that enables connection,
communication, and data transfer between
computing endpoints.
Router: A device that directs traffic from one
network to another.
SIM: Subscriber Identification Module. Found in
GSM network technology, the SIM is a card
containing identification information for the
subscriber and their account. The SIM card can be
moved to different devices.
SMS: Short Messaging Service. Short text
messages of generally no more than 140-160
characters sent and received by wireless devices.
SSID: Service Set IDentifier. The name assigned to
a WiFi network.
TCP/IP: Transmission Control Protocol/Internet
Protocol. The set of communications protocols
used for the Internet and other similar networks.
39
USB: Universal Serial Bus. A connection type for
computing device peripherals such as a printer,
mobile device, etc.
VPN: Virtual Private Network. A way to
communicate through a dedicated server securely
to a corporate network over the Internet.
WAN: Wide Area Network. A public network that
extends beyond architectural, geographical, or
political boundaries (unlike a LAN, which is usually
a private network located within a room, building,
or other limited area).
WEP: Wired Equivalent Privacy. An IEEE
standard security protocol for 802.11 networks.
Superseded by WPA and WPA2.
Wi-Fi: Wireless Fidelity. Any system that uses the
802.11 standard developed and released in 1997
by the IEEE.
Wi-Fi Client: A wireless device that connects to
the Internet via Wi-Fi.
WPA/WPA2: Wi-Fi Protected Access. A security
protocol for wireless 802.11 networks from the
Wi-Fi Alliance.
40
How to Get Help
Assistance is at your fingertips at verizonwirless.
com. Customer Service is at your disposal at
1-800-922-0204 or in any Verizon Wireless
Communications Store.
If you have questions about how to use ZTE mobile
devices or your device needs repair services,
please access to our support website, contact our
services hotline or email for more information.
Website Address: http://www.zteusa.com/
support/
Service Hotline: 877-817-1759 (9:00 am – 9:00
pm CST)
Service Email: devicesupport@zteusa.com
Health and Safety Information
General Guidelines

Some electronic devices may be susceptible
to electromagnetic interference. Locate the
device away from TV set, radio and other
electronic equipment to avoid electromagnetic
interference.
41









The device may interfere with medical devices
like hearing aids and pacemakers. Consult a
physician or the manufacturer of the medical
device before using the device.
Please keep yourself at least 20 centimeters
away from the device.
Do not use your device in dangerous
environments such as oil terminals or chemical
factories where there are explosive gases or
explosive products being processed.
Please use original accessories or accessories
that are authorized by ZTE. Unauthorized
accessories may affect the device
performance, damage the device or cause
danger to you.
Do not attempt to dismantle the device. There
are no user serviceable parts.
Do not allow the device or accessories to come
into contact with liquid or moisture at any
time. Do not immerse the device in any liquid.
Do not place objects on top of the device. This
may lead to overheating of the device.
The device must be u s e d i n ve n t i l a t e d
environment.
Do not expose the device to direct sunlight
or store it in hot areas. High temperature can
42
shorten the life of electronic devices.
Do not allow children to play with the device or
charger.
 Use an antistatic cloth to clean the device. Do
not use chemical or abrasive cleanser as these
could damage the plastic case. Turn off your
device before you clean it.
 Use the device within the temperature range
of -10°C ~ +35°C, and the storage temperature
range is -20°C ~ +60°C. The humidity range is
5%~90%.
 Do not use your device during a thunderstorm.
Remove the charger from the mains socket.
 D o n o t t a k e o u t y o u r ( U ) S I M c a r d
unnecessarily. The (U)SIM card may be easily
lost or it can be damaged by static electricity.
 Do not place the device alongside computer
disks, credit cards, travel cards or other
magnetic media. The information contained
on the disks or cards may be affected by the
device.
 Do not paint the device.
 Do not remove the device battery while the
device is switched on.
 Take care not to allow metal objects, such as

43







coins or key rings, to contact or short circuit
the battery terminals.
Do not dispose of batteries in fire. The device’
s Li-ION batteries may be safely disposed
of at a Li-ION recycling point. Follow local
requirements for recycling.
Do not put the device’s battery in your mouth,
as battery electrolytes are toxic.
Do not modify or remanufacture, attempt
to insert foreign objects into the battery,
immerse or expose to water or other liquids,
expose to fire, explosion or other hazard.
Only use the battery for the system for which
it is specified.
Only use the battery with a charging system
that has been qualified with the system per
this standard. Use of an unqualified battery or
charger may present a risk of fire, explosion,
leakage, or other hazard.
Do not short circuit a battery or allow metallic
conductive objects to contact battery
terminals.
Replace the battery only with another battery
that has been qualified with the system per
this standard, IEEE-Std-1725-200x. Use of an
44









unqualified battery may present a risk of fire,
explosion, leakage or other hazard.
Promptly dispose of used batteries in
accordance with local regulations.
Battery usage by children should be
supervised.
Avoid dropping the device or battery. If the
device or battery is dropped, especially on a
hard surface, and the user suspects damage,
take it to a service center for inspection.
Improper battery use may result in a fire,
explosion, or other hazard.
Do not put a battery into a microwave oven,
dryer or high-pressure container.
Do not connect the battery directly into an
electric outlet or cigarette lighter charger.
Use only authorized chargers.
Do not puncture the battery with a sharp
object such as a needle.
When the battery is disposed, be sure it is
non-conducting by applying vinyl tape to the (+)
and (-) terminals.
Do not drop, throw, or subject the device to
rough treatment.
45

Stop using the battery if abnormal heat,
odor, discoloration, deformation, or abnormal
condition is detected during use, charge or
storage.
 Do not use your device with a damaged or
deformed battery.
 Do not solder the battery directly.
 Remove the battery whose life cycle has
expired from equipment immediately.
 Remember to recycle: The cardboard packing
supplied with this device is ideal for recycling.
Warnings: In the unlikely event of a battery leak,
take care to keep the leakage away from your eyes
and skin. If the leakage does come into contact
with the eyes or skin, flush thoroughly with clean
water and consult with a doctor.
Aircraft Safety
Switch off your device before the airplane takes
off. In order to protect airplane’s communication
system from interference, it is never allowed
to use the device when in flight. Get aircrew’s
permission if you want to use the device prior to
take-off.
46
Hospital Safety


Switch off your device and remove its battery
in areas where device use is prohibited.
Follow the instructions given by any respective
medical facility regarding the use of Wireless
devices on their premises.
Road Safety






You must exercise proper control of your
vehicle at all times. Give your full attention to
driving.
Observe all of the recommendations contained
in your local traffic safety documentation.
Please check if local laws and/or regulations
restrict the use of wireless devices while
driving.
Switch off your device at a refueling point,
such as a gas station, even if you are not
refueling your own car.
Do not store or carry flammable or explosive
materials in the same compartment as the
device.
Electronic systems in a vehicle, such as antilock brakes, speed control and fuel injection
systems are not normally affected by radio
transmissions. The manufacturer of such
47
equipment may advise if it is adequately
shielded from radio transmissions. If you
suspect vehicle problems caused by the
radio transmitter in the device, consult your
dealer and do not switch on the device until
your device has been checked by a qualified
technician.
Vehicles Equipped with an Airbag
An airbag inflates with great force. Do not place
objects, including either installed or portable
wireless equipment, in the area over the airbag
or in the airbag deployment area. If in-vehicle
wireless equipment is improperly installed and the
airbag inflates, serious injury could result.
Third Party Equipment
The use of third party equipment, cables or
accessories, not made or authorized by ZTE,
may invalidate the warranty of the device and
also adversely affect the device’s operation. For
example, use only the ZTE charger supplied with
the device.
48
Efficient Use
For optimum performance with minimum power
consumption, do not cover the device with
anything. Covering the device may cause the
device to operate at higher power levels than
needed, and may shorten the using time of the
battery.
CTIA Requirements
a. Do not disassemble or open crush, bend or
deform, puncture or shred.
b. Do not modify or remanufacture, attempt
to insert foreign objects into the battery,
immerse or expose to water or other liquids,
expose to fire, explosion or other hazard.
c. Only use the battery for the system for which
it is specified.
d. Only use the battery with a charging system
that has been qualified with the system per
this standard. Use of an unqualified battery or
charger may present a risk of fire, explosion,
leakage, or other hazard.
e. Do not short circuit a battery or allow metallic
conductive objects to contact battery
terminals.
49
f. Replace the battery only with another battery
that has been qualified with the system per
this standard, IEEE-Std-1725-2006. Use of an
unqualified battery may present a risk of fire,
explosion, leakage or other hazard.
g. Promptly dispose of used batteries in
accordance with local regulations
h. B a t t e r y u s a g e b y c h i l d r e n s h o u l d b e
supervised.
i. Avoid dropping the phone or battery. If the
device or battery is dropped, especially on a
hard surface, and the user suspects damage,
take it to a service center for inspection.
j. Improper battery use may result in a fire,
explosion or other hazard.
For those host devices that utilize a USB port as
a charging source, the host device's user manual
shall include a statement that the device shall only
be connected to CTIA certified adapters, products
that bear the USB-IF logo or products that have
completed the USB-IF compliance program.
Radio Frequency (RF) Exposure
This device meets the government’s requirements
for exposure to radio waves.
50
This device is designed and manufactured not
to exceed the emission limits for exposure to
radio frequency (RF) energy set by the Federal
Communications Commission of the U.S.
Government:
The exposure standard for wireless mobile
devices employs a unit of measurement known as
the Specific Absorption Rate, or SAR. The SAR
limit set by the FCC is 1.6W/kg. *Tests for SAR
are conducted using standard operating positions
accepted by the FCC with the device transmitting
at its highest certified power level in all tested
frequency bands. Although the SAR is determined
at the highest certified power level, the actual
SAR level of the device while operating can be
well below the maximum value. This is because the
device is designed to operate at multiple power
levels so as to use only the poser required to reach
the network. In general, the closer you are to a
wireless base station antenna, the lower the power
output.
T h e h i g h e s t SA R v a l u e f o r t h e d ev i c e a s
reported to the FCC is 1.39 W/kg (Body-worn
measurements differ among device models,
depending upon available enhancements and FCC
requirements.)
51
While there may be differences between the SAR
levels of various devices and at various positions,
they all meet the government requirement.
The FCC has granted an Equipment Authorization
for this device with all reported SAR levels
evaluated as in compliance with the FCC RF
exposure guidelines. SAR information on this
device is on file with the FCC and can be found
under the Display Grant section of http://www.fcc.
gov/oet/ea/fccid/ after searching on:
FCC ID: Q78-EUFI890
For body worn operation, this device has been
tested and meets the FCC RF exposure guidelines
for use with an accessory that contains no metal
and the positions the handset a minimum of 1.5
cm from the body. Use of other enhancements
may not ensure compliance with FCC RF exposure
guidelines. If you do no t use a body-worn
accessory and are not holding the device at the
ear, position the handset a minimum of 1.5 cm
from your body when the device is switched on.
FCC Compliance
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
52
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
Caution: Changes or modifications not expressly
approved by the manufacturer could void the user’
s authority to operate the equipment.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the
equipment and receiver.
53
— Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV
technician for help.
54
Consumer Limited Warranty
ZTE (“Seller”) offers you a limited warranty
that the enclosed product or products (the
“Product”) will be free from defects in material
and workmanship for a period that expires one
year from the date of sale of the Product to
you, provided that you are the original end-user
purchaser of the Product and provided that your
purchase was made from a supplier authorized
by the Seller. Transfer or resale of a Product will
automatically terminate warranty coverage with
respect to that Product. This limited warranty is
not transferable to any third party, including but
not limited to any subsequent purchaser or owner
of the Product. This limited warranty is applicable
only to end users in the United States.
Seller will, at its sole and absolute discretion,
either repair or replace a Product (for which Seller
may use refurbished parts of similar quality and
functionality) if found by Seller to be defective in
material or workmanship, or if Seller determines
that it is unable to repair or replace such Product,
Seller will refund the purchase price for such
Product, provided that the subject Product (i) is
returned to a Seller authorized service center
55
within the one year warranty period, and (ii) is
accompanied by a proof of purchase in the form of
a bill of sale or receipted invoice which evidences
that the subject Product is within the one year
warranty period. After the one year warranty
period, you must pay all shipping, parts and labor
charges. In the event that the Product is deemed
un-repairable or has been removed from the list of
products supported by the Seller, you will only be
liable for shipping and labor charges.
This limited warranty does not cover and is void
with respect to the following: (i) any Product
which has been improperly installed, repaired,
maintained or modified; (ii) any Product which
has been subjected to misuse (including any
Product used in conjunction with hardware
electrically or mechanically incompatible or used
with accessories not approved by Seller), abuse,
accident, physical damage, abnormal operation,
improper handling, neglect, exposure to fire or
liquid; (iii) any Product operated outside published
maximum ratings; (iv) cosmetic damage; (v) any
Product on which warranty stickers or Product
serial numbers have been removed, altered,
or rendered illegible; (vi) cost of installation,
removal or reinstallation; (vii) signal reception
56
problems (unless caused by defects in material
and workmanship); (viii) damage as a result of
fire, flood, acts of God or other acts which are not
the fault of Seller and which the Product is not
specified to tolerate, including damage caused
by mishandling, shipping and blown fuses; (ix)
consumables (such as fuses); or (x) any Product
which has been opened, repaired, modified or
altered by anyone other than Seller or a Seller
authorized service center.
USE ONLY SELLER APPROVED ACCESSORIES
WITH SELLER DEVICES. USE OF ANY
U N A U T H O R I Z E D A C C E S S O R I E S M AY B E
DANGEROUS AND WILL INVALIDATE THE DEVICE
WARRANTY IF SAID ACCESSORIES CAUSE
DAMAGE OR A DEFECT TO THE DEVICE.
SELLER SPECIFICALLY DISCLAIMS LIABILITY
FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL,
GENERAL, PUNITIVE, EXEMPLARY, AGGRAVATED,
INCIDENTAL OR CONSEQUENTIAL DAMAGES,
EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES, WHETHER FORESEEABLE OR
UNFORESEEABLE OF ANY KIND WHATSOEVER,
INCLUDING BUT NOT LIMITED TO LOSS OF
P R O F I T S , U N A N T I C I PAT E D B E N E F I T S O R
REVENUE, ANTICIPATED PROFITS ARISING OUT
57
OF USE OF OR INABILITY TO USE ANY PRODUCT
(FOR EXAMPLE, WASTED AIRTIME CHARGES
DUE TO THE MALFUNCTION OF A PRODUCT) OR
CONTRIBUTION OR INDEMNITY IN RESPECT OF
ANY CLAIM RELATED TO A PRODUCT.
REPAIR OR REPLACEMENT OF A DEFECTIVE
PRODUCT OR REFUND OF THE PURCHASE
PRICE RELATING TO A DEFECTIVE PRODUCT,
AS PROVIDED UNDER THIS WARRANTY, ARE
YOUR SOLE AND EXCLUSIVE REMEDIES FOR
BREACH OF THE LIMITED WARRANTY, AND
SUBJECT TO THIS WARRANTY, THE PRODUCTS
ARE APPROVED AND ACCEPTED BY YOU “AS
IS”. SELLER MAKES NO OTHER WARRANTIES,
R E P R E S E N TAT I O N S O R C O N D I T I O N S O F
ANY KIND, ORAL OR VERBAL, EXPRESS OR
IMPLIED, STATUTORY OR OTHERWISE, WITH
RESPECT TO THE PRODUCTS, INCLUDING BUT
NOT LIMITED TO ANY IMPLIED WARRANTY OR
CONDITION OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE OR AGAINST
INFRINGEMENT OR ANY IMPLIED WARRANTY
OR CONDITION ARISING OUT OF TRADE USAGE
OR OUT OF A COURSE OF DEALING OR COURSE
OF PERFORMANCE. NO DEALER, DISTRIBUTOR,
AGENT OR EMPLOYEE IS AUTHORIZED TO MAKE
58
ANY MODIFICATION OR ADDITION TO THIS
WARRANTY.
Some jurisdictions do not allow the exclusion
or limitation of incidental or consequential
damages, or allow limitations on how long an
implied warranty lasts, so the above limitations
or exclusions may not apply to you. This limited
warranty gives you specific legal rights, and
you may also have other rights which vary from
jurisdiction to jurisdiction.
For warranty service information, please call the
following telephone number: 1-877-817-1759,
1-212-444-0502 or return to the point of sale for
the products.
59
Verizon Jetpack™
4G LTE Mobile Hotspot - 890L
USER
GUIDE
USER GUIDE
105 mm
XXXX0000000(0.0) X
75 mm
Verizon Jetpack™
4G LTE Mobile Hotspot
Model#: 890L
Global Ready™
10 mm
Job Number
Project
100035015 In Box Collateral
Client
Inks
Verizon
Rev No.
File Name
UG_EuFi890_CVR_75x105_NHS_V0_R2.ai
0
Description
Date
11/02/11
Produced By
75 x 105 User Guide
Mary Salazar
THIS FILE MAY CONTAIN IMAGES OR ILLUSTRATIONS THAT ARE COPYRIGHT PROTECTED. CLIENT MUST OBTAIN PROPER LICENSING AND USAGE RIGHTS PRIOR TO REPRODUCTION.
SUPPLIER IS RESPONSIBLE FOR CHECKING WORKING DRAWINGS BEFORE PLATES ARE MADE FOR ACCURACY IN MEASUREMENTS, PLATE TOLERANCE REQUIREMENTS,
REGISTRATION AND CONSTRUCTION DETAILING. ANY CHANGES MADE TO SUIT PRODUCTION REQUIREMENTS SHOULD BE APPROVED BY BOTH THE CLIENT AND DESIGN DIRECTOR.
ALL COPY SHOULD BE PROOFREAD BY CLIENT AND LEGAL REQUIREMENTS CHECKED BY CLIENT’S LEGAL DEPARTMENT.
Designer
Production
Proofreader
PROCESS
CYAN
PROCESS
MAGENTA
PROCESS
YELLOW
PROCESS
BLACK
Finishes
Client Services
NOTES: VARNISH LAYER HAS BEEN PROVIDED IN THIS FILE.
PROCESS COLOR VALUES ARE BASED ON ARTWORK PROVIDED AND HAVE NOT
BEEN ALTERED.
MATTE
VARNISH
This Proof Indicates Approximate Color Only. For Accurate Color Match, Use Approved Color Standard.
DO NOT USE COLOR FORMULAS ON THIS FILE.