PA246 Series
LCD Monitor
User Guide
Downloaded from ManualMonitor.com Manuals
Contents
Contents........................................................................................................ ii
Notices.......................................................................................................... iii
Safety information....................................................................................... iv
Care & Cleaning............................................................................................ v
Chapter 1:
Product introduction
1.1
Welcome! ..................................................................................... 1-1
1.2
Package contents.......................................................................... 1-1
1.3
Monitor introduction..................................................................... 1-2
1.3.1
Front view........................................................................ 1-2
1.3.2
Back view......................................................................... 1-3
1.3.3
QuickFit Function............................................................. 1-4
Chapter 2:
Setup
2.1
Detaching the arm/base
(for VESA wall mount).................................................................. 2-1
2.2
Adjusting the monitor................................................................... 2-2
2.3
Connecting the cables.................................................................. 2-3
2.4
Turning on the monitor................................................................. 2-3
Chapter 3:
3.1
General instructions
OSD (On-Screen Display) menu ................................................. 3-1
3.1.1
How to reconfigure........................................................... 3-1
3.1.2
OSD function introduction................................................ 3-1
3.2
Specifications summary (PA246)................................................ 3-7
3.3
Troubleshooting (FAQ)................................................................. 3-8
3.4
Supported operating modes........................................................ 3-9
iiDownloaded
from ManualMonitor.com Manuals
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
This device may not cause harmful interference, and
•
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with manufacturer’s
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modifications
to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
This Class B digital apparatus meets all requirements of the Canadian Interference
- Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Réglement sur le matériel brouiller du Canada.
Downloaded from ManualMonitor.com Manuals
iii
Safety information
•
Before setting up the monitor, carefully read all the documentation that came
with the package. •
To prevent fire or shock hazard, never expose the monitor to rain or moisture. •
Never try to open the monitor cabinet. The dangerous high voltages inside the
monitor may result in serious physical injury.
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified
service technician or your retailer. •
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
•
Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiator or heat source unless proper ventilation is provided.
•
The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
•
Use the appropriate power plug which complies with your local power
standard.
•
Do not overload power strips and extention cords. Overloading can result in
fire or electric shock. •
Avoid dust, humidity, and temperature extremes. Do not place the monitor in
any area where it may become wet. Place the monitor on a stable surface.
•
Unplug the unit during a lightning storm or if it will not be used for a long period
of time. This will protect the monitor from damage due to power surges.
•
Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
•
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between
100-240V AC. •
If you encounter technical problems with the monitor, contact a qualified
service technician or your retailer. This symbol of the crossed out wheeled bin indicates that the product (electrical,
electronic equipment, and mercury-containing button cell battery) should not
be placed in municipal waste. Please check local regulations for disposal of
electronic products.
ivDownloaded
from ManualMonitor.com Manuals
Care & Cleaning
•
Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
•
Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
•
Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the monitor. Never spray cleaner directly on the screen, as it may
drip inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
•
The screen may flicker during the initial use due to the nature of the fluorescent
light. Turn off the Power Switch and turn it on again to make sure that the
flicker disappears. •
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
•
When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
•
When the screen becomes black or flashes, or cannot work anymore, contact
your dealer or service center to fix it. Do not repair the screen by yourself! Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when
trying to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
Downloaded from ManualMonitor.com Manuals
v
Where to find more information
Refer to the following sources for additional information and for product and
software updates.
1.
ASUS websites
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. Refer to http://www.asus.com
2.
Optional documentation
Your product package may include optional documentation that may have
been added by your dealer. These documents are not part of the standard
package.
viDownloaded
from ManualMonitor.com Manuals
1.1
Welcome!
Thank you for purchasing the ASUS® LCD monitor!
The latest widescreen LCD monitor from ASUS provides a crisper, broader, and
brighter display, plus a host of features that enhance your viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the monitor brings to you!
1.2
Package contents
Check your package for the following items:
LCD monitor
Quick start guide
Warranty card
Power cord
VGA cable
DVI cable
DisplayPort cable
USB cable
Support CD
Cable tie
Color Calibration Testing Report
If any of the above items is damaged or missing, contact your retailer
immediately.
ASUS PA246
Series
LCD Monitor
Downloaded
from
ManualMonitor.com
Manuals
1-1
1.3
Monitor introduction
1.3.1
Front view
1
1.
2
3
4
5
6
7
QuickFit button:
•
Activates the QuickFit function designed for alignment.
•
The QuickFit function contains 7 pages of common grid patterns and paper
and photo sizes. (Please refer to 1.3.3 QuickFit Function).
•
Selects a desired preset mode.
•
Exits the OSD menu or goes back to the previous menu when the OSD
menu is active.
•
Automatically adjusts the image to its optimized position, clock, and phase
by pressing this button for 2-4 seconds (for VGA mode only).
•
Decreases values or moves your selection left/down.
•
Contrast hotkey
2.
button:
3.
4.
MENU button:
•
Turns on the OSD menu. Enacts the selected OSD menu item.
•
Exits the hotkey OSD menu.
1-2
Downloaded
from ManualMonitor.com Manuals
Chapter 1: Product introduction
5.
•
Increases values or moves your selection right/up.
•
Brightness hotkey
•
Selects an available input source.
6.
button:
button (Input Select button) to display HDMI/DisplayPort
signals after you connect HDMI/DisplayPort cable with the monitor.
Press
7.
Power button/power indicator
•
Turns the monitor on/off.
•
The color definition of the power indicator is as the below table.
1.3.2
Status
Description
White
Orange
OFF
ON
Standby mode
OFF
Back view
2
1
3
4
5
6
7 8
9
10
11
Rear connectors
1.
Power switch. Press the switch to turn on/off power.
2.
AC-IN port. This port connects the power cord.
3.
DisplayPort. This port is for connection for a DisplayPort compatible device.
4.
HDMI port. This port is for connection with an HDMI compatible device.
ASUS PA246
Series
LCD Monitor
Downloaded
from
ManualMonitor.com
Manuals
1-3
5.
DVI port. This 24-pin port is for PC (Personal Computer) DVI-D digital signal
connection.
6.
VGA port. This 15-pin port is for PC VGA connection.
7.
Earphone jack.
8.
USB upstream port. This port is for connection with a USB upstream cable.
The cable enables the USB ports and card reader on the monitor.
9.
Kensington lock slot.
10. Card reader. See below for more information about the card reader
specifications.
11. USB downstream ports. These ports are for connection with USB devices,
such as USB keyboard/mouse, USB flash drive, etc.
Card reader specifications
Memory Stick (MS),
High Speed Memory Stick (HSMS),
Memory Stick PRO (MSPRO),
Memory Stick Duo(w Adapter),
MS Duo Secure Digital (Mini-SD), Secure Digital Card,
Supported
Mini Secure Digital(w Adaptor),
Media Types :
TransFlash(SD, including SDHC),
MultiMediaCard(MMC), Reduced Size MultiMediaCard(RSMMC),
NAND Flash,
xD
Lower Slot (built-in Push Ejection Mechanism):
SD / MS / MMC/xD – direct insertion
Card Slots :
MS Duo / Mini-SD / TransFlash Card / RS-MMC – with
adapter
1.3.3
QuickFit Function
The QuickFit function contains three kinds of patterns: (1) Grid patterns (2) Paper
size (3) Photo size.
1. Grid patterns
The grid patterns facilitate designers and users to organize content and layout on a
page and achieve a consistent look and feel.
Centimeters
1-4
Downloaded
Inches
from ManualMonitor.com Manuals
Chapter 1: Product introduction
Alignment Grid
2. Paper size
QuickFit provides numerous commonly used standard paper sizes for users to view
their documents in real size on the screen.
A4
Letter
3. Photo size
The various real photo sizes displayed in the QuickFit function provides
photographers and other users to accurately view and edit their photos in real size
on the screen.
Photo 4x6, 3x5, 2x2
Photo 8x10, 5x7
ASUS PA246
Series
LCD Monitor
Downloaded
from
ManualMonitor.com
Manuals
1-5
1-6
Downloaded
from ManualMonitor.com Manuals
Chapter 1: Product introduction
2.1
Detaching the arm/base
(for VESA wall mount)
The detachable arm/base of this monitor is specially designed for VESA wall mount.
To detach the arm/base:
1.
Have the front of the monitor face down on a table.
2.
Use a screwdriver to remove the four screws on the arm (Figure 1), and then
detach the arm/base from the monitor (Figure 2).
(Figure 1)
(Figure 2)
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
ASUS PA246
Series
LCD Monitor
Downloaded
from
ManualMonitor.com
Manuals
2-1
2.2
Adjusting the monitor
•
or optimal viewing, we recommend that you look at the full face of the
F
monitor, then adjust the monitor to the angle that is most comfortable for you.
•
Hold the stand to prevent the monitor from falling when you change its angle.
•
ou can adjust the monitor’s angle from +20˚ to -5˚ and it allows 60˚ swivel
Y
adjustment from either left or right. You can also adjust the monitor’s height
within +/- 10 cm.
(Tilt)
(Swivel)
(Height adjustment)
+20° ~ -5°
10cm
60°
0°
60°
Pivoting the monitor
1. Lift the monitor to the highest position.
2. Tilt the monitor to its maximum angle.
3. Pivot the monitor clockwise to the angle you need.
+20° ~ -5°
It is normal that the monitor slightly shakes while you adjust the viewing angle.
2-2
Downloaded
from ManualMonitor.com Manuals
Chapter 2: Setup
2.3
1.
Connecting the cables
Connect the cables as the following instructions:
•
To connect the power cord: connect one end of the power cord securely to
the monitor’s AC input port, the other end to a power outlet.
•
To connect the VGA/HDMI/DVI/DisplayPort cable:
a. Plug one end of the VGA/HDMI/DVI/DisplayPort cable to the monitor’s
VGA/HDMI/DVI/DisplayPort jack.
b. Connect the other end of the VGA/HDMI/DVI/DisplayPort cable to your
computer's VGA/HDMI/DVI/DisplayPort jack.
c.
Tighten the two screws to secure the VGA/DVI connector.
•
To use the earphone: connect the end with plug type to the monitor’s
earphone jack when an HDMI or DisplayPort signal is fed.
•
To use the USB ports: Plug the smaller end (type B) of the USB upstream
cable to the monitor’s USB upstream port, and the larger end (type A) to your
computer’s USB port. That will enable the USB ports and card reader on the
monitor to work.
When these cables are connected, you can choose the desired signal from the
Input Select item in the OSD menu.
2.4
Turning on the monitor
Press the power button . See page 1-2 for the location of the power button. The
power indicator lights up in white to show that the monitor is ON.
ASUS PA246
Series
LCD Monitor
Downloaded
from
ManualMonitor.com
Manuals
2-3
2-4
Downloaded
from ManualMonitor.com Manuals
Chapter 2: Setup
3.1
OSD (On-Screen Display) menu
3.1.1
How to reconfigure
1.
Press the MENU button to activate the OSD menu.
2.
Press
, and
to navigate through the functions. Highlight the
desired function and press the MENU button to activate it. If the function
selected has a sub-menu, press
and
again to navigate
through the sub-menu functions. Highlight the desired sub-menu function and
press the MENU button to activate it.
3.
Press
4.
To exit and save the OSD menu, press the
button repeatedly until the
OSD menu disappears. To adjust other functions, repeat steps 1-3.
3.1.2
1.
, and
to change the settings of the selected function.
OSD function introduction
Splendid
This function contains six sub-functions you can select for your preference.
Each mode has the Reset selection, allowing you to maintain your setting or
return to the preset mode.
•
Standard Mode: best choice for document editing with SPLENDID™
Video Enhancement.
•
sRGB Mode: compatible with sRGB color space, sRGB mode is the best
choice for document editing.
ASUS PA246
Series
LCD Monitor
Downloaded
from
ManualMonitor.com
Manuals
3-1
Color
Space
sRGB
•
•
•
Xr
0.64
Yr
0.33
Primaries
Xg
Yg
0.3
0.6
Xb
Yb
0.15 0.06
Adobe RGB Mode: compatible with Adobe RGB color space.
Color
Space
Adobe
RGB
•
White Point
Xw
Yw
0.3127 0.329
White Point
Xw
Yw
Xr
Yr
0.3127 0.329
0.64
0.33
Primaries
Xg
Yg
0.21
0.71
Xb
Yb
0.15
0.06
Scenery Mode: best choice for scenery photo display with SPLENDID™
Video Enhancement.
Theater Mode: best choice for movies with SPLENDID™ Video
Enhancement.
User Mode: More items are adjustable in the Color menu.
3-2
Chapter 3: OSD (On-Screen Display) menu
Downloaded
from ManualMonitor.com Manuals
Function
Brightness
Contrast
Saturation
Hue
Color Temperature
Gamma
Six-axis
Hue
Advanced Six-axis
Saturation
Setting
Gain
Offset
2.
Adobe
Standard sRGB
Scenery Theater User
RGB
Mode
Mode
Mode Mode Mode
Mode
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
No
No
No
Yes
Yes
Yes
No
No
No
No
No
Yes
Yes
No
No
Yes
Yes
No
Yes
No
No
No
No
Yes
No
No
No
No
No
Yes
No
No
No
No
No
Yes
No
No
No
No
No
Yes
No
No
No
No
No
Yes
Color
Set a desired color setting from this menu.
•
Brightness: the adjusting range is from 0 to 100.
activate this function.
•
Contrast: the adjusting range is from 0 to 100.
activate this function.
•
Saturation: the adjusting range is from 0 to 100.
•
Hue: shifts the image color between green and purple.
•
Color Temp.: contains 3 modes including 9300K, 6500K and 5000K.
•
Gamma: allows you to set the color mode to 2.2 or 1.8 (D50).
•
Advanced Setting:
*
is a hotkey to
is a hotkey to
6-axis Hue adjustment.
ASUS PA246
Series
LCD Monitor
Downloaded
from
ManualMonitor.com
Manuals
3-3
•
3.
*
6-axis Saturation adjustment.
*
Adjusts the gain levels for R, G, B.
* Adjusts the black level offset values for R, G, B.
Color Reset:
*
Current Splendid color mode reset:
Resets the color settings of current color mode to the factory
default value.
*
All Splendid color mode reset:
Resets the color settings of all color modes to the factory default
value.
Image
Set the image related setting from this menu.
•
Sharpness: the adjusting range is from 0 to 100.
•
Aspect Control: adjusts the aspect ratio to full, 4:3, 1:1, or OverScan
(only available for the HDMI input).
•
ASCR: turns on/off the ASCR (ASUS Smart Contrast Ratio) function.
3-4
Chapter 3: OSD (On-Screen Display) menu
Downloaded
from ManualMonitor.com Manuals
•
•
•
4.
Position: adjusts the horizontal position (H-Position) and the vertical
position (V-Position) of the image. The adjusting range is from 0 to 100.
Focus: reduces Horizonal-line noise and Vertical-line noise of the image
by adjusting (Phase) and (Clock) separately. The adjusting range is from
0 to 100.
AUTO Adjust.: Automatically adjusts the image to its optimized position,
clock, and phase.
•
Phase adjusts the phase of the pixel clock signal. With a wrong phase
adjustment, the screen shows horizontal disturbances.
•
Clock (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the image is not proportional.
PIP Setting
The PIP Setting allows you to open up another sub-window connected from
another video source besides the main-window from your original video
source. By activating this function, you can have two pictures from two
different video sources displayed by the monitor.
•
PIP Mode: turns the PIP function on or off.
•
PIP Source: Selects the video input source from among VGA, DVI,
HDMI, and DisplayPort.
•
Size: Adjusts the PIP size to Small, Middle, or Large.
•
Position: Adjusts the position of the sub-window to Right-Top, Left-Top,
Right-Bottom, or Left-Bottom.
•
Switch: Switches the sources of the main and sub-windows.
The DVI and HDMI input sources should not be selected as the mainwindow or sub-window at the same time. See the table below for details.
VGA
Sub-window
VGA
DVI
HDMI
DisplayPort
Yes
Yes
Yes
ASUS PA246
Series
LCD Monitor
Downloaded
from
ManualMonitor.com
Manuals
Main-window
DVI
Yes
No
Yes
HDMI
Yes
No
DisplayPort
Yes
Yes
Yes
Yes
3-5
5.
Input Select
In this function, you can select your desired input source.
6.
System Setup
Allows you to adjust the system.
•
Splendid Demo Mode: splits the screen into two for Splendid modes
comparison. (Scenery mode/theater mode only)
•
OSD Setup:
*
Adjusts the horizontal position (H-Position)/the vertical position
(V-Position) of the OSD from 0 to 100.
*
Adjusts the OSD timeout from 10 to 120 seconds.
*
Enables or disables the DDC/CI function.
*
Adjusts the OSD background from opaque to transparent.
•
Information: shows the monitor information.
•
•
Language: there are 10 languages for your selection, including English,
French, German, Spanish, Italian, Dutch, Russian, Traditional Chinese,
Simplified Chinese, and Japanese.
Power Indicator: turns the power LED indicator on/off.
•
All Reset: “Yes” allows you to restore the default settings.
3-6
Chapter 3: OSD (On-Screen Display) menu
Downloaded
from ManualMonitor.com Manuals
3.2
Specifications summary (PA246)
Panel Type
Panel size
Max. Resolution
Pixel pitch
Brightness (Max.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
Response time
SPLENDID™ Video
Enhancement
SPLENDID™ selection
Auto adjustment
Color temperature selection
Digital input
Analog input
Earphone jack
Colors
Power LED
Tilt
Swivel
Height Adjustment
Kensington lock
AC input voltage
Power consumption
Temperature (Operating)
Temperature
(Non-operating)
Dimension (W x H x D)
Weight (Esti.)
Multi-languages
Accessories
Regulation approvals
TFT LCD
24.1" (16:10, 61.13 cm) wide screen
1920 x 1200
0.270 mm
400 cd/m2
1000:1
50,000:1 (with ASCR on)
178˚/178˚
1.07 Billion
6 ms (Gray to gray)
Yes
6 video preset modes (by hotkey)
Yes
3 color temperatures
HDMI v1.3, DisplayPort V1.1a, DVI-D with HDCP
D-Sub
Yes
Black
White (On)/Orange (Standby)
+20˚~ -5˚
+60˚~ -60˚
100 mm
Yes
AC: 100~240V
Power On: < 130 W (Max.), Standby: < 1 W (Typ.),
Power Off: 0 W (Switch off)
0˚C~40˚C
-20˚C~+60˚C
559 mm x 381 mm x 235 mm (machine)
683 mm x 457 mm x 298 mm (package)
7.3 kg (Net); 10.7 kg (Gross)
10 languages (English, German, Italian, French, Dutch,
Spanish, Russian, Traditional Chinese, Simplified
Chinese, Japanese)
VGA cable, DVI cable, DisplayPort cable, Power cord,
USB cable, Quick start guide, Warranty card, Support
CD, Cable tie, Color Calibration Testing Report
TCO03, TUV-GS, TUV-Ergo, ErP, UL/cUL, CB, CE,
FCC, CCC, BSMI, Gost-R, C-Tick, VCCI, PSB, J-MOSS,
RoHS, WEEE, Windows 7 WHQL
*Specifications are subject to change without notice.
ASUS PA246
Series
LCD Monitor
Downloaded
from
ManualMonitor.com
Manuals
3-7
3.3
Troubleshooting (FAQ)
Problem
Power LED is not ON
The power LED lights amber and there is
no screen image
Screen image is too light or dark
Possible Solution
• Press the button to check if the monitor
is in the ON mode.
• Check if the power cord is properly
connected to the monitor and the power
outlet.
• Check if the power switch is ON.
• Check if the monitor and the computer are
in the ON mode.
• Make sure the signal cable is properly
connected the monitor and the computer.
• Inspect the signal cable and make sure
none of the pins are bent.
• Connect the computer with another
available monitor to check if the computer
is properly working.
• Adjust the Contrast and Brightness
settings via OSD.
Screen image is not centered or sized
properly
• Press the
button for 2-4 seconds
to automatically adjust the image (for VGA
mode only).
• Adjust the H-Position or V-Position
settings via OSD.
Screen image bounces or a wave pattern is • Make sure the signal cable is properly
present in the image
connected to the monitor and the
computer.
• Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does • Inspect the signal cable and make sure
not look white)
that none of the pins are bent.
• Perform All Reset via OSD.
• Adjust the R/G/B color settings or select
the Color Temperature via OSD.
Screen image is blurry or fuzzy
• Press the
button for 2-4 seconds
to automatically adjust the image (for VGA
mode only).
• Adjust the Phase and Clock settings via
OSD.
No sound or sound is low
• Ensure that the HDMI cable is properly
connected to the monitor and the
computer.
• Adjust the volume settings of both your
monitor and HDMI device.
• Ensure that the computer sound card
driver is properly installed and activated.
3-8
Chapter 3: OSD (On-Screen Display) menu
Downloaded
from ManualMonitor.com Manuals
3.4
Supported operating modes
Resolution
Frequency
Horizontal
Frequency (KHz)
Vertical Frequency
(Hz)
Pixel
(MHz)
640x480
640x480
640x480
640x480
720x400
800x600
800x600
800x600
800x600
832X624
1024x768
1024x768
1024x768
1152x864
1280x960
1280x1024
1280x1024
1366x768
1440x900
1600x1200
1680x1050
31.47(N)
35.00(N)
37.87(N)
37.5(N)
31.47(N)
35.16(P)
37.88(P)
48.08(P)
46.86(P)
49.72(P/N)
48.36(N)
56.476(N)
60.02(N)
67.5(P/N)
60.00(P)
63.98(P)
79.98(P)
47.712(P)
55.94(N)
75.00(P)
65.29(N)
59.94(N)
66.66(N)
72.82(N)
75.00(N)
70.08(P)
56.25(P)
60.32(P)
72.12(P)
75.00(P)
74.55(P/N)
60.00(N)
70.069(N)
75.00(N)
75.00(P/N)
60.00(N)
60.02(P)
75.02(P)
59.79(P)
59.89(P)
60.00(P)
60.00(P)
25.18
30.24
31.5
31.5
28.32
36
1920x1080
67.5(P)
60.00(P)
148.5
1920x1200
(Reduced Blanking)
74.038(P)
59.95(N)
154
1920x1200
74.556(N)
59.885(P)
193.25
40
50
49.5
57.28
65
75
78.75
108
108
108
135
85.5
106.5
162
146.25
* Modes not listed in the table may not be supported. For optimal resolution, we recommend that
you choose a mode listed in the table above.
* This monitor supports full HD (480p, 576p, 720p, 1080i/p) video content from game consoles, DVD
players and other consumer video devices via HDMI or DisplayPort.
ASUS PA246
Series
LCD Monitor
Downloaded
from
ManualMonitor.com
Manuals
3-9