SEKURE Paradox Digiplex DGP-610 Installation manual

96-Zone Expandable Security and Access Control Panel
(DGP-NE96)
Programming Guide V1.5
DGP-NE96
Default Installer Code
000000 (To modify the installer code, refer to section [1000], Installer Code Programming on page 22)
Default System Master Code
1234
or
123456
How Do I Enter Programming Mode?
1)
2)
3)
4)
Press and hold the [0] key.
Enter your [INSTALLER CODE].
Enter 4-digit [SECTION].
Enter required [DATA].
Decimal and Hexadecimal Programming Table
Certain sections may require the entry of one or more Hexadecimal values from 0 to F.
For LCD keypads:
Key
[0] to [9]
Value or Action
0 to 9 (Hex & Decimal)
Key
[BYP]
Value or Action
E (Hex Only)
[STAY]
A (Hex Only)
[MEM]
[FORCE]
B (Hex Only)
[CLEAR]
Exit section without saving (Hex & Decimal)
F (Hex Only)
[ARM]
C (Hex Only)
[ENTER]
Save current data and advance to next section (Hex Only)
[DISARM]
D (Hex Only)
For Grafica keypads:
[0] to [9]
[#]
= values 0 to 9 respectively
= A to F (press the [#] key until the
desired letter appears)
Right Action Key (Exit)
Center Action Key (Save)
www.paradox.ca
= Exit section without saving
= Save current data and advance to next
section
Digiplex DGP-NE96
-2-
Programming Guide
Table of Contents
Serial Number List................................................................................................................................ 4
Zone Programming .............................................................................................................................. 7
Zone Report Codes ............................................................................................................................ 10
Zone Labels ........................................................................................................................................ 12
Keyswitch Programming ................................................................................................................... 13
Programmable Outputs ..................................................................................................................... 15
User Code Options............................................................................................................................. 22
Arming and Disarming Report Codes .............................................................................................. 24
Access Control Sections ................................................................................................................... 25
Keypad Numbering ............................................................................................................................ 29
Control Panel Settings....................................................................................................................... 29
System Options .................................................................................................................................. 29
Dialer Options..................................................................................................................................... 30
Other Options ..................................................................................................................................... 31
Communication Settings ................................................................................................................... 32
System Event Call Direction.............................................................................................................. 33
Partition Settings................................................................................................................................ 34
Special and Trouble Report Codes................................................................................................... 39
Other Settings and Modes................................................................................................................. 40
Control Panel Hardware Connections.............................................................................................. 46
Trouble Display .................................................................................................................................. 53
Digiplex DGP-NE96
-3-
Programming Guide
Serial Number List
Remove the extra serial number sticker from the module’s PC board and affix in the appropriate spaces provided below (maximum 127 modules).
Module Type, Serial Number & Details
Module Type, Serial Number & Details
Module Type, Serial Number & Details
1:______________________________________
16:_____________________________________
31:_____________________________________
2:______________________________________
17:_____________________________________
32:_____________________________________
3:______________________________________
18:_____________________________________
33:_____________________________________
4:______________________________________
19:_____________________________________
34:_____________________________________
5:______________________________________
20:_____________________________________
35:_____________________________________
6:______________________________________
21:_____________________________________
36:_____________________________________
7:______________________________________
22:_____________________________________
37:_____________________________________
8:______________________________________
23:_____________________________________
38:_____________________________________
9:______________________________________
24:_____________________________________
39:_____________________________________
10:_____________________________________
25:_____________________________________
40:_____________________________________
11:_____________________________________
26:_____________________________________
41:_____________________________________
12:_____________________________________
27:_____________________________________
42:_____________________________________
13:_____________________________________
28:_____________________________________
43:_____________________________________
14:_____________________________________
29:_____________________________________
44:_____________________________________
15:_____________________________________
30:_____________________________________
45:_____________________________________
Digiplex DGP-NE96
-4-
Programming Guide
Module Type, Serial Number & Details
Module Type, Serial Number & Details
Module Type, Serial Number & Details
46:_____________________________________
62:_____________________________________
78:_____________________________________
47:_____________________________________
63:_____________________________________
79:_____________________________________
48:_____________________________________
64:_____________________________________
80:_____________________________________
49:_____________________________________
65:_____________________________________
81:_____________________________________
50:______________________________________ 66:_____________________________________
82:_____________________________________
51:______________________________________ 67:_____________________________________
83:_____________________________________
52:______________________________________ 68:_____________________________________
84:_____________________________________
53:______________________________________ 69:_____________________________________
85:_____________________________________
54:______________________________________ 70:_____________________________________
86:_____________________________________
55:______________________________________ 71:_____________________________________
87:_____________________________________
56:______________________________________ 72:_____________________________________
88:_____________________________________
57:______________________________________ 73:_____________________________________
89:_____________________________________
58:______________________________________ 74:_____________________________________
90:_____________________________________
59:_____________________________________
75:_____________________________________
91:_____________________________________
60:_____________________________________
76:_____________________________________
92:_____________________________________
61:_____________________________________
77:_____________________________________
93:_____________________________________
Digiplex DGP-NE96
-5-
Programming Guide
Module Type, Serial Number & Details
Module Type, Serial Number & Details
Module Type, Serial Number & Details
94:_____________________________________
106:_____________________________________ 118:_____________________________________
95:_____________________________________
107:_____________________________________ 119:_____________________________________
96:_____________________________________
108:_____________________________________ 120:_____________________________________
97:_____________________________________
109:_____________________________________ 121:_____________________________________
98:_____________________________________
110:_____________________________________ 122:_____________________________________
99:_____________________________________
111:_____________________________________ 123:_____________________________________
100:_____________________________________ 112:_____________________________________ 124:_____________________________________
101:_____________________________________ 113:_____________________________________ 125:_____________________________________
102:_____________________________________ 114:_____________________________________ 126:_____________________________________
103:_____________________________________ 115:_____________________________________ 127:_____________________________________
104:_____________________________________ 116:_____________________________________
105:_____________________________________ 117:_____________________________________
Digiplex DGP-NE96
-6-
Programming Guide
Zone Programming
Hardwired
Device A
Keypad
SN#: 1A000252
Keypad Zone
Control Panel
SN#:020000A2
2
COMMUNICATION
CombusNETWORK
7
APR3-ZX8 Module
SN#: 34000041
Hardwired
Device B
Digiplex DGP-NE96
Detector A:
Hardwired Device A:
Hardwired Device B:
Hardwired Device C:
Zone Numbering
Sections [0001] to [0096] represent zones
1 through 96. This feature allows you to
assign an addressable or hardwired
detection device to the desired zone.
8
Input 2
1
Input Terminals
3 4 5 6
Detector A
SN#: 21000033
1
2
Input Terminals
3 4 5 6
Zone#
1=
2=
3=
4=
7
Section#
[0001]
[0002]
[0003]
[0004]
Input 5
Hardwired
Device C
Serial#
21000033
1A000252
020000A2
34000041
Input#
N/A
N/A
002
005
8
When option [1] in section [3030] is enabled for PGM1
to act as a zone input for two-wire smoke detectors,
the control panel will recognize PGM1 as input number
255.
Description
Module
Enter 3-digit [INPUT NUMBER] of the
Module to which the hardwired detection
device is connected. NOTE: No input
number is required for Addressable
Detectors, door contacts, or Keypad
Zones.
Zone Parameters
Sections [0101] to [0196] represent zones 1 through 96. This feature defines the
type of zone, its partition assignment and the zone’s options.
Enter 8-digit [SERIAL NUMBER] of the
Addressable Detector, door contact, or
Module to which the hardwired detection
device is connected.
8-digit Serial Number
Zone Options
Zone Definitions
0 - Disabled (default)
1 - Entry Delay 1
2 - Entry Delay 2
3 - Follow
4 - Instant
5 - 24Hr Buzzer
6 - 24Hr Burglary
7 - 24Hr Hold-up
8 - 24Hr Gas
9 - 24Hr Heat
A - 24Hr Water
B - 24Hr Freeze
C - Delayed 24Hr Fire
D - Standard 24Hr Fire
E - Stay Delay 1
F - Stay Delay 2
[1] Auto Zone Shutdown Enabled
[2] Bypass Enabled (default)
[3] Stay Zone
[4] Force Zone
[5]
[6]
Zone Alarm Type
off
off
Steady Alarm
off
on
Pulsed Alarm
on
off
Silent Alarm
on
on
Report Only
[7] Intellizone
[8] Delay before Transmission
Zone Partition Assignment
1 - Assigned to Partition 1 (default) 5 - Assigned to Partition 5
2 - Assigned to Partition 2
6 - Assigned to Partition 6
3 - Assigned to Partition 3
7 - Assigned to Partition 7
4 - Assigned to Partition 4
8 - Assigned to Partition 8
-7Programming Guide
Zone
1
________________________ _______________
Section
[0001]
___/___/___/___/___/___/___/___
___/___/___
Input#
Section
[0101]
2
________________________ _______________
[0002]
___/___/___/___/___/___/___/___
___/___/___
[0102]
3
________________________ _______________
[0003]
___/___/___/___/___/___/___/___
___/___/___
[0103]
4
________________________ _______________
[0004]
___/___/___/___/___/___/___/___
___/___/___
[0104]
5
________________________ _______________
[0005]
___/___/___/___/___/___/___/___
___/___/___
[0105]
6
________________________ _______________
[0006]
___/___/___/___/___/___/___/___
___/___/___
[0106]
7
________________________ _______________
[0007]
___/___/___/___/___/___/___/___
___/___/___
[0107]
8
________________________ _______________
[0008]
___/___/___/___/___/___/___/___
___/___/___
[0108]
9
________________________ _______________
[0009]
___/___/___/___/___/___/___/___
___/___/___
[0109]
10
________________________ _______________
[0010]
___/___/___/___/___/___/___/___
___/___/___
[0110]
11
________________________ _______________
[0011]
___/___/___/___/___/___/___/___
___/___/___
[0111]
12
________________________ _______________
[0012]
___/___/___/___/___/___/___/___
___/___/___
[0112]
13
________________________ _______________
[0013]
___/___/___/___/___/___/___/___
___/___/___
[0113]
14
________________________ _______________
[0014]
___/___/___/___/___/___/___/___
___/___/___
[0114]
15
________________________ _______________
[0015]
___/___/___/___/___/___/___/___
___/___/___
[0115]
16
________________________ _______________
[0016]
___/___/___/___/___/___/___/___
___/___/___
[0116]
17
________________________ _______________
[0017]
___/___/___/___/___/___/___/___
___/___/___
[0117]
18
________________________ _______________
[0018]
___/___/___/___/___/___/___/___
___/___/___
[0118]
19
________________________ _______________
[0019]
___/___/___/___/___/___/___/___
___/___/___
[0119]
20
________________________ _______________
[0020]
___/___/___/___/___/___/___/___
___/___/___
[0120]
21
________________________ _______________
[0021]
___/___/___/___/___/___/___/___
___/___/___
[0121]
22
________________________ _______________
[0022]
___/___/___/___/___/___/___/___
___/___/___
[0122]
23
________________________ _______________
[0023]
___/___/___/___/___/___/___/___
___/___/___
[0123]
Define
Assign
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
Zone Options
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
___/___/___/___/___/___/___/___
___/___/___
Section
[0124]
________________________ _______________
[0025]
___/___/___/___/___/___/___/___
___/___/___
[0125]
26
________________________ _______________
[0026]
___/___/___/___/___/___/___/___
___/___/___
[0126]
27
________________________ _______________
[0027]
___/___/___/___/___/___/___/___
___/___/___
[0127]
28
________________________ _______________
[0028]
___/___/___/___/___/___/___/___
___/___/___
[0128]
29
________________________ _______________
[0029]
___/___/___/___/___/___/___/___
___/___/___
[0129]
30
________________________ _______________
[0030]
___/___/___/___/___/___/___/___
___/___/___
[0130]
31
________________________ _______________
[0031]
___/___/___/___/___/___/___/___
___/___/___
[0131]
32
________________________ _______________
[0032]
___/___/___/___/___/___/___/___
___/___/___
[0132]
33
________________________ _______________
[0033]
___/___/___/___/___/___/___/___
___/___/___
[0133]
34
________________________ _______________
[0034]
___/___/___/___/___/___/___/___
___/___/___
[0134]
35
________________________ _______________
[0035]
___/___/___/___/___/___/___/___
___/___/___
[0135]
36
________________________ _______________
[0036]
___/___/___/___/___/___/___/___
___/___/___
[0136]
37
________________________ _______________
[0037]
___/___/___/___/___/___/___/___
___/___/___
[0137]
38
________________________ _______________
[0038]
___/___/___/___/___/___/___/___
___/___/___
[0138]
39
________________________ _______________
[0039]
___/___/___/___/___/___/___/___
___/___/___
[0139]
40
________________________ _______________
[0040]
___/___/___/___/___/___/___/___
___/___/___
[0140]
41
________________________ _______________
[0041]
___/___/___/___/___/___/___/___
___/___/___
[0141]
42
________________________ _______________
[0042]
___/___/___/___/___/___/___/___
___/___/___
[0142]
-8-
43
________________________ _______________
[0043]
___/___/___/___/___/___/___/___
___/___/___
[0143]
44
________________________ _______________
[0044]
___/___/___/___/___/___/___/___
___/___/___
[0144]
Programming Guide
45
________________________ _______________
[0045]
___/___/___/___/___/___/___/___
___/___/___
[0145]
46
________________________ _______________
[0046]
___/___/___/___/___/___/___/___
___/___/___
[0146]
47
________________________ _______________
[0047]
___/___/___/___/___/___/___/___
___/___/___
[0147]
48
________________________ _______________
[0048]
___/___/___/___/___/___/___/___
___/___/___
[0148]
49
________________________ _______________
[0049]
___/___/___/___/___/___/___/___
___/___/___
[0149]
50
________________________ _______________
[0050]
___/___/___/___/___/___/___/___
___/___/___
[0150]
51
________________________ _______________
[0051]
___/___/___/___/___/___/___/___
___/___/___
[0151]
52
________________________ _______________
[0052]
___/___/___/___/___/___/___/___
___/___/___
[0152]
53
________________________ _______________
[0053]
___/___/___/___/___/___/___/___
___/___/___
[0153]
54
________________________ _______________
[0054]
___/___/___/___/___/___/___/___
___/___/___
[0154]
55
________________________ _______________
[0055]
___/___/___/___/___/___/___/___
___/___/___
[0155]
56
________________________ _______________
[0056]
___/___/___/___/___/___/___/___
___/___/___
[0156]
57
________________________ _______________
[0057]
___/___/___/___/___/___/___/___
___/___/___
[0157]
58
________________________ _______________
[0058]
___/___/___/___/___/___/___/___
___/___/___
[0158]
59
________________________ _______________
[0059]
___/___/___/___/___/___/___/___
___/___/___
[0159]
60
________________________ _______________
[0060]
___/___/___/___/___/___/___/___
___/___/___
[0160]
61
________________________ _______________
[0061]
___/___/___/___/___/___/___/___
___/___/___
[0161]
62
________________________ _______________
[0062]
___/___/___/___/___/___/___/___
___/___/___
[0162]
63
________________________ _______________
[0063]
___/___/___/___/___/___/___/___
___/___/___
[0163]
Digiplex DGP-NE96
________________________ _______________
Section
[0024]
Zone
24
25
Description
Module
8-digit Serial Number
Input#
Define
Assign
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
Zone Options
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Zone
64
________________________ _______________
Description
Module
Section
[0064]
___/___/___/___/___/___/___/___
___/___/___
Section
[0164]
65
8-digit Serial Number
Input#
Digiplex DGP-NE96
-9Programming Guide
________________________ _______________
[0065]
___/___/___/___/___/___/___/___
___/___/___
[0165]
66
________________________ _______________
[0066]
___/___/___/___/___/___/___/___
___/___/___
[0166]
67
________________________ _______________
[0067]
___/___/___/___/___/___/___/___
___/___/___
[0167]
68
________________________ _______________
[0068]
___/___/___/___/___/___/___/___
___/___/___
[0168]
69
________________________ _______________
[0069]
___/___/___/___/___/___/___/___
___/___/___
[0169]
70
________________________ _______________
[0070]
___/___/___/___/___/___/___/___
___/___/___
[0170]
71
________________________ _______________
[0071]
___/___/___/___/___/___/___/___
___/___/___
[0171]
72
________________________ _______________
[0072]
___/___/___/___/___/___/___/___
___/___/___
[0172]
73
________________________ _______________
[0073]
___/___/___/___/___/___/___/___
___/___/___
[0173]
74
________________________ _______________
[0074]
___/___/___/___/___/___/___/___
___/___/___
[0174]
75
________________________ _______________
[0075]
___/___/___/___/___/___/___/___
___/___/___
[0175]
76
________________________ _______________
[0076]
___/___/___/___/___/___/___/___
___/___/___
[0176]
77
________________________ _______________
[0077]
___/___/___/___/___/___/___/___
___/___/___
[0177]
78
________________________ _______________
[0078]
___/___/___/___/___/___/___/___
___/___/___
[0178]
79
________________________ _______________
[0079]
___/___/___/___/___/___/___/___
___/___/___
[0179]
80
________________________ _______________
[0080]
___/___/___/___/___/___/___/___
___/___/___
[0180]
81
________________________ _______________
[0081]
___/___/___/___/___/___/___/___
___/___/___
[0181]
82
________________________ _______________
[0082]
___/___/___/___/___/___/___/___
___/___/___
[0182]
83
________________________ _______________
[0083]
___/___/___/___/___/___/___/___
___/___/___
[0183]
84
________________________ _______________
[0084]
___/___/___/___/___/___/___/___
___/___/___
[0184]
85
________________________ _______________
[0085]
___/___/___/___/___/___/___/___
___/___/___
[0185]
86
________________________ _______________
[0086]
___/___/___/___/___/___/___/___
___/___/___
[0186]
87
________________________ _______________
[0087]
___/___/___/___/___/___/___/___
___/___/___
[0187]
88
________________________ _______________
[0088]
___/___/___/___/___/___/___/___
___/___/___
[0188]
89
________________________ _______________
[0089]
___/___/___/___/___/___/___/___
___/___/___
[0189]
90
________________________ _______________
[0090]
___/___/___/___/___/___/___/___
___/___/___
[0190]
91
________________________ _______________
[0091]
___/___/___/___/___/___/___/___
___/___/___
[0191]
92
________________________ _______________
[0092]
___/___/___/___/___/___/___/___
___/___/___
[0192]
93
________________________ _______________
[0093]
___/___/___/___/___/___/___/___
___/___/___
[0193]
94
________________________ _______________
[0094]
___/___/___/___/___/___/___/___
___/___/___
[0194]
95
________________________ _______________
[0095]
___/___/___/___/___/___/___/___
___/___/___
[0195]
96
________________________ _______________
[0096]
___/___/___/___/___/___/___/___
___/___/___
[0196]
To clear a zone’s numbering (sections [0001] to [0096]):
For LCD Keypads:
1) Enter a section number between [0001] to [0096].
2) Press [0] and then [ENTER] to save and exit.
For Grafica Keypads:
1) Enter a section number between [0001] to [0096].
2) Press [0] to clear the serial number
3) Use Grafica’s scroll keys, highlight the input number and then press [0] to
clear the data.
4) Press Grafica’s center action key (Save) to save and exit.
Define
Assign
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
Zone Options
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Zone Report Codes
Ademco slow, Silent Knight fast, SESCOA, Ademco express or Pager formats:
Key-in desired 2-digit hex values from 00 to FF.
Ademco format:
Use section [4032] to program a set of default Ademco report codes from the Automatic Report Code Programming on page 41. Then to program the remaining report codes or to change some of the
defaults, enter the individual sections and key-in the desired 2-digit hex value found in the Contact ID Report Code List on page 44.
SIA format:
Use section [4032] to program a set of SIA report codes from the Automatic Report Code Programming on page 41. Codes that have not been set to default can be set to default manually by entering FF in
the appropriate section. To disable the reporting of an event, enter 00 in the appropriate section.
Zone report codes
Digiplex DGP-NE96
- 10 Programming Guide
Section
Zone #
Alarm Report
Codes
Alarm Restore
Report Codes
Tamper Report
Codes
Tamper Restore
Report Codes
Section
Zone #
Alarm Report
Codes
Alarm Restore
Report Codes
Tamper Report
Codes
Tamper Restore
Report Codes
[0201]
Zone 1
__/__
__/__
__/__
__/__
[0224]
Zone 24
__/__
__/__
__/__
__/__
[0202]
Zone 2
__/__
__/__
__/__
__/__
[0225]
Zone 25
__/__
__/__
__/__
__/__
[0203]
Zone 3
__/__
__/__
__/__
__/__
[0226]
Zone 26
__/__
__/__
__/__
__/__
[0204]
Zone 4
__/__
__/__
__/__
__/__
[0227]
Zone 27
__/__
__/__
__/__
__/__
[0205]
Zone 5
__/__
__/__
__/__
__/__
[0228]
Zone 28
__/__
__/__
__/__
__/__
[0206]
Zone 6
__/__
__/__
__/__
__/__
[0229]
Zone 29
__/__
__/__
__/__
__/__
[0207]
Zone 7
__/__
__/__
__/__
__/__
[0230]
Zone 30
__/__
__/__
__/__
__/__
[0208]
Zone 8
__/__
__/__
__/__
__/__
[0231]
Zone 31
__/__
__/__
__/__
__/__
[0209]
Zone 9
__/__
__/__
__/__
__/__
[0232]
Zone 32
__/__
__/__
__/__
__/__
[0210]
Zone 10
__/__
__/__
__/__
__/__
[0233]
Zone 33
__/__
__/__
__/__
__/__
[0211]
Zone 11
__/__
__/__
__/__
__/__
[0234]
Zone 34
__/__
__/__
__/__
__/__
[0212]
Zone 12
__/__
__/__
__/__
__/__
[0235]
Zone 35
__/__
__/__
__/__
__/__
[0213]
Zone 13
__/__
__/__
__/__
__/__
[0236]
Zone 36
__/__
__/__
__/__
__/__
[0214]
Zone 14
__/__
__/__
__/__
__/__
[0237]
Zone 37
__/__
__/__
__/__
__/__
[0215]
Zone 15
__/__
__/__
__/__
__/__
[0238]
Zone 38
__/__
__/__
__/__
__/__
[0216]
Zone 16
__/__
__/__
__/__
__/__
[0239]
Zone 39
__/__
__/__
__/__
__/__
[0217]
Zone 17
__/__
__/__
__/__
__/__
[0240]
Zone 40
__/__
__/__
__/__
__/__
[0218]
Zone 18
__/__
__/__
__/__
__/__
[0241]
Zone 41
__/__
__/__
__/__
__/__
[0219]
Zone 19
__/__
__/__
__/__
__/__
[0242]
Zone 42
__/__
__/__
__/__
__/__
[0220]
Zone 20
__/__
__/__
__/__
__/__
[0243]
Zone 43
__/__
__/__
__/__
__/__
[0221]
Zone 21
__/__
__/__
__/__
__/__
[0244]
Zone 44
__/__
__/__
__/__
__/__
[0222]
Zone 22
__/__
__/__
__/__
__/__
[0245]
Zone 45
__/__
__/__
__/__
__/__
[0223]
Zone 23
__/__
__/__
__/__
__/__
[0246]
Zone 46
__/__
__/__
__/__
__/__
Zone 47
__/__
__/__
__/__
__/__
[0272]
Zone 72
__/__
__/__
__/__
__/__
[0248]
Zone 48
__/__
__/__
__/__
__/__
[0273]
Zone 73
__/__
__/__
__/__
__/__
[0249]
Zone 49
__/__
__/__
__/__
__/__
[0274]
Zone 74
__/__
__/__
__/__
__/__
[0250]
Zone 50
__/__
__/__
__/__
__/__
[0275]
Zone 75
__/__
__/__
__/__
__/__
[0251]
Zone 51
__/__
__/__
__/__
__/__
[0276]
Zone 76
__/__
__/__
__/__
__/__
[0252]
Zone 52
__/__
__/__
__/__
__/__
[0277]
Zone 77
__/__
__/__
__/__
__/__
[0253]
Zone 53
__/__
__/__
__/__
__/__
[0278]
Zone 78
__/__
__/__
__/__
__/__
[0254]
Zone 54
__/__
__/__
__/__
__/__
[0279]
Zone 79
__/__
__/__
__/__
__/__
[0255]
Zone 55
__/__
__/__
__/__
__/__
[0280]
Zone 80
__/__
__/__
__/__
__/__
[0256]
Zone 56
__/__
__/__
__/__
__/__
[0281]
Zone 81
__/__
__/__
__/__
__/__
Digiplex DGP-NE96
[0257]
Zone 57
__/__
__/__
__/__
__/__
[0282]
Zone 82
__/__
__/__
__/__
__/__
[0258]
Zone 58
__/__
__/__
__/__
__/__
[0283]
Zone 83
__/__
__/__
__/__
__/__
[0259]
Zone 59
__/__
__/__
__/__
__/__
[0284]
Zone 84
__/__
__/__
__/__
__/__
[0260]
Zone 60
__/__
__/__
__/__
__/__
[0285]
Zone 85
__/__
__/__
__/__
__/__
[0261]
Zone 61
__/__
__/__
__/__
__/__
[0286]
Zone 86
__/__
__/__
__/__
__/__
[0262]
Zone 62
__/__
__/__
__/__
__/__
[0287]
Zone 87
__/__
__/__
__/__
__/__
- 11 -
[0263]
Zone 63
__/__
__/__
__/__
__/__
[0288]
Zone 88
__/__
__/__
__/__
__/__
[0264]
Zone 64
__/__
__/__
__/__
__/__
[0289]
Zone 89
__/__
__/__
__/__
__/__
[0265]
Zone 65
__/__
__/__
__/__
__/__
[0290]
Zone 90
__/__
__/__
__/__
__/__
[0266]
Zone 66
__/__
__/__
__/__
__/__
[0291]
Zone 91
__/__
__/__
__/__
__/__
[0267]
Zone 67
__/__
__/__
__/__
__/__
[0292]
Zone 92
__/__
__/__
__/__
__/__
[0268]
Zone 68
__/__
__/__
__/__
__/__
[0293]
Zone 93
__/__
__/__
__/__
__/__
[0269]
Zone 69
__/__
__/__
__/__
__/__
[0294]
Zone 94
__/__
__/__
__/__
__/__
[0270]
Zone 70
__/__
__/__
__/__
__/__
[0295]
Zone 95
__/__
__/__
__/__
__/__
[0271]
Zone 71
__/__
__/__
__/__
__/__
[0296]
Zone 96
__/__
__/__
__/__
__/__
Programming Guide
[0247]
Zone Labels
Section Zone #
Zone Label
Section Zone #
Zone Label
Section Zone #
Zone Label
Zone 1 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0306]
Zone 6 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0311] Zone 11 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0302]
Zone 2 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0307]
Zone 7 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0312] Zone 12 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0303]
Zone 3 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0308]
Zone 8 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0313] Zone 13 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0304]
Zone 4 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0309]
Zone 9 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0314] Zone 14 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0305]
Zone 5 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0310]
Zone 10 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0315] Zone 15 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0316] Zone 16 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0343]
Zone 43 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0370] Zone 70 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0317] Zone 17 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0344]
Zone 44 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0371] Zone 71 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0318] Zone 18 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0345]
Zone 45 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0372] Zone 72 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0319] Zone 19 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0346]
Zone 46 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0373] Zone 73 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0320] Zone 20 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0347]
Zone 47 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0374] Zone 74 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0321] Zone 21 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0348]
Zone 48 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0375] Zone 75 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0322] Zone 22 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0349]
Zone 49 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0376] Zone 76 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0323] Zone 23 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0350]
Zone 50 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0377] Zone 77 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0324] Zone 24 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0351]
Zone 51 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0378] Zone 78 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
- 12 -
[0325] Zone 25 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0352]
Zone 52 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0379] Zone 79 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0326] Zone 26 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0353]
Zone 53 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0380] Zone 80 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Programming Guide
[0327] Zone 27 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0354]
Zone 54 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0381] Zone 81 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0328] Zone 28 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0355]
Zone 55 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0382] Zone 82 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0329] Zone 29 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0356]
Zone 56 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0383] Zone 83 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0330] Zone 30 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0357]
Zone 57 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0384] Zone 84 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0331] Zone 31 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0358]
Zone 58 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0385] Zone 85 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0332] Zone 32 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0359]
Zone 59 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0386] Zone 86 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0333] Zone 33 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0360]
Zone 60 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0387] Zone 87 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0334] Zone 34 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0361]
Zone 61 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0388] Zone 88 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0335] Zone 35 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0362]
Zone 62 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0389] Zone 89 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0336] Zone 36 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0363]
Zone 63 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0390] Zone 90 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0337] Zone 37 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0364]
Zone 64 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0391] Zone 91 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0338] Zone 38 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0365]
Zone 65 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0392] Zone 92 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0339] Zone 39 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0366]
Zone 66 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0393] Zone 93 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0340] Zone 40 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0367]
Zone 67 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0394] Zone 94 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0341] Zone 41 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0368]
Zone 68 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0395] Zone 95 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0342] Zone 42 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0369]
Zone 69 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
[0396] Zone 96 __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Digiplex DGP-NE96
[0301]
Keyswitch Programming
Digiplex DGP-NE96
- 13 -
Keyswitch
1
Programming Guide
_______________________ _______________
Section
[0501]
8-digit Serial Number
___/___/___/___/___/___/___/___
Input#
___/___/___
Section
[0601]
2
_______________________ _______________
[0502]
___/___/___/___/___/___/___/___
___/___/___
[0602]
3
_______________________ _______________
[0503]
___/___/___/___/___/___/___/___
___/___/___
[0603]
4
_______________________ _______________
[0504]
___/___/___/___/___/___/___/___
___/___/___
[0604]
5
_______________________ _______________
[0505]
___/___/___/___/___/___/___/___
___/___/___
[0605]
6
_______________________ _______________
[0506]
___/___/___/___/___/___/___/___
___/___/___
[0606]
7
_______________________ _______________
[0507]
___/___/___/___/___/___/___/___
___/___/___
[0607]
8
_______________________ _______________
[0508]
___/___/___/___/___/___/___/___
___/___/___
[0608]
9
_______________________ _______________
[0509]
___/___/___/___/___/___/___/___
___/___/___
[0609]
10
_______________________ _______________
[0510]
___/___/___/___/___/___/___/___
___/___/___
[0610]
11
_______________________ _______________
[0511]
___/___/___/___/___/___/___/___
___/___/___
[0611]
12
_______________________ _______________
[0512]
___/___/___/___/___/___/___/___
___/___/___
[0612]
13
_______________________ _______________
[0513]
___/___/___/___/___/___/___/___
___/___/___
[0613]
14
_______________________ _______________
[0514]
___/___/___/___/___/___/___/___
___/___/___
[0614]
15
_______________________ _______________
[0515]
___/___/___/___/___/___/___/___
___/___/___
[0615]
16
_______________________ _______________
[0516]
___/___/___/___/___/___/___/___
___/___/___
[0616]
17
_______________________ _______________
[0517]
___/___/___/___/___/___/___/___
___/___/___
[0617]
18
_______________________ _______________
[0518]
___/___/___/___/___/___/___/___
___/___/___
[0618]
19
_______________________ _______________
[0519]
___/___/___/___/___/___/___/___
___/___/___
[0619]
20
_______________________ _______________
[0520]
___/___/___/___/___/___/___/___
___/___/___
[0620]
21
_______________________ _______________
[0521]
___/___/___/___/___/___/___/___
___/___/___
[0621]
_______________________ _______________
[0522]
___/___/___/___/___/___/___/___
___/___/___
[0622]
22
Description
Module
Define
Assign
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
Keyswitch Options
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
_______________________ _______________
Section
[0523]
8-digit Serial Number
___/___/___/___/___/___/___/___
Input#
___/___/___
Section
[0623]
_______________________ _______________
[0524]
___/___/___/___/___/___/___/___
___/___/___
[0624]
25
_______________________ _______________
[0525]
___/___/___/___/___/___/___/___
___/___/___
[0625]
26
_______________________ _______________
[0526]
___/___/___/___/___/___/___/___
___/___/___
[0626]
27
_______________________ _______________
[0527]
___/___/___/___/___/___/___/___
___/___/___
[0627]
28
_______________________ _______________
[0528]
___/___/___/___/___/___/___/___
___/___/___
[0628]
29
_______________________ _______________
[0529]
___/___/___/___/___/___/___/___
___/___/___
[0629]
30
_______________________ _______________
[0530]
___/___/___/___/___/___/___/___
___/___/___
[0630]
_______________________ _______________
[0531]
___/___/___/___/___/___/___/___
___/___/___
[0631]
Keyswitch
23
24
31
Description
Module
32
[0532]
___/___/___/___/___/___/___/___
___/___/___
_______________________ _______________
**If you wish to use this keyswitch definition, one or more PGMs must be programmed with the Utility Key event (Event Group #048; page 19).
[0632]
Define
Assign
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
___
Keyswitch Options
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
4 5 6 7 8
Digiplex DGP-NE96
Keyswitch Arming/Disarming Report Codes
Ademco slow, Silent Knight fast, SESCOA, Ademco express or Pager formats: Key-in desired 2-digit hex values from 00 to FF.
Ademco Contact ID:
Use section [4033] to program a set of default Ademco report codes from the Automatic Report Code Programming on page 41. Then to program the remaining report codes or to change some of the
defaults, enter the individual sections and key-in the desired 2-digit hex value found in the Contact ID Report Code List on page 44.
- 14 -
SIA format:
Use section [4033] to program a set of SIA report codes from the Automatic Report Code Programming on page 41. Codes that have not been set to default can be set to default manually by entering FF in
the appropriate section. To disable the reporting of an event, enter 00 in the appropriate section.
Arming With Keyswitch Report Codes
Programming Guide
Section
Section
Section
Section
Section
Section
[0701]
__/__ Keyswitch 01
[0707]
__/__ Keyswitch 07
[0713]
__/__ Keyswitch 13
[0719]
__/__ Keyswitch 19
[0725]
__/__ Keyswitch 25
[0731]
__/__ Keyswitch 31
[0702]
__/__ Keyswitch 02
[0708]
__/__ Keyswitch 08
[0714]
__/__ Keyswitch 14
[0720]
__/__ Keyswitch 20
[0726]
__/__ Keyswitch 26
[0732]
__/__ Keyswitch 32
[0703]
__/__ Keyswitch 03
[0709]
__/__ Keyswitch 09
[0715]
__/__ Keyswitch 15
[0721]
__/__ Keyswitch 21
[0727]
__/__ Keyswitch 27
[0704]
__/__ Keyswitch 04
[0710]
__/__ Keyswitch 10
[0716]
__/__ Keyswitch 16
[0722]
__/__ Keyswitch 22
[0728]
__/__ Keyswitch 28
[0705]
__/__ Keyswitch 05
[0711]
__/__ Keyswitch 11
[0717]
__/__ Keyswitch 17
[0723]
__/__ Keyswitch 23
[0729]
__/__ Keyswitch 29
[0706]
__/__ Keyswitch 06
[0712]
__/__ Keyswitch 12
[0718]
__/__ Keyswitch 18
[0724]
__/__ Keyswitch 24
[0730]
__/__ Keyswitch 30
Disarming With Keyswitch Report Codes
Section
Section
Section
Section
Section
Section
[0801]
__/__ Keyswitch 01
[0807]
__/__ Keyswitch 07
[0813]
__/__ Keyswitch 13
[0819]
__/__ Keyswitch 19
[0825]
__/__ Keyswitch 25
[0831]
__/__ Keyswitch 31
[0802]
__/__ Keyswitch 02
[0808]
__/__ Keyswitch 08
[0814]
__/__ Keyswitch 14
[0820]
__/__ Keyswitch 20
[0826]
__/__ Keyswitch 26
[0832]
__/__ Keyswitch 32
[0803]
__/__ Keyswitch 03
[0809]
__/__ Keyswitch 09
[0815]
__/__ Keyswitch 15
[0821]
__/__ Keyswitch 21
[0827]
__/__ Keyswitch 27
[0804]
__/__ Keyswitch 04
[0810]
__/__ Keyswitch 10
[0816]
__/__ Keyswitch 16
[0822]
__/__ Keyswitch 22
[0828]
__/__ Keyswitch 28
[0805]
__/__ Keyswitch 05
[0811]
__/__ Keyswitch 11
[0817]
__/__ Keyswitch 17
[0823]
__/__ Keyswitch 23
[0829]
__/__ Keyswitch 29
[0806]
__/__ Keyswitch 06
[0812]
__/__ Keyswitch 12
[0818]
__/__ Keyswitch 18
[0824]
__/__ Keyswitch 24
[0830]
__/__ Keyswitch 30
Programmable Outputs
PGM Test Mode
Section
Description
[0901]
Test PGM1: Activates PGM1 for 8 seconds to verify if the PGM is functioning correctly.
[0902]
Test PGM2: Activates PGM2 for 8 seconds to verify if the PGM is functioning correctly.
[0903]
Test PGM3: Activates PGM3 for 8 seconds to verify if the PGM is functioning correctly.
PGM Delay
Section
Data
Description
Default
[0918]
__/__/__ ( 001 to 255 x 1 sec./mins.)
PGM1 Delay (refer to section [0919] option [2] to see whether the delay is in seconds or minutes)
5 secs./mins.
[0928]
__/__/__ ( 001 to 255 x 1 sec./mins.)
PGM2 Delay (refer to section [0929] option [2] to see whether the delay is in seconds or minutes)
5 secs./mins.
[0938]
__/__/__ ( 001 to 255 x 1 sec./mins.)
PGM3 Delay (refer to section [0939] option [2] to see whether the delay is in seconds or minutes)
5 secs./mins.
PGM Options
PGM1
[0919]
Option
(
= Default Setting)
[1]
PGM Deactivation After (OFF = Deactivation Event;
[2]
PGM Base Time (OFF = Seconds;
[3]
Flexible PGM Deactivation Option (OFF = PGM Timer Only;
PGM2
[0929]
PGM3
[0939]
OFF
ON
OFF
ON
OFF
ON
Disabled
Enabled
Disabled
Enabled
Disabled
Enabled
ON = PGM Timer)
N
N
ON = Minutes)
N
N
ON = PGM Timer and/or Deactivation Event)
[4] to [8] Future Use
N/A
N
N
N
N
N/A
N/A
N/A
N
N/A
N/A
In order to use the Flexible PGM Deactivation Option (option [3]), the PGM Deactivation After Option (option [1]) must be ON.
PGM Programming
Event Group
Section
PGM Activation
PGM Deactivation
Event Group
Start #
Section
End #
Section
PGM1
[0910]
__/__/__
[0911]
__/__/__
[0912]
__/__/__
[0913]
__/__/__
PGM2
[0920]
__/__/__
[0921]
__/__/__
[0922]
__/__/__
[0923]
__/__/__
PGM3
[0930]
__/__/__
[0931]
__/__/__
[0932]
__/__/__
[0933]
__/__/__
PGM1
[0914]
__/__/__
[0915]
__/__/__
[0916]
__/__/__
[0917]
__/__/__
PGM2
[0924]
__/__/__
[0925]
__/__/__
[0926]
__/__/__
[0927]
__/__/__
PGM3
[0934]
__/__/__
[0935]
__/__/__
[0936]
__/__/__
[0937]
__/__/__
Event
000
Zone is OK
001
Zone is Open
002
Zone is Tampered
003
Zone is in Fire Loop Trouble
004
Feature Group
Section
Non-reportable Event
Feature Group
Feature
Start #
End #
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
TLM Trouble (See NOTE 3 on
page 21)
000
000
001
000
255 = any Zone #
Zone Numbers
000
Digiplex DGP-NE96
- 15 -
Smoke detector reset
001
Arm with no entry delay
002
002
Arm in Stay mode
003
003
004
Arm in Away mode
004
Full arm when in Stay mode
005
005
Voice module access
006
006
Remote control access
007
007
Programming Guide
Event Group
004
005
006
007
008
009
010
011
012
013
014
015
Event
Feature Group
Non-reportable Event (cont’d)
User Code entered on Keypad
User/Card Access on Door
Bypass Programming Access
TX Delay Zone Alarm
Arming with Master
Arming with User Code
Arming with Keyswitch
Special Arming
Disarm with Master
Disarm with User Code
Disarm with Keyswitch
000
Feature
Start #
End #
PC Fail to communicate
008
008
Midnight
009
009
NEware User Login
010
010
NEware User Logout
011
011
User Initiated Callup
012
012
Force Answer
013
013
Force Hangup
014
014
255
Any Non-reportable Event
Not Used
Not Used
000
User Codes 000 to 255
000 to 255
000 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Door Numbers
001 to 032
001 to 032
255
Any door #
Not Used
Not Used
000
One-touch Bypass Programming
000
000
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Zone Numbers
001 to 096
001 to 096
255
Any zone #
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Keyswitch numbers
001 to 032
001 to 032
255
Any keyswitch
Not Used
Not Used
Auto Arming
000
000
Arming with WinLoad
001
001
Late to Close
002
002
No Movement Arming
003
003
Partial Arming
004
004
One-touch Arming
005
005
Future Use
006
006
Future Use
007
007
(InTouch) Voice Module Arming
008
008
255
Any special arming event
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
000
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Keyswitch numbers
001 to 032
001 to 032
255
Any keyswitch
Not Used
Not Used
Digiplex DGP-NE96
- 16 -
Programming Guide
Event Group
016
017
018
019
020
021
022
Event
Disarm after alarm with Master
Disarm after alarm with User Code
Disarm after alarm with Keyswitch
Alarm Cancelled with Master
Alarm Cancelled with User Code
Alarm Cancelled with Keyswitch
Special Disarming
Feature Group
Feature
Start #
End #
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Keyswitch numbers
001 to 032
001 to 032
255
Any keyswitch
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Keyswitch numbers
001 to 032
001 to 032
255
Any keyswitch
Not Used
Not Used
Auto Arm Cancelled
000
000
One-touch Stay/Instant Disarm
001
001
Disarming with WinLoad
002
002
Disarming with WinLoad after alarm
003
003
WinLoad cancelled alarm
004
004
Future Use
005
005
Future Use
006
006
Future Use
007
007
(InTouch) Voice Module Disarming
008
008
000
255
023
Zone Bypassed
024
Zone in Alarm
025
Fire Alarm
026
Zone Alarm Restore
027
Fire Alarm Restore
Any Special Disarming Event
000
255 = any zone #
Zone Numbers
029
030
031
Early to Disarm by User
Late to Disarm by User
Special Alarm
Duress Alarm by User
Not Used
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
Emergency Panic (keys 1 & 3)
000
000
Medical Panic (keys 4 & 6)
001
001
Fire Panic (keys 7 & 9)
002
002
Recent Closing
003
003
Police Code
004
004
Zone Shutdown
005
005
255
Any Special Alarm Event
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
000
028
Not Used
001 to 096
000
Digiplex DGP-NE96
- 17 -
Programming Guide
Event Group
Event
031
Duress Alarm by User (cont’d)
032
Zone Shutdown
033
Zone Tamper
034
Zone Tamper Restore
035
Special Tamper
036
Feature Group
Feature
Start #
End #
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
000
000
TLM Trouble (see NOTE 2 on page 21)
000
000
AC Failure
001
001
Battery Failure
002
002
Auxiliary Current Limit
003
003
Bell Current Limit
004
004
Bell Absent
005
005
Clock Trouble
006
006
Global Fire Loop
007
007
Any Trouble Event
Not Used
Not Used
TLM Trouble (see NOTE 2 on page 21)
000
000
AC Failure
001
001
Battery Failure
002
002
Auxiliary Current Limit
003
003
Bell Current Limit
004
004
Bell Absent
005
005
Clock Trouble
006
006
000
Module Trouble
255
039
000
Module Trouble Restore
Fail to Communicate on Telephone
Number
041
Low Battery on Zone
042
Zone Supervision Trouble
043
Low Battery on Zone Restored
044
Zone Supervision Trouble Restored
045
Special Events
Global Fire Loop
007
007
Any Trouble Restore Event
Not Used
Not Used
Combus Fault
000
000
Module Tamper
001
001
ROM/RAM error
002
002
TLM Trouble
003
003
Fail to Communicate
004
004
Printer Fault
005
005
AC Failure
006
006
Battery Failure
007
007
Auxiliary Failure
008
008
Any Module Trouble Event
Not Used
Not Used
Combus Fault
000
000
Module Tamper
001
001
ROM/RAM error
002
002
TLM Trouble
003
003
Fail to Communicate
004
004
Printer Fault
005
005
AC Failure
006
006
Battery Failure
007
007
Auxiliary Failure
008
008
Any Module Trouble Restore Event
Not Used
Not Used
000
Telephone Number
001 to 004
001 to 004
255
Any telephone number
Not Used
Not Used
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
001 to 096
255
040
001 to 096
Keypad Lockout
255
038
001 to 096
001 to 096
000
000
Trouble Restore
001 to 096
Zone Numbers
255
037
Not Used
001 to 096
000
255 = any zone #
000
Trouble Event
Not Used
001 to 096
000
255 = any Zone #
Zone Numbers
Power up after total power down
000
000
Software reset (Watchdog)
001
001
000
255
Digiplex DGP-NE96
- 18 -
Test Report
002
002
Future Use
003
003
WinLoad In (connected)
004
004
WinLoad Out (disconnected)
005
005
Installer in programming
006
006
Installer out of programming
007
007
Any Special Event
Not Used
Not Used
Programming Guide
Event Group
046
047
Event
Early to Arm by User
Late to Arm by User
048
Utility Key
049
Request for Exit
050
Access Denied
051
Door Left Open Alarm
052
Door Forced Alarm
053
054
055
056 to 061
062
063
064
065
066
Feature Group
Feature
Start #
End #
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
Utility Key 001 to 064†*
001 to 064
001 to 064
255
Any Utility Key†*
Not Used
Not Used
001 to 032
001 to 032
001 to 032
001 to 032
001 to 032
001 to 032
001 to 032
001 to 032
Door Left Open Restore
001 to 032
001 to 032
Door Forced Open Restore
001 to 032
001 to 032
001 to 096
Intellizone Triggered
Future Use
Access Granted to User
Access Denied to User
Status 1
Status 2
Status 3
000
255 = any Door
Number
Door Numbers
000
Zone Numbers
001 to 096
255
Any zone number
Not Used
Not Used
Future Use
Future Use
Future Use
Future Use
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
000
User Codes 001 to 255
001 to 255
001 to 255
001
User Codes 256 to 511
000 to 255
000 to 255
002
User Codes 512 to 767
000 to 255
000 to 255
003
User Codes 768 to 999
000 to 231
000 to 231
255
Any User Code
Not Used
Not Used
Armed
000
000
Force Armed
001
001
Stay Armed
002
002
Instant Armed
003
003
See Note 1
on page 21
See Note 1
on page 21
See Note 1
on page 21
Strobe Alarm
004
004
Silent Alarm
005
005
Audible Alarm
006
006
Fire Alarm
007
007
Ready
000
000
Exit Delay
001
001
Entry Delay
002
002
System in Trouble
003
003
Alarm in Memory
004
004
Zones Bypassed
005
005
Bypass, Master, Installer Programming
006
006
Keypad Lockout
007
007
Intellizone Delay Engaged
(see Note 4 on page 21)
000
000
Fire Delay Engaged
001
001
Auto Arm
002
002
Arming with Voice Module (set until
Exit Delay finishes)
003
003
Tamper
004
004
†: See page 21
*: See page 21
Digiplex DGP-NE96
- 19 -
Programming Guide
Event Group
066
Event
Status 3 (cont’d)
Feature Group
See Note 1
on page 21
Feature
Start #
End #
Zone Low Battery
005
005
Fire Loop Trouble
006
006
Zone Supervision Trouble
007
007
000 to 003
000 to 003
Smoke Detector Power Reset
004
004
Ground Start
005
005
Kiss Off
006
006
Telephone Ring
007
007
008 to 015
008 to 015
016 to 023
016 to 023
024 to 031
024 to 031
032 to 063
032 to 063
064 to 095
064 to 095
Chime in Partition 1 to 4
(000 to 003 = System 1 to 4)
Bell on Partition 1 to 8
(008 to 015 = Partitions 1 to 8)
Fire Alarm in Partition 1 to 8
(016 to 023 = Partitions 1 to 8)
Open/close Kiss Off in Partition 1 to 8
(024 to 031 = Partitions 1 to 8)
Keyswitch/PGM Inputs # 01 to 32
(032 to 063 = Keyswitch/PGM Inputs # 01 to 32)
Status of Access Door 01 to 32
(064 to 095 = Access Doors 01 to 32)
067
Special Status
Trouble in System
096
096
Trouble in Dialer
097
097
Trouble in Module
098
098
Trouble in Combus
099
099
Future Use
100 to 102
100 to 102
Time and Date Trouble
103
103
AC Failure
104
104
Battery Failure
105
105
Auxiliary Current Limit
106
106
Bell Current Limit
107
107
Bell Absent
108
108
ROM error
109
109
110
N/A
RAM error
110
Future Use
111
111
TLM 1 Trouble
112
112
Fail to Communicate 1
113
113
Fail to Communicate 2
114
114
Fail to Communicate 3
115
115
Fail to Communicate 4
116
116
Fail to Communicate with PC
117
117
Future Use
118
118
Future Use
119
119
Module Tamper Trouble
120
120
Module ROM error
121
121
Module TLM error
122
122
Module Failure to Communicate
123
123
Module Printer Trouble
124
124
Module AC Failure
125
125
Module Battery Trouble
126
126
Module Auxiliary Failure
127
127
Missing Keypad
128
128
Missing Module
129
129
Future Use
130 to 132
130 to 132
Global Combus Failure
133
133
Combus Overload
134
134
Combus Fail to Communicate
070
NOTE 1:
Clock
N/A
000 = Occurs in all partitions enabled in the system (see section [3031]).
001 = Partition 1 003 = Partition 3 005 = Partition 5 007 = Partition 7
002 = Partition 2 004 = Partition 4 006 = Partition 6 008 = Partition 8
Digiplex DGP-NE96
- 20 -
135
135
Hour
Minutes
255 = Occurs in at least one partition enabled in the system.
Programming Guide
NOTE 2:
The TLM trouble event can only be used with DGP-NE96 control panel models that have two dialers.
NOTE 3:
The TLM trouble event can only be used with DGP-NE96 control panel models that have one dialer.
NOTE 4:
This event cannot be used for a module’s PGM programming.
*:
If a Keyswitch Input is used, the input must be defined as “Generates a Utility Key Event on Open” or “Generates a Utility Key Event on Open
and Close”. If a remote control is used, the remote control button must be defined as a Utility Key button.
†:
Actions that Activate a Utility Key Event:
Actions
Utility Key Event
Keypad Utility Keys
Keyswitch Inputs
(definition = [3])
Keyswitch Inputs
(definition = [4])
Remote Control
Utility Key Event 1
[1] & [2]
KS** Input 1 opens
KS** Input 1 opens
Utility Key 1 RC button‡
Utility Key Event 2
[4] & [5]
KS** Input 2 opens
KS** Input 1 closes
Utility Key 2 RC button‡
Utility Key Event 3
[7] & [8]
KS** Input 3 opens
KS** Input 2 opens
Utility Key 3 RC button‡
Utility Key Event 4
[CLEAR] & [0] or [*] & [0]
KS** Input 4 opens
KS** Input 2 closes
Utility Key 4 RC button‡
Utility Key Event 5
[2] & [3]
KS** Input 5 opens
KS** Input 3 opens
Utility Key 5 RC button‡
Utility Key Event 6
[5] & [6]
KS** Input 6 opens
KS** Input 3 closes
N/A
Utility Key Event 7
[8] & [9]
KS** Input 7 opens
KS** Input 4 opens
N/A
Utility Key Event 8
[0] & [ENTER] or [0] & [#]
KS** Input 8 opens
KS** Input 4 closes
N/A
Utility Key Event 9
N/A
KS** Input 9 opens
KS** Input 5 opens
N/A
Utility Key Event 10
N/A
KS** Input 10 opens
KS** Input 5 closes
N/A
Utility Key Event 11
N/A
KS** Input 11 opens
KS** Input 6 opens
N/A
Utility Key Event 12
N/A
KS** Input 12 opens
KS** Input 6 closes
N/A
Utility Key Event 13
N/A
KS** Input 13 opens
KS** Input 7 opens
N/A
Utility Key Event 14
N/A
KS** Input 14 opens
KS** Input 7 closes
N/A
Utility Key Event 15
N/A
KS** Input 15 opens
KS** Input 8 opens
N/A
Utility Key Event 16
N/A
KS** Input 16 opens
KS** Input 8 closes
N/A
Utility Key Event 17
N/A
KS** Input 17 opens
KS** Input 9 opens
N/A
Utility Key Event 18
N/A
KS** Input 18 opens
KS** Input 9 closes
N/A
N/A
KS** Input 31 opens
KS** Input 16 opens
N/A
Utility Key Event 32
N/A
KS** Input 32 opens
KS** Input 16 closes
N/A
Utility Key Event 33
N/A
N/A
KS** Input 17 opens
N/A
Utility Key Event 34
N/A
N/A
KS** Input 17 closes
N/A
N/A
Utility Key Event 31
N/A
N/A
N/A
Utility Key Event 63
N/A
N/A
KS** Input 32 opens
N/A
N/A
Utility Key Event 64
N/A
N/A
KS** Input 32 closes
N/A
** Keyswitch
‡ Refer
to the MG-RCV3 Reference and Installation Manual for remote control button programming instructions.
Digiplex DGP-NE96
- 21 -
Programming Guide
Input Speeds
Section
Data - Decimal Value (001 - 255)
Description
Default
[0961]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 01
600 msec.
[0962]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 02
600 msec.
[0963]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 03
600 msec.
[0964]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 04
600 msec.
[0965]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 05
600 msec.
[0966]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 06
600 msec.
[0967]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 07
600 msec.
[0968]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 08
600 msec.
[0969]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 09 (DGP2-ZX4 INPUT 01)
600 msec.
[0970]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 10 (DGP2-ZX4 INPUT 02)
600 msec.
[0971]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 11 (DGP2-ZX4 INPUT 03)
600 msec.
[0972]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 12 (DGP2-ZX4 INPUT 04)
600 msec.
[0973]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 13 (ATZ OF INPUT 01)
600 msec.
[0974]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 14 (ATZ OF INPUT 02)
600 msec.
[0975]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 15 (ATZ OF INPUT 03)
600 msec.
[0976]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 16 (ATZ OF INPUT 04)
600 msec.
[0977]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 17 (ATZ OF INPUT 05)
600 msec.
[0978]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 18 (ATZ OF INPUT 06)
600 msec.
[0979]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 19 (ATZ OF INPUT 07)
600 msec.
[0980]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 20 (ATZ OF INPUT 08)
600 msec.
[0981]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 21 (ATZ OF DGP2-ZX4 INPUT 01)
600 msec.
[0982]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 22 (ATZ OF DGP2-ZX4 INPUT 02)
600 msec.
[0983]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 23 (ATZ OF DGP2-ZX4 INPUT 03)
600 msec.
[0984]
__/__/__ (001 to 255) x 30 msec.
INPUT SPEED OF INPUT 24 (ATZ OF DGP2-ZX4 INPUT 04)
600 msec.
Installer Code Programming
Section
[1000]
Data
Description
Default
__/__/__/__/__/__
INSTALLER CODE
(REFER TO SECTION [3001], Installer lock ON PAGE 29)
000000
Digiplex DGP-NE96
- 22 -
Programming Guide
User Code Options
Sections [1001] to [1999]
The instructions that follow detail how to program access codes when using an LCD keypad. Program User Code Options, Partition Assignment and Access
Control features for users 001 to 999. Refer to the appropriate keypad User’s Manual for instructions on how certain users can program these values. For
instructions on how to program users when using a Grafica keypad, refer to Grafica’s User Manual. A complete Grafica User Manual is available on our Web
site at www.paradox.ca.
To program user labels, refer to the LCD Keypad System Manager’s Manual.
Digiplex DGP-NE96
- 23 -
Programming Guide
Arming and Disarming Report Codes
Ademco slow, Silent Knight fast, SESCOA, Ademco express or Pager formats:
Key-in desired 2-digit hex values from 00 to FF.
Ademco format:
Use section [4033] to program a set of default Ademco report codes from the Automatic Report Code Programming on page 41. Then to program the
remaining report codes or to change some of the defaults, enter the individual sections and key-in the desired 2-digit hex value found in the Contact ID
Report Code List on page 44.
SIA format:
Use section [4033] to program a set of SIA report codes from the Automatic Report Code Programming on page 41. Codes that have not been set to default
can be set to default manually by entering FF in the appropriate section. To disable the reporting of an event, enter 00 in the appropriate section.
Arming Report Codes
Section
Section
Section
Section
[2001]
__/__ Access Code 1
[2026]
__/__ Access Code 26
[2051]
__/__ Access Code 51
[2076]
__/__ Access Code 76
[2002]
__/__ Access Code 2
[2027]
__/__ Access Code 27
[2052]
__/__ Access Code 52
[2077]
__/__ Access Code 77
[2003]
__/__ Access Code 3
[2028]
__/__ Access Code 28
[2053]
__/__ Access Code 53
[2078]
__/__ Access Code 78
[2004]
__/__ Access Code 4
[2029]
__/__ Access Code 29
[2054]
__/__ Access Code 54
[2079]
__/__ Access Code 79
[2005]
__/__ Access Code 5
[2030]
__/__ Access Code 30
[2055]
__/__ Access Code 55
[2080]
__/__ Access Code 80
[2006]
__/__ Access Code 6
[2031]
__/__ Access Code 31
[2056]
__/__ Access Code 56
[2081]
__/__ Access Code 81
[2007]
__/__ Access Code 7
[2032]
__/__ Access Code 32
[2057]
__/__ Access Code 57
[2082]
__/__ Access Code 82
[2008]
__/__ Access Code 8
[2033]
__/__ Access Code 33
[2058]
__/__ Access Code 58
[2083]
__/__ Access Code 83
[2009]
__/__ Access Code 9
[2034]
__/__ Access Code 34
[2059]
__/__ Access Code 59
[2084]
__/__ Access Code 84
[2010]
__/__ Access Code 10
[2035]
__/__ Access Code 35
[2060]
__/__ Access Code 60
[2085]
__/__ Access Code 85
[2011]
__/__ Access Code 11
[2036]
__/__ Access Code 36
[2061]
__/__ Access Code 61
[2086]
__/__ Access Code 86
[2012]
__/__ Access Code 12
[2037]
__/__ Access Code 37
[2062]
__/__ Access Code 62
[2087]
__/__ Access Code 87
[2013]
__/__ Access Code 13
[2038]
__/__ Access Code 38
[2063]
__/__ Access Code 63
[2088]
__/__ Access Code 88
[2014]
__/__ Access Code 14
[2039]
__/__ Access Code 39
[2064]
__/__ Access Code 64
[2089]
__/__ Access Code 89
[2015]
__/__ Access Code 15
[2040]
__/__ Access Code 40
[2065]
__/__ Access Code 65
[2090]
__/__ Access Code 90
[2016]
__/__ Access Code 16
[2041]
__/__ Access Code 41
[2066]
__/__ Access Code 66
[2091]
__/__ Access Code 91
[2017]
__/__ Access Code 17
[2042]
__/__ Access Code 42
[2067]
__/__ Access Code 67
[2092]
__/__ Access Code 92
[2018]
__/__ Access Code 18
[2043]
__/__ Access Code 43
[2068]
__/__ Access Code 68
[2093]
__/__ Access Code 93
[2019]
__/__ Access Code 19
[2044]
__/__ Access Code 44
[2069]
__/__ Access Code 69
[2094]
__/__ Access Code 94
[2020]
__/__ Access Code 20
[2045]
__/__ Access Code 45
[2070]
__/__ Access Code 70
[2095]
__/__ Access Code 95
[2021]
__/__ Access Code 21
[2046]
__/__ Access Code 46
[2071]
__/__ Access Code 71
[2096]
__/__ Access Code 96
[2022]
__/__ Access Code 22
[2047]
__/__ Access Code 47
[2072]
__/__ Access Code 72
[2097]
__/__ Access Code 97
[2023]
__/__ Access Code 23
[2048]
__/__ Access Code 48
[2073]
__/__ Access Code 73
[2098]
__/__ Access Code 98
[2024]
__/__ Access Code 24
[2049]
__/__ Access Code 49
[2074]
__/__ Access Code 74
[2099]
[2025]
__/__ Access Code 25
[2050]
__/__ Access Code 50
[2075]
__/__ Access Code 75
__/__ Access Codes
99 to 999
Disarming Report Codes
Section
Section
Section
Section
[2101]
__/__ Access Code 1
[2107]
__/__ Access Code 7
[2113]
__/__ Access Code 13
[2119]
__/__ Access Code 19
[2102]
__/__ Access Code 2
[2108]
__/__ Access Code 8
[2114]
__/__ Access Code 14
[2120]
__/__ Access Code 20
[2103]
__/__ Access Code 3
[2109]
__/__ Access Code 9
[2115]
__/__ Access Code 15
[2121]
__/__ Access Code 21
[2104]
__/__ Access Code 4
[2110]
__/__ Access Code 10
[2116]
__/__ Access Code 16
[2122]
__/__ Access Code 22
[2105]
__/__ Access Code 5
[2111]
__/__ Access Code 11
[2117]
__/__ Access Code 17
[2123]
__/__ Access Code 23
[2106]
__/__ Access Code 6
[2112]
__/__ Access Code 12
[2118]
__/__ Access Code 18
[2124]
__/__ Access Code 24
[2125]
__/__ Access Code 25
[2144]
__/__ Access Code 44
[2163]
__/__ Access Code 63
[2182]
__/__ Access Code 82
Digiplex DGP-NE96
- 24 -
Programming Guide
[2126]
__/__ Access Code 26
[2145]
__/__ Access Code 45
[2164]
__/__ Access Code 64
[2183]
__/__ Access Code 83
[2127]
__/__ Access Code 27
[2146]
__/__ Access Code 46
[2165]
__/__ Access Code 65
[2184]
__/__ Access Code 84
[2128]
__/__ Access Code 28
[2147]
__/__ Access Code 47
[2166]
__/__ Access Code 66
[2185]
__/__ Access Code 85
[2129]
__/__ Access Code 29
[2148]
__/__ Access Code 48
[2167]
__/__ Access Code 67
[2186]
__/__ Access Code 86
[2130]
__/__ Access Code 30
[2149]
__/__ Access Code 49
[2168]
__/__ Access Code 68
[2187]
__/__ Access Code 87
[2131]
__/__ Access Code 31
[2150]
__/__ Access Code 50
[2169]
__/__ Access Code 69
[2188]
__/__ Access Code 88
[2132]
__/__ Access Code 32
[2151]
__/__ Access Code 51
[2170]
__/__ Access Code 70
[2189]
__/__ Access Code 89
[2133]
__/__ Access Code 33
[2152]
__/__ Access Code 52
[2171]
__/__ Access Code 71
[2190]
__/__ Access Code 90
[2134]
__/__ Access Code 34
[2153]
__/__ Access Code 53
[2172]
__/__ Access Code 72
[2191]
__/__ Access Code 91
[2135]
__/__ Access Code 35
[2154]
__/__ Access Code 54
[2173]
__/__ Access Code 73
[2192]
__/__ Access Code 92
[2136]
__/__ Access Code 36
[2155]
__/__ Access Code 55
[2174]
__/__ Access Code 74
[2193]
__/__ Access Code 93
[2137]
__/__ Access Code 37
[2156]
__/__ Access Code 56
[2175]
__/__ Access Code 75
[2194]
__/__ Access Code 94
[2138]
__/__ Access Code 38
[2157]
__/__ Access Code 57
[2176]
__/__ Access Code 76
[2195]
__/__ Access Code 95
[2139]
__/__ Access Code 39
[2158]
__/__ Access Code 58
[2177]
__/__ Access Code 77
[2196]
__/__ Access Code 96
[2140]
__/__ Access Code 40
[2159]
__/__ Access Code 59
[2178]
__/__ Access Code 78
[2197]
__/__ Access Code 97
[2141]
__/__ Access Code 41
[2160]
__/__ Access Code 60
[2179]
__/__ Access Code 79
[2198]
__/__ Access Code 98
[2142]
__/__ Access Code 42
[2161]
__/__ Access Code 61
[2180]
__/__ Access Code 80
[2199]
[2143]
__/__ Access Code 43
[2162]
__/__ Access Code 62
[2181]
__/__ Access Code 81
__/__ Access Codes
99 to 999
Access Control Sections
Assigning a Door to the System
These doors are used to program the Access Levels in sections [2601] to [2615]. If you want a door to be linked to the alarm system, install a door contact
and assign it to a zone through Zone Programming. Note: Under the Door Numbering column (see below), enter the 8-digit serial number of the
DGP2-ACM1P.
Door Numbering
Door Labels
Door Options
Door #
Section
Serial Number
Section
Option
Section
Label
Door 01
[2201]
__/__/__/__/__/__/__/__
[2251]
1 2 3 4 5 * * *
[2301]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 02
[2202]
__/__/__/__/__/__/__/__
[2252]
1 2 3 4 5 * * *
[2302]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 03
[2203]
__/__/__/__/__/__/__/__
[2253]
1 2 3 4 5 * * *
[2303]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 04
[2204]
__/__/__/__/__/__/__/__
[2254]
1 2 3 4 5 * * *
[2304]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 05
[2205]
__/__/__/__/__/__/__/__
[2255]
1 2 3 4 5 * * *
[2305]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 06
[2206]
__/__/__/__/__/__/__/__
[2256]
1 2 3 4 5 * * *
[2306]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 07
[2207]
__/__/__/__/__/__/__/__
[2257]
1 2 3 4 5 * * *
[2307]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 08
[2208]
__/__/__/__/__/__/__/__
[2258]
1 2 3 4 5 * * *
[2308]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 09
[2209]
__/__/__/__/__/__/__/__
[2259]
1 2 3 4 5 * * *
[2309]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 10
[2210]
__/__/__/__/__/__/__/__
[2260]
1 2 3 4 5 * * *
[2310]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 11
[2211]
__/__/__/__/__/__/__/__
[2261]
1 2 3 4 5 * * *
[2311]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 12
[2212]
__/__/__/__/__/__/__/__
[2262]
1 2 3 4 5 * * *
[2312]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 13
[2213]
__/__/__/__/__/__/__/__
[2263]
1 2 3 4 5 * * *
[2313]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 14
[2214]
__/__/__/__/__/__/__/__
[2264]
1 2 3 4 5 * * *
[2314]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 15
[2215]
__/__/__/__/__/__/__/__
[2265]
1 2 3 4 5 * * *
[2315]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 16
[2216]
__/__/__/__/__/__/__/__
[2266]
1 2 3 4 5 * * *
[2316]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 17
[2217]
__/__/__/__/__/__/__/__
[2267]
1 2 3 4 5 * * *
[2317]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 18
[2218]
__/__/__/__/__/__/__/__
[2268]
1 2 3 4 5 * * *
[2318]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 19
[2219]
__/__/__/__/__/__/__/__
[2269]
1 2 3 4 5 * * *
[2319]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Digiplex DGP-NE96
- 25 -
Programming Guide
Door 20
[2220]
__/__/__/__/__/__/__/__
[2270]
1 2 3 4 5 * * *
[2320]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 21
[2221]
__/__/__/__/__/__/__/__
[2271]
1 2 3 4 5 * * *
[2321]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 22
[2222]
__/__/__/__/__/__/__/__
[2272]
1 2 3 4 5 * * *
[2322]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 23
[2223]
__/__/__/__/__/__/__/__
[2273]
1 2 3 4 5 * * *
[2323]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 24
[2224]
__/__/__/__/__/__/__/__
[2274]
1 2 3 4 5 * * *
[2324]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 25
[2225]
__/__/__/__/__/__/__/__
[2275]
1 2 3 4 5 * * *
[2325]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 26
[2226]
__/__/__/__/__/__/__/__
[2276]
1 2 3 4 5 * * *
[2326]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 27
[2227]
__/__/__/__/__/__/__/__
[2277]
1 2 3 4 5 * * *
[2327]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 28
[2228]
__/__/__/__/__/__/__/__
[2278]
1 2 3 4 5 * * *
[2328]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 29
[2229]
__/__/__/__/__/__/__/__
[2279]
1 2 3 4 5 * * *
[2329]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 30
[2230]
__/__/__/__/__/__/__/__
[2280]
1 2 3 4 5 * * *
[2330]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 31
[2231]
__/__/__/__/__/__/__/__
[2281]
1 2 3 4 5 * * *
[2331]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door 32
[2232]
__/__/__/__/__/__/__/__
[2282]
1 2 3 4 5 * * *
[2332]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__
Door Options:[1] “OR/AND” Door Access - Each door can be programmed to grant access only to cards assigned to at least one of the door’s partitions (“OR” Door Access) or to cards assigned to all the
door’s assigned partitions (“AND” Door Access). Enabling option [1] will set the door in “OR” Door Access Mode. Disabling option [1] will set the door in “AND” Door Access Mode.
[2] User Code Access - When option [2] is disabled, the access control door is accessed through the reader by presenting the access card to the reader. When option [2] is enabled, a reader
is not needed to access the controlled door. To access the controlled door, the user must enter their access code and then press the [ACC] button. (DGP2-641 only)
[3] Card and Code Access - Enabling option [3] will require that both a valid access control card and a valid user access code be used. The access control card and user access code must
belong to the same user. Disabling option [3] requires that either a valid access control card or a valid user access code be used to access the controlled door. (PosiPIN™ reader only)
[4] Restrict Arming on Door - When option [4] is enabled, that door’s reader cannot be used to arm the system even if the access control card has the arming option enabled.
[5] Restrict Disarming on Door - When option [5] is enabled, that door’s reader cannot be used to disarm the system even if the access control card has the disarming option enabled.
Schedule Programming
Each Schedule determines when users are permitted access. Schedules 001 and 015 (sections [2401] to [2415]) are Primary Schedules. The Primary
Schedules are the only schedules that can be assigned to a User Access Code. Schedules 016 to 032 (sections [2416] to [2432]) are Secondary Schedules.
The Secondary Schedules cannot be assigned to a User Access Code and can only be used as backup schedules.
Section
[2401]
[2402]
[2403]
[2404]
PRIMARY SCHEDULES
[2405]
[2406]
[2407]
[2408]
[2409]
[2410]
[2411]
[2412]
[2413]
Schedule
001
002
003
004
005
006
007
008
009
010
011
012
013
Intervals
Start Time (from)
End Time (to)
Days (turn ON or OFF)
S M T W
T
F S H
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Digiplex DGP-NE96
- 26 -
Programming Guide
PRIMARY SCHEDULES
Section
[2414]
[2415]
[2416]
[2417]
[2418]
[2419]
[2420]
[2421]
SECONDARY SCHEDULES
[2422]
[2423]
[2424]
[2425]
[2426]
[2427]
[2428]
[2429]
[2430]
[2431]
[2432]
Schedule
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
Intervals
Start Time (from)
End Time (to)
Days (turn ON or OFF)
S M T W
T
F S H
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
The Start and End Time of a schedule cannot cross over into another day. For example, to program a shift from 10PM one day to 6AM the
next morning, you must program Schedule A: Start Time 22:00 and End Time 23:59 then program Schedule B Start Time 00:00 and End
Time 06:00. The schedule will not be interrupted between 23:59 and 00:00.
Digiplex DGP-NE96
- 27 -
Programming Guide
Backup Schedules
Each programmed schedule (see Schedule Programming on page 26) can be backed up or linked to another schedule. The backup will be used in the event
that the first schedule is invalid. Enter the 3-digit number of the schedule you wish to use as the backup. Ex: You wish to backup schedule 001 to schedule
011. In section [2501], you would enter 011.
The control panel will verify up to 8 linked schedules, one after another, until it determines whether the card or code is valid. Ex: If Schedule 001 is linked to
Schedule 005 and Schedule 005 is linked to Schedule 030, then the control panel will verify Schedules 001, 005 and 030.
Section
Section
Section
Section
[2501]
__/__/__ Schedule 001
[2509]
__/__/__ Schedule 009
[2517]
__/__/__ Schedule 017
[2525]
__/__/__ Schedule 025
[2502]
__/__/__ Schedule 002
[2510]
__/__/__ Schedule 010
[2518]
__/__/__ Schedule 018
[2526]
__/__/__ Schedule 026
[2503]
__/__/__ Schedule 003
[2511]
__/__/__ Schedule 011
[2519]
__/__/__ Schedule 019
[2527]
__/__/__ Schedule 027
[2504]
__/__/__ Schedule 004
[2512]
__/__/__ Schedule 012
[2520]
__/__/__ Schedule 020
[2528]
__/__/__ Schedule 028
[2505]
__/__/__ Schedule 005
[2513]
__/__/__ Schedule 013
[2521]
__/__/__ Schedule 021
[2529]
__/__/__ Schedule 029
[2506]
__/__/__ Schedule 006
[2514]
__/__/__ Schedule 014
[2522]
__/__/__ Schedule 022
[2530]
__/__/__ Schedule 030
[2507]
__/__/__ Schedule 007
[2515]
__/__/__ Schedule 015
[2523]
__/__/__ Schedule 023
[2531]
__/__/__ Schedule 031
[2508]
__/__/__ Schedule 008
[2516]
__/__/__ Schedule 016
[2524]
__/__/__ Schedule 024
[2532]
__/__/__ Schedule 032
Programming Access Levels
Each Access Level is a combination of Access Control doors. For example, if option [1] in the First Screen is enabled in section [2601], Level 01 will allow
access only to Door 01.
Section
Level
Access to Doors (turn ON or OFF access):
First Screen
Doors 01 to 08
Second Screen
Doors 09 to 16
Third Screen
Doors 17 to 24
Fourth Screen
Doors 25 to 32
[2601]
01
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
[2602]
02
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
[2603]
03
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
[2604]
04
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
[2605]
05
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
[2606]
06
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
[2607]
07
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
[2608]
08
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
[2609]
09
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
[2610]
10
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
[2611]
11
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
[2612]
12
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
[2613]
13
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
[2614]
14
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
[2615]
15
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Holiday Programming
When [H] is enabled in a schedule (refer to page 26), access is permitted to users during the days programmed in the sections below.
Section
Month
Days
First Screen
Days 01 to 08
Second Screen
Days 09 to 16
Third Screen
Days 17 to 24
Fourth Screen
Days 25 to 31
[2701]
January
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7*
[2702]
February
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7*
[2703]
March
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7*
[2704]
April
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7*
[2705]
May
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7*
[2706]
June
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7*
[2707]
July
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7*
[2708]
August
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7*
[2709]
September
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7*
[2710]
October
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7*
[2711]
November
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7*
[2712]
December
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7*
Digiplex DGP-NE96
- 28 -
Programming Guide
Keypad Numbering
Sections [2801] to [2832] are used solely for the purpose of identifying a keypad in the event buffer. Enter the 8-digit serial number of the keypad you wish to
label as keypad x (1 to 32). The event buffer will then display any events pertaining to a keypad as keypad 1 or keypad 2, etc.
Section
Keypad #
Serial Number
Section
Keypad #
Serial Number
Section
Keypad #
Serial Number
[2801]
Keypad 1
__/__/__/__/__/__/__/__
[2812]
Keypad 12 __/__/__/__/__/__/__/__
[2823]
Keypad 23 __/__/__/__/__/__/__/__
[2802]
Keypad 2
__/__/__/__/__/__/__/__
[2813]
Keypad 13 __/__/__/__/__/__/__/__
[2824]
Keypad 24 __/__/__/__/__/__/__/__
[2803]
Keypad 3
__/__/__/__/__/__/__/__
[2814]
Keypad 14 __/__/__/__/__/__/__/__
[2825]
Keypad 25 __/__/__/__/__/__/__/__
[2804]
Keypad 4
__/__/__/__/__/__/__/__
[2815]
Keypad 15 __/__/__/__/__/__/__/__
[2826]
Keypad 26 __/__/__/__/__/__/__/__
[2805]
Keypad 5
__/__/__/__/__/__/__/__
[2816]
Keypad 16 __/__/__/__/__/__/__/__
[2827]
Keypad 27 __/__/__/__/__/__/__/__
[2806]
Keypad 6
__/__/__/__/__/__/__/__
[2817]
Keypad 17 __/__/__/__/__/__/__/__
[2828]
Keypad 28 __/__/__/__/__/__/__/__
[2807]
Keypad 7
__/__/__/__/__/__/__/__
[2818]
Keypad 18 __/__/__/__/__/__/__/__
[2829]
Keypad 29 __/__/__/__/__/__/__/__
[2808]
Keypad 8
__/__/__/__/__/__/__/__
[2819]
Keypad 19 __/__/__/__/__/__/__/__
[2830]
Keypad 30 __/__/__/__/__/__/__/__
[2809]
Keypad 9
__/__/__/__/__/__/__/__
[2820]
Keypad 20 __/__/__/__/__/__/__/__
[2831]
Keypad 31 __/__/__/__/__/__/__/__
[2810]
Keypad 10 __/__/__/__/__/__/__/__
[2821]
Keypad 21 __/__/__/__/__/__/__/__
[2832]
Keypad 32 __/__/__/__/__/__/__/__
[2811]
Keypad 11 __/__/__/__/__/__/__/__
[2822]
Keypad 22 __/__/__/__/__/__/__/__
Control Panel Settings
Section
Data
Description
Default
[3001]
__/__/__ (147 = Locked, 000 = Unlocked)
INSTALLER LOCK
000
[3010]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ PC PHONE NUMBER (32 DIGITS)
[3011]
__/__/__/__
PANEL IDENTIFICATION
0000
[3012]
__/__/__/__
PC PASSWORD
0000
[3020]
__/__
PANEL PARTITION (00 - 08)
00
[3021]
__/__
TROUBLE SHUTDOWN (00 - 15)
00
System Options
= Default setting
SECTION [3030] : System Options 1
SECTION [3031] : Partition Options 1
OFF
Option
ON
[1]
PGM 1 = 2-wire smoke detector
input (255)
Disabled
N Enabled
[2]
No bell cut-off during fire alarm
Disabled
N Enabled
[3]
Daylight saving time
[4]
Shabbat feature
Disabled
N Enabled
[5]
Battery charge current
350mA
[6]
AC failure not displayed as trouble
Disabled
[7]
Clear bell limit trouble
On restore
[8]
Combus Speed*
Normal
N Disabled
OFF
Option
Enabled
N 850mA†
N Enabled
N Manually
N High
[1]
Partition 1
N Disabled
[2]
Partition 2
Disabled
[3]
Partition 3
Disabled
[4]
Partition 4
Disabled
[5]
Partition 5
Disabled
[6]
Partition 6
Disabled
[7]
Partition 7
Disabled
[8]
Partition 8
Disabled
ON
Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
* Please note that when the Combus Speed is changed, all operations on the system will be suspended for approximately 1 minute while
the system configures itself.
† A 40VA transformer is required when selecting the 850mA battery charge current. Using a 20VA transformer with a battery charge
current of 850mA may damage the system.
Digiplex DGP-NE96
- 29 -
Programming Guide
= Default setting
SECTION [3032] : Partition Options 2
SECTION [3033] : System Options 2
OFF
Option
ON
[1]
Bell/siren output in partition 1
N Disabled
[2]
Bell/siren output in partition 2
Disabled
[3]
Bell/siren output in partition 3
Disabled
[4]
Bell/siren output in partition 4
Disabled
Bell/siren output in partition 5
Disabled
N Enabled
N Enabled
[5]
[6]
Bell/siren output in partition 6
Disabled
Bell/siren output in partition 7
Disabled
[8]
Bell/siren output in partition 8
Disabled
[1]
Multiple actions in user menu
Disabled
[2]
User code length
Fixed
N Enabled
[3]
User code length (if option [2] OFF)
[4]
Power save mode
[5]
Bypass not displayed while system
is armed
[6]
Trouble Latch
Disabled
[7]
EOL resistor on hardwire zones
Disabled
[8]
(ATZ) Zone Doubling
Disabled
N Enabled
N Enabled
N Enabled
SECTION [3034] : System Options 3
ON
[3]
Generate supervision failure if
detected on a bypassed wireless zone
Yes
N No
[4]
Restrict arming on a wireless
transmitter supervision failure
Disabled
N Enabled
[5]&[6] Zone & Module Tamper Recognition
Options (see table below)
[8]
Restrict arming on tamper trouble
N 6-digits
4-digits
N Disabled
Enabled
N Disabled
Enabled
N See Table N See Table
N See Table N See Table
NYes
No
Disabled
OFF
Option
N See Table N See Table
N See Table N See Table
[1]&[2] Wireless Transmitter Supervision
Options (see table below)
Generate tamper if detected on
bypass zone
N Enabled
N Flexible
N Enabled
N Enabled
N Enabled
SECTION [3035] : System Options 4
OFF
Option
[7]
ON
N Enabled
Enabled
[7]
OFF
Option
N Enabled
ON
[1]
Restrict arming on AC failure
Disabled
N Enabled
[2]
Restrict arming on battery failure
Disabled
N Enabled
[3]
Restrict arming on bell or auxiliary
failure
Disabled
N Enabled
[4]
Restrict arming on TLM failure
Disabled
N Enabled
[5]
Restrict arming on module
troubles
Disabled
N Enabled
[6]
Account Number Transmission
Partition #
[7]
Transmit zone status on serial port
Disabled
N Enabled
[8]
Serial Port Baud Rate
19,200
N 38,400
N Tel #
Wireless Transmitter Supervision Options
Zone & Module Tamper Recognition Options
(Section [3034]; options [1] & [2])
(Section [3034]: options [5] & [6])
[1]
OFF
[2]
OFF
- Disabled (default)
[5] [6]
OFF OFF - Disabled (default)
OFF
ON
- GENERATES TROUBLE ONLY (WHEN ARMED OR DISARMED)
OFF ON
ON
OFF
- When disarmed: GENERATES TROUBLE ONLY
- When armed: Follows Zone Alarm Types (page 7)
ON
OFF - When disarmed: GENERATES TROUBLE ONLY
- When armed: Follows Zone Alarm Types (page 7)
ON
ON
- When disarmed: GENERATES AUDIBLE ALARM
- When armed: Follows Zone Alarm Types (page 7)
ON
ON
- GENERATES TROUBLE ONLY (WHEN ARMED OR DISARMED)
- When disarmed: GENERATES AUDIBLE ALARM
- When armed: Follows Zone Alarm Types (page 7)
Dialer Options
= Default setting
SECTION [3036]: Dialer Options 1
SECTION [3037] : Dialer Options 2
OFF
Option
N See Table N See Table
N See Table N See Table
Telephone Line Monitoring (TLM) [1]&[2] (see table on page 29)
[3]
Dialer (reporting to monitoring
station)
[4]
Dialing method
[5]
[6]
Disabled NEnabled
N Pulse
Pulse ratio
(E.U. = Europe; N.A. = North America)
Busy tone detection
dialing on 5th
[7]
Switch to pulse
[8]
Bell/siren upon communication
failure if system is armed
ON
attempt
OFF
Option
Call back
Disabled
Automatic event buffer transmission
Disabled
N Enabled
Disabled
N Enabled
[3]&[4] Auto Test Report Transmission
Options (see table on page 29)
N See Table N See Table
N See Table N See Table
Tone (DTMF)
1:1.5 (N.A.)
[5]
N Disabled
Keypad beep on successful arming/
disarming report
Enabled
[6]
Alternate Dialing
[7]
Dial Tone Delay (if no dial tone)
Force dial
[8]
Report zone restore
Disabled
Disabled
N Enabled
N Enabled
ON = On zone closure; OFF = On bell cut-off
Digiplex DGP-NE96
- 30 -
N Enabled
[1]
[2]
N 1:2 (E.U.)
Disabled
ON
Programming Guide
Disabled N Enabled
N Hang-up
N Enabled
Telephone Line Monitoring (TLM) Options
Auto-Test Report Transmission Options
(Section [3036]; options [1] & [2])
(Section [3037]; options [3] & [4])
[1]
OFF
[2]
OFF
Disabled (default)
[3] [4]
OFF OFF Transmit the test report code every time the days programmed
in section [3040] have elapsed at the time programmed in
section [3041] (default).
OFF
ON
When armed: GENERATES AN AUDIBLE ALARM
ON
OFF
When armed: GENERATES A TROUBLE
ON
ON
TLM silent alarm: BECOMES AN AUDIBLE ALARM
OFF ON
When disarmed: Transmit test report code every time the
time programmed in section [3043] has elapsed.
When armed: Transmit test report code every time the time
programmed in section [3042] has elapsed.
ON
OFF The control panel will transmit the test report code every hour
on the minute value programmed in section [3041] (the last
two digits). Note that the first two digits of section [3041] will
be ignored. For example, if 10:25 was programmed into
section [3041], the test report code would be transmitted at
the 25th minute of every hour, i.e. 11:25, 12:25, etc.
ON
ON
The test report code will be transmitted when any of the
conditions of the second and third options listed above
(options [3] = OFF and [4] = ON / options [3] = ON and [4] =
OFF) are met.
Other Options
= Default setting
SECTION [3038]: Access Control Options
OFF
Option
ON
[1]
Access control feature
Disabled
N Enabled
[2]
Log “Request for Exit” in event
buffer*
Disabled
N Enabled
[3]
Log “Door Left Open Restore” in
event buffer
Disabled
N Enabled
[4]
Log “Door Forced Restore” in event
buffer
Disabled
N Enabled
[5]
Burglar alarm on forced door
Disabled
N Enabled
[6]
Skip exit delay when arming with
access card
[7]
Burglar alarm on door left open
Disabled
N Enabled
[8]
Who has access during clock loss
All users
* Since “Request for Exit” events can occur often, the Event
Buffer may fill up quickly.
Disabled N Enabled
N Masters
Schedule Tolerance Window
Section
[3039]
Data
Description
__/__/__ ( x 1 minute)
SCHEDULE TOLERANCE
Default
WINDOW
000
Auto Test Report Settings
Section
Data
Description
Default
[3040]
__/__/__ ( x 1 day; 000 = disabled)
AUTO TEST REPORT
000
[3041]
__/__ : __/__ Hrs (00-23) & Mins (00-59)
AUTO TEST REPORT TIME OF DAY
00 : 00
[3042]
__/__/__ (000 - 255 x 1 minute)
ARMED REPORT DELAY
5 minutes
[3043]
__/__/__ (000 - 255 x 1 minute)
DISARMED REPORT DELAY
60 minutes
Digiplex DGP-NE96
- 31 -
Programming Guide
Timings
Section
[3050]
Data
Description
Default
__/__/__ (001 - 125, 128 - 253; 000 = Disabled)
CLOCK COMPENSATION VALUE
Disabled
Adding Values: 001 to 125 = [value] x [.008] (+0.008 to 1 sec.)
Subtracting Values: 128 to 253 = [value] - [127] x [-.008] (-0.008 to -1.008 sec.)
[3051]
__/__/__ (000 - 255)
RING COUNTER
008
[3052]
__/__/__ (000 - 255 x 4 seconds)
ANSWERING MACHINE OVERRIDE DELAY
32 seconds
[3053]
__/__/__ (000 - 255 x 2 seconds)
TLM FAIL TIMER
32 seconds
[3054]
__/__/__ (000 - 127 x 1 second)
DELAY BETWEEN DIALING ATTEMPTS
20 seconds
[3055]
__/__/__ (000 - 255 x 1 second; 000 = Instant Report)
DELAY ALARM TRANSMISSION TIMER
000
[3056]
__/__/__ (000 - 255 x 1 attempt)
MAXIMUM DIALING ATTEMPTS
8 attempts
[3057]
__/__/__ (000 - 127 x 1 second)
PAGER DELAY BEFORE DATA TRANSMISSION
60 seconds
[3058]
__/__/__ (000 - 255 x 1 minute; 000 = Instant Report)
DELAY POWER FAILURE REPORT
30 minutes
[3059]
__/__/__ (000 - 255 x 1 repeat; 000 = No Repeat)
REPEAT PAGER REPORT CODE TRANSMISSION
000
Communication Settings
Account Numbers
Only the SIA format supports the [0] = 0 digit in its account numbers. Account numbers that use other reporting formats do not support
the [0] = 0 digit. Enter the [STAY] = A digit in its place. When using the SIA Format, and the Account Number Transmission (see option [6]
in section [3035] on page 30) corresponds to the partition, the control panel only uses the Partition 1 Account Number programmed in
section [3061], but the report code includes the partition number.
MSTN = Monitoring Station Telephone Number
Section
Data - Hex Value (0000 - FFFF)
Description
Default
1 †)
0000
[3061]
__/__/__/__ (if less than 4 digits, press [ENTER])
ACCOUNT NUMBER 1 (PARTITION 1* / MSTN
[3062]
__/__/__/__ (if less than 4 digits, press [ENTER])
ACCOUNT NUMBER 2 (PARTITION 2* / MSTN 2†)
0000
[3063]
__/__/__/__ (if less than 4 digits, press [ENTER])
ACCOUNT NUMBER 3 (PARTITION 3 */ MSTN 3†)
0000
[3064]
__/__/__/__ (if less than 4 digits, press [ENTER])
ACCOUNT NUMBER 4 (PARTITION 4 */ MSTN 4†)
0000
[3065]
__/__/__/__ (if less than 4 digits, press [ENTER])
ACCOUNT NUMBER 5 (PARTITION 5* / N/A†)
0000
[3066]
__/__/__/__ (if less than 4 digits, press [ENTER])
ACCOUNT NUMBER 6 (PARTITION 6* / N/A†)
0000
[3067]
__/__/__/__ (if less than 4 digits, press [ENTER])
ACCOUNT NUMBER 7 (PARTITION 7* / N/A†)
0000
[3068]
__/__/__/__ (if less than 4 digits, press [ENTER])
ACCOUNT NUMBER 8 (PARTITION 8* / N/A†)
0000
* Option [6] in section [3035] is disabled.
†
Option [6] in section [3035] is enabled.
Reporting Formats
Section
[3070]
Description
___
___
___
___
REPORTING FORMATS FOR TELEPHONE NUMBERS 1 TO 4
Use the same format for each number. Only the pager format can be used with
other reporting formats.
For more information, refer to Automatic Report Code Programming on
page 41.
Digiplex DGP-NE96
- 32 -
Programming Guide
Section Data (Press [ENTER] if less than 32 digits)
Description
[3071] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__MONITORING STATION/PAGER TELEPHONE #1
[3072] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__MONITORING STATION/PAGER TELEPHONE #2
[3073] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__MONITORING STATION/PAGER TELEPHONE #3
[3074] __/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__MONITORING STATION/PAGER TELEPHONE #4
For North American installations using either SIA or Contact ID reporting formats, enter *70 and then either P (4-second pause) or W (wait
for second dial tone) before the phone number in sections [3071] to [3074] to disable call-waiting.
Special Telephone Number Keys
Function
LCD
Grafica
Function
Clear
[#]
[FORCE]
Delete
[ARM] (press key until desired Delete from cursor to the end
[DISARM] letter/symbol appears) Insert space
[BYP]
[STAY]
*
#
Switch to Tone Dialing (T)
Wait for second dial tone (W)
4-second pause (P)
LCD
[CLEAR]
Grafica
Left action key (Clear)
[TRBL]
[ACC]
[MEM]
—
—
—
System Event Call Direction
= Default setting
SECTION [3080]: System Troubles & Trouble Restores
OFF
Option
[1]
Call Telephone #1
N Disabled
[2]
Call Telephone #2
Disabled
[3]
Call Telephone #3
Disabled
[4]
Call Telephone #4
Disabled
[5]
Backup on Telephone #1
Disabled
[6]
Backup on Telephone #2
Disabled
[7]
Backup on Telephone #3
Disabled
[8]
Backup on Telephone #4
Disabled
SECTION [3081]: Special Reporting
ON
Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
Digiplex DGP-NE96
OFF
Option
- 33 -
[1]
Call Telephone #1
N Disabled
[2]
Call Telephone #2
Disabled
[3]
Call Telephone #3
Disabled
[4]
Call Telephone #4
Disabled
[5]
Backup on Telephone #1
Disabled
[6]
Backup on Telephone #2
Disabled
[7]
Backup on Telephone #3
Disabled
[8]
Backup on Telephone #4
Disabled
Programming Guide
ON
Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
N Enabled
Partition Settings
Section
[3100]
[3200]
Partition Label
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Partition 1
Section
[3500]
Partition Label
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Partition 5
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Partition 2
[3600]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Partition 6
[3300]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Partition 3
[3700]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Partition 7
[3400]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Partition 4
[3800]
__/__/__/__/__/__/__/__/__/__/__/__/__/__/__/__ Partition 8
Auto-Arm Times
SECTION [3101]: Partition 1
SECTION [3201]: Partition 2
SECTION [3301]: Partition 3
SECTION [3401]: Partition 4
Hours (00-23) & Minutes (00-59)
Hours (00-23) & Minutes (00-59)
Hours (00-23) & Minutes (00-59)
Hours (00-23) & Minutes (00-59)
__/__ : __/__
__/__ : __/__
__/__ : __/__
__/__ : __/__
SECTION [3501]: Partition 5
SECTION [3601]: Partition 6
SECTION [3701]: Partition 7
SECTION [3801]: Partition 8
Hours (00-23) & Minutes (00-59)
Hours (00-23) & Minutes (00-59)
Hours (00-23) & Minutes (00-59)
Hours (00-23) & Minutes (00-59)
__/__ : __/__
__/__ : __/__
__/__ : __/__
__/__ : __/__
Arming Report Schedules (If partition is armed outside schedule, the panel will send an Early to Close [3916] and/or Late to Close [3917] report code; see page 39)
Section
Schedule
[3102]
Partition 1
001
[3202]
Partition 2
002
[3302]
Partition 3
003
[3402]
Partition 4
004
[3502]
Partition 5
005
[3602]
Partition 6
006
[3702]
Partition 7
007
[3802]
Partition 8
008
Intervals
Start Time (from)
End Time (to)
Days (turn ON or OFF)
S M T W
T
F S H
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Disarming Report Schedules (if partition is disarmed outside schedule, the panel will send an Early to Open [3926] and/or Late to Open [3927] report code; see page 39)
Section
Schedule
Intervals
Start Time (from)
___ ___ : ___ ___
End Time (to)
T
F S H
1
5
6
[3103]
Partition 1
001
Schedule A
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
[3203]
Partition 2
002
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
[3303]
Partition 3
003
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
[3403]
Partition 4
004
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
[3503]
Partition 5
005
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
[3603]
Partition 6
006
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
[3703]
Partition 7
007
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
[3803]
Partition 8
008
Schedule A
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Schedule B
___ ___ : ___ ___
___ ___ : ___ ___
1
2
3
4
5
6
7 8
Digiplex DGP-NE96
- 34 -
___ ___ : ___ ___
Days (turn ON or OFF)
S M T W
Programming Guide
2
3
4
7 8
Partition Timers
Description
Decimal Values from 000 to 255
Arming/Disarming Schedule Tolerance
Window (Data x 1 minute; Default = 000)
# of Invalid Codes Before Lockout
(Data x 1 attempt; Default = Disabled)
Keypad Lockout Duration
(Data x 1 minute; Default = Report Only)
No Movement Timer
(Data x 15 minutes; Default = Disabled)
Exit Delay Timer
(Data x 1 second; Default = 060 seconds)
Recent Closing Delay
(Data x 1 second; Default = Disabled)
Intellizone Delay
Digiplex DGP-NE96
(Data x 1 second; Default = 010 seconds)
Entry Delay 1
(Data x 1 second; Default = 030 seconds)
Entry Delay 2
(Data x 1 second; Default = 060 seconds)
Bell Cut-off Timer
(Data x 1 minute; Default = 4 minutes)
Auto Zone Shutdown
(000 to 015 zones; Default = Disabled)
Max. # of Zones that can be Bypassed
(Data x 1 zone; Default = unlimited)
- 35 -
Recycle Delay
(Data x 1 minute; Default = Disabled)
Number of Recycles
(Data x 1 attempt; Default = unlimited)
Programming Guide
Police Code Timer
(Data x 1 minute; Default = Disabled)
Closing Delinquency Timer
(Data x 1 day; Default = Disabled)
Partition 1
Partition 2
Partition 3
Partition 4
Partition 5
Partition 6
Partition 7
Partition 8
Section
Data
Section
Data
Section
Data
Section
Data
Section
Data
Section
Data
Section
Data
Section
Data
[3104]
__/__/__
[3204]
__/__/__
[3304]
__/__/__
[3404]
__/__/__
[3504]
__/__/__
[3604]
__/__/__
[3704]
__/__/__
[3804]
__/__/__
[3105]
__/__/__
[3205]
__/__/__
[3305]
__/__/__
[3405]
__/__/__
[3505]
__/__/__
[3605]
__/__/__
[3705]
__/__/__
[3805]
__/__/__
[3106]
__/__/__
[3206]
__/__/__
[3306]
__/__/__
[3406]
__/__/__
[3506]
__/__/__
[3606]
__/__/__
[3706]
__/__/__
[3806]
__/__/__
[3107]
__/__/__
[3207]
__/__/__
[3307]
__/__/__
[3407]
__/__/__
[3507]
__/__/__
[3607]
__/__/__
[3707]
__/__/__
[3807]
__/__/__
[3108]
__/__/__
[3208]
__/__/__
[3308]
__/__/__
[3408]
__/__/__
[3508]
__/__/__
[3608]
__/__/__
[3708]
__/__/__
[3808]
__/__/__
[3109]
__/__/__
[3209]
__/__/__
[3309]
__/__/__
[3409]
__/__/__
[3509]
__/__/__
[3609]
__/__/__
[3709]
__/__/__
[3809]
__/__/__
[3110]
__/__/__
[3210]
__/__/__
[3310]
__/__/__
[3410]
__/__/__
[3510]
__/__/__
[3610]
__/__/__
[3710]
__/__/__
[3810]
__/__/__
[3111]
__/__/__
[3211]
__/__/__
[3311]
__/__/__
[3411]
__/__/__
[3511]
__/__/__
[3611]
__/__/__
[3711]
__/__/__
[3811]
__/__/__
[3112]
__/__/__
[3212]
__/__/__
[3312]
__/__/__
[3412]
__/__/__
[3512]
__/__/__
[3612]
__/__/__
[3712]
__/__/__
[3812]
__/__/__
[3113]
__/__/__
[3213]
__/__/__
[3313]
__/__/__
[3413]
__/__/__
[3513]
__/__/__
[3613]
__/__/__
[3713]
__/__/__
[3813]
__/__/__
[3114]
__/__/__
[3214]
__/__/__
[3314]
__/__/__
[3414]
__/__/__
[3514]
__/__/__
[3614]
__/__/__
[3714]
__/__/__
[3814]
__/__/__
[3115]
__/__/__
[3215]
__/__/__
[3315]
__/__/__
[3415]
__/__/__
[3515]
__/__/__
[3615]
__/__/__
[3715]
__/__/__
[3815]
__/__/__
[3116]
__/__/__
[3216]
__/__/__
[3316]
__/__/__
[3416]
__/__/__
[3516]
__/__/__
[3616]
__/__/__
[3716]
__/__/__
[3816]
__/__/__
[3117]
__/__/__
[3217]
__/__/__
[3317]
__/__/__
[3417]
__/__/__
[3517]
__/__/__
[3617]
__/__/__
[3717]
__/__/__
[3817]
__/__/__
[3118]
__/__/__
[3218]
__/__/__
[3318]
__/__/__
[3418]
__/__/__
[3518]
__/__/__
[3618]
__/__/__
[3718]
__/__/__
[3818]
__/__/__
[3119]
__/__/__
[3219]
__/__/__
[3319]
__/__/__
[3419]
__/__/__
[3519]
__/__/__
[3619]
__/__/__
[3719]
__/__/__
[3819]
__/__/__
Partition Options 1
SECTION [3121] : Partition 1
Option
(
= Default Setting)
[1]
Switch to Stay Arm (if no Delay zone opened)
[2]
Arm/Disarm with Partition 2
[3]
Arm/Disarm with Partition 3
[4]
Arm/Disarm with Partition 4
[5]
Arm/Disarm with Partition 5
[6]
Arm/Disarm with Partition 6
[7]
Arm/Disarm with Partition 7
[8]
Arm/Disarm with Partition 8
SECTION [3221] : Partition 2
OFF
ON
Disabled
Enabled
N
N
N
N
N
N
N
N
Option
(
= Default Setting)
[1]
Arm/Disarm with Partition 1
[2]
Switch to Stay Arm (if no Delay zone opened)
[3]
Arm/Disarm with Partition 3
[4]
Arm/Disarm with Partition 4
[5]
Arm/Disarm with Partition 5
[6]
Arm/Disarm with Partition 6
[7]
Arm/Disarm with Partition 7
[8]
Arm/Disarm with Partition 8
SECTION [3321] : Partition 3
OFF
ON
Disabled
Enabled
N
N
N
N
N
N
N
N
Option
(
= Default Setting)
[1]
Arm/Disarm with Partition 1
[2]
Arm/Disarm with Partition 2
[3]
Switch to Stay Arm (if no Delay zone opened)
[4]
Arm/Disarm with Partition 4
[5]
Arm/Disarm with Partition 5
[6]
Arm/Disarm with Partition 6
[7]
Arm/Disarm with Partition 7
[8]
Arm/Disarm with Partition 8
OFF
ON
Disabled
Enabled
N
N
N
N
N
N
N
N
SECTION [3421] : Partition 4
Option
(
SECTION [3521] : Partition 5
= Default Setting)
[1]
Arm/Disarm with Partition 1
[2]
Arm/Disarm with Partition 2
[3]
Arm/Disarm with Partition 3
[4]
Switch to Stay Arm (if no Delay zone opened)
[5]
Arm/Disarm with Partition 5
[6]
Arm/Disarm with Partition 6
[7]
Arm/Disarm with Partition 7
[8]
Arm/Disarm with Partition 8
OFF
ON
Disabled
Enabled
N
N
N
N
N
N
N
N
Digiplex DGP-NE96
SECTION [3721] : Partition 7
Option
(
- 36 Programming Guide
Arm/Disarm with Partition 1
[2]
Arm/Disarm with Partition 2
[3]
Arm/Disarm with Partition 3
[4]
Arm/Disarm with Partition 4
[5]
Arm/Disarm with Partition 5
[6]
Arm/Disarm with Partition 6
[7]
Switch to Stay Arm (if no Delay zone opened)
[8]
Arm/Disarm with Partition 8
= Default Setting)
(
[1]
Arm/Disarm with Partition 1
[2]
Arm/Disarm with Partition 2
[3]
Arm/Disarm with Partition 3
[4]
Arm/Disarm with Partition 4
[5]
Switch to Stay Arm (if no Delay zone opened)
[6]
Arm/Disarm with Partition 6
[7]
Arm/Disarm with Partition 7
[8]
Arm/Disarm with Partition 8
ON
Disabled
Enabled
N
N
N
N
N
N
N
N
Option
= Default Setting)
(
[1]
Arm/Disarm with Partition 1
[2]
Arm/Disarm with Partition 2
[3]
Arm/Disarm with Partition 3
[4]
Arm/Disarm with Partition 4
[5]
Arm/Disarm with Partition 5
[6]
Switch to Stay Arm (if no Delay zone opened)
[7]
Arm/Disarm with Partition 7
[8]
Arm/Disarm with Partition 8
OFF
ON
Disabled
Enabled
N
N
N
N
N
N
N
N
SECTION [3821] : Partition 8
= Default Setting)
[1]
Option
SECTION [3621] : Partition 6
OFF
OFF
ON
Disabled
Enabled
Option
N
N
N
N
N
N
N
N
= Default Setting)
(
[1]
Arm/Disarm with Partition 1
[2]
Arm/Disarm with Partition 2
[3]
Arm/Disarm with Partition 3
[4]
Arm/Disarm with Partition 4
[5]
Arm/Disarm with Partition 5
[6]
Arm/Disarm with Partition 6
[7]
Arm/Disarm with Partition 7
[8]
Switch to Stay Arm (if no Delay zone opened)
OFF
ON
Disabled
Enabled
N
N
N
N
N
N
N
N
Partition Arming / Disarming Options
Partition 1
[3122]
Option
(
= Default Setting)
[1]
Timed Auto-Arming
[2]
“No Movement” Auto-Arming
[3]
Arming method for Auto Arm (OFF = Force Arming;
[4]
Exit Delay Termination
OFF
ON
N
Partition 2
[3222]
OFF
N
ON = Stay Arming)
[5]
Enable Arming Report Schedule
[6]
Enable Disarming Report Schedule
[7]
Future Use
[8]
Follow zone switches to Entry Delay 2 when delay zone is
bypassed
N
N
N
N
N/A
N
OFF
N
N
N
N/A
ON
Partition 3
[3322]
N
N
N
N/A
N
OFF
N
N
N
N/A
ON
Partition 4
[3422]
N
N
N
N/A
N
OFF
N
N
N
N/A
ON
Partition 5
[3522]
N
N
N
N/A
N
OFF
N
N
N
N/A
ON
Partition 6
[3622]
N
N
N
N/A
N
OFF
N
N
N
N/A
ON
Partition 7
[3722]
N
N
N
N/A
N
OFF
N
N
N
N/A
ON
Partition 8
[3822]
N
N
N
N/A
N
N
N
N
N/A
ON
N
N
N
N/A
N
N/A
Partition Panic Alarm Options
Partition 1
[3123]
Option
(
= Default Setting)
[1]
Panic 1 (Keys 1 & 3)
[2]
Panic 2 (Keys 4 & 6)
[3]
Panic 3 (Keys 7 & 9)
[4]
Panic 1 Alarm Type (OFF = Report Only;
ON = Audible Alarm)
OFF
ON
N
Partition 2
[3223]
OFF
N
[5]
Panic 2 Alarm Type (OFF = Report Only;
ON = Audible Alarm)
Panic 3 Alarm Type (OFF = Report Only;
ON = Fire Alarm)
[7]
Report Disarming Options (OFF = Always;
[8]
Always Force Arm when Regular Arming
N
N
N
N
N
N
N
N
N
N
N
N
N
ON
N
N
N
N
N
OFF
N
N
N
ON
Partition 8
[3823]
N
N
N
N
N
OFF
N
N
N
ON
Partition 7
[3723]
N
N
N
N
N
OFF
N
N
N
ON
Partition 6
[3623]
N
N
N
N
N
OFF
N
N
N
ON
Partition 5
[3523]
N
N
N
N
N
OFF
N
N
N
ON
Partition 4
[3423]
N
N
N
ON = Only After Alarm)
N
OFF
N
N
[6]
ON
Partition 3
[3323]
N
N
N
Digiplex DGP-NE96
Partition Bell Squawk Options
Partition 1
[3124]
Option
(
= Default Setting)
- 37 Programming Guide
[1]
Bell Squawk upon Disarming
[2]
Bell Squawk upon Arming
[3]
Bell Squawk upon Auto-arming
[4]
Bell Squawk during Exit Delay
[5]
Bell Squawk during Entry Delay
[6]
Bell Squawk upon Remote Arming/Disarming
[7]
Ring Back: Bell Squawk if Disarmed after Alarm
[8]
Ring Back: Keypad beeps if Disarmed after Alarm
OFF
ON
N
Partition 2
[3224]
OFF
N
N
N
OFF
N
N
N
N
OFF
N
N
N
N
OFF
N
N
N
N
OFF
N
N
N
N
OFF
N
N
N
N
OFF
N
N
N
N
N
N
N
ON
N
N
N
N
ON
Partition 8
[3824]
N
N
N
N
ON
Partition 7
[3724]
N
N
N
N
ON
Partition 6
[3624]
N
N
N
N
ON
Partition 5
[3524]
N
N
N
N
ON
Partition 4
[3424]
N
N
N
N
N
N
N
N
ON
Partition 3
[3324]
N
N
N
N
N
Partition One-Touch Options
Partition 1
[3125]
Option
(
[1]
One-touch Regular Arming*
[2]
One-touch Stay Arming*
[3]
One-touch Instant Arming*
[4]
One-touch Force Arming*
[5]
One-touch Stay or Instant Disarming*
[6]
One-touch Bypass Programming*
= Default Setting)
[7]
One-touch Event Display*
[8]
No Exit Delay when Arming with remote control
OFF
ON
N
Partition 2
[3225]
OFF
N
OFF
N
N
N
OFF
OFF
N
OFF
OFF
N
N
N
N
N
N
N
N
ON
N
N
N
N
N
N
N
N
ON
Partition 8
[3825]
N
N
N
N
N
N
N
N
ON
Partition 7
[3725]
N
N
N
N
N
N
N
N
ON
Partition 6
[3625]
N
N
N
N
ON
Partition 5
[3525]
N
N
N
N
OFF
N
N
N
N
N
N
N
ON
Partition 4
[3425]
N
N
N
N
N
N
N
N
ON
Partition 3
[3325]
N
N
N
* If a keypad is assigned to more than one partition, the one-touch feature must be enabled in all the keypad’s assigned partitions. Example: To enable the one-touch Regular Arming
feature of a keypad assigned to partitions 1, 2 and 5, enable sections [3125] option [1], [3225] option [1] and [3525] option [1].
Partition Arming / Disarming Event Call Direction
Partition 1
[3127]
Option
(
[1]
Call Telephone Number 1
[2]
Call Telephone Number 2
[3]
Call Telephone Number 3
[4]
Call Telephone Number 4
[5]
Backup on Telephone Number 1
[6]
Backup on Telephone Number 2
[7]
Backup on Telephone Number 3
[8]
Backup on Telephone Number 4
= Default Setting)
OFF
N
ON
N
Partition 2
[3227]
OFF
N
N
ON
N
Partition 3
[3327]
OFF
N
N
N
N
N
N
OFF
N
N
N
N
N
N
N
N
N
N
ON
N
N
N
N
N
OFF
N
N
N
ON
Partition 8
[3827]
N
N
N
N
N
OFF
N
N
N
ON
Partition 7
[3727]
N
N
N
N
ON
Partition 6
[3627]
N
N
N
N
N
OFF
N
N
N
ON
Partition 5
[3527]
N
N
N
N
N
N
N
N
N
OFF
N
N
N
ON
Partition 4
[3427]
N
N
N
Digiplex DGP-NE96
Partition Alarm / Alarm Restore Event Call Direction
Partition 1
[3128]
Option
(
- 38 -
[1]
Call Telephone Number 1
[2]
Call Telephone Number 2
[3]
Call Telephone Number 3
[4]
Call Telephone Number 4
Programming Guide
[5]
Backup on Telephone Number 1
[6]
Backup on Telephone Number 2
[7]
Backup on Telephone Number 3
[8]
Backup on Telephone Number 4
= Default Setting)
OFF
N
ON
N
Partition 2
[3228]
OFF
N
N
ON
N
Partition 3
[3328]
OFF
N
N
N
N
N
N
OFF
N
N
N
N
N
N
N
N
N
N
ON
N
N
N
N
N
OFF
N
N
N
ON
Partition 8
[3828]
N
N
N
N
N
OFF
N
N
N
ON
Partition 7
[3728]
N
N
N
N
ON
Partition 6
[3628]
N
N
N
N
N
OFF
N
N
N
ON
Partition 5
[3528]
N
N
N
N
N
N
N
N
N
OFF
N
N
N
ON
Partition 4
[3428]
N
N
N
Partition Tamper / Tamper Restore Event Call Direction
Partition 1
[3129]
Option
(
[1]
Call Telephone Number 1
[2]
Call Telephone Number 2
[3]
Call Telephone Number 3
[4]
Call Telephone Number 4
[5]
Backup on Telephone Number 1
[6]
Backup on Telephone Number 2
[7]
Backup on Telephone Number 3
[8]
Backup on Telephone Number 4
= Default Setting)
OFF
N
ON
N
N
N
N
N
N
N
Partition 2
[3229]
OFF
N
ON
N
N
N
N
N
N
N
Partition 3
[3329]
OFF
N
ON
N
N
N
N
N
N
N
Partition 4
[3429]
OFF
N
ON
N
N
N
N
N
N
N
Partition 5
[3529]
OFF
N
ON
N
N
N
N
N
N
N
Partition 6
[3629]
OFF
N
ON
N
N
N
N
N
N
N
Partition 7
[3729]
OFF
N
ON
N
N
N
N
N
N
N
Partition 8
[3829]
OFF
N
ON
N
N
N
N
N
N
N
Special and Trouble Report Codes
Ademco slow, Silent Knight fast, SESCOA, Ademco express or Pager formats: Key-in desired 2-digit hex values from 00 to FF.
Ademco format:
Use sections [4034] (Special System Report Codes), [4035] (Special Arming/Disarming Report Codes), [4036] (Special Alarm Report Codes) and [4037]
(Trouble/Trouble Restore Report Codes) to program a set of default Ademco report codes from the Automatic Report Code Programming on page 41. Then
to program the remaining report codes or to change some of the defaults, enter the individual sections and key-in the desired 2-digit hex value found in the
Contact ID Report Code List on page 44.
SIA format:
Use sections [4034] (Special System Report Codes), [4035] (Special Arming/Disarming Report Codes), [4036] (Special Alarm Report Codes) and [4037]
(Trouble/Trouble Restore Report Codes) to program a set of SIA report codes from the Automatic Report Code Programming on page 41. Codes that have
not been set to default can be set to default manually by entering FF in the appropriate section. To disable the reporting of an event, enter 00 in the
appropriate section.
Special System Report Codes
Section
Special Alarm Report Codes
Report Code
Section
Report Code
[3900]
__/__ Power up after total power down
[3930]
__/__ Emergency Panic
[3901]
__/__ Software reset (Watchdog)
[3931]
__/__ Auxiliary Panic
[3902]
__/__ Test Report
[3932]
__/__ Fire Panic
[3903]
Future Use
[3933]
__/__ Recent Closing
[3904]
__/__ WinLoad Login Request
[3934]
__/__ Police Code
[3905]
__/__ WinLoad Log Off
[3935]
__/__ Zone Shutdown
[3906]
__/__ Installer In
[3936]
__/__ Duress
[3907]
__/__ Installer Out
[3937]
__/__ Keypad Lockout
[3908]
Future Use
[3938]
Future Use
[3909]
Future Use
[3939]
Future Use
Special Arming Report Codes
Section
Trouble Report Codes
Report Code
Section
Report Code
[3910]
__/__ Auto-arming
[3940]
__/__ TLM1 Failure
[3911]
__/__ PC Arming
[3941]
__/__ AC Failure
[3912]
__/__ Late to Close (Auto-arming)
[3942]
__/__ Battery Failure
[3913]
__/__ No Movement
[3943]
__/__ Auxiliary Supply
[3914]
__/__ Partial Arming
[3944]
__/__ Bell Output (Disconnected or overload)
[3915]
__/__ Quick Arming
[3945]
__/__ Clock Loss
[3916]
__/__ Early to Close (refer to “Arming Report Schedules” on page 34)
[3946]
__/__ Fire Loop Trouble
[3917]
__/__ Late to Close (refer to “Arming Report Schedules” on page 34)
[3947]
Future Use
[3918]
__/__ Remote Arming (APR3-ADM2)
[3948]
Future Use
[3919]
__/__ Closing Delinquency
[3949]
Future Use
[3950]
__/__ Combus Fault
[3951]
__/__ Module Tamper
Report Code
[3952]
__/__ ROM Check Error
[3920]
__/__ Cancel Auto-arm
[3953]
__/__ Module TLM
[3921]
__/__ Quick Disarm
[3954]
__/__ Module Failure to Communicate
[3922]
__/__ PC Disarming
[3955]
__/__ Printer Fault
[3923]
__/__ PC Disarming after alarm
[3956]
__/__ Module AC Failure
[3924]
__/__ Cancel Alarm
[3957]
__/__ Module Battery Failure
[3925]
Future Use
[3958]
__/__ Module Auxiliary Failure
[3926]
__/__ Early to Open (refer to “Disarming Report Schedules” on page 34)
[3959]
Future Use
[3927]
__/__ Late to Open (refer to “Disarming Report Schedules” on page 34)
[3960]
__/__ Wireless Transmitter Battery Low
[3928]
__/__ Remote Disarming (APR3-ADM2)
[3961]
__/__ Wireless Transmitter Supervision Trouble
[3929]
Future Use
[3962]
Future Use
[3963]
Future Use
[3964]
Future Use
[3965]
__/__ Phone Number 1 Fail to Communicate
Special Disarming Report Codes
Section
Digiplex DGP-NE96
- 39 -
Programming Guide
[3966]
__/__ Phone Number 2 Fail to Communicate
[3978]
Future Use
[3967]
__/__ Phone Number 3 Fail to Communicate
[3979]
Future Use
[3968]
__/__ Phone Number 4 Fail to Communicate
[3980]
__/__ Combus Fault Restore
[3969]
Future Use
[3981]
__/__ Module Tamper Restore
[3982]
__/__ ROM Check Error Restore
[3983]
__/__ Module TLM Restore
Trouble Restore Report Codes
Section
Report Code
[3984]
__/__ Module Failure to Communicate Restore
[3970]
__/__ TLM1 Restore
[3985]
__/__ Printer Fault Restore
[3971]
__/__ AC Failure Restore
[3986]
__/__ Module AC Failure Restore
[3972]
__/__ Battery Failure Restore
[3987]
__/__ Module Battery Failure Restore
[3973]
__/__ Auxiliary Supply Restore
[3988]
__/__ Module Auxiliary Failure Restore
[3974]
__/__ Bell Output (Reconnected or Restored)
[3989]
Future Use
[3975]
__/__ Clock Loss Restore
[3990]
__/__ Wireless Transmitter Battery Low Restore
[3976]
__/__ Fire Loop Trouble Restore
[3991]
__/__ Wireless Transmitter Supervision Trouble Restore
[3977]
Future Use
Other Settings and Modes
Section
[4000]
Description
Display Serial Number of Control Panel and All Modules Connected to the combus:
After entering section [4000], the keypad will display the 8-digit serial number of the control panel.
For LCD Keypads: Use the [ ] and [ ] keys to scroll through the serial number of each module connected to the combus.
For Grafica Keypads: Press the center action key (Next) to scroll through the serial number of each module on the combus.
[4001]
Module Reset:
Reset a module’s programmed contents to default by entering its serial number.
[4002]
Locate/Unlocate Module:
Locate a specific module (e.g. detector, zone expander, etc.) connected to the combus by entering the module's serial number. The green
“LOCATE” LED on the module will begin to flash until the serial number is re-entered or the appropriate “tamper” or “unlocate” switch on the
module is pressed.
[4003]
Module Programming Mode:
Enter the serial number of the module you wish to program.
[4004]
Module Broadcast:
Copy the contents of all programming sections from one module to one or more modules of the same type. Enter the serial number of the
source module, followed by the serial numbers of the modules you wish to program. To begin transferring data, press [ACC] on LCD
keypads or the center action key (Start) on Grafica keypads.
Label Broadcast:
Copy user, door and partition labels from the control panel to all keypads and printer modules connected to the combus. To transmit the
labels, in section [4004], enter the control panel’s serial number. From the Destination screen, do not enter a serial number, but press
[ACC] on LCD keypads or the center action key (Start) on Grafica keypads.
PLEASE NOTE: The Module and Label Broadcast feature will only work when a module is broadcasting its data to a module or to
modules of the same type and model number. For example, an APR-PRT1 (Printer Module) cannot broadcast to an APR3-PRT1.
Likewise, a DGP module cannot broadcast to a DGP2 module.
[4005]
Remove Modules:
After entering the section, the control panel will scan all modules connected to the combus. If any missing modules are detected (i.e.
detector removed from the combus), the control panel will erase the module's serial number, removing the module from the control panel's
memory.
Paradox Memory Card (PMC-3)
[4010]
Download from the Memory Key to the control panel except sections [0001] to [0096] and [0501] to [0532].
[4011]
Download from the Memory Key to control panel including sections [0001] to [0096] and [0501] to [0532].
[4020]
Copy the control panel sections to the Memory Key except sections [0001] to [0096] and [0501] to [0532].
[4021]
Copy the control panel sections to the Memory Key including sections [0001] to [0096] and [0501] to [0532].
Digiplex DGP-NE96
- 40 -
Programming Guide
Download Memory Key to Control Panel.
1)
2)
3)
Insert the Memory Key (PMC-3) onto the control panel’s connector labelled “MEM KEY”.
To download the contents of the Memory Key except sections [0001] to [0096] and [0501] to [0532], enter installer programming
mode and then enter section [4010].
To download the contents of the Memory Key including sections [0001] to [0096] and [0501] to [0532], enter installer programming
mode and then enter section [4011].
When the keypad emits a confirmation beep, remove the Memory Key.
Copy Control Panel to Memory Key
1)
2)
3)
Insert Memory Key (PMC-3) onto the control panel’s connector labelled “MEM KEY”. Ensure the write protect jumper on the memory
key is on.
To copy the contents to the Memory Key except sections [0001] to [0096] and [0501] to [0532], enter installer programming mode,
then enter section [4020].
To copy the contents to the Memory Key including sections [0001] to [0096] and [0501] to [0532], enter section [4021].
After the confirmation beep, remove the Memory Key. Remove the Memory Key’s jumper if you do not wish to accidentally overwrite
its contents.
Automatic Report Code Programming
When using Contact ID or SIA Reporting formats (section [3070] on page 32), default report codes can be programmed automatically. After automatic
defaults are set, they can be changed and the remaining report codes can be set manually.
Section
[4030]
Description
ALL REPORT CODES RESET TO 00
Resets all the report codes from sections [0201] to [0296], [0701] to [0832],
[2001] to [2199] and [3900] to [3999] to 00.
Sections [4031] to [4037] reset all the report codes in the following sections to
the default values from the “Automatic Report Codes List” on page 42:
[4031]
ALL REPORT CODES RESET TO FF
[0201] to [0296], [0701] to [0832], [2001] to [2199] & [3900] to [3999]
[4032]
ZONE ALARM/ALARM RESTORE AND ZONE TAMPER/TAMPER [0201] to [0296]
RESTORE REPORT CODES
[4033]
USER/KEYSWITCH ARMING & DISARMING REPORT CODES [0701] to [0832], and [2001] to [2199]
[4034]
SPECIAL CODES
[3900] to [3909]
[4035]
SPECIAL ARMING/DISARMING REPORT CODES
[3910] to [3929]
[4036]
SPECIAL ALARM REPORT CODES
[3930] to [3939]
[4037]
TROUBLE & TROUBLE RESTORE REPORT CODES
[3940] to [3999]
Software Reset
Performing a software reset will set certain parameters to default values. To do so:
1) Make sure the “RESET” jumper (see page 49) on the control panel is ON.
2) Enter Programming Mode (see page 1).
3) Enter the 4-digit [SECTION] corresponding to the software reset you wish to perform:
Section
Description
[4040]
Entering this section will reset all programmable sections from [0001] to [3999] to factory default values.
[4041]
Entering this section will reset the system master code to 123456.
[4042]
Entering this section will reset all Zone (sections [0001] to [0196], [0201] to [0296], and sections [0961] to [0984]) programming to default
values.
[4043]
Entering this section will reset all access control sections from [2201] to [2712], excluding door labels, to default values.
[4044]
Entering this section will reset all user code sections from [1001] to [1999] and [2001] to [2199] to default values.
[4045]
Entering this section will reset all dialer (sections [3051] to [3081]) and control panel (sections [3020] to [3043], and [3900] to [3991])
programming to default values.
[4046]
Entering this section will reset all partition sections from [3101] to [3829], excluding partition labels, to default values.
[4047]
Entering this section will reset all PGM (sections from [0901] to [0939]) and all Keyswitch (sections [0501] to [0632]) programming, as well
as all Keyswitch arming/disarming report codes (sections from [0701] to [0832]) to default values.
[4048]
Entering this section will clear all user labels, door labels, partition labels, and zone labels from sections [0301] to [0396].
Digiplex DGP-NE96
- 41 -
Programming Guide
Installer Quick Function Keys
Press and hold the [0] key and then enter the [INSTALLER CODE]. Then press one of the following function keys:
[STAY]
Test Report: Sends the “Test Report” report code programmed in section [3902] to the monitoring station.
[FORCE]
Call WinLoad Software: Will dial the PC telephone number programmed in section [3010] in order to initiate communication with a computer
using the WinLoad software.
[ARM]
Answer WinLoad Software: Will force the control panel to answer a call made by the Monitoring Station that is using the WinLoad software.
[DISARM]
Cancel Communication: Cancels all communication with the WinLoad software or with the Monitoring Station until the next reportable event.
[MEM]
Installer Test Mode: The installer test mode will allow you to perform walk tests where the bell or siren will squawk to indicate opened zones.
Press the [MEM] button again to exit. Partitions cannot be armed if the Installer Test Mode is enabled.
[TRBL]
Start Module Scan: The keypad will display the serial number of each module on the combus.
[ACC]
Combus Voltmeter: To verify if the combus is supplying sufficient power, press and hold the [0] key, enter the [INSTALLER CODE] and press the
[ACC] button. A reading of 12.3V or lower indicates that the voltage is too low. The voltage may drop during the control panel battery test.
Automatic Report Code List
Default Contact ID Report Code
when using sections [4032] to [4037]
Default SIA Report Code
when using sections [4032] to [4037]
Arming with Master Code (##)
3 4A1 - Close by user
CL - Closing Report
Arming with User Code (##)
3 4A1 - Close by user
CL - Closing Report
Arming with Keyswitch (##)
3 4A9 - Keyswitch Close
CS - Closing Keyswitch
Auto Arming
3 4A3 - Automatic Close
CA - Automatic Closing
Arm with PC software
3 4A7 - Remote arm/disarm
CQ - Remote Arming
Late To Close
1 4A4 - Late to Close
OT - Late to Close
No Movement
1 4A4 - Late to Close
NA - No Activity
Partial arming
1 456 - Partial Arm
CG - Close Area
Quick arming
3 408 - Quick arm
CL - Closing Report
Disarm with Master Code (##)
1 4A1 - Open by user
OP - Opening Report
Disarm with User Code (##)
1 4A1 - Open by user
OP - Opening Report
Disarm with Keyswitch (##)
1 4A9 - Keyswitch Open
OS - Opening Keyswitch
Disarm after alarm with Master Code (##)
1 4A1 - Open by user
OP - Opening Report
Disarm after alarm with User Code (##)
1 4A1 - Open by user
OP - Opening Report
Disarm after alarm with Keyswitch (##)
1 4A1 - Keyswitch Open
OS - Opening Keyswitch
Cancel alarm with Master Code (##)
1 4A6 - Open by user
OR - Disarm From Alarm
Cancel alarm with User Code (##)
1 4A6 - Open by user
OR - Disarm From Alarm
Cancel alarm with Keyswitch (##)
1 4A6 - Keyswitch Open
OS - Opening Keyswitch
System Event
Auto Arming Cancellation
1 464 - Auto-Arm Time Extended
CE - Closing Extend
Disarm with PC software
1 4A7 - Remote arm/disarm
OQ - Remote Disarming
Disarm after an alarm with PC software
1 4A7 - Remote arm/disarm
OR - Disarm From Alarm
Quick Disarm
1 408 - Quick Disarm
OP - Opening Report
Zone Bypassed (##)
1 57A - Zone bypass
UB - Untyped Zone Bypass
Zone alarm (##)
1 13A - Burglary Alarm
BA - Burglary Alarm
Fire alarm (##)
1 11A - Fire alarm
FA - Fire Alarm
Zone alarm restore (##)
3 13A - Burglary Alarm Restore
BH - Burglary Alarm Restore
Fire alarm restore (##)
3 11A - Fire alarm Restore
FH - Fire Alarm Restore
24Hr Gas alarm (##)
1 13A - Burglary Alarm
GA - Gas Alarm
24Hr Heat alarm (##)
1 13A - Burglary Alarm
KA - Heat Alarm
24Hr Water alarm (##)
1 13A - Burglary Alarm
WA - Water Alarm
24Hr Freeze alarm (##)
1 13A - Burglary Alarm
ZA - Freeze Alarm
24Hr Gas alarm restore (##)
3 13A - Burglary Alarm Restore
GR - Gas Alarm Restore
24Hr Heat alarm restore (##)
3 13A - Burglary Alarm Restore
KR - Heat Alarm Restore
24Hr Water alarm restore (##)
3 13A - Burglary Alarm Restore
WR - Water Alarm Restore
24Hr Freeze alarm restore (##)
3 13A - Burglary Alarm Restore
ZR - Freeze Alarm Restore
Police Code
1 139 - Burglary Alarm
BM - Burglary Alarm
Panic 1 - Emergency
1 12A - Panic alarm
PA - Panic Alarm
Panic 2 - Medical
1 1AA - Medical alarm
MA - Medical Alarm
Panic 3 - Fire
1 115 - Pull Station
FA - Fire Alarm
Digiplex DGP-NE96
- 42 -
Programming Guide
System Event
Default Contact ID Report Code
when using sections [4032] to [4037]
Default SIA Report Code
when using sections [4032] to [4037]
Recent closing
3 4AA - Open/Close
CR - Recent Closing
Global zone shutdown
1 574 - Group bypass
CG - Close Area
Duress alarm
1 121 - Duress
HA - Hold-up Alarm
Zone shutdown (##)
1 57A - Zone bypass
UB - Untyped Zone Bypass
Zone tampered (##)
1 144 - Sensor tamper
TA - Tamper Alarm
Zone tamper restore (##)
3 144 - Sensor tamper restore
TR - Tamper Restoral
Keypad Lockout
1 421 - Access denied
JA - User Code Tamper
AC Failure
1 3A1 - AC loss
AT - AC Trouble
Battery Failure
1 3A9 - Battery test failure
YT - System Battery Trouble
Auxiliary supply trouble
1 3AA - System trouble
YP - Power Supply Trouble
Bell output current limit
1 321 - Bell 1
YA - Bell Fault
Bell absent
1 321 - Bell 1
YA - Bell Fault
Clock lost
1 626 - Time/Date inaccurate
JT - Time Changed
Fire loop trouble
1 373 - Fire trouble
FT - Fire Trouble
TLM trouble restore
3 351 - Telco 1 fault restore
LR - Phone Line restoral
AC Failure restore
3 3A1 - AC loss restore
AR - AC Restoral
Battery Failure restore
3 3A9 - Battery test restore
YR - System Battery Restoral
Auxiliary supply trouble restore
3 3AA - System trouble restore
YQ - Power Supply restored
Bell output current limit restore
3 321 - Bell 1 restore
YH - Bell Restored
Bell absent restore
3 321 - Bell 1 restore
YH - Bell Restored
Clock programmed
3 625 - Time/Date Reset
JT - Time Changed
Fire loop trouble restore
3 373 - Fire trouble restore
FJ - Fire Trouble Restore
Combus fault
1 333 - Expansion module failure
ET - Expansion Trouble
Module tamper
1 145 - Expansion module tamper
TA - Tamper Alarm
Module ROM_RAM_error
1 3A4 - Rom checksum bad
YF - Parameter Checksum Fail
Module TLM trouble
1 352 - Telco 2 fault
LT - Phone Line trouble
Module fail to communicate to monitoring station
1 354 - Fail to communicate
YC - Communication Fails
Printer fault
1 336 - Local printer failure
VT - Printer Trouble
Module AC Failure
1 3A1 - AC loss
AT - AC Trouble
Module battery failure
1 3A9 - Battery test failure
YT - System Battery Trouble
Module Auxiliary supply trouble
1 3AA - System trouble
YP - Power Supply Trouble
Combus fault restore
3 333 - Expansion module failure restore
ER - Expansion Restoral
Module tamper restore
3 145 - Expansion module tamper restore
TR - Tamper Restoral
Module ROM_RAM_error restore
3 3A4 - Rom checksum bad restore
YG - Parameter Changed
Module TLM restore
3 352 - Telco 2 fault restore
LR - Phone Line Restoral
Printer fault restore
3 336 - Local printer failure restore
VR - Printer Restore
Module AC restore
3 3A1 - AC loss restore
AR - AC Restoral
Module battery restore
3 3A9 - Battery test failure restore
YR - System Battery Restoral
Module Auxiliary supply restore
3 3AA - System trouble restore
YQ - Power Supply Restored
Fail to communicate with monitoring station
1 354 - Fail to communicate
YC - Communication Fails
Module RF low battery
1 384 - RF transmitter low battery
XT - Transmitter Battery Trouble
Module RF battery restore
3 384 - RF transmitter battery restore
XR - Transmitter Battery Restoral
Module RF supervision trouble
1 381 - Loss of supervision - RF
US - Untype Zone Supervision
Module RF supervision restore
3 381 - Supervision restore - RF
UR - Untyped Zone Restoral
Cold Start
1 3A8 - System shutdown
RR - Power Up
Warm Start
1 3A5 - System reset
YW - Watchdog Reset
Test Report engaged
1 6A2 - Periodic test report
TX - Test Report
PC software communication finished
1 412 - Successful - download access
RS - Remote Program Success
Installer on site
1 627 - Program mode Entry
LB - Local Program
Installer programming finished
1 628 - Program mode Exit
LS - Local Program Success
WinLoad Login request
1 411 - Call Back Request
RB - Remote Program Begin
Digiplex DGP-NE96
- 43 -
Programming Guide
Contact ID Report Code List
If using the Ademco Contact ID format, key in the 2-digit hexadecimal value (PROG. VALUE) to program the desired report codes into sections [0201] to
[0296], [0701] to [0832], [2001] to [2199], and [3900] to [3999].
CID#
Reporting Code
MEDICAL ALARMS - 100
100
Medical Alarm
101
Personal Emergency
102
Fail to Report In
FIRE ALARMS - 110
110
Fire Alarm
111
Smoke
112
Combustion
113
Water Flow
114
Heat
115
Pull Station
116
Duct
117
Flame
118
Near Alarm
PANIC ALARMS - 120
120
Panic Alarm
121
Duress
122
Silent
123
Audible
BURGLAR ALARMS - 130
130
Burglary
131
Perimeter
132
Interior
133
24-Hour
134
Entry/Exit
135
Day/Night
136
Outdoor
137
Tamper
138
Near Alarm
139
Intrusion Verifier
GENERAL ALARMS - 140
140
General Alarm
141
Polling Loop Open
142
Polling Loop Short
143
Expansion Module Failure
144
Sensor Tamper
145
Expansion Module Tamper
24-HOUR NON-BURGLARY - 150 & 160
150
24-Hour Non-Burglary
151
Gas Detected
152
Refrigeration
153
Loss of Heat
154
Water Leakage
155
Foil Break
156
Day Trouble
157
Low Bottled Gas Level
158
High Temperature
159
Low Temperature
161
Loss of Air Flow
FIRE SUPERVISORY - 200 & 210
200
Fire Supervisory
201
Low Water Pressure
202
Low CO2
203
Gate Valve Sensor
204
Low Water Level
205
Pump Activated
206
Pump Failure
SYSTEM TROUBLES - 300 & 310
300
System Trouble
301
AC Loss
Prog.
Value
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
Prog.
Prog.
CID#
Reporting Code
Value
Value
302
Low System Battery
35
ACCESS CONTROL - 420
303
RAM Checksum Bad
36
421
Access Denied
6A
304
ROM Checksum Bad
37
422
Access Report By User
6B
305
System Reset
38
SPECIAL TROUBLES - 450 & 460
306
Panel Program Changed
39
450
Exception Open/Close
6C
307
Self-Test Failure
3A
451
Early Open/Close
6D
308
System Shutdown
3B
452
Late Open/Close
6E
309
Battery Test Failure
3C
453
Failed to Open
6F
310
Ground Fault
3D
454
Failed to Close
70
SOUNDER/RELAY TROUBLES - 320
455
Auto-Arm Failed
71
320
Sounder Relay
3E
456
Partial Arm
72
321
Bell 1
3F
457
User Exit Error
73
322
Bell 2
40
458
User on Premises
74
323
Alarm Relay
41
459
Recent Close
75
324
Trouble Relay
42
461
Wrong Code Entry
76
325
Reversing Relay
43
462
Legal Code Entry
77
SYSTEM PERIPHERAL TROUBLES - 330 & 340
463
Re-arm after Alarm
78
330
System Peripheral
44
464
Auto-Arm Time Extended
79
331
Polling Loop Open
45
465
Panic Alarm Reset
7A
332
Polling Loop Short
46
466
Service On/Off Premises
7B
333
Expansion Module Failure
47
SOUNDER RELAY DISABLES - 520
334
Repeater Failure
48
520
Sounder/Relay Disabled
7C
335
Local Printer Paper Out
49
521
Bell 1 Disable
7D
336
Local Printer Failure
4A
522
Bell 2 Disable
7E
COMMUNICATION TROUBLES - 350 & 360
523
Alarm Relay Disable
7F
350
Communication
4B
524
Trouble Relay Disable
80
351
Telco Fault 1
4C
525
Reversing Relay Disable
81
352
Telco Fault 2
4D
COMMUNICATION DISABLES - 550 & 560
353
Long Range Radio
4E
551
Dialer Disabled
82
354
Fail to Communicate
4F
552
Radio Transmitter Disabled
83
355
Loss of Radio Supervision
50
BYPASSES - 570
356
Loss of Central Polling
51
570
Zone Bypass
84
PROTECTION LOOP TROUBLES - 370
571
Fire Bypass
85
370
Protection Loop
52
572
24-Hour Zone Bypass
86
371
Protection Loop Open
53
573
Burg. Bypass
87
372
Protection Loop short
54
574
Group Bypass
88
373
Fire Trouble
55
TEST/MISC. - 600
SENSOR TROUBLES - 380
601
Manual Trigger Test
89
380
Sensor Trouble
56
602
Periodic Test Report
8A
381
Loss of Supervision - RF
57
603
Periodic RF Transmission
8B
382
Loss of Supervision - RPM
58
604
Fire Test
8C
383
Sensor Tamper
59
605
Status Report to Follow
8D
384
RF Transmitter Low Battery
5A
606
Listen-in to Follow
8E
OPEN/CLOSE - 400
607
Walk Test Mode
8F
400
Open/Close
5B
621
Event Log Reset
90
401
Open/Close by User
5C
622
Event Log 50% Full
91
402
Group Open/Close
5D
623
Event Log 90% Full
92
403
Automatic Open/Close
5E
624
Event Log Overflow
93
404
Late to Open/Close
5F
625
Time/Date Reset
94
405
Deferred Open/Close
60
626
Time/Date Inaccurate
95
406
Cancel
61
627
Program Mode Entry
96
407
Remote Arm/Disarm
62
628
Program Mode Exit
97
408
Quick Arm
63
631
Exception Schedule Change
98
409
Keyswitch Open/Close
64
REMOTE ACCESS - 410
411
Callback Request Made
65
412
Success - Download Access
66
413
Unsuccessful Access
67
414
System Shutdown
68
415
Dialer Shutdown
69
CID#
Digiplex DGP-NE96
Reporting Code
- 44 -
Programming Guide
Control Panel Hardware Connections
Single Zone Inputs
ATZ - Double Zone Inputs
Digiplex DGP-NE96
- 45 -
Programming Guide
Connections
As indicated in Table 2 on page 48,
this run of wire can support 700PU.
Total PU on this run of wire:
(A) 40PU + (B) 28PU =
68PU<700PU = OK
As indicated in Table 2 on
page 48, this run of wire can
support 454PU. Total PU on this
run of wire:
(D) 80PU + (E) 30PU + (F) 80PU +
(G) 80PU = 270PU<454PU = OK
As indicated in Table 2 on page 48, this run of wire
can support 136PU. Total PU on this run of wire:
(A) 40PU + (C) 30PU = 70PU<136PU = OK
Digiplex DGP-NE96
- 46 -
Programming Guide
Telephone Line Connections
For TBR-21 compliance, please note the following:
1) The DGP-NE96 can be connected to the telephone network via an RJ-11 connector.
2) The Maximum Dialing Attempts cannot exceed 15 attempts (section [3056] on page 32).
Digiplex DGP-NE96
- 47 -
Programming Guide
Power Unit Consumption Table
Table 1: Power Unit Consumption Table
Description
QTY.
PU used by each
Total PU
Grafica Graphic LCD Keypad (DNE-K07):
_______
X
150PU =
__________ PU
LCD Keypad (DGP2-641):
_______
X
80PU =
__________ PU
LED Keypad (DGP2-648):
_______
X
115PU =
__________ PU
Addressable Detectors (DG85, DGP2-50/60/70):
_______
X
30PU =
__________ PU
Addressable Door Contact (DGP2-ZC1):
_______
X
30PU =
__________ PU
1-Zone Hardwire Expansion Module (DGP2-ZX1):
_______
X
14PU =
__________ PU
4-Zone Hardwire Module (APR3-ZX4):
_______
X
28PU =
__________ PU
8-Zone Hardwire Module (APR3-ZX8):
_______
X
28PU =
__________ PU
Wireless Module (OMN-RCV3):
_______
X
50PU =
__________ PU
1-PGM Output Module (APR3-PGM1):
_______
X
28PU =
__________ PU
4-PGM Output Module (APR3-PGM4):
_______
X
150PU =
__________ PU
Printer Module (APR3-PRT1):
_______
X
40PU =
__________ PU
DVACS Module (DGP2-DVAC):
_______
X
40PU =
__________ PU
Annunciator Module (DGP2-ANC1):
_______
X
105PU =
__________ PU
InTouch Voice-Assisted Arm/Disarm Module (APR3-ADM2):
_______
X
105PU =
__________ PU
Access Control Module (DGP2-ACM1P):
Note: The DGP2-ACM1P consumes 165PU from its own power supply.
_______
X
165PU =
__________ PU
Maximum available power units = 700PU
GRAND TOTAL
__________ PU
STEP 1:
Using Table 1, calculate the total number of power units (PU) required by each device, module, and accessory in the system. Please take into
account devices connected to the control panel’s PGM outputs. Since the BELL output has its own power supply, do not include the sirens
connected to it in the calculation.
STEP 2:
If the Grand Total is less than 700PU, go to step 3. If the value is greater, you will require an external power supply (see External Power Supply
Connections drawing on page 46) to provide the additional power needed. Proceed with step 3 and refer to the example (Sample Power
Requirement Calculations drawing) on page 46.
STEP 3:
Due to the degradation of a power signal over long distances (if this were the case, we recommend connecting a Paradox Power Supply
Module, DGP2-PS17), EACH length or run of wire in the system can support only a specific number of power units (PU). Using Table 2,
determine how many power units each length of wire can support. Please note that the total number of power units (PU) can never surpass
700PU.
Table 2: Power Unit (PU) Limitations For Each Run of Wire
Gauge: 18AWG, Surface: 0.823mm2
Length of each
run of wire
Gauge: 22AWG, Surface: 0.326mm2
Available Power
Units (PU)
Length of each
run of wire
Available Power
Units (PU)
Gauge: 24AWG, Surface: 0.205mm2
Length of each
run of wire
Available Power
Units (PU)
100ft. (30m)
700
100ft. (30m)
700
100ft. (30m)
700
200ft. (61m)
700
200ft. (61m)
682
200ft. (61m)
429
300ft. (91m)
700
300ft. (91m)
454
300ft. (91m)
286
400ft. (122m)
700
400ft. (122m)
341
400ft. (122m)
214
500ft. (152m)
690
500ft. (152m)
273
500ft. (152m)
171
600ft. (183m)
575
600ft. (183m)
227
600ft. (183m)
143
700ft. (213m)
493
700ft. (213m)
195
800ft. (244m)
431
800ft. (244m)
170
900ft. (274m)
383
900ft. (274m)
151
1000ft. (305m)
345
1000ft. (305m)
136
1500ft. (457m)
230
2000ft. (610m)
172
2500ft. (762m)
138
3000ft. (914m)
115
Digiplex DGP-NE96
- 48 -
Programming Guide
PCB Layout
PLEASE NOTE: It is strongly recommended that you test
your system on a weekly basis, and have your system
checked by a qualified technician a minimum of every 3 years.
When installing the combus wires in a noisy environment, or
when connecting the combus across separate buildings, you
must use a shielded cable. Refer to Connecting the Combus in
Noisy Environments on page 50.
PLEASE NOTE:
When powering up the DGP-NE96 control panel (V1.02 or higher), the panel will begin a module
scan to verify if all the modules connected to the panel are operational. The scanning process will
take between 30 and 120 seconds to complete depending on the number of modules connected
to the control panel. The module scan is complete when the LCD keypad begins to show the
partition status. Only after the module scan is complete will the control panel be fully operational.
Digiplex DGP-NE96
Refer to the UL and ULC Warnings section of the Digiplex DGP-NE96 Reference &
Installation Manual for UL and ULC warnings.
- 49 -
Programming Guide
Connecting the Combus in Noisy Environments
When installing the combus wires in proximity to high electrical interference such as neon lights, motors, high-voltage wiring, transformers, or if connecting
the combus across separate buildings, you must use shielded cables. Connect the shielded cable as detailed below:
Within the Same Building: Strip the outer jacket at one end of the shielded cable to expose the shield and connect the shield to the control panel ground
(not the dialer ground), while leaving the shield at the other end of the cable open (floating).
Across Separate Buildings: Strip the outer jacket at one end of the shielded cable to expose the shield. In the same building that houses the control panel,
connect the exposed shield to a cold water pipe or any other earth ground available, while leaving the shield at the other end of the cable open (floating). The
same configuration applies to any subsequent building.
Built-in RTC
Digiplex DGP-NE96 incorporates an RTC directly on the PC board. The RTC will save the control panel’s internal clock when both the AC and battery power
have been lost. After power is lost and then restored, the control panel will verify with and then retrieve the time from the RTC. The control panel will verify
and compare its time with the time stored in the RTC every hour. If the times are different, the control panel will reset its internal clock to the time saved in the
RTC. The RTC uses a 3V lithium battery (CR2032) with a battery life of 11 years. Change the battery as shown below:
Reprogram the control panel’s clock after changing the battery.
Danger of explosion exists if the lithium battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
Warranty
Paradox Security Systems Ltd. (“Seller”) warrants its products to be free from defects in materials and workmanship under normal use for a period of one
year. Except as specifically stated herein, all express or implied warranties whatsoever, statutory or otherwise, including without limitation, any implied
warranty of merchantability and fitness for a particular purpose, are expressly excluded. Because Seller does not install or connect the products and
because the products may be used in conjunction with products not manufactured by Seller, Seller cannot guarantee the performance of the security system
and shall not be responsible for circumstances resulting from the product’s inability to operate. Seller obligation and liability under this warranty is expressly
limited to repairing or replacing, at Seller's option, any product not meeting the specifications. Returns must include proof of purchase and be within the
warranty period. In no event shall the Seller be liable to the buyer or any other person for any loss or damages whether direct or indirect or consequential or
incidental, including without limitation, any damages for lost profits stolen goods, or claims by any other party, caused by defective goods or otherwise arising
from the improper, incorrect or otherwise faulty installation or use of the merchandise sold.
Notwithstanding the preceding paragraph, the Seller’s maximum liability will be strictly limited to the purchase price of the defective product. Your use of this
product signifies your acceptance of this warranty.
BEWARE: Dealers, installers and/or others selling the product are not authorized to modify this warranty or make additional warranties that are binding on
the Seller.
© 2002-2004 Paradox Security Systems Ltd. All rights reserved. Specifications may change without prior notice. One or more of the following US patents
may apply: 6215399, 6111256, 5751803, 5721542, 5287111, 5119069, 5077549, 5920259 and 5886632. Canadian and international patents may also apply.
Digiplex, Magellan, PosiPIN and WinLoad are trademarks or registered trademarks of Paradox Security Systems Ltd. or its affiliates in Canada, the United
States and/or other countries.
Digiplex DGP-NE96
- 50 -
Programming Guide
Notes
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
__________________________________________________________________________________
Digiplex DGP-NE96
- 51 -
Programming Guide
Trouble Display
To view the Trouble Display on LCD or LED keypads:
1) Press the [TRBL] key.
2) For LEDs: Press the Numerical Symbol corresponding to the Group heading to view the specific trouble.
For LCDs: Press the number representing the trouble and use the [ ] and [ ] keys to view the specific trouble.
To view the Trouble Display on Grafica Keypads:
1) Enter your [ACCESS CODE].
2) Using the scroll keys, highlight Trouble and then press the center action key (Ok). The trouble(s) will appear by Trouble Group.
3) If more than one Trouble Group appears, highlight the desired group before pressing the center action key (View) to view the specific trouble.
TROUBLE GROUP [1]: SYSTEM
[1] AC Failure
[2] Battery Trouble
[3] Aux. Current Limit
TROUBLE GROUP [2]: COMMUNICATOR
[4] Bell Current Limit
[5] Bell Absent
[6] ROM Check Error
[7] RAM Check Error
[1] TLM1
[2] Fail to Com. 1
[3] Fail to Com. 2
[4] Fail to Com. 3
[5] Fail to Com. 4
[6] Fail to Com. PC
TROUBLE GROUP [3]: MODULE TROUBLE
TROUBLE GROUP [4]: NETWORK (COMBUS) TROUBLES
[1] Module Tamper
[2] Module ROM Check
Error
[3] Module TLM Trouble
[4] Module Fail to Com.
[1] Missing Keypad
[2] Missing Module
[5] Printer Trouble
[6] Module AC Failure
[6] General Failure
[7] Combus Overload
[7] Module Battery Failure
[8] Module Supply Output
TROUBLE GROUP [5]: ZONE TAMPER
TROUBLE GROUP [6]: ZONE LOW BATTERY
Press the [5] button to display the tampered zone or zones.
Press the [6] button to display the zone(s) assigned to wireless devices with
low batteries.
TROUBLE GROUP [7]: ZONE FAULT
TROUBLE GROUP [8]: CLOCK LOSS
Press the [7] button to display the zone(s) experiencing a communication, a
fire loop or CleanMeTM trouble.
Press the [8] button to re-program the time.
For technical support in Canada or the U.S., call 1-800-791-1919 for English or 1-866-912-0600 for French, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST.
For technical support outside Canada and the U.S., call 00-1-450-491-7444, Monday to Friday from 8:00 a.m. to 8:00 p.m. EST.
Please feel free to visit our website at www.paradox.ca.
780 Industriel Blvd., Saint-Eustache (Quebec) J7R 5V3 CANADA
Tel.: (450) 491-7444
Fax: (450) 491-2313
www.paradox.ca
PRINTED IN CANADA - 11/2004
DGPNE96-EP07