Samsung PPM42M6S Specifications

Professional PDP
Display
(PLASMA DISPLAY PANEL)
PPM42M6S
PPM42M6H
PPM50M6H
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
Intended for Commercial Use and Operation
ON-SCREEN MENUS
Picture In Picture (PIP)
VIDEO WALL
MDC (Multiple Display Control)
Screen Burn Protection
SRS TruSurroundXT
PPM42M6S: CLASS A, PPM42M6H/50M6H: CLASS B
Register your product at www.samsung.com/global/register
Downloaded From TV-Manual.com Manuals
User Instructions
◆ Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP Display)
on the plasma PDP Display panel for more than 2 hours as it can cause screen image retention.
This image retention is also known as “screen burn”. To avoid such image retention, reduce the
degree of brightness and contrast of the screen when displaying a still image.
◆ Height
The PDP Display can normally operate only under 2000m in height. It might abnormally function at a
place over 2000m in height, so do not install and operate there.
◆ Heat on the top of the PDP Display
The top side of the product may be hot after long periods of use as heat dissipates from the panel
through the vent hole in the upper part of the product.
This is normal and does not indicate any defect or operation failure of the product.
However, children should be prevented from touching the upper part of the product.
◆ The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding
environment such as temperature or humidity. This is normal and not a defect of the unit.
◆ Cell Defects
The PDP Display uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which
require sophisticated technology to produce. However, there may be a few bright or dark pixels on
the screen. These pixels will have no impact on the performance of the product.
◆ Avoid operating the PDP Display at temperatures below 5°C(41°F)
◆ A still image displayed too long may cause permanent damage to the PDP Display Panel
Watching the PDP Display in 4:3 format for a long period of time may leave
traces of borders displayed on the left, right and center of the screen caused
by the difference of light emission on the screen.
Playing a DVD or a game console may cause similar effect to the screen.
Damage caused by the above effect are not covered by the Warranty.
◆ Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may
produce partial afterimages.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images for a
long time.
◆ Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
◆ Installation
Be sure to contact an authorized service center, when installing your PDP Display in a location with
heavy dust, high or low temperatures, high humidity, chemical substance and where it operates
for 24 hours such as the airport, the train station or etc.
Failure to do so may cause a serious damage to your PDP Display.
Installing the product in an airtight place may shorten the lifetime of the product.
© 2006 Samsung Electronics Co., Ltd. All rights reserved.
Downloaded From TV-Manual.com
Manuals
English - 2
Checking Parts
PPM42M6S/
42M6H/50M6H
Owner’s Instructions
Power Cord
Remote Control/
AAA Batteries
Ferrite Cores for
Speaker Wire (2EA)
(Refer to page 14)
Stand-Base
(2EA)
Screws
(4EA)
PC Cable
Downloaded From TV-Manual.com Manuals
English - 3
Contents
◆ FOREWORD
■
User Instructions............................................................................................
2
◆ CONNECTING AND PREPARING YOUR DISPLAY
■
■
■
■
■
■
■
■
■
■
Control Panel.................................................................................................
Infrared Remote Control ................................................................................
Inserting the Batteries in the Remote Control................................................
Assembling the Stand-Base ..........................................................................
Installing the Display on the Wall Attachment Panel .....................................
Installing the Display Vertically ......................................................................
Before Using the Video Wall and the Multiple Display Control function ........
Connecting Speakers ....................................................................................
Switching Your PDP Display On and Off.......................................................
Choosing Your Language..............................................................................
6
8
9
9
10
12
12
13
15
15
◆ USING YOUR DISPLAY
■
■
■
■
■
■
■
■
■
■
■
■
■
Changing the Picture Standard .....................................................................
Customizing the Picture Settings...................................................................
Adjusting the RGB Color (PC Mode) .............................................................
Setting the Picture (PC Mode).......................................................................
Using Zoom function (PC Mode) ...................................................................
Selecting the Picture Size..............................................................................
Freezing the Current Picture .........................................................................
Changing the Sound Standard ......................................................................
Customizing the Sound Settings ...................................................................
Setting the TruSurround XT...........................................................................
Activating Panel Button Lock.........................................................................
Activating Remote Control Button Lock.........................................................
Setting Up Your Personal ID Number............................................................
16
17
18
18
20
21
22
22
23
24
25
26
27
Continued...
Downloaded From TV-Manual.com
Manuals
English - 4
Contents
◆ USING YOUR DISPLAY (CONTINUED)
■
■
■
■
■
■
■
■
■
■
■
Setting the MDC (Multiple Display Control) ...................................................
Preventing Screen Burn-in ............................................................................
Reducing the Effects of Screen Burn ............................................................
Setting the Screen Burn Protection Timer .....................................................
Setting the Multiple Screen............................................................................
Displaying the Setting Information.................................................................
Setting and Displaying the Current Time.......................................................
Switching the PDP Display On and Off Automatically ...................................
Selecting the Fan...........................................................................................
Viewing the Picture in Picture (PIP)...............................................................
Viewing an External Signal Source ...............................................................
28
29
30
31
32
33
33
34
36
37
38
◆ ADDITIONAL INFORMATION AND CONNECTIONS
■
■
■
■
■
■
■
■
■
Connecting to the Audio/Video Input .............................................................
Connecting to the S-Video Input....................................................................
Connecting to the Component Input..............................................................
Connecting to the DVD/DTV Receiver Input .................................................
Connecting to the DVI Input ..........................................................................
Connecting to the PC Input ...........................................................................
Setting up Your PC Software (Windows only) ...............................................
Input Mode (PC/DVI) .....................................................................................
Power Saver (PC1 mode only) ......................................................................
39
40
40
41
41
42
43
44
45
◆ RECOMMENDATIONS FOR USE
■
■
Troubleshooting: Before Contacting Service Personnel................................
Technical Specifications ................................................................................
Symbols
Press
Downloaded From TV-Manual.com Manuals
☛
Important
46
47
➢
Note
English - 5
Control Panel
➢
The actual configuration of your PDP Display may be different,
depending on your model.
Front of the PDP Display
Speaker
(Optional)
Speaker
(Optional)
a
a
b
c
b
SOURCE
Power Indicator
- Select the external input source.
- Store your settings in the menu.
- When the Main menu is displayed on screen,
the Main menu is not operated with source key.
- Power Off; Black
- Power On; Green
MENU
Display the on-screen menu.
- VOL +
- Adjust the volume.
- Adjust an option value respectively.
(VOL + : Enter to the selected menu.)
c
Remote Control Sensor
Aim the remote control towards this spot on the
PDP Display.
SEL
Control the cursor in the menu.
I/
Press to turn the PDP Display on and off.
➢
◆ You can use the SEL
,
buttons to switch on the PDP Display when it is in standby
mode depending on the model.
◆ The VOL -, + and SEL
,
buttons have the same function as the ▲/▼/œ/√ buttons
on the remote control.
◆ If the remote control no longer works or you have misplaced it, you can use the controls
on the panel of the PDP Display.
Continued...
Downloaded From TV-Manual.com
Manuals
English - 6
Rear Panel
a) POWER IN
Connect the supplied power cord.
g) RS-232C
- IN : Used for the MDC function when connecting
b) EXT SPEAKER (8Ω)
Connect external speakers.
c) DVI/PC AUDIO IN
Connect to the audio output jack on your
PC or DVI.
➢
AUDIO is an audio input jack for PC1 and PC2
modes.
d) DVI IN
Connect to the video output jack for device with
DVI output.
e) PC IN1/PC OUT1
- PC IN1 : Connect to the video output jack on
your PC.
- PC OUT1 : Connect to the video input jack on
external devices.
➢
PC or RS-232C output of another PDP
Display.
- OUT : Used for the MDC function when
connecting with RS-232C input of another
PDP Display.
For further details about connections, refer to
Page 12.
h) COMPONENT IN
Video (Y/PB/PR) and audio (L/R) inputs for
component.
i) AV (VIDEO/AUDIO L/R)
- IN : Video and audio inputs for external devices,
such as a camcorder or VCR.
- OUT : Outputs for external devices.
j) S-VIDEO IN
Video input for external devices with an S-Video
output, such as a camcorder or VCR.
f) PC IN2 (BNC)
Connect for RGB HV video signal input from the PC.
➢
➢
➢
“PC Mode” from this page onward means
PC1/PC2 mode using RGB1(PC1) and
RGB2(PC2).
For further details about connection, refer to pages 39~42.
Whenever you connect an audio or video system to your PDP Display, ensure that all elements are
switched off. Refer to the documentation supplied with your equipment for detailed connection
instructions and associated safety precautions.
Downloaded From TV-Manual.com Manuals
English - 7
Infrared Remote Control
PDP DISPLAY ON
PDP DISPLAY OFF
DIRECT CHANNEL SELECTION
NOT AVAILABLE
VOLUME INCREASE
TEMPORARY SOUND SWITCH-OFF
PICTURE STILL
NEXT CHANNEL
EXTERNAL INPUT SELECTION
VOLUME DECREASE
PREVIOUS CHANNEL
SETTING THE TIMER
INFORMATION DISPLAY
MENU DISPLAY
EXIT FROM ANY DISPLAY
MOVE TO THE REQUIRED MENU
OPTION/
ADJUST AN OPTION VALUE
RESPECTIVELY
CONFIRM YOUR CHOICE
(STORE OR ENTER)
PICTURE EFFECT SELECTION
AUTO ADJUSTMENT IN PC MODE
PIP FUNCTIONS:
- PIP ACTIVATION OR DEACTIVATION
(PIP)
- SOURCE SELECTION (SOURCE)
➢
SOUND EFFECT SELECTION
PICTURE SIZE
MULTIPLE DISPLAY CONTROL
SCREEN EFFECT SELECTION
(BURNING PROTECTION)
The performance of the remote control may be affected by bright light.
Downloaded From TV-Manual.com
Manuals
English - 8
Inserting the Batteries in the Remote Control
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the PDP Display
◆ Find that the remote control is no longer operating
correctly
1
Remove the cover on the rear of the remote control by pressing
the symbol ( ) downwards and then pulling firmly to remove it.
2
Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
◆ - on the battery against - on the remote control
◆ + on the battery against + on the remote control
3
Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
Do not mix battery types, i.e. alkaline and manganese.
Assembling the Stand-Base
1
➢
Assemble the PDP Display with the stand and firmly
secure the PDP Display using 4 screws provided.
Two or more people should carry the PDP Display.
Never lay the PDP Display on the floor because of
possible damage to the screen.
Always store the PDP Display upright.
(PPM42M6S/42M6H/50M6H)
Downloaded From TV-Manual.com Manuals
English - 9
Installing the Display on the Wall Attachment Panel
➢
Refer to the correct installation guide according to your wall bracket.
Installation Notes
◆ Contact a technician for installing the wall bracket.
◆ Samsung Electronics is not responsible for any damages to the product or harm to customers when
the installation is done by the customer.
◆ This product is for installing on cement walls. The product may not stay in place when installed on
plaster or wood.
Components
◆ Only use the components and accessories shipped with the product.
Wall Bracket
Hinge
Accessories
Plastic Hanger: 4
1
Left: 1
Screw
Right: 1
:4
Screw
: 11
Anchor : 11
Wall Bracket Assembly
1
Insert and tighten the Captive Screw in
the direction of the arrow.
When done, mount the wall bracket on
the wall.
2
Captive Screw
Before drilling into the wall, check if the length
between the two locking holes at the back of
the product is correct.
If the length is too short or long, loosen all or
some of the 4 screws on the wall bracket to
adjust the length.
Length between the
two locking holes
Wall Bracket
Hinge (Left)
There are two hinges
(left and right). Use the
correct one.
3
Hinge (Right)
Check the installation diagram and mark the drill
points on the wall. Use the 5.0 mm bit to drill holes
deeper than 35 mm.
Fix each anchor in the corresponding hole.
Match each of the brackets and hinge holes to the
corresponding anchor holes and insert and tighten
the 11 screws .
Continued...
Downloaded From TV-Manual.com
Manuals
English - 10
To mount the product on the wall bracket
◆ The shape of the product may vary depending on the model. (The assemblies of the plastic hanger
and the screw are the same)
1
Remove the 4 screws on the back of the product.
2
Insert the screw into the plastic hanger.
(See the figure below)
☛
3
Tighten the 4 screws in step 2 (plastic hanger
+ screw ) to the rear holes of the product.
4
◆ Mount the product on the wall bracket
and make sure it is properly fixed to
the left and right plastic hangers.
◆ Be careful when installing the product
on the bracket as fingers can be
caught in the holes.
◆ Make sure the wall bracket is securely
fixed to the wall, or the product may not
stay in place after installation.
Remove safety pin (#) and insert the 4 product
holders into the corresponding bracket holes (!). Then
place the product (@) so that it is firmly fixed to the
bracket. Make sure to reinsert and tighten the safety
pin (#) to securely hold the product to the bracket.
PDP Display
Wall Bracket Wall
Wall Bracket Angle Adjustment
➢
o
Adjust the bracket angle to -2 before installing it on the wall.
1
Fix the product to the wall bracket.
2
Hold the product at the top in the center and pull it
forward (direction of the arrow) to adjust the angle.
(See the figure to the right)
3
You can adjust the bracket angle between -2° and 15°.
Downloaded From TV-Manual.com Manuals
Make sure to use the top center,
and not the left or the right side of
the product to adjust the angle.
English - 11
Installing the Display Vertically
➢
❋ Samsung shall not be liable for
damages caused by installing the
product at the different direction from
the figure below.
The Fan function for the model PPM42M6S is not
available.
You can install the PDP Display vertically.
In this case, the fan automatically works.
If you wish to stop the fan, position the PDP
Display horizontally and then set “Fan” to “Off”
in the “Function” menu.
Please use the wall attachment panel exclusively
when installing vertically. And you have to put the
bottom of the PDP Display with menu buttons on
the left when viewed from front.
Before Using the Video Wall and the Multiple Display Control function
Example for 2x2 Video Wall function
1
Please create ID for each PDP Display before
installing them close together. It may be difficult to
create IDs when operating the remote control for
PDPs that are installed close to each other.
2
For details about Video Wall configuration and
operation, refer to “Setting the Multiple Screen”
on page 32.
Example for 2x2 Video Wall connections
Rear of the PDP Display
Rear of the PDP Display
②
①
➢
◆ You can connect a Composite (Video) without
a distributor as you would connect a PC.
◆ Select ID input on the menu. Use the numeric
buttons to enter the ID for PDP Display
adjustment. You can operate the remote
control only for the PDP Display that has been
selected.
◆ For details about Multiple Display Control, refer
to “Setting the MDC (Multiple Display Control)”
on page 28.
Downloaded From TV-Manual.com
Manuals
English - 12
Example for Multiple Display Control connections
Connecting Speakers
➢
1
Speakers are optional. You have to purchase the speakers
additionally.
Remove the screws on the rear of the PDP Display.
PPM42M6S
PPM42M6H
PPM50M6H
2
Hang the two “T” shaped hangers
on the square holes on the rear of
the PDP Display.
3
Tighten the PDP Display and the speaker bracket using the screws removed from the PDP Display.
PPM42M6S
PPM42M6H
➢
PPM50M6H
When moving your PDP Display, do NOT hold the speaker connected to your PDP Display. It may
damage the bracket clamping the speaker and your PDP Display together and result in a drop of
your PDP Display and a risk of personal damage and injury.
Continued...
Downloaded From TV-Manual.com Manuals
English - 13
Connect the speaker audio cable to the external speaker output jack on the rear of the PDP Display
matching the “+” and “-” ends of the cable with the diagram on the PDP Display.
➢
◆ The speakers MUST have a power handling capability of 10 watts minimum (impedance 8Ω).
◆ When you connect the speaker wire to the external speaker out connector, first bind the
speaker wire round the ferrite core to secure it.
Ferrite Cores
The ferrite cores are used to attenuate undesired signals.
When connecting cables, attach one of these ferrite cores to the cable
near the connector.
Downloaded From TV-Manual.com
Manuals
English - 14
Switching Your PDP Display On and Off
The mains lead is attached to the rear of your PDP Display.
1
Plug the mains lead into an appropriate socket.
Result:
➢
Front of the PDP Display
The Standby indicator on the front of the PDP Display
lights up.
The main voltage is indicated on the rear of the PDP
Display and the frequency is 50 or 60Hz.
2
Press the “
” button on the front of the PDP Display (or the ON
( ) button on the remote control) to switch the PDP Display on.
3
To switch your PDP Display off, press the “
the OFF ( ) button on the remote control).
” button again (or
Choosing Your Language
When you start using your PDP Display for the first time, you must
select the language which will be used for displaying menus and
indications.
Setup
Time
Language
1
Press the MENU (
) button.
The main menu is displayed.
Result:
2
Press the … or † button to select Setup.
The Setup menu is displayed.
Result:
3
Press the ENTER (
4
Press the … or † button to select Language.
Press the ENTER (
) button.
The available languages are listed.
Result:
Move
5
6
: English
PC
Enter
Return
) button.
Select the appropriate language by pressing the … or † button.
Press the ENTER (
) button.
Setup
Time
Language
PC
Deutsch
Italiano
Español
Português
Press the EXIT button to exit.
†
Move
Downloaded From TV-Manual.com Manuals
English
: English
Français
Enter
English - 15
Return
Changing the Picture Standard
You can select the type of picture which best corresponds to your
viewing requirements.
Picture
Mode
: Dynamic
Color Control
Size
1
Press the MENU (
) button.
The main menu is displayed.
Result:
2
Press the … or † button to select Picture.
The Picture menu is displayed.
Result:
3
Press the ENTER (
) button.
The Mode is selected.
Result:
4
Press the ENTER (
: 16:9
PIP
Move
Enter
Return
Mode
Mode
Contrast
Brightness
Sharpness
Color
Tint
G 50
Colour Tone
Reset
Move
: Dynamic
100
50
75
55
R 50
Move
5
Enter
The Mode menu is displayed.
Press the ENTER (
Result:
) button.
The following options are available.
Dynamic - Standard - Movie - Custom
: Cool1
Return
Mode
Mode
Contrast
Brightness
Sharpness
Color
Tint
G 50
Colour Tone
Reset
Result:
) button again.
6
Select the required option by pressing the … or † button.
7
Press the ENTER (
8
Press the EXIT button to exit.
) button.
: Dynamic
Dynamic
100
50
75
Custom 55
R 50
: Cool1
Standard
Movie
Enter
Return
Downloaded From TV-Manual.com
Manuals
English - 16
➢
You can also set these options simply by pressing the
P.MODE (Picture Mode) button on the remote
control.
Customizing the Picture Settings
Your PDP Display has several setting options that allow you to
control the picture quality.
1
Picture
Mode
Press the MENU (
) button.
Result:
The main menu is displayed.
: Dynamic
Color Control
Size
: 16:9
PIP
2
Press the … or † button to select Picture.
Result:
The Picture menu is displayed.
3
Press the ENTER (
) button.
Result:
The Mode is selected.
4
Press the ENTER (
) button again.
Result:
The Mode menu is displayed.
5
Move
Dynamic - Standard - Movie - Custom
Select the required option by pressing the … or † button.
7
Press the ENTER (
8
Select the required option by pressing the … or † button.
Result:
The following options are available.
9
10
11
Contrast - Brightness - Sharpness - Color Tint (NTSC only)
◆
Contrast - Brightness - Color : PC or DVI
Mode.
Press the ENTER (
) button.
Result:
The horizontal bar is displayed.
Press the œ or √ button until you reach the optimal
setting.
➢
◆ Press the … or † button to select other option(s).
◆ The settings values may vary depending on the input
source. (ex. AV, Component, PC, or DVI.)
Press the MENU ( ) button to return to Mode menu.
Press the … or † button to select Colour Tone.
) button.
Press the ENTER (
Select the required option by pressing the … or † button.
Result:
The following options are available.
Cool2 - Cool1 - Normal - Warm1 - Warm2
12
Press the ENTER (
13
To return the factory defaults, select Reset by pressing the … or
† button. Press the ENTER (
) button.
Result:
The previously adjusted settings will be reset to the
factory defaults.
➢
➢
Move
) button.
◆
) button.
: Dynamic
100
50
75
55
R 50
: Cool1
Enter
Return
Contrast
100
Mode
Mode
Contrast
Brightness
Sharpness
Color
Tint
G 50
Colour Tone
Reset
Move
: Dynamic
100
50
75
Cool1
55
Normal R 50
Warm1
: Cool
1
Warm2
Cool2
Enter
Return
Mode
Mode
Contrast
Brightness
Sharpness
Color
Tint
G 50
Colour Tone
Reset
Move
: Dynamic
100
50
75
55
R 50
: Cool1
Enter
The reset function is set for each mode (Dynamic,
Standard, Movie, or Custom).
The reset function is also set for each Colour Tone (Cool2,
Cool1, Normal, Warm1, or Warm2).
14 Press the EXIT button to exit.
Downloaded From TV-Manual.com Manuals
Return
Mode
Mode
Contrast
Brightness
Sharpness
Color
Tint
G 50
Colour Tone
Reset
Press the ENTER (
) button.
Result:
The following options are available.
6
Enter
English - 17
Return
Adjusting the RGB Color (PC Mode)
➢
1
Preset to the PC mode by pressing the SOURCE button.
Press the MENU (
) button.
Picture
Mode
Result:
: Dynamic
Color Control
Size
2
: 16:9
PIP
Press the … or † button to select Picture.
Result:
Move
Enter
Return
Color Control
Red
50
Green
50
Blue
50
Enter
Red
The Picture menu is displayed.
3
Press the ENTER (
4
Press the … or † button to select Color Control.
Press the ENTER (
) button.
5
Select the required option (Red, Green, or Blue) by pressing the
… or † button.
6
Press the ENTER (
Result:
Move
The main menu is displayed.
Return
➢
) button.
) button.
The horizontal bar is displayed.
Press the œ or √ button until you reach the optimal
setting.
Press the … or † button to select other option(s).
7
Press the ENTER (
8
Press the EXIT button to exit.
) button.
50
Setting the Picture (PC Mode)
➢
Setup
1
Time
Language
Preset to the PC mode by pressing the SOURCE button.
Press the MENU (
Result:
: English
PC
2
Enter
Return
The main menu is displayed.
Press the … or † button to select Setup.
Result:
Move
) button.
The Setup menu is displayed.
3
Press the ENTER (
4
Press the … or † button to select PC.
Press the ENTER (
) button.
PC
Image Lock
Result:
) button.
The PC menu is displayed.
Position
Auto Adjustment
Image Reset
Zoom
Move
Enter
5
Press the ENTER (
) button to select Image Lock.
Return
Continued...
Downloaded From TV-Manual.com
Manuals
English - 18
6
Press the … or † button to select the option (Coarse or Fine) to
be adjusted. Press the ENTER (
) button.
Result:
➢
The horizontal bar is displayed.
Press the œ or √ button until you reach the optimal
setting.
Press the ENTER (
8
Press the MENU (
) button.
The PC menu is displayed again.
Coarse
Adjust the position by pressing the …, †, œ, or √ button.
11
Press the ENTER (
12
Press the … or † button to select Auto Adjustment.
Press the ENTER (
) button.
Position
) button.
The screen quality and position are automatically reset.
The settings are all finished, and the PDP Display will
automatically return to the previous picture.
To return the factory defaults, select Image Reset by pressing
the … or † button. Press the ENTER (
) button.
Result:
Return
50
Press the … or † button to select Position.
Press the ENTER (
) button.
Result:
Enter
) button.
10
14
30
Move
Result:
13
50
Fine
Press the … or † button to select other option(s).
7
9
Image Lock
Coarse
The previously adjusted settings will be reset to the
factory defaults.
Press the EXIT button to exit.
Downloaded From TV-Manual.com Manuals
Move
Enter
Auto Adjustment in Progress
Please wait.
Image Reset is completed.
Return
English - 19
Return
Using Zoom function (PC Mode)
➢
Preset to the PC mode by pressing the SOURCE button.
a
1
Press the MENU (
) button.
Setup
Result:
Time
Language
: English
2
PC
Press the … or † button to select Setup.
Result:
Move
Enter
Return
Press the ENTER (
4
Press the … or † button to select PC.
Press the ENTER (
) button.
Result:
Position
Auto Adjustment
Image Reset
Zoom
Enter
6
Press the ENTER (
) button again.
Select the required option by pressing the … or † button.
Return
:0
1
2
◆ Option 0 represents a normal screen.
The greater the number, the more magnified the screen.
◆ You can select the position and reset functions by
selecting options 1 through 6. (If you select option 0, the
position and reset functions are not selected.)
0
Reset
The following options are available.
0-1-2-3 -4 -5 -6
➢
Position
The PC menu is displayed.
Press the … or † button to select Zoom.
Press the ENTER (
) button.
Zoom
Zoom
) button.
5
Result:
Move
The Setup menu is displayed.
3
PC
Image Lock
The main menu is displayed.
3
◆ If you have selected the Zoom function as between 1~6,
you will not be able to select the Auto Adjustment function.
4
5
6
Move
Enter
Return
7
Press the ENTER (
8
Press the … or † button to select Position.
Press the ENTER (
) button.
9
Adjust the position by pressing the …, †, œ, or √ button.
10
Press the MENU (
Zoom
Zoom
:1
Position
) button.
Reset
Result:
Move
Enter
Return
11
Zoom
:1
12
Position
Reset
Move
Enter
Return
Downloaded From TV-Manual.com
Manuals
English - 20
The Zoom menu is displayed again.
To return the factory defaults, select Reset by pressing the … or
† button. Press the ENTER (
) button.
Result:
Zoom
) button.
The previously adjusted settings will be reset to the
factory defaults.
Press the EXIT button to exit.
Selecting the Picture Size
You can select the picture size which best corresponds to your viewing
requirements.
Picture
Mode
1
Press the MENU (
Result:
) button.
The main menu is displayed.
: Dynamic
Color Control
Size
: 16:9
PIP
Press the … or † button to select Picture.
2
Result:
The Picture menu is displayed.
3
Press the ENTER (
4
Press the … or † button to select Size.
Press the ENTER (
) button.
5
Select the required option by pressing the … or † button.
Result:
◆ 4:3
Enter
Return
) button.
Size
16:9
Wide 4:3
Zoom
4:3
The following options are available.
◆ 16:9
◆ Wide 4:3
◆ Zoom
Move
: Sets the picture to 16:9 wide mode.
: Magnify the size of the picture more than 4:3.
Move the screen up/down using the … or †
button after selecting the
by pressing the √
or ENTER (
) button.
: Magnify the size of the picture vertically on
screen.
: Sets the picture to 4:3 normal mode.
Move
Enter
Return
PC to DVI Mode
Size
16:9
Wide 4:3
6
Press the ENTER (
7
Press the EXIT button to exit.
) button.
Zoom
4:3
➢
◆ You can select these options simply by pressing the P.SIZE
button on the remote control.
Move
Enter
◆ If you change the picture size when PIP is On, PIP will
automatically be turned Off.
◆ Depending on the input source, the P.SIZE options may vary.
◆ PC and DVI modes, only 16:9 & 4:3 modes can be selected.
Positioning and Sizing the screen using Zoom
➢
◆ Resizing the screen using the Zoom enables the positioning
and sizing of the screen to up/down direction using the … or
† button as well as the screen size.
◆ Move the screen up/down using the … or † button after
selecting the
by pressing the œ or √ button.
◆ Resize the screen vertically using the … or † button after
selecting the
by pressing the œ or √ button.
(Pressing the … button extends it upward and pressing the
† button extends it downward.)
◆ Screen enlargement operates only in Video/S-Video/
Component input modes.
◆ PC/DVI modes prevent the screen enlargement function.
Downloaded From TV-Manual.com Manuals
English - 21
Return
Freezing the Current Picture
You can freeze the picture when watching a moving picture simply
by pressing the “STILL” button. To return to normal viewing, press
it again.
➢
In PIP mode, Still function will be applied to the main and
sub picture at the same time.
Changing the Sound Standard
You can select the type of special sound effect to be used when
watching a given broadcast.
Sound
Mode
Equalizer
SRS TSXT
: Custom
1
Press the MENU (
Result:
Result:
Enter
The Sound menu is displayed.
Return
3
Press the ENTER (
Result:
Sound
Mode
Equalizer
SRS TSXT
The main menu is displayed.
Press the ▲ or ▼ button to select Sound.
2
Move
) button.
: Off
: Custom
Standard
Music
: Off Movie
4
) button.
The Mode is selected.
Press the ENTER (
) button again.
Select the required option by pressing the ▲ or ▼ button.
Speech
Result:
Custom
The following options are available.
Standard - Music - Movie - Speech - Custom
Move
Enter
Return
5
Press the ENTER (
6
Press the EXIT button to exit.
➢
Downloaded From TV-Manual.com
Manuals
English - 22
) button.
You can select these options by simply pressing the
S.MODE (Sound Mode) button on the remote control.
Customizing the Sound Settings
Your PDP Display has several settings which allow you to control
the sound quality.
1
Press the MENU (
Result:
) button.
The main menu is displayed.
Sound
Mode
Equalizer
SRS TSXT
: Custom
: Off
Press the … or † button to select Sound.
2
Result:
The Sound menu is displayed.
Move
3
Press the ENTER (
4
Press the … or † button to select Equalizer.
Press the ENTER (
) button.
Result:
5
The Equalizer menu is displayed.
Select the required option (balance or equalizer) by pressing the
œ or √ button.
Press the … or † button until you reach the optimal setting.
Press the ENTER (
) button.
7
R
+
+
0
0
-
L
Move
-
100Hz 300Hz 1KHz 3KHz 10KHz
Adjust
Press the EXIT button to exit.
➢
Return
Equalizer
Balance
6
Enter
) button.
If you make any changes to the sound settings, the sound
standard is automatically switched to Custom.
Downloaded From TV-Manual.com Manuals
English - 23
Return
Setting the TruSurround XT
Sound
Mode
Equalizer
SRS TSXT
: Custom
: Off
TruSurround XT is a patented SRS technology that solves the
problem of playing 5.1 multichannel content over two speakers.
TruSurround delivers a compelling, virtual surround sound
experience through any two-speaker playback system, including
internal PDP Display speakers. It is fully compatible with all
multichannel formats.
1
Press the MENU (
Result:
Move
Enter
Press the … or † button to select Sound.
Result:
Sound
The Sound menu is displayed.
: Custom
3
Press the ENTER (
: Off Off
4
Press the … or † button to select SRS TSXT.
Press the ENTER (
) button.
5
Select Off or On by pressing the … or † button.
Press the ENTER (
) button.
6
Press the EXIT button to exit.
On
Move
The main menu is displayed.
Return
2
Mode
Equalizer
SRS TSXT
) button.
Enter
Return
Downloaded From TV-Manual.com
Manuals
English - 24
) button.
Activating Panel Button Lock
This feature allows you to lock the PDP Display panel buttons so
that it cannot be operated via the PDP Display panel. It can,
however, still be operated via the remote control. Only remote
control can release the panel lock setting, so keep the remote
control away from unauthorized users.
Function
Screen Burn Protection
Safety Lock
Multi Control
Video Wall
Fan
1
Press the MENU (
Result:
: Off
) button.
The main menu is displayed.
Move
2
Enter
Return
Press the ▲ or ▼ button to select Function.
Result:
The Function menu is displayed.
3
Press the ENTER (
4
Press the ▲ or ▼ button to select Safety Lock.
Press the ENTER (
) button.
5
Press the ENTER (
6
Select Off or On by pressing the ▲ or ▼ button.
Press the ENTER (
) button.
7
Press the EXIT button to exit.
) button.
Safety Lock
Key Lock
: Off
IR Lock
Change PIN
) button again to select Key Lock.
Move
Enter
Return
Safety Lock
Key Lock
: Off
IR Lock
Off
On
Change PIN
Move
Downloaded From TV-Manual.com Manuals
Enter
English - 25
Return
Activating Remote Control Button Lock
This feature allows you to lock the remote control so that it cannot
be operated via the remote control. It can, however, still be
operated via the PDP Display Panel buttons.
Function
Screen Burn Protection
Safety Lock
Multi Control
1
Video Wall
Fan
Press the MENU (
: Off
Result:
Enter
Return
Safety Lock
Key Lock
: Off
IR Lock
Result:
Enter
Return
Press the ENTER (
4
Press the ▲ or ▼ button to select Safety Lock.
Press the ENTER (
) button.
5
Press the ▲ or ▼ button to select IR Lock.
Press the ENTER (
) button.
6
Press the EXIT button to exit.
➢
IR Lock : On
Downloaded From TV-Manual.com
Manuals
English - 26
The Function menu is displayed.
3
Change PIN
Move
The main menu is displayed.
Press the ▲ or ▼ button to select Function.
2
Move
) button.
) button.
When IR Lock is set to On, you will not be able to use the
remote control even if the remote control button is pressed.
To cancel the Remote Control Button Lock, press “0000”
using the numeric buttons on the remote control then, ‘IR
LOCK : OFF’ is display.
Setting Up Your Personal ID Number
This feature sets viewing restrictions and prevents unauthorized
access to your PDP Display through the PIN (Personal
Identification Number), which is a 4 digit number.
Function
Screen Burn Protection
Safety Lock
1
Press the MENU (
Result:
) button.
The main menu is displayed.
Multi Control
Video Wall
Fan
: Off
Press the ▲ or ▼ button to select Function.
2
Result:
The Function menu is displayed.
3
Press the ENTER (
4
Press the ▲ or ▼ button to select Safety Lock.
Press the ENTER (
) button.
) button.
5
Press the ▲ or ▼ button to select Change PIN.
Press the ENTER (
) button.
6
Press the number buttons to enter your current 4-digit pin number.
➢
Move
Enter
Return
Safety Lock
Key Lock
: Off
IR Lock
Change PIN
Move
Enter
Return
The default pin number for a new PDP Display set is “0000”.
7
Press the numeric buttons to enter your new 4-digit pin number.
Re-enter your new pin number to confirm.
8
Press the EXIT button to exit.
Change PIN
Enter PIN
Enter New PIN
➢
If you forget the pin number, press the remote control
buttons in the following sequence, which resets the pin to
0-0-0-0: MUTE, 1, 8, 6.
0 .. 9: Enter PIN
Return
Change PIN
Enter PIN
*
*
*
Enter New PIN
0 .. 9: Enter PIN
Downloaded From TV-Manual.com Manuals
English - 27
*
Return
Setting the MDC (Multiple Display Control)
This function enables you to easily control the connected PDP
Displays on the PC by specifying IDs to connected PDP Displays.
Function
Screen Burn Protection
1
Safety Lock
Press the MENU (
Multi Control
Result:
Video Wall
Fan
: Off
Enter
:
00
ID Input
:
--
3
Press the ENTER (
4
Press the ▲ or ▼ button to select Multi Control.
5
Press the ENTER (
Result:
Move
Enter
:
ID Input
:
Enter
Press the ▲ or ▼ button to select ID Input.
Press the ENTER (
) button.
8
Enter ID input number by using the numeric buttons.
9
Press the EXIT button to exit.
Return
Multi Control
ID Setup
:
00
ID Input
:
--
➢
➢
0 .. 9: Enter ID Input Number
Downloaded From TV-Manual.com
Manuals
English - 28
The Multi Control menu is displayed with the ID
Setup selected.
7
➢
Move
) button.
Press the ENTER (
) button again.
Select the ID setup number by using the numeric buttons.
Press the ENTER (
) button.
Return
00
--
) button.
6
Multi Control
ID Setup
The Function menu is displayed.
Return
Multi Control
ID Setup
The main menu is displayed.
Press the ▲ or ▼ button to select Function.
2
Result:
Move
) button.
➢
To operate the multi control function, PDP1 and PDP2 should
be set in the ID Setup mode. When entering the ID Input
number of PDP1 while the PDP Display is set in the ID Input
mode, only PDP1 is switched to the Menu screen and you can
operate the remote control. At this time, PDP2 doesn't operate
with the remote control and displays the standby mode of ID
Input.
For further details, refer to the MDC program guide.
You can select these options by simply pressing the MDC
(Multiple Display Control) button on the remote control.
Refer to the following Web site for information about MDC
programs and protocol documents:
http://www.samsung.com/support/productsupport/downloa
d/index.aspx
Preventing Screen Burn-in
To reduce the possibility of screen burn, this unit is equipped with
screen burn prevention technology. This technology enables you to
set picture movement up/down (Vertical Line) and side to side
(Horizontal Dot). The Time setting allows you to program the time
between movement of the picture in minutes.
Function
Screen Burn Protection
Safety Lock
Multi Control
Video Wall
1
Press the MENU (
Result:
Fan
) button.
: Off
The main menu is displayed.
Move
2
Enter
Return
Press the … or † button to select Function.
Result:
The Function menu is displayed.
Screen Burn Protection
3
Press the ENTER (
4
Press the … or † button to select Screen Burn Protection.
Press the ENTER (
) button.
) button.
Pixel Shift
All White
Signal Pattern
Inverse
Bar
Result:
5
➢
8
Enter
Return
The Pixel Shift menu is selected.
Pixel Shift
You can select these options by simply pressing the
S.EFFECT button on the remote control.
Pixel Shift: Using this function, you can minutely move
pixels on the PDP in horizontal or vertical direction to
prevent after image on the screen.
Select the required option (Horizontal Dot, Vertical Line, or
Time) by pressing the … or † button.
Press the ENTER (
) button.
Pixel Shift
: Off
Horizontal Dot : 4
Off
On
Vertical Line
:4
Time
: 4 min.
Move
Enter
Return
Pixel Shift
Pixel Shift
: On
Horizontal Dot : 4
Vertical Line
:4
Time
: 4 min.
Press the … or † button until you reach the optimal setting.
Press the ENTER (
) button.
➢
Optimum condition for pixel shift;
Horizontal Dot
Vertical Line
Time
9
Timer
) button again.
Press the ENTER (
) button.
Select On by pressing the … or † button for making the screen
move per regular hour and preventing the residual image.
Press the ENTER ( ) button.
➢
7
Bar & Inverse
Move
Press the ENTER (
Result:
6
The Screen Burn Protection menu is displayed
with the Pixel Shift selected.
PPM42M6S
2
4
4 min.
PPM42M6H
2
4
4 min.
Move
Enter
PPM50M6H
4
4
4 min.
Press the EXIT button to exit.
Downloaded From TV-Manual.com Manuals
English - 29
Return
Reducing the Effects of Screen Burn
If screen burn has occurred, you can select a white screen or
inverse function to help remove screen burn artifacts.
Function
Screen Burn Protection
1
Safety Lock
Press the MENU (
Result:
Multi Control
) button.
The main menu is displayed.
Video Wall
Fan
Press the … or † button to select Function.
2
: Off
Result:
Move
Enter
Return
Screen Burn Protection
3
Press the ENTER (
4
Press the … or † button to select Screen Burn Protection.
) button.
Press the ENTER (
Pixel Shift
Result:
All White
Signal Pattern
Inverse
Bar & Inverse
Timer
Move
Enter
➢
Return
Screen Burn Protection
➢
Pixel Shift
All White
Signal Pattern
Inverse
Bar
➢
Bar & Inverse
Timer
Move
Enter
Return
➢
➢
6
The Screen Burn Protection menu is displayed
with the Pixel Shift selected.
All White: This function removes after images on the
screen by changing the color of pixels to white. Use this
function when there are remaining after images or symbols
on the screen especially when you displayed a still image
on the screen for a long time.
Signal Pattern: This function removes after images on
the screen by moving all the pixels on the PDP Display
according to a pattern. Use this function when there are
remaining after images or symbols on the screen especially
when you displayed a still image on the screen for a long time.
Inverse: This function removes after images on the screen
when the PDP Display is remained on for proloned periods
by converting RGB input signal into GBR. Compared to All
White and Signal Pattern function, this function can reduce
burn in when you watch PDP Display. Using the inverse
function when you watch PDP Display can cause the color
reversal on the screen. (ex. The colors in red line can be
shown as the colors in green line on the screen.)
Bar: This function removes after images on the screen when the
PDP Display is remained on for proloned periods by crossing the
vertical white bar from left to right. Compared to All White and
Signal Pattern function, this function can reduce burn in when
you watch PDP Display. Using the bar mode function when you
watch PDP Display can cause poor picture quality with the
vertical white bar appeared on some parts of the screen.
Bar & Inverse: This function removes after images on the
screen when the PDP Display is remained on for proloned
periods by converting RGB input signal into GBR and crossing
the vertical white bar from left to right. Compared to All White and
Signal Pattern function, this function can reduce burn in when
you watch PDP Display. Using the inverse function when you
watch PDP Display can cause the color reversal on the screen.
(ex. The colors in red line can be shown as the colors in green
line on the screen.)
Press the ENTER (
➢
➢
Downloaded From TV-Manual.com
Manuals
English - 30
) button.
Press the … or † button to select the option (All White, Signal
Pattern, Inverse, Bar or Bar & Inverse). Press the ENTER
(
) button.
5
Bar
The Function menu is displayed.
) button.
To remove after images on the screen, use either All White,
Signal Pattern, Inverse, Bar or Bar & Inverse function.
Although both of the four functions remove after images on the
screen, “Signal Pattern” is more effective.
The after image removal function has to be executed for a long
time (approximately 1 hour) to effectively remove after images on
the screen. If after image is not removed after the execution of the
function, repeat the function additionally.
Setting the Screen Burn Protection Timer
You can set the timer for Screen Burn Protection (hours, minutes).
If you start the operation to erase any residual image, the operation
will be performed for the set period of time and then automatically
finish.
Screen Burn Protection
Pixel Shift
All White
Signal Pattern
1
Press the MENU (
Result:
) button.
The main menu is displayed.
Inverse
Bar
Bar & Inverse
Timer
2
Press the … or † button to select Function.
Result:
3
Move
5
Press the ENTER (
Timer
) button.
Press the … or † button to select Screen Burn Protection.
Press the ENTER (
) button.
The Timer menu is displayed.
6
Press the ENTER (
7
Select On by pressing the … or † button.
Press the ENTER (
) button.
: Off
Off
: SignalOn
Pattern
Period
: 1 Hour
Time
: 30 min.
◆ Mode
◆ Period
◆ Time
Move
Enter
Return
) button again.
Select the required option by pressing the … or † button.
Result:
9
Mode
Press the … or † button to select Timer.
Press the ENTER (
) button.
Result:
8
Return
The Function menu is displayed.
Timer
4
Enter
Timer
Timer
: On
Mode
: Signal
Pattern
All White
: Signal
01 Pattern
Hr.
:
05 min
Inverse
Period
Time
The following options are available.
: All White, Signal Pattern, Inverse,
Bar, Bar & Inverse
: Hour(1~24)
: Minute(1~30)
Press the EXIT button to exit.
Bar
Bar & Inverse
Move
Enter
Return
Timer
Timer
: On
Mode
: All White
▲
Period
: 01 01
▲
: 30 min.
Time
Move
Enter
Return
Timer
Timer
: All White
Period
: 1 Hour
▲
Time
: 30 30
Move
Downloaded From TV-Manual.com Manuals
: On
Mode
▲
Enter
English - 31
Return
Setting the Multiple Screen
You can get various display effects with many PDPs.
Function
1
Screen Burn Protection
Press the MENU (
) button.
Safety Lock
Result:
Multi Control
The main menu is displayed.
Video Wall
Fan
Press the ▲ or ▼ button to select Function.
2
: Off
Result:
Move
Enter
Return
3
Press the ENTER (
4
Press the ▲ or ▼ button to select Video Wall.
5
Press the ENTER (
Video Wall
Video Wall
: Off
Format
: Full
Result:
Screen Divider
Move
Enter
Off
: Full On
Press the ▲ or ▼ button to select Format.
Press the ENTER (
) button.
8
Select the required option by pressing the ▲ or ▼ button.
Result:
➢
Enter
Return
: On
Format
: Full Full
Screen Divider
Move
Natural
Enter
The following options are available.
◆ Full : This option displays divided images on multiple
PDP Displays without missing parts as if only the
viewable part of the separate PDP Displays were
simply part of a large single PDP Display.
◆ Natural : This option displays divided images on multiple
PDP Displays as if the separate PDP Displays
were simply part of a large single PDP Display.
Therefore there are missing parts on the edge
of the PDP Displays.
Video Wall
Video Wall
The Video Wall menu is displayed with the Video
Wall selected.
7
Screen Divider
Move
) button.
Press the ENTER (
) button.
Select On by pressing the ▲ or ▼ button.
Press the ENTER (
) button.
Return
: Off
Format
) button.
6
Video Wall
Video Wall
The Function menu is displayed.
Press the ENTER (
Return
Screen Divider
) button.
9
Press the ▲ or ▼ button to select Screen Divider.
Press the ENTER (
) button.
10
Select the option (2x2, 3x3, 4x4, 5x1, or 1x5) by pressing the
▲ or ▼ button. Press the ENTER (
) button.
11
Press the œ or √ button to select the position of the screens.
12
Press the EXIT button to exit.
2x2
3x3
4x4
5x1
1
2
3
4
➢
1x5
Move
Enter
Return
Downloaded From TV-Manual.com
Manuals
English - 32
◆ The PIP function and Picture Size do not work during
the Video Wall operation.
◆ The VESA Format input does not support the Video
Wall function in DVI mode.
Displaying the Setting Information
You can view the setting status you select by pressing the “INFO”
button on the remote control.
AV
Picture
Sound
SRS TSXT
-- : --
: Dynamic
: Custom
: Off
Setting and Displaying the Current Time
You can set the PDP Display’s clock so that the current time is
displayed by pressing the “INFO (
)” button. You must also set
the time if you wish to use the automatic on or off timers.
Setup
Time
Language
1
Press the MENU (
) button.
The main menu is displayed.
Result:
2
Press the … or † button to select Setup.
The Setup menu is displayed.
Result:
3
Press the ENTER (
4
Press the … or † button to select Time.
) button.
Press the ENTER (
The Clock Set is selected.
Result:
Press the ENTER (
6
Press the œ or √ button to select Hour or Minute.
Set these by pressing the … or † button.
Enter
Return
Time
Clock Set
12: 00
On Timer
12: 00
Off
Off Timer
12: 00
Off
Move
Enter
) button again.
You can set the hour and minute directly by pressing
the numeric buttons on the remote control.
7
Press the ENTER (
8
Press the EXIT button to exit.
➢
Move
) button.
5
➢
: English
PC
) button.
In the event of a power interruption or the set being turned off at
the supply, the settings for the Clock will be lost.
Clock Set
Hour
Minute
12
00
Move
Downloaded From TV-Manual.com Manuals
Return
Adjust
English - 33
Return
Switching the PDP Display On and Off Automatically
You can set the on or off timers so that the PDP Display will:
◆ Switch on automatically and tune source of your choice
at the time you select.
Setup
Time
Language
◆ Switch off automatically at the time you select.
: English
PC
➢
Move
Enter
Return
1
The first step is to set the PDP Display’s clock (refer to
“Setting and Displaying the Current Time” on page 33).
Press the MENU (
Result:
2
Time
12: 00
On Timer
12: 00
Off
Off Timer
12: 00
Off
Move
Enter
Press the ENTER (
4
Press the … or † button to select Time.
Press the ENTER (
) button.
Result:
Return
5
Minute
12
00
6
Component
Volume
Activation
10
No
Move
Adjust
On Timer
Hour
Minute
12
00
Source
Component
Volume
Activation
10
Move
The Time menu is displayed.
The On Timer menu is displayed.
Select Hour, Minute, Source (AV, S-Video, Component, PC1, PC2, or
DVI), or Volume by pressing the œ or √ button.
Set these by pressing the … or † button.
➢
Return
) button.
Press the … or † button to select On Timer.
Press the ENTER (
) button.
Result:
Source
The Setup menu is displayed.
3
On Timer
Hour
The main menu is displayed.
Press the … or † button to select Setup.
Result:
Clock Set
) button.
You can set the hour and minute directly by pressing
the numeric buttons on the remote control.
7
Press the œ or √ button to select Activation.
8
To activate On Timer with the setting entered, select Yes by
pressing the … or † button.
9
Press the ENTER (
Result:
) button.
The Time menu is displayed again.
Yes
Adjust
Return
Continued...
Downloaded From TV-Manual.com
Manuals
English - 34
10
Press the … or † button to select Off Timer.
Press the ENTER (
) button.
Result:
11
The Off Timer menu is displayed.
Select Hour or Minute by pressing the œ or √ button.
Set these by pressing the … or † button.
➢
Setup
Time
Language
You can set the hour and minute directly by pressing
the numeric buttons on the remote control.
Move
12
Press the œ or √ button to select Activation.
13
To activate Off Timer with the setting entered, select Yes by
pressing the … or † button.
14
Press the ENTER (
15
Press the EXIT button to exit.
➢
: English
PC
) button.
Auto Power Off
When you set the timer “On”, the PDP Display will
eventually turn off, if no controls are operated for 3 hours
after the PDP Display was turned on by timer. This function
is only available in timer “On” mode and prevents
overheating, which may occur if a PDP Display is on for
too long.
Enter
Return
Time
Clock Set
12: 00
On Timer
12: 00
Off
Off Timer
12: 00
Off
Move
Enter
Return
Off Timer
Hour
Minute
Activation
12
00
No
Move
Adjust
Return
Off Timer
Hour
Minute
Activation
12
00
Yes
Move
Downloaded From TV-Manual.com Manuals
Adjust
English - 35
Return
Selecting the Fan
Fans inside the PDP Display are used to lower the temperature of the
tops and the front of the PDP Display. To reduce the noise of the fan,
you may stop the fan by setting the Fan to “Off”.
The temperature of the top and the front of the PDP Display may
increase when you watch the PDP Display for a long period of time
while the fan is stopped, but the PDP Display will operate normally.
Function
Screen Burn Protection
Safety Lock
Multi Control
Video Wall
Fan
: Off
1
Move
Enter
Press the MENU (
Result:
Return
) button.
The main menu is displayed.
Press the ▲ or ▼ button to select Function.
2
Result:
Function
The Function menu is displayed.
Screen Burn Protection
Safety Lock
3
Press the ENTER (
4
Press the ▲ or ▼ button to select Fan.
Press the ENTER (
) button.
5
Select Off or On by pressing the ▲ or ▼ button.
Press the ENTER (
) button.
6
Press the EXIT button to exit.
) button.
Multi Control
Video Wall
Fan
: Off
Off
On
Move
Enter
Return
➢
◆ If your PDP Display is displayed vertically, the fan
automatically works.
◆ The message Check Fan is displayed if there is a
fan problem.
◆ Please use the fan when the temperature is over 35
degrees.
The Fan function for the model PPM42M6S is not
displayed.
Downloaded From TV-Manual.com
Manuals
English - 36
Viewing the Picture in Picture (PIP)
You can display a sub picture within the main picture of external A/V
devices. In this way you can PDP Display the video input from any
connected devices while monitoring other video inputs.
Picture
Mode
: Dynamic
Color Control
1
Press the MENU (
: 16:9
PIP
The main menu is displayed.
Result:
2
Size
) button.
Press the … or † button to select Picture.
Move
The Picture menu is displayed.
Result:
3
Press the ENTER (
4
Press the … or † button to select PIP.
) button.
Press the ENTER (
Enter
Return
) button.
PIP
The PIP is selected.
Result:
5
Press the ENTER (
) button again.
To activate, set PIP to On by pressing the … or † button.
) button.
Press the ENTER (
6
Press the … or † button to select Source.
) button.
Press the ENTER (
PIP
: Off
Off
Source
: AV
On
Position
:
Move
Return
PIP
The following options are available.
Result:
Enter
PIP
AV - S-Video
7
Select a source of the sub picture by pressing the … or † button.
) button.
Press the ENTER (
8
Press the … or † button to select Position.
) button.
Press the ENTER (
: On
Source
: AV
Position
:
Move
AV
S-Video
Enter
Return
The following options are available.
-
Result:
PIP
9
10
PIP
Select a position of the sub picture by pressing the … or †
button. Press the ENTER (
) button.
: On
Source
: AV
Position
:
Press the EXIT button to exit.
Easy functions of the remote control.
Move
Buttons
Feature
PIP
Used to activate or deactivate the PIP function directly.
SOURCE
Used to assign a source of the sub picture (AV, S-Video).
Table of PIP Settings
Sub
X - This PIP combination is not available.
O - This PIP combination is available.
AV(CVBS)
S-Video
Component
PC1
PC2
DVI
AV(CVBS)
X
X
X
X
X
X
S-Video
X
X
X
X
X
X
Component
X
X
X
X
X
X
PC1
O
X
X
X
X
X
PC2
O
X
X
X
X
X
DVI
O
O
X
X
X
X
Main
Enter
Downloaded From TV-Manual.com Manuals
English - 37
Return
Viewing an External Signal Source
Once you have connected up your various audio and video
systems, you can view different sources by selecting the
appropriate input.
Input
Source List
: AV
Edit Name
1
Press the MENU (
Result:
Enter
Return
AV
:----
S-Video
:----
Component
:----
PC1
:----
PC2
:----
DVI
:----
Move
Result:
3
Source List
5
Press the … or † button to select the signal source, press the
ENTER (
) button.
Result:
➢
◆ You can also set these options simply by pressing the
SOURCE button on the remote control.
6
Enter
Repeat steps 1 to 3.
7
Press the … or † button to select Edit Name.
Press the ENTER (
) button.
8
Press the … or † button to select external source to be edited.
Press the ENTER (
) button.
Edit Name
Result:
: - - - -----
S-Video
: - - - -VCR
:---DVD
:---D-VHS
:---Cable STB
:----
Component
Return
Select the required device by pressing the … or † button.
Press the ENTER (
) button.
10
Press the EXIT button to exit.
➢
Downloaded From TV-Manual.com
Manuals
English - 38
The available device names are listed.
VCR, DVD, D-VHS, Cable STB, HD STB, Satellite STB,
AV Receiver, DVD Receiver, Game, Camcorder,
DVD Combo, DHR (DVD HDD Recorder),or PC
9
†
Enter
The Input menu is displayed again.
Return
AV
Move
The available signal sources are listed.
: AV
Move
DVI
) button again.
◆ AV, S-Video, Component, PC1, PC2, or DVI
Result:
PC2
The Source List is selected.
Press the ENTER (
Return
Edit Name
PC1
) button.
4
Input
Source List
The Input menu is displayed.
Press the ENTER (
Result:
Enter
The main menu is displayed.
Press the … or † button to select Input.
2
Move
) button.
If you change the external source while viewing, it might
take a short period of time for picture to be switched.
Connecting to the Audio/Video Input
The "AV IN" connectors are used for the equipment with an Composite Video output, such as video
game devices or video disc players.
Rear of the PDP Display
VCR
(Input)
①
DVD
Decoder /
Video game device
Video disc player
The "AV OUT" connectors are used for the equipment with an Composite
Video input, such as a camcorder or VCR.
Camcorder
Rear of the PDP Display
(Output)
Satellite receiver
②
① If you have a second VCR and wish to copy cassettes tape, connect the source VCR to “AV IN” and the
target VCR to “AV OUT” so that you can redirect the signal from “AV IN” to “AV OUT”.
② When you wish to record a programme, connect the receiver to “AV IN” and the VCR to “AV OUT” so that
you can redirect the signal from “AV IN” to “AV OUT”.
➢
☛
Signal is outputted through the AV OUT only when the signal source is AV.
Whenever you connect an audio or video system to your
PDP Display, ensure that all elements are switched off.
Refer to the documentation supplied with your equipment
for detailed connection instructions and associated safety
precautions.
Downloaded From TV-Manual.com Manuals
English - 39
Connecting to the S-Video Input
The S-VIDEO and RCA (AUDIO-L/R) connectors are used for equipment with an S-Video output,
such as a camcorder or VCR.
Rear of the PDP Display
Camcorder
①
and
VCR
① To play picture and sound, both the S-VIDEO and RCA connectors must be used.
Connecting to the Component Input
Rear of the PDP Display
DVD
DTV Receiver
The COMPONENT IN connectors are used for DTV receiver or DVD.
(480i,p/576i,p/720p/1080i)
Downloaded From TV-Manual.com
Manuals
English - 40
Connecting to the DVD/DTV Receiver Input
Rear of the PDP Display
Y / PB / PR
DVD
L/R
Digital Set-Top Box
The “COMPONENT IN” (or “Y/PB/PR” (video) and “AUDIO”) connectors are
used for equipment with a DVD/ DTV Receiver output.
(480i, 576i, 480p, 576p, 720p, 1080i)
Connecting to the DVI Input
The “DVI IN” (video) and “AUDIO” connectors are used for equipment with a DVI output.
Rear of the PDP Display
Personal Computer
and
Downloaded From TV-Manual.com Manuals
English - 41
Connecting to the PC Input
The “PC 1” (or “PC IN2 (BNC)”) and “AUDIO” connectors are used for interfacing with your PC.
Rear of the PDP Display
Personal Computer
or
Only when watching PDP Display in PC1
mode, you can use the RGB OUT port to
connect the current screen to another
PDP in the same mode.
Downloaded From TV-Manual.com
Manuals
English - 42
Setting up Your PC Software (Windows only)
The Windows display-settings for a typical computer are shown below. But the actual screens on your
PC will probably be different, depending upon your particular version of Windows and your particular
video card. But even if your actual screens look different, the same, basic set-up information will apply
in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)
1 Right click the mouse on the Windows Desktop,
then click on Properties.
The Display Properties will be displayed.
2 Click on Settings tab, then set the Display Mode
with reference to the Display Modes Table.
You do not need to change the Colours settings.
3 Click on Advanced. A new settings dialog box
will be displayed.
4 Click on the Monitor tab, then set the Screen
refresh rate with reference to the Display Modes
Table. Set the Vertical Frequency and Horizontal
Frequency individually if you can do so instead of
setting the Screen refresh rate.
2
3
5 Click on OK to close the window, then Click on
OK button to the Display Properties window.
Automatic re-booting may commence at this
moment.
6 Shutdown the PC, and connect it to your PDP
Display. (“Connecting to the PC Input” on page
42)
4
5
Downloaded From TV-Manual.com Manuals
➢
◆ The actual screens on your PC may look
different, depending on your particular
version of Windows and the type of your
PC.
◆ When you use your PDP Display as a PC
monitor, it supports Colours up to 32 bits.
◆ In this case, the display on the PDP Display
may look different depending on your
particular version of Windows or the PC
manufacturer.
◆ When connecting a PC (including the DVI
connection), you must set it to the display
settings that are supported by the PDP
Display. Otherwise, the message Out of
input range will be displayed.
English - 43
Input Mode (PC/DVI)
Both screen position and size will vary depending on the type of PC monitor and its resolution.
The table below shows all of the display modes that are supported:
Resolution
VGA
Vertical
frequency (Hz)
Horizontal
frequency (kHz)
70
85
85
70
85
60
72
75
85
56
60
72
75
85
60
70
75
❉85
60
72
75
❉85
60
75
60
75
60
75
60
60
31.5
37.9
37.9
31.5
37.9
31.5
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
48.4
56.5
60.0
68.7
29.8
35.1
36.0
37.0
31.8
67.5
64.0
80.0
47.7
60.1
47.8
75.0
640 x 350
640 x 400
720 x 400
640 x 480
◆
◆
◆
◆
◆
◆
◆
◆
SVGA
800 x 600
XGA
1024 x 768
WVGA
848 x 480
SXGA
❉852 x 480
❉1152 x 864
❉1280 x 1024
WXGA
❉1280 x 768
UXGA
1360 x 768
❉1600 x 1200
PPM42M6S
✔
✔
✔
✔
✔
✔/
✔
✔
✔
✔
✔/
✔
✔
✔
✔/
✔
✔
✔
✔/
✔
✔
✔
✔/
✔
✔
✔
PPM42M6H
PPM50M6H
✔
✔
✔
✔
✔
✔/
✔
✔
✔
✔
✔/
✔
✔
✔
✔
✔
✔/
✔
❉✔
❉✔
❉✔
✔
✔
✔
✔
✔
✔
✔/
✔
✔
✔
✔
✔/
✔
✔
✔
✔
✔
✔/
✔
❉✔
❉✔
❉✔
✔
✔
✔/
✔
✔
✔
✔
✔/
✔
✔
✔/
✔/
✔
✔
“❉” mode does not work with DVI mode.
The interlace mode is not supported.
The PDP might operate abnormally if a non-standard video format is selected.
The 852 x 480 mode is only supported by a particular video card (PIXEL PERFECT made by IMAGINE
GRAPHICS Ltd.).
In 1360 x 768 resolution, the screen displays 1360 pixels horizontally.
A “✔” mark means that this mode can be supported.
A “ ” mark means that this mode is recommended.
In DVI mode, this product does not support DDC in DTV format (1080i/720p/480p); some of DVD/STBs
supporting DTV format may display the poor picture.
Downloaded From TV-Manual.com
Manuals
English - 44
Power Saver (PC1 mode only)
This PDP Display has a built-in power management system called Power Saver. This power
management system saves energy by switching your PDP Display into a low-power mode when it has
not been used for a certain amount of time. You use a software utility installed on your computer to set
up this feature. See the table below for details.
State
Power-saving Function Mode
Normal
Operation
Horizontal Sync
Active
Active
Power-off Mode
Position A2
Inactive
Vertical Sync
Active
Inactive
Inactive
Video
Active
Blanked
Blanked
Power Indicator
Green On
Green Blinking
Green Blinking
(3 sec Interval)
(3 sec Interval)
◆
◆
◆
◆
Suspend Mode
Position A1
If the horizontal sync is inactive and the vertical sync active, this PDP Display goes to the screen mute state.
This PDP Display automatically returns to normal operation when horizontal and vertical sync return.
This occurs when moving the computer’s mouse or pressing a key on the keyboard.
For energy conservation, turn your PDP Display OFF when it is not needed, or when leaving it unattended for
long periods.
Downloaded From TV-Manual.com Manuals
English - 45
Troubleshooting: Before Contacting Service Personnel
Before contacting Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of the
PDP Display and contact your local dealer.
No sound or picture
◆ Check that the mains lead has been connected to a wall socket.
◆ Check that you have pressed the ON or OFF button on the remote
control.
◆ Check the picture contrast and brightness settings.
◆ Check the volume.
Normal picture but no sound
◆ Check the volume.
◆ Check whether the volume MUTE button on the remote control has
been pressed.
No picture or black and white picture
◆ Adjust the color settings.
◆ Check that the video system selected is correct.
Sound and picture interference
◆ Plug your PDP Display into a different mains socket.
Remote control malfunctions
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check the battery terminals.
Screen is black and power
indicator light blinks steadily.
◆ On your computer check: Power, Signal Cable.
The PDP Display is using its power management system.
Move the computer's mouse or press any key on the keyboard.
Downloaded From TV-Manual.com
Manuals
English - 46
Technical Specifications
Exterior design and product specifications are subject to change without prior notice to improve the
performance of this product.
PPM426S :
This is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures. (Class A product only)
PPM42M6H/50M6H:
This PDP applies to Class B digital device for home use. This PDP has been registered for residential use
in terms of EMI. So it can be used in all areas as well as residential areas.
Dimensions
(W x D x H)
PPM42M6S/PPM42M6H - 1027 x 96.5 x 630.5 mm ; 40.43 x 3.79 x 24.82 inches
PPM50M6H - 1204 x 96.6 x 724.1 mm ; 47.4 x 3.8 x 28.5 inches
Weight
(Without stand)
PPM42M6S - 31.0 kg
PPM42M6H - 35.0 kg
PPM50M6H - 41.0 kg
Screen aspect ratio
16:9
Screen size
PPM42M6S/PPM42M6H - 42 inch
PPM50M6H - 50 inch
Native pixel resolution
(H x V)
PPM42M6S - 852 x 480
PPM42M6H - 1024 x 768
PPM50M6H - 1366 x 768
Color systems
PAL, SECAM, NTSC (NT3.58/NT4.43)
Sound
Stereo, SRS TSXT
Audio output power
10W + 10W (8Ω)
Power supply
U.S.A/Canada - AC110-120V±10%, 60Hz
Other countries - AC100-240V±10%, 50/60Hz
Power consumption
PPM42M6S - 300 Watts
PPM42M6H - 380 Watts
PPM50M6H - 480 Watts
Video inputs
VIDEO IN - AV/S-VIDEO
COMPONENT IN - Y/PB/PR (RCA, 3P, 480i~1080i)
RGB1(PC1) IN - D-SUB, 15P
RGB2(PC2) IN
VGA~UXGA (R/G/B/H/V)
DVI IN - DVI-D type
PDP Display outputs
VIDEO OUT - VIDEO/L/R (RCA, 3P)
Audio inputs
VIDEO IN - L/R
COMPONENT IN - L/R (RCA, 2P)
AUDIO (Stereo jack for RGB1/2(PC1/2) and DVI input, 2 x mini jack)
Audio outputs
EXT SPEAKER (8Ω) - R+/-, L+/-
External control
RS232C - IN/OUT (D-SUB, 9P)
Downloaded From TV-Manual.com Manuals
English - 47
This page is intentionally
left blank.
Downloaded From TV-Manual.com Manuals
This page is intentionally
left blank.
Downloaded From TV-Manual.com Manuals
Downloaded From TV-Manual.com Manuals