Universal Remote Control MX-1200 Owner`s manual

MX-1200 Color Touch Screen
Owner’s Manual
MX-1200 COLOR TOUCH SCREEN
This remote control was Custom Programmed for you by:
For questions about your Custom Programming call:
Custom Programming of a complex home theater and/or a multi-room
system is one of the most challenging tasks within an audio/video
installation. It involves an intimate knowledge of how the components
interact and exact details on the proper sequences of control.
Only a Complete Control dealer has the requisite experience and training
to quickly and effectively customize a remote control for true automated
operation.
Congratulations on your choice!
MX-1200 Owner's Manual © 2012 Universal Remote Control, Inc.
The information in this manual is copyright protected. No part of this manual may be
copied or reproduced in any form without prior written consent from Universal
Remote Control, Inc.
UNIVERSAL REMOTE CONTROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL,
TECHNICAL OR EDITORIAL ERRORS/OMISSIONS MADE IN THIS MANUAL.
The information in this manual may be subject to change without prior notice.
Complete Control is a registered trademark of Universal Remote Control, Inc.
All other brand or product names are trademarks or registered trademarks of their
respective companies or organizations.
500 Mamaroneck Avenue, Harrison, NY 10528
Phone: (914) 835-4484 Fax: (914) 835-4532
MX-1200 COLOR TOUCH SCREEN
Congratulations!
1
Using the MX-1200
2
Connecting the Battery Pack
3
Using the Charging Base
3
Displaying the Settings Screen
4
Sleep Settings
5
System
5
Brightness
5
Power
5
Button Light
6
Date and Time
6
Calibration
6
Pickup Settings
6
Sound
7
Factory Default
7
Exit
7
Maintaining Your MX-1200
8
Specifications
8
USA Limited Warranty Statement
9
Federal Communication Commission
Interference Statement
11
MX-1200 COLOR TOUCH SCREEN
Congratulations
Thank you for purchasing the
Complete Control MX-1200 touch
screen universal remote control.
This remote can wirelessly control
your devices throughout the home
using an RF base station.
Controlling your home is simple
with the MX-1200 remote.
Brilliant 2.4" color touch screen with audible button presses
The MX-1200 has a programmable 2.4” color touch screen. When any
button is pressed, an audible response is heard and the color LCD
screen, as well as the remote buttons, will light up.
Fast setup of complex systems via Complete Control PC Program
To fully automate your audio/video system, the programmer must
have detailed knowledge of each component and how the system is
connected and operated. Only a trained and certified professional
audio/video installer can install an MX-1200 remote control in a
timely and efficient manner.
User interface customizable for any activity
Each button is customizable for activities such as Watch TV or
Listen to Radio. These activities can contain multiple commands
(macros) which enable a single button press to turn the needed
devices ON or OFF.
Ultra-reliable narrow band RF - compatible with URC 418 MHz
RF Base Stations.
The MX-1200 can communicate directly to RF base stations, such
as the MRF-350 and the MRF-260. It also natively communicates to
URC Lighting via 418 MHz RF. This gives the MX-1200 the ability to
control your system without being in direct line-of-sight.
Interchangeable Buttons
The MX-1200 has two interchangeable "hard" buttons. Choose from
any of the supplied buttons to fill these spaces.
Page 1
MX-1200 COLOR TOUCH SCREEN
Using the MX-1200
The MX-1200's main pages display the activities and devices in your system.
Press the MAIN button to view your devices or the activities placed here by
your custom installation specialist. Large systems may have more than one
page. Press either of the PAGE buttons if you don’t see all your devices.
Gently press any screen button with your finger to select an activity or a
device. The screen will change to display the buttons you need for that
activity/device. The PAGE buttons may reveal additional buttons for some
devices and activities.
When you would like to control another device, press the MAIN page
button and select a new device button.
The Main button
always displays
main menu pages.
The Page buttons
display additional
pages of controls.
Use the supplied
buttons to
interchange
these two
“hard” buttons.
The Volume and
Mute buttons are
always available
regardless of what
screen is displayed.
The 5 way cursor
enables you to
navigate through a
variety of on-screen
menus with ease.
Page 2
MX-1200 COLOR TOUCH SCREEN
Connecting the Battery Pack
Unlock the rear cover by pressing down on the spring lock at the
top of the cover. Remove the cover. For shipment from the factory,
the battery is left out of the MX-1200. Place the battery into the
battery compartment, making sure you align the contacts on the
battery to the contacts on the MX-1200. The battery will snap into
place when aligned properly. Replace the cover and snap it into
place.
Using the Charging Base
Plug the 5V adapter into a power outlet and
into the back of the charging base.
Gently place the MX-1200 into the cradle of
the charging base. It automatically aligns itself
to the contacts on the charging base.
The Status light should immediately light. Red
indicates that it is charging. Blue shows that it
is fully charged. There is no harm in leaving
the MX-1200 on its charging base whenever
it is not in use.
Red indicates charging, Blue that
the remote is fully charged.
Page 3
MX-1200 COLOR TOUCH SCREEN
Displaying the Settings Screen
You can enter the Settings menu by pressing and holding the MAIN and
ENT button for three seconds. The MX-1200i will timeout after it is idle for
30 seconds and return to the previous setting or Main screen. There are
two pages of Settings screens. Select a setting by pressing a button on the
LCD screen. Press either of the PAGE buttons to access the other page. To
go back a step or to get out of the settings screen, press the MAIN button.
There are two pages of Settings screen. To access the other page press
either of the PAGE buttons.
Page buttons reveal the
rest of the settings.
Page 4
Page 2 of the Settings
Screen
MX-1200 COLOR TOUCH SCREEN
Sleep Settings
Conserve energy by configuring the MX-1200 to
fall asleep after a specified amount of time. Select
an amount of time by adjusting the slide bar.
System
The System Information screen displays data about
your MX-1200's operating system, memory etc.
Brightness
Adjust the screen brightness by moving the slider.
Min (minimum) is the dimmest setting and Max
(maximum) is the brightest setting.
Power
You can display the remaining charge by selecting
Power. You can also adjust when the low battery
warning screen will appear.
Page 5
MX-1200 COLOR TOUCH SCREEN
Button Light
You can adjust the brightness of the LEDs that
backlight the buttons of the MX-1200. Move the
slider to the left to dim or move it to the right to
brighten the backlighting.
Date and Time
Your MX-1200 may have been programmed to
display the time or date on the touch screen.
If you need to, you can adjust the time displayed
by changing the settings on this screen.
Calibration
If you like, you can calibrate the screen by running
the calibration setting. You will need a pen top or
PDA stylus to do this. Do not attempt to calibrate
using your fingers.
Pickup Settings
You can set your MX-1200 to only turn on when
touched, or every time you move it. Adjust the
Pickup Sensor Level by sliding the bar to the
desired percentage.
Page 6
MX-1200 COLOR TOUCH SCREEN
Sound
You can adjust the button beep to Off or Loudest by
dragging the slider to your desired position.
Factory Default
WARNING! Only use this button when instructed
to by Technical Support. It resets the memory of
the MX-1200 to the factory condition. All your
programming will be lost!
Exit
When you have finished adjusting Settings, simply tap the Exit button to
return to normal operation.
Page 7
MX-1200 COLOR TOUCH SCREEN
Maintaining Your MX-1200
Be careful not to scratch the touch screen, only use your finger to tap
the LCD touch screen or use a plastic pen top or PDA stylus. Never use
a real pen, pencil or any other sharp object on the screen. Keep it away
from extreme cold or heat. The MX-1200 is not waterproof. Do not use
it in any location that is damp or wet. If you spill water on it, take out
the battery pack and let the MX-1200 dry for 48 hours before powering
it up again. If you spill coffee or another beverage on it, clean it with
distilled water. Make sure no water gets inside the MX-1200. The touch
screen contains a glass element. Don’t drop the MX-1200 or impact it
against anything.
Use a soft, damp cloth to clean the screen. If the screen still shows
finger prints, clean it with watered down window-cleaner. Do not use
anything abrasive and don’t use too much water, some might leak into
the interior.
Precautions & Information: Rechargeable Lithium Ion Batteries
If you will not be using your remote control for an extended period of
time, be sure to remove the battery. Do not attempt to disassemble,
alter or apply heat to the battery. Use care to avoid dropping the
battery or subjecting it to severe impact that could damage the case.
The battery should not be immersed in water. Lithium Ion batteries are
recyclable. For the address of a recycle drop-off location near you call
toll free 1-800-822-8837 or visit http://www.rbrc.com
Specifications
CPU : ARM 32-bit Cortex-M3 (72MHz)
Memory : 8Mbit SRAM, 64Mbit Flash
Customization Capability : Up to 200 devices and up to 10 pages each for a
total of 2000 pages.
Learning Capability : Standard frequencies (15kHz to 460kHz)
Macro Capability : Up to 255 steps each
IR Range (Line of Sight via Infrared) : 30-50 feet, depending on the environment
RF Range (radio frequency) : 50 to 100 feet, depending upon the environment
RF Frequency : 418 MHz
Weight : 5.73 ounces (with battery loaded)
Size : 8.46”H x1.97”W x 1.02” D
Battery : Lithium Ion rechargeable battery included
Page 8
MX-1200 COLOR TOUCH SCREEN
USA Limited Warranty Statement
Your Universal Remote Control, when delivered to you in new condition,
is warranted against defects in materials or workmanship as follows:
UNIVERSAL REMOTE CONTROL, INC. warrants this product against
defects in material or workmanship for a period of one (1) year and as set
forth below. Universal Remote Control will, at its sole option, repair the
product using new or comparable rebuilt parts, or exchange the product
for a comparable new or rebuilt product. In the event of a defect, these
are your exclusive remedies.
This Limited Warranty covers only the hardware components packaged
with the Product. It does not cover technical assistance for hardware or
software usage and it does not cover any software products whether or
not contained in the Product; any such software is provided "AS IS" unless
expressly provided for in any enclosed software Limited Warranty.
To obtain warranty service, you must deliver the product, freight prepaid,
in its original packaging or packaging affording adequate protection to
Universal Remote Control at the address provided in the Owner's Manual.
It is your responsibility to backup any macro programming, artwork,
software or other materials that may have been programmed into your
unit. It is likely that such data, software, or other materials will be lost
during service and Universal Remote Control will not be responsible for
any such damage or loss. A dated purchase receipt, Bill of Sale, Installation
Contract or other verifiable Proof of Purchase is required. For product
support and other important information visit Universal Remote Control's
website: http://www.UniversalRemote.com or call the Customer Service
Center (914) 835-4484.
This Limited Warranty only covers product issues caused by defects
in material or workmanship during ordinary consumer use. It does
not cover product issues caused by any other reason, including but
not limited to product issues due to commercial use, acts of God, thirdparty installation, misuse, limitations of technology, or modification of
or to any part of the Universal Remote Control product. This Limited
Warranty does not cover Universal Remote Control products sold
as USED, AS IS, REFURBISHED, so-called “B STOCK” or consumables
(such as batteries). This Limited Warranty is invalid if the factory-applied
serial number has been altered or removed from the product. This Limited
Warranty is valid only in the United States of America. This Limited
Warranty specifically excludes products sold by unauthorized resellers.
Page 9
MX-1200 COLOR TOUCH SCREEN
LIMITATION OF REMEDIES
UNIVERSAL REMOTE CONTROL SHALL NOT BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF
ANY EXPRESS OR IMPLIED WARRANTY OR CONDITION ON THIS
PRODUCT. IN NO EVENT SHALL UNIVERSAL REMOTE CONTROL
BE LIABLE, WHETHER IN CONTRACT OR IN TORT (INCLUDING
NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE PURCHASE
PRICE OF THE PRODUCT, ACCESSORY OR SOFTWARE, OR FOR
ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS,
LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR OTHER FINANCIAL LOSS ARISING
OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY
TO USE THE PRODUCTS, ACCESSORIES OR SOFTWARE TO THE
FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, THERE
IS NO OTHER WARRANTY EXPRESSED OR IMPLIED. UNIVERSAL
REMOTE CONTROL WILL NOT BE HELD RESPONSIBLE FOR STATEMENTS MADE BY OTHERS CONCERNING THE MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT.
Some states or jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, or allow limitations on how
long an implied warranty lasts, so the above limitations or exclusions
may not apply to you. This Limited Warranty gives you specific legal
rights and you may have other rights which vary from state to state or
jurisdiction to jurisdiction.
REV020708
Page 10
MX-1200 COLOR TOUCH SCREEN
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
Warning!
Changes or modifications not expressly approved by the manufacturer could
void the user's authority to operate the equipment.
Note : The manufacturer is not responsible for any Radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user's authority to operate the equipment.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the authority to operate equipment.
Page 11
NOTE
Page 12
NOTE
Page 13
NOTE
Page 14
NOTE
Page 15
500 Mamaroneck Avenue, Harrison, NY 10528
Phone: (914) 835-4484 Fax: (914) 835-4532
www.universalremote.com
OCE-0113A Rev 03