Venstar TSTATEZ Owner`s manual

residential
THERMOSTAT
EasyStat
TSTATEZ
Single Day
world’s easiest
PROGRAMMABLE THERMOSTAT
PROGRAMMABLE THERMOSTAT
PROGRAMMABLE
up to 2-heat
& 2-cool
One for All - Can Control:
- Gas / Electric
- Heat Pump
- Electric Heat
- Hydronic Systems
Non-Volatile Memory - Retains settings
in the event of a power failure
Outdoor Sensor Ready HEAT
Compatible with the
HEAT
COOL
PUMP
optional wired, or wireless
Outdoor Sensor
Use with most Air Conditioning & Heating Systems including: 1 or 2 Stage
Electric Cooling & 2 Stage Gas Heating, Heat Pump, Electric or Hydronic Heat.
INSTALLATION
INSTRUCTIONS
Venstar Inc. 08/07
Table Of Contents
Step #1: Preparation
2
Step #2: Remove & Replace
Old Thermostat
3
Step #3: Wire Connections
4
Sample Wiring Diagrams
5
Step #4: Test Operation
9
Trouble Shooting
10
CAUTION
Follow Installation Instructions carefully.
DISCONNECT POWER TO THE HEATER AIR CONDITIONER BEFORE REMOVING
THE OLD THERMOSTAT AND INSTALLING
THE NEW THERMOSTAT.
WARNING
Venstar Inc. 08/07
P/N TSTAT1100EZ
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Page 1
STEP #1
i2:00
WAKE
74 72
i2:00
WAKE
Pm
HEAT
74 72
Pm
HEAT
Proper installation of the thermostat will be
accomplished by following these step
by step instructions. If you are unsure
about any of these steps, call a qualified
technician for assistance.
These tools will be required:
Flat Blade
Screwdriver
i2:00
WAKE
74 72
i2:00
WAKE
HEAT
74 72
i2:00
WAKE
Pm
Pm
HEAT
74 72
Pm
HEAT
PREPARATION
Wire cutter
& Stripper
Make sure your Heater/Air Conditioner
is working properly before beginning
installation of the thermostat.
Carefully unpack the thermostat.
Save the screws and instructions.
Turn off the power to the Heating/Air
Conditioning system at the main fuse
panel. Most residential systems have
a separate breaker for disconnecting
power to the furnace.
Page 2
STEP #2
i2:00
WAKE
74 72
i2:00
WAKE
Pm
HEAT
74 72
i2:00
WAKE
HEAT
74 72
i2:00
WAKE
Pm
Pm
HEAT
74 72
Pm
HEAT
REMOVE & REPLACE OLD THERMOSTAT
Remove the cover of the old thermostat.
If it does not come off easily check for
screws.
Loosen the screws holding the thermostat
base or subbase to the wall, and lift away.
Disconnect the wires from the old
thermostat. Tape the ends of the wires
as you disconnect them, and mark them
with the letter of the terminal for easy
reconnection to the new thermostat.
Keep the old thermostat for reference
purposes, until your new thermostat is
functioning properly.
Page 3
WIRE CONNECTIONS
STEP #3
i2:00
WAKE
74 72
Pm
HEAT
If the terminal designations on your old
thermostat do not match those on the
new thermostat, refer to the chart below,
or the wiring diagrams that follow.
Wire from the
old thermostat
terminal marked
Function
Install on the
new thermostat
connector marked
G
G or F
Fan
Y1, Y or C
Cooling
W1, W or H
Heating
Y1
W1,O,B
Rh, R, M, Vr, A
Power
C
Common
C*
R
O/B
Rev. Valve
W1,O,B**
Y2
2nd Stage Cool
Y2
W2
2nd Stage Heat
W2
RS+5
Remote Sensor +5vdc
RS+5
RS
Remote Sensor Signal
RS
Remote Sensor Ground
GND
RS G
* C may not be used on all systems.
** O/B is used if your system is a Heat Pump.
Page 4
Sample Wiring Diagrams
5 Wire, 1 Stage Cooling, 1 Stage Gas Heat
O
W2 Y2 R W1 Y1 G
Residential Gas or Electric Heat *,
Electric Cool, split systems & package
units
C
Thermostat
L
E
24 vac common
C
fan relay
compressor relay
G
Y1
O
1st stage heat circuit
24 vac return
W1
R
Y2
W2
4 Wire, 1 Stage Cooling, 1 Stage Gas Heat
O
W2 Y2 R W1 Y1 G
Residential Gas or Electric Heat *,
Electric Cool, split systems & package
units
C
Thermostat
L
E
C
fan relay
compressor relay
G
Y1
O
1st stage heat circuit
24 vac return
W1
R
Y2
W2
* If using electric heat this option must be
selected on during advanced setup.
Page 5
Sample Wiring Diagrams
6 Wire, 2 Stage Cooling, 1 Stage Heat
O
W2 Y2 R W1 Y1 G
Residential 2 Stage Cooling, with
Gas or Electric Heat*
C
Thermostat
L
E
24 vac common
C
fan relay
compressor relay
Y1
G
O
1st stage heat circuit
24 vac return
2nd stage compressor relay
W1
R
Y2
W2
6 Wire, 1 Stage Cooling, 2 Stage Heat
O
W2 Y2 R W1 Y1 G
Residential & Commercial 1 Stage Cooling,
with 2 Stage Gas or Electric Heat*
C
Thermostat
L
E
24 vac common
C
fan relay
compressor relay
Y1
G
O
1st stage heat circuit
24 vac return
W1
R
Y2
2nd stage heat circuit
* If using electric heat this option must be
selected on during advanced setup.
Page 6
W2
Sample Wiring Diagrams
7 Wire, 2 Stage Cooling, 2 Stage Heat
O
W2 Y2 R W1 Y1 G
Commercial Gas or Electric Heat *,
Electric Cool, split systems & package units
including Commercial Heat Pumps **
C
Thermostat
L
E
24 vac common
C
fan relay
compressor relay
Y1
G
O
1st stage heat circuit
24 vac return
2nd stage compressor relay
2nd stage heat circuit
* If using electric heat, this option must ** Commercial Heat Pumps do not have
the heat pump turned on in advanced setup.
be selected on during advanced setup.
W1
R
Y2
W2
5 Wire, 1 Stage Cooling, 1 Stage Heat - Heat Pump***
O
W2 Y2 R W1 Y1 G
No auxiliary heat,
Residential Heat Pumps ,
C
Thermostat split systems & package units
L
E
24 vac common
C
fan relay
compressor relay
G
Y1
reversing valve
O
W1
24 vac return
*** If using Residential Heat Pump, this option
must be selected on during advanced setup.
R
Y2
W2
Page 7
Sample Wiring Diagram
6 Wire, 1 Stage Cooling, 2 Stage Heat, Heat Pump *
O
W2 Y2 R W1 Y1 G
C
Most residential split and package heat pumps
with auxiliary heat
Thermostat
L
E
24 vac common
C
fan relay
compressor relay
Y1
1st stage heat circuit
G
O
W1
24 vac return
R
Y2
2nd stage heat circuit
* The heat pump option must be selected
on during advanced setup.
Page 8
W2
STEP #4
i2:00
WAKE
74 72
i2:00
WAKE
Pm
HEAT
74 72
Pm
HEAT
TEST OPERATION
Turn the power on to the Heating/Air
Conditioning system.
On the thermostat, press the MODE/NEXT
button repeatedly until the HEAT icon
appears on the display. Press the UP or
DOWN button until the set temperature is 10
degrees above room temperature. The
HVAC unit should energize in the heating
mode. Note: You may need to wait up to five
minutes for heating to energize due to the
compressor lockout feature.
i2:00
WAKE
74 72
Pm
HEAT
On the thermostat, press the MODE/NEXT
button repeatedly until the COOL icon
appears on the display. Press the UP or
DOWN button until the set temperature is 10
degrees below room temperature. The
HVAC unit should energize in the cooling
mode. Note: You may need to wait up to five
minutes for cooling to energize due to the
compressor lockout feature.
i2:00
WAKE
74 72
Pm
HEAT
Press the UP button until the setpoint is
equal to the room temperature. Press
the FAN button to Fan On. The fan should
turn on and run continuously.
Page 9
TROUBLESHOOTING
i2:00
WAKE
74 72
Pm
HEAT
SYMPTOM: When using 4 wires (R, G, W, Y),
the air conditioning equipment tries
repeatedly to turn on, but cannot. At
times the display dims or disappears.
CAUSE: There is not enough power available
to "power share".
REMEDY: Connect a 270 ohm, 10 watt power
resistor at the furnace as shown below.
For Problem A/C
R
G
W
Y
C
R
TR300-10w
i2:00
WAKE
74 72
i2:00
WAKE
Pm
HEAT
74 72
Pm
HEAT
For Problem Heat
G
W
Y
C
TR300-10w
SYMPTOM: The air conditioning does not
attempt to turn on.
CAUSE: The compressor timer lockout may
prevent the air conditioner from
turning on, for a period of time.
REMEDY: See page 10 of the Owner's Manual
and configure step 8 to defeat the 5minute compressor lockout.
SYMPTOM: The display is blank.
CAUSE: Lack of proper power.
REMEDY: Make sure power is turned on to
the furnace and there are 24vac
between R & W. If C is used, there
needs to be 24vac between R & C.
Page 10
TROUBLESHOOTING
i2:00
WAKE
74 72
i2:00
WAKE
Pm
HEAT
74 72
Pm
HEAT
SYMPTOM: When controlling a Residential Heat
Pump, cooling energizes with a demand for
heat.
CAUSE: Heat pump is not selected "YES" in the
Advanced Setup.
REMEDY: See page 9 of the Owner's Manual
and configure step 4 to enable heat pump
operation.
SYMPTOM: When calling for cooling, both
the heat and cool come on.
CAUSE: The thermostat is configured to
control a heat pump and the HVAC
system is a "conventional" (non-heat
pump) system.
REMEDY: See page 9 of the Owner's Manual
and set step 4 to "NO” to enable gas
electric operation.
Slimline
TSTAT1100EZ
c
FC
Tested to Comply
with FCC Standards
FOR HOME OR OFFICE USE
4Z95
P/N 88-612
Rev. 1
Page 11