Mircom TX3 Series Installation manual

TX3 Series
Touch Screen
Installation Manual
Version 1.3
LT-996
Mircom
Copyright 2012
1 (53)
Copyright 2012 Mircom Inc.
All rights reserved.
Mircom Touch Screen Installation Guide v.1.3 for Windows 2000/NT/XP®.
This manual, as well as the software described in it, is provided under licence or other agreements
and may be used or copied only in accordance with the terms of such license. The content of this
manual is furnished for informational use only. It is subject to change without notice, and should not
be construed as a commitment by Mircom. Mircom assumes no responsibility or liability for any errors
or inaccuracies that appear in this book.
Except as permitted by such license, no part of this publication may be reproduced, stored in a
retrieval system, transmitted in any form by means electronic, mechanical, using any recorded
media, or any other format without the prior written permission of Mircom.
Microsoft, MS-DOS, Windows, and Windows 2000/NT/XP are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.
Mircom
25 Interchange Way
Vaughan, Ontario
L4K 5W3
905.660.4655
Fax:905.660.4113
2 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Contents
1
Introduction 7
1.1
1.2
1.3
1.4
1.5
1.6
1.7
TX3 Systems 8
Features 8
Touch Screen Enclosures 9
Touch Screen Accessories 10
Warranty and Special Notices 10
About This Manual 10
Contact Us 11
2
Enclosure Installation 13
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
Installing the Enclosures and Touch Screen 14
Installing the Kiosk 14
Installing the Surface Mount Enclosure 16
Installing the Touch Screen Panel 17
Installing the Speakers 18
Installing the Frame and Door 20
Installing the Flush Mount Enclosure 21
Installing the Power Supply Enclosure 22
3
Touch Screen System and Setup 25
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
Touch Screen System 26
Touch Screen Main Panel 28
Controller Boards 29
Grounding the Touch Screen 32
Connecting to the External Power Supply 32
Installing the Postal Lock 34
Installing the Telephone Lines 34
Installing Optional Components 34
Verifying Installed Components 35
Beginning Configuration 36
4
Adding Controllers 37
4.1
Adding a Controller 38
5
Appendix 39
5.1
Specifications 40
6
Resident Operating Instructions 43
6.1
6.2
NSL Resident Operating Instructions 44
ADC Resident Operating Instructions 46
Version 1.3
LT-996
TX3 Touch Screen Installation Manual
Copyright 2012
3 (53)
4 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
List of Figures
Figure 1.
Touch Screen Kiosk Base Plate 15
Figure 2.
Touch Screen Surface Mount 16
Figure 3.
Touch Screen Panel 17
Figure 4.
Touch Screen Backbox 18
Figure 5.
Touch Screen Speakers 19
Figure 6.
Touch Screen Frame and Door 21
Figure 7.
Flush Mount Enclosure 21
Figure 8.
Inside the Switching Power Supply Box 23
Figure 9.
Power Supply Voltage Selection Switch 23
Figure 10.
Touch Screen Power Supply Enclosure 24
Figure 11.
Single Touch Screen 27
Figure 12.
Single Touch Screen with ADC and NSL Lines 28
Figure 13.
Touch Screen Panel Components 29
Figure 14.
Touch Screen Controller Board Panel 30
Figure 15.
Controller Board Connectors - Top 31
Figure 16.
Controller Board Connectors - Bottom 32
Figure 17.
MD-990 Terminal Block Wiring 33
Figure 18.
Connecting additional RS-485 Terminal Connector to the First or Last Node of
Network 35
Version 1.3
LT-996
TX3 Touch Screen Installation Manual
Copyright 2012
5 (53)
6 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
1
Introduction
This manual provides information about the installation and operation of the
Touch Screen, and must be read in its entirety before beginning any installation
work.
Installation must be performed by a qualified technician and must adhere to the
standards and special notices set by the local regulatory bodies.
Note:
Mircom periodically updates panel firmware and Configurator
Software to add features and correct any minor inconsistencies.
For information about the latest firmware or software visit the
Mircom website at www.mircom.com.
For warranty and special notices information see the Warranty and Special
Notices chapter on page 47.
Warning:
The Touch Screen assembly must be grounded by a qualified
electrician. An improperly grounded unit can result in
equipment malfunction and electrical shock.
This manual explains
Version 1.3
LT-996
•
Touch Screen System
•
Installation and Setup
•
TX3 Integration
•
Resident Operating Instructions
TX3 Touch Screen Installation Manual
Copyright 2012
7 (53)
Introduction
1.1
TX3 Systems
The Mircom's TX3 series of Touch Screens provide high quality two-way
communication between residents and their visitors in a multi-unit dwelling
establishment.
The basic TX3 system consists of the TX3 Touch Screen and depending on the
application, may be integrated with a combination of Mircom Telephone Access
and Card Access Units. All access systems may be networked together using an
peer-to-peer RS-485 connection.
The TX3 system is capable of providing ADC or NSL type telephone access
control from a single panel or from a networked system.
A maximum of 63 units are supported with any combination of Touch Screens,
Elevator Restriction Units and Card Access Units. Valid network addresses
range from 1 to 63. Units with a real time clock, such as Touch Screens and Card
Access Units, require the address node to be 1.
The access system can be configured as an autodialer controller (ADC) or as a no
subscriber line (NSL) system. Both system setups can be configured for multiple
entrances with independent doors and control devices such as electric door locks,
cameras, and garage doors.
1.1.1
ADC and NSL Capability
TX3 supports full ADC and NSL telephone connectivity from a single Touch
Screen panel or from a networked system. A single panel supports up to five
ADC and/or NSL telephone lines.
1.1.2
Elevator Restriction Units
The TX3-ER-8 Elevator Restriction Unit limits building accessibility by
granting visitor access only to the destination floor.
1.1.3
Other Controllers
Mircom controllers, such as the Telephone and Card Access controllers, may be
networked with the TX3 through a peer-to-peer RS-485 network.
1.2
Features
Features of the TX3 series include:
8 (53)
•
Stainless steel front panel
•
Universal Series enclosure with a built-in rain hood
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Introduction
1.3
•
Large scrolling 8 x 20 LCD display that eliminates the need for an external
directory
•
Back-lit 16 digit keypad with dedicated operational buttons for Page Up,
Page Down, Call and Info
•
Provisions for postal lock and camera
•
Multilingual Display and Voice Greeting (English, French-Canadian and
Spanish) that provides instructions on how to use the Touch Screen
•
Concierge/Security Desk/Guard Phone capability
•
Card Access Interface
•
Supports both Auto Dialer (ADC) and NSL (no phone bill)
•
Ability to network panels together (peer-to-peer)
•
Hands free, full duplex communication
•
Flexible one to four digit resident dial codes
•
Dials up to 18 digit telephone numbers
•
System can be configured locally using the keypad or a computer with the
TX3 configuration software
•
Upload/download configuration files without taking the whole system offline
•
Programming from one location
•
Records a maximum of 5000 event logs
•
Elevator restriction capability
•
Schedule based call restrictions provide more security and flexibility
•
Capability of one person testing the NSL controller without using the
Touch Screen
•
Industry Canada and F.C.C. approved
Touch Screen Enclosures
There are three sizes of enclosures for Touch Screens for the 15 inch and 21 inch
models.
1.3.1
15 Inch Models
The 15 inch Touch Screen models are stand alone, surface or flush mounted.
TX3-TOUCH-K15. 15 inch Touch Screen kiosk stainless steel finish Touch
Screen with speaker, microswitch for postal lock and a PS-4P transformer plug.
Designed for indoor use.
Version 1.3
LT-996
TX3 Touch Screen Installation Manual
Copyright 2012
9 (53)
Introduction
TX3-TOUCH-F15. 15 inch Touch Screen flush mount, stainless steel finish
Touch Screen with speaker, microswitch for postal lock, flush mounting back
box and a PS-4P transformer plug. Designed for indoor use.
TX3-TOUCH-S15. 15” Touch Screen surface mount, stainless steel finish
Touch Screen with speaker, microswitch for postal lock, flush mounting back
box and a PS-4P transformer plug. Designed for indoor use.
1.4
Touch Screen Accessories
The Touch Screen accessories consist of the following items:
1.5
•
CAM-2 TX3 Camera
•
TX3-MDM Modem Module
•
TX3-GPM Guard Phone Module
•
Postal Lock
•
TX3-USB-AD Kit
Warranty and Special Notices
Mircom values your business and always attempts to provide you with the very
best service.
Please see the Warranty and Special Notices chapter on page 47 for information
about the warranty and special notices about equipment use.
1.6
About This Manual
This manual provides comprehensive information on the installation and
configuration of the TX3 Series Touch Screen by the installation technician.
Tasks are described in the order that they are likely to be performed.
This manual applies to the following models:
10 (53)
•
TX3-TOUCH-K15
•
TX3-TOUCH-F15
•
TX3-TOUCH-S15
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Introduction
1.6.1
Version Control
The version number appears on the front cover and changes whenever there is a
major or minor update to any part of the system regarding operation or
configuration.
The following convention indicates major or minor changes:
Initial release. Version 1.00.0
Major change. Version 2.00.0
Minor change. Version 2.01.0
Pre-release changes. Version 2.01.1
1.6.2
Additional Documentation
For additional documentation, see the following Mircom literature:
1.7
•
TX3-CX Touch Screen Administrators Guide LT-995
•
TX3-Telephone Access System Installation and Operation Manual LT969
•
TX3-CX Card Access System Installation and Operation Manual LT-980
•
TX3 Touch Screen User’s Guide LT-968
•
TX3 Two Door Card Access System Kit Catalogue Number 6531
•
TX3 Series Elevator Restriction Accessories Catalogue Number 6532
Contact Us
Mircom fosters a collaborative support process and environment in providing
early feedback to meet your specific needs.
You can contact us from Monday to Friday 8:00 A.M. to 5:00 P.M. E.S.T.
Version 1.3
LT-996
TX3 Touch Screen Installation Manual
Copyright 2012
11 (53)
Introduction
1.7.1
General Inquiries
For general inquiries call us at the following numbers:
Toll Free: 1-888-660-4655
Local: 905-660-4655
1.7.2
Customer Service
Customer service is available at the following numbers:
Toll Free: 1-888-MIRCOM5
Local: 905-695-3535
Local Fax: 905-660-4113
Toll-Free Fax: 1-888-660-4113
1.7.3
Website
Visit the Mircom website, at www.mircom.com, to find the product information
you are looking for and to learn about troubleshooting, training and technical
support options.
The website provides avenues for customers to ask questions about new and
existing technologies, and receive expert technical support about software and
products. Visit www.mircom.com/chat.
1.7.4
Email
As a customer you quickly become informed on how we can help with new
products and technologies. Contact Mircom at mail@mircom.com.
1.7.5
Technical Support
For technical support contact Mircom’s Technical Support Department between 8
A.M. and 5 P.M. (EST) Monday through Friday, excluding holidays.
Toll Free: 1-888-MIRCOM5
Local: 905-695-3535
Local Phone: 905-660-4655
Toll Free Phone: 1-888-660-4655
Email: techsupport@mircom.com
12 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
2
Enclosure Installation
This chapter provides information on how to install the various enclosures and
pre-assembled components.
This chapter explains
Version 1.3
LT-996
•
Kiosk installation
•
Surface Mount installation
•
Flush Mount installation
TX3 Touch Screen Installation Manual
Copyright 2012
13 (53)
Enclosure Installation
2.1
Installing the Enclosures and Touch Screen
The Touch Screen Kiosk, Surface Mount and Flush Mounts units consist of the
following pre-assembled components:
Kiosk. The kiosk is a pedestal mounted Touch Screen TX3-TOUCH-K15 unit
and consists of the following components:
•
Touch Screen Base Plate
•
Touch Screen Kiosk
•
Touch Screen Panel
•
Touch Screen Speakers
•
Touch Screen Frame
•
Touch Screen Door
Surface Mount. The surface mount unit is a Touch Screen TX3-TOUCH-S15
unit and consists of the following components:
•
Touch Screen Enclosure
•
Touch Screen Panel
•
Touch Screen Speakers
•
Touch Screen Frame
•
Touch Screen Door
Flush Mount. The surface mount unit is a Touch Screen TX3-TOUCH-F15 unit
and consists of the following components:
2.2
•
Touch Screen Enclosure
•
Touch Screen Panel
•
Touch Screen Speakers
•
Touch Screen Frame
•
Touch Screen Door
Installing the Kiosk
The Kiosk mounts to the floor inside the building near the entrance, close to the
power source and telephone infrastructure. Access for the power and
communication cables is provided through a cutout in the base plate.
The Kiosk base plate is secured to the floor and the Kiosk is secured to the base
plate as shown in Figure 1.
14 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Enclosure Installation
Kiosk Base Plate
Front
Base Plate
Mounting
Holes (x4)
Kiosk
Mounting
Holes (x12)
Cutout
Figure 1. Touch Screen Kiosk Base Plate
To install the Touch Screen Kiosk base plate
1.
Find a suitable location for the Kiosk next to building entrance and above
the building electrical and communications conduit.
2.
Using the Kiosk base plate as a template, trace an opening in the floor for
the cutout and mark the Touch Screen mounting hole locations as shown in
Figure 1. Ensure that the base plate is aligned with the electrical conduit.
3.
Cut an opening in the floor for the electrical and communications cables.
4.
Secure the base plate to the floor using the supplied 18 screws as shown in
Figure 1.
To install the Touch Screen Kiosk
Version 1.3
LT-996
1.
Slide and latch the Kiosk base into position over the base plate.
2.
Secure the Kiosk onto the front base plate using the supplied six screws
into the locations shown in Figure 1.
3.
Open the Kiosk and secure the Kiosk into the base plate using the supplied
12 screws into the locations shown in Figure 1.
TX3 Touch Screen Installation Manual
Copyright 2012
15 (53)
Enclosure Installation
4.
2.3
Run the wires through the Kiosk opening and proceed with the wiring
installation described in Chapter 3.
Installing the Surface Mount Enclosure
The surface mount enclosure mounts on the wall as shown in Figure 2.
Figure 2. Touch Screen Surface Mount
To surface mount the enclosure
16 (53)
1.
Find a suitable location for the surface mount enclosure over a wall stud.
2.
Using the surface mount enclosure as a template, mark the back mounting
hole locations as indicated in Figure 2. Ensure that at least one side is over
a wall stud.
3.
Remove the enclosure and place the top two screws halfway into the
marked hole locations and wall stud using the supplied screws.
4.
Place the surface mount enclosure onto the two screws.
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Enclosure Installation
5.
Screw the two screws of the surface mount enclosure halfway into the
wall.
6.
Tighten all six screws into place.
Note:
2.4
The enclosure can also be mounted directly onto the drywall using
anchors.
Installing the Touch Screen Panel
The Touch Screen panel attaches directly to the enclosure as shown in Figure 3
(for clarity the Touch Screen and controller boards are not shown).
Figure 3. Touch Screen Panel
To install the Touch Screen panel
1.
Version 1.3
LT-996
Insert the Touch Screen panel inside the enclosure and secure using the
supplied six screws as shown in Figure 3.
TX3 Touch Screen Installation Manual
Copyright 2012
17 (53)
Enclosure Installation
2.5
Installing the Speakers
The speaker assembly consists of a back box and speaker housing, and attaches
directly to the enclosure below the Touch Screen panel as shown in Figure 4.
Figure 4. Touch Screen Backbox
18 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Enclosure Installation
Figure 5. Touch Screen Speakers
To install the speakers
Version 1.3
LT-996
1.
Secure the speaker backbox onto the enclosure using the supplied six
screws as shown in Figure 4.
2.
Run the speaker wires through the opening at the top of the backbox.
3.
Secure the speaker cabinet into the backbox using the supplied six screws
as shown in Figure 5.
TX3 Touch Screen Installation Manual
Copyright 2012
19 (53)
Enclosure Installation
2.6
Installing the Frame and Door
The frame mounts directly to the enclosure and the door attaches directly to the
frame as shown in Figure 6.
To install the frame and door
20 (53)
1.
Secure the frame onto the enclosure using the supplied ten screws as
shown in Figure 6.
2.
Insert the Touch Screen door into the frame and lock into position as
shown in Figure 6.
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Enclosure Installation
Figure 6. Touch Screen Frame and Door
2.7
Installing the Flush Mount Enclosure
The flush mount enclosure mounts directly inside the wall to the wall stud or
supporting structure as shown in Figure 7. Mount the enclosure flush with the
wall and right-side up (the knock out is at the bottom).
Wall
Enclosure
Frame
Top
Enclosure
Front
GROUND
SCREW
LOCATION
Side View
Figure 7. Flush Mount Enclosure
To install the flush mount enclosure
Version 1.3
LT-996
1.
Find a suitable location for the flush mount enclosure beside a wall stud.
2.
Using the enclosure as a template, trace an opening in the wall for the cut
out with one side aligned with the side of the wall stud.
TX3 Touch Screen Installation Manual
Copyright 2012
21 (53)
Enclosure Installation
2.8
3.
Cut an opening in the wall 0.1 inch larger than the trace ensuring that one
side is aligned with the wall stud or supporting structure.
4.
Insert the enclosure into the wall cutout and using the side of the enclosure
as a template mark the side mounting hole location as shown in the side
view in Figure 7. Ensure that at least one side is beside a wall stud.
5.
Remove the enclosure and place the screw halfway into the wall into the
marked hole location using the supplied screw.
6.
Place the enclosure onto the top screw.
7.
Screw the lower two screw at the bottom of the enclosure halfway into the
wall.
8.
Tighten the two screws into place.
9.
Insert the Touch Screen panel inside the enclosure and secure using the
supplied eight screws as shown in Figure 7.
10.
Install the Touch Screen panel, speakers, frame and door as described in
paragraphs 2.4 to 2.6.
Installing the Power Supply Enclosure
The Touch Screen external power supply is an MD-990 156 W, 24 V single
output switching power supply encased inside a metal enclosure. A voltage
selectable switch is located on the side of the power supply and is factory set to
120V but can be switched to 230V.
To set the voltage on the Switching Power Supply
1.
Ensure that the the TX3 unit is off and that all power is disconnected.
Note:
2.
22 (53)
The power must be turned off before the Switching Power Supply is
accessed. Failure to due so may result in damage to the equipment or
electric shock that can lead to death.
Open the Switching Power Supply box using the key for the TX3 unit. The
Switching Power Supply unit is secured inside the box by metal guides and
two screws on either side of the terminal block. Unscrew and remove the
screws on both sides of the terminal block.
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Enclosure Installation
V+
V+
VVN
L
Figure 8. Inside the Switching Power Supply Box
Lift the Switching Power Supply unit out of its box to access the red
voltage selection switch.
4.
Switch the voltage selection switch to the required voltage level. Place a
flathead screwdriver in between one of the holes in the chassis to access the
switch. By default it is set to 115 Volts.
230V
3.
Figure 9. Power Supply Voltage Selection Switch
5.
Place the Switching Power Supply back into the box using the metal
guides to position it and then replace the screws on both sides of the
terminal block to secure it into the box.
6.
Reconnect the power.
The external MD-990 power supply connects to the building power AC power
supply. It is recommended that the unit is powered by its own dedicated electrical
outlet to protect it from excessive power surges and current fluctuations.
Note:
Version 1.3
LT-996
Install the MD-990 outside the Touch Screen enclosure.
TX3 Touch Screen Installation Manual
Copyright 2012
23 (53)
Enclosure Installation
The power supply enclosure is shown in Figure 10 (for clarity the power supply
is not shown).
Figure 10. Touch Screen Power Supply Enclosure
To surface mount the power supply enclosure
1.
Find a suitable location for the power supply enclosure, such as over a wall
stud.
2.
Using the power supply enclosure as a template, mark the back mounting
hole locations as indicated in Figure 10. Ensure that at least one side is
over a wall stud.
3.
Remove the power supply enclosure and place the top two screws halfway
into the marked hole locations and wall stud using the supplied screws.
4.
Place the power supply enclosure onto the two screws.
5.
Screw the two screws of the power supply enclosure halfway into the wall.
6.
Tighten all four screws into place.
Note:
24 (53)
The enclosure can also be mounted directly onto the drywall using
anchors.
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
3
Touch Screen System and Setup
This chapter describes the basic Touch Screen system, main panel, controller
board components and provides information about its operation and setup.
This chapter explains
Version 1.3
LT-996
•
Touch Screen System
•
Touch Screen Main Panel
•
Touch Screen Controller Boards
•
Touch Screen Setup
•
Optional Setup Installation
•
Installation Verification
•
PC Configuration of the Controller
•
Firmware Update
TX3 Touch Screen Installation Manual
Copyright 2012
25 (53)
Touch Screen System and Setup
3.1
Touch Screen System
The TX3 Touch Screen may be networked with a combination of Telephone
Access and Card Access Units through a peer-to-peer RS-485 connection.
Touch Screen is capable of providing ADC or NSL telephone access from a
single panel or from a networked system. Each outside telephone line requires a
separate line to the control panel inside the Touch Screen.
The following figures depict various Touch Screen network scenarios.
Note:
Install all transformers and power supplies outside the Touch
Screen enclosure.
All wiring is a maximum length of 1000 ft. The RS-485 wiring maximum length
is 4000 ft.
All units use the MD-990 power supply. Refer to Chapter 2 Installing the Power
Supply Enclosure or document LT-1094 Power Supply Voltage Selection. The
door strike power supply depends on the door strike power requirements.
26 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Touch Screen System and Setup
3.1.1
Single Touch Screen
Figure 11 shows the simplest configuration for an ADC or NSL telephone
system.
Telephone outlet
Central office line
NSL
Control
Unit
T/R
Line1
Line1
OR
Touch Screen
Touch Screen
Figure 11. Single Touch Screen
Version 1.3
LT-996
TX3 Touch Screen Installation Manual
Copyright 2012
27 (53)
Touch Screen System and Setup
Figure 12 shows a configuration using one Touch Screen connected to one ADC
line and four NSL lines.
Telephone outlet
Central office line
T/R
NSL
Control
Unit
NSL
Control
Unit
NSL
Control
Unit
NSL
Control
Unit
T/R
T/R
T/R
T/R
Line2
Line3
Line4
Line1
Line5
Touch Screen
Figure 12. Single Touch Screen with ADC and NSL Lines
3.2
Touch Screen Main Panel
The Touch Screen Panel is situated behind the front cover of the Kiosk. To access
the panel, unlock the Touch Screen and pull open the front cover.
The Touch Screen Panel contains the following main components as shown in
Figure 13:
28 (53)
•
ON/OFF Switch
•
USB Port
•
Camera
•
Postal Lock (optional)
•
Microphone
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Touch Screen System and Setup
Screw
ON/OFF
Switch
Postal Lock
USB Port
Camera
Microphone
Touch Screen
Screw
Figure 13. Touch Screen Panel Components
3.3
Controller Boards
The following Touch Screen controller boards are situated on a panel behind the
Touch Screen Panel as shown in Figure 14:
Version 1.3
LT-996
•
Telephone Access Controller
•
PC Sub Compact Board
•
Power Supply Board
•
Audio Mixer Board
TX3 Touch Screen Installation Manual
Copyright 2012
29 (53)
Touch Screen System and Setup
To access the panel, remove the two screws and swing open the Touch Screen
panel.
Telephone Line
PC Sub Compact Board
Intranet
Telephone
Access
Controller
USB
Power
Terminals
SW1
Microphone and
Speaker Connections
from Telephone
Access Controller
Microphone
Connection
from Touch
Screen
Audio Mixer Board
On/Off
Blk
Wht
USB
Chasis
GND
On/Off
Power Supply Board
Speaker
Connections
Microphone
and Speaker
Connections
to Audio Mixer
Postal Lock
Input 1
Figure 14. Touch Screen Controller Board Panel
For detailed information about the Telephone Access Controller installation and
setup see LT-969 TX3-Telephone Access System Installation and Operation
Manual.
30 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Touch Screen System and Setup
Figure 15 shows the connectors at the top of the Telephone Access controller.
Line 1
T R
Line 5
T R
Line 2 Line 3
T R T R
AC Output 1
Door Strike
Line 4
T R
DC Output 1
Door Strike
General Relay
Output 4
AC or DC
Input Door
Strike Supply
+ -
NC C NO
+ -
NC C NO
JW8
Telephone Lines 1 to 5
Aux. Door
Output 2
Relay
General Relay
Output 3
Figure 15. Controller Board Connectors - Top
Version 1.3
LT-996
TX3 Touch Screen Installation Manual
Copyright 2012
31 (53)
Touch Screen System and Setup
Figure 16 shows the connectors at the bottom of the Telephone Access controller.
Input 2 Input 3 Input 4
- + - + - +
RS-485 OUT
- s +
- +
Microphone
Connection
- +
Input 1
- +
Input 5
- +
Speaker
Connection
LED/LAMP
Supply
- +
Power Supply for TX3
- +
Camera Supply
- s +
RS-485 IN
Figure 16. Controller Board Connectors - Bottom
3.4
Grounding the Touch Screen
Grounding reduces the risk of electrical shock by providing an alternate escape
route for the electrical current. Touch Screen is equipped with a 16 gauge
electrical wire attached to the panel chassis ground post as shown in Figure 14.
To ground the Touch Screen attach one end of the supplied cable to a suitable
grounding wire and connect it to the site ground.
3.5
Connecting to the External Power Supply
The power supply terminal block is situated the middle of the Touch Screen
Controller board panel as shown in Figure 14 and receives 24 Vdc from the
external MD-990 power supply.
The external MD-990 power supply connects to the building power AC power
supply. A voltage selectable switch is located on the side of the unit and is factory
set to 120 V.
For best operation install the external power supply into its own dedicated
electrical outlet to protect it from excessive power surges and current
fluctuations.
32 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Touch Screen System and Setup
All Touch Screen controller boards use the MD-990 for their power supply. The
door strike power supply depends on the door strike power requirements.
Note:
3.5.1
Install the MD-990 outside the Touch Screen enclosure.
Maximum Power Supply Wire Distances
The distance from the Touch screen to the power supply is a function of the wire
gauge and the resistance generated by the cable by the power draw.
Do not exceed the maximum distances from the Touch screen to the power
supply as indicated in Table 1
Table 1:
Maximum Power Supply Wire Distances
Gauge
3.5.2
Distance
16
125 ft (38.1 m)
14
200 ft (60.96 m)
12
320 ft (97.536 m)
10
500 ft (152.4 m)
Wiring the External Power Supply
The power supply terminals are located at the bottom of the MD-990 external
power supply as shown in Figure 17.
+V
L
N
Line
-V -V
+V +V
ADJ
Load
Figure 17. MD-990 Terminal Block Wiring
To connect the power supply
Version 1.3
LT-996
1.
Turn the power off from the Touch Screen Panel.
2.
Ensure the MD-990 voltage selectable switch is set to 120V.
TX3 Touch Screen Installation Manual
Copyright 2012
33 (53)
Touch Screen System and Setup
3.6
3.
Connect the MD-990 lode power supply wires to the Touch Screen
Controller board panel terminal screws as shown in Figure 14.
4.
Connect the building power supply wires to the MD-990 line terminal
screws as shown in Figure 17.
5.
Plug the external MD-990 power supply cord into its own dedicated
electrical outlet.
6.
Turn the power on from the Touch Screen Panel.
Installing the Postal Lock
The system has a built-in micro switch and mounting hardware for a postal lock
installation. If postal service is required, contact the Post Office to obtain the
lock. Figure 14 shows the micro switch input terminal for the postal lock.
Note:
When installing the postal lock leave the micro switch tie wrap in
place. Remove the tie wrap after the postal lock is installed.
Input 1 on the Telephone Access Controller connects to the Postal Lock microswitch.
3.7
Installing the Telephone Lines
Telephone lines 1 to 5 are situated at the top left of the main controller board as
shown in Figure 15. Both NSL and ADC lines can be connected. Each T/R line
is polarity insensitive and can be reversed.
3.8
Installing Optional Components
The optional components consist of the following:
USB keyboard and mouse. The USB connector on the PC Sub Compact Board
allows you the use of these controls at the Touch Screen for configuration
purposes.
Internet/LAN. The Internet/LAN connector on the PC Sub Compact Board
allows you to connect the Touch Screen to the building LAN.
RS-485. An RS-485 terminal lets you easily connect multiple Touch Screen and
telephone and card access controllers across a network. The RS-485 terminal
consists of + (positive), - (negative), and S (Shield) connections. See Figure 16.
34 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Touch Screen System and Setup
There are two additional RS-485 Terminal Connectors that must be added to the
FIRST and LAST node of the network. On the FIRST node of the network attach
the connector to the RS-484 IN. One the LAST node of the network attach the
terminal connector to the RS-485 OUT. See Figure 18.
RS-485 Terminal
Connector
120 Ω
On the LAST Node of network
connect RS-485 Terminal Connector
to RS-485 OUT
- s +
RS-485 OUT
- s +
- s +
RS-485 IN
On the FIRST Node of network
connect RS-485 Terminal Connector
to RS-485 IN
- s +
120 Ω
RS-485 Terminal
Connector
Figure 18. Connecting additional RS-485 Terminal Connector to the First
or Last Node of Network
USB Port. The USB port provides a connection to a PC, for configuring the card
access system and down loading any new firmware.
3.9
Verifying Installed Components
The system is shipped already pre-wired. Before turning on the system it is
important to verify that the following connections are firmly in place. Refer to
Figure 14.
For additional information about the Telephone Access Controller Board
Connectors see LT-969 TX3-Telephone Access System Installation and
Operation Manual:
Version 1.3
LT-996
TX3 Touch Screen Installation Manual
Copyright 2012
35 (53)
Touch Screen System and Setup
Speaker Connections. Audio speakers to Audio Mixer Board.
USB. Telephone Access Controller USB to PC Sub Compact Board USB
Power Supply Connectors. Power connectors from the MD-990 to the power
terminals
Power Connectors.
•
Power connectors from power supply board to PC, controller and audio
mixer board.
•
Power connectors from the power terminals to the Telephone Access
Controller and Power Supply Board.
•
Power connectors from the Power Supply Board/Audio Mixer Board to
the PC Sub Compact Board.
Microphone. Microphone connection to the Audio Mixer Board
Speaker. Speaker connection to the Audio Mixer Board
On/Off Switches.
3.10
•
The Telephone Access Controller power switch is ON by default.
•
The Audio Mixer Board.Power Supply Board power switch is ON by
default.
Beginning Configuration
Ensure that the Telephone Access Controller ID is setup. This address is set by
the SW1 DIP switches on the Telephone Access Controller (Figure 14). The
individual switches are numbered 1 to 8 from left to right, and are marked as
either ON or OFF. The first five switches (1, 2, 3, 4 and 5) set the address ID.
Every TX3 System controller requires a unique ID. The unit ID settings do not
need to be in sequence but it recommended to assign IDs starting from 1, using
increments of one (e.g. 1, 2, 3, 4, etc.). Unit IDs must not be duplicated.
The Touch Screen controller is now ready for configuration. For a complete
description of the configuration and on how establish a connection to the Touch
Screen, see the following documentation:
36 (53)
•
LT-995 Configuration and Administration Guide
•
LT-973 TX3 Configurator Quick Start
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
4
Adding Controllers
This chapter provides information about adding additional controllers on the
same network as the Touch Screen.
This chapter explains
•
Version 1.3
LT-996
How to add the controller
TX3 Touch Screen Installation Manual
Copyright 2012
37 (53)
Adding Controllers
4.1
Adding a Controller
The TX3 Touch Screen may be integrated with other controllers, such as the
Telephone and Card Access systems, through a peer-to-peer connection via the
RS-485 bus.
Touch has a provision to add the TX3 Card Access controller inside the unit.
Note:
Ensure that all network devices each have unique ID addresses.
To integrate another controller
38 (53)
1.
Ensure the Touch Screen and the controller are setup and ready for
operation.
2.
Turn the power OFF for Touch Screen and controller.
3.
Connect the controller to the Touch Screen via the RS-485 bus using the
RS-485 connectors.
4.
Turn the power ON for the Touch Screen and controller.
5.
Connect the PC to either the Touch Screen or controller using the USB
port.
6.
Use the TX3 Configurator Program to add and configure the controller to
the network.
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
5
Appendix
This chapter contains additional information about the TX3 Touch Screen.
This chapter explains
Version 1.3
LT-996
•
Touch Screen Specifications
•
Touch Screen Kits
TX3 Touch Screen Installation Manual
Copyright 2012
39 (53)
Appendix
5.1
Specifications
5.1.1
Operating Temperature
50°C (122°F) to 0°C(32°F).
Do not operate the Touch Screen below 0°C (32°F) at any time.
5.1.2
Telephone Lines
Use only Loop Start telephones (not ground start), check with your local
telephone company.
5.1.3
AC Power Supply
88 Vac to 132 Vac.
5.1.4
External Power Supply
MD-990 156 W, 24 V single output switching power supply.
5.1.5
Door Strikes
Select the appropriate door strike as required by your system applications. We
recommend using the following Mircom door strikes below and its compatible
power transformer.
•
Mircom Model M-10. DC (silent) or AC (buzzing) Door Strike. (Use PS3B transformer)
Note:
5.1.6
The door strike must have its own separate power transformer. Do
not tap or use the system power transformers. When using a
different door strike and door strike transformer, the maximum
strike load that may be switched through the control unit is 28 Vac
or 3.0 Amp DC.
Post Office Lock
The system has a built-in micro switch and mounting hardware for a postal lock
installation. If a postal service is required, contact the Post Office to obtain the
lock.
40 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Appendix
5.1.7
Tamper Switch
This switch can be connected to any security or monitoring system to supervise
the opening of the panel front door. This microswitch is the same type used for
the postal lock. This switch is normally open when the panel front door of the
TX3 is closed, 28 Vac or 28 Vdc, 1A.
5.1.8
RS-485 TX3-USB-AD Kit
The TX3-USB-AD Kit converts RS-485 signals to USB. The MD-993 Module
mounts on the TX3 Telephone or Card Access controller boards. For installation
instructions see LT-6027 TX3-USB-AD Installation Instructions.
5.1.9
TX3-GPM Guard Phone Module
The guard phone connects via a telephone cable to the Guard Phone Module on
the Touch Screen. The TX3-GPM Guard Phone Module mounts on the TX3
Telephone controller board. For installation instructions see LT-972 TX3-GPM
Guard Phone Module Installation Instructions.
Version 1.3
LT-996
TX3 Touch Screen Installation Manual
Copyright 2012
41 (53)
Appendix
42 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
6
Resident Operating Instructions
This chapter describes the Touch Screen operating instructions for use by the
resident.
This chapter explains
Version 1.3
LT-996
•
NSL Resident Operating Instructions
•
ADC Resident Operating Instructions
TX3 Touch Screen Installation Manual
Copyright 2012
43 (53)
Resident Operating Instructions
6.1
NSL Resident Operating Instructions
Mircom's state-of-the-art Touch Screen door entry system provides you and your
guest with an increased level of confidence and security.
Touch Screen operates with your existing telephone. Your guest dials your code
number or selects your name by scrolling through the visual directory on the
Touch Screen unit, causing your telephone to ring.
Note:
6.1.1
The telephone keypad numbers described in this chapter may be
different for your system. If the keypad numbers do not perform as
described, check with your building administrator to get the correct
values.
Granting Access
When you answer your telephone, you will be in communication with your guest.
To unlock the main door
•
Press " 9 " on your telephone keypad. If your unit is assigned a specific
code for the main door then enter this code followed by the pound (#) key.
To unlock the auxiliary door
•
Press " 6 " on your telephone keypad. If your unit is assigned a specific
code for the auxiliary door then enter this code followed by the pound (#)
key.
To refuse entry
6.1.2
•
Hang up or
•
Press “4”. If your unit uses a code for door entry, press “4” followed by the
pound (#) key.
Keyless Entry Codes
The keyless code is a confidential number assigned to each resident by the
building administrator to let you open the front lobby door without using a key.
To unlock the front door
44 (53)
1.
Press “0”. The keyless code prompt appears.
2.
Enter the keyless code. The front door unlocks.
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Resident Operating Instructions
6.1.3
Call Waiting Feature
Note:
The Call Waiting Feature is available only on NSL systems.
When a guest places a call to you from the Touch Screen while you are engaged
in a conversation on your outside telephone line, you will hear a distinct tone.
To answer the call
1.
Briefly push the call waiting key to answer the call. This action
automatically places the outside telephone line "on hold".
2.
While on-line with your guest, you can open the main door by dialing " 9 ".
If your unit is assigned a specific code for the main door then enter this
code followed by the pound (#) key.
3.
To refuse entry, press “4”. If your unit uses a code for door entry, press “4”
followed by the pound (#) key. This disconnects the telephone from the
Touch Screen.
To continue your conversation press “9”, “6” or “4” automatically reconnects to
the previously "on hold" caller.
If your unit uses codes for door entry press either of the codes for allowing entry
through the main or auxilary doors followed by the pound (#) key or press “4”
followed by the pound (#) key.
In a similar manner, you can answer an outside call while talking to the guest in
the lobby.
Note:
Version 1.3
LT-996
You will be disconnected if you attempt to place your guest
"on hold".
TX3 Touch Screen Installation Manual
Copyright 2012
45 (53)
Resident Operating Instructions
6.2
ADC Resident Operating Instructions
Mircom's state-of-the-art Touch Screen door entry system provides you and your
guest with an increased level of confidence and security.
Touch Screen operates with your existing telephone. Your guest dials your code
number or selects your name by scrolling through the visual directory on the
Touch Screen unit, causing your telephone to ring.
Note:
6.2.1
The telephone keypad numbers described in this chapter may be
different for your system. If the keypad numbers do not perform as
described, check with your building administrator to get the correct
values.
Granting Access
When you answer your telephone, you will be in communication with your guest.
To unlock the main door
•
Press " 9 " on your telephone keypad. If your unit is assigned a specific
code for the main door then enter this code followed by the pound (#) key.
To unlock the auxiliary door
•
Press " 6 " on your telephone keypad. If your unit is assigned a specific
code for the auxiliary door then enter this code followed by the pound (#)
key.
To refuse entry
6.2.2
•
Hang up or
•
Press “4”. If your unit uses a code for door entry, press “4” followed by the
pound (#) key.
Keyless Entry Codes
The keyless code is a confidential number assigned to each resident by the
building administrator to let you open the front lobby door without using a key.
To unlock the front door
46 (53)
1.
Press “0”. The keyless code prompt appears.
2.
Enter the keyless code. The front door unlocks.
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Resident Operating Instructions
Version 1.3
LT-996
TX3 Touch Screen Installation Manual
Copyright 2012
47 (53)
Warranty & Warning Information
Limited Warranty
Mircom Technologies Ltd. together with its subsidiaries and affiliates
(collectively, the “Mircom Group of Companies”) warrants the original
purchaser that for a period of two years from the date of manufacture, the product
shall be free of defects in materials and workmanship under normal use. During
the warranty period, Mircom shall, at its option, repair or replace any defective
product upon return of the product to its factory, at no charge for labour and
materials. Any replacement and/or repaired parts are warranted for the
remainder of the original warranty or ninety (90) days, whichever is longer. The
original owner must promptly notify Mircom in writing that there is defect in
material or workmanship, such written notice to be received in all events prior to
expiration of the warranty period.
International Warranty
The warranty for international customers is the same as for any customer within
Canada and the United States, with the exception that Mircom shall not be
responsible for any customs fees, taxes, or VAT that may be due.
Conditions to Void Warranty
This warranty applies only to defects in parts and workmanship relating to
normal use. It does not cover:
•
Version 1.3
LT-996
damage incurred in shipping or handling;
TX3 Touch Screen Installation Manual
Copyright 2012
47 (53)
•
damage caused by disaster such as fire, flood, wind, earthquake or
lightning;
•
damage due to causes beyond the control of Mircom such as excessive
voltage, mechanical shock or water damage;
•
damage caused by unauthorized attachment, alterations, modifications or
foreign objects;
•
damage caused by peripherals (unless such peripherals were supplied by
Mircom);
•
defects caused by failure to provide a suitable installation environment for
the products;
•
damage caused by use of the products for purposes other than those for
which it was designed;
•
damage from improper maintenance;
•
damage arising out of any other abuse, mishandling or improper
application of the products.
Warranty Procedure
To obtain service under this warranty, please return the item(s) in question to the
point of purchase. All authorized distributors and dealers have a warranty
program. Anyone returning goods to Mircom must first obtain an authorization
number. Mircom will not accept any shipment whatsoever for which prior
authorization has not been obtained.
Note:
Unless specific pre-authorization in writing is obtained from
Mircom management, no credits will be issued for custom
fabricated products or parts or for complete fire alarm system.
Mircom will at its sole option, repair or replace parts under
warranty. Advance replacements for such items must be purchased.
Note:
Mircom’s liability for failure to repair the product under this
warranty after a reasonable number of attempts will be limited to a
replacement of the product, as the exclusive remedy for breach of
warranty.
Disclaimer of Warranties
This warranty contains the entire warranty and shall be in lieu of any and all other
warranties, whether expressed or implied (including all implied warranties of
merchantability or fitness for a particular purpose) and of all other obligations or
48 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
liabilities on the part of Mircom neither assumes nor authorizes any other person
purporting to act on its behalf to modify or to change this warranty, nor to assume
for it any other warranty or liability concerning this product.
This disclaimer of warranties and limited warranty are governed by the laws of
the province of Ontario, Canada.
Out of Warranty Repairs
Mircom will at its option repair or replace out-of-warranty products which are
returned to its factory according to the following conditions. Anyone returning
goods to Mircom must first obtain an authorization number. Mircom will not
accept any shipment whatsoever for which prior authorization has not been
obtained.
Products which Mircom determines to be repairable will be repaired and
returned. A set fee which Mircom has predetermined and which may be revised
from time to time, will be charged for each unit repaired.
Products which Mircom determines not to be repairable will be replaced by the
nearest equivalent product available at that time. The current market price of the
replacement product will be charged for each replacement unit.
WARNING
Mircom recommends that the entire system be completely tested on a regular
basis. However, despite frequent testing, and due to, but not limited to, criminal
tampering or electrical disruption, it is possible for this product to fail to perform
as expected.
NOTE
Under no circumstances shall Mircom be liable for any special, incidental, or
consequential damages based upon breach of warranty, breach of contract,
negligence, strict liability, or any other legal theory. Such damages include, but
are not limited to, loss of profits, loss of the product or any associated equipment,
cost of capital, cost of substitute or replacement equipment, facilities or services,
down time, purchaser’s time, the claims of third parties, including customers, and
injury to property.
MIRCOM MAKES NO WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO ITS
GOODS DELIVERED, NOR IS THERE ANY OTHER WARRANTY,
EXPRESSED OR IMPLIED, EXCEPT FOR THE WARRANTY
CONTAINED HEREIN.
Version 1.3
LT-996
TX3 Touch Screen Installation Manual
Copyright 2012
49 (53)
Special Notices
Product Model Number: TX3
AC REN (U.S.): 0.0B
AC REN (CANADA): 0.0
Complies With
Federal Communications Commission (FCC):
•
TIA-968-A Technical requirement for connection of equipment tot he
telephone network.
•
CFR 47, Part 15, Subpart B, Class B
•
Unintentional Radiators
Industry Canada (IC):
•
Terminal attachment programme
•
CS-03, Issue 8 - Certification Specifications
•
ICES-003, ISSUE 4, CLASS B
•
Verification Authorization - Digital Apparatus
Registration Numbers
FCC (U.S.): 1M8OT00BTX3
IC (Canada): 1156A-TX3
Industry Canada Notice for all TX3 Products Sold in Canada
The Industry Canada label identifies certified equipment. This certification
means that the equipment meets certain telecommunications network protective,
operational, and safety requirements. Industry Canada does not guarantee the
equipment will operate to the user's satisfaction. Before installing this
equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunication company. The equipment must also be
installed using an acceptable method of connection. The customer should be
aware that compliance with the above conditions may not prevent degradations
of service in some situations.
50 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alteration made
by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the
equipment. Users should ensure for their own protection that the earth ground
connections of the power utility, telephone lines and internal metallic water pipe
system, if present, are connected together. This is necessary both for proper
operation and for protection.
Caution:
Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or
electrician, as appropriate.
Note:
The Ringer Equivalence Number (REN) assigned to each terminal
device provides an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination
on an interface may consist of any combination of devices subject
only to the requirement that the sum of the RENs of all the devices
does not exceed five.
FCC Notice for all TX3 Products Sold in the U.S.A.
Type of Service
The TX3 is designed to be used on standard device telephone lines. It connects to
the telephone line by means of a standard jack called the USOC RJ-11C (or
USOC FJ45S). Connection to telephone company-provided coin service (central
office implemented systems) is prohibited. Connection to party lines service is
subject to state tariffs.
Telephone Company Procedures
The goal of the telephone company is to provide you with the best service it can.
In order to do this, it may occasionally be necessary for them to make changes in
their equipment, operations or procedures. If these changes might affect your
service or the operation of your equipment, the telephone company will give you
notice, in writing, to allow you to make any changes necessary to maintain
uninterrupted service.
In certain circumstances, it may be necessary for the telephone company to
request information from you concerning the equipment which you have
connected to your telephone line. Upon request of the telephone company,
provide the FCC registration number and the ringer equivalence number (REN);
both of these items are listed on the equipment label. The sum of all of the RENs
Version 1.3
LT-996
TX3 Touch Screen Installation Manual
Copyright 2012
51 (53)
on your telephone lines should be less than five in order to assure proper service
from the telephone company. In some cases, a sum of five may not be useable on
a given line.
Changes to Telephone Service
The telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment. If this
happens the telephone company will provide advance notice in order for you to
make necessary modifications to maintain uninterrupted service.
Ringer Equivalence Number
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most but not all areas, the sum of
RENs should not exceed five (5.0). To be certain of the number of devices that
may be connected to a line, as determined by the total RENs, contact the local
telephone company. For products approved after July 23, 2001, the REN for this
product is Customer Information 3 July 2003 part of the product identifier that
has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the
REN is separately shown on the label.
If Problems Arise
If any of your telephone equipment is not operating properly, you should
immediately remove it from your telephone line, as it may cause harm to the
telephone network. If the telephone company notes a problem, they may
temporarily discontinue service. When practical, they will notify you in advance
of this disconnection. If advance notice is not feasible, you will be notified as
soon as possible. When you are notified, you will be given the opportunity to
correct the problem and informed of your right to file a complaint with the FCC.
Contact your telephone company if you have any questions about your telephone
line. In the event repairs are ever needed on the Communicator, they should be
performed by Mircom or an authorized representative of Mircom. For
information contact Mircom at the address and telephone numbers in
paragraph 1.7.
If this equipment, TX3 Telephone System, causes harm to the telephone network,
the telephone company will notify you in advance that temporary discontinuance
of service may be required. But if advance notice isn't practical, the telephone
company will notify the customer as soon as possible. Also, you will be advised
of your right to file a complaint with the FCC if you believe it is necessary.
52 (53)
TX3 Touch Screen Installation Manual
Copyright 2012
Version 1.3
LT-996
Product Identifier
This equipment complies with Part 68 of the FCC rules and the requirements
adopted by the ACTA. On the back of the front panel cover of this equipment is
a label that contains, among other information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this number must be provided to the
telephone company.
Telephone Connection
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. You are responsible for installing a
compliant telephone cord and modular plug into this product as described in this
manual. It is designed to be connected to a compatible modular jack that is also
compliant. See installation instructions for details.
Equipment Failure
If trouble is experienced with the TX3 Telephone/Card Access System, for repair
or warranty information, please contact Mircom using the numbers
paragraph 1.7. If the equipment is causing harm to the telephone network, the
telephone company may request that you disconnect the equipment until the
problem is resolved.
Use With Alarm Auto Dialers
If your institution has specially wired alarm equipment connected to the
telephone line, ensure the installation of the TX3 Telephone/Card Access System
does not disable your alarm equipment. If you have questions about what will
disable alarm equipment, consult your telephone company or a qualified
installer.
Version 1.3
LT-996
TX3 Touch Screen Installation Manual
Copyright 2012
53 (53)