Craftsman 315.101280 Owner`s manual

OWNER'S
MANUAL
MODEL_NO.
315.101280
CAUTION:
Read and follow
ALL safety rules
and instructions
before operating
this equipment.
CRAFTSMAN°
1/2 Inch Drill
Variable Speed
Adjustable- Reversible
DOUBLE INSULATED
Thank You for Buying
Craftsman
Drill
A
Rules for Safe Operation
Warranty
Operation
Maintenance
Repair Parts
Sold by SEARS, ROEBUCK AND CO., Hoffman Estates,
972000-144
7-00
®
IL 60179 U.S.A.
Printed In U.S.A.
RULES FOR SAFE OPERATION
DOUBLE INSULATION is a concept in safety, in electric
power tools, which eliminates the need for the usual three
wire grounded power cord and grounded supply system.
Wherever there is electric current in the tool there are two
complete sets of insulation to protect the user. All exposed
metal parts are isolated from internal metal motorcomponents
with protecting insulation.
READ
1
ALL
IMPORTANT - Servicing of a tool with double insulation
requires extreme care and knowledge of the system and
should be performed only by a qualified service technician.
For service we suggest you return the tool to your nearest
Sears Store for repair. Always use original factory replacement
parts when servicing.
INSTRUCTIONS
KNOW
YOUR
POWER
TOOL.
Read
10.
owner's
Pipes, radiators,
3.
KEEP GUARDS
4.
KEEP WORK AREA CLEAN.
benches invite accidents.
5.
IN PLACE
Cluttered
7.
order.
areas and
AVOIDDANGEROUSENVIRONMENT.Don't
9.
air vents.
11. ALWAYS WEAR SAFETY GLASSES.
Everyday
eyeglasses have only impact-resistant lenses; they
are NOT safety glasses.
12.
PROTECT
YOUR LUNGS.
Wear a face mask or
dust mask if operation is dusty.
use
PROTECT
YOUR
HEARING.
Wear hearing
protection during extended periods of operation.
All
14.
visitors should wear safety glasses and be kept a
safe distance from work area. Do not let visitors
contact tool or extension cord.
DON'T ABUSE CORD. Never carry tool by cord or
yank it to disconnect from receptacle. Keep cord
from heat, oil and sharp edges.
15.
SECURE
KEEP
CHILDREN
STORE
IDLE
AND
TOOLS.
VISITORS
When
or expose
to
AWAY.
16.
DON'T FORCE TOOL. It will do the job better and
safer at the rate for which it was designed.
USE
RIGHT
TOOL.
Don't
force
small
tool
WORK.
Use clamps or a vise to hold
work. Both hands are needed to operate the tool.
not in use tools
should be stored in a dry and high or locked-up
place - out of the reach of children.
8.
Do not wear loose
13.
power tool in damp or wet locations
rain. Keep work area well lit.
6.
drawn into nearby
ranges, refrigerator
and in working
APPAREL.
gloves and non-skid footwear are recommended
when working
outdoors.
Wear protective
hair
covering to contain long hair and keep it from being
GUARD
AGAINST
ELECTRICAL
SHOCK
by
preventing
body contact with grounded surfaces.
For example:
enclosures.
PROPER
clothing or jewelry that can get caught in tool's
moving parts and cause personal injury. Rubber
manual
carefully.
Learn
its applications
and
limitations as well as the specific potential hazards
related to this tool.
2.
WEAR
DON'T OVERREACH.
Keep proper footing and
balance at all times. Do not use on a ladder or
unstable support.
17.
or
attachment to do the job of a heavy duty tool. Don't
use tool for purpose not intended - for example - A
circular saw should never be used for cutting tree
limbs or logs.
Page 2
MAINTAIN TOOLS WITH CARE. Keep tools sharp
at all times, and clean for best and safest
performance.
Follow instructions for lubricating
and changing accessories.
RULES FOR SAFE OPERATION
20.
(Continued)
AVOID ACCIDENTAL
STARTING.
Don't carry
plugged-in tools with finger on switch. Be sure
switch is off when plugging in.
21.
MAKE
SURE
YOUR
GOOD
CONDITION.
31.
EXTENSION
When
service center unless
instruction manual.
CORD
IS IN
using an extension
cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord
will cause a drop in line voltage resulting in loss of
power and overheating. A wire gage size (A.W.G.)
of at least 16 is recommended
for an extension
cord 100 feet or less in length. A cord exceeding
100 feet is not recommended.
If in doubt, use the
next heavier gage. The smaller
the heavier the cord.
22.
OUTDOOR
USE EXTENSION
the gage number,
CORDS.
KEEP
BITS
CLEAN
AND
SHARP.
When tool
Sharp
KEEP HANDS
AWAY
FROM
33.
bits
34.
INSPECT
TOOL CORDS
INSPECT
EXTENSION
DRILLING
KEEP
FROM
37.
and if
30.
CHECK
brake fluids,
or any strong
Watch what you are doing and use
common sense. Do not operate
tired. Do not rush.
DAMAGED
tool while under the influence
or any medication.
Do not
of drugs,
PLUGS.
To reduce the risk of electric
contact a qualified electrician to install the proper
outlet. Do not change the plug in any way.
HANDLES
DRY, CLEAN,
AND FREE
OIL AND GREASE. Always use a clean
STAY ALERT.
MEDICATION.
wider than the other). This plug will fit in a polarized
outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit,
PERIODICALLY
cloth when cleaning.
Never use
gasoline, petroleum-based
products
solvents to clean your tool.
29.
ALCOHOL,
POLARIZED
and replace if damaged.
28.
DRUGS,
36.
AREA.
ATMOSPHERE.
PERIODICALLY
CORDS
all nails from lumber
WHEN
SERVICING
USE ONLY IDENTICAL
CRAFTSMAN
REPLACEMENT
PARTS.
damaged, have repaired at your nearest Sears
Repair Center. Stay constantly aware of cord
location.
27.
FOR and remove
shock, this tool has a polarized plug (one blade is
Normal sparking of the motor could ignite fumes.
26.
INSPECT
35.
to remove material while bit is rotating.
NEVER USE IN AN EXPLOSIVE
center.
DRILLING
INTO ELECTRICAL
WIRING
IN
WALLS CAN CAUSE DRILL BIT AND CHUCK
TO BECOME ELECTRICALLY
LIVE. Do not touch
operate
alcohol,
Keep hands away from bits. Do not reach
underneath work while bit is rotating. Do not attempt
25.
service
the chuck or metal housing when drilling into a wall;
grasp only the insulated handle(s) provided on the
tool.
minimize stalling and kickback.
24.
by an authorized
before drilling.
is used outdoors, use only extension cords suitable
for use outdoors.
Outdoor approved
cords are
marked with the suffix W-A, for example - SJFW-A
or SJOW-A.
23.
in this
DO NOT USE TOOL IF SWITCH
DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced
32.
indicated elsewhere
tool when you are
PARTS. Before further use of
the tool, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting,
and
any other conditions that may affect its operation.
A guard or other part that is damaged should be
properly repaired or replaced by an authorized
Page 3
SAVE
THESE
INSTRUCTIONS.
Review
them
frequently and use them to instruct others who may
use this tool. If you loan someone this tool, loan
them these instructions also.
INTRODUCTION
CONGRATULATIONS
THIS CRAFTSMAN
AND THANK YOU FOR BUYING
1/2 INCH DRILL. It has been
designed, engineered and manufactured to provide you with
Sears high standard of dependability, ease of operation,
and operator safety. Properly cared for, it will give you years
of rugged, trouble-free performance.
through
read
this entire owner's
using your new drill. Pay close attention to
the Rules For Safe Operation, Warnings and Cautions. If
you use your drill properly and only for what it is intended,
you will enjoy years of safe, reliable service.
SPECIFICATIONS:
1/2 In.
Chuck Capacity
3/8
Horsepower
Rating
120 Volts, 60 Hz, AC only, 3.5 AMPS
_reCarefully
Your drill has many features for
operations
more pleasant
and
performance and dependability have
in the design of this drill making it
operate.
0 - 600 RPM
No Load Speed
Switch
Adjustable Variable Speed/Reversible
making your drilling
enjoyable.
Safety,
been given top priority
easy to maintain and
FULL ONE YEAR WARRANTY ON CRAFTSMAN
DRILL
If this Craftsman Drill fails to give complete satisfaction within one year from the date of purchase, RETURN IT TO
THE NEAREST SEARS STORE IN THE UNITED STATES, and Sears will repair it, free of charge.
If this Craftsman Drill is used for commercial or rental purposes, this warranty applies for only 90 days from the date
of purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., DEPT. 817 WA, Hoffman Estates, IL 60179
TABLE OF CONTENTS
1.
Rules for Safe Operation
............................................................................
2.
Introduction
3.
Warranty andTable
4
Operation
5.
Maintenance and Accessories
6.
Exploded View and Parts List .................................................................
7.
Parts Ordering / Service ..............................................................................
and Product Specifications
........................................................
of Contents .....................................................................
....................................................................................................
.....................................................................
2-3
4
4
5-9
10
12-13
14
The operation of any drill can result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power tool operation, always wear safety
goggles or safety glasses with side shields and a full face shield when needed. We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses
with side shields, available at Sears Retail Stores.
Page 4
OPERATION
KNOW
YOUR
ELECTRIC
DRILL
Before attempting to use your drill, familiarize yourself with all operating features and safety requirements. See Figure 1.
ELECTRICAL
CONNECTION
Your drill has a precision built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only
(normal household current). Do not operate this tool on direct current (DC). A voltage drop of more than 10 percent will
cause a loss of power and the motor will overheat. If your tool does not operate when plugged into an outlet, double-check
the power supply.
AUXILIARYHANDLE
/
"D" SHAPED
HANDLE
CHUCKKEYSTORAGE
TO STORE
LOCK-ONBu'n'ON
CHUCKKEY
TO REMOVE
Fig. 1
J
Page 5
OPERATION
SWITCH
See Figure 2.
To turn your drill ON, depress switch trigger. Release switch
trigger to turn your drill OFF.
LOCK-ON B u'n'ON
See Figure2.
Your drill is equipped with a "lock-on" feature, which is
convenient when continuous drilling for extended periods of
time is required. To lock-on, depress the switch trigger, push
in and hold the lock-on button located on the side of the
handle, then release switch trigger. Release lock-on button
and your drill will continue running.
To release the lock, depress the switch trigger and release it.
If you have the "lock-on" feature engaged du ring use and you r
drill becomes disconnected from power supply, disengage
the "lock-on" feature immediately.
SWITCHTRIGGER
LOCK-ONBUTTON
Fig. 2
FORWARD-REVERSE
LEVER
REVERSIBLE
See Figure3.
Your drill has the feature of being reversible. The direction of
chuck rotation is controlled by a lever located above the
switch trigger. With yourdrin held in normal operating position,
the rotation lever should be positioned to the left of the switch
for drilling, The direction of rotation is reversed when the lever
is to the right of the switch.
THE DESIGN OF THE SWITCH WILL NOT PERMIT
CHANGING THE DIRECTION OF ROTATION WHILE THE
DRILL IS RUNNING. RELEASE THE SWITCH TRIGGER
AND ALLOW THE DRILL TO STOP BEFORE CHANGING
ITS DIRECTION.
REVERSE
FORWARD
Fig, 3
CHUCKKEYSTORAGE
TO STORE
NOTE: YOUR DRILL WILL NOT RUN UNLESS THE
SWITCH LEVER IS PUSHED FULLY TO THE LEFT OR
RIGHT.
CHUCK
KEY
See Figure 4.
A chuck key has been provided for use when installing or
removing bits, it is also used when removing the chuck. (See
chuck removal section.)
CHUCK
KEY STORAGE
See Figure 4.
When not in use, the chuck key can be placed in the storage
area located on the bottom portion of drill handle.
•
Page 6
TO REMOVE
Fig. 4
OPERATION
VARIABLE
SPEED
VARIABLESPEED
CONTROLSELECTOR
See Figure 5.
Your drill has a variable speed control selector designed to
allow operator control and adjustment of speed and torque
limits. The speed and torque of your drill can be increased or
decreased by rotating the variable speed control selector in
the direction of the arrows shown in figure 5.
NOTE: Hold your drill in normal operating position and turn
the variable speed control selector clockwise to increase the
speed and torque of your drill. Turn counterclockwise to
decrease the speed and torque of your drill.
If you desire to lock the switch on at a given speed, depress
the switch trigger, push in and hold the lock-on button, and
release the switch trigger. Next, adjust the variable speed
control selector until the desired speed is reached.
NOTE: IF THE VARIABLE SPEED CONTROL SELECTOR
IS FULLY TURNED
IN THE COUNTERCLOCKWISE
DIRECTION (ZERO SETTING) YOUR DRILL MAY NOT
RUN.
TO INCREASESPEED
TO DECREASESPEED
Fig. 5
IF YOU DESIRE NOT TO USE THE VARIABLE SPEED
CONTROL
SELECTOR,
TURN IT IN THE FULL
CLOCKWISE DIRECTION. THIS WILL ALLOW THE SPEED
OF YOUR DRILL TO BE FULLY CONTROLLED BY THE
AMOUNT OF SWITCH TRIGGER DEPRESSION.
Avoid running your drill at low speeds for extended periods of
time. Running at low speeds under constant usage may
cause your drill to become overheated. If this occurs, cool
your drill by running it without a load and at full speed.
The following guidelines may be used in determining correct
speed for various applications:
LOW speed is ideal when minimum speed and power is
required. For example: starting holes without center punching,
driving screws, mixing paint, and drilling in ceramics.
MEDIUM speed is suitable for drilling hard metals, plastics,
and laminates.
HIGH speed produces best results when maximum power is
required. For example: drilling in wood; soft metals such as
aluminum, brass, and copper; and when using driving
accessories.
INSTALLING
AUXILIARY
HANDLE
See Figure 1, Page 5.
AN AUXILIARY HANDLE IS PACKED WITH YOUR DRILL
FOR EASE OF OPERATION AND TO HELP PREVENT
LOSS OF CONTROL. To install, start the screw threads into
the threaded hole in the gear housing and tighten securely.
NOTE: For convenience the screw has been trapped inside
the auxiliary handle.
To prevent thread damage and possible loss of control,
auxiliary handle should be checked periodically for tightness.
DO NOT operate drill with handle loose.
INSTALLING"D"SHAPED
HANDLE
See Figure 6.
A multi-position "D" shaped handle is also packed with your
drill. It is used for maintaining proper balance and control of
your drill. To install, place handle in desired position on star
shaped mounting boss. Mounting boss is located on the end
of your drill. Add washer then insert screw. To tighten screw,
insert screwdriver through side of handle as shown in figure 6.
Tighten screw securely, then remove screwdriver.
Page 7
OPERATION
TO INSTALL
BITS
See Figure 7.
1. UNPLUG YOUR DRILL.
2.
3.
Open or close the chuck jaws to a point where the
opening is slightly larger than the drill bit you intend to
use. Also, raise the front of your drill slightly to keep the
drill bits from falling out of the chuck jaws.
Insert drill bit into chuck the full length of the jaws.
4,
Tighten chuck jaws securely, using only the chuck key
provided. DO NOT USE A WRENCH TO TIGHTEN OR
LOOSEN THE CHUCK JAWS.
5,
Remove chuck key and return to storage area.
RIGHT
Fig. 7
WRONG
Fig. 8
DRILLING
See Figure 9.
1,
Depress and release switch trigger to be sure your drill
is in "Off" position before connecting it to power
supply.
2.
Check the direction of rotation lever for correct setting
(forward or reverse). See Figure 3.
3,
Secure the material to be drilled in a vise or with clamps
to keep it from turning as the drill bit rotates.
4.
Plug your drill into power supply source.
5.
Hold your drill firmly and place bit at point to be drilled.
6.
Depress the switch trigger to start your drill. Do not lock
the switch "On" for jobs where your drill may need to
be stopped suddenly.
7.
Move the drill bit into the workpiece applying only
enough pressure to keep the bit cutting. Do not force
your drill or apply side pressure to elongate a hole. Let
your drill and bit do the work. See Figure 9.
TO REMOVE
BITS
1.
UNPLUG YOUR DRILL.
2.
3.
Loosen chuck jaws using only the chuck key provided.
DO NOT USE A WRENCH TO TIGHTEN OR LOOSEN
THE CHUCK JAWS.
Remove drill bit from chuck jaws.
4.
Remove chuck key and return to storage area.
Page
/
Fig. 9
OPERATION
When drilling hard, smooth surfaces use a center punch to
mark the desired hole location. This will prevent the drill bit
from slipping off center as the hole is started.
When drilling metals, use a light oil on the drill bit to keep it
from overheating. The oil will prolong the life of the bit and
increase the drilling action.
CHUCK
CHUC
JAWS_
If the bit jams in the workpiece or if your drill stalls, stop the
tool immediately. Remove the bit from the workpiece and
determine the reason for jamming.
CHUCK
REMOVAL
See Figures 10, 1 I, and 12.
The chuck must be removed in orderto use some accessories.
To remove:
"
Fig. 10
1.
UNPLUG YOUR DRILL.
2.
Close chuck jaws. Insert chuck key into chuck and tap
sharply with a mallet in a clockwise direction. See
Figure 10. This will loosen chuck screw for removal.
Open the chuck jaws and remove the chuck screw by
turning it in clockwise direction. See Figure 11. NOTE:
Chuck screw has left hand threads.
3.
4.
5.
CHUCK
KEY
Insert chuck key into chuck and tap sharply with a
mallet in a counterclockwise direction. This will loosen
Fig. 11
it on spindle. It can now be unscrewed by hand. See
Figure 12.
Remove chuck key and return to storage area.
TO RETIGHTEN
A LOOSE
CHUCK
The chuck may at times become loose on the spindle and
develop a wobble. Also, the chuck screw may become loose
causing the chuck jaws to bind and prevent them from
closing. To tighten, follow these steps:
1,
UNPLUG YOUR DRILL.
2.
3.
Open the chuck jaws.
Insert chuck key into chuck and tap sharply with a
mallet in clockwise direction. This will tighten the chuck
on spindle.
Tighten chuck screw. NOTE: Chuck screw has left
hand threads.
4.
5.
Fig. 12
Remove chuck key and return to storage area.
Page 9
MAINTENANCE
GENERAL
Only the parts shown on parts list, page 13, are intended to be
repaired or replaced by the customer. All other parts represent
an important part of the double insulation system and should
be serviced only by a qualified Sears service technician.
Avoid using solvents when cleaning plastic parts. Most plastics
are susceptible to various types of commercial solvents and
may be damaged by their use. Use clean cloths to remove dirt,
carbon dust, etc.
It has been found that electric tools are subject to accelerated
wear and possible premature failure when they are used on
fiberglass
boats, sports cars, walrboard,
spackling
compounds, or plaster. The chips and grindings from these
materials are highly abrasive to electric tool parts such as
bearings, brushes, commutators, etc. Consequently, it is not
recommended that this tool be used for extended work on
any fiberglass material, wallboard, spackling compounds, or
plaster. During any use on these materials, it is extremely
important that the tool is cleaned frequently by blowing with
an air jet,
THE FOLLOWING RECOMMENDED ACCESSORIES ARE CURRENTLY
AVAILABLE AT SEARS RETAIL STORES,
High Speed Bits (For wood or metal)
Masonry Bits
Wood Boring Bits
1/2 In. Max.
3/4 In. Max.
1-1/2 In. Max.
The use of attachments or accessories
EXTENSION
Hole Saws
2-1/2 In. Max.
1/2 In. Chuck (_9-2980)
not listed above might be hazardous.
CORDS
The use of any extension cord will cause some loss of power. To keep the loss to a minimum and to prevent tool overheating,
use an extension cord that is heavy enough to carry the current the tool will draw.
A wire gauge size (A.W.G.) of at least 16 is recommended for an extension cord 100 feet or less in length. When working
outdoors, use an extension cord that is suitable for outdoor use. The cord's jacket will be marked WA.
_]1_
Keep extension cords away from the drilling area and position the cord so that it will not get caught on lumber,
tools, etc. during drilling operation.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal
operating conditions. Therefore, no further lubrication is required.
Page 10
NOTES
Page 11
CRAFTSMAN
1/2 INCH
DRILL - MODEL NUMBER
315.101280
11
13
-_-12
14
8
3
4
6
7
18
21 19 20
SEE NOTE "A", Page 13
15
CRAFTSMAN
I
1/2 INCH
DRILL -- MODEL NUMBER
315.101280
The
or
ordering
model number
repair parts,
will be found on a plate attached to the motor housing, Always mention the model number of your DRILL when requesting service
PARTS LIST
Key
No.
Part
Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
613150-003
973110-001
968703-013
972724-004
990963-001
620789-003
972706-001
972717-001
931744-063
990952-001
972845-001
972895-002
972877-001
703493-819
617205-006
972846-001
17
18
19
20
21
22
Description
Quan.
Screw (#5/16-24 x 7/8 In. Fil. Hd. Left Hand) .........................................................................................................
1/2 In. Chuck ............................................................................................................................................................
1
1
Screw (#8-32 x 7/8 In. Pan Hd. T,F.) .......................................................................................................................
Gear Housing (Includes Key Nos. 5, 8, and 21) .....................................................................................................
Spindle Bearing .......................................................................................................................................................
Spring Washer .........................................................................................................................................................
Gear and Spindle Assembly ....................................................................................................................................
Sleeve Bearing ........................................................................................................................................................
Washer ....................................................................................................................................................................
4
1
1
1
1
1
2
Gear and Pinion .......................................................................................................................................................
1
Logo Plate ................................................................................................................................................................
Auxiliary Handle .......................................................................................................................................................
"D" Shaped Handle ..................................................................................................................................................
Washer ....................................................................................................................................................................
1
1
1
1
989067-002
703774-005
931055-011
Screw (#1/4-20 x 7/8 In. Pan Hd.) ...........................................................................................................................
Data Plate ................................................................................................................................................................
Thrust Washer .........................................................................................................................................................
Ball ...........................................................................................................................................................................
Washer ....................................................................................................................................................................
1
1
1
1
2
990953-001
990962-001
606858-001
972000-144
Cluster Gear and Shaft Assembly ...........................................................................................................................
Bearing ....................................................................................................................................................................
Chuck Key ...............................................................................................................................................................
Owner's Manual
1
1
1
,t
NOTE: "A" -- The assembly shown represents an important part of the Double Insulated System. To avoid the possibility of alteration or damage
to the System, repairs should be performed by your nearest Sears Service Center. Contact your nearest Sears Retail Store for Service Center
information.
* Standard Hardware Item -- May Be Purchased Locally
** Available From Division 98 -- Source 980.00
Paae 13
J
]
Get it fixed, at
For repair of major brand appliances in your own home...
no matter who made it, no matter who sold it!
1-800-4-MY-HOME
sMAnytime,
day or night
(1°800-469-4663)
www.sears,com
To bring tn products such as vacuums, lawn equipment and electronics
for repair, call for the location of your nearest Sears Parts & Repair Center.
1-800-488-1222
Anytime,
day or night
www.sears.com
For the replacement parts, accessories and owner's manuals
that you need to do-it-yourself, call Sears PartsDirectSM!
1-800-366-PART
6 a.m. - 11 p.m. CST,
(1-800-366-7278)
_
)
..........................
7 days a week
www'sears_cQ_Pa_Sdjrect
!_ii
........................................
To purchase or inquire about a Sears Service Agreement:
_ii
_
!_!"
_:_!:
1-800-827-6655
7 a.m. - 5 p.m. CST, Mon. - Sat.
Para pedir servieio de reparaci6n
y para ordenar
a domicilio,
Au Canada
pour service
en fran_ais:
1-877-LE-FOYER
piezas con entrega
a domicilio:
SM
1-888-SU-HOGAR
s.
(_1877 -533 - 6937 )
(1-666-784-6427)
,
........
® Registered Trademark / _M Trademark
® Sears, Roebuck ;_ndCo
i_!:_:
!_
f sH s 1
LHomeCentral '°]
I
_
!
I
_
......_
of Sears1 Roebuck and Co
® M_lrcel RegJstrada / T_ Marca de Fabrica de Sears, Roebuck and Co,
_
-;_÷_ _,_